The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

Oil floating on the sea surface can be detected by both passive and active methods using the ultraviolet-to-microwave spectrum, whereas oil immersed below the sea surface can signal its presence only in visible light. This paper presents an optical model of a sea area deeply polluted by an oil suspension (10 ppm) located in a layer (thickness 5 m) separated from the sea surface by a clear layer (thickness 1 m). The impact of wavelength and state of the sea surface on reflectance changes is shown based on the results of Monte Carlo ray tracing. A two-wavelength index of reflectance is proposed to detect oil suspended in the water column (645-469 nm).

This paper uses polypropylene (PP) as the matrix and acrylic acid (AA) and maleic anhydride (MAH) as functional monomers to prepare PP-g-(AA-MAH) fibers by suspension grafting and melt-blown spinning technology that are easy to industrially scale-up. The fibers can be used to adsorb aniline from wastewaters. Results showed that the grafting ratio reached the maximum of 12.47%. The corresponding optimal conditions were grafting time of 3h, AA : MAH = 0.75, total monomer content of 55%, benzoyl peroxide 1.4%, xylene concentration of 6 mL/g PP, and deionized water content of 8 mL/g PP. Owing to its good fluidity and thermal stability, the product of suspension grafting can be used for melt-blown spinning. Infrared spectroscopic and nuclear magnetic resonance spectroscopic analyses indicated that AA and MAH were successfully grafted onto PP fibers. After grafting, the hydrophilicity of PP-g-(AA-MAH) fiber increased. Therefore, it had higher adsorptivity for aniline and the adsorption capacity could reach 42.2 mg/g at 45 min. Moreover, the PP-g-(AA-MAH) fibers showed good regeneration performance.

Many species of the Asteraceae family are used in traditional Mexican medicine for possessing healing properties. Ageratina pichinchensis (Asteraceae) is a plant used for the treatment of gastric ulcers, deep wounds and for its antifungal effects. The aim of this study was to establish a cell suspension culture of A. pichinchensis, quantify the anti-inflammatory constituents 2,3-dihydrobenzofuran and 3-epilupeol, to evaluate the anti-inflammatory potential of its extracts and perform a phytochemical analysis. Cell suspension cultures were established in MS culture medium supplemented with 30 g L-1 sucrose and 1.0 g L-1 α-naphthaleneacetic acid (NAA) plus 0.1 mg L-1 6-furfurylaminopurine (KIN). The ethyl acetate extracts of cell suspension cultures analyzed by GC revealed that the maximum production of compounds The anti-inflammatory activity of these extracts exhibited significant inhibition of NO production. Furthermore, the phytochemical study of EtOAc and MeOH extracts of the biomass on day 20 led to the identification of 17 known compounds. The structures of compounds were assigned by analysis of 1D and 2D NMR data and the remainder by GC-MS. This is the first report of the production of the (-)-Artemesinol, (-)-Artemesinol glucoside, Encecalin and 3,5-diprenyl-acetophenone compounds by a cell suspension cultures of A. pichinchensis.

In the context of improving the comfort and dynamics of the vehicle, the suspension system has been continuously developed and improved, especially using magnetorheological (MR) shock absorbers. The development of this technology which is relatively new has not been easy. Thus, the first widespread commercial use of MR fluid in a semi-active suspension system was implemented in passenger cars. The magnetorheological shock absorber can combine the comfort with the dynamic driving, because it allows the damping characteristic to be adapted to the road profile. The main objective of the paper is to analyze the dynamic behavior of the magnetorheological shock absorber in the semi-active suspension. In this sense, the author carried out a set of experimental measurements with a damping test bench, specially built and equipped with modern equipment. The results obtained from the experimental determinations show a significantly improved comfort when using a magnetorheological shock absorber, compared to a classic one, by the fact that the magnetorheological shock absorber allows to modify the damping coefficient according to the road conditions, thus maintaining the permanent contact between the tire and the road due to increased damping force.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

In order to coordinate the damping performance and energy regenerative performance of energy regenerative suspension, this paper proposes a structure of vehicle semi-active energy regenerative suspension with electro-hydraulic actuator (EHA). In light of the proposed concept, a specific energy regenerative scheme is designed and the mechanical properties test is carried out. Based on the test results, the parameter identification for the system model is conducted using recursive least squares algorithm. On the basis of system principle, the nonlinear model of the semi-active energy regenerative suspension with EHA is built. Meanwhile, LQG control strategy of the system is designed. And then the influence of the main parameters of EHA on the damping performance and energy regenerative performance of suspension is analyzed. Finally, the main parameters of EHA actuator are optimized via genetic algorithm. The test results show that when sinusoidal is input at the frequency of 2Hz and the amplitude of 30mm, the spring mass acceleration RMS value of optimized EHA semi-active energy regenerative suspension is reduced by 22.23% and energy regenerative power RMS value is increased by 40.51%, which means while meeting the requirements of certain vehicle ride comfort and driving safety, energy regenerative performance is improved significantly.

The search for graphene or few layer graphene production methods that are simple, allow mass production and yield good quality material continues to provoke intense investigation. The present work contributes through the study of the aqueous exfoliation of four types of graphene sources, namely graphite and graphite nanoflakes with different morphologies and geographical origin. The exfoliation was achieved in an aqueous solution of a soluble pyrene derivative that was synthesized to achieve maximum interaction with the graphene surface at low concentration (5 x 10-5 M). The yield of bilayer and few layer graphene obtained was quantified by Raman spectroscopic analysis and the adsorption of the pyrene derivative on the graphene surface was studied by thermogravimetric analysis and X-ray diffraction. The whole procedure was rationalized with the help of molecular modeling.

The synthesis of additives for thinning mineral suspensions based on sodium polyacrylate was carried out. The effect of molecular weight regulators on the molecular weight characteristics of the polymer and the effect of such polymers on the rheological properties of suspensions was studied. Sodium acrylate polymers are synthesized by free radical polymerization in aqueous solution using molecular weight regulators. The molecular weight characteristics of the polymeric samples were estimated by viscometry using Mark-Houwink-Kuhn-Sakurada (MHKS) equation. Synthesized polymers were used as thinners ceramic slurries, prepared according to the recipe of the enterprises producing ceramic products. The thinning ability of polymer samples with different molecular weights was estimated using an Engler viscometer from the time of the ceramic slurry flow. The influence of the type and amount molecular weight regulator on polyacryates was revealed. It was found that molecular weight synthesized samples was in the range of 21000 - 91000. It was determined that samples with a molecular weight of 28000 - 35000 synthesized using mercaptoethanol (at a dosage of 0.5-1.5% by weight of the monomer) provide optimal fluidity to the ceramic slurry.

The production and N-glycosylation of recombinant human butyrylcholinesterase (BChE), a model highly glycosylated therapeutic protein, in a transgenic rice cell suspension culture treated with kifunensine, a strong α-mannosidase I inhibitor, was studied in a 5 L bioreactor. A media exchange was performed at day 7 of cultivation by removing spent sugar rich media (NB+S) and adding fresh sugar free (NB-S) media to induce the rice α-amylase 3D (RAmy3D) promoter to produce rice recombinant human BChE (rrBChE). Using a 1.25X concentrated sugar-free medium together with an 80% reduced working volume during the media exchange lead to a total active rrBChE production level of 79 ± 2 µg (g FW)^-1 or 7.5 ± 0.4 mg L^-1 in the presence of kifunensine, which is 1.5-times higher than our previous bioreactor runs using normal sugar free medium with no kifunensine treatment. Importantly, the amount of secreted active rrBChE in culture medium was enhanced in the presence of kifunensine, comprising 44% of the total active rrBChE at day 5 post-induction. Coomassie stained SDS-PAGE gel and Western blot analyses reveal different electrophoretic migration of purified rrBChE bands with and without kifunensine treatment, which is attributed to different N-glycoforms. N-Glycosylation analysis shows substantial increase of oligomannose glycans (Man5/6/7/8) in rrBChE treated with kifunensine compared to controls. However, mass transfer limitation of kifunensine is likely the major reason for incomplete inhibition of α-mannosidase I in this bioreactor study.

Background: Physical activity has been considered as a promising approach to slow down the disease process in Multiple Sclerosis (MS) patients. While the functional impairments of MS have been studied in detail, but there is limited evidence of the efficacy of exercise interventions on the Multiple Sclerosis functional composite (MSFC) score in these patients. The study aim was to in-vestigate the improvement in MSFC score by multi-function swing suspension training (MFSST) in the women with MS. Methods: The patients were divided into the intervention and control groups. A total of 47 MS patients completed the MSFC components at baseline and after the intervention. Z scores were created for each test based on control means. Results: The MSFC components showed a significant increment in comparison with the baseline levels in the four, six, and eight weeks following the first exercise session (all p<0.05). These dif-ferences in the control group were not significant. The improvement in the MSFC score and the component Z-scores in the intervention groups was found from the fourth week onwards. Conclusions: The study findings highlight that MFSST can be used as an effective treatment method in MS patients due to its positive effects on physical parameters, such as muscles strength, functional impairments, and cognitive problems.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

The demand for suspensions used in thermal spray processes is expanding from research labs using the lab-prepared suspensions toward actual coating production in different industrial sectors. Industrial applications dictate reduced production time and effort which may in turn justify the development of the market for ready-to-use commercial suspensions. To this end, some of the powder suppliers have already taken steps forward by introducing to the market suspensions of some of the most used materials such as yttria-stabilized zirconia (YSZ), alumina and titania. There is, however, a need to compare the suspension characteristics over time and the resultant coatings when using these suspensions as compared with the freshly prepared home-made suspensions. In this work, such comparison is done using YSZ suspensions of the sub-micron to a few micron powders. In addition, some changes in the suspensions' formula were performed as a tool to vary the coatings’ microstructures in a more predictable way, without variation of spray parameters. The coatings were generated using both radial and axial injection of the suspensions into Oerlikon-Metco 3MB and Mettech Axial III plasma spray torches, respectively. A clear effect of suspension viscosity on the coating microstructure was observed using the 3MB torch with radial injection of suspension (i.e. cross flow atomization). The viscosity role, however, was not dominant when using the Axial III torch with axial feed injection system (i.e. coaxial flow atomization).

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Gymnema sylvestre is a pharmacological plant which has a rich source of bioactive compounds specifically gymnemic acid (GA) and phenolic compounds (PC) that used for pharmaceutical industries. Sources for naturally occurring bioactive compounds are limited, due to geographical and seasonal variations; on the other hand, it is commercially in demand. Biosynthesis of G. sylvestre phytochemicals through in vitro culture often enhanced by elicitation. The use of cell suspension cultures (CSC) has interested serious attention on the production of essential phytochemicals. The current study is aimed at improving the contents of GA and PC in G. sylvestre CSC using the copper oxide nanoparticles (CuO NPs). Callus was obtained on MS medium with 2.0 mg/L 2,4-dichlorophenoxyacetic acid (2,4-D), 0.1 mg/L kinetin (KIN), phytoagar (8.0 g/L), and sucrose (30 g/L). The above medium devoid of agar was used for the initiation of CSC. The CSC was treated with three levels of CuO NPs (1, 3 or 5 mg/L) to enhance the production of GA and PC. The greatest amount of GA (89.25 mg/g dry cell mass, DCM), total phenolic (245.10 mg/g), and flavonoid (4.57 mg/g) in CSC were achieved when G. sylvestre cells were treated for 48 h with 3 mg/L CuO NPs. Also, the biomedical potential (antioxidant, antidiabetic, anti-inflammatory, antibacterial, antifungal and anticancer activities) were also high in the CuO NPs (3 mg/L) treated CSC extracts of G. sylvestre. CuO NPs elicitation of CSC significantly increased production of GA (9-fold), and PC than non-elicited CSC in G. sylvestre.

Background: Upper extremities’ function impairments (UEFI) and gait impairment are frequently reported even in the early stages of Multiple Sclerosis (MS) disease. These motor deficits can negatively affect the quality of life (QOL) in MS patient. Exercise has been repeatedly introduced as a beneficial adjuvant therapy for MS, attenuating a wide range of physical and psychological symptoms without any side effects or increased risks of relapse or exacerbation in disease symptoms.Aim: This paper investigates the effect of multi-function swing suspension training (MFSST) program on upper and lower extremities’ function (ULEF), and QOL in MS women according to expanded disability status scale (EDSS) score.Design: Experimental method with a pre-test and post-test design with control group. Setting: The department of Sports Injuries and Corrective Exercise at the Shahid Bahonar University of Kerman.Population: Forty-seven MS women.Methods: Eligible subjects who matched the selection criteria were randomly assigned into three groups as follow: i. Intervention group A (EDSS of 2 – 4), ii. Intervention group B (EDSS of 4.5 – 6.5), and iii. Control group (EDSS of 2 – 6.5). The intervention groups have been trained by the SET program for a duration of 8 weeks. At baseline and after the intervention, the upper extremities’ function (UEF) and the lower extremities’ function (LEF) were assessed by 9-hole peg test (9HPT) and the timed 25-foot walk (T25FW) test, respectively. Moreover, participants’ QOL was measured using the Short Form questionnaire (SF-36).Results: A significant difference was found between the pre-test and post-test variables of walking speed and upper extremity endurance in intervention groups, and between the intervention groups and control group (P < 0.05). Compared to control group, both intervention groups showed improvements in all subscales of QOL, except emotional role limitation score.Conclusions: In summary, these results show that the present protocol of MFSST could be effective in improving ULEF and QOL in MS patients, showing the improvements after 4^th week. Moreover, this protocol was more useful for patients with an EDSS score of more than 4.5. Therefore, it seems that exercise therapy should be considered as a beneficial clinical intervention approach to improve ULEF and QOL in MS patients.

Cannabidiol (CBD) is a non-intoxicating compound extracted from Cannabis sativa, showing antidepressant-like effects in different rodent models. However, inconsistent results have been described depending on the species and the strain used to assess depressive-like behaviour. Moreover, only a few studies have investigated the effect of CBD in female rodents. Therefore, we aimed to i) investigate the effects of CBD in two different strains of mice (Swiss and C57BL/6) and in a rat model of depression based on selective breeding (Flinders Sensitive and Resistant Lines, FSL and FRL) subjected to tests predictive of antidepressant-like effects; and ii) investigate the influence of sex in the effects of CBD in both mice and rats. CBD induced an antidepressant-like effect in male Swiss but not in female Swiss or C57BL/6 mice in the tail suspension test (TST). In male FSL rats, CBD produced an antidepressant-like effect one-hour post-injection. However, in female FSL, CBD induced a bimodal effect, increasing the immobility time at one hour and decreasing it at two hours. Ketamine produced an antidepressant-like effect in male and female FSL rats at different doses. In conclusion, strain, sex, and administration time affect CBD's behavioural response to rodents exposed to tests predictive of antidepressant effects.

With the automotive industry moving towards automated driving, sensing is increasingly important in enabling technology. The virtual sensors allow data fusion from various vehicle sensors and provide a prediction for measurement that is hard or too expensive to measure in another way or in the case of demand on continuous detection. In this paper, virtual sensing is discussed for the case of vehicle suspension control, where information about the relative velocity of the unsprung mass for each vehicle corner is required. The corresponding goal can be identified as a regression task with multi-input sequence input. The hypothesis is that the state-of-art method of Bidirectional Long-Short Term Memory (BiLSMT) can solve it. In this paper, a virtual sensor has been proposed and developed by training a neural network model. The simulations have been performed using an experimentally validated full vehicle model in IPG Carmaker. Simulations provided the reference data which was used for Neural Network (NN) training. The extensive dataset covering 26 scenarios has been used to obtain training, validation and testing data. The Bayesian Search was used to select the best neural network structure using root mean square error as a metric. The best network is made of 167 BiLSTM, 256 fully connected hidden units and 4 output units. Error histograms and spectral analysis of the predicted signal compared to the reference signal are presented. The results demonstrate the good applicability of neural network-based virtual sensors to estimate vehicle unsprung mass relative velocity.

Foot-and-mouth disease virus (FMDV) causes the highly contagious foot-and-mouth disease, which is characterized by the appearance of vesicles in and around the mouth and feet of cloven-hoofed animals. BHK21 cells are the cell line of choice for the propagation of FMDV for vaccine production world-wide but vary in their susceptibility for different FMDV strains. Previous studies showed that the FMDV resistance of a certain BHK cell line can be overcome by using a closely related but permissive cell line for the pre-adaptation of the virus, but the adapted strains were found to harbor several capsid mutations. In this study, these adaptive mutations were introduced into the original Asia-1 Shamir isolate individually or in combination to create a panel of 17 Asia-1 mutants by reverse genetics and examine the effects of the mutations on receptor usage, viral growth, immunogenicity and stability. A single amino acid exchange from glutamic acid to lysine at position 202 in VP1 turned out to be of major importance for productive infection of the suspension cell line BHK-2P. In consequence, two traditionally passage-derived strains and two recombinant viruses with a minimum set of mutations were tested in vivo. While the passaged-derived viruses showed a reduced particle stability, the genetically modified viruses were more stable but did not confer a protective immune response against the original virus isolate.