Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

Detection of the region of interest (ROI) is a critical step in laryngeal image analysis for the delineation of glottis contour. The process can improve both computational efficiency and accuracy of the image segmentation task, which will facilitate subsequent analysis and characterization of the vocal fold vibration as it correlates with voice quality and pathology. This study aims to develop machine learning based approaches for automatic detection of ROI for glottis image sequences captured by high-speed video-endoscopy (HSV), a clinical laryngeal imaging modality. In particular, we first applied the supporting vector machine (SVM) method using histogram of oriented gradients (HOG) feature descriptor, and second, trained a convolutional neural network (CNN) model for this task. Comparisons are made for both approaches in terms of accuracy of recognition and computation time.

Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

An algorithm is presented for a micro-model of a mining dump truck movement, which allows determining the optimal speed and acceleration of a vehicle, considering the change of the road grade. The structure of the simulation macro-model of an excavator-and-dump truck complex has been developed. The procedure for integrating a micro-model of a dump truck movement into a simulation model is shown. As a result of a series of experiments with a macro-model, the influence of open pit roads grade on the performance and efficiency of excavator-and-dump truck complexes was established. The necessity of considering in simulation excavator-and-dump truck complexes the speed regulation of dump trucks depending on the change in road grade is shown.

Quite a number of new metered parking systems have been introduced in recent years by the local authorities of various spa towns in Poland in connection with home zone conversion projects. The traffic signs posted in these locations were limited to the beginning and end of the demarcated parking area. Traffic circle (TC) is an example of traffic calming measures (TCM) used in home zones to slow down the traffic (case study – home zone in a small spa village). This article presents the results of a study investigating the speed reductions obtained with a home zone and traffic circle used as traffic calming measures. The indispensable speed surveys were carried out in relation to this study in two periods: in summer when the streets are crowded with tourists and in September with little pedestrian traffic. Two research hypotheses were formulated as part of the speed data analysis to verify the slowing effect of traffic circle and the relevance of traffic circles design parameters and location, road function and the surrounding streetscape. For each hypothesis statistical analyses were carried out using two nonparametric tests: two-sample Kolmogorov–Smirnov test and median test. The third research hypothesis formulated in this study was related to sustainable development factors related to fuel consumption and traffic-related air pollution including carbon dioxide, carbon monoxide, nitrogen oxide and hydrocarbons. This hypothesis was verified by estimating the amount of air pollution in the home zone under analysis in three different situations (scenarios): in summer with the travel speed reduced by pedestrian traffic to ca. 8–10 km/h and in September with a small number of pedestrians and 20–25 km/h resulting speed between traffic circles, reduced at traffic circle, and in a theoretical 30 km/h zone with 25–30 km/h assumed speed between traffic circles, dropping at traffic circle. These analyses confirmed the appropriateness of traffic circle as a home zone traffic calming measure, as long as its design is based on a detailed analysis of the relevant factors, including location, road function and the surrounding streetscape.

This research delves into the impact of complex low-speed wake flow structures on the aerodynamic characteristics of objects downstream. It employs the proper orthogonal decomposition (POD) method and the domain precursor simulation method to compare traditional methods and validate this approach. The study generates several flow structures of parallel dual-cylinder wakes with different scales and spacing. The variations in the aerodynamic coefficient of three downstream objects at various times passing through wakes of varying scales are appropriately compared and analyzed. The study establishes that the wake with a cylinder spacing of G=1.5 has a more compact and concentrated modal structure than that with a cylinder spacing of G=0.35. Smaller objects are more responsive to the wake flow structure with a spacing of G=1.5, whereas larger objects respond more to the flow structure with a spacing of G=0.35. The achieved results also reveal that the aerodynamic force coefficients of objects passing through the wakefield at different times are closely related to the temporal characteristics of the wake flow structure with different scales.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

This study aims to focus on using the Volterra series and machine learning for forecasting random and chaotic wind speed regimes, since the calm weather is mostly noticed at the local site, making the dataset selection difficult. A novel method is proposed to predict Volterra kernels up to the third order, using a forward-back propagation neural network with 12-month measurements at Fujairah site (UAE). Both daily and monthly wind speed data sets are investigated for forecasting. The three dominant hourly and daily kernels are extracted for each day and each month. Predicted future Volterra kernels are estimated from past values using both statistical analysis and individual neuro networks for each of the Volterra kernel coefficients. Due to the random nature of wind speed at the local site, a two-layer with 4 neurons per layer neuro network is used to locate the most variable and intense speed during 8-hours in the day. Forecasted wind speed is determined with errors arising from different sources such as the utilization of only 3rd-order Volterra kernels and the difficulty of machine training of the employed shallow network. Nevertheless, this work depicts a useful algorithm to forecast chaotic and random wind speed regimes. Computational time is a trade of the complexity of Volterra mathematical analysis.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

Mixture of abramis brama (freshwater bream), carassius carassius (crucian carp), and sander lucioperca (pike perch) scales was used for the preparation of fish scale powder containing about 26.5 wt. % of removed when heating components preferably of organic nature, and 63.5 wt. % of mineral components. Fish scale powder enriched with inorganic components was prepared from washed, dried, and ground fish scale mixture using vibration sieving. Inorganic powders consisting of hydroxyapatite and magnesium whitlockite were obtained via heat treatment of this fish scale powder at 800-1000 oC. Particles of these inorganic powders consisted of sintered grains with dimensions less than 100 nm after heat treatment at 800 oC, less than 200 nm after heat treatment at 900 oC, and 100-500 nm after heat treatment at 1000 oC. Fish scale powder enriched with inorganic components as well as heat-treated inorganic powders consisting of hydroxyapatite and magnesium whitlockite can be recommended for the production of different materials such as ceramics or composites.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

Growth benefits of high speed rail (HSR) for enterprises are not automatic, but require a buoyant local economy and a robust strategy. Against above background, main objectives of ex-ante case study have been to investigate local socio-economic and spatial impacts of proposed HSR project around Ahmedabad station area on Mumbai-Ahmedabad HSR corridor, analyze the opportunities and challenges of HSR development and draw policy implications. Qualitative research methodology has been used to elicit the perceptions and perspectives of randomly selected 43 small, medium and large enterprises. Data has been analyzed using descriptive statistics. The study reveals that HSR induced greater human interaction will activate local economy, improve business efficiency and generate employment. Frequent travels on business trips can influence enterprises decision to settle near HSR station for easy access and likely to promote realty development. The proposed HSR project should be developed in synergy with urban dynamics of cities in transition and metropolitan service cities. Poor public transport connectivity is likely to be a major challenge in improving HSR accessibility and enhancing overall impacts of HSR, which can be improved by developing an integrated urban transport system, for which cooperation of all stakeholders and coherence with firms’ strategies is essential.

The accuracy of wind field simulation and prediction is one of the most significant parameters in the field of atmospheric science and wind energy. Limited by the observation data, there are few researches on wind energy development. A 3D Doppler wind lidar (DWL) providing the high-vertical-resolution wind data over the urban complex underlying surface in February 2018 was employed to evaluated the accuracy of vertical wind field simulation systematically for the first time. 11 PBL schemes of the Weather Research and Forecasting Model (WRF) were employed in simulation. The model results were evaluated in groups separated by weather (sunny days, haze days and windy days), observation height layers, and various observation wind speeds. The test results presented that the vertical layer altitude of the observation point position was the most important factor. The simulation is fairly well at a height of 1000-2000m, as most of the relative mean bias of wind speed and wind direction are less than 20% and 6% respectively. Below 1000 m, the wind speed and direction biases are about 30%-150% m.s-1 and 6%-30% respectively. Moreover, when the observed wind speed was lower than 5 m.s-1, the bias were usually large, and the wind speed relative mean bias is up to 50-300%. In addition, the accuracy of simulated wind profile is better in 10-15m.s-1 than other speed ranges, and is better up 1000m than below 1000m in the boundary layer. We see that the WRF boundary layer schemes have different applicability to different weather conditions. The WRF boundary layer schemes have significant differences in wind field simulation with larger error under the complex topography. A PBL scheme is not likely to maintain its advantages in the long term under different conditions including altitude and weather conditions.

Artificial Intelligence is dominated by Artificial Neural Networks (ANNs). Currently, the Batch Gradient Descent (BGD) is the only solution to train ANN weights when dealing with large datasets. In this article, a modification to the BGD is proposed which significantly reduces the training time and improves the convergence. The modification, called Instance Eliminating Back Propagation (IEBP), eliminates correctly-predicted-instances from the Back Propagation. The speedup is due to the elimination of unnecessary matrix multiplication operations from the Back Propagation. The proposed modification does not add any training hyperparameter to the existing ones and reduces the memory consumption during the training.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Spaceborne altimeters are an important data source for obtaining global sea surface wind speeds (U10). Although many altimeter U10 algorithms have been proposed and they perform well, there is still room for improvement. In this study, the data from ten altimeters were collocated with buoys to investigate the error of the altimeter U10 retrievals. The U10 residuals were found to be significantly dependent on many oceanic and atmospheric parameters. Because these oceanic and atmospheric parameters are inter-correlated, an asymptotic strategy was used to isolate the impact of different parameters and establish a neural-network-based correction model of altimeter U10. The results indicated that significant wave heights and mean wave periods are effective in correcting U10 retrievals, probably due to the tilting modulation of long-waves on the sea surface. After the wave correction, the root-mean-square error of the retrieved U10 was reduced from 1.42 m/s to 1.24 m/s and the impacts of thermodynamic parameters, such as sea surface (air) temperate, became negligible. The U10 residuals after correction showed that the atmospheric instability can lead to errors on extrapolated buoy U10. The buoy measurements with large air-sea temperature differences need to be excluded in the Cal/Val of remotely sensed U10.

The underground complicated testing environment and the fan operation instability cause large random errors and outliers of the wind speed signals. The outliers and large random errors result in distortion of mine wind speed monitoring, which possesses safety hazards in mine ventilation system. Application of Kalman filter in velocity monitoring can improve the accuracy of velocity measurement and eliminate the outliers. Adaptive Kalman Filter was built by automatically adjusting process noise covariance and measurement noise covariance depending on the differences between measured and expected speed signals. We analyzed the fluctuation of airflow flow using data of wind speed flow and distribution characteristics of the tunnel obtained by the Laser Doppler Velocimetry system (LDV) studies. A state-space model was built based on the tunnel airflow fluctuations and wind speed signal distribution. The adaptive Kalman Filter was calculated according to the actual measurement data and the Expectation Maximization (EM) algorithm. The adaptive Kalman filter was used to shield fluid pulsation while preserving system-induced fluctuations. Using the Kalman filter to treat offline wind speed signal acquired by LDV, the reliability of Kalman filter wind speed state model and the characteristics of adaptive Kalman Filter were investigated. Results showed that the adaptive Kalman filter effectively eliminated the outliers and reduced the root-mean-squares error (RMSE), and the adaptive Kalman filter had better performance than the traditional Kalman filter in eliminating outliers and reducing RMSE. Field experiments in online wind speed monitoring were conducted using the optimized adaptive Kalman Filter. Results showed that adaptive Kalman filter treatment could monitor the wind speed with smaller RMSE compared with LVD monitor. The study data demonstrated that the adaptive Kalman filter is reliable and suitable for online signal processing of mine wind speed monitor.

In this paper, by evaluating extreme value of the qth-power current, a torque sharing function (TSF) family for reducing the torque ripples in the switched reluctance motor (SRM) is proposed. The optimization criteria of the TSF has two secondary objectives, including the maximization of the torque-speed range and the minimization of copper loss. The evaluation indices in terms of the peak phase current, the rms phase current, and the torque ripple factor are compared between the proposed TSF family and four conventional TSFs including linear, sinusoidal, exponential, and cubic TSFs. An optimization objective function that combines the maximum absolute value of the rate-of-change of the flux linkage (MAV-RCFL) and the qth-power of current is proposed and a weighting factor is used to balance the influence of the two optimization objectives. An optimal TSF can be easily obtained by solving the optimization problem from the TSF family. The proposed TSF is validated by using simulations and experiments with a three-phase 6/4 SRM with 7.5 kW, 3000 rpm, and 270 V DC-link voltage. The dynamic simulation model is implemented in Matlab/Simulink. The results demonstrate the validity and superiority of the proposed control method; the optimal TSF provides better torque-speed performance, and a better reduction in copper loss and torque ripples at high speed compared to the conventional TSFs obviously.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

With reference to Planck scale Hubble parameter, super luminal expansion speeds, super luminal rotation speeds, Mach’s principle and Holographic principle, we review the current cosmological observations with eight simple assumptions. By understanding Yuri N. Obukhov and V.A. Korotky proposed cosmic rotational effects of polarization of radiation due to massive bodies, to some extent cosmic rotation can be deep-rooted in an observational approach and the ratio of current angular velocity and Hubble parameter can be estimated. It is possible to show that, at H₀ =70 km/sec/Mpc, current cosmic temperature, age, radius, mass, mass density are 2.721 K, 4.41x10¹⁷ sec, 90 billion light years, 1.14654x10⁵⁴ kg, 0.0482 times the current critical density respectively. Clearly speaking, current universe seems to constitute 267 Hubble spheres. Important point to be noted is that, current rotational kinetic energy is 0.6667 times the current critical energy. Based on the estimated current mass density and current rotational kinetic energy, current cosmic dark matter density can be shown to be 0.2851 times the current critical density. These numerical coincidences cast serious doubt on the on the real existence of currently believed ‘dark energy’. Initial and current expansion speeds are 3x10⁸ m/sec and 3.56x10⁹ m/sec respectively. With increasing cosmic age and increasing cosmic expansion speed, current universe is expanding with a speed of 11.885c. By knowing the time to time future cosmic temperatures, future Hubble parameters and corresponding future cosmic expansion speeds can be estimated and thus future expansion speed can be understood. Starting from ‘speed of light’, our model assumes a continuous increase in expansion speed and attains a current radius of 90 billion light years (without inflationary concepts) and casts a serious doubt on the actuality of currently believed ‘inflation’.

The need for industrial and commercial machinery to maintain high torque while accurately following a variable angular speed is increasing. To meet this demand, induction motors (IMs) are commonly used with variable speed drives (VSDs) that employ a field-oriented control (FOC) scheme. Over the last thirty years, IMs have been replacing independent connection direct current motors due to their cost-effectiveness, reduced maintenance needs, and increased efficiency. However, IMs and VSDs exhibit nonlinear behavior, uncertainties, and disturbances. This paper proposes a robust combined adaptive passivity-based control (CAPBC) for this class of nonlinear systems that applies to angular rotor speed and stator current regulation inside an FOC scheme for IMs´ VSDs. It uses general Lyapunov-based design energy functions and adaptive laws with σ-modification to assure robustness after combining control and monitoring variables. Lyapunov’s second method and Barbalat Lemma prove that the control and identification error tends to be zero over time. Moreover, comparative experimental results with standard Proportional Integer controller (PIC) and direct APBC, show the proposed CAPBC effectiveness and robustness under normal and changing conditions

Primary ciliary dyskinesia (PCD) is an inherited disorder that impairs motile cilia, essential for respiratory health, with a reported prevalence of 1 in 16,309 within Hispanic populations. Despite having the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in 70% of Puerto Rican patients, the characterization of the ciliary dysfunction remains unidentified due to the unavailability of advanced diagnostic modalities like High-Speed Video Microscopy Analysis (HSVA). Our study implemented HSVA for the first time on the island as a tool to better diagnose and characterize the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in Puerto Rican patients. By applying HSVA, we analyzed the ciliary beat frequency (CBF) and pattern (CBP) in native Puerto Rican patients with PCD. Our results showed decreased CBF and a rotational CBP linked to the RSPH4A founder mutation in Puerto Ricans, presenting a novel diagnostic marker that could be implemented as an axillary test into the PCD diagnosis algorithm in Puerto Rico. The integration of HSVA technology in Puerto Rico substantially enhances the framework for PCD evaluation and diagnosis, facilitating prompt detection and early intervention for improved disease management. This initiative, demonstrating the potential of HSVA as an adjunctive test within the PCD diagnostic algorithm, could serve as a blueprint for analogous developments throughout Latin America.

This paper focuses on the impact that urban traffic has on the environment. The study characterizes the global effect of GHG emissions, including the ecologic evaluation and the characterization, normalization, and evaluation factor. The work makes a detailed survey of the different modes of driving and their influence on engine performance as one of the principal causes of gas emissions during the combustion process. The article analyzes six types of vehicles equipped with different engine configurations: diesel and gasoline, GLP and GNC, hybrid electric, and plug-in hybrid electric. Simulation of the driving mode under various operational conditions for every type of engine results in energy consumption, thus, in GHG emissions, carbon dioxide and monoxide, nitrogen oxides, and Sulphur dioxide. The study concludes that a reduction in vehicle speed, thus in the engine revolutions, has positive effects on engine combustion and gasses emissions, which is reduced by 27.5%. The study also concludes that the limitation in driving mode, avoiding sharp and sudden acceleration, may reduce up to 45% of GHG emissions. The changes applied in the driving mode improve the air quality in the urban environment, reducing the content of GHG from 39% to 61%.

Under high-frequency operating conditions, the high-speed solenoid valve (HSV) experiences energy loss and heat generation, which significantly impact its operational lifetime. Reducing the energy loss of HSV without compromising its opening response characteristics poses a significant challenge. To address this issue, a finite element simulation model of HSV coupled with a current feedback model is constructed to investigate the synergistic effects of dynamic response and energy loss. Predictive models for the opening response time, HSV driving energy, and Joule energy using Back Propagation neural network (BPNN) are established. Furthermore, a multi-objective optimization study on the current driving strategy using Non-dominated Sorting Genetic Algorithm II (NSGA-II) is conducted. After optimization, although there was a 6.24% increase in the opening response time, both HSV drive energy and Joule energy were significantly reduced by 15.67% and 22.49%, respectively. The proposed multi-objective optimization method for HSV driving strategy holds great significance in improving its working durability.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

The connectivity level of last-generation vehicles is constantly on the rise. The combined use of Vehicle-To-Everything (V2X) connectivity and autonomous driving can provide remarkable benefits through the optimization of the route and speed trajectory. In this framework, this paper focuses on vehicle eco-driving optimization in a connected environment. The virtual test rig of a premium segment passenger car was used for generating the simulation scenarios. The benefits, in terms of energy and time savings, that the introduction of V2X communication, integrated with cloud computing, can have in a real-world scenario were assessed. The Reference Scenario is a pre-defined Real Driving Emissions (RDE) compliant route, while the simulation scenarios were generated by assuming two different penetration levels of V2X technologies. The associated energy minimization problem is formulated and solved by means of a global optimization algorithm, i.e., Dynamic Programming (DP). The optimization framework includes information coming from the surrounding environment, e.g., traffic lights state, speed limits, distance to travel, etc. The simulations show that introducing a smart infrastructure along with optimizing the vehicle speed in a real-world route can potentially reduce the required energy by 54% while shortening the travel time by 38%. Finally, a sensitivity analysis is performed on the bi-objective optimization cost function to find a set of Pareto optimal solutions, between energy and travel time minimization.

Triple X syndrome (TXS, also known as trisomy X or 47,XXX) has been associated with impaired overall neurocognitive functioning in children and relatively young adults. However, neurocognitive functioning in adults with TXS is poorly understood. The aim of this study was, therefore, to examine cognitive functioning in adults with TXS. Methods: In this cross-sectional study, data were collected from 34 adult women with TXS (mean age = 32.9; SD = 13.1) and 31 controls (mean age = 34.9; SD = 13.7). General intellectual functioning, semantic/verbal memory, visual/episodic memory, psychomotor speed, and attention and executive functioning were then compared between these two groups. Results: We found that general intellectual functioning was significantly lower in the TXS group compared to the control group. In addition, women with TXS had more attention problems and lower psychomotor speed, particularly motor processing speed. When the analyses were adjusted for IQ, the strength of these associations decreased. The women in the TXS group also scored significantly lower at free recall in the verbal memory test, but not in immediate or delayed recognition. Finally, visual/episodic memory and executive functioning did not differ significantly between groups. Conclusions: Our analysis revealed that women with TXS score lower in general intellectual functioning and have impairments in motor processing speed and attention compared to controls, but do not differ with respect to executive functioning. These results offer new insights for improving the support of adults with TXS both at school and in the workplace.

Mechanical power and motion are often transmitted by the gear-rotor-bearing system. When there are fitting clearances between the housing and outer ring in bearings, complex vibration responses will be generated, which makes the operating status difficult to identify. Therefore, for analyzing dynamic responses, a dynamic model of gear-rotor-bearing systems with bearing fitting clearances is proposed. In the model, the bearing system with fitting clearances and gear pair system are combined, and the coupling relationship is determined by the gyroscopic mo-tion of the shaft. The friction force and collision force caused by fitting clearances are also con-sidered, which are simulated by the Coulomb friction model and Hertz theory. The result shows that the meshing stiffness will also be excited by the bearing displacement. When there are fit-ting clearances on the bearing, the amplitude modulation of the bearing outer raceway to the system time-domain response is intensified, and the multiple harmonic frequency of bearings and gear pairs are generated on the spectrum, as well as defect frequencies of gear pairs. As the fitting clearance is increased, the higher multiple harmonic responses will be caused. Although the response amplitude of the gearbox is increased by raising the input speed, multiple harmon-ic responses are suppressed, which makes the system mainly vibrate at the fundamental fre-quency. Then, the dynamic model and the vibration analysis are experimentally verified.

Fractal behavior and long-range dependence are widely observed in measurements and characterization of traffic flow in high-speed computer networks of different technologies and coverage levels. This paper presents the results obtained when applying fractal analysis techniques on a time series obtained from traffic captures coming from an application server connected to the Internet through a high-speed link. The results obtained show that traffic flow in the dedicated high-speed network link have fractal behavior when the Hurst exponent is in the range of 0.5, 1, the fractal dimension between 1, 1.5, and the correlation coefficient between –0.5, 0. Based on these results, it is ideal to characterize both the singularities of the traffic and its impulsiveness during a fractal analysis of temporal scales. Finally, based on the results of the time series analyses, the fact that the traffic flows of current computer networks exhibit fractal behavior with a long-range dependency is reaffirmed.

In the present paper, an aerodynamic investigation of a high-speed train is performed. In the first section of this article, a generic high-speed train against a turbulent flow is simulated, numerically. The Reynolds-Averaged Navier-Stokes (RANS) equations combined with the SST turbulence model are applied to solve incompressible turbulent flow around a high-speed train. Flow structure, velocity and pressure contours and streamlines at some typical wind directions are the most important results of this simulation. The maximum and minimum values are specified and discussed. Also, the pressure coefficient for some critical points on the train surface is evaluated. In the following, the wind direction influence the aerodynamic key parameters as drag, lift, and side forces at the mentioned wind directions are analyzed and compared. Moreover, the effects of velocity changes (50, 60, 70, 80 and 90 m/s) are estimated and compared on the above flow and aerodynamic parameters. In the second section of the paper, various data-driven methods including Gene Expression Programming (GEP), Gaussian Process Regression (GPR), and random forest (RF), are applied for predicting output parameters. So, drag, lift and side forces and also minimum and a maximum of pressure coefficients for mentioned wind directions and velocity are predicted and compared using statistical parameters. Obtained results indicated that RF in all coefficients of wind direction and most coefficients of free stream velocity provided the most accurate predictions. As a conclusion, RF may be recommended for the prediction of aerodynamic coefficients.

Simulator training for image-guided surgical interventions may benefit from artificial intelligence systems that control the evolution of task skills in terms of time and precision of a trainee's performance on the basis of fully automatic feed-back systems. At the earliest stages of training, novice trainees frequently focus on getting faster at the task, and may thereby compromise the optimal evolution of the precision of their performance. For automatically guiding them towards attaining an optimal speed-accuracy trade-off, an effective control system for the reinforcement/correction of strategies must be able to exploit the right individual performance criteria in the right way, reliably detect individual performance trends at any given moment in time, and alert the trainee, as early as necessary, when to slow down and focus on precision, or when to focus on getting faster. This article addresses several aspects of this challenge for speed-accuracy controlled simulator training before any training on specific surgical tasks or clinical models should be envisaged. Analyses of individual learning curves from the simulator training sessions of novices and benchmark performance data of one expert surgeon, who had no specific training in the simulator task, validate the suggested approach.

In order to solve the problem of fault diagnosis for CNC machine feed system under the condition of variable speed conditions, an intelligent fault diagnosis method based on multi-domain feature extraction and ensemble learning model is proposed. First, various monitoring signals including vibration signal, noise signal and current signal are collected. Then, the monitoring signals are preprocessed and the time-domain, frequency-domain and time-frequency domain feature indexes are extracted to construct a multi-dimensional mixed domain feature set. Finally, the feature set is putting into the constructed DoubleEnsemble-LightGBM model to realize the fault diagnosis of the feed system. The experimental results show that the model can achieve good diagnosis results under different working conditions for both the public data set and the feed system test bench data set, and the average overall accuracy is 91.07% and 98.06% respectively. Compared with XGBoost and other advanced ensemble learning models, the method has better accuracy. It provides technical support for the stable operation and intelligent of CNC machine tools..

It has been known that dimensional constants such as ℏ, c, G, e, and k are merely human constructs whose values and units vary depending on the chosen system of measurement. Therefore, the time variation of dimensional constants lacks operational significance due to their dependence on them. It is well-structured and represents a valid discussion. However, this fact only becomes a meaningful debate within the context of a static or present universe. As well-established theoretically and observationally, the current universe is undergoing accelerated expansion, wherein dimensional quantities, like the wavelength of light, also experience redshift phenomena elongating over cosmic time. In other words, in an expanding universe, dimensional quantities of physical parameters vary with cosmic time. From this perspective, there exists the possibility that dimensional constants, such as the speed of light, could vary with the expansion of the universe. In this review paper, we contemplate under what circumstances the speed of light may change or remain constant over cosmic time, and discuss the potential for distinguishing these cases observationally.

EV transmissions operate at high speeds, upto 30,000 rpm. High speed operation puts higher demands on bearings, seals, and gears. Bearings in EV transmissions are prone to electrically induced bearing damage and may exhibit signs of pitting and fluting. Surface-initiated rolling contact fatigue is another common problem gaining increased attention lately. Most EV transmissions require a coupling between an oil-lubricated gearbox to an electrical motor that runs with minimal lubrication at very high rpm. High mechanical and thermal stresses the seals are exposed to under starved lubrication conditions have a detrimental impact on their service life. Hence, proper lubrication is critical. In general, EV transmission fluids call for a somewhat different spectrum of properties compared to conventional ATF. Gear tribology simulations open new ways to the design and optimization of lubrication for EV transmissions. Additionally, such simulations can also provide valuable insights into the effects of different oil properties on cooling and lubrication efficiencies, thereby helping in matching the lubricant and hardware characteristics for optimal performance. In the present communication, we demonstrate the effects of different lubricants and surface finishing technologies on the tribology of high-speed gears using tribological tests and advanced thermal elastohydrodynamic (TEHD) simulations. Important roles of lubricity additives and surface finish optimization are highlighted in conjunction with a move towards ultralow viscosity EV transmission fluids.

Applying the improved social network analysis method and the idea of rolling window regression, this paper explores the impact of HSR network on the quality of urbanization and its dynamics. Based on a sample of 273 cities in China over 2009–2019, we find that the high-speed railway network has an increasing positive effect on the quality of urbanization, which proves the existence of network effect. The empirical results further show that this effect is closely related to the cov-erage rate of high-speed rail network. In addition, heterogeneity analysis reveals that urban ag-glomeration cities are the main beneficiaries. Academically, our study provides a plausible expla-nation and evidence from network size differences for the two conflicting views of the HSR effect. Practically, we also propose some important policy implications for countries in different high-speed rail network construction stages.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

Aiming at the prediction of environmental vibrations induced by elevated high-speed railway, a machine-learning method is developed by combining random forest algorithm and Bayesian optimization, which using the dataset from on-site experiments . When it comes to achieving a rapid and effective prediction of environmental vibration, there is few research on com-parisons and verifications of different algorithms, and neither on parameter tuning and optimi-zation of machine learning algorithms. In this paper, a field experiment is firstly carried out to measure the ground vibrations caused by high-speed trains running on bridge, and then the en-vironmental vibration characteristics are analyzed in view of ground accelerations and weighted vibration levels. Subsequently, three machine-learning algorithms of linear regression, support vector machine and random forest are developed by using experimental database, and their prediction performance are discussed. Finally, two optimization models for the hyperparameter set of random forest algorithm are further compared. It turns out that the integrated random forest algorithm has higher accuracy in predicting environmental vibration than linear regression and support vector machine; the Bayesian optimization has excellent performance and high efficiency in achieving efficient and in-depth optimization of parameters, and can be combined with the RF machine learning algorithm to effectively predict the environmental vibrations induced by the high-speed railway.

In this work, we introduce a scalable and efficient GPU-accelerated methodology for volumetric particle advection and finite-time Lyapunov exponent (FTLE) calculation, focusing on the analysis of Lagrangian Coherent Structures (LCS) in large-scale Direct Numerical Simulation (DNS) datasets across incompressible, supersonic, and hypersonic flow regimes. LCS play a significant role in turbulent boundary layer analysis, and our proposed methodology offers valuable insights into their behavior in various flow conditions. Our novel owning-cell locator method enables efficient, constant-time cell search, and the algorithm draws inspiration from classical search algorithms and modern multi-level approaches in numerical linear algebra. The proposed method is implemented for both multi-core CPUs and Nvidia GPUs, demonstrating strong scaling up to 32,768 CPU cores and up to 62 Nvidia V100 GPUs. By decoupling particle advection from other problems, we achieve modularity and extensibility, resulting in consistent parallel efficiency across different architectures. Our methodology was applied to calculate and visualize the FTLE on four turbulent boundary layers at different Reynolds and Mach numbers, revealing that coherent structures grow more isotropic proportional to the Mach number, and their inclination angle varies along the streamwise direction. We also observed increased anisotropy and FTLE organization at lower Reynolds numbers, with structures retaining coherency along both spanwise and streamwise directions. Additionally, we demonstrated the impact of lower temporal frequency sampling by upscaling with an efficient linear upsampler, preserving general trends with only 10% of the required storage. In summary, we present a particle search scheme for particle advection workloads in the context of visualizing LCS via FTLE that exhibits strong scaling performance and efficiency at scale. Our proposed algorithm is applicable across various domains requiring efficient search algorithms in large structured domains. While this manuscript focuses on the methodology and its application to LCS, an in-depth study of the physics and compressibility effects in LCS candidates will be explored in a future publication.

The continuously developing project aims to build an informatics system enabling analysis of spatial and temporal parameters of movement activities occurring in the sport of speed climbing. The monitoring system (climbing information speed system – CISS) is to be used for conducting comprehensive scientific research in the field of speed climbing. The system enables the evaluation of the training process of climbers at various levels of competition. The study analysis was based on video. The video recording with a camera positioned at a short distance (10 m) from the wall. The marker was positioned closest to the centre of mass (gravity) BMC. Results: development of a system for data collection and analysis of the climbing run based on video recording (application of the Kanade-Lucas-Tomasi (KLT) algorithm). Our results showed that used devices can measure a wide range of specific internal and external variables during speed climbing. Some of the analyzed parameters were significantly correlated with speed climbing time. These results could be a theoretical basis for future research and for training program’s preparation.

In any region of a space, the gravitational field cannot be eliminated. The speed of light in a vacuum has never been observed and cannot be observed with current technology. Till now, only the speed of light in a gravitational field has been observed. It results in that all the observed speed of light are always being varied by the gravity. Here, it is presented that light could be dispersion in a gravitational field analogous to the dispersion of light in the Newtonian prism experiment. The relativistic mass density on the surface of a neutron star is on the level of 10¹⁷kg/m³ while on the surface of the Earth is only 10^-7kg/m³, the effect of the gravitational field acting on the speed of light by a neutron star is much larger than that by the Earth. Therefore, the dispersion of light in strong gravitational field could be generally observed from the image of a star and it should have been observed through the double-image gravitational lensing and the spectroscopic binary system. And, it should affect the observed numbers, spectrogram, size and distance of the celestial objects.

An extension of the models used to generate fractal traffic flows is presented by means of the formulation of a model that considers the use of one-dimensional chaotic maps. Based on the disaggregation of the temporal series generated by the model, a valid explanation of behavior of the values of Hurst exponent is proposed and the feasibility of their control from the parameters of the proposed model is shown.

Air change rate is an important parameter for quantification of ventilation heat losses and also affects the indoor climate of buildings. Indoor air quality is significantly associated with ventilation. If air change isn't sufficient, trapped allergens, pollutants and irritants can degrade the indoor air quality and affect the well-being of a building's occupants. Many studies on ventilation and health have concluded that lower air change rates can have a negative effect on people’s health and low ventilation may result in an increase in allergic diseases. Quantification of air change rate is complicated, since it is affected by a number of parameters, of which the one of the most variable is the air-wind flow. This study aims to determination and comparison of values of the air change rate in two methods - by quantifying of aerodynamic coefficient Cp = Cpe - Cpi – so called aerodynamic quantification of the building and the methodology based on experimental measurements of carbon dioxide in the selected reference room in apartment building.

In this paper, we present a high-speed, unified elliptic curve cryptography (ECC) processor for arbitrary Weierstrass curves over GF(p), which to the best of our knowledge, outperforms other similar works in terms of execution time. Our approach employs the combination of the schoolbook long and Karatsuba multiplication algorithm for the elliptic curve point multiplication (ECPM) to achieve better parallelization while retaining low complexity. In the hardware implementation, the substantial gain in speed is also contributed by our n-bit pipelined Montgomery Modular Multiplier (pMMM), which is constructed from our n-bit pipelined multiplier-accumulators that utilizes DSP primitives as digit multipliers. Additionally, we also introduce our unified, pipelined modular adder/subtractor (pMAS) for the underlying field arithmetic, and leverage a more efficient yet compact scheduling of the Montgomery ladder algorithm. The implementation on the 7-series FPGA: Virtex-7, Kintex-7, and XC7Z020, yields 0.139, 0.138, and 0.206 ms of execution time, respectively. Furthermore, since our pMMM module is generic for any curve in Weierstrass form, we support multi-curve parameters, resulting in a unified ECC architecture. Lastly, our method also works in constant time, making it suitable for applications requiring high speed and SCA-resistant characteristics.

In this paper we re-investigated the relationship between the symmetry of inertial systems and the Lorentz transformation. We found that when we just follow the following three principles: (1)we can define the time in the whole space with a prescribed clock synchronization, (2)the time-space is uniform and the space is isotropic and (3)all the inertial systems are equivalent, then we can totally construct a general coordinate transformation to meet the symmetry of inertial systems, and with a special assumption on the speed of light, we can construct a non-Lorentz transformation between inertial systems to make the particle’s energy have a limited value, which is similar to the rainbow model. Similar to the usual Lorentz violating models, the non-Lorentz transformation in this paper lead to a new modified disperse relation. We applied the obtained disperse relation to analyze the photon’s arrival time lag effect in astronomy and found that the "maximum energy" derived in our model is somewhat related to the "maximum energy" assumed in the rainbow model.

Conventional plant breeding methods exploit already existing genomic variation in plants to develop a variety in 8 to 10 years, which can decrease the genetic variability of the plant’s genome. The ever-increasing food demand for cereals crops cannot be met by traditional breeding methods. In order to increase food production in less time, there is a dire need to improve breeding methods. Several conventional and molecular breeding methods are being used to improve the crops traits. Molecular researchers have developed new genome editing tools like CRISPR/Cas9, CRISPR/Cpf1, prime editing, base editing, dcas9 epigenetic modification, and several other transgene-free genomes editing approaches. These genome editing tools can improve the desired traits precisely and efficiently. Moreover, a newly developed breeding method “Speed Breeding” has revolutionized the agriculture by shortening the crop cycle. It can produce 5-6 generations of cereals in a year. In this review, we have summarized all these conventional and molecular breeding approaches to improve cereal crops.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

The determination of crack propagation velocities can provide valuable information for a better understanding of damage processes of concrete. The spatio-temporal analysis of crack patterns developing at a speed of several hundred meters per second is a rather challenging task. In the paper, a photogrammetric procedure for the determination of crack propagation velocities in concrete specimens using high-speed camera image sequences is presented. A cascaded image sequence processing which starts with the computation of displacement vector fields for a dense pattern of points on the specimen’s surface between consecutive time steps of the image sequence chain has been developed. These surface points are triangulated into a mesh, and as representations of cracks, discontinuities in the displacement vector fields are found by a deformation analysis applied to all triangles of the mesh. Connected components of the deformed triangles are computed using region-growing techniques. Then, the crack tips are determined using principal component analysis. The tips are tracked in the image sequence and the velocities between the time stamps of the images are derived. A major advantage of this method as compared to established techniques is in the fact of its allowing for spatio-temporally resolved, full-field measurements rather than point-wise measurements and that information on crack width can be obtained simultaneously. To validate the experimentation, the authors processed image sequences of tests on four compact-tension specimens performed on a split-Hopkinson tension bar. The images were taken by a high-speed camera at a frame rate of 160,000 images per second. By applying to these datasets the image sequence processing procedure as developed, crack propagation velocities of about 800 m/s were determined with a precision in the order of 50 m/s.

The violation of data integrity in automotive Cyber-Physical Systems (CPS) may lead to dangerous situations for drivers and pedestrians in terms of safety. In particular, cyber-attacks on the sensor could easily degrade data accuracy and consistency over any other attack, we investigate attack detection and identification based on a deep learning technology on wheel speed sensors of automotive CPS. For faster recovery of a physical system with detection of the cyber-attacks, estimation of a specific value is conducted to substitute false data. To the best of our knowledge, there has not been a case of joining sensor attack detection and vehicle speed estimation in existing literatures. In this work, we design a novel method to combine attack detection and identification, vehicle speed estimation of wheel speed sensors to improve the safety of CPS even under the attacks. First, we define states of the sensors based on the cases of attacks that can occur in the sensors. Second, Recurrent Neural Network (RNN) is applied to detect and identify wheel speed sensor attacks. Third, in order to estimate the vehicle speeds accurately, we employ Weighted Average (WA), as one of the fusion algorithms, in order to assign a different weight to each sensor. Since environment uncertainty while driving has an impact on different characteristics of vehicles and cause performance degradation, the recovery mechanism needs the ability adaptive to changing environments. Therefore, we estimate the vehicle speeds after assigning a different weight to each sensor depending on driving situations classified by analyzing driving data. Experiments including training, validation, and test are carried out with actual measurements obtained while driving on the real road. In case of the fault detection and identification, classification accuracy is evaluated. Mean Squared Error (MSE) is calculated to verify that the speed is estimated accurately. The classification accuracy about test additive attack data is 99.4978%. MSE of our proposed speed estimation algorithm is 1.7786. It is about 0.2 lower than MSEs of other algorithms. We demonstrate that our system maintains data integrity well and is safe relatively in comparison with systems which apply other algorithms.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

This paper discusses how mathematical models are used to predict environmental conditions. While these models are successful for larger scale phenomena, it becomes more complex for local weather or wave processes. Several approaches have been proposed to address this problem, including neural networks and statistical and mathematical models. The novelty in this approach is the use of statistical manifolds, which provide a more accurate way to estimate distances and cost functions. This work focuses on advancements in differential and information geometry for creating different types of models that can be used for environmental simulation and forecasting. These fields are vital for many institutes and centres worldwide, as they help solve challenges in areas such as meteorology, renewable energy, and aviation safety. Some potential IG applications to advance energy were given. Closing remarks with new open problems combined with the next research phase are provided.

For both conventional and renewable energy conversion processes, computational fluid dynamics (CFD) has been used to address more energy-related challenges in recent decades. Using CFD to investigate vertical-axis wind turbines has become more common in recent years. The main goals of this application have been to more accurately predict the turbine's performance and to comprehend the complicated nature of the complex turbulent flow. The Vertical Axis Wind Turbine (VAWT) simulation for energy-generating applications has several intricate components. One of them is being aware of the chaotic flow that occurs during the first stages of the starting process, which influences overall effectiveness. In this article, the performance of the wind turbine was increased by using a passive flow control approach. The numerical research was carried out using Large Eddy Simulation for four alternative tip speed ratios in both cases, the classic and the optimized, equipped with a vortex trap on the exterior of the blades. The power and torque coefficient variations, as well as the velocity magnitude contours, show that the starting process may begin with a significant improvement in efficiency when flow control is used.

In order to reveal the frost heaving mechanism of void water behind the lining of high-speed railway tunnels in cold regions，the voids were first classified according to the positional relationship between voids and waterproof panels，and then the water supply and discharge conditions of different types of voids were investigated，then the influence of the excretion conditions on the frost heave force was experimentally studied. Based on these conditions，circular wedge-shaped and flying saucer-shaped void freezing models were established to analyze the evolution process of accumulated water frost heave. Then，according to the relative position of the excretion channel and the void，the excretion coefficient was introduced，and the calculation method of the frost heaving force of the voided water was proposed，and the influencing factors and laws of the frost-heave force were revealed. The results are shown as follows: 1) The blockage of the excretion channel will lead to the generation of frost heaving force; 2) The freezing and thawing process of the water within the cavity develops from the thinnest part of the void edge to the thicker part，and the process of frost heave-thaw，water replenishment-re-freeze heave of the water within the cavity leads to greater and greater frost heave force; 3) The frost-heaving force of the water within cavity is controlled by the void height and the position of the excretion channel. The larger the cavity height is or the closer the excretion channel is to the bottom surface of the void，the greater the frost-heave force is.

This study aims at better understanding the damage and fracture kinetics in flax fibres elements at both the unitary and bundle scales using an experimental setup allowing optical observation at high recording rate in the course of tensile loading. Defects issues from flax unitary fibre extraction are quantitated using polarized light microscopy. Tensile loading is conducted according to a particular setup adapted to fibres of 10 to 20 µm in diameter and 10 mm in length. Optical recording using high speed camera is performed during loading up to the failure at acquisition speed ranging from 108,000 to 270,000 frames per second. Crack initiation in polymer layers of fibre elements, propagation as well as damage mechanisms are captured. The results show different failure scenarios depending on the fibre element nature. In particular, fractured fibres underline either a fully transverse failure propagation or a combination of transverse and longitudinal cracking with different balances. Image recordings with high time resolution down to 3.7 μs suggest unstable system and transverse crack speed higher than 4 m/s and a slower propagation for longitudinal crack deviation.

In our recently published papers, considering Planck mass based light speed growing black hole universe and scaled Hawking’s black hole temperature formula, we have developed a simple procedure for estimating the current Hubble parameter and current cosmic mass. In addition to that, without considering galactic dark matter, starting from 10 km/sec to 500 km/sec, we have tried to fit the observed galactic flat rotation speeds with a concept of super gravity of galactic baryonic mass. To estimate the equivalent mass of currently hypothecated galactic dark matter, we have introduced a timely increasing cosmological reference mass unit. Its current magnitude seems to be around 200 million solar masses. In this paper, considering 200 million solar masses as a characteristic representation of cosmic weak interaction mass unit, we have developed a simple formula for its estimation. We would like to appeal that, weak interaction boosts the gravity of galaxies in proportion with their virtual dark mass as (galactic baryonic mass)^3/2 / (200 million solar masses)^1/2. With further study- dark matter existence and physical properties can be understood in a theoretical approach.

Improving the operational reliability of nuclear power plants, combined heat and power plants (CHP), as well as oil and gas pipelines is a priority task in the development of a variable-speed drive for lock valves used at these facilities. The paper analyzes technical requirements for such devices; the motor has been selected, its electrical equilibrium and moment equations have been obtained; recommendations for the selection of the kinematic drive scheme have been formulated. Based on the theoretical data obtained, a prototype has been developed, manufactured and tested.

The search algorithm based on symbiotic organisms’ interactions is a relatively recent bio-inspired algorithm of the swarm intelligence field for solving numerical optimization problems. It is meant to optimize applications based on the simulation of the symbiotic relationship among the distinct species in the ecosystem. The modified SOS algorithm is developed to solve independent task scheduling problems. This paper proposes a modified symbiotic organisms search based scheduling algorithm for efficient mapping of heterogeneous tasks to access cloud resources of different capacities. The significant contribution of this technique is the simplified representation of the algorithm's mutualism process, which uses equity as a measure of relationship characteristics or efficiency of species in the current ecosystem to move to the next generation. These relational characteristics are achieved by replacing the original mutual vector, which uses an arithmetic mean to measure the mutual characteristics with a geometric mean that enhances the survival advantage of two distinct species. The modified symbiotic organisms search algorithm (G_SOS) aimed to minimize the task execution time (Makespan), response, degree of imbalance and cost and improve the convergence speed for an optimal solution in an IaaS cloud. The performances of the proposed technique have been evaluated using a Cladism toolkit simulator, and the solutions are found to be better than the existing standard (SOS) technique and PSO.

In this review, we address issues that relate to the rapid “Warp Speed” development of vaccines to counter the COVID-19 pandemic. We review the antibody response that is triggered by SARS-CoV-2 infection of humans, and how it may inform vaccine research. The isolation and properties of neutralizing monoclonal antibodies from COVID-19 patients provide additional information on what vaccines should try to elicit. The nature and longevity of the antibody response to coronaviruses are relevant to the potency and duration of vaccine-induced immunity. We summarize the immunogenicity of leading vaccine candidates tested to date in animals and humans, and discuss the outcome and interpretation of virus-challenge experiments in animals. By far the most immunogenic vaccine candidates for antibody responses are recombinant proteins, which are not included in the initial wave of “Warp Speed” immunogens. A substantial concern for SARS-CoV-2 vaccines is adverse events, which we review by considering what was seen in studies of SARS-CoV-1 and MERS-CoV vaccines. We conclude by outlining the possible outcomes of the “Warp Speed” vaccine program, which range from the hoped-for rapid success to a catastrophic adverse influence on vaccine uptake generally.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

The three-dimensional single fin configuration finds application in an intake geometry where the cowl-shock wave interacts with the side-wall boundary-layer. Accurate numerical simulation of such three-dimensional shock/turbulent boundary-layer interaction flows, which are characterized by the appearance of strong crossflow separation, is a challenging task. Reynolds-averaged Navier-Stokes computations using the shock-unsteadiness modified Spalart-Allmaras model is carried out at Mach of 5 at large fin angle of 23^◦. The computed results using the modified model are compared to the standard Spalart-Allmaras model and validated against the experimental data. The focus of work is to implement the modified model and to study the flow physics in detail in the complex region of swept-shock-wave turbulent boundary-layer interaction in terms of the shock structure, expansion fan, shear layer and the surface streamlines. The flow structure is correlated to the wall pressure and skin friction in detail. It is observed that the standard model predicts an initial pressure location downstream of the experiments. The modified model reduces the eddy viscosity at the shock and predicts close to the experiments. Overall, the surface pressure using modified model is predicted accurately at all the locations. The skin friction is under predicted by both the models in the reattachment region and is attributed to the poor performance of turbulence models due to flow laminarization.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

The paper presents a new type of hydraulic clutch operating with magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. The hy-draulic clutch system of its own design with MR working fluid and a rotating magnetic field lo-cated is designed. The principle of this clutch is to use a rotating magnetic field created by an al-ternating current electromagnet to set the MR fluid in motion. In the tests of the hydraulic clutch with a rotating magnetic field, MR fluid produced on their own, consisting of solid iron particles of various diameters mixed with a silicone oil, are used as working fluids. The rheological properties of MR fluids are assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating the magnetic field of its own design. The char-acteristics of the hydraulic clutch with MR working fluid and the rotating magnetic field are tested on a specially built test stand. As a result of the research, it has been found that the torque transmitted by the clutch is the greater, the higher the rotational speed of the magnetic field and the lower the rotational speed of the beaker in which the working fluid is placed, and that the greatest torque occurs for the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch working with MR fluid and the rotating magnetic field can be applied to stationary power transmission system similarly to an eddy current clutch.

The star matter composed of nucleons deep inside the compact star like a neutron star is believed to be very dense and various new types of concepts and physical phenomena due to the nontrivial strong correlations are naturally expected. Peudo-conformality in dense star matter has been discussed recently assuming the hidden underlying scale symmetry, which is partly supported by the recent discussions of infrared conformal window of QCD. It is found that the appearance of dilaton and the dilatonic mean field calculation of nucleonic matter lead to the density independent nucleon mass at higher density regime than normal nuclear matter density. Non-vanishing constant nucleon mass can be considered as a chiral invariant mass of the parity doublet model, in which the chiral symmetry is manifested even in the massive nucleon sector provided with a parity doubling. In this paper we will discuss how the chiral and scale symmetry are correlated to lead the parity doublet symmetry inside the core of the compact star. A simple schematic model is adopted. The star matter at T=0 is basically composed of the nucleons. As a first approximation, they can be treated as free fermions with the effective mass filled up to fermi surface. There is a nontrivial feature due to the interplay between vector meson and nucleon(or equivalently dilaton, χ). The trace of energy momentum tensor approaches density independent, the pseudo-conformal phase. Local fluctuations inside the star matter will be travelling with the speed of sound which depends on the equation of state. In the pseudo-conformal phase, the speed of sound approaches to the conformal velocity for the scale symmetric matter, vc=13c. The excitations of the parity doublets in the compact star matter as an emerging phenomena in pseudo-conformal phase will be discussed in connection to the chiral symmetry. The possible implication on the corespondence of hadrons to quark degrees of freedom will be briefly discussed.

Speeding is a significant global issue, with disparities in speed outcome and speed research between low- and middle-income countries (LMICs) and high-income countries (HICs). This study aims to address speed research gaps by examining the prevalence of self-reported speeding and factors influencing drivers' speeding behavior (SB) using the Theory of Planned Behavior (TPB). An online survey involving 387 anonymous drivers was conducted in Yaoundé. Results showed that all drivers reported exceeding speed limits, with 81% exceeding by 5km/h, 12% by 10km/h, and 7% by more than 10km/h in urban areas. On highways, 54% reported exceeded the limit by more than 10km/h. Age, driver's license, and gender showed significant associations with speed limits non-compliance. The study results suggests that the TPB can be useful in assessing speeding behavior, as the inclusion of TPB variables led to a more than 50% proportionate increase in SB variance. Structural equation modeling revealed attitude towards speeding as the strongest predictor of speeding intention (SI), along with certain demographics indirectly influencing SB through SI. Perceived behavioral control (PBC) and SI directly influenced SB. These findings emphasize the potential of interventions targeting attitude, intentions, and perceived behavioral control to modify speeding behavior and improve road safety.

In the full load operating range, wind turbines typically use pitch control to maintain rotor speed and output power at their rated values to guarantee the whole system’s safety. Blade pitch actuators are subject to physical limitations and safety requirements, which imposes strict constraints on pitch angle’s amplitude and rate of change. These constraints will bring windup problem to the integral part of the pitch controller. It leads to deterioration of the pitch control system’s performance or even the instability problem, especially for large-scale turbines operating in extreme uncertain wind conditions or suffering from cyber attacks. This paper designs an anti-windup robust pitch angle control strategy to deal with pitch rate constraint issue to enhance the security of control system. First, to facilitate controller design, a filtered tracking error technique is employed to transform the nonaffine form into an affine one. Subsequently, a feedback robust controller based on UDE is developed to handle the model’s uncertainty and external disturbances. To address the issue of integral saturation in the pitch system and guarantee its safety, an elliptical bounded constraint is integrated into the designed UDE strategy. This bounded UDE controller can improve the stability of power generation quality, reduces the mechanical loads on components and enhance the whole system’s safety. Finally, the effectiveness of the proposed scheme is verified on the Wind Turbine Blockset platform in Matlab/Simulink. It can achieve better performance than the traditional method.

An approach based on the OpenFOAM library has been developed to solve a high-speed, multicomponent mixture of a reacting, compressible flow. This work presents comprehensive validation of the newly developed solver called compressibleCentralReactingFoam with different supersonic flows, including shocks, expansion waves, and turbulence-combustion interaction. The comparisons of the simulation results with experimental and computational data confirm the fidelity of this solver for problems involving multicomponent high-speed reactive flows. The gas dynamics of turbulence-chemistry interaction are modeled using a partially-stirred reactor formulation and provide promising results to better understand the complex physics involved in supersonic combustors. A time-scale analysis based on local Damköhler numbers reveals different regimes of turbulent combustion. In the core of the jet flow, the Damköhler number is relatively high indicating that the reaction time scale is smaller than the turbulent mixing time scale. This means that the combustion is controlled by turbulent mixing. In the shear layer, where the heat release rate and the scalar dissipation rate have the highest value, the flame is stabilized due to finite rate chemistry with small Damköhler numbers and a high fraction of fine structure. This solver allows three-dimensional gas dynamic simulation of high-speed multicomponent reactive flows relevant to practical combustion applications.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

Growing population, industrialization, and power requirements are adversely affecting the environment by increased greenhouse gases, resulting from fossil fuel burning. Global greenhouse gas mitigation targets have led the nations to promote clean and self-renewable sources of energy to address the environmental issue. Offshore wind power resources are relatively more attractive due to high winds, less turbulence, minimal visualization effects, and no interaction of infrastructure. The present study aims at conducting offshore wind power resources assessment (OWPRA) at some locations in the Gulf of North Suez. For this purpose, the long-term hourly mean wind speed (WS) and wind direction above means sea level (AMSL) and temperature and pressure data near surface is used. The data is obtained from ERA5 (fifth generation reanalysis for the global climate weather) at chosen six (L1-L6) offshore locations. The data covers a period of 43 years, between 1979 and 2021. The WS and direction are provided at 100 m AMSL while temperature and pressure are available near water surface level. At L1 to L6 locations, the log-term mean WS and wind power density (WPD) values are found to be 7.55 m/s and 370 W/m2, 6.37 m/s and 225 W/m2, 6.91 m/s and 281 W/m2, 5.48 m/s and 142 W/m2, 4.30 m/s and 77 W/m2, and 5.03 and 115 W/m2 and at 100 m AMSL; respectively. The higher magnitudes of monthly and annual windy site identifier indices (MWSI and AWSI) of 18.68 and 57.41 and 12.70 and 42.94 at L1 and L3 sites and generally lower values of wind variability indices are indicative of favourable winds source, which is also supported by higher magnitudes of mean WS, WPD, annual energy yields, plant capacity factors, and wind duration at these sites. The cost of energy, for the worst and the best cases are estimated as 10.120 USD/kWh and 1.274 USD/kWh at L5 and L1 sites corresponding to wind turbines WT1 and WT4. Based on the analysis, sites L1, L3, and L2 are recommended for wind farm development in order of preference. The wind variability and windy site identifiers indices introduced, will help decision-makers in deciding the potential windy sites with more confidence.

As one of the fastest-growing new energy sources, wind power technology has attracted widespread attention from all over the world. In order to improve the quality of wind power generation, wind speed prediction is an indispensable task. In this paper, an error correction based Variational Mode Decomposition and Broad Learning System (VMD-BLS) hybrid model is proposed for wind speed prediction. First, the wind speed is decomposed into multiple components by the VMD algorithm, and then an ARMA model is established for each component to find the optimal number of sequence divisions. Second, the BLS model is used to predict each component, and the prediction results are summed to obtain the wind speed forecast value. However, in some traditional methods, there is always time lag, which will reduce the forecast accuracy. To deal with this, a novel error correction technique is developed by utilizing BLS. Through verification experiment with actual data, it proves that the proposed method can reduce the phenomenon of prediction lag, and can achieve higher prediction accuracy than traditional approaches, which shows our method’s effectiveness in practice.

JBIR-99 is a secondary metabolite of marine fungi that has been shown to possess strong antibiotic activity. An efficient approach using a combination of size exclusion chromatography with a Sephadex LH-20 and high-speed counter-current chromatography (HSCCC) has been successfully developed for the isolation and purification of a polyketide from the solid-state fermentation of Meyerozyma guilliermondii. The active compound was isolated with purity >95% by HSCCC using an optimized solvent system composed of petroleum ether–ethyl acetate– 95% ethanol–water (5:3:5:3, v/v/v/v) after size exclusion chromatography. This compound was successfully purified in the quantity of 68 mg from 120 mg of the crude extract. The structure of JBIR-99 was elucidated and assigned by 1D, 2D NMR spectroscopic, and positive HRESITOFMS. Moreover, the relative configuration of compound JBIR-99, displaying a quite complex multi-ring structure, is determined by X-ray crystallography for the first time. The purification method developed for JBIR-99 will facilitate the further investigation and development of this antibiotic agent as a lead compound. Furthermore, it is suggested that the combination of size exclusion chromatography and HSCCC could be more widely applied for the isolation and purification of polyketides from marine fungi.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

Warming of the climate system is unequivocal, and many of the observed changes are unprecedented over five decades to millennia. Globally the atmosphere and ocean is increasingly getting warmer, the amount of ice on the earth is decreasing over the oceans, and the sea level has risen. According to Intergovernmental Panel on Climate Change, the total increasing temperature globally averaged combined land and surface between the average of the 1850-1900 period and the 2003 to 2012 period is 0.78 °C (0.72 to 0.85). But should we prepare for such the relatively small change? The importance is not the mean of the warming but the considerable likelihood of climate change that could trigger extreme natural hazards. The impact and the risk of climate change associated with railway infrastructure have not been fully addressed in the literature due to the difference in local environmental parameters. On the other hand, the current railway network in Malaysia, over the last decade, has been significantly affected by severe weather conditions such as rainfall, lightning, wind and very high temperatures. Our research findings point out the extremes that can lead to asset system failure, degraded operation and ultimately, delays to train services. During the period of flood, the embankment of the track can be swept away and bridge can be demolished, while during drought, the embankment of the track can suffer from soil desiccation and embankment deterioration, high temperature increases the risk of track buckling and high winds can result in vegetation or foreign object incursion on to the infrastructure as well as additional quasi-static burden exerted. This review is of significant importance for planning and design of the newly proposed high speed rail link between Malaysia and Singapore.

A novel technique suitable for propulsion of small unmanned aerial vehicles (UAV) is discussed in this paper. This approach utilizes the rotational energy of airborne gyro rotors and converts it into translational propulsion for the vehicle. The energy conversion is achieved by generating precisely directed centrifugal force pulses through short-duration rotor unbalances. The accurate control of the timing and magnitude of these unbalances is crucial for successful propulsion generation. Our first-order theory of controlled unbalance propulsion (CUP) predicts the potential for achieving high translational accelerations and vehicle velocities up to orbital levels. Power saving levitation of UAVs can be attained. In this paper, we provide traceable evidence that pulsed centrifugal propulsion is based on well-established laws of physics and can be realized using state-of-the-art technologies.

Cells receive external stimuli to incur structural and functional damages. On scanning acoustic microscopy (SAM), speed-of-sound (SOS), attenuation-of-sound (AOS), and thickness values are plotted on the screen to create cellular images, which are related to stiffness, viscosity, and cell size, respectively. The obtained digital data compared using statistical analysis. We aimed to investigate the effects of anticancer drugs, acidic fluids, and heat effects on the cells by using SAM. Anticancer drug cisplatin induced cancer cell apoptosis/necrosis and regeneration in culture, causing elevated SOS, reduced AOS, and thickness. During a more prolonged incubation, the SAM values fluctuated differently between the cisplatin-treated and untreated cells. The tannic and acetic acid and microwave stimuli induced SOS and AOS elevations. These stimuli altered the cell size, number, differentiation, viscosity, and stiffness, which corresponded well to the fluctuation of the SOS and AOS values after incubation. Different anticancer drugs interacted with cancer cells to induce the characteristic alterations of the SAM values. These structural and mechanical alterations induced in cells was difficult to observe on light microscopy. Cellular damages were statistically compared between different stimuli and time-lapse cellular changes were observed using a SAM analysis. SAM is a useful modality to evaluate cellular damage.

This cross-country four-year longitudinal study investigated the development of processing speed throughout primary school education. The analyses were conducted on data collected from 441 schoolchildren in Grades 1, 2, 3 and 4 (aged 6.42 to 11.85 years) in the Kyrgyzstan and Russia. Mixed effects growth modeling was applied to estimate average and individual growth trajectories for processing speed at two cross-country samples. Latent class growth modeling was conducted to identify different types of growth trajectories for processing speed and to compare the distribution of the types within the analyzed samples. According to the results, processing speed significantly increases across primary school years. The trajectory is characterized by nonlinear changes with more intensive growth between Grades 1 and 2, which later slows down until Grade 4. There were no significant cross-country differences in the initial score of processing speed or developmental changes in processing speed across primary school years. The development of processing speed is described by a model with three quadratic growth types but minimally differs. It is concluded that in both samples, the development of processing speed may be characterized by homogeneity, with the most intensive growth from Grade 1 to Grade 2 and subsequent linear improvement until Grade 4.

The theory of special relativity has reexamined and reconstructed the concepts of space and time, which are indispensable for describing physical laws, consequently instigating a major revolution in physics in general. Although the correctness of the special theory of relativity has been con-firmed by many observations and experiments, it is unclear why the "principle of relativity" and the "principle of the constant speed of light," which form the basis of the idea, are valid. Moreo-ver, although special relativity has advanced our understanding of time, our understanding of the fundamental question, "What is time?" is still limited. The theory of special relativity regards space as a four-dimensional construct consisting of one-dimensional time and three-dimensional space. This paper proposes an alternative framework, wherein real space is uniform and isotropic four-dimensional space, and elementary particles are waves that propagate through this four-dimensional space at a constant speed. This new perspective provides evidence to support two of Einstein’s key principles—the "principle of relativity" and the "principle of the constant speed of light." Furthermore, this model clarifies what time is and why time flows at a constant rate from the past to the future.

Plant geneticists and breeders have used marker technology since the 1980s in quantitative trait locus (QTL) identification. Marker-assisted selection is effective for large-effect QTL but has been challenging to use with quantitative traits controlled by multiple minor effect alleles. Therefore, genomic selection (GS) was proposed to estimate all markers simultaneously, thereby capturing all their effects. However, breeding programs are still struggling to identify the best strategy to implement it into their programs. Traditional breeding programs need to be optimized to implement GS effectively. This review explores the optimization of breeding programs for variety release based on aspects of the breeder’s equation. Optimizations include reorganizing field designs, training populations, increasing the number of lines evaluated, and leveraging the large amount of genomic and phenotypic data collected across different growing seasons and environments to increase heritability estimates, selection intensity, and selection accuracy. Breeding programs can leverage their phenotypic and genotypic data to maximize genetic gain and selection accuracy through GS methods utilizing multi-trait and, multi-environment models, high-throughput phenotyping, and deep learning approaches. Overall, this review describes various methods that plant breeders can utilize to increase genetic gains and effectively implement GS in breeding .

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

Multiple preventive vaccines are being developed to counter the COVID-19 pandemic. The leading candidates have now been evaluated in non-human primates (NHPs) and human Phase 1 and/or Phase 2 clinical trials. Several vaccines have already advanced into Phase 3 efficacy trials, while others will do so before the end of 2020. Here, we summarize what is known of the antibody and T-cell immunogenicity of these vaccines in NHPs and humans. To the extent possible, we compare how the vaccines have performed, taking into account the use of different assays to assess immunogenicity and inconsistencies in how the resulting data are presented. We also summarize the outcome of SARS-CoV-2 challenge experiments in immunized macaques, while noting variations in the protocols used, including but not limited to the virus challenge doses.

The use of wind energy has been developing fast over the last years. The global cumulative wind power capacity increased by 10.5% in 2019, most of which comes from onshore wind farms. One of the consequences of this continuous increase is the use of land for onshore wind farms. There are already cases worldwide where lack of well-established plans and strategies have caused delays in projects. The need for efficiently using land for wind farms will be mandatory in the short term. In this work, we present a numerical analysis to evaluate wind farm land-use. By defining the ratio between mechanical output power over an area as a parameter called land-use ratio, this work focused on comparing several cases of aligned and staggered layouts. Mechanical output power was estimated using a validated code based on Blade Element Momentum code, and the wake velocities and wake interaction effects were estimated using a validated wind turbine CFD model. In terms of output power, staggered designs are more efficient than aligned designs. However, the results showed that even though staggered designs produced higher output power, aligned farms with tight lateral spacing could be as efficient as staggered ones in terms of land-use but using fewer turbines. In summary, tightly aligned designs should be a tendency in the future towards efficient use of land in wind farms.

The article presents formal proof that the Special Theory of Relativity is wrong, that is, the interpretation of the mathematics on which STR is based, proposed by Einstein is incorrect. The article shows that there are infinitely many kinematics in which one-way speed of light is always equal to c. The kinematics of Special Theory of Relativity (STR) is only one of those infinitely many kinematics. It presents that mathematics on which STR kinematics is based can be interpreted differently and this leads to other conclusions on the properties of this kinematics. In this article, the whole class of linear transformations of time and coordinate was derived. Transformations were derived on the assumption that conclusions from Michelson-Morley’s and Kennedy-Thorndikea’s experiments are met for the observer from each inertial frame of reference, i.e. that the mean velocity of light in the vacuum flowing along the way back and forth is constant. It was also assumed that there is at least one inertial frame of reference, in which the velocity of light in a vacuum in each direction has the same value c, and the space is isotropic for observers from this distinguished inertial frame of reference (universal frame of reference). Derived transformations allow for building many different kinematics according to Michelson-Morley’s and Kennedy-Thorndikea’s experiments. The class of transformations derived in the study is a generalization of transformations derived in the paper [10], which consists in enabling non-zero values of parameter e(v). The idea of such a generalization derives from the person, who gave me this extended transformations class for analysis and publication.

We report a novel dual-band barrier infrared detector (DBIRD) design using type-II superlattices (T2SLs). The DBIRD structure consists of back-to-back barrier diodes: a "blue channel" (BC) diode which has an nBp architecture, an n-type layer of larger bandgap for absorbing blue band infrared/barrier/p-type layer, and a "red channel" (RC) diode which has an pBn architecture, a p-type layer of smaller bandgap for absorbing red band infrared/barrier/n-type layer. Each has a unipolar barrier using a T2SL lattice matched to a GaSb substrate to impede the flow of majority carriers from the absorbing layer. Each channel in the DBIRD can be independently accessed with a low bias voltage, as is preferable for high-speed thermal imaging. Device modeling of DBIRDs and simulation results of the current-voltage characteristics under dark and illuminated conditions are also presented. They predict that dual-band operation of the DBIRD will produce low dark currents and 27-33% quantum efficiencies for the in-band photons in the BC with λc=5.58 μm, and a nearly-constant 33% in the RC with λc=8.05 μm. The spectral quantum efficiency of the BC for 500 K blackbody radiation is approximately 20% over the range of λ=3 − 4.2 μm, while that of the RC has a peak of 42% at 5.7 μm. The DBIRD may provide improved high-speed dual-band imaging in comparison with NBn dual-band detectors.

Based on four major cosmological and astrophysical coincidences, it seems possible to develop a new model of Hubble-Hawking Universe having light speed expansion. Considering the analysis of 740 super novae data, it is possible to consider a constant rate of cosmic expansion. As there is no physical reasoning for the observed speed of light and all the cosmological observations are completely based on speed of light-by considering ‘light speed expansion’ as a characteristic nature of the universe, big bang, inflation, dark energy, quintessence and lambda term like ideal and unidentified concepts can be reviewed and relinquished at fundamental level and a practical model of expanding universe can be developed with ease and clarity. In this context, we would like to emphasize the point that, traditional definition of cosmic red shift is absolutely wrong. In terms of energy of photon, true cosmic red shift must be defined as - ratio of loss of energy in photon to the energy of photon at galaxy. We encourage the reader to see Figure 1 and Table 1 pertaining to light travel distances prepared with $\left(\frac{z}{1+z}\right)\left(\frac{c}{H_0}\right)\cong z_{new}\left(\frac{c}{H_0}\right)$. For data comparison, readers are encouraged to visit https://cosmocalc.icrar.org/ and http://www.atlasoftheuniverse.com/cosmodis.c. It may be noted that, considering 200 million solar masses as a cut off for ordinary gravity, dark matter can be considered as an effect of power law based super gravity of galactic baryonic mass. It is well believed that, Hawking’s findings about black holes are the most important contributions to physics in recent decades. Hence, we appeal the science community to recommend our Hubble-Hawking model for further research and study.

Emission, propagation, and reflection of light as mechanical phenomena in inertial frames are based on the behavior of balls at the limit when their mass is zero. The kinematics of massless balls is like that of balls with mass. Light as a wave or particle is a massless entity. Therefore, it is natural to apply the kinematics of the massless balls to light. Consequently, the kinematics of light depends on its kinetics of electromagnetic nature and its kinematics of mechanical nature in its interactions of emission and reflection with the matter. The study of the physics phenomena in the frame at absolute rest includes those in the inertial frames. Considering this and applying the emission, propagation, and reflection of light as mechanical phenomena in the vacuum of the frame at absolute rest, this study derives formulas for the speed of the wavefront of a ray of light reflected by a fixed and moving mirror when the light comes from a fixed and moving source. The derived formulas apply to the modified Michelson interferometer, employed independently by R. Tomaschek and D. C. Miller in their experiments.

Information is commonly considered as a mathematical quantity that forms the basis of computing. In mathematics, information can propagate instantly, so its transfer speed is not the subject of information science. In all kinds of implementations of computing, whether technological or biological, some material carrier for the information exists, so the information’s propagation speed cannot exceed the speed of the carrier. Because of this limitation, for any implementation, one must consider the transfer time between computing units. We need a different mathematical method to take this limitation into account: classic mathematics can only describe infinitely fast and infinitely small computing system implementations. The difference between the mathematical handling methods leads to different descriptions of the behavior of the systems. The correct handling also explains why biological implementations can have lifelong learning and technological ones cannot. The conclusion about learning evidences matches others’ experimental evidence, both in technological and biological computing.

Derivation of light paths in the Michelson interferometer is based on the hypothesis that the speed of light does not change after reflection by a mirror in motion. The Michelson-Morley experiment predicts a fringe shift of 0.40. The same fringe shift is predicted for a particular Michelson interferometer in which the beam splitter of the interferometer makes an angle of 45° with the direction of light from the source. Light behaves like a wave and also as a particle. Thus, it is reasonable to consider the reflection of light as a mechanical phenomenon. With this hypothesis, the speed of light changes after reflection, and the predicted fringe shift for the particular Michelson interferometer is zero which is in accordance with the result of the Michelson-Morley experiment. Apparently, light travels in any inertial frame as if this particular interferometer belongs to a fixed frame. The velocity of light is considered independent of the velocity of its source, which is in accordance with astronomers’ observations of the binary stars, and the experiment performed at CERN, Geneva, in 1964.

We present a Machian model of Quantum Cosmology with full dark matter and light speed expansion and rotation. During galaxy formation and evolution, fraction of dark matter transforms to visual matter with a relation of the form, m_vis = constant * (m_dark)^2/3. Using this relation and replacing MOND’s ‘critical acceleration’ with “current cosmic maximum angular acceleration”, galactic flat rotation speed range of (50 to 500) km/sec can be fitted well. Estimated flat rotation speeds of DD168, Milky Way and UGC12591 are 49.96 km/sec, 199.66 km/sec and 521.75 km/sec respectively. Based on these striking coincidences, it is possible to say that, MOND’s approach is implicitly connected with cosmological estimation of 95% invisible matter. Considering galactic total matter and current cosmic maximum angular acceleration, galactic working radii, angular velocity and visual matter density can be estimated. Even though, this model is free from ‘big bang’, ‘inflation’, ‘dark energy’, ‘flatness’ and ‘red shift’ issues, at 2.722 K, estimated present Hubble parameter is 66.24 km/sec/Mpc, cosmic radius is 146.3 times the Hubble radius, angular velocity is 146.3 times lower than the Hubble parameter and cosmic age is 146.3 times the Hubble age. With future observations and advanced telescopes, it may be possible to see far distant galaxies and very old stars far beyond the current observable cosmic radius.

The Suter curves for Wh and Wm characteristics of collected and the first time presented Four-quadrant (4Q) diagrams of 11 radial pump-turbine models with different specific speeds (nq=24.34, nq=24.8, nq=27, nq=28.6, nq=38, nq=41.6, nq=41.9, nq=43.83, nq=50, nq=56, and nq=64.04) are given in the paper, as well as the Suter curves for 2 pump models (nq=25, and nq=41.8) which were already published in the literature. These 11+2 curves were analyzed to establish a certain universal law of behavior in dependence on the specific speed. For the determination of existing laws in behavior, the fitting procedure using the Regression and Spline methods was used. The paper presents a research plan and structures that include: data collection of four-quadrant diagrams for models of pump-turbines and pumps with different specific speeds (nq), the procedure of recalculation of Four-quadrant diagrams of the models into Suter curves for Wh and Wm characteristics, the definition of the optimal point for the pump and turbine operating mode in pump-turbine models for different specific speeds, and developing numerical models in the MATLAB program to obtain the Universal Equation for the Wh and Wm characteristics. The scientific contribution of this paper is the firstly published original mathematical curve named Universal Equation for the Wh and Wm characteristics for radial pumps and pump-turbines. Application of the equation has been demonstrated at the pumping station where two radial pumps are installed. The calculation of transient processes was performed using the numerical model developed by the authors in the mathematical program MATLAB. Comparison of the transition process results has been made for the two cases - when input data in the numerical model have been firstly used with the values of Suter curves for Wh and Wm characteristics obtained by recalculation from the Four-quadrant operating characteristics (Q11, n11, M11) of model’s specific speed, and then secondly with the values of the Suter curves for Wh and Wm characteristics obtained from the Universal Equation.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

In France, the regional airport’s demand for services is facing challenges due to the continuous expansion of the high-speed train, high-speed line, and highway networks. This study focuses on the viability of regional airports in France through technical efficiency using data envelopment, principle component analysis, Malmquist productivity index, and regression analysis using bootstrapping. To face the current competitive environment, the regional airports in France adopted strategies, such as the construction of low-cost carrier (LCC) dedicated terminals (LCCTs) with lower expenses to attract more LCCs, increasing non-aeronautical revenue, and hosting regional hubs of LCCs. This is the first study that analyzes all of the French regional airports. The findings indicate that the existence of LCCTs positively affects technical efficiency on the airport’s performance, and share of LCCs at a regional airport leads to neither the efficiency nor the profit level.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

One of the most destructive natural disasters is the earthquake which brings enormous risks to humankind. The objective of the current study was to determine the Earthquake’s remote sensing multiparameter (i.e. land surface temperature (LST), air temperature, specific humidity, precipitation and wind speed) spatiotemporal anomaly of many earthquake samples occurred during 2018 around the world. In this research 11 earthquake (M > 6:0) studied (4 samples selected in a land with transparent sky situations, 3 samples in land within cloudy situations and 4 samples in marine earthquakes). The interquartile range (IQR) and mean ± 2σ methods utilized to improve the efficiency of anomalous differences. As a result, based on the IQR method, negative anomaly before the event detected during the daytime in Mexico and during the nighttime in Afghanistan. In addition, a negative outlier of brightness temperature (BT) detected in Alaska before, after and during the event. In contrast, based on IQR and mean ± 2σ positive anomaly detected in precipitation before and after the event in all investigated examples. According to mean ± 2σ, negative anomaly LST, specific humidity, sea surface temperature (SST_100) and wind detected in most examined earthquake samples. In contrast, positive SST_0 anomaly observed in Fiji and Honduras after the earthquake. Our results suggested in marine earthquakes, for earthquake forecasting we can merge a prior negative anomaly in the wind speed and SST_100. Regarding the in land cloudy sky earthquakes, merging anomaly parameters could be the negative prior anomaly in BT, skin temperature, in contrast, a positive anomaly in precipitation. In land transparent sky earthquake, usually negative prior anomalies in air temperature, specific humidity and LST.

The main objective of this paper is to continue the development of activities of basic and applied research related to wind energy and to develop methods of optimal control to improve the performance and production of electrical energy from wind. A new control technique of Double fed induction generator for wind turbine is undertaken through a robust approach tagged nonlinear sliding mode control (SMC) with exponential reaching law control (ERL). The SMC with ERL proves to be capable of reducing the system chattering phenomenon as well as accelerating the approaching process. A nonlinear case numerical simulation test is employed to verify the superior performance of the ERL method over traditional power rate reaching strategy. Results obtained in Matlab/Simulink environment show that the SMC with ERL is more robust, prove excellent performance for the control unit by improving power quality and stability of wind turbine.

Magnesium nanoparticles of various mean diameters (53 – 239 nm) were synthesized herein via Pulsed Laser Ablation in Liquid (PLAL) from millimeter sized magnesium powders within iso-propyl alcohol. It was observed via a 3x3 full factorial DOE that the processing parameters can control the nanoparticle distribution to produce three size-distribution types (bimodal, skewed and normal). Ablation times of 2, 5, and 25 minutes where investigated. An ablation time of 2 minutes produced a bimodal distribution with the other types seen at higher periods of processing. Mg nanoparticle UV-Vis absorbance at 204 nm increased linearly with increasing ablation time, indicating an increase in nanoparticle count. The colloidal density (mg/ml) generally increased with increasing nanoparticle mean diameter as noted via increasing UV-vis absorbance. High la-ser scan speeds (within the studied range of 3000 - 3500 mm/s) tend to increase the nanoparticle count/yield. For the first time, the effect of scan speed on colloidal density, UV-vis absorbance and nanoparticle diameter from metallic powder ablation was investigated and is reported herein. The nanoparticles formed dendritic structures after being drop cast on aluminum foil as observed via FESEM analysis. Dynamic light scattering was used to measure the size of the nanoparticles. Magnesium nanoparticles have promising use in the fabrication of wearables, such as in conductive tracks or battery electrodes, owing to their low heat capacity, high melting point and bio-compatibility.

An effective process monitoring strategy is a requirement for meeting the challenges posed by increasingly complex products and manufacturing processes. To address these needs, this study investigates a comprehensive scheme based on classical machine learning methods, deep learning algorithms, and feature extraction and selection techniques. In a first step, a novel deep learning architecture based on convolutional neural networks (CNN) and gated recurrent units (GRU) is introduced to predict the local weld quality based on mid-wave infrared (MWIR) and near-infrared (NIR) image data. The developed technology is used to discover critical welding defects including lack of fusion (false friends), sagging and lack of penetration, and geometric deviations of the weld seam. Additional work is conducted to investigate the significance of various geometrical, statistical, and spatio-temporal features extracted from the keyhole and weld pool regions. Furthermore, the performance of the proposed deep learning architecture is compared to that of classical supervised machine learning algorithms, such as multi-layer perceptron (MLP), logistic regression (LogReg), support vector machines (SVM), decision trees (DT), random forest (RF) and k-Nearest Neighbors (kNN). Optimal hyperparameters for each algorithm are determined by an extensive grid search. Ultimately, the three best classification models are combined into an ensemble classifier that yields the highest detection rates and achieves the most robust estimation of welding defects among all classifiers studied, which is validated on previously unknown welding trials.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

Satellite altimetry is successfully developing during the past three decades for the sea level, ocean dynamics, coastal oceanography, planetary waves, ocean tides, wind and wave, ice cover, Earth’s gravity field, and climatology research. We propose a new essential add-on of satellite altimetry related to the peculiarities of the orbits of the Topex/Poseidon and Jasons’ satellite missions which were not mentioned before in the scientific publications. Derived subsets of “self-crossover” and “inter-crossover” points in sub-polar latitudes are discussed in detail in the context of water exchange, and wind-wave dynamics, and potential challenges to be solved. The relatively short time lags between measurements at these crossovers provide additional information on anomalies of magnitudes and directions of ocean currents, and characteristics of wind-driven waves. Resulting data snapshots with constant space and time intervals can be regarded as time series of virtual buoys, an analog of continuous buoy measurements of the sea level, wind speed, and wave height. Areas of the World Ocean where these specific crossovers occur are described in the context of water exchange, wind wave studies, and potential challenges to be solved. The value of these special crossovers for studies and monitoring of the sub-polar seas is illustrated by a case study.