The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Two billion people worldwide suffer from anemia with reproductive-age women being disproportionately affected. Iron plays a crucial role in cellular function and impacts cognition, physical function, and quality of life. Iron deficiency (ID) and iron deficiency anemia (IDA) are associated with adverse effects on pregnancy and fetal development. Oral iron supplementation has been the standard treatment for IDA for decades often producing sub-optimal outcomes. Many babies are still being born with ID and suffer adverse sequelae due to inadequate iron levels in the mothers. Is it time to consider broad scale-up of parenteral iron as a new standard of care?

Iron deficiency (ID) is by far the most common nutritional disorder in developing and developed countries. When left untreated, ID leads to anemia. Although the usual recommended treatment for iron deficiency anemia (IDA) is oral iron therapy with countless products, such therapy necessitates administration for >3-6 months with questionable patient compliance since most oral iron products have an unpleasant metallic aftertaste and cause intestinal side effects. In addition, in certain gastrointestinal conditions, such as inflammatory bowel diseases or untreated gluten-sensitive enteropathy, oral iron therapy is contraindicated or unsuccessful. Intravenous iron is considered safe in adults, where adverse events are mild and easily managed. The experience with parenteral iron in children is much more limited and many pediatricians appear reluctant to use it because of uncorroborated fears of serious anaphylactic reactions. In the current article, we thoroughly review the available pediatric literature on the use of all commercially available parenteral iron products except ferumoxytol, which was recently removed from the market. We conclude that parenteral iron appears to be safe in children, it works faster than oral iron and the newer third-generation products allow replacement of the total iron deficit at a single setting.

Introduction: In the recent years alternate day dosing has been recommended in iron deficieny treatment. The aim of this study is to compare the efficacy and side effects of oral iron treatments given daily 1x1, alternate day 1x1 and 2x1 alternate day dosing in iron deficieny anemia patients. Methods: A total of 52 patients with a diagnosis of iron deficiency anemia with serum ferritin level of 25 µg/L or less were included in this retrospective study. Statistical analyzes were done with SPSS V.25. Results: The patients included in our study were between the ages of 18-51. All of the patients included in the study were female. A statistically significant increase was found between 0-14 days(p<0.001), 14-28 days(p<0.001) and 0-28 days(p<0.001) hemoglobin values in all patients. There was no statistically significant difference between 0-14 days (p=0.397) and 0-28 days(p=0.310) ferritin values in all patients. A statistically significant difference was found between 14-28 days(p<0.001) ferritin values. When the rate of change of hemoglobin and ferritin values between the groups was compared and no statistically significant difference was observed between the groups. The rate of change of ferritin values for 14-28 days was significant (p=0.012). There was no significant difference in the frequency of symptoms in the 14th day and 28th day controls for each group (p>0.05). The incidence of metallic taste and bloating symptoms was found to be statistically significant in the third control in the group with 2x1 drug use alternate day (p=0.094). Discussion: The only difference in efficacy was observed in ferritin values between 14th and 28th days. The increase in ferritin values was higher in the group that used 1x1 oral iron every day. However, since no difference was observed between the groups in terms of ferritin and hemoglobin values on days 0 and 28, all three groups were considered equally efficient. Side effects were mainly gastrointestinal side effects. Since the group that received 2x1 oral treatment alternate day had a statistically significantly higher rate of side effects, the patients’ treatment tolerance will be lower compared to the other groups. In conlusion, there is no difference in efficacy and side effects between the patient groups receiving 1x1 daily and 1x1 alternate day oral iron therapy, so 1x1 use alternate day is the most appropriate treatment method for oral iron therapy in terms of patient tolerance, adherence to treatment and pharmacoeconomics.

In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

β-thalassemia, a congenital genetic hematological disorder characterized by decreased or absence of β-globin chains, leads to decrease in levels of Hemoglobin A. The affected individuals can be categorized into two cohorts based on transfusion dependency: transfusion dependent thalassemia (TDT) and non-transfusion dependent thalassemia (NTDT). Remarkably, despite the primary pathology lying in β-globin chain depletion, β-thalassemia exhibits an intriguing association with iron overload. Iron metabolism, a tightly regulated physiological process, reveals a complex interplay in these patients. Over time, both cohorts of β-thalassemic individuals develop iron overload, albeit through distinct mechanisms. Addressing the diverse complications arising due to iron overload in β-thalassemic patients, the utilization of iron chelators has gained a lot of significance. With varying efficacies, routes of administration, and modes of action, different iron chelators offer unique benefits to patients. In the Indian context, three commercialized iron chelators have emerged, showcasing a high adherence rate to the iron chelator-based treatment regimens among β-thalassemic individuals. In this review, we explore the intriguing connection between β-thalassemia and iron overload, shedding light on the intricate mechanisms at play. We delve into the intricacies of iron metabolism, unveiling the distinct pathways leading to iron accumulation in these patients. Additionally, we critically evaluate the therapeutic efficacy of different iron chelators, emphasizing their respective advantages in managing iron overload complications. Through this comprehensive analysis, we aim to deepen our understanding of β-thalassemia and iron overload, paving the way for optimized treatment strategies. Ultimately, our findings provide valuable insights into improving the care and outcomes of individuals affected by β-thalassemia.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented by x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x = 3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

An extension of the Stoney formula for the case of a back side metallized 8” silicon taiko wafer has been developed, in the elastic regime, within the frame of the theory of elasticity. A good correlation between the calculated warpage, determined by the stress released by a given back side metallization (BSM), and the corresponding experimental warpages of the same thick metal layers deposited on an 8” silicon taiko wafer provides evidences of the correctness of the developed theory. This development suggests the possibility to extend this approach to the case of 8” taiko wafers based on a wide band gap semiconductor such as silicon carbide (SiC).

Antarctic krill protein-iron complex and peptide-iron complex were obtained to investigate their iron bioavailability, expression of iron-regulated genes, and in vivo antioxidant capacity. Results indicated that Antarctic krill peptide-iron complex increased significantly the hemoglobin (Hb), serum iron (SI) and iron content in the liver and spleen in iron-deficiency anemia (IDA) mice (P < 0.05) compared with those of Antarctic krill protein-iron complex. Despite the gene expressions of divalent metal transporter 1(DMT1), transferrin (Tf) and transferrin receptor (TfR) could be better regulated by both Antarctic krill peptide-iron complex and protein-iron complex, the relative iron bioavailability of the Antarctic krill peptide-iron complex group (152.53±21.05%) was significantly higher than that of the protein-iron complex group (112.75±9.60%) (P<0.05). Moreover, Antarctic krill peptide-iron complex could enhance the antioxidant enzyme activities of superoxidase dismutase (SOD) and glutathione peroxidase (GSH-Px), reduce the malondialdehyde (MDA) level in IDA mice compared with the protein-iron complex, reducing the cell damage caused by IDA. Therefore, these results demonstrated that Antarctic krill peptide-iron complex could be used as a highly efficient and multifunctional iron supplement.

Background: Iron chelation medications (desferoxamine, desferasirox, desferiprone) are used to manage iron overload. These medications are partially excreted via the kidneys, desferoxamine and desferiprone excretes primarily in the urine, and desferasirox had about 8% excreted in the urine. Their use in severe kidney disease and dialysis patients is caution as “avoided” concerning adverse effects; however, there are reports safe use. This manuscript reviews the literature in this population. Data Sources: Pubmed: desferasirox, deferiprone, deferoxamine, kidney disease, ESKD, Dialysis. Case reports and case series that described experiences with using iron chelation medications in ESKD patients are included. Data also gathered from reading-related sources. Results: This is a review of desferoxamine, desferasirox, and deferiprone use in kidney disease from 1976 to the present time. Table 1 provides a summary of findings. These are mostly reports and brief descriptions of the experiences used in severe kidney disease and dialysis, but lack of randomized control trials and small number of participants. Conclusions: Iron chelation medications are important for treating iron overload but concerns with adverse effects. Due to limited medications available to treat iron overload in patients with severe kidney disease, their safe use has been reporting in the literature. This is an area that warrants further research.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

(1) Background: Ferric carboxymaltose (FCM) is an intravenous (IV) high-dose iron that is effective in the treatment of iron deficiency anemia. This study was to determine if preoperative IV FCM administration could improve recovery from postoperative anemia in patients undergoing revision total joint arthroplasty. (2) Methods: This prospective randomized controlled study analyzed 82 patients undergoing revision total joint arthroplasty during a single hospitalization. Patients in the iron group (n = 41) were administered 1000 mg of IV FCM two weeks preoperatively, while those in the control group (n = 41) were not. Moreover, patients with anemia defined as a preoperative suboptimal Hb concentration &lt;13.0 g/dl were compared according to IV FCM administration. The absolute Hb levels and changes in Hb levels, iron profiles, transfusion rate, and EuroQOL 5-dimension (EQ-5D) scores were compared. (3) Results: There were no significant differences in recovery of Hb levels at each timepoint between the two groups; however, the changes in Hb levels from baseline to four weeks postoperatively showed marginally significant differences favoring the iron group (p = 0.052). However, for preoperatively anemic patients, the change in hemoglobin (Hb) levels between baseline and four weeks postoperatively was significantly better in the iron group than in the control group (iron group [n = 26], −0.3 ± 0.7 g/dL vs. control group [n = 27], −0.9 ± 0.8 g/dL; p = 0.040), although the absolute Hb levels, transfusion rates, and patient quality of life were comparable (all p &gt; 0.05). The iron group showed improved iron metabolite levels including serum ferritin and transferrin saturation four weeks postoperatively, and no adverse events associated with IV FCM administration occurred in either group. (4) Conclusions: Preoperative IV FCM in anemic individuals undergoing revision joint arthroplasty was effective in accelerating recovery from surgery-related anemia by improving Hb levels without any adverse events, despite similar actual Hb levels between the groups. Our findings are clinically relevant and can facilitate determination of the suitability of IV FCM as a safe and reliable protocol for iron supplementation for anemia correction.

In pigs, iron deficiency anemia (IDA) is the most prevalent deficiency disorder during the early postnatal period frequently developing into a critical illness. Meanwhile, in humans, only low-birth-weight infants, including premature infants are especially susceptible to developing IDA. In both human and pig neonates, the initial cause of IDA is low birth iron stores. In piglets this shortage of stored iron results mainly from genetic selection over the past few decades for large litter size and high birth weight. In consequence, pregnant sows cannot provide sufficient amount of iron to the increasing number of developing fetuses. Supplementation with iron is a common practice for the treatment of IDA in piglets. For decades, the preferred procedure for delivering iron supplements during early life stages has been through the intramuscular injection of large amount of iron dextran. However, this relatively simple therapy, which in general, efficiently corrects IDA, may generate toxic effects, and by inducing hepcidin expression, may decrease bioavailability of supplemental iron. New iron supplements are considered now with the aim to combine improvement of hematological status, blunting hepcidin expression, and minimizing toxicity of the administered iron. We propose that iron-deficient piglets constitute a convenient animal model for performing pre-clinical studies with iron supplements.

Bending waveguide is one of the building blocks of on-chip photonic integrated circuits (PICs). Previous bending waveguides (BWs) usually suffer from larger footprint size in the bending region, which is are not conducive to develop large-scale and high-density PICs. To this end, we propose and numerically investigate an ultra-compact silicon-on-insulator 180-degree waveguide bend with a bending radius of 2 µm. Being different from the previous BWs, the design is based on topologically optimized digital metamaterials, which is implemented by using intelligent genetic algorithms. Simulated results show that the proposed structure has a -1.36 dB bend efficiency per 180-degree at a wavelength of 1.55 µm and occupies a footprint of only 4 × 4 µm2. Moreover, the crosstalk is <−20 dB and the loss is <2.6 dB over a >100 nm operating bandwidth (1.6-1.7 µm) for TE0 modes. With the wide operating bandwidth and ultra-compact footprint, the proposed silicon-based 180-degree waveguide bend shows a potential application as the fundamental component for optical communication interconnect in the ultra-highly integrated photonic circuit.

Abstract: This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x=3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. In this report, we study the silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q]. We compute several Zagreb polynomials and Redefined Zagreb indices of these silicon-carbons.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

Inflammation is an underlying problem for many disease states and has been implicated in iron deficiency (ID). This study aimed to determine whether iron status is improved by epigallocate-chin-3-gallate (EGCG) through reducing inflammation. Thirty-two male Sprague-Dawley rats were randomly divided into four groups (n = 8 each): positive controls, negative controls, lipo-polysaccharide (LPS, 0.5 mg/kg body weight), and LPS + EGCG (LPS plus 600 mg EGCG/kg diet). Iron status, hepcidin, C - reactive protein (CRP), serum amyloid A (SAA), and interleukin-6 (IL-6) were measured. There were no differences in treatment groups compared with control in CRP, hepcidin, and liver iron concentrations. Serum iron concentrations were significantly lower in the LPS (p=0.02) and the LPS+EGCG (p=0.01) than in the positive control group. Compared to the positive control group, spleen iron concentrations were significantly lower in the negative con-trol (p<0.001) but not with both LPS groups. SAA concentrations were significantly lower in LPS + EGCG group compared to LPS alone group. IL-6 concentrations were significantly higher in LPS+EGCG (p= 0.004) than in any of the three groups. EGCG reduced SAA concentrations but did not affect hepcidin or improve serum iron concentration or other iron markers.

Dietary iron assimilation is critical for health and essential to prevent iron deficient states and related comorbidities, such as anemia. The bioavailability of iron is limited, while its absorption and metabolism are tightly controlled to keep body iron stores within a relatively narrow range. Genetic inactivation of the iron hormone hepcidin causes hereditary hemochromatosis, an endocrine disorder of iron overload characterized by chronic hyperabsorption of dietary iron, with deleterious clinical complications if untreated. The impact of high dietary iron intake and elevated body iron stores in the general population is not well understood. Herein, we summarize epidemiological data suggesting that high intake of heme iron, which is abundant in meat products, poses a risk factor for metabolic syndrome pathologies, cardiovascular diseases, and some cancers. We discuss clinical relevance and potential limitations of data from cohort studies, as well as the need to establish causality and elucidate molecular mechanisms.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

porous silicon-based photodetectors have attracted more researches due to their high luminous efficiency, good stability and low cost. In this paper, a PbS quantum dots/porous silicon hybrid structure has been fabricated. The PbS quantum dots (QDs) partly infiltrated into the porous silicon (PSi) layer and partly deposited on its surface, which could increase the absorption of near-infrared wavelength range and extend the light absorption in silicon for wavelengths longer than 1100 nm. After that, A metal-semiconductor-metal (MSM) device is fabricated and its response spectrum could extend to the 1200 nm at -3 V. As a silicon-based photodetector (PD), one can envision its role for operation from visible light to short-wavelength infrared range.

The microstructure of the coating during hot-dip galvanizing under industrial conditions of two structural steels, a low-silicon ASTM A36 steel and a high-silicon Q345B steel, both of commercial quality, have been characterized for industrial-relevant times. For both cases it is noted that the formation of the Fe-Zn phases begins in early stages during the heating of the steel, a situation in which all the phases are in the solid state. The characterization was carried out through traditional metallographic techniques including SEM-EDS and DRX equipment. The evolution in time of the microstructure of both steels is examined, being able to observe that the mechanism by which silicon accelerates the formation of Fe-Zn phases in galvanizing is related to the change in the energy of the interfaces caused by a silicon accumulation in the liquid phase in contact with the ζ layer. These results provided us with a deeper understanding of the phase evolution in the hot-dip galvanizing of high silicon steels.

This computational research study will compare the specific charge capacity (SCC) between lithium ions inserted into crystallize silicon (c-Si) nanowires versus sodium ions inserted into amorphous silicon (a-Si) nanowires. It will be demonstrated that the potential energy V(r) within the lithium-silicon nanowire supports a coherent energy state model with discrete electron particles while the sodium-silicon nanowire potential energy will be discovered to be essentially zero and thus the electron current that travels through the sodiated silicon nanowire will be modeled as free electron with wave-like characteristics. This is due to the vast differences in the electric fields of the lithiated and sodiated silicon nanowires where the electric fields are of the order of 1e10 V/m and 1e-15 V/m respectively. The main reason for the great disparity in electric fields are due to the present of optical amplification within lithium ions and the absence of this process within sodium ions. It will be shown that optical amplification develops coherent optical interactions which is the primary reason for the surge of specific charge capacity in the lithiated silicon nanowire. Conversely, the lack of optical amplification is the reason for the incoherent optical interactions within sodium ions which is the reason for the low presence of SCC in sodiated silicon nanowires.

Self-healing is the capability of materials to repair themselves after damage has occurred, usually by interaction between molecules or chains. Physical and chemical processes are applied for the preparation of self-healing systems. There are different approaches for these systems such as heterogeneous systems, shape memory effects, hydrogen bonding or covalent-bond interaction, diffusion and flow dynamics. Self-healing mechanisms can occur in particular by heat and light exposure or by reconnection without direct effect. The applications of these systems display an increasing trend in both R&D and industry sectors. Moreover, self-healing systems and their energy storage applications are currently getting great importance. This review aims to provide general information on recent developments in self-healing materials and their energy applications in view of the critical importance of self-healing systems for lithium-ion batteries (LIBs). In the first part of the review, an introduction about self-healing mechanisms and design strategies of self-healing materials is given. Then, selected important healing materials in the literature for the anodes of LIBs are mentioned in the second part. The results and future perspectives are stated in the conclusion section.

We theoretically investigate and optimize four-wave mixing (FWM) in silicon nitride (SiN) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. Based on extensive previous measurements of the material parameters of the GO films, we perform detailed analysis for the influence of device parameters including waveguide geometry, GO film thickness, length, and coating position on the FWM conversion efficiency (CE) and conversion bandwidth (CB). The influence of dispersion and photo-thermal changes in the GO films is also discussed. Owing to the strong mode overlap between the SiN waveguides and the highly nonlinear GO films, FWM in the hybrid waveguides can be significantly enhanced. We obtain good agreement with previous experimental results and show that by optimizing the device parameters to balance the trade-off between Kerr nonlinearity and loss, the FWM CE can be improved by as much as ~20.7 dB and the FWM CB can be increased by ~4.4 folds, relative to the uncoated waveguides. These results highlight the significantly enhanced FWM performance that can be achieved in SiN waveguides by integrating 2D layered GO films.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

Myelodysplastic syndromes and myeloproliferative neoplasms both represent hematologic diseases associated with bone marrow failure often resulting in anemia. For those patients, transfusion of red blood cell (RBC) units is essential, but results in iron overload (IOL) that may affect various organ functions. Therefore, iron chelation therapy plays a major role in anemic patients, not only because it reduces IOL, but also because it may improve hematopoietic function by increasing hemoglobin or diminishing requirement of RBC transfusions. To assess the utility, efficacy and safety of the different iron chelation medication approved in Germany as well as to examine the effect of chelation on hematopoietic insufficiency, a prospective, multicenter, non-interventional study named EXCALIBUR was designed. In total, 502 patients from 106 German hospitals and medical practices were enrolled. A large proportion of patients switched from deferasirox dispersible tablet to deferasirox film-coated tablet, mainly due to more convenient application which was reflected in the treatment satisfaction questionnaire for medication scores. Iron chelation was effective in lowering serum ferritin levels, with the observed adverse drug reactions being in line with the known safety profile. Hematologic response occurred in a few patients, comparable to other studies that examined hematologic improvement in patients with MDS.

The study, conducted at the Department of Medicine, Maulana Azad Medical College and associated Lok Nayak Hospital, aimed to investigate the prevalence of iron deficiency anaemia among anaemic overweight and obese individuals. Fifty participants were included after screening and consent, undergoing socio-demographic assessment, clinical evaluation, and laboratory investigations. Middle to old-aged individuals predominated (Mean ± SD: 54.54 ± 11.32 years), with females comprising 62%. All subjects were obese (mean BMI: 37.27 ± 5.71 kg/m²), with common comorbidities including hypertension (68%), diabetes (36%), and obstructive sleep apnea-hypopnea syndrome (32%). Nutritional deficiencies, particularly iron deficiency, were prevalent, affecting 62% of subjects, with 48% having iron deficiency alone. Anemia of chronic illness was observed in 38%. Laboratory parameters showed low hemoglobin (8.53 ± 1.23 g/dL), MCV (78.75 ± 10.13 fL), and elevated ESR (20.56 ± 21.47 mm/hour) and CRP levels (4.71 ± 3.32 mg/dL), indicating inflammation. Correlation analyses revealed negative associations between BMI and serum iron/ferritin and positive associations with serum hepcidin. The study underscores the significance of addressing nutritional deficiencies and monitoring iron status in obese populations, suggesting potential associations between obesity and iron metabolism. Further research is needed to explore these relationships for clinical management implications.

Oligodendroglioma (OG) is a brain tumor that contributes to < 1% of brain tumor diagnoses in the pediatric population. Unfortunately, pediatric OG remains without definitive molecular characteristics to aid in diagnosis, and little is known about the tumor microenvironment. Tumor cells' metabolism and proliferation rate are generally higher than healthy cells, so their iron demand is also significantly increased. This consideration underlines the great importance of iron for tumor development and progression. In this context, this study aims to evaluate the effect of iron in a cellular in vitro model of human oligodendroglioma brain tumor. Cell morphology, the effect of siderotic medium on cell growth, iron uptake, and the expression of iron metabolism-related genes were evaluated by optic microscopy, ICP-MS, confocal microscopy, and RealTime PCR, respectively. This study underlines the great importance of iron for tumor development and progression, but also the possibility of reducing the available iron concentration to determine an antiproliferative effect on OGs. Therefore, every attempt can be promising to defeat the OGs for which there are currently no long-term curative therapies.

Baía de Todos os Santos is the second largest bay in Brazil and is home to important ecosystems, including estuarine systems and mangroves. However, studies on the seasonal variability of its soil properties and composition are still scarce. For this study, soil and leaf samples were seasonally collected from mangrove forests at four sites (Cacha Prego, Ponta Grossa, Ilha de Maré, and Pitinga), which are representative of different environmental conditions within the BTS. Soil physicochemical properties, soil composition and partition of Fe forms were determined, and analysis of minerals by Scanning Electron Microscope, was performed on soil samples. Isotopic ratios (δ13C, δ15N) were also determined on soil and leaf samples. Soils showed significant spatial and temporal changes affecting both their properties (pH, Eh) and their composition (TOC, pyrite and Fe oxyhydroxide contents). Clear spatial changes were observed in redox potential, significantly affecting the concentrations of the different geochemical forms of Fe, particularly the concentrations of crystalline oxyhydroxydes and pyrite in one of the studied sites. In three of the study sites, pyrite crystals showed clear evidence of degradation associated with sandy soils. Finally, δ13C and N/C ratios in soils seem to suggest a mixed origin of organic matter.

Beta-thalassemia major (β-TM) is a severe form of thalassemia caused by mutations in the β-globin gene, resulting in partial or complete deficiency of β-globin chains. This deficiency results in oxidative stress, dyserythropoiesis, and chronic anemia. Cytokine dependent hematopoietic cell linker (CLNK) belongs to the adaptor protein family and has the capacity to interact with multiple signaling proteins thereby modulating signal transduction. The aim of the present study was to examine CLNK in sera of β-TM patients and examine its association with iron overload biomarkers. Sixty β-TM patients, aged 3–12 years old and undergoing blood transfusions, and 30 healthy control children were recruited and CLNK, ferritin and iron status parameters were measured. The results showed a significant increase (p < 0.001) in serum CLNK levels in β-TM patients as compared with normal controls. The increased levels of CLNK were significantly associated with increased ferritin levels. Increased CLNK levels in β-TM may be explained by reciprocal effects between immune signaling and immature erythrocytes, which, release soluble receptors and signaling molecules, including CLNK, in the blood.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

Silicon-based thin-films and nanostructures are of paramount importance in a wide range of applications, including microelectronics, photovoltaics, large area sensors, as well as biomedicine. The wide accessibility of silicon and its relatively low cost have driven a continuous improvement of the technology based on this element. Plasma technology has been widely used for the synthesis of coatings and nanostructures based on silicon. Moreover, it has given a fundamental contribution for continuously improving the control of the physicochemical properties of silicon-based materials, and for allowing the synthesis of nanometric structures with well-defined shape and morphology. In this work, we have reviewed the most interesting developments of plasma-assisted processed for the synthesis of Si-based materials, both inorganic and organic, in the last five years. A special attention has been given to the new techniques, or modifications of already existing ones, that open new possibilities for the synthesis of materials with new properties, as well as nanostructures with novel characteristics.

Silicon is an essential trace nutrient for plant growth and is frequently employed to remediate soils contaminated with heavy metals in agriculture. However, silicon’s role and mechanism in reducing heavy metal toxicity have not been well understood, especially for multi-heavy metals. In this study, the effects of silicon-rich materials (silicate, rice husk biochar (RHB), and bentonite) on growth trait, antioxidant response, and heavy metal accumulation and distribution of wheat grown in two soils polluted by multiple heavy metals (Cd, Zn, Pb, and As) were investigated. The results revealed that the addition of silicon-rich materials enhanced plant growth, improved the photosynthetic attributes in leaf tissues, and decreased the contents of Cd, Zn, Pb, and As in wheat shoots and grains. The examination of the subcellular distribution of heavy metals in plants implied that silicon-rich materials transferred heavy metals as intracellular soluble fractions to the cell walls, indicating the reduction of mobility and toxicity of heavy metals in the plants. In addition, the application of the silicon-rich materials reduced oxidative damage in plants by downregulating plant antioxidant response systems and decreasing the production of malondialdehyde (MDA), ascorbic acid (AsA), and glutathione (GSH). Moreover, fractionation analysis of soil heavy metals showed that silicon-rich amendments could convert bioavailable heavy metals into immobilized forms. The results indicated that silicon-rich materials could remediate multi-heavy metal-polluted soils and promote wheat production.

American secularisation is considered a exceptional case in the Western world because of, on the one hand, the softer way it seems to have occurred in relation to other Western countries and, on the other, the fusion it seems to have been done among Judeo-Christian traditions into what is known as American civil religion. The point proposed before is problematic and needs to be called into questions under the light of both the revisions made to the secularization theory by scholars such as Casanova through the interpretation of empirical data collected through the world about the religiosity of people and the multiple works made about the use of “sacred” language in American public life. However, this paper takes those problematic dimensions for granted in order to deepened into what can be considered another secular human endeavour endowed with a religious spirit, namely: the spirit of Silicon Valley. This new secular-sacred narrative is not just American but is being exported as a narrative with “Messianic” traces that seems to aspire to embrace the whole world. Thus, this article explores the origins and evolution of this narrative in the United States, on the one hand, and the expansion of what can be considered a “salvation” ideology abroad that country, on the other.

This paper presents the design, fabrication and characterization of Schottky erbium/silicon photodetectors working at 1.55 µm. These erbium/silicon junctions are carefully characterized using both electric and optical measurements at room temperature. A Schottky barrier ΦB of ~673 meV is extrapolated; the photodetectors show external responsivity of 0.55 mA/W at room temperature under a 8 V of reverse bias applied. In addition, the device performance is discussed in terms of normalized noise and noise equivalent power. To the best of our knowledge, these are the first Er/Si photodetectors designed for operation in free space at 1.55 µm. The proposed devices will pave the way towards development of Er-based photodetectors and light sources to be monolithically integrated in the same silicon substrate and both operating at 1.55 µm.

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. Closed forms of multiplicative degree-based topological indices which are numerical parameters of the structure and determine physico-chemical properties of the concerned molecular compound. In this article, we compute and analyze many multiplicative degree-based topological indices of silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q].

Band-gap alignment engineering has now been extensively studied due to its high potential application. Here we demonstrate a simple route to synthesize two metal oxide layers and align them together according to their bandgaps on surface of crystalline silicon (c-Si) solar cells. The metal oxide layers can not only extend absorption spectrum to generate extra carriers but also serve to separate electron-hole pairs more efficiently. As a consequence, the photovoltaic performance of SnO₂/CdO /Si double-layer solar cell (DLSC) is highly improved compared to CdO/Si and SnO₂/Si single-layer solar cells(SLSCs) and SnO₂/CdO/Si double-layer solar cell (DLSC). By the alignment engineering, the SnO₂/CdO/Si DLSC produces a short circuit photocurrent (J_sc) of 38.20 mA/cm², an open circuit photovoltage (V_oc) of 0.575 V and a fill factor (FF) of 68.7%, corresponding to a light to electric power conversion efficiency (η) of 15.09% under AM1.5 illumination. These results suggest that with the use of metal oxide layers by band-gap alignment engineering, new avenues have been opened for developing high-efficiency and cost-effective c-Si solar cells.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

We successfully created a composite photonic structure out of porous silicon (PSi) microcavities doped by the photochromic protein, photoactive yellow protein (PYP). Massive incorporation of the protein molecules into the pores was substantiated by a 30-nm shift of the resonance dip upon functionalization, and light-induced reflectance changes of the device due to the protein photocycle were recorded. Model calculations for the photonic properties of the device were consistent with earlier results on the nonlinear optical properties of the protein, whose degree of incorporation into the PSi structure was also estimated. The successful proof-of-concept results are discussed in light of possible practical applications in the future.

Electrochemical deposition of silicon at room temperature is problematic due to intrinsically low conductivity of the deposits. This study reports the photoelectrochemical (PEC) deposition of silicon (Si) and silicon–carbon (Si–C) layers from an ionic liquid at temperature 40 oC using silicon tetrachloride (SiCl4) as a silicon precursor. Amorphous layers are deposited on p-type silicon (p-Si), p-type gallium arsenide (p-GaAs), and aluminum–copper alloy AA2024. The semi-conductor substrates are activated by white LED illumination, which generated photoelectrons, thereby making the substrate conductive with respect to the cathodic reaction. Photoresponsive-ness of the deposits is proven by the light-induced photocurrents on an optically inactive substrate made of the alloy AA 2024. The proposed method paves the way for the electrochemical modifica-tion of semiconductors and metals with Si and Si–C structures, which are applicable in various fields, such as; batteries, anti-corrosion coatings, photovoltaics, or PEC electrodes for hydrogen production.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

A distributed bragg reflector is designed to get an optical reflectance on visible electromagnetic spectrum i.e. ~800 nm in this work. Device is realized based on Abele’s matrix for TE mode.

In this work we theoretically investigate the responsivity/noise equivalent power (NEP) trade-off in graphene/semiconductor Schottky photodetectors (PDs) operating in the near-infrared regime and working at room temperature. Our analysis shows as the responsivity/NEP ratio is strongly dependent on the Schottky barrier height (SBH) of the junction and we derive a closed analytical formula for maximizing it. In addition, we theoretically discuss as the SBH is linked to the bias applied to the junction in order to show how these devices could be optimized in practice for different semiconductors. We discover that graphene/n-silicon (Si) Schottky PDs could be optimized at 1550nm showing a responsivity and NEP of 133mA/W and 500fW/Hz, respectively, by a low reverse bias of only 0.66V. Moreover, we show that graphene/n-germanium (Ge) Schottky PDs optimized in term of responsivity/NEP ratio could be employed at 2000nm with a responsivity and NEP of 233mA/W and 31pW/Hz, respectively. We believe that our insights are of great importance in the field of silicon photonics for the realization of Si-based PDs to be employed in power monitoring, lab-on-chip and environment monitoring applications.

Light management in single nanowires (NWs) is of great importance for photovoltaic applications. However, square NWs (SNWs) can limit their light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light management in single silicon NWs with a rectangular cross-section (RNWs). We demonstrate that the RNWs exhibit significantly enhanced light-harvesting compared with the SNWs, which can be attributed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the rectangular cross-section can simultaneously increase the light path length by increasing the vertical side and reshape the LMR modes by decreasing the horizontal side. We found that the light absorption can be engineered via tuning the horizontal and vertical sides, the photocurrent is significantly enhanced by 276.5% or 82.9% in comparison with that of the SNWs with the same side length as the horizontal side of 100 nm or the vertical side of 1000 nm, respectively. This work advances our understanding of how to improve light-harvesting based on the symmetry breaking from the SNWs to RNWs and provides an effective way for designing high-efficiency single NW photovoltaic devices.

The Kerr nonlinear optical performance of silicon nanowire waveguides integrated with 2D layered graphene oxide (GO) films is theoretically studied and optimized based on experimentally measured linear and nonlinear optical parameters of the GO films. The strong mode overlap between the silicon nanowires and highly nonlinear GO films yields a significantly enhanced Kerr nonlinearity for the hybrid waveguides. A detailed analysis for the influence of waveguide geometry and GO film thickness on the propagation loss, nonlinear parameter, and nonlinear figure of merit (FOM) is performed. The results show that the effective nonlinear parameter and nonlinear FOM can be increased by up to ≈52 and ≈79 times relative to bare silicon nanowires, respectively. Self-phase modulation (SPM)-induced spectral broadening of optical pulses is used as a benchmark to evaluate the nonlinear performance, examining the trade-off between enhancing Kerr nonlinearity and minimizing loss. By optimizing the device parameters to balance this, a high spectral broadening factor of 27.6 can be achieved ‒ more than 6 times that achieved in previous experiments. Finally, the influence of pulse chirp, material anisotropy, and the interplay between saturable absorption and SPM is also discussed. These results provide useful guidance for optimizing the Kerr nonlinear optical performance of silicon waveguides integrated with 2D layered GO films.

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

To design and optimize liquid-assisted processes such as reactive infiltration for fabricating refractory SiC/ZrSi₂ composites, basic investigations on the interfacial phenomena occurring when liquid Si-based alloys are in contact with C and SiC substrates, are key steps. Indeed, targeted wettability studies may provide helpful indications for finding the suitable set of operating conditions to succeed the fabrication of composites via the reactive infiltration and for predicting the key influencing mechanisms. The wettability of glassy carbon (GC) by two different Si-rich Si-Zr alloys as a function of the Si-content has been investigated by the sessile drop method at T = 1450°C. The more relevant results obtained in terms of equilibrium contact angle values, spreading kinetics, reactivity and developed interface microstructures are reported in the paper and compared with the behaviour previously observed in the Si-27Zr/GC system. The increase of Si-content only weakly affected the overall phenomena observed at the interface, which from the practical point of view means that even the Si-Zr alloys with higher Si-content, as respect to the eutectic alloy (Si-27Zr), could be potentially used as infiltrant materials.

An amorphous silicon carbide (SiC) membrane with H2 permeance of 1.2E-7 mol･m^-2･s^-1･Pa^-1 and excellent H₂/CO₂ selectivity of 2600 at 673 K was successfully synthesized on a Ni-gamma-alumina-coated alpha-alumina porous support by counter diffusion chemical vapor deposition (CDCVD) using silacycrobutane (SCB) at 788 K. The dominant permeation mechanism for He and H₂ in the temperature range 323-673 K was activated diffusion. The SiC active layer was formed in Ni-gamma-Al₂O₃ intermediate layer. The thermal expansion coefficients mismatch between SiC active layer and Ni-gamma-Al₂O₃-coated alpha-Al₂O₃ porous support was eased by the low decomposition temperature of SiC source and membrane structure.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

Many drastic actions are taken by cocaine users for the sake of experiencing high dopamine levels, which depends on iron for its synthesis. Dopamine depletion and iron deficiency are also involved in the symptoms of restless leg syndrome (RLS). The intersecting biochemical pathways of cocaine use, iron deficiency, and RLS have not been adequately investigated. This case report reveals the successful treatment of a patient with these conditions. A 63-year-old male with a history of cocaine use disorder, insomnia, and RLS sought emergency care for suicidality. Upon admission, he was also found to be iron-deficient. He revealed that his RLS worsened when he attempted to abstain from cocaine. He also used alcohol to sustain the effects of cocaine when the cost of cocaine was too high. During hospitalization, his mood, cravings, and RLS were resolved with adjunctive iron supplementation as well as 300 mg of Wellbutrin. If iron-deficient, replenishment of adequate dopaminergic receptor density and function via supplementation may play an essential role in the prevention of cocaine use and cessation of cocaine withdrawal. Further research is warranted to validate these findings and understand the implications of iron supplementation in addiction medicine.

Iron deficiency anemia (IDA) is a world health problem for humans and other mammals; affecting critical stages of development. Pigs have been used as an experimental model for the study and prevention of anemia because of physiological and metabolic similarities with humans. Iron dextran particles (IDP) are used for intramuscular (IM) IDA treatments in pigs, but are insufficient for prevention of anemia due to quick metabolization. Therefore, the objective of this study was to develop chitosan thermosensitive hydrogels (CTH) formulations and to study their potential as a mammalian parenteral iron dextran supplementation strategy. CTH were loaded with IDP at increasing iron concentrations (0.1, 0.2 and 0.4 g of theorical iron/g of chitosan) and characterized as an IM iron supplement. All the CTH-IDP formulations were thermosensitive and can be injected IM at ~4 °C, with a significant rise in viscosity between 25-37 °C. IDP content was physically trapped in the chitosan hydrophobic gel at 37 °C, without evidence of chemical bonding. We conclude that CTHs are a promising strategy for IM delivery strategy of IDP, and these results may be useful for future iron supplementation studies in pigs, humans and other mammals.

Neurodegeneration with brain iron accumulation (NBIA) is a group of rare neurogenetic dis-orders frequently associated with iron accumulation in the basal nuclei of the brain. Among NBIA subtypes, β -propeller protein-associated neurodegeneration (BPAN) is associated with mutations in the autophagy gene WDR45. The aim of this study was to demonstrate autophagic defects and secondary pathological con-sequences in cellular models derived from two patient harboring WDR45 mutations. Both protein and mRNA expression levels of WDR45 were decreased in patient-derived fibro-blasts. In addition, the increase of LC3B upon treatments with autophagy inducers or inhibitors was lower in mutant cells compared to control cells, suggesting decreased autophagosome formation and impaired autophagic flux. Transmission electron microscopy (TEM) analysis showed mitochondrial vacuolization associated with accumulation of lipofuscin-like aggregates containing undegraded material. Autophagy dysregulation was also associated with iron ac-cumulation and lipid peroxidation. In addition, mutant fibroblasts showed altered mitochon-drial bioenergetics. Antioxidants such as pantothenate, vitamin E and α-lipoic prevented lipid peroxidation and iron accumulation. However, antioxidants were not able to correct the ex-pression levels of WDR45 neither the autophagy defect nor cell bioenergetics. Our study demonstrated that WDR45 mutations in BPAN cellular models impaired autophagy, iron metabolism and cell bioenergetics. Antioxidant partially improved cell physiopathology, however autophagy and cell bioenergetics remained affected.

Wheat (Triticum aestivum L.) being a staple food crop is an important nutritional source providing protein and minerals. It is important to fortify staple cereals like wheat with essential minerals to overcome the problems associated with malnutrition. The experiment was designed to evaluate the status of 11 micronutrients including grain iron (GFe) and zinc (GZn) in 62 wheat cultivars released between 1911 and 2016 in Pakistan. Field trials were conducted over two years and GFe and GZn were quantified by both inductively coupled plasma optical emission spectroscopy (ICP-OES) and energy dispersive X-ray fluorescence spectrophotometer (EDXRF). The GZn ranged from 18.4 to 40.8 mg/kg by ED-XRF and 23.7 to 38.8 mg/kg by ICP-OES. Similarly, GFe ranged from 24.8 to 44.1 mg/kg by ICP-OES and 26.8 to 36.6 mg/kg by EDEXR. The coefficient of correlation was higher for GZn (r=0.90), compared to GFe (r=0.68). Modern cultivars like Zincol-16 and AAS-2011 showed higher GFe and GZn along with improved yield components. Old wheat cultivars WL-711, C-518 and Pothowar-70 released before 1970 also exhibited higher value of GFe and GZn, however their agronomic performance was poor. Multivariate analysis using ten micronutrients (Al, Ca, Cu, K, Mg, Mn, Na and P) along with agronomic traits, and genome-wide SNP markers identified the potential cultivar with improved yield, biofortification trait and wider genetic diversity. Genetic gain analysis identified significant increase in grain yield (0.4% year-1), while there was negative gain for GFe (-0.11% year-1) and GZn (-0.15% year-1) over the span of 100 years. The Green Revolution Rht-B1 and Rht-D1 genes had strong association with plant height, and grain yield (GY), while semi-dwarfing alleles had negative effect on GFe and GZn contents. This study provided a valuable insight into biofortification status of wheat cultivars deployed historically in Pakistan and is a valuable source to initiate a breeding strategy for simultaneous improvement in wheat phenology and biofortification.

Iron (Fe) is a trace element that plays essential roles in various biological processes such as DNA synthesis and repair, as well as cellular energy production, or oxygen transport, and it is currently widely recognized that iron homeostasis is dysregulated in many cancers. Indeed, several iron homeostasis proteins may be responsible for malignant tumor initiation, proliferation, and for metastatic spread of tumors. A large number of studies demonstrated the potential clinical value of turning these deregulated proteins as prognostic and/or predictive biomarkers of malignancy and /or response to anticancer treatments. Additionally, the iron addiction of cancer cells and the importance of iron in ferroptosis cell death signaling pathways prompted the development of therapeutic strategies against advanced stage or resistant cancers. In this review, we selected relevant and promising studies in the field of iron metabolism in cancer research and clinical oncology. Besides, we discuss some co-existing discrepant findings. We will also present and discuss the latest lines of research related to targeting iron, or its regulatory pathways, as potential promising anti-cancer strategies for human therapy. Iron chelators, such as deferoxamine or iron-oxide based nanoparticles, which are already tested in clinical trials, alone or in combination with chemotherapy will also be reported.

Background: Essential hypertension is a major public health associated with increase pressure on the vascular walls and red blood cells (RBCs). In the present work, osmotic fragility (OF) of RBCs was reexamined in the means of its correlation with two risk factor; iron status and lipid profile. Experimental: OF, iron status parameters, and lipid profile components were measured in 60 patients and compared with the results of 30 controls. Results: The results showed a significant increase in all iron indices of hypertensive patients in comparing with healthy control group except TIBC, UIBC, and transferrin concentrations, which decrease in these patients in comparing with control group. Serum TGs, total cholesterol, VLDLc, and LDLc were increased while there is no significant in serum HDLc in patients to comparing with control group. There is no significant change in OF between patients and controls where p=0.173. The iron status parameters and lipid profile components were dependent on sex and smoking state. Hemoglobin and PCV were correlated significantly with total cholesterol and LDLc. Transferrin saturation showed a positive correlation with cholesterol, LDLc, and TGs, but negatively correlated with HDL_c. No significant correlation between all the measured parameters and OF in HT patients. There is a significant correlation between serum ferritin and systolic BP and between Hb and systolic BP. Conclusion: No significant effect on the OF in HT patients. HT patients have elevated level of iron parameters in comparing with controls. OD has no correlation with iron status parameters or with lipid profile components.

Iron deficiency in the fetal and neonatal period (perinatal iron deficiency) bodes poorly to neuro-development. Given its common occurrence and the negative impact on brain development, a screening and treatment strategy that is focused on optimizing brain development in perinatal iron deficiency is necessary. Pediatric societies currently recommend a universal iron supple-mentation strategy for full-term and preterm infants that does not consider individual variation in the body iron status and could lead to under-treatment or over-treatment. Moreover, the focus is on hematological normalcy and not optimal brain development. Several serum iron indices and hematological parameters in the perinatal period are associated with risk of abnormal neurodevelopment, suggesting their potential use as biomarkers for screening and monitoring treatment in infants at risk for perinatal iron deficiency. A biomarker-based screening and treatment strategy that is focused on optimizing brain development will likely improve outcome in perinatal iron deficiency.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

The study of co-fusion was one of the essential topics in the history of metallurgy in China. Simulation experiments had been an essential concept in the study of the co-fusion steelmaking process. This paper mainly studied the simulation experiments of co-fusion from two aspects: the replication of co-fusion swords by three different methods, and the micro-analysis of the co-fusion samples. The experimental results indicated that several co-fusion swords could be made by different processes, but the carbon content and surface hardness were quite different. During repeated forging welded, the microstructure of the samples transformed from laminated to homogenized, finally the steel with a uniform carbon content was obtained. It was challenging to find the characteristics of co-fusion from the homogenized samples. The results prompted people to rethink the microstructure characteristics of ancient co-fusion artifacts.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Drought is an important factor seriously affects agricultural production worldwide. Agricultural practices that can increase resistance to drought are gaining importance. In this study the role of nano-silicon dioxide (NaSiO2) in countering drought stress in invitro strawberry plantlets were investigated. In the experiment, the effects of PEG 6000 concentrations (0, 4, 8%) and NaSiO2 concentrations (0, 50, 100 mg L-1) on invitro strawberry plants were determined. Plantlets treated with PEG 6000 showed reduced vegetative growth parameters, but this decrease was reduced with NaSiO2 application. NaSiO2 at 50 mg L−1 induced the maximum shoot and root fresh weight (1.20 g, 1.24 g, respectively) and length (40.09 mm, 34.26 mm, respectively), leaves number (16.67 pieces/plant) and SPAD index 53.57 among 4% and 8% PEG applications. When the SOD and CAT activities were examined, the results showed that application of NaSiO2 enhancement drought stress tolerance by promoted certain antioxidant response by increasing SOD and catalase (CAT) activities under drought stress. According to the results NaSiO2, limited the devastating impact of drought stress and markedly enhanced all the examined parameters.

The fabrication of thin-film multilayer structures by sputtering technique usually requires multi-cathode deposition machine. This study proposes a simpler approach based on the RF power modulation: silicon nitride (SiN$_x$) thin films were prepared by RF reactive sputtering in (Ar + N$_2$) atmosphere at room temperature. The samples were analyzed to highlight the effects of different deposition conditions on the morphological and optical properties of the films in the visible and near/mid-IR regions. The refractive index of the films was changed in the range of 1.5 - 2.5 (at $\lambda$=800 nm) by tuning the sputtering power. IR reflectance measurements revealed the absence of spurious (oxygen- or hydrogen-based) phases, while atomic force and scanning electron microscopies confirmed the presence of flat and defect-free samples surfaces.

The tandem Solar cell has high power conversion efficiency (PCE), so they are taken as the next step in photovoltaic evolution. The tandem solar cell also overcome the limitations of Single-junction solar cells by reducing thermalization losses and also reduce the fabrication cost. The fabrication of tandem solar cells is highly efficient after the origination of halide perovskite absorber material, this material will shape the future of tandem solar cells. Researchers have already shown that this material can convert light more efficiently than standalone sub cell. Today, researchers around the world are keeping the configuration of a tandem solar cell as their agenda. A Tandem solar cell is a stacking of multiple layers having different bandgaps with specific maximum absorption and width. We reviewed perovskite/silicon tandem solar cells with different sub-module configurations. Move forward, we discuss the tandem module technology, sub cell of a tandem can be wired in several ways two terminals 2T monolithic and mechanically stacked, a four-terminal 4T mechanically stacked, and three-terminal 3T monolithic stack devices. This review paper provides a side-by-side comparison of theoretical efficiencies of multijunction solar cells. The highest efficiency has been evaluated at 39.4% for a three-level structure.

Single nanowires (NWs) are of great importance for optoelectronic applications, especially solar cells serving as powering nanoscale devices. However, weak off-resonant absorption can limit its light-harvesting capability. Here, we propose a single NW coated with the graded-index dual shells (DSNW). We demonstrate that with appropriate thickness and refractive index of the inner shell, the DSNW exhibits significantly enhanced light trapping compared with the bare NW (BNW), and the NW only coated with the outer shell (OSNW) and the inner shell (ISNW), which can be attributed to the optimal off-resonant absorption mode profiles due to the improved coupling between the reemitted light of the transition modes of the leak mode resonances of the Si core and the nanofocusing light from the dual shells with the graded refractive index. We found that the light absorption can be engineered via tuning the thickness and the refractive index of the inner shell, the photocurrent density is significantly enhanced by 134% (56%, 12%) in comparison with that of the BNW (OSNW, ISNW). This work advances our understanding of how to improve off-resonant absorption by applying graded dual-shell design and provides a new choice for designing high-efficiency single NW photovoltaic devices.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.

In this paper, we present a study of various ZnO/SiO2-stacked thin film structures for flexible micro-energy harvesting devices. Two groups of micro-energy harvesting devices, SiO2/ZnO/SiO2 micro-energy generators (SZS-MGs) and ZnO/SiO2/ZnO micro-energy generators (ZSZ-MGs), were fabricated by stacking both SiO2 and ZnO thin films, and the resulting devices were characterized. With a particular interest in the fabrication of flexible devices, all the ZnO and SiO2 thin films were deposited on ITO-coated PEN substrates using an RF magnetron sputtering technique. The effects of the thickness and/or position of the SiO2 films on the device performance were investigated by observing the variations of output voltage in comparison with that of a control sample. As a result, compared to the ZnO single-layer device, all the ZSZ-MGs showed much better output voltages, while all the SZS-MG showed only slightly better output voltages. Among the ZSZ-MGs, the highest output voltages were obtained from the ZSZ-MGs where the SiO2 thin films were deposited using a deposition power of 150 W. Overall, the device performance seems to depend significantly on the position as well as the thickness of the SiO2 thin films in the ZnO/ SiO2-stacked multilayer structures, in addition to the processing conditions.

A simple fabrication method in the surface modification of electroosmotic silicon microchannel using thermal dry oxidation is presented. The surface modification is done by coating the silicon surface with a silicon dioxide (SiO₂) layer using thermal oxidation process. The process is aimed not only to improve the surface quality of the channel to be suitable for electroosmotic fluid transport but also to reduce the channel width using a simple technique. Initially, the parallel microchannel array with dimensions of 0.5 mm length and width ranging from 1.8 µm to 2 µm are created using plasma etching on the 2x2 cm <100> silicon substrate. The oxidation of silicon channel in a thermal chamber is then conducted to create the SiO₂ layer. The layer properties and the quality of the surface are analyzed using SEM and surface profiler, respectively. The results show that the maximum oxidation growth rate occurs in the first 4 hours of oxidation time and the rate decreases by time as the oxide layer becomes thicker. It is also found that the surface roughness is reduced with the increase of process temperature and oxide thickness. The scallop effect on the vertical wall due to plasma etching process also improved with the presence of the oxide layer. After the oxidation, the channel width is reduced by ~40%. The demonstrated method is suggested for the fabrication of a uniform channel cross section with high aspect ratio in sub-micro and nanometer scale that will be useful for the electroosmotic flow (EOF) manipulation of the biomedical fluid sample.

Neural microprobes represent an important component of neural prosthetic systems where implanted microprobes record the electro-potentials generated by specific thoughts in the brain and convey the signals to algorithms trained to interpret these thoughts. Here, we present novel elongated multi-site neural probe that can reach depths greater than 10mm. We hypothesize that reaching such depth allows the recording of cognitive signals required to drive cognitive prosthetics. The impedance of the recording sites on the probes was on the order of 500 kΩ at 1 kHz, which is consistent with probes used for neurophysiological recordings. The probes were made porous using Xenon Difluoride (XeF₂) dry etching to improve the biocompatibility and their adherence to the surrounding neural tissue. Numerical studies were performed to determine the reliability of the porous probes. We implanted the elongated probe in rats and show that the elongated probes are capable of simultaneously recording both spikes and local field potentials (LFPs) from various recording sites.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

The aim of the study was to investigate the association between maternal dietary iron intake during pregnancy and the gut microbiota characteristics of both the mother and neonate in a well-characterized cohort. A total of 95 mother-neonate dyads were included in our study, with basic information collected through questionnaires. A semi-quantitative Food Frequency Questionnaire (FFQ) was used to assess maternal dietary intake during pregnancy, and maternal dietary iron intake was categorized into &lt;20 mg/d and ≥20 mg/d groups. Fecal samples were collected from the mother in the third trimester and the neonate, allowing for assessment of the community profile and diversity of gut microbiota via 16S rRNA amplicon sequencing. Then, a comparison between different maternal dietary iron intake groups was conducted, adjusting for delivery mode (VD, vaginal delivery; CS, cesarean section) and other potential confounding factors. No significant differences in community profile and diversity were observed for the maternal gut microbiota in different dietary iron intake groups. In neonate fecal samples, the Shannon (P = 0.044) and Simpson (P = 0.010) diversity indices of the gut microbiota were higher in the maternal dietary iron intake ≥20 mg/d group, while Simpson diversity presented the same tendency in vaginal delivery (P = 0.041) after stratification. The relative abundance of the core genus Bifidobacterium showed a significant difference between groups (4.69 [1.19–12.77] vs. 13.98 [3.44–27.28]; P = 0.044). The abundance of Lactobacillus was different in the ≥20 mg/d group under both delivery modes (VD: beta = 2.9, w = 4.13; CS: beta = 2.77, w = 3.8). Our findings suggest that adequate dietary iron intake during pregnancy may promote beneficial bacterial colonization and increase the biodiversity of the neonate gut microbiota.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

Keywords: iron deficiency anemia; IDA; anemia; knowledge; awareness.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

INTRODUCTION. The most common cause of eating non-food items (pica) is specific deficiencies of minerals, such as iron. This study aimed to assess the relationship between Pica and Iron deficiency anemia among pregnant women. METHODS. The study was conducted in the out-patient department, antenatal Clinic at East Jeddah Hospital from July to September 2020. Design: A quantitative descriptive correlation design. Sample size: A total of 400 pregnant women, included anemic pregnant women, ≥ 18 years old, with singleton fetus and iron deficiency anemia. RESULTS. The mean age was 32.2 ± 6.6, half of the participants reported food cravings. Ice was the main item in pica followed by clay and chalk. Two-thirds had pica, more than half during the 1st trimester. There is a statistically significant relationship between pica and the history of a family member, parity, and gravidity at (P< 0,001, P <0,001, P <0,005) respectively. Hb and hematocrit in relation to pica reflected a statistically significant relationship (P< 0,001) and (P< 0,001), respectively. The symptoms attributed to iron deficiency were significantly associated with pica (P< 0,006). CONCLUSION. The pica and iron deficiency anemia had a significant association with pregnant women in EJH. RECOMMENDATION. The follow-up visits should integrate the food behavior inquiry to check if the pica existing with anemic or non-anemic pregnant women. Also, increase the awareness among midwives-nurses about the prevalence of pica and iron deficiency anemia among pregnant women.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

Beta thalassemia major (β-TM) disorder characterized by the lack, or severe reduction in the production of hemoglobin β-globin chains. The standard protocol for the management of β-TM is blood transfusion and iron chelation therapy to reduce the iron overload state. The present study aimed to investigate the relationships between two iron regulatory hormones, hepcidin (HEPC) and erythroferrone (ERFE) levels and iron status parameters (ISPs) in Iraqi patients with β-TM. ISPs and hormones were measured in sixty patients and compared with thirty healthy controls. The results indicated significant changes in different iron status parameters, while ferritin (FRT) with the ~11 fold increase showed the most change. Significant reduction in HEPC and increase in ERFE levels were detected in patients as compared to the control group, while no direct correlation was identified with the other measured ISPs. Receiver operating characteristic (ROC) analysis showed that the z-score of the composite of ERFE+FRT has a full diagnostic ability for β-TM. In conclusion, our finding indicated the correlation between different ISPs, FRT as the leading predictor of iron overload and tow main iron regulatory hormones.

Pearl millet is an important food crop in the arid and semi-arid tropical regions of Africa and Asia. These regions are home to millions of poor smallholder’s households living in harsh agro ecology and reported higher prevalence of malnutrition. Such poor households have few options in terms of food crops, besides the limited markets. Indeed, pearl millet is one of the food crops they continue to grow for their food and nutritional security. Pearl millet is important sources of dietary carbohydrates, energy, protein, and important minerals such as calcium, iron and zinc. Considering inherent high nutritional values and climate resilient nature (drought and heat), demand for pearl millet as food, beside valued for its Stover as a source of livestock fodder, is projected to grow strongly in Asia (India) and Africa (West and Central Africa). Iron (cause anemia) and zinc (cause stunting) deficiencies are widespread and serious public health problems worldwide, including India and Africa. Biofortification is a cost-effective and sustainable agricultural strategy to address this problem. Research on pearl millet has shown that large genetic variability (30-140 mg/kg Fe and 20-90 mg/kg Zn) available in this crop can be effectively utilized to develop high-yielding cultivars with high iron and zinc densities. Both Open –pollinated varieties (Dhanshakti and Chakti) and hybrids (ICMH 1202, ICMH 1203 and ICMH 1301) of pearl millet with high grain yield (>3.5 tons/ha in hybrids) and high levels of iron (70-75 mg/kg) and zinc (35-40 mg/kg) densities have been developed and released. Currently, India growing >70,000 ha of biofortified pearl millet, besides more pipeline hybrids and varieties are under various stage of testing at the national (India) and international (west Africa) trials for possible release. Genomic tools will be an integral part of breeding program particularly for nutritional traits to use diagnostic markers and genomic selection. Clinical studies showed that 200g grains from biofortified cultivar would provide bioavailable Fe to meet full recommended daily allowance (RDA) in children, adult men and 80% of the RDA in women. Till today, no markets to promote biofortified cultivars/grains/products as no incentive price and such products aims to address food and nutritional security challenges simultaneously. The demand is likely to increase only after investment and integration into modern public distribution system, nutritional intervention schemes, private seed and food companies with strong mainstreaming nutritional policies. In the non-traditional regions, this will contribute to livestock and poultry feed industry as spill-over benefits to improve nutrition.

Nuclear receptor coactivator 4 (NCOA4) is a selective cargo receptor that mediates the autophagic degradation of ferritin (“ferritinophagy”), the cytosolic iron storage complex. NCOA4-mediated ferritinophagy maintains intracellular iron homeostasis by facilitating ferritin iron storage or release according to demand. Ferritinophagy is involved in iron-dependent physiological processes such as erythropoiesis, where NCOA4 mediates ferritin iron release for mitochondrial heme synthesis. Recently, ferritinophagy has been shown to regulate ferroptosis, a newly described form of iron-dependent cell death mediated by excess lipid peroxidation. Dysregulation of iron metabolism and ferroptosis have been described in neurodegeneration, cancer, and infection, but little is known about the role of ferritinophagy in the pathogenesis of these diseases. Here, we will review the biochemical regulation of NCOA4, its contribution to physiological processes and its role in disease. Finally, we will discuss the potential of activating or inhibiting ferritinophagy and ferroptosis for therapeutic purposes.

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

Semiconductors play a very important role in modern society. The improvement in performance of semiconductors is what has enabled the world to grow at such a fast pace. For decades scaling has been done through Moore’s law i.e performance improvements have been obtained due to transistor scaling where the number of transistors per unit area increase is what has contributed to the increase in performance. However, with transistor scaling reaching its limitations we need to find alternate methods to enhance silicon design to suit the computational need of modern society. To address this problem we will be looking into a few methods that enable performance scaling with a focus on analysing the most popular implementation of each in the industry.