Forensic detection of non-volatile nitro explosives poses a tough analytical challenge. A colorimetric sensor comprising ultrasonically prepared silica-dye microspheres was developed for sensitive gas detection of cyclohexanone, a volatile marker of explosives 1,3,5-trinitro-1,3,5-triazinane (RDX) and 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX). The silica-dye composites were synthesized from the hydrolysis of ultrasonically sprayed organosiloxanes under mildly heating conditions (150 ^oC), which yields microspherical, nanoporous structures with high surface area (~300 m²/g) for gas exposure. The sensor inks were deposited on cellulose paper and gave sensitive colorimetric responses to trace amount of cyclohexanone vapors even at sub-ppm levels, with the detection limit down to ~150 ppb. The sensor showed high chemical specificity towards cyclohexanone against humidity and other classes of common solvents, including ethanol, acetonitrile, ether, ethyl acetate, and ammonia. Paper-based colorimetric sensors with hierarchical nanostructures could represent an alternative sensing materials for practical applications in the detection of explosives.

Oil agents produced from degreasing treatment of synthetic fibers are typical pollutants in printing and dyeing wastewater, which may cause large-scale environmental pollution without proper treatment. How to purify oily dye wastewater with low cost is a key problem at present. In this study, the biochar microspheres with oil removal ability were prepared deriving from waste bamboo chips using hydrothermal method. The structure of biochar microsphere was regulated by the activation and modification processes. The biochar microspheres were characterized and their adsorption behaviors for oily dye wastewater were explored. The results showed that the adsorption efficiency of biochar microspheres for oily dye wastewater (DTY) was improved significantly after the secondary pyrolysis and lauric acid grafting reaction. The maximum COD removal quantity of biochar microspheres for DTY was 889 mg/g with removal rate of 86.06% in 30 min. Besides, the kinetics showed that the chemisorption was the main adsorption manner. The application of biochar microspheres can decrease the costs of oily wastewater treatment and avoid environmental pollution.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

Novel far-red-sensitive symmetric squaraine (SQ) dyes with terminal alkyl-chain modifications were designed, synthesized and characterized aiming towards imparting multifunctionalities such as photosensitization, dye aggregation prevention and source of electrolyte components. The dye sensitizers SQ-77 and SQ-80 with the alkyl chain terminal modifications consisting of iodine and 1-methylimidazolium iodide, respectively, were designed and synthesized as new dye sensitizers for DSSCs based on the symmetric SQ-5 without any terminal modification used as reference. Upon adsorption on the mesoporous TiO2 surface, The SQ-77 depicted an enhanced dye loading and dye aggregation. On the other hand, SQ-80 demonstrated reduced dye aggregation and stronger binding on the TiO2 surface leading to enhanced durability of DSSCs. Apart from the most common photosensitization behaviour, the newly designed dye demonstrated multifunctionality such as aggregation prevention and electrolyte functionality utilizing iodine-based redox electrolyte in the presence and absence of I2 and LiI additives. In the absence of LiI and I2, a mixture of SQ-77 and SQ-80 demonstrated a photoconversion efficiency of 1.54 % under simulated solar irradiation, which was about 6 times higher as compared to reference dye SQ-5 (0.24 %) having no alkyl chai terminal modification.

The dye effluent is usually difficult to be degraded by conventional wastewater treatment in leather industry. In order to develop efficient and cost-effective treatment methods, we evaluate the effect of white-rot fungus immobilization for dye decolorisation in this paper. The Phanerochaete chrysosporium BKM-F-1767 was used for immobilization. This research found that the white-rot fungus immobilization had an obviously decolorisation effect in dye wastewater treatment, and plant carriers such as sorghum stalk and corn cob were helpful to the growth of Phanerochaete chrysosporium in white-rot fungus immobilization. Due to the stability and recyclability, the white-rot fungus co-immobilization was considered as the most suitable treatment for decolorisation of dye effluent which enjoyed the advantages of both adsorption immobilization and entrapment immobilization. Furthermore, the dye decolorisation evaluation was carried out to find the most suitable carrier for co-immobilization, and it found that sorghum stalk - calcium-alginate gel spherical particle (SS-CGPB) has better decolorisation effect than corn cobs - calcium-alginate gel spherical particle (CC-CGPB), and the dye decolorisation rate was 86.77%. After 5 cycles, the dye decolorisation rate was 85.87% which indicated the SS-CGPB preserved functional integrity successfully. By further analyzing the biodegradation process with white-rot fungus immobilization, the intermediate products were observed and the degradation pathway of acid golden yellow dye molecular was proposed. The results showed that the C-N single bonds attached to the central benzene in the dye molecule were attacked and destroyed in white-rot fungus co-immobilization treatment, thus the structure of dye molecule could be successfully degraded into small molecules which would be more easily treated by conventional treatment methods. Therefore, the white rot fungus co-immobilization might be appropriate for pre-treatment as an important biotechnology for the advanced treatment of dye effluent.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Dyes, as indigo carmine have become indispensable to modern life being widely used in food, textile, pharmaceutical, medicine and cosmetic industries. Although indigo carmine is considered toxic and presents many adverse effects, it is heavily used in the food industry because the blue pigment is difficult to obtain from natural sources and is one of the most used dyes in the textile industry, especially for dyeing denim. Also, indigo carmine is one of the dyes used in medicine as diagnostic agent because it has impressive applicability in terms of diagnostic methods and surgical procedures. In the literature it is reported that indigo carmine is toxic for humans and can cause various pathologies, such as hypertension, hypotension, skin irritations, corneal and conjunctival disorders or gastrointestinal disorders. In this review, we discuss the structure and properties of indigo carmine, its use in various industries and medicine, the adverse effects of its ingestion, injection or skin contact, the effects on environmental pollution and its toxicity testing.

Chemical flooding is one of the effective methods to recover large volumes of oil from sandstone formations after primary depletion. However, silica dissolution often occurs during Alkaline-Surfactant-Polymer (ASP) flooding, affecting the petro-physical properties of the formation. To address this issue, samples from Berea sandstone formations were treated with various brine solutions, through static tube tests and core flooding experiments. Analytical tests such as DR/2800 spectrophotometer and scanning electron microscope were used to evaluate the silica solubility and the alteration in mineral content. The results indicated that the silicate contents decreased after the saturation due to silica solubility in the solution. Increasing brine salinity to 40,000ppm and introducing Magnesium and Calcium ions to the solution, reduces the silicate contents by 5.03 % and 7.32 %. Moreover, saturating the samples with ASP solution, further reduced the silicate contents by 14.86 %. This reduction is associated with a relative increase in silica solubility and pH of the solution. Silica dissolution affects the pore microstructure, which resulted in increasing the porosity and pore volume after the core flooding. The injection of the ASP solution increased the porosity by 5.83%, thus the pore volume increased from 17.72 to 18.76cc. This is associated with the high silica solubility and the increase of solution pH in the ASP solution. The permeability of the samples generally reduced after the core flooding, due to the silica solubility. However, injecting the ASP solution, resulted in a major reduction of the permeability by more than 75%. These changes in the petro-physical properties can lead to severe formation damage, and affect hydrocarbon production. This study assists in understanding the impact of silica dissolution during ASP treatment and addresses the factors involved. Efficient utilization of chemical flooding can help mitigating silicate scaling within the formation, and extend field productivity.

After a survey on polymer plasticization theories and conventional criteria to evaluate polymer-plasticizer compatibility through the solubility parameter, an attempt to create a polymer-plasticizers polarity scale through solvatochromic dyes has been made. Since the Reichardt’s ET(30) dye is insoluble in rubber hydrocarbon polymers like polyisoprene, polybutadiene and styrene-butadiene copolymers and is not also useful for the evaluation of the hydrocarbons and ester plasticizers, the Nile Red solvatochromic dye was instead used extensively and successfully for this class of compounds. A total of 53 different compounds were evaluated with the Nile Red dye and wherever possible also with the ET(33) Reichardt’s dye. A very good correlation was then found between the Nile Red scale E(NR) and the Reichardt’s ET(30) scale for this class of compounds focusing on diene rubbers and their typical hydrocarbons and new esters plasticizers. Furthermore, the E(NR) scale shows also a reasonable correlation with the total solubility parameter calculated according to the Van Krevelen method. Based on the above results, some conclusion was made about the compatibility between the diene rubbers and the conventional plasticizers as well as some new and green plasticizer proposed for the rubber compounds.

Fish oil rich in docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA), vitamin D₃ and natural astaxanthin sustainably extracted from anchovy fillet leftovers using biobased limonene only, can be conveniently stabilized by adsorption on periodic mesoporous silicas. The simplicity of the process, the high load of entrapped fish oil, and the biocompatible nature of silica support numerous forthcoming applications of this new class of “Omeg@Silica” materials.

In this work, a high throughput nanozymatic method was developed for green nanozyme-mediated biodegradation of organic dyes in real water media. The nanozymes were synthesized and characterized for their size and morphology by TEM and DLS analysis. The nanozymatic properties of the as-prepared nanomaterials were evaluated by standard enzyme activity assay, revealing high peroxidase-like performances for the as-prepared nanozymes. Therefore, for exploring more precise, the kinetics behavior of the as-prepared nanozymes was evaluated by the standard Lineweaver-Burk method, revealing a V_max as high as 0.263 µM sec^-1 and a K_m as low as 0.03 mM, revealing high catalytic efficiency and affinity of the as-prepared nanozymes. Hence, the as-prepared nanozymes were utilized for organic dye degradation in real water media using methylene blue as a model organic dye. The effective factors on the dye degradation including pH, ionic strength, degradation time, nanozyme amount, etc. were optimized by the one-factor-at-a-time optimization method. At optimal experimental conditions, the as-prepared nanozymes can degrade about 99.0% of the organic dye within a degradation time as low as 7 min. The developed method was finally employed for the nanozyme-mediated degradation of methylene blue from real water media such as pool, mineral, river, and tap water samples. The results of this study revealed an excellent biodegradation yield of over 94.3%-99.0% for the different real samples, proving the suitability of the developed method for dye degradation in real water media.

The research aims to resolve water pollution generated by dye wastewater. In this paper, the aminated sodium lignosulfonate (AELS) was prepared through the Mannich reaction, and the synthesis conditions were optimized using orthogonal experiments to determine the best amination conditions. The successful preparation of AELS was demonstrated through the use of FT-IR, XRD, TG, SEM and XPS characterization techniques. Then, the adsorption capacity of Methyl blue (MB) by AELS was compared in a range of different circumstances, like pH, adsorbent dose, initial concentration, time, and temperature. Additionally, the kinetics, isotherms, and thermodynamic properties of the AELS adsorption for MB were studied and discussed. The results indicated that the fitting results were consistent with the pseudo-second-order kinetic model and Langmuir isotherm model, in accordance with the mechanism of single-molecular-layer chemisorption. And the adsorption of MB by AELS was a spontaneous and endothermic process. Upon completion of five adsorption experiments, the adsorption capacity of MB by AELS was determined to be 107.95 mg g-1, which was 5.3% lower than the first experiment. This research promotes the effective use of natural resources and allows for the sustainable use of lignin and the advancement of new applications for it.

In the East, it has already become a tradition to prepare dry powdered seasonings from the fruits of the sumac plant (Rhus coriaria L.). In this work, we tested their processing by extraction. Sumac was collected in mid-September in a mountain forest near the village of Gezik (Guba, Azerbaijan). Before extraction, it was first dehydrated in a drying cabinet SH-DO-149 FG (Southern Bark) to an air-dry state; then crushed in a Tube Mill control mill (Germany) into pieces of 1-3 mm in size. One- and two-stage maceration extraction was tested together with water or acidified water at temperatures from 20 to 80 °C. Evaporation of primary extracts was carried out in a rotary evaporator Lab Rot 2 L (China). The concentration of coloring substances in the extract (in units of optical density) was used as an output parameter. It was found that the use of two-stage extraction and acidified water with a concentration of citric acid 0.3 g/cm³ contributes to the extraction of the maximum amount of coloring substances and increases the transparency of the resulting extracts, which allows the extracted extracts to be concentrated directly to obtain a new type of natural food dye. The involvement of sumac fruits in industrial processing will increase the need for these medicinal fruits, and this, in turn, will serve as an incentive for the introduction of this medicinal plant into culture.

The present study analyzed the efficiency of a naturally derived fenugreek powder for removal of Congo red dye from the aqueous solution. The flocculation Studies on Congo Red (CR) a hazardous, textile dye onto Fenugreek Powder and its adsorption was analyzed. Fenugreek Powder is Eco-friendly, biodegradable and locally available in the market. The dye adsorption process was performed in different batches at varying pH, dye concentration, adsorbent concentration and contact time to get the best results. The result showed that the maximum removal of dye was 42.4% with 10mg/l of Fenugreek powder at pH 4.

As the major greenhouse gas, CO2 gas emission has been noticeably increased over the past decades resulting in global warming and climate change. As a result, it is imperative to reduce the excess CO2 in the atmosphere to hold “the increase in the global average temperature to well below 2°C (ideally 1.5°C) above pre-industrial levels set by the Paris Agreement on climate change. Among many ways, CO2 capture technology is considered as the most promising technology among the available technologies. Porous materials such as carbons, silica, zeolites, hollow fibers, and alumina are widely used as CO2 sorbents. However, among the available porous sloid sorbents, porous silica-based materials grabbed a significant attention due to their unique properties including high surface area, pore volume, good thermal and mechanical stability, and low cost. Therefore, development of porous silica materials as a promising CO2 absorbent is a continuously expanding research area in the current moment. Herein, we aim to visualize a full picture of the porous silica-based materials for CO2 capture. This review presents a comprehensive study of existing CO2 capture techniques and highlights the recent progress of different porous silica materials and synthesis processes. CO2 adsorption capacities of unmodified porous silica materials are less effective as compared with functionalized silica materials. Various research activities have been reported about functionalization of pours silica using amine groups. Therefore, in this review, different synthesis routes of amine-functionalized porous silica materials, CO2 adsorption capacities, gas selectivity and reusability were discussed. Moreover, the research challenges associated with the porous silica materials and future research directions are summarized.

The composites of heteropolyacids (H3PW12, H3PMo12) incorporated into amine-functionalized silica materials, were used for the first time as heterogeneous catalysts in the valorisation of glycerol (a large waste from biodiesel industry) by acetalization reaction with acetone. The polyoxotungstate catalyst H3PW12@AptesSBA-15 presented higher catalytic efficiency than the phosphomolybdate, with 97% of conversion with 97% of solketal selectivity, after 60 min at 25 °C, or 91% of glycerol conversion and the same selectivity, after 5 min, performing the reaction at 60 ºC. A relation of catalytic performance and acidity of the catalyst is here presented. Furthermore, the stability of the solid catalyst was investigated and discussed.

Mineral surfaces have been demonstrated to play a central role in prebiotic reaction, which are supposed to be at the basis of the origin of life. Among the various molecules proposed as precursors for these reactions, one of the most interesting is formamide. Formamide has been shown to be a pluripotent molecule, generating a wide distribution of relevant pre-biotic products. In particular, the outcomes of its reactivity are strongly related to the presence of mineral phases, acting as catalysts toward specific reaction pathways. Even if the mineral-products relationship has been deeply studied for a large pool of materials, the fundamental description of the formamide reactivity over the mineral surface at a microscopic level is missing in the literature. In particular, a key step of formamide chemistry at surfaces is its adsorption on the available interaction sites. This report aims to investigate the adsorption of formamide over a well-defined amorphous silica, chosen as model mineral surface. An experimental IR investigation of formamide adsorption has been carried out and its outcomes have been interpreted on the basis of first principles simulation of the process adopting a realistic model of the amorphous silica.

Disposing pollutants into water sources has posed risks to human health and the environment, and biosorption has emerged as an eco-friendly, cost-effective, and green alternative for wastewater treatment. This work shows banana peel powder (BPP) biosorbents for efficient sorption of methylene blue (MB), atrazine, and glyphosate pollutants. The biosorbent highlights several surface chemical functional groups and morphology containing agglomerated microsized particles and microporous structures. BPP showed 66% elimination of MB in 60 min, with an adsorption capacity (qe) of ~33 mg g-1, where a combination of film diffusion and chemisorption governed the sorption process. Besides, the biosorbent removed 91% and 97% of atrazine and glyphosate pesticides after 120 min, with qe of 3.26 and 3.02 mg g-1, respectively. The glyphosate and atrazine uptake best followed the Elovich and pseudo-first-order kinetic, respectively, revealing different sorption mechanisms. Our results suggest that BPP are low-cost biomaterials for green and environmentally friendly wastewater treatment.

Development of biomarkers of analytes with interest in clinic is an important field of study. In this work, we synthesized and analyzed the new fluorescent acetate-biomarker, Iso-PG. The mechanism of detection is the acetate buffer mediated proton transfer reaction. The rate constants involved were obtained, and we measured the change in the fluorescence lifetime produced as a consequence of the presence of acetate in the medium. Finally, we checked its potential use as acetate biomarker in synthetic serum

Nowadays, the study of preparing silica/rubber composites, which can be used in “green tire”, in energy saving method is fast-growing. In our work, silica modified by using alcohol polyoxyethylene ether (AEO) and 3-Mercaptopropyltriethoxysilane (K-MEPTS) together were investigated. Thermal gravimetric analyzer (TGA) result indicated that both AEO and K-MEPTS could be grafted on the silica surface. Raman spectroscopy confirmed that the AEO could generate a certain steric hindrance for the mercaptopropyl group on K-MEPTS. Silica modified by using AEO and K-MEPTS together can be completely co-coagulated with the rubber in preparing silica/natural rubber (NR) composites by latex compounding method. AEO can form a physical interface between silica and rubber; meanwhile, K-MEPTS can form a chemical interface between silica and rubber. The effects of chemical and physical interface between silica and rubber on dynamic and mechanical performances of silica/NR composites were also given in this research. A proper combination of physical and chemical interface between silica and NR can improve performances of silica/NR composites.

In this work, we report the engineering of a sub-70 nm nanocomposite of ZnO/Zn2TiO4 using a low-temperature solution-phase method. Titanium isopropoxide and zinc acetate were used as precursors, and isopropyl alcohol and water were used as solvents. The investigation focused on the growth of nanocomposites by varying the concentrations of precursors and surfactants, as well as their efficiency within different pH ranges. All three ZnO/Zn2TiO4 nanocomposites consist of hexagonal wurtzite ZnO and Zn2TiO4 structures in the three nanocomposites. The crystallite size in three ZnO/Zn2TiO4 nanocomposites, with a hexagonal wurtzite ZnO structure, were measured to be 62.67, 40.34, and 39.50 nm. The crystallite size values in three ZnO/Zn2TiO4 nanocomposites were 26.15 nm, 25.36 nm, and 21.24 nm, respectively, with Zn2TiO4. Morphological observations, conducted using FESEM, reveal the formation of three ZnO/Zn2TiO4 nanocomposites across the entire sample. These nanocomposites resemble dispersed cotton packets, with sizes ranging from 18 to 350 nm. Peaks in the range of 610-1250cm-1 are attributed to Ti-O bond formation and peak located at 1350-1450 cm-1 are attributed to Zn-O bond formation. Also, EDX spectrum reveals peaks for various sample components such as Ti, O and Zn. UV spectrums confirmed the formation of three nanocomposite of ZnO/Zn2TiO4 as showing two peaks for each sample. Photocatalytic investigation carried out by analyzing the UV-Visible absorption spectra of methylene blue dye on the surface of ZnO/Zn2TiO4 nanocomposites, dye degradation at various irradiation time intervals, dye degradation at varied catalyst concentrations and the influence of pH on dye-degradation. Furthermore, the said nanocomposites were used to degrade environmental pollutant (Methylene blue dye). Different sets of experiments were conducted under ambient conditions which show an excellent photo catalytic degradation efficiency.

Water pollution is regarded as a dangerous problem that needs to be resolved right away. This is largely due to the positive correlation between the increase in global population and waste production, especially food waste. Hydrogel beads based on sodium alginate (Alg) and pomegranate fruit peels (PP) were developed for the adsorption of Safranin O dye (SO) in aqueous solutions. The obtained Alg-PP beads were widely characterized. The effects of the contact time (0-180 min) and initial concentration (10-300 mg/l), the initial pH (2-10), the adsorbent dosage (1-40 g/l) and the temperature (293-333 K) were investigated through batch tests. The data proved that the adsorption kinetics of SO reached equilibrium within 30 min and up to 180 min. The adsorption data of SO onto synthesized beads follow the pseudo second-order model. The experimental data fitted very well to both Freundlich and Langmuir models. The maximum adsorption capacity of Alg-PP could reach 8.99 mg/g at 293 K. Calculation of Gibbs free energy and enthalpy indicated that adsorption of SO onto Alg-PP is spontaneous and endothermic. Finally, analysis of diffusion and mass transport phenomena were presented. The reported results revealed that the Alg-PP beads could be used as a novel natural adsorbent for the removal of cationic dye pollutants from aqueous environments.

A novel fluorescent probe (C460@Tb-MOFs) was designed and synthesized through encapsulating the fluorescent dye 7-diethylamino-4-methyl coumarin into terbium-based metal-organic framework by a simple ultrasonic impregnation method. It is impressive that this dye-modified metal-organic framework can specifically detect styrene and temperature upon luminescence quenching. The sensing platform of this material exhibit great selectivity, fast response and good cyclability toward styrene detection. It is worth mentioning that the sensing process undergoes a distinct color change from blue to colourless, providing conditions for accurate visual detection of styrene liquid and gas. The significant fluorescence quenching mechanism of styrene toward C460@Tb-MOFs is explored in detail. Moreover, the dye-modified metal-organic framework can also achieve temperature sensing from 298 to 498 K with high relative sensitivity at 498 K. The preparation of functionalized MOFs composites by fluorescent dyes provides an effective strategy for the construction of sensors for multifunctional applications.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

Antimicrobial peptides (AMPs) have emerged as a promising solution to tackle bacterial infections and combat antibiotic resistance. However, their clinical application has been hindered by their vulnerability to protease degradation and toxicity towards mammalian cells. To overcome these challenges, our study aims to develop a method to enhance the stability and safety of AMPs, applicable to effective drug-device combination products. KR12 antimicrobial peptide was chosen and in order to further enhance its delivery and efficacy, HIV TAT protein-derived cell-penetrating peptide (CPP) was fused to form CPP-KR12. A new product, CPP-KR12@Si, was developed by forming silica nanoparticles with self-entrapped CPP-KR12 peptide using the biomimetic silica precipitability due to its cationic nature. Peptide delivery from CPP-KR12@Si to bacteria and cells was delivered at a slightly delayed rate with improved stability against trypsin treatment and a reduction in cytotoxicity over CPP-KR12. Finally, the antimicrobial potential of CPP-KR12@Si/bone graft substitute (BGS) combination product was demonstrated, which is coated with CPP-KR12 in the form of nanoparticles on the surface of BGS. Self-entrapped AMP in silica nanoparticles is a safe and effective AMP delivery method that will be useful for developing a drug/device combination product for tissue regeneration.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

Water pollution, driven largely by the discharge of organic dyes from various industrial processes, presents a grave environmental threat. This study delves into the promise of an innovative adsorptive composite material composed of chitosan and activated charcoal, offering a sustainable and efficient solution for removing methylene blue (MB) dye from water sources. Our comprehensive investigation encompasses the synthesis, characterization, and adsorption capabilities of this composite material, revealing its remarkable physicochemical attributes and its substantial capacity to adsorb MB dye. These findings establish it as a compelling candidate for water treatment applications. The assessment of adsorbent dosage shows a direct correlation between higher dosages and enhanced MB dye removal, with an optimal dosage determined at 0.4 g/25 mL. Furthermore, pH-dependent studies demonstrate exceptional performance at lower pH levels, achieving an impressive 95% removal rate at pH 3 after 240 minutes of contact time. The composite exhibits consistent high removal percentages across a wide range of MB dye concentrations, showcasing its adaptability. In terms of reaction time, the composite achieves peak adsorption capacity within the initial 360 minutes and maintains a stable equilibrium, sustaining an impressive 99% removal efficiency thereafter. This study underscores the eco-friendliness and cost-effectiveness of the composite material, emphasizing its potential to address water pollution challenges and promote sustainable water resource management. Overall, this research yields valuable insights into a practical approach for mitigating the adverse impact of organic dyes on aquatic ecosystems and public health.

The presence of dyes in wastewater effluents made from the textile industry is a major environmental problem due to their complex structure and poor biodegradability. In this study, a cationic lignin polymer was synthesized via the free radical polymerization of lignin with [2- (methacryloyloxy) ethyl] trimethylammonium chloride (METAC) and used to remove anionic azo-dyes (reactive black 5, RB5, and reactive orange 16, RO16) from simulated wastewater. The effects of pH, salt and concentration of dyes, well as the charge density and molecular weight of lignin-METAC polymer on dye removal were examined. Results demonstrated that lignin-METAC was an effective flocculant for the removal of dye via charge neutralization and bridging mechanisms. The dye removal efficiency of lignin-METAC polymer was independent of pH. The dosage of the lignin polymer required for reaching the maximum removal had a linear relationship with the dye concentration. The presence of inorganic salts including NaCl, NaNO3 and Na2SO4 had marginal effect on the dye removal. Under the optimized conditions, greater than 98 % of RB5 and 94 % of RO16 were removed at lignin-METAC concentrations of 120 mg/L and 105 mg/L in the dye solutions, respectively.

The focus of this research is to improve the performance of dye-sensitized solar cells (DSSC) through the adoption of high-quality FTO thin films and incorporation of graphene with DSSC photoanode to enhance its electrical transport. In this research, nanostructured FTO films were first grown with homemade Streaming Process for Electroless and Electrochemical Deposition technology (SPEED) using Tin (II) chloride dihydrate and ammonium fluoride and other chemical formulations. The FTO structural property was measured by X-ray diffraction (XRD); the films’ optical property was determined with transmittance spectra to curve over the wavelength range of 200-1000 nm measured with a spectrophotometer while scanning electron microscope (SEM) was used to determine the morphological properties of the samples. The electrical transport was evaluated by Hall Effect measurements at room temperature with a four-point probe. The FTO samples with the best structural, optical and electrical properties were employed as electrodes and counter electrodes of DSSC along with titanium dioxide. Thus, effect of graphene on the efficiency of DSSC was investigated. It was shown that a graphene-based DSSC showed an efficiency of 7.98% which is slightly higher than that of DSSC prototype without graphene (6.02%). The higher efficiency obtained with graphene can be credited to the ultrahigh surface area and thermal conductivity of graphene which tend to enhance the charge mobility and photovoltaic performance of DSSC. More research is however required to determine the exact amount of graphene that could achieve optimal DSSC performance. Further studies will also offer an adequate clarification for starting point of the better incorporation of graphene in DSSCs.

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

Major progress in the field of regenerative medicine are expected from the design of artificial scaffolds that mimic both the structural and functional properties of the ECM. The bionanocomposites approach is particularly well fitted to meet this challenge as it can combine ECM-based matrices and colloidal carriers of biological cues that regulate cell behavior. Here we have prepared bionanocomposites under high magnetic field from Tilapia fish scale collagen and multifunctional silica nanoparticles (SiNPs). We show that scaffolding cues (collagen), multiple display of signaling peptides (SiNPs) and control over the global structuration (magnetic field) can be combined into a unique bionanocomposite for the engineering of biomaterials with improved cell performances.

Heavy metals are non-biodegradable and have a high toxicity effect to living things which makes their presence in the environment extremely dangerous. The method of handling heavy metals waste by photocatalysis techniques using TiO2/SiO2 composite showed a good performance in reducing harmful pollutants. In this study, SiO2 from Bengkulu beach sand was used as a support material for TiO2 photocatalyst to reduce Cr(VI) and Pb(II) concentrations. SiO2 was obtained through leaching techniques using NaOH as a solvent. The TiO2/SiO2 composite photocatalyst were synthesized using a solvothermal method at 130 °C and then characterized using XRD, FTIR, SEM and PSA. Based on the XRD diffractogram, the synthesized TiO2 showed the anatase structure while the SiO2 showed the amorphous structure. Ti-O-Si bond is defined in the IR spectra, which indicates that the relationship between TiO2 and SiO2 is a chemical interaction. The results of SEM and PSA characterizations show agglomerated spherical (round) particles with a mean particle size of 616.9 nm. The TiO2/SiO2 composite of 7:1 ratio showed the highest photocatalytic activity after 180 minutes of UV irradiation, with a concentration-decrease percentage of 93.77% and 93.55% for for Cr(VI) and Pb(II), respectively.

The present contribution is focused on the relation preparation – structure – optical properties of hybrid silica and zirconia powders containing Eu(III) complexes: [Eu(ntac)₃][pphendcn] and [Eu(phen)₂](NO₃)₃. Methods for functionalization of silica and zirconia microparticles, based on adsorption of 1,10-phenantroline and [Eu(ntac)₃][pphendcn], and doping with [Eu(phen)₂](NO₃)₃ nanoparticles are proposed to obtain of red emitting hybrid composites with quantum efficiency 20 – 50 %. The optical properties of rare earth ions incorporated in silica and zirconia composites are used to explore the site symmetry (D₂, C_2v or lower) of the Eu³⁺ optical centers in the hybrid composites. Quantum yields of the investigated sol-gel micropowders and quantification of their optical spectra are presented.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

A magnetite (CDC@Fe3O4) heterogeneous photocatalyst was synthesized via treated and modified cotton in two steps. The designed nanocomposites were characterized by FTIR, TGA, XRD, SEM, and VSM analyses. The Fenton-photocatalytic decomposition efficiency of the synthesized magnetic catalyst was evaluated under visible sunlight using Methyl Orange (MO) as a model organic pollutant. The impacts of several degradation parameters, including the light source, catalyst load, irradiation temperature, oxidant dose, and pH of the dye aqueous solution and its corresponding concentration on the Fenton photodegradation performance, were methodically investigated. (CDC@Fe3O4) heterogeneous catalyst showed a remarkable MO removal rate of 97.9% at 10 min under visible-light irradiation. (CDC@Fe3O4) nanomaterials were also used in a heterogeneous catalytic optimized protocol for a multicomponent reaction procedure to obtain nine tetra-substituted imidazole derivatives. The green protocol afforded imidazole derivatives in 30 min with good yields (91-97%) at room temperature and under ultrasound irradiation. Generally, a synthesized recyclable heterogeneous nano-catalyst is a good example and is suitable for wastewater treatment and organic synthesis.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

A Invasive emerging pollutants from wastewater effluent discharge, such as dyes, pesticides, etc., pose a serious threat to the ecosystem. Advanced oxidation processes (AOPs) under visible light irradiation have emerged as a promising technology to overcome toxic and recalcitrant organic compounds. In this work, the impact of operational factors, including the concentration of Fe3+ or Fe2+, [H2O2], the molar ratio (Oxalate/ Fe3+ or Fe2+), and the initial pH, was studied to obtain high efficiency in the degradation and mineralization of such a food dye to reduce their pollution. The study deals with the comparison of the efficiency of UV, LED, and sunlight irradiation on the photocatalytic degradation of the dye using Fe3+/Lig and Fe2+/Lig complexes. The results showed that sunlight irradiation gave a very rapid kinetic and higher degradation efficiency of over 70%. The optimized conditions for the maximum elimination of the dye with a photocatalytic degradation efficiency (98%) and a mineralization rate of 96% were obtained with the Fe3+/Lig complex, based on the Box Benhken surface design analysis. In the presence of H2O2, the degradation reached an equilibrium stage after 15 min (97.57%) for the Fe(III)/Lig system. Moreover, the inhibition effect of inorganic ions on the photo-Fenton performance of Fe3+/Lig and Fe2+/Lig was studied. The study suggests that the use of nanocrystals of hematite as a Fenton reagent for treating textile effluents needs further investigation. The results showed that the proposed models were well-suited to batch treatment under sunlight. This study not only proposes a Fe3+/Lig and Fe2+/Lig system for the elimination of a food dye without adjusting the pH of the medium, but it also provides insight into the best source of light irradiation for the photocatalytic degradation process.

This study demonstrates the viability of an orange peel-based adsorbent as sustainable alternative for the elimination of the disperse dye C.I. Disperse Blue 56 present in waste waters of the dyeing industry of textiles. The effectiveness of the adsorbent is evaluated at different pH values and the adsorption capacity is determined by systematically comparing orange peel and the final adsorbent chemically treated. Results reveal an spontaneous coagulation-flocculation phenomenon of the dispersed dye at low pH values which represents a sustainable way for the recovery and possible re-use of the dye, together with the industrial valorisation of a wasting product as is orange peel.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

Two ligands, 1, 3-bis(4-carboxyphenyl)imidazolium chloride and 4, 4՛-bipyridine, were employed to prepare nickel and zinc azolium based MOFs, 1 and 2 by the mixed ligand solvothermal approach. The positively charged azolium moieties in the imidazolium linker resulted in a charged environment in the as-synthesized frameworks. As a result, 1 and 2 demonstrated preferential adsorption of CO2 over methane molecules in the gas phase adsorption due to the higher quadruple moment of CO2, which interacts more with the positively charged frameworks. Besides, in aqueous media, 1 and 2 exhibited incredible adsorption efficiency for anionic dyes. In the following, MOF 1 was metallated at the carbene site of the azolium linker to generate the novel heterogeneous catalyst 1-Pd, which was successfully applied for Sonogashira and Suzuki-Miyaura coupling reactions without losing its activity after three cycles.

Although laccase has been recognized as a wonder molecule, and green enzyme, the use of low yielding fungal strains, poor production, purification, and low enzyme kinetics have hampered its larger-scale applications. Hence the present research was aimed to select high yielding fungal strains and to optimize the production, purification, and kinetics of laccase of Aspergillus sp. HB_RZ4. Aspergillus sp. HB_RZ4 produced a copious amount of laccase on under meso-acidophillic shaking conditions in a medium containing glucose and yeast extract. A 25 µM of CuSO4 enhanced the enzyme yield. The enzyme was best purified on Sephadex G-100 column. Purified enzyme resembled with the laccase of A. flavus. Kinetics of purified enzyme revealed the high substrate specificity and good velocity of reaction with ABTS as substrate. The enzyme was stable over a wide range of pH and temperature. The peptide structure of the purified enzyme resembled with the laccase of A. kawachii IFO 4308. The fungus decolorized various dyes independent of the requirement of a laccase mediator system (LMS). Aspergillus sp. HB_RZ4 came out as a potent natural producer of laccase, it decolorized the dyes even in absence of LMS and thus can be used for bioremediation.

Chloroquine was among the first of several effective drug treatments against malaria until the onset of chloroquine resistance. In light of diminished clinical efficacy of chloroquine as an antimalarial therapeutic, there is potential in efforts to adapt chloroquine for other clinical applications, such as in combination therapies and in diagnostics. In this context, we designed and synthesized a novel asymmetrical squaraine dye coupled with chloroquine (SQR1-CQ). In this study, SQR1-CQ was used to label live Plasmodium falciparum (P. falciparum) parasite cultures of varying sensitivities towards chloroquine. SQR1-CQ positively stained ring, mature trophozoite and schizont stages of both chloroquine–sensitive and chloroquine–resistant P. falciparum strains. In addition, SQR1-CQ exhibited significantly higher fluorescence, when compared to a chloroquine-BODIPY (borondipyrromethene) conjugate. We also achieved successful SQR1-CQ labelling of P. falciparum directly on thin blood smear preparations. Drug efficacy experiments measuring half-maximal inhibitory concentration (IC50) showed lower concentration of effective inhibition against resistant strain K1 by SQR1-CQ compared to conventional chloroquine. Taken together, the versatile and highly fluorescent labelling capability of SQR1-CQ and promising preliminary IC50 findings potentiates it to be further developed as a promising diagnostic bioimaging tool with drug efficacy against chloroquine-resistant P. falciparum.

This paper summarizes some works exploiting the ate-type addition of electron-withdrawing monomers to hydrogenosiloxane groups so as to generate new silicone materials. Two types of monomers were oligomerized onto silicone backbones, namely unsaturated phosphonate and sulfone monomers. Phosphonated silicones are thermally more resistant than conventional silicones and can be transformed into amphiphilic polymers after selective ester hydrolysis. Sulfoned silicones generate solid supramolecular elastomers thanks to the strong pseudo-ionic interactions in play between sulfone groups. Rheology and modulated DSC show a solid/viscoelastic transition around 175°C, which allows using these thermoplastic materials on a larger scale than conventional silicone urea copolymers. These results open new avenues in the generation of silicone block- and grafted-copolymers with unique functionality and properties.

The practical application of a pH-responsive Nanoparticle Drug Delivery System (NDDS) in cancer treatment is often hampered by several issues such as the protection of therapeutic molecules from external stresses, inefficient targeted delivery, sustained drug release, and poor efficacy. This study presents an effective design strategy for the synthesis of a pH-sensitive controlled hydrophobic drug delivery method based on the formulation of chitosan (CS)-coated mesoporous silica nanoparticles (MSNs) through the sol-gel method, where hydrolysis takes place in the acidic medium followed by polycondensation of the hydrolyzed products. For this purpose, NH2 modified-MSNs were prepared by using tetraethyl orthosilicate (TEOS) as precursor and cetyltrimethylammonium bromide (CTAB) as a template, and 3-aminopropyltriethoxysilane (APTES) for amine modification, followed by hydrophobic drug loading and CS coating of various concentrations. Camptothecin (CPT) was used as a model drug. Fabricated monodispersed functionalized nanoparticles had sizes ranging from 200nm to 245nm with an encapsulation efficiency as high as 90%. The highest encapsulation efficiency was found for 1% CS coating, which released 50% drug in 120h at pH 6.4 and 20% at pH 7.4 respectively. These nanoformulations exhibited pH-responsive release patterns of CPT under two different pH values (pH=7.4 and pH=6.4). These results contribute to the optimization of NDDS, with potential implications for nanoformulations designed for controlled and sustained drug release particularly to tumors without affecting healthy cells owing to differences in the pH of the tumor microenvironment and the normal physiological environment of cells.

This study aims to formulate binary cementitious systems containing silica fume (SF) and micro quartz (MQ) to improve cementitious concrete's durability and mechanical properties. In this investigation, we examined the effects of different essential variables, such as the level of SF and MQ replacement and the ratio of the water-binder (w/b). In this study, the w/b ratios were 0.25, 0.3, 0.35, and 0.4. Replacement levels for SF were 8, 10, and 12%, while replacement levels for MQ were 5, 8, 10, 15, 25, and 35%. The porosity and permeability decreased with an increase in replacement levels, regardless of the type of fine material used or the amount of replacement. Meanwhile, the strength increased markedly with SF replacement, reaching its maximum MQ of 25% at the SF level. The strength of the SF mixing was the highest in all mixes, and it remained the highest until 15% of MQ was replaced. The ultrafine size of MQ particles contributes to the improvement of compressive strength, porosity, and permeability in a similar way to SF particles, despite their high crystalline structure. Furthermore, in this study, analysis of variance (ANOVA) was employed to verify the influence of each variable on the studied response.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

Nanomaterials exhibit novel properties and profound attributes as an additive in asphalt binder modification. However, the application of nano-silica in asphalt binders and mixture modification is still limited and further research is required. Along these lines, in this work, nano-silica with a content from 2% to 8% and an increment of 2% were utilized in modifying the bitumen binder type C320, which is considered the most conventional type of bitumen used in Western Australia road asphalt mixtures. Various tests were performed to assess their properties including dynamic shear rheometer, penetration, softening point, and multiple stress creep recovery (MSCR) test. The extracted results revealed an increase in the strength and stiffness properties by lowering the penetration, improving the softening point, and increasing the complex shear modulus of all nano-silica modified bitumen samples. Interestingly, a relatively big content of nano-silica leads to a higher rutting resistance. Nevertheless, the rutting resistance was affected by the size of the nano-silica coated with the silane coupling agent. The ideal sample of nano-silica modified C320 was determined as NS-15nm (NS-A), which can improve the rutting resistance. Nevertheless, the rutting resistance of the modified asphalt mixtures needs to be further investigated in the future to elaborate on the impact of nano-silica as modified binders on the mechanical properties of Australian asphalt mixtures.

Because of their low cost and easy production silica nanoparticles (NPs) are amply used in multiple manufactures as anti-caking, densifying and hydrophobic agents. However, this has increased the exposure levels of the general population and has raised concerns about possible toxicity of this nanomaterial. NPs are known to affect the function of the airway epithelium, but the biochemical pathways targeted by these particles remain largely unknown. Here we investigated the effects of NPs on the responses of cultured human bronchial epithelial (16HBE) cells to the damage-associated molecular pattern ATP, using fluorometric measurements of intracellular Ca2+ concentration. Upon stimulation with extracellular ATP these cells displayed a concentration-dependent increase in intracellular Ca2+, which was mediated by release from intracellular stores. Silica NPs inhibited the Ca2+ responses to ATP within minutes of application and at low micromolar concentrations, which are significantly faster and more potent than those previously reported for the induction of cellular toxicity and pro-inflammatory responses. NPs-induced inhibition appeared to be independent from the increase in intracellular Ca2+ they produce, and via a non-competitive mechanism. These findings suggest that NPs reduce the ability of airway epithelial cells to mount ATP-dependent protective responses such as the increase in mucociliary clearance and cough.

The article describes synthesis of aminoorgano-functionalized silica as a perspective material for catalysis application. The amino groups have electron donor properties valuable for metal chemical state of palladium. So presence of electron donor groups is important for increasing of catalysts stability. The research is devoted to investigation of silica amino-modified support influence on activity and stability of palladium species in 4-nitroaniline hydrogenation process. A series of catalysts with different supports such as SiO2, SiO2-C3H6-NH2 (amino-functionalized silica), γ-Al2O3 and activated carbon were studied. The catalytic activity was studied in the hydrogenation of 4-nitroaniline to 1,4-phenylenediamine. The catalysts were characterized by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and pulse chemisorption of hydrogen. The 5 wt. % Pd/SiO2-C3H6-NH2 catalyst exhibited the highest catalytic activity for 4-nitroaniline hydrogenation with 100% conversion and 99% selectivity with respect to 1,4-phenylenediamine.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

A novel synthetic strategy is disclosed to prepare a new class of metalorganic copolymers which contain iron(II) clathrochelate building blocks by employing a mild and cost-effective copper-catalyzed [4 + 2] cyclobenzannulation reaction, using three specially designed diethynyl iron(II) clathrochelate synthons. The target copolymers CBP1-3 were isolated in high purity and excellent yields as proven by their structural and photophysical characterization, namely, Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption and emission spectroscopies. Thermogravimetric analysis (TGA) of CBP1-3 reveals excellent chemical stability. Investigation of the adsorption properties of the target copolymers towards the carcinogenic methyl red dye from aqueous solution reveals a quantitative uptake in 30 minutes. Isothermal adsorption studies disclose that methyl red uptake from aqueous solution follows Langmuir model for all the target copolymers reaching a maximum adsorption capacity (qm) of 431 mg g‒1, whereas kinetic investigation reveals that the adsorption follows pseudo first-order with an equilibrium adsorption capacity (qe,cal) of 79.35 mg g‒1 and whose sorption property was sustained even after its reuse several times.

The use of intelligent sensor-based packaging in food products provide quick evaluation of the quaility of the food. This study was done to develop bio-based color sensor from surimi-based color sensor incorporated with sappan wood extract (SWE) for smart food packaging. The SWE with different concentration (0.15%, 0.25%, and 0.35%) was incorporated to the myofibrillar protein-based edible film. The sappan wood-surimi edible film (SSEF) was subjected to physical properties analysis and the color changes at different pH values and soaking time at different condition were evaluated. Based on the results, different concentration of the SWE significantly (p<0.05) affected the physical properties of the film. With the increasing of pH values, the darkness, redness, and blueness of the film was increased. Based on the evaluation of the SSEF with different soaking condition, the color changes of the film in acidic condition were more stable than in neutral and alkaline condition. The results from this study showed that SSEF have the possibilities to be used as a smart food packaging possessing the capabilities to act as color sensor due to its sensitivity to the changes in pH condition of the product.

Currently, the use of sustainable chemistry as an ecological alternative for the generation of products or processes, free of polluting substance has assumed a preponderant role. The aim of this work is propose a bioinspired, facile, at low cost, non-toxic and environmentally friendly alternative to obtaining magnetic nanoparticles whit a majority phase of magnetite (Fe₃O₄). Is important to empathize that the synthesis was based on the chemical reduction through the Cnicus Benedictus extract, whose use as reducing agent has not been reported in the synthesis of iron oxides nanoparticles. In addition, the Cnicus Benedictus is abundant endemic plant in Mexico, with several medicinal properties and a large number of natural antioxidants. The obtained nanoparticles exhibited significant magnetic and antibacterial properties and an enhanced photocatalytic activity. The crystallite size of the Fe₃O₄ nanoparticles (Fe₃O₄ NP’s) was calculated by Williamson-Hall method. The photocatalytic properties of the Fe₃O₄ NP´s were studied by kinetics absorptions models in the Congo red (CR) degradation. Finally the antibacterial effect of the Fe3O4 NP´s were evaluated mediated the Kirby-Bauer method against E. coli and S. aureus bacteria. This route offers a green alternative to obtain Fe3O4 NP´s with remarkable magnetic, photocatalytic and antibacterial properties.

In this work was investigated the potential of Bacillus subtilis UCP 0146 in the bioconversion of the medium containing 100% of cassava flour wastewater to obtain bioemulsifier. The evaluation of the production was carried out by the emulsification index (IE24) and surface tension (TS). The ionic charge, stability (temperature, salinity and pH measured by IE24 and viscosity), ability to remove and disperse oil and textile dye were investigated. B.subtilis produced an anionic bioemulsifier in the medium containing 100% of cassava wastewater in condition 4 of the factorial design (9% of the inoculum, at 35 °C and agitation of 100 rpm) with surface tension of 39mN/m, IE24 of 95.2 % and yield 2.69 g.L-1. Stability at different pH (2-8), temperatures (0-120ºC) and NaCl, dispersed (55.83 cm2-ODA) and reduced the viscosity of the burned engine oil (90.5 cP) , removed 94.4% petroleum and demonstrated efficiency in methylene blue removal (62.2%). The bioemulsifier and its synthesis from bacteria and also emphases on the role of surfactants in oil remediation.

Hierarchical micro-/mesoporous graphitic carbon spheres (HGCS) with a uniform diameter of ~0.35 μm were synthesized by Fe-catalyzed graphitization of amorphous carbon spheres resultant from hydrothermal carbonization. The HGCS resultant from 3 h at 900 °C with 1.0 wt% Fe catalyst had high graphitization degree and surface area as high as 564 m²/g. They also exhibited high specific capacitance of 140 F/g at 0.2 A/g, good electrochemical stability with 94% capacitance retention after consecutive 2500 cycles. The graphitization degree of the HGCS contributed about 60% of their specific capacitance, and their specific capacitance per unit surface area was as high as 0.2 F/m² which was much higher than in the most cases of porous amorphous carbon materials reported before. In addition, the HGCS showed a high adsorption capacity of 182.8 mg/g for methylene blue (MB), which was 12 times as high as that in the case of carbon spheres before graphitization.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

Benign design of alkali-activated slag/FA geopolymer paste has intriguing increasing attention for optimizing its service performance. Therefore, the replacement of fly ash (FA) with 10 wt% silica fume (SF) is investigated by mechanical strength after freeze-thawing cycles and microstructure characterization. The results show that an appropriate dosage (30 wt%) of slag is necessary to attain alkali-activated slag/FA geopolymer paste with excellent mechanical performance, and the SF/slag/FA (SF: slag: FA= 10:30:60, wt%) geopolymer paste exerts the compressive and flexural strength of 95.2 and 3.2 MPa, respectively. Meanwhile, the doped 10 wt% SF facilitates the propagation of (N, C)-A–S–H chains, rather than the formation of C-S-H gels, evidenced by the absent exothermic peak at about 861oC from the differential scanning calorimetry (DSC) curves, leading to the increases in the pores volume with a pore diameter<20 nm and tortuosity by mercury intrusion porosimeter (MIP) results, corresponding to an improved freezing-thawing resistance with the residual compressive strength of 52.8 MPa and the weight loss of 10.5% after 300 freeze-thawing cycles. It explores a cost-effective and benign facile approach to designing heating curing-free alkali-activated slag/FA geopolymer paste with good freezing-thawing resistance.

The fireproof design of geopolymer has intriguing increasing attention by adjusting multi-component metallurgical solid wastes, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical strength of slag/FA (slag: FA=30:70, wt.%) geopolymers during building fires. The results show that the replacement of FA with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm, leading to an increase in the compressive or flexural strength below 850℃, “right shifts” of the endothermic peak, appearing uniform and compact fracture surfaces. Meanwhile, the gehlenite and labradorite generate after exposure above 850℃. While the bloating effect of the SF-containing sample occurs at 1200℃, leading to a greater deformation, due to the further restructuring of the amorphous geopolymer chain N-A-S-H or N-(Ca)-A-S-H composed from the [SiO4]4− and [AlO4]5−. It explores an effective approach for improving geopolymer’s fireproof performance by adjusting the solid-waste formulation.

Supplementary cementitious materials (SCMs) are increasingly used in precast concrete industry to enhance concrete strength and durability. SCMs of large market share in precast concrete in-dustry include silica fume, also known as micro-silica and class C fly ash. The main objective of this research is to develop non-proprietary high strength concrete mixes for precast/prestressed concrete industry. Two SCMs are used simultaneously in partial replacement of portland cement to develop ternary mixes. Class c fly ash and silica fume incorporation in the mix design, in ad-dition to low water-to-powder ratio resulted in the successful development of high strength mixes with minimum 24-hour strength in excess of 70 MPa and a final compressive strength ex-ceeding 100 MPa at 28 days. Mechanical properties testing of developed concrete mixes showed that SCMs incorporation resulted in increased values for hardened concrete modulus of elasticity (MoE) and modulus of rupture (MoR). The enhanced concrete properties, mainly high early strength, are highly required in precast concrete industry as it allows for increased productivity of precast facilities and the possibility of pouring high strength slender sections for prestressed concrete applications

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

Highly colloidal Eu-doped Gd2O3 nanoparticles(core-NPs) were synthesized by thermal decomposition via weak base at low temperature (150oC), subsequently, silica layers were deposited to increased colloidal stability, solubility, biocompatibility and no-toxicity at the environmental condition. XRD results indicate the highly purified, crystalline, single phase cubic phase Gd2O3 nanocrystals. TEM image shows the mesoporous thick silica layer was effectively coated over the core nanocrystals, which have irregular size with nearly spherical shape and a mean grain size is about 10-30 nm. Absorption spectra and zeta potential results in aqueous media revealed that solubility, colloidal stability, and biocompatibility character was enhanced from core to core-shell structure because of silica layer surface encapsulation. The samples demonstrate excellent photoluminescence properties (dominant emission 5D0→7F2 transition in red region at 610 nm) indicated the advantage to use in optical bio-detection and bio-labeling etc. The photoluminescence intensity of the silica shell modified core/shell nanoparticles were suppressed relatively core-nanoparticles, it indicates the multi-photon relaxation pathways arising from the surface coated high vibrational energy molecules of the silanol groups. The core/nSiO2/mSiO2 nanocrystals display strong emission (5D0→7F2) transition along with excellent solubility and biocompatibility, which may find promising applications in photonic based biomedical applications.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

Currently, the textile industry is among the most rapidly expanding areas of the economy and is an important source of water pollution. There are many efficient chemical and physical methods for treating textile effluent, but they produce secondary pollutants. Therefore, there is a need to manage the textile waste wastewater. The potential EPS-producing and plant growth-promoting rhizobacteria Lysinibacillus capsici PB300 (T) bacteria strain has been isolated from the bark borer-affected Peltophorum pterocarpum plant and has been determined to be effective in > 95 decolorizing Reactive Red 120, and other azo dyes such as AB11385%, orange II 94.62%, Congo red 94.62%, phenol red 94.54%, and mixtures of azo dyes 81.66%. Physico-chemical factors were optimized manually, including Taguchi design. EPS production, PGPR strain, and fabric discoloration of L. capsici were qualitatively studied. The FTIR, GC-MS, and UV absorbance studies also confirmed that the dye had been broken into its amines. Research findings using enzyme assays have shown that the bacteria Lysinibacillus capsici PB300 (T) can utilize laccase and manganese peroxidase and are capable of degrading dyes significantly. According to this work, immobilised L. capsici cells and the studied four bacterial consortiums, Lysinibacillus capsici PB300 (T), Alcaligenes faecalis subsp. Phenolicus DSM 16503 (T), Acinetobacterbaumanni ATCC 19606 (T), and Pseudomonasaeruginosa JCM 5962 may be employed to degrade RR120 effectively, and it is concluded that L. capsici PB300 (T) bacteria is significantly efficient in textile effluent treatment.

Dye-containing effluent generated in textile industries is polluting and complex wastewater. It should be managed adequately before the final destination. The up-flow anaerobic blanket (UASB) reactor application is an eco-friendly and cost-competitive treatment. The present study briefly reviews the UASB application for dye wastewater valorization. Bioenergy and clean water production potential during dye-containing wastewater treatment are emphasized to promote resource recovery in textile industries. Efficiencies of color and chemical oxygen demand of 50–97% and 60–90% are reported in bench-scale UASB studies. A biogas yield of 0.36–36.04 L d-1 in UASB, which treats dye-containing effluents, is documented. Bioenergy production and water reuse allow environmental and economic benefits. However, data on full-scale UASB treating dye wastewater are missing. Besides, studies on combined systems integrating membrane processes, such as ultrafiltration and nanofiltration, and pretreatment of wastewater and sludge for improvements in biogas production might realize the complete potential for resource recovery of UASB technology.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

Deep eutectic solvents (DESs) have emerged as novel alternatives to common solvents and VOCs. Their employment as electrolytes in battery has been an area of intense research. In this context, understanding changes in physicochemical properties of DESs in the presence of Li salts becomes of utmost importance. Solvatochromic probes have potential to gauze such changes. It is reported herein that one such uv-vis molecular absorbance probe, Reichardt’s betaine dye 33, effectively manifests changes taking place in a DES Glyceline, composed of H-bond accepting salt choline chloride and H-bond donor glycerol in 1 : 2 molar ratio, as salt LiCl is added. Lowest energy intramolecular charge-transfer absorbance band of this dye exhibits 17 nm hypsochromic shift as up to 3.0 molal LiCl is added to Glyceline. The estimated ETN parameter shows linear increase with LiCl mole fraction. Spectroscopic responses of betaine dye 33, N,N-diethyl-4-nitroaniline and 4-nitroaniline are used to assess empirical Kamlet-Taft parameters of dipolarity/polarizability (π*), H-bond donating acidity (α) and H-bond accepting basicity (β) as a function of LiCl concentration in Glyceline. LiCl addition to Glyceline results in increase in α and no change in π*and β. It is proposed that added lithium interacts with oxygen of the –OH functionalities on the glycerol rendering the solvent with increased H-bond donating acidity. It is observed that pyrene, a popular fluorescence probe of solvent polarity, does respond to the addition of LiCl to Glyceline, however, the change in pyrene response starts to become noticeable only at higher LiCl concentration (mLiCl ≥ 1.5 m). Reichardt’s betaine dye is found to be highly sensitive and versatile in gauzing physicochemical properties of DESs in the presence of LiCl.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

Hydrogels can offer many opportunities for drug delivery strategies. They can be used on their own or their benefits can be further exploited in combination with other nanocarriers. Intelligent hydrogels that react to changes in the surrounding environment can be utilized as gatekeepers and provide sustained on demand drug release. In this study, a hybrid nanosystem for tempera-ture and pH sensitive delivery was prepared from MCM-41 nanoparticles grafted with newly synthesized thermosensitive hydrogel (MCM-41/AA-g-PnVCL). The initial particles were chemi-cally modified by carboxyl groups attachment. Later, they were grafted with agar (AA) and vi-nylcaprolactam (VCL) by free radical polymerization. Doxorubicin was applied as a model hy-drophilic chemotherapeutic drug. The successful formulation was confirmed by FT-IR and TGA. Transmission electron microscopy and dynamic light scattering analysis showed small particles with negative zeta potential. Their release behaviour was investigated in vitro in different pH media and at different temperatures. At tumor simulating conditions (40ºC and pH 4.0) doxoru-bicin was almost completely released within 72 hours. The biocompatibility of the proposed na-noparticles was demonstrated by in vitro haemolysis assay. These results suggest the possible parenteral application of the newly prepared hydrogel-functionalized mesoporous silica nanopar-ticles for temperature-sensitive and pH-triggered drug delivery at the tumor site.

The risk of lung exposure to silica nanoparticles (SiNPs) and related lung inflammatory injury is increasing with the wide application of SiNPs in a variety of industries. A growing body of research has revealed that cyclooxygenase (COX)-2/ prostaglandin E2 (PGE2) up-regulated by SiNPs toxicity has a role during pulmonary inflammation. The detailed mechanisms underlying SiNPs-induced COX-2 expression and PGE2 synthesis remain unknown. The present study aims to dissect the molecular components involved in COX-2/PGE2 up-regulated by SiNPs in human pulmonary alveolar epithelial cells (HPAEpiCs) which are one of the major targets while SiNPs are inhaled. In the present study, we demonstrated that SiNPs induced COX-2 expression and PGE2 release, which were inhibited by pretreatment with a reactive oxygen species (ROS) scavenger (edaravone) or the inhibitors of proline-rich tyrosine kinase 2 (Pyk2, PF-431396), epidermal growth factor receptor (EGFR, AG1478), phosphatidylinositol 3‑kinase (PI3K, LY294002), protein kinase B (Akt, Akt inhibitor VIII), p38 mitogen-activated protein kinase (MAPK) (p38 MAPK inhibitor VIII), c-Jun N-terminal kinases (JNK)1/2 (SP600125), Forkhead Box O1 (FoxO1, AS1842856), and activator protein 1 (AP-1, Tanshinone IIA). In addition, we also found that SiNPs induced ROS-dependent Pyk2, EGFR, Akt, p38 MAPK, and JNK1/2 activation in these cells. These signaling pathways induced by SiNPs could further cause c-Jun and FoxO1 activation and translocation from the cytosol to the nucleus. AP-1 and FoxO1 activation could increase COX-2 and PGE2 levels induced by SiNPs. Finally, the COX-2/PGE2 axis might promote the inflammatory responses in HPAEpiCs. In conclusion, we suggested that SiNPs induced COX-2 expression accompanied by PGE2 synthesis mediated via ROS/Pyk2/EGFR/PI3K/Akt/p38 MAPK- and JNK1/2-dependent FoxO1 and AP-1 activation in HPAEpiCs.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

Recycling of metallurgical solid waste has intriguing increasing attention for fabricating cementitious materials, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical properties of slag/FA geopolymers. The results show that the replacement with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm at room temperature, leading to an increase in the compressive or flexural strength, “right shifts” of endothermic peak and the initial-final temperature of mass loss, presenting a denser and compact fracture surface. Meanwhile, the mineral phase of gehlenite and labradorite emerges after exposure above 850℃ from the XRD results. Furthermore, the bloating effect of the incorporated SF occurs due to the formation of a liquid phase altogether with the amorphous silicates after exposure to 1200℃, leading to a greater deformation and enhancement of restructuring involved in the [SiO4]4− and [AlO4]5−. It explores an effective recycling approach for fabricating paste binders using metallurgical solid wastes.

In this work, polyacrylic acid-functionalized MCM-41 was synthesized, which was further interacted with calcium ions, to realize enhanced pH-responsive nanocarrier for sustained drug release. First, mesoporous silica nanoparticles (MSNs) were prepared by the sol-gel method. Afterward, (3-trimethoxysilyl)propyl methacrylate (TMSPM) modified surface was prepared by using the post-grafting method, then polymerization of acrylic acid was proceeded. After adding calcium chloride solution, polyacrylic acid-functionalized MSNs with calcium-carboxyl ionic bonds in the polymeric layer, which can prevent the cargo from leaking out of the mesopore, were prepared. The structure and morphology of the modified nanoparticles (PAA-MSNs) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, etc. The controlled release of guest molecules was studied by using 5-fluorouracil (5-FU). The drug molecules-incorporated nanoparticles showed different releasing rates under different pH conditions. It is considered that our current materials have the potential as pH-responsive targeted nanocarriers in the field of medical treatment.

Background: Work experience is a key factor that influences safety awareness among workers. This study investigated the influence of work experience on the level of awareness on adverse health effects of silica dust exposure among stone quarry workers in Ghana while controlling for theoretically relevant compositional and contextual factors, evaluated the magnitude and order of association between the predictors and the predicted variable. Method: A cross-sectional survey data of 524 randomly selected stone quarry workers were subjected to multivariate statistical analyses. Results: Stone quarry workers who had 6 to10 years and more than 10 years of work experience were 48% (OR = 1.475, P = 0.021) and 82% (OR = 1.816, P = 0.003) respectively more likely to be aware of the adverse health effects of silica dust exposure compared to their counterparts who had 1 to 5 years work experience. Workers who had secondary or higher education were 32% (OR = 1.320, P = 0.036) more likely to be aware of the adverse health effects of silica dust exposure compared to their counterparts who had no education. Conclusion: These findings provide relevant information for managers and policymakers to plan and maximize awareness on silica dust health hazards among silica exposed workers.

Nanoparticles (NPs) have various applications in medicine, cosmetics, optics, catalysis, environmental purification, and other areas nowadays. With an increasing annual production of NPs, the risks of their harmful influence to the environment and human health is rising. Currently, our knowledge about the mechanisms of interaction between NPs and living organisms is limited. Additionally, poor understanding of how physical and chemical characteristic and different conditions influence the toxicity of NPs restrict our attempts to develop the standards and regulations which might allow us to maintain the safe living conditions. The marine species and their habitat environment are under continuous stress due to anthropogenic activities which result in the appearance of NPs in the aquatic environment. Our study aimed to evaluate and compare biochemical effects caused by the influence of different types of carbon nanotubes, carbon nanofibers, and silica nanotubes on four marine microalgae species. We have evaluated the changes in growth-rate, esterase activity, membrane polarization, and size changes of microalgae cells using flow cytometry method. Our results demonstrated that toxic effects caused by the carbon nanotubes strongly correlated with the content of heavy metal impurities in the NPs. More hydrophobic carbon NPs with less ordered structure had a higher impact on the red microalgae P. purpureum because of higher adherence between the particles and mucous covering of the algae; silica NPs caused significant inhibition of microalgae growth-rate predominantly produced by mechanical influence.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Zinc nanoparticles (ZnNPs) open new opportunities for biomedical applications as a strategy against microbes and dye removal in an efficient way. The composite ZnNPs using Rhododendron arboreum (R. arboreum) stem bark were synthesized and characterized for UV-visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The synthesized nanoparticles showed zones of inhibition of 23±0.09, 18±0.1 and 16±0.05 mm, against the Klebsiella pneumoniae (K. pneumoniae), Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli strains. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) values against K. pneumoniae, S. aureus, and E. coli were found to be 34±0.21 and 72.71±0.47, 47±0.11 and 94.86±0.84 and 94±0.18 and 185.43±0.16 µg/mL, respectively. The biosynthesized ZnNPs resulted in significant eradication of the outer and inner membranes of the bacterial cells. Likewise, the synthesized ZnNPs showed time-dependent photocatalytic degradation activity and revealed 65% methyl orange dye degradation with an irradiation period of 6 hours. The findings of this study suggest the suitability of the novel R. arboreum stem bark-based ZnNPs as an effective ameliorant against bactericidal activities and photocatalysts for the removal of hazardous water contaminants.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

The UV/Vis absorption energies (νmax) of different solvatochromic probes measured in co-solvent/water mixtures are analysed as a function of the average molar concentration (Nav) of the solvent composition. Nav is discussed in terms of the underlying average molar mass (mol average or mass average) of the mixture. ET(30) of Reichardt`s dye B30 is the focus of the analysis. Methanol, ethanol, 1,2-ethanediol, 2-propanol, 2-methyl-2-propanol, 2-butoxyethanol, formamide, N-methylformamide (NMF), dimethylformamide (DMF), N-formylmorpholine (NFM), 1,4-dioxane and DMSO were used as co-solvents. Significant linear dependencies of ET(30) as a function of Nav can be demonstrated for formamide/water, 1,2-ethanediol/water, NMF/water and DMSO/water mixtures over the whole composition range. These mixtures belong to the group of solvents that do not enhance the water structure according to the Marcus classification. The specifics of the 1,4-dioxane/water mixtures are discussed. For alcohol/water mixtures with enhanced water structure, the influence of the solvent microstructure on ET(30) is particularly evident.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

Zinc oxide (ZnO) nanoparticles (NPs) were synthesized using Rosmarinus officinalis leaf extract at 80 ° C (ZnO-80) and 180 ° C (ZnO-180). The biosynthesized ZnO NPs were characterized and their photocatalytic activity was evaluated for the degradation of methylene blue (MB) and crystal violet (CV) under sunlight irradiation. The results of the characterizations by XRD, TEM and SEM showed that the size of the NPs of ZnO-80 was smaller than that of ZnO-180 which exhibited flakier agglomerated spherical structures. Photocatalytic tests showed ZnO-80 which was prepared by a cheap and easy procedure compared to ZnO-180 effectively degrades MB and CV dyes under sunlight. The superior performance of ZnO-80 over ZnO-180 can be explained by the differences in their textural properties. This is because ZnO-80 has a smaller crystallite size, a specific surface area and a higher pore volume than ZnO-180. Fourier-transform infrared spectroscopy (FTIR) analyzes revealed that both samples contained an adsorbed carboxylate group (COO-), and accordingly a mechanism was proposed for the formation of ZnO NPs that include the carboxyl group.

The presence of azo dyes in textile effluents is an issue of major concern due to their potential impact on the environment and human health. In this study we investigate the photocatalytic degradation under visible light of Reactive Violet 5 (RV5), an azo dye widely used in the textile industry. A preliminary screening of different titania-based catalysts was carried out to identify the best candidate for RV5 removal. The selected catalyst was then tested in a stirred and aerated lab-scale reactor illuminated with a light LED source (λmax = 460 nm). The effects of pH, catalyst load and hydrogen peroxide additions on the efficiency of dye removal were evaluated. Under the best conditions (pH 10, 3 g/L of catalyst and 60 mM hydrogen peroxide), the dye solution was completely decolorized in about 2 h. Overall, the results obtained suggest that the proposed process may represent a suitable method for the removal of RV5 from textile effluents.

Mesoporous silica nanoparticles (MSNs) can be used as carrier materials for the controlled release of pesticides while reducing their negative environmental impact. In this study, we screened an active ingredient, p-cymene (PC), with an excellent inhibitory effect on rice bacterial blight. Subsequently, the PC was successfully loaded onto MSNs via physisorption(PC@MSNs). PC@MSNs, characterized by a regular spherical shape, smooth surface, and an MSN average size of 262.9 nm, achieved an 8.6 % drug loading capacity. The release kinetics of the PC from the PC@MSNs demonstrated a sustained release (288 h) pattern influenced by drug diffusion. The efficacy of the PC@MSNs against Xanthomonas oryzae pv. Oryzae paralleled those of PC. Acute toxicity assays re-vealed that the PC@MSNs were less toxic to aquatic life (LC50=257.867 mg/L) and that the formu-lation showed no adverse effects on rice seedling growth. In summary, these results suggest that PC@MSNs can broaden PC's application scope in managing rice diseases.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

Reinforcement corrosion due to chloride attack is of major economic significance for reinforced concrete structures. Pozzolans are known to inhibit corrosion initiation mainly by reducing concrete permeability. However, there is evidence in the literature that changes in the chemical environment in the concrete due to the pozzolans may be creating improved corrosion resistance, by themselves. In this study, the composition of a pore solution of mature hydrated cement paste containing silica-fume at different ratios was analyzed. The electrochemical behavior of reinforcing steel was studied in simulated pore solutions with silicate concentrations ranging from 0 to 35.6 mM, which are within the concentration range found by pore solution extraction to be up to 49 mM. Polished reinforcing steel specimens were used for cyclic voltammetry in simulated pore solutions with chloride concentrations of 10-20%. Better corrosion protection was found with increasing silicate concentration up to 3.56 mM. This was indicated by lower corrosion currents both in the passive state and after anodic activation. Anodic activation of steel in a 35.6 mM silicate solution with 20% NaCl yielded a higher potential than the anterior potential.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

This work describes the preparation of mesoporous silica by the green reaction of rice husk ash (RHA) with glycerol, followed by the modification and the potential use as a drug carrier. The reaction was carried out at 215 °C for 2 h. The solution was further hydrolyzed with deionized water and aged for various times (24, 48, 120, 360, 528 and 672 h) before calcinations at 500 oC for 24 h. Further treatment of prepared mesoporous silica was performed using trimethylmethoxysilane (TMMS) to obtain hydrophobic Mesoporous silica. For all synthesized silica, silica contents were as high as 95%wt, whereas organic residues were less than 3%wt. RHA-glycerol showed the highest specific surface area with smallest pore diameter (205.70 m2/g, 7.46 nm) when aged for 48 h. The optimal hydrolysis-ageing period of 120 h resulted in 500.7 m2/g BET surface area, 0.655 cm3/g pore volume and 5.23 nm pore diameter. The surface modification of RHA-glycerol was succeeded through the reaction with TMMS as confirmed by FTIR. Ibuprofen was selected as a model drug for the adsorption experiments. The adsorption under supercritical CO2 was carried out at isothermal temperature of 40 ˚C and 100 bar, % ibuprofen loading of TMMS modified mesoporous silica (TMMS-g-MS) was 6 times less than mesoporous silica aged for 24 h (MS-24h) due to the hydrophobic nature of modified mesoporous silica, not surface and pore characteristics. The release kinetics of ibuprofen-loaded mesoporous silicas were also investigated in vitro. The release rate of ibuprofen-loaded MS-24h was much faster than that of ibuprofen-loaded TMMS-g-MS, but comparable to the crystalline ibuprofen. The slower release rate was attributed to the diffusion control and the stability of hydrophobic nature of modified silica. This would allow the design for the controlled release drug delivery system.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

Usually, the two-bath dyeing process using disperse dyes and reactive dyes separately was employed for the dyeing of PC blends. The cost of the double bath, dyeing cycle, energy consumption and chemical consumption is quite higher than the one-step or single bath dyeing methods. In this study, the one-bath dyeing process using one kind of dye was investigated. Polyester cotton blends dyed in one-bath one-step dyeing methods with disperse dye after surface modifications of cotton by acetylation methods were studied. Surface modification of cotton was carried out using fibrous acetylation methods. The effect of acetic anhydride and time on percent acetyl content at room temperature was studied. Modified polyester/cotton was carried out in HTHP dyeing machine incorporates with different dye concentrations and dyeing temperature. Surface chemistry, thermal decomposition property and moisture regain of modified polyester/ cotton blend are evaluated. The color strength of the dyed fabrics and their fastness properties to washing, light, and rubbing as well as tear strength and abrasion resistance were evaluated. The effect of dye concentration and temperature color strength, tensile strength warp and weft direction was assessed. The optimum value for surface modification was obtained with a concentration of acetylation agent 16% and time of reaction 2.5 hours, gave percent acetylation of 34. An FTIR spectrum shows acetylation resonance. The experiment result of dyeing showed that the optimum value was obtained with dye concentration above 1% at a temperature of 120oC, warp tensile strength decreased by 12% and weft tensile strength was decreased by 9% from the control half-bleached fabric. Results of this study showed that a one-step one-bath dyed modified polyester/cotton blend with disperse dye fabric presents good fastness property compared with conventional two-bath dyed fabric as well as colour strength values.

Food analysis demands fast methods for routine control and high throughput of samples. Chromatographic separation enables simultaneous determination of numerous compounds in complex matrices, several approaches increasing separation efficiency and speed of analysis were involved. In this work, modern types of column with monolithic rod or superficially porous particles were employed and compared for determination of eight synthetic food dyes, their chromatographic performance was evaluated. During method optimization, cyano stationary phase Chromolith Performance CN 100 × 4.6 mm and Ascentis Express ES-CN 100 × 4.6 mm, 5 µm were selected for the separation of polar colorants. The separation was performed by gradient elution of acetonitrile/methanol and 2% water solution of ammonium acetate at flow rate 2.0 ml min-1. Mobile phase composition and the gradients were optimized in order to enable efficient separation on both columns. The method using fused-core particle column provided higher separation efficiency, narrow peaks of analytes resulted in increased peak capacity and shortening of analysis time. After the validation, the method was applied for analysis of colored beers, soft drinks and candies.

Gold nanoclusters (AuNCs) with fluorescence in the Near Infrared (NIR) by both one- and two-photon electronic excitation were incorporated in mesoporous silica nanoparticles (MSNs) using a novel one-pot synthesis procedure where the condensation polymerization of alkoxysilane monomers in the presence of the AuNCs and a surfactant produce hybrid MSNs of 49 nm diameter. This method was further developed to prepare 30 nm diameter nanocomposite particles with simultaneous NIR fluorescence and superparamagnetic properties, with a core composed of superparamagnetic manganese ferrite nanoparticles (MnFe2O4) coated with a thin silica layer, and a shell of mesoporous silica decorated with AuNCs. The nanocomposite particles feature NIR-photoluminescence with 0.6% quantum yield and large Stokes shift (290 nm), and superparamagnetic response at 300 K, with a saturation magnetization of 13.4 emu g-1. The conjugation of NIR photoluminescence and superparamagnetic properties in the biocompatible nanocomposite has high potential for application in multimodal bioimaging.

Nanocomposite hydrogels offer remarkable potential for applications in bone tissue engineering. They are synthesized through the chemical or physical crosslinking of polymers and nanomaterials, allowing for the enhancement of their behaviour by modifying the properties and compositions of the nanomaterials involved. However, their mechanical properties require further enhancement to meet the demands of bone tissue engineering. Here, we present an approach to improve the mechanical properties of nanocomposite hydrogels by incorporating polymer grafted silica nanoparticles into a double network inspired hydrogel (gSNP Gels). The gSNP Gels were synthesised via a graft polymerization process using a redox initiator. gSNP Gels were formed by grafting 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as the first network gel followed by a sequential second network acrylamide (AAm) onto amine functionalized silica nanoparticles (ASNPs). We utilized glucose oxidase (GOx), to create an oxygen-free atmosphere during polymerization resulting in higher polymer conversion compared to argon degassing. The gSNP Gels showed excellent compressive strengths of 13.9 ± 5.5 MPa, a strain of 69.6 ± 6.4%, and a water content of 63.4% ± 1.8. The synthesis technique demonstrates a promising approach to enhance the mechanical properties of hydrogels, which can have significant implications for bone tissue engineering and other soft tissue applications.

Insects quickly develop resistance to conventional chemical insecticides. The use of silica nanoparticles (SiO₂NPs) is a promising new approach for managing insect pests. The insects that have been studied are, in most cases, external feeders and internal leaf feeders have not been well studied. Here, we investigate the efficiency of SiO₂NPs in controlling the American serpentine leafminer Liriomyza trifolii (Diptera: Agromyzidae), a devastating insect pest of a wide range of crops. SiO₂NPs at concentrations of 50, 100, 200 and 400 mg/L compared to a control of distilled water were applied to intact Phaseolus vulgaris leaves by spraying to evaluate their effects, via the plant, on the number, survival, developmental/feeding speed, body mass/size and sex ratio of L. trifolii released after spraying. A qRT-PCR analysis was conducted to assess oxidative stress in L. trifolii based on the gene expression level of the two major antioxidant enzymes; catalase and superoxide dismutase. The number of mines, survival rate and puparia weight were lower than the control at the highest concentration of SiO₂NPs, while pupariation was delayed at most of the concentrations studied and puparium weight/size decreased at low concentrations. Sex ratio was not affected by SiO₂NPs. Gene expression levels of the antioxidant enzymes at the pupal stage were not significantly affected by SiO₂NPs at any concentration but some individuals showed up-regulation at low SiO₂NP concentrations, inferring development of resistance. This study demonstrated that a priori application of the highest concentration of SiO₂NPs to plants effectively reduces a leafminer population but that application of even the lowest concentration can decrease the life history trait values of surviving leafminers.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures. The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding. Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethane string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.