Diffusion bonding is often used on pre-machined parts to generate internal cavities, e.g. for cooling injection molding tools close to the mold cavity. Only then, the workpieces are finished to their final dimensions. In the case of micro-process devices, however, it is essential to precisely control the deformation, as otherwise uncontrollable pressure losses will occur with channel cross-sections in the sub-millimeter range. Post-processing is not possible. The most important process parameters for diffusion bonding are temperature, dwell time and contact pressure, with the bonding temperature and contact pressure acting in opposite directions and showing a strong non-linear dependence on deformation. In addition, the deformation is influenced by a number of other factors such as the absolute size of the cross-section and the aspect ratio of the parts, the dimensions and distribution of the internal cross sections and the overall percentage of the cross-section to be bonded. In micro process engineering, small material cross-sections in the range of the materials microstructure can facilitate additional deformation mechanisms such as grain boundary sliding, which are not relevant at all for larger structures. For parts consisting of multiple layers, tolerances in thickness and roughness of multiple surfaces must be levelled, contributing to the percentaged deformation. This makes it difficult, especially in micro process engineering and in single or small series production, to determine suitable joining parameters in advance, which on the one hand do not cause unforeseen large deformations, but on the other hand reliably produce highly vacuum-tight components. Hence, a definition of a fixed percentaged deformation does not work for all kinds of components. This makes it difficult to specify parameters for surely obtain high-vacuum tight parts. For successful diffusion bonding, atoms must diffuse over the bonding planes, forming a monolithic part in which the original layers are no longer visible. Only then, mechanical properties identical to those of the base material, which has been subjected to identical heat treatment, can be achieved. In this paper, the impacts of different material cross section widths as well as of the aspect ratio on deformation were investigated. By accident, it was found that also accuracy of the temperature measurement may have a serious impact in terms of deformation.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

In order to solve the problem of environmental pollution caused by a large number of discarded hickory husks in Lin'an, and to make them a clean energy source that can be recycled, in this paper,using crushed hickory husks as raw material, single factor test was carried out on a hydraulic plunger forming machine with different moisture content and length-diameter ratio of forming sleeve.The change of axial pressure and radial force in the forming sleeve is measured by the sensor, and the microstructure of the biomass moulding fuel briquette was observed by stereomicroscope. The results showed that the hickory husks could be compressed and formed at room temperature. When the moisture content of the hickory husks is 14% and the length-diameter ratio of the forming sleeve is 4.5, the forming quality is the best, and the relaxation density of the formed briquette is up to 0.98g /cm3. When the moisture` content is the same, the forming pressure increases with the increase of the length-diameter ratio of the forming sleeve. When the length-diameter ratio of molding sleeve is the same, the molding pressure increases first and then decreases with the increase of water content.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

In this study, the thermal behavior of a PCM-based heat sink in the presence of horizontal fins was numerically investigated. These types of heat sink can be effective in electronic cooling applications. Independent variables included aspect ratio (AR), number of horizontal fins (n) and their length (LR), while the objective function was defined to maximize the safe operation time (tmax). The incorporation of horizontal fins has a positive effect (thermal conductivity enhancement) as well as a negative effect (latent heat reduction). Based on the results, the optimal number of horizontal fins was five. As the number of fins rises up to five, the incremental effect of thermal conductivity improvement (positive effect) was superior to the decremental effect of the latent heat reduction (negative effect), hence the objective function (tmax) improved. However, with a further increase in the number of fins upon five, the negative effect prevailed over the positive effect and therefore the safe operation time diminished.

In this paper, the Fourier-based synchrosqueezing transform (FSST) method is introduced into the power system to realize low frequency oscillation identification. Firstly, the modal components of low frequency oscillation signal are separated by FSST, and calculating the instantaneous parameters including magnitude, frequency and phase of every mode component with Hilbert transform. Then , calculating the damping ration of every modal component based on above parameters and derived the formulas. Thus, it realized effective identification of of modal parameters of low frequency oscillation signal. The experimental results of simulated data and 16-generator system demonstrate the validity and correctness of the FSST method. Comparing with the classical Prony method shows that the FSST method is better in the identification accuracy when the low frequency oscillation signal is polluted by noise. Finally, the effectiveness of the FSST in Actual power grid is verified based on the real data from Sichuan power grid.

The role of land surface temperature (LST) is of utmost importance in multiple academic disciplines such as climatology, hydrology, ecology, and meteorology. Until to now, many methods have been proposed to estimate LST from satellite thermal infrared data. The Thermal Infrared Sensor (IRS) on the Chinese ZY1-02E satellite is a pivotal instrument employed for gathering thermal infrared (TIR) data of land surfaces. The objective of this research is to evaluate the feasibility of a single-channel approach based on water vapor scaling (WVS) for deriving LST from ZY1-02E IRS data because of its wide spectrum range, i.e., 7~12μm, affected strongly by both atmospheric water vapor and ozone. Three study areas, namely Baotou, Heihe River Basin, and Yantai-sea sites, were selected as validation sites to evaluate the LST inversion accuracy. This evaluation was also conducted by cross-comparison between the retrieved LST and MODIS LST product. The results revealed that the WVS-based method exhibited an average bias of 0.63K and an RMSE of 1.62K compared to the in-situ LSTs. The WVS-based method demonstrated reasonable accuracy through cross-validation with the MODIS LST product, with an average bias of 0.77K and RMSE of 2.0K. These findings provide that the WVS-based method is effective to estimate LST from ZY1-02E IRS data.

Plantation-based farmer cooperatives play an important role in promoting agricultural modernization and increasing farmer income, and the management of business risks of such cooperatives not only influences the development of the cooperatives themselves, but also concerns the interests of farmers. Based on the survey data of 226 sample cooperatives from Guizhou province, this article uses factor analysis to measure business risks of plantation-based farmer cooperatives and carries out empirical tests on influence factors of business risks through structural equation model. According to the research results, the ordering of business risks of plantation-based farmer cooperative based on their significance is as follows: market risk > policy risk > natural risk > technical risk > management risk. Influence factors including policy environment, economic environment, social service environment, technical environment, resource endowment of the cooperative and manager characteristics have significant positive influence on the cooperative, with economic environment and manager characteristics generating relatively stronger influence and social service environment generating relatively weaker influence. Through this research, several policy implications on driving high-quality development of plantation-based farmer cooperative are made, including specifying supportive policies of plantation-based farmer cooperative, improving economic environment of agricultural market, upgrading agricultural infrastructure, depending reform of land transfer system, and enhancing internal management of the cooperative.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

Tumor to stroma ratio is a highly debated prognostic factor in the management of several solid tumors and there is no universal agreement on its practicality. In our study we proposed to confirm or dismiss the hypothesis that a simple measurement of stroma quantity is an easy-to-use and strong prognostic tool. We have included 74 consecutive patients with colorectal cancer who underwent primary curative abdominal surgery. The tumors have been grouped into stroma-poor (stroma &lt;10%), medium-stroma (between 10 and 50%) and stroma-rich (over 50%). The proportion of tumor stroma ranged from 5% to 70% with a median of 25%. Very few, only 6.8% of patients had stroma-rich tumors, 4% stroma-poor tumors and 89.2%tumors with a medium quantity of stroma. The proportion of stroma, at any cut-off, had no statistically significant influence on the disease specific survival. This can be explained by the low proportion of stroma-rich tumors in our patient group and the inverse correlation of stroma proportion with tumor grade. The real-life proportion of stroma-rich tumors and the complex nature of the stroma-tumor interaction has to be further elucidated.

Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (30.5cm×22.5cm). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.

Infectivity assays are the key analytical technology for development of manufacturing processes for virus-based therapeutics. Here, we introduce a novel assay format that utilizes label-free bright field images to determine the kinetics of infection-dependent changes in cell morphology. In particular, cell rounding is directly proportional to the amount of infectious virus applied, enabling rapid determination of viral titers in relation to a standard curve. Our kinetic infectious virus titer (KIT) assay is stability-indicating and, due to its sensitive readout method, provides results within 24 hours post-infection. Compared to traditional infectivity assays, which depend on a single readout of an infection endpoint, cumulated analysis of kinetic data by a fit model results in precise results (CV &lt; 20%) based on only three wells per sample. This approach allows for a high throughput with ~400 samples processed by a single operator per week. We demonstrate the applicability of the KIT assay for VSV-GP and NDV, but it can potentially be extended to a wide range of viruses that induce morphological changes upon infection. The versatility of this assay, combined with its independence from specific instruments or software, makes it a promising solution to overcome the analytical bottleneck in infectivity assays within the pharmaceutical industry and as a routine method in academic research.

Traditional refractory materials such as nickel-based superalloys have been gradually unable to meet the performance requirements of advanced materials. The Mo-Si-based alloy, as a new type of high temperature structural material, has entered the vision of researchers due to its charming high temperature performance characteristics. However, its easy oxidation and even "pesting oxidation" at medium temperatures limit its further applications. In order to solve this problem, researchers have conducted large numbers of experiments and made breakthrough achievements. Based on these research results, the effects of rare earth elements like La, Hf, Ce and Y on the microstructure and oxidation behavior of Mo-Si-based alloys were systematically reviewed in the current work. Meanwhile, this paper also provided an analysis about the strengthening mechanism of rare earth elements on the oxidation behavior for Mo-Si-based alloys after discussing the oxidation process. Furthermore, the research focus about the oxidation protection of Mo-Si-based alloys in the future was prospected to expand the application field.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

In the context of intelligent and integrative lighting, in addition to the need for color quality and brightness, the non-visual effect is essential. This refers to the retinal ganglion cells (ipRGCs) and their function, first proposed in 1927. The melanopsin action spectrum has been published in CIE S 026/E: 2018 with the corresponding melanopic equivalent daylight (D65) illuminance (mEDI), melanopic daylight (D65) efficacy ratio (mDER) and 4 other parameters. Due to the importance of mEDI and mDER, this work synthesizes a simple computational model of mDER as the main research objective, based on a database of 4214 practical spectral power distributions (SPDs) of daylight, conventional, LED, and mixed light sources. In addition to the high correlation coefficient R2 of 0.96795 and the 97% confidence offset of 0.0067802, the feasibility of the mDER model in intelligent and integrated lighting applications has been extensively tested and validated. The uncertainty between the mEDI calculated directly from the spectra and that obtained by processing the RGB sensor and applying the mDER model has reached ± 3.3% after an appropriate matrixing process and proper illumination characterization combined with the successful mDER calculation model. This result opens the potential of low-cost RGB sensors for applications in intelligent and integrative lighting systems to optimize and compensate the non-visual effective parameter mEDI using daylight and artificial light in indoor spaces. The goal of the research on RGB sensors and the corresponding processing method are also presented and their feasibility is methodically demonstrated. A comprehensive investigation with a huge amount of color sensor sensitivities is necessary in a future work of other researches.

To address the large hysteresis and susceptibility to instability in high-speed deposition fusion moulding (FDM) 3D printing’s temperature control, this paper proposes an improved ant-lion optimization algorithm (OCALO) to optimize the PID parameters.The improvement aims to solve the problem that the traditional ant-lion optimization algorithm (ALO) reduces the population diversity and tends to fall into the local optimal solution when it is close to the global optimal solution.The generation of the initial solution is enhanced by the introduction of a new Tent-Logistic-Cotangent composite chaotic mapping. This integration into Elite Opposition-Based Learning aids in optimizing population diversity. Concurrently, the incorporation of cosine factors of a specified parameter into the elitist formula of the traditional ALO algorithm is aimed at reducing the tendency of ants to randomly gravitate towards ant-lions with lower fitness values. This adjustment helps in balancing the exploration-exploitation trade-off in the algorithmic process. Compared with two existing classical algorithms and three improved ALO algorithms, the algorithm improves the convergence speed, global search ability and the ability to jump out of the local optimal solution. The improved algorithm was combined with PID control to design an OCALO-PID temperature controller and simulated on a high-speed 3D printing temperature model identified by modelling. The results show that the method improves the transient and steady-state performance of reactor temperature control with good control accuracy and robustness. Finally, the proposed algorithm is applied to a physical experimental platform to verify the feasibility of the algorithm.

The oil and gas sector has recognised structural integrity assessment of ageing platform for prospective life extension as a rising concern, particularly in encountering the randomness of the harsh ocean environments. This condition leads to uncertainty in wave-in-deck load estimates and a high load level being imposed on offshore structures. This emphasises the necessity of enhanced reliability, as failure might result in inaccessibility because of the uncertainties related to long-distance services, such as accuracy of predictions of loads and responses. Even though the established guidelines present a fundamental assessment, additionally, comprehensive rules are required. This paper performed a reliability analysis incorporating practical approaches that can more accurately represent time-dependent structural deterioration. The following two procedures have been adopted by a majority of significant oil and gas operators to monitor the safety and integrity of these structures: a) Ultimate Strength Assessment (USA) method and b) Reliability Design Assessment (ReDA) method. A comparison of these two reliability approaches was performed on selected ageing jacket structures in the region of the Malaysian sea. The comparative findings, namely, reserve strength ratio (RSR) at various years of the return period (RP) and ratio value for risk of failure regarding the probability of failure (POF), provided a check and balance in strengthening confidence in the results. The findings showed that the structural components might safely survive either using the USA and ReDA method in such conditions, as the reliability indexes were determined to be satisfactory compared to allowable values from ISO 19902 design specifications. Therefore, these evaluations were determined to control the risk level of the structure during the remaining of its lifetime and undertake cost-effective inspections or mitigation strategies when necessary.

In public health literature the risk of death or disease associated with a dietary, environmental of behavioral factor is most commonly denoted by odds ratio (OR), hazard ratio (HR) or risk ratio (RR). The ratio indices have several desirable statistical properties. However, the most important question is whether there are some evolved innate norms of perception of risk that people use and what they are. We conducted a simple one question survey of 98 individuals with different age, sex, educational and professional backgrounds. The respondents were asked to judge the relative perceived risk of four different hypothetical habits for which data on the percentage of people affected by the disease with and without the habit was given. They were asked to rank the risks for the four habits. Results showed that the habits that had the highest difference between probability of acquiring the disease were ranked high on risk perception. The probability ratios did not affect risk perception significantly. Further age, sex, profession or formal training in statistics did not affect the response significantly. Even individuals that were formally trained to use OR and HR as risk indicators, preferred using probability differences over ratios for judging their own risk in the perceived context. This preliminary inquiry into intuitive statistical perception suggests that designing statistical indices based on people’s innate perception may be a better strategy than trying to train people to understand the indices designed by expert statisticians.

Background: Psoriasis is a chronic immune-mediated skin disease in which systemic inflammation plays an important role in the pathogenesis. In recent years, neutrophil-to-lymphocyte ratio (NLR), neutrophil-to-monocyte ratio (NMR), platelet-to-lymphocyte ratio (PLR), and systemic immune-inflammation index (SII) have been shown to be important indicators of inflammation. In this study, our aim is to investigate NLR, NMR, PLR, and SII levels in psoriasis patients treated with biologic agents. Method: Clinical and biochemical data of 209 patients who received systemic therapy for psoriasis were obtained by retrospectively reviewing their medical records. NLR, NMR, PLR, and SII values were calculated from the hemogram values of the patients. Results: In the third month of follow-up, the mean CRP, NLR, NMR, PLR, and SII values were significantly decreased compared to the baseline values. SII values showed strong positive correlations with NLR, NMR and PLR. Adalimumab, etanercept, and infliximab, which are TNF-α blockers, were observed to be more effective on PLR and NLR and especially NMR. Conclusion: NLR, NMR, PLR, and SII, which are data obtained from routine blood tests, can be used in the monitoring of treatment of psoriasis, especially with TNF- α blockers.

: Clay covers a substantial portion of the Earth. Such soil covers Iraq’s central and southern regions, where the depth of the clay may reach 150 m. All enhancement techniques and methods for transporting large loads cease to function or become prohibitively expensive in such soils. In this case, thermal treatment is the most effective method. In this study, a novel heating system was created and produced utilizing gas as the heat source via boreholes that simulate reality. The borehole heating cases were planted inside soft clay soil to enhance the soil. Different parameters were investigated, including the spacing between boreholes (3, 4, and 5 times the outer diameter of the borehole), the heating depth (1, 1.5, 2, and 2.5 times the width of the model footing), the duration of heating (2, 4, 6, 8, and 10 hrs), and the pattern (square, circular, triangular). The results showed the strength and behavior of the soil treated with heated boreholes at varying spacings, depths, patterns, and heating periods. The best results were found for a spacing, depth, and heating time of three times the outer diameter of the borehole, two times the width of the footing model, and eight hours, respectively. The effect of the heated borehole casing pattern was small when the heated borehole casing was used. The experiments conducted on heated soil showed that the undrained shear strength (Cu) increased from 14 to 360 kPa and then dropped to 140 kPa (as an average with depth). In contrast, the average angle of internal friction (Ø) rose from 0 to 52 degrees and decreased to 16 degrees (as an average with depth) from the center of the heating model to the furthest point affected by heating. In addition, the EDS pattern showed that components like silicon, aluminum, and iron dropped at 300 °C and rose at 400 °C in the treated soils. At 200 °C, the calcium content rose, and then dropped dramatically at 400 °C. The carbon percentage increased at 300 °C and decreased at 400 °C. The elements’ proportions showed little change or remained stable at temperatures between 400 °C and 600 °C.

Background: Infections are a major cause of morbidity and mortality in patients with pemphigus vulgaris (PV). One of the most common infections in these patients is candidiasis. This is probably due to the use of systemic immunosuppressant, including oral and intravenous corticosteroids, mainly in megadoses (pulse therapy), although it is unknown if there are other associated factors in addition to immunosuppressive treatment. We determine the factors associated with candidiasis in PV patients in two Second-Care hospitals in Mexico. Methods: We reviewed 100 cases with PV. Cases were randomly selected from the databases of two second-care hospitals between January 2010 and December 2019 (10 years). The primary endpoint was the incidence of candidiasis in patients with PV. Results: One hundred patients with PV were enrolled in this retrospective study. Candidiasis was observed in 79 patients (79%). A maximum corticosteroid dose of 55 mg/day during the last year (p = 0.001) and higher neutrophil/lymphocyte ratio were associated with candidiasis in patients with PV (p = 0.001). Conclusion: Risk factors favoring candidiasis in patients with PV are not only related to the use of corticosteroids, but also to demographic factors, the activity of the disease, and the systemic inflammation associated with autoimmunity.

Academic and corporate research has been focusing on analyzing stock performances, financial markets, and investment strategies for decades. According to Lynch and Rothchild (1989), certain investments can be described as plays. In this work, the authors use the term for investments in value stocks, spin-offs, and turnarounds to analyze the long-term stock performance and risk-adjusted excess returns of up to five years for those stocks. Additionally, stocks with a supe-rior return performance are identified within an investment play based on low P/E and P/B mul-tiples. The study finds that value stocks, spin-offs, and turnarounds outperform the S&P 500 on average on a one-, three- and five-year investment horizon. The analysis of the three investment plays confirms earlier studies that investment plays constitute a profitable investment opportunity. Moreover, the research exemplifies that private investors could achieve an excess return (alpha) through a passive buy-and-hold investment strategy. Overall, the analysis provides a deeper in-sight into the long-term performance of value stocks, spin-offs, and turnarounds.

In estimating the maximum and minimum index void ratios for mixtures of sand and silt, the values of several empirical constants must be determined based on the type of sand and silt involved. These empirical constants are the filling coefficient, a, and embedment coefficient, b, both of which can be determined either through lab testing or correlations. These constants are then used in equations to predict the maximum and minimum index void ratios of the sand-silt mixtures. The study reported here developed simple correlations for estimating the filling and embedment coefficients using readily obtained laboratory data. These models were found to be excellent in developing filling and embedment coefficients that accurately (R2 values typically of 0.94 or greater.) predicted values of the index void ratios for sand and silt mixtures.

Background: Since the previous study dealing with the case fatality ratio and infection fatality ratio caused by COVID-19, the author has received many comments that prompted the question: "Why did an optimistic prognosis fail?" To answer this question, a more detailed and expanded analysis was carried out in a new study. Objective: To evaluate the dynamics of monthly numbers of cases, deaths, tests and CFR worldwide during three phases of the COVID-19 pandemic. Material and Methods: Twenty three sets of databases, dated the 22nd of each month from January 2020 to November 2021, for 213 countries were collected from the Worldometer website. The number of cases, deaths, tests, CFR, IFR, etc. were counted for various periods of time for each of the 213 countries, then results related to different periods of time were compared. Results: The analysis of the main epidemiological parameters led to the division of three phases of the global pandemic evolution. The first phase (23.01.20-22.07.20), the second phase (23.07.20-22.01.21) and the third phase (23.01.21-22.07.21) were different in terms of the number of tests performed, new cases, and mortality due to COVID-19. By the end of the second phase, the worldwide statistics indicated the imminent end of the pandemic, but the third phase was characterized by a sudden rise in the number of new cases and deaths that could not be explained rationally. The most dramatic evolution of the epidemic curve occurred in the countries where doctors had successfully battled COVID-19 during the first two phases of the pandemic. Conclusions: Despite the decrease in overall death numbers during the latest months analyzed, additional study is necessary to identify the cause for the increase in the number of new cases and deaths during the third phase of the pandemic. Only complete information regarding the positive and negative impact of medical and non-medical methods of diagnostics and prophylaxis of COVID-19 can help to organize effective measures to end the current pandemic and prevent a similar one from occurring in the future. Presumably, there are several causes of the negative evolution of the current pandemic, including the overreliance on PCR tests, application of non-specialized premises for quarantine and treatment, decrease in herd and individual immunity, inadequate change of therapeutic protocols, and ignoring prophylactic treatment. It can be suggested that the use of immunemodulatory drugs, for example, thymus extract or thymic peptides, in groups of people with compromised immunity is necessary, and prophylactic and therapeutic protocols should be changed from the 'standard' types to 'personalized' ones.

Manufactured sand and natural sand have great differences in terms of physical properties, chemical composition, and so on. In the mix ratio design of manufactured sand concrete, the traditional common concrete ratio cannot be used. The water-cement ratio playing a crucial role in the mix ratio design. The optimum water-cement ratio can not only improve concrete performance, it can also reduce cement consumption and costs. The present study examines the working performance indicators and mechanical performance indicators of manufactured sand concrete using Fujian granite with three strength grades (C35, C40 and C50) at different water-cement ratios. The impact of water-cement ratio on the operational and mechanical performance of manufactured sand concrete with different strength grades is analyzed and summarized. Revised sentence: The findings suggest that the workability of Fujian granite concrete is directly influenced by the water-cement ratio. Additionally, the water-cement ratio indirectly affects the mechanical properties of manufactured sand concrete. Finally, when changing the water-cement ratio, cube compressive strength, splitting tensile strength and bending strength exhibit similar trends. The optimal water-cement ratio for C35 concrete is determined to be 0.39, considering the workability and mechanical properties of Fujian granite manufactured sand concrete. Similarly, the optimal water-cement ratio for C40 concrete is 0.34, while for C50 concrete it is 0.32.

Objective: To explore three novel fasting blood glucose (FBG)-based novel indicators, including FBG-to-albumin ratio (FAR), FBG-to-lymphocytes ratio (FLR), and FBG-to-hemoglobin ratio (FHR), in predicting prognosis and detecting metastasis for patients with pancreatic neuroendocrine neoplasms after resection. Materials and methods: A total of 178 pNEN patients underwent surgical resection were included in this study. Receiver operating characteristic (ROC) curves were used to evaluate the diagnosis values of FAR, FLR, and FHR, and the cut-off values were obtained for further analyses. Univariate and multivariate analyses were conducted to determine the independent predictors. The Kaplan-Meier method was used to evaluate the progression-free survival (PFS) and overall survival (OS) of the pNEN patients. Results: The optimal cut-off values of FAR, FLR, and FHR were 0.17, 2.85, and 0.028, respectively. As for PFS, the area under the curve (AUC) was 0.693 for FAR, 0.690 for FLR, and 0.661 for FHR, respectively. The AUC was 0.770, 0.692, and 0.715 accordingly for OS. The groups with lower FAR, FLR, and FHR were significantly associated with prolonged PFS and OS (p < 0.05). In patients with metastasis, the lower FAR group was correlated with significantly longer PFS and OS (p = 0.022 and 0.002, respectively). The FLR was an independent predictor of PFS in pNEN patients, and the FAR was a predictor of OS. FAR was an independent indicator of PFS in patients with metastasis. Conclusion: Preoperative FAR, FLR, and FHR are effective in predicting the prognosis of pNEN patients and detecting the synchronous metastases.

Objective: The current study aimed to delineate the relationship of furin with inflammation while cervical intraepithelial neoplasia progresses to cancer. Study Design:This cross-sectional study included 81 women who required colposcopic examinations. The study groups were formed based on pathological results: Group I included women with cervical intraepithelial neoplasia (CIN) I (n=30); Group II included women with CIN II-III (n=28); and Group III included women with cervical cancer (CC) (n=23). Furin, ki-67, and p16 levels were evaluated based on immunostaining intensity. The inflammatory indices were calculated parallel with the literature from routine blood samples retrieved within one week before the procedure. Results:Furin expression gradually increased from CIN I to CIN II-III and from CIN II-III to CC, respectively (p < .001, p = .005). The NLR, MLR, PLR, and SII were significantly higher in the CC group (p < .001). ROC curve analysis unveiled that NLR, MLR, PLR and SII predicted the presence of CC with a cutoff value of 2.39 for NLR (sensitivity: 91.3%, specificity: 63.8%, AUROC: 0.79, p < .001); a cutoff value of 0.27 for MLR (sensitivity: 78.3%, specificity: 72.4%, AUROC: 0.77, p = .009); a cutoff value of 123 for PLR (sensitivity: 100%, specificity: 41.4%, AUROC: 0.70, p = .04); and a cutoff value of 747 for SII (sensitivity: 69.6%, specificity: 90.7%, AUROC: 0.71, p = .014). Conclusion:Furin expression increased gradually in parallel to the severity of cervical intraepithelial neoplasia. The inflammatory indices were higher in the presence of CC and denoted good discrimination ability for predicting cervical cancer.

Previous studies generally reckon that the full converter-base wind power generation (FCWG) is a ’decoupled’ power source from the grid, which hardly participates in electromechanical oscillations. However, it is found recently that strong interaction could be induced which might incur severe resonance incidents in electromechanical dynamic timescale. In this paper, the participation of FCWG in electromechanical dynamics is extensively investigated, and particularly, an unusual transition of electromechanical oscillation mode (EOM) is uncovered for the first time. The detailed mathematical models of open-loop and closed-loop power systems are firstly established, and modal analysis is employed to quantify the FCWG participation in electromechanical dynamics, with two new mode identification criteria, i.e., FCWG dynamics correlation ratio (FDCR) and quasi-electromechanical loop correlation ratio (QELCR). On this basis, the impact of different wind penetration levels and controller parameter settings on the participation of FCWG is investigated. It is revealed that if an FOM has a similar oscillation frequency to the system EOMs, there is a high possibility to induce strong interactions between FCWG dynamics and system electromechanical dynamics of the external power systems. In this circumstance, an interesting phenomenon may occur that an EOM may be dominated by FCWG dynamics, and hence is transformed into a quasi-EOM, which actively involves the participation of FCWG quasi-electromechanical state variables.

It is known that the elastic characteristics of polyamides change with increasing temperature, in particular, the Young's modulus decreases significantly. This fact is practically not taken into account in design calculations of metal-polymer plain (MP) bearings, operating under conditions of the boundary and dry friction. The purpose of the study is the analysis of the effect of temperature on the change of the Young's modulus and, accordingly, the contact strength and triboresource according to the developed method of calculating MP bearings. MP bearings with a bushing made of polyamide PA6 reinforced with glass or carbon dispersed fibers were investi-gated. Quantitative and qualitative regularities of change of the maximum contact pressures and resource of the bearings at temperature increase under conditions of boundary and dry friction are established. The pressures in the bearing bushing made of PA6+30GF will be lower than for the bushing made of PA6+30CF. The resource of the bushing made of PA6+30CF will be significantly greater than for PA6+30GF. For thermoplastic polymers, the increase in temperature will have a useful practical effect due to the decrease in the rigidity of the polymer composites of the bearing bushing.

A Savonius wind turbine is one of the simplest vertical-axis turbines. Several researchers have been attracted to it because of its simple structure, low noise, appropriate torque, and independence from wind direction. SR3345 and SR5050 blade profiles will be investigated for their effects on the performance of Savonius wind turbines. First, the fabricated wind turbine is placed in front of an open circuit wind tunnel with a velocity of 6 m/s. Furthermore, governing relationships are used to calculate power and torque coefficients as well as tip speed. In this study, the power and torque coefficients of the turbine are compared with the two profiles considered based on overlap ratios between 0 and 0.3. Despite its increased stability, the central shaft reduced the power coefficient of the turbine. For blade SR3345, the best performance occurs at tip speed ratios of less than 1, while for blade SR5050, the best performance occurs at higher tip speed ratios. Both blades SR3345 and SR5050 achieve the highest power coefficients at overlap ratios of 0 and 0.18 when a central shaft is present.

Isokinetic testing of the knee joint is the “gold standard” in strength assessment in sport especially in soccer, where it is part of pre-season screening to establish norms in case of injuries. There are many devices on the market that make it difficult to use of normative data. Isokinetics literature in females’ soccer players is scarce in comparison to males. Furthermore, evaluation protocols strongly differ from each other, using different ranges of speeds, movement patterns and output data. Thus, it is difficult for the researcher and the clinician to choose a correct protocol for isokinetic evaluation in female soccer players. The indexes of isokinetic performance that are widely accepted are the hamstring/quadriceps (H/Q) ratio and dominant/non-dominant (D/ND) ratio as reference. In this review are highlighted some common features of isokinetic testing in female soccer players of different levels of qualification. From this study, it emerges that, for a reliable test, 3 reps at the speed of 60°/sec in knee flexion/extension is preferable due to the high reliability and that an optimal H/Q ratio in healthy female soccer players of different level of qualification and age is 50%, while the interlimb differences (D/ND) should be below 10%.

As in any other plant, in the grapevine roots play a vital role in terms of anchorage, uptake of water and nutrients, as well as storage and production of chemicals. Their behaviour and development depend on various factors, namely rootstock genetics, soil physical and chemical features, field agronomic practices. Canopy management, involving techniques such as defoliation and pruning, could greatly influence root growth. To date, most of the studies on grapevine winter pruning have focused on the effects on yield and quality of grapes, achievable by using different pruning systems and techniques, while the knowledge of root distribution, development, and growth in relation to winter pruning is still not well understood. In this contest, the purpose of this study was to investigate the effect of winter pruning on the root system of field-grown Vitis vinifera cv. Pinot Gris grafted onto rootstock SO4. We compared two pruning treatments (pruning-P and no pruning-NP) and analysed the effect on root distribution and density, root index and on the root sugar reserves. Root data were analysed in relation to canopy growth and yield, to elucidate the effect of winter pruning on the root/yield ratio. Our data indicated that winter pruning stimulated the root growth and distribution without compromising canopy development, while no-pruning treatment produced less growth of roots but a larger canopy. Information regarding root growth and root canopy ratio is important as it gives us an understanding of the relationship between the aerial and subterranean parts of the plant, how they compete, and finally, offers us the possibility to ponder on cultural practices.

Rapeseed (Brassica napus) is one of the most important oil crops in the world; however, drought significantly curtails its growth and productivity. Identifying drought-tolerant germplasm is an efficient and low-cost strategy for addressing water shortages. Using water loss ratio (WLR) as an index of drought tolerance, we screened a panel of 265 B. napus lines. We identified eight low-WLR and six high-WLR accessions, which were regarded as drought-tolerant and drought-sensitive, respectively. Further validated these selected accessions at the seedling stage under drought-stress conditions. The drought-tolerant accessions had significantly greater fresh and dry weights under drought stress than the drought sensitive accessions. Using RT-qPCR, we showed that a set of previously reported drought-adaptive marker genes were expressed at higher levels in the drought-tolerant lines than in the drought-sensitive lines. These results indicated that the drought-tolerant genotypes could be identified from natural populations using WLR. Then, we performed a genome-wide association study to identify loci harboring single nucleotide polymorphisms (SNPs). A total of 139 SNPs were significantly associated with the WLR, of which chromosome A10 harbored the largest number. Furthermore, four putative candidate genes were selected by combining the SNP–WLR association results and transcriptional expression data with the changes in drought tolerance. Thus, we have identified two drought-tolerant B. napus cultivars and uncovered genome-wide variation differentiating B. napus lines related to WLR, in addition to providing insights for further research into WLR-related drought mechanisms.

Upper Blue Nile basin (UBNB) is the water tower of Ethiopia and downstream countries. It contributes significant moistures to the surrounding atmosphere. However, the contribution of the moisture from the basin to the precipitation in the area is not well documented. Therefore, this paper is aimed at seasonal variation of upper Blue Nile basin moisture budget and the global moistures in the role of temporal and spatial precipitation variability. To this end, we used European Centre for Medium-range Weather Forecast (ECMWF) data from 1979-2017. The UBNB moisture contributed precipitation in the central parts of the study area during the summer season, while in spring; it contributed in southern part of the study area. Northwest part of the study area got precipitation from the basin moistures during autumn season. The recycling ratios for four seasons (summer, autumn, spring and winter) were 9.70%, 16.33%, 19.01%, and 35.30% respectively. The maximum amount of precipitation is extracted from the local moistures during winter season. The annual average value of recycling ratio was found 20.11%. Hence, we concluded that UBNB moisture budget had lesser contribution of precipitation over the study area. It rather contributed a significant precipitation to the neighboring countries such as Egypt and Sudan. Further studies on moisture budget are required to explain this phenomenon in the context of Ethiopia.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

The scale and accessibility of passive global surveillance have rapidly increased over time. This provides an opportunity to calibrate the performance of models, algorithms, and reflectance ratios between remote sensing devices. Here we test the sensitivity and specificity of Eucalypt chlorophyll-a reflectance ratio (ECARR) and Eucalypt chlorophyll-b reflectance ratio (ECBRR) to remotely identify eucalypt vegetation in Queensland, Australia. We compare reflectance ratio values from Sentinel-2 and Planet imagery across four sites of known vegetation composition. All imagery was transformed to reflectance values and Planet imagery was additionally scaled to harmonize across Planet Scenes. ECARR can identify eucalypt vegetation remotely with high sensitivity, but shows low specificity and is impacted by the density of the vegetation. ECBRR reflectance ratios show similar sensitivity and specificity when identifying eucalypt vegetation but with values an order of magnitude smaller than ECARR. We find that ECARR was better at identifying eucalypt vegetation in the Sentinel-2 imagery than Planet imagery. ECARR can serve as a general chlorophyll indicator but is not a specific index to identify Eucalyptus vegetation with certainty.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

Background. IgA nephropathy (IgAN) is associated with chronic inflammation. Platelet-related parameters, such as platelet (PLT) count, platelet-to-albumin ratio (PAR) and platelet-to-lymphocyte ratio (PLR), were examined as potential prognostic indicators for renal and cardiovascular (CV) outcomes in IgAN. Methods. 150 IgAN patients were devided into two groups based on the cut-off value of PAR. All-cause mortality, major CV events and end-stage renal disease were the primary combined endpoints. Secondary endpoints, such as CV or renal endpoints, were also analyzed separately. Results. The patient’s mean age was 43.7 ± 13.5 years, and the follow-up time was 124 ± 67 months. The K-M curve showed that PLR, PAR and PLT were strongly associated with primary combined (p = 0.002, p = 0.004, p = 0.001) and renal outcomes (p < 0.001, p < 0.001, p < 0.001), but not with CV outcomes in IgAN. However, when combined with left ventricular hypertrophy (LVH) or metabolic syndrome (MetS) PAR was found to be a significant predictor of both primary (p < 0.001, p < 0.001) and secondary outcomes (p = 0.001 and p = 0.038; p = 0.001 and p = 0.015). Additionally, PLR correlated with microalbuminuria (r = -0.165, p = 0.033) and LVH (r = -0.178, p = 0.025), while PLT correlated with eGFR (r = 0.158, p = 0.040). Conclusion. Elevated PAR and PLR may predict progression to end-stage kidney disease, but in combination with LVH and MetS, they showed CV events also in IgAN. The determination of PAR and PLR can be useful and cost-effective parameters for assessing both cardiovascular and renal risks in CKD.

Background: The aim of this study has been to investigate if inflammatory biomarkers such as the systemic immune-inflammation index (SII), neutrophil to lymphocyte ratio (NLR) and platelet to lymphocyte ratio (PLR) have any correlation with the recurrence of pleomorphic adenomas (PA) in patients afflicted by this disease. Methods: A retrospective multicentre study involving two Italian centres, the Maxillofacial Sur-gery at the Policlinico Federico II in Naples and the ENT and Maxillofacial Surgery at the IRCCS G. Pascale National Cancer Institute in Naples, has been performed. The study, involving 608 pa-tients who had received a diagnosis of PA, was conducted between January 2000 and January 2020. A Receiver Operating Characteristic (ROC) curve was used to calculate the optimal cut-off values for the SII, PLR and NLR. A linear regression model (LRM) and a non-linear logistic re-gression model (NLRM) were realized with respect to the NLR, PLR and SII. Results: The highest performance was achieved by the NLR (cut-off 2.960) with the AUC = 0.91, with an accuracy of 96.1%, sensitivity of 78.4% and specificity of 97.2%, PPV = 64.4% and NPV = 98.6%. The LRM and NLRM including all the haematological parameters did not increase the per-formance in terms of recurrence detection. Conclusion: The NLR is an excellent support tool in predicting the recurrence of PA with a cut-off of 2.960. It can be a good reference point for surgical decision-making and follow-up in clinical practice.

Cloud Computing is a promising and emerging technology that is rapidly being adopted by many IT companies due to a number of benefits that it provides, such as large storage space, low investment cost, virtualization, resource sharing, etc. Users are able to store a vast amount of data and information in the cloud and access it from anywhere, anytime on a pay-per-use basis. Since many users are able to share the data and the resources stored in the cloud, there arises a need to provide access to the data to only those users who are authorized to access it. This can be done through access control schemes which allow the authenticated and authorized users to access the data and deny access to unauthorized users. In this paper, a comprehensive review of all the existing access control schemes has been discussed along with analysis. Keywords: role-based access control, attribute-based access control, attribute-based encryption

Extreme-mass-ratio inspirals (EMRIs) are significant observational targets for spaceborne gravitational wave detectors, namely, LISA, Taiji, and Tianqin, which involve the inspiral of stellar-mass compact objects into massive black holes with a mass range of approximately 104∼107M⊙. EMRIs are estimated to produce long lived gravitational wave signals with more than 105 cycles before plunge, making them an ideal laboratory for exploring the strong-gravity properties of the spacetimes around the MBHs, stellar dynamics in galactic nuclei, and properties of the MBHs itself. However, the complexity of the waveform model, which involves the superposition of multiple harmonics, as well as the high-dimensional and large-volume parameter space, make the fully coherent search challenging. In our previous work, we proposed a 10-dimensional search using Particle Swarm Optimization (PSO) with local maximization over the three initial angles. In this study, we extend the search to an 8-dimensional PSO with local maximization over both the three initial angles and the angles of spin direction of the MBH where the latter contribute a time independent amplitude to the waveforms. Additionally we propose a 7-dimensional PSO search by using a fiducial value for the initial orbital frequency and shifting the corresponding 8-dimensional Time Delay Interferometry responses until a certain lag returns the corresponding 8-dimensional log-likelihood ratio maximum. The reduced dimensionality likelihoods enable us to successfully search for EMRI signals with duration of 0.5 years and signal-to-noise ratio of 50 within a wider search range than our previous study. We discuss further developments, such as using a hierarchical search to narrow down the search ranges of certain parameters, and applying Graphics Processing Units to speed up the code. These advances aim to improve the efficiency and accuracy of the EMRI search algorithm.

Polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) exist in the atmosphere in the vapor and particulate phases, as well as in the solubilized form in fog/rain/cloud waters. They are abundant pollutants and are known for their acute and chronic toxicity. In the current paper, fogwater samples are collected during 42 events between 2015 and 2021 at four sites (Strasbourg, Geispolsheim, Erstein, Cronenbourg) in the Alsace region with different topological characteristics. PAHs and PCBs are extracted using the liquid-liquid extraction (LLE) supported on a solid cartridge (XTR Chromabond), and then analyzed by gas-chromatography tandem mass spectrometry (GC-MS/MS). Total PAHs and PCBs concentration in fog samples varied between 0.58 and 6.7 µg L-1 (average of 2.70 µg L-1), and 0.14 and 15.5 µg L-1 (average of 2.75 µg L-1). Low molecular weight (LMW) predominant and highly detectable over high molecular weight PAHs by at least 1.6 times, while pentachloro-biphenyls are the dominant PCB congener accounting for at least 50% of the total fraction. PAHs and PCBs concentrations have increased over sampling years at all sites, except a slight decrease in PCBs level at Geispolsheim. Diagnostic ratio analysis suggested that diesel and fossil fuel combustion are the dominant contributors to PAHs in Alsace

Swarm intelligence (SI) methods are nature-inspired metaheuristics for global optimization that exploit a coordinated stochastic search strategy by a group of agents. Particle Swarm Optimization (PSO) is an established SI method that has been applied successfully to the optimization of rugged high-dimensional likelihood functions, a problem that presents the main bottleneck across a variety of gravitational wave (GW) data analysis challenges. We present results from a first application of PSO to one of the most difficult of these challenges, namely, the search for Extreme Mass Ratio Inspiral (EMRI) in data from future spaceborne GW detectors such as LISA, Taiji, or Tianqin. We use the standard Generalized Likelihood Ratio Test formalism, with minimal use of restrictive approximations, to search 6 months of simulated LISA data and quantify the search depth, in signal-to-noise ratio (SNR), and breadth, in the ranges of the EMRI parameters, that PSO can handle. Our results demonstrate that a PSO-based EMRI search is successful over a search region that is in the ballpark of the one that current hierarchical schemes can identify. Directions for future improvements, including computational bottlenecks to be overcome, are identified.

This paper discusses the theoretical and experimental correlations between fatigue and static strength statistical distributions. We use a two-parameter residual strength model that obeys the qualitative Strenght-Life Equal-Rank (SLERA) assumption for guidance. The modeling approach consists of recovering the model's parameters by best fitting the constant amplitude (CA) fatigue data at a given stress ratio, R, and the experimental Weibull parameters of the static strength distribution function. Once the model's parameters are fixed, its capabilities, potential, and limits are discussed by comparing its predictions with residual strength and fatigue data obtained at different stress ratios, R. Moreover, from a preliminary analysis, the theoretical extension of the model's capabilities to variable amplitude loadings is conceptualized. The application of Miner's rule is also discussed and compared with a new damage rule to analyze the fatigue responses under variable amplitude loadings.

Background and aim: The albumin-globulin ratio (AGR) is one of the indicators of inflammation and immunity and it has a prognostic significance in many malignant diseases. Previous studies have shown the relationship between inflammatory mediators and POPF. This study aimed to evaluate the relation of AGR, which is a relatively new indicator, with postoperative pancreatic fistula (POPF). Methods: Pancreaticoduodenectomy (PD) patients between 2017 and 2020 were retrospectively analyzed and divided into two groups as those with and without clinically relevant POPF (CR-POPF). They were compared in terms of preoperative-postoperative AGR and clinicodemographic characteristics. AGR was calculated as Albumin / (Total protein-albumin) and the cutoff point for AGR was determined according to Youden’s index. Results: CR-POPF developed in 21% of 121 patients who underwent PD. There was no difference between the groups in terms of age, gender, comorbid disease status, pancreatic duct width, and anastomosis technique. Preoperative and postoperative day-3 (POD3) albumin levels and AGR were found to be significantly lower in the CR-POPF group. Multivariate analysis showed that AGR and pancreatic tissue stiffness are independent risk factors for the development of POPF. Conclusions: Low AGR is an independent risk factor for the development of CR-POPF. To reduce the incidence of POPF, this ratio should be tried to be kept at an optimal level.

The article deals with auxetic structures made on the basis of suitably connected rigid rotating squares (from Grima and Evans), with axes of rotation on the squares’ surface. The geometric model and the resulting relationships that allow for the determination of Poisson’s ratio are considered in detail. It is demonstrated that changing the rotation axis position does not affect the negative Poisson’s ratio, equal to -1. The models built confirm the initial considerations and can offer new application possibilities.

Recent studies indicate that the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) aboard the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) satellite provides valuable information about ocean phytoplankton distributions. CALIOP’s attenuated backscatter coefficients, measured at 532 nm in receiver channels oriented parallel and perpendicular to the laser’s linear polarization plane, are significantly improved in the Version 4 data product. However, due to non-ideal instrument effects, a small fraction of the backscattered optical power polarized parallel to the receiver polarization reference plane is misdirected into the perpendicular channel, and vice versa. This effect, known as polarization crosstalk, typically causes the measured perpendicular signal to be higher than its true value and the measured parallel signal to be lower than its true value. Therefore, the ocean optical properties derived directly from CALIOP’s measured signals will be biased if the polarization crosstalk effect is not taken into account. This paper presents methods that can be used to estimate the CALIOP crosstalk effects from on-orbit measurements. The global ocean depolarization ratios calculated both before and after removing the crosstalk effects are compared. Using CALIOP crosstalk-corrected signals is highly recommended for all ocean subsurface studies.

While sex ratios at birth (SRB) have been shown to vary within and across populations, after over a century of research, explanations have remained elusive. A variety of ecological, demographic, economic, and social variables have been evaluated, yet their association with SRB has been equivocal. Here, in an attempt to shed light on this unresolved topic within the literature, we approach the question of what drives variation in SRB using detailed longitudinal data spanning the frontier-era to the early 20th century in a US population. Using several measures of environmental harshness, we find that fewer boys are born during challenging times. However, these results hold only for the frontier-era and not into a period of rapid industrialization. We argue that the mixed state of the literature may result from the impact and frequency of exogenous stressors being dampened in post-industrial societies.

The goal of this paper is to explore the relationship between the specific non-performing loan ratio (NPL ratio) and the corresponding impact on the bank’s profitability and lending behavior. It also seeks to investigate the macroeconomic impacts of economies with excessively high NPL ratios as well as the efficacy and impact of alleviation measures used by banks and governments around the world to help facilitate a decrease in high NPL ratios. The possible implications and effects of the COVID-19 pandemic on NPL ratios is also addressed in this paper. It is found that when excessively high NPL ratios go unaddressed, the economy tends to suffer. On the other hand, this study shows that when measures are taken to reduce or eliminate the high NPL ratios, economic performance improves, and the reduction has a clear positive impact on the economy.

Abstract: A two-year study of pearl millet-groundnut cropping systems across two fertilizer levels was conducted at the INRAN/TARNA research station in Maradi, Niger in the Sahelian zone of West Africa. The objective of this study was to identify the best cropping system with and without fertilizer application to optimize pearl millet and groundnut yields, land use efficiency, and economics as measured by value-to-cost ratio. The experiment was conducted with three replications, and ten treatments combination of five pearl millet and groundnut cropping systems (pearl millet and groundnut sole crops, and three pearl millet – groundnut intercrops), and two fertilizer levels. Sole cropping produced the highest pearl millet grain by over 300 kg ha-1 and groundnut pod yields by over 500 kg ha-1, but all the intercropping systems had a LER above 1.0 with land use efficiency increased by 19 to 41%, also intercropping increased diversity, and reduced risk. Fertilizer application increased yields in all cropping systems by 200 to 600 kg ha-1. Government subsidy increased the value-to-cost ratio by 0.5 to 2, 5 units, and was required for economic response for pearl millet sole and intercrops in 2022. The groundnut sole cropping system had the greatest economic response to fertilizer application. Based on the risky environment and multiple end uses needed by producers, the intercrop system M-G: 1:3:1 with fertilizer application is usually the best option to optimize pearl millet and groundnut production.

Neutrophil to lymphocyte ratio (NLR) is a promising predictive and prognostic factor in breast cancer. We investigated its ability to predict disease-free survival (DFS) and overall survival (OS) in patients with luminal A or luminal B-HER2-negative breast cancer who received neoadjuvant chemotherapy (NACT). Pre-treatment complete blood cell counts from 168 consecutive patients with luminal breast cancer were evaluated to assess NLR. The study population was stratified into NLRlow or NLRhigh according to a cut-off value established by receiving operator curve (ROC) analysis. Data on additional pre- and post-treatment clinical-pathological characteristics were also collected. Kaplan-Meier curves, log-rank tests, and Cox proportional hazards models were used for statistical analyses. Patients with pre-treatment NLRlow showed a significantly shorter DFS (HR 6.97, 95% CI 1.65-10.55, p= 0.002) and OS (HR 7.79, 95% CI 1.25-15.07, p= 0.021) compared to those with NLRhigh. Non-ductal histology, luminal B subtype, and post-treatment Ki67≥ 14% were also associated with worse DFS (p= 0.016, p= 0.002, and p= 0.001, respectively). In multivariate analysis, luminal B subtype, post-treatment Ki67≥ 14%, and NLRlow remained independent prognostic factors for DFS, while only post-treatment Ki67≥ 14% and NLRlow affected OS. The present study provides evidence that pre-treatment NLRlow helps identify women at higher risk of recurrence and death among patients affected by luminal breast cancer treated with NACT.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Background Telomere shortening is related to aging and unfavourable health outcomes. Obesity and metabolic diseases are important factors for accelerating aging. This study aimed to find out the association between obesity, metabolic disease, and telomere length in metabolically healthy adults. Methods 237 adults were enrolled with written consents at a health promotion centre of a tertiary hospital from February 2014 to March 2015. After excluding 99 subjects who met the exclusion criterion, a total of 130 metabolically healthy subjects were selected for final analysis. The subjects were divided into quartile groups according to the telomere lengths of their oral mucosal cells. Results The subjects consisted of 66 (50.8%) males with a mean age of 58.59 years. The body mass index (BMI, kg/m2) increased significantly along with the quartile groups (Q1, 23.00; Q2, 23.96; Q3, 23.70; Q4, 25.20; P-for trend=0.008). Waist circumference (WC, P-for trend=0.022), waist-to-hip ratio (WHR, P-for trend=0.005), and waist-to-height ratio (WHtR, P=0.001) also increased along with the quartile groups. Obesity prevalence (BMI ≥25 kg/m2), abdominal obesity (WC ≥90 cm for men, ≥85 cm for women), WHR 〉1.0 for men or 〉0.85 for women, and WHtR ≥0.5 increased significantly as the telomere length increased (P-for trend <0.05). After adjusting for covariates, the ORs for each obesity markers increased as the telomere length increased (P-for trend <0.05); and the ORs of WHtR were especially meaningful (Q1, 1.00; Q2, 2.53; Q3, 2.97; Q4, 7.81; P-for trend = 0.001). There were no significant trends for metabolic syndrome and its components along with the prevalence of fatty liver disease. Conclusion Obesity markers and telomere length had significant positive correlation despite the established theory. The obesity paradox may exist in metabolically healthy adults with regard to telomere length, However, further studies with larger sample sizes for the association between obesity and telomere length are needed.

The article presents comparative results from 5 categories of animals (4 samples originating from pigs, 2 from cows, 1 from chicken, 1 from ostriches, 1 from horses, samples quantified with A, B, C, D, E, F, G, H, I). These samples were collected from large, medium and small (family) farms. The results were validated by the biogas production generated by the respective samples, using the Automatic Methane Potential Test System (AMPTS II) bio-processor. The largest amounts of biogas (2,464.5 Nml, 2,262.0 Nml) were recorded for the samples from pig farms (Sample B and Sample D), whereas the lowest values were obtained in the case of Sample A (414.1 Nml) and Sample C (558.3 Nml). The heavy metals analyzed in the article are Zn, Cu, Fe, Mn, Ca, K, As. The results corroborate that the C/N ratio can also vary to values lower than 20-30, without affecting the biogas production process, and the heavy metal content must be known especially for the full management of the wastes. All final data presented in the article are based on repeated, triplicate experiments, with less as 2% deviation between data.

Ethiopia is one of the countries with the highest level of malnourishment of lactating mothers in sub-Saharan Africa. However, different communities produced different foods solely for lactating mothers. "Shameta" is one of the cereal-based fermented cultural foods exclusively produced for lactating mothers with the perception that it would support the health, strength, and recovery of mothers. This study investigated the effects of fermentation time and blending ratio on the nutritional quality of "Shameta." Three levels of blending ratio of ingredients (Maize-Barley-Fava bean) and three levels of fermentation times were laid down in a completely randomized design (CRD). The study showed that lactic acid bacteria were the dominant group, followed by yeasts. Notably, the ingredient formulation ratio of Maize-Barley-Fava bean (81:5:5) in all fermentation times (8, 10, and 12 days) results in the highest LAB dominance with the highest crude fat (13.23 g/100g) content. However, the highest crude protein (16.56 g/100g) and mineral contents were observed in a ratio mix of 66:10:15 fermented for 12 days. The nutritional quality of culturally prepared Shameta can be improved by optimizing fermentation time and ingredient compositions for better recovery, strength, and health of lactating mothers.

The purpose of this study was to determine the income, costs and revenue of the Gontor Putri 3 bakery. Want to know the efficiency of the bakery business in Karangbanyu Regency. The method used in this research is analytical descriptive by conducting a survey. The data used in this research is primary data. Data collection techniques use observation, interviews and documentation, while the process of analysis is quantitative descriptive. Using the R/C ratio, a value of 1.72 per month is obtained. This value indicates that the bakery factory in Karangbanyu is efficient because the value is more than one.

On the basis of the golden ratio and the compasseses, every angle was divided into three equal parts. In general, it has been proven that the problem of triangulation of an angle cannot be solved on the basis of the golden ratio and the expanding of the angle. The relationship of golden relativity with Pi number and Euler's number has not been investigated to solve impossible problems. According to the investigation of events in six-dimensional space-time, with the simultaneous movement of two arms of the compasses based on the golden ratio, every angle was divided into three equal parts. The growth rate based on the golden ratio is the key to solving the most intractable mathematical and physical problems.

Frontotemporal dementia (FTD) is the second most common form of presenile dementia; however, its diagnosis has been poorly investigated. Previous attempts to diagnose FTD using quantitative electroencephalography (qEEG) have yielded inconsistent results in both spectral and functional connectivity analyses. This study aimed to introduce an accurate qEEG marker that could be used to diagnose FTD and other neurological abnormalities. We used open-access electroencephalography data from OpenNeuro to investigate the power ratio between the frontal and temporal lobes in the resting state of 23 patients with FTD and 29 healthy controls. Spectral data were extracted using a Fast Fourier Transform in the delta (1–4 Hz), theta (4–8 Hz), alpha (8–13 Hz), beta (13–32 Hz), and gamma (32–45 Hz) bands. We found that the spectral power ratio between the frontal and temporal lobes is a promising qEEG marker of FTD. Frontal/temporal (F/T) theta/alpha, alpha/theta, al-pha/gamma, and gamma/alpha showed a consistently high discrimination score for the diagnosis of FTD for different parameters and referencing methods. The study findings can serve as reference for future research focused on diagnosing FTD and other neurological anomalies.

Retention mechanisms in HILIC have been investigated and reported in literature. However, the current understanding of the retention mechanisms is qualitative and lacks quantitative details. Previously, mechanism elucidation was based on indirect evidence, and unambiguous assignment of retention mechanisms has not been reported based on direct data. This study aims to quantitatively determine the contributions of two major retention mechanisms in HILIC, hydrophilic partitioning and surface adsorption to the overall retention of neutral compounds. Using the methodologies we developed previously, the phase ratio for adsorbed water layer and distribution coefficients were measured and used to calculate the retention factors attributed to hydrophilic partitioning. The methodology allows the determination of the contribution of surface adsorption simultaneously. The evaluation of five test compounds demonstrates that the retention may be controlled by hydrophilic partitioning, surface adsorption or both depending on compound characteristics. Quantitative assessment of retention mechanisms also makes it possible to better understand the effect of acetonitrile on retention in HILIC.

At present, aeroponic control is mainly regulated according to the environmental factors of aeroponics, such as the temperature, humidity, light intensity, carbon dioxide concentration, pH, and electrical conductivity (EC) of the nutrient solution. There is a lack of knowledge available in the literature for an aeroponic control system for plant growth information as the primary feedback signal. Therefore, a fuzzy logic-controlled aeroponics system was developed for the growth of lettuce as a feedback signal. After designing, the effectiveness test of system was performed with experiment having three treatments T1 (180C), T2 (220C) and without control (CK). The results show an increasing trend in shoot length, root length, and shoot area over time in all treatments. In terms of shoot area, the maximum of 345 cm² was observed in the T1 treatment, while the CK treatment had a minimum of 241.8 cm². Statistical analysis indicated that the T1 and T2 treatments were not significantly different, but both were significantly different from the CK treatment. The study demonstrates the effectiveness of the fuzzy logic control system and an 18°C nutrient solution temperature, resulting in improved lettuce growth and reduced root-to-shoot ratio. The findings suggest the potential of using fuzzy logic control in aeroponics for optimized cultivation outcomes.

The lattice reduction aided(LRA) algorithm has attracted widely attention of researchers in MIMO systems because of its low complexity to achieve full diversity. However, most lattice reduction auxiliary algorithms do not directly improve system performance. In this paper, a modified lattice reduction successive interference cancellation (SIC) algorithm is proposed for MIMO OFDM system mild changing the complexity of LRA algorithm. At present, the MMSE SQRD algorithm has the problem of regarding too much useful signals as the residual interference which cannot be cancelled by successive interference cancellation. Since the diagonal elements of useful signals are non-zero, the components of the symbols to be detected still present in the interference term, treating all the signals as interference will be resulted in performance loss. To solve this problem, the modified matrix is proposed.by moving this symbol component into the signal term, the proposed algorithm can provide the better performance than MMSE SQRD algorithm. The analysis shows that the LRA-MMSE-SIC algorithm of proposed in this paper significantly improves the system performance with mild increasing the complexity. The simulation results show that the performance of the proposed algorithm is improved by 1dB and 8dB compared with the comparison algorithm when the bit error rate is 10−3.

Introduction: Studies conducted in real-life scenarios on vaccine protection against COVID-19 constitute an important global priority, but one that is currently mostly neglected in low- and middle-income countries such as Angola. Here, we analyze for the first-time vaccine protection against COVID-19 in a real-life scenario after 6 months of implementing a multi-vaccination plan in Angola, providing estimation of odds ratios in vaccinated individuals and vaccine efficacy against infection by SARS-CoV-2 in a period that coincided with the identification of the Omicron variant in the country. Methods: We used a negative test case-control design to assess the effectiveness of vaccination against confirmed SARS-CoV-2 infection. A total of 4.232 vaccinated and unvaccinated individuals with the result of a rapid antigen diagnostic test against SARS-CoV-2 performed from December 27 to 28, 2021 were included in the study. Data were extracted from the Digital Vaccination Record Platform (Rediv) of the Ministry of Health of Angola. All ethical procedures related to the authorization necessary to carry out the study were followed. Statistical analyzes were performed using version 7.5.2.0 of CDC's Epi Info. Frequency distributions and measures of central tendency were used to characterize the study universe. The general and sex-adjusted and age-adjusted odds ratios, were evaluated by comparing the chances of vaccination between cases and controls, and their associated 95% CI, which were calculated using the Mantel-Haenszel stratification method. The risk classification of Axel Kroeger, Piscoya and Alarcon was used to interpret the odds ratio. The Breslow-Day statistic was used to assess the homogeneity of the odds ratios. Vaccine efficacy was calculated using the odds ratio applying the accepted statistical vaccine efficacy formula:(1 − odds ratio) × 100. For all estimates, a P value < 0.05 was considered statistically significant. Results: The population consisted of 63.63% male and 36.37% female. The mean age was 36 years with a standard deviation of 13. 83. Regarding vaccination status, 83.27% of individuals were vaccinated and 16.73% were unvaccinated, with 21.81% positive and 78.19% negative for SARS -CoV-2. The odds of SARS-CoV-2 infection were 0.85 (95% CI 0.70 – 1.03) times lower in vaccinated compared to unvaccinated individuals, with P=0.09. The overall vaccine efficacy (VE) was 15% (95% CI -3 – 30). Conclusion: There was no statistically significant decrease in the chances of SARS-CoV-2 infection in vaccinated versus unvaccinated individuals. However, the overall vaccine efficacy was 15%.

(1) Background: The CEO message of hospital homepage contain various contents such as the hospital's future vision, promises with customers, upgraded services and public activities. The CEO’s message of the homepage includes non-financial information as well as financial information of corporates. Also, it provides useful information for not only company's goals and vision but also firm performance and strategies for the future. This study aims to investigate associations between CEO’s message of hospitals homepages and financial status. We used the balanced scorecard frame to analyze what content on the hospital's homepage is related to the hospital's various financial ratios. (2) Methods: We adopt a text mining method to extract significantly repeated keywords from the CEO’s message of hospital website. And we classify these keywords by a balanced scorecard frame. To examine the relationship between keywords of CEO’s message of the hospital homepage and hospital’s financial ratio, T-test is conducted for the difference in the TF-IDF (Term Frequency is Divided by Inverse Document Frequency) mean of the home page contents and its relationship with the views of the balanced scorecard framework. (3) Results: According to empirical results on 65 samples collected from local hospitals, there are some significant relationship between the qualitative content of the hospital's homepage and the quantitative financial ratio that indicates profitability, activity, leverage, liquidity, and transfer to essential business fund (EBF) income. (4) Conclusions: The introduction section of a homepage is most accessible to customers, containing the aims and ideals of hospitals and reflecting their values and visions [1]. In addition, in view of financial status, they can either emphasize financial strength or focus on other areas to mask weakness of financial information. This study reminds us of the importance of hospital website’s disclosure, and it can be inferred from the financial status of the hospital. It also highlights the need for harmonization between quantitative data, financial statements, and qualitative data, CEO’s messages. (5) Implications: To our best knowledge, this paper is the first research attempting to investigate the relation between text of hospital homepage and financial ratio of hospital through text mining technique and balanced scorecard frame. Hospitals take a crucial part in a country’s welfare and healthcare backbone industry. Nevertheless, in many countries, hospital organization sectors tend to remain a source of critical fiscal deficits due to its ineffective and sloppy management. We expect that the result of this paper can provide hospital managers to useful information.

In attempting to predict the further course of the novel coronavirus (COVID-19) pandemic caused by SARS-CoV-2, mathematical models of different types are frequently employed and calibrated to reported case numbers. Among the major challenges in interpreting these data is the uncertainty about the amount of undetected infections, or conversely: the detection ratio. As a result, some models include assumptions about the percentage of detected cases among total infections while others completely neglect undetected cases. Here, we illustrate how model projections about case and fatality numbers vary significantly under varying assumptions on the detection ratio. Uncertainties in model predictions can be significantly reduced by representative testing, both for antibodies and active virus RNA, to uncover past and current infections that have gone undetected thus far.

There is high prevalence of hypertension and is rapidly increasing around the world, despite the intervention programme implemented, this study aimed at estimating the prevalence rate, test of association between hypertension and risk factors and model hypertension rate. Data used was obtained from the health record of Federal Medical Centre, Keffi from January 2016 – January 2019. Ordinal logistic regression model was used; Model Fitting Information, Goodness-of-Fit, Pseudo R-Square and Test of Parallel Lines are fitted to the data sets to test the accuracy and correctness of the model. The results indicated that the overall prevalence of hypertension rate is high at 36.4%, among the adult population, body mass index and gender are statistically significant, and Age is not significant in the study. Individuals that are overweight are more likely to be hypertensive compare to other weights. At age 40 – 49 years which have the highest rate of 26.5% and the odd ratio is 0.75 compared to others. One year increase in age 30 – 39, the cumulative odd of being hypertensive is 0.91 while other independent variables are held constant. The odd ratio of female being hypertensive is 0.85, therefore the females are more likely to be hypertensive with 54.4% compared to the males at 45.6% . There is no presence of multicolinearity among the variables and Logit models were formulated to calculate probabilities of the various possible outcomes.

Aeroponics is a relatively new soilless culture technology, which may produce food in space limited cities or non-arable land with high water use efficiency. The shoot and root growth, root characteristics, mineral contents of two lettuce cultivars were measured in aeroponics, as compared with hydroponics and substrate culture. The results showed that aeroponics remarkably improved the root growth with a significant greater root biomass, root/shoot ratio, and several times higher total root length, root area and root volume. However, the greater root growth did not lead to a better shoot growth compared with hydroponics, due to the limited availability of nutrients and water. It can be concluded that aeroponics systems may be better for high value true root crops production. Further research is necessary to figure out the suitable pressure, droplet size, and misting interval in order to improve the continuously availability of nutrients and water in aeroponics, if it is used to grow crops like lettuce for harvesting above-ground parts.

The shoulder region has the highest incidence of acute injuries in the sport of surfing. Little is known about the strength profile at the shoulder in a surfing cohort. The primary aim of this study was to establish the reliability of a rotator cuff strength testing procedure for surfers with a secondary aim of providing a profile of internal (IR) and external rotation (ER) strength in a competitive surfing cohort. Shoulder IR and ER isometric strength was measured using a hand-held dynamometer in 13 competitive surfers. Intra-class coefficient values ranged from 0.97 to 0.98 for intra rater reliability and were lower for inter rater reliability ranging from 0.80 to 0.91. Normalised force (N/Kg) for IR strength was significantly greater than ER strength bilaterally (dominant, p= 0.007, non-dominant, p<0.001). No significant differences (p< 0.79) were found in IR strength (N/Kg) between the dominant and non-dominant arms. ER strength (N/Kg) was significantly weaker on the non-dominant arm compared with the dominant arm (p<0.02). The non-dominant arm ER to IR ratio (0.82 ± 0.15) was significantly (p=0.025) lower than the dominant (0.88 ± 0.14) The current procedure is reliable with the same clinician, results indicate musculature asymmetry specific to the external rotators.

Control of nutrients, mainly nitrogen (N) and phosphorus (P), plays a significant role in preventing cyanobacterial blooms (harmful algal blooms (HABs)). This study aimed at evaluating changes in the risk of the occurrence of cyanobacterial blooms and advancing the understanding of how N and P affect the growth of cyanobacteria in a eutrophic lake, Lake Vombsjön, in southern Sweden. Statistical analysis was used to demonstrate the pattern of cyanobacterial blooms, that the highest content present in September and the later that algal blooms occur, the more likely it is a cyanobacterial bloom as cyanobacteria became dominating in October and November (90%). Two hypothesises tested in Lake Vombsjön confirmed namely that a high total phosphorus (TP) level correlates with an abundance of cyanobacteria and that low N:P ratio (total nitrogen/total phosphorus < 20) favours the growth of cyanobacteria. To control the growth of cyanobacteria in Lake Vombsjön, the TP level should be kept below 20 µg/L and the N:P ratio be maintained at a level of over 20. The two species Planktothrix agardhii, and Pseudanabaena spp. should be carefully monitored especially in late autumn. Future work should consider any high degree of leakage from the sediment of the dissolved phosphorus available there.

Categorical data analysis of 2 x 2 contingency tables is extremely common, not least because they provide odds and risk ratio statistics in medical research. The χ2 test is most often used, although some researchers use the likelihood ratio test (LRT). Does it matter which test is used? This paper argues that the LRT rather than the χ2 test should be used when we are interested in testing whether two variables are independent, as is typically the case. In contrast, the χ2 test should be reserved for where the data appear to match too closely a particular hypothesis (e.g. the null hypothesis), as may occur in the investigation of data integrity. Finally, it is argued that the evidential approach provides a consistent and coherent way in which tests can be made for each of these situations.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

The golden ratio, also known as Phi (ϕ ≈ 1.618034), attracted the interest of mathematicians, artists, and intellectuals for many centuries, probably from when it was discovered in human anthropometry. Even in recent times, researchers found the presence of golden ratio in Renaissance paintings and aesthetic preferences. The reasons behind the fascination with the golden ratio remain unclear, but it has been suggested that stimuli containing this proportion are often perceived as beautiful. However, evidence is conflicting, and the literature struggles to establish the existence of individual preferences for golden ratio. To gain new insights into the nature of these preferences, one hundred participants completed an implicit association task, with either golden ratio or random stimuli presented with positive or negative words. Participants initially categorized the stimuli based on their assigned categories. Then, we assessed their explicit preferences by asking to rate the stimuli in terms of pleasantness and by completing a line bisection task and the Ultimate Game. The results revealed the typical effects observed in implicit association tasks, with improved response times and accuracy when golden ratio stimuli were associated with positive word categories. In contrast, explicit ratings yielded mixed results. We discuss our findings in relation to previous studies that have explored this issue, highlighting the ongoing debate surrounding preferences for the golden ratio.

Recent technological advances have significantly increased the data volume obtained from deep space exploration missions, making the downlink rate a primary limiting factor. Particularly, JAXA’s Martian Moons eXploration (MMX) mission encounters this problem when identifying safe and scientifically valuable landing sites on Phobos using high-resolution images. A strategic approach in which we effectively reduce image data volumes without compromising essential scientific information is thus required. In this work, we investigate the influence of image data compression, especially as it concerns the accuracy of generating the local Digital Terrain Models (DTMs) that will be used to determine MMX’s landing sites. We obtain simulated images of Phobos that are compressed using the CCSDS-120 with integer/float-point discrete wavelet transform (DWT), candidate algorithms for the MMX mission. Accordingly, we show that, if the compression ratio is 70% or lower, the effect of image compression remains constrained, and local DTMs can be generated within altitude errors of 40 cm on the surface of Phobos, which is ideal for selecting safe landing spots. We conclude that the compression ratio can be increased as high as 70%, and such compression enables us to facilitate critical phases in the MMX mission even with the limited downlink rate.

Background: The proportion of dietary protein may play a key role in the development of obesity in children and adolescents. Methods: Cross-sectional data of 4,336 children and adolescents from the National Health and Nutrition Survey (NHANES) during 2011 to March 2020 were analyzed. Multivariate logistic regression analysis was used to estimate odds ratios (OR) and 95% confidence intervals, and restriction cubic spline was uesd to explore nonlinear relationships of dietary protein energy supply ratio and obesity in children and adolescents. Results:In the adjusted logistic regression model, for every 1% increase in dietary protein energy ratio in children and adolescents, the increased risk of obesity was 4% (OR=1.04,95%CI:1.01-1.08). The restrictive cubic spline showed a nonlinear relationship between dietary protein energy ratio and obesity in children aged 6-11 years (P <0.05). The dietary protein energy supply ratio was included in the logistic regression model after converting to quartiles into categorical variables. The adjusted OR of children aged 6-11 years was 2.08 (95%CI:1.34, 3.23,P <0.01) for the highest quartile of dietary protein energy supply ratio compared with the lowest quartile. Conclusion: In American children, dietary protein energy supply ratios was positively correlated with obesity, independent of individual characteristics and energy.

The recently discovered Gaia BH1 binary system, a Sun-like star and a dark object (presumably a black hole), may significantly change our understanding of the population of low-q binaries. The paper presents the components mass ratio distributions of binary systems of different observational classes. They all demonstrate a significant shortage of low-q systems. It is shown that this shortage can be filled with the help of search and study of objects like Gaia BH1.

Prosthetics have come a long way since their inception, and recent advancements in materials science have enabled the development of prosthetic devices with improved functionality and comfort. One promising area of research is the use of auxetic metamaterials in prosthetics. Auxetic materials have a negative Poisson's ratio, which means that they expand laterally when stretched, unlike conventional materials, which contract laterally. This unique property allows for the creation of prosthetic devices that can better conform to the contours of the human body and provide a more natural feel. In this review article, we provide an overview of the current state of the art in the development of prosthetics using auxetic metamaterials. We discuss the mechanical properties of these materials, including their negative Poisson's ratio and other properties that make them suitable for use in prosthetic devices. We also explore the limitations that currently exist in implementing these materials in prosthetic devices, including challenges in manufacturing and cost. Despite these challenges, the future prospects for the development of prosthetic devices using auxetic metamaterials are promising. Continued research and development in this field could lead to the creation of more comfortable, functional, and natural-feeling prosthetic devices. Overall, the use of auxetic metamaterials in prosthetics represents a promising area of research with the potential to improve the lives of millions of people around the world who rely on prosthetic devices.

With covid infection having a periodic occurrence and each wave affecting millions of people, there is an urgent need for healthcare providers to develop readily available biological markers to predict the severity and mortality of COVID-19 infection at an early stage of the disease to predict the most optimal management. The Neutrophil – lymphocyte Ratio (NLR) and Platelet-lymphocyte ratio (PLR), are novel inflammatory markers suggested to predict the severity of illness in COVID -19 patients. We evaluated a retrospective cohort of 224 patients with covid 19 illnesses from August 2020 to October 2020. We categorized the patients into 'mild' and 'moderate to severe as per the severity of their illnesses. The optimal cut-off values of the continuous NLR, PLR, and Age were calculated by applying the receiver operating characteristic (ROC) curve analysis. Sensitivity, specificity, and likelihood ratios were calculated from ROC analysis. The results showed that Age, Hb, and NLR are significant predictors of the severity of illness. So we quantified the predictive contribution of those variables by its Z- score and showed that NLR is the strongest predictor followed by Age.ROC curve analysis revealed NLR to be an excellent predictor of disease severity (sensitivity 88.30% and specificity 82.60%) at a cut-off of > 4.24. A cut-off of 165.63 was obtained for PLR, which showed good predictive value for the severity of illness. A NLR > 6 was used as a predictor for mortality due to covid illness with good sensitivity and specificity. Conclusion: NLR and PLR can be used as prognostic markers to identify the severity of covid illness and the probability of mortality in the future in low-resource settings. Given its low cost, easily available, accessible, and reproducible data, it can be used as a useful marker to assist the physician in early referral and treatment of covid 19 infected patients.

Background: The Sequential Organ Failure Assessment (SOFA) is a scoring system used for the evaluation of disease severity and prognosis of critically ill patients. The impedance ratio (Imp-R) is a novel mortality predictor. Aims: This study aimed to evaluate the combination of SOFA + Imp-R in the prediction of mortality in critically ill patients admitted to the emergency department (ED). Methods: A retrospective cohort study was performed in adult patients with acute illness admitted to the ED of a tertiary-care referral center. Baseline SOFA score and bioelectrical impedance analysis to obtain the Imp-R were performed within the first 24 hours after admission to the ED. A Cox regression analysis was performed to evaluate mortality risk of initial SOFA score plus Imp-R. Harrell's C-statistic and decision curve analyses (DCA) were performed. Results: Out of 325 patients, 240 were included for analysis. Overall mortality was 31.3%. Only 21.3% of non-surviving patients died after hospital discharge, and 78.4% died during hospital stay. Of the latter, 40.6% died in the ED. SOFA and Imp-R values were higher in non-survivors and were significantly associated with mortality in all models. The combination of SOFA + Imp-R significantly predicted 30-day mortality, in-hospital mortality, and ED mortality with area under the curve (AUC) of 0.80 (95% CI: 74-0.86), 0.79 (95% CI: 0.74-0.86) and 0.75 (95% CI: 0.66-0.84) respectively. The DCA showed that combining SOFA + Imp-R improved the prediction of mortality through the lower risk thresholds. Conclusion: The addition of Imp-R to baseline SOFA score at admission to the ED improves mortality prediction in severely acutely ill patients admitted to the ED.

Pulmonary embolism (PE) is one of the leading causes of cardiovascular mortality, therefore new parameters regarding risk stratification are sought after. In patients admitted for acute PE we investigated associations between the initial coagulation impairment, expressed by prothrombin time international normalised ratio (INR), and parameters reflecting PE severity. Furthermore, in-hospital, 30-day and long-term mortality were also evaluated. The analysis included 848 patients who were divided into two groups: with normal INR≤1.2, and elevated INR>1.2 (252 patients, 29.7%). The group with elevated INR presented higher incidence of tachycardia and lower systolic blood pressure, higher CRP, d-dimer, and NT-proBNP. This group presented higher estimated systolic pulmonary artery pressure (49 IQR39-62mmHg vs 43 IQR32-53mmHg, p<0.001) and shorter pulmonary artery acceleration time (65 IQR55-85ms vs 81 IQR63-102ms; p<0.001). Patients with elevated INR had more often a sPESI of 1 or higher (78%vs60%, p=0.003). Cox regression model revealed that age, leukocyte level, SBP, neoplasm, and INR are associated with higher risk of death (p<0.001). Finally, elevated INR was associated with higher in-hospital (13%vs3%; p<0.001), 30-day (19%vs6%; p<0.001), and long-term mortality (p<0.001). Summing up, elevated INR on admission is frequent in patients with PE, reflects worse clinical condition and is related to PE severity and prognosis.

Whether resurfacing or not resurfacing the patella during total knee arthroplasty (TKA) still is a challenge to orthopedic surgeons. A significant reason for this controversy is the far from perfect outcomes of both techniques, resulting from inadequate knowledge of normal patellar dimensions in a diseased one. The primary purpose of the current study is to find the pre-diseased patellar dimensions and the ethnic differences in patellar dimensions. We measured the patella's dimensions on 927 normal young adult knee MRIs from seven different ethnicities. Besides comparing the dimensions between sexes, ages, and sides, we analyzed the differences among ethnic groups. The average thickness was 25.12±2.33 mm; the average width was 44.57±4.32 mm, the average articular surface length was 32.69±3.75 mm, with significant gender, age, and ethnic differences. There were also significant differences in dimensions among ethnic groups, except for between the Indians and Far Eastern Asians and between the Arabs and North Africans. We could also find a robust mathematical relationship between the patella's width, length, and thickness. The ethnic differences in patellar dimensions found in this study can help optimize surgical technique and implant designs for patellar resurfacing. The mathematical equation will help the surgeons find the normal, pre-diseased patella thickness to prevent over-or under-stuffing during the patellar resurfacing.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

Background: The COVID-19 transmission has been established to occur through respiratory droplets from coughing and sneezing. Health agencies have strongly recommended the use of facemask as a precaution from cross-transmission. Objective: This study investigated the prevalence of facemask use among visitors to the hospital. This study also investigated the demographic factors contributing to unacceptable facemask practice. Setting: This prospective observational study was done among hospital visitors to a district specialist hospital during COVID-19 pandemic outbreak. Methods: Individuals entering through dedicated entry point were observed for the type, category and practice of wearing personal protective equipment. Inclusion criteria for this study were any individual's ≥ 2 years old entering the treatment facility from selected entry points. Patients were categorized into two groups of acceptable and unacceptable facemask practice. The Pearson chi-square was used to test for differences in investigated variables in the univariate setting and Binary Logistic regression model was used in the multivariate setting. Main Outcome Measure: Prevalence, acceptance practice and odds ratio of unacceptance of facemask use. Results: Among 1652 individuals included in the final analysis, 1574 (96.9%) was observed wearing facemask with 1269 (72.0%) of individuals worn medical-grade facemask. However, among them, only 1397 (88.8%) individuals' facemask practice was acceptable while the reaming 177 (11.2) individuals were perceived with unacceptable facemask practice. Male individuals, Malay ethnic and high risk age group are 1.47 times (Odds Ratio: OR=1.47; 95% CI, 1.06-2.06; p=.023), 2.18 times (OR=2.18; 95% CI, 1.55-3.08; p<.001) and 1.99 times (OR=2.18; 95% CI, 1.42 - 2.77; p<.001) more likely to exhibit unacceptable facemask practice respectively. Conclusion: Extensive use of facemasks coupled with environmental hygiene measures is a public health strategy which can help to mitigate the COVID-19 epidemic impact. However, a targeted comprehensive strategy to improve compliance to proper facemask practice among the high-risk population is needed to achieve maximal protective benefit.

Honeycomb-like CO₃O₄ nanosheets with high specific surface area were successfully synthesized on porous nickel foam by the facile hydrothermal method followed by an annealing treatment (300 °C), which were used as high-performance supercapacitor electrodes. The effects of mole ratio of hexamethylenetetramine (HMT) and Co(NO₃)₂ (1:1, 2:1, 3:1, 4:1, 5:1 and 6:1）as the reactants on morphological evolution and electrochemical performance of the electrodes were investigated in detail. X-ray diffractometry, transmission electron microscopy, X-ray photoelectron spectroscopy and scanning electron microscopy were applied to characterize the structure and morphology of the products. The electrochemical performance was measured by cyclic voltammetry (CV) and galvanostatic charge/discharge. The results indicated that phase constituents were almost unaffected with the change in mole ratio of HMT and Co(NO₃)₂. However, the significant morphological evolution of Co₃O₄ was observed with increasing the mole ratio, which was described as followed: the nanosheets accompanied with a large number of spherical nanoparticles→the formation of some strip-like particles due to the agglomeration of spherical nanoparticles→the formation of new nanosheets resulting from the growth of strip-like particles→the formation of coarse flower-like particles owing to the connection among the nanosheets→the nanosheets gradually covered with flower-like particles. Accompanied with the change, the specific surface area was increased firstly, and then decreased. A maximum was obtained in the HMT and Co(NO₃)₂ mole ratio of 4:1, which was further validated by CV and galvanostatic charge/discharge tests. The specific capacitance value was 743.00 F·g^-1 at 1 A·g^-1 in the galvanostatic charge/discharge test, which was apparently higher than those in the other mole ratios (139.11 F·g^-1 in 1:1, 280.46 F·g^-1 in 2:1, 503.29 F·g^-1 in 3:1, 463.75 F·g^-1 in 5:1 and 363.74 F·g^-1 in 6:1). The change was also observed in the CV test with a scanning rate of 5 mV·s^-1 (121.32 F·g^-1 in 1:1, 217.33 F·g^-1 in 2:1, 559.86 F·g^-1 in 3:1, 693.56 F·g^-1 in 4:1, 423.35 F·g^-1 in 5:1 and 321.64 F·g^-1 in 6:1). Co₃O₄ synthesized in the mole ratio of 4:1 also demonstrated an excellent cyclic performance, in which about 97% of the initial specific capacitance was remained at 1 A·g^-1 for 500 cycles in the galvanostatic charge/discharge test. This excellent electrochemical performance was ascribed to high specific surface area of Co₃O₄ nanosheets that provide enough channels and space for ions transportion.

Good data analysis is required for the optimal design of water resources projects. However, data are not regularly collected due to material or technical reasons, which results in incomplete-data problems. Available data and data length are of great importance to solve those problems. Various studies have been conducted on missing data treatment. This study used data from the flow observation stations on Yeşilırmak River in Turkey. In the first part of the study, models were generated and compared in order to complete missing data using ANFIS, multiple regression and Normal Ratio Method. In the second part of the study, the minimum number of data required for ANFIS models was determined using the optimum ANFIS model. Of all methods compared in this study, ANFIS models yielded the most accurate results. A 10-year training set was also found to be sufficient as a data set.

Background: Strong indicators of inflammation, such as C-reactive protein (CRP), hypersensitive CRP (hs-CRP), and a series of hematological indices, including platelet to lymphocyte ratio (PLR), neutrophil to lymphocyte ratio (NLR), hematocrit (HCT) and red blood cell distribution width (RDW), are regarded related with the incidence of contrast induced nephropathy (CIN) closely. Whereas, it remains unclear whether they can function as predictors of CIN onset. The objective of this meta-analysis was to determine the relationship between above indicators and CIN incidence among patients receiving coronary intervention. Methods: Clinical studies were retrieved from the electronic databases of PubMed, EMBASE, Google Scholar, Clinical Trials, and science direct from their inception to June 3rd, 2020. Meta-analysis was performed on pool eligible studies. Two reviewers screened all titles and abstracts and independently assessed all articles. Results: A total of 26 studies involving 29,454 patients were included in the meta-analysis. Pooled analysis results revealed that patients with higher CRP (odds ratio [OR]=1.06, 95% confidence interval [CI]: 1.01–1.12, P=0.02), hs-CRP (OR=1.03, 95% CI: 1.01–1.06, P=0.004), NLR (OR=1.11, 95% CI: 1.01–1.20, P=0.02), RDW (OR=1.35, 95% CI: 1.19–1.53, P<0.00001), and lower HCT (OR=0.94, 95% CI: 0.92–0.97, P=0.0003) all exhibited significantly higher CIN rates, but there was no significant association between PLR and CIN risk (OR=1.12, 95% CI: 0.99–1.26, P=0.07). Conclusion: The meta-analysis reported here demonstrates that pre-angiography CRP/hs-CRP and some hematological indices are associated with CIN.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

Mycobacterium tuberculosis (Mtb) is the etiological agent of tuberculosis (TB), a disease that alt-hough preventable and curable, remains a global epidemic due to the emergence of resistance and a latent form responsible for a long period of treatment. Drug discovery in TB is a challenging task due to the heterogeneity of the disease, the emergence of resistance and an uncomplete knowledge of the pathophysiology of the disease. The limited permeability of the cell wall and the presence of multiple efflux pumps remain a major barrier to achieve effective intracellular drug accumulation. While the complete genome sequence of Mtb has been determined and several potential protein targets have been validated, the lack of adequate models for in vitro and in vivo studies is a limit-ing factor in TB drug discovery programs. In current therapeutic regimens, less than 0.5% of bac-terial proteins are targeted being the biosynthesis of the cell wall and the energetic metabolism two of the most important processes exploited for TB chemotherapeutics. This review provides an overview on the current challenges in TB drug discovery and emerging Mtb druggable proteins, and how chemical probes for protein profiling enabled the identification of new targets and bi-omarkers, paving the way to disruptive therapeutic regimens and diagnostic tools.

Lake Rawapening, Semarang Regency, Indonesia, has incorporated a holistic plan in its management practices. However, despite successful target achievements, some limitations remain that a review of its management plan is needed. This paper identifies and analyzes existing lake management strategies as a standard specifically in Lake Rawapening by exploring various literature, both legal frameworks and scholarly articles indexed in Google Scholar and published in Water by MDPI about lake management in many countries. There are two major types of lake management, namely pillar-based and object-based. While the former is the foundation of a conceptual paradigm that does not comprehensively consider the roles of finance and technology in the lake management, the latter indicates the objects to manage so as to create standards or benchmarks for the implementation of various programs. Overall, Lake Rawapening management should include more programs on erosion-sedimentation control and monitoring of operational performance using information systems.

Nature-based solutions (NbS) are increasingly recognised for their potential to address both the climate and biodiversity crises. These outcomes are interdependent, and both rely on the capacity of NbS to support and enhance the health of an ecosystem: its biodiversity, the condition of its abiotic and biotic elements, and its capacity to function normally despite environmental change. However, while understanding of ecosystem health outcomes of nature-based interventions for climate change mitigation is growing, the outcomes of those implemented for adaptation remain poorly understood with evidence scattered across multiple disciplines. To address this, we conducted a systematic review of the outcomes of 109 nature-based interventions for climate change adaptation using 33 indicators of ecosystem health across eight broad categories (e.g. diversity, biomass, ecosystem functioning and population dynamics). We showed that 88% of interventions with positive outcomes for climate change adaptation also reported measurable benefits for ecosystem health. We also showed that interventions were associated with a 67% average increase in local species richness. All eight studies that reported benefits in terms of both climate change mitigation and adaptation also supported ecosystem health, leading to a triple win. However, there were also trade-offs, mainly for forest management and creation of novel ecosystems such as monoculture plantations of non-native species. Our review highlights two major limitations of research to date. First, only a limited selection of metrics are used to assess ecosystem health and these rarely include key aspects such as functional diversity and habitat connectivity. Second, taxonomic coverage is poor: 67% of outcomes assessed only plants and 57% did not distinguish between native and non-native species. Future research addressing these issues will allow the design and adaptive management of NbS to support healthy and resilient ecosystems, and thereby enhance their effectiveness for meeting both climate and biodiversity targets.

In our study, we investigated the prognostic significance of hematological markers—NLR (Neutrophil-to-Lymphocyte Ratio), PLR (Platelet-to-Lymphocyte Ratio), and RDW-CV (Red Blood Cell Distribution Width - Coefficient of Variation)—in 117 glioblastoma patients. Data collected from January 2016 to December 2018 included demographics, clinical scores, and treatment regimens. Unlike previous research, which often examined these markers solely before surgery, our unique approach analyzed them at multiple stages: preoperative, postoperative, and before adjuvant therapies. We correlated these markers with overall survival (OS) and progression-free survival (PFS) using statistical tools, including ANOVA, Cox regression, and Kaplan-Meier survival analyses, employing SPSS version 29.0. Our findings revealed notable variations in NLR, PLR, and RDW-CV across different treatment stages. NLR and PLR decreased after surgery, with some stabilization post-STUPP phase (NLR: p=0.007, η2p=0.06; PLR: p=0.001, η2p=0.23), while RDW-CV increased post-surgery and during subsequent treatments (RDW-CV: p &lt; 0.001, η2p=0.67). Importantly, we observed significant differences between the preoperative phase and other treatment phases. Additionally, higher NLR and RDW-CV at the second-line treatment and disease progression were associated with an increased risk of death (NLR at 2nd line: HR=1.03, p=0.029; RDW-CV at progression: HR=1.14, p=0.004). We proposed specific marker cutoffs that demonstrated significant associations with survival outcomes when applied to Kaplan-Meier survival curves (NLR at 2nd line &lt; 5: p&lt;0.017; RDW-CV at progression &lt; 15: p=0.007). Elevated NLR and RDW-CV at later treatment stages correlated with poorer OS and PFS. No significant preoperative differences were detected. These biomarkers may serve as non-invasive tools for glioblastoma management.

Due to their increased surface area, extent of swelling and active substance loading capacity and flexibility, nanogels made from natural and synthetic polymers have gained significant interest in the scientific and industrial areas. Especially, customized design and implementation of non-toxic, biocompatible, and biodegradable micro/nano carriers makes their usage very feasible for a range of biomedical applications, including drug delivery, tissue engineering, and bioimaging. The design and application methodologies of nanogels have been outlined in this review. Additionally, the most recent advancements in nanogel biomedical applications have been discussed, with a particular emphasis on applications for the delivery of drugs and biomolecules.

Vision-based tactile sensors (VBTS) have become the de facto method of giving robots the ability to obtain tactile feedback from their environment. Unlike other solutions to tactile sensing, VBTS offers high spatial resolution feedback without compromising on instrumentation costs or incurring additional maintenance expenses. However, conventional cameras used in VBTS have a fixed update rate and output redundant data, leading to computational overhead downstream. In this work, we present a neuromorphic vision-based tactile sensor (N-VBTS) that employs observations from an event-based camera for contact angle prediction. Particularly, we design and develop a novel graph neural network, dubbed TactiGraph, that asynchronously operates on graphs constructed from raw N-VBTS streams exploiting their spatiotemporal correlations to perform predictions. Although conventional VBTS uses an internal illumination source, TactiGraph is reported to perform efficiently in both scenarios, with and without an internal illumination source. Rigorous experimental results revealed that TactiGraph achieved a mean absolute error of 0.62∘ in predicting the contact angle and was faster and more efficient than both conventional VBTS and other N-VBTS, with lower instrumentation costs. Specifically, N-VBTS requires only 5.5% of the compute-time needed by VBTS when both are tested on the same scenario.

For disciplines like biological science, security, and the medical field, link prediction is a popular research area. To demonstrate the link prediction many methods have been proposed. Some of them that have been demonstrated through this review paper are TransE, Complex, DistMult, and DensE models. Each model defines link prediction with different perceptions. We argue that the practical performance potential of these methods, having similar parameter values, using the fine-tuning technique to evaluate their reliability and reproducibility of results. We describe those methods and experiments; provide theoretical proofs and experimental examples, demonstrating how current link prediction methods work in such settings. We use the standard evaluation metrics for testing the model's ability.

Zoos are increasingly putting in place formalized animal welfare assessment programs to allow monitoring of welfare over time, as well as to aid in resource prioritization. These programs tend to rely on assessment tools that incorporate resource-based and observational animal- focused measures since it is rarely feasible to obtain measures of physiology in zoo-housed animals. A range of assessment tools are available which commonly have a basis in the Five Domains framework. A comprehensive review of the literature was conducted to bring together recent studies examining welfare assessment methods in zoo animals. A summary of these methods is provided with advantages and limitations of the approach es presented. We then highlight practical considerations with respect to implementation of these tools into practice, for example scoring schemes, weighting of criteria, and innate animal factors for consideration. It is concluded that would be value in standardizing guidelines for development of welfare assessment tools since zoo accreditation bodies rarely prescribe these. There is also a need to develop taxon or species- specific assessment tools to inform welfare management.

In mesoscale eddies, chemical properties and biological composition are different from those in surrounding water, due to their unique physical processes. It is unclear how physical-biological coupling occurs in warm-core eddies, particularly since no study has examined the relationship between bacteria and viruses. The purpose of the present study was to examine the influence of anticyclonic warm eddy on the relationship between bacterial and viral abundances as well as viral activity (viral production) in different depths. In the core of warm eddy, bacterial abundance (0.48 to 2.82 ×105 cells mL−1) fluctuated less than that of the outside eddy (1.12 to 7.03×105 cells mL−1). In particular, there was four-folds higher of viral-bacterial abundance ratio (VBR) estimated within the eddy below DCM than the outside eddy. We suggest that prevailing physical forces with downwelling at the center of the anticyclonic warm eddy, viruses can also be transmitted into the deep ocean directly through adsorption on particulate organic matter during sinking. Overall, our findings provide valuable insights into the interaction between bacterial and viral communities and their ecological mechanism within the warm eddy.

Background This study aimed to determine the association between immune checkpoint inhibitors (ICIs) and the risk of herpes zoster (HZ) incidence in patients with lung cancer. Method We obtained national claims data of 51,021 patients from South Korea with lung cancer between August 2017 and December 2021. The study population was classified into ICIs and non-ICIs groups based on prescription of ICIs at least once during the study period. To estimate the effects of ICIs treatment compared with those without ICIs treatment on HZ incidence, we used the Cox proportional hazards model adjusted for sex, age, comorbidities, and concomitant use of immunosuppressive drugs. Stratified analyses based on sex, age, and comorbidities were conducted to identify corresponding risk factors. Results Of the 51,021 study participants, 897 (1.8%) were prescribed ICIs, and 2,262 (4.4%) were diagnosed with HZ. Approximately 75.6% of the patients were male, and the prevalence of diabetes, cardiovascular disease, and chronic lung disease in the ICIs group was significantly lower than that in the non-ICIs group. The Kaplan–Meier plot showed that the probability of incidence of HZ in the ICIs group was lower than that in the non-ICIs group. Additionally, treatment with ICIs was associated with a 31% lower risk of developing HZ when compared to that seen without ICIs treatment (95% confidence interval [CI], 0.48–1.00). This association was stronger in females (hazard ratio [HR], 0.42; 95% CI, 0.19–0.94) and those less than 68 years of age (HR, 0.58; 95% CI, 0.34–0.99). Conclusion In these real-world data from an Asian population with lung cancer, ICIs treatment might be associated with a reduced risk of HZ compared to that without ICIs treatment.

The ratio between blade height and chord, named aspect ratio (AR), plays an important role in compressor aerodynamic design. Once selected, it influences stage performance, blade losses, and the stage stability margin. The choice of the design AR involves both aerodynamic and mechanical considerations, and a reasonable aim is frequently to achieve a desired operating range while maximizing efficiency. For a fixed set of aerodynamic and geometric parameters there will be an optimal choice in AR that achieves a maximum efficiency. However, for a state-of-the-art aero-engine design optimality means multi-objective optimality, that is reaching the highest possible efficiency for a number of operating points while achieving a sufficient stability margin. To this end, the influence of the AR on the performance of the first rotor row of a multistage multi-objective high-speed compressor design is analyzed. A careful setup of the high-speed aerodynamic design problem allows the effect of the AR to be isolated. Close to the optimal AR, only a modest efficiency variation is observed, but a considerable change in compressor stability margin (SM) is noted. Decreasing the AR allows for an increasing efficiency, but at the expense of a reduced surge margin. This allows the designer to trade efficiency for stability. Increasing the AR, however, is shown to reduce both surge margin and efficiency, hence a distinct optimality in stability is observed for the analyzed rotor blade row. In this work, the optimality in surge margin with respect to AR is observed whereas a close to optimal efficiency. The predicted range from AR=1.10 to AR=1.64, is only indicative, considering that the definition of a multi-objective optimality requires balancing efficiency and surge margin and that the choice of balancing these two criteria requires making a design choice along a pareto optimal front.

: Inflammation may mediate the association of mitral valve prolapse (MVP) with ventricular scarring and arrhythmia. The purpose of this study is to investigate the association of neutrophil- and platelet-to-lymphocyte ratios (NLR, PLR) with ventricular arrhythmia in MVP. Clinical and demographic data were extracted from electronic medical records for all patients aged 18-90 years with MVP on echocardiography between 2016-19 at our institution. We studied 65 patients who had a differential blood count within six months prior to ambulatory ECG (A- ECG) (medi-an age [IQR] 70 [61-77] years; 62% female; 12% African American). Patients with surgery or in-fection within six months prior to CBC were excluded. Complex or frequent ventricular ectopy (cfVE) was defined as the presence of two or more premature ventricular contractions (PVCs) on a 10-second ECG tracing or greater than 1% PVC burden or NSVT on ambulatory ECG monitoring. Logistic and bivariate regression was used to analyze clinical, electrocardiographic and echo-cardiographic factors associated with NLR and PLR. Factors associated with higher NLR were congestive heart failure (p=0.005), male sex (p=0.01), age (p=0.003), and bileaflet MVP (p=0.04). NLR was associated with higher absolute PVC burden (rs=0.28, p=0.03) and cfVE (median NLR [IQR] 3.0 [1.6 – 6.3]) with cfVE versus (2.4 [1.4-3.4], p=0.04) without cfVE. An NLR of 5.6 yielded 50% sensitivity and 90% specificity for PVC burden >1% (AUC 0.69). No significant association was found between PLR and PVC burden or cfVE. NLR is associated with PVC burden and com-plex ventricular ectopy in MVP, suggesting that inflammation is a significant factor in the patho-genesis of ventricular arrhythmia in this condition.