Monitoring of structures is one of the engineering challenges of the 21st century. At the same time, as a result of changes in the conditions of use, design errors, many building structures require strengthening. The article presents research on the development of the external strengthening carbon fiber textile with an option of self-sensing. The idea is based on the pattern of resistive strain gauge, where thread is provided in a zig-zag of parallel lines. Already the first laboratory tests showed the high efficiency of the system in the measurement of strains, but also revealed the sensitivity of measurement to environmental conditions. The article presents studies on the influence of temperature and humidity on the measurement. To separate those effects, resistance changes were tested on unloaded concrete and wooden samples. The models were placed in a climatic chamber and the daily cycle of temperature and humidity changes was simulated. The results of the research confirm preliminary observations. Resistivity growths with the temperature. This effect is more visible on concrete samples, presumably due to its greater natural humidity. The strain measurement with carbon fibers is very sensitive to temperature changes and application of this method in practice requires compensation.

Deformation monitoring is beneficial to ensure the service safety of long tunnel. An three-direction (vertical, transverse and axial) deformation estimation method using long-gauge fiber Bragg grating (FBG) sensing technology is proposed and applied to a long tunnel by integrating mechanical analysis and field monitoring during the service state. The key issues of the proposed method for identifying the three-direction deformation are discussed, such as establishing the separation model of coupling strain on cross section, deriving the theory of deformation identification in three directions, and determining the sensor layout of the long tunnel. A major advantage of the proposed method is that the three-direction deformation of the tunnel can be monitored in real time using distributed long-gauge strain sensors. The numerical analysis and field test results verify the feasibility of the proposed method.

Isometric exercises for physiotherapeutic rehabilitation are often prescribed, with little quantification of the load being prescribed. This article aimed to provide a framework and practical examples of how the physiotherapist may take a more quantitative evidence-based approach to isometric assessment, monitoring, and exercise prescription of knee osteoarthritis, by integrating a strain gauge into their practice. Strength measures to monitor were discussed. A series of fourteen studies were reviewed, with the intent of identifying isometric exercises that had been utilized in the rehabilitation of knee osteoarthritis. Of the fourteen studies, the three most identified isometric exercises were seated knee extension, knee flexion, and the supine straight leg raise. The integration of strain gauge technology with these exercises provided the focus of the remainder of the article.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

We have successfully measured amyloid beta (Aβ) (1-40) protein added in human serum by a NiCr strain gauge cantilever biosensor immobilized with liposomes incorporating cholesterol. Importantly, we investigated the effect of incorporation of cholesterol in the liposome in order to suppress the interaction between the liposome and many different proteins included in human serum. It was revealed that incorporating cholesterol suppresses the interaction between the proteins other than Aβ in human serum and the liposome. Finally, we detected Aβ(1-40) in human serum with typical chronological behaviors due to Aβ aggregation and fibrillization. Furthermore, as a digital low-pass filtering procedure could reduce external noises, the cantilever sensor immobilized with liposome incorporating cholesterol can detect low-concentrated Aβ in human serum.

The inter-tip times (ITTs) of tipping-bucket rain gauges potentially provide the highest-resolution intensity data that can be acquired from this type of gauge. At an intensity of 100 mm h-1, a typical gauge with a sensitivity of 0.2 mm of rainfall would be expected to tip every 7.2 seconds. However, TBRGs are often equipped with syphons, to reduce the dynamic calibration error that results from continued (and unmeasured) inflow to a bucket as it tips. This increases the accuracy of rainfall depth recording, but the time to fill and empty the syphon can reduce the ability of a TBRG to respond to (and for the ITTs to reflect) short-term intensity fluctuations. This ability is already limited by the discretisation arising from the filling and emptying of the buckets themselves. Laboratory tests with controlled water inflow rates were performed using two high-quality TBRGs, one a 'straight-through' design and the other syphon-equipped. These confirmed that at all intensities at which the syphon operates, a regular sequence of fixed-duration ITTs (such as the 7.2 s mentioned above) does not occur. Rather, the ITTs are perturbed by the syphon cycling. The gauges were also co-located in the field, and linked to carefully synchronised event data loggers. Data collected during several rainfall events revealed differences in the ITTs, and again confirm that the ITT sequence of a syphon-equipped TBRG exhibits artefacts related to syphon operation, that are not present in the 'straight-through' data. These artefacts can result in ITT differences of many minutes, depending on the rainfall intensity, and are problematic for the use of ITTs to estimate intensity. Peaks and troughs in the intensity profile also differed between the two gauges. It is recommended that in the application of TBRGs for studies where short-term intensity data are required, 'straight-through' gauges should be used, and syphon-equipped gauges avoided.

We review the main features of the non-local gauge, named the contour gauge. The contour gauge belongs to the axial type of gauges and extends the local gauge used in the most of approaches. The geometry of gluon fields and the path-dependent formalism are the essential tools for the description of non-local gauges. The principle feature of the contour gauge is that there are no the residual gauges which are left in the finite domain of space. In the review, we present the useful correspondence between the contour gauge conception and the Hamiltonian (Lagrangian) formalism. The Hamiltonian formalism is turned out to be a very convenient framework for the understanding of contour gauges. The comprehensive comparison analysis of the local and non-local gauges advocates the advantage of the contour gauge use. As an example of practical worth, we consider the Drell-Yan process and discuss the gauge invariance of the corresponding hadron tensor. We show that the appropriate use the contour gauge leads to the existence of extra diagram contributions. These additional contributions, first, restore the gauge invariance of the hadron tensor and, second, give the important terms for the observable quantities. We also demonstrate the significant role of the additional diagrams to form the relevant contour in the Wilson path-ordered exponential. Ultimately, it leads to the spurious singularity fixing. Moreover, in the present review, we discuss in detail the problem of spin and orbital angular momentum separation. We show that in SU(3) gauge theories the gluon decomposition on the physical and pure gauge components has a strong mathematical evidence provided the contour gauge conception has been used. In addition, we prove that the contour gauge possesses the special kind of residual gauge that manifests at the boundary of space. Besides, the boundary field configurations can be associated with the pure gauge fields.

When discussing the gauge symmetries of any theory, the Henneaux-Teitelboim transformations are often underappreciated or even completely ignored, due to their on-shell triviality. Nevertheless, these gauge transformations play an important role in understanding the structure of the full gauge symmetry group of any theory, especially regarding the subgroup of diffeomorphisms. We give a review of the Henneaux-Teitelboim transformations and the resulting gauge group in the general case, and then discuss its role in the applications to the class of topological theories called nBF models, relevant for the constructions of higher gauge theories and quantum gravity.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

1) Background: Ultrasound-based strain imaging is now available in several ultrasound (US) scanners. Strain ratio (SR) can be used to quantify strain recorded simultaneously in two different user-selected areas, ideally exposed to the same amount of stress. The aim of this study was to evaluate SR variability when assessed in an in-vitro setup with a tissue-mimicking phantom, on resected tissue samples and in live tissue scanning with endoscopic applications. 2) Material and methods: Retrospective analysis of SR for quantification of elastic contrasts in a tissue-mimicking phantom containing four homogenous inclusions, in 38 resected bowel wall lesions and in 48 focal pancreatic lesions examined in vivo. Median SR and the inter-quartile range (IQR) was calculated on all external and endoscopic US-applications. The IQR/median provides a measure of the SR variability focusing on the two percentiles of the data closest to the median value. 3) Results: The overall variability of SR was lowest in a tissue-mimicking phantom (mean QR/median SR: 0.07). In resected bowel wall lesions representing adenomas, adenocarcinomas or Crohn lesions, the variability increased (mean IQR/Median: 0.62). During an endoscopic examination of focal pancreatic lesions in vivo, the variability increased further (mean IQR/Median: 2.04). 4) Conclusion: SR variability increased when assessed on different targets with growing heterogeneity and biological variability as one moved from homogeneous media to live tissues and endoscopic application. This may indicate a limitation for the accuracy SR evaluation in clinical applications.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

In this note, the toy-model of Fourth Generation quarks coupling to Standard Model particles through unknown Lagrangian has been figured. Eventually producing a 103 TeV vector gauge boson, which is a special gauge boson that appears in unification models and here as a mediator for WeakSM4 interaction. Another anomaly of different gauge boson has been reported.

This note will be a brief account of an unknown vectorial mathematical current in SM4 Field based on disintegrating the Lagrangian of quarks in SM4 into four parts. It is shown that the current breaks while interacting with the quarks and makes the quarks to not interact with fourth-generation quarks. This note also shows that gauge bosons are produced while these currents symmetry break and provides the service as mediators.

Precipitation during 2001-2016 over the northern and central part of Tuscany was studied in order to characterize the rainfall regime. The dataset consisted of hourly cumulative rainfall series recorded by a network of 801 rain gauges. The territory was divided into 30x30 km square areas, the annual, seasonal and daily Average Cumulative Rainfall (ACR) in all areas was estimated along with its uncertainty. The trend analysis of ACR time series was performed by means of the Mann-Kendall test. Four climatic zones were identified: the north-western was the rainiest, followed by the north-eastern, north-central and south-central. An overall increase in precipitation was identified, more intense in the north-west, and determined mostly by the increase in winter precipitation. On the entire territory, the ACR, number of rainy days, mean precipitation intensity and sum of daily ACR in four intensity groups were evaluated at annual and seasonal scale. The main result was a magnitude of the ACR trend evaluated as 35 mm/year, due mainly to an increase in light and extreme precipitations. This result is in contrast with the decreasing rainfall detected in the past decades.

The paper presents an extensometer designed to measure two mechanical strains at the same time—one from tensile load and the other from torsion load. Strain transducers provide different electric signals, which, after calibration, lead to the simultaneous measurement of linear (ε) and angular (γ) strains. Each of these two signals depends on the measured process and is not influenced by the other strain process. This extensometer is designed to be easily mounted on the sample with only two mounting points and can be used to measure the combined cyclical fatigue of tensile and torsional loadings. This extensometer has two bars—one rigid, reported at the resulting stress points, and one elastic and deformable. The elastic deformable bar has two beams with different orientations. When the sample is deformed, both beams are loaded by two bending moments (perpendicular to each other and both perpendicular on the longitudinal axis of the bars).

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

Many (if not a very large number) of metals and alloys evince substantial softening with torsion deformation to strains not usually achievable in tension. Of course, softening has long been observed by discontinuous dynamic recrystallization (DDRX) but this paper will discuss cases where softening is associated by texture development with large-strain deformation that is not reliant on changes in the dislocation hardening. This paper reviews the work of the current authors on FCC metals and alloys in this area and extends to a new discussion of BCC and HCP cases.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double <100> and <111> fiber and a unique component of (001)<110>, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

We calculate the spectral function of a boson ladder in an artificial magnetic field by means of analytic approaches based on bosonization and Bogoliubov theory. We discuss the evolution of the spectral function at increasing effective magnetic flux, from the Meissner to the Vortex phase, focussing on the effects of incommensurations in momentum space. At low flux, in the Meissner phase, the spectral function displays both a gapless branch and a gapped one, while at higher flux, in the Vortex phase, the spectral function displays two gapless branches and the spectral weight is shifted at a wavevector associated to the underlying vortex spatial structure which can indicate a 8 supersolid-like behavior. While the Bogoliubov theory, valid at weak interactions, predicts sharp delta-like features in the spectral function, at stronger interactions we find power-law broadening of 10 the spectral functions due to quantum fluctuations as well as additional spectral weight at higher 11 momenta due to backscattering and incommensuration effects. These features could be accessed in 12 ultracold atom experiments using radio-frequency spectroscopy techniques.

A careful examination of the fundamentals of electromagnetic theory shows that due to the underlying mathematical assumptions required for Stokes' Theorem, global charge conservation cannot be guaranteed in topologically non-trivial spacetimes. However, in order to break the charge conservation mechanism we must also allow the electromagnetic excitation fields D, H to possess a gauge freedom, just as the electromagnetic scalar and vector potentials $\varphi$ and A do. This has implications for the treatment of electromagnetism in spacetimes where black holes both form and then evaporate, as well as extending the possibilities for treating vacuum polarisation. Using this gauge freedom of D, H we also propose an alternative to the accepted notion that a charge passing through a wormhole necessarily leads to an additional (effective) charge on the wormhole's mouth.

Stueckelberg-Horwitz-Piron (SHP) electrodynamics formalizes the distinction between coordinate time (measured by laboratory clocks) and chronology (temporal ordering) by defining 4D spacetime events x^μ as functions of an external evolution parameter τ. Classical spacetime events x^μ (τ) evolve as τ grows monotonically, tracing out particle worldlines dynamically and inducing the five U(1) gauge potentials through which events interact. Since Lorentz invariance imposes time reversal symmetry on x⁰ but not τ, the formalism resolves grandfather paradoxes and related problems of irreversibility. The action involves standard first order field derivatives but includes a higher order τ derivative that while preserving gauge and Lorentz invariance removes certain singularities and makes the related QFT super-renormalizable. The resulting field equations are Maxwell-like but τ-dependent and sourced by a current that represents a statistical ensemble of instantaneous events distributed along the worldline. The width λ of this distribution defines a correlation time for the interactions and a mass spectrum for the photons that carry the interaction. As λ becomes very large, the photon mass goes to zero and the field equations become τ-independent Maxwell’s equations. Maxwell theory thus emerges as an equilibrium limit of SHP, in which λ is larger than any other relevant time scale. Particles and fields are not constrained to mass shells in SHP theory, and by exchanging mass may produce pair creation/annihilation processes at the classical level. On-shell evolution with fixed particle masses is restored through a self-interaction associated with the 5D wave equation.

We describe here the coherent formulation of electromagnetism in the nonrelativistic quantummechanical many-body theory. We use the mathematical frame of the field theory and its quantization in the spirit of the QED. This is necessary because of the manifold of misinterpretations emerging from the hystorical development of quantum mechanics, starting from the Schrödinger equation of a single particle in the presence of given electromagnetic fields, followed by the many-body theories of many charged identical particles having just Coulomb interactions inspired from the classical electromagnetic theory of point-like charges. However, this later is known to be inconsistent due to the self-interaction. This way could not be continued further to include properly the magnetic forces between the charged particles and lead to a lot of confusion about the interpretation of the magnetic field in the Hamiltonian, as well as about the gauge invariance. We emphasize the importance of the distinction between the applied (external fields) and the field in the matter. All these problems are length properly solved within the non-relativistic QED, nevertheless the confusion dominates in all the problems related to the magnetic properties of the solid state.

Tomato leaf curl disease (TLCD) is the most common viral disease in the tomato plant. It is caused by begomoviruses, which are viruses that cause plant development to be slowed. Many of the traditional disease management methods are still in use. They are, however, ineffective and out of date. Modern biotechnology is being used to detect illness in tomato plants as early as possible, thus reducing damage to the plants. Through genetic engineering, the spread of viruses may be controlled or prevented entirely. Here reviewed many methods for decreasing or eliminating the viral influence on crop growth through biotechnology and genomics. We also investigated the possibility of genetic engineering to reduce or remove the virus TLCD impact on tomato crop development.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Clew Bay is an important aquaculture production area in Ireland. In this study, we focused on a high-resolution simulation of the Clew Bay region based on a Regional Ocean Modelling System (ROMS). Freshwater discharges from eight rivers are included in the model and a wetting-drying scheme has been implemented. The Clew Bay model simulation was validated and calibrated with available observations (e.g., Acoustic Doppler Current Profilers (ADCP), vertical salinity and temperature profiles and tide gauge) in the geographic area of the model domain. High correlations were found between the model outputs and observed temperature, salinity and tide gauge water levels along with small Root Mean Square Errors. This indicates that the model was able to reproduce the oceanographic phenomena in the study area. The Taylor diagram analysis showed a high correlation coefficient (R=0.99) between the ADCP bottom temperature in the Inner Bay and the Clew Bay model, along with a small Centered Root Mean Square Error (RMSD =0.5 ◦ C). High correlation coefficients (R > 0.80) were found between the model and the two ADCPs for the zonal current component. There was a resemblance in structure between the model and the observed salinity profiles, indicating that freshwater was correctly implemented in the model. Moreover, the correlation coefficient between the model and the tidal sea surface height (SSH) was 0.99, with an RMSD of 0.09 m. We discovered that wind direction and speed have a significant impact on the bay's water inflow rate. The model outputs can be used to provide scientists, fishermen and decision-makers with hydrodynamic information on ocean conditions in the bay.

I want to find an extension of the Hausdorff Measure and Fractal Measure which allows me to compute a unique, satisfying average for functions defined on non-fractal, measurable sets in the sense of Carathedory which has no gauge function.

MgB2 is a hexagonal superconducting material, and its simple composition has led to the development of low-cost practical wires. However, the problem is that the strain characteristics of filaments are inferior to those of other practical wires, but there have been no strain measurements using diffraction method. The reason for this is presumably that it is a little too thick for synchrotron radiation measurements, and the large absorption cross section of the included boron-10 makes it difficult to obtain elastic scattering for neutron measurements. We prepared a wire substituted with boron-11, an isotope with small neutron absorption cross section, and attempted to measure its strain under tensile loading using pulsed neutron.

We have developed a self-consistent model for predicting velocity of 1/2[111] screw dislocation in binary iron--carbon alloys gliding by a high-temperature Peierls mechanism. The methodology of modelling includes: (i) Kinetic Monte-Carlo (kMC) simulation of carbon segregation in dislocation core and determination the total carbon occupancy of the core binding sites; (ii) Determination of kink-pair formation enthalpy of a screw dislocation in iron---carbon alloy; (iii) KMC simulation of carbon drag and determination of maximal dislocation velocity at which the atmosphere of carbon atoms can follow a moving screw dislocation; (iv) Self consistent calculation of average velocity of screw dislocation in binary iron--carbon alloys gliding by a high-temperature kink-pair mechanism under constant strain rate. We conduct a quantitative analysis of the conditions of stress and temperature at which screw dislocation glide in iron--carbon alloy is accomplished by a high-temperature kink-pair mechanism. We estimate the dislocation's velocity at which screw dislocation brakes away from the carbon cloud and thermally-activated smooth dislocation propagation is interrupted by sporadic bursts controlled by athermal dislocation activity.

The gauge field equation for fluid mechanics established in Part 1 is developed into a first-order scattering theory in the simplified case of a two-dimensional incompressible flow over a flat plate. This is used to present a model for the origin of Tollmien-Schlichting (TS) waves based on scattering between fluid particles. As a result, analytical formulae for the maximum amplification factor and the transition point from laminar to turbulent flow in the boundary layer are obtained. The mathematical transformations from the stationary field equations in Part 1 to a scattering theory with time evolution along the flow axis using Wick rotation are elaborated in detail.

The stage of a super-early scale-invariant Universe is considered on the basis of the Poincaré–Weyl gauge theory of gravity in a Cartan–Weyl space-time. An approximate solution has been found that demonstrates an inflationary behavior of the scale factor and, at the same time, a sharp exponential decrease in the effective cosmological constant from a huge value at the beginning of the Big Bang to an extremely small (but not zero) value in the modern era, which solves the well-known “cosmological constant problem”.

Accurate and consistent rainfall observations are vital for climatological studies in support of better planning and decision making. However, estimation of accurate spatial rainfall is limited by sparse rain gauge distributions. Satellite rainfall products can thus potentially play a role in spatial rainfall estimation but their skill and uncertainties need to be under-stood across spatial-time scales. This study aimed at assessing the temporal and spatial performance of seven satellite products (TARCAT (Tropical Applications of Meteorology using SATellite and ground-based observations (TAMSAT) African Rainfall Climatology And Time series), Climate Hazards Group InfraRed Precipitation with Station data (CHIRPS), Tropical Rainfall Measuring Mission (TRMM-3B43), Climate Prediction Center (CPC) Morphing (CMORPH), the Precipitation Estimation from Remotely Sensed Information using Artificial Neural Networks- Climate Data Record (PERSIANN-CDR), CPC Merged Analysis of Precipitation (CMAP) and Global Precipitation Climatology Project (GPCP) using gridded (0.05o) rainfall data over East Africa for 15 years(1998-2012). The products’ error distributions were qualitatively compared with large scale horizontal winds (850 mb) and elevation patterns with respect to corresponding rain gauge data for each month during the ‘long’ (March-May) and ‘short’ (October-December) rainfall seasons. For validation only rainfall means extracted from 284 rain gauge stations were used, from which qualitative analysis using continuous statistics of Root Mean Squared Difference, Standard deviations, Correlations, coefficient of determinations (from scatter plots) were used to evaluate the products’ performance. Results revealed rainfall variability dependence on wind flows and modulated by topographic influences. The products’ errors showed seasonality and dependent on rainfall intensity and topography. Single sensor and coarse resolution products showed lowest performance on high ground areas. All the products showed low skills in retrieving rainfall during ‘short’ rainfall season when orographic processes were dominant. CHIRPS, CMORPH and TRMM performed well, with TRMM showing the best performance in both seasons. There is need to reduce products’ errors before applications.

Bridges enable communications and transportation of goods nationally and internationally, underpinning economic and social activities, thus they are pylons of our prosperity and mobility. Bridges worldwide are constantly subjected to physical wear, ageing, deterioration, hazards, environmental influences, and increased loading. Loss of performance and functionality of bridge structures would have a crucial impact on overall infrastructural resilience and would cause significant negative economic and social consequences. Monitoring their behaviour for different loading conditions relies on accurate estimations of the stress-strain state of various critical components and remaining capacities. These activities are of high importance for better planning lifespan prolongation, that is the extension of their service life and prevention of unforeseen collapses, in line with sustainability principles of well-informed maintenance. In many cases, access to the structure is limited or even impossible, which causes the need for the deployment of remote and contactless methods. One such innovative technique, which has recently attracted attention in scientific and practical applications is the digital image correlation (DIC). DIC is a contactless approach applicable for long-term measurements, which enables obtaining the full field of strains and deformations. Although the DIC approach has been widely used in world engineering practice for monitoring bridges and has proved to be a reliable and accurate method, there is a lack of systematic integral review on previous practical applications, revealing limitations and perspectives. This is the main motivation and novelty of this study, which will describe selected case studies, in which DIC was used on real full-scale bridge structures and propose improvements for the method.

Background: Evaluation of left ventricular(LV) functions in patients with idiopathic premature ventricular contraction(PVC) with preserved LV Ejection Fraction(LVEF), especially in the subclinical stage, may be of great importance in terms of directing early treatment. Methods: A total of 122 patients, retrospectively recruited, were divided into three groups according to PVC burden: Group 1; 5%PVC<10%, Group 2; 10%PVC<15%, and Group 3; 15% PVC. Transthoracic echocardiography(TTE) was performed to evaluate LV parameters. Results: LV-GLS was found to be significantly lower in groups 2 and 3 with high PVC burden (18.89 ± 1.4, 17.55 ± 2.1, 16.26 ± 1.3; p<0.001 respectively). Correlation analysis revealed a positive and significant correlation between PVC burden with deterioration in LV-GLS (r:0.536; p<0.001). In addition, PVC burden was found to be an independent predictor of LV-GLS deterioration in multiple linear regression analysis(:0.525, p<0.001). The ROC curve analysis demonstrated that a PVC burden cut-off value of 8.4% was associated with a LV-GLS deterioration greater than -18, with a specificity of 75.4% and a sensitivity of 75.4% (AUC: 0.81 [0.73-0.88] 95% CI; p<0.001). Conclusions: PVC burden was an independent predictor of deterioration in LV-GLS. In the presence of subclinical LV injury associated with PVC burden, early catheter ablation strategies may be therapeutically beneficial.

Background and Objectives: Similar to diabetes, the presence of left ventricular (LV) diastolic function (DD) has been reported in various studies which were conducted with people with a diagnosis of impaired fasting blood glucose (FBG). The study aimed to examine the effects of fasting blood glucose (FBG) levels on left atrial strain (LAS) estimated by two-dimensional echocardiography speckle tracking analyses in patients without known diabetes. Material and Methods: The study included 148 participants (74 female and 74 male) without a history of diabetes mellitus or chronic disease. The patients were divided into two groups as follows: individuals with FBG <100 mg/dl and those with FBG between 100-125 mg/dl after at least 8 hours of overnight fasting and according to these FBG levels STE measures were compared. Results: There was a significant decrease in the LA reservoir (52.3±15 vs. 44.5±10.7; p=0.001) and conduit strain (36.9±11.7 vs. 28.4±9.7; p=0.001) in the impaired FBG group. When the STE findings of both ventricles were compared, no significant difference was observed between the groups in right and LV strain imaging. Conclusion: In the earliest stage of LVDD, changes in atrial functional parameters become particularly evident. Echocardiographic analyses of these parameters can help to diagnose and determine the degree of LVDD while the morphological parameters are still normal. The addition of LAS imaging to the routine TTE study in patients with impaired FBG but without a DM diagnosis may be helpful in demonstrating subclinical LVDD or identifying patients at risk for LVDD in this patient group.

This work describes a resonance Raman study performed in domes of monolayer MoS2 using 23 different laser excitation energies covering the visible and near-infrared (NIR) ranges. The multiple-excitation results allowed us to investigate the exciton-phonon interactions of different phonons (A1’, E’ and LA) with different electronic and excitonic optical transitions in biaxially strained monolayer MoS2. The analysis of the intensities of the two first-order peaks, A1’ and E’, and the double-resonance 2LA Raman band as a function of the laser excitation furnished the values of the energies of the indirect gap and the excitonic transitions in the strained MoS2 domes. It was noticed that the out-of-plane A1’ phonon mode is significantly enhanced only by the indirect gap I and the C exciton, whereas the in-plane E’ mode is only enhanced by the C exciton of MoS2 dome, revealing thus a weak interaction of these phonons with the A and B excitons in the strained MoS2 domes. On the other hand, the 2LA Raman band is significantly enhanced at the indirect gap I transition and by the A (or B) exciton, but not enhanced by the C exciton, showing thus that the LA edge-phonons that participate in the double resonance process in MoS2 have a weak interaction with the C exciton.

Magnesium (Mg) alloy is a widely used lightweight metal structural material due to its high specific strength and stiffness, excellent damping performance, and recyclability. Wrought Mg alloys are widely favored in fields such as aerospace, transportation, and biomedical stents. However, most wrought Mg alloys with a hexagonal close-packed (HCP) crystal structure lack sufficient independent slip systems to meet the von Mises criterion for uniform plastic deformation at room temperature. This can result in the formation of strong basal texture during plastic deformation and poor room temperature plastic forming ability. Improving the room temperature forming performance is a crucial challenge that must be addressed to broaden the application of Mg alloy sheets. Our research group has comprehensively summarized significant work and latest research progress in improving the room temperature forming of Mg alloy sheets via extrusion technology in recent years. Specifically, we have developed a new type of asymmetric extrusion technology that combines material structure evolution, mechanical property, and forming behavior analysis. We have elucidated the extrusion process characteristics, texture control mechanism, and forming properties of Mg alloy sheets through plastic deformation mechanisms, mold design, and finite element numerical simulation. Our findings provide a novel extrusion technology for the fabrication of highly formable Mg alloy sheets, which can be utilized in various applications.

This chapter aims to construct a relatively complete, universal, and highly reliable road surface state monitoring and perception system through the research of the A1 contact road reconstruction project of an international airport (hereinafter referred to as the “airport”). The system design is based on on-the-spot investigation, theoretical analysis, and engineering practice, using vibrating string type and resistive strain sensors as sensing means, real-time high-frequency signal acquisition technology as the guide, 4G router for wireless communication technology as the media, and storage technology for monitoring system based on server storage terminals. In combination with engineering background, aircraft motion state, main landing gear configuration, sensor selection and evaluation, and other major factors, the actual monitoring information needs of the plane are fully taken into account, as well as the difference in sensor information types, and the system design is carried out by stratification and classification.

Copper toxicity has been a selective pressure on the sea-ice bacteria due to its widespread occur-rence in Antarctica. Here, with a combined biochemical and metabolomic approach, the Cu2+ ad-aptation mechanisms of Antarctic bacteria were analyzed. Heavy metal resistance pattern of Pb2+ > Cu2+ > Cd2+ > Hg2+ > Zn2+ was observed. Copper treatment did increase the activity of antioxidants and enzymes, maintaining cellular redox state balance and normal cell division and growth. Metabolomics analysis demonstrated that fatty acids, amino acids, and carbohydrates played dominant roles in copper stress adaptation. The results indicated that the adaptation mechanisms of strain O5 to copper stress included protein synthesis and repair, accumulation of organic per-meable substances, up-regulation of energy metabolism, and formation of fatty acids. This study increases the resistance mechanism understanding of Antarctic strains to heavy metals in extreme environments.

Quantitative dynamic strain measurements of the ground would be useful for engineering scale problems such as monitoring for natural hazards, soil-structure interaction studies and non-invasive site investigation using full waveform inversion (FWI). Distributed Acoustic Sensing (DAS), a promising technology for these purposes, needs to be better understood in terms of its directional sensitivity, spatial position, and amplitude for application to engineering-scale problems. This study investigates whether the physical measurements made using DAS are consistent with the theoretical reception patterns and experimental measurements of ground strain made by geophones. Results show that DAS and geophone measurements are consistent in both phase and amplitude for broadband (10s of Hz), high amplitude (10s of microstrain) and complex wavefields originating from different positions around the array when: (1) the DAS channels and geophone locations are properly aligned, (2) the DAS cable provides good deformation coupling to the internal optical fiber, (3) the cable is coupled to the ground through direct burial and compaction, and (4) laser phase noise is mitigated in the DAS measurements. The theoretical relationship between DAS-measured and point-wise strain for vertical and horizontal active sources is introduced using 3D elastic finite-difference simulations. The implications of using DAS strain measurements are discussed including directionality and magnitude differences between the actual and DAS-measured strain fields. A method for spatially aligning the DAS channels with the geophone locations at tolerances less than the spatial resolution of the DAS system is proposed.

The effects of an external strain tensor on the electrical resistivity of a manganite granular system are investigated using a simple approach describing the induced deformation in terms of the tilt angle between adjacent grains. The results obtained assuming the resistivity of each grain as given by a metallic part, coming from the inner grain, and a surface related tunnel contribution, allow to estimate appreciable resistivity variations even in the case of small deformation angles.

The study presents the effect of annealing process parameters on the microstructure, hardness and strain hardening coefficients i.e., the strength coefficient c and the strain hardening exponent n, of 42CrMo4 steel. Seven selected annealing time-temperature schemes are examined for superior steel formability in cold metal forming conditions. The c and n coefficients are first determined in experimental upsetting of annealed samples and then used in FEM simulations of the upsetting process. The results demonstrate that the strain hardening coefficients (c and n) depend on the employed annealing scheme. Compared to the as-received sample, the annealing process reduces the true stress and effectively decrease the hardness of 42CrMo4 steel, improves microstructural spheroidization and, consequently, facilitates deformability of this material. The annealing schemes relying on heating the material to 750 °C and its subsequent slow cooling lead to the highest decrease in hardness ranging from 162 to 168HV. Results obtained with the SEM-EDS, LOM and XRD methods lead to the conclusion that the employed heat treatment schemes cause the initial ferritic-pearlitic microstructure to develop granular and semi-lamellar precipitation of cementite enriched with Mo and Cr in the ferrite matrix. In addition, the annealing process affects the growth of α-Fe grains. The highest cold hardening rate, and thus formability, is obtained for the annealing scheme producing the lowest hardness. The results of FEM simulations are positively validated by experimental results. Obtained results are crucial for further numerical simulations and experimental research connected with developing new cold metal forming methods for producing parts made of 42CrMo4 steel.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

Tipping bucket rain gauges (TBRs) have been, and apparently will continue to be one of the most widely used pieces of equipment for rainfall monitoring, being frequently used for the calibration, validation and downscaling of radar and remote sensing data, due to their major advantages–low cost, simplicity, and low energy consumption. Thus, many works have focused and continue to focus on their main disadvantage–measurement biases (mainly in wind and mechanical underestimations). However, despite arduous scientific effort, calibration methodologies are not frequently implemented by monitoring networks operators or data users, propagating bias in databases and in the different applications of such data, causing uncertainty in the modeling, management, and forecasting in hydrological research, mainly due to a lack of knowledge. Within this context, this work presents a review of the scientific advances in TBR measurement uncertainties, calibration, and error reduction strategies from a hydrological point of view, by describing different rainfall monitoring techniques in Section 2, summarizing TBR measurement uncertainties in Section 3, focusing on calibration, and error reduction strategies in Section 4, a discussion and perspectives in Section 5, and conclusions in Section 6, providing an overview of the of the state of the art and future perspectives of the technology.

Advances in remote sensing have led to use of satellite-derived rainfall products to complement the sparse rain gauge data. Although globally derived and some regional bias corrected, these products often show large discrepancies with ground measurements attributed to local and external factors that require systematic consideration. Decreasing rain gauge network however inhibits continuous validation of these products. We propose to deal with this problem by the use of Bayesian approach to merge the existing historical rain gauge information to create a consistent satellite rainfall data that can be used for climate studies. Monthly Bayesian bias correction is applied to the Climate Hazards Group Infrared Precipitation with Stations (CHIRPS v2) data to reduce systematic errors using a corresponding gridded (0.05°) rain gauge data over East Africa for a period of 33 (1981–2013) years of which 22 years are utilized to derive error fields which are then applied to an independent CHIRPS data for 11 years for validation. The bias correction is spatially and temporally assessed during the rainfall wet months of March-May (MAM), June-August (JJA) and October–December (OND) in East Africa. Results show significant reduction of systematic errors at both monthly and yearly scales and harmonization of their cumulative distributions. Monthly statistics showed a reduction of RMSD (29–56)% and MAE (28–60)% and an increase of correlations (2–32) %, while yearly ones showed reductions of RMSD (9-23)%, and MAE (7–27)% and increase of correlations (4–77)% for MAM months, reduction of RMSD (15–35)% and MAE (16–41)% and increase in correlations (5–16)% for JJA months, and reduction of RMSD (3–35)% and MAE (9–32)% and increase of correlations (3–65)% for OND months. Systematic errors of corrected data were influenced by local processes especially over Lake Victoria and high elevated areas. Large-scale circulations induced errors were mainly during JJA and OND rainfall seasons and were reduced by the separation of anomalous years during training. The proposed approach is recommended for generating long-term data for climate studies where consistencies of errors can be assumed.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Numerous experimental and theoretical studies undertaken to determine the effective-stress coefficient for seismic velocities in rocks stem from the importance of this geomechanical parameter both for monitoring changes in rock saturation and pore pressure distribution in connection with reservoir production, and for overpressure prediction in reservoirs and formations from seismic data. The present work pursues a task to determine, in the framework of a low-frequency laboratory study, the dependence of the elastic moduli of n-decane saturated sandstone on the relationship between pore and confining pressures. The study was conducted on a sandstone sample with high quartz and notable clay content in the quasi-static regime, when the 100 ml tank filled with n-decane was directly connected to the pore space of the sample. The measurements were carried out at a seismic frequency of 2 Hz and strains, controlled by semiconductor strain gauges, not exceeding 10-6. The study was performed using a forced-oscillation laboratory apparatus utilizing stress-strain relationship. The dynamic elastic moduli have been measured in two sets of experiments: at constant pore pressures of 0, 1 and 5 MPa and differential pressure (defined as a difference between confining and pore pressures) varied from 3 to 19 MPa; and at а constant confining pressure of 20 MPa and pore pressure varied from 1 to 17 MP. It was shown that the elastic moduli obtained in the measurements are in good agreement with the Gassmann moduli calculated for the range of differential pressures used in our experiments, which corresponds to the effective-stress coefficient equal to unity.

This contribution was devoted to unveil the strain rate sensitivity (SRS) of G18NiCrMo3-6 cast steel in tension/compression asymmetry. For that purpose, detailed mechanical characterization tests were conducted providing a process window covering quasi-static and medium strain rate regimes (0.001, 0.1, 10 [ s¯¹]) in tension and compression states. By means of this experimental ef-fort, the SRS of the material could be extracted by a function of strain and strain rate which ena-bling to create a mathematical expression to easily be implemented as a state variable for constitu-tive material modeling. Finally, a pressure and rate dependent constitutive material model on the basis of Cocks'89 yield locus definition was created by a subroutine (UMAT) file and the material parameters were verified with respect to the experimental data. The UMAT file also takes into account the tension/compression asymmetry in yielding to handle the effect of porous media plas-ticity concept. The predictions of the proposed material model are quite in line with the experi-mental outputs.

This study aimed to investigate the diagnostic potential of circulating microRNAs (miRNAs) for detecting early myocardial fibrosis development in HFpEF patients. This observational study used a case-control research design. Peripheral blood samples were isolated from 25 HFpEF patients and 25 normal patients. They were measured for NTproBNP levels using ELISA, as well as MicroRNA-1, 21, and 29 levels using RT-PCR. All patients also underwent echocardiography for global longitudinal strain (GLS) to measure the myocardial fibrosis progression. Data were analyzed using SPSS 25.0. HFpEF patients had significantly higher GLS compared to the normal patients (-13±2.4% vs -19±3.2%; p &lt; 0.05), suggesting HFpEF patients tended to have myocardial fibrosis. HFpEF patients also had significantly higher microRNA-1 and microRNA-21 compared to the normal patients (p &lt; 0.05), but they had lower microRNA-1 (p &lt; 0.05). There was a positive correlation between microRNA-1 (r = 0.753; p &lt; 0.05) and microRNA-21 (r = 0.675; p &lt; 0.05) and an inverse correlation with microRNA-29 (r = -0.653; p &lt; 0.05) based on the GLS findings. By using a GLS cutoff of -15% for myocardial fibrosis, microRNA-1, microRNA-21, and microRNA-29 were found to be able to predict myocardial fibrosis based on GLS with a specificity of 78% and sensitivity of 75%. Increasing microRNA-1 and microRNA-21 followed by decreasing microRNA-29 in HFpEF patients suggest early myocardial fibrosis.

The rapid changes in the coronavirus genomes are creating new strains over time after the first variation found in Wuhan in 2019. SARS-CoV-2 (Severe Acute Respiratory Syndrome Coronavirus 2) genotypes need periodically undergo whole genome sequencing. Genome sequencing has been extremely helpful in combating this virus because so many diagnoses, treatments, and vaccinations have been developed against it. To achieve this, we generated 17 high-quality whole-genome sequence data from 48 SARS-CoV-2 genotypes of COVID-19 patients who tested positive by PCR in the Tashkent city of Uzbekistan. We identified nucleotide polymorphisms, including nonsynonymous (missense) and synonymous mutations in the coding regions of the sequenced sample genomes. All whole genome sequences were categorized by phylogenetic analysis into the G clade (or GK sub-clade). A total of 134 mutations were identified, consisting of 65 shared and 69 unique mutations. Collectively, nucleotide changes represented one frameshift mutation, one conservative and disruptive insertion deletion, four upstream region mutations, four downstream region mutations, 39 synonymous mutations, and 84 missense mutations. Furthermore, bioinformatics web tools were used to analyze amino acid changes in virus genomes. Several amino acid mutations were found, which were not found in previously published Delta strain sequences.

All over the world, externally bonded fiber-reinforced polymer systems used to strengthen concrete elements improve building sustainability. However, reports issued by the American Concrete Institute Committee 440 called for heavy scrutinizing before actual field implementation. The very limited number of proposed equations lacks reliability and accuracy. Thus, further investigation in this area is needed. In addition, machine learning techniques are being implemented successfully in developing strength models for complex problems. This study aims to provide a reliable machine learning model based on an experimental database. The proposed model was developed and validated against the experimental database and the very limited models in the literature. The model showed improved agreement with the experimental results compared to the previous models.

The International System of Units (SI) was adopted in 1960 as a universal measuring system to be used for all areas of science. Sports Science papers have shown lots of inaccurate and inappropriate terms for quantification of athletes’ performance and the psychobiological responses to exercise (e.g., internal load). In biomechanics, external and internal loads are forces acting externally and internally, inducing stress and strain in the biological tissues. Therefore, the current review present simple proposals to correct the inappropriate terms: 1) do not use the term external load when referring to the assessment of exercise time, distance, displacement, speed, velocity, acceleration, torque, work, power, impulse, etc.; 2) do not use the term internal load when referring to the assessment of psychobiological stress markers (i.e., session rating of perceived exertion, heart rate, blood lactate, oxygen consumption, etc.); 3) do not use the term impulse when expressing other calculus than integrating force with respect to time, and neither strain, when expressing other phenomena than the body deformation. Instead, the term exercise intensity is universal and can be used to describe all forms of exercise. Finally, duration should precisely be described according to physical quantities (e.g., time, distance, displacement, speed, velocity, acceleration, force, torque, work, power, impulse, etc.) and the units accomplish by use of the SI. These simple quantifications can be performed for the exercises, sessions, microcycles, mesocycles and macrocycles of the athletes. Such standardization will provide a consistent and clear communication among sports scientists and all areas of science.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

The Apennine sector formed by Sannio and Irpinia is one of the most important seismic districts in Italy, representing a good case of study due to the plenty of recorded earthquakes that have therein occurred from Roman times up to nowadays. We have merged the historical record and the new satellite techniques that allow a precise determination of ground movements, and then derived physical dimensions like strain rate. In this way, we have verified that in Irpinia the hazard of new strong shocks forty years after one of the strongest known seismic events in the district is still high. This aspect must be considered very important from many points of view, particularly for Civil Protection plans, as well as civil engineering and urban planning development.

Based on the kinematic approach of the limit analysis and slip-line theories, this paper proposes a new 2D analytical model to evaluate the collapse support pressure to ensure the face stability of a circular tunnel in purely cohesive soils driven by a shield. The normality conditions, the yield criterion and the vertical soil arching effect are considered in the analytical model. Two upper bound solutions corresponding to the ratio of the cover to the diameter (C/D) are derived from considering the mechanisms based on the motion of rigid multi-blocks. Comparisons are made with existing upper and lower bound solutions published in previous articles. The results are close to the solutions of practical engineering. The failure mechanisms proposed in this study provide a better explanation for the failure process in the heading of the tunnel face.

Myocardial deformation imaging (strain imaging) is a technique to directly quantify the extent of myocardial contractility and overcomes several of the limitations of ejection fraction. The application of the most commonly used strain imaging method; speckle-tracking echocardiography to patients with sepsis cardiomyopathy heralds an exciting development to the field. However; the body of evidence and knowledge on the utility, feasibility and prognostic value of left ventricular global longitudinal strain in sepsis cardiomyopathy is still evolving. We conducted a review of literature on utility of left ventricular global longitudinal strain in sepsis cardiomyopathy. We discuss the role of left ventricular global longitudinal strain in mortality prediction, utility and limitations of the technique in the context of sepsis cardiomyopathy.

The statistics of grain displacements probability distribution function (pdf) during the shear of a granular medium displays an unusual dependence with the shear increment upscaling as recently evinced [Phys. Rev. Lett. 115 238301 2015]. Basically, the pdf of grain displacements has clear nonextensive ($q$-Gaussian) features at small scales but approaches to Gaussian characteristics at large shear window scales -- the granulence effect. Here, we extend this analysis studying a larger system (more grains considered in the experimental setup) which exhibits a severe shear band fault during the macroscopic straining. We calculate the pdf of grain displacements and the dependency of the $q$-statistics with the shear increment. This analysis have shown a singular behavior of $q$ at large scales, displaying a non-monotonic dependence with the shear increment. By means of an independent image analysis, we demonstrate that this singular non-monotonicity could be associated with the emergence of a shear band within the confined system. We show that the exact point where the $q$-value inverts its tendency coincides with the emergence of a giant percolation cluster along the system, caused by the shear band. We believe that this original approach using Statistical Mechanics tools to identify shear bands can be a very useful piece to solve the complex puzzle of the rheology of dense granular systems.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

In this study, the model proposed by Yang et al. to generalize the stress–strain model for unconfined concrete with consideration of the size effect is expanded. Sim et al.’s compressive strength model that is based on the function of specimen width and aspect ratio was used for the maximum stress. In addition, a strain at the maximum stress was formulated as a function of compressive strength by considering the size effect using the regression analysis of datasets compiled from a wide variety of specimens. The descending branch after the peak stress was formulated with consideration of less dissipated area of fracture energy with the increase in specimen width and aspect ratio in the compression damage zone (CDZ) model. The key parameter for the slope of the descending branch was formulated as a function of specimen width and aspect ratio, concrete density, and compressive strength of concrete considering the size effect. Consequently, a rational stress–strain model for unconfined concrete was proposed. This model explains the trends of the peak stress and strain at the peak stress to decrease and the slope of the descending branch to increase, as the specimen width and aspect ratio increase. The proposed model agrees well with the test results, irrespective of the compressive strength of concrete, concrete type, specimen width and aspect ratio. In particular, the proposed model for the stress–strain curve rationally considered the effect of decreasing peak stress and increasing the descending branch slope, with the increase in specimen width and aspect ratio.

To date, several independent methods and algorithms exist exploiting constraint-based stoichiometric models to find metabolic engineering strategies that optimize microbial production performance. Optimization procedures based on metaheuristics facilitate a straightforward adaption and expansion of engineering objectives as well as fitness functions, while being particularly suited for solving problems of high complexity. With the increasing interest in multi-scale models and a need for solving advanced engineering problems, we strive to advance genetic algorithms, which stand out due to their intuitive optimization principles and proven usefulness in this field of research. A drawback of genetic algorithms is that premature convergence to sub-optimal solutions easily occurs if the optimization parameters are not adapted to the specific problem. Here, we conducted comprehensive parameter sensitivity analyses to study their impact on finding optimal strain designs. We further demonstrate the capability of genetic algorithms to simultaneously handle (i) multiple, non-linear engineering objectives, (ii) the identification of gene target-sets according to logical gene-protein-reaction associations, (iii) minimization of the number of network perturbations, and (iv) the insertion of non-native reactions, while employing genome-scale metabolic models. This framework adds a level of sophistication in terms of strain design robustness, which is exemplarily tested on succinate overproduction in Escherichia coli.

Carbon nanotube (CNT) yarns are fiber-like materials that exhibit excellent mechanical, electrical and thermal properties. More importantly, they exhibit a piezoresistive response that can be tapped for sensing purposes. The objective of this study is to determine experimentally the piezoresistive response of CNT yarns that are embedded in a polymeric medium while subjected to either compression or tension, and compare it with that of the free or unconstrained CNT yarns. The rationale for this study is the need to know the response of the CNT yarn while in a medium, which provides a lateral constraint to the CNT yarn thus mimicking the response of integrated CNT yarn sensors. The experimental program will include the fabrication of samples and their electromechanical characterization. The CNT yarns are integrated in polymeric beams and subjected to four-point bending, allowing the determination of their response under tension and compression. The electrical resistance data from an Inductance-Capacitance-Resistance (LCR) device is used with the data acquired from the mechanical testing system to determine the piezoresistive response of the CNT yarns. This data and information will be used for future modeling efforts and to study the phenomena that occur when CNT yarns are integrated in polymeric and composite materials and structures.

The stability of deep soft rock tunnels is of particular concern under seepage conditions. Aiming at thoroughly discussing the seepage actions and their consequences on the support scheme of such structures, the host rocks of the Weilai Tunnel situated in Guangxi province of China are taken as the research substance. Emphasizing on seepage conditions, stresses, displacements and plastic zone radii along the surrounding rocks of such tunnel are adequately examined taking into consideration the Mogi-Coulomb strain criterion and the elastic-plastic theory. Subsequently, based on strain-softening model, the coupled actions of seepage and softening on the rocks surrounding the tunnel are studied. According to the results, it is revealed that the support scheme of deep soft rock tunnels must be of highest resistance possible to better decrease the plastic zone and the tangential stress along the host rocks. Moreover, throughout the surrounding rocks, the dissemination of pore water pressure is strongly affected by the uneven permeability coefficient under anisotropic seepage states. Combined effects of softening and seepage are very dangerous for the surrounding rocks of deep-buried tunnels. To better guarantee reasonable longevity of such tunnels, long-term monitoring of their support structures with reliable remote sensors is strongly recommended.

The Standard Model (SM) of particle physics successfully describes electromagnetic, weak, and strong forces but omits gravity. We introduce the Kinematrix Field Theory (KFT), integrating gravity into this fundamental force framework through a novel particle, the kinematon. This gauge boson, existing in both massless and massive forms, advances the SM's scope to address enigmas like dark matter and neutrino masses. We detail the mathematical structure of the KFT and establish Feynman rules for kinematon interactions with fermions and gauge bosons. The KFT, synergizing with the Higgs mechanism and general relativity, aspires to a unified quantum theory of gravity. We explore the kinematon's phenomenological implications and potential experimental signatures, forecasting significant advancements in fundamental physics and setting a course for future explorations in the SM.

In this paper, we investigated the capacitive effect and the electromagnetic coupling on the measurement chain induced by the gas gun or the powder gun during impact experiments. Reduced bandwidth and noise have been noticed on experimental signals. Rogowski coil measurements have been added on the cables to characterize the electromagnetic coupling. The perturbation currents on the cables have been quantified depending on the configuration. The gauge, the transmission line and the conditioning system have been modeled. The calculations have reproduced the electrical wave arrival time, the transmission line transfer impedance, the conditioning system transfer impedance and it shows the bandwidth limitation. A capacitive effect with the piezoresistive manganin gauge embedded into the sample has been identified depending on the experimental setup.

Accurate knowledge of the rain amount is an crucial driver in several hydro-meteorological applications. This is especially true in complex orography territories, which are typically impervious, thus leaving ungauged most of the mountain areas. Thanks to their spatial and temporal coverage, weather radars can potentially overcome such an issue. However, weather radar, if not accurately processed, can suffer from several limitations (e.g., beam blocking, altitude of the observation, path attenuation, indirectness of the measurement) that can hamper the reliability of the rain estimates performed. In this study, a comparison between rain gauge and weather radar retrievals is performed in the target area of the Abruzzo region in Italy, which is characterized by a heterogeneous orography ranging from the sea side to Apennine ridge. Consequently, the Abruzzo region has an inhomogeneous distribution of the rain gauges, with station density decreasing with the altitude reaching up to approximately 1500 m a.s.l. Notwithstanding, pluviometric inflow spatial distribution shows a sub-regional dependency as a function of four climatic and altimetric factors: coastal, hilly, mountain, and inner plain areas (i.e., Marsica). Such areas are used in this analysis to characterize the radar retrieval vs. rain gauge amounts in each of those zones. Compared to previous studies on the topic, the analysis presented an attention to the importance of an accurate selection of the climatic and altimetric sub-regional areas where undertake the radar vs. rain gauge comparison. This aspect is not only of great importance to correct biases in radar retrievals in a more selective way, but it also paves the way for more accurate hydro-meteorological applications (e.g., hydrological model initialization, quantify the aquifers recharge etc.) which, in general, require the accurate knowledge of rain amounts upstream of a basin. To fill the gap caused by the uneven rain gauge distribution, Ordinary Kriging has been applied on a regional scale to obtain 2D maps of rainfall data, which are cumulated on a monthly and yearly base. Weather radar data from the Italian mosaic are considered as well, in terms of rain rate retrievals and cumulations performed on the same time frame used for rain gauges. The period considered for the analysis is two continuous years: 2017 and 2018. The output of the elaborations are raster maps for both radar and interpolated rain gauges, where every pixel contains a rainfall quantity. Although the results show a general underestimation in the weather radar data especially in mountain and Marsica areas, even though within the 95% confidence interval of the OK estimation. Our analysis highlights that the average bias between radar and rain gauges, in terms of precipitation amounts, is a function of altitude and is almost constant in each of the selected areas. This achievement suggests that after a proper selection of homogeneous target areas, the radar retrievals can be corrected using the denser network of rain gauges typically distributed at lower altitudes and extend such correction at higher altitudes without loss of generality.

Precipitation is a crucial driver for many environmental processes and weather radars are capable of providing precipitation information with high spatial and temporal resolution. However, radar-based quantitative precipitation estimates (QPE) are also subject to various potential uncertainties. This study explores the development, uncertainties and potentials of the hourly operational German radar-based and gauge-adjusted QPE called RADOLAN and its reanalysed radar climatology dataset named RADKLIM in comparison to ground-truth rain gauge data. The precipitation datasets are statistically analysed across various time scales ranging from annual and seasonal aggregations to hourly rainfall intensities in regard to their capability to map long-term precipitation distribution, to detect low intensity rainfall and to capture heavy rainfall. Moreover, the impacts of season, orography and distance from the radar on long-term precipitation sums are examined in order to evaluate dataset performance and to describe inherent biases. Results revealed that both radar products tend to underestimate total precipitation sums and particularly high intensity rainfall. But our analyses also showed significant improvements throughout the RADOLAN time series as well as major advances through the climatologic reanalysis regarding the correction of typical radar artefacts, orographic and winter precipitation as well as range-dependent attenuation.

We show that the Einstein field equations for a five-dimensional warped spacetime, where only gravity can propagate into the bulk, determine the dynamical evolution of the warp factor of the four-dimensional brane spacetime. This can be explained as a holographic manifestation. The warped 5D model can be reformulated by considering the warp factor as a dilaton field ($\omega$) conformally coupled to gravity and embedded in a smooth $M_4 \otimes R$ manifold. On the brane, where the U(1) scalar-gauge fields live, the dilaton field manifests itself classically as a warp factor and enters the evolution equations for the metric components and matter fields. We write the Lagrangian for the Einstein-scalar-gauge fields in a conformal invariant setting. However, as expected, the conformal invariance is broken (trace-anomaly) by the appearance of a mass term and a quadratic term in the energy-momentum tensor of the scalar-gauge field, arising from the extrinsic curvature terms of the projected Einstein tensor. These terms can be interpreted as a constraint in order to maintain conformal invariance. By considering the dilaton field and Higgs field on equal footing on small scales, there will be no singular behavior, when $\omega\rightarrow 0$ and one can deduce constraints to maintain regularity of the action. Our conjecture is that $\omega$, alias warp factor, has a dual meaning. At very early times, when $\omega \rightarrow 0$, it describes the small-distance limit, while at later times it is a warp (or scale) factor that determines the dynamical evolution of the universe. We also present a numerical solution of the model and calculate the (time-dependent) trace-anomaly. The solution depends on the mass ratio of the scalar and gauge fields, the parameters of the model and the vortex charge $n$.

Many reported sea level records are often not a single measurement. They are then a composition of different records from several tide gauges. Sometimes, they are from the same tide gauge, but the tide gauge stability has been affected by earthquakes. This is the case of Guam as discussed in the present manuscript. The claimed sea level acceleration of Guam is only the result of two earthquakes that have compromised the stability of the tide gauge.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Myocardial involvement among critical patients with coronavirus disease 2019 (COVID-19) has a worse outcome. The occurrence of an imbalance in oxygen supply results in the release of pro-inflammatory cytokines which leads to increased ventilation support requirement and increase risk of mortality. Our aim was to evaluate the association between hs-Troponin I level and global longitudinal strain as evidence of myocardial involvement among critical COVID-19 patients. Methods. We performed prospective cohort study from February 1st – July 31st, 2021 at Dr. Soetomo General Hospital, Surabaya as referral center for COVID-19 care. Of the 65 critical COVID-19 included, 41 (63.1%) were men, with a median (interquartile range) age of 51.0 years (20.0-75.0).Subjects were recruited according to WHO criteria for severe COVID-19 and CDC criteria for myocarditis. All subjects recruited were examined using echocardiography to measure global longitudinal strain (GLS) and blood samples were taken to measure hs-Troponin. Subjects were then followed to assess their needs for mechanical ventilation and in-hospital mortality. Severe COVID-19 subjects with cardiac injury were associated with an increased need for intubation (78.5%) and an increased incidence of myocarditis (50.8%). There was an association between the use of intubation and the risk of mortality in patients (66.7% vs. 33.3%, p-value &lt;0.001). Both reduced GLS and increased hs-troponin are associated with increased myocarditis (p-value &lt;0.001 and 0.004 respectively). Reduced GLS is associated with higher mechanical ventilation needs (12.17 + 4.79 vs.15.65 + 4.90, p-value 0.02) and a higher mortality rate (11.36 + 4.64 vs. 14.74 + 4.82; p-value 0.005). Increased hs-troponin is associated with higher mechanical ventilation needs (25.33% vs. 3.56%, p-value 0.002) and a higher mortality rate (34.57% vs. 5.76%, p-value 0.002). Compared with contemporary controls, critical COVID-19 patients with myocardial involvement and elevated cardiac troponin level are associated with higher mechanical ventilation needs and a higher mortality rate.

This study investigates the microstructures and deformation mechanism of hetero-structured pure titanium under different high strain rates (500 s-1，1000 s-1，2000 s-1). The influence of strain rate on the deformation mechanism is examined. As the strain rate increases, the dominance of dislocation slip decreases while deformation twinning becomes more prominent. Notably, at a strain rate of 2000s-1, nanoscale twin lamellae are activated within grain with a size of 500nm, which is a rarely observed phenomenon in pure Ti. Additionally, martensitic phase transformation is also identified. These findings can greatly enhance our understanding of the mechanical responses of Ti and broaden the potential applications of Ti in dynamic deformation scenarios.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

Research has been actively conducted on the materials used to commercialize finished products that use hydrogen energy. Hydrogen embrittlement that occurs when hydrogen atoms penetrate metals is the largest problem that must be addressed first regarding safety. Because liquefied hydrogen has an 800 times higher density than hydrogen gas, hydrogen has been stored and transported through liquefaction at -253℃ using helium gas as a refrigerant. However, even if extreme temperatures below zero are maintained, natural vaporization loss that reduces liquefied hydrogen by 3 to 5% of the tank storage capacity per day occurs. In addition, when liquefied hydrogen is converted into high-pressure hydrogen gas for use, it is difficult to completely prevent the loss of the gas, even if sealing technology is applied to prevent gas leaks in transport and storage tanks. Therefore, methods to minimize the loss of hydrogen, establishment of assessment criteria for the embrittlement caused by a small amount of hydrogen gas, and related research are essential. We researched the hydrogen embrittlement resistance of SUS316L rods according to the tensile speed by conducting water electrolysis testing at room temperature, at which hydrogen gas is used to present hydrogen embrittlement assessment criteria for primary ring-shaped forged products.

We present the results of a twofold experimental and computational study of (0001) GaN/AlN multilayers forming pseudomorphic superlattices. High-Resolution Transmission Electron Microscopy (HRTEM) shows that heterostructures with GaN Quantum Wells (QW) four c-lattice parameters thick are misfit-dislocation free. Accurate structural data are extracted from HRTEM images via a new methodology optimizing the residual elastic energy stored in the samples. Total energy calculations are performed with several models analogous to the experimental QWs with increasing thicknesses of GaN, whereas this of the AlN barrier is kept fixed at n=8 c-lattice parameters. With vanishing external stresses, minimum energy configurations of the studied systems correspond to different strain states. Linear elasticity accurately yields the corresponding lattice parameters, suppressing the need for on-purpose total energy calculations. Theoretically justified parabolic fits of the excess interfacial energy yield the values of interfacial stress and elastic stiffness as functions of the GaN QW thickness. Total species-projected densities of states and gap values extracted therefrom allow deciphering the effect of the evolving strain on the electronic structure of the superlattice. It is found that the gap energy decreases linearly with increasing the strain of the QW. These results are briefly discussed in the light shed by previous works from the literature.

This paper presents a finite element analysis of the bi-directional orthogonal model, which incorporates individual crack strain separation and tracking. The objective of the research is to expand the current shear friction model to manage bi-directional cracking at any angle, allowing for a more universal model that can be applied to intricate structures and non-proportional loading cases. The proposed model was initially developed as a total strain-based model, with the assumption that crack strains are equivalent to total strains, but was subsequently recalculated to improve accuracy by separating crack strains from total strains. Furthermore, a separate crack strain formulation was created to account for strains in the concrete's uncracked portions and locked-in crack strains. The article then discusses the testing of various convergence methods and loading programs to achieve high convergence. Comparative analyses of the generalized shear friction model with other models for crack orientation and loading cases similar to those of a reinforced concrete membrane are also presented. The MATLAB program successfully applied the bi-directional cracking model for one finite element under a uniform cyclical strain state, using a secant stiffness formulation.

The mass production of mosquitoes at an industrial scale requires efficient sex separation, which can be achieved through mechanical, genetic or artificial intelligence means. Compared with others methods, the genetic sexing approach offers the advantage of limiting costs and space by removing females at larval stage. We recently developed a GSS in Aedes albopictus based on the sex linkage of the rdl gene to the M locus, conferring dieldrin resistance in males only. It has been previously reported that dieldrin ingested by larvae can be detected in adults and bioaccumulated in predators, raising the question of its use at a large-scale. In this context, we performed several experiments aiming at optimizing dieldrin selection by decreasing both dieldrin concentration and exposure time while maintaining a stable percentage of females averaging 1%. We showed that the previously used dieldrin exposure induced an important toxicity as it killed 60% of resistant males at larval stage. We could easily lower this toxicity by reducing the dose and/or the exposure time to recover nearly all resistant males. We then quantified the residues of dieldrin in resistant male adults and showed that dieldrin toxicity in larvae was positively correlated with dieldrin concentrations detected in adults. Interestingly, we showed that the use of reduced dieldrin exposure led to a dieldrin detection in adult males that was below the sensitivity threshold of the Gas Chromatography Mass Spectrometry detection method. Presented data show that dieldrin exposure can be adjusted to suppress toxicity in males while achieving efficient sexing and lowering the levels of dieldrin residues in adults to barely detectable levels.

The perceived risk of being infected at work (PRIW) with COVID-19 represents a potential risk factor for workers during the current COVID-19 pandemic. In line with the job demands-resources (JD-R) model applied to safety at work, in this longitudinal study we propose that PRIW can be conceptualized as a job demand, whereas communication (i.e., the exchange of good-quality information across team members) can be conceived as a job resource. Accordingly, we hypothesized that PRIW at Time 1 (T1) would positively predict psychophysical strain at Time 2 (i.e., four months later). Furthermore, we hypothesized that communication at T1 would negatively predict psychophysical strain at T2. Overall, 297 workers took part in the study. The hypothesized relationships were tested using multiple regression analysis. Results supported our predictions: PRIW positively predicted psychophysical strain over time, whereas communication negatively predicted psychophysical strain over time. Also, results did not change after controlling for age, gender, and type of contract. Overall, this study suggests that PRIW and communication can be considered as a risk and a protective factor for work-related stress, respectively. Hence, to promote more sustainable working conditions, interventions should encourage organizations to optimize the balance between job demands and job resources related to COVID-19.

In the present work, cost-effective strain gauges were fabricated by using inkjet printing and photonic curing on flexible and recyclable PET substrates. Ohmic resistance (a.k.a. DC resistance) (R0) and complex electrical impedance (Z) as a function of test frequency were characterized, respectively, with the state-of-the-art electronic testing equipments. For the fabrication process, commercially available silver nanoparticle (AgNP) inks and printing substrates were used in order to eliminate any apriori ink processing. In order to validate the in-house cantilever beam measurement setup and devices, first, commercially available metallic foil strain gauges (with the provided gauge factor GF=2 by the manufacturer) were tested at different locations. Thereafter, the printed strain gauges were investigated with several repetitions at different measurement locations. The measurement results demonstrated an affordable, rapid and tailorable design and repeatable fabrication approach for strain gauges with GFavg~6.6, which has potential applications in remote sensing and structural monitoring applications.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

We describe the effect of the expansion of space on the wavelength of the light beam in a Fabry-Pérot interferometer. For an instrument such as the Laser Interferometer Gravitational-Wave Observatory (LIGO), which has high sensitivity and a long period of light storage, the wavelength ${\lambda }_L$ of laser photons are redshifted due to the expansion of space in each cavity by an amount $\delta \lambda$ given by $\delta \lambda /{\lambda }_L=H_0{\tau }_s\approx 8.8\times {10}^{-21}$ , where $H_0\approx 2.2\times {10}^{-18}{\mathrm{s}}^{-1}$ is the Hubble constant and ${\tau }_s\approx 4\mathrm{ms}$ is the light storage time for the cavity. Since ${\tau }_s$ is based on the cavity finesse $\mathcal{F}$ which depends on the laser beam full width at half maximum (FWHM) $\delta \omega$ of each cavity, we show that a difference in finesses between the LIGO arm cavities produces a signal $h_H\left(t\right)$ at the anti-symmetric output port given by $h_H\left(t\right)=2a_1{H}_0\left(\frac{1}{\delta {\omega }_X\left(t\right)}-\frac{1}{\delta {\omega }_Y\left(t\right)}\right),$ where $\delta {\omega }_X\left(t\right)$ and $\delta {\omega }_Y\left(t\right)$ are the beam FWHM at time t, respectively, for the X and Y arm cavities and $a_1$ is a beam proportionality constant to be determined expermentally. Assuming $a_1\approx 1$ , then for cavity beams FWHM of $\delta \omega \left(t\right)\approx (523.2\pm 31)\mathrm{rad}.{\mathrm{s}}^{-1}$ the output signal has the range $\mid h_H\left(t\right)\mid \le 1\times {10}^{-21}$ , which is detectable by advanced LIGO.

The field dynamics of neutral and charged matter (treated as gauge fields) beyond the event horizon of black holes are investigated. As an extension of the work done in Ganesan (2023) [1], the analysis was done using the combined dynamics of the two-dimensional Yang-Mills and Liouville gravity fields beyond the event horizon. The quantum interactions and symmetry breaking mechanisms of the combined two-dimensional fields are discussed. The second part of this paper explores the quantum dynamics occurring at the event horizon. By considering the structure of the event horizon as a Möbius strip (embedded in three-dimensional space), a formulation for the lower bound of the first energy eigenvalue of a quantum particle (electron) at the event horizon is obtained.

The problem of fluid dynamics can be greatly simplified if, for every point in space, the strain-rate tensor is diagonalized. This tensor is introduced into the Navier-Stokes equations via material law and divergence of the stress tensor. This article shows that local SO(3)xU(1) gauge fields can be used to locally diagonalize the diffusion components of the strain-rate tensor. The gauge fields resulting from the connection can be interpreted as convection components of the flow, they show properties of quasiparticles and can be interpreted as elementary vortices. Thus, the proposed approach not only offers new insights for the solution and situative simplification of the Navier-Stokes equations, it also uncovers hidden symmetries within the flow convection, allowing - depending on boundary conditions - further interpretation.

Precipitation gauges are critical for measuring precipitation rates at regional and global scales and are often used to calibrate precipitation rates estimated from other instruments such as satellites. However, precipitation measured at the gauges is affected by gauge-undercatch that is often larger for solid precipitation. In the present work, two popular gauge-undercatch correction factors are assessed: one utilizes a dynamic correction model and is used in the Global Precipitation Climatology Centre (GPCC) Monitoring product and the other one employs a fixed climatology and is used in the Global Precipitation Climatology Project (GPCP) product. How much the choice of correction factors can impact the total estimate of precipitation was quantified over land at seasonal, annual, regional, and global scales. The correction factors are also compared as a function of the environmental variables used in their development, among those are near-surface air temperature, relative humidity, wind speed, elevation, and precipitation intensity. Results show that correction factors can increase the annual precipitation rate based on the gauges by ~9.5 % over the global land (excluding Antarctica), although this amount can vary from ~6.3% (in boreal summer) to more than 10% (in boreal winter), depending on the season and the method used for gauge-undercatch correction. Annual variations of correction factors can also be large, so the use of the fixed climatology correction factors requires caution. Given their magnitudes and differences, selection of appropriate correction factors can have important implications in refining the water and energy budget calculations.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

Particles and photons appear to be total opposites; the former has rest mass which requires space to exist; the latter has kinetic energy which requires time to occur (oscillate). But they do share certain properties (e.g., quantization) that remain invariant when one is transformed (swapped) for the other. This gauge invariance is developed in some detail.The symmetry between particle and photon turns out to be one of inversion. It is the equalities of special relativity that support this inversion and the accompanying invariances: mass transformed to energy; space transformed to time. The great advantage of these symmetries (inversions) is that they provide guidance for an object little understood (the photon) based upon an object well understood (the particle). On this basis, progress can be made in the understanding of some long-standing issues: wave-particle duality, time’s arrow, the constant speed of light and nonlocality.

There has been observational evidence about spin axes of quasars in large quasar groups correlated over hundreds of Mpc. This is seen in the radio spectrum as well as in the optical range. There is not yet a satisfactory explanation of this "spooky" alignment. This alignment cannot be explained by mutual interaction at the time that quasars manifest themselves optically. A cosmological explanation could be possible in the formation of superconducting vortices (cosmic strings) in the early universe, just after the symmetry-breaking phase of the universe. We gathered from the NASA/IPAC and SIMBAD extragalactic databases the right ascension, declination, inclination, position angle and eccentricity of the host galaxies of 3 large quasar groups to obtain the azimuthal and polar angle of the spin vectors. The alignment of the azimuthal angle of the spin vectors of quasars in their host galaxy is confirmed in the large quasar group U1.27 and compared with two other groups in the vicinity, i.e., U1.11 and U1.28. It is well possible that the azimuthal angle alignment fits the predicted azimuthal angle dependency in the theoretical model of the formation of general relativistic superconducting vortices, where the initial axially symmetry is broken just after the symmetry breaking of the scalar-gauge field.} \keyword{quasar groups; alignment spin vectors; host galaxy; cosmic strings; symmetry breaking; scalar-gauge field.

Tanning, crucial for leather production, relies heavily on chromium yet poses risks due to chromium's oxidative conversion, leading to significant wastewater and solid waste generation. Physico-chemical methods are typically used for heavy metal removal, but they have drawbacks, prompting interest in eco-friendly biological remediation techniques like biosorption, bioaccumulation, and biotransformation. The EU Directive (2018/850) mandates alternatives to landfilling or incineration for industrial textile waste management, highlighting the importance of environmentally conscious practices for leather products' end-of-life management, with com-posting being the most researched and viable option. This study aimed to isolate microorganisms from tannery wastewater and identify those responsible for different types of tanned leather biodegradation. Using a leather biodegradation assay (ISO 20136) with tannery and municipal wastewaters as inoculum, bacterial shifts during leather biodegradation were observed. Over 10,000 bacterial species were identified in all analyzed samples, with 8 bacterial strains isolated from tannery wastewater. Identification of bacterial genera like Acinetobacter, Brevundimo-nas, and Mycolicibacterium provides insights into potential microbial candidates for enhancing leather biodegradability, wastewater treatment, and heavy metal bioremediation in industrial applications.

In recent years, strain sensors have penetrated various fields. The capability of sensors to convert physical signals into electrical signals is of great importance in healthcare. However, it is still challenging to obtain sensors with high sensitivity, large operating range and low cost. In this paper, a stretchable strain sensor made of a double-layer conductive network, including a biomimetic multilayer graphene-Ecoflex (MLG-Ecoflex) substrate and a multilayer graphene-carbon nanotubes (MLG-CNTs) composite up-layer was developed. The combined action of the two layers led to an excellent performance with an operating range of up to 580% as well as a high sensitivity (gauge factor (GFmax) of 1517.94). In addition, a pressure sensor was further designed using the bionic vein-like structure with a multi-layer stacking of MLG-Ecoflex/MLG-CNTs/MLG-Ecoflex to obtain a relatively high deformation along the direction of thickness. The device presented a high sensing performance (up to sensitivity of 0.433 kPa-1), capable of monitoring small movements of the human body such as vocalisations and gestures. The good performance of the sensors together with a simple fabrication procedure (flip-molding) make it potential for some applications, for example, human health monitoring and other areas of human interaction.

Environmentally friendly lead-free K1-xNaxNbO3 (KNN) ceramics possess electromechanical properties comparable to lead-based ferroelectric materials, but cannot meet the needs of device miniaturization, and the corresponding thin films lack of theoretical and experimental studies. To this end, we developed the nonlinear phenomenological theory for ferroelectric materials to study the effects of non-equiaxed misfit strain on the phase structure, electromechanical properties and electrical response of K0.5Na0.5NbO3 epitaxial films and constructed the in-plane misfit strain (u1-u2) phase diagrams. The results show that K0.5Na0.5NbO3 epitaxial film under non-equiaxed in-plane strain can exhibit abundant phase structures, including orthorhombic a1c, a2c and a1a2 phases, tetragonal a1, a2 and c phases, and monoclinic r12 phases. Moreover, in the vicinity of a2c-r12, a1c-c and a1a2-a2 phase boundaries, K0.5Na0.5NbO3 epitaxial films exhibit excellent dielectric constant ε11, while at a2c -r12 and a1c-c phase boundaries large piezoelectric coefficient d15 is observed. It was also found that high permittivity ε33 and piezoelectric coefficients d33 exist near the a2c - a2, r12- a1a2 and a1c-a1 phase boundaries due to the existence of polymorphic phase boundaries (PPB) in the KNN system, which makes it easy to polarize near the phase boundaries, and the polarizability changes suddenly, leading to electromechanical enhancement. In addition, the results show that the K0.5Na0.5NbO3 thin films possess a large electrocaloric response at the phase boundary at the r12-a1a2 and a1c-a1 phase boundaries. And the maximum adiabatic temperature change ∆T is about 3.62 K when the electric field change is 30 MV/m at room temperature, which is significantly enhanced compared with equiaxed strain. This study provides theoretical guidance for obtaining K1-xNaxNbO3 epitaxial thin films with excellent properties.

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. How-ever, challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investiga-tion of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for mo-tion capture for medical devices. Several variables were considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through experimental evaluation, by determining the gauge factor, its non-linearity, hysteresis and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50 %, 12,5 % hysteresis, and 0.3 % nonlinearity in parts.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

A highly sensitive strain sensor based on tunable cascaded Fabry-Perot interferometers (FPIs) is proposed and experimentally demonstrated. Cascaded FPIs consist of a sensing FPI and a reference FPI which effectively generate the Vernier Effect (VE). The sensing FPI comprises a hollow core fiber (HCF) segment sandwiched between single-mode fibers (SMFs), and the reference FPI consists of a tunable air reflector, which is constituted by a computer programable fiber holding block to adjust the desired cavity length. Simulation results predict the dispersion characteristics of modes carried by HCF. The sensor’s parameters are designed corresponding to a narrow bandwidth range, i.e., 1530 nm to 1610 nm. Experimental results demonstrate that the proposed sensor exhibits optimum strain sensitivity of 23.9 pm/με in the range of 0 to 3000 με which is 13.73 times higher than the single sensing FPI strain sensitivity of 1.74 pm/με. The strain sensitivity of the sensor can be further enhanced by extending the source bandwidth. The proposed sensor exhibits ultra-low temperature sensitivity of 0.49 pm/°C in the wider temperature range of 25 °C to 135 °C, providing good isolation for eliminating cross-talk between strain and temperature. The sensor is very robust, cost-effective, easy to manufacture, repeatable, and shows a highly linear and stable response in the wider range of axial strain. Based on the sensor’s performance, it may suit plenty of practical applications in the real sensing world