This article presents a field-performance investigation on an Integrated Solar Water Supply System (SWSS) at two isolated agricultural areas in Thailand. The two case-study villages (Pongluek and Bangkloy ) have experienced severe draughts in the last decades, and therefore water supply has become a major issue. A stand-alone 15.36 kW solar power and a 15 kW solar submersible pump were installed along with the input power generated by solar panels supported by four solar trackers. The aim is to lift water at the static head of 64 and 48 m via piping length of 400 metres for each village to be stored in 1,000 m3 and 1,800 m3 reservoirs at an average of 300 m3 and 400 m3 per day, respectively for Pongluek and Bangkloy villages. The case study results have shown that the real costs of electricity generated by SWSS using solar PV systems intergraded with the solar tracking system yield better performance and are more advantageous compared with the non-tracking system. This study illustrates how system integration has been employed. System design and commercially available simulation predictions are elaborated. Construction, installation, and field tests for SWSS are discussed and highlighted. Performances of the SWSS in different weather conditions such as sunny, cloudy, and rainy days were analysed to make valuable suggestions for higher efficiency of the integrated solar water supply systems.

Everyone should therefore consistently get access to enough and safe water. The operation of the existing distribution network as well as the proper optimization and implementation of the new distribution systems are required for a sufficient and safe water supply. In Sekota town sufficient amount of water was not reached to the beneficiaries due to shortage of water at the source. The primary goal of this study was to evaluate the performance and optimize the existing Sekota water supply distribution system using Bentley Water GEMS.The system's hydraulic modeling is carried out by considering as a continuous supply system, and the evaluation procedure used the extended period simulation approach after calibration was done. Calibration is used to ensure the performance of the model using the observed pressure values. The output of the existing system shows pressure is very high means above the maximum pressure and velocity is very low at peak hour demand. The results of velocity and pressure before optimization have negative effect on the performance of the system. The number of pipes and junctions their velocities and pressures which were in admissible ranges are 15 and 42 pipes for velocities and zero and 59 junctions for pressure before and after optimization were evaluated respectively.

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

The issue of water and energy crisis have been turned into global matters which need to be tackled jointly. Accordingly, floating solar power plants, in which photovoltaic modules are used on the surface of water infrastructures, has recently been attracting much interest. This system provides some additional advantages over the ground-based system such as conserving the land and the water and increasing the efficiency of the module. This study first reviews the relevant literature comprehensively and then evaluates the potential of using floating solar photovoltaic (FSPV) on some of Iran’s water infrastructures which have experienced a large amount of evaporation every year due to high solar radiation. To this end, the five important dam reservoirs are selected as the representatives of the five important watersheds in Iran, and the advantages of the FSPV plant is analyzed in terms of energy generation, evaporation reduction, economic and environmental aspects considering different coverage percentages of reservoir’s surfaces. Considering Iran's vast potential for solar radiation, and, on the other hand, huge energy demand and critical water situation, results indicated that Iran can effectively harness solar energy through FSPV systems which help conserve the water in addition to support sustainable energy production.

Shanghai is experiencing water supply problems caused by heavy pollution of its raw water supply, deficiencies in its treatment processes and water quality deteoriation in the distribution system. However, little attention has been paid these problems of water quality in raw water, water treatment and household drinking water. Based on water quality data we show that the raw water sources of the Huangpu River and the Changjiang (Yangtze River) estuary are polluted by microbes (TBC), eutrophication (TP, TN and NH3-N), heavy metals (Fe, Mn and Hg) and organic contamination (chemical oxygen demand [COD], detergent and volatile phenols [VP]). The average concentrations of these contaminants in the Huangpu River are almost double that of the Changjiang estuary forcing a rapid shift to the Changjiang estuary for raw water. In spite of filtering and treatment, TN, NH3-N, Fe, COD and chlorine maxima of the treated water and drinking water still exceed the Chinese National Standard (GB5749). We determine that the relevant threats from water source to household water in Shanghai are: 1) eutrophication arising from highly concentrated TN, TP, COD and algal density in the raw water; 2) increasing salinity in the river estuary, especially at the Qingcaosha Reservoir (currently the major freshwater source for Shanghai); 3) more than 50% of organic constituents and by-products remain in treated water; 4) bacteria and turbidity increase in the course of water delivery to users. The analysis presents an holistic assessment of the water quality threats to metropolitan Shanghai in relation to the city’s rapid development.

Since the energy sector is the main source of greenhouse gases, it has the highest potential for improvement. Improvements can be achieved by generating energy from renewable sources. Combined with thermal energy storage, concentrating solar power plants represent a promising technology for dispatchable renewable energy, ensuring a stable energy supply even in remote areas without contributing to greenhouse gas emissions during operation. However, it is important to note that greenhouse gases and other polluting emissions may occur during the manufacturing process of concentrating solar power plant components. This work analyses the design of the receiver to produce thermal energy for the existing solar dish CSP plant at the Energy Center of the Politecnico di Torino. The objective of this plant is to produce hot water for a small case study. Considering the average solar irradiance for Turin equal to 800 W/m2, the surface heat flux was obtained from the first part of the analysis, which was used to obtain the maximum internal temperature in the receiver equal to 873.7 °C. The maximum temperature obtained was a constraint for the selection of the material for the solar receiver. Of the various possibilities, copper was chosen. In the second part of the work, a Life Cycle Assessment was carried out to compare the emissions generated during the production of the main components of the CSP plant with the emissions generated by the methane-fuelled water heater that produces the same amount of water as the CSP plant. It can be concluded that the manufacture of the main components of the CSP plant results in lower greenhouse gas emissions than the operational phase of a conventional natural gas-fired water heater (1.6 kg CO2/day).

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Abstract: Urban population growth and the expansion of the built environment, pollution, overexploitation of water, inequality in water distribution, and the impacts of climate change in future availability of water, are all elements that jeopardize urban water security. Due to the complexity of urban water systems and their relevance for urban life, a holistic and integrative perspective is therefore needed to address such challenges. In this paper, Urban Water Metabolism (UWM) has been used for comprehensively understanding water (in)security in the City of Puebla (Mexico) and its metropolitan area. Water inflows and outflows have been estimated using a Material Flow Analysis (MFA) method with data either obtained from official sources or simulated with the Monte Carlo method. Our findings show that the UWM configuration in the City of Puebla and its metropolitan area is effective for generating profits to service providers and water related business, yet ineffective to guarantee citizens’ Human Right to Water and Sanitation (HRWS), a right recognized in the Constitution of Mexico. We conclude that to advance towards an inclusive and sustainable provision of water, economic interests must be reconsidered and therefore adjusted so they can be in line with such aspirational socioecological goals. UWM accounting can therefore inform new water governance arrangements, those based on both the best available knowledge and a vibrant participation of all relevant stakeholders.

Origin, mechanics and properties of the Solar System are analysed in the framework of the Complete Relativity theory (by the same author). According to Complete Relativity, everything is relative. Any apparent absolutism (notably invariance to scale of dimensional constants, absolute elementariness, invariance to time) is an illusion stemming from limits imposed by [or on] polarized observers that will inevitably lead to misinterpretation of phenomena (another illusion) occurring on non-directly observable scales or even on observable but distant scales in space or time. If everything is relative, reference frames will exist where particles are planets and where planets are living beings. Earth is, therefore, analysed here in more detail, both as a particle and, as a living evolving being (of, hypothesized, extremely introverted intelligence). The analysis confirms the postulates and hypotheses of the theory (ie. existence of discrete vertical energy levels) with a significant degree of confidence. During the analysis, some new hypotheses have emerged. These are discussed and confirmed with various degrees of confidence. To increase confidence or refute some hypotheses, experimental verification is necessary. Main conclusions that stem from my research and are further confirmed in this paper are: universes are, indeed, completely relative; Solar System is a scaled (inflated, in some interpretations) Carbon isotope with a nucleus in a condensed (bosonic) state and components in various vertically excited states; life is common everywhere, albeit extroverted complex forms are present on planetary surfaces only during planetary neurogenesis; anthropogenic climate change is only a part (trigger from one perspective) of bigger global changes; major extinction events on a surface of a planet are relative extinctions, a regular part of transformation and transfer of life in the process of planetary neurogenesis.

Water supply is a mandatory service for Tanzanians from respective legal public water utilities, and their sustainability reflects implementations of best management strategies at a local level. The objective of this study was to assess current approaches used in water quality and quantity management in Tanzania. This was achieved through secondary water data tends, on-site water quality assessments, visits of respective water supply and sanitation authorities, and assessment of their performances. It was observed that water supplied in rural-based authorities was quite different from that supplied in an urban setting as far as quality and quantity is concerned, urban-based supplies being of assistance to users over rural ones. A new strategy on water management is presented for sustainable water supply in Tanzania; it is based on controlling groundwater abstractions and preference of surface water in public water supplies. Rural water supply management must learn several practices realized at urban supplies for the betterment of respective majority water users.

Our analysis of previous studies shows that solar energy and wind can consume negligible amount of water to generate one megawatt of electricity.

The Roman villa of Pisões (Beja, Portugal), was part of the Lusitanian colony of Pax Iulia. This place stands out for the predominance of the water element in several structures of the villa, highlighting the balneum and the large natatio, one of the largest known in Roman Hispania. The records of the initial excavations that took place since 1967 do not allow the establishment of clear functionalities of the villa. The University of Évora, owner of the site, conceived an action plan for the requalification and enhancement of the archaeological site. One of the tasks aims to investigate using Applied Geophysics. This work analyses the landscape directly related to the villa, given that it is in the flooded area of a river, with a Roman containment dam. It is uncertain whether the water supply comes from this structure or other nearby springs. The use of ground-penetrating radar, combined with unnamed aerial vehicles, all integrated in a geographic information system, allows us to know the location of underground water connections and create a topographic model with high resolution. Considering all the information, we propose a model for the water transport inside the villa and estimate the location of the water supply.

The municipal water supply, related mainly to the cities of Albanian, began to develop in the second half of the 19th century and much intensively after 1945. Today the reported mean water production for the cities, on average, is about 300 l/capita/d including drinking and industrial water supply. The territory of Albania consists of uneven distribution of very heterogeneous aquifers conditioning the reach variety of the municipal water supply solutions. In this article are analyzed and classified the hydrogeological aspects of water supply sources of the settlements, which are summarized in five groups: (a) Wells in alluvial intergranular aquifers; (b) karst springs; (c) wells in karst aquifers; (d) springs in fissured rocks, and (e) mixed water sources. For each group of the water supply sources the main concerns regarding the quantity and quality problems are analyzed facilitated by the description of a variety of representative examples of different situations. Based on the gained experience important recommendation are given for the better understanding of hydrogeological aspects of water supply systems emphasizing the problematics along the river water recharge areas and on the seawater intrusion in coastal aquifers, as well as on transboundary aquifers. However, the main problems of public water supply of Albania remain the poor management of water supply systems which is reflected in the e high water losses, as well as the low public awareness of request for sustainable use.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

This paper proposes the configuration of an Organic Rankine Cycle (ORC) coupled to a solar domestic hot water system (SDHWS), with the purpose of analyzing the cogeneration capacity of the system. A simulation of the SDHWS was conducted at different temperatures, observing its performance to determine the amounts of useable heat generated by the solar collector; thus, from an energy balance, the amount of heat that may be used by the ORC could be determined. The working fluid that would be suitable for the temperatures and pressures given in the system were selected. The best fluid for the given conditions of superheated vapor at 120 °C and 604 kPa and a condensation temperature of 60 °C and 115 kPa was acetone. The main parameters for the expander thermodynamic design that may be used in such ORC were obtained with the possibility of generating 443 kWh of annual electric energy, with 6.65 % global efficiency of solar to electric power, or an overall efficiency of the cogeneration system of 56.35 % with a solar collector of 2.84 m².

The solar cell industry is a part of the green energy sector, and effectively combining the patents of various manufacturers within the supply chain to collectively create sustainable patent market value is of paramount importance. This study aimed to establish a business strategy framework for Project-based licensing through the analysis of solar cell patents and the integration of supply chain manufacturers' patents, with the goal of collectively creating market value for patents sustainably. The research methodology included literature analysis and focus group discussions. Initially, the study analyzed solar cell industry patents from the past decade using the WIPS Global Patent database to identify projects with the highest patent count. Subsequently, through the use of focus group discussions, the feasibility of a patent pool strategy within the supply chain was explored. Finally, a strategy framework was proposed for Project-based patent pool licensing, focusing on the top 15 projects with the highest count of 5,579 patents. The results indicated that adopting this strategy framework for supply chain manufacturer patents can result in higher commercial patent value.

AbstractTo overcome the negative impacts on the environment and other problems associated with fossil fuels have forced many countries to inquire into and change to environmentally friendly alternatives that are renewable to sustain the increasing energy demand. Solar energy is one of the best renewable energy sources with the least negative impacts on the environment. Different countries have formulated solar energy policies to reduce dependence on fossil fuel and increasing domestic energy production by solar energy. According to the 2010 BP Statistical Energy Survey, the world cumulative installed solar energy capacity was 22928.9 MW in 2009, a change of 46.9% compared to 2008. In this study, a PV generation system has been modeled and installed considering uncertain whether based on the hourly wind speed data of New York City (NYC) of year 2014. Regression models has been used to forecast the hourly, weekly, and monthly wind speed of NYC year 2014. Design of experiment (DOE) has been used to determine the optimal panel size (area), the battery capacity size, and other levels of factors.

Rural areas are not only faced with the problems of rural depopulation but also with the problem of water supply and water quality which is a basic necessity of life. In light of this, this paper assesses the rural water supply situation and the bacteriological quality of different water sources in the Obokun Local Government Area of Osun State, Nigeria. The safety of the water sources for human consumption and possible occurrence of the water borne diseases in the study area were determined. The study employed descriptive and analytical methods of data analysis to achieve the objectives of the inquiry. Findings showed that the study area suffered from inadequate water supply and poor locations of the sources of water: The study also revealed that the microbiological quality of the water sources used was unsafe, poor and not acceptable for human consumption. In addition, many man- days-hours were wasted in search of water. It is therefore recommended that the government should make the rural water supply and the maintenance of water quality a priority in its policy formulation.

Technological advances in the last decades have led to the realization of the concept of a smart environment. A significant part of this development is decentralized ledger technology and its variant, a blockchain. The blockchain database is immutable, open to all stakeholders, secure by architecture and robust. Applying a blockchain in water supply sanitary control creates opportunities for optimization, higher quality of service, cost reduction, better sanitary standards and public control. Physical, chemical, and biological water supply contamination is a great source of public health hazards. Implementation of a blockchain for water supply IoT, from the source point to the consumption point, enables effective response to changing environments, possible cross-contamination, stormwater management or disaster and emergency action. The chapter encompasses all fundamental elements and principles of water collection, distribution and consumption, with a focus on the health hazards and sanitary requirements for potable water. The chapter listed the main contaminants, methods of their registration and elimination, and requirements for drinking water in accordance with WHO, EU Drinking Water Directive and EPA standards. Blockchain technology solutions are described for smart water supply, including smart supply management, smart contracts, tokenization, smart compliance systems, and, most importantly, effective utilization of distributed ledger technologies for sanitary monitoring of water sources, water treatment, and water distribution systems.

Phase change materials (PCMs) have emerged as promising solutions for latent heat thermal energy storage (LHTES) systems, offering considerable potential for storing energy derived from renewable sources across various engineering applications. The present study focused on optimization of solar cooling system by integrating LHTES with different PCM tank configuration. TRNSYS simulation software was selected for the study and collected experimental data from laboratory system prototype was used for system validation. The results indicate that the use of PCM led to a noteworthy decrease of 6.2% in auxiliary energy consumption. Furthermore, the duration during which the heat carrier temperature flow exceeded 90°C from the storage tank to the auxiliary heater was extended by 27.8% when PCM was utilized, compared to its absence. The use of PCM in LHTES is more effective under variable weather conditions. On the day when changes in weather conditions were observed, around 98% of the cooling load was provided by produced sun energy. The results of the research can be used to optimize the solar cooling system, which will help reduce the environmental impact of cooling systems running on non-renewable fuels.

In this paper, the experimental results of the thermal sub-system of a reliable and cost-effective polygeneration solar system are presented. This polygeneration system produces heating, cooling and electricity from solar energy, which are used in an existing test-building. Heat is generated in four evacuated tube solar collectors (ETC). The heat may be used for space cooling, through a variable geometry ejector (VGE) heat pump. In order to reduce the mismatches between generation and consumption, two thermal storage tanks were added. The performance of a new thermal storage, with 400 l, able to storage both sensible and latent heat, was tested. Heating performances of the test-building were assessed. Ejector cycle tests were also performed.

Climate change has become the greatest threat to the survival of world and its ecosystem. With the irreversible impact on the ecosystem, problems like rise in sea level, food-insecurity, natural resources scarcity, seasonal disorders have increased over the past few years. Among these problems, the issue of water scarcity due to the lack of water resources and global warming has plagued several nations. Owing to the rising concerns over water scarcity United Nations (UN) has acknowledged water as a primary resource to the development of societies under the ‘Water Goal’ of the sustainable development goals. As the changing climate and intermittent availability of water resources pose major challenges to forecast demand, especially in countries like the United Arab Emirates (UAE) which has one of the highest per capita residential water consumption rates in the world. Therefore, the aim of this study is to propose an accurate water demand forecasting technique that incorporates all significant factors to predict the future water demands of the UAE. The forecasting model used is the Long Short Term Memory (LSTM), with the factors considered are mean temperature, mean rainfall, relative humidity, Gross Domestic Product (GDP), Consumer Price Index (CPI) and population growth. The LSTM model predicts the water demand forecasting in the UAE showing that the future demand will decrease from 1821 million m3 in 2018 to 1809.9 million m3 in 2027.

Water networks are critical infrastructure components, ensuring the continuous supply of high-quality drinking water to consumers. To secure such water supply, regular maintenance, including the replacement of deteriorating pipelines, is essential. In this study, a methodology has been developed for determining optimal pipeline replacement solutions in water supply systems at water utilities with limited data availability. Hydraulic analysis has been conducted on the segment of 25 km of the water supply network using the free software EPANET. Applying water network optimization, eight pipeline replacement projects according to 13 pre-defined criteria have been identified and evaluated. The paper outlines the methods for evaluating the criteria, including defining specific quantitative limits. The Analytical Hierarchical Process (AHP) method was used in the paper to determine the weights of the criteria. The reason for applying this method refers to problems that involve a set of criteria with a mixed structure, including both quantitative and qualitative aspects. Also, the paper describes the steps of the multi-criteria optimization method VIKOR, used to select the optimal project. This paper, considered as case studie, describes a method, i.e. application of a new principles and an innovative way to solve a problem for developing countries.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

This work investigates how to balance the electricity supply and demand in a carbon-neutral northern Europe. Applying a cost-minimizing electricity system model including options to invest in eleven different flexibility measures, cost-efficient combinations of strategies to manage varia-tions are identified. The results of the model are post-processed using a novel method to map the net load before and after flexibility measures are applied to reveal the contribution of each flexi-bility measure. The net load is mapped in the space spanned by the amplitude, duration, and number of occur-rences. The mapping shows that, depending on cost structure, flexibility measures contribute to reduce the net load in three different ways; 1) by reducing variations of long duration but low amplitude, 2) by reducing variations of high amplitude but short duration and low occurrence or 3) by reducing variations of high amplitude, short duration and high occurrence. It is found that cost-efficient variation management is achieved by combining wind and solar power and by combining strategies (1-3) to manage variations. The cost-efficient combination of strategies de-pends on electricity system context where electricity trade, flexible hydrogen and heat production (1) manage the majority of variations in regions with good conditions for wind power while sta-tionary batteries (3) are the main contributors in regions with good conditions for solar power.

The Cauto River Basin (CRB), the heartland of Cuban agriculture, has been hit hard by drought and water shortage. In response to this pressing issue, this study provides a comprehensive as-sessment of water supply, demand and balance within the Cauto River Basin, considering the baseline and projected socio-economic and climatic conditions by coupling of SWAT and WEAP models. The obtained results reveal that the annual flow in the CRB is projected to slightly de-crease (2.5%) in which the reduction in the rainy season (3.1%) is higher than that in the dry sea-son (1.3%). Total water demand in the baseline scenario is around 1.194 billion m3, dominated by agriculture (96%), with rice crop requiring nearly half. For the future scenario of 2050, the study shows a 16.6% surge in demand to 1.394 billion m3, driven by climate change and agricultural expansion. However, domestic use decreases by 10% due to population reduction. Water deficit in the future is projected to increase by 52% from 172.4 to 262.7 million m3 due to rising water demand and declining water supply. This study shows that integrating a hydrological model into a water allocation model is a promising approach to estimate the water supply, demand and balance, which is a crucial component of water resources management.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

This study addresses the prediction of recurring failures in water supply networks, a complex and costly task, but essential for the effective maintenance of these vital infrastructures. Using historical failure data provided by Companhia de Água e Esgotos da Paraíba (CAGEPA), the research focuses on predicting the time until the next failure at specific points in the network. The authors divided the failures into two categories: Occurrences of New Faults (ONF) and Recurrences of Faults (RF). To make the predictions, they used predictive models based on Machine Learning, more specifically on MLP (Multi Layer Perceptron) neural networks. The study revealed that, by analyzing data from past failures and considering factors such as altitude, number of failures on the same street and days between failures, it is possible to achieve an accuracy greater than 80% in predicting failures within a 90-day interval. This demonstrates the feasibility of using fault history to predict future water supply outages with significant accuracy. These forecasts allow water utilities to plan and optimize their maintenance, minimizing inconvenience and losses. The article contributes to the field of water infrastructure management by suggesting that the data-driven approach can be applied in other cities or in networks of different types, such as energy or communication networks. The conclusions highlight the importance of data collection and analysis in preventing failures and optimizing water utilities’ resources.

The future of the Colorado River water supply (WS) affects millions of people and the U.S. economy. A recent study suggested a cross-basin correlation between the Colorado River and its neighboring Great Salt Lake (GSL). Following that study, the feasibility of using the previously developed multi-year prediction of the GSL water level to forecast the Colorado River WS was tested. Time-series models were developed to predict the changes in WS out to 10 years. Regressive methods and the GSL water level data were used for the depiction of decadal variability of the Colorado River WS. Various time-series models suggest a decline in the 10-year-averaged WS since 2013 before starting to increase around 2020. Comparison between this WS prediction and the WS projection published in a 2012 government report (derived from climate models) reveals a widened imbalance between supply and demand by 2020. Further research to update similar multi-year prediction of the Colorado River WS is needed. Such information could aid in management decision making in the face of future water shortages.

The Umbulan Water Supply Project is categorized by the Shipping Infrastructure Acceleration Committee in the list of Accelerated National Strategic Projects through Presidential Regulation Number 3 of 2016 concerning the Acceleration of the Implementation of National Strategic Projects, targeted to operate in mid-2019. This is what will be the focus of the stakeholders of the Umbulan Water Supply Project. This study was to identifying and analyzing networks among stakeholders. Method: This study used a qualitative approach with exploratory methods combined with meta-analysis identification design Identification of stakeholder mapping in the context of early detection of stakeholder involvement in the implementation of the Umbulan Water Supply Project at various levels starting from the National, Provincial (East Java), District/City (Pasuruan, Sidoarjo, Surabaya, to Gresik), Sub-District (Winongan, Gondang Wetan, and Pohtjentrek). The conclusion of this study was based on in-depth interviews and focus group discussions in describing the determination of stakeholders which were divided into two, namely primary stakeholder and secondary stakeholder, and outline the result of the indicators analysis on the stakeholder network of Umbulan Water Supply Project.

Currently, the Israeli energy industry faces the challenge of a considerable increase in solar electricity production. Being a relatively isolated system, the significant expansion of solar electricity may cause problems with electricity quality. The electrical storage installation can resolve this problem. In Israel's situation, the optimal solution can be the creation of a channel between the Mediterranean and the Dead Sea. The channel can solve three closely related problems: the increased production of desalinated water for domestic, industrial, and agricultural needs; the prevention of a permanent Dead Sea level decline and its imminent disappearance; the development of hydro-pumping electrical storage stations; and the creation of numerous PV facilities in the Negev area for national electricity generation. However, a detailed analysis should be done for the estimation of the possible increase of solar electric generation with the consideration of a stochastic PV outcome and a potential ability to use the Dead Sea for the brine discharge from electrical hydro-storage plants.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

This paper aims to investigate the rate of expansion and extraction within the solar system. We carried out the Solar system expansion calculations to do such a review. The Universe is expected to look the same from every point in it. After the big bang, Universe is expanding at some speed. Astrophysicists have been in a race to measure precisely how fast the Universe is expanding since Hubble announced that galaxies were systematically moving away from Milky Way Galaxy with a current speed in 1929. Hubble’s observations came after Einstein’s general relativity, which inspired the big bang theory. According to the Big Bang theory, the Universe has created billions of years ago with an explosion and started to expand until today. The expansion of the Universe mostly happens in vast spaces, so clusters of galaxies move away from each other. For example, raising bread during baking will expand, but the raisings will stay the same size while moving each other to expand the bread. Observers have proven that an object (galaxies, a cluster of planets) held together by gravity has a patch of nonexpanding space produced by a gravitational field. However, some observers claimed the solar system is not expanding, while others claimed it is expanding. Does our solar system expand in an expanding Universe? The cosmological expansion of local systems is reviewed in the modern cosmological models. We showed answers related to this question with the help of literature. This review article revisited the proof of the Solar System’s expansion and its speed with about 0.32 nm/s in an expanding Universe.

The fact that Thailand’s energy policy has set a new renewable energy target of 30% of total final energy consumption by 2036. It also has the potential of solar energy and community demands in remote areas. However, most of the renewable energy technology will still be able to achieve renewable energy goals, similar to the case of the national policy that promotes Solar Home System (SHS) in remote areas, lack of good handling. Therefore, achieving the goal of the renewable energy policy should be in position using the right strategy. This article presents the result of a case study in the Akha upland community, northern Thailand, where we used the mixing method and factor analysis to analyze strategies for SHS related criteria. The key scopes and challenge included bottom-up planning concepts and subsidies from expert persons, while contributions to factors have an impact on developing sustainable SHS, include the creating approval of SHS technologies, developing of SHS management, promoting of SHS technologies, and supporting of SHS policies, respectively. Mainly, social factors provide positive effects, which thus influence the sustainable development of process SHS in terms of the creation of approval. Furthermore, there should be managed appropriately for each community, for the positive imagery of solar power.

This paper attempts to describe the large-scale (solar system-like, astronomical-scale) systems of the known world using the physical models and mathematical tools of relativistic quantum mechanics. The value of H_x can be introduced and approximated as an analogue of the constant ℏ. Based on the quantum mechanical approach, the proper time scale of the solar system can be determined.

One of the most important sources of energy is the sun. Taiwan is located at north 22-25° latitude. Due to its proximity to the equator, it experiences only a small angle of sunlight incidence. Its unique geographical location which can obtain sustainable and stable solar resources. This study takes research on the forecast of solar radiation to maximize the benefits of solar power generation, and develops methods that can predict the future solar radiation pattern to help reduce the costs of solar power generation. This study builds supervised machine learning models, known as deep neural network (DNN) and long short-term memory neural network (LSTM). The hybrid supervised and unsupervised model, namely cluster-based artificial neural network (k-means clustering and fuzzy C-means clustering-based models), was developed. After establishing these models, the study evaluated their prediction results. For different prediction periods, the study selected the best-performing model based on the results and proposed combining them to establish a real-time updated solar radiation forecast system capable of predicting the next 12 hours. The study area covered Kaohsiung, Hualien, and Penghu in Taiwan. Data from ground stations of the Central Weather Administration, collected between 1993 and 2021, as well as the solar angle parameters of each station, were used as input data for the model. The results of this study show that different models have their advantages and disadvantages in predicting different future times. Therefore, the hybrid prediction system can predict future solar radiation more accurately than a single model.

Power generation using renewable technologies has become a primordial option to satisfy the energy demand all over the world, being solar concentrating technologies widely applied for this purpose. A combination of Parabolic Trough Collector with Direct Steam Generation has been considered an excellent option for power generation, due to the economic cost and complexity in the plant are reduced. The thermal evaluation of the solar power plant as well as the PTC in the DSG process is very important in viability and economic analysis. In this sense, as the main objective of this work, a numerical tool for evaluating DSG with PTC technology has been developed. The software SOLEEC is a versatile, reliable, accurate and friendly to the user for thermally evaluating a DSG with PTC technology. The user has the possibility to compare the thermal behavior of different geometrical dimensions for a PTC; and even consider different materials; in order to satisfy the demand of superheated steam by a DSG process. The software has an error less than 5% when compared with literature results and in this paper is used to evaluate a power plant in Mexico obtaining that the change to DSG proposing different PTC could reduce the solar field about 35%.

Despite much published literature on the impacts of agriculture on water quality, knowledge gaps persist regarding which farming systems are of most concern for these relationships, which could help water resource planners better target water management efforts. This study addresses these subjects, seeking to understand how this relationship varies across different farming systems. We used data on water quality status in watersheds of an agricultural region in southern Portugal and crossed it with a map of farming systems for the same region provided by a previous study. By overlaying both data layers, we characterized the areal shares of the farming systems in the watersheds and inspected how these shares relate with water quality status through logistic regression. Results support that the impact of agriculture on water quality is mostly related with specific farming systems. We believe this type of information can be of high interest for agricultural planners and policymakers interested in meeting water quality standards, and we conclude by suggesting innovative policy options based on payments to farmers operating selected farming systems, as a cost-effective way to reconcile agricultural and environmental policy objectives.

Solids in the interstellar medium consist of an intimate mixture of silicate and carbonaceous grains. Because 99% of silicates in meteorites were reprocessed at high temperatures in the inner regions of the Solar Nebula, we propose that similar levels of heating of carbonaceous materials in the oxygen-rich Solar Nebula would have converted nearly all carbon in dust and grain coatings to CO. We discuss catalytic experiments on a variety of grain surfaces that not only produce gas-phase species such as CH4, C2H6, C6H6, C6H5OH or CH3CN, but also produce carbonaceous solids and fibers that would be much more readily incorporated into growing planetesimals. CO and other more volatile products of these surface mediated reactions were likely transported outwards along with chondrule fragments and small Calcium Aluminum Inclusions (CAIs) to enhance the organic content in the outer regions of the nebula where comets formed. Carbonaceous fibers formed on the surfaces of refractory oxides may have significantly improved the aggregation efficiency of chondrules and CAIs. Carbonaceous fibers incorporated into chondritic parent bodies might have served as the carbon source for the generation of more complex organic species during thermal or hydrous metamorphic processes on the evolving asteroid.

This article proposes a new photovoltaic (PV) solar tracker design based on the advantage that installation latitude offers according to efficiency in function of orientation (EFO) of PVs. First, is described a methodology to let incorporate a low-precision, low-cost and high-availability solar tracking mechanism and control system. The design methodology considers the installation location (latitude and azimuth) as a starting point for establishing an adequate angular range of EFO, simultaneity the aspects of available technology and the knowledge accords to developer. Finally, the design technique is experimentally validated by the implementation of a solar tracker at latitude of 28° longitude of 109° and evaluates the efficiency on a specific day. According to result the feasibility of this type of solar tracker for latitudes close to or greater than 30° is highlighted, given that this tracking system costs 30% less than traditional commercial systems as slew drive with its incorporation of lower-resolution azimuth tracking mechanisms. It also increases collection efficiency by 26%, just as continuous or time-based dual-axis solar trackers do, without the more complex controls and mechanisms of these designs.

Over the years, sustainability, impact on the environment, as well as the operation expenditure have been a major concern to the deployment of mobile cellular base stations worldwide. This is because the mobile cellular base stations are known to consume a high percentage of power within the mobile cellular network. Such energy consumption contributes to the emission of Greenhouse Gases (GHG) through the use of conventional diesel generating a set. As a result, the mobile cellular operators are faced with the dilemma of minimising the power consumption, GHG emission, and the operation cost, while improving the Quality of Service of the networks. In attempting to find a solution, this study presents the feasibility and simulation of a solar photovoltaic (PV) with battery hybrid power system (HPS) as a predominant source of power for a specific mobile cellular base station site situated in Soshanguve area of the city of Pretoria, South Africa. It also presents the technical development, showed the environmental advantage and cost benefits of using a solar PV-battery HPS to power a base station site of a 24 hrs daily load of 241.10 kWh/d and the peak load of 20.31 kW as compared to using the HPS of solar PV-diesel generating set-battery. The solar resource pattern for the city of Pretoria was collected from The National Aeronautics and Space Administration and modelled statistically. Thus, the statistical modelling done using solar radiation resource exposure characteristic patterns of Pretoria, South Africa, revealed an average annual daily solar radiation of 5.4645 Wh/m2/d and 0.605 clearness index. The simulation and the design were done using the Hybrid Optimization Model for Electric Renewables and Matlab/Simulink software. The simulation finding shows that the HPS of solar PV-battery combination has about 59.62 % saving on Net Present Cost, Levelized Cost of Energy, and 80.87% saving on Operating cost as against conventional BS powered with Gen Set-Battery.

In this article, the quality of water in the reservoirs of Lake Arpi, Lake Yerevan, Akhuryan, Azat, Aparan and Kechut was estimated with usage of the Armenian Water Quality Index. It was established that in the waters of reservoirs the the maximum permissible concentration of copper, vanadium, aluminum, chromium, manganese, iron, NH4+ and NO2- regularly increases. The following computational algorithm was used for determination of the Armenian Water Quality Index values: to determine the number of cases of MPC excess of i-substance or indicator of water –n; to estimate the total amount of cases of the maximum permissible concentration (N) – N = ∑n; to computes log2N, nlog2n and ∑nlog2n; to determine geoecological syntropy (I) and entropy (H): I = ∑ nlog2n/N and H = log2N – I. Then, Geo-Ecological Evolving Organized index index was determined: G = H/I. Further, the total amount multiplicity of MAC exceedances was estimated: (M) - M=∑m and log2M was computed. Finally, Armenian Water Quality Index was obtained: AWQI = G + 0.1log2M. It was established that the Armenian Water Qquality Index showed a linear dependence on the Water Contamination Index, the Specific Combinatory Water Quality Index, the Geo-Ecological Evolving Organized index and an inverse dependence on the Canadian Water Quality Index.

Solar energy is a renewable and sustainable source of energy, and it has been used in addition of specified technologies, such as solar cooling. The demand for cooling continues to increase in line with environmental changes and a greater desire for human comfort. This study primarily aimed to analyze the performance of an evaporative cooling system powered by solar energy and assess the economic and environmental impact of this system. In this system, hot, dry incoming air is used to evaporate water, thus transforming part of its sensitive heat into latent heat without any variation in enthalpy or total heat. The outputted air then has a lower temperature and a greater humidity, thus providing a more comfortable, healthier environment for its users. To achieve this study’s objectives, numerical code was developed and implemented in MATLAB. The obtained results reveal that the efficiency of the evaporative cooler exceeds 90%, with maximum efficiency being reached at a high wet-bulb depression, while minimum efficiency was observed when the dry air has a high relative humidity and a low dry-bulb temperature.

Conventional models do not fully explain composition of the solar system – for example, the presence of p-nuclei and post-post-Fe-nuclei remains not yet understood (and is one of the great unresolved puzzles of nuclear astrophysics in general); other puzzles exist. We offer a hypothesis which can explain the appearance of non-native elements in the solar system, and a feasible scenario for its implementation. The hypothesis suggests that a nuclear-fission "event" occurred in the inner part of the solar system at the time currently defined as the birth of the system. Conventional models have never considered fission as a contributing nuclei-production mechanism. Upon examination of the existing models and factual data (presented in volumes of publications but never combined into an aggregate), we identified one plausible scenario by which a fission event (not demolishing the entire solar system) could occur: an encounter with a compact super-dense stellar "fragment" (with specific properties) and its "explosion" in fission-cascades. Such scenario also helps resolve other long-standing puzzles of the solar system. For example, it provides that the fission-produced nuclei subsequently transformed into the material that (eventually) accreted into the "rocky" objects in the system (terrestrial planets, asteroids, etc.) and enriched the pre-existed hydrogen-helium objects (the Sun and the gaseous giants) – this offers an explanation for the planets’ inner position and compositional differences within the predominantly hydrogen-helium rest of the solar system. Other implications also follow.

The purpose of this paper is to describe a new way of producing renewable energy based on fjords as a water heater. We will call this system the Water-thermal Energy Production System (WEPS), because the basic idea is to extract heating and cooling energy from water. Although a prototype of WEPS has existed in Norway for more than ten years, a WEPS currently in operation has not been financially analyzed in the literature. Coastal parts of Norway have a potential of 5 TWh of profitable WEPS-facilities [9], due to convenient access to fjords containing water with stable all-season temperatures of about 4–12C when the depth of the water is about 50 meters. This stability of the water temperature makes it possible to extract energy from the fjord in a very efficient way. The potential for economically-profitable WEPS in other parts of the world has not been estimated. In order to answer such a question, more research is required. We have conducted a case study of a WEPS located in the Norwegian municipality of Eid. This is the first full-scale Norwegian WEPS, and it has been operating since 2006. The nascent years have passed, and the technology has been in operation for some years. In this paper, we have made an estimate of the business profitability and the external effects based on past empirical evidence and some assumptions about future development in some key figures. The results suggests that WEPS-Eid has been a profitable investment carrying a positive internal rate of revenue, even if the present underutilization in production capacity will continue in the future. Stability in energy prices for heating purposes has also gained customers compared to the more volatile prices of alternative renewable energy, like hydropower or wind turbines. The negative, external effects in the operating phase from WEPS-Eid are insignificant. Despite the significant profitability of the WEPS facility in Eid, there are two main obstacles for new entrants. There is a lack of relevant operational information for potential investors due to few facilities. This leads to uncertainty, and investments in WEPS appear as a risky business. Secondly, construction of a WEPS requires both big financial investments in digging and facilitating long trenches for a pipeline system and time and effort spent on acquiring the licenses needed for doing this work. A coordinating unit is probably required in order to get the necessary public and private licenses and to reduce fixed costs by coordinating other tasks in the same trenches, like pipes for water and sewer, fiber cables and tele-cables. In Eid, the local municipal administration was the coordinating unit.

This paper investigates the improvement in solar energy collection and conversion using Al₂O₃-Water nanofluids in a solar flat plate collector (SFPC). The efficiency of a solar flat plate collector using water as the fluid medium is analyzed experimentally and theoretically. For theoretical analysis, a mathematical model in MATLAB is used to simulate and is validated by the experimental results. To enhance the solar energy collection and conversion efficiency of the SFPC, Al₂O₃-Water nanofluid was selected as the fluid medium. The nanofluid properties like density, specific heat capacity, thermal conductivity and viscosity are analyzed and compared for several models of Al₂O₃-Water nanofluids and the best model was selected to modify the simulation. Effect of particle diameter in the nanofluid was found to be marginal on the nanofluid properties. The optimum volume concentration of the nanofluid was found to be 4% giving an efficiency increase of 7.78% in the SFPC over the use of water. This reduces the area of the SFPC by 10.5%.

Compound parabolic concentrators are relevant systems used in solar thermal technology. With adequate tailoring, they can be used as an efficient and low-cost alternative in residential water applications. This work presents a simulation study using a ray tracing methodology. With this technique we simulate the interaction between solar rays and solar concentrator to quantify the amount of energy that impinges on the receiver at a particular time. Energy availability is evaluated in a comparison of two configurations: stationary at 21° throughout the year and multi position setup; tilted with respect to the horizontal depending on three seasonal positions: 0° for summer, 16° for spring / autumn and 32° for winter, with the objective of increasing the amount of available energy in each season. The fact that a tracking system can be dispensed with also represents an economical option for the proposed application. The results showed that at 21°, the proposed system works satisfactorily; however, by carrying out the selected angular adjustments, the overall energy availability increased by 22%, resulting in a more efficient option. The methodology developed herein proved to be a valuable tool for prototype design and performance evaluation.

A model is proposed that describes the transfer of ions and the process of water dissociation in a system with a bipolar membrane and adjacent diffusion layers. The model considers the transfer of four types of ions: the cation and anion of salt and the products of water dissociation – hydrogen and hydroxyl ions. To describe the process of water dissociation, a model for accelerating the dissociation reaction with the participation of ionogenic groups of the membrane is adopted. The boundary value problem is solved numerically using COMSOL® Multiphysics 5.5 software. An analysis of the results of a numerical experiment shows that, at least in a symmetric electromembrane system, there is a kinetic limitation of the water dissociation process, apparently associated with the occurrence of water recombination reaction at the of the bipolar region. An interpretation of the entropy factor (β) is given as a characteristic length which shows the possibility of an ion that appeared as a result of the water dissociation reaction to be removed from the reaction zone without participating in recombination reactions.

There is an intense need to optimize agrivoltaic systems. This article describes the invention of a new testing system: the parametric open source cold-frame agrivoltaic system (POSCAS). POSCAS is an adapted gardening cold-frame used in cold climates as it acts as a small greenhouse for agricultural production. POSCAS is designed to test partially transparent solar photovoltaic (PV) modules targeting the agrivoltaic market. It can both function as a traditional cold frame, but it can also be automated to function as a full-service greenhouse. The integrated PV module roof can be used to power the controls or it can be attached to a microinverter to produce power. POSCAS can be placed in an experimental array for testing, agricultural and power production. It can be easily adapted for any type of partially transparent PV module. An array of POSCAS systems al-lows for testing agrivoltaic impacts from the percent transparency of the modules by varying the thickness of a thin film PV material or the density of silicon-based cells, and various forms of optical enhancement, anti-reflection coatings and solar light spectral shifting materials in the back sheet. All agrivoltaic variables can be customized to identify ideal PV designs for a given agricultural crop.

UN 2030 Sustainable Development Goal 6 presents difficulties for small island developing states such as the Kingdom of Tonga, which relies on rainwater and groundwater lenses for freshwater supply. Planning and managing water resources to supply demands in dispersed small islands under variable climate and frequent extreme events is challenging. Tensions between water planning using top-down versus bottom-up processes have long been recognized. Tonga’s overarching national planning instrument is the Tonga Strategic Development Framework, 2015-2025 (TSDFII). This identifies desired national outcomes and is used to direct and resource Ministries and address international and regional commitments. Water supply was a low priority in the three-month consultations that led to TSDFII. Community Development Plans (CDPs), developed by rural villages throughout Tonga’s five Island Groups over nine years, involved participation from 80% of each village population who ranked local priorities. Analysis of priorities in 117 available village CDPs reveals improvements to village water supply was the highest overall priority in all five Island Groups and ranked within the top three priorities by 76% of all villages, with women, youth and men returning figures of 83%, 66% and 80% respectively. The mismatch between top-down and bottom-up priorities appears to result from an urban/rural divide.

Load forecasting is an important component of power system and resource planning for electrical grids. The adoption of electric vehicles (EVs), behind-the-meter (BTM) solar, and heat pumps will significant change the amount and variability of loads. Electrification adoption and load forecasting in arctic regions and Alaska is limited. This paper provides the first load and electrification adoption forecast for the Alaska Railbelt transmission system, including yearly adoption rates of EVs, BTM solar, and heat pumps and hourly load data. Adoption rates are based on available historical data and compared to other regional and national trends. Two forecasts are created: 1) a moderate adoption forecast based on projections from current adoption rates and comparisons to other projections, and 2) an aggressive forecast, which provides a bookend comparison at the high adoption rate of 90% for all technologies. The results of these forecasts demonstrate a significant increase in both energy, 80% and 116% for moderate and aggressive, respectively and peak load demand, 113% and 219% for moderate and aggressive, respectively. Additionally, the results indicate a maximum hourly load change of 260% and 381% for the moderate and aggressive forecasts, respectively. These findings highlight a need for resource planning, which accounts for increases in demand and suggests that significant demand management is needed to smooth and control the load fluctuations as a result of the adoption of EVs, BTM solar, and heat pumps.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

The technologies influencing alternative ways of transportation are augmenting in recent years as the need for transportation is increasing rapidly due to urbanization and motorization. In this paper, a solar powered electric auto-rickshaw (SPEA) is designed and developed for Indian conditions. The developed vehicle is comprehensively analyzed techno-economically for its viability in the Indian market. The performance analysis of SPEA results in an optimal charging rate of 2 kWh per day with an average solar irradiance of 325 W/m2. The discharging characteristics are studied based on different loading conditions. The vehicle achieved a maximum speed of 21.69 km/h with battery discharge rate of 296W at 90kg load and also reached a maximum discharge rate of 540W at 390kg loading with a maximum speed of 12.11 km/h. The environmental analysis of SPEA displayed yearly CO2 emissions of 1,777 kg, 1,987 kg and 1,938 kg using Compressed Natural Gas, Liquefied Petroleum Gas and gasoline engines respectively can be mitigated using SPEA. The results of financial analysis of SPEA were welcoming as the investor gets 24.44% lesser payback duration compared to gasoline run vehicle. Socio-Economic analysis of SPEA discussed its significant advantages and showed 18.73% and 3.9% increase in yearly income over gasoline driven and battery driven vehicles.

Integrated Water Resources Management (IWRM) is one of the system thinking approaches emerged in the 1990s. Since then it has been applied in various countries and contexts. However, the implementation of the IWRM is contested. There are paucity of literature and guidelines as to how the concept can be operationalized. In Ethiopia, there is no evidence that IWRM is successfully instituted. Particularly, IWRM has never been implemented in the Awash River Basin. The study generated data from household and institutional surveys, in-depth interviews, focused group discussions, workshops, and secondary sources. Multiple sources of data were triangulated and thematically summarized. We found that pragmatic water resources management through system approach helps to recognize river basin as a bigger system in which the natural and human systems function. This resolves the problem of fragmentations among among various actors, sectors, interest and priorities. That it facilitates the coordination of various subsystems. The operationalization of IWRM as a system to secure water resources require the establishment and/or strengthening of the interactions of various systems, subsystems, and the elements within the entire basin system. Finally, enabling institutional environments should be considered as a medium of realizing IWRM.

Nitrogen (N) applications can play a key role in achieving profitable wheat production in the low-fertility soils prevalent under rainfed conditions. The model-predicted N partitioning revealed that ammonia-nitrogen (NH4-N) contributed little to the plant N nutrition, and its concentration in the soil remained below 2 ppm throughout the crop season except immediately after the NH4-N based fertilizer application. Nitrate-nitrogen (NO3-N) gradually increased (maximum 144 ppm) with time, especially in the 0-40 cm horizons, and contributed to most N uptake during both seasons at both locations. The N losses from the soil at the medium rainfall site (3.5-20.5 kg ha-1) were mainly attributed to NH4-N volatilization (Nv) and NO3-N leaching (NL) below the crop root zone. Water productivity (8-40 kg ha-1 mm-1) and N use efficiency (31-41 kg kg-1) showed immense variability induced by climate, water availability, and N dynamics in the soil. These results suggest that combining water balance and N modeling can help manage N applications to optimize wheat production and minimize N losses in rainfed agriculture.

Knowledge of water availability in terms of spatial (i.e., depth) and temporal variability of soil water is essential to describe soil water infiltration and storage processes accurately. Therefore, performing simulations of soil water dynamics can be a valuable tool to evaluate different land uses and their impact on water availability. Consequently, this study aimed to model the volumetric soil water content (θ, cm3 cm-3) under agroforestry systems (AFS) with cocoa. For this purpose, the θ was monitored at different depths (0-20, 20-40, 40-60, 60-80, 80-100 cm) in the soil profile of four plots (20 × 50 m) of cocoa under agroforestry systems. Environmental conditions significantly influenced the water balance of the cocoa crop. There were seven moments when evapotranspiration (ET0) was higher than 5 mm d-1. During those moments, the environment exhibited higher PAR values of 1041 µmol m-2 s-1, very low atmospheric relative humidity (RHa) levels (around 45%), higher ambient temperatures of 32.2 ºC and a vapor pressure deficit of 1.6 kPa whose θ levels reached 0.32 cm3 cm-3 and a water balance of -5.7 mm, which presented negative values during most of the study period. The θ obtained from the HYDRUS-1D model presented a slight bias as a high level of coherence between the observed values, based on the model's goodness-of-fit estimators. The above provides accurate simulations of soil water content at various depths, much-needed information for management schemes for cocoa cultivation under agroforestry systems.

Tomatoes, one of the most appreciated vegetables consumed, are crops well adapted for cultivation in arid and semi-arid conditions, the success of large yields is guaranteed by covering water consumption through irrigation. Solar Pumps - SP are driven by Photovoltaic Panels - PV (SPAPV), eliminating the dependence on electricity or diesel; they are environmentally friendly because they generate carbon-free electricity and the cost of operation and maintenance is lower. In order to preserve the water administered by drip to the tomato crop grown in solariums, mulching is used. In Husasău de Tinca, in the Crișurilor Plain, cultivation of tomato varieties without mulching (WM) and with mulching with black foil (MBF) were studied. To answer the question "How effective are water conservation measures in terms of energy independence?", two variants of SPAPVs, direct pumping (ADP) and storage tank (AST) were simulated. Considering the conditions in the solariums, tomato crops do not benefit from the contribution of precipitation, therefore it is proposed to determine the water consumption of tomatoes (ETRo), using the temperatures inside the solarium. In 2016, the average temperatures during the vegetation period were observed with an insurance of over 20 %, the irrigation norms were 6945.7 m3 ha-1, for the WM variant and 6594.0 m3 ha-1 for the MBF variant, respectively. Specific Investment (SI) is 214,795 Euro ha-1 in case of ADP and respectively 202,990 Euro ha-1 in case of ATS. The payback period (IPT) is between 2.68 years and 2.53 years for the ADP variant and between 1.63 years and 1.54 years for the ATS variant, respectively. The indications for water use and irrigation water use show that in the MBF variant the water administered by localized irrigation is better utilized than in the WM variant. In the conditions of Crișurilor Plain, the best solution for the distribution of water in solariums, with the help of SPAPVs is the mulching system of tomatoes grown in solariums (MBF) and the arrangement of the drip irrigation system with a water storage tank (ATS).

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

This study addresses the causal links between external factors and the main hydro-climatic variables. There is a gap in the literature on the description of a complete chain in addressing the structures of direct causal links of solar activity on the terrestrial variables. This is why, the present study uses the extensive facilities of the application of information theory in view of recent advances in different fields. Also, by other methods (e.g. neural networks) first are tested the existence non-linear links of solar-terrestrial influences on hydro-climate system. The results are promising related to the solar impact on terrestrial phenomena which is discriminant in space-time domain. The implications prove robust for determining the causal measure of climate variables under direct solar impact which makes it easier to consider solar activity in climate models, by appropriate parametrizations. This study found that hydro-climatic variables are sensitive to solar impact only for certain frequencies (periods) and these have a coherence with the Solar-Flux only for some lags of the Solar-Flux (in advance).

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

Scales are widely used in many agricultural applications, ranging from weighing crops at harvest to determine crop yields to regularly weighing animals to determine growth rate. In agricultural research applications, there is a long history of measuring crop water use (evapotranspiration) using a particular type of scale called weighing lysimeters. Typically, weighing lysimeters require very accurate data logging systems that tend to be expensive. Recent developments in open-source technologies, such as micro-controllers and Internet of Things (IoT) platforms, created opportunities for developing effective and affordable ways to monitor crop water use and transmit the data to the Internet in near real-time. Therefore, this study aimed to create an affordable Internet of Things (IoT) scale system to measure crop evapotranspiration. A scale system to monitor crop evapotranspiration was developed consisting of an Arduino-compatible microcontroller with cell phone communication, electronic load cells, an Inter-Integrated Circuit (I2C) multiplexer, and analog-to-digital converters (ADC). The system was powered by a LiPo battery, charged by a small (6 W) solar panel. The IoT scale system was programmed to collect data from the load cells at regular time intervals and send the data to the ThingSpeak.com IoT platform. The system performed successfully during indoor and outdoor experiments conducted in 2023 at the Clemson University Edisto Research and Education Center, Blackville, SC. The results from the experiments showed that the IoT scale system could accurately measure crop evapotranspiration using the weighing lysimeter technique.

This paper reviews the design and component of two types of RWHS, namely roof harvesting system (RHS) and pond harvesting system (PHS). The performance in terms of quantity and quality of collected rainwater and energy consumption for RWHS with different capacities were evaluated, as well as the benefits and challenges particularly in environmental, economic and social aspects. Presently, RHS is more commonly applied but its effectiveness is limited by its small scale. The PHS is of larger scale and has greater potentials and effectiveness as an alternative water supply system. Results also indicate the many advantages of PHS especially in terms of economics, environmental aspects and volume of water harvested. While RHS may be suited to individual or existing buildings, PHS has greater potentials and should be applied in newly developed urban areas with wet equatorial climate.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

Almost fifty years after the first installations, I identify the main lessons learned from fighting drought and poverty in Africa with direct solar-powered pumps thanks to Father Bernard Verspieren and Mali Aqua Viva. Six main findings and three main recommendations emerge from the present analysis. They are of direct relevance to all Africa’s countries whose population has gone from 438 million in 1977 to 1,308 million in 2019, with about 600 million still having no access to electricity. In place of “awareness campaigns” and extraordinary courses held by international organizations, I recommend to establish national solar energy institutes whose task will include the education of solar energy professionals giving practice-oriented workshops on solar-powered drip irrigation and rainwater harvesting throughout each Africa’s country. Said education will critically include the economic and social aspects of distributed “generation” of energy and water from sunlight and rainfall.

Solar radiation is the main energy source for mankind and an accurate data of solar radiation levels for a particular location is vital for the optimum operation of solar energy transducers such as photovoltaic cells and solar thermal collectors. In this work, we show that there is a linear relationship between recorded monthly average temperatures and solar radiation in Swaziland. The correlation can be utilized to develop two mathematical models for the estimation of solar radiation: one from the measured monthly average temperatures and the other based on the square-root of the difference between measured maximum and minimum monthly average temperatures. Both models fit the data well and can be applied to estimate solar radiation in other parts of the region.

In a Water-Cooled Lithium-Lead (WCLL) Breeding Blanket (BB), the heat generated by the plasma thermal radiation and nuclear reactions is removed mainly by two components; namely, the First Wall (FW) and the Breeding Zone (BZ). The FW faces the neutrons and charged particles fluxes generated by the fusion reactions and the thermal radiation coming from the plasma. The present work takes into account the FW cooling system inspired by the WCLL BB 2018 design of DEMO 2017 baseline. Unlike the baseline where a Pressurized-Water Reactor (PWR) setup is used for the coolant, various setup between the Boiling Water Reactor (BWR) and the High-Pressure (HP) BWR are studied in the present work operating in the Two-Phase Flow (TPF) regime. The 3D model of the FW in the WCLL BB 2018 design is simplified into a 1D model and a steady state analysis is carried out to optimize the mass flow rate of the water and the number of parallel channels at the BB cells at different poloidal locations of the reactor, which helps not only in reducing the used coolant but also in improving the Tritium Breeding Ratio (TBR). The present work takes into account forced convection in the liquid only region, the subcooled boiling region, and the saturated boiling region using suitable empirical or semi-empirical models from the literature. The results are validated against the existing results in the literature. In the end, related conclusions are made regarding the pros and cons of the studied operating conditions.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

Many of the current strategies for removing pollutants from water are based on nanomaterials and 18nanotechnology. Lower values of Biological Oxygen Demand (BOD5) and Chemical Oxygen De- 19 mand (COD) in water results in reduction in the amount of oxidizable pollutants. We present a study 20 on the reduction of COD and BOD5in water from Wadi El Bey River (Tunisia), using magnetite na- 21 noparticles (MNPs) and magnetic fields. The COD and BOD5 removal reached values higher than 22 50% after 60 min, with optimum efficiency at pH values of ≈8 and for MNPs concentrations of 1 g/L. 23 The use of a permanent magnetic field (0.33 T) showed an increase of COD and BOD5 removal from 2461% to 76% and from 63% to 78%, respectively. This enhancement is discussed in terms of the MNPs 25coagulation induced by the magnetic field and the adsorption of ionic species onto the MNPs sur- 26face due to Fe3O4 affinity.

Water is one of the most critical factors affecting environmental health. For this reason, estimating and monitoring the behavior of water in nature and preventing water pollution before it occurs are advantageous to avoid problems that may occur in terms of environmental health. In order to predict the behavior of water, the hydrological cycle needs to be evaluated on a basin basis. At this point, hydrological models can be used to make mathematical representations of hydrologi-cal processes. These models play an essential role in predicting and monitoring problems such as poor water quality, pollution, particle and sediment transport, and proliferation of oil and petro-leum derivatives among frequently encountered issues in environmental health. In this study, a 2D surface water model was created using soil and water assessment tool (SWAT) to simulate the lotic ecosystem and existing water quality in Tatlıçay Basin and to propose solutions for im-proving environmental health in Cankiri provincial center in Türkiye. The accuracy of the input data and the validity of the model were checked with the calibration and validation studies by using the monthly or 3-monthly observation data of the General Directorate of State Hydraulic Works’ flow observation & water quality stations from 2016 to 2020. The aim was to provide the opportunity to produce fast, accurate, and practical solutions in the face of negative scenarios with this model. This modelling study obtained successful results in the calibration and valida-tion process with very few observed data. With this study, a significant contribution to the litera-ture on environmental health is made, as there aren't many examples of hydrological modeling from the Middle East.

Soil moisture can be an important indicator of climate change in humid and semi-arid areas. This indicator can more efficiently propose different public policies related to climate change than just using precipitation and temperature data. Given the above, the objective of this study is to evaluate changes in soil moisture in the state of Pernambuco during the period 1961-2021, using the System of Hydrological Response Units for Pernambuco. In this study, two river basins in the state of Pernambuco that represent the different climatic conditions of the state will be chosen. The results show that in the coastal region, there is a tendency towards more saturated soils, and in the semi-arid region, there is a tendency towards drier soils. With these results, it is possible to conclude that public policy decisions for the economy, environment, and society must consider this vital water balance variable.

The Cantareira Water Producer System (CWPS), which supplies water to the most populous Brazilian region, Metropolitan Region of São Paulo (MRSP), faces significant challenges due to climate change, threatening its water security. Climate change affects the hydrological cycle affecting water availability. The CWPS is vulnerable to periods of scarcity and instability due to increased climatic variability and increasing water consumption. Current water resource management systems do not consider the impacts of climate change, making it difficult to ensure water security in the future. This study analyzes the impact of climate change on the availability of CWPS using hydrological modeling approach with forecast precipitation data by CMIP6 and assessment of existing systems. The finds will provide a comprehensive understanding of the challenges faced by CWPS in the context of climate change, as well as support strategies and adaptive measures to ensure water security for MRSP.

The South-to-North Water Transfer Jiangsu Water Supply Area (JWSA) is a mega inter-basin water transfer area (water source) that provides water resources from JiangHuai, combines drainage and flooding management, and regulates nearby rivers and lakes. Analyzing the spatiotemporal soil moisture dynamics in the area will inform agricultural drought and flood disaster assessment and early warning studies. Therefore, we evaluated the quality of European Space Agency Climate Change Initiative Soil moisture (ESA CCI_SM) data in the South-North Water Transfer JWSA. Then, we used ensemble empirical modal decomposition, Mann-Kendall tests, and regression analysis to study the spatiotemporal variation in soil moisture for the past 29 years. The CCI _SM data showed a high correlation with local soil measurements at nine sites. We then analyzed the CCI_SM data from three pumping stations (the Gaogang, Hongze, and Liushan stations) in the South-North Water Transfer JWSA. These stations had similar periodic characteristics of soil moisture, with significant periodic fluctuations around 3.1 d. The overall soil moisture at the three typical pumping stations showed an increasing trend. We then investigated whether there were abrupt soil moisture changes at each station. The spatial distribution of soil moisture in the South-North Water Transfer JWSA was characterized by “dry north and wet south”, with higher soil moisture in winter, followed by autumn, and low soil moisture in spring and summer. Although the linear trend of soil moisture in the South-North Water Transfer JWSA varied in significance, the overall soil moisture in the JWSA has increased over the past 29 years. The areas with significantly enhanced soil moisture are mainly distributed in the Yangzhou and Huai'an areas in the southeastern part of the study area. The areas with significantly decreased soil moisture are small in size and mainly located in northern Xuzhou.

This paper aims to study the performance of solar collectors with various sizes under different weather conditions of different Japanese cities, i.e. Kofu city, Nagoya city and Yamagata city. The heat generated from the solar collector was used to conduct a biogas dry reforming reactor in order to produce H2 to feed a solid oxide fuel cell (SOFC). This study has revealed that the output temperature of solar collector, Tfb in April and July was higher than that in January and October irrespective of city. The optimum length of absorber (dx) of the collector was 4 m irrespective of city. It was clarified that Tfb in Yamagata city in January and October, i.e. winter and autumn is lower than that in Kofu city and Nagoya city especially, which is influenced by the tendency of a solar intensity (I) strongly, not velocity of surrounding air (ua). On the other hand, Tfb is almost the same in April and July, i.e. spring and summer, irrespective of city. The amount of produced H2 from the biogas dry reforming reactor and the power generated by SOFC using H2 in spring and summer were higher compared to the other seasons irrespective of city. This study has revealed that the highest available households number per month was 4.7 according to the investigation in this study.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

Tomato brown rugose fruit virus (ToBRFV) is an emerging tobamovirus infecting tomatoes and peppers. Due to its ability to trigger seed contamination, efficient mechanical transmission, and to break the popular resistance genes (Tm-1, Tm-2 and Tm-22), the virus has resulted in a global pandemic on greenhouse tomato production in recent years despite the implementation of strict hygiene and disinfection measures. The objective of this study was to evaluate whether ToBRFV can be transmissible through recirculating hydroponic systems and search for effective approach to contain its spread under such circumstances. We not only detected the presence of ToBRFV in the runoff water solutions collected from ToBRFV-infected tomato greenhouses, but also demonstrated the infectivity of detected virus through initiating ToBRFV infection on tomato plants using bioassay. We then conducted treatment using cold plasma-generated ozone on ToBRFV-contaminated water reservoir and further assessed the efficacy of the treatment to inac-tivate the virus. Results showed the effectiveness of the cold-plasma ozone treatment was de-pendent on the ozone concentrations (0.1 mg/L to 1.0 mg/L), the periods of exposure (24 min to 72 min), and the relative virus titers (1:100 to 1:10,000 - dilution of virus-infected tissue extract), demonstrating the cold-plasma ozone treatment could offer a promising solution to cope with the potential ToBRFV spread through a recirculating hydroponic system in a greenhouse.

Recently it was found from Cassini data that the mean recession speed of Titan from Saturn is v = 11.3 ± 2.0 cm/yr which corresponds to a tidal quality factor of Saturn Q ≈ 100 while the standard estimate yields Q ≥ 6 · 10⁴ . It was assumed that such a large speed v is due to a resonance locking mechanism of five inner mid-sized moons of Saturn. In this paper, we show that an essential part of v may come from a local Hubble expansion, where the Hubble-Lemaˆıtre constant H0 recalculated to the Saturn-Titan distance D is 8.15 cm/(yrD). Our hypothesis is based on many other observations showing a slight expansion of the Solar system and also of our Galaxy at a rate comparable with H0. We demonstrate that the large disproportion in estimating the Q factor can be just caused by the local expansion effect. [Accepted for publication in "Gravitation and Cosmology". The paper is to appear in Vol. 28, Issue 2 (2022) of the journal Gravitation and Cosmology.]

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

Solar flares are broadly classified as impulsive or gradual. Ions accelerated in a gradual flare are thought to be accelerated through a shock acceleration mechanism, but the particle acceleration process in an impulsive flare is still largely unexplored. To understand the acceleration process, it is necessary to measure the high-energy gamma-rays and neutrons produced by the impulsive flare. Under such circumstances, on November 7, 2004, a huge X2.0 flare occurred on the solar surface, where ions were accelerated to energies greater than 10 GeV. The accelerated primary protons collided with the solar atmosphere and produced line gamma-rays and neutrons. These particles were received as neutrons and line gamma-rays, respectively. Neutrons of a few GeV, on the other hand, decay to produce secondary protons while traveling 0.06 au in the solar-terrestrial space. These secondary protons arrived at the magnetopause. Although the flux of secondary protons is very low, the effect of collecting secondary protons arriving in a wide region of the magnetosphere (the Funnel or Horn effect) has resulted in significant signals being received by the solar neutron telescope at Mt. Sierra Negra (4,600 m). This information suggests that ions on the solar surface are accelerated to over 10 GeV with an impulsive flare.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

Arsenic (As) contamination of groundwater is a common problem in BDP. The alkaline pH of the groundwater provides favourable condition for geomicrobiochemical processes, where organic matter also plays an important role in mobilization of As. The total arsenic content (AsT) of the groundwater is in the range of 69-178 µgL-1 with mean value of 118.58 µgL-1. The groundwater quality of monitored drinking water wells are related to local land–use pattern and rural sanitation installation and practices (which can have a strong influence on microbial contamination). The study indicates that As heterogeneity, probably a consequence of microbial heterogeneity is a feature of the study area. The excessive total and fecal coliform (TC and FC) count of the ponds possibly suggest uncontrolled surface run offs and sewage leakage, notably from nearby pit-latrine, which increased the microbial contamination in these water sources. The tube wells located in close proximity (~ 2-3 m) of the surveyed ponds are also contaminated with high TC and FC values, due to faulty water supply system, pond water infiltration and cracked tube well platforms. Coliforms may influence geomicrobiological processes in groundwater and thereby, contribute in As release and mobilization. The TC and FC values of monitored tube wells and ponds show seasonal variation, with high TC and FC values during wet season. Attempt has been made to focus on sanitation risk of the monitored wells (based on sanitation and fecal coliform scores) which is usually less explored. The sanitary risk score reveal the need of immediate attention to all the sites, as 25.0 %, 58.3 %, 11.1 % and 5 % of tube wells of the six sites fell under very high risk (sanitary risk score ≥ 9), high risk (sanitary risk score 6-8), intermediate risk (sanitary risk score 3-5) and low risk category (sanitary risk score 0-2), respectively. Fecal coliform score classified all the sites under intermediate risk category (FC count 10-100 per 100 ml of water). The predominance of As heterogeneity particularly in areas under high risk category (showing high TC and FC contamination) is observed along with the similar sinusoidal pattern of TC, FC and AsT content. Finally, this study shed light on the factors responsible for unsafe nature of monitored tube wells and the influence of anthropogenic activities on the microenvironment of the groundwater, which could be a probable reason behind the As heterogeneity in the groundwater of the study area.

It was for long time believed that lidar systems based on the use of high-repetition micro-pulse lasers could be effectively used to only stimulate atmospheric elastic backscatter echoes, and thus only exploited in elastic backscatter lidar systems. Their application to stimulate rotational and roto-vibrational Raman echoes, and consequently their exploitation in atmospheric thermodynamic profiling, was considered not feasible based on the technical specifications possessed by these laser sources until a few years ago. However, recent technological advances in the design and development of micro-pulse lasers, presently achieving high UV average powers (1-5 W) and small divergences (0.3-0.5 mrad), in combination with the use of large aperture telescopes (0.3-0.4 m diameter primary mirrors), allow to presently develop micro-pulse laser-based Raman lidars capable to measure the vertical profiles of atmospheric thermodynamic parameters, namely water vapour and temperature, both in daytime and nighttime. This paper is aimed at demonstrating the feasibility of these measurements and at illustrating and discussing the high achievable performance level, with a specific focus on water vapour profile measurements. The technical solutions identified in the design of the lidar system and their technological implementation within the experimental setup of the lidar prototype are also carefully illustrated and discussed.

The pressure on freshwater resources is leading to diminishing flows in some of the critical river systems across the globe and India is no exception and this is mainly because of water withdrawal for irrigation, which is often to the tune of 70% to 80% with some proportion for domestic and industrial use. While graduating from the concept of environmental flows and its assessment methodologies in India, the water-managers, the researchers and the conservationists are now moving towards answering the next question if the rivers are to be revived, then where will the water come from, especially in the case of over-allocated rivers, including the river Ganga. While the logical way is to look at the biggest user of water, i.e. irrigation, it remains to be seen whether the irrigation water savings will actually lead to enhancing flows in a river, complementing the efforts towards maintaining e-flows in rivers, or whether it will lead to more area under agriculture, bring changes in cropping patterns towards more water-intensive crops or result in something else. This is a growing debate across the globe, where India is no exception, and there has been a wide range of opinions in this regard. This paper discusses the process, findings and lessons from a joint initiative involving farmers, the Uttar Pradesh state Irrigation and Water Resources Department, Bijnor District Administration and a conservation organisation to enhance flows in a rivulet, called karula River, which is part of the Ganga river system.

The utilization for water resource has been of great concern to human life. To assess the natural water system in Kangding County, the integrated methods of hydrochemcial analysis, multivariate statistics and geochemical modelling were conducted on surface water, groundwater and thermal water samples. Surface water and groundwater were dominated by Ca-HCO₃ type, while thermal water belonged to Ca-HCO₃ and Na-Cl type. The analyzing results concluded the driving factors that affect hydrochemical components. Following the results of the combined assessments, hydrochemcial process was controlled by the dissolution of carbonate and silicate minerals with slight influence from anthropogenic activity. The mixing model of groundwater and thermal water was calculated using silica-enthalpy method, yielding cold-water fraction of 0.56-0.79 and estimated reservoir temperature of 130-199 ^oC, respectively. δD and δ¹⁸O isotopes suggested surface water, groundwater and thermal springs were of meteoric origin. Thermal water should have deep circulation through the Xianshuihe fault zone, while groundwater flows through secondary fractures where it recharges with thermal water. Those analytical results were used to construct a hydrological conceptual model, providing a better understanding of the natural water system in Kangding County.

This study presents application of demand response strategy in a standalone wind-solar-battery hybrid energy system (HES). Inputs for the designed HES are wind speed, solar radiation, temperature and load demand which is variable with time. In this study, hourly values of meteorological data and hourly load demand are considered in one year. An improved gravitational search algorithm (IGSA) is used to optimize the configuration of the standalone wind-solar-battery hybrid power system. The optimal objectives of the system are cost of the system in life cycle, the loss of power supply probability（LPSP）and the energy excess percentage（EXC）.The effect of demand response on economic benefit and energy storage allocation of the standalone wind-solar-battery system is studied. The obtained optimal configuration of the proposed HES can provide minimal energy cost with excellent performance and reduced waste and unmet load.

Water resources worldwide are limited, especially in desert areas like Saudi Arabia. Therefore, the rational and sustainable management of irrigation water supply is an imperative required by the conditions of space and time. This study evaluates the irrigation system through partial root-zone drying (PRD) and regulated deficit irrigation (RDI). The effect of applying the PRD and RDI systems on the efficiency and rationalization of irrigation water consumption in a greenhouse and open field cucumber was studied in addition to using the surface (S) and subsurface (SB) drip irrigation methods on irrigation efficiency. The productivity of the RDI-S regular drip irrigation treatment was considered 100% as the control on which the results of all treatments are measured. The results showed that in terms of irrigation technique, the PRD-SB technique had the highest productivity during the winter season in greenhouse cucumbers, with a general average of 13.8 kg m-2 for all irrigation levels, while the RDI-SB technique had the highest productivity during the summer season, with a general average of 16.1 kg m-2. Regarding irrigation level results, the study showed that an irrigation level of 100% is the highest productivity in all irrigation techniques, with a general average of 14.9 kg m-2 for all irrigation techniques during the winter season and 16.4 kg m-2 during the summer. However, the increase in the irrigation level to 150% did not increase productivity. In comparison, the application of the deficit irrigation technique by reducing the level of irrigation to 50% was not accompanied by a similar decrease in productivity. The study results also showed that irrigation with the PRD-SB system was the most productive in the open field at all irrigation levels, with a general average of 7.3 kg m-2. The general average of the percentage decrease in productivity in all irrigation techniques compared to reducing the irrigation percentage to 50% and 75% was 22% and 3 %. The irrigation efficiencies were higher when applying the PRD (PRD-SB) in winter. In contrast, applying a deficit irrigation system (RDI-SB) in the summer season had the highest efficiency. It could be concluded that using PRD and RDI systems for indoor and outdoor cucumber can save irrigation water.

The assessment of photovoltaic devices, which convert light energy into electricity, becomes significantly relevant due to the aspiration to reduce pollution on a global scale. In this context, the pursuit of optimizing the efficiency in converting light energy into electrical energy involves exhaustive studies and structural analyses of solar cells, all directed toward achieving this goal. This study introduces a research proposal aimed at analyzing the losses associated with series resistance (Rs). The analysis takes into account each component comprising this resistance, pro-posing a network of resistances that precisely models each of these elements. The aforementioned research focused on simple-structured crystalline silicon cells. During this investigation, the junction depth (xj) of n-p materials was varied with the aim of achieving efficiencies in the range of 12%. However, in the pursuit of this desired efficiency, a significant impact on series resistance was observed when analyzing the I-V curves of the cells obtained in each manufacturing process.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.

The Sun is a huge gaseous body. However, we cannot observe events in the inner Sun due to the convection zone opacity according to previous models. Therefore, the flares originate from the front surface of the Sun. But the current study relied on the distance distribution of X-Ray solar flares, which concluded that the inner layers have much lower opacity than expected. It is even less than what was expected by the latest models based on helioseismology. This means that the flares may originate from the solar interior or solar core, and perhaps from the backside surface, and even appear to us from the frontside surface. Which the re-estimate and correct the currently listed solar flare’s location is needed. Additionally, the flare’s distance illustrations the solar interior layers and appears their boundaries from the core to the photosphere. This method allows us to monitor the variation of the core’s radius with time. The model of the flare’s distance has been developed in current study. But this needs to redevelopment after re-estimating the solar flares locations.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

Of all the renewable energy sources, solar photovoltaic (PV) power is estimated to be a popular source due to several advantages such as its free availability, absence of rotating parts, integration to building such as rooftops, and less maintenance cost. The nonlinear current-voltage (I–V) characteristics and power generated from a PV array primarily depend on solar insolation/irradiation and panel temperature. The extracted PV output power is influenced by the accuracy with which the nonlinear power–voltage (P–V) characteristic curve is traced by the maximum power point tracking (MPPT) controller. In this paper, a bio-inspired roach infestation optimization (RIO) algorithm is proposed to extract the maximum power from the PV system (PVS). To validate the usefulness of the RIO MPPT algorithm, MATLAB/Simulink simulations are performed under varying environmental conditions, for example, step changes in solar irradiance, and partial shading of the PV array. Furthermore, the search performance of the RIO algorithm is examined on different unconstrained benchmark functions, and it is that realized that the RIO algorithm has improved convergence characteristics in terms of finding the optimal solution than Particle swarm optimization (PSO). The results demonstrated that the RIO-based MPPT performs remarkably in tracking with high accuracy as the PSO-based MPPT.

Perovskite Solar Cell (PSC) is a third-generation photovoltaic device known for its rapid improvement in efficiency levels over the past decade. Moreover, the added benefits of abundant sourcing of raw materials, uncomplicated fabrication process, organic and inorganic device materials, and tuneable bandgaps make this technology a sustainable energy alternative. However, the efficiency values of these devices are subjected to variation depending on factors such as material compatibility, environmental conditions, energy band alignment of device components and stability characteristics to extrinsic and intrinsic factors. One such vital intrinsic factor is film morphology, homogenous and superior film quality formation and pinhole and trap-free films. In this study, we have investigated the formation of perovskite films on a qualitative basis using metal chloride washing of salts such as Erbium, Antimony, Cadmium and Chromium Chloride. The study aims to analyse the difference in film formation with various metal chloride washing and how this could potentially impact or contribute to photovoltaic performance if the devices are fabricated.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

Abstract: This work is presenting a water level control and monitoring system in a tank, by using the development boards Arduino Uno, NodeMCU ESP8266 and the ultrasonic sensor HC-SR04. The water tank is supplied through a pump controlled by the development board Arduino Uno by means of a relay. The author has issued a control algorithm for controlling the water level and a program in the development environment Arduino IDE that has been implemented and validated on the experimental stand. For monitoring the development board NodeMCU ESP8266 has been used that takes the information from the ultrasonic sensor HC-SR04 and sends it through Wi-Fi to the platform ThingSpeak. Based on the experimental results it has been found out that the water level control system in the tank provides the performances imposed through the designing stage, and the pump running has been automatically stopped when the limit, settled through the program for the water maximum level in the tank, has been reached. The measured value of the water level is shown on the LCD 1602 display. In the water circuit of the home consumers or irrigation systems supplied from the tank a pump controlled by means of a mobile phone has been installed. In order to implement this control system, the author has issued a program for another development board Arduino Uno, whilst for the mobile phone he used the application Arduino Bluetooth Control. The advantage of this water level control and monitoring system in the tank is given by the very low costs in comparison to the cost of an industrial type control system.