Turbine generator operates with complex cooling system due to the challenge in controlling the peak temperature of the stator bar caused by ohm loss, which is unavoidable. Therefore, it is important to characterise and quantifies the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of typical cooling system, so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air is varied to consider its operation condition, so that there are (1) outward flow and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) is also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of Computational Fluid Dynamics analysis is also conducted to support the observation from the experiment. For the inward flow case, the results suggest that the average Nusselt number of the 2nd duct is about 30% higher than the 3rd duct. The trend is similar with the effect of cross flow. The CFD results are in good agreement with the experimental data.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

This paper proposes an analytical model of the double-stator spoke-type permanent-magnet vernier machine (DSSTVM) using the subdomain model (SDM), which can be used to calculate the mag-netic field distribution and corresponding electromagnetic parameters of the DSSTVM. The whole field domain is divided into several subdomains according to the magnetic characteristics of each region, within which Laplace's and Poisson's equations are solved accordingly in terms of magnetic vector potential (MVP). Then, the magnetic flux density distribution, back electromotive force (EMF), and electromagnetic torque of the DSSTVM can be obtained correspondingly. Ultimately, finite element analysis (FEA) is adopted to validate the proposed analytical model's effectiveness for quickly predicting the no-load and on-load performances of the DSSTVM.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

This paper proposes a new structure of the dual-rotor hybrid-excited axial-flux permanent magnet vernier machine (DR-HEAFPMVM) with the modular stator and the consequent-pole PM (CPM) rotor for low-speed, high torque density applications such as in-wheel electric vehicles. The tooth-wound non-overlapping armature windings and direct current (DC) excitation windings are respectively arranged in stator main-teeth and split-teeth to obtain the modulated and adjustable air-gap flux densities, which result in the high torque density and outstanding flux-weakening capability. First, the design consideration, operation principle, and the air-gap flux density distributions of the proposed machine are elaborated based on the air-gap permeance function. Then, the influence of the pole ratios (PRs) and the DC excitation currents on the main electromagnetic performances of the DR-HEAFPMVM, such as the flux-weakening capability, back-electromotive force (back-EMF), on-load electromagnetic torque, loss distribution, and efficiencies, is investigated using the 3-D finite-element method (FEM). Results verify the feasibility of the flux adjustment of the DC excitation windings equipped in the split-tooth, and the design with a pole ratio of 8/1 tends to have higher torque density, higher machine efficiency, and considerable flux-weakening capability compared with the other two PRs.

This article presents a harmonic analysis of the stator currents of a squirrel-cage in-15 duction motor fed by a voltage source inverter with PWM space vector control (SV-PWM). The 16 influence of PWM switching frequency and dead time (dead-band) of controlled transistors on 17 THD and electromagnetic torque ripple is shown. The aim is to determine the lowest switching 18 frequency of the transistors for which the drive will operate correctly. Characteristics were de-19 termined as functions in the form of THD ( ), where the least square approximation was 20 used for stator current measurements when the PWM switching frequency is changed. The ap-21 proximations were realized for simulation and experimental results. To clarify the results, the 22 operation of hardware PWM circuits in microcontrollers was analyzed.