With the introduction of the IEC 61850 standard, the path is set for a single communication topology covering all substation levels. The standard has the potential to change the way substations are designed, build, tested and maintained. This means that the key segment of the substation, its protection system, will go through a transition period with the end goal of having a digitalized substation where all information exchange is performed over an Ethernet communication bus. The goal of this paper is to analyse the performance impact of the IEC 61850-9-2LE on the protection system. To do this, a laboratory hardware-in-the-loop test setup is developed representing traditional, hybrid and digital substation topology. This setup served to simulate faults and create transient waveforms in an extended IEEE 123 node test system, which were then used to detect the reaction times of protection relay devices. To verify protection relay results significant number of tests are performed clearly showing benefits which can be gained by distribution system digitalization.

Low-frequency audible noise generated by the magnetostriction effect inherent to the operation of power transformers has become a major drawback, especially in cases where the electrical substation is located in urban areas subject to strict environmental regulations that imposes sound pressure limits, differing for day and night periods. Such regulations apply a +5 dB penalty if a tonal component of noise is present, which is clearly the case of magnetostriction noise, typically concentrated at twice the industrial frequency (50 Hz or 60 Hz, depending on the country). The strategy used to eliminate the tonal characteristics, therefore contributing to establish compliance with the applicable regulation and to alleviate the discomfort it causes to the human ear, consisted in superimposing to the substation noise a masking sound synthesized from “sounds of nature” with suitable intensities, to flatten the noise spectrum while enhancing the soundscape. The masking system (heavy-duty speakers powered by a microprocessor platform) was validated at an already judicialized urban scenario. Measurement results confirmed that the masking solution was capable of flattening the tonal frequencies, whose beneficial effect yielded the cancellation of the public civil action filed by the neighbors. The proposed solution is ready to be replicated to other scenarios.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

The upgrade of energy infrastructure to those of smart grids, necessarily goes through the provision of integrated technological solutions that ensure the interoperability of their business capabilities and reduce the risk of devaluation of the systems used. The heterogeneity of the infrastructures and the dynamics of their operating environment, requires the continuous reduction of the complexity, the faster execution of the processes and the easy addition of innovative counterparts. Also, the integrated management of the overall ecosystem demands the provision of end-to-end interconnection, quality assurance, the definition of strict security policies, collaborative integration and correlation of events. In this respect, every design detail can be critical to the success or failure of a costly and ambitious project, such as that of smart energy networks. This work presents communication operating standards specific to the smart electricity networks applications, which should be taken into account in the process of planning and implementation of new infrastructures.

In various domains such as energy, manufacturing, and maritime, cyber-physical systems (CPS) have seen increased interest. Both academia and industry have focused on the cybersecurity aspects of such systems. The assessment of cyber risks in CPS is a popular research area with many existing approaches that aim to suggest relevant methods and practices. However, few works have addressed the extensive and objective evaluation of the proposed approaches. In this paper, a standard-aligned evaluation methodology is presented and empirically conducted to evaluate a newly proposed cyber risk assessment approach for CPS. The approach, which is called FMECA-ATT&CK is based on Failure Mode, Effects & Criticality Analysis (FMECA) risk assessment process and enriched with the semantics and encoded knowledge in the Adversarial Tactics, Techniques, and Common Knowledge framework (ATT&CK). Several experts were involved in conducting two risk assessment processes, FMECA-ATT\&CK and Bow-Tie, against two use cases in different application domains, particularly an autonomous passenger ship (APS) as a maritime use case and a digital substation as an energy use case. This allows for the evaluation of the approach based on a group of characteristics, namely, applicability, feasibility, accuracy, comprehensiveness, adaptability, scalability, and usability. The results highlight the positive utility of FMECA-ATT&CK in model-based, design-level, and component-level cyber risk assessment of CPS with several identified directions for improvements. Moreover, the standard-aligned evaluation method and the evaluation characteristics have been demonstrated as enablers for the thorough evaluation of cyber risk assessment methods.

Accurate and stable cost forecasting of substation projects is of great significance to ensure the economic construction and sustainable operation of power engineering projects. In this paper, a forecasting model based on the improved least squares support vector machine (ILSSVM) optimized by wolf pack algorithm(WPA) is proposed to improve the accuracy and stability of the cost forecasting of substation projects. Firstly, the optimal features are selected through the data inconsistency rate (DIR), which helps reduce redundant input vectors. Secondly, the wolf pack algorithm is used to optimize the parameters of the improved least square support vector machine. Lastly, the cost forecasting method of WPA-DIR-ILSSVM is established. In this paper, 88 substation projects in different regions from 2015 to 2017 are chosen to conduct the training tests to verify the validity of the model. The results indicate that the new hybrid WPA-DIR-ILSSVM model presents better accuracy, robustness and generality in cost forecasting of substation projects.

Because imbalanced power will cause the loss of the propulsion motor of the railway vehicle, and the increase in temperature will shorten the service life of the electric vehicle. Not only this, but also increase the cost of electricity and maintenance. In the past, the industry only focused on methods to improve power quality such as load capacity, relay setting, and harmonic resolution. Now, the consider of three-phase unbalance rate (TPUR) must be applied. I propose special transformers wiring (STW) to improve the three unbalance rates and provide different transformer wiring methods. According to the IEEE Committee, in the future, power companies will need to install balanced relay stations to improve three-phase unbalance rate. the internal regulations of Taipower must be less than 4.5% (voltage unbalance rate (NPSUR)of 2.5% and motor temperature rise of 12.5%). the derivation of the transformer "three-phase unbalance rate" model is the focus of the railway system. This research is based on the model derivation of different wiring methods to improve the hot problem caused by the three-phase imbalance and improve the service life of the train. And pointed out that Scott, Le-Blanc, Modified-Woodbridge three wiring methods can be applied to future railway system routes to improve the three-phase unbalance rate, in line with the IEEE standard of less than 2%.