Chronic stress in dairy cattle industry has negative impacts on animal health, productivity, and welfare. It has been confirmed that cortisol transfers to milk and resists the high temperature during milk processing. This study evaluated the relationship between milk cortisol concentration (MCC) in commercial milk products and the temperature-humidity index (THI) at time of milk production. Eleven commercially produced pasteurized and sterilized milk products, purchased in Chuncheon, Korea, with production dates ranging from July to October 2021 were analyzed. The MCC was extracted using diethyl ether and analyzed using enzyme immunoassay. Average THI values based on microclimate data provided by the Korea Meteorological Administration were 77±0.8, 75±1.4, 69±1.4, and 58±1.8, in July, August, September, and October, respectively. The average MCC levels were 211.9±95.1, 173.5±63.8, 109.6±53.2, and 106.7±33.7 pg/mL in July, August, September, and October, respectively. MCC in July was higher than in August, September and October (p<0.05), while it was lower in September and October than in August (p<0.05). Significant variations in MCC were observed in commercial milk products across the four production months (p<0.05), except for two milk products. Overall, monitoring cortisol residue in commercial dairy milk products can be an alternative indicator of stress in dairy cattle of farms.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

This article investigated whether the atmospheric temperature had any role in the spread and vulnerability to COVID-19 worldwide and how that knowledge can be utilized to contain the fast-spreading disease. It highlighted that temperature was an important factor in transmitting the virus, and a moderately cool environment was the most favourable state for its susceptibility. In fact, the risk from the virus is reduced significantly in high temperature environment. Warm countries and places were likely to be less vulnerable. We identified various degrees of vulnerability based on temperature and specified countries for March and April. The maximum reported case, as well as death, was noted when the temperature was in the range of around 275°K (2°C) to 290°K (17°C). Countries like the USA, UK, Italy and Spain belonged to this category. The vulnerability was moderate when the temperature was less than around 275°K (2°C) and countries in that category were Russia, parts of Canada and few Scandinavian countries. For temperature 300°K (27°C) and above, a significantly lesser degree of vulnerability was noted. Countries from SAARC, South East Asia, the African continent and Australia fell in that category. In fact, when the temperature was more than 305°K (32°C), there was a unusually low number of reported cases and deaths. For warm countries, further analyses on the degree of vulnerability were conducted for the group of countries from SAARC and South East Asia and individual countries were compared. We also showed countries can switch from one vulnerability state to another based on the variability of temperature. We provided maps of temperature to identify countries of different vulnerability states in different months of the year. That influence of temperature on the virus and previous results of clinical trials with similar viruses gave us a useful insight that regulating the level of temperature can provide remarkable results to arrest and stop the outbreak. Based on that knowledge, some urgent solutions are proposed, which are practically without side effects and very cost-effective too.

Algaecides are chemicals that cause serious health problems. Conventional paints contain algaecides to improve the algae resistance on the paint film. Present research has suggested an environmental friendly paint formulation that focuses on developing algae resistance without having algaecides. In this research, Algae growth on newly developed paint is modeled by incorporating dirt resistance of paint and natural phenomena including humidity, temperature and time respectively. The fitted Model revealed explained variation of 59.65% in the average algae growth, of which, Dirt Resistance, Humidity and temperature and some of their interactions play significant role in this variation. Model suggests that the proposed newly developed paint without algaecides is more resilient to algae growth and significantly decreased the average algae growth rate by 0.53% as compared to conventional paints. Keeping the effect of all other factors constant, if dirt resistance of paint (D_c value) increases by one percent, average algae growth decreases by 12.98%; when temperature increases by 1^oC, average algae growth decreases by 22.4%; a positive unit change in the joint linear effect dirt resistance, temperature and humidity caused a decrease in average algae growth by 0.0031%. It was also observed that the individual effect of humidity variable was inversely related with average algae growth. However the combination of humidity and temperature, humidity and dirt resistance, humidity and time, and the quadratic effect of humidity were found to increase the average algae growth rate. The cubic effect of temperature variable by one degree centigrade resulted in decrease of average algae growth by 0.000907%.

A highly dirt resistant paint for building facades without chemicals harmful to nature and environment, is developed which resolves the unattractive disfigurement of building walls caused by dirt. The experimentation is scientifically and statistically planned with the aid of computer programming. It consists of a sequence of phases which include the selection of appropriate raw materials, adopting of Basic Language computer programming to generate a target population of paint formulations. The average PVC percentage is computed using theory and found to be 54.98% for the target population of 543143 paint formulations hence verifies the literature results. Experimentation and statistical analysis are performed to compare the classical conventional agitator with latest lab equipment like Nano mill and it is concluded that Nano mill performs better on the average than conventional agitator in preparation of paint formulations. Hence the sample of paint formulations is prepared on Nano mill and tested in laboratory using advanced available technology for the analysis and comparison of paint properties to determine the best paint formulation. The results are analyzed using Analysis Of Variance Technique (ANOVA) and it is concluded that the paint formulation named “O3” has the highest dirt resistance on the average. The final selected formula O3 is compared with three other competitor paints in market under natural environment for a period of almost one year. A regression model is also constructed to study the effect of environmental factors like time, temperature and humidity on dirt resistance of paints. It is found that O3 formulation is the best environment friendly which performs equally well with one competitor paint and has higher dirt resistance than two other competitor paint formulations containing harmful chemicals. The regression model of dirt resistance on variables including time, temperature and humidity shows that these factors are significantly affecting the dirt resistance of a given paint at 5% level of significance. 95.34% variation in the dirt resistance of a given paint is due to and explained by the given factors. The regression model is useful to predict the average dirt resistance of a given paint with a certain level of confidence. The project exemplifies the work of an applied research from conceptualization to successful commercialization for the paint industry.

The coronavirus disease 2019 (COVID-19), the pandemic is an unprecedented health emergency never seen in the recorded history of humankind due to its sheer scale, rapid spread, and subsequent shock to the global economy. The past respiratory viral pandemics of the 21st century (SARS-CoV-2 in 2003, Influenza AH1N1 in 2009) have revealed seasonality in environmental factors to play a role in the dynamics of their spread. Here, we report the observed state-level relationship between environmental factors such as temperature (T), relative humidity (RH), specific humidity (SH), and solar radiation (SR) on the COVID-19 spread over the Indian region. The results show that T and RH have a significant impact on the disease growth rate and doubling time. Every degree rise in temperature corresponds to a 0.99 % decrease in the number of cases and an increase in doubling time by ~ 1.13 days implying a slowing down of spread. A similar analysis for RH reveals that more moisture leads to a higher growth rate and reduced doubling time. Lower SH and higher surface-reaching SR are found to reduce the spread and increase the doubling time similar to that of temperature. The range of average state-level T (RH) encountered during this period was between 24 and 35^oC (30 and 87%) which implies that environmental impact is still effective at all these T (RH) and is not limited to specific T (RH) ranges. The progression of the season towards monsoon, post-monsoon, and thereafter winter with a continuous reduction in temperature will prove a major challenge for health workers and policymakers attempting to enforce mitigation and control measures.

The pandemic threat SARS-CoV-2 is now beyond control though the country of origin of this virus had already been limited for the new infection. Number of infected people and countries have been increasing day by day. Considering the previous pandemic flues, it is hypothesizing that COVID-19 will be reduced with warming the global environmental temperature. Therefore, the current study was aimed to analyze the effect of temperature and relative humidity (RH) on spreading of SARS-CoV-2 infection. The COVID-19 confirmed cases of 31 different states in China and 70 cities of 11 countries were obtained from several online databases. The real time temperature and humidity of the respective regions were taken from an online weather forecasting data source. Correlation analyses showed that SARS-CoV-2 infectivity and spreading negatively correlated with temperature of most of the states of China or cities of the world or in a country. The effect of humidity on COVID-19 was found to be positively correlated inside the China and difference of humidity was not found among countries and/or various regions of the world. Moreover, a minimum number of COVID-19 cases have been confirmed in the temperate regions compared to regions/countries compared to regions/countries with relatively low temperature. In conclusion, the SARS-CoV-2 infection has been found in a wide range of temperatures. It might be hypothesized that comparatively elevated air temperature could play a detrimental effect for SARS-CoV-2 spread.

Oil palm is one of the most important crops in Malaysia. Lately, the production of oil palm has been reduced due to a variety of factors, including the weather and climate. Temperature, wind speed, relative humidity, sunshine, and rainfall distribution all have an impact on palm tree growth and development, which in turn has an impact on oil palm production. This paper aims to investigate the effects of some weather elements (temperature, wind speed, relative humidity, sunshine, and rainfall) on oil palm production in Peninsular Malaysia. Data were analyzed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, and multiple linear regression (MLR). The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature, sunshine, wind speed, relative humidity, and rainfall (independent variables). The findings revealed that temperature, wind speed, relative humidity, sunshine, and rainfall have a low impact on oil palm production and yield turnover. The R2 value of 0.202 shows that the independent variables explained only 20.2% of the fluctuation in palm oil production. The study recommends working within an integrated approach involving scientific research, planting, improving variety, improving regional academic leadership, and engaging private and public stakeholders, emphasized collaborative efforts with researchers in consumer countries, and strengthening the capacity of growers to best agroecological practices.

The aim of this study is to develop an African Neutral Network (ANN) model for predicting temperature and relative humidity in the greenhouse during the calendar year. Input data are ambient temperature and relative humidity outside of the greenhouse chosen for a typical meteorological year for the location of the object and the values of temperature and relative humidity of the air in the greenhouse, obtained as a result of a TRNSYS dynamic simulation of the thermal load of the facility. The goal was to show that our ANN model is capable of making predictions over extended time period. The TRNSYS model was created on a real object, taking into account all relevant parameters, in order to describe the dynamic behavior of the object as good as possible. The ANN model is formed of 3 layers, where the number of neurons in the hidden layer is obtained by training different types in order to reach the optimal number of neurons, and the values of the learning rate and epochs are also varied. The activation functions were respectively the hyperbolic tangent in the hidden layer and the linear function in the output layer. The Root Mean Square Error (RMSE), Mean Absolute Error (MAE) and Correlation Coefficient were chosen as the statistical criteria for measuring of the network performance. MAE and RMSE showed that the model with 6 neurons in the hidden layer gave the best results of data prediction in relation to the input data. Statistical analysis of output shows that, the RMSE and Mean Absolute Error (MAE) between the measured and predicted temperature was 0.3166 °C and 0.1002°, and the relative humidity RMSE and MAE was 5.9% and 3.4%, respectively, which can satisfy the demand of greenhouse climate control. The results of the study showed that the model can be used with satisfactory accuracy to predict the parameters of the internal environment, in relation to the complex simulation of the thermal load of the object.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

SARS-CoV-2 virus infections in humans were first reported in December 2019, the boreal winter. The resulting COVID-19 pandemic was declared by the WHO in March 2020. By July 2020 COVID-19 is present in 213 countries and territories, with over 12 million confirmed cases and over half a million attributed deaths. Knowledge of other viral respiratory diseases suggests that the transmission of SARS-CoV-2 could be modulated by seasonally-varying environmental factors such as temperature and humidity. Many studies on the environmental sensitivity of COVID-19 are appearing online, and some have been published in peer-reviewed journals. Initially, these studies raised the hypothesis that climatic conditions would subdue the viral transmission rate in places entering the boreal summer and that southern hemisphere countries would experience enhanced disease. For the latter, the COVID-19 peak would coincide with the peak of the influenza season, increasing misdiagnosis and placing an additional burden on health systems. In this review, we assess the evidence that environmental drivers are a significant factor in the trajectory of the COVID-19 pandemic, globally and regionally. We critically assessed 42 peer-reviewed and 80 preprint publications that met qualifying criteria. Since the disease has been prevalent for only half a year in the northern, and a quarter of a year in the southern hemisphere, datasets capturing a full seasonal cycle in one locality are not yet available. Analyses based on space-for-time substitutions, i.e. using data from climatically distinct locations as a surrogate for seasonal progression, have been inconclusive. The reported studies present a strong northern bias. Socio-economic conditions peculiar to the ‘Global South’ have been omitted as confounding variables, thereby weakening evidence of environmental signals. We explore why research to date has failed to show convincing evidence for environmental modulation of COVID-19, and discuss directions for future research. We conclude that the evidence thus far suggests a weak modulation effect, currently overwhelmed by the scale and rate of the spread of COVID-19. Seasonally-modulated transmission, if it exists, will be more evident in 2021 and subsequent years.

Panama possesses multiple wetlands designated as protected areas and zones of internationally recognized importance, one amongst them, the Bahía de Panamá wetland Ramsar site, which represents approximately 21% of the national mangrove surface coverage. Due to the major ecological and economic relevance of mangrove ecosystems and their vulnerability to the effects of a changing climate it is considered necessary to perform in situ studies that evaluate the changes in sensitive meteorological parameters. This research was carried out with the objective of measuring air temperature and relative humidity values in a section of the Panama Bay wetland for the 2017-2018 period. This section, neighboring urban development projects, houses since the year 2015 the first tower for determining eddy covariance and measuring micrometeorological parameters in mangrove forests in Panama. We determined monthly and yearly mean values for the studied variables and determined the correlation between them with the use of Pearson’s correlation coefficient. Results show that both parameters still remain at tolerable levels for this type of ecosystems, with both years having very similar annual mean temperatures (27.47 ± 0.32°C for 2017 and 27.48 ± 0.67°C for 2018) and the annual mean relative humidity for 2018, being 85.35%.

Global warming has been increasing heat stress threat in animals which can be monitored by Temperature Humidity Index (THI). The present study describes the relationship of THI, calculated using 35 years period weather station data, and production performances of dairy cattle in a se-lected area of Bangladesh. The month January and June were identified as the coolest and hottest, respectively. Based on this outcome, every year in the month of January and June production performances of 10 crossbred cows with homogenous characteristics were monitored for a period of 5 years. The average THIMEAN value was found 17% higher in June as compared to January, and with this increment of THIMEAN average milk production was decreased 24.4% (p<0.05). The milk fat and protein content were also reduced (p<0.05) by 14.5 and 15.2%, respectively suggesting negative correlation as like as milk production. However, ash content was increased 15.3% that indicates a positive correlation. In addition, multiple regression analysis revealed each point increase in THIMEAN and rectal temperature, there was a decrease in milk yield 0.04 and 1.17 kg ECM, respectively. In contrary, each point increase in THIMEAN resulted 0.059 C increase of rectal temperature. Taken together, THIMEAN value calculated using metrological station data has distinct relationship with the production performances of lactating crossbred dairy cows.

The present study investigated the effect of different ambient temperature and relative humidity (RH) but equal temperature-humidity index (THI) on laying performance, egg quality, heterophil to lymphocyte ratio (H/L ratio), corticosterone (CORT) concentration in blood, yolk and albumen, and plasma biochemical parameters in laying hens. One hundred and twenty commercial hens (Hy-Line Brown) aged 60 weeks were allocated into 2 environmental chambers. Laying hens were subjected to either one of two thermal treatments, i.e., 26ºC and 70% RH (LH75) and 30ºC and 30% RH (HL75) for 28 days. Both thermal treatments had equal THI being 75. Neither LH75 nor HL75 affected (P > 0.05) laying performance including egg production, egg weight, egg mass, feed intake, and feed conversion ratio. Plasma biochemical parameters such as total cholesterol, high-density lipoprotein cholesterol, triglyceride, calcium, magnesium, and phosphorus was not altered (P > 0.05) by thermal treatments. As to the stress indicators, both environment regimes failed (P > 0.05) to affect blood H/L ratio and CORT levels in plasma, yolk and albumen although albumen CORT levels were elevated (P < 0.05) in LH75 vs. HL75 at days 3, 7, and 28. In conclusion, our study suggests that laying hens performed and responded equally when they were exposed to equal THI environment conditioned from either 26ºC and 70% RH or 30ºC and 30% RH. The results of this study will be served as a scientific basis for management decisions and handling under thermally challenging conditions.

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

The construction field uses up over one-third of the global energy consumption and contribute to 40% of CO2 emissions according to the International Energy Agency (IEA) and the 2020 annual reporter of United Nation, Goal 11 (Make cities inclusive, safe, resilient and sustainable) which discusses sustainable, safe and efficient buildings. Therefore, Morocco has a commitment to this program by publishing the law 47-09 of energy efficiency. This work aims to study the energy efficiency of two types of building, a conventional and a natural building. Conventional building is constructed using concrete, while the natural one uses sand clay and straws. As for the technique of making the natural building, it perpetually follows the same approach accustomed in rural zones of Atlas Mountains in Morocco. In this research we also simulate, temperature and humidity variation inside these buildings using TRNSYS software. Sketch Up software was employed to design these houses. The weather database is used for a typical meteorological year (TMY). In the case of natural building, many building configurations were simulated: roof insulation, floor insulation, different types of glazing and sun protection. What's more, the thermal comfort is revealed to be more conspicuous in the case of natural building.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

Regional Climatic Comfort Index (CCI) deteriorated significantly due to the climate change and anthropogenic interference. Knowledge regarding the long-term temporal dynamics of CCI in typical regions should be strengthened. In this study, we analyze the temporal and spatial evolution of CCI from 1969 to 2018 in Guangdong Province, based on meteorological indicators, including heat, humidity, wind and cloth loading etc.. Additionally, the population exposure to climate unconformity was examined since 1990 with the help of population data. Our study found that: (1) the warming and humidifying of the summer climate served as the main driving force for the continuous deterioration of CCI, with the comfortable days decreased by 1.06d/10a and the extremely muggy days increased by 2.83d/10a; (2) spatially, the lowest climate comfortability concentrated in southwestern Guangdong with more than 50 uncomfortable days each year, while the climate comfortability in northeastern Guangdong tends to deteriorated whit higher rate, which can reach as high as 6d/10a; (3) in summer, the population exposure to uncomfortable climate highly centralized in the Pearl River Delta, Shantou, Jieyang, and the surrounding areas, and both area and population exposure showed increasing trends. Particularly, Shenzhen held the highest growth rate of population exposure with an increase rate of 2.94 million/10a; (4) although the discomfort distribution and deterioration rate vary across the province, the spatial heterogeneity of comfortability is diminishing in Guangdong Province. This study will provide scientific reference for regional urban planning, thermal environment improvement, local resident health risk analysis, and key strategy implementation, etc.

The United Arab Emirates (UAE) is significantly dependent on desalinated water and groundwater resource, which is expensive and highly energy intensive. Despite the scarce water resource, only 54% of the recycled water was reused in 2015. In this study, an “Oasis” complex comprised of Sustainable Farming Compartments (SFCs) was proposed for reusing treated wastewater to decrease the ambient temperature of the SFC via an evaporative cooling system. A prototype SFC with half the original scale (width = 1.8 m, depth = 1.5 m, front height = 1.2 m back height = 0.9 m) was designed, built, and tested in an environmentally controlled laboratory and field site to evaluate the feasibility and effectiveness of the SFC under the climatic conditions in Abu Dhabi. Based on the experimental results, the temperature drops obtained from the SFC in the laboratory and field site were 5 ̊C at initial relative humidity of 60% and 7- 15 ̊C at initial relative humidity of 50%, respectively. An energy simulation using dynamic numerical simulations was performed in comparison to the results of the experiment. The energy-based dynamic simulation shows good agreement with the experimental results. The total power consumption of the SFC system was approximately three and a half times lower than that of an electrical air conditioner.

With the increasing pace of global warming, it is important to understand the role of meteorological factors in influenza virus (IV) epidemics. In this study, we investigated the impact of temperature, UV index, humidity, wind speed, atmospheric pressure, and precipitation on IV activity in Norway, Sweden, Finland, Estonia, Latvia and Lithuania during 2010-2018. Both correlation and machine learning analyses revealed that low temperature and low UV indexes were the most predictive meteorological factors for IV epidemics in the Northern European countries. Our in vitro experiments confirmed that low temperature and UV radiation preserved IV infectivity. Associations between these meteorological factors and IV activity could improve surveillance and promote development of accurate predictive models for future influenza outbreaks in Northern Europe.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

Seasonal changes and varying degree of corneal hydration has been linked to excimer laser corneal ablation rates. Use of PMMA as calibration material in refractive lasers is well established. However, PMMA ablation may be equally affected by seasonal variations in temperature and humidity, intern affecting the calibration process. Aim of this work is to analyze the effect of seasonal changes in PMMA Performance using SCHWIND AMARIS laser system. PET and PMMA ablations conducted in climate-controlled environment with 826 consecutive AMARIS systems manufactured over 6 years were retrospectively analyzed. Lasers were stratified depending on seasons and months of the year. Metrics like Single laser pulse fluence, nominal number of laser pulses, mean performance, standard deviation, and technical performance of system were compared to global average values. Cyclic winter-summer variation was confirmed with seasons winter and summer showing statistically significant variations with respect to global values. Metric technical performance showed deeper PMMA ablation performance in summertime, with maximum seasonal deviation of 6%. Results were consistently confirmed in seasonal as well as monthly analyses. These findings could help minimize variance among laser systems by implementing compensation factors depending on seasons such that laser systems installed worldwide follow the same trend line of variation.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

The urban heat island (UHI) is mostly due to urbanization. This phenomenon in concert with the high temperatures caused by global climate change may profoundly affect human thermal comfort, which can influence human productivity and morbidity especially in spring/summer period. The main objective of this investigation was to determine changes in degree of thermal comfort of Mexico City’s inhabitants and compare it with the physiological equivalent temperature (PET) to evaluate whether PET and its categorization are adequate to be applied in Mexico City. A series of microclimatological measurements to estimate PET were made in four sites including the city´s center. Concomitantly, a series of surveys of thermal perception were applied to 1300 passersby. The results show that PET has increased from 1990 to 2020 from 0.1208 °C/year to 0.1498 °C/year in the study sites, besides overestimating the degree of thermal comfort of people according to the stablished categories or classes. It is concluded that it is necessary to adjust thermal stress categories. Knowing the percentage of people without thermal comfort will lead us to determine different ranges in environmental parameters to define an acceptable environment for most people.

We used ab initio molecular dynamics simulations to compare the activation of 2-propanol on the low index Co3O4 (111), (110) and (001) surfaces in dry conditions. The thermal and surface assisted decomposition of a film of 2-propanol to 2-propoxide on the B-termination of each surface was monitored and analyzed. The investigations suggest an activity order of Co3O4 (111) > (110) > (001). On the B-terminated (111) surface, full dissociation of all 2-propanol molecules at the interface is observed, accompanied by a Mars-van Krevelen-type mechanism upon hydroxylation of the surface. On the (110) surface, 2-propanol dissociation is driven by temperature, which activates the two-fold coordinatively unsaturated surface oxygens. The (001) surface on which almost no dissociation occurs is the least active. No formation of acetone is observed in the simulations conditions.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Plums are primarily marketed for fresh consumption, canning, freezing, jam and jelly. Unfortunately, plum consumption has remained steady or declined. Consumers complain about a lack of flavor quality but are willing to pay for higher quality. Thus, lack of flavor and cold storage disorders are the main barriers to consumption. Plum cultivars are susceptible to gel breakdown, flesh browning and ‘off flavors’. Consumer acceptance and postharvest life are highly dependent on genotype, quality attributes, harvest date and proper postharvest handling. A consumer quality index (CQI) based on soluble solids concentration (SSC) and minimum firmness is proposed to maximize flavor and postharvest life. In most cases, late harvest increases quality attributes. Our work and industry experience demonstrated that using critical bruising thresholds (CBT) based on minimum firmness measured at harvest acts as a reliable predictor of how late to harvest safely for maximum visual and sensory quality. Plums are well adapted to late harvest because of their low susceptibility to bruising damage, but proper postharvest temperature management and marketing within the potential market life are necessary to maintain flavor and avoid the onset of storage disorders. Thus, to maximize flavor and postharvest life, a CQI based on SSC and minimum firmness measured at consumption is proposed. This article provides guidance on using this CQI, combined with proper postharvest handling techniques such as correct harvest date determination and temperature management, to maintain quality and increase consumption.

The Microwave Humidity and Temperature sounder (MWHTS) on board the Fengyun (FY)-3C satellite measure the outgoing radiance form the Earth surface and atmospheric constituents. MWHTS makes measurements in the isolated oxygen absorption line near 118 GHz and the vicinity of strong water vapor line around 183 GHz, can provide fine vertical distribution structure of both atmospheric humidity and temperature. However, in order to obtain the accurate soundings of humidity and temperature by the physical retrieval method, bias between the observed radiance and those simulated by radiative transfer model from the background or first guess profiles must be correct. In this study, two bias correction methods are developed through the correlation analysis between MWHTS measurements and air mass identified by the first guess profiles of the physical inversion, one is the linear regression correction (LRC) and the other is neural networks correction (NNC), representing the linear and nonlinear nature between MWHTS measurements and air mass, respectively. Both correction methods have been applied to MWHTS observed brightness temperatures over the geographic area (180° W-180° E, 60° S-60° N). The corrected results are evaluated by the probability density function of the difference between corrected observations and simulated values and the root mean square error (RMSE) with respect to simulated observations. The numerical results show that the NNC method perform better, especially in MWHTS channels 1 and 7-9 whose peak weight function heights are close to the surface. In order to assess the effects of bias correction methods proposed in this study on the retrieval accuracy, a one-dimensional variational system was built and applied to the MWHTS uncorrected and corrected brightness temperatures to estimated atmospheric temperature and humidity profiles, The retrieval results show that the NNC has better performance which is to be expected. An indication of the stability and robustness of NNC method is given which suggests that the NNC method has promising application perspectives in the physical retrieval.

The identified Urban Heat Island (UHI) phenomenon, coupled with diminished vegetation and anthropogenic heat release, poses a significant environmental challenge for major urban centers. Particularly worrisome is the UHI effect in hot and temperate climates such as the Mediterranean region during the summer season. This exacerbates discomfort and heightens the risks of diseases linked to high temperatures. Additionally, it contributes to environmental consequences, including elevated electricity consumption due to increased demand for cooling [1]. The utilization of Remotely Sensed imagery for estimating Land Surface Temperature has become more prevalent in various applications associated with evaluating urban micro-climates and the Urban Heat Island (UHI) phenomenon. This study presents an algorithm for the automatic mapping of Land Surface Temperature (LST) from Landsat-8 data using a vegetation index-based technique in the Google Earth Engine (GEE) platform. The primary aim is to discern patterns and trends in LST over a 5-year period, from 2017 to 2021. The application was tested in the urban area of Thessaloniki, Northern Greece, which is particularly representative of the Mediterranean urban environment. Computation of Normalized Difference Indices (NDVI, NDBI, NDWI) for the study area was also performed within the GEE platform and correlation analysis was implemented to evaluate the impact of the urban landscape on the distribution of LST.

Eichornia crassipes is one of the most dangerous aquatic weeds for Lake Tana and other water Bodies of Ethiopia .Use of natural enemies of the weed to discourage its propagation and impact is one of the best recommended options by scientific society.Among them, there are more fungi naturally a pathogen for water hyacinth and other plants. To use those pathogens to manage the highly water hyacinth infestation area of Lake Tana specfically Gondar Zuria woreda , Lemeba Kebela , infected water hyacinth plant material by fungi were collected from Goregora side of Lake Tana. The collection was done from infected water hyacinth leaves by fungi.All isolated fungi(Zygomycota .,Candidaalbicanaa,Trichoderma ,Aspergillus flavus, Fusarium s,Aspergillus niger,Pencillium and Rhizocotosolani spp) were attempted to infect the healthy water hyacinth in Lemeba Kebela by spraying 2ooo ml cultured mixed fungi in 20 metre square areas and after three weeks of exprement the fungi were severely affected the weeds and expanded in all wetland areas of lemba kebala that infested by water hyacinth but in some exprement areas the leaf of water hyacinth show disease symptoms after 7 days of fungi releasd on targeted area.This observational research shows that the fungi were high potential to attack healthy water hyacinth at high enviroment temprature and at less humidity

In this research paper an algorithm for the derivation of methods based on theorems and axioms of fuzzy logic is presented, analyzed and applied. This new proposed procedure generates fuzzy methods and evaluates the value of fuzzy propositions through fuzzy implication. The new implications of the family should satisfy a number of axioms. Also, we denote the conditions in order to satisfy the maximum number of axioms. Moreover, authors state and prove theorems focusing on fuzzy implication, observing the rule: the fuzzy function of fuzzy implication is strong and that lead to fuzzy negation. In addition, the optimal number of repetitions is calculated according to the expected truth value. The formulas produced are verified through the use of temperature and humidity values over a certain period of time and in a certain geographical area in Greece. The basic steps of the methodology are the fuzzification of the data given ​​using four membership degree functions and the application of the membership degrees of temperature and humidity values on a new type of fuzzy implication. Finally, we observed that the isosceles trapezium gave the best results and the type of fuzzy implication can be effectively applied.

Mangrove vegetation plays a vital role in habitat and nursing ground for different organisms and prevents coastal erosion caused by wave and tide action. In recent years the mangrove vegetation in Chattogram coast, Bangladesh, has been interrupted by other infrastructural development, which has a destructing effect on the surrounding environment. Land surface temperature analysis of an area helps learn about different environmental conditions, weather, and climate. It is also essential to monitor the rising temperature and global warming, the biggest threat to humanity. NDBI and NDVI are the efficient process for monitoring vegetation and build up areas of a geographical location. This study focused on those analyses to understand the importance of mangrove vegetation in the Salimpur area and surrounding coastal areas of Chattogram by studying the relationship between NDVI and NDBI, NDVI and LST, NDBI, and LST. The outcome indicates that a higher vegetation index results in lower land surface temperature during different periods, negatively correlated. This study also found a strong positive correlation between buildup index (NDBI) and land surface temperature (LST), which means Land Surface temperature was found higher in Buildup areas. The vegetation areas are greatly affected by the buildup areas. The correlation between buildup areas and vegetation areas was strongly negative, which means an increase of NDBI decreases NDVI, and a decrease of NDBI increases NDVI.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

To understand lung damage caused by COVID-19, we deduced two-phase lung damage mechanisms. After the lungs are infected with SARS-CoV-2 virus, the affected lung tissue swells and surface properties of pulmonary capillaries change, resulting in an increased flow resistance of affected capillaries. If a sufficient number of capillaries are affected by the infection, the swelling and increased cell wall adhesion collectively raise pulmonary vascular resistance. The increased vascular resistance further increases the dwell times of WBCs in affected capillaries and nearly capillaries. When pulmonary pressure is sufficiently higher, WBCs are forced to squeeze into interstitial spaces or alveolar spaces when local pressures are higher than what the capillaries can withstand. When more and more WBCs are dynamically retained, the flow resistance of more capillaries rises, pulmonary vascular resistance rises, and pulmonary pressure rises. The rise in the pulmonary pressure in turn results in elevated capillary pressures. When capillary pressures around the alveoli are sufficiently high, they cause interstitial pressures to change from normally negative values to positive values. The positive pressures cause fluid leakage to the alveolar space and thus degrade lung function. Tissue swelling, and occupation of WBCs in interstitial spaces and alveolar spaces further reduce compressible volume, and thus cause further rise in the pulmonary vascular resistance and pulmonary pressure. When the pulmonary pressure has reached a critical point as in the second phase, the blood breaks capillary walls and squeezes through interstitial spaces to reach alveolar spaces, resulting in irreversible lung damages. The available free volume in the thorax cage, organ usable capacities, temperature and humid are expected to have great impacts on degree of lung damages. The free volume in the thorax cage, lung usable surplus capacity, and other organ usable capacities determine the arrival time of last-phase irreversible damage. The mechanisms imply that the top priority for protecting lungs is maintaining pulmonary micro-circulation and preserving organ functions in the entire disease course while controlling viral reproduction should be stressed in the earliest time possible. The mechanisms also explain leukecytes are recruited and migrated into inflamed tissues by increasing their dwell times caused by increased local flow resistance.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

Satellite-based monitoring can retrieve ground-level PM_2.5 concentrations with higher-resolution and continuous spatial coverage to assist in making management strategies and estimating health exposures. The Sichuan Basin has a complex terrain and several city clusters that differ from other regions in China: it has an enclosed air basin with a unique planetary boundary layer dynamic which accumulates air pollution. The spatiotemporal distribution of 1-km resolution Aerosol Optical Depth (AOD) in the Sichuan Basin was retrieved using the improved dark pixel method and Moderate Resolution Imaging Spectroradiometer (MODIS) data in this study. The retrieved seasonal AOD reached its highest values in spring and had the lowest values in autumn. The higher correlation (r = 0.84, N = 171) between the ground-based Lidar AOD and 1-km resolution MODIS AOD indicated that the high-resolution MODIS AOD could be used to retrieve the ground-level PM_2.5 concentration. The Lidar-measured annual average extinction coefficient increased linearly with the Planetary Boundary Layer Height (PBLH) in the range of 100 ~ 670 m, but exponentially decreased between the heights of 670 ~ 1800 m. Both the correlation and the variation tendency of simulated PBLH from WRF_SHIN/CALMET were closer to the Lidar observation than that of three other Planetary Boundary Layer (PBL) schemes (the Grenier-Bretherton-McCaa (GBM) scheme, the he Total Energy-Mass Flux (TEMF) scheme and the University of Washington (UW) scheme), which suggested that the simulated PBLH could be used in the vertical correction of retrieval PM_2.5. Four seasonal fitting functions were also obtained for further humidity correction. The correlation coefficient between the aerosol extinction coefficient and the fitted surface-level PM_2.5 concentration at the benchmark station of Southwest Jiao-tong University was enhanced significantly from 0.62 to 0.76 after vertical and humidity corrections during a whole year. During the evaluation of the retrieved ground-level PM_2.5 with observed values from three cities, Yibin (YB), Dazhou (DZ), and Deyang (DY), our algorithm performed well, resulting in higher correlation coefficients of 0.78 (N = 177), 0.77 (N = 178), and 0.81 (N = 181), respectively.

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

This study investigates the possible mechanisms related to the wide range of relative humidity in cirrus clouds (RHi). Under the closed adiabatic assumption, the impacts of vertical motion and ice crystal deposition/sublimation on RHi are investigated through in situ observations and parcel model simulations. Vertical motion is an active external force that changes the RHi, and ice crystal deposition/sublimation plays a role in mitigating the change in RHi. They are the two most important mechanisms involved in controlling the RHi fluctuation during cirrus evolution and could well explain the wide range of RHi in wave-related cirrus clouds. Furthermore, a comparison of cloud statistical characteristics from both observations and simulations shows that a very low value (e.g., 0.001) for the water vapor ice deposition coefficient is highly unlikely.

Near-surface humidity (Qa) is a key parameter that modulates oceanic evaporation and influences the global water cycle. Remote sensing observations act as feasible sources for long-term and large-scale Qa monitoring. However, existing satellite Qa retrieval models are subject to apparent uncertainties due to model errors and insufficient training data. Based on in situ observations collected over the China Seas over the last two decades, a deep learning approach named Ensemble Mean of Target deep neural networks (EMTnet) was proposed to improve the satellite Qa retrieval over the China Seas for the first time. The EMTnet model outperforms five representative existing models by nearly eliminating the mean bias and significantly reducing the root-mean-square error in satellite Qa retrieval. According to its target deep neural networks selection process, the EMTnet model can obtain more objective learning results when the observational data are divergent. The EMTnet model was subsequently applied to produce a 30-year monthly gridded Qa data over the China Seas. It indicates that the climbing rate of Qa over the China Seas under the background of global warming are probably underestimated by current products.

The dependence of the critical temperature $T_c$ of high-temperature superconductors of various families on their composition and structure is proposed. A clear dependence of the critical temperature of high-temperature superconductors (hydrides, Hg- and Y-based cuprates) on the serial number of the constituent elements, their valence and crystal lattice structure has been revealed. For cuprates, it is shown that it is possible to obtain even higher temperatures of superconducting transitions at normal pressure by implanting mercury atoms into the crystal lattice of cuprate.

Rising humidity in old and historical buildings is a current issue that affects their structure, due to water capillarity and its propagation inside the walls, a key factor in heritage preserving and its functionality. It is also responsible for materials degradation exposed to frost and defrost cycles, biodegradation and salt crystallization. Moisture also increases the heating costs of the affected buildings, due to high thermal conductivity of the moist masonries. The paper presents an unconventional method for humidity removal or stabilisation due to infiltration of capillary water into the masonries, using electromagnetic waves systems that result in changing the water polarity inside the affected walls and pushing it out of the construction. The system consist of a small box, connected to the power supply, installed inside the building, remaining on the same location throughout the entire life of the construction. By means of this procedure, not only do the walls of the structure stay moisture-free, but also the foundations and the surrounding soil. Through this process, not only the walls of the construction remains dry, but also the foundations and the soil around them. The electromagnetic wave method was applied on five different historical buildings, located in Romania, Cluj Napoca’s historical centre, in the vicinity of Somes river, with rising damp due to water capillarity. Measurements were conducted at every six months after the system installation, for a period of minimum 24 months, using the same marked locations, at a depth of 5 cm in the walls. All buildings studied are made of stone and stone with plain brick, with different chemical, type, pore direction and porosity characteristics. The measured values show in most cases, a clear decrease of wall humidity levels or a stagnation of the capillarity rise in the monitored walls, after a minimum of 24 months after the system installation. The electromagnetic wave system, as a non-destructive method, can be applied to cases with no accidental water source or high raised groundwater, for historical buildings where no exterior works are possible or interior invasive interventions.

Zeolitic imidazolate frameworks (ZIFs) have potential for various gas and ion separations due to their well-defined pore structure and relatively easy fabrication process compared to other metal-organic frameworks. As a result, many reports have focused on preparing polycrystalline and continuous ZIF layers on porous supports. In this study, we investigated how humidity and chamber temperature influence the structure of a ZIF-8 layer prepared by the hydrothermal method. We controlled the chamber temperature (ranging from 50 °C to 70 °C) and relative humidity (ranging from 20 % to 100 %) using a thermos-hygrostat chamber. We found that as the chamber temperature increased, ZIF-8 preferentially grew into particles rather than forming a continuous polycrystalline layer. By measuring the temperature of the reacting solution based on chamber humidity, we discovered that the heating rate of the reacting solution varied with humidity, even at the same chamber temperature. At higher humidity, thermal energy transfer was accelerated as water vapor delivered more energy to the reacting solution. Therefore, a continuous ZIF-8 layer could be formed more easily at low humidity ranges (ranging from 20 % to 40 %), while micron ZIF-8 particles were synthesized at a high heating rate. Our findings suggest that controlling the heating rate of the reacting solution is critical to preparing a continuous ZIF-8 layer, particularly for future scale-up of ZIF-8 membranes.

The main parameters for calculation of relative humidity are the wet-bulb depression and dry bulb temperature. In this work, easy-to-used predictive tools based on statistical learning concepts, i.e., the Adaptive Network-Based Fuzzy Inference System (ANFIS) and Least Square Support Vector Machine (LSSVM) are developed for calculating relative humidity in terms of wet bulb depression and dry bulb temperature. To evaluate the aforementioned models, some statistical analyses have been done between the actual and estimated data points. Results obtained from the present models showed their capabilities to calculate relative humidity for divers values of dry bulb temperatures and also wet-bulb depression. The obtained values of MSE and MRE were 0.132 and 0.931, 0.193 and 1.291 for the LSSVM and ANFIS approaches respectively. These developed tools are user-friend and can be of massive value for scientists especially, those dealing with air conditioning and wet cooling towers systems to have a noble check of the relative humidity in terms of wet bulb depression and dry bulb temperatures.

Oriental melons have a relatively short shelf life as they are harvested during the summer season and susceptible to cold-induced injuries. Typical chilling injury when stored at 4℃ is expressed as browning of the fruit suture. To prolong the shelf life and reduce browning of the fruit, the effects of modified atmosphere packaging (MAP), X-tend modified atmosphere (MA)/modified humidity (MH) bulk packaging (XF), and polyethylene (PE) packaging, on oriental melons were investigated during storage at 4℃ and 10℃ for 14 days and under retail display conditions at 20℃. The O2 concentrations in PE packages stored at 4℃ and 10℃ ranged from 17.4–18.5%, whereas those in XF packages were reduced to 16.3–16.6%. The CO2 content of XF package (4.2–4.6%) was higher than that of PE package (1.4–1.9%) stored at 4℃ or 10℃. Relative humidity (RH) saturated in the PE packages but not in the XF packages after seven days of storage. Furthermore, PE packages performed better at maintaining melon weight and firmness than XF packages during storage at 10℃ for 14 days and under retail display conditions at 20℃. PE and XF packages effectively reduced the browning index of the peel and white linear sutures of oriental melons compared with the unpackaged control during cold storage at 4℃, and this observation was maintained at the retail display condition at 20℃. The enhanced CO2 levels, reduced O2 levels, and optimal RH values that were provided by the MAP, prevented the browning symptoms and improved the marketability and shelf life of oriental melons.

The main goal of this article is to demonstrate the impact of environmental data on the spreading of Covid-19. In this research, data has been collected from 70 cities/provinces that are affected by Covid-19. Here, environmental data refers to temperatures, humidity and population density in each of these cities/provinces. This data has been analyzed using statistical models such as Poisson, Quasi-Poisson and negative Binomial. It is found that a negative Binomial regression model is the best fit for our data. Our results reveal that average high temperature is the vital factor to slow down the spread of Covid-19. In addition, higher population density found to be an important factor for the quick spreading of Covid-19 where it is quite impossible to maintain the social distance and the virus can spread easily.

We present the design, fabrication, and response of a polymer-based Laterally Amplified Chemo-Mechanical (LACM) humidity sensor based on mechanical leveraging and parametric amplification. The device consists of a sense cantilever asymmetrically patterned with a polymer and flanked by two stationary electrodes on the sides. When exposed to a humidity change, the polymer swells after absorbing the analyte and causes the central cantilever to bend laterally towards one side, causing a change in the measured capacitance. The device features an intrinsic gain due to parametric amplification resulting in an enhanced signal-to-noise ratio (SNR). 11-fold magnification in sensor response was observed via voltage biasing of the side electrodes without the use of conventional electronic amplifiers. The sensor showed a repeatable and recoverable capacitance change of 11% when exposed to a change in relative humidity from 25-85%. The dynamic characterization of the device also revealed a response time ~1s and demonstrated a competitive response with respect to a commercially available reference chip.

Following the coronavirus disease 2019 (COVID-19) pandemic, several studies have examined the possibility of correlating the virulence of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the virus that causes COVID-19, to the climatic conditions of the involved sites; however, inconclusive results have been generally obtained. Although either air temperature or humidity cannot be independently correlated with virus viability, a strong relationship between SARS-CoV-2 virulence and the specific enthalpy of moist air appears to exist, as confirmed by extensive data analysis. Given this framework, the present study involves a detailed investigation based on the first 20–30 days of the epidemic before public health interventions in 30 selected Italian provinces with rather different climates, here assumed as being representative of what happened in the country from North to South, of the relationship between COVID-19 distributions and the climatic conditions recorded at each site before the pandemic outbreak. Accordingly, a correlating equation between the incidence rate of the pandemic and the average specific enthalpy of atmospheric air was developed, and an enthalpy-based seasonal virulence risk scale was proposed as a tool to predict the potential danger of COVID-19 spread due to the persistence of weather conditions favorable to SARS-CoV-2 viability. For practical applications, a conclusive risk chart expressed in terms of coupled temperatures and relative humidity (RH) values was provided, showing that safer conditions occur in case of higher RH at the highest temperatures, and of lower RH at the lowest temperatures. The proposed risk scale was in agreement with the available infectivity data in the literature for a number of cities around the world.

Foot lesions are among the most frequent causes of morbidity and disability in the diabetic population. Thus, exploration of means of preventive control are vital for detecting early signs and symptoms of this disease, Infrared thermography has been proven effective in the control of diabetic foot is among the complementary diagnostic tools available for this disease. The last review on this topic was published in 2015 and so, here we conducted a bibliographic review of the main databases (PubMed, the Web of Science, Cochrane library, and Scopus) during the third quarter of 2023. We aimed to identify the effectiveness of infrared thermography as a diagnostic element in pre-ulcerous states in diabetic patients and to detect diabetic foot ulcer complications. We obtained a total of 200 articles, 22 of which were included in this present review; 17 articles had been published after 2017. After analysing the use of infrared Thermography in diabetic patients both with and without ulcers, as well as in healthy individuals, we concluded that is an effective tool for detecting early-stage ulcers in diabetic foot patients.

The development of a remote sensing system is proposed in the present study for monitoring of the electrical resistance of concrete in real time. The sensor is embedded in the concrete bulk, and the data are sent via a gateway to a computer for the data analysis. The sensibility of the sensors to the effect of the presence of a crystalline admixture has been also assessed in the study. Different cycles of drying and water penetration have been considered to assess the sensor performance in different water content conditions. Sensors have shown to capable of detecting changes in electrical resistance when humidity changes. The sensitive of the sensors to the action of waterproofing admixtures in the mortar has been also confirmed. The contribution of the temperature plays a critical role on the sensor response, and its simultaneous monitoring is recommended.

This paper addresses the effect of both microstructure and relative humidity on the long-term creep properties of sustainable calcium carbonate (CaCO₃) cements. Those can be prepared by mixing amorphous calcium carbonate and vaterite with water. A larger starting amount of vaterite, X_V, within the mixture design gives a higher elasticity and resistance to the specimens due to the larger overall bridging area within the newly formed calcite crystals. Regarding creep properties for a given relative humidity, the amplitude of creep strain decreases with X_V, and makes the relation between the elastic modulus, E, and hardness, H, of the samples to be linear with the contact creep modulus, C. On the other hand, for a given composition, the amplitude of creep increases with the relative humidity, making the contact creep modulus, Ci, to rise exponentially with the elastic modulus, E, and hardness, H, of the specimens. The most probable creep mechanisms for this kind of cement seem to be a combination of microcraking in the early stages and dissolution and reprecipitation of calcite in the long-term (also known as pressure solution theory). The presence of water in pores with increasing relative humidity might enhance the local dissolution of calcite, and hence the creep amplitude.

A semi-analytical approach is developed for predicting pyrolysis front temperature in a solid undergoing thermal decomposition. The pre-reaction heating stage is described using an analytical formulation and invoking the concept of thermal penetration depth. The solution for the solid conversion stage accounts for decomposition enthalpy, convective flow of volatiles, and a reaction front characterized by a uniform temperature that progresses toward the inner layers. This method incorporates empirical relations into the analytical model. Two scenarios are considered. First, the solution of the pyrolysis model combined with the data of conversion time versus external heat flux leads to an algebraic expression that reveals the existence of a maximum pyrolysis-front temperature. Explicit relations are derived for both the extremum pyrolysis temperature and optimum applied heat flux. In the second case, an expression is derived for the ignition temperature of a solid fuel by incorporating ignition delay time measurements into the heating stage model. The newly derived expression allows to describe the ignition temperature as a function of the Biot number and external heat flux. The relation obtained for the ignition temperature explains the experimental trends reported in some previous studies where two local extremums were observed for the ignition temperature in the absence of volatiles reactions.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorm, dust or sand, insects’ collisions, increased humidity and sea spray, result in degraded aerodynamic performance. The outcome of the most studies is that lift is degraded and at the same time drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of the crucial aspects to take into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic performance of horizontal axis wind turbines.

Geological disposal facilities for radioactive waste pose significant challenges for robust monitoring of environmental conditions within the engineered barriers that surround the waste canister. Temperatures are elevated, due to the presence of heat generating waste, relative humidity varies from 20% to 100%, and swelling pressures within the bentonite barrier can typically be 2-10 MPa. Here, we test the robustness of a bespoke design MEMS sensor-based monitoring system, which we encapsulate in polyurethane resin. We place the sensor within an oedometer cell and show that despite a rise in swelling pressure to 2 MPa, our relative humidity (RH) measurements are unaffected. We then test the sensing system against a traditional RH sensor, using saturated bentonite with a range of RH values between 50% and 100%. Measurements differ, on average, by 2.87% RH, and are particularly far apart for values of RH greater than 98%. However, bespoke calibration of the MEMS sensing system using saturated solutions of known RH, reduces the measurement difference to an average of 1.97% RH, greatly increasing the accuracy for RH values close to 100%.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

We use the Stefan-Boltzmann law to derive and investigate what we will call the black hole CMB temperature luminosity. Interestingly, the CMB luminosity is always the same for every black hole at a luminosity distance equal to the Schwarzschild radius, which is fully valid in black hole cosmology, a topic that is actively discussed to this day. The CMB black hole luminosity is always the same , regardless of the mass of the black hole. This is in contrast to the Bekenstein-Hawking luminosity, which is linked to the Hawking temperature, that is mass dependent.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Solid-state fermentation (SSF) is the bioprocess where microorganisms are cultivated in the absence of free water under control conditions. Lactic acid can be produced by fermenting grape stalks with Rhizopus oryzae in SSF. During the microorganism growth, the temperature and water content of the solid bed fluctuate, leading to areas of either dry or excessive moisture in the solid substrate. Therefore, it's crucial to control the supply of water to the matrix. In this work, we obtain lactic acid through SSF of grape stalks using Rhizopus oryzae NCIM 1299. The SSF was conducted at a fixed temperature of 35 °C, with three constant relative humidity levels: 50, 65, and 80 %RH. Mathematical models, including the Logistic and First Order Plus Dead Time models for fungal biomass growth and the Luedeking and Piret with Delay Time model for lactic acid production, were adjusted to kinetic curves. Growth kinetic parameters (Xmax, μmax, Tp, T0, Yp/x and td) were determined for all conditions. These kinetic parameters were then correlated with relative humidity using a second-degree polynomial relationship. We observed a decrease in Xmax with increasing %RH, while the value of Yp/x increased at higher %RH. Finally, the optimal variable relative humidity profile was obtained by applying the Dynamic Optimization Technique, resulting in a 15.30% increase in lactic acid production.

A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.

Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

Asphalt pavement temperature has several applications, including pavement structural design and evaluation, asphalt mixture design, asphalt binder grade determination and material aging characterization. However, available asphalt pavement temperature prediction models were mostly developed for temperate climatic conditions, outside of the tropics. Before such models are adopted for use in a tropical climate, their applicability must be evaluated. This study evaluated five empirical asphalt pavement temperature prediction models developed by Lukanen et al. [1], Park et al. [2], Diefenderfer et al. [3], Taamneh [4] all in the United States and Asefzadeh et al. [5] in Canada to ascertain their prediction accuracy in tropical climate, using Ghana as a case study. In-situ asphalt pavement temperature data were measured at two sites for eight months: Kumasi and Tamale in the Forest and Savannah climatic zones, respectively. The measured pavement temperature data were statistically compared with predicted temperatures, and it was found that the Park et al. [2] model provided a more accurate pavement temperature prediction in both climatic zones. The other models either over-predicted or under-predicted asphalt pavement temperature with significant error margins. However, there is a need to improve the prediction accuracy of the Park et al. [2] model or a local model developed.

The response of boreal vegetation to global warming has shown a weakening trend over the last three decades. However, in previous studies, models of vegetation activity responses to temperature change have often only considered changes in mean daily temperature (Tmean), with the diurnal temperature range (DTR) being neglected. The goal of this study is to evaluate the temporal trends of the relationships between two temperature factors (Tmean and DTR) and vegetation activity across the boreal regions on both annual and seasonal timescales, by simultaneously employing satellite and climate datasets. We found that the interannual partial correlation between growing season (GS) NDVI and Tmean (RNDVI−Tmean) showed a significant decreasing trend over the last 34 years. At the seasonal scale, RNDVI−Tmean shows a significant upward trend in the spring, while in the summer and autumn, RNDVI−Tmean exhibits a significant downward trend. The temporal trend characteristics of the partial correlation between NDVI and DTR (RNDVI−DTR), at both the GS and seasonal scales, are fully consistent with RNDVI−Tmean. The area with a significant decrease in GS RNDVI−Tmean and RNDVI−DTR accounted for approximately 44.40% and 41.21% of the boreal region with the 17-year moving window, respectively. In stark contrast, the area exhibiting a significant increasing trend in GS RNDVI−Tmean and RNDVI−DTR accounted for only approximately 14.65% and 13.59% of the boreal region with the 17-year moving window, respectively. With respect to the seasonal patterns of RNDVI−Tmean and RNDVI−DTR, the area with a significant upward trend in spring was greater than that with a significant downward trend. Nevertheless, more areas had a significant downward trend of RNDVI−Tmean and RNDVI−DTR in summer and autumn than had a significant upward trend. Overall, our research reveals a weakening trend in the impact of temperature on vegetation activity in the boreal regions, and contributes to a deeper understanding of the vegetation response to global warming.

The objective of the present study is to analyze COVID-19 transmission in specific dampest regions with excess rainfall and recurring fogs. The working hypothesis is that widespread transmission of SARS CoV 2 (leading to COVID-19) and similar viral agents can be explained by specific climate factors having high air humidity. The main case study of the Turkish Black Sea region is investigated. Results reveal that the provinces in region under study have some climate factors and geographical features that foster the accelerated transmission of viral agents, such as SARS-CoV-2, and consequential negative impact on society. In particular, Spearman's Correlation Coefficient shows a statistically significant positive association between the average atmospheric pressure and the spread of the COVID-19 confirmed cases in Samsun province (Spearman’s correlation coefficient rs =0.86, p-value 0.05). A statistically significant positive association between the average precipitation and the spread of COVID-19 confirmed cases in Sinop province (Spearman’s correlation coefficient rs =0.79, p-value 0.05), and finally, a statistically significant negative association between the average sun hour and the spread of the COVID-19 confirmed cases in Samsun province (Spearman’s correlation coefficient rs = 0.89, p-value 0.01). These findings suggest that regions' geographical characteristics, demographic structure, climate and environmental parameters must be considered in the national scale epidemic management plans to design effective anti-pandemic health policies to cope with future waves of the COVID-19 and new airborne diseases and to reduce negative effects on health, social and economic systems.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

There is increasing evidence that rising temperatures and heatwaves in the United Kingdom are associated with an increase in heat-related mortality. This study aims to retrospectively quantify the impact of heatwaves on mortality during the 2019 summer period using daily death occurrences. Second, it compares excess mortality during the 2019 heatwaves to excess mortality during the 2018 and 2017 heatwave periods. Lastly, it compares the excess mortality in the 2017-2019 heatwaves to the estimated excess deaths for the same period in the Public Health England (PHE) Heatwave mortality monitoring Reports. The cumulative number of excess deaths during the summer 2019 heatwaves were minimal and were substantially lower than during the summer 2018 heatwaves (1,700 deaths) and summer 2017 heatwaves (1,489 deaths). All findings were at variance with the PHE Heatwave mortality monitoring reports which estimated cumulative excess deaths to be 892, 863 and 778 during the summer period of 2019, 2018 and 2017 respectively using provisional death registrations. Issues have been identified in the use of provisional death registrations for mortality monitoring and the reduced reliability of the ONS daily death occurrence database before 2019. These findings may identify more reliable ways to monitor heat mortality during heatwaves in the future.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

The aim of the study was to evaluate the influence of transduser design and its elements, and their materials on temperature in deeper layers of tissues measurement results. A digital modeling was performed to evaluate the influence of the properties of transduser design elements. Experimental research was carried out. Revealed that the accuracy, similar to that of an invasive method using needle probes, can be achieved by measuring the temperature in deeper muscle layers using the proposed transducer.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature elevations in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear correlation of the data were estimated on 0.47oC for the 20 years between 1995 and 2015; the study showed that 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming. For the local influences some practical mitigation actions are proposed, related to improve the energy management and paying more attention to the temperature changes trough improvements in the number and capability of sampling stations in the urban air and in the river, which serve as clear indicators of the changes and the effect of any mitigation measures.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature raises in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear tendencies, were estimated on 0.47ºC for the 20 years between 1995 and 2015; 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming.

This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

The understanding of structural alteration mechanisms due to relative humidity impact on organic supports of paintings is of crucial significance for the preventive conservation strategies in order to ensure the long-term preservation of important cultural identity artworks. The effort in this paper is to simulate Museum realistic relative humidity condition in a climate chamber while monitoring the structural responses through a quantitative interferometric method allowing the quantitative correlation between the physical values of deformation and mass alteration relevant to relative humidity fluctuations.

A planar microwave sensor devoted to the detection of humidity in underwear and clothes in general is proposed. The ultimate goal of the sensor is to detect the presence of liquids in fabrics, of interest to aid patients that suffer from certain pathologies, such as hyperhidrosis and enuresis. The main target in the design of the sensor, considering the envisaged application, is simplicity. Thus, the sensor operates at a single frequency, and the working principle is the variation in the mag-nitude of the transmission coefficient of a matched line loaded with an open-ended quar-ter-wavelength sensing stub resonator. The stub, which must be in contact with the so-called fabric under test (FUT), generates a notch in the transmission coefficient with a resonance frequency that depends on the humidity level of the fabric. By designing the stub with a moderately high quality factor, the variation in the resonance frequency causes a significant change in the magnitude level at the operating frequency, the resonance frequency when the sensing stub is loaded with the dry fabric, and the presence of liquid can be detected by means of an amplitude detector. A prototype device is proposed and experimentally validated.

Shallow Geothermal Energy (SGE) exchanges heat with the ground. In continuous long-term operation, the initial temperature field can be disturbed, and subsurface thermal plumes can be developed. In this paper, the thermal impact of a SGE system under Mediterranean climate is handled. Temperature recordings from 104 thermal probes placed in depth along 15 monitoring boreholes are analysed. Those boreholes were drilled 1-2m from thermos-active boreholes of the case study system installed in a university building. The analysis handles one year of SGE system operation. Temperature depth profiles, reaching up to 140 m depth, were registered with a 10-minute time-step resulting in a large amount of data. Ground thermal conductivity was estimated experimentally and semi-empirically allowing to compute the initial undisturbed ground temperature profiles and compare it with the monitored values. Climate data was recorded by the university meteorological station. Globally, the measured and computed data were coherent and a non-negligible impact of the SGE system operation in the first year was observed. The building orientation as well as the nearby departments had significant impacts on shallow ground temperature. Maximum ground temperature changes, ranging from 2 to 3º C as observed in different boreholes indicating that the system is operating efficiently.

In this article, we have tried to extend the Neumann–Kopp law concerning the heat capacity of solid compounds to other physical observables for materials represented as mixtures of chemical compounds, alloys, and ceramics. The main goal of this study is to find the intervals of external or internal parameters for a solid compound, within which its physical observable - the magnetic transition temperature for this work, can be expressed in terms of the atomic or molar weighted sum of the magnetic transition temperatures of the constituent elements of a compound. Outside these intervals, we tried to figure out the structure of the variable by which the weighted sum should be multiplied. Thus, for USb–x(ThSb) mixtures with a mole fraction x from 0.36 to 0.55, the magnetic transition temperature of this mixture is expressed in term of the molar weighted sum of the temperature of uranium structural transition associated with a change in the magnetic properties of uranium and of the temperature at which the nature of the magnetic susceptibility of antimony changes. For the magnetic Laves phase compounds Er(Fe_0.8–xMn_0.2–yCo_x+y)₂, the Curie temperature of the compound is equal to the weighted sum of the Curie temperatures of all elements of the compound, except for Mn, at x = 0.1, y = 0 and y = 0.1. For the paramagnetic Curie temperature of intercalated dichalcogenides Cr_xМоSe₂, it can be expressed in terms of the weighted Neel temperature of chromium multiplied by a variable depending on x, on the atomic numbers of all elements of the compound, and on a parameter proportional to the derivatives with respect to x of the dichalcogenide’s crystal lattice parameters.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in a form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and sodium nitroprusside. Results showed that Shoot dry weight without fruit (DWPWF) at 40°C in compared to 25°C, 21.54% decreased. Also, foliar application with 100μM melatonin in compared to control (0uM) caused a 13.26% an increased in dry weight of shoots without fruit (DWPWF). Also, leaf chlorophyll at 40°C temperature in compared to 25°C temperature 32.82% decreased and foliar application with 100μM melatonin and 100μM sodium nitroprusside improved leaf chlorophyll value in compared to other foliar application treatments. Foliar application with 50uM and 100uM sodium nitroperoxide at 40°C temperature caused decreased of 15.16% and 20.99% of leaf hydrogen peroxide in compared to 0uM foliar application treatment, respectively. Also, under 40°C temperature, foliar application with melatonin and sodium nitroprusside (50μM and 100μM) in compared to 0μM foliar application activity of leaf superoxide dismutase enzyme increased. Also, leaf nitrogen under with 50 μM and 100μM melatonin in compared to 0μM foliar application 9.61% and 23.72% increased. Leaf potassium in 40°C temperature, foliar application with 50uM melatonin, 100uM melatonin, 50uM sodium nitroprusside and 100μM sodium nitroprusside 55.20, 72, 25.60 and 70.40% in compared to 0uM foliar application increased respectively. leaf iron in foliar application with 100μM sodium nitroprusside in compared to 0μM foliar application 17.96% increased.

Sesame (Sesamum indicum), a highly valued oilseed, faces challenges in cultivation, especially in regions susceptible to environmental stressors. This study investigates the interactive effects of salinity and temperature on sesame seed germination. Two cultivars, Darab 1 and Oltan, were subjected to various salinity levels (-3 to -12 bars) and temperatures (15°C, 20°C, and 25°C). Results revealed that at 15°C, salinity levels beyond -3 bars significantly reduced germination, while at 25°C, 40% and 62% germination rates were recorded even at -12 bars for Darab 1 and Oltan, respectively. The study highlights the importance of temperature in mitigating the inhibitory effects of salinity on germination. Germination speed exhibited a decline with increasing salinity, particularly at lower temperatures. Shoot and root lengths and dry weights decreased with rising salinity, but Oltan demonstrated greater tolerance than Darab 1. The research emphasises the species-specific nature of temperature-salinity interactions and the intraspecific variability among sesame cultivars. Notably, Oltan, adapted to arid regions with elevated temperatures, displayed increased tolerance to salinity stress. The findings contribute to understanding sesame's resilience to environmental stressors, aiding in developing resilient cultivars for challenging agricultural landscapes. Overall, temperature is pivotal in influencing sesame seed germination and early seedling growth under salinity stress, offering insights for optimised cultivation practices.

Socks with the same three-dimensional plantar design, but with different compositions in the separation of their weaves could have different thermoregulatory effects. The objective of this study was therefore to evaluate the temperatures on the sole of the foot after a 10-km run, using two models of socks with different weave separations. In a sample of 20 individuals (14 men and 6 women), plantar temperatures were analysed using a Flir E60bx® (Flir Systems) thermographic camera before and after a run of 10 km wearing two models of socks that had different separations between the fabric weaves (5 mm versus 3 mm). After the post-exercise thermographic analysis, the participants responded to a Likert type survey to evaluate the physiological characteristics of the two models of socks. There was a significant increase in temperature in the areas of interest (p&lt;0.001) after the 10-km run with both models of sock. The temperature under the 1st metatarsal head was higher with the AWC 2.1 model than with the AWC 1 (33.6±2.0°C vs 33.2±2.1°C) (p = 0.014). No significant differences were found in the scores on the physiological characteristics comfort survey (p&gt;0.05 in all cases. The two models presented similar thermoregulatory effects on the soles of the feet, although the model with the narrowest weave separation generated greater temperatures (+0.4°C) under the first metatarsal head.

In this work, thermo-responsive block copolymer brushes modified graphene oxide (GO) nanohybrid was fabricated successfully via the host-guest interaction between β-cyclodextrin functionalized GO and azobenzene-terminated PNIPAM-b-P(St-co-MQ). The block copolymer was synthesized using reversible addition fragmentation chain transfer (RAFT) polymerization based on the monomers of N-isopropylacrylamide (NIPAM), 5-(2-methacryloyl-ethyloxymethyl) -8-quinolinol (MQ), styrene (St) and an azobenzene functional RAFT agent. The 8-hydroxyquinoline units containing in the block polymer can coordinate with CdSe/ZnS quantum dots(QDs) to form a CdSe/ZnS QDs-block copolymer brushes modified graphene oxide fluorescence nanohybrid (QDs/polymer/GO fluorescence nanohybrid) and the resulting fluorescence nanohybrid had a robust temperature responsive property which result from the change in the PNIPAM conformation in the block copolymer on the surface of GO.

The global increase of road infrastructure and its impact on the environment requires serious attention to develop sustainable and environmentally friendly road materials. One group of those materials is produced by using bitumen emulsion. However, there are still scientific and technical obstacles standing against its regular application. The bitumen emulsion formulation process and compositional optimization are subjected to a high number of degrees of freedom. Consequently, obtaining the desired product is mostly based on a series of random and tedious trials because of the enormous number of tests to be carried out. The current review of the physicochemical formulation may indeed be extensively used in helping to reduce the number of unnecessary experimentations as well as discuss the vital aspects in the bitumen emulsion production process. Among these, emulsion stability, viscosity, droplet size (and distribution), bitumen emulsion chemistry, the function of the emulsion components, surfactant type, acids or alkalis, and additives are all discussed and used to define the emulsion's physical properties and reactivity. Besides, current developments in the mechanisms of breaking and setting processes are also summarized. It is discussed how emulsions are graded based on their reactivity, particle charge, and physical features. Two emulsification techniques are outlined namely the colloid mill method and the High Internal Phase Ratio (HIPR) method. Furthermore, some emulsion formulation tools/theories were identified and are explained. In that way, optimized formulations can be used to offer a practical guide for bitumen emulsion manufacturers when trying to formulate a well-defined bitumen emulsion for its use in pavement infrastructure rather than simply to meet standard specifications. This review paper aims to enable the ultimate potential of the bitumen emulsion in the field of cold recycling technology by further following up the research progress of bitumen emulsion manufacturing, therefore, this paper reviews and discusses the literature available up to now on this topic, in road engineering and emulsion chemistry.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Abstract: The effect of some weather parameters (rainfall and temperature) on the production of oil palm in Peninsular Malaysia was investigated. Data were analysed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, time series analysis, and multiple linear regression (MLR) carried out. SPSS and Microsoft Excel 2010 were used to analyse the results. The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature and rainfall (independent variables). The regression output returned three components; regression coefficients, regression statistics and ANOVA. The findings of the study revealed medium to high rainfall variability at the rate of 0.0008. This implies that rainfall is increasing over time with variations in its amount and intensity. As rainfall increases oil palm FFB production is predicted to increase at a slow rate of 0.0009. The estimation of average annual temperature indicated an increase of 5.6℃ at the rate of 0.0357℃ per year with a temperature maximum of 32.01℃ and minimum of 25.45℃. The result also revealed an increase in oil palm yield at the rate of 0.2581 per year with a mean value of 176247.6. Overall, there is a significant difference in the impact of rainfall and temperature on oil palm yield. This signifies that rainfall has a significant impact on oil palm yield (FFB) compared to temperature.

Recent in vivo assays of the responses of Rubisco to temperature in C₃ plants have revealed substantial diversity. Three cultivars of soybean (Glycine max L. Merr.), Holt, Fiskeby V, and Spencer, were grown in indoor chambers at 15, 20, and 25 ^oC. Leaf photosynthesis was measured over the range of 15 to 30 ^oC, deliberately avoiding higher temperatures which may cause deactivation of Rubisco, in order to test for differences in temperature responses of photosynthesis, and to investigate in vivo Rubisco kinetic characteristics responsible for any differences observed. The three cultivars differed in the optimum temperature for photosynthesis (from 15 to 30 ^oC) at 400 µmol mol^-1 external CO₂ concentration when grown at 15 ^oC, and in the shapes of the response curves when grown at 25 ^oC. The apparent activation energy of the maximum carboxylation rate of Rubisco differed substantially between cultivars at all growth temperatures, as well as changing with growth temperature in two of the cultivars. The activation energy ranged from 58 to 84 kJ mol-1, compared with the value of 64 kJ mol^-1 used in many photosynthesis models. Much less variation in temperature responses occurred in photosynthesis measured at nearly saturating CO₂ levels, suggesting more diversity in Rubisco than in electron transport thermal properties among these soybean cultivars.

We demonstrate that multiple well-known metrics, such as the Schwarzschild metric and the extremal solution of the Reissner-Nordstr ̈om metric, can be expressed in what we will call thermodynamic form. These formulations appear to be valid for all Rs = ct growing black holes and, therefore, also within the framework of Rh = ct growing black hole cosmology. However, the metrics can also be applied to non-black hole gravitational objects as long as one calculates the CMB and Hawking temperature of the hypothetical black hole from the gravitational mass.

Ferrite body is the origin of crack and corrosion initiation of steels. Distribution and density of ferrite in seven steel ingots were examined by light optical microscopy and computational modeling in the study to explore the correlation of ferrite formation to chemical composition and mushy zone temperature in ingot forming. The central segregation phenomenon in ferrite distribution was observed in all the examined steel specimens except 0Cr17Ni4Cu4Nb stainless steel. No significant difference was found in distribution and density of ferrite amongst zones of the surface, ½ radius and core in neither risers nor tails of 0Cr17Ni4Cu4Nb ingots. Additionally, fewer ferrite was found in 0Cr17Ni4Cu4Nb compared to other examined steels. The difference of ferrite formation in 0Cr17Ni4Cu4Nb elicited a debate on the traditional models explicating ferrite formation. Considering the compelling advantages in mechanical strength, plasticity and corrosion resistance, further investigation on the unusual ferrite formation in 0Cr17Ni4Cu4Nb would help understand the mechanism to improve steel quality. In summary, we observed that ferrite formation in steel was correlated with mushy zone temperature. The advantages of 0Crl7Ni4Cu4Nb in corrosion resistance and mechanical stability could be resulted from that fewer ferrites formed and distributed in a scattered manner in microstructure of the steel.

Depending on human body conditions and environmental conditions, it is sometimes difficult to conduct subject experiments. In such cases, it is effective to use a thermal manikin. There are few studies that investigate the effect of the non-uniform and asymmetric outdoor thermal environment on the mean skin temperature. The purpose of this study is to clarify the influence of the non-uniform and asymmetric thermal radiation of short-wavelength solar radiation in an outdoor environment on the calculation of the mean skin temperature. The skin temperature of the front of the coronal surface, which was facing the sun and where the body received direct short-wavelength solar radiation, and the skin temperature of the rear of the coronal surface, which was in the shadow and did not receive direct short-wavelength solar radiation were respectively measured. The feet, upper arm, forearm, hand and lower leg, which are susceptible to short-wavelength solar radiation in a standing posture, had a noticeable difference in skin temperature between sites in the sun and in shade. The mean skin temperature of sites facing the sun was significantly higher than the mean skin temperature of those in the shade.

Tropical sea surface temperature (SST) variability, mainly driven by the El Niño–Southern Oscillation (ENSO), influences the atmospheric circulation and hence the transport of heat and chemical species in both the troposphere and stratosphere. This paper uses Met Office, ERA5 and MERRA2 reanalysis data to examine the impact of SST variability on the dynamics of the polar stratosphere and ozone layer over the period 1980 to 2020. Particular attention is paid to studying the differences in the influence of different types of ENSO (East Pacific (EP) and Central Pacific (CP)) for the El Niño and La Niña phases. It is shown that during the EP El Niño, the zonal wind weakens more strongly and changes direction more often than during the EP El Niño, and the CP El Niño leads to a more rapid decay of the polar vortex (PV), an increase in stratospheric air temperature and an increase in the concentration and total column ozone than during EP El Niño. For the CP La Niña, the PV is more stable, which often leads to a significant decrease in Arctic ozone. During EP La Niña, powerful sudden stratospheric warmings are often observed, which lead to the destruction of PV and an increase in column ozone.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

We report on the use of quartz-enhanced photoacoustic spectroscopy (QEPAS) for multi-gas detection. Photo-acoustic (PA) spectra of mixtures of water (H2O), ammonia (NH3) and methane (CH4) were measured in the mid-infrared (MIR) wavelength range using a MIR (mid-infrared) optical parametric oscillator (OPO) light source. Highly overlapping absorption spectra is a common challenge for gas spectroscopy. To mitigate this, we use a partial least-squares regression (PLS) method to estimate the mixing ratio and concentrations of the individual gasses. The concentration range explored in the analysis varies from a few parts-per-million (ppm) to thousands of ppm. Spectra obtained from HITRAN and experimental single-molecule reference spectra of each of the molecular species were acquired and used as training data sets. These spectra were used to generate simulated spectra of the gas mixtures (linear combinations of the reference spectra). Here in this proof-of-concept experiment we demonstrate that after an absolute calibration of the QEPAS cell, the PLS analyses could be used to determine concentrations of single molecular species with a relative accuracy within a few % for mixtures of H2O, NH3 and CH4 and with an absolute sensitivity of approximately 300(±50) ppm/V, 50(±5) ppm/V and 5(±2) ppm/V for water, ammonia and methane, respectively. Thus, demonstrating that QEPAS assisted by PLS is a powerful approach to estimate concentrations of individual gas components with considerable spectral overlap, which is a typical scenario for real-life adoptions and applications.

Global warming may increase the potential evapotranspiration (Etp), thereby affecting the amount of clean water resources available in a region. In this study, the systematic biases in temperature outputs of 24 global climate models (GCMs) under 3 emission scenarios are corrected by using 8 bias correction methods. The trend of Etp in Yangzi River Delta in the 21st century is projected by using 4 Etp calculation formulas. The uncertainty of the projections is estimated and decomposed by using multi-way analysis of variance. The influence of uncertainty on the projected change signal is quantified by using the signal-to-noise ratio. The results show that, relative to the reference period (1971~2000), the annual mean daily Etp in Yangzi River Delta will increase by 0.14~0.17mm/d during the period 2021~2050 and by 0.21~0.41mm/d during the period 2061~2090, respectively. During 2021~2050, the uncertainty of Etp increase projections is dominantly contributed by the main effects of GCM (63%) and Etp calculation formula (24%). During 2061~2090, it is mainly contributed by the main effect of GCM (36%), followed by the main effects of emission scenario (34%) and Etp calculation formula (18%). The increase projections of Etp are generally reliable and robust during the two projection periods.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.