Interface solar steam generation (ISSG) are charming for its applications in desalination and wastewater treatment. Biomass is an attractive substrate for utilizing solar vapor evaporators because of its natural pore structure and water transportability. Polymers like polydopamine (PDA) and polypyrrole (PPy) with broadband spectrum absorption are fascinating in photothermal materials (PTMs). Herein, PDA coated daikon-based (PDA-DK) and PPy coated daikon-based (PPy-DK) PTMs have been exploited for solar steam generation. When polyethylene foam (PEF) was used as an insulating layer to limit heat loss from the PTMs to bulk water, the evaporation rate of PDA-DK and PPy-DK was raised from 0.82 kg m–2 h–1 and 0.96 kg m–2 h–1 to 1.50 kg m–2 h–1 and 1.60 kg m–2 h–1, respectively. Meanwhile, the corresponding photothermal conversion efficiency was increased to 89.01% and 98.97%, which was increased by nearly 40% under 1-sun irradiation. In addition, PDA-DK and PPy-DK exhibited remarkable stability for the solar steam generation without significant change through 15 cycles. Furthermore, PDA-DK and PPy-DK could effectively desalt seawater and purify dyeing wastewater. All the results indicate that PDA-DK and PPy-DK have great potential in real-world applications for solar steam generation.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

The global increase in population, the phenomenon of climate change, the issue of water pollution and contamination, and the inadequate management of water resources all exert heightened strain on freshwater reserves. The potential utilization of the interfacial solar steam generation (ISSG) system, which utilizes photothermal conversion to generate heat on material surfaces for wastewater purification and desalination purposes, has been successfully demonstrated. Textile materials based ISSG devices, including (woven, nonwoven and knitting) fabrics and electrospinning membranes, exhibit distinct properties such as rough surface texture, high porosity, significant surface area, exceptional flexibility, and robust mechanical strength. These characteristics, combined with their affordability, accessibility, and economic viability for widespread implementation, make them extremely attractive for applications in SSG. In this review, a comprehensive analysis of emerging concepts, advancements and applications of textile materials (woven, nonwoven, and knitting) fabrics and electro-spun membranes in the ISSG for wastewater purification and desalination is highlighted. We also emphasize significant obstacles and potential prospects in both theoretical investigations and real-world implementations, aiming to contribute to future advancements in the domain of textile based materials interfacial evaporation in wastewater purification and desalination. Furthermore, the drawbacks and the challenges of ISSG systems are also highlighted.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

This article explores the lack of unanimity regarding the nomenclature used to refer to the field of research that explores the intersection between art and science. A series of examples of nomenclatures and the context in which they are applied are listed and referenced. The diverse terminology reflects the heterogeneity, transdisciplinarity, and complexity of a research field in full expansion.

The research is based on the question: Can teaching/learning methodologies help to achieve the objective of Sumak Kawsay in Ecuador? a STEAM work approach was applied in technical high school students and higher education students (technological), in order to determine the level of impact in terms of project generation, following the entire process, from the generation of ideas to the linking of projects with society, The analysis was carried out in students from 15 to 22 years old in two institutions in the city of Cuenca, using the method of intentional sampling and the systematic review of scientific articles in the Scopus and Google academic databases of the last 3 years, to determine the level of impact of the prototypes pub-lished in indexed journals. The most striking aspect of the results is that of the 260 students surveyed, only 19.6% of students consider that there are STEAM teachers in the classroom, and only 56.92% of students manage to link their work with society, one of the recommended strategies being the publication of scientific articles and participation in congresses disseminating the high impact work done by students in the classroom.

Children are inherently curious about everything they encounter, making the early years a perfect time for STEAM (science, technology, engineering, arts, and math) investigations. An outdoor learning environment can influence STEAM concept formation of preschoolers with intentional design that offer STEAM learning affordances. Despite the rising interest in early STEAM education, there is still limited literature on how the outdoor environment may influence STEAM learning behaviors of preschoolers (3-5 years old). This scoping review intends to evaluate the existing knowledge regarding the physical factors that contribute to STEAM learning affordances in an outdoor environment for children aged 3 to 5. The review included studies from the last twenty years. This scoping review was conducted in accordance with the criteria outlined in the Preferred Reporting Items for Systematic Reviews and Meta-Analyses Extension for Scoping Reviews (PRISMA-ScR). For this scoping review, 843 citations were discovered across four databases (JSTOR, Scopus, EBSCOhost, and Web of Science), ProQuest, and Google Scholar, and 31 articles were considered eligible for inclusion. Through the synthesis of information from those 31 studies, a list of STEAM learning behaviors of children and STEAM activity-supportive settings were identified that may positively influence preschoolers' STEAM concept development.

This research aims to delve into the intricacies of combustion processes, specifically focusing on heating oil and a blend of heating oil with TPO (Tire Pirolysis Oil) in a self-developed evaporative combustion chamber featuring steam injection. The primary objective is to scrutinize the impact of steam injection on the combustion dynamics. Conducting a series of tests, the investigation involved the meticulous manipulation of stoichiometric ratios while introducing ambient air through gravity fuel flow. Subsequent iterations of these tests incorporated the introduction of steam into the ambient air stream. The examination encompassed the combustion of both heating oil and the TPO blend within the combustion chamber. The evaluation criteria comprised an in-depth analysis of flame characteristics, temperature distribution within the combustion chamber, and the quantification of emissions such as particulate matter (PM), nitrogen oxides (NOx), carbon dioxide (CO2), carbon monoxide (CO), and water vapor (H2O). Throughout the experimentation phase, commercially available diesel fuel served as the primary fuel source. To facilitate the tests, the combustion chamber under scrutiny was seamlessly integrated into an AVL engine test bench system. Essential parameters, including fuel consumption, were meticulously gauged using an AVL 735 fuel flow meter, while fuel temperature was monitored using the AVL 745 fuel temperature conditioning system. The intake air, a crucial element in the combustion process, was quantified with precision using an AVL Flowsonix sensor. Emission measurements were conducted meticulously using state-of-the-art equipment, with gaseous emissions analyzed using an AVL FTIR AMA i60 exhaust gas analyzer. Simultaneously, soot emissions were quantified through employment of an AVL Micro Soot sensor. This comprehensive approach not only delves into the fundamental aspects of combustion but also extends its reach to the exploration of innovative techniques, such as steam injection, to enhance combustion efficiency and reduce emissions. The integration of advanced measurement tools ensures a robust and thorough analysis of the combustion process and its environmental implications.

Boiler efficiency is called to some extent of total thermal energy which can be recovered from the fuel. Boiler efficiency losses are due to four major factors: the dry gas flux, the latent heat of steam in the flue gas, the combustion loss or the loss of unburned fuel, radiation and convection losses. In this research, the thermal behavior of boilers in gas refinery facilities is studied and their efficiency and their losses are calculated. The main part of this research is comprised of analyzing the effect of various parameters on efficiency such as excess air, fuel moisture, air humidity, fuel and air temperature, the temperature of combustion gases, and thermal value of the fuel. Based on the obtained results, it is possible to analyze and make recommendations for optimizing boilers in the gas refinery complex using response-surface method (RSM).

This work aimed at producing lactic acid (LA) from sugarcane bagasse after steam explosion at 195 ºC for 7.5 and 15 min. Enzymatic hydrolysis was carried out with Novozymes’ Cellic CTec3 and/or Cellic HTec3, whereas fermentation was performed with Bacillus coagulans DSM2314. Water-washing of pretreated solids before enzymatic hydrolysis improved both hydrolysis and fermentation yields. The presence of xylo-oligosaccharides (XOS) in substrate hydrolysates reduced hydrolysis efficiency, but their effect on fermentation was negligible. The presence of fermentation inhibitors in C5 streams was circumvented by adsorption on activated carbon powder with no detectable sugar losses. High carbohydrates-to-LA conversions (Yp/s) of 0.88 g·g-1 were obtained from enzymatic hydrolysates of water-washed steam-exploded materials that were produced at 195°C, 7.5 min and the use of centrifuged-but-never-washed pretreated solids decreased Yp/s by 16%. However, when the detoxified C5 stream was added at a 10% ratio, Yp/s was raised to 0.93 g·g-1 for an LA productivity of 2.55 g·L-1·h-1. Doubling the pretreatment time caused a decrease in Yp/s to 0.78 g·g-1, but LA productivity was the highest (3.20 g·L-1·h-1). For pretreatment at 195°C for 7.5 min, elimination of water washing seemed feasible, but the use of longer pretreatment times made it mandatory to eliminate fermentation inhibitors.

This paper presents a new engagement model for climate change education (CCE) as a result of analysing interactive digital narratives (IDNs) created during the You and CO2 Climate Change Education Programme. Young people aged 13-15 from two schools in Wales participated in three workshops, which culminated in students producing IDNs about climate change using Twine storytelling software. An inductive, grounded-theory approach informed by Bourdieusien principles of habitus and value was used to explore students’ responses to the Programme. Stage 1 coding identified ‘Core Themes’ and located student responses along tri-axial continua showing engagement, agency, and power. Stage 2 coding combined ‘Core Themes’ to build upon Cantell’s 2019 Bicycle Model of Climate Change Education to create a new ‘Holistic Engagement Model for Climate Change Education and Action’ (HEMCCEA), where learners’ journeys towards full engagement with and understanding of CCE and action could be traced. Barriers to students’ engagement with and understanding of CCE were identified through Bourdieusien analysis of responses. Results show that engagement was related to children’s views on their capacity to effect change on individual, local and governmental level. The HEMCCEA provides a model for adjusting CCE curricula to accommodate young people’s varying cultures and views.

The use of biodiesel fuels in compression ignition engines leads to decrease CO, PM, HC and smoke opacity. However, NOx emissions increase importantly. Various methods to reduce NOx are used namely the EGR, the water injection method and the steam injection method. In this study, the steam injection method has been used instead of the other methods because of its benefits. This study examines the effects of steam injection on combustion products of diesel and biodiesel fuels by considering chemical equilibrium in order to determine the equilibrium combustion products involving 10 combustion products. A developed simulation code determing the equilibrium mole fractions and thermodynamic properties of combustion products is used for diesel and biodiesel fuels. It can be used for any fuel consisting of carbon, hydrogen or any oxygenated fuel. The results show that the mole fraction of CO2 and CO decrease with the steam injection ratios. NO mole fractions decrease with steam injection for lean mixtures but they increase slightly in the case of rich mixtures. The specific heat of combustion products increase with the steam injection ratios. Thus, the engine performance can be improved using the method. The model has been validated by comparing model results with the ones of NASA CEA software and GASEQ software using the methane as fuel. The relative errors of equilibrium mole fractions and thermodynamic properties of combustion products are less than 0.98 %.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.

Lignocellulosic biomass is a powerful approach for the production of sustainable biofuels and the further achievement of the goal of biomass conversion into a second-generation clean energy that can cope with the depletion of fossil reserves and rising energy requirements. In the conversion process, a pretreatment is essential to overcome the recalcitrance of the lignocellulosic biomass, accelerate its disintegration into cellulose, hemicellulose, and lignin and, in turn, get an optimal yield of fermentable sugars in the enzymatic hydrolysis. In addition to this, it should be industrially scalable and capable of enhancing fuel properties and feedstock processability. Here, steam explosion technology has stood out due to its results and advantages such as wide applicability, high efficiency in the short term, or lack of contamination in spite of its conventionality. This gentle and fast pretreatment incorporates high temperature autohydrolysis and structural alteration by explosive decompression. Steam explosion method has been one of the most effective especially for the hydrolysis of cellulose from agricultural wastes due to the lower quantity of acetyl groups in the composition of hemicellulose. In this aspect, sugarcane bagasse is a promising feedstock for bioethanol production due to its high cellulosic content and elevated availability. The objective of this review has been to compile the latest information on steam explosion pretreatment, stages, equipment, variables involved, by-products generated, as well as the advantages and disadvantages of the technique. At the same time, its feasibility and viability using sugarcane bagasse as feedstock has been discussed. Finally, the effectiveness of the technique with different feedstocks has been evaluated.

In the present work we present a methodology for teaching the basis of the genetic code through music composition, with the aim to combine science and arts learning. The project was carried out by 155 students, the so-called MARGA Consortium, with ages comprised between 10 and 17 years from different public schools located in the Principality of Asturias, Spain. The different groups generated 8 different music works using a short genetic sequence obtained from the human notch1 gene, receptor of mutations leading to chronic lymphocytic leukemia.

In the process of sustainable development in the future, human society faces problems such as severe population load, economic transition, and lack of educational measures. One of the root causes of these problems is the shortage of innovative talents. Therefore, how to cultivate learners with multi-disciplinary integration and innovation ability is the key point that should be paid attention to in promoting the concept of quality education and coping with the future sustainable development process. This paper uses questionnaire survey method and literature analysis method to analyze the development of many educational institutions with STEAM concept as the core in China since 2017. It is found that the existing STEAM educational institutions generally have the following problems: the lack of team composition、difficulty in independent research and development、single course content and insufficient validation of course effectiveness. In order to more effectively promote the sustainable development of China's future course, STEAM education institutions should focus on strengthening the following development strategy: gradient team building, continuous independent research and development, cutting-edge projects curriculum transformation mechanism and multi-angle course effectiveness verification.

Process simulation represents an important tool for plant design and optimisation, either applied to well established or to newly developed processes. Suitable thermodynamic packages should be selected in order to properly describe the behaviour of reactors and unit operations and to precisely define phase equilibria. Moreover, a detailed and representative kinetic scheme should be available to predict correctly the dependence of the process on its main variables. This review points out some models and methods for kinetic analysis specifically applied to the simulation of catalytic processes, as a basis for process design and optimisation. Attention is paid also to microkinetic modelling and to the methods based on first principles, to elucidate mechanisms and calculate thermodynamic and kinetic parameters. Different case histories support the discussion. At first, we have selected two basic examples from the industrial chemistry practice, e.g. ammonia and methanol synthesis, which may be described through a relatively simple reaction pathway. Then, a more complex reaction network is deeply discussed to define the conversion of bioethanol into syngas/hydrogen or into building blocks, such as ethylene.

CuO/ZnO/Al2O3 catalyst is a commonly used catalyst for rea methanol steam reforming reaction. Oxalic acid was as precipitant in preparing oxalate precursor of CuO/ZnO/Al2O3 catalyst by co-precipitation, deionized water and ethanol were as solvents, microwave irradiation and water bath were as aging heating manner respectively. It indicated that ethanol selected crystal phase composition of oxalate precursors and restricted their growth. Microwave irradiation prompted the isomorphous substitution between Cu2+ of CuC2O4 and Zn2+ of ZnC2O4 in mother liquid, forming the master phase (Cu,Zn)C2O4 in precursor, the solid solution Cu-O-Zn formed after calcination, which exhibited nano-fibriform morphology. It possessed small CuO grains, large surface area and strong synergy between CuO and ZnO, which is beneficial to improve the catalytic performance of methanol steam reforming, the STY of H2 reached 516.7 mL·g-1·h-1, and the selectivity of CO was only 0.29%.

CONTEXT– Energy is widely involved in human activity and corresponding emissions of SOX, NOX and CO2 from energy generation processes affect global climate change. Clean fuels are desired by society because of their reduced greenhouse gas emissions. Hydrogen is once such candidate fuel. Much hydrogen is produced from fossil fuel, with biomass being an alternative process. OBJECTIVE– The project compared the environmental impact of hydrogen production by natural gas steam reforming vs. biomass gasification. METHOD–Environmental impact was calculated from the input and output data from life cycle inventory analysis. The impact assessment was focused on greenhouse gas emission, acidification, and eutrophication. Models of the two processes were developed and analysed in OpenLCA. The agribalyse database was used to connect inventory flow data to environmental impacts. FINDINGS– For all three metrics, biomass gasification had lower impacts than natural gas steam reforming, sometimes by large margins. For biomass gasification the silica sand production contributes most to all three impact categories, whereas for natural gas steam reforming it is the LPG extraction.

Direct electric curing (EC) is a new green curing method for cement-based materials that improves the early mechanical properties via the uniform high temperature produced by Joule heating. To understand the effects of EC and steam curing (SC) on the mechanical properties and microstructure of cement-based materials, the mortar was cured at different temperature-controlled curing regimes (40°C, 60°C and 80°C). Meanwhile, mechanical properties, hydrate phase and pore structure of specimens were investigated. The energy consumption of two curing methods was compared and analyzed. The results show that the EC specimens have better and more stable growth of mechanical strength. The pore structure of EC specimen is also better than that of SC specimen at different maintenance ages. However, the hydration degree and products of samples cured by EC are similar to that SC samples. The energy consumption of EC is lower than SC. This study provides an important technical support for the EC in the production of energy-saving and high early-strength concrete precast components.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

To increase the efficiency of fuel processor and HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) combined system, it is essential to improve the efficiency of a fuel processor. In this research, the fuel processor was simulated by Aspen Hysys® simulator, and effect of the various operating conditions on the total efficiency was investigated. Thermal efficiency of the fuel processor increased as the temperature and S/C (Steam to carbon) ratio increased, and the efficiency was higher at the S/C ratio of 3 than at the S/C of 4 at the reformer temperature of 700 ℃ and higher. Under the selected operating conditions of the fuel processor, recycling of unreacted hydrogen from the anode off gas (AOG) of the HT-PEMFC improve the overall efficiency of the combined fuel processer and HT-PEMFC by a factor of 1.28. Operating conditions where the AOG supplied excessive heat than required for fuel processor operation were excluded. The high-efficiency operating conditions of the fuel cell system were proposed with the target of 5 kW of output as the capacity of the household HT-PEMFC.

The generation of eucalypt sawdust has increased in Uruguay with the expansion of pulp and paper industrial sites. Currently, most of this readily available feedstock is either not used or applied for producing heat and power by combustion in biomass boilers. In this work, eucalypt sawdust was subjected to steam explosion as the first step for cellulosic ethanol production within the biorefinery concept. The effect of sawdust moisture content, pretreatment temperature and residence time were evaluated, along with the influence of water washing of steam-exploded solids on enzymatic hydrolysis and fermentation yields. After steam explosion, 60% xylans and 97% acetyl groups were recovered mainly as oligomers and acetic acid in the pretreatment liquor. Eucalypt sawdust moisture content affected the enzymatic hydrolysis performance and glucan conversion efficiency. Water washing after pretreatment improved hydrolysis efficiencies and ethanol production yields by 10% with respect to the unwashed pretreated solids at the same experimental condition. The best ethanol yields were obtained using PSSF (pre-saccharification and simultaneous saccharification and fermentation) after pretreatment at 205°C for 10 min, using sawdust with an 8% moisture content. In this case, 227 L ethanol and 40 kg total xylose (including xylo-oligomers) were obtained per ton of dry eucalypt sawdust.

Gas turbine power plants have important roles in the global power generation market. The examines thermodynamically the impact of steam injection for a combined cycle including a gas turbine cycle with a two-stage turbine and carbon dioxide recompression. The combined cycle is compared with the simple case without steam injection. Steam injection’s impact is observed on important parameters such as energy efficiency, exergy efficiency, and output power. It is revealed that steam injection reduces exergy destruction in components compared to the simple case. The efficiencies for both cases are obtained. The energy and exergy efficiencies respectively are found to be 30.4% and 29.4% for the simple case, and 35.3% and 34.1% for the case with steam injection. Also, incorporating steam injection reduces emissions of carbon dioxide.

Steam Generator Level Control System (SGLCS) is one of the key instrumentations and control subsystems to ensure the safe operation of nuclear power plants. It is highly recommended to perform reliability analysis for SGLCS for making better maintenance strategy. SGLCS is a digital control system with complex redundant configuration and failure\self-diagnosis\repair action, traditional fault tree is not applicable due to its static property, Markov model is not a good choice too because of heavy burden of creating state transition graph for even medium-size system. Boolean Logic Driven Markov Process (BDMP) can describe complex failure-repair state transition via ‘trigger link’ and three kinds of leaf nodes, as well as keep compact and easy-read struct like fault tree. So BDMP is adopted to analysis reliability of SGLCS. Graphical BDMP modeling environment KB3 and Monte Carlo simulator YAMS is used for BDMP modeling and quantitative analysis respectively, and unavailability of SGLCS is obtained. The contribution of three parts of SGLCS to the unavailability of the system is also evaluated, and it is found that the water supply flow control part contributes the most to the failure of SGLCS.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

This study, which was supported by a quantitative research paradigm with two experiment and two control groups of 4x4 quasi-experimental design, aimed to find out the impact of a sustainable progressive STEAM (SP-STEAM Model) application model on 5th grade primary school students critical thinking dispositions and mathematic achievements in Northern Cyprus. The treatment model was applied to experimental groups for 14 weeks of time. Split-plot multiple group analysis of variance (Split-plot ANOVA) statistical technique was used to calculate between and within group significances regarding exogenous variable. SPSS24 software package was used for the analysis. Pre-test and post-test results derived from experiment and control groups revealed significant effect of SP-STEAM Model on 5th grade primary school students’ critical thinking dispositions as measured with CCTDI and mathematic achievements as measured with a dedicated ex-am. The results were discussed in detail under the light of related literature and suggestions for further studies were proposed.

Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

The present study evaluates mold fungal resistance of newly developed loose-fill thermal insulation materials from wheat straw, corn stalk and water reed. Three different processing methods of raw materials was performed by mechanical crushing (Raw, ≤ 20 mm), thermal-mechanical pulping (TMP) using 4% NaOH and steam explosion pulping (SEP). An admixture of boric acid (8%) and tetraborate (7%) was applied to all processed substrates due to their anti-fungal properties. Additionally, the fourth sample group was prepared from SEPs of all raw species without boric acid and tetraborate (SEP*) as control. Samples from all treatments were separately inoculated by 5 different fungal species and incubated in darkness for 28 days at 28 ℃ and RH >90%. The highest resistance to the colonization of mold fungi was achieved by TMP and SEP processing coupled with addition of boric acid and tetraborate, where molds infest only around 35% to 40% of the inoculated sample area. The lowest mold fungi resistance was detected for Raw and SEP* samples, each ~75% that was affected by rich amount of accessible nutrients, suggesting that boric acid and tetraborate additives alone did not prevent mold fungal growth as effective as in combination with TMP and SEP treatments. Together, the achieved fungal colonization scores after combined fungicide and pulping treatments are acceptable for the application of various renewable materials in future thermal insulation product development.

Fly ash cement has rarely been used in Japan, mainly because its strength development is slower than ordinary Portland cement. In this research, the effect of the new fly ash cement with both high alite (C3S) cement and fly ash modified by electrostatic belt separation method on cracking resistance of precast concrete prepared by steam curing was studied. The mechanical and shrinkage properties of the proposed fly ash concrete were compared with those of concrete made using OPC cement without fly ash. In order to study the cracking tendency of precast concrete with the proposed fly ash cement, thermal stress analysis was conducted taking into consideration of the experimental data of concrete properties with the different concrete mix proportions. A standard precast concrete box culvert model was used in this 3D FEM analysis and the distribution of temperature and relative humidity in cross section and induced restraint stress during and after steam curing were discussed. Steam-cured concrete with fly ash and high alite cement developed higher compressive strength on the first day of age than concrete with OPC. The proposed fly ash concrete developed high cracking resistance in the early days. On the other hand, the results showed that the drying shrinkage at later ages was the main cause of cracking.

Interdisciplinary STEM and STEAM education give us an opportunity for creativity and educational innovation in a world scenario that needs training in which students can achieve all educational objectives and are prepared to achieve sustainable development. The rural environment with its land is a scenario that provides us with a range of educational resources for the development of STEM and STEAM projects in which students who are better trained and prepared for the needs of today's world are developed, as well as students who are more linked and sensitized to the environment, with the rural environment and its land, so important in our time.  In this article, we will collect examples from Latin America; STEM projects are being developed in which young people establish links with their environment, territory, and the local environment surrounding them. We must look carefully at projects and works in which students' ties with their land and environment are valued through the STEM and STEAM education necessary today. In this scenario, a comparison has been made between Latin American countries and Spain.

The paper examines design and operating data of current concentrated solar power (CSP) solar tower (ST) plants. The study includes CSP with or without boost by combustion of natural gas (NG), and with or without thermal energy storage (TES). The latest, actual specific costs per installed capacity are very high, 6085 $/kW for Ivanpah Solar Electric Generating System (ISEGS) with no TES, and 9227 $/kW for Crescent Dunes with TES. The actual production of electricity is very low and much less than the expected. The actual capacity factors are 22% for ISEGS, despite combustion of a significant amount of NG largely exceeding the planned values, and 13% for Crescent Dunes. The design values were 33% and 52%. The study then reviews the proposed technology updates to produce better ratio of solar field power to electric power, better capacity factor, better matching of production and demand, lower plant’s cost, improved reliability and increased life span of plant’s components. The key areas of progress are found in materials and manufacturing processes, design of solar field and receiver, receiver and power block fluids, power cycle parameters, optimal management of daily and seasonal operation of the plant, new TES concepts, integration of solar plant with thermal desalination, integration of solar plant with combined cycle gas turbine (CCGT) installations and finally, specialization and regionalization of the project specification.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.