While L-PBF offers advantages in terms of geometrical freedom or lightweight construction, its use is often limited by economic constraints or currently achievable part costs. With an anticipated increase of L-PBF machine productivity during the next years, an increase of the share of material costs and the share of non-productive time for powder layer application process is to be expected. This results in a demand for less expensive powder materials and advanced processing strategies for the short-and medium-term advancement of L-PBF. As one possible approach, the processing of gas- and water atomized stainless steel (316L) powders with different morphology and particle size distribution as well as their impact on L-PBF productivity is investigated. The actual powder applicability in L-PBF systems and the L-PBF processability determines the minimum necessary powder quality. The main focus of the presented work is put on the interaction between powder quality, powder layer properties, part quality and cost-effectiveness of the L-PBF process. To this end, the influence of the gas and water-atomized powder properties (particle size and morphology) during the powder layer application process at highest possible powder recoater speeds and the resulting powder bed properties (powder layer density, powder bed density, powder demixing) and part properties (part density and tensile strength) is investigated.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

The current study emphasizes on optimizing a suitable ratio of enzymatically hydrolyzed potato powder (EHPP) and whole milk powder (WMP) to produce a quality yogurt by evaluating the physicochemical and rheological properties. The results showed that the addition of EHPP decreased the pH towards acidic conditions which resulted in the high acidity of yoghurt. The proximate composition showed that EHPP increased the ash, protein, water holding capacity (WHC) while fat, synersis, color parameters and total solid were decreased when compared to control yoghurt (CY) sample. Moreover, texture profile (TPA) analysis showed that the addition of EHPP decreased the hardness and cohesiveness while springiness did not show significant difference. Furthermore, rheological properties revealed that EHPP decreased the storage modulus (G’) and loss modulus (G”) when compared with control. In addition to this, sensory analysis revealed that the treatment P4M (1:3) was found as optimum ratio regarding taste, flavor, and aroma. Besides this, scanning electron microscopy (SEM) confirms that the high amount of EHPP resulted in the void holes while CY showed dense gel structure. The prepared yogurt with EHPP provides an excellent flavor, satisfying sweetness and homogeneous texture. These findings suggest the optimum formulation ratio of prepared yogurt was found to be P4M (1:3) for desirable attributes and consumer acceptance. The prepared yogurt from the EHPP presents the potential industrial applications.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

The flow properties of pellets or granules are crucial for further processing the drug dosage forms. Optimal compression or filling the multiparticulate dosage forms into capsules is influenced by forces between discrete particles, which could be partially characterized by flow properties. Several techniques were developed for the examination of flowability, including static and dynamic methods applying empirical studies and the up-to-date chaos theory; however newest methods seem only to be powerful with the supplement of empirical principles. Our experiments try to refine both the technique of analysis and the methods by finding new, alternative ways. Our approach to the flowability measurements was to set up a dynamic time-dependent model which combines empirical observations and the chaos theory on a geometrical basis, thus find new aspects regarding flow properties of pellets and granules that could be relevant for drug developers.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

Hydrotalcites (HTlc) represents a class of nanostructured layered materials that may be employed in a variety of applications, from green to bio technologies. In this paper, we report an investigation on HTlc made of Mg and Fe, recently employed to improve the growth in vitro of osteoblasts within a keratin sponge. We have carried out an analysis of powder materials and of HTlc dispersed in keratin and spin-coated on a Si/SiO2 substrate at different temperatures. A DC magnetic study of the powders has been carried out with a Quantum Design Physical Property Measurement System, equipped with a Vibrating Sample Magnetometer. The data gathered prove that these HTlc are fully paramagnetic, and keratin shows a very small magnetic response. Optical and Atomic Force Microscopy analyses of the thin films provide a detailed picture of clusters randomly dispersed in the films with various dimensions. The magnetic properties of these films have been characterized using the Nano Magneto Optical Kerr Effect (NanoMOKE) down to 7.5K. The data collected show that the local magnetic properties can be mapped with a micrometric resolution distinguishing HTlc regions from keratin ones. This approach opens new perspectives in the characterization of these composite materials.

With proper processing and utilization, biofortified cassava may contribute to the nutritional status of the consumers, thus, the need for this study. High-quality cassava flour from white- (TME 419) and biofortified (TMS 01/1368) cassava varieties were produced at a commercial processing factory, after which the flour is composite with wheat flour to produce bread. The nutritional composition, physical properties and sensory quality of the composite bread were analyzed using standard methods. Results showed that composite bread from 20% biofortified cassava flour (20-YCF) had a higher value of total β-carotene (0.74 μg/g), moisture (37.83%) and ash (2.29%) contents. The fat (3.72%) and protein (12.83%) contents were higher in 20% white cassava flour (20-WCF) composite bread. The 20-YCF composite bread had the highest loaf volume (3286.2 cm3), elasticity (6.32), chewiness (40.51 N) and gumminess (6.41), 20-WCF composite bread had higher specific volume (3.59 cm3/g) and hardness (176.50 N). The 100% wheat bread had higher cohesiveness (0.10) and loaf weight (932.35 g). A significant negative correlation (r = - 0.98, p≤0.05) exist between bread hardness and protein content. The composite bread compared favourably with the 100% wheat bread in terms of weight and aroma, but, the 100% wheat bread was more acceptable.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

The material undergoes high temperature and high strain rate deformation process during cutting process, may induce the dynamic recrystallization behavior and result the evolution of dynamic mechanical properties of the material to be machined. In this paper, the modified Johnson-Cook(J-C) model for Nickel based powder metallurgy superalloy considering dynamic recrystallization behavior in high strain rate and temperature is proposed. The dynamic mechanical properties of the material under different strain rates and temperature conditions are obtained by quasi-static compression test and split Hopkinson pressure bar (SHPB) test. The coefficients of the modified J-C model are obtained by linear regression method. The modified model is verified by comparison with experimental and model prediction results. The results show that the modified J-C model proposed in this paper can accurately describe the mechanical properties of nickel-based powder metallurgy superalloys at high temperature and high strain rate. Which provides help for studying the cutting mechanism and finite element simulation of nickel-based powder metallurgy superalloy.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

Polyamide 11 (PA11) is a plant-based nylon made from castor beans. Powder bed fusion laser sintering (PBF-LS) is an additive manufacturing process used for PA11 which allows the reuse of the unsintered powder. The unsintered powder is mixed with virgin powders at different refresh rates which has been studied extensively for most semi-crystalline polyamides. However, there is lack of information on the effect of using 100% reused PA11 powder and the number of times it is reused on its own during powder bed fusion laser sintering. This paper investigates the effect of reusing PA11 powder in PBF-LS and number of times it is reused on the dimensional accuracy, density, thermal and tensile properties. From 100% virgin powder to 3rd use of the powder, there is a decrease in powder wastage, decrease in crystallinity and tensile strength. These was associated with the polymerisation and cross-linking process of polymer chains, upon exposure to high temperature. This results in a higher molecular weight and hence density. From the 4th use to 10th reuse, the opposite was observed which was associated to an increase in high-viscosity and un-molten particles which resulted in defects in the PBF-LS parts.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

This paper examines the effect of the aggregate type on concrete strength and more specifically how the petrographic characteristics of various aggregate rocks as well as their physico-mechanical properties influences the durability of C 25/30 strength class concrete. The studied aggregate rocks are derived from Veria-Naousa and Edessa ophiolitic complexes as well as granodiorite and albitite rocks from their surrounding areas in central Macedonia (Greece). Concretes are produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concretes. Six different types of aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test verified the initial classification in the same three groups. Group I (ultramafic rocks) presents the lowest concrete strengths, depending on their high alteration degree and the low mechanical properties of ultramafic aggregates. Group II (mafic rocks and granodiorite) presents a wide range of concrete strengths, depending on different petrographic characteristics and mechanical properties. Group III (albite rocks) presents the highest concrete strengths, depending on their lowest alteration degree and their highest mechanical properties. Therefore mineralogy and microstructure of the coarse aggregates affects the final strength of the concrete specimens.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Agriculture is the main economic activity of Mozambique and there is lack of information about the quality of agricultural soils. In this paper, five soils from the Manica and Sussudenga districts (Manica province) were sampled in the years 2021/2022 and 2022/2023 (before and after the rainy seasons), were subjected to an agronomical and environmental chemical analysis to assess its quality, either from the fertility and environmental contamination point of view. Standard analytical methodologies from external certified laboratories and local X-ray fluorescence measurements were used. All the studied soils are acidic (pH ranging from 4.5 and 5.4), have no salinity problems (conductivity ranging from 4.2 to 11.8 mS/m), have low amount of soil organic matter (0.90% to 1.81%), and soils from the Sussudenga district have a very low cation exchange capacity (CEC) (average of 3.33 cmolc/kg), while those from Manica district ranges from very low to average CEC (3.59 to 13.11 cmolc/kg). Also, Sussudenga soils have a phosphorous deficiency (values ranging from <20 to 38.5 mg/kg) and there are deficiencies and/or excesses of some macro and micronutrients in all soil samples. Manica soils are contaminated, apparently from geogenic origin, with Cr (280 to 1400 mg/kg), Co (80 mg/kg), Ni (78 to 680 mg/kg) and V (86 mg/kg). Agricultural soils monitoring must be fostered in Mozambique in order to improve food quality and quantity to assure economic and environmental sustainability.

The aim of this study was to determine the effect of sous-vide and pressure-cooker heating of pork muscles (Longissimus lumborum) on the physicochemical and technological characteristics of pork. The study included an analysis of the basic composition, colour, texture, nutritional value (vitamin B1 content), and rheological properties of meat heated at 60°C for 6-18h and, for comparison, in an autoclave at 121.1°C. The heating conditions affected the weight loss, colour, thiamine content, texture, and rheological properties of the meat. As the heating time increased, the texture determinants of firmness and chewiness decreased, which resulted in softer meat. The differences in the rheological properties of the sous-vide- and autoclave-heated meat resulted from different organ-isation of the spatial matrix of proteins and changes in the structure of muscle fibres caused by the high temperature.

This study evaluated the impact of the level of supplementation of Moringa oleifera leaves on the nutritional (proximate, mineral and vitamin content) as well as on the antioxidant capacities of smoothies made from a blend of pineapple, banana and apple. The beverage (smoothies) were supplemented with Moringa oleifera leaves at 1.5, 3.0 and 4.5% levels and evaluated for proximate, antioxidant (ferric reducing antioxidant power, FRAP and 2,2-Diphenyl-1-picryhydrazy, DPPH), mineral, vitamin, physicochemical and quality acceptability. The results showed that the moisture content of the beverage ranged between 49.24 – 78.62%, total ash: 1.01 – 9.71, crude fiber: 5.14 – 9.39%, crude fat: 0.72 – 1.86%, crude protein: 5.47 – 19.37% and carbohydrate: 3.65 – 16.99%. Calcium (12.03 -15.53) and potassium (17.22 -25.38) were the predominant mineral elements when compared to magnesium (1.51 – 3.05) mg/L. The vitamin contents ranged between 2.5 – 10.8 and 0.15 – 0.93 mg/L for vitamin C and E, respectively. Total phenolic contents ranged between 4.68 – 6.18 mg/ml while the total flavonoid contents ranged between 0.01 – 0.14 mg/ml. The radical scavenging abilities (DPPH) of the samples ranged between 16.05 – 88.77% while the ferric reducing antioxidant power (FRAP) ranged between 0.38 – 7.36 mg/ml. The brix values showed high sugar contents (15 – 18%) while the pH results showed that the sample was almost neutral at a range between 6.3 and 6.5. The overall quality (sensory) acceptability of the different quality parameters evaluated indicated that the control sample was more preferred. While supplementation with Moringa oleifera leaves significantly affected the sensory parameters, its addition nevertheless offers a potential avenue to obtain additional nutrients besides its improved antioxidative properties.

The gel prepared by Nemipterus virgatus (N. virgatus) surimi alone still has some defects in texture and taste. Complexing with polysaccharides is an efficient strategy to enhance the gel properties. The main objective of the study was to analyze the relationship between the gel quality and molecular interaction of N. virgatus surimi gel after complexing with tapioca starch. The results make clear that the gel strength, hardness, and chewiness of surimi gel were increased by molecular interaction with tapioca starch. At the appropriate addition amount (12%, w/w), the surimi gel had excellent gel strength (17.48 N), water holding capacity (WHC) (89.01%), lower cooking loss rate (CLR) (0.95%), and shorted T2 relaxation time. Microstructure analysis indicated that the addition of tapioca starch made the surimi gel evenly distributed in the gel network structure, resulting in a significant reduction in cavities diameter, and the minimum diameter could be reduced to 20.33 μm. In addition, tapioca starch enhanced the hydrogen bond and hydrophobic interaction in the gel system and promoted the transformation of α-helix to β-sheet (P<0.05). Correlation analysis showed that the increased physicochemical properties of surimi gel was closely related to the enhanced non-covalent interactions. In conclusion, the non-covalent complexation with tapioca starch is an efficient strategy to enhance the gel quality of surimi gel.

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.

This study assessed the impact of mineral fertilization on tuber yield and food quality of yam genotypes, specifically Dioscorea alata and Dioscorea rotundata. Four genotypes, each from D. alata and D. rotundata, were used in field experiments conducted in Ibadan, Nigeria, in the 2017 and 2018 cropping seasons. Experiments were conducted under low soil NPK fertility conditions with and without fertiliser treatments. A recommended NPK rate for the area (90, 50, and 75 Kg N, P, K ha-1) was applied to plots with fertiliser treatment. Tuber yield, functional and pasting properties of yam flour, and sensory attributes of pounded yams were collected. The results showed differential responses of the genotypes to tuber yield and food quality with fertiliser application. Fertiliser application has generally increased fresh tuber yield, but it has affected some genotypes' flour quality and textural attributes of the pounded yams. As regards genotypes Danacha and TDa0200012, fertiliser application has increased tuber yield without causing a decrease in tuber quality hence, suggesting Danacha and TDa0200012 as suitable genotypes for maximizing fertiliser productivity. However, in another genotype Ojuiyawo, fertiliser application effectively increased tuber yield but deteriorated tuber quality. Our results suggested that it is crucial to determine the impact of fertilisation on tuber yield and quality for each genotype and select the appropriate genotype to improve productivity through mineral fertilisation. The results of this study can be widely applied to enhance yam productivity in sub-Saharan Africa and useful for sustainable agriculture in yam-growing areas.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

The Chiltan Formation is a potential hydrocarbon-producing reservoir in the Indus Basin, Pakistan. However, its diagenetic alterations and heterogeneous behavior lead to significant challenges in accurately characterizing the reservoir and production performance. This manuscript aims to utilize Chiltan Limestone core samples to conduct a detailed analysis of the diagenetic impacts on reservoir quality. The formation evaluation was carried out through thin section analysis, SEM-EDS and FTIR investigation, as well as plug porosity and permeability measurements under different stress conditions. In results, Petrography revealed three microfacies with distinct diagenetic features and micro-nano fossil assemblages, including intraclasts, pelloids, bioclasts, and stylolites. Diagenesis has a significant impact on petrophysical properties, leading to increased reservoir heterogeneity. The specified depositional environment exposed the alteration of the Chiltan formation during distinct diagenetic phases in marine, meteoric, and burial settings. Pore morphology and mineralogy reveals complex micro-pore structure with various carbonate mineral phases and cement types in the formation samples. The average porosity and permeability of the core samples were found to be 3.4% and 0.449 mD respectively, indicating poor reservoir quality. Stress sensitivity was determined using Klinkenberg corrected permeability, which indicated a reduction in measured and absolute permeability due to increasing confining stress, further reducing the pore throat structure of the formation. In conclusion, the Chiltan formation possesses intricate reservoir heterogeneity and varied micro-pore structure caused by diagenesis and depositional settings. The formation is classified as a low-quality reservoir due to its non-uniform pore geometry, which exhibits low petrophysical properties resulting from overburden stress. The results of this study provide solid foundation in reservoir characterization and quality assessment which has implications for exploring and exploitation of indigenous resources.

Swimming pools are examples of water-intensive facilities, where solutions for reducing economic and environmental costs are increasingly frequently searched. One of the solutions is the recovery of water from wastewater, including from washings obtained through the process of rinsing filter bed. The study objective was the qualitative and quantitative assessment of post-coagulation sludges, the main pollutant found in the washings. During the analyses, assessment of the sedimentation capabilities of the sludges was performed (gravitationally), particle size distribution was assessed (particle size distribution analyzer) and assessment of phytotoxicity with the use of plant indicators in short-term tests was performed (Lemna minor, Lepidium sativum, Sinapis alba, Raphanus sativus). The samples were collected from two independent circulations, which differed in terms of capacity and type of coagulant used. The tested post-coagulation sludges were characterized by high content of total suspended solids: in samples from Circulation 1 from 251 to 128 mg/l, in Circulation 2 from 489 to 228 mg/l. However, the sedimentation processes enabled significant separation of sludges. The hydrolyzed coagulant contributed to the improvement of sedimentation capabilities of sludges. Despite the fact that in many samples low sludge concentrations favored stimulation of plant growth, the post-coagulation sludges can constitute a hazard to plant growth, particularly in the long-term perspective.

This study developed Makgeolli (Korean traditional alcoholic beverage) by adding raw 20% Codium fragile (Cf), a green seaweed, to a mixed base consisting of rice and oats (1:1 ratio) (COM) and analyzed its quality characteristics and antioxidant activity. The rice based Makgeolli supplemented with raw 20% Cf was designated as control (CRM). The physicochemical (pH, acidity), microbiological (yeast, lactic acid bacteria), antioxidant (DPPH, ABTS), and sensory properties (7-henodonic scale) of CRM and COM were investigated during 7 days of fermentation. The pH/acidity levels of CRM and COM reached 3.66/0.68 and 3.69/0.95 after 7 days of fermentation, respectively. Compared to CRM, COM had lower alcohol and sugar contents (P < 0.05) (CRM: 14.5%/9.8 Brix, COM: 11.2%/7.4 Brix). However, COM contained more yeast and lactic acid bacteria (P < 0.05) (CRM: 1.30/4.28 log, COM: 6.04/6.09 log) compared to CRM. The antioxidant activity of DPPH/ABTS (P < 0.05) in COM was approximately 1.5 times that of CRM (CRM: 40.00/51.57%, COM: 56.76/70.91%). In addition, COM had an excellent sensory preference score (P < 0.05) due to its overall fresh flavor and savory taste (CRM: 4.93, COM: 6.06). Therefore, COM was shown to be Makgeolli with enhanced antioxidant function, with yeast and lactic acid bacteria, and improved flavor, suggesting the possibility of commercializing this Makgeolli.

The dessert banana is a popular fruit worldwide, but its ripening process is greatly accelerated by high temperatures, which eventually leads to an unpleasant taste and the appearance of spots on the skin of the fruit. To slow down the ripening of bananas, expensive strategies are used, which are usually not practical for conventional farmers in less developed countries. In this study, we try to find a less costly alternative. Therefore, the effects of coatings of lemon peel extract (2.5 %, 5 %, and 10 %), calcium chloride (4 %), and glycerol (2 %) on the shelf life and postharvest quality of banana fruit (Cavendish) stored at 20 ± 3 °C and 50 – 70 % relative humidity were investigated. Treatment with a mixture of 2.5 % lemon peel extract and 2 % glycerol resulted in an extension of the shelf life of the dessert banana by up to 6 days and no detectable fungal infestation. The mixture is an effective alternative to extend the shelf life and reduce quality losses in bananas.

The beneficial effects of Lanthanide incorporation into 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 (BNT-BT) matrix on its functional properties were investigated. The conventional solid-state method was used for synthesizing samples. The structural refinement revealed that all samples crystallized in R3c rhombohedral symmetry. Raman spectroscopy study was carried out using green laser excitation and revealed that no clear perceptible variation in frequency is observed. Dielectric measurements unveiled that the introduction of rare earth obstructed the depolarization temperature promoted in BNT-BT with decreasing the diffusive phase transition with increasing the lanthanide size. Only Dysprosium addition showed comparable diffusion constant and dielectric behavior as the unmodified composition. Further, the comparison of the obtained ferroelectric hysteresis and strain-electric field loops revealed that only Dy-phase exhibited interesting properties comparing parent composition. In addition, the incorporation of lanthanides Ln3+ into the BNT-BT matrix led to the development of luminescence characteristics in the visible and near infrared regions, depending on the excitation wavelengths. The simultaneous occurrence of photoluminescence and ferroelectric/piezoelectric properties opens up possibilities for BNT-BT-Ln to exhibit multifunctionality in a wide range of applications.Keywords: Sodium Bismuth Titanate; structural refinement; dielectric properties; ferroelectric properties; piezoelectric properties; Photoluminescence.

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with a different N₂ flow rate of 0, 12, 17, 25, 38, 58 sccm. The effects of N₂ flow rate on the electrical properties, crystal structure, elemental composition and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of the N₂ flows. On the other hand, the resistivity increases, the crystal size decreases, and the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta₃N₅ (130,040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N₂ flow rates, and dependent on the crystal size and crystal phase structure.

Quasistatic nanoindentation is a proven tool that provides information on the micromechanical behavior of wood cell walls. However, quasistatic tests cannot probe the time-dependent mechanical behavior shown by wood. Nanoindentation dynamic mechanical analysis (nanoDMA) can mesaure the viscoelastic properties of wood cell walls. This research aimed to study the quasistatic and viscoelastic properties of individual radiata pine wood (Pinus radiata D. Don) cell wall layers. To minimize variability and retrieve both properties at the same locations, a load function composed of a multiload-quasistatic function followed by dynamic reference frequency segments was developed. Nanoindentations were then performed on the S2 layer and compound corner middle lamella (CCML) of unembedded latewood cells. Because the S2 layer is anisotropic, both transverse and longitudinal-tangential wood planes were studied. In the transverse plane, the average results of the quasistatic elastic moduli (Es) for the S2 layer and CCML were 15.7 GPa and 4.6 GPa, respectively. In the longitudinal-tangential plane, the E_s was 3.9 GPa. In the transverse section, the hardness (H) of the S2 layer and CCML were 331 MPa and 277 MPa, respectively, and in the longitudinal-tangential section H was 244 MPa. To acquire the viscoelastic properties, measurements were made over more than three decades of frequency. An increase of the storage modulus (E'), and a reduction of the loss modulus (E'') and loss factor (tan⁡ δ ) as frequency increased were found in both wood orientations. The quasi-static and dynamic indentations equivalent at 0.1 Hz showed similar values for Es and E’. This study contributes to our knowledge of wood cell wall micromechanical properties.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

In this study, we successfully synthesized a novel branched polyamide 6 with ε-caprolactam(CPL) and α-Amino-ε-caprolactam(ACL) through hydrolytic ring-open co-polymerization. The NMR characterization and rheological test result proved the existence of branched chain structure additionally. The branched chain structure caused a remarkable enhancement in the rheological properties. The met index(MFR),zero shear rate viscosity and storage modulus at low frequency region had a remarkable increase.The shear thinning phenomenon became more obvious. The thermal properties test determined by differential scanning calorimetry(DSC) showed that the melting point and crystallinity of co-polymers decreased with the increase of ACL addition.However, the crystal structure of the samples remained unchanged. The appropriate addition amount of ACL can improve the tensile mechanical properties of the co-polymers. When the amount of ACL was 1%, the tensile strength and fracture elongation rate of the co-polymers had the most significant increase.

In this work, the influence of catalyst reuse and reaction time on the yield and quality of organic liquid products (OLP) obtained in a cracking pilot plant at 450 °C and 1.0 atm has been systematically investigated. The distillation of OLP produced 04 (four) distilled fractions. The quality of the biofuels was certified by physical-chemical analysis, as well as FT-IR and GC-MS analysis. The experimental results showed the feasibility of applying the spent sodium carbonate twice in catalytic cracking of vegetable oils. The physical-chemical properties (density, viscosity, acid value, saponification value, and flash point) of OLP decrease as the reaction time increases. The distillation of OLP yields 62.35% (wt.), producing green-like gasoline, kerosene, and diesel fractions rich in hydrocarbons. Therefore, biofuels-like fractions produced by distillation of OLP have a great potential for replacing partially petroleum derived fuels.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

New biocements based on a powdered mixture of calcium phosphate/monetite (TTCPM) modified with the honey addition were prepared by mixing the powder and honey liquid components at a non-cytotoxic concentration of honey (up to 10% (w/v)). The setting process of the cements was not affected by the addition of honey, and the set-ting time of ~4 min corresponded to the fast setting calcium phosphate cements (CPC´s). The cement powder mixture was completely transformed into calcium-deficient nanohydroxyapatite after 24 hours of hardening in simulated body fluid, and columnar growth of long needle-like nanohydroxyapatite particles around the original calcium phosphate particles was observed in honey cements. The compressive strength of honey cements was reduced with the content of honey in the cement. The comparable antibacterial activity of cements with honey solutions was found on Escherichia coli, but very low antibacterial activity was found for Staphylococus aureus for all cements. The enhanced antioxidant inhibitory activity of composite extracts was verified. In vitro cytotoxicity testing verified the non-cytotoxic nature of honey cement extracts, and the addition of honey promoted alkaline phosphatase activity, calcium deposit production, and upregulation of osteogenic genes (osteopontin, osteocalcin, and osteonectin) by mesenchymal stem cells, demonstrating a positive synergistic effect of honey and CPC on the bioactivity of cements that could be promising therapeutic candidates for the repair of bone defects.

The coexistence of ferroelectric and magnetic order parameters in multiferroic materials opens up a host of new collective properties. In particular, the magnetoelectric (ME) effect namely the induction of electric polarization by a magnetic field or magnetization by an electric field has been widely studied in multiferroics. PVDF is a ferroelectric polymer that has attracted considerable research interest for sensing applications. Compared to traditional ceramic composites, the polymer-ceramic nanocomposites offer inherent advantages, including easy processing, mechanical flexibility and the ability to be moulded into complicated configurations for advanced devices with reduced volume and weight. Additionally, polymer composites generally exhibit superior ME coefficients, attributable to the improved displacement transfer capability of the flexible polymer matrix. In this report, free-standing, flexible and lightweight polymer–ceramic nanocomposite thin films with a fixed weight percentage of ferromagnetic CoFe2O4 nanoparticles have been fabricated using a solution casting technique. The structural, microstructural, and electrical properties of the composite have been characterized by standard experimental techniques. The structural and chemical analyses prove a homogeneous dispersion of the fillers in the microstructure of the composite. The electrical response investigated by impedance spectroscopy reveals the contributions of grains and grain boundaries to the whole impedance of the composites. The ac conductivity as a function of frequency obeys Jonscher’s power law. The improved magnetoelectric properties suggest promising applications in multifunctional devices, including field sensor applications.

Metal nanoparticles are extensively studied due to their unique chemical and physical properties, which differ from the properties of their respective bulk materials. Likewise, the properties of heterogeneous bimetallic structures are far more attractive than those of single-component nanoparticles. The incorporation of a second metal into the nanoparticle structure alters the surface plasmon resonance and magnetic properties of the bimetallic composite. This review focuses on the enhanced optical and magnetic properties offered by bimetallic nanoparticles and their corresponding impact on biological applications. We summarize the predominant structures of bimetallic nanoparticles, outline their synthesis methods, and highlight their use in biological applications, both diagnostic and therapeutic, which are dictated by their various optical and magnetic properties.

PZT-Poly(vinylidene fluoride) composites were prepared by hot-pressing method. Before addition, PZT particles were firstly modified with two different coupling agents. The micromorphology, microstructure, dielectric properties, and piezoelectric properties of the composites were characterized and investigated. Results indicated that PZT particles were homogeneously dispersed in the PVDF matrix by the addition of coupling agents. The electric properties of PZT-PVDF composites with NDZ-101 were the best. Especially when the volume ratio of the titanate coupling agent NDZ-101 was 1%, the piezoelectric strain constant d33 of PZT-PVDF composites reached maximum value 19.23pC/N; its relative dielectric constant εr was 67.45; at the same time its dielectric loss tanδ was 0.0766.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

Benzaldehyde and its derivatives are used as food supplements, due to their properties as anti-oxidants and mainly as organoleptic substances. The degradation of these aldehydes produces benzoic acid and benzyl alcohol derivatives, both of which present high toxicity levels. On the other hand, peroxynitrite acts as an oxidizing agent, thus strategies for its production control during food processing could help to improve food quality parameters such as taste, colour and functional properties. Therefore, the control of these degradative oxidation processes is of great interest to the food industry. In order to know in depth this problem, the present article has fo-cused on the kinetic study of the oxidation of aldehydes by peroxynitrite. The proposed mecha-nism justifies all the experimental results, passing through three competitive pathways were per-oxynitrite acts as a radical, nucleophilic or oxidant species. The possible increase of toxic prod-ucts was analyzed.

During Sep. 2011, forty-four Leymus chinensis culms with stroma development were collected from Inner Mongolia. Stromata surrounded the flag leaf sheathes, white, at the final stage of development. Perithecium but not asci were observed under microscope. Nine epichloid endophyte strains were obtained from Tongliao subdivision, and sixteen from Horqin. Morphological and phylogenetic properties of these strains were investigated. Morphological properties of these strains were similar among these 27 strains. Colonies could grow to 28.5~41.1 mm/21d at 25℃; phialides 24.1~26.4 μm long, 2.1~2.5 μm at base, tapering to less than 1.0 μm at tip; conidia reniform to elliptical, 4.7~5.5×2.8~3.5 μm, indicating typical properties of Epichloë endophytes. Based on the sequences of tefA and tubB gene fragments, strains isolated from Inner Mongolia formed a distinct subclade in E. bromolica/ E. yangzii clade, with a bootstrap value of 66% and 64% respectively. Considering morphological and phylogenetic properties, we tend to determine strains isolated from Leymus chinensis as a new taxon. The detailed taxonomic position of this taxon needs further investigations on hybridization or genomic sequence.

Hydrogel wound dressings hold great potential in eliminating bacteria and accelerating the healing process. However, it remains a challenge to fabricate hydrogel wound dressings that simultaneously exhibit excellent mechanical and photothermal antibacterial properties. Here we report the development of polydopamine-functionalized graphene oxide/calcium alginate/Polypyrrole cotton fabric-reinforced hydrogels (abbreviated as rGO@PDA/CA/PPy FHs) for tackling bacterial infections. The mechanical properties of hydrogels were greatly enhanced by cotton fabric reinforcement and an interpenetrating structure, while excellent broad-spectrum photothermal antibacterial properties based on the photothermal effect were obtained by incorporating PPy and rGO@PDA. Results indicated that rGO@PDA/CA/PPy FHs exhibited superior tensile strength in both the warp (289±62.1N) and weft directions (142±23.0N) similar to cotton fabric. By incorporating PPy and rGO@PDA, the swelling ratio was significantly decreased from 673.5% to 236.6%, while photothermal conversion performance was significantly enhanced with a temperature elevated to 45.0 ℃. Due to the synergistic photothermal properties of rGO@PDA and PPy, rGO@PDA/CA/PPy FHs exhibited excellent bacteria-eliminating efficiency for S. aureus (0.57%) and E. coli (3.58%) after exposure to NIR for 20 min. We believe that the design of fabric-reinforced hydrogels could serve as a guideline for developing hydrogel wound dressings with improved mechanical properties and broad-spectrum photothermal antibacterial properties for infected wound treatment.

Hydrogels are three-dimensional crosslinked materials known for their ability to absorb water, exhibit high flexibility, biodegradability, biocompatibility, and mimic properties of different tissues in the body. However, their application is limited by inherent deficiencies in mechanical properties. To address this issue, reduced graphene oxide (rGO) and tannins (TA) were incorporated into alginate hydrogels (Alg) to evaluate the impact of the concentration of these nanomaterials on mechanical and adhesive, as well as cytotoxicity and wound healing properties. Tensile mechanical tests demonstrated improvements in tensile strength, elastic modulus, and toughness upon the incorporation of rGO and TA. Additionally, the inclusion of these materials allowed a greater energy dissipation during continuous charge-discharge cycles. However, the samples did not exhibit self-recovery under environmental conditions. Adhesion was evaluated on pig skin, revealing that higher concentrations of rGO led to enhanced adhesion, while the concentration of TA did not significantly affect this property. Moreover, adhesion remained consistent after 10 adhesion cycles, and contact time before the separation between the material and the surface did not affect this property. The materials were not cytotoxic and promoted healing in human fibroblast model cells. Thus, an Alg/rGO/TA hydrogel with enhanced mechanical, adhesive, and wound healing properties was successfully developed.

Phosphorus (P) is a vital macronutrient crucial for crop productivity. Plants absorb P salts, mainly orthophosphate, from soil, yet the primary P source resides in organic materials. Soil phosphomonoesterases (APases) play a vital role in releasing P from organics via hydrolysis. Acid and alkaline phosphatases are crucial for alleviating P deficiency in plants. In this review focused on agricultural soils, we studied the relationship of biophysicochemical, agricultural management, and climate factors on APases also its connection with crop growth and yields. Our findings indicate a strong linkage between both APases and soil pH, positively influenced by clay content, organic matter, microbial biomass carbon, and nitrogen. Adopting healthy soil practices like balanced organic fertilizer usage, optimal soil water levels, reduced tillage, crop rotation, and using beneficial plant microbes help boost APase activity. However, the connection between APases and crop productivity remains uncertain due to insufficient research in this area. Our review emphasizes the vital need to evaluate the relationship between APases and meso-macrofauna, alongside essential plant nutrients such as potassium, nutrient ratios, and the synergistic effects of various factors. Understanding the rapid, efficient assimilation of P through APases in the plant-soil and/or plant-microbiota ecosystem it can be crucial for crop productivity and yields.

In this study, seven mortar mixes were prepared by replacing natural sand by crumb rubber ,CR, (10%, 25%, 50%, 60%, 75% and 100%). The properties of mortars, both in their fresh and hardened states, were studied. Key characterisitcs, including density, water absorption coefficient, porosity, thermal conductivity, heat capacity, shrinkage/swelling, elastic modulus, compressive strength, flexure strength, fracture energy and performance after exposure to heat, were evaluated. The results obtained showed that as the CR fraction increased, density, initial setting time, and workability decreased but mortars with CR fractions ranged between 25% and 50% are lightweight and can be used for repairing as they fulfill satndards. It was observed that strengths and stiffness decreased with higher CR content while shrinkage increased for CR percentage higher than 60%. However, up to 50% of CR content the mortars obey to the standards for repair. Interestingly, incorporating up to 50% waste tires proved to improve comfort and thermal resistance without affecting thermal inertia. A slight increase in the mass loss is observed when mortars are exposed to high temperatures. Mortars containing CR between 25% and 50% can be classified as lightweight and thermally insulating mortars, suitable for repairing concrete structures in accordance with industry standards.

The electronic, optical, and magnetic properties of Nd-doped ZnO systems were calculated using the DFT/GGA+U method. According to the results, the Nd dopant causes lattice parameter expansion, negative formation energy, and bandgap narrowing, resulting in the formation of an n-type degenerate semiconductor. Overlapping of the generated impurity and Fermi levels results in a significant trap effect that prevents electron-hole recombination. The absorption spectrum demonstrates a redshift in the visible region and improved intensity, leading to enhanced photocatalytic performance. The Nd-doped ZnO system displays ferromagnetic, with FM coupling due to strong spd-f hybridization through magnetic exchange interaction between the Nd-4f state and O-2p, Zn-4s, and Zn-3p states. These findings imply that Nd-doped ZnO may be a promising material for DMS spintronic devices.

Two-dimensional (2D) bismuth oxyhalides (BiOX) have attracted much attention as potential optoelectronic materials. Expecting for their application diversity, we herewith systematically investigate the tunable properties of 2D BiOX by using first principles calculations. Their electronic and optical properties can be modulated by changing the number of monolayers, applying strain, and/or varying the halogen composition. The bandgap shrinks monotonically and approaches the bulk value, the optical absorption coefficient increases, and the absorption spectrum redshifts, as the layer number of 2D BiOX increases. Carrier transport property can be improved by applying tensile strain, and the ability of photocatalytic hydrogen evolution can be obtained by applying compressive strain. General strain engineering will be effective in linearly tune the bandgap of BiOX in a wide strain range. Strain together with halogen composition variation can tune the optical absorption spectrum to be on demand in the range from visible to ultraviolet. It suggests that that 2D BiOX materials have potential serving as tunable novel photodetectors, can be used to improve clean energy techniques, and are prospective in the field of flexible optoelectronics.

The influence of the addition of 2.5, 5, 7.5, and 10.0% of dried Enoki and Maitake mushrooms on the content of bioactive compounds and some pro-health properties of pasta was studied. The qualitative and quantitative analysis of phenolic compounds performed using the LC-MS/MS technique indicated the highest amount of phenolic compounds in pasta supplemented with Maitake. However, all pasta enriched with Enoki mushrooms contained statistically significant-ly higher content of α-glucans in comparison to the control. In samples subjected to gastrointes-tinal digestion, the antioxidant, and potential anti-inflammatory activities were significantly higher than ethanolic and PBS extracts of samples. The ethanolic extracts from pasta fortified with dried Enoki and Maitake mushrooms had higher antioxidant activity (in some of the anti-radical and reducing power assays ) as well as a higher ability to inhibit lipoxygenase (E2.5 and E5 samples) compared to the control sample. Also some in vitro digested samples of pasta en-riched with dried Enoki and Maitake mushrooms showed higher chelating power (E10, M7.5 and M10); reducing power (E5, E7.5, and M10) and lipoxygenase inhibition (E7.5, E10 and M10) than the control. In conclusion, Enoki and Maitake mushrooms can be used for fortification of semo-lina pasta, conferring healthier characteristics of the product.

The solid-state technique was utilized to make a single phase of delafossite CuAlO2, along with 1%, 2%, 3% and 4% silver doped CuAlO2 samples in this study. The content of the samples was investigated using energy dispersive X-ray spectroscopy (EDS) equipped with a field emission scanning electron microscope (FE-SEM). The polycrystalline nature of all of the analyzed cases was confirmed by structural analyses utilizing an X-ray diffraction (XRD) pattern with a simple typical peak of CAO rhombohedral phase. Raman, FT-IR and UV–Vis spectroscopy were used to study the structural, and optical energy band gap (Eg) of Ag doped CuAlO2 nanoparticles. The Kubelka–Munk function was used to calculate the optical band gap of ACAO alloys using diffuse reflectance spectra, and it altered as the Ag ion concentration increased. A. c. impedance spectroscopy was used to investigate the dielectric characteristics of Ag doped CuAlO2 nanoparticles.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

In rock blasting for mining production, stress waves play a major role in rock fracturing along with explosion gases. Better energy distribution improves fragmentation and safety, lowers production costs, increases productivity, and controls ore losses and dilution. Blast outcomes vary significantly with the choice of the explosive and the properties of the rock mass encountered. This study analyzes the effects of rock mass and explosives properties on the blast outcomes through numerical simulation using data from the case study and later validates the simulation results from the field blast fragmentation. The outcomes suggest that, for a given set of rock properties, the choice of explosive has a major influence on the resulting fragmentation. Strong explosives favor large fracture extents in hard rocks, while less strong explosives offer a better distribution of explosive energy and fractures. The presence of rock structures such as rock con-tacts and joints influences the propagation of stress waves and fractures depending on the structures' material properties, intensity and orientations, and the direction and strength of the stress wave. To achieve effective fragmentation, the blast design should mitigate the effect of variability in the rock mass by ensuring adequate energy distribution within the limits of geo-metrical design.

The purpose of this research work was to synthesis bio-derived nanocomposite films by incorporating Na0.5Bi0.5TiO3 (NBT) nanoparticles into Chitosan matrix. The NBT nanoparticles were synthesized using a traditional solid-state technique. Then, through a solution casting approach, flexible composite films were fabricated using Chitosan polymer. The morphology and structural assessments were carried out utilizing scanning electron microscopy (SEM), X-ray diffraction and fourier transform infrared technique. The SEM micrographs showed that NBT nanoparticles were randomly distributed and interconnected with other particles, forming interconnected grains with substantial interspaces within the matrix. The spectral response between 300 and 800 nm of the composites is mainly governed by light scattering of NBT particles with diameter sizes in the 100 - 400 nm range and the bandgap of the NBT phase. The dielectric studies demonstrated that the composite films exhibited higher dielectric values compared to the pure Chitosan film. Besides, the increase of NBT amount was found to increase the dielectric values. Additionally, local piezoelectric measurements reveal the expected piezoelectric and ferroelectric behavior for the NBT particles dispersed into the polymer matrix, as locally probed by Piezoresponse Force Microscopy. The studied system bears interest for advanced biocompatible opto- and piezo-electric materials.

3D printing with cement-based materials is a promising manufacturing technique for civil engineering applications that already allows for the design and the construction of complex and highly customized structures using a layer-by-layer deposition approach. Usually, in this type of additive manufacturing, a mixture of cement, water, aggregate and additives is extruded through a specific print head and deposited in successive layers to form the desired shape. The extrusion mechanism is one of the most expensive parts of the 3D printer. Also, for low scale 3D printers, based on the shape of the extruder and the geometry limitation of the mixing blade, the 3D mixture is often limited to a narrow range of materials due to the risk of layer splitting or blockage. Therefore, there is a need to develop affordable and feasible alternatives to the current design-fabrication-application approach of 3D printers. In this paper, various new designed mixtures of fiber reinforced mortars that can be 3D printed using only a commercially available screw pump are analyzed based on their fresh properties and mechanical characteristics. The reduced facility requirements in this approach allow 3D-printing to be more available for civil engineering applications. With further innovation in the future, this method and mixtures can be extended for sustainable and economically feasible printing of single-family housing units.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

The mechanical properties and stability of hydrophobic surface structures prepared by traditional methods are still the main technical bottlenecks restricting the broad application of hydrophobic systems on workpiece surfaces. In this contribution, we propose a technique called selective laser shock peening (SLSP) to enable large-scale high efficient, low-cost manufacturing of hydrophobic metal surfaces with enhanced mechanical properties for durable applications. Using the method of experimental investigation combined with numerical calculation, the hydrophobic properties, mechanical properties, and tribological properties of the samples prepared under SLSP, all-laser shock peening (ALSP), and non-laser shock peening (NLSP) are studied. The SLSP process could prepare a 3D gradient structure material with surface structures, a two-phase (strong phase, soft phase) distribution on the surface, and a multi-level gradient distribution in the thickness direction. Compared with the 2D gradient structure prepared by the traditional process, 3D gradient structures by SLSP have more significant advantages in improving the wetting behavior and the mechanical properties of the material, which proves SLSP to be a novel method to fabricate functional metal surface structures, with highly high engineering application value.

The reinforcing ability of the fillers results in significant improvements in properties of polymer matrix at extremely low filler loadings compared to conventional fillers. In view of this, present review article describes the different methods used in preparation of different rubber nanocomposites reinforced with nanodimensional individual carbonaceous fillers, such as graphene, expanded graphite, single walled carbon nanotubes, multiwalled carbon nanotubes and graphite oxide, graphene oxide and hybrid fillers consisting combination of individual fillers. This is followed by review of mechanical properties (tensile strength, elongation at break, Young modulus, and fracture toughness) and dynamic mechanical properties (glass transition temperature, crystallization temperature, melting point) of these rubber nanocomposites. Finally, Payne and Mullin Effects have also been reviewed in rubber filled with different carbon based nanofillers.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

Mixtures of methacrylic polymers are the most common materials for making composites to be used as resins for dental and cosmetic applications. Some of these mixtures are composed by poly (ethyl methacrylate) (PEMA) and poly (methyl methacrylate) (PMMA), which constitute a solid component to be mixed with a liquid component made out of methacrylate monomers. The reaction between the thermal initiator benzoyl peroxyde (BPO) present in the solid component and the activator of the polymerization process, N,N-dimethyl-p-toluidine (DMT) present in the liquid component, gives rise to thermoset materials. In the present study, different liquid formulations composed by a mixture of two methacrylic monomers, ethyl methacrylate (EMA) and triethylene glycol dimethacrylate (TEGDMA) for cosmetic applications, were prepared and characterized, using a commercial powder (POW) composed by PEMA and PMMA. With the aim of improving workability during final application of the material, it was necessary to slow down the polymerization rate of liquid formulations. Their thermal behaviour was investigated by DSC in order to check the polymerization rate. Thermal stability of final materials was determined by TGA. DMTA, microindentation hardness and impact tests were performed on final materials, to assess their performance with respect to standard formulation. The combination of thermal and mechanical properties allows choosing which formulations could be suitable for use in cosmetics.

The sensitivity of macroscopic mechanical and thermal properties of grey cast iron is computationally investigated for a variety of graphite microstructures over a wide temperature range. In order to represent common graphite microstructures according to DIN EN ISO 945-1, a synthetic approach is used to algorithmically generate simulation domains. The developed mechanical and thermal model is applied in a large simulation study. The study includes statistical volume elements of the graphite microstructures classes GG-15 and IA2 to IA5, with 10 v.-%, 11 v.-% and 12 v.-% graphite, respectively, for a temperature range from 20 °C to 750 °C. Homogenized macroscopic quantities such as the Young's moduli, Poisson's ratios, yield strengths and thermal conductivities are predicted for the different microstructure classes by applying simulation and data analysis tools of the research data infrastructure Kadi4Mat.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

Ecuador has 4000 Km2 of volcanic nanoclay reserves that could be industrialized. An immediate application is to modify the local AC-20 asphalt with this aggregate. This resource was characterized with FTIR, XRD, FRX, SEM, BET, Laser Granulometry, SPECMIN, TSG, TGA, DTG, DSC and Atmospheric Adsorption. FTIR showed vibration peaks Si and Al. X-ray diffraction indicated the presence of silicates and alumina, BET measured particle size (30 to 250 nm), and the SSA property measured the specific surface area (280.38 m2/g). Chip rock (natural clay) was treated with H2O2 or NaOH or NH3 and evaluated with SPECMIN -TSG obtaining spectra close to vermiculite, allophane and bentonite minerals. At 1000 °C additional samples were calcined in Thermogravimetry (TGA), Differential Thermogravimetry (DTG), Differential Thermal Analysis (DCS), with mass loss around 40%, corresponding to organic matter, hydroxyl (OH) and destruction of its structure with spicule formation at 956 °C. With the DSC there were endothermic and exothermic manifestations. The Si/Al layers would have micro and meso porosity, it was also found to be a nanoparticulate material, with high adsorption capacity. At temperatures above 350 °C, its structure collapsed. Thus, this synthesized nanoclay will be used as an additive to form new materials.

Healthcare personnel are considered one of the sectors of workers most exposed to heavier workloads and work stress. One of the consequences associated with its chronic presence is the development of burnout syndrome. Given that, for the evaluation of this syndrome, the context in which they are to be used must be addressed, the purpose of this work was to analyze the psychometric properties, as well as the structure, and to propose a more suitable version for its application to health professionals, and more specifically, nursing, of the Burnout Brief Questionnaire (CBB). The final study sample was made up 1236 working nursing professionals. An exploratory factorial analysis was carried out and a new model was proposed through a confirmatory factorial analysis. Thus, the validation of the CBB questionnaire for nursing healthcare personnel showed an adequate discrimination of the items and a high internal consistency of the scale. With respect to the factorial analysis, four factors were extracted from the revised model. Specifically, these new factors called Job Dissatisfaction, Social Climate, Personal Impact and Motivational Abandonment, showed an adequate index of adjustment. Thus, the Burnout Revised Brief Questionnaire for nursing staff has favorable psychometric properties, and this Burnout model can be applied to all healthcare professionals.

Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m3) can be enhanced by approximately 484% in a composite (56.86 MJ/m3) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.

Starch is widely applied in various industrial sectors, including the food industry. Starch is used as a thickener, stabilizer, or emulsifier. However, arrowroot starch generally has weaknesses, such as unstable under heating and acidic conditions, which are generally applied to processing in the food industry. Modifications were applied to improve the characteristics of native arrowroot starch. In this study, arrowroot starch was modified by heat-moisture treatment (HMT), octenylsuccinylation (OSA), and dual modification between OSA and HMT in a different sequence, namely HMT followed by OSA, and OSA followed by HMT. This study aims to determine the effect of different modification methods on the physicochemical and functional properties of native arrowroot starch. The result shows that both single HMT and dual modification caused damage to native starch granules, such as the formation of cracks and roughness. Especially for single OSA treatment, there is no significant change in granule morphology after modification. All modification treatments did not change the crystalline type of starch but reduced the RC of native starch. Both single HMT and dual modifications (HMT-OSA, OSA-HMT) increased pasting temperature and setback, conversely decreasing the peak and breakdown viscosity of native starch. Whereas, single OSA has the opposite trend compared with the other modifications. HMT played a greater role in increasing the thermal stability and retrogradation ability of arrowroot starch. Both single modifications (HMT and OSA) increase the hardness and gumminess of native starch, conversely for dual modifications. HMT has a greater effect on color characteristics, where decreased the lightness and whiteness index of native arrowroot starch. Single OSA modification increased swelling volume higher than dual modification. Both single HMT and dual modifications increase water absorption capacity and decrease the oil absorption capacity of native arrowroot starch.

Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

The aim of the present study was to describe and determine changes in the superelastic properties of NiTi archwires after clinical use and sterilization. Ten archwires from five different manufacturers (GAC, 3M, ODS, GC, FOR) were cut in two segments and evaluated using a three-point bending test in accordance with ISO 14841:2006. The centre of each segment was deflected to 3.1mm and then unloaded to 0 N to obtain a load-deflection curve. Deflection at the end of the plateau and forces at 3, 2, 1 and 0.5mm on the unloading curve were recorded. Plateau slopes were calculated at 2, 1 and 0.5mm of deflection. Data obtained were statistically analysed to determine differences (p&lt;0.001). Results showed that the degree of superelasticity and exerted forces differed significantly among brand groups. After three months of clinical use, FOR released a greater force for a longer activation period. GC, EURO and FOR archwires seemed to lose their mechanical properties. GC wires released more force than other brand wires after clinical use. Regarding superelasticity after sterilization, GAC, 3M and FOR wires recovered their properties, while EURO archwires lost more.

We present a numerical illumination model to calculate direct as well as diffuse or Hapke scattered radiation scenarios on arbitrary planetary surfaces. This includes small body surfaces such as main belt asteroids as well as e.g. the lunar surface. The model is based on the raytracing method. This method is not restricted to spherical or ellipsiodal shapes but digital terrain data of arbitrary spatial resolution can be fed into the model. Solar radiation is the source of direct radiation, wavelength-dependent effects (e.g. albedo) can be accounted for. Mutual illumination of individual bodies in implemented (e.g. in binary or multiple systems) as well as self-illumination (e.g. crater floors by crater walls) by diffuse or Hapke radiation. The model is validated by statistical methods. A χ2 test is undertaken to compare simnulated images with DAWN images acquired during the survey phase at small body 4 Vesta.

Mechanical response of bisphenol-F based epoxy cured with amine hardener was investigated in tensile testing. Different types of methods were considered in preparing the tensile samples in order to evaluate their effects on the tensile strength of the cured epoxy system. Specifically, four types of preparation methods were discussed to prepare the tensile samples were considered in the study. Further, the effect of different type of tensile samples on tensile strength of specimens was also considered in the analysis. The experimental results showed that the preparation methods affected the tensile strength of the specimens. Starting from the experimental results, an appropriate testing methodology is proposed for epoxy based nanocomposite composite specimens in order to reduce problems that may arise during the test and to optimize procedures for preparation of specimens.

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

The pomegranate, an ancient plant native to Central Asia, cultivated in different geographical areas including the Mediterranean basin and California, consists of flowers, roots, fruits and leaves. Presently, it is utilized not only for the exterior appearance of its fruit but above all, for the nutritional and health characteristics of the various parts composing this last one (carpellary membranes, arils, seeds and bark). The fruit, the pomegranate, is rich in numerous chemical compounds (flavonoids, ellagitannins, proanthocyanidins, mineral salts, vitamins, lipids, organic acids) of high biological and nutraceutical value that make it the object of study for many research groups, particularly in the pharmaceutical sector. Its interest is mainly addressed to the knowledge of its biological and functional properties and the research of new formulations to apply it in a wide range of diseases such as neoplastic, cardiovascular, viral, inflammatory, metabolic, microbial, intestinal, reproductive and skin diseases. In this review we highlight the health-promoting properties of pomegranate and its bioactive compounds against human diseases.

Sequential properties can violate Bell-type inequalities without direct influence on each other, but only if detected in pairs. This is demonstrated below with theoretical arguments, and with a straightforward toy model. Rotating arrows can have transient qualities that produce maximal Bell violations with predetermined values. Any non-signaling phenomenon (classical, or non-classical) can also be interpreted as local.

Materials design for processing and application requires fundamental understanding of their properties based interatomic interaction. The use of the novel concept of total bond order density (TBOD) as a single quantum mechanical metric to characterize the internal cohesion of a crystal and correlate with the calculated physical properties is particularly appealing. This requires detailed first-principles calculation of the electronic structure, interatomic bonding and related properties. In this article, we use this new concept and apply it to chalcogenide crystals based on data obtained from 25 crystals: Ag₂S, Ag₂Se, Ag₂Te, As₂S₃, As₂Se₃, As₂Te₃, As₄Se₄, Cu₂S, Cu₂Se, Cu₂Te, Cu₄GeS₄, Cu₂SnS₃, Cu₂SnSe₃, GeS₂, GeSe₂, Ge₄Se₉, Sb₂S₃, Sb₂Se₃, Sb₂Te₃, SnS, SnSe, CdSe, CdTe, ZnSe, and ZnTe. Together with the calculated optical and mechanical properties, we demonstrate the efficacy of using this novel approach for materials design that could facilitate the exploration and development of new chalcogenide crystals and glasses. Moreover, the TBOD and its partial components (PBOD) could be the key descriptors in machine learning protocol for broader scale design when a large database is available.

Nanotechnology sparks discussions and concerns about the impacts of new nanomaterials on health and the environment. It holds importance in various domains due to its unique struc-tures. Carbon dots (C-dots) are versatile nanomaterials with applications in bioimaging, sensing, catalysis, polymers, solar cells, and more. They offer desirable characteristics such as stability, cost-effectiveness, biocompatibility, and high photoluminescent quantum yield. C-dots have the potential to replace expensive fluorophores in solar cells. They are catego-rized as carbon quantum dots, graphene quantum dots, and carbonized polymer dots. C-dots have outstanding optical and photoelectric properties with low toxicity. Bottom-up and top-down approaches are used for the synthesis of carbon dots (CDs), with each method im-pacting their physicochemical characteristics. The choice of synthesis method depends on de-sired properties and application requirements. Researchers combine these methods and ex-plore new approaches to enhance synthesis efficiency and tailor CD properties. CDs have di-verse chemical structures with modified oxygen, polymer-based, or amino groups on their surface. Various characterization methods such as HRTEM, XPS, and optical analysis (PL, UV) are used to determine CD structure. Carbon dots (CDs) are cutting-edge fluorescent nano-materials with remarkable qualities such as biocompatibility, low toxicity, environmental friendliness, high water solubility, and photo-stability. They are easily adjustable in terms of their optical properties, making them highly versatile in various fields. CDs find applications in bio-imaging, nanomedicine, drug delivery, solar cells, LEDs, photo-catalysis, elec-tro-catalysis, and other related areas.

Background: The Perceived Inventory of Technological Competency as Caring in Nursing (PITCCN) questionnaire has been designed to measure technological competency as caring in nursing practice. As there were no psychometrically sound instruments to quantify the concept in the Slovene language. The goal was to assess the level of psychometric properties of the PITCCN investigated in Slovene hospitals. Methods: Content validity was conducted with eight experts and quantified by the content validity index (CVI) and the modified Cohen’s kappa index. Face validity was assessed through discussions with participants from the target culture in the pilot study. To assess construct validity and internal consistency, a cross-sectional research methodology was used on a convenience sample of 121 nursing personnel from four hospitals. Principal component analysis (PCA) was used to examine construct validity, while Cronbach’s alpha and adjusted item-total correlations were used to measure internal consistency. Results: The content and face validity of PITCCN were adequate. The scale validity index (S-CVI) was 0.97. Cronbach’s α was 0.92, and subscale reliabilities ranged from 0.810 to 0.925. PCA showed four components, which explained more than 73.49% of the variance. Conclusions: The Slovenian version of PITCCN (PITCCN_SI) has good psychometric properties.

In Summer 2017, huge wildfires in the British Columbia region (Canada) led to the injection of a remarkably high concentration of biomass burning aerosol in the atmosphere. These aerosol masses reached the city of Naples, Italy, since the end of August 2017, where they were characterized by means of a multiwavelength lidar and a sun-sky-lunar photometer. Here we report on the optical and microphysical properties of this aerosol in an intriguing condition, occurring on 4th September 2017, which is characterized by an interesting multi-layered vertical distribution of the aerosol. The Lidar profiles highlighted the presence of four aerosol layers, with two located in the lower troposphere and other two at stratospheric altitudes. A rather thorough characterization of the biomass burning aerosol was carried out. The aerosol depolarization ratio showed an increasing dependence on the altitude with averaged values of 2-4% for the tropospheric layers, which are indicative of almost spherical smoke particles, and larger values in the stratospheric layers, suggestive of aspheric particles. Lidar-derived size distributions were retrieved for the first three aerosol layers, highlighting a higher particle concentration in the fine mode fraction for the layers observed at higher altitude. A dominance of fine particles in the atmosphere (Fine Mode Fraction &gt; 0.8) with low absorption properties (absorption AOD &lt; 0.0025 and SSA &gt; 0.97) was also observed over the whole atmospheric column by sun-photometer data. The space-resolved results provided by the lidar data are consistent with the columnar features retrieved by the AERONET sun-photometer, thus evidencing the reliability and capability of lidar characterization of atmospheric aerosol in a very interesting condition of multiple aerosol layers originating from Canadian fires overpassing the observation station.

The Individual Work Performance Questionnaire (IWPQ) can be defined as the individual be-haviour capable of generating value and competitive advantage for the organization. It is a mul-ti-dimensional construct, consisting of task performance, contextual performance and counter-productive work behavior. Albeit important, a comprehensive measure of individual job per-formance is still lacking in the Italian context. This paper describes the validation of an Italian adaptation of the IWPQ. A back translation procedure was used. To investigate the psychometric properties of the 18-item Italian IWPQ, 1053 participants (502 men, 47.7%; 551 women, 52.3%) were enrolled; the age of participants ranged between 19 and 69 (Mage=34.6, SD= 11.8), and for the oc-cupation, the sample is classified in blue collar 32.5%, pink collar 33% and white collar 34.5%. Exploratory and confirmatory factor analyses and multigroup confirmatory factor analyses were performed to test the structural factor of the IWPQ. The results supported the goodness of the IWPQ in the Italian context and the scales were found consistent with the original structure. One item was omitted due to a low factor loading, resulting in a final 17-item structure. Multigroup confirmatory factor analysis showed that the factor solution was invariant across both gender and occupational category and found evidence of metric invariance, uniqueness and scalar invariance, and structural invariance. Convergent and discriminant validity were also tested and showed.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

Geotechnical investigation is an important site characterization process in engineering construction. Excavation pits and boreholes are popular geotechnical investigation methods for accessing subsurface soil and rock characteristics. Although they are accurate, they are limited to the discrete locations where tests are carried out. The demand for 3D representation has been increasing as an alternative for improved visualization of geotechnical investigations. This study developed a procedure for 3D modelling of geotechnical investigations using open-source software. It improves 3D visualization of geotechnical investigations and characterization of accuracy and uncertainty assessment. Presently, most geotechnical investigations do not regularly report uncertainty assessment despite its importance in risk analysis of the investigations. The procedure developed in this study was tested in a proposed site for construction of an Inland Container Depot where it depicted geotechnical soil properties with more than 80% accuracy on holdout samples. It was able to model both horizontal and vertical variations of the soil properties with quantification of uncertainty. More testing and wide applications are recommended.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

The temperature-dependent energy storage properties of four tungsten bronze phase compounds are studied together with an investigation of their structure and temperature-dependent permittivity response, i.e., Ba6Ti2Nb8O30 (BTN), Ba6Zr2Nb8O30 (BZN), Sr3TiNb4O15 (STN) and Sr3ZrNb4O15 (SZN) ceramics. It was found that BZN has smaller grains and a more porous structure than BTN. SZN shows no clear grain boundaries with the most porous structure among all samples, exhibiting a much lower permittivity response than other samples with no signs of phase transitions from room temperature to 400 °C. Though the energy storage response of those samples is generally quite low, it exhibits rather good temperature stability. It was suggested that by obtaining a denser structure through chemical modification or other methods, those tungsten bronze ceramics with good temperature stability could be promising as energy storage devices when improved energy storage properties are achieved.

Concrete production requires a significant amount of natural resources, with aggregates comprising between 55% and 80% of the total volume. However, over-exploitation of natural aggregates has led to the exploration of alternative materials for use in concrete production. In this study, crushed hazelnut shells were investigated as a partial replacement for fine aggregate, addressing the problem of natural resource depletion and offering a second use for this important agricultural waste product available in Chile. Hazelnut shells were incorporated in percentages of 2.5%, 5%, and 10% by weight of sand for water-cement ratios of 0.4 and 0.5. The compressive strengths at 7 and 28 days and bending tensile strengths at 28 days were determined, alongside physical properties such as workability, temperature, air content, fresh density, and hardened density of the concrete. Our findings show that replacing 2.5% of the fine aggregate with hazelnut shells led to higher compressive strength at 28 days, exceeding the strength of the standard specimens by 9.5%, whereas replacing 5% of the fine aggregate led to the highest bending tensile strength, exceeding the resistance of the standard specimens by 3.5%. Moreover, the 0.4 w/c ratio consistently led to better results for both compressive and bending tensile resistances, with fewer and lower reductions in mechanical resistances compared to the standard mixture. Our results suggest that concrete mixes with hazelnut shells as a replacement for fine aggregate at a percentage of up to 2.5% can be used in constructive systems with compression strengths lower than 17 MPa, and mixtures with up to 10% hazelnut shell replacement can be used in structures with tensile bending stress requirements lower than 6 MPa. Overall, the use of hazelnut shells as a partial replacement for fine aggregate in concrete production presents an environmentally-friendly and cost-effective solution for the construction industry.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

In this study, the Bohler K 190 steel was used. The steel was manufactured by the powder metallurgy (PM) process. The boronizing process was carried out in the range of 1173 to 1323 K, for 1-10 h. The samples were boronized in solid medium, called the Durborid powder mixture. For the microstructural observations, the scanning electron microscopy was utilized for determining the morphology of interfaces and measuring the layers’ thicknesses. The phase composition of boride layers was also determined with X-ray diffraction analysis. To investigate the redistribution of chemical elements redistribution during the boronizing process, the EDS mapping and EDS point analysis were used. The boride layers were constituted by FeB and Fe2B phases except for 1173 K for 1 h. The values of Vickers microhardness of Fe2B, FeB and transition zone were estimated. Finally, to assess the boron activation energies in FeB and Fe2B, the so-called integral method was applied and the results in terms of activation energies were confronted with the literature data.

The study of the inherent factors that influence the isolation of one type of metallosupramolecular architecture over another is one of the main objectives in the field of Metallosupramolecular Chemistry. In this work, we report two new neutral copper(II) helicates, [Cu2(L1)2]·4CH3CN and [Cu2(L2)2]·CH3CN, obtained by means of an electrochemical methodology and derived from two Schiff-based strands functionalized with ortho- and para-t-butyl groups on the aromatic surface. These small modifications let us to explore the relationship between the ligand design and the structure of the extended metallosupramolecular architecture. The magnetic properties of the Cu(II) helicates were explored by EPR spectroscopy and DC magnetic susceptibility measurements.

ZrO2-YO1.5-TaO2.5(ZYTO) composite ceramic is considered to be the candidate of next generation of thermal barrier coatings as its excellent thermal stability and low thermal conductivity in high temperature, however, the mechanical properties and fracture tougheness of ZYTO system may be the shortcomings compared with the 8YSZ. In this study, ZYTO composite ceramics were successfully prepared by chemical coprecipitation reaction, the microsture of resulting composites were studied as a function of doping of M-YTaO4. Mechanical properties, including the density, porosity, hardness and Young's modulus, are determinate; the toughening mechanism were verified by the crack growth behavior of Vickers indentation test Results suggested that M-YTaO4 refines the fluorite phase grain and strengthens the grain interface in the composite ceramic. The thermal mismatch between the second phase and matrix produces residual stress in the bulk and affects the crack propagation behavior. With the increase of M-YTaO4 doping, the grain coarsening and ferroelastic domains are observed in the experiments. The ferroelastic domains with orthogonal polarization directions near crack tip evidences the ferroelastic toughening mechanism. The competition among these crack behaviors, such as cracks deflection, bridging and bifurcation, dominates the actual fracture toughness of the composite. The best toughening formula is determinate in the two-phase region and the highest fracture toughness is about to 3.1MPa·m1/2. Above all, mechanical properties of ZYTO composite ceramics look potential for thermal barrier coatings materials.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

PurposeThis study was designed to characterize the psychometric properties of the Persian version of the Fear of Hospitalization Scale (P-FHS).Design and methodsIn order to evaluate the validity and reliability of the translated scale, a cross-sectional design was employed. Ten experts evaluated the content validity of the Fear of Hospitalization Scale (FHS) after it had been back-translated into Persian. With 612 patients having emergency surgery, construct validity was assessed using exploratory factor analysis (EFA) and confirmatory factor analysis (CFA). The STROBE checklist for cross-sectional studies was followed.FindingsThe results of EFA (n = 306) showed that the fear of hospitalization had three factors. These three factors accounted for 45.28% of the total variance. Also, these factors were confirmed by CFA (n = 306) (root-mean-square error of approximation = (90%. confidence interval) = 0.050 [0.041, 0.058], goodness-of-fit index = 0.945, comparative fit index = 0.968, Non-Normal Fit Index = 0.948, incremental fit index = 0.968, Tucker-Lewis Index = 0.959). The coefficients of Cronbach’s alpha, McDonald’s omega, composite reliability, and maximum reliability for all three factors were greater than 0.7, demonstrating satisfied internal consistency.Practice implicationAccording to the published results, the P-FHS is effective at measuring hospitalization anxiety in patients undergoing emergency surgery. It is advised that nurses in Iranian culture use a legitimate and trustworthy technique to pinpoint the causes of hospitalization anxiety in patients undergoing emergency surgery to give optimal care.

Ultrasonic based inspection of thin-walled structures often requires prior knowledge of their mechanical properties. Their accurate estimation could be achieved in a non-destructive manner employing, e.g., elastic guided waves. Such procedures require efficient approaches for experimental data extraction and processing, which is still a challenging task. An advanced automated technique for material properties identification of an elastic waveguide is proposed in this investigation. It relies on the information on dispersion characteristics of guided waves, which are extracted by applying the matrix pencil method to the measurements obtained via laser Doppler vibrometry. Two objective functions have been successfully tested, and the advantages of both approaches are discussed (accuracy vs computational costs). The numerical analysis employing the synthetic data generated via the mathematical model as well as experimental data shows that both approaches are stable and accurate. The influence of the presence of various modes in the extracted data is investigated. One can conclude that the influence of the corruptions related to the extraction of dispersion curves is not critical if the majority of guided waves propagating in the considered frequency range are presented. Possible extensions of the proposed technique for damaged and multi-layered structures are also discussed.