The power utility, Tanzania Electric Supply Company Limited (TANESCO) is faced with challenges of supplying adequate power to the ever-increasing demand. To this end, this paper explores the installed Ubungo Gas Power Plant (UGP II) located in Dar es Salaam to find means of utilizing it in co-generation method. The study embarked on detailed modelling of the system and run simulations which indicated that the co-generation can result to power generation efficiency increase between 10.42 to 50.92%. It is recommended to change the UGP II to exploit this co-generation method. Further, the study could be improved by including more parameters of the gas and steam plant and verify them experimentally.

In this article, management control has been studied from the perspective of intention towards sustainable development of companies. The main idea focuses on the analysis of relations between sustainable management control and the system of performance appraisal using as a reference the resource-based theory. These relations have been assessed both theoretically by reviewing literature in the field, and empirically based on data collected in a questionnaire from top management, as well as data from Annual Reports from the main segment of Bucharest Stock Exchange. The authors have shown that financial performance has a significant influence on management control, and the return on capital employed is one of the most recommended indicators. The sustainable nature attributed to management control is the result of institutional theory evolution, provisions of Directive 2014/95/EU and Guide of Global Management Accounting Principles (2015) using stewardship. Consequently, profits are not the main element any more in the assessment of financial „health” of a company. To ensure the sustainable success, sustainable balanced scorecard is one of real measures for managing financial and non-financial performance.

This research presents alternative solutions for an Energy Efficiency Management System (EEMS) serving as a framework for optimizing the energy consumption algorithm and lowering energy consumption. First, a monitoring Wireless Sensor and Actuator Network (WSAN) is used for sensing, measuring, gathering data, and modeling all the dynamic disturbance parameters of the rooms in the building. Second, integrated software for metering and controlling the processes of digital data flow is used. Third, an alternative solution is proposed to reduce energy consumption. The primary benefits of this system are real-time monitoring; rapid, alternative solutions; and the ability to make a prudent decision on how to lower energy consumption. The system shows instant and accumulated solutions for short and long-term time planning. The solutions identified can be implemented in the same buildings under the same circumstances. The universities of Majmaah and Philadelphia have buildings with similar infrastructure. The system was applied to the buildings at Philadelphia University. The results were generalized to both universities. After implementation, the energy consumption of the EEMS using WSAN (based on the monitoring was reduced up to 23% when compared to that of the initial state.

It is proposed that both human creativity and human consciousness are (unintended) consequences of the human brain’s extraordinary energy efficiency. The topics of creativity and consciousness are treated separately, though have a common sub-structure. It is argued that creativity arises from a synergy between two cognitive modes of the human brain (which broadly coincide with Kahneman’s Systems 1 and 2). In the first, available energy is spread across a relatively large network of neurons. As such, the amount of energy per active neuron is so small that the operation of such neurons is susceptible to thermal (ultimately quantum decoherent) noise. In the second, available energy is focussed on a small enough subset of neurons to guarantee a deterministic operation. An illustration of how this synergy can lead to creativity with implications for computing in silicon are discussed. Starting with a discussion of the concept of free will, the notion of consciousness is defined in terms of an awareness of what are perceived to be nearby counterfactual worlds in state space. It is argued that such awareness arises from an interplay between our memories on the one hand, and quantum physical mechanisms (where, unlike in classical physics, nearby counterfactual worlds play an indispensable dynamical role) in the ion channels of neural networks. As with the brain’s susceptibility to noise, it is argued that in situations where quantum physics plays a role in the brain, it does so for reasons of energy efficiency. As an illustration of this definition of consciousness, a novel proposal is outlined as to why quantum entanglement appears so counter-intuitive.

Taking capital, manpower, and natural resources as inputs, regional GDP as expected output, and industrial pollution as undesired output, this study measures the ecological efficiency of various regions in China through the Global-Malmquist model. The results show a trend of an initial sharp decline in ecological efficiency followed by a gradual increase in the time dimension, but there is no significant correlation in the spatial dimension. Using the gravity model to quantify the attractiveness of the regions’ capital and human resources for collaborative innovation, it estimates the impact of collaborative innovation on eco-efficiency through the system-Generalized Method of Moments (GMM) model. The results show that technological innovation capital in other regions has a negative “U” relationship with local ecological efficiency, while scientific and technological innovation human resources have a positive “U” relationship. In addition, government financial support in science and technology and the ecological efficiency of the previous period serve as promoting factors of the current local ecological efficiency, while the introduction of foreign technological innovation is likely to inhibit improvements in ecological efficiency. Based on these findings, this study puts forward corresponding policy recommendations for local governments to advance their development agendas alongside their environmental priorities in line with their specific circumstances.

The theoretical limits of water sorbate based chemical sorption heat storage are investigated in this study. First, a classification of \textit{thermochemical heat storage} is proposed based on bonding typology. Then, thermodynamics of chemical solid/gas sorption is introduced. The analysis of the reaction enthalpy from the literature indicates that this value is only slightly varying for one mole of water. Using this observation, and with the help of thermodynamical considerations, it is possible to derive conclusions on energy efficiency of closed and open heat storage systems. Whatever the salt, the main results are 1) the energy required for evaporation of water is, at least, 65% of the available energy of reaction and 2) the maximum theoretical energy efficiency of the system is about 1.8.

Solar energy is a renewable resource of energy that is broadly utilized and has the least emissions among the renewable energies. In this study, machine learning methods of artificial neural networks (ANNs), least squares support vector machines (LSSVM), and neuro-fuzzy are used for advancing prediction models for thermal performance of a photovoltaic-thermal solar collector (PV/T). In the proposed models, the inlet temperature, flow rate, heat, solar radiation, and the sun heat have been considered as the inputs variables. Data set has been extracted through experimental measurements from a novel solar collector system. Different analyses are performed to examine the credibility of the introduced approaches and evaluate their performance. The proposed LSSVM model outperformed ANFIS and ANNs models. LSSVM model is reported suitable when the laboratory measurements are costly and time-consuming, or achieving such values requires sophisticated interpretations.

This paper presents a study on the thermal efficiency improvement of the user equipment room in the district heating system based on reinforcement learning [1], and suggests a general method of constructing a learning network(DQN)[2] using deep Q learning[3], which is a reinforcement learning algorithm that does not specify a model. In addition, we introduce the big data platform system and the integrated heat management system for the energy field in the massive data processing from the IoT sensor installed in large number of thermal energy control facilities.

The ongoing revolution in Deep Learning is redefining the nature of computing that is driven by the increasing amount of pattern classification and cognitive tasks. Specialized digital hardware for deep learning still holds its predominance due to the flexibility offered by the software implementation and maturity of algorithms. However, it is being increasingly desired that cognitive computing occurs at the edge, i.e. on hand-held devices that are energy constrained, which is energy prohibitive when employing digital von Neumann architectures. Recent explorations in digital neuromorphic hardware have shown promise, but offer low neurosynaptic density needed for scaling to applications such as intelligent cognitive assistants (ICA). Large-scale integration of nanoscale emerging memory devices with Complementary Metal Oxide Semiconductor (CMOS) mixed-signal integrated circuits can herald a new generation of Neuromorphic computers that will transcend the von Neumann bottleneck for cognitive computing tasks. Such hybrid Neuromorphic System-on-a-chip (NeuSoC) architectures promise machine learning capability at chip-scale form factor, and several orders of magnitude improvement in energy efficiency. Practical demonstration of such architectures has been limited as performance of emerging memory devices falls short of the expected behavior from the idealized memristor-based analog synapses, or weights, and novel machine learning algorithms are needed to take advantage of the device behavior. In this work, we review the challenges involved and present a pathway to realize ultra-low-power mixed-signal NeuSoC, from device arrays and circuits to spike-based deep learning algorithms, with ‘brain-like’ energy-efficiency.

Solar energy is a renewable resources of energy which is broadly utilized and have the least pollution impact between the available alternatives of fossil fuels. In this investigation, machine leaening approaches of neural networks (NN), neuro-fuzzy and least squares support vector machine (LSSVM) are used to build the models for prediction of the thermal performance of a photovoltaic-thermal solar collector (PV/T) by estimating its efficiency as an output of the model while inlet temperature, flow rate, heat, solar radiation, and heat of sun are input of the designed model. Experimental measurements was prepared by designing a solar collector system and 100 data extracted. Different analyses are also performed to examine the credibility of the introduced approaches revealing great performance. The suggested LSSVM model represented the best performance regarding the mean squared error (MSE) of 0.003 and correlation coefficient (R²) value of 0.99, respectively.

Innovative practices in irrigation systems can bring improvements in terms of economic efficiency and in the same time can reduce environmental impact. Investment in high tech technologies frequently involves additional costs, but an efficient water management can increase the lifetime of the equipment. The main objective of this article is to reduce the energy consumption by one thousand cubic meters pumped and automatically to increase the economic efficiency of the pumping groups. This paper develops a new operating algorithm that ensures the operation of the pumping group at safe operating intervals and in the same time identifies the equivalent pump operating points for the entire flow range and pumping height of the pumping group. This methodology is based on the principles of an Expert System to perform the optimization process of the energy consumption in pumping groups. The resulting methodology avoids the combinatorial explosion of the solutions to be analyzed and determines the point of maximum efficiency without violation of any of the system constraints under any operating condition. The proposed methodology is tested on an irrigation system that includes a pumping group with 5 pumps, showing its effectiveness in obtaining the optimal solution with a relatively low computational burden.

A novel approach to the remote-control system for the compact multi-crystal energy-dispersive spectrometer for x-ray emission spectroscopy (XES) applications has been developed. This new approach is based on asynchronous communication between software components and on reactive design principles. In this paper, we identify the challenges we have faced, our solution to them as well as the implementation and future development prospects. The main motivation of this work was the development of a new holistic communication protocol that can be implemented to control various hardware components.

The major goal of this paper is to use image enhancement techniques for enhancing and extracting data in FANET applications to improve the efficiency of surveillance. The proposed conceptual system design can improve the likelihood of FANET operations in oil pipeline surveillance, and sports and media coverage with the ultimate goal of providing efficient services to those who are interested. The system architecture model is based on current scientific principles and developing technologies. A FANET, which is capable of gathering image data from video-enabled drones, and an image processing system that permits data collection and analysis are the two primary components of the system. Based on the image processing technique, a proof of concept for efficient data extraction and enhancement in FANET situations and possible services is illustrated

The process of modelling energy systems is accompanied by challenges inherently connected with mathematical modelling. However, due to modern realities in the 21st century, existing challenges are gaining in magnitude and are supplemented with new ones. Modellers are confronted with a rising complexity of energy systems and high uncertainties on different levels. In addition, interdisciplinary modelling is necessary for getting insight in mechanisms of an integrated world. At the same time models need to meet scientific standards as public acceptance becomes increasingly important. In this intricate environment model application as well as result communication and interpretation is also getting more difficult. In this paper we present the open energy modelling framework (oemof) as a novel approach for energy system modelling and derive its contribution to existing challenges. Therefore, based on literature review, we outline challenges for energy system modelling as well as existing and emerging approaches. Based on a description of the philosophy and elementary structural elements of oemof, a qualitative analysis of the framework with regard to the challenges is undertaken. Inherent features of oemof such as the open source, open data, non-proprietary and collaborative modelling approach are preconditions to meet modern realities of energy modelling. Additionally, a generic basis with an object-oriented implementation allows to tackle challenges related to complexity of highly integrated future energy systems and sets the foundation to address uncertainty in the future. Experiences from the collaborative modelling approach can enrich interdisciplinary modelling activities. Our analysis concludes that there are remaining challenges that can neither be tackled by a model nor a modelling framework. Among these are problems connected to result communication and interpretation.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

FPGA-based data acquisition and processing systems play an important role in modern high-speed, multichannel measurement systems, especially in High-Energy and Plasma Physics. Such FPGA-based systems require an extended control and diagnostics part corresponding to the complexity of the controlled system. Managing the complex structure of registers while keeping the tight coupling between hardware and software is a tedious and potentially error-prone process. Various existing solutions aimed at helping that task do not perfectly match all specific requirements of that application area. The paper presents a new solution based on the XML system description, facilitating the automated generation of the control system’s HDL code and software components and enabling easy integration with the control software. The emphasis is put on reusability, ease of maintenance in case of system modification, easy detection of mistakes, and the possibility of use in modern FPGAs. The presented system has been successfully used in data acquisition and preprocessing projects in High-Energy Physics experiments. It enables easy creation and modification of the control system definition and convenient access to the control and diagnostic blocks. The presented system is an open-source solution and may be adopted by the user for particular needs.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

There has been rampant fold-ups, merger and acquisitions occurring in the Ghanaian banking industry. Then, the questions arise: Is the Ghanaian Financial System in Crisis? This study was conducted to find answers to these problems unsolved with prior literature. A sample of seventy customers of the Royal Bank, 8 employees of the Royal Bank and 2 managers of the Royal Bank were selected for a case-survey. The study also monitored the Trend of the Ghanaian Financial System through the reading and monitoring of daily news on the Financial System and reports of banks. The data from the field and the secondary data from news and reports were analysed symmetrically. The study drew on Minsky’s Financial Crisis Theory to explain the phenomenon in the Ghanaian economy and to draw predictions of what would happen in other developing economies. The study found out that: (1) The Ghanaian financial system is fragile and it holds true for most developing economies; (2) The financial system suffers greatly when the confidence level of customers falls significantly; (3) Management information systems raises the confidence level of customers (borrowers and lenders) such that there is a greater fall and impact in times of instability in the economy; (4) The higher the level of MIS adoption in an unstable economy, the more fragile the Financial System becomes and (5) A higher adoption of Management Information Systems in a Fragile Financial System indirectly contributes to Financial Crisis of the Financial System.

This paper deals with the problem of real-time management of Smart Grids. For this sake, the energy management is integrated with the power system through a telecommunication system. The use of Multiagent Systems leads the proposed algorithm to find the best-integrated solution, taking into consideration the operating scenario and the system characteristics. The proposed technique is tested with the help of an academic microgrid, so the results may be replicated.

This paper reviews the design and component of two types of RWHS, namely roof harvesting system (RHS) and pond harvesting system (PHS). The performance in terms of quantity and quality of collected rainwater and energy consumption for RWHS with different capacities were evaluated, as well as the benefits and challenges particularly in environmental, economic and social aspects. Presently, RHS is more commonly applied but its effectiveness is limited by its small scale. The PHS is of larger scale and has greater potentials and effectiveness as an alternative water supply system. Results also indicate the many advantages of PHS especially in terms of economics, environmental aspects and volume of water harvested. While RHS may be suited to individual or existing buildings, PHS has greater potentials and should be applied in newly developed urban areas with wet equatorial climate.

Age-in-place can reduce the progress of dementia syndrome and improve the quality of life of the sufferers and their families. This work proposes an innovative information home support system to be established at the houses of people suffering from dementia. The main innovation of the system are its transparent character that overcomes the need for training of the sufferer, as well as the exploitation of a well-known technique for dementia, namely music therapy. It addresses the need of people suffering from dementia as well as their familiars to be recognized by them and have better interaction and collaboration. The system offers a ubiquitous recognition system, just by using smart devices like smart-phones or smart-wristbands. When a familiar person is detected in the house, then a sound file is reproduced on smart speakers placed in the house, in order to trigger the memory, based on the principles of music therapy. The system reproduced the appropriate time at 100% of the cases and the benefits of music therapy are evident daily. To the best of the authors' knowledge, this is the first system of its kind ever reported in the literature.

In graduate programs such as social work, field education is the signature pedagogy of education. As such, student placement with an appropriate field education agency is critical to ensure academic success and career readiness. A variety of Learning Management System (LMS) and Integrated Planning and Advising Service (IPAS) technologies have been developed to fully integrate technology into the educational system and streamline and improve the learning experience for students, educators, and administrators. Few (if any) of the existing solutions have capabilities to match students with field educators on the basis of an individual student’s completed coursework and area of specialization, as well as field educator needs and opportunities. This paper describes our experience developing a custom LMS/IPAS system—the School of Social Work information System (SSWiS)—that was designed specifically for student learning, faculty advising, and academic administration within our social work graduate program. We present the challenges that motivated the design of the SSWiS before describing the architecture and functionality of our solution. We then discuss our preliminary evaluation results. We conclude with a discussion of the benefits and limitations of our system in the context of today’s technical needs in graduate education in social work and other fields.

Rice wheat cropping system prevailed in more than fifty percent areas of rice belt of central and upper Punjab. In this area yield of wheat is curtailed every year due to late harvesting of rice crop. In addition to this, lack of machinery for direct sowing of wheat into combine harvested rice is a major limitation for timely wheat sowing due to presence of heavy straw load dropped by the combine harvester. A field experiment was planned and executed during two consecutive years 2017-18 and 2018-19 at Agronomic Research Station Farooqabad to evaluate the various stubble management techniques for the sowing of wheat in a rice-wheat cropping system. The Experiment consist of four treatments Happy seeder (Zero tillage), conventional sowing without burning of rice stubble, Rotavator two times, and Conventional sowing with the burning of rice stubble. The trail was arranged as a Randomized Complete Block Design with four replications having a net plot size of 8 m x 20 m. The Treatments have significant effects on Plant height, Number of productive tillers, 1000- grain weight, and grain yield. Maximum plant height (94.74 and 94.25 cm), numbers of productive tillers/m2 (324.00 and 322.25), 1000-grain weight (36.35 and 36.20 g), grain yield (3780 and 3613 kg/ha), and benefit-cost ratio (2.54 and 2.43) were recorded from the treatment happy seeder (Zero tillage) during both years respectively. It is concluded that the sowing of wheat with a happy seeder (Zero tillage) is an appropriate technique in the rice-wheat cropping system by protecting the environment and soil health from the burning of rice stubbles.

Differential equation models to understand interaction between plant and nutrient solution are presented. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient along the cell membrane. It establishes electrical field with Nernst potential to make positively charged ions outside the cell membrane flow into the root cell. Anion influx is also modulated by H+ ion concentration because plant root cell absorbs negatively charged particles with symport. If an anion collides with H+ cell to make net charge as neutral, at symport channel, it can flow through. In this paper, mathematical models for cation and anion absorption are introduced. Cation absorption model was induced from Ohm's law combined with Goldman's equation. Anion absorption model is similar to chemical reaction rate model. Both models have physiological terms influenced by gene expression pattern, species or phenotypes. Cation model also includes terms for ion's kinetic and electrical properties, growth of plant and interaction between the root and the surroundings. Simulation for 20 different sets of coefficients showed that the physiology-related coefficient has important role on nutrition absorption tendencies of plants.

We have presented a controllable and human-readable polynomial neural network (CR-PNN) that is the first human-readable neural network. One can imagine its influence on system identification. Subsequently, we developed a relation spectrum in a medical application, which is likely to stand alongside the Fourier spectrum. However, the system analysis methodology is incomplete in contrast to signal processing methodology. Here, we presented the system filters for the first time. In this paper, we used the simulation system to verify the availability of the system analysis methodology. The system analysis methodology showed great properties in system identification and filter. The contribution of this paper is the system analysis methodology: transform method (CR-PNN), relation spectrum, and system filter design.

Climate projections show that southern Indonesia such as West Nusa Tenggara is projected to experience a lower precipitation and higher temperatures. To date, research on climate change impact on Indonesian rice production yield is limited. As climate change is projected to decrease rainfall and to increase temperatures, this paper offers a qualitative analysis using system archetypes to understand the impacts of climate change on rice production. Two system archetypes are identified including Limits to Growth and Success to Successful. Both archetypes explain that rice production is hampered by high minimum temperature as photosynthesis output is decreased by increasing respiration. This paper shows that using a simple tool, system archetypes, we can describe the impacts of climate change on rice production. The outputs of this study such as a causal loop diagram and system archetypes can be a basis to develop a simulation model in understanding the impacts of climate change on main crops.

In this article, we consider the three dimensional $\alpha$-fractional nonlinear delay differential system of the form \begin{align*} D^{\alpha}\left(u(t)\right)&=p(t)g\left(v(\sigma(t))\right),\\D^{\alpha}\left(v(t)\right)&=-q(t)h\left(w(t))\right),\\D^{\alpha}\left(w(t)\right)&=r(t)f\left(u(\tau(t))\right),~ t \geq t_0, \end{align*} where $0 < \alpha \leq 1$, $D^{\alpha}$ denotes the Katugampola fractional derivative of order $\alpha$. We have established some new oscillation criteria of solutions of differential system by using generalized Riccati transformation and inequality technique. The obtained results are illustrated with suitable examples.

Power system decentralization has been an emerging topic for the past decade in an effort to improve power quality and environment protection via increased integration of renewable energy sources. Towards these objectives, decentralized microgrids have been proposed and thoroughly investigated in terms of technical capabilities and economic performance. In fact, the planning and actual operation of small-scale, decentralized microgrids has started in countries such as Canada, Japan, USA, UK and other countries. It is expected that the research in this area will progress and eventually take over the existing paradigm of large-scale power generation in the future. These small-size decentralized microgrids could be connected with nearby microgrids under normal operating conditions, but under special events, such as natural or man-made disasters, they would be disconnected and run in islanded mode. Under such high impact – low probability events, the microgrid must have resiliency to successfully re-connect with other microgrids and the main grid. In this paper, an Energy Management System (EMS) for a microgrid having a resiliency function, allowing to operate under islanded mode after an accident, is proposed. The proposed tool, called Resilient Energy Management System (ResEMS), aims at procuring reserve power into the microgrid’s Battery Energy Storage System (BESS) effectively, by importing it from the nearby connected power system. The accident is assumed to be a predictable natural disaster, which means that the accident occurrence time, duration and level of damage can be estimated. The proposed ResEMS has been applied to a microgrid comprising of a BESS, a diesel generator and several photovoltaic devices. The simulation results verify its beneficial operation.

Risk-based redispatch optimization is proposed as a methodology to support the Transmission System Operator (TSO) with preventive remedial actions obtained by extending the security constrained unit commitment/economic dispatch with constraints resulting from the risk assessed for the power system. Although being heuristic, the methodology is based on comprehensive dynamic security assessment as time-domain simulations are used, allowing to express the degree of all types of instabilities, e.g., caused by contingencies, in monetary terms. Therefore, the risk is assessed as the expected value of the cost incurred by the TSO. Such approach forms a new pathway to including risk in planning procedures already used by TSOs. Results obtained for the IEEE39 dynamic power system, with costs assigned to load shedding and generator tripping due to single transmission lines short-circuits, are shown as a reference case.

This paper proposes a real-time local positioning system (RT-LPs) utilizing a mobile platform equipped with three anchor nodes placed in a right-angle triangle formation for a real-time locating system (RTLS). After deriving an analytic formula to calculate the target position utilizing the measured distances among anchor nodes and the target node, we find that four parameters have an effect on the position error of the target node. The spacing between anchors is a design parameter that must be large enough to the reduce position error. However, the distance from the anchor node to the target node is an operation parameter that must be small enough to reduce the position error. Additionally, the measured ranges among the anchors and the target node have probabilistic distributions with a mean and variance, which are dominant parameters that have effects on the position error. A comparison study was conducted to determine the effects of the parameters of the target position in both a simulation and an experiment, showing rates of approximately 4% ~ 10%. These findings indicate that our simulation can work properly with the proposed method after assuming that the distance error is a Gaussian model.

Spatio-temporal aspects of data lead to critical information. Sensors capture data at all scales continually so it is imperative that useful information be extracted ubiquitously and regularly. Location plays a vital part by helping understand relations between datasets. It is crucial to link developmental works with spatial attributes and current challenge is to create an open platform that manages real-time sensor data and provides critical spatial analytics atop expert domain knowledge provided in the system. That is a two-faced problem where the solution tackles not only data from multiple sources but also runs data management platform, a spatial data infrastructure(SDI) as backbone framework able to harness sensor web(SW). The paper proposes development of such a globally shared open spatial expert system(ES), SmaCiSENS, a first of a kind geo-enabled knowledge based(KB) ES for multiple fields, smarter cities to climate modeling. SmaCiSENS is integration of SW and SDI with domain KB on data and problems, ready to infer solutions. The paper describes an architecture for semantic enablement for SW, SDI; connect interfaces, functions of SDI and SW, and sensor data application program interfaces (APIs) to better manage climate modeling, geohazard, global changes, and other vital areas of attention and action.

Groundwater degradation is a global problem linked to irrigation agriculture and aggravated by climate change. In drylands, where aquifer recharge is low, irrigation has emerged as an engine of economic growth. This problem falls under the paradigm of desertification, as it fits the definition of this complex problem in that the degradation of drylands is due to climatic variations and inappropriate human activities. Land Degradation Neutrality (LDN), the response of the United Nations Convention to Combat Desertification to the lack of progress in tackling desertification, is integrated into Sustainable Development Goal 15.3 and provides the adequate framework for implementing effective solutions. LDN prioritizes prevention strategies, and early warning systems coupled to integrated simulation models is a sound approach. We analyze the dynamics of a coastal aquifer in southern Spain, a “desertification landscape” according to the Spanish National Action Plan to Combat Desertification. For this purpose, we have (i) adapted a generic desertification model that considers socio-ecological systems as a particular case of predator-prey systems; and (ii) coupled to this model a risk analysis to calculate the probabilities of groundwater salinization under the current scenario of water resources use, driven by the expansion of greenhouse agriculture supported by external water transfer. The risk of desertification is close to 100%: groundwater salinity is 40 dS m-1 (well above tomato tolerance, 3.5 dS m-1), and 2.4 Mm3 yr–1 water transfer is needed to support the 631 ha of greenhouses. This worrying result suggests that complimentary solutions should be promoted to deactivate the ongoing process of desertification. Among them, we propose reclaimed water, diversifying the economy, or promoting crops adapted to aridity. This simulation framework shows how to explore the future of a socio-ecosystem under current scenarios and others that consider climate change, the energy crisis, or the impact of alternative solutions.

This article analyses entropy changes triggered by specific events in deterministic and indeterministic systems. Article considers a simple model consisting of water in a cuvette, an ice cube in the device above the cuvette and a random number generator (RNG) that controls the probability of dropping the ice into water. Article introduces the entropic potential Z(T, A) of an event A occurred in a system R at the moment Т₀, which describes the influence of the event A to the entropy of the system R in the future (for the moments T>Т₀). The entropic potential of an event Z(T,A) can be calculated as the difference between the mathematical expectations of entropy of the system R for the moment T (T>Т₀) made immediately before and immediately after the event A as Z(T, A) = Ŝ_T(Т₀+dT) - Ŝ_T(Т₀-dT). Article also presents examples of calculations of the entropic potentials of events in indeterministic systems with different probabilities of events. Since real-life systems are mostly indeterministic, the entropic potentials of events in real-life usually have non-zero values. The entropic potentials of the events "useful" for the system are negative, and entropic potentials of the events "harmful" for the system are positive.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

The effect of the negative effective mass emerging in the gravitating core-spring-shell system is considered. The effect appears when the entire system is exerted to the external harmonic force and the frequency of external force approaches to the critical frequency from above. The critical frequency depends on the density of the self-gravitating system only. The scaling law predicting the value of for condensed phases is derived. The generalization of the effect for the Coulomb-like forces is reported

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

This paper presents a comparison between a kite model with a constant-length tether and a model based on a system identification algorithm. The concept of system identification is applied to predict the uncertainties related to the variation of the wind speed and the shape deformation of the tethered membrane wing during flight. A pole-placement controller is used to ensure that the kite follows the planned flight path. Thus, we can determine the required locations of the closed loop poles, and then enforce them by changing the controller's gains in real-time. The capability of the system identification algorithm to recognize sudden changes in the dynamic model, and the ability of the controller to stabilize the system in the presence of such changes are confirmed. Furthermore, the system identification algorithm is applied to determine the parameters of a kite with variable-length tether used in a flight test of the 20 kW kite power system of TU Delft. Experimental data of this test were compared with the system identification results in real-time and significant changes were observed in the parameters of the dynamic model which heavily affect the resulting response.

In Safety Management System (SMS), the risk management plays a key role for the prevention of accidents. The aim of this paper is to propose a Safety Management model using a system dynamic approach to update conventional industrial safety into the new industrial safety 4.0 that is time to developed. This study analyzes some safety 4.0 aspects lacked in the Bhopal incidental event by considering different data detected in the industrial Plant. The model proposed in this paper discusses the relationships among the main causes that have contributed to the occurrence of the incidental event studied, such as broken safety devices, inadequate personnel experience, operator decisions, manager production strategy, policy decision, as deduced from the relevant literature about Bhopal incidental dynamic.

The following series of Articles about a contextual system-theory, with focus on biological systems, shall give a guideline of how to explore complex systems. It is written not only for scientists, and therefore I will try to describe part of the way of understanding as an intuitive approach. This approach will also help scientists to get a deeper understanding of complexity. Some definitions and rules may seem at first simple and obvious. If practiced in a multidimensional complex system, one will see the difficulties. Even without mathematization or computer modeling the multidimensional sub space, which we try to describe phenomenologically for approaching the understanding of this Subsystem, will need a lot of training. Easily we get lost in the multidimensional world. Some of the chapters here and in the following publications of this series are written for specialists, but it will always come back to the essence of a phenomenological description. Concepts like Symbolic programming, Object oriented modeling, simulation and optimizing as well as experimental and mathematical approaches are the described tools to unpuzzle a complex scenario.

An actual problem of inertial navigation related to the creation of a multifunctional device that performs the functions of a meter for both angular velocities and linear accelerations is considered. The possibility of constructing such a device based on a hybrid-type modulation micromechanical gyroscope has shown. The ability to measure linear accelerations has provided by the presence of a small symmetrical distance between the axes of the elastic suspension relative to the center of mass of the sensor element. A mathematical model of the device ("heavy" gyroscope) as a high-quality three-dimensional oscillatory system is constructed. It has shown numerically that the reaction of the system to the movement of an object has, along with precession, the observed nutation. This allows you to develop an algorithm for separating information about the angular and linear motion of the base and implement a two-component angular velocity meter and a two-component linear acceleration meter in one device.

We consider finite and unconditionally convergent infinite expansions of elements of a given topological monoid G in some base B c G as words of the alphabet B, identify insignificantly different words and define a multiplication and a topology on the set of classes of these words. Classical numeral systems are particular cases of this construction. Then we study algebraic and topological properties of the obtained monoid and, for some cases, find conditions under which it is canonically topologically isomorphic to the initial one.

Origin, mechanics and properties of the Solar System are analysed in the framework of the Complete Relativity theory (by the same author). According to Complete Relativity, everything is relative. Any apparent absolutism (notably invariance to scale of dimensional constants, absolute elementariness, invariance to time) is an illusion stemming from limits imposed by [or on] polarized observers that will inevitably lead to misinterpretation of phenomena (another illusion) occurring on non-directly observable scales or even on observable but distant scales in space or time. If everything is relative, reference frames will exist where particles are planets and where planets are living beings. Earth is, therefore, analysed here in more detail, both as a particle and, as a living evolving being (of, hypothesized, extremely introverted intelligence). The analysis confirms the postulates and hypotheses of the theory (ie. existence of discrete vertical energy levels) with a significant degree of confidence. During the analysis, some new hypotheses have emerged. These are discussed and confirmed with various degrees of confidence. To increase confidence or refute some hypotheses, experimental verification is necessary. Main conclusions that stem from my research and are further confirmed in this paper are: universes are, indeed, completely relative; Solar System is a scaled (inflated, in some interpretations) Carbon isotope with a nucleus in a condensed (bosonic) state and components in various vertically excited states; life is common everywhere, albeit extroverted complex forms are present on planetary surfaces only during planetary neurogenesis; anthropogenic climate change is only a part (trigger from one perspective) of bigger global changes; major extinction events on a surface of a planet are relative extinctions, a regular part of transformation and transfer of life in the process of planetary neurogenesis.

Since the launch of Protein Data Bank (PDB) in 1971, Cartesian coordinate system (CCS) has been the default approach to specify atomic positions in biomolecular experimental structures with X, Y and Z. In 2020, a local spherical coordinate system (LSCS) approach was proposed as an alternative to CCS, i.e., ρ, θ and φ. Recently, the continued application of deep learning technology in protein structure prediction (PSP) saw a leap forward in the accuracy of PSP, as evidenced by AlphaFold of Google’s DeepMind. However, there still is room for the improvement of the performances of PSP algorithms to date. Given that geometrically, CCS and LSCS are like the two sides of a coin, this short article puts forward a hypothesis that the time is now ripe to end the half-a-century burial of ρ, θ and φ in PDB, and use them as LSCS features for the design of novel PSP algorithms in future.

Emotion plays a powerful role in humans’ interaction with robots. In order to express more human-friendly emotions, robots need the capability of contextual appraisal that expresses the emotional relevance of various targets in the spatiotemporal situation. In this paper, an emotional appraisal methodology is proposed in this study to cope with such contexts. Specifically, the Ortony, Clore, and Collins model is abstracted and simplified to approximate an emotional appraisal model in the form of a sentence-based cognitive system. The contextual emotion appraisal is modeled by formulating the emotional relationships among multiple targets and the emotional transition with events and time passing. To verify the proposed robotic system’s feasibility, simulations were conducted for scenarios where it emotional interacts with humans manipulating liked or disliked objects on a table. This experiment demonstrated that the robot's emotion can variously change over time like human by using a proposed formula for emotional valence, which is moderated by emotion appraisal of occurring events.

The implementation of teaching interventions in learning needs has received considerable attention, as the provision of the same educational conditions to all students, is pedagogically ineffective. In contrast, more effectively considered the pedagogical strategies that adapt to the real individual skills of the students. An important innovation in this direction is the Adaptive Educational Systems (AES) that support automatic modeling study and adjust the teaching content on educational needs and students' skills. Effective utilization of these educational approaches can be enhanced with Artificial Intelligence (AI) technologies in order to the substantive content of the web acquires structure and the published information is perceived by the search engines. This study proposes a novel Adaptive Educational eLearning System (AEeLS) that has the capacity to gather and analyze data from learning repositories and to adapt these to the educational curriculum according to the student skills and experience. It is a novel hybrid machine learning system that combines a Semi-Supervised Classification method for ontology matching and a Recommendation Mechanism that uses a hybrid method from neighborhood-based collaborative and content-based filtering techniques, in order to provide a personalized educational environment for each student.

In this paper, we are proposing a bio-inspired location management (LM) technique for personal communication system (PSC). It is based on artificial immune system (AIS), with self-adaptation and self-updates attributes in order to perform the location management, and work helps to achieve the better quality of service (QoS) and quality of experience (QoE) for the mobile users. Here, we are suggesting a modified mobile switching center (MSC) architecture, and an adaptive self-modified location management procedure. The proposed mobile switching centre architecture has an advantage of rule-based and fact-based system to store the rules and fact related to location management procedure, and it shows the intelligent behavior of system. The mobile switching centre calculates the best method for location management and rule-base system trigged the rules to perform the techniques. The system stores the result (techniques for location management) in fact-base system for future use. The efficiency and effectiveness of the proposed techniques been analyzed, and it observed that the proposed system has 45-50% improvement in performance over the current location management techniques. Here, we are taking the performance parameters such as signaling cost, database update cost, overhead measurement, mobility management cost.

Preeclampsia is a multifactorial cardiovascular disorder diagnosed after 20 weeks of gestation that is the leading cause of death for both mothers and babies in pregnancy. The pathophysiology remains poorly understood due to variability and unpredictability of disease manifestation when studied in animal models. After preeclampsia, both mothers and offspring have a higher risk of cardiovascular disease (CVD) including myocardial infarction or heart attack and heart failure (HF). Myocardial infarction is an acute myocardial damage that can be treated through reperfusion, however, that therapeutic approach leads to ischemic/reperfusion injury (IRI) often leading to HF. In this review, we compared the current in vivo, in vitro and ex vivo model systems used to study preeclampsia, IRI and HF. Future studies aiming at evaluating CVD in preeclampsia patients could benefit from novel models that better mimic the complex scenario described in this article.

The outbreak of COVID-19 is a public health emergency that caused disastrous results in many countries. The global aim is to stop transmission and prevent the spread of the disease. To achieve it, every country needs to scale up emergency response mechanisms, educate and actively communicate with the public, intensify infected case finding, contact tracing, monitoring, quarantine of contacts, and isolation of cases. Responding to an emergency requires efficient collaboration and a multi-skilled approach (medical, information, statistical, political, social, and other expertise), which makes it hard to define one interface for all. As actors from different perspectives and domain backgrounds need to address diverse functions, the possibility to exchange available information quickly would be desirable. Geoportal provides an entry point to access a variety of data (geospatial data, epidemiological data) and could be used for data discovery, view, download, and transformation. It helps to deal with challenges like data analysis, confirmed cases geocoding, recognition of disease dynamics, vulnerable groups identification, and capacity mapping. Predicting and modeling the spread of infection, along with application support for communication and collaboration, are the biggest challenges. In response to all these challenges, we have established the Epidemic Location Intelligence System (ELIS) using open-source software components in the cloud, as a working platform with all the required functionalities.

Blade Health Monitoring (BHM) is often necessary in power plants and in aviation to prevent excessive blade vibration and cracks. This article proposes a network of blade tip timing sensors operated in a distributed BHM system. A number of cooperating agents is implemented in smart conditioning units which can autonomously operate in an adverse environment and communicate with other nodes via a serial interface. The project uses special versions of reduced instruction set chips that are able to operate near the hot section of the engine. Due to the limited number of types of microprocessors available in the extended temperature range grading, it was necessary to fully utilize the limited hardware resources and implement preemptive multitasking. For this purpose, a custom operating system and communication protocol were designed. The protocol hosts the middle layer which hides the implementation of the distributed system. The presented architecture ensures the sufficient computational capacity in individual nodes of the network operated in adverse conditions. It is scalable and resistant to transmission errors.

The separation of rare earth metals (REM) from a neodymium magnet has been widely studied in the last year. We have shown that the waste of computer hard disk contains 25.41 % neodymium, 64.09 % iron, and &lt;&lt;1 % boron. To further isolate rare-earth metals, the magnet was acidically dissolved in open and closed systems. In both methods of dissolution was used concentrated nitric acid. The difference between these methods are the conditions of dissolution of magnet. The magnet was dissolved in a microwave sample preparation system at different temperatures and pressures in a closed system. In the open system, the acid dissolution of the magnet conducted at room temperature. 0.2 g of the neodymium magnet sample was taken under two conditions, and the dissolution process in the closed system lasted 1 hour, and in the open system-30-40 minutes. The open system is a non-laborious, simple and cheap method of dissolving the magnet by comparing both systems. Therefore, an open sample preparation system is used for further work. To remove the iron in the magnet, oxalic acid was used and precipitated as oxalates under both conditions. According to the result of the ICP-MS method, it is shown that the neodymium and iron contents in the precipitate are 24.66 % and 0.06 %, respectively. This shows that the iron has almost completely passed to the filtrate. Thus, it is possible to remove the iron from the sample.

It is proposed that the primary living cells (“probionts”) cannot emerge of organic substance simply by continuous chemical complication of prebiotic macromolecules and microsystems. The complication must be accompanied by the radical thermodynamic transformation (“jump”) of prebiotic microsystems that resulted in the acquired ability to extract free energy from the environment and export entropy. This transformation is called “the thermodynamic inversion” The inversion may occur by means of the efficient (intensified) response of the microsystems on the oscillations of physic-chemical parameters in hydrothermal environment. In this case the surplus available free energy within a microsystem, when combined with the informational modality, facilitates its conversion into a new microsystem—a living probiont. It is shown the schematic representation of an oscillating prebiotic microsystem that is transforming into a living probiont. A new kind of laboratory and computational experiments on prebiotic chemistry under oscillating conditions is offered to verify the inversion concept.

The present paper deals with the retrofitting of unreinforced masonry (URM) buildings, subjected to in-plane shear and out of-plane loading when struck by an earthquake. After an introductive comparison between some of the latest punctual and continuous active retrofitting methods, the authors focused on the two most effective active continuous techniques, the CAM system and the Φ system, which also improve the box-type behavior of buildings. These two retrofitting systems allow us to increase both the static and dynamic load-bearing capacity of masonry buildings. Nevertheless, information on how they actually modify the stress field in static conditions is lacking and sometimes questionable, in the literature. Therefore, we performed a static analysis in the plane of Mohr/Coulomb, with the dual intent to clarify which of the two is preferable under static conditions and whether the models currently used to design the retrofitting systems are fully adequate.

The United Arab Emirates (UAE) is significantly dependent on desalinated water and groundwater resource, which is expensive and highly energy intensive. Despite the scarce water resource, only 54% of the recycled water was reused in 2015. In this study, an “Oasis” complex comprised of Sustainable Farming Compartments (SFCs) was proposed for reusing treated wastewater to decrease the ambient temperature of the SFC via an evaporative cooling system. A prototype SFC with half the original scale (width = 1.8 m, depth = 1.5 m, front height = 1.2 m back height = 0.9 m) was designed, built, and tested in an environmentally controlled laboratory and field site to evaluate the feasibility and effectiveness of the SFC under the climatic conditions in Abu Dhabi. Based on the experimental results, the temperature drops obtained from the SFC in the laboratory and field site were 5 ̊C at initial relative humidity of 60% and 7- 15 ̊C at initial relative humidity of 50%, respectively. An energy simulation using dynamic numerical simulations was performed in comparison to the results of the experiment. The energy-based dynamic simulation shows good agreement with the experimental results. The total power consumption of the SFC system was approximately three and a half times lower than that of an electrical air conditioner.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

Global warming is one of the problems of human civilization and decarbonization policy is the main solution to this problem. In this work, we propose an alternative method of using the gravity-assist by the asteroids to increase the orbital distance of the Earth from the Sun. We can manipulate the orbit of asteroids in the asteroid belt by solar sailing and propulsion engines to guide them towards the Mars orbit and a gravitational scattering can put asteroids in a favorable direction to provide an energy loss scattering from the Earth. The result would be increasing the orbital distance of the earth and consequently cooling down the Earth’s temperature. We calculate the increase in the orbital distance of the earth for each scattering and investigate the feasibility of performing this project.

IT auditing quality has been defined by results obtained in the process. Meanwhile, multiple studies have been done to enhance it therefore, it continues to be a topic interest and research so it is worth mentioning that its quality relies on trained competent auditors and experts able to develop a process correctly, adapting to clients and to manage auditing inherent risks According to results from the IT audit, low quality and security levels have been identified in terms of the human, technical and contextual factors, affecting audit quality. The objective of this investigation is to identify metrics and to determine their own corresponding factor applying an exploratory type of research. In order to achieve such aim, a targeted survey was designed and implemented at the Institute of Internal Auditors of Ecuador since they have the knowledge and expertise in the field. A factor analysis statistics technique was applied to data gathered to verify that it relates to the identified factors as dimensions are reduced, thus the most impacting metrics may assess the quality of IT audits. Analysis results yielded a mean score for each one of the assessed metrics, concluding that the technical factor is the most significative since it relates roles and task performance during the auditing process as well as control proce-dures. Finally, most auditing quality-related issues are mainly the outcome of an inferior management auditing process, therefore it is crucial that collegiate groups and professionals in the field validate the auditing process.

In the Republic of Serbia, no comprehensive scientific multimethod research has been conducted to identify weaknesses and opportunities for improving the disaster risk management system. Regarding that, in the paper, author presents project description ,,Strengthening Integrated Disaster Risk Management System in Serbia - DISARIMES” which shall enable strengthening the disaster risk management system through research, development and innovative solutions implementation in the preparation, mitigation, response, remediation and post-disaster phases. The scientific importance of the projected research is reflected in the creation of assumptions for the advancement of theoretical and empirical knowledge in the scientific field of disaster risk management, bearing in mind that it is a relatively young scientific discipline in Serbia. The results of the project research will make it easier for decision makers in Serbia to understand the shortcomings of the system, but also provide innovative opportunities to improve their functioning in conditions of increasingly frequent and serious disasters. Establishing a scientific and professional society in the field of disaster risk management will create sustainable and necessary conditions for the transfer and improvement of knowledge and experience of importance for raising the level of operability of the system of protection and rescue of the Republic of Serbia in the event of disasters. A key contribution of the research findings will be to create a sustainable knowledge base that will be supported by the relevant amount of information regarding innovative capabilities and solutions identified as necessary to raise social resilience to a much higher level. In order to achieve the set goals, DISARIMES makes it possible, through a large number of SWOT analyses and other multimethod studies, to clearly identify and systematize the objective deficiencies and barriers encountered by the disaster risk management system in Serbia in all its stages before, during and after disasters, to identify and implement the appropriate solutions based on this. The objectives of the project are: to assess and identify strengths (advantages), weaknesses (disadvantages), opportunities (innovation potential) and threats for the disaster risk management system in Serbia; to develop and update RDI (research, development, innovation) Roadmap – knowledge databases with innovative solutions and other relevant information for improvement of the disaster risk management system; to fully deploy the DISARIMES scientific-professional network involving a broad range of the disaster risk management scientists and civil protection professions and organisations; to prepare the ground for the disaster risk management policy innovations.

This review summarizes the use of CRISPR system in yeasts, identifying advantages and disadvantages of its applications. 39 articles were evaluated including 12 articles that discussed the advantages of new CRISPR systems that improved the initial system, and another 27 were evaluated, among these: three were applications in Cryptococcus neoformans, four in candida sp., three in Schizosaccharomyces pombe, nine in Saccharomyces cerevisiae, four in Yarrowia lipolytica, and four in industrially important yeasts such as Pichia pastoris and Saccharomyces pastorianus. It was concluded that the CRISPR system is one of the most versatile genetic editing systems available nowadays. It can be applied in different organisms for several effects including gene knock-outs, performing point mutations, gene expression, or even applying multiple edition operations in several genes. However, we recognize that numerous studies lack a control group of the mutated strains, which leaves many questions unanswered. For instance, the extent and precision of this techniques, it also represents a risk to biosecurity standards. Therefore, this review shows the compilation of CRISPR system information, which could be used to generate different alternatives in the industry and clinical fields.

In two dimensional disordered lattices, presence of interaction makes particles less localized than the non-interacting ones within the range of disorder strength W ≤ 4 and interaction strength V ≤ 4. If the interaction strength is higher, then particles localize more. Although, a localization-delocalization transition is not found, a transition with changes in the dominant correlations is observed. The nature of correlations between the particles as nearest neighbors become dominant beyond certain disorder strengths.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

The accurate of model attitude angel plays an important role on the aerodynamic test results in the wind tunnel test. The original method applies the spherical coordinate system transformation to obtain attitude angel calculation. The model attitude angel is obtained by coordinate transformation and spherical surface mapping applying the nominal attitude angel (the balance attitude angel in the wind tunnel coordinate system) indicated by the mechanism. First, the coordinate transformation of this method is not only complex but also difficult to establish the transformed relationship between the space coordinate systems especially after many steps of coordinate transformation, moreover it cannot realize the iterative calculation of the interference relationship between attitude angels; Second, during the calculate process to solve the problem the arc is approximately used to replace the straight line, the angel for the tangent value, and the inverse trigonometric function is applied. Therefore, in the calculation of attitude angel, the process is complex and inaccurate, which can be solved approximately when calculating small attack angel. However, with the advancing development of modern aerodynamic unsteady research, the aircraft tends to develop high or super large attack angel and unsteady research field. According to engineering practice and vector theory, the concept of vector angel coordinate system is proposed for the first time, and the vector angel coordinate system of attitude angel is established. With the iterative correction calculation and avoiding the problem of approximate and inverse trigonometric function solution, the model attitude calculation process is carried out in detail, which validates that the calculation accuracy and accuracy of model attitude angels are improved. Based on engineering and theoretical methods, a vector angel coordinate system is established for the first time, which gives the transformation and angel definition relations between different flight attitude coordinate systems, that can accurately calculate the attitude angel of the corresponding coordinate system and determine its direction, especially in the channel coupling calculation, the calculation of the attitude angel between the coordinate systems is only related to the angel, and has nothing to do with the change order s of the coordinate system, which simplifies the calculation process.

Open Inertia Modelling (OpInMod) is a modelling framework designed to create unit commitment and economic inertia dispatch optimisation problems. Present energy system modelling generators do not consider power system inertia in unit commitment and economic dispatch modelling to assess future energy system pathways. However, maintaining sufficient power system inertia in power systems is the foundation for power frequency controllability. The work at hand describes the functionality and approaches of open source tool OpInMod. The softwares universal design approach increases reuse potential. OpInMod is distributed with a set of examples to test and understand OpInMod

The present study compared the contralateral suppression and the amplitude of distortion product otoacoutsic emissions (DPOAEs) between smokers and non-smokers to determine the influence of smoking. Thirty smokers and thirty non-smokers within the age range of 18-40 years with a normal hearing sensitivity were considered for the study. For both the groups, DPOAEs were measured and the efferent auditory system functioning was measured by presenting the white noise of 50 dB HL to the contralateral side, while recording the DPOAEs. There was no significant effect of age on the amplitude of DPOAEs in both the groups. However, there were significant differences in the amplitude of DPOAEs between smokers and non-smokers. The amount of suppression and DPOAE amplitude were reduced in smokers when compared to non-smokers. The study found no significant correlation between the amount of smoking and amount of suppression between smokers and non-smokers. However, there were significant correlations between the amount of smoking and DPOAE at low and mid frequencies between smokers and non-smokers. Therefore, the present study highlights the increased damage to the efferent auditory system risk and the smoking ill-effects on the efferent auditory system.

This study aims to develop a performance evaluation system that can facilitate performance evaluation at region, hospital, and department levels to enable better cost management for sustainable development. A multi-level system of performance evaluation informs a hierarchical assessment of cost management from regions to hospitals to departments using diagnosis-related group (DRGs). Various metrics are developed employing the variances between targets and actuals where targets are determined from two perspectives: benchmarking using external regional prices and change management using internal data. Targets for the latter are statistically based and specifically incorporate variability. The model is applied to two hospitals, twenty departments, nine DRGs and 1071 inpatients. The analyses indicate that the approach can provide a practical evaluation tool that allows for particular characteristics at multiple levels. The system provides macro-micro and external-internal perspectives in performance, enabling high-level variances to be decomposed thereby identifying sources of performance variability and financial impact.

The article presents a new approach to the analysis of the stability of automatic systems with discrete links.In almost all modern automatic control systems, there are links that break signals in time. These are power controlled switches - transistors or thyristors operating in a pulsed mode and digital links in regulators.Time discretization significantly affects the stability of processes in the automatic control system. The theoretical analysis of such systems is rather complicated and requires a significant change in engineering approaches to analysis. In connection with the improvement of digital controllers and a significant increase in their performance, in recent years this problem has practically not been remembered. However, its mathematical "content" has not changed since the 80s of the 20th century, when discreteness began to play a major role among the problems hindering progress in automatic control systems, in terms of the transition to digital systems.In this paper, a new approach is proposed, which consists in interpreting the sampling operation by a link with the proposed frequency characteristic, which determines the suppression of input high-frequency signals. This link greatly simplifies engineering calculations and demonstrates the new capabilities of sampling systems. These possibilities include the rational distribution of digitalization resources - the number of bits and the sampling interval between the regulator channels, depending on the frequency range of the efficiency of these channels. Theoretical statements have been verified and confirmed by simulation. It is shown how this approach makes it possible to formulate new principles of construction of seemingly well-known controllers - PID controllers and variable structure systems (VSS).

Sector coupling is one of the emerging topics in recent energy and climate change policy discussions. It can play a significant role in creating the pathway of a renewable-based energy system in the European energy sector. The North Sea region is very likely to play a key role in the transition to a sustainable energy system. Though different energy modelling approaches allow a versatile use, they lead to the problem of an unclear understanding of specific aspects of sector coupling, and the relevance of existing tools and techniques to model and analyze such a system. This paper is aimed at providing a comprehensive understanding of sector coupling and its incorporation in energy system models. Followed by a thorough literature review on sector coupling and energy system modelling, the paper outlines an approach to select an appropriate tool based on the specific rationales of the research. The paper also presents ‘Oemof’ as an open model tool to address the complex challenges of energy systems. The conclusions from the literature review provide a detailed understanding of the concept of sector coupling and indicate that it can be advantageous from the viewpoints of decarbonization, flexibility, network optimization, and system efficiency. To solve the coupling barriers, diversified techno-socio-economic circumstances should be taken into account through the use of model collaboration. It is also demonstrated how a list of appropriate tools for model collaboration can be picked up methodologically from an available wide range of models. Finally, ‘Oemof’ is hypothesized as a progressive tool to design a sector-coupled and renewable-based energy system in the North Sea region.

We present a new unsupervised method aimed to obtain a partition of a complex urban system in homogenous urban areas, called urban contexts. The area of study is initially partitioned in microzones, homogeneous portion of the urban system, that are the atomic reference elements for the census data. With the contribution of domain experts, we identify the physical, morphological, environmental and socio-economic indicators need to identify synthetic characteristics of urban contexts and create the fuzzy rule set necessary to determine the type of urban context. We implement the set of spatial analysis processes necessary to calculate the indicators for microzone and apply a Mamdani fuzzy rule system to classify the microzones. Finally, the partition of the area of study in urban contexts is obtained by dissolving continuous microzones belonging to the same type of urban context. Tests are performed on the Municipality of Pozzuoli (Naples - Italy); the reliability of out model is measured by comparing the results with the ones obtained by detailed analysis.

Bisphenol A production plant possesses considerable potential risks in the top of the methanol separation column, as pressurized acetone, methanol and water are processed at an elevated temperature, especially in the event of an abnormal pressure increase due to sudden power outage. This study assesses the potential risks in the methanol separation column through hazard and operability assessment and evaluates the damages in the case of fire and explosion accident scenarios. The study chooses three leakage scenarios: a 5-mm puncture on the methanol separation column, a 50-mm diameter fracture of a discharge pipe and a catastrophic rupture, and simulates using Phast (Ver. 6.531) the concentration distribution of scattered methanol, thermal radiation distribution of fires and overpressure distribution of vapor cloud explosions. Implementation of safety instrumented system equipped with two-out-of-three voting as a safety measure can detect overpressure at the top of the column and shut down the main control valve and the emergency shutoff valve simultaneously, all at the same time. By applying safety integrity level of three, the maximal release volume of the safety relief valve can be reduced and therefore, the design capacity of the flare stack can also be reduced. Such integration will lead to improved safety at a reduced cost.

Human number understanding is thought to rely on the analogue number system (ANS), working according to Weber’s law. We propose an alternative account, suggesting that symbolic mathematical knowledge is based on a discrete semantic system (DSS), a representation that stores values in a semantic network, similar to the mental lexicon or to a conceptual network. Here, focusing on the phenomena of numerical distance and size effects in comparison tasks, first we discuss how a DSS model could explain these numerical effects. Second, we demonstrate that DSS model can give quantitatively as appropriate a description of the effects as the ANS model. Finally, we show that symbolic numerical size effect is mainly influenced by the frequency of the symbols, and not by the ratios of their values. This last result suggests that numerical distance and size effects cannot be caused by the ANS, while the DSS model might be the alternative approach that can explain the frequency-based size effect.

A single Information security is of pivotal concern for consistently streaming information over the widespread internetwork. The bottleneck flow of incoming and outgoing data traffic introduces the issue of malicious activities taken place by intruders, hackers and attackers in the form of authenticity desecration, gridlocking data traffic, vandalizing data and crashing the established network. The issue of emerging suspicious activities is managed by the domain of Intrusion Detection Systems (IDS). The IDS consistently monitors the network for identifica-tion of suspicious activities and generates alarm and indication in presence of malicious threats and worms. The performance of IDS is improved by using different signature based machine learning algorithms. In this paper, the performance of IDS model is determined using hybridization of nestrov-accelerated adaptive moment estimation –stochastic gradient descent (HNADAM-SDG) algorithm. The performance of the algorithm is compared with other classi-fication algorithms as logistic regression, ridge classifier and ensemble algorithm by adapting feature selection and optimization techniques

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

This venture targets giving a correspondence framework that can improve the legal framework execution and cooperation and furthermore make it simple to lead execution audits. This examination depicts restricted admittance to the right legitimate data just as admittance to courts and court administrations as the essential factors that limit admittance to equity. The basic target fundamental for accomplishing the point incorporates planning an online easy to understand data framework that would improve correspondence and association between legal professionals like legal advisors and disputants. The undertaking uses a subjective methodology that zeroed in on the substance investigation of essential information. Key members were court laborers like attorneys and agents, just as court clients like disputants. Pre-plan discoveries uncovered that current legitimate data frameworks – basically court sites – neglect to recognize their crowd by treating all court clients similarly comparative with the correspondence of lawful data. Likewise, the issue of admittance to equity includes the significant expense of equity also, restricted legal data that elevates admittance to equity. Post-plan discoveries from the online overview directed after the turn of events and execution of the IT curio uncovered a powerful and productive legitimate data framework. Exploration discoveries supported the advancement of an IT antiquity that records for huge shortcomings in current legal data frameworks, for example, their failure to pass on fitting legitimate data intelligently and productively. In outline, the investigation prescribes the reception of saw control to work fair and square of certainty of court clients and the differentiation between court clients to convey the right data to the right crowd.

In all areas of medicine, especially in radiology, computers are increasing year by year. Filmless radiology, speech recognition software, electronic application forms, and teleradiology are recent developments that have greatly improved radiologists' performance. This research explores radiology software trends, predictions, and the challenges posed by informatics and historical trend analysis. The rationale behind this research is that information technology (IT) is overgrowing almost every day. We must continuously seek new ways to apply IT to make more use of resources. Consequently, IT becomes increasingly crucial to radiology organizations' innovative thinking, workflow, and business models. This study aimed to analyze all radiology software publications in the Science Citation Index (SCI). From 1991 to July 2021, SCI was used to search for publications systematically. We have also widely used this historical method in radiology software research. The findings and discussions are base on an assessment of trends, predictions, contributions, and challenges in radiology software, and we are exploring radiology software with six evolutionary stages. The gift of this research is that radiology managers realize that the use of new information technologies is closely related to survival in a competitive environment. Radiology companies can review these new technologies to develop more innovative business models and services to improve operational deficiencies.

This paper proposes a method for determining the bridge condition index (BCI) in concrete bridges, which is based on the views of bridge experts. First, eight indices were defined for a concrete bridge including structure, hydrology, safety, load impact, geotechnical and seismicity, strategic importance, facilities, and finally traffic and pavement. Each index consists of several sub-indices. Next, a series of questionnaires about the relative importance of indices and their sub-indices were prepared and distributed among bridge experts. Experts’ views were analyzed by Expert Choice software and the relative importance (weight) of each index and each sub-index was determined using the analytical hierarchy process (AHP). Then, based on experts’ views, an average score was assigned to each sub-index for any condition. Now the bridge inspectors can examine the bridge and determine the scores of sub-indices. Each index’s score is the sum of the weighted score assigned to its’ sub-indices and BCI is the sum of weighted scores assigned to indices. Higher values of BCI indicate a better condition. Therefore, bridges with lower BCI take priority in maintenance activities. To apply the proposed method, five bridges were selected in Semnan province, Iran, and BCI calculation of these bridges were conducted.

The voice contains elementary social communication cues, conveying speech, as well as paralinguistic information pertaining to the emotional state and the identity of the speaker. In contrast to vocal-speech and vocal-emotion processing, voice-identity processing has been less explored. This seems surprising, given the day-to-day significance of person recognition by voice. A valuable approach to unravel how voice-identity processing is accomplished is to investigate people who have a selective deficit in recognising voices. Such a deficit has been termed phonagnosia. In the present chapter, we provide a systematic overview of studies on phonagnosia and how they relate to current neurocognitive models of person recognition. We review studies that have characterised people who suffer from phonagnosia following brain damage (i.e. acquired phonagnosia) and also studies, which have examined phonagnosia cases without apparent brain lesion (i.e. developmental phonagnosia). Based on the reviewed literature, we emphasise the need for a careful behavioural characterisation of phonagnosia cases by taking into consideration the multistage nature of voice-identity processing and the resulting behavioural phonagnosia subtypes.

A tabletop system can facilitate multi-user collaboration in a variety of settings including small meetings, group work, and education and training exercises. The ability of identifying the users touching the table and their positions can promote collaborative work among participants, so methods have been studied that involve the attaching of sensors to the table or chairs or to the users themselves. An effective method of recognizing user actions without placing a burden on the user would be some type of visual process, so the development of a method that processes multi-touch gestures by visual means is desired. This paper describes the development of a multi-touch tabletop system using infrared image recognition for user position identification and presents the results of touch-gesture recognition experiments and a system usability evaluation. Using an FTIR touch panel and infrared light, this system picks up the shadow area of the user’s hand by infrared camera in relation to user touch operations and estimates user position by image recognition. The multi-touch gestures prepared for this system include an operation to change the direction of an object to face the user and a copy operation in which two users generate duplicates of an object. The average recognition rate of the change-direction gesture and copy gesture were found to be 96% and 85%, respectively. In addition, the system usability evaluation revealed that prior learning was easy and that system operations could be easily performed.

Unusual outbreak of Covid 19 has put the whole new challenges around the globe. In a short span of time, the world has been changed, lifestyles, social events, cultural, political events everything has been put on hold as number of countries has enforced partial or complete lockdown that resulted positive in context of controlling spread and contamination of COVID-19. Such activities have also put some effects on environment in both positive and negative way. In this study only positive impacts of COVID-19 on Environment have been highlighted that played role in regeneration of natural systems i.e., reduced air emissions, cleaner air, beaches &water bodies, reduced noise levels, biodiversity rehabilitation etc.

This article addresses a challenge modeling novices face in model conceptualization: the recognition of behavior modes. Despite behavior modes being at the heart of system dynamics modeling, there is no unifying taxonomy for them, making them harder to learn for beginners. The article proposes criteria a taxonomy should satisfy, critically reviews previous taxonomies in the literature, and then introduces a new consistent taxonomy based on slope and curvature with mode names that refer only to visual cues and free of references to prior mathematical or domain-specific knowledge. Evidence from an exploratory experiment suggests that novices actually have difficulties classifying curves when using previous taxonomies. Links from these elementary modes to analogous terms in other taxonomies in diverse disciplines allow this taxonomy to be related to other ones. The article concludes by mentioning relevant limitations and future steps.

This paper aims to investigate the rate of expansion and extraction within the solar system. We carried out the Solar system expansion calculations to do such a review. The Universe is expected to look the same from every point in it. After the big bang, Universe is expanding at some speed. Astrophysicists have been in a race to measure precisely how fast the Universe is expanding since Hubble announced that galaxies were systematically moving away from Milky Way Galaxy with a current speed in 1929. Hubble’s observations came after Einstein’s general relativity, which inspired the big bang theory. According to the Big Bang theory, the Universe has created billions of years ago with an explosion and started to expand until today. The expansion of the Universe mostly happens in vast spaces, so clusters of galaxies move away from each other. For example, raising bread during baking will expand, but the raisings will stay the same size while moving each other to expand the bread. Observers have proven that an object (galaxies, a cluster of planets) held together by gravity has a patch of nonexpanding space produced by a gravitational field. However, some observers claimed the solar system is not expanding, while others claimed it is expanding. Does our solar system expand in an expanding Universe? The cosmological expansion of local systems is reviewed in the modern cosmological models. We showed answers related to this question with the help of literature. This review article revisited the proof of the Solar System’s expansion and its speed with about 0.32 nm/s in an expanding Universe.

Background: The practices of various health-care professionals have been improvised to accommodate the on-going covid-19 pandemic situation. Different guidelines have been set in place to ease the process of re-opening of non-elective healthcare services like out-patient physiotherapy clinics. Although the measures taken should be guided by evidence based information, major consensus amongst practicing therapists needs to guide the India physiotherapy clinics. Objective: To identify and present the opinions of different physiotherapists about the various strategies for re-opening the out-patient physiotherapy clinics. Methods: An online cross-sectional survey was conducted. Over 169 participants were selected to participate in the survey according to the pre-decided inclusion and exclusion criteria. The data was collected and saved via google forms. Result and conclusion: A majority of respondents had a consensus over different strategies for re-opening the physiotherapy OPDs. These were regarding different measures to be adapted including modifications in the clinic infrastructure and the practice pattern. This would help in smoothly re-instating the physiotherapy services post the covid-19 lockdown.

A spinning gyroscope precesses about the vertical due to a torque acting upon the wheel. The torque is generated by the shift of moment of force by gravity and it points to the vertical instead of the tangential direction of precession. This intuition offers an alternative and straightforward view of precession dynamics in comparison with the literature. It also presumes a dynamic balance of momentum between circular motions of the wheel spin and precession. Accordingly, the gyroscopic dynamics is then applied to the study of galactic motion of the solar system in space and the Galactic mass is calculated with the inclusion of gyroscopic effect of the solar planets. Results indicate that the gyroscopic effect of Mercury orbiting around the Sun can increase the calculated Galactic mass by 23% in comparison with the result obtained by the classic approach.

β-glucan is a generic term for insoluble dietary fibers exerting various effects on the immune system. As a group, β-glucans are non-cellulose polysaccharides composed of a glucopyranose as the main constituent sugar with β configuration, having a β- (1,3)-linked glucopyranose main chain as a common feature. β-glucans are absorbed through the intestine. Since the 1980s, there have been many studies reporting various effects of β-glucans on the immune system, including reports on receptors, that have slowly clarified their recognition system and action mechanisms. However, these studies focused mostly on treatments of infectious diseases and tumors; thus, the effects of β-glucans ingested in food as dietary fiber and their mechanisms of action remain largely unknown. The uptake of β-glucan into the body may be resemble that of proteins, which are soluble polymers, and insoluble material such as dietary fiber. Dietary fibers have varied structures, with wide-ranging solubility and physiological effects. Understanding whether these substances are actually taken up, how they exert their effects, and their metabolism after being taken up are important issues when considering the functionality and safety of dietary fibers.

In the same manner that there are several statements of the second law of thermodynamics but all of them are equivalent, it is possible that most of the entropic methods applied to the nervous system and brain in particular share a similar outcome, or essence, that helps understand some aspects of the fundamentals of basic neurodynamics. In this short review focused on certain aspects of the entropic metrics some results are examined that indicate the fundamental importance of the natural tendency towards a maximal energy distribution for healthy brain activity and thus cognition to emerge.

A nuclear reactor leak is undesirable and unpredictable occurrence in the plant of nuclear energy generation. For this reason, an accurate equipment is needed to inspect and supervise reactors. There are two kind of reactors for research and industry reactors, both of them are needed to inspect. Concern to inspection, regularly check is needed to ensure reactor conditions are always safe to operate. For that reason, an application of advanced technology for detecting leaks is priority. In this research, we are using underwater robot to be implemented. Using the robot is able to detect periodically, continuously with accurate reports to the operator or reactor supervisor. Furthermore, Underwater Robot namely Robaru, with 4 propellers equipped at the robot, Robaru can move on 3 axes x, y and z and rotate. The use of cameras, as well as temperature measurements to obtain data when conducting inspections of the reactor. The survey method used is direct observation to detect leaks. The robot is at a certain distance by following a predetermined connection or path. The robot has successfully performed a good check with an accurate level of positioning accuracy.

Chronic high glucose (HG) exposure increases methylglyoxal (MG)-derived AGEs and is involved in the onset of pathological conditions, such as diabetes, atherosclerosis and chronic‐degenerative diseases. Under physiologic condition the harmful effects of MG are contrasted by glyoxalase system that is involved in the detoxification of Reactive Carbonyl Species (RCS) and maintain the homeostasis of the redox environment of the cell. Polyphenols are the most abundant antioxidants in the diet and present various health benefits. The study aimed at investigating the role of polyphenols extracted from an apple high in polyphenols (Calville White Winter), on glyco-oxidative stress induced by chronic HG-exposure. Intestinal Caco-2 cells were treated in physiological glucose condition (25mM) as a control and in HG condition (50mM) with or without apple extract for one week. Our data demonstrated that HG-treatment triggers glyco-oxidation stress with a significantly increase in ROS, lipid peroxidation, AGEs and Glyoxalase I (GlxI) activity with a significant decrease in total antioxidant intracellular defense. Treatment with polyphenols under HG condition restores to the control levels GlxI activity, decreases Glyoxalase II (GlxII) in relation to the control and induces a drop of glyco-oxidative damage. This paper seeks to highlight the roles of polyphenols in glyco-oxidative stress.

When a microgrid is grid-tied to a distribution system, it can provide surplus power generation to the distribution system, if any abnormality or interruption occurs in the distribution system, the microgrid can operate in standalone mode to isolate the impact of the abnormality or interruption. However, if the microgrid can not collect enough information from the distribution system, it may cause the failure of generation transferring of distribution feeders, or even further influence the stability of the distribution system. In this paper, a strategy for the resilient control of a microgrid is proposed. It can solve the above-mentioned problem, reduce the duration of the outage of loads. This strategy is experimented in the microgrid in the Institute of Nuclear Energy Research (INER), the reliability is also analyzed to evaluate the unavailability of the microgrid in INER, and it is verified that the proposed strategy can reduce the duration of the outage of loads, and hence the reliability of a microgrid can be upgraded.

Heart failure (HF) has several etiologies including myocardial infarction (MI) and left ventricular remodeling (LVR), but its progression remains difficult to predict in clinical practice. Systems biology analyses of LVR after MI predict molecular insights of this event such as modulation of microRNA (miRNA) that could be used as a signature of HF progression. To define a miRNA signature of LVR after MI, we use 2 systems biology approaches integrating either proteomic data generated from LV of post-MI rat induced by left coronary artery ligation or multi-omics data (proteins and non-coding RNAs) generated from plasma of post-MI patients from the REVE-2 study. The first approach predicts 13 miRNAs and 3 of these miRNAs were validated to be associated with LVR in vivo: miR-21-5p, miR-23a-3p and miR-222-3p. The second approach predicts 24 miRNAs among 1310 molecules and 6 of these miRNAs were selected to be associated with LVR in silico: miR-17-5p, miR-21-5p, miR-26b-5p, miR-222-3p, miR-335-5p and miR-375. We identified a signature of 7 microRNAs associated with LVR after MI that support the interest of integrative systems biology analyses to define a miRNA signature of HF progression.

Legionnaires’ disease is normally acquired by inhalation of legionellae from a contaminated environmental source. Water systems of large buildings, such as hospitals, are often contaminated with legionellae and therefore represent a potential risk for the hospital population. In this study, we demonstrated the constant presence of Legionella in water samples from the water system of a large university hospital in Messina (Sicily, Italy) consisting of 11 separate pavilions during a period of 15 years (2004-2018). In total, 1346 hot water samples were collected between January 2004 and December 2018. During this period, to recover Legionella spp. from water samples the standard procedures reported by the Italian Guidelines emanated in 2000 were adopted; from May 2015 to 2018 Italian Guidelines revised in 2015 (ISS, 2015), were used. The most water samples (72%) were positive to L. pneumophila serogroups 2-14 whereas L. pneumophila serogroup 1 accounted for the 18% and Legionella spp. for the 15%. Most of the positive samples were found in the buildings where are situated critical wards as ICU, Neurosurgery, Surgeries, Pneumology and Neonatal Intensive Unit Care. We highlighted the importance of a continuous monitoring of hospital water samples to prevent the potential risk of nosocomial legionellosis.

In the repercussions of the latest financial crisis that have occurred on the years 2008-2009, to fortify the stability of the banking systems, policy makers, and the Basel Committee on Banking Supervision – BCBS, together with national regulators have built up a few safety measures, and structures to guarantee that banks establishments keep up adequate capital levels through using risk management tools, in specific the Internal Capital Adequacy Assessment Processes (ICAAP). They all have called for thorough evaluations and assessments for the structure and components of risk management frameworks, tools, and practices whether by banks, regulators, analysts and risk management experts consistently, to ascertain the adequacy of the banking systems, policies, arrangements and techniques for overseeing risks, and guaranteeing the sufficiency of holding appropriate capital levels for confronting normal, as well as adverse and unexpected situations or emergencies. The main objectives of this research study is to shed the light on the ICAAP as one of the main keys of risk management programs, a process by which banks can use to ensure that they operate with an appropriate levels of capital, forward looking processes for capital planning covering a broad range of risks across banks, activities beyond simple capital management, and brings together risk and capital management activities in a form that can be used to support business decisions. The research study shall evaluate the significant relationship between the Banking System Stability (dependent variable) and the Internal Capital Adequacy Assessment Process (ICAAP – independent variable) with evidence from the Egyptian Banking Sector.

Conventional models do not fully explain composition of the solar system – for example, the presence of p-nuclei and post-post-Fe-nuclei remains not yet understood (and is one of the great unresolved puzzles of nuclear astrophysics in general); other puzzles exist. We offer a hypothesis which can explain the appearance of non-native elements in the solar system, and a feasible scenario for its implementation. The hypothesis suggests that a nuclear-fission "event" occurred in the inner part of the solar system at the time currently defined as the birth of the system. Conventional models have never considered fission as a contributing nuclei-production mechanism. Upon examination of the existing models and factual data (presented in volumes of publications but never combined into an aggregate), we identified one plausible scenario by which a fission event (not demolishing the entire solar system) could occur: an encounter with a compact super-dense stellar "fragment" (with specific properties) and its "explosion" in fission-cascades. Such scenario also helps resolve other long-standing puzzles of the solar system. For example, it provides that the fission-produced nuclei subsequently transformed into the material that (eventually) accreted into the "rocky" objects in the system (terrestrial planets, asteroids, etc.) and enriched the pre-existed hydrogen-helium objects (the Sun and the gaseous giants) – this offers an explanation for the planets’ inner position and compositional differences within the predominantly hydrogen-helium rest of the solar system. Other implications also follow.

Present paper is dealing with the adaptive static balancing of robot or other mechatronic arms that are moving in vertical plane and whose static loads are variable, by using counterweights and springs. Some simple passive and approximate solutions are proposed and an example is shown. The active and exact solutions by using adaptive real time control in the case of unknown variation of static loads are simulated on VIPRO platform developed at Institute of Solid Mechanics of Romanian Academy.

Microbolometer is the most common uncooled infrared technique that allows to achieve 50mK-temperature resolution on the scene. However, this approach has to struggle with both the self-heating inherent to the resistive readout principle and the 1/f noise. We present an alternative approach that consists in using micro / nanoresonators vibrating according to a torsional mode, and whose resonant frequency changes with the incident IR-radiation. Dense arrays of such electromechanical structures were fabricated with a 12µm-pitch at low temperature allowing their integration on CMOS circuits according to a post-processing method. H-shape pixels with 9 µm-long nano-rods and a cross-section of 250 × 30 nm² were fabricated to provide large thermal responses, whose experimental measurements reached up to 1024 Hz/nW. These electromechanical resonators featured a noise equivalent power of 140pW for a response time of less than 1 ms. To our knowledge, these performance are unrivaled with such small dimensions. We also showed that a temperature sensitivity of 20 mK within 100ms-integration time is conceivable at a 12µm-pitch by co-integrating the resonators with their readout electronics and suggesting a new readout scheme. This sensitivity could be reached at short-term by depositing on top of the nano-rods a vanadium oxide layer having a phase-transition that could possibly enhance the thermal response by one order of magnitude.

In nonlinear self-consistent system, Lorenz system (Lorenz equations) is a classic case with chaos solutions which are sensitively dependent on the initial conditions. As it is difficult to get the analytical solution, the numerical methods and qualitative analytical methods are widely used in many studies. In these papers, Runge-Kutta method is the one most often used to solve these differential equations. However, this method is still a method based on explicit time scheme, which would be the main reason for the chaotic solutions to Lorenz system. In this work, numerical experiments based on implicit time scheme and explicit scheme are setup for comparison, the results show that: in implicit time scheme, the numerical solutions (counterexamples) are without chaos; for an original volume, the volume shrinks exponentially fast to 0 in common.

Energy system models have become indispensable to shape future energy systems by providing insights into different trajectories. However, sustainable systems with high shares of renewable energy are characterized by growing cross-sectoral interdependencies and decentralized structures. To capture important properties of increasingly complex energy systems, sophisticated and flexible modelling tools are needed. At the same time open science becomes increasingly important in energy system modelling. This paper presents the Open Energy Modelling Framework (oemof) as a novel approach in energy system modelling, representation and analysis. The framework forms a toolbox to construct comprehensive energy system models and has been published open source under a free license. With a collaborative development based on open processes the framework seeks for a maximum level of participation and transparency to facilitate open science principles in energy system modelling. Based on a generic graph based description of energy systems it is well suited to flexibly model complex cross-sectoral systems and incorporate various modelling approaches. This makes the framework a multi-purpose modelling environment for modelling and analyzing different systems ranging from an urban to a transnational scale.

In recent years, there have been concerns raised about construction industrialization in China, which have initiated a wave of policy change in both governmental and industrial organizations in order to change the mode of conventional construction. However, the current development level of regional construction industrialization (RCI) in China has not been well-characterized. This study screened preliminary index systems in five dimensions: technical, economic, sustainable, enterprise development and development environment. Based on the data gathered from the questionnaire surveys and subsequently analyzed, twenty-two critical evaluation indicators were identified. Analytic Hierarchy Process (AHP) was then employed to determine the weighting of each indicator. The evaluation method of the development level was formulated on the basis of the evaluation criteria. Jiangsu Province was used as an example in this study, with the development level of this province being comprehensively examined using a combination of the index system and evaluation method. The results show that Jiangsu has a relatively high RCI development level. The data from analysis scores of five dimensions and twenty-two indicators show that the index system is feasible, with evaluation results being consistent with actual practice. These findings provide a good practical reference for making decisions about how best to guide the development of RCI.

The article describes how atherosclerosis and coronavirus disease 19 (COVID-19) may affect each other. The features of this comorbid pathogenesis at various levels (vascular, cellular and molecular) are considered. A bidirectional influence of these conditions is described: the presence of cardiovascular diseases affects different individual susceptibility to viral infection. In turn, SARS-CoV-2 can have a negative effect on the endothelium and cardiomyocytes, causing blood clotting, secretion of pro-inflammatory cytokines, and thus exacerbating the development of atherosclerosis. In addition to the established entry into cells via ACE2 принимая во внимание его влияние на, other mechanisms of SARS-CoV-2 entry are currently under investigation, for example, through CD147. Pathogenesis of comorbidity can be determined by the influence of the virus on various links which are meaningful for atherogenesis: generation of oxidized forms of LDL, launch of a cytokine storm, damage to the endothelial glycocalyx, and mitochondrial injury. The transformation of a stable plaque into an unstable one plays an important role in the pathogenesis of atherosclerosis complications and can be triggered by COVID-19. The impact of SARS-CoV-2 on large vessels such as aorta is more complex than previously thought considering its impact on vasa vasorum. Current information on the mutual influence of the medicines used in the treatment of atherosclerosis and acute COVID-19 is briefly summarized

This paper attempts to describe the large-scale (solar system-like, astronomical-scale) systems of the known world using the physical models and mathematical tools of relativistic quantum mechanics. The value of H_x can be introduced and approximated as an analogue of the constant ℏ. Based on the quantum mechanical approach, the proper time scale of the solar system can be determined.

Based on measured astronomical position data of heavenly objects in the Solar System and other planetary systems, all bodies in space seem to move in some kind of elliptical motion with respect to each other. According to Kepler’s 1^st Law, “orbit of a planet with respect to the Sun is an ellipse, with the Sun at one of the two foci.” Orbit of the Moon with respect to Earth is also distinctly elliptical, but this ellipse has a varying eccentricity as the Moon comes closer to and goes farther away from the Earth in a harmonic style along a full cycle of this ellipse. In this paper, our research results are summarized, where it is first mathematically shown that the “distance between points around any two different circles in three dimensional space” is equivalent to the “distance of points around a vector ellipse to another fixed or moving point, as in two dimensional space”. What is done is equivalent to showing that bodies moving on two different circular orbits in space vector wise behave as if moving on an elliptical path with respect to each other, and virtually seeing each other as positioned at an instantaneously stationary point in space on their relative ecliptic plane, whether they are moving with the same angular velocity, or different but fixed angular velocities, or even with different and changing angular velocities with respect to their own centers of revolution. This mathematical revelation has the potential to lead to far reaching discoveries in physics, enabling more insight into forces of nature, with a formulation of a new fundamental model regarding the motions of bodies in the Universe, including the Sun, Planets, and Satellites in the Solar System and elsewhere, as well as at particle and subatomic level. Based on the demonstrated mathematical analysis, as they exhibit almost fixed elliptic orbits relative to one another over time, the assertion is made that the Sun, the Earth, and the Moon must each be revolving in their individual circular orbits of revolution in space. With this expectation, individual orbital parameters of the Sun, the Earth, and the Moon are calculated based on observed Earth to Sun and Earth to Moon distance data, also using analytical methods developed as part of this research to an approximation. This calculation and analysis process have revealed additional results aligned with observation, and this also supports our assertion that the Sun, the Earth, and the Moon must actually be revolving in individual circular orbits.

Production of electricity using hydro-kinetic tidal turbines has many challenges that must to be overcome to ensure reliable, economic and practical solutions. Energy from flowing water is converted by a system comprising: the turbine rotor blades, a gearbox, an electrical generator, control systems, power electronics, export cables, and a connection to the electricity grid. To date these have often been modelled using simulations of independent systems, lacking bi-directional, real-time, coupling. This approach leads to critical effects being missed. Turbulence in the flow, results in large velocity fluctuations around the blades, causing rapid variation in the shaft torque and generator speed, and consequently in the voltage seen by the power electronics and consequently the export power quality. The resulting poor quality power may be unacceptable to the grid. Conversely, grid frequency and voltage changes can also cause the generator speed to change, resulting in changes to the shaft speed and torque and consequently changes to the lift and drag forces acting on the blades. Clearly, fully integrated, bi-directional, models are needed. Here we present two fully coupled models which use different approaches to model the hydrodynamics of rotor blades. The first model uses Blade Element Momentum Theory (BEMT), resulting in an efficient tool for turbine designers. The second model also uses BEMT combines this with an actuator line model of the blades coupled to an unsteady computational fluid dynamics (CFD) simulation. This simulation, implemented in OpenFOAM, uses an energy balance to compute the shaft speed. Both the BEMT and CFD models are coupled to an Open Modellica model of the electro-mechanical system. Both models have been used to simulate the performance of a 1.2m diameter, scale model, of a three bladed horizontal axis tidal turbine tested in the University of Edinburgh FloWave Ocean Energy Research Facility. The turbulent flow around the blades and the mechanical-electrical variables during the stable period of operation are analysed. Time series and tabulated average values of mechanical thrust, power, torque, and rotational speed as well as electrical variables of generator power, electromagnetic torque, voltage and current are presented for the coupled system simulation. The relationship between the mechanical and electrical variables and the results from both tidal turbine approaches are discussed. Our comparison shows that while the BEMT model provides an effective design tool (leading to slightly more conservative designs), the CFD/BEMT simulations provide more accurate predictions of the blade loads which can be especially important in assessing fatigue on the blades (though at an increased computational cost).