Ultrafast pump-probe spectroscopic studies allow for deep insights into the mechanisms and timescales of photophysical and photochemical processes. Extracting valuable information from these studies, such as reactive intermediates' lifetimes and coherent oscillation frequencies, is an example of the inverse problems of chemical kinetics. This article describes a consistent approach for solving this inverse problem that avoids the common obstacles of simple least-squares fitting that can lead to unreliable results. The presented approach is based on the regularized Markov Chain Monte Carlo sampling for the strongly nonlinear parameters, allowing for a straightforward solution of the ill-posed nonlinear inverse problem. The software to implement the described fitting routine is introduced and the numerical examples of its application are given. We will also touch on critical experimental parameters, such as the temporal overlap of pulses and cross-correlation time and their connection to the minimal reachable time resolution.

Broadband reverse saturable absorption is systematically investigated via Z-scan, transient absorption spectrum (TAS). The excited state absorption and negative refraction of Orange IV are observed in the Z-scan experiment at 532 nm. Meanwhile, two-photon induced excited-state absorption and pure two-photon absorption are observed at 600 nm and 700 nm with the pulse width of 190 fs, respectively. An ultrafast broadband absorption in visible wavelength region is observed via TAS. The different nonlinear absorption mechanism at multiple wavelengths is discussed and interpreted from the results of TAS. In addition, the ultrafast dynamics of negative refraction in the excited state of Orange IV is investigated via degenerate phase object pump probe, from which the weak long-lived excited state is extracted. All studies indicate that Orange IV has the potential to be further optimized into a superior broadband reverse saturable absorption material and also has certain reference significance for the study of optical nonlinearity in organic molecules containing azobenzene groups.

Amorphous chalcogenide (ChGs) glasses are intrinsically metastable, highly photosensitive, and therefore exhibit numerous lightinduced effects upon bandgap and sub-bandgap illumination. Depending on the pulse duration of the excitation laser, ChGs exhibit a series of lightinduced effects spanning over femtosecond to seconds time domain. For continuous wave illumination, the effects are dominantly metastable in terms of photodarkening (PD) and photobleaching (PB) that takes place via homopolar to heteropolar bond conversion. On the other hand, under nanosecond and ultrafast pulsed illumination, ChGs exhibit transient absorption (TA) that is instigated from the transient bonding rearrangements through self-trapped exciton recombination. In the first part of the review, we pay special attention to continuous wave lightinduced PD and PB, while in the second part we will focus on the TA and controlling such effects via internal and external parameters e.g., chemical composition, temperature, sample history etc.

As one of the representatives of emerging metallic transition metal dichalcogenides, niobium ditelluride (NbTe₂) has attracted intensive interest recently due to its distorted lattice structure and unique physical properties. Here, we report on the ultrafast carrier dynamics in NbTe₂ measured using time-resolved pump-probe transient reflection spectroscopy. A thickness-dependent carrier relaxation time is observed, exhibiting a clear increase in the fast and slow carrier decay rates for thin NbTe₂ flakes. In addition, pump power dependent measurements indicate that the carrier relaxation rates are power-independent, with the peak amplitude of the transient reflectivity increasing linearly with pump power. Isotropic relaxation dynamics in NbTe₂ is also verified by performing polarization-resolved pump-probe measurements. These results provide an insight into the light-matter interactions and charge carrier dynamics in NbTe₂ and will pave the way for its applications to photonic and optoelectronic devices.

The aim of this work was to test polyamines as potential natural substrates of the Acinetobacter baumannii chlorhexidine efflux protein AceI using near-UV synchrotron radiation circular dichroism (SRCD) spectroscopy. The Gram-negative bacterium A. Baumannii is a leading cause of hospital-acquired infections and an important foodborne pathogen. A. Baumannii strains are becoming increasingly resistant to antimicrobial agents, including the synthetic antiseptic chlorhexidine. AceI was the founding member of the recently recognised PACE family of bacterial multidrug efflux proteins. Using the plasmid construct pTTQ18-aceI(His₆) containing the A. Baumannii aceI gene directly upstream from a His₆-tag coding sequence, expression of AceI(His₆) was amplified in E. coli BL21(DE3) cells. Near-UV (250-340 nm) SRCD measurements were performed on detergent-solubilised and purified AceI(His₆) at 20 °C. Sample and SRCD experimental conditions were identified that detected binding of the triamine spermidine to AceI(His₆). In a titration with spermidine (0-10 mM) this binding was saturable and fitting of the curve for the change in signal intensity produced an apparent binding affinity (K_D) of 3.97 +/- 0.45 mM. These SRCD results were the first experimental evidence obtained for polyamines as natural substrates of PACE proteins.

We put forward a co-axial pump(optical)-probe(X-rays) experimental concept and show performance of the optical component. A Bessel beam generator with a central 100 micrometers-diameter hole (on the optical axis) was fabricated using femtosecond (fs) laser structuring inside a silica plate. This flat-axicon optical element produces a needle-like axial intensity distribution which can be used for the optical pump pulse. The fs-X-ray free electron laser (X-FEL) beam of sub-1 micrometer diameter can be introduced through the central hole along the optical axis onto a target as a probe. Different realisations of optical pump are discussed. Such optical elements facilitate alignment of ultra-short fs-pulses in space and time and can be used in light-matter interaction experiments at extreme energy densities on the surface and in the volume of targets. Full advantage of ultra-short 10 fs X-FEL probe pulses with fs-pump(optical) opens an unexplored temporal dimension of phase transitions and the fastest laser-induced rates of material heating and quenching. A wider field of applications of fs-laser-enabled structuring of materials and design of specific optical elements for astrophotonics is presented.

Background: Air-pouch balloon-assisted probes have proven to be both simple and reliable tools for intracranial pressure (ICP) monitoring. However, we experienced reproducible falsely high ICP measurement when the ICP probe was inserted in the intracerebral hematoma cavity. Thus, the aim of the experimental and translational study was to analyze the influence of ICP probe placement with regard to measured ICP values. Methods: Two Spiegelberg 3PN-sensors were simultaneously inserted into a closed drain system and were connected to two separate ICP monitors thereby allowing for simultaneous ICP measurements. This closed system was also engineered to allow for pressure to be gradually increased in a controlled fashion. Once the pressure was verified using two identical ICP probes, one of the probes was coated with blood in an effort to replicate placement within an intraparenchymal hematoma. Pressures recorded using the coated probe and control probe were then recorded and compared across a range of 0-60 mmHg. In an effort to further the translational relevance of our results two ICP probes were inserted in a patient that presented with a large basal ganglia hemorrhage that met criteria for ICP monitoring. One probe was inserted into the hematoma and the other into brain parenchyma; ICP values were recorded from both probes and the results compared. Results: The experimental set-up demonstrated a reliable correlation between both control ICP probes. Interestingly, the ICP probe covered with clot displayed a significantly higher average ICP value when compared to the control probe between 0mmHg and 50mmHg (p<0.001); at 60mmHg there was no significant difference noted. Critically, this trend in discordance was even more pronounced in the clinical setting with the ICP probe placed within the hematoma cavity having reported significantly higher ICP values as compared to the probe within brain parenchyma. Conclusion: Our experimental study and clinical pilot highlight a potential pitfall in ICP measurement that may result secondary to probe placement within hematoma. Such aberrant results may lead to inappropriate interventions in an effort to falsely addresses falsely elevated ICPs.

We report on the application of time-resolved inline digital holography to study the nonlinear optical properties of quantum dots deposited onto the sample glass. Fresnel diffraction patterns of the probe pulse due to noncollinear degenerate phase modulation induced by the femtosecond pump pulse were extracted from the set of inline digital holograms and analyzed. Absolute values of the nonlinear refractive index of both sample glass substrate and the deposited layer of quantum dots were evaluated using the proposed technique. To characterize the inhomogeneous distribution of samples’ nonlinear optical properties we proposed to plot an optical nonlinearity map calculated as a local standard deviation of diffraction patterns intensity induced by noncollinear degenerate phase modulation.

pH value almost affects the function of cells and organisms in all aspects, so in biology, biochemical and many other research fields, it is necessary to apply simple, intuitive, sensitive, stable detection of pH and base characteristics inside and outside the cell. Therefore, many research groups have explored the design and application of pH probes based on surface enhanced Raman scattering（SERS）. In this review article, we discussed the basic theoretical background of explaining the working mechanism of pH SERS sensors, and also briefly described the significance of cell pH measurement, and simply classified and summarized the factors that affected the performance of pH SERS probes. Some applications of pH probes based on surface enhanced Raman scattering (SERS) in intracellular and extracellular pH imaging and the combination of other analytical detection techniques are described. And finally, the development prospect of this field is prospected.

Mitochondrial hypochlorite (ClO-) plays important and often contradictory roles in maintaining the redox balance of mitochondria. Abnormal ClO- levels can induce mitochondrial inactivation and further cause cell apoptosis. Herein. we have developed an anthracene carboxyimide-based fluorescent probe mito-ACS for imaging mitochondrial ClO- in living cells. This probe exhibits some distinctive features as excellent resistance to photobleaching, high selectivity and sensitivity, as well as good water solubility. Mito-ACS showed a noticeable fluorescence response toward ClO-with a fast response (within 6 s) and a low detection limit (23 nM). Moreover, the introduction of triphenylphosphonium makes the probe soluble in water and selectively localizes to mitochondria. Furthermore, mito-ACS was successfully applied to image mitochondria ClO- in living cells with low toxicity. Remarkably. the less used fluorophore anthracene carboxyimide exhibiting excellent photostability and desirable optical properties provides a promising application prospect in biological systems.

Long gone was the time when tumors were thought to be insular masses of cells, residing independently at specific sites in an organ. Now, researchers gradually realize that tumors interact with the extracellular matrix (ECM), blood vessels, connective tissues and immune cells in their environment, which is now known as the tumor microenvironment (TME). It is found that the interactions between tumors and their surrounding promote tumor growth, invasion and metastasis. The dynamics and diversity of TME cause the tumors to be heterogeneous and thus pose a challenge for cancer diagnosis, drug design and therapy. As TME is significant in enhancing tumor progression, it is vital to identify the different components in the TME. This review explores how different factors in the TME supply tumors with the required growth factors and signaling molecules to proliferate, invade and metastasis. We also examine the development of TME-targeted nanotheranostics over the recent years for cancer therapy, diagnosis and anticancer drug delivery system. This review further discusses the limitations and future perspective of nanoparticle based theranostics when used in combination with current imaging modalities like Optical Imaging, Magnetic Resonance Imaging (MRI) and Nuclear Imaging (PET and SPECT).

Pump Sizing is the process of dimensional matching an impeller and stator to provide a satisfactory performance test result and good service life during the operation of progressive cavity pumps. In this process, historical data analysis and dimensional monitoring are done manually, consuming a large amount of man-hours and requiring a deep knowledge of progressive cavity pump behavior. This work presents the use of complex networks in the construction of a prototype to recommend interference during the Pump Sizing process in a Progressive Cavity Pump. For this, data from different expert applications were used in addition to individual control Excel spreadsheets to build the database used in the prototype. From the pre-processed data, complex network techniques and the Betweenness Centrality metric were used to calculate the degree of importance of each order confirmation, as well as to calculate the dimensionality of the rotors. The model was evaluated using the mean squared error (MSE), obtaining a MSE of 0.28 for the cases where there were recommendations for order confirmations. Based on the results obtained, it was realized that there is a similarity with the dimensional defined by design engineers during the Pump Sizing process.

This study aims to explore the applicability of an innovative cervical tactile ultrasound approach for predicting spontaneous preterm birth (sPTB). Eligible participants were women with low-risk singleton pregnancies in their second trimester, enrolled in this prospective observational study. A Cervix Monitor (CM) device was designed with a vaginal probe comprising four tactile sensors and a single ultrasound transducer operating at 5 MHz. The probe enabled the application of controllable pressure to the external cervical surface, facilitating the acquisition of stress-strain data from both anterior and posterior cervical sectors. These data were used to calculate cervical elasticity, as a stress-to-strain ratio. CM examination data were analyzed for 127 women at 24 - 28 gestational weeks. PTB was observed in 6.3% (8 out of 127) of the cases. The preterm group exhibited a lower average cervical stress-to-strain ratio (elasticity) of 0.70±0.26 kPa/mm compared to the term group's 1.63±0.65 kPa/mm, with a significant p-value of 1.1×10-4. Diagnostic accuracy for predicting spontaneous preterm birth based solely on cervical elasticity data was found to be 95.0% (95% CI, 88.5–100.0). These findings suggest that measuring cervical elasticity with the designed tactile ultrasound probe could potentially predict spontaneous preterm birth in a cost-effective manner.

Chitosan and its derivatives as a biocompatible, biodegradable polymer that has been well-established in biotechnology and medicine as the nanogels and nanofilms forming material, has a number of practical applications in the field of the supply of medicines, food colloids, agrotechnology, as well. In this paper, the focus of attention is directed to the study of the physico-chemical principles of the formation of gels and nano-particles using fluorescence spectroscopy methods. We have obtained chitosan (Chit5) and pegylated chitosan (Chit5-PEG) particles with an average size of 170 or 400 nm, respectively by counterflow extrusion method. The paper presents three based fluorescent probes sensitive to the formation of chitosan particles: congo red, malachite green as well as covalently attached pyrene-label. Dyes fluoresce about an order of magnitude brighter in the composition of chitosan nanogel particles or in mscrogels. With these fluorescence probes, the pH- and temperature-dependent behavior of polymers was studied, and the influence of the genipin -based crosslinking agent on the gel formation parameters, such as kinetics and concentration dependence of the nanoparticles formation accompanied by sharply increases in the fluorescence intensity of dyes was evaluated. A sensitive approach for tracking gelation and including of small drug molecules and protein by FRET using a pyrene-tryptophan donor-acceptor pair is proposed using tryptophan or ovalbumin as fluorophores-donors. Upon nanogel formation FRET effect is observed manifested in sharp increase if the fluorescence intensity of the pyrene (acceptor). Thus, the application of the fluorescent probes with FRET function for monitoring the gelation and nanoparticles formation as well as drug encapsulation in chitosan-based parts, which have broad prospects in biomedical practice and food industry.

A novel fluorescent probe (C460@Tb-MOFs) was designed and synthesized through encapsulating the fluorescent dye 7-diethylamino-4-methyl coumarin into terbium-based metal-organic framework by a simple ultrasonic impregnation method. It is impressive that this dye-modified metal-organic framework can specifically detect styrene and temperature upon luminescence quenching. The sensing platform of this material exhibit great selectivity, fast response and good cyclability toward styrene detection. It is worth mentioning that the sensing process undergoes a distinct color change from blue to colourless, providing conditions for accurate visual detection of styrene liquid and gas. The significant fluorescence quenching mechanism of styrene toward C460@Tb-MOFs is explored in detail. Moreover, the dye-modified metal-organic framework can also achieve temperature sensing from 298 to 498 K with high relative sensitivity at 498 K. The preparation of functionalized MOFs composites by fluorescent dyes provides an effective strategy for the construction of sensors for multifunctional applications.

Friction is an important subject for sustainability due to problems associated with energy loss. Recent years, surface micro- and nanostructures have attracted much attention to reduce friction; however, suitable structures are still under consideration. Many functional surfaces are present in nature, such as the friction reduction surfaces of snake skins. In this study, we focused on firebrats, Thermobia domestica, living in narrow spaces such as under bark, so their surface frequently contacts with surrounding surfaces. We speculate that their body surface would be adapted to reduce friction. To investigate the firebrat surface functions, firebrat surfaces were observed by using a field-emission scanning electron microscope (FE-SEM) and a colloidal probe atomic force microscope (AFM), respectively. Results of surface observations by the FE-SEM revealed that firebrats are entirely covered with scales, whose surfaces have micro groove structures. Scale groove periods around the firebrat's head are almost uniform within a scale but vary between scales. AFM friction force measurements revealed that firebrat scale reduces friction by decreasing contact area between scales and a colloidal probe. The heterogeneity of groove periods of the scales suggest that it is difficult to fix the whole body in particular rough surfaces and that lead to be "fail-safe".

Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

In this study, a simple, easy and convenient fluorescent sensing system for detection of vascular endothelial growth factor (VEGF) based on VEGF aptamers, aptamer-complementary fluorescence-labeled probe and streptavidin magnetic beads was developed in only one single tube. The VEGF is the most important biomarker in cancer angiogenesis, and is investigated that serum VEGF level was various according to the different type and course of cancers. Hence, efficient quantification of VEGF is able to improve the accuracy of cancer diagnosis and precision of disease surveillance. In this research, the VEGF aptamer was designed to be able to bind with the VEGF by forming G-quadruplex secondary structures, and then the magnetic beads would capture the none-binding aptamers due to none steric interference, and finally, the fluorescence-labeled probes were hybridized with the aptamers captured by the magnetic beads. Therefore, the fluorescent intensity in the supernatant would specifically reflect the present of VEGF. After an overall optimization, the optimal conditions for detection of VEGF were as followed, KCl, 50 μM; pH 7.0; aptamer, 0.1 μM and magnetic beads, 10 μL (4 μg/μL). The VEGF could be well quantified within a range of 0.2-2.0 ng/ml in plasma, and the calibration curve possessed a good linearity (y = 1.0391x + 0.5471, r = 0.998). The detection limit (LOD) was calculated to be 0.0445 ng/mL according to the formula (LOD = 3.3×σ/S). The specificity of this method was also investigated under the appearance of many other serum proteins, and the data showed the good specificity in this aptasensor-based magnetic sensing system. This strategy provided a simple, sensitive and selective biosensing platform for detection of serum VEGF. Finally, it was expected that this detection technique can be promoted to more clinical applications.

In precision agriculture in fertigated crops it is necessary to optimize the use of water and chemicals, and enable efficient application of fertilizers in order to ensure the best yield and avoid risks of soil salinization and contamination. In this study, an intelligent system was developed with the objective of monitoring, in real-time, moisture and solute concentrations in soil cultivated with lisianthus (Eustoma grandiflorum, var. Casablanca) fertigated under a protected environment. During one crop cycle, moisture was monitored in soil solution using TDR100 reflectometer and solute concentrations were monitored with ceramic cup extractors. Plants were fertigated with a solution containing five potassium concentrations (50, 100, 150, 200, and 250 mg dm-3) applied when the soil reached moisture limits of 0.20, 0.15, 0.13, 0.11, and 0.09 cm3 cm-3. Experimental plots were arranged in a randomized block design in a 5 x 5 factorial scheme (moisture limits x potassium concentrations in soil solution), with four replicates. The proposed intelligent system enabled precise monitoring of moisture and electrical conductivity by TDR, and potassium, and other solute concentrations with extractors, being indicated for the management of lisianthus fertigation under greenhouse conditions with greater environmental safety and reduction of water consumption and risk of salinization.

In this paper, a new probe-fed wideband antenna with a circular patch and a coupled stacked ring is proposed. This antenna can be implemented by using suspended microstrip technique with total thickness of about 0.09 of center frequency wavelength. By using a novel feeding technique, in this antenna about 40 % reduction in area compared to similar works can be achieved. The obtained bandwidth in this antenna according to simulation results satisfying VSWR<2 is about 27.5 % from 5 to 6.6 GHz using two resonant frequencies. Also a comprehensive theoretical and parametric study is done in order to facilitate its designing in various frequency bands.

This work aimed to characterize a DBD plasma equipment through optical and electrical measurements, seeking to obtain a greater knowledge of the plasma production process and how it behaves through the adopted parameters, such as frequency and voltage applied between electrodes, at a fixed distance of 1.7 mm. In order to measure them, three different characterization techniques were applied. The first method was the Lissajous figures, a technique quite effective for a complete electrical characterization of DBD equipment. The second technique used was the Optical Emission Spectroscopy, a tool used for the diagnosis of plasma, being it possible to identify the excited species produced in filamentary and diffuse discharge in the plasma. And finally, the triple Langmuir probe technique was used to obtain the electron temperature and electron density. Based on this study, it was possible to identify the equipment efficiency in different regimes. The electron temperature measurement for both systems analyzed were 27.96 eV and 20.69 eV to the filamentary and diffuse regimes, respectively. The density of electrons number to these regimes were 1.09 × 10²¹ m⁻³ and 1.56 × 10²¹ m⁻³.

Directional dithering of a laser beam potentially limits the detection accuracy of a laser triangulation displacement probe. A theoretical analysis indicates that the measurement accuracy will linearly decrease as the laser dithering angle increases. To suppress laser dithering, a laser triangulation displacement probe with laser beam pointing control, which consists of a collimated red laser, a laser beam pointing control setup, a receiver lens, and a charge-coupled device, is proposed in this paper. The laser beam pointing control setup is inserted into the source laser beam and the measured object and can separate the source laser beam into two symmetrical laser beams. Hence, at the angle at which the source laser beam dithers, the positional averages of the two laser spots are equal and opposite. Moreover, a laser dithering compensation algorithm is used to maintain a stable average of the positions of the two spots on the imaging side. Experimental results indicate that with laser beam pointing control, the standard variance of the fitting error decreases from 0.3531 to 0.0100, the repeatability accuracy can be decreased from ±7mm to ±5 μm, and the nonlinear error can be reduced from ±6 %FS to ±0.16 %FS.

The main goal and essential parameter of laser light conversion is achieving higher laser brightness. That is the main reason why we take one light source to pump another. For every application the desired laser beam must have the highest available beam quality and highest achievable power. Usually by increasing one parameter, you incur a loss in the other. Here we present a method for delaying the reduction in beam quality by using a spatially structured optical pump for a membrane external cavity laser resonator. A slight increase in brightness is achieved under the same focusing conditions just by changing the pump intensity profile. By using a dynamically changing pump pattern a controllable output laser mode can be achieved.

Abundant of preparatory works have recognized that fluorescent sensors based on 8-aminoquinoline are popular tools to detect Zn2+ ions in environmental and biological applications. Along with these studies, researchers started to introduce a variety of carboxamido group into an 8-aminoquinoline molecule in forming 8-amidoquinoline derivatives. Therefore, this systematic review aims to introduce a general overview of the fluorophore 8-aminoquinoline as Zn2+ receptors and to provide comparisons of collected studies that related to 8-amidoquinoline derivatives as fluorophore probe of the sensor. According to PRISMA systematic searches strategy, 13 articles were analyzed for trends, research designs, results and discussion, subject samples, and remarks or conclusions. We found cross-sectional studies with four aspects in zinc sensing that have been targeted; binding studies via titration, detection's limit, interferences studies, and validation of the study. Hence, this paper also included assessments of those criteria and the trends of development of 8-amidoquinoline derivatives based-zinc fluorescent chemosensor. It also showed that most of the researches conducted in China. In conclusion, this study identified various research designs of fluorescent chemosensors based on 8-amidoquinoline prolong with the effectiveness and potential as a recognition probe to assist the detection of zinc. Hence, elucidation of those derivatives essential to be explored because more studies are needed to improve the sensing criteria of the zinc sensor

Abstract: Background: Vasoplegic shock syndrome(VSS) after an off-pump coronary artery bypass graft (OPCABG) is an extremely rare condition. Inotropic support is usually the first-line therapy though it can precipitate several complications or be ineffective. We report the first case of severe refractory VSS after OPCABG successfully treated with hydroxycobalamin. Methods: A 77-year-old gentleman underwent OPCABG for three vessels coronary artery disease. Preoperative LV ejection fraction was 28%, and the patient before surgery started sacubi-tril/valsartan titrated, then, to the highest dose. Surgery was uneventful and, by the end of the procedure, TEE showed improved biventricular contractility. Results: The patient was transferred to the ICU without inotropic support but he developed soon hypotension. TEE ruled out pericardial tamponade and confirmed fair contractility. Norepineph-rine was titrated to a medium-high dose, vasopressin was started and a Swan-Ganz catheter was placed. SVR was 480 dyn·s·cm−5. Despite aggressive pharmacologic treatment (including Methylprednisolone and Methylene blue), no improvements were noticed. 10 g of hydroxycobalamin were administered. One hour later hemodynamic status re-assessment showed SVR > 800 dyn·s·cm−5. Afterward, vasopressors were gradually reduced. Conclusions: Our case demonstrated the importance of adequate early treatment in VSS after OPCABG. For the first time, hydroxycobalamin was effectively used to restore homeostasis.

An inducer is one of the most important components of centrifugal pumps, whose presence will result in a significant increase in hydraulic performance and pump efficiency. The primary function of the inducer, however, is to delay the destructive phenomenon of cavitation, which has presented a considerable design challenge. Nevertheless, the amount of improvement and increase in inducer performance in both cavitation and non-cavitation modes depends critically on the radial laxity of the blade tip. As part of this study, the performance of the inducer in the cavitation state has been simulated and compared with the experimental data, which are in good agreement. This paper examines the effect of blade tip lagging on cavitation, and the results indicate that this will improve cavitation ­and delay this destructive phenomenon ­but will negatively affect the non-cavitation performance. With the increase in clearance, the range of the return current will increase at the tip of the inducer blade as well.

Background/Aims: Conflicting results have been reported regarding the interaction between proton pump inhibitors (PPIs) and clopidogrel. We investigated whether concomitant PPI use influenced the risk of recurrence in patients with stroke and myocardial infarction (MI). Methods: This study used two databases for different designs, the Korean National Health Insurance Service (NHIS) database for a self-controlled case series design, and the national sample cohort of the NHIS database converted to the Observational Medical Outcomes Partnership-Common Data Model version for a cohort study. Results: In the PPI co-prescription group, recurrent hospitalization with stroke occurred in 17.6% of the 8,201 patients with history of stroke, and recurrent MI occurred in 17.1% of the 1,216 patients with history of MI during 1 year. According to the self-controlled case series, the overall relative risk (RR) of recurrent stroke was 2.09 [95% confidence interval (CI); 1.83-2.38], and the RR showed an increasing trend with PPI duration. In the cohort study, there was a higher incidence of recurrent stroke in the PPI co-prescription group [Hazard ratio (HR): 1.34, 95% CI: 1.01-1.76, P=0.04]. The overall RR of recurrent MI was 1.47 (95% CI; 1.02-2.11) in the self-controlled case series; however, there was no statistically significant difference in recurrent MI in the cohort study (HR:1.42, 95% CI:0.79-2.49, P=0.23). The impact of individual PPIs on stroke and MI showed different patterns. Conclusions: PPI co-prescription with clopidogrel was associated with recurrent stroke; however, its association with recurrent MI remains inconclusive. The influence of individual PPIs should be clarified in the future.

Since Darwin’s “Power of movement in plants” the precise mechanism of oscillatory plant growth remains elusive. Hence the search continues for the hypothetical growth oscillator that regulates a huge range of growth phenomena ranging from circumnutation to pollen tube tip growth and stomatal movements. Oscillators are essentially simple devices with few components. A universal growth oscillator with only four major components became apparent recently with the discovery of a missing component, notably arabinogalactan glycoproteins (AGPs) that store dynamic Ca2+ at the cell surface. Demonstrably, auxin-activated proton pumps, AGPs, Ca2+ channels and auxin efflux “PIN” proteins, embedded in the plasma membrane, combine to generate cytosolic Ca2+ oscillations that ultimately regulate oscillatory growth: Hechtian adhesion of the plasma membrane to the cell wall and auxin-activated proton pumps trigger the release of dynamic Ca2+ stored in periplasmic AGP monolayers. These four major components represent a molecular PINball machine a strong visual metaphor that also recognizes auxin efflux “PIN” proteins as an essential component. Proton “pinballs” dissociate Ca2+ ions bound by paired glucuronic acid residues of AGP glycomodules, hence reassesses the role of proton pumps. It shifts the prevalent paradigm away from the recalcitrant “acid growth” theory that proposes direct action on cell wall properties, with an alternative explanation that connects proton pumps to Ca2+ signaling with dynamic Ca2+ storage by AGPs, auxin transport by auxin-efflux PIN proteins and Ca2+ channels. The extensive Ca2+ signalling literature of plants ignores arabinogalactan proteins (AGPs). Such scepticism leads us to reconsider the validity of the universal growth oscillator proposed here with some exceptions that involve marine plants and perhaps the most complex stress-test, stomatal regulation.

Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

Photoacoustic technology is a promising tool to provide morphological and functional information in biomedical research. To enhance the imaging efficiency, the reported photoacoustic probes have been designed coaxially involving complicated optical/acoustic prisms to bypass the opaque piezoelectric layer of ultrasound transducers, but leading to bulky probes and hindering the applications in limited space. Though the emergence of transparent piezoelectric materials helps to save the effort on the coaxial design, the reported transparent ultrasound transducers were still bulky. In this work, a miniature photoacoustic probe with an outer diameter of 4 mm was developed, in which an acoustic stack was made of the combination of transparent piezoelectric material and gradient-index lens as a backing layer. The transparent ultrasound transducer exhibited a high center frequency of ~47 MHz and a -6 dB bandwidth of 29.4%, which could be easily assembled with a pigtailed ferrule of a single-mode fiber. The multi-functional capability of the probe was successfully validated through the experiments of fluid flow sensing and photoacoustic imaging.

Novel cultivation technologies demand the adaptation of existing analytical concepts. Metabolic flux analysis (MFA) requires stable-isotope labeling of biomass-bound protein as the primary information source. Obtaining the required protein in cultivation set-ups where biomass is scarce or inaccessible due to low cell densities and cell immobilization is difficult to date. We developed a non-disruptive analytical concept for 13C-based metabolic flux analysis based on secreted protein as an information carrier for isotope mapping in the protein-bound amino acids. This "metabolic flux probe" (MFP) concept was investigated in different cultivation set-ups with a recombinant, protein-secreting yeast strain. The obtained results grant insight into intracellular protein turnover dynamics. Experiments under metabolic but isotopically nonstationary conditions in continuous glucose-limited chemostats at high dilution rates demonstrated faster incorporation of isotope information from labeled glucose into the recombinant reporter protein than in biomass-bound protein. Our results suggest that the reporter protein was polymerized from intracellular amino acid pools with higher turnover rates than biomass-bound protein. The latter aspect might be vital for 13C-flux analyses under isotopically nonstationary conditions for analyzing fast metabolic dynamics.

Meprin α is a zinc metalloproteinase (metzincin) that has been implicated in multiple diseases, including fibrosis and cancers. It has proven difficult to find small molecules that are capable of selectively inhibiting meprin α, or its close relative meprin β, over numerous other metzincins which, if inhibited, would elicit unwanted effects. We recently identified possible molecular starting points for meprin α-specific inhibition through an HTS effort (see part I, preceding paper). In part II we report the optimization of a potent and selective hydroxamic acid meprin α inhibitor probe which may help define the therapeutic potential for small molecule meprin α inhibition and spur further drug discovery efforts in the area of zinc metalloproteinase inhibition.

The solar heat pump system based on photovoltaic photothermal (PV/T) modules is a new technology that integrates photovoltaics and heat reutilization. It can improve the efficiency of photovoltaic conversion and recovery the remaining heat generated during the photoelectric conversion process, thereby improving the comprehensive efficiency of the whole system. Simulink software is a visual simulation tool, which has the advantages of strong applicability, clear simulation structure and calculation process. The design of its graphical programming greatly simplifies the user modeling process and allows for direct viewing of results, therefore improving the simulation efficiency. At present, there is little research on simulation of solar heat pump systems with PV/T modules based on Simulink software. In this paper, the mathematical models of each component contained in the PV/T solar heat pump system were established based on the system working principle, energy conservation equations and some empirical formulas, and then the operation of the system was simulated by the Simulink software. Due to the operation characteristic of PV/T modules is the key influencing factor for the whole system performance, the model and simulation process for PV/T modules were introduced in detail. The results showed that the surface temperature of PV/T modules under different operating conditions was significantly lower than that of ordinary photovoltaic panels, and the temperature change amplitude was lower. As results, the power generation and photovoltaic conversion efficiency were significantly improved.

The generation and maintenance of membrane potential is considered a fundamental element of the cellular machinery. They are based on elements of physics and chemistry. Mathematics is used to validate the equations and evaluate the results. However, this computation process can lead to a misunderstanding of the phenomena involved or to the masking of crucial events. It is even possible that the calculation no longer corresponds to the hypothesis considered. Membrane theory is no exception to these trivial considerations, which are essential for normal theory validation.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

Cryptococcus neoformans causes meningoencephalitis in immunocompromised individuals, which is treated with Fluconazole (FLC) monotherapy when resources are limited. This can lead to azole resistance, which can be mediated by overexpression of ABC transporters, a class of efflux pumps. ABC pump-mediated efflux of FLC is also augmented in 10-generation old C. neoformans cells. Here, we describe a new ABC transporter Afr3 (CNAG_06909), which is overexpressed in C. neoformans cells of advanced generational age, that accumulate during chronic infection. The delta-afr3 mutant strain showed higher FLC susceptibility by FLC E-Test strip testing and also by a killing test that measured survival after 3 h FLC exposure. Furthermore, delta-afr3 cells exhibited lower Rhodamine 6G efflux compared to the H99 wild type cells. Afr3 was expressed in the Saccharomyces cerevisiae AD-delta strain, which lacks several drug transporters, thus reducing background transport. The AD-delta + Afr3 strain demonstrated a higher efflux with both Rhodamine 6G and Nile Red, even though the FLC MICs were not changed. Characterization of the delta-afr3 mutant revealed unattenuated growth but a prolongation (22%) of the replicative life span. In addition, delta-afr3 exhibited decreased resistance to macrophage killing and attenuated virulence in the Galleria mellonella infection model. In summary, our data indicate that a novel ABC pump Afr3p, which is upregulated in C. neoformans cells of advanced age may contribute to their enhanced FLC tolerance, by promoting drug efflux. Lastly, its role in macrophage resistance may also contribute to the selection of older C. neoformans cells during chronic infection.

Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

A wide variety of pump and treat methods like chemical precipitation, adsorption, ion exchange and reverse osmosis have been trialled for many decades for fluoride removal from groundwater, but the problem of fluoride contaminated water remains in many parts of the world largely because these processes require constant monitoring, are expensive to implement and maintain at decentralised scale due to lack of reticulation infrastructure, and possess sludge disposal problem. This paper presents an overview of various fluoride removal processes and the limitations associated with each process and the application of in-situ permeable reactive barrier for remediating fluoride contaminated groundwater is explored, which displays the potential to be a cost effective, low maintenance and energy intensive technology.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

This article presents the possibilities of using ferrite absorption material for shielding rooms with medical devices in order to additionally protect them against the limits of the electric component of the E field, which are up to 61 V/m. These values may appear in connection with the currently launched 5G system operating in the high-band frequency range, i.e. 28 GHz and 38 GHz, and may cause negative effects on the operation of medical devices. The possibilities of using ferrite absorption material for shielding rooms with medical devices were determined based on the results of measurements of the electrical properties of the ferrite material performed using two methods: the reflection method and the free space method. In the article, the complex electrical permittivity and complex magnetic permeability were determined for a ferrite plate based on measurements of the reflection coefficient and the transmission (attenuation) coefficient. The presented calculation and measurement results were used to show the properties of the ferrite material in the frequency range from 15 GHz to 45 GHz and to show the possibility of using it for shielding rooms as a material absorbing electromagnetic waves in this frequency range.

Hoechst 33342 (H33342) is a fluorescent probe that is commonly used to stain DNA of living cells. To do so, it needs to interact with and permeate through cell membranes. The pH of biological media may vary quite significantly and this influences H33342 ionization state, and may change its rate of permeation through biomembranes. In this work, we address the effect of pH in the association of H33342 with lipid bilayers using a combined experimental and computational approach. The partition of H33342 to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) lipid membranes was experimentally quantified using fluorescence spectroscopy and isothermal titration calorimetry (ITC) measurements. Quantum chemical calculations were performed to select the most stable isomer of H33342 for the overall charges 0, +1, and +2, expected to predominate across the 5 &lt; pH &lt; 10 range. The interaction of these isomers with POPC bilayers was then studied by both unrestrained and umbrella sampling molecular dynamics simulations. While probe insertion occurs for all ionization states, with similar overall equilibrium location, orientation was found to depend on the probe charge, with the neutral form lying mostly parallel and the doubly charged displaying a significant tilt relative to the membrane plane. Both experimental results and computational free energy profiles indicate that the partition coefficient of H33342 displays a small variation over a wide pH range, not exceeding one order of magnitude. The enthalpy of interaction is negative and is larger at lower pH values. This suggests efficient hydrogen bonding between the probe and the lipid, namely for the protonated +2 form. The relatively high lipophilicity obtained for the charged species contrasts with the decrease in their general hydrophobicity as estimated from water and octanol partition. This highlights the distinction between lipophilicity and hydrophobicity, and the importance of considering association with lipid bilayers when predicting the affinity for biomembranes.

Background:Fontan completion is the last stage of univentricular repair, which drains the inferior vena cava against gravity to a higher-pressure pulmonary arterial circulation. The passivity and anti-gravity nature of this circulation render a failing Fontan, not an uncommon encounter, twenty years ago, Rodefeld and colleagues, decided to explore the feasibility of vascular pumps to support the passive nature of Fontan circulation, and since then, trials are still ongoing, and we aimed through this review to wrap up the results of these trials. Methods:A literature review has been conducted, to identify any in vivo or in vitro trial of a Fontan assist device. Several outcome parameters determined whether the trial will be included or not in this review, including, the flow rate of a pump if applicable, the number of compressions per minute if a compression device has been used, the resultant flow rate, the inferior and superior vena cava pressures, associated with each setting of the respective device, and any evidence of hemolysis or clotting within the circuit. Results:A total of ten trials have been included, with 23 different settings. Three designs have been identified, out of which two fall within the pump design, namely the connecting chamber and the intravascular pump designs; only one trial explored the possible use of a compression device. The commonest design encountered in in-vivo trials was the intravascular pump (67%). No reports of significant hemolysis or thrombosis were found. An increasing flow rate beyond 5L/min was associated with a negative outcome in the connecting chamber design, increasing upstream pressure in the SVC, while intravascular pumps did not display this limitation. Conclusion:Univentricular heart patients are a relatively small population, with very extensive needs, despite twenty years of trials, no study has yet concluded the optimal design or settings for a Fontan assist device. In this review, we identified that the intravascular pump remains the most practical design, due to its easy mode of insertion, and that it is not faced with the limitation or risk of increasing upstream resistance. There is still a long way to conclude its use as other designs such as compression devices have not yet been fully studied.

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

Mycobacterium tuberculosis is a leading cause of human mortality worldwide and the emergence of drug-resistantstrains, demands the discovery of new classes of antimycobacterials that can be employed in the therapeutic pipeline. Previously, a secondary metabolite Chrysomycin A, isolated from Streptomyces sp. OA161 was shown to have potent bactericidal activity against drug-resistant clinical isolates of M. tuberculosis and different species of mycobacteria. The antibiotic inhibits the mycobacterial topoisomerase I and DNA gyrase leading to bacterial death, but the mechanisms that could cause resistance are currently unknown. To further understand the resistance mechanism, spontaneous resistance mutants were isolated and subjected to whole-genome sequencing. Mutation in a Tet^R family transcriptional regulator MSMEG_1380 was identified in the resistant isolates and was close to an operon encoding membrane protein MSMEG_1381 and MSMEG_1382. Sequence analysis and modeling studies indicated that they are components of the Mmp family of efflux pumps and over-expression of either the operon or individual genes conferred resistance to chrysomycin A, isoniazid, and ethambutol that are in TB therapy. Our study highlights the role of membrane transporter proteins in conferring multiple drug resistance and the utility of recombinant strains overexpressing membrane transporters in the drug screening pipeline.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

During operation, the support bracket is the main part to withstand the axial loads of the pumped storage unit. Moreover, the effects of axial loads including the hydraulic thrust of runner flow and the weight of runner body may cause the support bracket deformation and fatigue damage. For the safe and stable operation, the simulation of the axial force and the structural analysis of the support bracket of a pumped storage unit was carried out in this paper. The CFD simulation result has revealed the variation rule of the axial force in different operating conditions. Using ANSYS Mechanical, the static stresses and deformation of support bracket with axial loads were calculated. The results release the location and variations of maximum stress and maximum deformation caused by the axial loads. By comparing the predicted maximum axial force with the admission force calculated by the structural analysis, it is found that the axial force of the researched machine is within the safe range. This study provides the reference for the safety and stable operation of the pumped storage unit.

A pump station is a very important flood control facility for mitigating inundation of urban lowland areas. It is not easy to secure a site to increase the capacity of a pump station in an urban area because of various limitations or to maximize the discharge capacity of the pump sump. Adding a facility to improve the pump capacity of a pump station may affect the flow characteristics, such as unexpected increases in the flow velocity and vorticity, and cause severe problems with operating the pump station. To solve those problems, anti-vortex devices (AVDs) have been developed and adopted for appropriate design standards. The Korean design criteria for AVDs are based on experience and foreign standards because not enough data on the AVD are available. In this study, the flow in the sump was numerically simulated at various AVD heights to collect information on improving the design and efficiency of a pump station. Consequently, an appropriate height for the AVD and changes in the flow pattern and vortex in the pump sump were determined and compared with 12 cases of inflow conditions with respect to the vertical location.

Since Hydrogen Sulfide (H2S) was recognized as a gas transmitter, its detection and quantifica-tion have become a hot research topic among chemists and biologists. In this area. fluorescent probes have shown great advantages: fast and strong responds, low detection limit and easy ma-nipulation. Here we developed a new fluorescent probe that detected H2S selectively among various bioactive and inorganic salts. This probe was based on the core structure of fluorescein and reacted with H2S through azide-reduction. Great linearity was achieved correlating fluores-cence intensity and H2S concentrations in solution. The detection of H2S in cancer cells was also achieved.

The crucial phenomenological and experimental predictions for new physics are outlined, where the number of problems of the Standard Model (neutrino masses and oscillations, dark matter, baryon asymmetry of the Universe, leptonic CP-violation) could find their solutions. The analogies between the cosmological neutrino mass scale from the early universe data and laboratory probes are discussed and the search for new physics and phenomena.

Uniform water soluble MoS2 quantum dots (WS-MSQDs) are synthesized via a sequential combination of sintering/etching/exfoliation method and solvothermal route. The obtained WS-MSQDs with average size of approximately 3.4 nm exhibit sufficient water solubility and remarkable fluorescence properties. The WS-MSQDs have been utilized as a probe for detection of Fe3+ ions with high selectivity and specificity. Furthermore, the WS-MSQDs exhibit high fluorescence stability under different conditions. Finally, the WS-MSQDs are successfully applied for the fluorescence imaging of Fe3+ in living cells, which exhibited practical potential for biomedical applications.

The present study describes the activities performed to test a new method for measuring the mobility of polycyclic aromatic hydrocarbons (PAHs) in the solid phase of sediments within the context of environmental pollution risk assessment. The method is based on the design of a new configuration (new materials) of the commercial passive sampler Chemcatcher as probe for predicting the bioavailability of persistent organic pollutants in marine sediments (or in water saturated soils).

An analysis of form and size of the fatigue wear of gear wheel top layer of the prototype oil pump (type 3PW-BPF-24) is presented in the publication. The object of research was subject to endurance tests, so called labour resource test. During this test the pump was loaded in cycles with maximal working pressure. Additionally, continuous monitoring tests of exploitational and environmental parameters were conducted. After a completion of the endurance test the noticed superficial defects due to a phenomenon of the top layer fatigue and previously applied thermochemical treatment were measured and described. The work was finished with an analysis of obtained results and conclusions concerning a selection optimization of the thermal treatment parameters. Taking into consideration the presented results (suggestions) in the technology of improving strength prop-erties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fa-tigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Proton-pump inhibitors (PPIs) are the most administered first-line treatment for eosinophilic esophagitis (EoE). However, only around half of EoE patients respond histologically to PPI at double dosage. In addition, 70% of responders maintain EoE in remission after tapering the PPI dose. In order to avoid endoscopy with biopsies − the only accurate method of assessing PPI response − efforts have been made to identify PPI responder patients. Clinical or endoscopic features and biomarkers evaluated so far however, have not proved good enough in predicting PPI response. Although new approaches based on omics technologies have uncovered promising biomarkers, the specialized and complex procedures required are difficult to implement in clinical settings. Alternatively, PPI pharmacogenetics based on identifying variations in CYP2C19 and STAT6 genes have shown promising results in EoE, and could easily be performed in most laboratories. Other genetic variations have also been associated with PPI response and may explain those cases not related to CYP2C19 or STAT6. Here, we give an overview of PPI treatment in EoE and evidence of how genetic variations in CYP2C19 and other genes could affect PPI effectiveness, and also discuss studies evaluating the role of pharmacogenetics in predicting PPI response in patients with EoE.

This paper presents a parametric study of the multistorey hydro-powered pump, known as "Bunyip," which has demonstrated significant potential in contributing to rural regions. The study aims to understand the underlying physics of the system and enhance its hydraulic performance. A transient three-dimensional model using the commercial Computational Fluid Dynamics (CFD) tool Ansys-Fluent is utilized to gain insights into the fundamental flow mechanics, operational efficiency, standard capacity, and relative delivery. The investigation involves an initial assessment of performance for three Bunyip devices based on manufacturing data. Parametric analysis is conducted, and a parametric dataset is generated through meticulous application and numerical modelling. The CFD results are validated against experimental data. Three design configurations are considered, and 58 sets of varied input parameters are examined. The best design configuration is evaluated against five cases of conventional hydro-power pump systems. The results indicate that a smaller diameter of the pressure chamber and a higher supply head lead to higher pressure, achieving a target head of 3 m with 15% efficiency and a flowrate of 11.82 l/min.

An experimental investigation on the heat pump performance improvement equipped with the two-phase ejector called “an ejector-expansion heat pump (EEHP)” is proposed. The system performance of the EEHP is compared with a vapour-compression heat pump (VCHP). The improvement potential is determined and discussed. The heat pump test system is constructed which is based on a water-to-water heat pump. It can be experimented with both EEHP and VCHP. The two-phase ejector with the cooling load up to 2500 W is installed for experiment. The results show that the EEHP always produces a higher heating rate and COP than the VCHP throughout the specified working conditions. The heating COP is increased by 5.7-12.2% depending on the working conditions. It is also that under the same heat sink and heat source temperature, the EEHP can produce lower compressor discharge temperature and lower compressor pressure ratio than the VCHP. This is evidence that the two-phase ejector can provide better compressor working characteristics which yields a longer compressor lifetime. It is demonstrated that a key to the performance of the EEHP is the expansion pressure ratio. A larger expansion pressure ratio yields a higher improvement potential when compared with the VCHP.

Double suction centrifugal pump installed along the Yellow River faces the serious sediment erosion due to the high sediment content which cause the poor operation efficiency of pump unit. The particle motion characteristics and erosion characteristics in the pump under different flow rates and different particle concentrations were numerically simulated based on the particle track model of solid-liquid two-phase flow. The results show that the flow rate has a significant effect on the particle tracks and the erosion caused by the particles in the impeller. The total erosion rate is positively correlated with the flow rate, and increases with the increase of flow rate. The vortex and secondary flow in the impeller have obvious influence on the particle trajectory, which increases the particle concentration at the trailing edge of the pressure surface and intensifies the impact erosion in this area. The particles carried by the vortex intensifies the local erosion. The particle concentration mainly affects the erosion rate, but has little effect on the erosion position. The in-fluence of flow rate on the pump erosion is greater than that of the particle properties. These results provide a reference for optimization of the design of anti-erosion blades of the double-suction pump and regulation-operation of pumping station.

Background: COVID-19 is a disease of the elderly as 95% of deaths related to COVID-19 occur in people over 60 years of age. Despite the urgent need for a preventive treatment there are currently no serious leads, other than the vaccination. Objective: To find a preventive treatment of COVID-19 in elderly patients. Design: Retrospective case-control study. Setting: Robertsau Geriatric Hospital of the University Hospitals of Strasbourg, France. Patients: 179 elderly patients who had been in contact with the SARS-CoV-2, of whom 89 had tested RT-PCR-positive (COVID-pos) for the virus and 90 had tested RT-PCR-negative (COVID-neg). Measurements: Treatments within 15 days prior to RT-PCR (including antihypertensive drugs, antipsychotics, antibiotics, nonsteroidal anti-inflammatory drugs, proton pump inhibitors (PPIs), paracetamol, anticoagulant, oral antidiabetics (OADs), corticosteroids, immunosuppressants), comorbidities, symptoms, laboratory values, and clinical outcome were all collected using the electronic patient record. Results: COVID-pos patients more frequently had a history of diabetes (P=.016) and alcoholism (P=.023), a lower leukocyte count (P=.014) and a higher mortality rate– 29.2% versus 14.4% – (P=.014) when compared to COVID-neg patients. Patients on PPIs were 2.3 times less likely (odds ratio [OR] = 0.4381, 95% confidence interval [CI] [0.2331, 0.8175], P=.0053) to develop COVID-19 infection, compared to those not on PPIs. No other treatment decreased or increased this risk. COVID-19 patients on antipsychotics (P=.0013) and OADs (P=.0166) were less likely to die. Limitations: retrospective study. Conclusion: PPIs treatment lowered the risk of development of COVID-19 infection, and antipsychotics and OADs decreased the risk of mortality in geriatric patients. If further studies confirm this finding, PPIs could be used preventatively in the elderly in this pandemic context. Moreover, OADS and antipsychotics should be tested in clinical trials.

We performed a systematic review and meta-analysis to evaluate the role of gastric acid suppressant use on outcomes of tyrosine kinase inhibitors (TKIs) and oral chemotherapy. We identified all researches evaluating the effect of GAS use on patients receiving oral chemotherapy or TKIs for solid tumors. The pooled hazard ratios (HRs) and 95% confidence interval (95% CI) for overall survival (OS) and progression-free survival (PFS) were calculated with fixed-effects or random-effects model. The study population included n=16 retrospective studies and 372,418 patients. Series concerned gastrointestinal tract tumors (n=5 studies), renal cell carcinomas (RCC, n=3 studies), non-small cell lung cancers (NSCLC, n=5 studies), and soft tissue sarcomas or mixed histologies solid tumors in n=3 studies. The pooled HRs for OS and PFS were 1.31 (95% CI: 1.20–1.43; P<01) and 1.3 (95%CI 1.07-1.57; P<0.01) for GAS and no GAS users, respectively. Only studies of EGFR mutated NSCLC patients receiving TKIs and those with colorectal cancer receiving oral chemotherapy showed a significant correlation between GAS and poor survival. Our study supports the evidence of a possible negative impact of concomitant GAS therapy on survival outcomes of patients receiving oral anti-cancer drugs.

Abstract: The spectral and dynamic properties of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO)

The study sought to determine the rate of discordant results between genotypic and phe-notypic tests for the diagnosis of drug resistant tuberculosis (DR-TB). Sputum samples and cultured isolates from suspected DR-TB patients were respectively analysed for My-cobacterium tuberculosis by Xpert® MTB/RIF (Cepheid, USA) and Line Probe Assays (LPA) (Hain, Germany). Discrepant Rifampicin (RMP) resistant results were confirmed using BACTEC MGIT960 (BD, USA). Of 224 RMP-resistant by Xpert MTB/RIF, 5.4% were suscep-tible to RMP by LPA. MGIT960 showed 75% agreement with LPA. Discrepancy was at-tributed to either heteroresistance or DNA contamination during LPA testing in 58.3% of cases. In 25% of samples showing agreement in RMP resistance between Xpert MTB/RIF and MGIT960, discrepancy was attributed to laboratory errors causing false RMP suscep-tible results with LPA. Of 16.7% of cases, discrepancy was attributed to false RMP suscep-tible results with Xpert MTB/RIF. Of 224 isolates, susceptibility to isoniazid (INH) by LPA was performed in 73.7% RMP resistant isolates, of which, 80.6% were resistant. All RMP resistant isolates by Xpert MTB/RIF were confirmed in 98.5% by LPA if TB isolates were resistant to INH, but only confirmed in 81.3% if TB isolates were INH susceptible (ρ < 0.001). In conclusion, Laboratory errors should be considered when investigating dis-cordant results.

The hydrodynamic behavior of the air-acetic acid system in a bubble column is studied using a differential pressure transmitter, double probe optical fiber probe, and the electrical resistance tomography (ERT) technique. The superficial gas velocity ranges from 0.016 to 0.094 m/s under ambient temperature and pressure. The influences of viscosity and surface tension on gas holdup, bubble rising velocity, and bubble chord distribution in the column are discussed with different mass fractions of an acetic acid solution. The results show that as the mass fraction of acetic acid increases, the surface tension of the liquid phase decreases, and the viscosity first increases and then decreases. This causes the gas holdup in the column to first increase and then decrease, and reaches the maximum value at an acetic acid mass fraction of 55% to 60%. The rising velocity of the bubbles in the column is high in the central region and has a low-value distribution near the wall. The bubble chord length distribution is concentrated, and the distribution of the bubble chord length in the column becomes narrow with any decrease in surface tension. Studying the hydrodynamic behavior of a bubble column with the air-acid system is of great significance considering the absence of data on air-organic acid systems.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

We study electrohydrodynamic (EHD) linear (in)stability of microfluidic channel flows, i.e. the stability of interface between two-shearing viscous (perfect) dielectrics exposed to an electric field in large aspect ratio microchannels. We then apply our results to particular microfluidic systems known as electroosmotic (EO) pumps. Our results are detailed analytical expressions for the growth rate of two-dimensional EHD modes in Couette-Poiseuille flows in the limit of small Reynolds number ($R$); the expansions to both zeroth- and first-order-$R$ are considered. The growth rates are complicated functions of viscosity-, height-, density- and dielectric-constant ratio, as well as of wavenumbers and voltages, and to our knowledge have not been presented before in literature. To make the results more useful, e.g., for voltage-control EO pump operations, we also derive equations for the impending voltages of the neutral stability curves that divide stable from unstable regions in voltage-wavenumber stability diagrams. The voltage equations and the stability diagrams are given for all wavenumbers. We finally outline the flow regimes in which our first-order-$R$ voltage corrections could potentially be experimentally measured. Our work gives the insight into the coupling mechanism between electric field and shear flow in parallel-planes channel flows, correcting an erroneous attempt from literature. Our general analysis enables us also to refine the renowned instability mechanism due to viscosity stratification, i.e., the case of pure shear instability, when the first-order-$R$ voltage correction equals zero.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

In order to improve the operation performance of the multi-stage double-suction centrifugal pump and reduce the internal energy loss of the pump, this paper proposes a single-objective optimization design method based on non-hierarchical response surface model (RSM) and the multi-island genetic algorithm (MIGA). Nine parameters, such as the blade outlet width and blade wrap angle, were used as design variables, and the optimization objective was the efficiency under design conditions. In total, 149 sets of valid data were obtained under the latin hypercube sampling method (LHS), the corresponding thresholds were set for efficiency and head, and 99 sets of valid data were obtained. A cross-validation analysis of the sieved data was carried out based on non-hierarchical RSM, global optimization of the efficiency was carried out using MIGA, and numerical verification was carried out via CFD. The research results show that compared with hierarchical RSM, non-hierarchical RSM can approximate the nonlinear relationship between the objective function and the design variables with higher accuracy, and the model fitting R2 value was 0.919. The efficiency was improved by 3.717% after optimization. The overall prewhirl of the impeller inlet after optimization decreased, the internal speed of the volute significantly improved, the large-area vortex at the volute and the outlet pipe was eliminated, the impact loss at the volute separating tongue disappeared, and the overall hydraulic performance of the pump was improved. The total entropy output value of the optimized pump was reduced by 4.79 (W/K), mainly concentrated in the reduction in the entropy output value of the double volute, and the overall energy dissipation of the pump was reduced.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

The main goal of this paper is to show that Bayesian optimization could be regarded as a general framework for the data driven modelling and solution of problems arising in water distribution systems. Hydraulic simulation, both scenario based, and Monte Carlo is a key tool in modelling in water distribution systems. The related optimization problems fall in a simulation/optimization framework in which objectives and constraints are often black-box. Bayesian Optimization (BO) is characterized by a surrogate model, usually a Gaussian process, but also a random forest and increasingly neural networks and an acquisition function which drives the search for new evaluation points. These modelling options make BO nonparametric, robust, flexible and sample efficient particularly suitable for simulation/optimization problems. A defining characteristic of BO is its versatility and flexibility, given for instance by different probabilistic models, in particular different kernels, different acquisition functions. These characteristics of the Bayesian optimization approach are exemplified by the two problems: cost/energy optimization in pump scheduling and optimal sensor placement for early detection on contaminant intrusion. Different surrogate models have been used both in explicit and implicit control schemes. Showing that BO can drive the process of learning control rules directly from operational data. BO can also be extended to multi-objective optimization. Two algorithms have been proposed for multi-objective detection problem using two different acquisition functions.

The adoption of Pump as Turbines (PATs) both in small scale hydroelectric plants and water supply systems has brought different advantages, the most recognized being cost-effectiveness as compared to other hydroturbines. However, due to their lack of flow control ability, their intolerance to off-design operations constitutes one tough shortfall. Moreover, this technology’s newness leads to PAT flow dynamics still being ununderstood even to date. Therefore, this study intends to numerically investigate the mixed flow PAT’s pump mode flow dynamics for five operating conditions expanding from optimum (1QBEP) to deep part-load (0.41 QBEP) conditions. Moreover the effect of runner blade angle on the same has been investigated where three angles namely -2°, 0°, and 2° have been considered. PAT flow stability was found to deteriorate as the flow decreased, where associated pressure pulsation level worsened at different flow zones. In addition, the blade angle increase led correspondingly increasing flow unsteadiness and pressure pulsation levels, where the pulsation frequencies from rotor-stator interactions were dominant for most of flow zones. This study’s findings are of a crucial importance to both scientific and engineering communities as they contribute to thorough understanding of PAT flow dynamics.

When considering implementation of shallow geothermal energy as a renewable source for heating and cooling of the building, special care should be taken in hydraulic design of borehole heat exchanger system. Laminar flow can occur in pipes due to usage of glycol mixture at low temperature or inadequate flow rate. This can lead to lower heat extraction and rejection rates of the exchanger because of higher thermal resistances. Furthermore, by increasing flow rate to achieve turbulent flow and satisfactory heat transfer rate can lead to increase the pressure drop of the system and oversizing of circulation pump which leads to impairment of seasonal coefficient of performance at the heat pump. Most frequently used borehole heat exchanger system in Europe is double-loop pipe system with smooth inner wall. Lately, development is focused on implementation of different configuration as well as with ribbed inner wall which ensures turbulent flow in the system, even at lower flow rates. At a location in Zagreb, classical and extended thermal response test was conducted on three different heat exchanger configurations in the same geological environment. With classic TRT test, thermogeological properties of the ground and thermal resistance of the borehole were determined for each smooth or turbulator pipe configuration. Extended Steady-State Thermal Response Step Test (TRST) was implemented, which incorporate series of power steps to determine borehole extraction rate at the define steady-state heat transfer conditions of 0/-3°C. Results show that heat exchangers with ribbed inner pipe wall have advantages over classic double-loop smooth pipe design, in terms of greater steady state heat extraction rate and more favorable hydraulic conditions.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

A heat pump with thermal storage system is a system that operates a heat pump during night-time using inexpensive electricity; during this time, the generated thermal energy is stored in a thermal storage tank. The stored thermal energy is used by the heat pump during daytime. Based on a model of a dual latent heat storage tank and a heat pump, this study conducts control simulations using both conventional and advanced methods for heating in a building. Conventional methods include the thermal storage priority method and the heat pump priority method, while advanced approaches include the region control method and the dynamic programming method. The heating load required for an office building is identified using TRNSYS, used for simulations of various control methods. The thermal storage priority method shows a low coefficient of performance (COP), while the heat pump priority method leads to high electricity costs due to the low use of thermal storage. In contrast, electricity costs are lower for the region control method, which operates using the optimal part load ratio of the heat pump, and for dynamic programming, which operates the system by following the minimum cost path. According to simulation results for the winter season, the electricity costs using the dynamic programming method are 17% and 9% lower than those of the heat pump priority and thermal storage priority methods, respectively. The region control method shows results similar to the dynamic programming method with respect to electricity costs. In conclusion, advanced control methods are proven to have advantages over conventional methods in terms of power consumption and electricity costs.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Quantitative polymerase chain reaction (qPCR) is the gold standard approach for detecting a variety of pathogens either via probe-based or SYBR green detection chemistry. Generally, probe-based detection is more specific than SYBR green chemistry. This report describes work done in using a FAM probe targeting a specific segment of the human KRAS gene for detecting presence and relative abundance of the gene in human gastric CloTest samples. Results indicate ineffective detection of the human KRAS gene in samples that are shown to harbor the gene through a similar qPCR assay using SYBR green detection chemistry. Such observations point to inability of the designed FAM probe to bind to target segment of the human KRAS gene that suggests a region of rapid genomic evolution that require close surveillance in the public health community. Given its rapid genomic evolution, this probe region may be an important region in the human KRAS gene playing critical functional roles in either molecular recognition or other structural functions. Overall, human KRAS gene may be undergoing rapid genomic evolution, and qPCR probes targeting specific segment of the gene may be rendered ineffective in short time clinically, thereby, making SYBR green qPCR assay a more reliable choice.

This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant and tangent loss via closed form capacitance model and lift-off calibration process. Measurement error of dielectric constant, Δε_r is less than 2.5 % from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 3×10^-3.

Formalin-Fixed Paraffin Embedded (FFPE) tissues are a valuable resource in studying different markers and mechanistic molecules (protein, DNA and RNA) in order to understand the etiology of different cancers as well as many other diseases. Degradation and modification of RNA is the major challenge in utilizing FFPE tissue samples in medical research. Recently, non-protein coding transcripts long non-coding RNAs (lncRNAs), have gained significant attention due to their important biological actions and potential involvement in cancer. There is no validated method except qRTPCR or RNAseq to evaluate and study lncRNA expression. We have standardized and are reporting a sensitive Z probe based in situ hybridization method to identify, localize and quantitate lncRNA in FFPE tissues. This assay is sensitive to single transcript and localizes lncRNA in individual cells within tumor. We have characterized a tumor suppressor lncRNA-NRON (non coding repressor of NFAT), which is scarcely expressed, a moderately expressed oncogeneic lncRNA UCA1 (urothelial cancer associated 1), and a highly studied and expressed lncRNA MALAT1 (metastasis associated lung adenocarcinoma transcript1) in different cancers. High MALAT1 staining was found in colorectal, breast and pancreatic cancer. MALAT1 expression increased with the progression of the stage in colorectal cancer and invasiveness in breast cancer.

Autonomous aerial refueling technology is an effective solution to extend flight duration of unmanned aerial vehicles, and also a great challenge due to its high risk. For autonomous probe-and-drogue refueling tasks, relative navigation to provide relative position between the receiver aircraft and the refueling drogue is the first and essential step, and vision-based method is the most frequently used. A new monocular vision navigation sensor with image processing strategy consisting of the drogue detection method and the tracking method is developed for autonomous aerial refueling in this paper. In the drogue detection method, thresholding and mathematical morphology method are adopted to eliminate image interference, and contours extraction method is applied to obtain all contours, which are then subsequently checked to achieve target contour of drogue. In the tracking method, a rectangle of interest (ROI) of current frame image is determined by positioning results of last frame, and then processed by the previous drogue detection method. Finally, the proposed image processing strategy in monocular vision navigation sensor is validated using real flight images, which are captured from an autonomous aerial refueling testbed using a micro six-rotor aircraft as receiver aircraft.

In this study, we introduce the concept and construction of an innovative Digital Miniature Cathode Ray Magnetometer designed for the precise detection of magnetic fields. This device addresses several limitations inherent to magnetic probes such as D.C. offset, nonlinearity, temperature drift, sensor aging, and the need for frequent recalibration, while capable of oper-ating in a wide range of magnetic fields. The core principle of this device involves the utilization of a charged particle beam as the sensitivity medium. The system leverages the interaction of an electron beam with a scintillator material, which, then, emits visible light that is captured by an imager. The emitted scintillation light is captured by a CMOS sensor. This sensor not only rec-ords the scintillation light but also accurately determines the position of the electron beam, providing invaluable spatial information crucial for magnetic field mapping. The key innova-tion lies in the combination of electron beam projection, CMOS imager scintillation-based de-tection and digital image signal processing. By employing this synergy, the magnetometer achieves remarkable accuracy, sensitivity and dynamic range. The precise position registration enabled by the CMOS sensor further enhances the device's utility in capturing complex magnetic field patterns, allowing for 2D field mapping. In this work, the optimization of the probe's per-formance is tailored for applications related to the characterization of insertion devices in light sources, including undulators.

Microalloying of low carbon steel with niobium (Nb) and titanium (Ti) is standardly applied in high-strength low-alloy (HSLA) steels enabling austenite conditioning during thermo-mechanical controlled processing (TMCP), which results in pronounced grain refinement in the finished steel. The metallurgical effects of microalloying elements are related solute drag and precipitate particle pinning, both acting on the austenite grain boundary thereby delaying or suppressing recrystallization of the deformed grain. In that respect it is important to better understand the precipitation kinetics as well as the precipitation sequence in a typical Nb-Ti-microalloyed steel. Various characterization methods have been utilized in this study for tracing microalloy precipitation after simulating different austenite TMCP conditions in a Gleeble apparatus. Atom probe tomography (APT), scanning transmission electron microscopy in a focused ion beam equipped scanning electron microscope (STEM-on-FIB) and electrical resistivity measurements provide complementary information on the precipitation status and are correlated with each other. It will be demonstrated that accurate electrical resistivity measurements can monitor the general consumption of solute microalloys (Nb) during hot working which was complemented by APT measurements of the steel matrix. On the other hand, STEM revealed that a large part of Nb-containing particles during hot working are co-precipitated with titanium during cooling from the austenitizing temperature. Precipitates that form during cooling or isothermal holding can be distinguished from strain-induced precipitates by corroborating STEM measurements with APT results. APT specifically allows obtaining detailed information about the chemical composition of precipitates as well as the distribution of elements inside the particle. Electrical resistivity measurement, on the contrary, provides macroscopic information on the progress of precipitation and can be calibrated by APT. The current paper highlights the complementarity of these methods and shows first results within the framework of a larger study on strain-induced precipitation.

This paper presents tea leaves moisture monitoring system based on RF reflectometry techniques. The system was divided into two parts which are the sensor and reflectometer parts. The large coaxial probe was used as a sensor of the system. The reflectometer part plays a role as signal generator and also data acquisition. The reflectometer-sensor system was operated with a graphical user interface at 1.529 GHz at room temperature. The system was able to measure the moisture content of tea leaves ranging 0% m.c to 50% m.c on a wet basis. In this study, up to five kinds of tea leaves bulk were tested. The mean of absolute errors in the moisture measurement for tea leaves was ±2.

Objective: We report a case of acute pancytopenia and liver injury after concomitant administration of low-dose methotrexate (MTX), and high-dose esomeprazole and metamizole. Case summary: A 71-year-old patient with chronic systemic idiopathic erosive arthritis was admitted after a pelvic ring fracture. After hospital admission, she received MTX in addition to esomeprazole and metamizole. Subsequent laboratory tests revealed pancytopenia and elevated liver enzymes. The follow-up clinical examinations were unremarkable, with the exception of sub-febrile temperatures. Further investigations did not detect a definitive etiology. Due to the suspicion of methotrexate-induced hematotoxicity and hepatotoxicity, antagonizing therapy with calcium folinate was administered, after which the blood counts and liver parameters normalized. Discussion: Due to the administration of high-dose metamizole immediately before the administration of low-dose MTX, the pre-existing hematotoxic pharmacodynamic effect of MTX was acutely enhanced by that of metamizole, although folic acid was administered preemptively. In addition, the concomitant administration of high-dose esomeprazole and normal dose torasemide resulted in a pharmacokinetic interaction with MTX by decreasing its renal secretion and elimination, further enhancing the concentration-dependent hematotoxic and hepatotoxic side effects of MTX. Conclusions: The relatively high demand for analgesics in patients with chronic rheumatic diseases already being treated with MTX and proton pump inhibitors necessitates that clinicians consider drug-drug interactions as potential causes of adverse drug reactions after the administration of metamizole or nonsteroidal anti-inflammatory drugs. In this category of patients, it is strongly recommended to switch to analgesics of other classes.

We conducted this systematic review with the objective to understand the efficacy and safety of proton pump inhibitors [PPIs] in the pediatric population. We have used PubMed to identify randomized controlled trials [RCTs] published between 1st June 2010 and 30th June 2023, in patients from birth to 18 years old, with gastroesophageal reflux disease [GERD], who received treatment with any PPI. The literature yielded 76 articles and 13 met inclusion criteria. For infants, PPIs were equal to placebo in reducing GERD symptoms in 4 articles. In 1, the number of GER episodes and esophageal acid exposure were lower in infants who received PPIs and left lateral position, but there was no significant improvement in symptoms. In another publication, the combination of PPIs and feeding modifications [FM] was not more effective than PPIs alone. For children and adolescents, PPIs were effective in improving symptoms and achieving mucosal and histological healing, which was subsequently maintained. To conclude, PPIs are not effective to reduce symptoms related to GERD in infants, but are effective in older children, along with histological remission. Generally, PPIs are well tolerated, but it is important to not forget the possible adverse events [AE], especially if they are used for a long time.

Domestic heating systems in the UK and across northern Europe are responsible for a substantial fraction of their countries’ carbon footprints. In the UK the vast majority of home space heating is via natural gas boilers with ’wet’ hydronic radiator systems. Most of those use TRVs (Thermostatic Radiator Valves) to avoid overheating, improve comfort and save energy. To meet Net Zero targets 20 million such UK gas systems may be retrofitted with heat pumps. Heat pump system designers and installers are cautious about retaining TRVs in such retrofitted systems in part because of worries that TRV temperature setbacks that lower heat demand may actually raise heat pump electricity demand in a "bad setback effect", thus wasting energy. This paper presents a new view of heat pump control and provides the first exploration of this issue, modelling one such industry claim, and finds that though real it should not apply to typical UK retrofits with weather compensation. The energy efficiency benefits of TRVs for older and partly-occupied homes, and to keep bedrooms cooler, remain valid. Comfort-seeking householders and installers should know that setting ’stiff’ temperature regulation may invoke the bad setback effect and cost dearly in energy and carbon footprint.

Dacomitinib is an irreversible epidermal growth factor receptor (EGFR) tyrosine kinase inhibitor indicated for the treatment of patients with advanced non-small cell lung cancer (NSCLC) and EGFR-activating mutations. Proton pump inhibitors decreased dacomitinib exposure. This anal-ysis summarizes the effect of H2RA on dacomitinib exposure. A within-patient comparison of steady-state trough concentrations (Ctrough,ss) of dacomitinib and its active metabolite and active moiety with and without concomitant use of H2RA was conducted using a linear mixed effects model with pooled data from 11 clinical studies in patients with NSCLC. An oral absorption PBPK model was constructed and verified using clinical PK data after a single dose of dacomitinib in healthy volunteers to estimate the effect of gastric pH altered by an H2RA on dacomitinib PK. The adjusted geometric mean of dacomitinib Ctrough,ss of dacomitinib parent, metabolite and active moiety following co-administration with H2RA was approximately 86%, 104% and 100% relative to that following dacomitinib 45 mg administration without H2RA (P>0.05). The PBPK modeling showed negligible change in dacomitinib Cmax and AUC over 0-24 hours after H2RA administra-tion, when compared with those administered dacomitinib alone. Co-administration of an H2RA with dacomitinib is not expected to have any clinically relevant effect on dacomitinib exposure.

pump as turbine (PAT); computational fluid dynamics; variable rotational nominal speed; OpenFoam.

The membrane potential or resting potential of the neuron has been the subject of many studies. Although this theory explains the generation and maintenance of the membrane potential by direct or even facilitated diffusion, there are too many contradictions to doubt that these forces are sufficient or even at work in a process whose initial conditions are of rare complexity. The aim of this article is to show that already in the past, a competing theory has been developed whose hypothesis seems more scientifically sound. To confirm this last theory, Hirohisa Tamagawa carried out an experiment of great simplicity which makes it possible to invalidate the current theory and to question the teaching and the knowledge in Biology and Biophysics.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Following the principles of chemistry, electrostatics and geometry, it becomes clear that ion channels cannot function in this way. The ions channels cannot by their location have both a filter function and be ion concentrators, and the Na/K pump by its position in the membrane and by the proposed assumptions is not able to perform its regulatory function. The current model must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena opening new research perspectives.

Novel molecular pinball machines of the plasma membrane control cytosolic Ca²⁺ levels that regulate plant metabolism. [https://youtu.be/zABg7LiBk88] Essential components involve: 1. an auxin-activated proton pump; 2. arabinogalactan glycoproteins (AGPs); 3. Ca²⁺ channels; 4. auxin-efflux “PIN” proteins. Typical pinball machines release pinballs that trigger various sound and visual effects. However, in plants “proton pinballs” eject Ca²⁺ bound by paired glucuronic acid residues of numerous glycomodules in periplasmic AGP-Ca²⁺. Freed Ca²⁺ ions flow down the electrostatic gradient through open Ca²⁺ channels into the cytosol thus activating numerous Ca²⁺-dependent activities.Clearly cytosolic Ca²⁺ levels depend on activity of the proton pump, the state of Ca²⁺ channels and size of the periplasmic AGP-Ca²⁺ capacitor: Proton pump activation is a major regulatory focal point tightly controlled by the supply of auxin: auxin efflux carriers conveniently known as “PIN” proteins [null mutants are pin-shaped!] pump auxin from cell to cell. Mechanosensitive Ca²⁺ channels and their activation by reactive oxygen species (ROS) are yet another factor regulating cytosolic Ca²⁺.Cell expansion also triggers proton pump/pinball activity by mechanotransduction of wall stress via Hechtian adhesion thus forming a Hechtian oscillator that underlies cycles of wall plasticity and oscillatory growth.Finally, Ca²⁺ homeostasis of plants depends on cell surface external storage as source of dynamic Ca²⁺, unlike the internal ER storage source of animals where the added regulatory complexities ranging from vitamin D to parathormone contrast with the elegant simplicity of plant life. This paper summarises a sixty year Odyssey.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

"Enhancing the Efficiency of Natural Gas Liquid (NGL) Extraction and Fractionation Trains: An Integrated Approach of Simulation Analysis, Advanced Modifications, and Technological Advancements. Through comprehensive research, innovative solutions such as the heat pump aided distillation (HPAD) system and self-heat recuperation technology (SHRT) have been developed to significantly reduce the energy consumption associated with conventional distillation systems. To identify a practical system for NGL fractionation trains, this study extensively examined and compared various HPAD and SHRT options to retrofit a single column. The objective was to find the most suitable and efficient solution for the fractionation process of natural gas liquids (NGLs). The retrofit options analyzed in this study encompassed a range of techniques, including vapor compression (VC), mechanical vapor re-compression (MVR), thermal vapor re-compression (TVR), bottom flashing (BF), side heat exchanger (SHE), intermediate heating and cooling (IHC), self-heat recuperative (SHR), and modified self-heat recuperative (MSHR) distillation. These methods were carefully examined to determine their suitability and effectiveness in improving the performance of NGL fractionation trains In this study, a depropanizer column, typically employed in conventional NGL plants, was selected as a case study. The simulation software Aspen HYSYS V7.3 was employed to model and analyze eight retrofit designs based on predefined criteria. The simulation data was carefully evaluated to identify the most efficient design for minimizing energy consumption. Among the retrofit options, the mechanical vapor re-compression (MVR) technique demonstrated the most significant energy cost reduction, with a remarkable 68.11 percent improvement compared to the base case conventional column. These findings highlight the potential of MVR as an effective solution for lowering energy costs in NGL fractionation trainsFollowing the MVR retrofit option, the study found that vapor compression (VC) achieved a considerable energy cost reduction of 66.65 percent, closely followed by modified self-heat recuperative (MSHR) at 64.02 percent, bottom flashing (BF) at 62.88 percent, self-heat recuperative (SHR) at 55.85 percent, side heat exchanger (SHE) at 54.23 percent, intermediate heating and cooling (IHC) at 39.54 percent, and thermal vapor re-compression (TVR) also at 39.54 percent. These findings highlight the significant potential for energy savings offered by these retrofit options, with VC being the most popular choice, closely followed by MSHR, BF, SHR, SHE, IHC, and TVR.

Small submersible drainage pumps discharge leaking water and rainwater in buildings. In an emergency (e.g., heavy rain or accident), monitoring the flow rate in advance is necessary to enable optimal operation, considering the point where the pump operates abnormally when the water level increases rapidly. In another, pump performance optimization is crucial for energy saving policy. Therefore, it is necessary to meet the challenges of submersible pump systems, including sustainability and pump efficiency. The final goal of this study is to develop an energy-saving, high-efficiency submersible drainage pump capable of responding to emergencies. In particular, this paper targeted the hydraulic performance improvement of a submersible drainage pump model. Before the development of driving mode-related technology capable of emergency response, we first tried to find a way to improve the performance characteristics of the existing submersible drainage pump. Rather than designing a new pump, we disassembled the current pump and reverse engineering. Then, numerical simulation was performed to analyze the flow characteristics and efficiency of the pump. Then, the pump test was carried out to obtain the performance and validated with numerical results. Results revealed that changing the cross-sectional shape of the impeller reduced the flow separation and enhanced velocity and pressure distributions. Also, it reduced the power and increased efficiency. Results also showed that the pump's efficiency increased to 5.56% at a discharge rate of 0.17 m3/min, and overall average efficiency increased to 6.53%. In addition, the submersible pump design method could be suitable for the optimized pump's impeller and casing numerically. This paper can provide insight and information on the design optimization of pumps.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.

Mechanical circulatory support has proven effective in managing postcardiotomy cardiogenic shock by stabilizing patients' hemodynamics and ensuring adequate organ perfusion. Among the available device modalities, the combination of extracorporeal life support and a microaxial flow pump for left ventricular unloading has emerged as a valuable tool in the surgical arma-mentarium. In this publication, we provide recommendations for the application and weaning of temporary mechanical circulatory support in cardiogenic shock patients, derived from a con-sensus among leading cardiac centers in German-speaking countrie