Addition of the bulky redox-active diphosphine 1,8-bis(diphenylphosphino)naphthalene (dppn) to [Fe2(CO)6(-edt)] (1) (edt = 1,2-ethanedithiolate) affords [Fe2(CO)4(2-dppn)(-edt)] (3) as the major product, together with small amounts of a P-C bond cleavage product [Fe2(CO)5{1-PPh2(1-C10H7)}(-edt)] (2). The redox properties of 3 have been examined by cyclic voltammetry and it has been tested as a proton-reduction catalyst. It undergoes a reversible reduction at E1/2 = –2.18 V and exhibits two overlapping reversible oxidations at E1/2 = –0.08 V and E1/2 = 0.04 V. DFT calculations show that while the HOMO is metal-centred (Fe-Fe -bonding), the LUMO is primarily ligand-based but also contains an antibonding Fe-Fe contribution, highlighting the redox-active nature of the diphosphine. It is readily protonated upon addition of strong acids to afford two isomeric hydride complexes and catalyzes the electrochemical reduction of protons at Ep = –2.00 V in the presence of CF3CO2H. The catalytic current indicates that it is one of the most efficient diiron electrocatalysts for the reduction of protons, albeit operating at quite negative potential.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

Fragmentation processes of multiply charged ions of C10H8 isomers produced in fast proton collision (velocity between 1.41 and 2.4 a.u.) is discussed in view of their fundamental molecular dynamics. Especially so in the mechanisms to produce a variety of carbon clusters from such ions. This aspect is assessed with the help of a multihit analysis of daughter ions in coincidence with elimination of H+ and CHn+ (n = 0 to 3). The elimination of H+/C+ was found to be very different from CH3+ loss. The loss of CH3+ was found to be accompanied with the formation of heavy ions like C9H5+, C9H5++ and C7H3+ by a cascade of momentum correlated dissociations. The most probable structures of large fragment ions in the CH3+ loss cascade are predicted with the help of computed electronic energy and the multihit ToF correlations of second and third hit. In addition, we report observation of super-dehydrogenation of naphthalene and azulene targets, with evidence of complete dehydrogenation in a single collision.

Background: to analyze the impact of COVID-19 pandemic on characteristics and management of uveal melanoma (UM) in National Referral Center in Poland. Materials and Methods: the retrospective analysis of 1336 patients who were newly diagnosed with UM at Department of Ophthalmology and Ophthalmic Oncology, Jagiellonian University Collegium Medicum Krakow, Poland between January 1, 2018 and December 31, 2021. The demographic and clinical data were compiled including localization, size and treatment methods of tumors. Results: In total, 728 patients with UM were included before COVID-19 pandemic in years 2018-2019 and 608 were included during COVID-19 pandemic in years 2020-2021. Fixed-base dynamics indicators for the incidence of uveal melanoma (base year 2018) in the national referral center in Poland were 80.22% and 86.81% in year 2020 and 2021, respectively. UMs were statistically significantly larger and more frequently localized anterior to the equator of the eye globe in year 2021 than in year 2018 (Chi^2 Pearson test p= 0.0001 and p= 0.0077, respectively). The rate of patients treated with enucleation increased from 15.94% in year 2018 to 26.90% in year 2021 (Chi^2 Pearson test p=0.0005). Conclusions: statistically significant differences were found in the management of uveal melanoma in National Referral Center in Poland during COVID-19 pandemic with tumors being larger, more frequently localized anterior to the equator of the eye globe and more often enucleated.

In this brief paper we will propose a new equation for the proton charge radius. We will base our new equation on the Trinhammer-Bohr formula which states that the proton charge radius is directly proportional to the proton Compton wavelength. We will then propose a new equation for the proton Compton wavelength which is inversely proportional to the Rydberg constant and directly proportional to the running value of the fine structure constant on the protonic scale. This will define the proton charge radius only by the effective value of the fine structure constant and the Rydberg constant. This new equation also disproves the old value of the proton charge radius 0.877(50) which was measured by using electron-proton scattering and further solidifies the newer and smaller values 0.8414(19) provided by NIST.

Background/Aims: Conflicting results have been reported regarding the interaction between proton pump inhibitors (PPIs) and clopidogrel. We investigated whether concomitant PPI use influenced the risk of recurrence in patients with stroke and myocardial infarction (MI). Methods: This study used two databases for different designs, the Korean National Health Insurance Service (NHIS) database for a self-controlled case series design, and the national sample cohort of the NHIS database converted to the Observational Medical Outcomes Partnership-Common Data Model version for a cohort study. Results: In the PPI co-prescription group, recurrent hospitalization with stroke occurred in 17.6% of the 8,201 patients with history of stroke, and recurrent MI occurred in 17.1% of the 1,216 patients with history of MI during 1 year. According to the self-controlled case series, the overall relative risk (RR) of recurrent stroke was 2.09 [95% confidence interval (CI); 1.83-2.38], and the RR showed an increasing trend with PPI duration. In the cohort study, there was a higher incidence of recurrent stroke in the PPI co-prescription group [Hazard ratio (HR): 1.34, 95% CI: 1.01-1.76, P=0.04]. The overall RR of recurrent MI was 1.47 (95% CI; 1.02-2.11) in the self-controlled case series; however, there was no statistically significant difference in recurrent MI in the cohort study (HR:1.42, 95% CI:0.79-2.49, P=0.23). The impact of individual PPIs on stroke and MI showed different patterns. Conclusions: PPI co-prescription with clopidogrel was associated with recurrent stroke; however, its association with recurrent MI remains inconclusive. The influence of individual PPIs should be clarified in the future.

Since Darwin’s “Power of movement in plants” the precise mechanism of oscillatory plant growth remains elusive. Hence the search continues for the hypothetical growth oscillator that regulates a huge range of growth phenomena ranging from circumnutation to pollen tube tip growth and stomatal movements. Oscillators are essentially simple devices with few components. A universal growth oscillator with only four major components became apparent recently with the discovery of a missing component, notably arabinogalactan glycoproteins (AGPs) that store dynamic Ca2+ at the cell surface. Demonstrably, auxin-activated proton pumps, AGPs, Ca2+ channels and auxin efflux “PIN” proteins, embedded in the plasma membrane, combine to generate cytosolic Ca2+ oscillations that ultimately regulate oscillatory growth: Hechtian adhesion of the plasma membrane to the cell wall and auxin-activated proton pumps trigger the release of dynamic Ca2+ stored in periplasmic AGP monolayers. These four major components represent a molecular PINball machine a strong visual metaphor that also recognizes auxin efflux “PIN” proteins as an essential component. Proton “pinballs” dissociate Ca2+ ions bound by paired glucuronic acid residues of AGP glycomodules, hence reassesses the role of proton pumps. It shifts the prevalent paradigm away from the recalcitrant “acid growth” theory that proposes direct action on cell wall properties, with an alternative explanation that connects proton pumps to Ca2+ signaling with dynamic Ca2+ storage by AGPs, auxin transport by auxin-efflux PIN proteins and Ca2+ channels. The extensive Ca2+ signalling literature of plants ignores arabinogalactan proteins (AGPs). Such scepticism leads us to reconsider the validity of the universal growth oscillator proposed here with some exceptions that involve marine plants and perhaps the most complex stress-test, stomatal regulation.

In this study, we describe quark confinement in terms of linear interaction potentials and solve the problem of the net spin of a proton. The three quarks in a proton are assumed to revolve around a common center, and their masses are determined assuming they are Dirac particles. On the basis of these assumptions, the magnetic moment of a proton can be derived. Moreover, the rotation of the quarks is considered, in which an electrical current induces a magnetic field. Thus, the scalar product of the magnetic moment and field describes the linear interaction potential between the quarks, and the mass of the proton can be obtained. The proton mass predicted by this physical model is consistent with experimental values, and no numerical or fitting calculations are required. Furthermore, using the newly derived spins and angular momentum of the three quarks, we derived the net spin of a proton. Additionally, we predicted the mass of a pi-meson from the same model, which agrees with the experimental values.

Metal organic frameworks (MOFs) are used in catalysis due to their high specific surface area and porous structure. The dispersed active sites and limited reaction space render MOFs have the potential for highly selective electrocatalytic CO2 reduction reaction (ECO2RR). Meanwhile, formic acid (HCOOH) is attracting attention as a liquid product with high economic benefits. This review summarizes the MOFs and their derivatives applied for ECO2RR into HCOOH products. The preparation methods of MOFs as electrocatalysts and their unique advantages are discussed. A series of MOFs, and MOFs derivatives obtained by electrochemical reduction or carbonization processes are highlighted, including metal nanomaterials, carbon-based nanocomposites, single-atom catalysts, and bimetallic nanocomposites. Depending on the MOFs building units (metal ions and organic linkers) and the reaction conditions of derivatization, MOFs-based catalysts exhibit rich diversity and controllable modulation of catalytic performance. Finally, the challenges encountered at this stage and the future research directions of MOFs-based catalysts are proposed.

The improvement of the methane combustion activity was observed in cyclic temperature-programmed and isothermal reactions over Pd/ZrO2 catalysts by simple reduction/re-oxidation treatment. The catalytic activity increased during the initial stages of isothermal reaction, and the light-off temperature was lowered as the number of cycles increased in the cyclic temperature-programmed reaction. To reveal the origin of activation, variations in the reduction properties after the activation period were carefully investigated through CH4 temperature-programmed reduction (TPR) measurements. From the CH4-TPR results, it was confirmed that the reduction temperature decreased significantly after activation. The observation of the CH4-TPR peak at relatively low temperatures is directly proportional to the catalytic activity of CH4 combustion. It was therefore concluded that repeated reduction/re-oxidation occurred in the reactant stream, and this phenomenon allowed the combustion reaction to proceed more easily at lower temperatures.

The cross-kingdom stress hormone abscisic acid (ABA) and its mammalian receptors LANCL1 and LANCL2 regulate cardiomyocyte response to hypoxia by activating NO generation. Over-expression of LANCL1/2 increases transcription, phosphorylation and activity of eNOS and im-proves cell vitality after hypoxia/reoxygenation via the AMPK/PGC-1α axis. The aim of this study was to investigate whether the ABA/LANCL system also affects mitochondrial oxidative metab-olism and structural proteins. The effect of ABA and of the silencing or overexpression of LANCL1 and LANCL2 were investigated in H9c2 rat cardiomyoblasts on mitochondrial function, cell cycle and expression of cytoskeletal, contractile and ion channel proteins. Overexpression or silencing of LANCL1/2 significantly increased, or conversely decreased, mitochondrial number, oxphos complex I, proton gradient, glucose and palmitate-dependent respiration, transcription of uncoupling proteins, expression of proteins involved in cytoskeletal, contractile and electrical functions. These effects, and LANCL1/2-dependent NO generation, are mediated by the tran-scription factor ERRα, upstream of the AMPK/PGC1-α axis and transcriptionally controlled by the LANCL1/2-ABA system. The ABA-LANCL1/2 hormone-receptors system controls fundamental aspects of cardiomyocyte physiology via an ERRα/AMPK/PGC-1α signaling axis and ABA-mediated targeting of this axis could improve cardiac function and resilience to hypoxic and dysmetabolic conditions.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

The measurements of the proton electromagnetic form factors in the time-like region using the initial state radiation technique are reviewed. Recent experimental studies have shown that initial state radiation processes at high luminosity electron-positron colliders can be effectively used to probe the electromagnetic structure of hadrons. The BABAR experiment at the B-factory PEP-II in Stanford and the BESIII experiment at the $\tau$-charm factory BEPC-II in Beijing have measured the time-like form factors of the proton using the initial state radiation process $e^{+}e^{-}\to pbar{p}\gamma$. The two kinematical regions where the photon is emitted from the initial state at small and large polar angles have been investigated. In the first case the photon is in the region not covered by the detector acceptance and is not detected. The Born cross section and the proton effective form factor have been measured over a wide and continuous range of the the momentum transfer squared $q^2$ from threshold up to ~42 (GeV/c)$^2$. The ratio of electric and magnetic form factors of the proton has been also determined. In this report, the theoretical aspect and the experimental studies of the initial state radiation process $e^{+}e^{-}\to p\bar{p}\gamma$ are described. The measurements of the Born cross section and the proton form factors obtained in these analyses near the threshold region and in the relatively large $q^2$ region are examined. The experimental results are compared to the predictions from theory and models. Their impact on our understanding of the nucleon structure is discussed.

36 years after the publication of the important article by Busa and Nuccitelli on the variability of intracellular pH (pH_i) and the interdependence of pH_i and intracellular Ca²⁺ concentration ([Ca²⁺]_i), little research has been carried out on pH_i and calcium signaling. Moreover, the results appear to be contradictory. Some authors claim that the increase in [Ca²⁺]_i is due to a reduction in pH_i, others that it is caused by an increase in pH_i. The reasons for these conflicting results have not yet been discussed and clarified in an exhaustive manner. Variations in pH_i have a significant impact on the increase in [Ca²⁺]_i and hence on some of the basic biochemical mechanisms of calcium signaling. This paper focuses on the possible triggering role of protons, highlighting the mechanisms potentially involved and the open issues that could be clarified by research.

The direct Cr (VI) reduction process by oxalic acid was conducted and the results showed that the Cr (VI) was efficiently reduced by oxalic acid at high reaction temperature and high dosage of oxalic acid. The reduced product, Cr (III), was easily generated stable complex compounds (Cr(HC2O4)3) with oxalate, which displayed a negative effect on the reduction process. The high reaction temperature and high acidic medium could destroy the stable structure of a complex compound to release oxalate, and facilitate the reduction of Cr (VI). Generally, the present study provided a versatile strategy for Cr (VI) reduction, exhibiting a bright application future for real wastewater treatment.

In this paper, we first report that WO_x contained nanoalloys exhibit stable electrocatalytic performance in alkaline media, though bulk WO₃ are easy to be dissolved in NaOH solutions. Carbon supported oxide-rich Pd-W alloy nanoparticles (PdW/C) with different Pd:W atom ratios were prepared by reduction-oxidation method. Among the catalysts, the oxide-rich Pd0.8W0.2/C (Pd/W = 8:2, atom ratio) exhibits the highest catalytic activity for oxygen reduction reaction. The X-ray photoelectron spectroscopy data shows that ~40% of Pd atoms and ~60% of the W atoms are in their oxides form. The Pd 3d_5/2 peaks in oxide-rich Pd-W nanoalloys are positive shift compared with that of Pd/C, which indicates the electronic structure of Pd is affected by the strong interaction between Pd and W/WO₃. Compare to Pd/C, the onset potential of oxygen reduction reaction at the oxide-rich Pd_0.8W_0.2/C is positive shifted. The current density (mA·mg Pd⁻¹) at the oxide-rich Pd_0.8W_0.2/C is ~1.6 times of that at Pd/C. The oxide-rich Pd_0.8W_0.2/C also exhibits higher catalytic stability than Pd/C, which demonstrate that it is a prospective candidate for the cathode of fuel cells operated with alkaline electrolyte.

Proton-pump inhibitors (PPIs) are the most administered first-line treatment for eosinophilic esophagitis (EoE). However, only around half of EoE patients respond histologically to PPI at double dosage. In addition, 70% of responders maintain EoE in remission after tapering the PPI dose. In order to avoid endoscopy with biopsies − the only accurate method of assessing PPI response − efforts have been made to identify PPI responder patients. Clinical or endoscopic features and biomarkers evaluated so far however, have not proved good enough in predicting PPI response. Although new approaches based on omics technologies have uncovered promising biomarkers, the specialized and complex procedures required are difficult to implement in clinical settings. Alternatively, PPI pharmacogenetics based on identifying variations in CYP2C19 and STAT6 genes have shown promising results in EoE, and could easily be performed in most laboratories. Other genetic variations have also been associated with PPI response and may explain those cases not related to CYP2C19 or STAT6. Here, we give an overview of PPI treatment in EoE and evidence of how genetic variations in CYP2C19 and other genes could affect PPI effectiveness, and also discuss studies evaluating the role of pharmacogenetics in predicting PPI response in patients with EoE.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

The evolutionary conserved STING-cGAS pathway represents one of the most important cytosolic DNA sensing systems that is activated in response to viral invasion and/or damaged integrity of the nuclear envelope. The key outcome of this pathway is the production of IFN, which subsequently stimulates hundreds of genes. In oncology, the situation is a complex one since this pathway may serve either anti- or pro-oncogenic roles in a context-dependent fashion. The prevailing understanding is that when the innate immune response is activated by sensing cytosolic DNA, such as from ruptured micronuclei, it results in the production of interferon which attracts cytotoxic cells to destroy tumors. However, in tumor cells that have adjusted to significant chromosomal instability, particularly in relapsed, treatment-resistant cancers, the cGAS–STING pathway often supports cancer progression. In these cells, the pathway initiates a non-canonical nuclear factor κB transcriptional response, fostering the epithelial-to-mesenchymal transition (EMT). Here, we review this intricate pathway in conjunction with cancer progression and development of new treatment modalities.

: This work introduces the instrument design of the medium energy proton detector (MEPD, detection range: 30keV-5MeV) mounted on the Chinese Fengyun-4B (FY-4B) satellite. Compared with the similar detector on the Fengyun-3E (FY-3E) satellite, the instrument has undergone significant changes due to the different orbital radiation environment and solar lighting conditions. Based on the calculation of radiation model AP8, the geometry factor is reduced to 0.002 cm2sr, while the MEPD on FY-3E satellite is 0.005 cm2sr. Another difference is that sensors in some directions is exposed to direct sunlight for 80 minutes every day on this orbit, depending on the attitude angle of the satellite, which is much worse than that on FY-3E satellite. According to the calculation results of permeability of photons through different materials, a 100 nm thickness nickel film is added in front of sensors in order to eliminate light pollution completely. The experiment on the solar simulator shows that the measure is effective and the detector has no error counts when the solar irradiance coefficient is 1.0. In addition, Geant4 software is applied to simulate particle transportation process under complete machine condition so that to check the contamination of electrons on sensors among all directions after magnetic deflection. Data obtained in orbit shows that the instrument works properly, and the data is in good agreement with the AP8 model. The observations of the MEPD on board the FY-4B satellite can provide important support for the safety of the spacecraft and the theoretical research related to space weather.

Purpose: To report the early clinical outcomes of combining intensity‐modulated radiation therapy (IMRT) and intensity‐modulated proton therapy (IMPT) in comparison with IMRT alone in treating the oropharynx cancer (OPC) patients. Materials and Methods: The medical records of 148 OPC patients were retrospectively reviewed, who underwent definitive radiotherapy (RT) with concurrent systemic therapy, from January 2016 till December 2019 at Samsung Medical Center. During the 5.5 weeks’ RT course, the initial 16 (or 18) fractions were delivered by IMRT in all patients, and the subsequent 12 (or 10) fractions were either by IMRT in 81 patients (IMRT only) or by IMPT in 67 (IMRT/IMPT combination), respectively, based on comparison of adaptive re-plan profiles and availability of equipment. Propensity‐score matching (PSM) was done on 76 patients (38 from each group) for comparative analyses. Results: With the median follow‐up of 24.7 months, there was no significant difference in overall survival and progression free survival between groups, both before and after PSM. Before PSM, IMRT/IMPT combination group experienced grade ≥3 acute toxicities less frequently: mucositis in 37.0% and 13.4% (p<0.001); and analgesic quantification algorithm (AQA) in 37.0% and 19.4% (p=0.019), respectively. The same trends were observed after PSM: mucositis in 39.5% and 15.8% (p=0.021); and AQA in 47.4% and 21.1% (p=0.016), respectively. In multivariate logistic regression, grade ≥3 mucositis was significantly less frequent in IMRT/IMPT combination group, both before and after PSM (p=0.027 and 0.024, respectively). AQA score ≥3 was also less frequent in IMRT/IMPT combination group, both before and after PSM (p=0.085 and 0.018, respectively). Conclusions: In treating the OPC patients, with comparable early oncologic outcomes, more favorable acute toxicity profiles were achieved following IMRT/IMPT combination than IMRT alone.

Background: COVID-19 is a disease of the elderly as 95% of deaths related to COVID-19 occur in people over 60 years of age. Despite the urgent need for a preventive treatment there are currently no serious leads, other than the vaccination. Objective: To find a preventive treatment of COVID-19 in elderly patients. Design: Retrospective case-control study. Setting: Robertsau Geriatric Hospital of the University Hospitals of Strasbourg, France. Patients: 179 elderly patients who had been in contact with the SARS-CoV-2, of whom 89 had tested RT-PCR-positive (COVID-pos) for the virus and 90 had tested RT-PCR-negative (COVID-neg). Measurements: Treatments within 15 days prior to RT-PCR (including antihypertensive drugs, antipsychotics, antibiotics, nonsteroidal anti-inflammatory drugs, proton pump inhibitors (PPIs), paracetamol, anticoagulant, oral antidiabetics (OADs), corticosteroids, immunosuppressants), comorbidities, symptoms, laboratory values, and clinical outcome were all collected using the electronic patient record. Results: COVID-pos patients more frequently had a history of diabetes (P=.016) and alcoholism (P=.023), a lower leukocyte count (P=.014) and a higher mortality rate– 29.2% versus 14.4% – (P=.014) when compared to COVID-neg patients. Patients on PPIs were 2.3 times less likely (odds ratio [OR] = 0.4381, 95% confidence interval [CI] [0.2331, 0.8175], P=.0053) to develop COVID-19 infection, compared to those not on PPIs. No other treatment decreased or increased this risk. COVID-19 patients on antipsychotics (P=.0013) and OADs (P=.0166) were less likely to die. Limitations: retrospective study. Conclusion: PPIs treatment lowered the risk of development of COVID-19 infection, and antipsychotics and OADs decreased the risk of mortality in geriatric patients. If further studies confirm this finding, PPIs could be used preventatively in the elderly in this pandemic context. Moreover, OADS and antipsychotics should be tested in clinical trials.

We performed a systematic review and meta-analysis to evaluate the role of gastric acid suppressant use on outcomes of tyrosine kinase inhibitors (TKIs) and oral chemotherapy. We identified all researches evaluating the effect of GAS use on patients receiving oral chemotherapy or TKIs for solid tumors. The pooled hazard ratios (HRs) and 95% confidence interval (95% CI) for overall survival (OS) and progression-free survival (PFS) were calculated with fixed-effects or random-effects model. The study population included n=16 retrospective studies and 372,418 patients. Series concerned gastrointestinal tract tumors (n=5 studies), renal cell carcinomas (RCC, n=3 studies), non-small cell lung cancers (NSCLC, n=5 studies), and soft tissue sarcomas or mixed histologies solid tumors in n=3 studies. The pooled HRs for OS and PFS were 1.31 (95% CI: 1.20–1.43; P<01) and 1.3 (95%CI 1.07-1.57; P<0.01) for GAS and no GAS users, respectively. Only studies of EGFR mutated NSCLC patients receiving TKIs and those with colorectal cancer receiving oral chemotherapy showed a significant correlation between GAS and poor survival. Our study supports the evidence of a possible negative impact of concomitant GAS therapy on survival outcomes of patients receiving oral anti-cancer drugs.

Membranes based on sulfonated synditoactic polystyrene were thoroughly characterized by contrast variation SANS over a wide Q-range in dry and hydrated states. The film samples were prepared by solid-state sulfonation that allowed a uniform sulfonation of only the amorphous phase while preserving the crystallinity of the membrane. The samples were loaded with different guest molecules in either the amorphous (fullerenes) or the crystalline (toluene) regions, in order to vary the neutron contrast or to reproduce the conditions enabling an increased resistance of the membranes to chemical decomposition. The use of uni-axially deformed film samples and contrast variation with different H2O/D2O mixtures allowed for the identification and characterization of different structural levels with sizes between nm and μm, which form and evolve in the membrane morphology in dry and hydrated states and produce scattering features on different detection sectors and at different detection distances after the sample, depending on their size and orientation.

Reversible protonic ceramic cells (rPCCs) combine two different operation regimes, fuel cell and electrolysis cell modes, which allow reversible chemical-to-electrical energy conversion at reduced temperatures with high efficiency and performance. Here we present novel technological and materials science approaches, enabling a rPCC with symmetrical functional electrodes to be prepared using a single sintering step. The response of the cell fabricated on the basis of P–N–BCZD|BCZD|PBN–BCZD (where BCZD = BaCe_0.5Zr_0.3Dy_0.2O_3–δ, PBN = Pr_1.9Ba_0.1NiO_4+δ, P = Pr₂O₃, N = Ni) is studied at different temperatures and water vapor partial pressures (pH₂O) by means of volt-ampere measurements, electrochemical impedance spectroscopy and distribution of relaxation times analyses. The obtained results demonstrate that symmetrical electrodes exhibit classical mixed-ionic/electronic conducting behavior with no hydration capability at 750 °C; therefore, increasing the pH₂O values in both reducing and oxidizing atmospheres leads to some deterioration of their electrochemical activity. At the same time, the electrolytic properties of the BCZD membrane are improved, positively affecting the rPCC’s efficiency. The electrolysis cell mode of the rPCC is found to be more appropriate than the fuel cell mode under highly humidified atmospheres, since its improved performance is determined by the ohmic resistance, which decreases with pH₂O increasing.

The data from social networks like Twitter is a valuable source for research but full of redundancy, making it hard to provide large-scale, self-contained, and small datasets. The data recording is a common problem in social media-based studies and could be standardized. Sadly, this is hardly done. This paper reports on lessons learned from a long-term evaluation study recording the complete public sample of the German and English Twitter stream. It presents a recording solution proposal that merely chunks a linear stream of events to reduce redundancy. If events are observed multiple times within the time-span of a chunk, only the latest observation is written to the chunk. A 10 Gigabyte Twitter raw dataset covering 1,2 Million Tweets of 120.000 users recorded between June and September 2017 was used to analyze expectable compression rates. It turned out that resulting datasets need only between 10\% and 20\% of the original data size without losing any event, metadata or the relationships between single events. This kind of redundancy reduction recording makes it possible to curate large-scale (even nation-wide), self-contained, and small datasets of social networks for research in a standardized and reproducible manner.

Drafting formations have been long recognized as highly effective for reducing drag and enhancing athletic performance, particularly in race walking events. The precise spacing and positioning of the race walkers are critical to optimizing the effectiveness of drafting. In this study, the drag reduction of 15 drafting formations is investigated using wind-tunnel experiments and CFD numerical simulations. The results show excellent consistency in drag reduction rate between the two methods, with differences being within 10%. This can be attributed to spacing replacing body shape differences as the primary factor influencing drag reduction. Optimal double, triple, and quadruple drafting formations produce the same results in both wind-tunnel experiments and CFD simulation, resulting in drag reductions of 67%, 66%, and 81% (wind-tunnel) and 65%, 72%, and 85% (CFD). The sources of drag differences in the two methods are discussed from various aspects. The flow field obtained through CFD analysis is used to examine the mechanism of drag reduction, revealing that drafting formations have a significant shielding effect on incoming air, which reduces the number and speed of airflow impacting the core race walker. This shielding effect is identified as the primary cause of drag reduction. Using an empirical model for mechanical power output, optimal double, triple, and quadruple drafting formations enhance sport economy (4.4-5.7%), speed (3.61-4.67%), and performance (173.8-223.3s) compared to race walking alone. The findings can serve as a reference for race walkers' positioning strategy and provide insights for considering drafting formations in various running events.

We report a detailed investigation of vibrational modes, structure, and dynamics of glutathione (GSH) solutions using ultrasonic relaxation spectroscopy, FT-IR vibrational spectroscopy and electronic absorption measurements. The experimental data were analyzed in view of density functional theory (DFT) and molecular docking calculations. Three distinct Debye-type relaxation processes are resolved in the acoustic spectra, which are assigned to conformational changes between GSH conformers, self-association of GSH, and protonation processes. The standard volume changes for each process were estimated both experimentally and theoretically revealing a close resemblance among them. The higher the effect of the relaxation process in the structure, the greater the induced volume changes. From the temperature dependence of specific acoustic parameters, the thermodynamic characteristics of each process were determined. The experimental FT-IR spectra were compared with the corresponding theoretically predicted vibrational spectra revealing that the GSH dimers and extended conformers dominate the structure of GSH solutions in the high concentration region. The absorption spectra in the ultraviolet region confirmed the gradual aggregation mechanism that takes place in the aqueous GSH solutions. The results of the present study were discussed and analyzed in the framework of the current phenomenological status of the field.

To assess cognitive impairment and affective symptoms and their association with damage to normal-appearing white matter (NAWM) in patients with clinically isolated syndrome (CIS), we compared neuropsychological test scores between patients with CIS and healthy controls, and examined correlations between these and proton magnetic resonance spectroscopy (1H-MRS) outcomes in patients with CIS. Forty patients with CIS and 40 healthy participants were tested with the set of neuropsychological tests, the Beck Depression Inventory (BDI) and the Hospital Anxiety and Depression Scale (HADS). Single-voxel 1H-MRS was performed on frontal and parietal NAWM of patients with CIS to assess ratios of N-acetyl-aspartate (NAA) to creatine (Cr), myo-inositol (mI), and choline (Cho), as well as mI/Cr and Cho/Cr ratios. Patients with CIS had lower cognitive performance, higher scores for the BDI and anxiety subscale of HADS than healthy controls. There were significant correlations between the following neuropsychological tests and metabolic ratios in the frontal NAWM: Stroop Color-Word Test and Cho/Cr, Symbol Digit Modalities Test and mI/Cr as well as NAA/mI, Go/no-go reaction time and NAA/Cho as well as NAA/mI, Californian Verbal Learning Test and NAA/Cr. BDI scores were related to frontal NAA/mI and parietal NAA/Cr and Cho/Cr ratios, whereas HADS-depression scores were associated with frontal NAA/Cr and NAA/mI, and parietal NAA/Cr and Cho/Cr ratios. HADS-anxiety correlated with parietal NAA/Cr ratio. This study suggests that neurochemical changes in the NAWM assessed with single-voxel 1H-MRS are associated with cognitive performance and affective symptoms in patients with CIS.

The current pneumonia epidemic could evolve into a pandemic on a global scale if not effectively contained. The COVID-19 virus possesses a 61-amino acid open reading frame resembling SARS-CoV virulence factor - ORF6 peptide. The isoleucine content is 15.9% in ORF6 of SARS-CoV versus 16.4% of that in SARS-CoV-2. Given the proton affinity in the carbonyl oxygen in isoleucine, augmented proton traffic can enhance proton-ion antiport and prompt cell swelling. Calorie restriction has been confirmed in animal studies to extend lifespan, and its underlying mechanism is not fully known. As the content of essential amino acids in the open reading frame of SARS-CoV-2 reaches 57.4%, a starch/vitamin diet served for short period of time does not give rise to essential amino acids and halts virion production, which could be adopted as prophylactic approach of many viral infections. Plant-based diet or fasting/boiled rice water can also minimize the intake of essential amino acids or all amino acids respectively. Furthermore, several proteins of SARS-CoV-2 possess high valine plus glycine content which is implicated in heart disease, justifying the aforementioned approaches.

The new energy structure needs to balance energy security and dual carbon goals, which has brought major challenges to coal-fired power plants, the pollution reduction and carbon emissions reduction of coal-fired power plants will be a key task in the future. This article proposes an optimization operation of electrostatic precipitators(ESP), based on the working mechanism and historical data of ESP, voltage-current characteristic model and outlet dust concentration prediction model are constructed by deep learning algorithm, Particle Swarm Optimization(PSO) is used to achieve the optimal energy consumption while ensuring stable outlet dust concentration. By training with historical data collected on site, accurate prediction of secondary current and outlet dust concentration of ESP has been achieved, the Mean Absolute Percentage Error(MAPE) of secondary current is less than 1.5%, and the MAPE of outlet dust concentration of ESP on the test set is less than 5.2%. Finally, the optimization experiment is carried out in a 330MW coal-fired power plants, the results showed that the fluctuation of the outlet dust concentration is more stable, and the energy saving is about 43% after optimization, according to the annual operation of 300 days, the annual average carbon reduction is approximately 2621.34 tons. This method is effective and can be applied widely.

The phenomenon of missing data can be seen everywhere in reality. Most typical attribute reduction models are only suitable for complete systems. But for incomplete systems, we can’t obtain the effective reduction rules. Even if there are a few reduction approaches, the classification accuracy of their reduction sets still needs to be improved. In order to overcome these shortcomings, this paper firstly defines the similarities of intra-cluster objects and inter-cluster objects based on the tolerance principle and the mechanism of knowledge granularity. Secondly, attributes are selected on the principle that the similarity of inter-cluster objects is small and the similarity of intra-cluster objects is large, and then the knowledge granularity attribute model is proposed under the background of clustering; Then, the IKAR algorithm program is designed. Finally, a series of comparative experiments about reduction size, running time and classification accuracy are conducted with twelve UCI data sets to evaluate the performance of IKAR algorithms, then the stability of Friedman test and Bonferroni-Dunn test are conducted. The experimental results indicate that the proposed algorithms are efficient and feasible.

Despite providing some critical financial services to support the operation of Emissions Trading Systems (ETS), such as increasing market liquidity and price visibility and allowing operators to hedge against future fluctuations, there is growing concern about the potential threat of financial actors' speculation behaviour to the ETS's effectiveness. To confirm or alleviate the fear associated with such concern, we employ both ex-post and ex-ante approaches to determine the role of speculation in the emission reduction effect of the ETS and its forecasting power in predicting climate change. In addition to confirming carbon prices and the speculation behaviour of the emissions non-compliance actors in the ETS as accurate predictors of climate change, we also show that they both matter in the emission reduction effect of the ETS. We use several verifiable econometric approaches to select the Feasible Quasi Generalised Least Squares (FQGLS) as the best estimator for addressing some of the biases in climate change predictability. We demonstrate that a predictive model combining the complementing dynamics of the EST emissions compliance and emissions non-compliance features forecasts climate change more accurately. We demonstrate the robustness of our findings for both in-sample and out-of-sample forecasts and across different forecast horizons by using alternative approaches to evaluate forecast performance.

In today's society, mankind is confronted with two major problems: the energy crisis and the greenhouse effect. The artificial photosynthesis can use solar energy to convert greenhouse gas CO2 into high-value compounds, which is an ideal solution to alleviate the energy crisis and solve the problem of global warming. The combination of ZnO and polythiophenes (PTh) can make up for each other's drawbacks, thus improving the photoresponse behavior and separation efficiency of photogenerated carriers. PTh layer can transfer photogenerated electrons to ZnO, thereby extending the lifetime of photogenerated charges. The production rate of CH4 from photoreduction of CO2 with ZnO/PTh10 is 4.3 times that of pure ZnO, and the selectivity of CH4 is increased from 70.2% to 92.2%. The conductive PTh can absorb photons to induce π–π* transition, the photogenerated electrons can transfer from LUMO to the conduction band (CB) of ZnO, thus more electrons involve in the reduction of CO2.

Human perception of nature and God have always been inextricably linked. In order to understand nature and its inherent processes, including various natural hazards, the reasons for their origin were often attributed to God's will, suffering for sin and the similar. Fear of material and human losses prompted a man to pray and offer sacrifices/gifts and other rituals to appease the "wrath of the gods". The progress of civilization and technology has not alleviated the destruction and trauma that natural disasters inflict on all aspects of social life. A major obstacle to this is the exponential population growth in vulnerable areas. The frequency of natural disasters and the fatalistic attitudes that limit the effective fight against them have motivated religious communities and individuals to cooperate with international and international organizations and institutions to reduce the risk of local disasters. Believers thus receive the necessary psychological and financial assistance and support from religious communities during all phases of disaster management. Therefore, the subject of this paper is a comprehensive examination relationship between the degree of religiosity of the population and how this connection impacts the policy of reducing disaster risk. The aim of the research is to scientifically describe the nature of the relationship between the degree of religiosity of citizens and different segments of disaster risk reduction.

The validity of our universe as a three-dimensional space (3+1 in relativity) is considered a fundamental fact in physics. In this study, we show that our observed world is thus the output of a prior fundamental operator referred to as an organizer. The organizer is an expansion of projecting operators. It is been shown that identical weighted projecting operators, which are associated with identical particles, generate subspaces of entangled states, whereas groups of unequal weighted coefficients are responsible for finite-size subspaces that are associated with unidentical particles. Considering 3D-subspaces as evidence of the coefficients’ arrangement in our universe, we implement our formalism to describe the implacable vectors, location, momentum, and force within each 3D subspace. By implementing the Heisenberg relation, we drive both the classical and quantum expressions for the laws of motion.

Quantum mechanics introduces the concept of an observer who selects a measuring device and reads the outputs. This measurement process is irreversible. Lately, scholars on quantum collapse phenomena have presented a quantum-like formalism describing the measurement results as an interpretation of the measured object. Note that an observer must read the interpretation results after the interpretation process. Therefore, we propose that the definition of the concept of life should be expanded based on the following concept: A living system decreases entropy, measured results are interpreted, and an internal observer reads the commentary.

This work discussed the advantages of reducing copper in molten copper slag with low S content. FactSage calculated the distribution of copper at equilibrium under different sulfur content. The effect of sulfur content on copper recovery under different oxygen partial pressures was pointed out. The effect of sulfur content on copper recovery in the actual reduction process was explored through experimental research. Under the condition of low sulfur, the Recovery of copper and the stability of the experiment have an ideal results.

The current paper is devoted to the introduction of simpler Eulerian variational principles from which all the relevant equations of non-barotropic stationary magnetohydrodynamics can be derived for magnetic fields which lie on surfaces. A variational principle is given in terms of three independent variables for stationary non-barotropic magnetohydrodynamic flows. This is a smaller number of variables than the eight variables which appear in the standard equations of non-barotropic magnetohydrodynamics which are the magnetic field, the velocity field, the specific entropy and the density. We further investigate the case in which the flow along magnetic lines is not ideal.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Microbe laden air particles, known as bio-aerosols, are routinely generated, in clinical dentistry due to the operative instrumentation within a milieu rich in salivary organisms. As the major mode of transmission of SARS-CoV-2 appears to be airborne aerosols and droplets, there has been an intense focus on such aerosol generating procedures (AGP). As there has been no systematic reviews on the efficacy of bio-aerosol reducing measure in dentistry, the objective of this systematic review was to evaluate the literature on three major AGPs, rubber dam application, pre-procedural oral rinse, and high-volume evacuation (HVE) aimed at reducing dental bio-aerosols. Method: PubMed via Ovid MEDLINE, EBSCO host, Cochrane Library, and Web of Science databases between January 01, 1985, and April 30, 2020, were searched.Results: A total of 156 records in the English language literature were identified, of which 17 clinical studies with 724 patients were included in the final analyses. The eligible reviewed articles revealed the inadequacy of the afore mentioned three principal AGPs used in contemporary dental practice to minimise bio-aerosols. HVE appears to be the most efficacious method, although no single approach provides total elimination of bio-aerosols. Conclusion:This, the first systematic review on methods of controlling bio-aerosols in dental operatory settings, indicates that employing combination strategies of rubber dam, with a pre-procedural antimicrobial oral rinse, and HVE can significantly minimize bio-aerosols. As the quality of the currently available data on dental bio-aerosols are rather poor, further, controlled, multi-centre studies are essential to address this critical issue.

Numerical weather prediction is an initial-value problem, for determination of the initial conditions, there are many methods and one of the most classical methods is variational methods in three dimensions, or 3D-Var. In this approach, with a defined cost function proportional to the square of the distance between the analysis and both the background and the observations, one can obtain the analysis. In the cost function, the background and the observations are reshaped to vectors; within this step, the order of the background error covariance matrix and the observational error covariance matrix becomes huge, which is not convenient to one to obtain the analysis. In this paper, according to the matrix analysis approach, we put forward some possible improvements to the dimension-reduction algorithm of 3D-Var, so that provide some references for data assimilation.

Replacing carbon by hydrogen is a huge step towards reducing CO₂ emissions in the iron- and steel-making industry. The reduction of iron oxides using hydrogen plasma smelting reduction as an alternative to conventional steel-making routes has been studied at Montanuniversitaet Leoben, Austria. The aim of this work was to study the slag formation during the reduction process and the reduction behaviour of iron oxides. Furthermore, the reduction behaviour of iron ore during continuous feeding was assessed. Mixtures of iron ore and calcined lime with a basicity of 0, 0.8, 1.6, 2.3, and 2.9 were melted and reduced by hydrogen. The off-gas composition was measured during the operations to calculate the process parameters. The reduction parameters, namely the degree of reduction, degree of hydrogen utilisation, produced iron, and slag, are presented. The results of the batch-charged experiments showed that at the beginning of the reduction process, the degree of hydrogen utilisation was high, and then, it decreased over the operation time. In contrast, during the continuous-feeding experiment, the degree of hydrogen utilisation could be kept approximately constant. The highest degrees of reduction and hydrogen utilisation were obtained upon the application of a slag with a basicity of 2.3. The experiment showed that upon the continuous feeding of iron ore, the best conditions for the reduction process using hydrogen could be applied.

Objective: We report a case of acute pancytopenia and liver injury after concomitant administration of low-dose methotrexate (MTX), and high-dose esomeprazole and metamizole. Case summary: A 71-year-old patient with chronic systemic idiopathic erosive arthritis was admitted after a pelvic ring fracture. After hospital admission, she received MTX in addition to esomeprazole and metamizole. Subsequent laboratory tests revealed pancytopenia and elevated liver enzymes. The follow-up clinical examinations were unremarkable, with the exception of sub-febrile temperatures. Further investigations did not detect a definitive etiology. Due to the suspicion of methotrexate-induced hematotoxicity and hepatotoxicity, antagonizing therapy with calcium folinate was administered, after which the blood counts and liver parameters normalized. Discussion: Due to the administration of high-dose metamizole immediately before the administration of low-dose MTX, the pre-existing hematotoxic pharmacodynamic effect of MTX was acutely enhanced by that of metamizole, although folic acid was administered preemptively. In addition, the concomitant administration of high-dose esomeprazole and normal dose torasemide resulted in a pharmacokinetic interaction with MTX by decreasing its renal secretion and elimination, further enhancing the concentration-dependent hematotoxic and hepatotoxic side effects of MTX. Conclusions: The relatively high demand for analgesics in patients with chronic rheumatic diseases already being treated with MTX and proton pump inhibitors necessitates that clinicians consider drug-drug interactions as potential causes of adverse drug reactions after the administration of metamizole or nonsteroidal anti-inflammatory drugs. In this category of patients, it is strongly recommended to switch to analgesics of other classes.

We conducted this systematic review with the objective to understand the efficacy and safety of proton pump inhibitors [PPIs] in the pediatric population. We have used PubMed to identify randomized controlled trials [RCTs] published between 1st June 2010 and 30th June 2023, in patients from birth to 18 years old, with gastroesophageal reflux disease [GERD], who received treatment with any PPI. The literature yielded 76 articles and 13 met inclusion criteria. For infants, PPIs were equal to placebo in reducing GERD symptoms in 4 articles. In 1, the number of GER episodes and esophageal acid exposure were lower in infants who received PPIs and left lateral position, but there was no significant improvement in symptoms. In another publication, the combination of PPIs and feeding modifications [FM] was not more effective than PPIs alone. For children and adolescents, PPIs were effective in improving symptoms and achieving mucosal and histological healing, which was subsequently maintained. To conclude, PPIs are not effective to reduce symptoms related to GERD in infants, but are effective in older children, along with histological remission. Generally, PPIs are well tolerated, but it is important to not forget the possible adverse events [AE], especially if they are used for a long time.

Dacomitinib is an irreversible epidermal growth factor receptor (EGFR) tyrosine kinase inhibitor indicated for the treatment of patients with advanced non-small cell lung cancer (NSCLC) and EGFR-activating mutations. Proton pump inhibitors decreased dacomitinib exposure. This anal-ysis summarizes the effect of H2RA on dacomitinib exposure. A within-patient comparison of steady-state trough concentrations (Ctrough,ss) of dacomitinib and its active metabolite and active moiety with and without concomitant use of H2RA was conducted using a linear mixed effects model with pooled data from 11 clinical studies in patients with NSCLC. An oral absorption PBPK model was constructed and verified using clinical PK data after a single dose of dacomitinib in healthy volunteers to estimate the effect of gastric pH altered by an H2RA on dacomitinib PK. The adjusted geometric mean of dacomitinib Ctrough,ss of dacomitinib parent, metabolite and active moiety following co-administration with H2RA was approximately 86%, 104% and 100% relative to that following dacomitinib 45 mg administration without H2RA (P>0.05). The PBPK modeling showed negligible change in dacomitinib Cmax and AUC over 0-24 hours after H2RA administra-tion, when compared with those administered dacomitinib alone. Co-administration of an H2RA with dacomitinib is not expected to have any clinically relevant effect on dacomitinib exposure.

Recent advancements in the study of the protein complex photosystem II have clarified the sequence of events leading to the formation of oxygen during the S3->S4->S0 tran-sition, wherein the inorganic Mn4Ca(µ-O)6(OHx)4 cluster finishes photo-catalyzing the water splitting reaction (Greife et al, Nature 2023, 617, 623-628; Bhowmick et al, Nature 2023, 617, 629-636) . During this final step a tyrosine radical (TyrZ), stable for a couple of milliseconds, oxidizes a cluster bound oxygen while the hydrogen bonding patterns of nearby waters shift a proton away. A treatment of this redox reaction within the context of accepted transition state theories predicts rate constants that are significantly higher than experimentally recovered values (10^12s^-1 versus 10^3s^-1). In an effort to understand this disparity, temperature dependent experiments have revealed large entropic con-tributions to the rates with only a moderate energy of activation. We suggest that the entropic source may be related to the observed proton rearrangements, and further possible near isoenergetic variations in the nearby extended h-bonding network de-laying the realization of an ‘ideal’ transition state. In the following we explore this re-lation in the context of Eyring’s transition state theory and Marcus’ electron transfer theory, and evaluate their compatibility with the experimental evidence.

Novel molecular pinball machines of the plasma membrane control cytosolic Ca²⁺ levels that regulate plant metabolism. [https://youtu.be/zABg7LiBk88] Essential components involve: 1. an auxin-activated proton pump; 2. arabinogalactan glycoproteins (AGPs); 3. Ca²⁺ channels; 4. auxin-efflux “PIN” proteins. Typical pinball machines release pinballs that trigger various sound and visual effects. However, in plants “proton pinballs” eject Ca²⁺ bound by paired glucuronic acid residues of numerous glycomodules in periplasmic AGP-Ca²⁺. Freed Ca²⁺ ions flow down the electrostatic gradient through open Ca²⁺ channels into the cytosol thus activating numerous Ca²⁺-dependent activities.Clearly cytosolic Ca²⁺ levels depend on activity of the proton pump, the state of Ca²⁺ channels and size of the periplasmic AGP-Ca²⁺ capacitor: Proton pump activation is a major regulatory focal point tightly controlled by the supply of auxin: auxin efflux carriers conveniently known as “PIN” proteins [null mutants are pin-shaped!] pump auxin from cell to cell. Mechanosensitive Ca²⁺ channels and their activation by reactive oxygen species (ROS) are yet another factor regulating cytosolic Ca²⁺.Cell expansion also triggers proton pump/pinball activity by mechanotransduction of wall stress via Hechtian adhesion thus forming a Hechtian oscillator that underlies cycles of wall plasticity and oscillatory growth.Finally, Ca²⁺ homeostasis of plants depends on cell surface external storage as source of dynamic Ca²⁺, unlike the internal ER storage source of animals where the added regulatory complexities ranging from vitamin D to parathormone contrast with the elegant simplicity of plant life. This paper summarises a sixty year Odyssey.

Understanding the ionic channel network of proton exchange membranes, which dictate fuel cell performance, is crucial when developing proton exchange membrane fuel cells. However, itis difficult to characterize due to complicated nano structure and differing changes to their structure with different amounts of water uptake. Electrostatic force microscopy (EFM) can map surface charge distribution as nano special resolution by measuring the electrostatic force between a vibrating conductive tip and a charged surface under an applied voltage, . In this study, the ionic channel network of a proton exchange membrane is analyzed using EFM. A mathematical approximation model of the ionic channel network is first derived, to explain changes in force gradient on the surface using EFM. The phase lag of dry and wet Nafion under stepwise changes to bias voltage is then measured. Based on the model, variations in the ionic channel network of Nafion with different amounts of water uptake are analyzed numerically. The mean surface charge density of both membranes, which is connected with the ionic channel network, is calculated using the model. The results show that the difference between the mean surface charge of the dry and wet membranes is consistent with the variation in their proton conductivity.

Molecular overtone transitions provide optical frequency transitions sensitive to variation in the proton-to-electron mass ratio (μ = m_p/m_e). However, robust molecular state preparation presents a challenge critical for achieving high precision. Here, we characterize infrared and optical-frequency broadband laser cooling schemes for TeH⁺, a species with multiple electronic transitions amenable to sustained laser control. Using rate equations to simulate laser cooling population dynamics, we estimate the fractional sensitivity to μ attainable using TeH⁺. We find that laser cooling of TeH⁺ can lead to significant improvements on current μ variation limits.

The development of hydrogen plasma smelting reduction as a CO₂ emission-free steel-making process is a promising approach. This study presents a concept of the reduction of hematite using hydrogen thermal plasma. A laboratory scale and pilot scale hydrogen plasma smelting reduction (HPSR) process are introduced. To assess the reduction behavior of hematite, a series of experiments has been conducted and the main parameters of the reduction behavior, namely the degree of hydrogen utilization, degree of reduction and the reduction rate are discussed. The thermodynamic aspect of the hematite reduction is considered and the pertinent calculations have been carried out using FactSage^TM 7.2. The degree of hydrogen utilization and the degree of reduction were calculated using the off-gas chemical composition. The contribution of carbon, introduced from the graphite electrode, ignition pin and steel crucible, to the reduction reactions was studied. The degree of reduction of hematite, regarding H₂O, CO and CO₂ as the gaseous reduction products, is determined. It is shown that the degree of hydrogen utilization and the reduction rate were high at the beginning of the experiments, then decreased during the reduction process owing to the diminishing of iron oxide. Conducting experiments with the high basicity of slag B₂=2 led to a decrease of the phosphorus concentration in the produced iron.

Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

Energy demand has exponentially increased with the increase in the world population and ur-banization. Renewable energy is clean, renewable, and environmentally friendly. Hydrogen production through Proton Exchange Membrane (PEM) electrolyzer is an efficient way to produce renewable energy. The efficiency and energy consumption of the PEM electrolyzer depends on the feed water quality. In this report, we study the effect of pH, TDS, and conductivity on hydrogen production as well as energy consumption during the process. pH values (3, 7, 9), TDS values (300ppm, 600ppm, 900ppm), and conductivity values (30mS/cm, 70mS/cm, 100mS/cm) were studied to understand and optimize the hydrogen production using PEM electrolyzer. The in-vestigations showed that hydrogen production is significantly affected by pH, total dissolved solids, and conductivity, and the best levels of each variable were identified by extensive testing. The findings show both the scientific significance of proton exchange electrolysis in meeting the growing energy demands of society as well as the importance of knowing the influence that di-verse conditions have on the creation of hydrogen. Our research, in general, contributes to the expanding body of scientific knowledge on the topic of the effective production of hydrogen and offers useful insights for the continuation of investigation in this field.

We have developed IrO_x/M-SnO₂ (M = Nb, Ta, and Sb) anode catalysts, IrO_x nanoparticles uniformly dispersed on M-SnO₂ supports with fused-aggregate structures, which make it possible to evolve oxygen efficiently, even with a reduced amount of noble metal (Ir) in proton exchange membrane water electrolysis. Polarization properties of IrO_x/M-SnO₂ catalysts for the oxygen evolution reaction (OER) were examined at 80 °C in both 0.1 M HClO₄ solution (half cell) and a single cell with a Nafion^® membrane (thickness = 50 μm). While all catalysts exhibited similar OER activities in the half cell, the cell potential (E_cell) of the single cell was found to decrease with the increasing apparent conductivities (σ_{app, catalyst}) of these catalysts: an E_cell of 1.61 V (voltage efficiency of 92%) at 1 A cm^-2 was achieved in a single cell by the use of an IrO_x/Sb-SnO₂ anode (highest σ_{app, catalyst}) with a low Ir-metal loading of 0.11 mg_Ir cm^-2 and Pt supported on graphitized carbon black (Pt/GCB) as the cathode, with 0.35 mg_Pt cm⁻². In addition to the reduction of the ohmic loss in the anode catalyst layer, the increased electronic conductivity contributed to decreasing the OER overpotential due to the effective utilization of the IrO_x nanocatalysts on the M-SnO₂ supports, which is an essential factor in improving the performance with low noble metal loadings.

Breast cancer is the most prevalent malignancy among women globally. Early diagnosis and treatment improvements are leading to a growing population of survivors. This has increased the risk of developing contralateral breast cancer (CBC), a distinct occurrence in the opposite breast of a previously diagnosed patient. The treatment options for breast cancer are often mas-tectomy or lumpectomy. Patients with lumpectomy frequently undergo a contralateral reduc-tion procedure to achieve more symmetry after the primary breast cancer surgery. The reduc-tion specimen is usually routinely examined by pathology to check for malignancies. The exci-sion in pieces and the absence of specific markers or ink make an examination of tumor size and margin status more challenging, impacting treatment decisions. A new protocol introduced in July 2022 seeks to improve diagnostic precision and treatment planning by excision in toto, marking, and inking excised reduction tissue to examine and treat potential CBC more effectively.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

Parametric models have been widely used in pertinent literature for reconstructing, modifying and representing a wide range of airfoil and/or hydrofoil profile geometries. Design spaces corresponding to these models can be exploited for modeling and profile-shape optimization under various performance criteria. Accuracy requirements, along with the need for modeling local features, often lead to high-dimensional design spaces that hinder the process of shape optimization and design through analysis. In this work, we propose a shape-informed dimensional reduction approach that attempts to tackle this deficiency by producing low-dimensional latent design spaces that can be efficiently used in shape representation and optimization. Furthermore, geometric moments are introduced in an attempt to cost-effectively capture analysis-relevant information that is generally expensive to produce. Specifically, geometric integral properties, although intrinsic features of the shape, are quite commonly related to performance indicators employed in performance optimization and therefore provide a cost-effective physics-informed component in the description of the design in the latent space. To this end, we employ the generalized Karhunen-Loeve expansion to produce a shape- and physics-informed subspace retaining the highest possible geometric variance and robustness, that is, lack of invalid designs. At the same time, a series of shape discretizations, encoding the foil's shape profile, are examined with regards to their effect on the resulting latent space's quality and efficiency. Our results demonstrate a significant reduction in the dimensionality of the original design space while maintaining a high representational capacity and a large percentage of valid geometries that facilitate fast convergence to optimal solutions in performance-based optimization.

Emerging infectious disease threats are becoming more frequent due to various social, political and geographical pressures including increased human-animal contact, global trade, transportation and changing climate conditions. As a result, the threat that emerging agents can be spread by blood contact or transfusion of blood products also becomes increasingly problematic. Blood transfusion is essential in treating patients with anemia, blood loss, and other medical conditions. However, these lifesaving components can become a vector for spreading diseases, particularly to vulnerable populations. New methods have been implemented on a global basis for prevention of transfusion transmission via plasma, platelet, and whole blood products. Implementing proactive pathogen reduction methods can significantly reduce the likelihood of disease transmission via blood transfusion, even for newly emerging agents whose transmissibility and susceptibility are still being evaluated as they emerge. In this review, we consider the Mirasol PRT system for blood safety which is based on a photochemical method involving Riboflavin and UV light. We provide examples of how emerging threats such as Ebola, SARS-CoV-2, Hepatitis E, monkeypox and other agents have been evaluated in real time regarding effectiveness of this method for reducing the likelihood of disease transmission via transfusion. Keywords: transfusion; blood; pathogen reduction; emerging infectious diseases.

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

Given a polynomial $P(x_{1}, x_{2}, \ldots, x_{n})$ which is the sum of terms, where each term is a product of two distinct variables, then the problem $APSS$ consists in calculating the total sum value of $\sum_{\forall U_{i}} P(u_{1}, u_{2}, \ldots, u_{n})$, for all the possible assignments $U_{i} = \{u_{1}, u_{2}, ... u_{n}\}$ to the variables such that $u_{j} \in \{0, 1\}$. $APSS$ is the abbreviation for the problem name Algebraic Polynomial Sum Solver Over $\{0, 1\}$. We show that $APSS$ is in $\#L$ and therefore, it is in $FP$ as well. The functional polynomial time solution was implemented with Scala in \url{https://github.com/frankvegadelgado/sat} using the DIMACS format for the formulas in $\textit{MONOTONE-2SAT}$.

Abstract: The paper defines the characteristics of two proto-quark stars (M_b=1.22M_? and M_b=1.62M_(?"\ " )) that were formed after the explosion of the supernova. It is assumed that the changes in the energy and lepton charge of the central regions of the pre-supernova star can be neglected during the implosion. The equation of state for hot quark matter is determined based on the MIT bag theory taking into account the presence of neutrinos. The possible maximum values of the central temperatures of these stars are determined. The energy of neutrinos in the studied proto-quark stars is of the order of 250-300 MeV. The decrease in the mass of these stars during cooling is about 0.16 for M_b=1.22M_? and 0.25 for M_b=1.62M_(?"\ " ).

Background: Twitter is a major tool for communication in emergencies such as natural disasters. This online social network allows the user to produce content, and it is not designed exclusively for news releases, as opposed to other service providers. Aim: The aim of this study is to investigate Twitter uses in natural disasters and pandemics. Methods: The included studies reported the role of Twitter in natural disasters. The studies that report in settings other than the natural disasters (such as man-made disasters) and other social media were excluded. Electronic databases for a comprehensive literature search including MEDLINE, Web of Science, CINAHL, PsycINFO, Cochrane Register of Controlled Trials (CENTRAL) and EMBASE were used to identify the records that match the mentioned inclusion criteria published till May 2020. The study characteristics were extracted from the qualified studies including year of publication, findings, and geographical location of the study conduct. A narrative synthesis for this literature review was used. Results: The search identified 822 articles of which 780 articles were removed, 256 were not available, 311 papers were not relevant, 16 were duplicated articles, and 197 were non-related to the emergencies. 45 articles met the selection criteria and were included in the review. eleven themes were found in the narrative synthesis including early warning, disseminating information and misinformation, advocacy, personal gains, assessment, various roles of organizations, public mood, geographical analysis, charity, using influencers, and trust. Conclusions: It is recommended that influential individuals be identified in each country and community before disasters occur so that the necessary information can be disseminated in response to disasters. Preventing the spread of misinformation is one of the most important issues in times of disaster, especially pandemics. Disseminating accurate, transparent, and prompt information from relief organizations and governments can help. Also, analyzing Twitter data can be a good source for understanding the mental state of the community, estimating the number of injured people, estimating the points affected by natural disasters, and modeling the prevalence of epidemics. Therefore, various groups such as politicians, the government, non-governmental organizations, aid workers, and the health system can use this information to plan and implement interventions.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.

Changes in the amount and the distribution of mean and turbulent quantities in the free shear layer wake of a 2D NACA 0012 airfoil and AR 4 NACA 0012 wing with passive segmented rigid trailing edge (TE) extensions was investigated at the University of Dayton Low Speed Wind Tunnel (UD-LSWT). The TE extensions were intentionally placed at zero degrees with respect to the chord line to study the effects of segmented extensions without changing the effective angle of attack. Force based experiments was used to determine the total lift coefficient variation of hte wing with seven segmented trailing edge extensions distributed across the span. The segmented trailing edge extensions had negligible effect of lift coefficient but showed measurable decrement in sectional and total drag coefficient. Investigation of turbulent quantities (obtained through Particle Image Velocimetry (PIV)) such as Reynolds stress, streamwise and transverse RMS in the wake, reveal a significant decrease in magnitude when compared to the baseline. The decrease in the magnitude of turbulent parameters was supported by the changes in coherent structures obtained through two-point correlations. Apart from the reduction in drag, the lower turbulent wake generated by the extensions has implications in reducing structural vibrations and acoustic tones.

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Jakarta belongs to the cities with the highest flood risk in the world. Its flood hazard is driven by land subsidence, soil sealing, changes in river discharge and increasingly sea level rise. As all of these trends are set to continue, Jakarta’s flood hazard is expected to intensify in the future. Designing and implementing risk reduction and adaption measures is therefore of utmost importance. Against the background, the paper draws on a discourse analysis and original empirical household survey data to review and evaluate current adaptation measures and to analyze in how far they describe a path that is transformative from previous risk reduction approaches. The results show that the focus is clearly on engineering solutions, foremost in the Giant Sea Wall project. The project is likely to transform the city’s flood hydrology. However, it cements rather than transforms the current risk management paradigm which gravitates around the goal of controlling flood symptoms, rather than addressing their anthropogenic root causes. The results also show that the planned measures are heavily contested due to concerns about ecological impacts, social costs, distributional justice, public participation and long-term effectiveness. On the outlook, the results therefore suggest that the more the flood hazard will intensify in the future, the deeper a societal debate will be needed about the desired pathway in flood risk reduction and overall development planning – particularly with regards to the accepted level of transformation, such as partial retreat from the most flood-affected areas.

Nickel molybdate, NiMoO₄, nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using UV-Vis absorption.

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

Accurate and efficient determination of excited-state polarizabilities (α) is an open problem both experimentally and computationally. Following our previous work, [Phys. Chem. Chem. Phys. 2023, 25, 2131−2141], where one can employ simple ground-state density-based functions from the information-theoretic approach (ITA) to accurately and efficiently predict the macromolecular polarizabilities, we aim to predict the lowest excited-state polarizabilities in this work. The philosophy is to use density-based functions to depict the excited-state polarizabilities. As a proof-of-principle application, employing 2-(2′-hydroxyphenyl)benzimidazole and its derivatives as model systems, we have verified that either with the ground-state (S0) or excited-state (S1) densities as input, ITA quantities can be strongly correlated with the excited-state polarizabilities. When the transition densities are considered, both S0 and S1 polarizabilities are in good relationships with some ITA quantities. Furthermore, excitation and emission energies can be predicted based on multivariant linear regression equations of ITA quantities.

At present there is a renewed interest in theories of ”modified” gravity. Here, under a more drastic modification enforced by Galilei group, we obtain a completely new gravitational structure, and which exists in addition to the already available general relativity of today. Correlated with this, we show that in addition, there is a new ”modified” quantum mechanics, in as much as it exists as an independent and new ”pure” non-relativistic quantum me- chanics, and which has no relativistic counterpart. This is in addition to the present quantum mechanics, where the relativistic and non-relativistic structures are counterparts of each other. The above holds, firstly due to the correlation between Galilei group and quantum mechanics. These math- ematical conclusions are consolidated by the fact that there exists a physical Majorana interaction between each neutron- proton pairs in nuclei. Galilei invariance of Majorana exchange in Majorana interaction, shows that the mass here is of pure gravitational nature, and which is immune to the other three forces. This makes an amazing connection between the gravitational force and the quantum mechanics. This pure gravitational mass would man- ifest itself as dark matter of the universe. It is our new modified gravity that generates the dark matter.

The genome of Vibrio cholerae contains three structural genes for the NhaP-type cation-proton antiporter paralogues, Vc-NhaP1, 2 and 3 mediating exchange of K+ and or Na+ for protons across the membrane. Based on phenotype analysis of chromosomal Vc-NhaP1, 2 and 3 triple deletion mutants we suggested that Vc-NhaP paralogues might play a role in the Acid Tolerance Response (ATR) of V. cholerae as it passes through the gastric acid barrier of the stomach. Comparison of the biochemical properties of Vc-NhaP isoforms revealed that Vc-NhaP2 is the most active among all three paralogues. Therefore, Vc-NhaP2 antiporter is a plausible therapeutic target for developing novel inhibitors targeting these ion exchangers. Our structural and mutational analysis of Vc-NhaP2 identified a putative cation binding pocket formed by antiparallel extended regions of two transmembrane segments (TMSs V/XII) along with TMS VI. Molecular Dynamics (MD) simulations suggested that the flexibility of TMS-V/XII is crucial for the intra-molecular conformational events in Vc-NhaP2. In this study, we developed some putative Vc-NhaP2 inhibitors from Amiloride analogs (AAs). Amiloride is a potent inhibitor of human Na+/H+ exchanger-1 (NHE1). Based on the pharmacokinetic properties and potential binding affinity scores we chose six AAs showing high binding affinity scores to Vc-NhaP2. In silico, the six AAs interacted with the functionally important amino acid residues located in TMSs III, IV, V, VI, VIIII and IX either from the cytoplasmic side (three AAs) or the periplasmic side (three AAs) of Vc-NhaP2. Four AAs were modified to reduce their toxicity profile compared to the original AAs. Molecular docking of the modified AAs revealed promising binding. The four selected drugs interacted with functionally important amino acid residues located on the cytoplasmic side of TMS VI, the extended chain region of TMS V and TMS XII and the loop region between TMSs VIIII and IX. Molecular dynamics simulations revealed that binding of the selected drugs destabilized the Vc-NhaP2 and altered the flexibility of functionally important TMS VI.

Protein is the proteios building block of life. Evolutionarily, its sequence is not as conserved as its structure, making it more reasonable for protein structure, instead of protein sequence, to be the descriptor of protein function. Yet, in the National Center for Biotechnology Information (NCBI) database, the number of experimentally identified protein sequences is in great excess of that of experimentally determined protein structures inside the almost-half-a-century old Protein Data Bank (PDB). For instance, GPR151 is an proton-sensing G-protein coupled receptor (GPCR) originally identified as homologous to galanin receptors. As of March 19, 2020, GPR151’s structure has not been experimentally determined and deposited in PDB yet. Thus, an ab initio modelling approach was employed here to build a three-dimensional structure of GPR151. Overall, the ab initio GPR151 model presented herein constitutes the first structural hypothesis of GPR151 to be experimentally tested in future with previously published, currently ongoing and future GPR151 studies.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

The use of hyperthermia is one of the effective methods of treating cancer. In this case, the problem arises of constructing and predicting the distribution of the thermal field inside tissues depending on their type. This paper discusses the use of linear and polynomial regression methods, as well as regression algorithms based on decision tree, random forest and K nearest neighbors methods to recover missing temperature values. The influence of the size of the training sample when performing regression on the quality of the reconstructed values is investigated. Experimental recommendations on sample size are given for the selected decision tree and random forest methods. The possibility of a significant (10 times or more) reduction in the initial sample size, without leading to a decrease in the R² metric by more than 0.05 for various tissues, has been shown.

Background and objectives: Thoracolumbar fracture – dislocations (AO type C) are rare injuries that occur due to very high-energy trauma, and the result is transitional and rotational instability of the spinal column and neurological impairment. Several reduction maneuvers have thus far been published, each of which can be of use in certain specific situations. We developed a novel modification to the previously described reduction technique. Materials and methods: This is a retrospective review of the management of thoracic AO type C fracture-dislocations managed with a modified novel reduction technique. The success of the reduction and intraoperative iatro-genic complications such as dural tear and screw pull out were the outcomes analyzed. Results: A total of 4 cases were successfully reduced with this novel reduction technique. We did not note any complications such as a dural tear or screw failure with this modified novel reduction tech-nique. Conclusion: The novel modification to the reduction technique employed in the management of thoracic fracture-dislocations resulted in a successful reduction without the risk of iatrogenic complications due to the reduction maneuver.

This study aimed to investigate the effect of reducing the amount of organic waste on the weight of cats in Tehran. The weight of 4192 cats was measured from spring 2016 to the end of winter 2020. They were classified into 6 age groups, 2 gender groups, and 13 geographical areas. Their weight was measured for 48 months (16 seasons). The statistical parameters analysis showed no weight loss in 2017, but since 2018, cats have been losing weight every year. They had lost about 178g of their weight in 2018. The sharpest annual decrease was observed in 2019 when about 301g of weight loss was recorded. In the winter of 2020, 115g of weight loss took place. In the spring of 2017, no weight change was observed, but in the spring of 2018, the cats lost 155g of their weight. Their weight loss intensified in the spring of 2019 and about 299g of weight loss was observed. In the summer of 2017, as in the spring of the same year, no weight loss was recorded, but for the summer of 2018, the weight loss was evident and about 205g of the weight of the cats had been reduced. The weight loss in the summer of 2019 not only continued but intensified and about 304g of weight loss was recorded for cats. Weight change was not observed in the fall of 2017 as in the spring and summer of the same year. In the fall of 2018, weight loss was recorded for cats. They had lost about 324g of their weight in the fall of 2018. Also, they experienced a weight loss of about 218g in the fall of 2019. During the spring, summer, and autumn of 2017, no weight loss was observed in the cats for the winter of 2018, but in the winter of 2019, the cats faced the most severe weight loss (seasonally). They lost about 401g of weight in the winter of 2019. Of course, in the winter of 2020, about 186g of weight loss was observed in cats. The results showed that female cats did not lose weight in 2017 but experienced weight loss in 2018 with a weight loss of 181g. The weight loss of females intensified in 2019 and 294g of weight loss was recorded. Female cats lost 186g of their weight in the winter of 2020. Male cats did not lose weight like female cats in 2017. But in 2018, a weight loss of 166g was observed in male cats. The weight loss of male cats continued in 2019 and 311g of weight loss was recorded for them. However, in 2020, unlike females, weight loss was not observed in male cats. It can be said that both sexes lost more weight in the winter of 2019 than in other seasons. In 2017, weight loss was observed only for the region of 10, and in the same year, weight gain was recorded for the region of 15. But in 2018, except for regions 3, 4, 15, and 19, weight loss was observed in other regions. In 2019, the weight loss of cats spread and weight loss was observed in all regions except the region of 12. In winter 2020, weight loss was recorded only in the region of 4. In the end, it can be concluded that the weight of cats has decreased since the spring of 2018 because the beginning of the decrease in the amount of organic waste has been recorded since the winter of 2018. So, there is a direct relationship between the weight of cats and the amount of organic waste (access to food). The amount of garbage has been decreasing since the winter of 2018, and the average weight of cats has also been decreasing since the spring of 2018 due to the decrease in access to food.

This study investigated the development of Aedes aegypti density in houses of the urban locality of Poblado Miguel Alemán Valdes, in the Sonora state of Mexico, after application of 1% propoxur paint as full wall coverage (IP) and targeted indoor painting (IP 1m) in comparison to IRS with propoxur 70% WP (full wall coverage). The 1% propoxur paint was applied by the homeowners by brushing and rolling at the recommended dose of 1L/8 m², equivalent to 1.5 g a.i./m², while IRS was conducted by professionals with Propoxur 70% WP at a dose of 1 g a.i./m². Adult mosquito surveys were conducted in a random sample of houses in each block one week before the interventions and at week 1, month 1 to 4, month 6, month 9 and month 12 post-interventions. All three propoxur based treatments provided similar reductions (43.7%, 44.9% and 41.3% for IP, IP 1m and IRS respectively) in the fraction of houses positive in female Aedes aegypti resting indoor and outdoor as one year average of 8 follow up surveys. Indoor resting density of Aedes females during the one-year evaluation was reduced by 77.5% through IP followed by IP 1m with 64.2% reduction and 30% reduction with IRS. Culex mosquitoes’ interior density was affected as well by the insecticide treatments with similar average reductions for IP 1m (50.0%) and IRS (57.8%) in comparison with control. Aedes breeding was impacted by the insecticide paint in similar extent for both interventions, expressed by a substantial reduction of the House Index (20.1% IP, 31.2% IP 1m) and especially the Container Index (51.8% IP, 61.7% IP 1m) during the one-year surveys in comparison to control. In contrast, IRS treated block experienced an increase in both indexes. However, despite IP and IP 1m impacted in Aedes adult and immature indexes with noticeable reductions, the differences in all cases were not significative among the different insecticide treatments. The low sample size and mosquito population levels may have influenced the statistical outcomes. More than 80% of the interviewed residents were satisfied with the effectiveness of the paint and IRS treatments. The determination of the blood cholinesterase activity of tested individuals after the use of the carbamate paint and IRS in this study did not exceed acceptable inhibition limits. This study suggests that the application of propoxur paint by homeowners as full house coverage or as targeted indoor painting can be a safe and accepted intervention method for density reduction of Aedes aegypti populations in urban environments.

(1) Background: We reviewed the logistics of the implementation of pathogen inactivation (PI) using the INTERCEPT Blood System™ for platelets and the experience with routine use and clinical outcomes in the patient population at the Sírio-Libanês Hospital of São Paulo, Brazil. (2) Methods: Platelet concentrate (PC), including pathogen reduced (PR-PC) production, inventory management, discard rates, blood utilization, and clinical outcomes were analyzed over the 40 months before and after PI implementation. Age distribution and wastage rates were compared over the 10 months before and after approval for PR-PC to be stored for up to 7 days. (3) Results: A 100% PR-PC inventory was achieved by increasing double apheresis collections and production of double doses using pools of two single apheresis units. Discard rates decreased from 6% to 3% after PI implementation and further decreased to 1.2% after 7-day storage extension for PR-PCs. The blood utilization remained stable, with no increase in component utilization. A significant decrease in adverse transfusion events was observed after the PI implementation. (4) Conclusion: Our experience demonstrates the feasibility for Brazilian blood centers to achieve a 100% PR-PC inventory. All patients at our hospital received PR-PC and showed no increase in blood component utilization and decreased rates of adverse transfusion reactions.

This paper aims to delve into how gender dimensions observed before, during and after a disaster, have been addressed in two internationally recognised frameworks developed for reducing risks of disasters: Hyogo Framework Action (2005-2015) and Sendai Framework for Disaster Risk Reduction (2015-2030). Building on a systematic review, we evaluate 33 scholarly peer-reviewed journal articles, including book chapters and websites in areas of gender, disaster risk reduction and vulnerability. This study documents a comparative picture of these two frameworks and shows the practical implications of the Sendai Framework for Disaster Risk Reduction (SFDRR) by addressing women’s empowerment in the light of their active participation in disaster risk reduction process. The findings of the study suggest that the frameworks have discussed the reduction of women’s socioeconomic vulnerabilities, as well as encouraged their empowerment. Comparing the two frameworks, it appears in the current study that there has been a significant gap in the existing literature that does not explicitly document comparing and contrasting features of a gender lens in the policy documents.

Macadamia (Macadamia integrifolia) nuts have become an essential commodity crop in Malawi. The nuts are a lucrative commodity and are used for household consumption and income generation among farming families and as a foreign exchange earning crop at country-level. In addition, macadamia production has increased significantly in recent years in the country. Currently, Malawi is the seventh top producer of macadamia nuts, with a global market share of three percent (1,846 metric tonnes on kernel basis). In 2018, exports of macadamia kernel had a value of US$24.3 million (£19.8 million or MKW 18.01 billion). However, the bulk (85%) of the crop is grown on large commercial plantations, but the smallholder sector is emerging as vital for the future growth of the macadamia sub-sector in Malawi. Furthermore, Malawian smallholders consider macadamia production to be a low-input crop with large returns per unit area (US$14.37 kg^-1ha^-1 or MKW 10,701kg^-1ha^-1) thus a lucrative crop with high potential for poverty reduction and wealth creation among these farming families. This paper, therefore, explores: (i) the historical and current trends in macadamia nut production in Malawi; (ii) analyses the country’s macadamia value chain and (iii) discusses the constraints of macadamia production in Malawi for informed policymaking. Thus, the synthesis of the Malawian macadamia sub-sector provides an understanding of the vital contributions of macadamias to Malawi’s economic growth and improvement of livelihoods.

A new generation of universal tools and languages for modeling and simulation multi-physical domain applications emerged and became widely accepted, which generate large-scale systems of differential algebraic equations (DAEs) automatically. Motivated by the characteristics of DAEs systems with large dimension, high index or block structures, we first propose a modified Pantelides’ algorithm (MPA) for any high order DAEs based on its Σ matrix, which is similar to Pryce’s Σ method. By introducing a vital parameter vector, a modified Pantelides’ algorithm with parameter has been presented.It leads to a block Pantelides’ algorithm (BPA) naturally which can immediately compute the crucial canonical offsets for whole (coupled) systems with block-triangular form. We illustrate these algorithms by some examples. And numerical experiments show that the time complexity of BPA can be reduced by at least O(ℓ) compared to the MPA, which is mainly consistent with the results of our analysis.

In addition to being a source of freshener, coffee has an enormous possibility to be developed as a source of antioxidants for functional beverages. However, efforts to increase the value added of coffee as a health functional drink are still hindered by the presence of high level of caffeine, which is thought to have adverse effects on health, especially for coffee lovers who are vulnerable to caffeine. This study aims to optimise the steaming duration to produce low caffeine coffee while maintaining the sensory attributes and antioxidant compounds contained in it. Indonesian Arabica (Leksana variety) green coffee beans were steamed with multi-level steaming durations (0, 20, 40, 60 and 80 min) followed by roasting (medium-dark roast degree), grinding, and brewing (espresso method). The results indicate that caffeine content in the coffee was inversely proportional to the steaming duration. The lowest caffeine content was obtained from the treatment of 80 min steaming with a decrease of caffeine level up to 28.73%. However, the longer process of steaming caused a significant decrease in polyphenol content and antioxidant activity. The hedonic test shows that the steaming treatment of coffee can increase preferences of panellists. There were two driving attributes that influence the overall liking of coffee, namely: bitterness and aftertaste. Coffee obtained from the treatment of 60 min steaming was most preferred by panellists. The results of APLSR biplot mapping show that there was a big change in almost all attributes in the coffee samples after 40 min steaming.

Biological nitrogen (N) provisioning is a seminal function of the gut microbes in several terrestrial insects, given the unbalanced carbon (C) and N ratios of their diets. Although freshwater insects face comparable dietary N limitations like terrestrial insects, little is known about this function by their gut microbiomes. In this study, we investigated microbial nitrate reduction to ammonium pathways as possible routes of biological N provisioning in two freshwater insects; filter-feeding Hydropsychidae and grazers/collectors Baetidae. After incubation in filtered (microbe-free) artificial stream water (ASW) containing dissolved ¹⁵N-labeled nitrate (treatment) or standard nitrate (control), bulk δ¹⁵N values of treatment samples (Baetidae = 100.62 ± 10.23, mean ± S.E.; Hydropsychidae = 76.82 ± 7.20) were significantly higher than controls (Baetidae = 10.14 ± 0.12 ; Hydropsychidae = 9.03 ± 0.20) in both functional feeding groups (F _{(3, 13)} = 296, P < 0.0001). The treatment δ¹⁵N values are cautiously interpreted as reflecting uptake and incorporation of microbe-derived ¹⁵N-metabolites (¹⁵NH₄ or ¹⁵N-amino acids) into host tissues following nitrate reduction to ammonium pathways in the gut lumen. Microbial nitrate reduction to ammonium activities was assessed via the quantification of dissimilatory (nrfA) and assimilatory (nasA) nitrate reduction to ammonium gene transcripts. There were no significant differences between control and treatment groups within each insect groups. Overall, this study provides a demonstration of the feasibility of applying ¹⁵N-stable isotope analysis for investigating, potential symbiotic functions of freshwater insect gut microbiomes, despite the preliminary nature of the results.

One of the key areas of the International Renewable Energy Agency’s (IRENA) programme of work is the analysis of renewable technology costs and performance and the dissemination of these results to as wide an audience as possible. In addition to analysis, IRENA seeks to engage a broad range of stakeholders in the context of this work through the Renewable Costing Alliance. The Costing Alliance brings together companies, industry association, governments and researchers to share, confidentially, data for real-world renewable energy project cost and performance, helping to build further on IRENA’s costing work to date. In this context the authors analyse the current cost differentials and cost reduction potentials for solar PV in Japan compared to best practice levels and identify the reasons for higher costs in Japan and how to reduce them. This study analyses the current installed cost differentials for utility-scale, commercial and residential rooftop solar PV systems. In addition to identifying the reasons for the cost differentials, potential policy recommendations to reduce the cost differential are identified.

The recently proposed Holography-inspired approach to quantum gravity is reviewed and expanded. The approach is based on the foliation of the background spacetime and reduction of the offshell states to the physical states. Careful attention is paid to the boundary conditions. It is noted that the outstanding problems such as the cosmological constant problem and black hole information can be tackled from the common thread of the quantized gravity. One-loop renormalization of the coupling constants and the beta function analysis are illustrated. Active galactic nuclei and gravitational waves are discussed as the potential applications of the present quantization scheme to astrophysics.

Polymeric drag reducers have been developed over many years due to the great number of practical applications. In all of them, the molecular stability is an essential requirement. Usually, polymers break down under turbulent flows, which causes a decrease in their efficiency as drag reducers. Besides that, some specific applications, in agro and biomedical fields, impose a specific requirement that must be fulfilled, which is the use of non-toxic materials. A suitable stable material that is elected to accomplish this necessity is the mucilage of aloe vera, which is a bio-polymer that can be used as an alternative to the synthetic ones. Here, we investigate the role played by the aging of aloe vera on its capacity to reduce drag. The results obtained by ¹H nuclear magnetic resonance indicate that the compositions of young and mature leaves of aloe vera are different and such a difference plays an important role on their efficiency as drag reducers. Tests were performed to analyse the drag reduction in a rotating apparatus and in a pipeline system and the efficiencies of leaves of different ages were compared to their composition. The main conclusion of these experiments is that the young mucilage samples, which are richer in complex polysaccharides and exhibit lower acid contents, are more efficient drag reducers.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

Gold nanoparticles (AuNPs) are currently under intense investigation for biomedical and biotechnology applications, thanks to their ease in preparation, stability, biocompatibility, multiple surface functionalities and size-dependent optical properties. The most commonly used method for AuNPs synthesis in aqueous solution is the reduction of tetrachloroauric acid (HAuCl₄) with trisodium citrate. We observed variations in the pH and concentration of the gold colloidal suspension synthesized under standard conditions, verifying a reduction in the reaction yield by around 46% from pH 5.3 (2.4 nM) to pH 4.7 (1.29 nM). Citrate-capped AuNPs were characterized by UV-visible spectroscopy, TEM, EDS and zeta-potential measurements, revealing a linear correlation between pH and the concentration of the generated AuNPs. This result can be attributed to the adverse effect of protons both on citrate oxidation and on citrate adsorption onto the gold surface, which is required to form the stabilization layer. Overall, this study provides insight into the effect of the pH over the synthesis performance of the method, which would be of particular interest from the point of view of large-scale manufacturing processes.

The consumer’s acceptability of hamburgers elaborated with the flank of culling cows in which the content of salt or fat had been partially replaced was studied. A mixture of potassium chloride, potassium ferrocyanide and sodium ferrocyanide was used as substitutes for the salt. Oat flakes or a mixture of chia and flax seeds were used as substitutes for the fat. The hamburgers were tasted by 34 consumers. Consumers did not detect significant differences between the control and the rest of the formulations. Neither the gender nor the age of the consumers influenced the sensory appraisal. However, many comments regarding texture failures were recorded. Therefore, the substitution of salt and / or fat in the composition of hamburgers made with the flank of cows is a viable alternative for the commercialization of these pieces of low commercial value as long as the texture of the same is adjusted to resemble it to the control.

A simple, effective and environmental-friendly method was adopted for enhancing the photocatalytic activity of g-C3N4 in the reduction of aqueous Cr(Ⅵ) under visible-light irradiation. The enhancement was achieved via treatment of g-C3N4 in organic solvent with addition of NaOH particles by ultrasonic process for two hours. The results demonstrated that the treated g-C3N4 exhibited much higher photocatalytic activity than pristine g-C3N4 in the reduction of Cr(VI) . Under visible light irradiation for 120 min, the reduced ratios of Cr(VI) with the initial concentration of 50 mg/L in the presence of the treated g-C3N4and pristine g-C3N4 were 100% and 37.1%, respectively. With the addition of fulvic acid, Cr(VI) was efficiently removed at 40 min. Based on the characterization results of the structures and other physiochemical properties of the treated g-C3N4 and pristine g-C3N4 by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and UV Vis diffuse reflectance, the possible reasons responsible for the enhanced photocatalytic activity of the treated g-C3N4 were proposed. The yield and mechanism of different exfoliation methods were compared by semi-quantitative method.

Background. Increasing evidence demonstrate that concentration of protein in infant formula >1.9g/100Kcal with high levels of insulinogenic aminoacids is associated with accelerated weight gain, increased fat mass accumulation and risk of adiposity. Purpose of this study was to conduct a systematic review to determine the metabolic effects in infants feed with infant formula optimized in protein. Methods. Systematic review was conducted according PRISMA Statement. RCTs with one intervention group (infant formula with 1.6-1.9gr of protein/100Kcal) and at least one comparative control group (infant formula with >1.9gr of protein/100Kcal) were included. Standardized mean differences (SMD), through random model were calculated. Results. 15 RCT were included. Optimized protein in infant formula was associated with less gain of BMI at 24 months of follow-up (SMD -0.25, IC95% -0.36 to -0.13, p 0.01) and less fat mass accumulation (SMD -0.68, IC95% -0.98 to -0.37, p 0.01). Optimized protein was also associated to less gain of weight, weight/age Z-score, weight/length Z-score, BUN (mmol/dL) and IGF1 (ng/ml). No effect on length/age Z-score was observed. Conclusions. Robust evidence showed optimized protein (1.6gr/100Kcal to 1.9gr/100Kcal) in infant formula is associated with metabolic benefits in infants with less weight gain, BMI and fat mass accumulation.

This paper aims to contribute to refining the e-values for testing precise hypotheses, especially when dealing with nuisance parameters, leveraging the effectiveness of asymptotic expansions of the posterior. The proposed approach offers the advantage of bypassing the need for elicitation of priors and reference functions for the nuisance parameters and the multidimensional integration step. For this purpose, starting from a Laplace approximation, a posterior distribution for the parameter of interest only is considered and then a suitable objective matching prior is introduced, ensuring that the posterior mode aligns with an equivariant frequentist estimator. Consequently, both Highest Probability Density credible sets and the e-value remain invariant. Some targeted and challenging examples are discussed.

Data on Stark broadening parameters, spectral line widths and shifts, for 15 multiplets of N VI, which spectral lines are broadened by collisions with electrons, protons, alpha particles (He III) and B III, B IV, B V and B VI ions, are presented. They have been calculated, using the semiclassical perturbation theory, for temperatures from 50,000 K to 2,000,000 K, and perturber densities from 1016 cm−3 up to 1024 cm−3. These data are particularly of interest for the analysis and modelling of atmospheres of hot and dense stars, as e.g. white dwarfs, and for investigation of their spectra, but also for analyis ad modelling of laser driven plasma in proton-boron fusion research.

In the article, we are trying to find a general law that describes the physical properties of a complex compound through the same physical properties of compound elements. For metal alloys operated under extreme conditions - neutron and proton irradiations and thermal heating, the mechanical properties of these alloys and their elements have been studied. It turned out that the ultimate tensile strength of tantalum alloys used in the design of space reactors can be expressed in terms of the weighted sum of the ultimate tensile strengths of its elements in the range of neutron doses: (0 - 0.96) displacement per atom (dpa) for Ta–10W alloy and (1.4 - 1.7) dpa for T–111 alloy with a neutron energy of more than 0.1 MeV. For tungsten binary alloys used in the design of fusion reactors, the Vickers hardness can also be expressed in terms of the weighted sum of the Vickers hardnesses of the alloy elements in the range of proton irradiation doses: (0 - 0.05) dpa for W-1%Re alloy, (0.05 - 0.2) dpa for W-3%Re alloy and (0.05 - 1) dpa for W-1%Ta with a proton energy of 1 MeV.

Abstract: Scavenging of electrogenerated superoxide radical anion (O2•−) by pyrogallol (PyH3) was investigated on the basis of cyclic voltammetry and in situ electrolytic electron spin resonance spectrum in N,N-dimethylformamide with the aid of density functional theory (DFT) calculations. Quasi-reversible dioxygen/O2•− redox coupe was modified by the presence of PyH3, suggesting that O2•− was scavenged by PyH3 through proton-coupled electron transfer (PCET) involving two proton transfer and one electron transfer. The DFT calculation suggested that the formation of hydrogen bond (HB) complex and the subsequent concerted-two-proton coupled electron transfer (2PCET) characterized by catechol moiety in PyH3 is plausible mechanism which embodies the superior kinetics of the O2•− scavenging by PyH3 as shown in the electrochemical results. Furthermore, it was clarified that three hydroxyl groups of PyH3 promote the formation of prereactive HB complex, in comparative analyses using related compounds, resulting the promotion of the O2•− scavenging.