Recycled asphalt mixture is a material remixed with old asphalt recycled material (RAP) and new aggregate, and its application is of great significance in environmental protection.Due to the wear and tear of the old asphalt mixture, the road performance of the recycled asphalt mixture will decrease. This paper uses IPP software to obtain the shape characteristics of the old and new aggregates, and found that the roundness of the old aggregate of 9.5mm-16mm is the most serious wear. Therefore, the 30% RAP, and the influence of the roundness of the recycled asphalt mixture on the road performance is studied.

To verify the reliability of the proposed stitching linear scan method for roundness measurement of small cylindrical workpieces, measurement uncertainties of the workpieces with various dimension are conducted. The cross-sectional circle of a cylindrical workpiece is divided into several equal arcs to be measured. Thus, the arc profile can be characterized according to the measured arcs. The roundness profile of the cylindrical part can be obtained by stitching these arc profiles together. Firstly, the measurement uncertainty of the workpiece with a diameter 1.5 mm and length 5.8 mm is evaluated to be 0.095 μm which can meet the uncertainty target of 0.1 μm. Considering the uncertainty of θx and θz which are the alignment around X-axis and Z-axis respectively changing with workpiece dimension changing, relevant uncertainties are carried out. As a result, there is no limitation with respect to workpiece diameter theoretically If the alignment can reach θz = θx = ±0.1° without considering the measurable range of the machine.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

This purpose was to compare the ability of body shape index (ABSI) and body roundness index (BRI) with waist circumference (WC), body mass index (BMI), waist-to-hip ratio (WHR), waist-to-height ratio (WHtR) and body adiposity index (BAI) to predict metabolic risk. The cross-sectional study was conducted in 17,360 Chinese subjects (were aged 18-95 years old) who escaped cardiovascular disease (CVD) or diabetes. Biochemical and anthropometric variables were measured by trained staff. Receiver operating characteristic curve (ROC) and optimal cutoff values of obesity indices were recruited to compare the predictive ability for metabolic risk factors. The mean age of subjects was 53.7(13.1) years, 41.6 % were males. Within young group (<60 years), the areas under the curve (AUC) demonstrated that WC, BMI, WHR, WHtR and BRI were able to similarly predict high metabolic risk in males (0.74 vs. 0.74 vs. 0.73 vs. 0.73 vs. 0.73) and in females (0.73 vs. 0.73 vs. 0.71 vs. 0.73 vs. 0.73), while the approximate predictive ability were only acquired in males (0.73 vs. 0.73 vs. 0.70 vs. 0.73 vs. 0.73) within elder group (≥60 years). The optimal cut-off values of BRI for high metabolic risk were calculated in males (<60 y: 3.49 vs. ≥60 y: 3.46) and females (<60 y: 3.47 vs. ≥60 y: 3.60). Meanwhile, BRI displayed a strong prediction to elevated BP and elevated TG in males (AUC = 0.64; AUC = 0.70) and to elevated BP, elevated TG and elevated SUA in females (AUC = 0.67; AUC = 0.69; AUC =0.70). BRI was able to similarly predict high metabolic risk compared to WC, BMI, WHR, WHtR and BAI, while ABSI was not. Moreover, BRI revealed specific predictive ability for elevated BP, elevated TG and elevated SUA.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for Ti-6Al-4V by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were carried out to make a comparison between the experimental results. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for AA7050-T7451 by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of cutting variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is proved that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were performed to make a comparison between the experimental results. Experimental results have shown that machining performance in precision turn-boring process can be improved effectively through this approach