Human motion analysis using inertial measurement units (IMUs) has recently been shown to provide accuracy similar to the gold standard, marker-based optical motion capture, but at much lower costs and while being less restrictive and time-consuming. However, IMU-based motion analysis requires precise knowledge of the orientation in which the sensor is attached to the body segments. This knowledge is commonly obtained via an anatomical calibration procedure based on precisely defined poses or motions, which is time-consuming and error-prone. In the present work, we propose a self-calibrating approach for magnetometer-free joint angle tracking that is suitable for joints with two degrees of freedom (DoF), such as the elbow, ankle, and metacarpophalangeal finger joints. The proposed methods exploit kinematic constraints to simultaneously identify the joint axes and the heading offset. The experimental evaluation shows that the proposed methods are able to estimate plausible and consistent joint axes from just ten seconds of arbitrary elbow joint motion. Comparison with optical motion capture shows that the proposed methods yield joint angles with similar accuracy as a conventional IMU-based method while being much less restrictive. Therefore, the proposed methods improve the practical usability of IMU-based motion tracking in many clinical and biomedical applications.

The satellite Earth observation (EO) sector is burgeoning with hundreds of commercial satellites being launched each year, delivering a rich source of data that could be exploited for societal benefit. Data streams from the growing constellation of commercial satellites are of variable quality, limiting the potential for their combined use in science applications that need long time-series data from multiple sources. The quality of calibration performed on optical sensors onboard many satellite systems is highly variable due to calibration methods, sensor design, mission objective, budget, or other operational constraints. A small number of currently operating well-characterised satellite systems with onboard calibration, such as Landsat-8/9, Sentinel-2, and planned future missions like the NASA Climate Absolute Radiance and Refractivity Observatory (CLARREO) Pathfinder, the European Space Agency (ESA) Traceable Radiometry Underpinning Terrestrial and Helio Studies (TRUTHS), and LIBRA from China, are considered benchmarks for optical data quality due to their traceability to international measurement standards. This paper describes the concept of a space-based transfer calibration radiometer called the Satellite Cross-Calibration Radiometer (SCR) that would enable the calibration parameters from satellites such as Landsat-8/9, Sentinel-2, or other benchmark systems to be transferred to a range of commercial optical EO satellite systems while in orbit. A description of the key characteristics of the SCR to successfully operate in orbit and transfer calibration from Reference systems to Client systems is presented. A system like the SCR in orbit could complement SI-Traceable satellites (SITSats) to improve data quality and consistency and facilitate the interoperable use of data from multiple optical sensor systems for delivering higher returns on the global investment in EO.

Fluxgate magnetometers require calibration methods appropriate to their application levels and particularities; however the development of fully controlled calibration procedures presents a particular challenge regarding the inevitable influence of the local geomagnetic field and other external interferences when a laboratory with magnetically shielded walls is not available. In that context, we discussed the development of an automated calibration method for fluxgate magnetometers, considering those limitations in time and space, and avoiding some of the problems commonly found in other proposed solutions for the same challenge. For this task, we designed and built a new set of high level procedures, electronic systems and software, which perform active testing and automated calibration of fluxgate magnetometers, considering some resource constraints and employing instruments commonly found in electronic calibration laboratories.

Most of the existing calibration methods for binocular stereo vision sensor (BSVS) depend on high-accuracy target with feature points that are difficult to manufacture and costly. In complex light conditions, optical filters are used for BSVS, but they affect imaging quality. Hence, the use of a high-accuracy target with certain-sized feature points for calibration is not feasible under such complex conditions. To solve these problems, a calibration method based on unknown-sized elliptical stripe images is proposed. With known intrinsic parameters, the proposed method adopts the elliptical stripes located on the parallel planes as a medium to calibrate BSVS online. In comparison with the common calibration methods, the proposed method avoids utilizing high-accuracy target with certain-sized feature points. Therefore, the proposed method is not only easy to implement but is a realistic method for the calibration of BSVS with optical filter. Changing the size of elliptical curves projected on the target solves the difficulty of applying the proposed method in different fields of view and distances. Simulative and physical experiments are conducted to validate the efficiency of the proposed method. When the field of view is approximately 400 mm × 300 mm, the proposed method can reach a calibration accuracy of 0.03 mm, which is comparable with that of Zhang’s method.

This review paper deals with recently proposed algorithms for distributed blind macro-calibration of sensor networks based on consensus (synchronization), not requiring any fusion center. The basic algorithm, performing the estimation of the local calibration parameters, is derived commencing from appropriate local criteria, and developing the corresponding gradient descent scheme. It is shown that the estimated parameters of the calibration functions asymptotically converge, in the mean-square sense and with probability one (w.p.1), to such values that ensure consensus on calibrated sensor gains and calibrated sensor offsets. For the more realistic case in which additive measurement noise, communication dropouts and additive communication noise are present, two algorithm modifications are introduced: one using a simple compensation term, and a more robust one based on an instrumental variable. By utilizing stochastic approximation arguments it is shown that the modified algorithms also achieve asymptotic agreement for calibrated sensor gains and offsets, in the mean-square sense and w.p.1. Convergence rate is analyzed in terms of an upper bound of the mean-square error. It is also shown that the communications between nodes can be completely asynchronous, which is of substantial importance for real-world applications. Suggestions for design of \textit{a priori} adjustable weights are given. Finally, it is shown that, if there is a subset of (precalibrated) reference sensors with fixed calibration parameters, the calibrated sensor gains and offsets of the rest of the sensors do not achieve consensus - they converge to different points dictated by the reference sensors and the network characteristics. Wide applicability and efficacy of these algorithms are illustrated on several simulation examples.

This study proposes self-calibration of capacitor mismatch errors for high-resolution pipeline analog-to-digital converters (ADCs). The proposed calibration circuit recursively amplifies the capacitor mismatch error by re-utilizing a multiplying digital-to-analog converter in a pipeline stage without increasing the circuit complexity, and the amplified error voltage is converted into digital code by utilizing the remaining pipeline stages. Error correction is performed by subtracting the digital code from the ADC output during normal operation. A prototype of a 12-bit pipeline ADC is fabricated in a 0.18 µm standard CMOS process. The ADC comprises eight 1.5-bit stages, followed by a 4-bit flash ADC as the final stage; the capacitor mismatch errors in the first two pipeline stages are corrected by utilizing the proposed self-calibration technique. At a sampling rate of 30 MS/s, the measured differential and integral nonlinearities improve from +0.82/-0.75 and +1.12/-1.79 to +0.45/-0.41 and +0.47/-0.91 after calibration, respectively. Further, the measured dynamic performances improve significantly with calibration. For an input frequency of 2.09 MHz, the ADC achieves a spurious-free dynamic range (SFDR) and signal-to-noise and distortion ratios (SNDR) of 69.3dB and 63.9dB before calibration, respectively. After calibration, the SFDR and SNDR increase to 84.1dB and 68.9dB, respectively, and the effective number of bits is approximately 11.1bit. The power consumption of the ADC is 35mW under 1.8V supply, and the resulting figure of merit is 514fJ/conversion step.

The capacitor-mismatch among diverse defects caused by the manufacturing process variations significantly affects the linearity of capacitor-array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation-register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor-array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor-mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor-arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor-arrays of the two ADCs can be reconfigured to be connected to each other, so that Cn of ADC1 can be connected with two of Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total-harmonic-distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8-dB and 6.4-dB, respectively.

This paper presents a complete control strategy of the active return-to-center (RTC) control for electric power steering (EPS) systems. We first establish the mathematical model of the EPS system and analyze the source and influence of the self-aligning torque (SAT). Second, based on the feedback signals of steering column torque and steering wheel angle, we give the trigger conditions of a state switch between the steering assist state and the RTC state. In order to avoid the sudden change of the output torque for the driving motor when the state switches frequently between the steering assist state and the RTC state, we design an undisturbed state switching logic algorithm. This state switching logic algorithm ensures that the output value of the RTC controller is set to an initial value and increases in given steps up to a maximum value after entering the RTC state, and the output value of the RTC controller will reduce in given steps down to zero when exiting the RTC state. This therefore ensures smooth switch control between the two states and improves the driver’s steering feeling. Third, we design the RTC controller, which depends upon the feedback signals of the steering wheel angle and the angular velocity. In addition, the controller increases the auxiliary control function of the RTC torque based on vehicle speed. The experimental results show that the active RTC control method does not affect the basic assist characteristics, which effectively reduces the residual angle of the steering wheel at low vehicle speed and improves the RTC performance of the vehicle.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

Glaucoma secondary to Peters' anomaly (PA) is an important factor affecting visual prognosis, but there are few reports on it. This study aimed to investigate the characteristics of glaucoma asso-ciated with PA and glaucoma surgery outcomes. This retrospective study included 31 eyes of 20 patients with PA. PA was classified into three stages: Stage 1, with a posterior corneal defect only; Stage 2, a corneal defect with iridocorneal adhesion; and Stage 3, a corneal defect with lens ab-normalities. The associations between glaucoma and anterior segment dysgenesis severity, visual prognosis, and glaucoma surgery outcomes were analyzed. Sixteen eyes of 10 patients developed glaucoma. Stage 1 PA had no glaucoma, 52% of Stage 2 had glaucoma, and 75% of Stage 3 had glaucoma. Of the 16 eyes with glaucoma, 11 underwent surgery. Eight of these 11 eyes achieved intraocular pressure (IOP) control. Five of the nine eyes that underwent trabeculotomy (TLO) succeeded, and none had corneal staphyloma. Three of the four eyes for which TLO was ineffective had corneal staphyloma (P=0.0331). Patients with PA are more likely to develop glaucoma as anterior segment dysgenesis progresses, and the effect of TLO is limited if corneal staphyloma is present.

Road segment can be estimated from GPS trajectories by averaging. However, most existing averaging strategies suffer from high complexity or poor accuracy. For example, finding the optimal mean for a set of sequences is known to be NP-hard, while using Medoid compromises the quality. In this paper, we introduce three extremely fast and practical methods for solving the problem. The methods first analyze three descriptors and then use either a simple linear model or a more complex curvy model depending on an angle criterion. The results outperform Medoid and provide equal or better accuracy than the best existing methods while being very fast, and therefore suitable for real-time processing.

To avoid the endless accumulation of QTL effects during pyramiding breeding, QTL epistasis plays a role of homeostasis. Four single-segment substitution lines with heading date QTLs were utilized to construct pyramiding materials with dual QTLs and triple QTLs, allowing for the estimation of QTL epistatic effects on heading date in rice. The epistatic components of dual QTL and triple QTL interactions were analyzed using data from three seasons of two years. All four QTLs can be considered as dominant loci, demonstrating superdominance. 75% of dual QTL interactions and 81.25% of triple QTL interactions obtained statistically significant results, reaffirming the prevalence of epistasis. Interactions of four QTLs with three positive effects and one negative effect generated 62.5% negative dual QTL epistatic effects and 57.7% positive triple QTL epistatic effects, forming the balance relationship “positive-negative-positive”. In fact, QTL effects were consistently partially neutralized by mixed QTL epistatic effects so as to control the infinite accumulation of QTL effects. QTL epistasis plays a role of homeostasis on heading date in rice. However, there were two exceptions. The directions of OsMADS50 and Hd3a-2 effects were consistently aligned with those of their mixed epistases, suggesting that the QTL or gene could be employed in pyramiding breeding with different objectives. This study elucidated the mechanism of epistatic interactions among four QTLs and provided valuable genetic resources for improving heading date in rice.

Study evaluates the characteristics and clinical course of patients with iris cysts in the long term of follow-up (24-48 months). We analyzed retrospectively the medical records of 39 patients with iris cysts (27 female and 12 male). Age, visual acuity, intraocular pressure (IOP), slit-lamp evaluation, and ultrasound biomicroscopy images were assessed. The mean age at diagnosis was 40.6±17.48 years. 30 (76.9%) cysts were peripheral, 5 (12.8%) cysts located at the pupillary margin, 2 (5.1%) cysts were midzonal and 2 (5.1%) multichamber cysts extended from the periphery to the pupillary margin. 23 (59%) cysts were in the lower temporal quadrant, 11 (28.2%) cysts in the lower nasal quadrant, and 5 (12.8%) cysts in the upper nasal quadrant. Cyst size was positively correlated with the age of the patients (rs = 0.38, p = 0.003) and negatively correlated with visual acuity (rs = -0.42, p = 0.014). No cyst growth was documented. The only complication was an increase in IOP in 3 (7.7%) patients with multiple cysts. The anatomical location of cysts cannot differentiate them from solid tumors. The vast majority of cysts are asymptomatic, do not increase in size, and do not require treatment in long-term follow-up.

It is one of very important and basic problem in compute vision field that recovering depth information of objects from two-dimensional images. In view of the shortcomings of existing methods of depth estimation, a novel approach based on SIFT (the Scale Invariant Feature Transform) is presented in this paper. The approach can estimate the depths of objects in two images which are captured by an un-calibrated ordinary monocular camera. In this approach, above all, the first image is captured. All of the camera parameters remain unchanged, and the second image is acquired after moving the camera a distance d along the optical axis. Then image segmentation and SIFT feature extraction are implemented on the two images separately, and objects in the images are matched. Lastly, an object depth can be computed by the lengths of a pair of straight line segments. In order to ensure that the best appropriate a pair of straight line segments are chose and reduce the computation, the theory of convex hull and the knowledge of triangle similarity are employed. The experimental results show our approach is effective and practical.

This research paper examines the evolution of car purchasing behaviour among consumers in India from 2010 to the present. Through extensive literature review and questionnaire survey, it explores the reasons behind the changing preferences and decision-making processes of consumers in the Indian automobile market. The study draws upon various sources, including market research reports, industry publications, academic studies, and consumer surveys, to provide a comprehensive analysis of the factors influencing car purchasing behaviour in India over the last decade. The findings of this research paper can help automakers and marketers better understand consumer preferences and develop effective strategies to cater to the evolving needs of the Indian car market.

Wireless Sensor Network is an emerging technology and the collaboration of wireless sensors becomes one of the active research areas to utilize sensor data. Various sensors collaborate to recognize the changes of a target environment, to identify, if occurs, any radical change. For the accuracy improvement, the calibration of sensors has been discussed, and sensor data analytics are becoming popular in research and development. However, they are not satisfactorily efficient for the situations where sensor devices are dynamically moving, abruptly appearing or disappearing. If the abrupt appearance of sensors is a zero-day attack and the disappearance of sensors is an ill-functioning comrade, then sensor data analytics of untrusted sensors will result in an indecisive artifact. The pre-defined sensor requirements or meta-data based sensors verification is not adaptive to identify dynamically moving sensors. This paper describes a deep-learning approach to verify the trustworthiness of sensors by considering the sensor data only, without having to use meta-data about sensors or to request consultation from a cloud server. The contribution of this paper includes 1) quality preservation of sensor data for mining analytics and 2) authenticity verification of dynamically moving sensors with no external consultation.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Aiming at the problem of low charging efficiency caused by the scattered sensor nodes in traditional wireless rechargeable sensor networks (WRSNs), a UAV-assisted WRSN Online Charging Strategy Based on Dynamic Queue and Improved K-means (UOCS) is proposed. The scheme assumes that the energy consumption of nodes is unpredictable, and only generates charging requests when the energy is lower than a threshold, and performs on-demand responses to nodes that issue charging requests. The scheme combines the characteristics of one-to-one charging of UAVs, the selection and allocation timing of waiting queues and the number of UAVs, and the improved K-means partitioning based on space-time coordination(SPKM), which simplifies the problem of coordinated charging of multiple UAVs and maximizes energy. Using the efficiency and charging success rate, the optimal charging trajectory can be found under the constraint that the node will not starve to death due to power shortage. Finally, a simulation comparison experiment is carried out with the existing UAV charging scheduling strategy. UOCS achieves the optimal node survival rate with low algorithm complexity.

Theoretical approaches were applied to study the effect of magnetic field and heat transfer on the flow of blood plasma through an asymmetric arterial segment. The plasma was considered to be unsteady, laminar and an incompressible fluid through non-uniform arterial segment in a two-dimensional flow. Axial velocity, pressure gradient, stream function and pressure shift per wavelength were evaluated in blood plasma flow in arteries by use of coupled linear partial differential equations, solved with the help of Finite difference method. The corresponding initial and boundary conditions were obtained by discretizing the flow channel. The effect of magnetic field on blood plasma in arteries was determined by creating a magnetic field gradient through the application of a varying strength of magnetic field on the flow. Heat transfer characteristics due to applied magnetic field and viscosity of blood was obtained by use of linear partial differential equations to determine varying temperature conditions in heat transfer characteristics. Numerical results for velocity profiles, magnetic profiles and temperature profiles were obtained to characterize blood plasma viscosity by use of various non-dimensional parameters. The results were graphically presented using MATLAB software. The results obtained helped in analyzing theoretically the effects of magnetic field and heat transfer in arterial plasma flow.

The Internet of Things (IoT) is experiencing widespread adoption across industry sectors ranging from supply chain management to smart cities, buildings, and health monitoring. However, most software architectures for IoT deployment rely on centralized cloud computing infrastructures to provide storage and computing power, as cloud providers have high economic incentives to organize their infrastructure into clusters. Despite these incentives, there has been a recent shift from centralized to decentralized architecture that harnesses the potential of edge devices, reduces network latency, and lowers infrastructure cost to support IoT applications. This shift has resulted in new edge computing architectures, but many still rely on centralized solutions for managing applications. A truly decentralized approach would offer interesting properties required for IoT use cases. To address these concerns, we introduce a decentralized architecture tailored for large scale deployments of peer-to-peer IoT sensor networks and capable of run-time application migration. The solution combines a blockchain consensus algorithm and verifiable random functions to ensure scalability, fault tolerance, transparency, and no single point of failure. We build on our previously presented theoretical simulations with many protocol improvements and an implementation tested in a use case related to monitoring a Slovenian cultural heritage building located in Bled, Slovenia.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

ST-segment elevation myocardial infarction (STEMI), a major cause of mortality worldwide, has been shown through epidemiological studies to have a relationship with short-term exposure to air pollutants; however, the association between air pollutants and the outcome of STEMI has not been well studied. The aim of this study was to estimate the impact of air pollutants on the outcomes of STEMI. Data on particulate matter <2.5 μm (PM2.5), <10 μm (PM10), nitrogen dioxide (NO2), and ozone (O3) at each of the 11 air monitoring stations in Kaohsiung City were collected between January 1, 2012, and December 31, 2017. Medical records of non-trauma patients aged > 20 years who had visited the ED with a principal diagnosis of STEMI were extracted. The primary outcome measure was in-hospital mortality. After adjusting for potential confounders and meteorological variables, we found that an increase in the interquartile range (IQR) in NO2 was associated with an elevated risk of in-hospital mortality in patients with STEMI. Moreover, during the warm season, an IQR increase in NO2 corresponded to a higher risk of in-hospital mortality in patients with STEMI on lag 3 (OR=3.266; 95% CI:1.203–8.864, p=0.02). Conversely, an IQR increase in PM10 was associated with an increased risk of in-hospital mortality in patients with STEMI on lag 3 (OR=2.792; 95%CI:1.115–6.993, p=0.028) during the cold season. Our study suggests that exposure to NO2 (during warm season) and PM10 (during cold season) may contribute to a higher risk of poor prognosis in patients with STEMI.

In order to perform multi-degree-of-freedom motion measurements of marine machinery such as ship-borne mechanical platform in an absolute environment without a reference, absolute measurement methods using acceleration sensors and tilt gyroscopes are typically employed. However, due to the influence of wave forces on ship-borne mechanical platform, the coupling between different degrees of freedom can cause mutual interference, resulting in significant sensor measurement disturbances that make efficient computation and real-time analysis challenging. Specifically, when ship-borne mechanical platform swings, the proof mass of the acceleration sensor produces an undesirable signal output in the vertical direction, which leads to imprecise acceleration integration, thereby affecting accurate motion collection and posture estimation. To address these challenges, by analyzing the influence of the inclination angle of the ship-borne mechanical platform on the sensor measurement, and using the working principle of the acceleration sensor and angle sensor, a correction method for the motion measurement of the ship-borne mechanical platform based on multi-sensor fusion is proposed. In this article, we first analyze the influence of inclination angle on the integral effect in the heave direction. Then the configuration using four groups of acceleration sensors to correct the integral effect is proposed. Finally, the optimal inclination angle is determined through Kalman filtering based on the measured value of angle sensors and estimated values from the acceleration sensor sets. Experiments have proved that the average error of the corrected heave displacement signal is 25.34 mm, which is better than the integral displacement signal of a single acceleration sensor. At the same time, the acceleration sensor is used to calculate the roll angle and pitch angle of the ship-borne mechanical platform, and combined with the angle sensor signal to perform Kalman filtering, which filters out the errors caused by the shaking and instability of the mechanical platform, and can more accurately estimate the true inclination of the platform. Therefore, this method can enhance the precision and accuracy of the ship-borne mechanical platform motion signal acquisition, providing more valuable experimental data for research in marine engineering and related fields.

Objective: To explore the application effect of Atropine injection combined with nursing intervention on the interventional treatment of PATENTS with ST-segment elevation myocardial infarction. Methods: A total of 60 patients with ST-segment elevation myocardial infarction treated in our hospital from January 2022 to January 2023 were selected as the research objects. According to different nursing methods, they were divided into conventional group (n = 30) and systematic group (n = 30), both groups were treated with percutaneous coronary intervention (PCI). The conventional group received routine nursing before and after operation. On the basis of routine nursing, systematic nursing cooperation was given in the system group. The time of opening infarct vessels, the incidence of total adverse reactions during interventional treatment, mortality, success rate of treatment, improvement of cardiac function and length of hospital stay were compared between the two groups. Results: The time of opening infarct vessel in system group was significantly better than that in routine group (P < 0.05). The total adverse reaction rate in system group was significantly lower than that in routine group (P < 0.05); The mortality of routine group was significantly higher than that of system group (P < 0.05). The success rate of system group was significantly higher than that of routine group (P < 0.05); The number of patients with improved cardiac function and length of hospital stay in system group were significantly better than those in routine group (P < 0.05). Conclusion: Good intraoperative cooperation and nursing is an important guarantee for patients with ST-segment elevation myocardial infarction, which can effectively reduce the occurrence of adverse reactions during interventional treatment, improve the success rate of treatment, and reduce the death of patients during interventional treatment.

Myocilin is an enigmatic glaucoma-associated glycoprotein whose biological role remains incompletely understood. To gain novel insight into its normal function, we used transposon-mediated transgenesis to generate the first zebrafish line stably overexpressing myocilin [Tg(actb1:myoc-2A-mCherry)]. qPCR showed an approximately four-fold increased myocilin expression in transgenic zebrafish embryos (144 hpf). Adult (13 months old) transgenic animals displayed variable and age-dependent ocular anterior segment alterations. Almost 60% of two-years old male, but not female, transgenic zebrafish developed enlarged eyes with severe asymmetrical and variable abnormalities in the anterior segment, characterized by corneal limbus hypertrophy, and thickening of the cornea, iris, annular ligament and lens capsule. The most severe phenotype presented small or absent ocular anterior chamber and pupils, due to iris overgrowth along with dysplastic retinal growth and optic nerve hypertrophy. Immunohistochemistry revealed increased presence of myocilin in most altered ocular tissues of adult transgenic animals, as well as signs of retinal gliosis, and expanded ganglion cells and nerve fibers. The preliminary results indicate that these cells contributed to retinal dysplasia. Visual impairment was demonstrated in all old male transgenic zebrafish. Transcriptomic analysis of the abnormal transgenic eyes identified disrupted expression of genes involved in lens, muscular and extracellular matrix activities, among other processes. In summary, the developed transgenic zebrafish provides a new tool to investigate this puzzling protein and provides evidence for the role of zebrafish myocilin in ocular anterior segment and retinal biology, through the influence of extracellular matrix organization and cellular proliferation.

Anterior segment dysgenesis (ASD) encompasses a wide spectrum of developmental abnormalities of the anterior ocular segment, including congenital cataract, iris hypoplasia, aniridia, iridocorneal synechiae, as well as Peters, Axenfeld, and Rieger anomalies. Here, we report a large five-generation Caucasian family exhibiting atypical syndromic ASD segregating with a novel truncating variant of FOXC1. The family history is consistent with highly variable autosomal dominant symptoms including isolated glaucoma, iris hypoplasia, aniridia, cataract, hypothyroidism, congenital heart anomalies, and cystic kidney disease. Whole exome sequencing revealed a novel variant [c.313_314insA; p.(Tyr105*)] in FOXC1 that disrupts the alpha-helical region of the DNA-binding forkhead box domain. In vitro studies using a heterologous cell system revealed aberrant cytoplasmic localization of FOXC1 harboring the Tyr105* variant, likely precluding downstream transcription function. Meta-analysis of the literature highlighted the intrafamilial variability related to FOXC1 truncating alleles. This study highlights the clinical variability in ASD and signifies the importance of combining both clinical and molecular analysis approaches to establish a complete diagnosis.

The aim of this paper is to create a sensor model based on optical crystal fibers (PCF). The aim of this model is to find and identify zinc cadmium. This thesis looked at three different categories of concentrations. For sensor architecture, PCF was generated using single-mode fiber-to-end split fusion (SM-PCF-SM). In this experiment, a specific wavelength spectrum was used to alter the concentration of materials covering the fiber in order to demonstrate the fiber's sensing capability. The 550nm wavelength has been used as the optical source for the fiber. The change in the output power of the external light was monitored and changes were observed for each concentration of the concentrations around the fiber. It has been found that the fiber is sensitive to small changes in concentrations. The absorption of the fiber has been calculated for the incoming capacity, as well as the losses in the capacity outside the fiber.

4-(thiazol-2-yldiazenyl)phenol (L₁) and 2-((4-hydroxyphenyl) diazenyl)-5-nitrophenol (L₂) based on azo phenol were synthesised and used as selective colorimetric sensor for CN^- and AcO⁻ ion in DMSO/H₂O-HEPES (v/v; 1:1, pH–7.3 ± 0.2) and showed good sensitivity with large red shifts and nanomolar detection limit for CN^- and AcO^- ion. The stoichiometry of L₁ with CN⁻/AcO⁻ ion was found to be 1:1 and L₂ with CN⁻/AcO⁻ ion was found to be 1:2. Binding constant for L₁+ CN⁻, L₁ + AcO⁻, L₂ + CN⁻ and L₂ + AcO⁻ were calculated by B-H plot as 1.6 × 10³, 8.0 × 10², 8.4 × 10³ and 1.7 × 10² respectively. L₂ showed high selectivity towards CN⁻ ion with low detection limit of 81 nM and large binding constant. In addition, ¹H NMR titration and DFT studies also supported the deprotonation mechanism of receptors in the presence of selective anions.

Phosphors based on magnesium titanate activated with Mn⁴⁺ ions are of great interest because, when excited with blue light, they display a strong red-emitting luminescence. They are characterized by a luminescence decay which is strongly temperature dependent in the range from 0 to 80 °C, making these materials very promising for temperature sensing in the biochemical field. In this work the optical and thermal properties of the luminescence of Mg₂TiO₄ are investigated for different Mn⁴⁺ doping concentrations. The potential of this material for temperature sensing is demonstrated by fabricating a fiber optic temperature microsensor and by comparing its performance against a standard resistance thermometer. The response of the fiber optic sensor is exceptionally fast, enabling monitoring of temperature fluctuation in subsecond time domain.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

The 20–60-μm axon initial segment (AIS) is proximally located at the interface between the axon and cell body. AIS has characteristic molecular and structural properties regulated by the crucial protein, ankyrin-G. The AIS contains a high density of Na+ channels relative to the cell body, which allows low thresholds for initiation of action potential (AP). Molecular and physiological studies have shown that the AIS is also a key domain for the control of neuronal excitability by homeostatic mechanisms. The AIS has high plasticity in normal developmental processes and pathological activities such as injury, neurodegeneration, and neurodevelopmental disorders (NDDs). In the first half of this review, we provide an overview of the molecular, structural, and ion-channel characteristics of AIS, AIS regulation through axo-axonic synapses, and axo-glial interactions. In the second half, to understand the relationship between NDDs and AIS, we discuss the activity-dependent plasticity of AIS, the human mutation of AIS regulatory genes, and the pathophysiological role of the abnormal AIS in the NDD model animals and patients. We propose that AIS may provide a potentially valuable structural biomarker in response to abnormal network activity in vivo as well as a new treatment concept at the neural circuit level.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

AYUMI EYE is an accelerometer-based gait analysis device that measures the 3D accelerations of the human trunk. This study investigated the measurement accuracy of the AYUMI EYE as hardware as well as the accuracy of the gait cycle extraction program via simultaneous measurements using AYUMI EYE, a ground reaction force (GRF), and an optical motion capture system called VICON. The study was conducted with four healthy individuals as participants. The gait data were obtained by simulating four different patterns for three trials each: normal walking, anterior-tilt walking, hemiplegic walking, and shuffling walking. The AYUMI EYE and VICON showed good agreement for both the acceleration and displacement data. The durations of subsequent stride cycles calculated using the AYUMI EYE and GRF were in good agreement based on the calculated cross-correlation coefficients (CCs) with an r value of 0.896 and p-value less than 0.05, and their accuracies for these results were sufficient.

Sensor fusion algorithms and models have been widely used in recent times. Although research evidence has informed the use of sensor fusion models in diverse applications, there is room for improvement, especially in home-based health monitoring applications which require less supervision and technical knowledge of users. The present work compares data mining-based fusion software packages such as RapidMiner Studio, Anaconda, Weka, and Orange, and proposes a data fusion framework suitable for in-home applications. 574 privacy-friendly (binary) images and 1,722 datasets gleaned from thermal and Radar sensing solutions respectively, were fused using the software packages on instances of homogeneous and heterogeneous data aggregation. Experimental results indicated that the proposed fusion framework achieved an average Classification Accuracy of 84.7% and 95.7% on homogeneous and heterogeneous datasets respectively, with the help of data mining and machine learning models such as Naïve Bayes, Decision Tree, Neural Network, Random Forest, Stochastic Gradient Descent, Support Vector Machine, K-Nearest Neighbours and CN2 induction. Further evaluation of the sensor data fusion framework based on cross validation of features indicated average values of 94.4% for Classification Accuracy, 95.7% Precision and 96.4% for Recall.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Detection of human movement requires lightweight, flexible systems to detect mechanical parameters (like strain and pressure) not interfering with user activity, and that he/she can wear comfortably. In this work we address such multifaceted challenge with the development of smart garments for lower limb motion detection, like a textile kneepad and anklet in which soft sensors and readout electronics are embedded for detecting movement of the specific joint. Stretchable capacitive sensors with a three-electrode configuration are built combining conductive textiles and elastomeric layers, and distributed at knee and ankle. They show an excellent behavior in the ~30% strain range, hence the correlation between their responses and the optically tracked Euler angles is allowed for basic lower limb movements. Bending during knee flexion/extension is detected, and it is discriminated from any external contact by implementing in real time a low computational algorithm. The smart anklet is designed to address joint motion detection in and off the sagittal plane. In this work, ankle dorsi/plantar flexion, adduction/abduction, and rotation are retrieved. Both smart garments show a high accuracy in movement detection, with a RMSE less than 4° in the worst case.

Glass has emerged as a highly versatile substrate for various sensor and MEMS packaging applications, including electromechanical, thermal, optical, biomedical, and RF devices, due to its exceptional properties such as high geometrical tolerances, outstanding heat and chemical resistance, excellent high-frequency electrical properties, and the ability to be hermetically sealed. In these applications, Through-Glass-Via (TGV) plays a vital role in manufacturing and packaging by creating electrical interconnections through glass substrates. This paper provides a comprehensive summary of the research progress in TGV fabrication along with their integrations, including through-via formation and metallization. The paper also reviews the significant qualification and reliability achievements obtained by the scientific community for TGV. Additionally, the paper summarizes the application of TGV technology in various sensors.

Cancer is a common illness with a high mortality. Compared to traditional technologies, biomarkers detection, with low cost and simple operation, has higher sensitivity and faster speed in early screening and prognosis of cancer. Therefore, extensive research has been focused on the development of biosensors and the construction of sensing interfaces. Molybdenum disulfide (MoS2) is a promising two-dimensional (2D) nanomaterial, whose unique adjustable bandgap shows excellent electronic and optical properties in the construction of biosensor interfaces. It not only has the advantages of high catalytic activity and low manufacturing costs, but also can further expand the application of hybrid structures by different functionalization, and is widely used in various biosensors fields. Herein, the application of electrochemical and optical sensing platforms based on MoS2 in the detection of cancer biomarkers was comprehensively reviewed. Firstly, the structure and preparation method of MoS2 were introduced, and its applicable characteristics in the field of biosensors were explored. Secondly, we comprehensively reviewed the recent construction and application of sensing platform based on MoS2 in the field of cancer biomarkers detection in both electrochemical and optical aspects. The prime characteristics and application performances of MoS2 and its composites were emphasized. Additionally, we also involved some other types of biosensors based on MoS2. Finally, we summarized the challenges and development prospects of MoS2 in the application of cancer biomarkers detection, and provided some insights for the application potential of this kind of emerging nano-materials in a broader field.

Programmable Object Interfaces are increasingly intriguing researchers because of their broader applications, especially in the medical field. In Wireless Body Area Network (WBAN), for example, the patients’ health can be monitored using clinical nano sensors. Exchanging such sensitive data requires a high level of security and protection against attacks. To that end, the literature is rich with security schemes that include the advanced encryption standard, secure hashing algorithm, and digital signatures that aim to secure the data exchange. However, such schemes elevate the time complexity rendering the data transmission slower. Cognitive Radio technology with a medical body area network system involves communication links between WBAN gateways, server and nano sensors rendering the entire system vulnerable to security attacks. In this paper, a novel DNA-based encryption technique is proposed to secure medical data sharing between sensing devices and central repositories. It has less computational time throughout authentication, encryption, and decryption. Our analysis of experimental attack scenarios shows that our technique is better than its counterparts.

This paper proposes the localisation of room occupants in home environments using Unobtrusive Sensing Solutions (USSs). The ability to localise room occupants in home environments can help in the objective monitoring of sedentary behaviour. While wearable sensors can provide tangible information on health and wellness, they have battery life issues and the inability to perform prolonged monitoring. This work uses heterogeneous USSs in the form of an Infrared Thermopile Array (ITA-64) thermal sensor and a Multi-Chirp Frequency Modulated Continuous Wave Mono-pulse (MC-FMCW-M) Radar sensor to monitor room occupants. Digital filters and background subtraction algorithms were used to process the thermal images gleaned from the ITA-64 thermal sensors. The MC-FMCW-M Radar sensor used multi-chirp and Doppler shift principles to estimate the exact location of the targeted room occupants. The estimated distances from the Radar Sensor were compared with ground truth values. Experimental results demonstrated the ability to identify thermal blobs of occupants present in the room at any particular time. Data analyses indicated no significant difference (p = 0.975) and a very strong positive correlation (r = 0.998) between the ground truth distance values and those obtained from the Radar Sensor.

Background: As a relatively high number of ST-segment elevation myocardial infarction (STEMI) patients develop major adverse cardiovascular events (MACE) following percutaneous coronary intervention (PCI), our aim was to determine the significance, and possible predictive value of QRS complex width and ST-segment elevation. Methods: Our patient sample included 200 PCI-treated STEMI patients, which were divided into two groups, based on the duration of symptoms: (I) less than 6 hours, and (II) 6-12 hours. For every patient, ECG was performed at 6 different time points. Long-term follow-up lasted 6 years from the STEMI onset. Statistical analysis was performed. Results: The mean age was 60.6±11.39 years, and 142 were male. Wider QRS complex, more pronounced ST-segment elevation, and more frequently absent ST-segment resolution were more common in the second group. Presentation of MACE was more frequent in this group. An increase of pre-PCI QRS complex width by 1 msec increases the risk of 6-year MACE by 3%, and an increase in pre-PCI ST-segment elevation by 1mm increases the risk of 6-year MACE by 3.26 times. Conclusion: To the best of our understanding, this study represents a pioneer research that utilized these ECG elements in the context of predicting a 6-year MACE. A wider QRS complex and a more pronounced ST-segment elevation were associated with longer total ischemic time. More research is needed to confirm these findings.

This paper proposes training improvement methods of artificial neural networks (ANN) trajectory predictors. First, a dynamic power system time-series trajectory is split into several different segments to simplify the original ANN training problem. Moreover, the time-derivative of the trajectory is included to obtain an augmented loss function. Compared to previous studies which mainly focused on increasing the prediction accuracy, the aim of these novel techniques is to reduce the computational burden where the ANN output performance is still acceptable. The effectiveness of the developed methods is validated based on the WSCC three-machine nine-bus and IEEE 39-bus system models. The mean absolute error (MAE) and trajectory prediction results are analyzed, in which the numbers of neurons, hidden layers, and training epochs are constrained during the ANN training process. Rotor-angle difference between generators and the system frequency are investigated as the dynamic trajectories of the power system models. It is revealed that when the ANN architecture and epochs are constrained, the MAE results can be reduced, and the ANN training results can better reflect the original trajectory using the improvement approaches.

The purpose of the study was to identify factors characterizing a decrease in LV global systolic function in patients with ST-segment elevation myocardial infarction (STEMI) after revascularization using cardiac magnetic resonance imaging (MRI)-based ischemic injury pattern and laboratory parameters sensu left ventricular global systolic function. A total of 109 STEMI patients were examined. The patients underwent contrast-enhanced cardiac MRI with a 1.5 Tesla GE SIGNA Voyager (GE HealthCare, USA) on the 7th-10th days from the onset of the disease. According to cardiac MRI analysis, the patients were divided into the following groups with regard to left ventricular ejection fraction (LVEF) values: group 1 – patients with LVEF ≥50%; group 2 – patients with mildly reduced LVEF 40-49%; group 3 – patients with low LVEF <40%. A predominance of most parameters of the ischemic injury pattern was noted in patients with mildly reduced and low LVEF versus patient group with LVEF ≥50%. Some risk factors for a decrease in LVEF <50% systolic function in STEMI patients after revascularization were revealed: male gender; time from the onset of the anginal attack to revascularization; coronary artery status; several LV parameters; ischemic injury characteristics; natriuretic peptide and troponin I levels.

Large Language Models (LLMs) have proved significant proficiency when comes to code generation especially in Structured Query Language (SQL) for databases and recent successful Text-to-SQL method involves fine-tuning pre-trained LLMs for SQL generation tasks. Transforming natural language text into SQL queries, has been attempted to solve with various learning techniques including Few-shot learning[1], fine tuning. In this paper we propose Supervised fine-tuning (SFT) as a better alternative for learning technique for text-to-SQL generation task using Code-Llama that pushes state of art accuracy on spider test suite to 89.6% on dev set which represent first instance of surpassing the earlier best-in-class with 5.5% higher score and 86.8% of exact match accuracy on dev set. Furthermore, we demonstrate that properly prompted LLM along with SFT provides far fewer hallucinations and much more robust LLM that can be used as a general tool for any text-to-SQL generation use case.

About a decade ago, active optical crop canopy sensors are being used to manage in-season variable nitrogen (N) fertilization in cornfields to match the plant demand that occurs mid season, increasing the efficiency compared to broadcast N applications. There were also initiatives of using ultrasonic sensors to measure plant height on-the-go for N application and crop water demand estimation, but no studies have integrated the optical, ultrasonic and canopy temperature for crop water stress assessment. The objective of this chapter is to evaluate the crop water status using infrared thermometry integrated with optical and ultrasonic sensors. Specifics objectives are: (i) evaluate the corn canopy temperature under different previous crop, N rates and irrigation levels; (ii) test a procedure for water stress assessment in commercial cornfields using the integration of sensors, (iii) correlate plant based sensor measurements (N status, plant height and canopy temperature) with grain yield, soil attributes and detailed topographical features, and (iv) study the spatial dependence of canopy temperature. This study was conducted in one small plot study area and on three producer’s fields in 2010. The small plot experiment consisted of two irrigation levels (70 and 100% of evapotranspiration – ET), two previous crop schemes (corn after corn – CC and corn after soybeans – CS), and four N rates (0, 75, 150, 225 kg N ha^-1). Canopy temperature, optical reflectance and plant height was measured from R2 until R6 in the small plots. At the producer’s fields, three long strips across center pivots were used to have a non-limited N and water crop and then continuous georeferenced sensors measurements were taken during side-dress (V11 growth stage) in about 10 hectares in each field. In the small plot study the crop canopy temperature was influenced by the irrigation levels and N rates. The procedure proposed could be used to identify zones in the producer’s field where water stress can be a yield limiting factor other than N derived. Inside the zones considered that water stress played a major whole, there were low correlations between plant height, plant N status and canopy temperature, indicating that the canopy temperature had more influence from water stress than vegetation cover. Concave and lower elevation areas had higher yields compared to convex and high elevation, showing that the detailed elevation mapping can be beneficial to delineate stables zones that possibly could be used in variable irrigation systems. The spatial dependence of canopy temperature was over 65 meters across producers’ sites, showing that the commercial high clearance applicator’s swath width was adequate to obtain accurate maps. The integration of plant N status, plant height and canopy temperature was beneficial to detect water stressed zones in the field. Opportunities can be foresee also for on-the-go N fertilization using integration of these sensors because is likely that water stress can be confounded with different N supply during the growing season and in different zones in the field.

In this work, an energy-saving smart light controlling system has been proposed that can main-tain the desired intensity of light in a room automatically. Unlike the conventional light control system, the proposed system splits a large room into several zones and analyzes the light inten-sity of each zone; hence, the controlling unit adjusts the light intensity to the desired level. The main controlling unit consists of a light sensor, a motion sensor, a relay with a driver unit, an LCD display, etc. for controlling light efficiently to reduce the power waste. The sensors meas-ure the intensity of light, based on the standard light intensity data chart the controller units make a decision how many light bulbs are needed to be switched ON/OFF in a particular zone. Moreover, the system automatically switched-OFF all light bulbs when there is nobody in the room. Proteus design suite 8.0 is used to design and simulation of the proposed system. Moreo-ver, the PCB layout is designed using ExpressPCB version 7.5.0. The proposed system is capable of minimizing the power loss by up to 44% in comparison to the conventional light manage-ment system.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

As the amount of sensor data made available online increases, it becomes more difficult for users to identify useful datasets. Semantic web technologies improve discovery with meaningful ontologies, but the decision of suitability remains with the users. The GEO label provides a visual summary of the standardised metadata to aid users in this process. This work presents novel rules for deriving the information for the GEO label's multiple facets, such as user feedback or quality information, based on the Semantic Sensor Network Ontology and related ontologies. It enhances an existing implementation of the GEO label API to generate labels for resources of the Semantic Sensor Web. The prototype is deployed to serverless cloud infrastructures. We find that serverless GEO label generation is capable of handling two evaluation scenarios for concurrent users and burst generation. More real-world semantic sensor descriptions and an integration into large scale discovery platforms are needed to develop the presented solutions further.

In this paper analyses the characteristic of EM waves propagation in structured environment to identify the signal interference by the structure, and suggests the EM waves attenuation model considering the distance and penetration loss by the structure. The range sensor based on electromagnetic(EM) waves attenuation along to the distance showed the precise distance estimation with high resolution depending on the distance. However, it is hard to use in structured environments due to the lack of consideration of the EM waves attenuation characteristics in the structured underwater environment. In this paper, EM waves propagation characteristic and signal interference effects by the structures were analyzed, and the EM waves distance-attenuation model in structured environment was suggested with sensor installation guideline. The EM waves propagation characteristics and proposed sensor model were verified by the several experiments, and the localization result in structured environment showed the more reliable performance.

Study design: Retrospective observational study. Objectives: To evaluate the change in adjacent segment disease (ASD) after hybrid dynamic stabilization with Dynesys-Transition-Optima (DTO). Methods: In 2012–2020, 115 lumbar spinal stenosis patients with spondylolisthesis re-fractory to nonsurgical management received hybrid dynamic stabilization with DTO system in a single medical center from a single neurosurgeon. After excluding those who did not receive L3–L4 dynamic stabilization and L4–L5 transforaminal lumbar interbody fusion fixation and those with incomplete postoperative data (n = 84), the 31 patients studied received follow-up vis-its at 6, 12 and 24 months postoperatively. Radiological assessment applied at the L2–L3, L3–L4 and L5–S1 segments separately included disc height, listhesis distance and angular change while in motion. Implant failure and screw loosening sign were both documented. Results: In the L3–L4 segment, the listhesis distance appeared 1 year after the operation; however, alterations in other segments showed at 6 months. At 2 years, the L3–L4 segment showed significantly less increase in listhesis distance and relatively less disc height reduction than other segments. In motion an-gular change, only the L3–L4 segment had a significant decrease at 2 years. Only the L3–L4 seg-ment maintained negative growth over 2 years in time-dependent assessment of motion angular change. Conclusions: In our study, disc height decreased, listhesis distance increased less and ASD changed later at the index level than the L2–L3 and L5–S1 levels. Angular change was re-duced at the index level while in motion. Although ASD was not significantly prevented, index level degeneration was both minor

A Mw7.8 earthquake struck Turkey on February 6, 2023, causing severe casualties and economic losses. This paper investigates the characteristics of strong ground motion and seismogenic fault of the earthquake. We collected and processed the strong ground motion records of 379 stations using Matlab, SeismoSignal and Surfer software, and obtained the peak ground acceleration (PGA) contour map. We analyzed the near-fault effect, the fault locking segment effect and the trampoline effect of the earthquake based on the spatial distribution of PGA, the fault geometry and slip distribution. We found that the earthquake generated a very strong ground motion concentration effect in the near-fault area, with the maximum PGA exceeding 2000cm/s2. However, the presence of fault locking segments influenced the spatial distribution of ground motion, resulting in four significant PGA high-value concentration areas at a local dislocation, a turning point and the end of the East Anatolian Fault. We also revealed for the first time the typical manifestation of the trampoline effect in this earthquake, which was characterized by a large vertical acceleration with the positive direction significantly larger than the negative direction. This paper provides an important reference for understanding the seismogenic mechanism, damage mode, characteristics and strong earthquake law of Turkey earthquake.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

We present the hardware of a cheap multi-sensor magnetometric setup, where a relatively large set of magnetic field components is measured in several positions by calibrated magnetoresistive detectors. The setup is developed to map the (inhomogeneous) field generated by a known magnetic source, which is measured and then discerned from the background (homogeneous) geomagnetic field. The data output from this hardware can be successfully and reliably used to retrieve the position and orientation of the magnetic source with respect to the sensor frame, together with the orientation of the frame with respect to the environmental field. Possible applications of the setup are briefly discussed, and a synthetic description of the methods of data elaboration and analysis is provided.

In this study, a flexible strain sensor is devised using corrugated poly(3-hexylthiophene) (P3HT) thin film. In the previous studies, the P3HT-based photoactive thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to relatively more brittle thin film constituent—poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS) conductive thin film as a bottom electrode. To address this issue, it is aimed to design mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to optimize design of the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS thin film affect the optical and electrical properties. Also, pre-strain effect on light absorptivity of the corrugated P3HT-based thin films was studied. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and DC voltage strain sensing capability was validated. As a result, flexible strain sensor exhibited tensile strain sensing range up to 5% at frequency up to 15 Hz with maximum gage factor ~7.

People counting applications have been used in diverse applications. The ability and accuracy of thermal imaging over conventional image cameras has led to the implementation of thermal cameras in people counting applications. This paper present a thermal people counting smart glass windows. The people counting application would be remotely monitored from a single centralized PC station as it’s connected to a multiplex of mass monitoring of 20 thermal camera, all embedded into different glass windows. The thermal cameras would then be able to detect body temperatures of all individuals who pass through any of the camera range and also count the numbers of people who passed through the camera range. The data gotten can then be further utilized in various ways, example is in the control of air conditioning and lightening.

This paper compares two types of microfluidic sensors that are designed for operation in ISM bands at microwave frequencies of 2.45 GHz and 5.8 GHz. In the case of the first sensor, the principle of operation is based on the resonance phenomenon in a microwave circuit filled with a test sample. The second sensor is based on the interferometric principle and makes use of the superposition of two coherent microwave signals, where only one of them goes through a test sample. Both sensors are monolithic structures fabricated using low temperature co-fired ceramics (LTCC). The LTCC-based microwave-microfluidic sensor properties are examined and compared by measuring their responses for various concentrations of two types of test fluids: one is a mixture of water/ethanol, and the other is dopamine dissolved in a buffer solution. The experiments show a linear response for the LTCC-based microwave-microfluidic sensors as a function of the concentration of the components in both test fluids.

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

Among the five human senses, light, sound, and force perceived by eye, ear, and skin, respectively are physical actions, and therefore can be easily measured and expressed as objective, univocal, and simple digital data with physical quantity. However, taste and odor molecules perceived by tongue and nose are chemical actions, it has been difficult to express them as objective and univocal digital data, since no reference chemicals can be defined. Therefore, while the recording, saving, transmitting to remote locations, and replaying human visual, auditory, and tactile information as digital data in digital devices has been realized (this series of data flow is defined as DX (digital transformation) in this review), the DX of human taste and odor information is not yet in the realization stage. Particularly, since there are at least 400,000 types of odor molecules and an infinite number of complex odors that are mixtures of these molecules, it has been considered extremely difficult to realize "human olfactory DX" by converting all odors perceived by the human olfaction into digital data. In this review, we discuss the current status and future prospects of the development of "human olfactory DX," which we believe can be realized by utilizing odor sensors that employ the olfactory receptors (ORs) that support human olfaction as sensing molecules (i.e., human OR sensor).

Classical and optimal control architectures for motion mechanics with fusion of noisy sensors use different algorithms and calculations to perform and control any number of physical demands, to varying degrees of accuracy, precision, and cost. Their performances are tested for the purpose of comparison through the means of a Monte Carlo simulation that simulates how different parameters might vary under noise, representing real-world imperfect sensors. We find that improvements in one figure of merit often come at a cost in the performance in the others, especially depending on the presence of noise in the system sensors. If sensor noise is negligible, open-loop optimal control performs the best. However, in the overpowering presence of sensor noise, using a control law inversion patching filter performs as the best replacement, but has significant computational strain.

Landslides are a global and frequent natural hazard, affecting many communities and infrastructure networks. Technological solutions are needed for long-term, large-scale condition monitoring of infrastructure earthworks, or natural slopes. However, current instruments for slope stability monitoring are often costly, require a complex installation process and/or data processing schemes, or have poor resolution. Wireless sensor networks comprising low-power, low-cost sensors have been shown to be a crucial part of landslide early warning systems. Here, we present the development of a novel sensing approach that uses linear arrays of three-axis accelerometers, used for monitoring soil deformation. By combining these deformation measurements with depth-resolved temperature measurements, we can link our data to subsurface thermal-hydrological regimes where relevant. In this research, we present a configuration of cascaded I2C sensors that (i) have ultra-low power consumption and (ii) enable an adjustable probe length. From an electromechanical perspective, we developed a novel board-to-board connection method that enables narrow, semi-flexible sensor arrays and a streamlined assembly process. The low-cost connection method relies on a specific FR4 printed circuit board design that allows board-to-board press-fitting without using electromechanical components or solder connections. The sensor assembly is placed in a thin, semi-flexible tube (inner diameter 6.35 mm) that is filled with an epoxy compound. The resulting sensor probe is connected to a AA battery powered data logger with wireless connectivity. We characterize the system's electromechanical properties and investigate the accuracy of deformation measurements. Our experiments performed with probes up to 1.8 m long demonstrate long-term connector stability, as well as probe mechanical flexibility. Furthermore, our accuracy analysis indicates that deformation measurements can be performed with a 0.390 mm resolution and a 95% confidence interval of ±0.73 mm per meter of probe length. This research shows the suitability of low-cost accelerometer arrays for distributed soil stability monitoring. In comparison to emerging low-cost measurements of surface displacement, our approach provides depth-resolved deformation, which can inform about shallow sliding surfaces.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures. The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding. Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethane string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures.The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding.Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethan string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

How do sensor research and technologies grow over time? This paper applies the network analysis with a new computational approach to map the structure and evolution of sensor research and technologies over a 30-year time frame (1990-2020).The goal of this study is to analyze the evolution of sensor research for forecasting emerging scientific and technological trajectories. Results show that the scientific interaction within ecosystem (represented with networks) of sensor generates a co-evolution of scientific fields supporting the accelerated growth of different technological tra-jectories, such as: wireless sensors, fiber optic and optical sensors, gas sensors and biosensors. These results suggest main theoretical implications that explain the evolution of sensor research with critical aspects of innovation management to support R&D investments towards new technological trajectories having a high potential of growth.

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

Amebiasis is a disease caused by the unicellular parasite Entamoeba histolytica. In most cases, the infection is asymptomatic but when symptomatic, the infection can cause dysentery and invasive extraintestinal complications. In the gut, E.histolytica feeds on bacteria. Increasing evidences support the role of the gut microbiota in the development of the disease. In this review we will discuss the consequences of E.histolytica infection on the gut microbiota. We will also discuss new evidences about the role of the gut microbiota in regulating the resistance of the parasite to oxi-dative stress and its virulence.

A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

Autonomous driving vehicles rely on sensors for the robust perception of surroundings. Such vehicles are equipped with multiple perceptive sensors with a high level of redundancy to ensure safety and reliability in any driving condition. However, multi-sensor, such as camera, LiDAR and radar, systems bring up the requirements related to sensor calibration and synchronization, which are the fundamental blocks of any autonomous system. On the other hand, sensor fusion and integration have become important aspects of autonomous driving research and directly determine the efficiency and accuracy of advanced functions such as object detection and path planning. Classical model-based estimation and data-driven models are two mainstream approaches to achieving such integration. Most recent research is shifting to the latter, showing high robustness in real-world applications but requiring large quantities of data to be collected, synchronized, and properly categorized. To generalize the implementation of the multi-sensor perceptive system, we introduce an end-to-end generic sensor dataset collection framework that includes both hardware deploying solutions and sensor fusion algorithms. The framework prototype integrates a diverse set of sensors, such as cameras, LiDAR, and radar. Furthermore, we present a universal toolbox to calibrate and synchronize three types of sensors based on their characteristics. The framework also includes the fusion algorithms, which utilize the merits of three sensors , namely, camera, LiDAR and radar, and fuse their sensory information in a manner that is helpful for object detection and tracking research. The generality of this framework makes it applicable in any robotic or autonomous applications, also suitable for quick and large-scale practical deployment.

A laser-based hydrogen (H₂) sensor using wavelength modulation spectroscopy (WMS) was developed for contactless measurements of molecular hydrogen. The sensor uses a distributed feedback (DFB) laser to target the H₂ quadrupole absorption line at 2121.8 nm. The H₂ absorption line exhibits weak collisional broadening and strong collisional narrowing effects. Both effects were investigated by comparing measurements of the absorption linewidth with detailed models using different line profiles that include collisional narrowing effects. The collisional broadening and narrowing parameters were determined for pure hydrogen as well as for hydrogen in nitrogen and air. Performance of the sensor was evaluated and the sensor applicability for H₂ measurements in a range of 0- 10 %v of H₂ was demonstrated. A precision of 0.02 %v was achieved with 1 meter of absorption pathlength (0.02 %v∙m) and 1 s of integration time. For the optimum averaging time of 20 s a precision of 0.005 %v∙m was achieved. A good linear relationship between H₂ concentration and the sensor response was observed. A simple and robust transmitter-receiver configuration of the sensor allows in-situ installations in harsh industrial environments.

The development of a novel and simple inhibition biosensor array for detection of water pollutants based on immobilized bacteria is the main goal of this work. A series of electrochemical measurements (i.e. cyclic voltammograms) were carried out on screen-printed gold electrodes with three types of bacteria, namely Escherichia coli, Shewanella oneidensis, and Methylococcus capsulatus, immobilized via poly L-lysine. For comparison purposes, similar measurements were carried out on bacteria samples in solutions,; also optical measurements (fluorescence microscopy, optical density, and flow cytometry) were performed on the same bacteria in both liquid and immobilized forms. The study of the effect of heavy metal ions (lead), pesticides (atrazine) and petrochemicals (hexane) on DC electrochemical characteristics of immobilized bacteria revealed a possibility of pattern recognition of the above inhibition agents in aquatic environment.

Objective: To explore three novel fasting blood glucose (FBG)-based novel indicators, including FBG-to-albumin ratio (FAR), FBG-to-lymphocytes ratio (FLR), and FBG-to-hemoglobin ratio (FHR), in predicting prognosis and detecting metastasis for patients with pancreatic neuroendocrine neoplasms after resection. Materials and methods: A total of 178 pNEN patients underwent surgical resection were included in this study. Receiver operating characteristic (ROC) curves were used to evaluate the diagnosis values of FAR, FLR, and FHR, and the cut-off values were obtained for further analyses. Univariate and multivariate analyses were conducted to determine the independent predictors. The Kaplan-Meier method was used to evaluate the progression-free survival (PFS) and overall survival (OS) of the pNEN patients. Results: The optimal cut-off values of FAR, FLR, and FHR were 0.17, 2.85, and 0.028, respectively. As for PFS, the area under the curve (AUC) was 0.693 for FAR, 0.690 for FLR, and 0.661 for FHR, respectively. The AUC was 0.770, 0.692, and 0.715 accordingly for OS. The groups with lower FAR, FLR, and FHR were significantly associated with prolonged PFS and OS (p < 0.05). In patients with metastasis, the lower FAR group was correlated with significantly longer PFS and OS (p = 0.022 and 0.002, respectively). The FLR was an independent predictor of PFS in pNEN patients, and the FAR was a predictor of OS. FAR was an independent indicator of PFS in patients with metastasis. Conclusion: Preoperative FAR, FLR, and FHR are effective in predicting the prognosis of pNEN patients and detecting the synchronous metastases.

Objective: The current study aimed to delineate the relationship of furin with inflammation while cervical intraepithelial neoplasia progresses to cancer. Study Design:This cross-sectional study included 81 women who required colposcopic examinations. The study groups were formed based on pathological results: Group I included women with cervical intraepithelial neoplasia (CIN) I (n=30); Group II included women with CIN II-III (n=28); and Group III included women with cervical cancer (CC) (n=23). Furin, ki-67, and p16 levels were evaluated based on immunostaining intensity. The inflammatory indices were calculated parallel with the literature from routine blood samples retrieved within one week before the procedure. Results:Furin expression gradually increased from CIN I to CIN II-III and from CIN II-III to CC, respectively (p < .001, p = .005). The NLR, MLR, PLR, and SII were significantly higher in the CC group (p < .001). ROC curve analysis unveiled that NLR, MLR, PLR and SII predicted the presence of CC with a cutoff value of 2.39 for NLR (sensitivity: 91.3%, specificity: 63.8%, AUROC: 0.79, p < .001); a cutoff value of 0.27 for MLR (sensitivity: 78.3%, specificity: 72.4%, AUROC: 0.77, p = .009); a cutoff value of 123 for PLR (sensitivity: 100%, specificity: 41.4%, AUROC: 0.70, p = .04); and a cutoff value of 747 for SII (sensitivity: 69.6%, specificity: 90.7%, AUROC: 0.71, p = .014). Conclusion:Furin expression increased gradually in parallel to the severity of cervical intraepithelial neoplasia. The inflammatory indices were higher in the presence of CC and denoted good discrimination ability for predicting cervical cancer.

(1) Background: Little research has been done on professionals' perceptions of institutions and governments during epidemics. We aim to create a profile of physicians who feel they can raise public health issues with relevant institutions during a pandemic. (2) Methods: A total of 1285 Romanian physicians completed an online survey as part of a larger study. We used binary logistic regression to profile physicians who felt able to raise public health issues with relevant institutions; (3) Results: Five predictors could differentiate between respondents who tended to agree with the trust statement and those who tended to disagree: feeling safe at work during the pandemic, considering the financial incentive worth the risk, receiving training on the use of protective equipment, having the same values as colleagues, and enjoying work as much as before the pandemic; (4) Conclusions: Physicians who trust the system to raise public health issues with the appropriate institutions feel they share the same values as their colleagues, say they were trained in the use of protective equipment used during the pandemic, felt they were safe at work during the pandemic, enjoyed their work as much as before the pandemic, and felt the financial bonus justified the risk.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

in our increasingly interconnected world, sensor networks are critical in gathering and sending data for various applications, from environmental monitoring and industrial automation to healthcare and smart cities. However, as sensor networks expand in importance, so does the need to solve the multidimensional concerns of security, privacy, and forensics. This article explores the complex world of sensor network security, the delicate balance between data privacy and utility, and the emerging area of sensor network forensics. This article focuses on risk assessment of a network.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Over the last two decades, microfluidics has received significant attention from both academia and industry, and researchers report thousands of new prototype devices each year for use in a broad range of environmental, pharmaceutical, and biomedical engineering applications. While lab-on-a-chip fabrication costs have continued to decrease, the hardware required for monitoring fluid flows within microfluidic devices themselves remains expensive and often cost prohibitive for researchers interested in starting a microfluidics project. As microfluidic devices become capable of handling complex fluidic systems, low-cost, precise and real time pressure and flow rate measurement capabilities has become increasingly important. While many labs use commercial platforms and sensor, these solutions can often cost thousands of dollars and can be too bulky for on-chip use. Here we present a new inexpensive and easy -to-use piezoresistive pressure and flow sensor that can be easily integrated into existing on-chip microfluidic channels. The sensor consists of PDMS-Carbon black conductive membranes and uses an impedance analyzer to measure impedance change due fluid pressure. The sensor costs several orders of magnitude less than existing commercial platforms and can monitor local fluid pressures and calculate flow rates based on pressure gradient.

The objective of this paper is to present an electromagnetic sensor that generates pulse inductance [1], integrated on an Unmanned Aerial Vehicle (UAV) which complements the current technology in this area, adding equipment to the detection of landmines. The electromagnetic sensor developed, locates landmines deployed during armed conflicts, which daily kill innocent people, block economic and social development, hinder the displacement of people, causing serious social and economic problems for many years. Flights can be made over mined areas allowing the identification of the exact location of each land mine.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

The increase in the emission of greenhouse gases (GHG) is one of the most important world problems. Decreasing of GHG emission is a big challenge in the future. Transportation sector uses a significant part of petroleum production in the world and it leads to an increase in the emission of GHG. The result of this issue is that population of the world befoul environment of transportation system automatically. Electric Vehicles (EV) have a potentiality to solve a big part of the GHG emission and energy efficiency issues such as stability and reality of energy. The energy actors and their research team determine some targets for 2050; hence, they hope to decrease the world temperature to 6 °C in the best and 2 °C in the normal condition. Fulfillment of these scenarios needs suitable grid infrastructure but in most of the countries, the grid does not have a suitable background to apply those scenarios. In this paper, some problems about energy scenarios, energy storage systems, grid infrastructure and communication systems in supply and demand side of the grid and its solutions have been investigated.

Vehicle to vehicle (V2V) and Vehicle to infrastructure (V2I) or briefly V2X communications are the one of hot topics in automotive industry. Therefore, this situation is providing many advantages of connected vehicles and infrastructures which bring to human life. For instance, vehicles and road infrastructures which shares information with each other, provides a neat flow regulation, more ordered traffic flow and therefore jammed traffic dependent accident’s percentage will be decreased. On the other hand, security is the most important issue for these systems because the operation of V2X networks is completely dependent on uninterrupted and accurate information sharing. In the light of these information, in this paper we review security issues and current solution architectures. We also propose some open problems in this lively field.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

The authors present a novel sensing platform for a disposable electrochemical, non-enzymatic glucose sensor strip at physiological pH. The sensing material is based on dendritic gold nanostructures (AuNs) resembling feather branches, which are electrodeposited onto a Laser-scribed 3D-Graphene electrode (LSGE). The LSGEs were fabricated via a one-step laser scribing process on a commercially available polyimide sheet. This study investigates several parameters that influence the morphology of the deposited Au nanostructures and the catalytic activity towards glucose electro-oxidation. The electrocatalytic activity of AuNs-LSGE was evaluated using Cyclic Voltammetry (CV), Linear Sweep Voltammetry (LSV), and Amperometry, and was compared to commercially available carbon electrodes prepared under the same electrodeposition conditions. The sensor demonstrated good stability and high selectivity of the amperometric response in the presence of interfering agents, such as ascorbic acid, when a Nafion membrane was applied over the electrode surface. The proposed sensing strategy offers a wide linear detection range, from 0.5 to 20 mM, which covers normal and elevated levels of glucose in the blood, with a detection limit of 0.21 mM. The AuNs-LSGE platform exhibits great potential for use as a disposable glucose sensor strip for point-of-care applications, including self-monitoring and food management. Its non-enzymatic features reduce dependence on enzymes, making it suitable for practical and cost-effective biosensing solutions.

We analyze the information that can be retrieved from the tracking parameters produced by an innovative wearable eye tracker. The latter is based on a permanent-magnet marked corneal lens and by an array of magnetoresistive detectors that measure the magnetostatic field in several positions in the eye proximity. We demonstrate that, despite missing information due to the axial symmetry of the measured field, physiological constraints or measurement conditions make possible to infer complete eye-pose data. Angular precision and accuracy achieved with the current prototypical device are also assessed and briefly discussed. The results show that the instrumentation considered is suitable as a new, moderately invasive medical diagnostics for the characterization of ocular movements and associated disorders.

In this paper, a multi-mode waveguide-based optical resonator is proposed for an integrated optical refractive index sensor. Conventional optical resonators have been studied for single-mode waveguide-based resonators to enhance the performance, but mass production is limited owing to the high fabrication costs of nano-scale structures. To overcome this problem, we designed an S-bend resonator based on a micro-scale multi-mode waveguide. In general, multi-mode waveguides cannot be utilized as optical resonators, because of a performance degradation resulting from modal dispersion and an output transmission with multi-peaks. Therefore, we exploited the mode discrimination phenomenon using the bending loss, and the resulting S-bend resonator yielded an output transmission without multi-peaks. This phenomenon is utilized to remove higher-order modes efficiently using the difference in the effective refractive index between the higher-order and fundamental modes. As a result, the resonator achieved a Q-factor and sensitivity of 2.3x10³ and 52 nm/RIU, respectively, using the variational finite-difference time-domain method. These results show that the multi-mode waveguide-based S-bend resonator with a wide line width can be utilized as a refractive index sensor.

This paper reports the novel design of a touch mode capacitive pressure sensor (TMCPS) system with a wireless approach for a full-range continuous monitoring of ventricular pressure. The system consists of two modules: an implantable set and an external reading device. The implantable set, restricted to a 2x2 cm² area, consists of a TMCPS array connected with a dual-layer coil, for making a reliable resonant circuit for communication with the external device. The capacitive array is modelled considering the small deflection regime for achieving a dynamic and full 5-300 mmHg pressure range. In this design, the two inductive-coupled modules are calculated considering proper electromagnetic alignment, based on two planar coils and considering the following: 13.56 MHz frequency to avoid tissue damage and three types of biological tissue as core (skin, fat and muscle). The system was validated with the Comsol Multiphysics and CoventorWare softwares; showing a 90% power transmission efficiency at a 3.5 cm distance between coils. The implantable module includes aluminum- and polyimide-based devices, which allows ergonomic, robust, reproducible, and technologically feasible integrated sensors. In addition, the module shows a simplified and low cost design approach based on PolyMEMS INAOE® technology, featured by low-temperature processing.

Sustaining learners’ motivation to keep learning has been concerned for over 60 years in education and SLA. Most research focusing on Japanese university students has contributed lots of theoretical and practical developments, but research focusing on motivations of non-traditional adult learners and those under 18-year-old to learn Chinese is still little even though previous research findings have proved age is one of the key variables influencing learning besides nationalities and Chinese language levels. In order to find an effective treatment for sustainable Chinese language learning in Japan, this study utilized a survey method to analyze the types of Japanese learners’ motivation to learn Chinese via analysis of a moment structures (AMOS), and to compare the differences of the motivation via one-way ANOVA. This study revealed that Japanese learners’ motivation to learn Chinese consists of eight common types, which are “instrumental motivation”, “personal orientation”, “identified regulation”, “Chinese cultural productions”, “integrating into Chinese community”, “external regulation”, “social responsibility”, and “Chinese for academic purposes”. Also, there are similarities and differences existing in the eight motivation types among the Japanese children, adolescents, (non-) traditional adult learners of Chinese as a foreign language (CFL). The findings contribute the understanding of motivation types and differences among the four aged Japanese learners to teachers of teaching Chinese to speakers of other languages (TCSOL), and to future research further exploring how differently aged Japanese learners can have and use a higher motivation as a main drive to learn Chinese language as a lifelong business.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

A community-level nutrition intervention was implemented among tribal children (3 to 6 years) in Telangana, India. The one-year intervention involved six nutrient-rich formulations of millet-pulse-groundnut based products, suited to local taste preferences. Anthropometric measurements of height, weight and Mid-Upper-Arm -Circumference (MUAC) along with haemoglobin (Hb) levels were monitored at baseline and endline. The treatment group showed considerable gain in height (3.2 cm), weight (1.68 kg) and MUAC (0.33 cm), over the control group. Paired t-test indicated significant differences (p<.01) between pre- and post-intervention anthropometric measurements. Positive shifts were observed in wasting (WHZ; -1.2 ±1.3 to -0.9± 1), stunting (HAZ; -1.8±1.6 to -0.3±1.3) and underweight (WAZ; -1.9±1.2 to -0.7±1) among treatment group. Hb levels in the treatment group also improved significantly from 9.70 ± 0.14 g/dl (moderately-anaemic) to 11.08 ± 0.13 g/dl (non-anaemic). Post-intervention Focus Group Discussions (FGDs) involving mothers and teachers confirmed the positive impact. Thus, nutritional intervention formulated using climate resilient millets, pulses and groundnut, promotes dietary diversity and improves the nutrition & health status of children.

Luminescence-based sensors for measuring oxygen concentration are widely used both in industry and research due to the practical advantages and sensitivity of this type of sensing. The measuring principle is the luminescence quenching by oxygen molecules, which results in a change of the luminescence decay time and intensity. In the standard approach, this change is related to an oxygen concentration using the Stern–Volmer equation. This equation, which in most of the cases is non-linear, is parametrized through device-specific constants. Therefore, to determine these parameters every sensor needs to be precisely calibrated at one or more known concentrations. This work explores an entirely new artificial intelligence approach and demonstrates the feasibility of oxygen sensing through machine learning. The specifically developed neural network learns very efficiently to relate the input quantities to the oxygen concentration. The results show a mean deviation of the predicted from the measured concentration of 0.5 % air, comparable to many commercial and low-cost sensors. Since the network was trained using synthetically generated data, the accuracy of the model predictions is limited by the ability of the generated data to describe the measured data, opening up future possibilities for significant improvement by using a large number of experimental measurements for training. The approach described in this work demonstrates the applicability of artificial intelligence to sensing technology and paves the road for the next generation of sensors.

Since the beginning of the COVID-19 pandemic, extensive drug repurposing efforts sought to identify small molecule antivirals with various mechanisms of action. Here we aim to review research progress on small molecule viral entry and fusion inhibitors that directly bind to the SARS CoV-2 Spike protein. Early in the pandemic, numerous small molecules were identified in drug repurposing screens and reported to be effective in vitro SARS CoV-2 viral entry or fusion inhibitors. However, given minimal experimental information regarding the exact location of small molecule binding sites on Spike, it was unclear what the specific mechanism of action was, or where the exact binding sites were on Spike for some inhibitor candidates. The work of countless researchers has yielded great progress, with the identification of many viral entry inhibitors that target elements on the S1 receptor binding domain (RBD) or N-terminal domain (NTD) and disrupt S1 receptor binding function. In this review, we will also focus on highlighting fusion inhibitors that target inhibition of the S2 fusion function, either by disrupting the formation of the postfusion S2 conformation or alternatively by stabilizing structural elements of the prefusion S2 conformation to prevent conformational changes associated with S2 function. We highlight experimentally validated binding sites on the S1/S2 interface and on the S2 subunit. While most mutations to the Spike protein to date in variants of concern (VOCs) have been localized to the S1 subunit, the S2 subunit sequence is more conserved with only a few observed mutations in proximity to S2 binding sites. Several recent small molecules targeting S2 have been shown to have robust activity over numerous recent VOC mutant strains and/or greater broad spectrum antiviral activity for other more distantly related coronaviruses.

Intravitreal injections (IVTs) of corticosteroids as triamcinolone acetonide (TA) are frequently used for the treatment of many vitreous and retinal disorders. However, IVTs are related to severe ocular complications. Lately, a topical ophthalmic TA loaded liposomes formulation (TALF) was designed to transport TA into the posterior segment of the eye when instilled in the ocular surface. To evaluate the safety, tolerability, and biologic activity of TALF, an animal study and a phase I clinical assay was performed. Moreover, four patients with diabetic macular edema (DME) were treated with TALF in order to explore the biologic activity of the formulation. No inflammation, lens opacity, swelling or intraocular pressure rising were recorded after the instillation of TALF in any of the animal or clinical study. Mainly, mild and transient adverse events such as dry eye (30%) and burning (30%) were reported. TALF improves significantly visual acuity and diminishes central foveal thickness in patients with DME. The current data demonstrate the safety, tolerability, and biologic activity of TALF. It seems that TALF can be used topically to treat vitreous and retinal diseases that respond to TA such as DME, avoiding the use of corticosteroids IVTs and its associated hazards.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

Access to medicines is one of the essential problems in Public Health of low- and middle-income countries (LMICs). The World Health Organization (WHO) defines access to medicines as the possibility of "having continuously accessible and affordable medicines in public or private health facilities that are within a kilometer of the place of residence." Access to medicines, as defined by the WHO, is not fully guaranteed in many LMICs and even in many regions of high-resource countries. The WHO identifies several factors as determinants of limitations in the access to medicines: rational selection, affordable prices, sustainable financing, and reliable health services. The action on these factors makes it possible to improve universal access to medicines with consequent improvement in Public Health. Adequate access to antibiotics and vaccination will avoid a large part of the deaths caused by infectious diseases in the LMICs. However, the emergence of resistance and the difficulties in vaccination campaigns due to socio-political or cultural problems make it challenging to fight many easily treatable infectious diseases. The use and abuse of antibiotics are inevitably associated with the appearance of resistances that make them ineffective. Thus, whereas limited access to antibiotics raises mortality rates from infectious diseases, generalized open access to them ends up eliminating their clinical value. Moreover, the contraction of research in this field for many years has reduced the success in discovering new drugs. Additionally, local market regulations, inadequate selection, inaccessible prices, especially for those of second and third-generation, inefficient health systems, and difficulties of administration and control of prescription compliance, especially in the case of combined therapies, are additional obstacles to universal access to antibiotics. In order to simultaneously improve access to antibiotics and keep resistances under control, it is necessary to develop training and education activities at different social levels (from patients to various Health Care Providers) to complement the national or supranational strategic plans.