In this research work, an adaptive scheme for the coordinated protection of AC Microgrids using directional overcurrent (DOCR) relays is presented. Protection of AC MGs is a complex and challenging issue due to the dynamic nature of the network including, a) its capability to reconfigure the modes of operation ranging from grid-connected to the islanded mode, c) bidirectional-power flow capability, and c) integration of intermittent renewable energy resources with real-time variations in the resource availability. Consequently, the fault current contributions may largely vary depending upon the incident conditions on the network. Conventional protection schemes, generally designed for radial networks, and unidirectional power flow from the source end to the load may either mal-operate or exhibit very poor performance, if not adapted according to the dynamic conditions of the network. To address this issue, a communication-based adaptive protection scheme capable to adapt its settings according to the generation resource availability and network configuration is presented in this work. The proposed scheme consists of an intelligent central protection unit (ICPU) capable to update the settings and communicate it to the individual relays based on the pre-calculated offline settings. The directional overcurrent relays employed in the scheme use two-stage settings, i.e. definite time and inverse definite minimum time characteristics for the effective coordination among the downstream and upstream relays. An adaptive algorithm for ICPU operation is presented and a case study is implemented for a modified IEEE 9-bus system using DigSilent Power factory. The results for various scenarios including, a) grid-connected mode of operation, b) islanded mode of operation, and c) variable distributed generation mode are obtained and compared to the static scheme, which validates the effectiveness of the proposed scheme.

Relay protection service is the most crucial service carried by the electric power communication network, which is directly linked to the safe operation of the power grid. In the route planning of power services, a route planning architecture for the power communication network is constructed in this paper, considering the operation and maintenance requirements, such as relay protection service overload (RPSO) and dual route. To minimize network risk variance, the problem of single-service route allocation is formulated by taking the factors into account such as service delay, link bandwidth utilization, and RPSO constraints. Based on $k$ shortest paths algorithm, a route planning scheme for the power services is proposed, which considers RPSO and risk balance, and a strategy for implementing multi-service route planning of the communication network is studied. The simulation results show that the proposed route planning strategy can effectively avoid relay protection service overload, reduce network risk variance, and balance network risk.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

The reliability of Underwater Wireless Sensor Networks (UWSNs) is measured in terms of energy consumption (EC), end-to-end delay(E2E) and packet delivery ratio (PDR). The adverse effects of channel may cause data loss. Reducing delay up to possible extend improves the reliability of the network, also increasing the number of nodes in a particular network increase reliability. Besides, increasing the number of nodes improve reliability but also increase power consumption. In order to overcome these shortcomings, the two routing protocols are proposed in this paper, namely Delay and Reliability Aware Routing (DRAR) protocol and Cooperative Delay and Reliability Aware Routing (Co-DRAR) protocol for UWSNs. In DRAR protocol, network is divided into two equal regions where two sink nodes(SNs) are positioned at upper region of the network and two SNs are placed at the mid region of the network. The protocol choose the relay node based on residual energy (RE), distance and Bit Error Rate (BER). These parameters protect the data packets from corruption and also provide stable path (where nodes remain active for longer period and do not die quickly). The protocol uses single link and may get worse sometimes while changing channel circumstances. To address this problem, cooperative routing scheme is added to DRAR protocol in order to developed its enhanced version known as Co-DRAR protocol. The protocol works by allowing the destination to receive multiple copies of data packets in order to decide the quality of packets. The proposed protocols DRAR and Co-DRAR perform routing irrespective to geographical position of sensors nodes conversely to the some of conventional routing protocols that's way our propose protocol better perform than the well-known protocol i.e. Depth base routing (DBR) in terms of EC, E2E, PDR, dead nodes, packet drop ratio and number of alive nodes (ANs).

Home Security Systems are very important features of modern residential and office setups. This system is used to keep home safe from harmful gases, fire and intruders. It must be affordable, reliable and effective. In this paper, a GSM based home security system has been designed and implemented. The system consists of a GSM Module, MQ-2 smoke detector, Ultrasonic sonar sensor, LM35 temperature sensor, Arduino Uno and relay module. The MQ-2 smoke detector is used to detect harmful gases i.e. LPG, CH4, CO, Alcohol, Smoke or Propane. Any of the harmful gases stated above is detected it will warn the owner by activating the buzzer and displaying a warning message on the LCD display. It will also send a SMS to the owner. Our system can also measure temperate and if the temperature is increased above a certain range it will compensate it by activating Air Conditioner through the relay module. The system will also send a SMS to the owner. It can also detect intruders using Ultrasonic sensor and warn us through buzzer, SMS and displaying message on the LCD. Our system is reliable as it has very fast response and cost effective and it has been developed using our own technologies.

Home Security Systems are very important features of modern residential and office setups. This system is used to keep home safe from harmful gases, fire and intruders. It must be affordable, reliable and effective. In this paper, a GSM based home security system has been designed and implemented. The system consists of a GSM Module, MQ-2 smoke detector, Ultrasonic sonar sensor, LM35 temperature sensor, Arduino Uno and relay module. The MQ-2 smoke detector is used to detect harmful gases i.e. LPG, CH₄, CO, Alcohol, Smoke or Propane. Any of the harmful gases stated above is detected it will warn the owner by activating the buzzer and displaying a warning message on the LCD display. It will also send a SMS to the owner. Our system can also measure temperate and if the temperature is increased above a certain range it will compensate it by activating Air Conditioner through the relay module. The system will also send a SMS to the owner. It can also detect intruders using Ultrasonic sensor and warn us through buzzer, SMS and displaying message on the LCD. Our system is reliable as it has very fast response and cost effective and it has been developed using our own technologies.

In this paper, we first investigate secure communications for a two-hop interference relay system in the wireless Internet of Things (IoT), where K source-destination pairs communicate in the presence of an eavesdropper. Explicitly, we jointly design source, relay and destination matrices upon minimizing total mean-squared error (MSE) of all legitimate destinations while keeping the MSE at eavesdropper above a certain threshold. We illuminate that the joint design of the source, relay and destination matrices subject to both secrecy and transmit power constraints. More specifically, we proposed an efficient iterative distributed algorithm to simplify the process of the joint design for optimal source, relay and destination matrices. Furthermore, the convergence of the iterative distributed algorithm is described. Additionally, the performances of the proposed algorithm, including both its secrecy rate and MSE, are characterized with the aid of simulation results. We demonstrate that our proposed algorithm outperforms the traditional approach. As a benefit, secure communications can be guaranteed by using the proposed algorithm for the multiple input multiple output (MIMO) interference relay IoT network in the presence of an eavesdropper.

Unmanned Aerial Vehicles (UAVs) in particular multirotors are becoming the {\it de facto} tool for aerial sensing and remote inspection. In large industrial facilities, a UAV can transmit an online video stream to inspect difficult to access structures, such chimneys, deposits and towers. However, the communication range is limited, constraining the UAV operation range. This limitation can be overcome with relaying UAVs placed between the source UAV and the control station, creating a line of communication links. In this work we assume the use of a digital data packet network technology, namely WiFi, and tackle the problem of defining the exact placement for the relaying UAVs that creates an end-to-end channel with maximal delivery of data packets. We consider asymmetric communication links and we show an increase as large as $15$\% in end-to-end packet delivery ratio when compared to an equidistant placement. We also discuss the deployment of such a network and propose a fully distributed method that converges to the global optimal relay positions taking, on average, 1.4 the time taken by a centralized method.

With the introduction of the IEC 61850 standard, the path is set for a single communication topology covering all substation levels. The standard has the potential to change the way substations are designed, build, tested and maintained. This means that the key segment of the substation, its protection system, will go through a transition period with the end goal of having a digitalized substation where all information exchange is performed over an Ethernet communication bus. The goal of this paper is to analyse the performance impact of the IEC 61850-9-2LE on the protection system. To do this, a laboratory hardware-in-the-loop test setup is developed representing traditional, hybrid and digital substation topology. This setup served to simulate faults and create transient waveforms in an extended IEEE 123 node test system, which were then used to detect the reaction times of protection relay devices. To verify protection relay results significant number of tests are performed clearly showing benefits which can be gained by distribution system digitalization.

This paper considers a hybrid relay network consisting of the source, the amplify-and-forward (AF) relay, the decode-and-forward (DF) relay, and the destination. We propose the optimal power allocation schemes between two different relays which maximize the achievable rate under a sum relay power constraint for given channel gains and transmit power from source. By solving the optimization problem to maximize the achievable rate for each relay network, the transmit power values in closed-form are derived. When the channel gains are the same, the optimal power allocation scheme for AF-DF relay network proves that a more power should be allocated at the first relay to maximize the achievable rate. In case of the DF-AF relay network, we derive the optimal power allocation scheme for the possible four cases. Under the same SNR condition at the first hop, we show that the achievable rate of AF-DF relay network is greater than that of DF-AF relay network when the channel gain between two relays is higher than that between the second relay and destination. Simulation results show that the proposed power allocation schemes provide a higher achievable rate than the equal power allocation schemes.

In the context of energy decarbonization, wind farms with type IV wind turbines from various manufacturers are being massively put into operation. These wind turbines comply with the requirements of the grid codes of the countries where they are designed and/or manufactured, but do not factor in the specific features of the distribution networks of other countries to which they are connected. The study at issue involves a comparative analysis of the requirements of grid codes of different countries for the stable operation of wind turbines under standard disturbances. The Low Voltage Ride Through (LVRT) characteristic implemented in type IV wind turbine inverters makes it possible to prevent wind turbine shutdowns in case of short-term voltage dips of a given depth and duration. The calculations of transient processes indicate that wind turbines may not meet the requirements of the grid code of a particular country for their stable operation. As a result, standard disturbances will block the reactive current injection and the wind turbine will be switched off. This is often caused by the relay protection devices with a time delay of 1-2 s, which are used in distribution networks and implement the functions of long-range redundancy. Excessive shutdowns of wind turbines lead to emergency rise in the load for the generating units of conventional power plants, aggravating the post-accident conditions and disconnecting consumers of electricity. The paper presents a method for checking the LVRT characteristic settings for compliance with the technical requirements for wind turbines. To prevent wind turbine outages, one should either change the configuration of the LVRT characteristic, or upgrade the relay protection devices in the distribution network adjacent to the wind farm, or implement group or individual technical solutions at the wind farm. The performance of the proposed technical solutions is confirmed by the calculations of transient processes.

This paper considers a two-way relay network, where two source nodes exchange messages through several relays in the presence of an eavesdropper, and the channel state information (CSI) of the eavesdropper is imperfectly known. The amplify-and-forward relay protocol is used and the relay beamforming weights are designed. The model is built up to minimize the total relay transmit power while guaranteeing the quality of service at users and preventing the eavesdropper from decoding the signals. Due to the imperfect CSI, a semi-infinite programming problem is obtained. An algorithm is proposed to solve the problem, and the iterative points are updated through the linesearch technique, where the feasibility are preserved during iterations. The optimality property is analyzed. The obtained subproblems are quadratic constrained quadratic programming problems, either with less than $4$ constraints or with only one variable, which are solved optimally. Simulation results demonstrate the importance of the proposed model, and imply that the proposed algorithm is efficient and converges very fast, where more than 85% of the problems are solved optimally.

Underwater Wireless Sensor Networks (UWSN) enables various oceanic applications which require effective packet transmission. In this case, sparse node distribution, dynamic network topology and inappropriate selection of relay nodes cause void holes. Addressing this problem, we present a Relay based Void Hole Prevention and Repair protocol (ReVOHPR) by multiple Autonomous Underwater Vehicles (AUV) for UWSN. ReVOHPR efficiently identifies and avoids void holes and trap relay nodes to avoid it. ReVOHPR adopts the following operations as Ocean Depth (levels) based Equal Cluster Formation, Dynamic Sleep Scheduling, Virtual Graph based Routing, and Relay Assisted Void Hole Repair. For energy efficient cluster forming, Entropy based Eligibility Ranking (E2R) is presented which elects stable cluster heads (CHs). Then, dynamic sleep scheduling is implemented Dynamic Kernel Kalman Filter (DK2F) algorithm in which Sleep and Active modes based on the nodes current status. Inter Cluster Routing is performed by maximum matching nodes which selects by Dual criteria and also data transmitted to AUV. Finally, void holes are detected and repair by Bi-Criteria Mayfly Optimization (BiCMO) algorithm. The BiCMO focuses on reducing the number of holes, data packet loss and maximizes Quality of Service (QoS) and energy efficiency of the networks. This protocol is timely deal with node failures in packet transmission via multi-hop routing. Simulation is implemented by NS3 (AquaSim module) simulator that evaluates the performance in network simulation for following metrics as average energy consumption, delay, packet delivery rate and throughput.

Enabling D2D communication in the mm-Wave band has many obstacles which must be mitigated. The primary concern is the introduction of interference from various sources. Thus, we focused our work on the performance of decode and forward (DF) relay assisted D2D communication in the mm-Wave band for increasing the coverage probability and energy efficiency (EE). Three modes are proposed for D2D communication to prevail. Bit-wise binary XOR operation is executed at the relay node which increases the security feature. Radius of coverage expression is derived which indicates the switching of the modes. The diffused incoherent scattering power is also considered as a part of power consumption. Furthermore, a unique relay selection scheme, Dynamic relay selection (DRS) method is proposed to select the optimal relay for information exchange. Comparison of the proposed DF relay scheme with amplify and forward (DF) scheme is also shown. Finally, simulation results prove the efficacy of the proposed work.

Cooperative non-orthogonal multi access communication is a promising paradigm for the future wireless networks because of its advantages in terms of energy efficiency, wider coverage and interference mitigating. In this paper, we study the secrecy performance of a downlink cooperative non-orthogonal multi access (NOMA) communication system under the presence of an eavesdropper node. Smart node selection based on feed forward neural networks (FFNN) is proposed in order to improve the physical layer security (PLS) of a cooperative NOMA network. The selected cooperative relay node is employed to enhance the channel capacity of the legal users, where the selected cooperative jammer is employed to degrade the capacity of the wiretapped channel. Simulations of the secrecy performance metric namely the secrecy capacity ($C_S$) are presented and compared with the conventional technique based on fuzzy logic node selection technique. Based on our simulations and discussions the proposed technique outperforms the existing technique in term the of secrecy performance.

As our understanding of the thalamocortical system deepens, the questions we face become more complex. Their investigation requires the adoption of novel experimental approaches complemented with increasingly sophisticated computational modeling. In this review, we take stock of current data and knowledge about the circuitry of the somatosensory thalamocortical loop in rodents, discussing common principles across modalities and species whenever appropriate. We review the different levels of organization, including the cells, synapses, neuroanatomy, and network connectivity. We provide a complete overview of this system that should be accessible for newcomers to this field while nevertheless being comprehensive enough to serve as a reference for seasoned neuroscientists and computational modelers studying the thalamocortical system. We further highlight key gaps in data and knowledge that constitute pressing targets for future experimental work. Filling these gaps would provide invaluable information for systematically unveiling how this system supports behavioral and cognitive processes.

This paper presents a study on optimization of Overcurrent relay (OCR) coordination protection scheme for Sustainable Standalone Hydrokinetic Renewable Energy (SHRE) distribution network at Batang Rajang river, located at Kapit Sarawak, Malaysia by turning river stream into power generation source. The purpose of the project is to develop rural electrification system for native long houses along the river. The research study is tested on a DigSILENT develop model of the SHRE distribution network and in accordance with all respectively unique parameters and relevant standards. Since this is a new standalone distribution system, an efficient and properly coordinated overcurrent protection system must be provided. Improper and miscoordination among OCRs result in maloperation of the protection system that can lead to false tripping and an unnecessary outage and power system instability. Thus, the objective of this work is to employ Genetic Algorithm (GA) technique in Matlab/Simulink for optimal overcurrent coordination and settings among all OCRs in the proposed distribution network in order to improve the speed of OCR tripping operation. The GA is used because the project is fast track and requiring the simplest method available. In this strategy, time dial setting (TDS) is optimized by using plug setting multiplier (PSM) as the constraint. The obtained results show a significant improvement of the relay operating time of 36.01% faster than that of conventional numerical technique during fault occurrence. Thus, an efficient and reliable overcurrent protection scheme has been achieved for the SHRE distribution network.