The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

Process simulation represents an important tool for plant design and optimisation, either applied to well established or to newly developed processes. Suitable thermodynamic packages should be selected in order to properly describe the behaviour of reactors and unit operations and to precisely define phase equilibria. Moreover, a detailed and representative kinetic scheme should be available to predict correctly the dependence of the process on its main variables. This review points out some models and methods for kinetic analysis specifically applied to the simulation of catalytic processes, as a basis for process design and optimisation. Attention is paid also to microkinetic modelling and to the methods based on first principles, to elucidate mechanisms and calculate thermodynamic and kinetic parameters. Different case histories support the discussion. At first, we have selected two basic examples from the industrial chemistry practice, e.g. ammonia and methanol synthesis, which may be described through a relatively simple reaction pathway. Then, a more complex reaction network is deeply discussed to define the conversion of bioethanol into syngas/hydrogen or into building blocks, such as ethylene.

With the advances in industry and commerce, passengers have become more accepting of environmental sustainability issues; thus, more people now choose to travel by bus. Government administration constitutes an important part of bus transportation services as the government gives the right-of-way to transportation companies allowing them to provide services. When these services are of poor quality, passengers may lodge complaints. The increase in consumer awareness and developments in wireless communication technologies have made it possible for passengers to easily and immediately submit complaints about transportation companies to government institutions, which has brought drastic changes to the supply-demand chain comprised of the public sector, transportation companies, and passengers. This study proposed the use of big data analysis technology including systematized case assignment and data visualization to improve management processes in the public sector and optimize customer complaint services. Taichung City, Taiwan was selected as the research area. There, the customer complaint management process in public sector was improved, effectively solving such issues as station-skipping, allowing the public sector to fully grasp the service level of transportation companies, improving the sustainability of bus operations, and supporting the sustainable development of the public sector-transportation company-passenger supply chain.

With the year 2020, the world faced a new threat that affects all areas of life, negatively affects production in all areas, and paralyzes social life. The measures and restrictions taken by the country's governments to prevent the epidemic from spreading rapidly in the society with the effect of the Covid-19 virus, which first appeared in China and spread all over the world, brought a new lifestyle. Covid-19 has been much the impact on electricity use and electricity production in the period in Turkey as in other countries. There was a sharp decline in commercial and industrial electricity use. The coronavirus effect has also been reflected in the electricity demand and the consumption amount has undergone a great negative change. Due to the enactment of measures against the new type of coronavirus (COVID-19) epidemic and the partial or full-time curfews, electricity consumption was moved to homes, supermarkets, and hospitals in April 2020 from places where mass consumption is intense, such as industry, workplaces, and educational institutions. In this study, Covid-19 period, the first cases were examined electricity production and consumption in Turkey as of the date it is seen throughout, in comparison with electricity consumption data in the same month of the previous years corresponding to this period, the effects on electricity generation and consumption habits of this period were examined.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

It is a significant task to assess the safety of the aging offshore jacket platform in order to extend the service life. This paper analyzes the multiple risk factors of an aging jacket platform in Bohai Bay, China and builds the safety evaluation index system, which includes three levels, namely, the target layer, the first-grade indicators layer and the second-grade indicators layer. The target layer consists of three first-grade indicators: ocean environments, structure status, and human and organizational factors. Each first-grade indicator is divided into three second-grade indicators. The weight of each indicator is calculated by analytic hierarchy process to weaken subjective effect. Grey clustering method is applied to estimate the failure risk of the platform in Bohai Bay qualitatively and quantitatively. The assessment standard is divided into five grades and the whitening function of each grey cluster is determined by the assessment scheme. The grey evaluation weight vector of each second-grade indicator is calculated by the table dispatching method. Through layer by layer calculation, the grey assessment value of the target layer is finally estimated by making the grey assessment weight vector single-value and the grey grade is determined according to the maximum principle. The evaluation results show quantitatively that the failure risk grade of the jacket platform in Bohai Bay is medium and the safety assessment method is reasonable and feasible.

Statistical mechanics investigates how emergent properties of macroscopic systems (such as temperature and pressure) relate to microscopic state fluctuations. The underlying idea is that global statistical descriptors of order and variability can monitor the relevant dynamics of the whole system at hand. Here we test the possibility of extending such an approach to psychotherapy research investigating the possibility of predicting the outcome of psychotherapy on the sole basis of coarse-grained empirical macro-parameters. Four good-outcome and four poor-outcome brief psychotherapies were recorded, and their transcripts coded in terms of standard psychological categories (abstract, positive emotional and negative emotional language pertaining to patient and therapist). Each patient-therapist interaction is considered as a discrete multivariate time series made of subsequent word-blocks of 150-word length, defined in terms of the above categories. Static analysis (Principal Component Analysis) highlighted a substantial difference between good-outcome and poor-outcome cases in terms of mutual correlations among those descriptors. In the former, the patient’s use of abstract language correlated with therapist’s emotional negative language, while in the latter it co-varied with therapist’s emotional positive language, thus showing the different judgment of the therapists regarding the same variable (abstract language) in poor and good outcome cases. On the other hand, the dynamic analysis, based on five coarse-grained descriptors related to variability, degree of order and complexity of the series, demonstrated a relevant case-specific effect, pointing to the possibility of deriving a consistent picture of any single psychotherapeutic process. Overall, the results showed that the systemic approach to psychotherapy (an old tenet of psychology) is mature to shift from a metaphorical to a fully quantitative status.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Count data are used in many fields of practice, especially Poisson distribution as a popular choice for the marginal process distribution. If these counts exhibit serial dependence, a popular approach is to use a Poisson INAR(1) model to describe the autocorrelation structure of process. In this paper, the explicit formulas are proposed to evaluate performance characteristics of Double Moving Average control chart (DMA) for Integer valued autoregressive of serial dependence Poisson process. The characteristics of the control chart are frequently measured as Average Run Length (ARL) which means that the average of observations are taken before a system is signaled to be out-of-control. These proposed explicit formulas of ARL are simple and easy to implement for practitioner. The numerical results show that the DMA chart performs better than others when the magnitudes of shift are moderate and large.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Highly flexible manufacturing systems require continuous run-time (self-) optimization of processes with respect to various parameters, e.g. efficiency, availability, energy consumption etc. A promising approach for achieving (self-) optimization in manufacturing systems is the usage of the context sensitivity approach. Thereby the Cyber-Physical Systems play an important role as sources of information to achieve context sensitivity. In this paper it is demonstrated how context sensitivity can be used to realize a holistic solution for (self-) optimization of discrete flexible manufacturing systems, by making use of Cyber-Physical System integrated in manufacturing systems/processes. A generic approach for context sensitivity, based on self-learning algorithms, is proposed aiming at a various manufacturing systems. The new solution is propos encompassing run-time context extractor and optimizer. Based on the self-learning module both context extraction and optimizer are continuously learning and improving their performance. The solution is following Service Oriented Architecture principles. The generic solution is developed and then applied to two very different manufacturing processes. This paper proposes a holistic solution to achieve context sensitivity for Flexible Manufacturing Systems, whereby the knowledge created by applying the context sensitivity approach can be used for (self-) optimization of manufacturing processes.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Multi-stakeholder based construction projects are subject to various risk factors due to dynamic business environments. These risks affect project activities which indirectly impact construction costs, resulting in delays and poor building quality. So, managing these project risks requires suitable risk mitigation strategies to evaluate and analyse their severity. Hence, risk evaluation and assessment of construction projects is a multi-criteria decision making (MCDM) problem. In present real-life problems, evaluation of project risks is often uncertain and even incomplete, and the prevailing methodologies fail to handle such situations. To address the problem, this paper extends the analytical network process (ANP) methodology in the D number domain to handle three types of ambiguous evaluations, viz. complete, uncertain, and incomplete, and assesses the weight of risk criteria. The D number based approach overcomes the deficiencies of the exclusiveness hypothesis and completeness constraint of Dempster-Shafer (D-S) theory. Here, preference ratings of the decision matrix for each decision-maker are determined using a D number extended consistent fuzzy preference relation (D-CFPR). An extended multi-attributive border approximation area comparison (MABAC) method in D number is then developed to rank and select the best alternative risk response strategy. Finally, an illustrative example from construction sector is presented to check the feasibility of the proposed approach. For checking the reliability of alternative ranking, a comparative analysis is performed with different MCDM approaches (D-COPRAS, D-ARAS, D-MABAC, and D-TOPSIS). Based on different criteria weights, a sensitivity analysis of obtained ranking of the hybrid D-ANP-MABAC model is performed for verify the robustness of the proposed method.

The integration of automation and process optimization within the context of AI-powered digital transformation has emerged as a pivotal strategy for organizations aiming to enhance efficiency, foster innovation, and competitiveness. This paper is devoted to present innovative contribution by providing a comprehensive structured roadmap that outlines the foundational principles necessary for the successful integration of automation and optimizing processes within the con-text of emerging AI technologies. The paper introduce a cohesive framework consisting of es-sential key pillars: Data-Driven Insights, Seamless Automation, Adaptive Learning and Contin-uous Improvement, Human-Centric Collaboration, Ethical and Responsible AI, Strategic Align-ment, Scalability, and Innovation. These pillars function as guiding principles to navigate the in-tricate landscape of automation-driven initiatives within AI-powered digital transformation. By embracing these pillars, organizations can embark on a transformative journey that maximizes the potential of automation, fosters innovation, and positions them as leaders in the ever-evolving landscape of AI-driven business operations.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

The future of machine tools will be dominated by highly flexible and interconnected systems, in order to achieve the required productivity, accuracy and reliability. Nowadays, distortion and vibration problems are easily solved in labs for the most common machining operations by using models based on equations describing the physical laws of the machining processes; however additional efforts are needed to overcome the gap between scientific research and the real manufacturing problems. In fact, there is an increasing interest in developing simulation packages based on “deep-knowledge and models” that aid machine designers, production engineers or machinists to get the best of the machine-tools. This article proposes a methodology to reduce problems in machining by means of a simulation utility, which uses the main variables of the system&process as input data, and generates results that help in the proper decision-making and machining planification. Direct benefits can be found in a) the fixture/clamping optimal design, b) the machine tool configuration, c) the definition of chatter-free optimum cutting conditions and d) the right programming of cutting toolpaths at the Computer Aided Manufacturing (CAM) stage. The information and knowledge-based approach showed successful results in several local manufacturing companies and are explained in the paper.

For improving the tracking accuracy and model switching speed of maneuvering target tracking in nonlinear systems, a new algorithm named interacting multiple model fifth-degree spherical simplex-radial cubature filter (IMM5thSSRCKF) is proposed in this paper. The new algorithm is a combination of the interacting multiple model (IMM) filter and fifth-degree spherical simplex-radial cubature filter (5thSSRCKF). The proposed algorithm makes use of Markov process to describe the switching probability among the models, and uses 5thSSRCKF to deal with the state estimation of each model. The 5thSSRCKF is an improved filter algorithm, which utilizes the fifth-degree spherical simplex-radial rule to improve the filtering accuracy. Finally, the tracking performance of the IMM5thSSRCKF is evaluated by simulation in a typical maneuvering target tracking scenario. Simulation results show that the proposed algorithm has better tracking performance and quicker model switching speed when disposing maneuver models compared with IMMUKF, IMMCKF and IMM5thCKF.

One of the major steps toward the industrialization of microbial product(s) is to optimize the cultivation conditions at the large scale bioreactor and successfully control the microbial behavior within large scale production environment. Statistical Design of Experiment was proven to optimize a vast number of microbial processes to achieve robustness and explore possible interactions among the variables. In this research, Taguchi Orthogonal Array was applied to optimize the cultivation condition of a newly isolated Prodigiosin-producing marine bacterial strain, Serratia AM8887, at bioreactor level. Two steps fermentation process was applied; as the productivity was scaled up from shake flask level to a bench top bioreactor (5L) and subsequently to an in-situ sterilization bioreactor system (20L) leading to a yield of 7g/L compared to 100mg/L prior to optimization confirming that; applying Taguchi experimental design is a reliable and good positive option for the optimization of biotechnological processes.. The produced pigment was purified and the chemical structure was revealed by means of Spectrophotometric, Maas Spectrum (MS), Fourier transform infrared (FT-IR), and proton nuclear magnetic resonance (1H-NMR) spectroscopy analysis. The biological activity including antibacterial, antioxidants and cytotoxicity to cancer cells line of the pigment were explored. The pigment showed very characteristic features that could helpful in food, pharmaceuticals and/or textile industries.

The next future using machine tools will be dominated by highly flexible and interconnected systems, in order to achieve the required productivity, accuracy and reliability. Nowadays, distortion and vibration problems are easily solved for the most common cases by sing models based on equations describing the physical laws dominating the machining process; however additional efforts are needed to overcome the gap between scientific research and the real manufacturing problems. In fact, there is an increasing interest in developing simulation packages based on “deep knowledge and models” that aid the machine designer, the production engineer, or machinists to get the best of their machines. This article proposes a systematic methodology to reduce problems in machining by means of a simulation utility, which recognizes, collects and uses the main variables of the system/process as input data, and generates objective results that help in the proper decision-making. Direct benefits by such an application are found in a) the fixture/clamping optimal design, b) the machine tool configuration, c) the definition of chatter free optimum cutting conditions and the right programming of cutting tool path at the Computer Aided Manufacturing (CAM) stage. The information and knowledge-based approach showed successful results in several local manufacturing companies.

Many academics are critical of the current publishing system, but it is difficult to create a better alternative. This review relates to the Sciences and Social Sciences, and discusses the primary purpose of academic journals as providing a seal of approval for perceived quality, impact, significance, and importance. The key issues considered include the role of anonymous refereeing, continuous rather than discrete frequency of publications, avoidance of time wasting, and seeking adventure. Here we give recommendations about the organization of journal articles, the roles of associate editors and referees, measuring the time frame for refereeing submitted articles in days and weeks rather than months and years, encouraging open access internet publishing, emphasizing the continuity of publishing online, academic publishing as a continuous dynamic process, and how to improve research after publication. Citations and functions thereof, such as the journal impact factor and h-index, are the benchmark for evaluating the importance and impact of academic journals and published articles. Even in the very top journals, a high proportion of published articles are never cited, not even by the authors themselves. Top journal publications do not guarantee that published articles will make significant contributions, or that they will ever be highly cited. The COVID-19 world should encourage academics worldwide not only to rethink academic teaching, but also to re-evaluate key issues associated with academic journal publishing in the future.

The production of lithium-ion battery cells is characterized by a high degree of complexit due to numerous cause-effect relationships between process characteristics. Knowledge about the multi-stage production is spread among several experts, rendering tasks such as failure analysis challenging. In this paper, a method is presented, which includes expert knowledge acquisition in production ramp-up by combining Failure Mode and Effects Analysis (FMEA) with a Bayesian Network. We show the effectiveness of this holistic method by building up a large scale, cross-process Bayesian Failure Network in lithium-ion battery production. Using this model, we are able to conduct root cause analyses as well as analyses of failure propagation. The former support operators in identifying root causes once a cell possesses a specific failure by calculating most-probable explanations matched to the individual battery cell data. The latter enable us to analyze propagation of failures and deviations in the production chain and thus provide support for placement of quality gates, leading to a significant reduction in scrap rate. Moreover, it gives an insight into which process steps are key drivers for which final product characteristics.

The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr₂₃C₆ .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

The demand of high data rate and ubiquitous coverage in heterogeneous cellular (HetNets) is increasing progressively. In order to meet this demand, sophisticated model having applied interference reduction scheme and cell association technique is needed. The small base station (sBS)are deployed inside the broadcasting area of macro base station (mBS), in heterogeneous cellular networks (HetNets). Since mBS has high transmission power therefore a large number of users get connected with mBS. This causes disproportion of load distribution across the HetNets. For load balancing users from high power mBS are migrated to low power sBS to increase network capacity and to decrease the load from mBS. This results in interference in the communication signal because of strong mBS Interference. Hence, we need interference management technique to mitigate interference and user association and to efficiently use sBSs’ resources. Inter-cell interference (ICI) limit the HetNets’ performance. Additionally, there exist deliberate jamming interference which depends on jammers transmission power and its proximity with the target, which notably degrades the network performance. In this paper, we employ reverse frequency allocation scheme (RFA) to reduce inter cell interference, deliberate jamming interference and to accomplish load balancing. The proposed setup is analyzed inquisitively and with the help of simulations. The result shows reduction in interferences as well as balance of load distribution in the network achieved by employing RFA scheme together with cell association.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In-process EBM monitoring for quality assurance purposes has been a popular research area. Electronic imaging has recently been investigated as one of the in-process EBM data collection methods, alongside thermal/ optical imaging techniques. Despite certain capabilities of an electronic imaging system have been investigated, experiments are yet to be carried out to benchmark one of the most important features of any imaging systems – spatial resolution. This article addresses this knowledge gap by: (1) proposing an indicator for the estimation of spatial resolution which includes the Backscattered Electrons (BSE) information depth, (2) estimating the achievable spatial resolution when electronic imaging is carried out inside an Arcam A1 EBM machine, and (3) presenting an experimental method to conduct edge resolution evaluation with the EBM machine. Analyses of experimental results indicated that the spatial resolution was of the order of 0.3mm-0.4mm when electronic imaging was carried out at room temperature. It is believed that by disseminating an analysis and experimental method to estimate and quantify spatial resolution, this study has contributed to the on-going quality assessment research in the field of in-process monitoring of the EBM process.

Urban areas are centres of business and innovation. Freight transport is indispensable for the proper functioning of any modern urban society. Urban areas can’t function without an appropriate freight transport system, due to the need to replenish stocks of food and other goods in retail shops. The complexity of the decisions concerning implementation of measures to improve the movement of goods in the city requires tools designed to support this process. The purpose of this article is to introduce the possibility of applying the Analytic Hierarchy Process (AHP) as well as the Decision Making Trial and Evaluation Laboratory Method (DEMATEL) in choosing a set of measures and in analysing in the field of distribution logistics, which will help to solve the delivery problems and streamline the cargo flows in Szczecin, in the context of sustainable development.

Museums and Science Centres are informal education environments that intend to engage the visitors with their exhibits. We present an efficient design process that allows an improved working relationship between museum practitioners, exhibition designers, and visitors. We present the principles and a graphical representation based on the Engagement Profile from previous work. Elements of the design process are evaluated using a learning game at the science centre Engineerium. The evaluation is based on a study with over five hundred visitors to the science centre.

Risk-averse areas such as the medical, aerospace and energy sectors have been somewhat slow towards accepting and applying Additive Manufacturing (AM) in many of their value chains. This is partly because there are still signicant uncertainties concerning the quality of AM builds. This paper introduces a machine learning algorithm for the automatic detection of faults in AM products. The approach is semi-supervised in that, during training, it is able to use data from both builds where the resulting components were certied and builds where the quality of the resulting components is unknown. This makes the approach cost ecient, particularly in scenarios where part certication is costly and time consuming. The study specically analyses Selective Laser Melting (SLM) builds. Key features are extracted from large sets of photodiode data, obtained during the building of 49 tensile test bars. Ultimate tensile strength (UTS) tests were then used to categorise each bar as `faulty' or `acceptable'. A fully supervised approach identied faulty specimens with a 77% success rate while the semi-supervised approach was able to consistently achieve similar results, despite being trained on a fraction of the available certication data. The results show that semi-supervised learning is a promising approach for the automatic certication of AM builds that can be implemented at a fraction of the cost currently required.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

Estimation and planning play a vital role in the construction of an autonomous navigation framework. However, these problems are often considered separately, while planning gives robot a free-collision path towards the desired goal, estimation algorithm presents the executed trajectory in the sense that it has to be closed to the ground truth path as much as possible. Recently, a unified probabilistic framework, which supports solving these problems simultaneously, dubbed STEAP has been proposed. Nevertheless, its current version is only designated for an omni wheels robot, which allows robot to move and turn in vertical direction. Differential drive robot, on the other hand, though limited to move along only one direction, has been used in various situations due to its flexibility and lower cost in hardware designing. Thus, in this extension, our aim is to control a differential drive robot via STEAP. Moreover, in a more complicated environment such as labyrinth or maze, the original STEAP sometimes fails to find a path. Indeed, this problem is mainly caused by the poor initialization and the non-linearity in optimizer constraints. In our implementation, instead of dealing with these constraints, we employ a global planner algorithm such as Dijkstra or RRT to treat STEAP as an effective local planner module that focus on following the global path. Consequently, the experimental results show that the extended STEAP not only able to navigate a differential drive robot but also in a more complicated and unstructured environment.

This paper presents a methodology for determining the sensitivity of the main air flow directions in ventilation subnetworks to changes of aerodynamic resistance and of air density in mine workings. Formulae for determination of the sensitivity of the main subnetwork air flows by establishing the degree of dependency of the air volume stream in a given working on the variations in resistance or air density of other workings of the network have been developed. They have been implemented in the VentGraph mine ventilation network simulator. This software, widely used in Polish collieries provides an extended possibility to predict the process of ventilation, air distribution and, in the case of underground fire, also the spread of combustion gasses. The new method facilitates assessment by mine ventilation services of the stability of ventilation systems in exploitation areas and determine of the sensitivity of the main subnetwork air flow directions to changes of aerodynamic resistance and air density. Recently in some Polish collieries new longwalls are developed in seams located deeper then the bottom of the intake shaft. Such solution is called “exploitation below the level of access” or “sublevel”. The new approach may be applied to such developments to assess the potential of changes of direction and air flow rates. In addition, interpretation of the developed sensitivity indicator is presented. While analyzing air distributions for sublevel exploitation, application of current numerical models for calculations of the distribution results in tangible benefits, such as the evaluation of the safety or risk levels for such exploitation. Application of the VentGraph computer program, and particularly the module POŻAR (fire) with the newly developed options, enables an additional approach to the sensitivity indicator in evaluating air flow safety levels for the risks present during exploitation below the level of the intake shaft. The analyses performed and examples presented enabled useful conclusions in mining practice to be drawn.

There is increasing evidence that the impact of climate change on the productivity of grasslands will at least partly depend on their biodiversity. A high level of biodiversity may confer stability to grassland ecosystems against environmental change, but there are also direct effects of biodiversity on the quantity and quality of grassland productivity. To explain the manifold interactions, and to predict future climatic responses, models may be used. However, models designed for studying the interaction between biodiversity and productivity tend to be structurally different from models for studying the effects of climatic impacts. Here we review the literature on the impacts of climate change on biodiversity and productivity of grasslands. We first discuss the availability of data for model development. Then we analyse strengths and weaknesses of three types of model: ecological, process-based and integrated. We discuss the merits of this model diversity and the scope for merging different model types.

The main focus when developing software is to improve the reliability and stability of a software system. When software systems are introduced, these systems are used in field environments that are the same as or close to those used in the development-testing environment; however, they may also be used in many different locations that may differ from the environment in which they were developed and tested. In this paper, we propose a new software reliability model that takes into account the uncertainty of operating environments. The explicit mean value function solution for the proposed model is presented. Examples are presented to illustrate the goodness-of-fit of the proposed model and several existing non-homogeneous Poisson process (NHPP) models and confidence intervals of all models based on two sets of failure data collected from software applications. The results show that the proposed model fits the data more closely than other existing NHPP models to a significant extent.

Physical-law based models are widely utilized in the aerospace industry. One such use is to provide flight dynamics models for use in flight simulators. For human-in-the-loop use, such simulators must run in real-time. Due to the complex physics of rotorcraft flight, to meet this real-time requirement, simplifications to the underlying physics sometimes have to be applied to the model, leading to model response errors in the predictions compared to the real vehicle. This study investigated whether a machine-learning technique could be employed to provide rotorcraft dynamic response predictions, with the ultimate aim of this model taking over when the physics-based model's accuracy degrades. In the current work, a machine-learning technique was employed to train a model to predict the dynamic response of a rotorcraft. Machine learning was facilitated using a Gaussian Process (GP) non-linear autoregressive model, which predicted the on-axis pitch rate, roll rate, yaw rate and heave responses of a Bo105 rotorcraft. A variational sparse GP model was then developed to reduce the computational cost of implementing the approach on large data sets. It was found that both of the GP models were able to provide accurate on-axis response predictions, particularly when the input contained all four control inceptors and one lagged on-axis response term. The predictions made showed improvement compared to a corresponding physics-based model. The reduction of training data to one-third (rotational axes) or one-half (heave axis) resulted in only minor degradation of the GP model predictions.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

: The cyber-physical gap (CPG) is the difference between the 'real' state of the world and the way the system perceives it. This discrepancy often stems from the limitations of sensing and data collection technologies and capabilities, and is an inevitable issue in any cyber-physical system (CPS). Ignoring or misrepresenting such limitations during system modeling, specification, design, and analysis can potentially result in systemic misconceptions, disrupted functionality and performance, system failure, severe damage, and potential detrimental impacts on the system and its environment. We propose CPG-Aware Modeling & Engineering (CPGAME), a conceptual model-based approach for capturing, explaining, and mitigating the CPG, on top of and in sync with the conventional system model, and as an inherent systems engineering activity. This approach enhances the systems engineer’s ability to cope with CPGs, mitigate them by design, and prevent erroneous decisions, actions, and hazardous implications. CPGAME is a generic, conceptual approach, specified and demonstrated with Object Process Methodology (OPM). OPM is a holistic conceptual modeling paradigm for multidisciplinary, complex, dynamic systems, which is also ISO-19450. We analyze the 1979 Three Miles Island 2 nuclear accident as a prime example of the disastrous consequences of unmitigated CPGs in complex systems.

Configurable process models are frequently used to represent business workflows and other discrete event systems among different branches of large organizations: they unify commonalities shared by all branches and describe their differences, at the same time. The configuration of such models is usually done manually, which is challenging. On the one hand, when the number of configurable nodes in the configurable process model grows, the size of the search space increases exponentially. On the other hand, the person performing the configuration may lack the holistic perspective to make the right choice for all configurable nodes at the same time, since choices influence each other. Nowadays, information systems that support the execution of business processes create event data reflecting how processes are performed. In this article, we propose three strategies (based on exhaustive search, genetic algorithms, and greedy heuristic) that use event data to automatically derive a process model from a configurable process model that better represents the characteristics of the process in a specific branch. These strategies have been implemented in our proposed framework, and tested in both business-like event logs as recorded in a higher educational ERP system, and a real case scenario involving a set of Dutch municipalities.

Syntrophic acetate oxidation operates close to the thermodynamic equilibrium and very little is known about the participating organisms and their metabolism. Clostridium ultunense is one of the most abundant syntrophic acetate-oxidising bacteria (SAOB) found in engineered biogas processes operating with high ammonia concentrations. It has been proven to oxidise acetate in cooperation with hydrogenotrophic methanogens. There is evidence that the Wood-Ljungdahl (WL) pathway plays an important role in acetate oxidation. In this study we analysed the physiological and metabolic capacities of C. ultunense on genome scale and conducted a comparative study of all known characterised SAOB, namely Syntrophaceticus schinkii, Thermacetogenium phaeum, Tepidanaerobacter acetatoxydans and Pseudothermotoga lettingae. The results clearly indicated physiological robustness beneficial for anaerobic digestion environments and revealed unexpected metabolic diversity with respect to acetate oxidation and energy conservation systems., Unlike S. schinkii and Th. phaeum, C. ultunense clearly does not employ the oxidative WL pathway for acetate oxidation, as its genome (and that of P. lettingae) lack important key genes. In both those species, a proton motive force is likely formed by chemical protons involving putative electron-bifurcating [Fe-Fe] hydrogenases rather than proton pumps. No genes encoding a respiratory Ech hydrogenase, as involved in energy conservation in Th. phaeum and S. schinkii, were identified in C. ultunense and P. lettingae. Moreover, two respiratory complexes sharing similarities to the proton-translocating ferredoxin:NAD⁺ oxidoreductase (Rnf) and the Na+ pumping NADH:quinone hydrogenase (NQR) were predicted. These might form a respiratory chain involved in reduction of electron acceptors other than protons. However, involvement of these complexes in acetate oxidation in C. ultunense and P. lettingae needs further study. This genome-based comparison provides a solid platform for future meta-proteomics and meta-transcriptomics studies and for metabolic engineering, control and monitoring of SAOB.

Machine learning is an established and frequently used technique in industry and academia but a standard process model to improve success and efficiency of machine learning applications is still missing. Project organizations and machine learning practitioners have a need for guidance throughout the life cycle of a machine learning application to meet business expectations. We therefore propose a process model for the development of machine learning applications, that covers six phases from defining the scope to maintaining the deployed machine learning application. The first phase combines business and data understanding as data availability oftentimes affects the feasibility of the project. The sixth phase covers state-of-the-art approaches for monitoring and maintenance of a machine learning applications, as the risk of model degradation in a changing environment is eminent. With each task of the process, we propose quality assurance methodology that is suitable to address challenges in machine learning development that we identify in form of risks. The methodology is drawn from practical experience and scientific literature and has proven to be general and stable. The process model expands on CRISP-DM, a data mining process model that enjoys strong industry support but lacks to address machine learning specific tasks. Our work proposes an industry and application neutral process model tailored for machine learning applications with focus on technical tasks for quality assurance.

Considering the important demand of fresh water and its scarce availability, water desalination is an interesting technology, producing about 44 Mm³/year worldwide, but, in general the most common desalination techniques are highly energy demanding. Freezing-Melting (F/M) desalination uses just up to 70% less thermal energy, but is the least used process mainly, due to the difficulty of the salt separation. This study proposes a model able to analyses the thermodynamic potential that allows the salt diffusion during the F/M process, using an aqueous solution of sodium chloride. This should allow to obtain a sensitive analysis of the process to promote the separation between the high concentration brine and the ice with liquid separation by physical process. The unidimensional model is based on the evolution of both processes: thermal and mass diffusions, depending on temperature and saline gradients, predicting whether the salt will remain inside the ice or not. Thus, the thermal potential is adjusted to frozen only when the salt has been "pushed" towards the brine. Mostly models have base their results on the assumption of a “certain value of saline concentration of the liquid fraction”, value in which there is great disagreement. In this paper the calculations are based on the concentration in the solid-liquid interface, which has been extensively studied and there is a coincidence in those results, being the main advantage of the proposed model.

Health information technology has been widely used in healthcare, which has contributed a huge amount of data. Health data has four characteristics: high volume; high velocity; high variety and high value. Thus, they can be leveraged to i) discover associations between genes, diseases and drugs to implement precision medicine; ii) predict diseases and identify their corresponding causal factors to prevent or control the diseases at an earlier time; iii) learn risk factors related to clinical outcomes (e.g., patients’ unplanned readmission), to improve care quality and reduce healthcare expenditure; and iv) discover care coordination patterns representing good practice in the implementation of collaborative patient-centered care. At the same time, there are major challenges existing in data-driven healthcare research, which include: i) inefficient health data exchanges across different sources; ii) learned knowledge is biased to specific institution; iii) inefficient strategies to evaluate plausibility of the learned patterns and v) incorrect interpretation and translation of the learned patterns. In this paper, we review various types of health data, discuss opportunities and challenges existing in the data-driven healthcare research, provide solutions to solve the challenges, and state the important role of the data-driven healthcare research in the establishment of smart healthcare system.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

An astonishing increase in temperature is posing several harmful impacts on crop plants. Heat stress is an abiotic environmental phenomenon that causes limits, inhibits plant growth, metabolism, and productivity worldwide, resulting in losses in production yields. Heat stress is caused by human activities and global warming,s such as greenhouse gases, carbon dioxide, methane, nitrous oxide, and water vapour. There are many pieces of evidence to support that heat stress reduces the crop plants yield worldwide, and the effects of heat stress are challenging to meet nutritional security and global food security for human beings. Heat stress has negative impacts on each developmental stage, including from germination to harvesting. Prevalent approaches for heat adaption is inadequate management that is unable either to increase the crop productivity or sustain ld. Several responses to dissect the relevant knowledge about heat stress mechanism involving morphological phenomena, physiological phenomena, reproductive replies, and molecular responses such as heat shock proteins act as mRNA synthesis, mRNA control (effects of genes during heat stress), the translation process, heat response element. There are such phenomena involving disseminating the knowledge concerning heat stress. In this review, we summarise the effect of heat stress on plant mechanisms, including morphological, biochemical and molecular responses.

Changes in extreme weather patterns are expected under climate change. In this study, a risk assessment was conducted using 4 building damage history datasets and 33 weather datasets (precipitation, wind speed, snow, and temperature) from 230 regions in South Korea to quantitatively analyze and predict building damage caused by potential future natural disasters. Decision tree analysis was used to evaluate building damage risk in 230 regions. The decision tree model to determine the risk of flood, gale, and typhoon was generated, which excluded gales, with less damage. The weight (variable importance) and limit value (damage limit) of the weather variables ware derived using the decision tree model. Using these two factors, we assessed the building damage risk in 230 regions in South Korea until 2100. The number of regions at risk of flood damage increased by more than 30% in average. Conversely, regions at risk of snowfall damage decreased by more than 90%. The regions at risk of typhoons decreased by 57.5% on average, and the number of regions at high risk of typhoon damage increased by up to 62.5% in RCP 8.5. These results can be used as objective data to minimize future building damage throughout South Korea, representing the first step towards sustainable development in the region with respect to disaster response.

It is difficult to capture the real-time online measurement data for biochemical oxygen demand (BOD) in wastewater treatment processes. An optimized extreme learning machine (ELM) based on an improved cuckoo search algorithm (ICS) is proposed in this paper for the design of soft BOD measurement model. In ICS-ELM, the input weights matrices of the extreme learning machine (ELM) and the threshold of the hidden layer are encoded as the cuckoo's nest locations. The best input weights matrices and threshold are obtained by using the strong global search ability of improved cuckoo search (ICS) algorithm. The optimal results can be used to improve the precision of forecasting based on less number of neurons of the hidden layer in ELM. Simulation results show that the soft sensor model has good real-time performance, high prediction accuracy and stronger generalization performance for BOD measurement of the effluent quality compared to other modeling methods such as back propagation (BP) network in most cases.

Censoring occurs when complete follow-up time information is unavailable for patients enrolled in a clinical study. The process is considered to be informative (nonignorable) if the likelihood function for the censoring model cannot be partitioned into a set of response parameters that are independent of the censoring parameters. In such cases, estimated survival time probabilities may be biased, prompting the need for special statistical methods to remedy the situation. The problem is especially salient when censoring is skewed toward the early phase of a study. In this paper, we describe a method to impute censored follow-up times using a counting process method.

LASER cladding is a technique which has as main purpose to improve mechanical properties of materials surface with the addition of thin layers of other materials. Cladding/coating/addition material can be transferred to the substrate by powder injection, wire feeding or paste feeding and by the method of pre-placing the powders on the substrate. LASER cladding as a technique has only about 40 years. Is not yet a current technology and more work is needed, namely in the characterization of mechanical properties of new alloys used as base or cladding materials in this process. In this paper will be done initially an historical approach, followed by a description of the principles of the LASER cladding, a description of the applicability of the process and its advantages and limitations and the paper will end with a state of the art about the advances in new metallic alloys. So, this paper presents a review and the state of the art of the technological process and will be a contribution for the divulgation of this recent technique.

Many scientific and technological problems are studied with the help of computer codes that simulate the phenomena of interest rather than via traditional laboratory experiments. Such models play an important role in neuroscience where they are used to mimic brain function from the sub-cellular to the macroscopic level. Exploration with computer models carries with it a number of statistical challenges: where to sample the input space for the simulator, how to make sense of the data that is generated, how to estimate unknown parameters in the model, how to validate a model. The simulator setting also has some unique problems and possibilities. This review paper describes statistical research on these issues and how that work might be applied to neural simulations.

Different water treatment regiments are revealed to have potential in enriching antibiotic resistant bacteria (ARB). Advanced oxidation processes (AOPs) based disinfection techniques have been studied widely in the recent times due to their advantages over conventional treatment methods. However, bacterial response and adaptations against the hostile environments of AOPs is not clearly understood yet. Based on the existing knowledge on the ways in which bacteria surpass the antibiotic treatment, here we propose few important aspects of bacterial adaptation which could be true for AOPs as well since both antibiotics and AOPs generate reactive oxygen species (ROS) during their modes of action. We discuss the plausible role of ROS in the selection of ARB and bacterial heterogeneity as a strategy to bypass the lethal action of AOPs. Understanding bacterial adaptation during disinfection plays a vital role in devising strategies to outclass the bacterial survival. Hence, more importance should be given to such studies in the near future for the successful implementation of AOPs.

This paper describes a multi-channel in-situ monitoring system developed to better understand defect formation signatures in metal additive manufacturing. Three high-speed imaging modes coupled with an image computer capable of processing and storing these data streams allowed an examination of defect formations signatures and mechanisms. It was found that defects later detected in X-ray computed tomography (CT) scans were related to regions with anomalous heat signatures and powder bed morphology. Automated defect detection algorithms based on these defect signatures captured 80% of defects greater than 300 µm.

Communication is indispensable for today's lifestyle, and thanks to technology, millions of people can communicate as quickly as possible. The effect of this breakthrough has transformed organizations to the degree that they generate billions of emails daily to facilitate their operations. There is implicit information behind this vast corpus of human-generated content that can be mined and used for their benefit. This paper tries to address the opportunity that email logs can bring to organizations and propose an approach to discover process models by combining supervised text classification and process mining. This framework consists of two main steps, text classification, and process mining. First, Emails will be classified with supervised machine learning, and to mine, the processes fuzzy Miner is used. To further investigate the application of this framework, we also applied this framework over a real-life dataset from a case study organization.

Today project management in every field of life is prerequisite for the success of project by increasing quality reduces cost and schedule. But selecting tools and techniques to achieve our objectives and implement our plan fully is very difficult task because choice creates complexity. So, we discuss AHP to make decision simple. Ranking critical success factor, cloud computing services, risk prioritization, selection of right ETL software and many other systems AHP plays its important role. For the improvement of today’s complex systems it is very important to prioritize and select projects to remove the root cause of the problem. To attain the right selection of construction equipment for carrying out schedule tasks with high efficiency, production and financial capability is the main purpose of procurement of construction equipment process. Certain conflicts can occur due to the construction of UML models in a collaborative way. AHP is used to remove these conflicts and for establishing and evaluating modelers judgments. Nowadays it is very important and critical decision to choose the best option from multiple alternatives for a successful career after passing 12th standard and also it affects our future. “AHP and TOPSIS” methods are used for this purpose. In this paper, an “AHP and Fuzzy AHP” based hierarchical trust model has been used to rate the service providers and their various plans for infrastructure as a service.

Abstract: Purpose – In this article we lay out the change management practices adopted by financial firms in small states within the Eurozone. We determine whether these organisations have the ability to identify triggers for change (Red Flags) and subject them to eight thematic elements to understand whether management practices can continue to exist and support operational environments, even when unexpected circumstances affect their day to day operations and processes. In doing this we examine the extent to which the eight thematic elements from the model designed by Dalli Gonzi, (2019) (The Dali Model) can assist organisations in risk identification and business continuity planning. Design/methodology/approach – A self-administered questionnaire purposely designed for this study was administered to personnel working in internal controls within financial institutions of small Eurozone states. The participants were asked to grade statements using a 5-point Likert scale, ‘1’ being ‘totally disagree’ and ‘5’ being totally agree’ to the statement posed under the thematic elements forming the basis of the Dali Model. Findings – Factor analysis provided support for the eight hypothesised dimensions of the decision-making model: connection, capacity, governance, network, policy, training, process improvement, standards. Originality/value – The study provides a better understanding and support of “best practice” in change management through an understanding and assessment of the eight factors that are the basis of this model. It addresses practical recommendations to ensure application to a wider frame of use.

Desalinators are traditionally driven by fossil-fuels but in order to avoid greenhouse emissions, renewable energy must be used. In this paper, a coupling between multi-stage flash distillation apparatus and a parabolic trough solar collector is analyzed. The purpose of this study is to determine the economic feasibility of the system, considering four cities of Saudi Arabia and three different potable water productions. To avoid solar energy intermittency and unavailability at night, thermal storage is implemented. Whereas other researchers made parametric analyses, in this paper, the authors developed a mathematical program which was optimized with the help of GAMS software, where the capital cost of the plant was the objective function. After that, a life cycle cost analysis was carried out for each scenario. Depending on the region and water production, the costs of drinking water vary from 2.26 to 3.93 US$/m³, and from 7440 to 23825 tons of carbon dioxide emissions are avoided. As a consequence of the approach used, low costs are obtained; even though no auxiliary heater is implemented and the lowest irradiance conditions are considered. The results of this study reflect that the proposed process is competitive with respect to the traditional one.

A new requirement for the manufacturing companies in Industry 4.0 is to be flexible with respect to changes in demands, requiring them to react rapidly and efficiently on the production capacities. Together with the trend to use Service-Oriented Architectures (SOA), this requirement induces a need for agile collaboration among supply chain partners, but also between different divisions or branches of the same company. In order to address this collaboration challenge, we~propose a novel pragmatic approach for the process analysis, implementation and execution. This~is achieved through sets of semantic annotations of business process models encoded into BPMN 2.0 extensions. Building blocks for such manufacturing processes are the individual available services, which are also semantically annotated according to the Everything-as-a-Service (XaaS) principles and stored into a common marketplace. The optimization of such manufacturing processes combines pattern-based semantic composition of services with their non-functional aspects. This is achieved by means of Quality-of-Service (QoS)-based Constraint Optimization Problem (COP) solving, resulting in an automatic implementation of service-based manufacturing processes. The produced solution is mapped back to the BPMN 2.0 standard formalism by means of the introduced extension elements, fully detailing the enactable optimal process service plan produced. This approach allows enacting a process instance, using just-in-time service leasing, allocation of resources and dynamic replanning in the case of failures. This proposition provides the best compromise between external visibility, control and flexibility. In this way, it provides an optimal approach for business process models' implementation, with a full service-oriented taste, by implementing user-defined QoS metrics, just-in-time execution and basic dynamic repairing capabilities. This paper presents the described approach and the technical architecture and depicts one initial industrial application in the manufacturing domain of aluminum forging for bicycle hull body forming, where the advantages stemming from the main capabilities of this approach are sketched.

Mushrooms have long rich history in folk medicine, traditional and functional foods due to high content of dietary myco-nutrients. Currently, there is increased interest in finding appropriate food-grade green ex-traction systems capable of extracting these bioactive compounds from dietary mushrooms for applica-tions in various food, pharmacological or nutraceutical formulations. Herein, we evaluated a modified Swiss water process (SWP) method using alkaline and acidic pH at low and high temperature under pressurized conditions as a suitable green food grade solvent to obtained extracts enriched with my-co-nutrients (dietary phenolics, total antioxidants (TAA), vitamins, and minerals) from Chaga. Ultra-high performance liquid chromatography coupled to high resolution accurate mass tandem mass spectrometry (UHPLC-HRAMS-MS/MS) was used to assess the phenolic compounds and vitamin levels in the extracts, while inductively coupled plasma mass spectrometry (ICP-MS) was used to determine the mineral con-tents. Over twenty phenolic compounds were quantitatively evaluated in the extracts and the highest total phenolic content and antioxidant activity was observed at pH11.5 at 100°C. The most abundant phenolic compounds present in Chaga extracts included phenolic acids such as protocatechuic acid 4-glucoside (0.7-1.08µg/mL), syringic acid (0.62-1.18µg/mL), and myricetin (0.68-1.3µg/mL). Vitamins are being reported for the first time in Chaga. pH 2.5 at 100°C treatment shows superior effects in extracting the B vitamins whereas pH 2.5 at 60 and 100°C treatments were outstanding for extraction of total fat-soluble vitamins. Vitamin E content was the highest for the fat-soluble vitamins in the Chaga extract under acidic pH (2.5) and high temp. (100°C) and ranges between 50 to 175 µg/100g Chaga. Antioxidant minerals ranged from 85.94 µg/g (pH7 at 100°C) to 113.86 µg/g DW (pH2.5 at 100°C). High temperature 100°C and a pH of 2.5 or 9.5. The treatment of pH11.5 at 100°C was the most useful for recovering phenolics and antioxidants from Chaga including several phenolic compounds reported for the first time in Chaga. SWP is being proposed herein for the first time as a novel, green food-grade solvent system for the extraction of myco-nutrients from Chaga and have potential applications as a suitable approach to extract nutrients from other matrices. Chaga extracts enriched with bioactive myconutrients and antioxidants may be suitable for further use or applications in the food and nutraceutical industries.

The importance of oxygen in the winemaking process is widely known, as it affects the chemical aspects and therefore the organoleptic characteristics of the final product. Hence, it is evident the usefulness of a continuous and real-time measurements of the levels of oxygen in the various stages of the winemaking process, both for monitoring and for control. The WOW project has focused on the design and the development an innovative device for monitoring the oxygen levels in wine. This system is based on the use of an optical fiber to measure the luminescent lifetime variation of a reference metal/porphyrin complex, which decays in presence of oxygen. The developed technology results in a high sensitivity and low cost sensor head that can be employed for measuring the dissolved oxygen levels at several points inside a wine fermentation or aging tank. This system can be complemented with dynamic modeling techniques to provide predictive behavior of the nutrient evolution in space and time given few sampled measuring points for both process monitoring and control purposes. The experimental validation of the technology has been first performed in a controlled laboratory setup to attain calibration and study sensitivity with respect to different photo-luminescent compounds and alcoholic or non-alcoholic solutions, and then in an actual case study during a measurement campaign at a renown Italian winery.

Current global commitments to reduce emissions of greenhouse gases encourage national targets for renewable generation. Due to its small land mass, offshore wind could help Bahrain to fulfill its obligations. However, no scoping study has yet been carried out. The methodology presented here addresses this research need. It employs Analytical Hierarchy Process and pairwise comparison methods in a Geographical Information Systems environment. Publicly available land use, infrastructure and transport data are used to exclude areas unsuitable for development due to physical and safety constraints. Meteorological and oceanic opportunities are ranked, then competing uses are analyzed to deliver optimal sites for wind farms. The potential annual wind energy yield is calculated by dividing the sum of optimal areas by a suitable turbine footprint, to deliver maximum turbine number. Ten favourable wind farm areas were identified in Bahrain’s territorial waters, representing about 4% of the total maritime area, and capable of supplying 2.68 TWh/yr of wind energy or almost 10% of the Kingdom’s annual electricity consumption. Detailed maps of potential sites for offshore wind construction are provided in the paper, giving an initial plan for installation in these locations.

In this work we aim to experimentally study the nucleation and growth of CaCO3 phases precipitated from supersaturated aqueous solutions in the presence of varying concentrations of sulphate oxyanion. The experiments were conducted under pH conditions close to neutral (7.6) and considering a wide range of initial (SO42-)/(CO32-) ratios (0 to ~ 68) in the aqueous solution. We paid special attention to the evolution of the precipitates during ageing within a time framework of 14 days. The mineralogy, morphology and composition of the precipitates were studied by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy and EDX microanalysis. The concentration of sulphate ions in the reacted aqueous solution was study by ICPs. The experimental results show that the mineral composition of the precipitate recovered in each run varied with the (SO42-)/(CO32-) ratio in the parental solution, which influences the mineral evolution of the precipitates during ageing. We observe that high concentrations of sulphate in the aqueous solution stabilize the vaterite precipitates and inhibit calcite formation. Furthermore, aragonite never precipitates directly form the solution and it is only formed via a dissolution-precipitation process in solutions with high (SO42-)/(CO32-) ratio after long reaction times. Finally, gypsum only precipitates after long ageing in those aqueous solutions with the highest concentration of sulphate. The reaction pathways during ageing, the morphology of the calcite crystals and the composition of vaterite and calcite are discussed considering both, kinetic and thermodynamic factors. These results show a considerably more complex behavior of the system than that observed in experiments conducted under higher pHs and supersaturation levels and lower (SO42-)/(CO32-) ratios in the aqueous phase.

In this paper we present experimental results concerning Acoustic Emission (AE) recorded during cyclic compression tests on two different kinds of brittle building materials, namely concrete and basalt. The AE inter-event times were investigated through a non-extensive statistical mechanics analysis which shows that their decumulative probability distributions follow q-exponential laws. The entropic index q and the relaxation parameter q  1=Tq, obtained by fitting the experimental data, exhibit systematic changes during the various stages of the failure process, namely (q; Tq) linearly align. The Tq = 0 point corresponds to the macroscopic breakdown of the material. The slope, including its sign, of the linear alignment appears to depend on the chemical and mechanical properties of the sample. These results provide an insight on the warning signs of the incipient failure of building materials and could therefore be used in monitoring the health of existing structures such as buildings and bridges.

Evaporation is one of the main processes in the hydrological cycle, and it is one of the most critical factors in agricultural, hydrological, and meteorological studies. Due to the interactions of multiple climatic factors, the evaporation is a complex and nonlinear phenomenon; therefore, the data-based methods can be used to have precise estimations of it. In this regard, in the present study, Gaussian Process Regression (GPR), Nearest-Neighbor (IBK), Random Forest (RF) and Support Vector Regression (SVR) were used to estimate the pan evaporation (PE) in the meteorological stations of Golestan Province, Iran. For this purpose, meteorological data including PE, temperature (T), relative humidity (RH), wind speed (W) and sunny hours (S) collected from the Gonbad-e Kavus, Gorgan and Bandar Torkman stations from 2011 through 2017. The accuracy of the studied methods was determined using the statistical indices of Root Mean Squared Error (RMSE), correlation coefficient (R) and Mean Absolute Error (MAE). Furthermore, the Taylor charts utilized for evaluating the accuracy of the mentioned models. The outcome indicates that the optimum state of Gonbad-e Kavus, Gorgan and Bandar Torkman stations, Gaussian Process Regression (GPR) with the error values of 1.521, 1.244, and 1.254, the Nearest-Neighbor (IBK) with error values of 1.991, 1.775, and 1.577, Random Forest (RF) with error values of 1.614, 1.337, and 1.316, and Support Vector Regression (SVR) with error values of 1.55, 1.262, and 1.275, respectively, have more appropriate performances in estimating PE. It found that GPR for Gonbad-e Kavus Station with input parameters of T, W and S and GPR for Gorgan and Bandar Torkmen stations with input parameters of T, RH, W, and S had the most accurate performances and proposed for precise estimation of PE. Due to the high rate of evaporation in Iran and the lack of measurement instruments, the findings of the current study indicated that the PE values might be estimated with few easily measured meteorological parameters accurately.

In recent times, the process control network (PCN) of oil and gas installation has been subjected to amorphous cyber-attacks which include Denial-of-Service (DoS), Distributed-Denial-of-Service (DDoS), Man-in-the-Middle (MitM) attacks, and this may have been caused majorly by the integration of open network to Operation Technology (OT) as a result of low-cost network expansion. The connection of the OT to the internet for firmware updates, third-party support, or vendor interventions, has exposed the industry to attacks. The inability to detect these unpredictable cyber-attacks exposes the PCN and a successful attack can lead to devastating effects. This paper reviews the different forms of cyber-attacks in PCN of oil and gas installations and proposes the use of machine learning algorithms to monitor data exchanges between the sensors, controllers, processes, and the final control elements on the network so as to detect anomalies in such data exchanges. Python 3.0 Libraries, Deep-Learning Toolkit, MATLAB, and Allen Bradley RSLogic 5000 PLC Emulator software were used in the simulation of process control. The outcome of the experiments shows the reliability and functionality of the different machine-learning algorithms in detecting these anomalies with significant precise attack detections identified using a coarse tree algorithm.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

The building sector has a big potential to reduce the material resource demand needed for building construction and therefore, greenhouse gas (GHG) emissions. Digitalisation can help to make use of this potential and improve sustainability throughout the entire building’s life cycle. One way to address this potential is through the integration of Life-Cycle Assessment (LCA) into the building process by employing Building Information Modelling (BIM). BIM can reduce the effort needed to carry out an LCA and therefore facilitate the integration into the building process. A review of current industry practice and scientific literature shows two main approaches to address BIM-LCA integration. Either the LCA is performed in a simplified way at the beginning of the building process, or it is done at the very end when all the needed information is available, but it is too late for decision-making. One reason for this is the lack of methods, workflows and tools to implement BIM-LCA integration over the entire building process. Therefore, the main objective of this study is to develop an integrated BIM-LCA workflow implemented into a method for the whole building process using an existing structure for cost estimation. A tool is created and used in a case study in Switzerland to test the developed approach. The results of this study show that LCA can be performed continuously in each building phase over the entire building process using existing BIM modelling techniques. The main benefit of this approach is that the re-work caused by the need for re-entering data and the usage of many different software tools that characterise most of the current LCA practices is minimised. Furthermore, decision-making, both at the element and building levels, is supported.

In the present work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated using three fused and crushed alumina powders of different particle size fine, medium and coarse. The influence of the particle size on thermal properties and micro-structural features of the produced coating were investigated by thermal insulation test and detailed image analysis technique, respectively. The analyzed micro-structural features include the total porosity, pore size (fine, medium, and large) and cracks. All types of cracks were considered in calculations as voids and were evaluated according to their sizes as pores. All spray parameters except the particle size were fixed throughout the spraying process. The results revealed that the fine starting powder has produced the densest coating with the lowest total porosity and that the total porosity increases with an increasing particle size. This was expected as powders of smaller particle size will reach a higher in-flight temperature and velocity than powders of bigger particle sizes as long as the same spray parameters are applied. However, a detailed image analysis investigation on the three produced coatings showed that the fraction of fine pores and cracks versus the total porosity is substantially higher in coatings produced by using fine starting powders than those produced using medium and coarse powders. In this work, a connection between the thermal insulation and the porosity fraction, which includes fine pores and cracks, was revealed.

Developing particles of different anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Gold atoms of certain transition state develop monolayer assembly at solution surface around the light glow (known in argon plasma) being generated at bottom of copper capillary (known in cathode). The rate of uplifting gold atoms to solution surface is being controlled by forcing energy (travelling photons) pursuing electrons and high energy photons (in high density) entering to solution. Gold atoms dissociated from the precursor under dissipating heat energy into the solution supplied under propagating photons characteristic current through immersed graphite rod (known in anode). Placing packets of nano shape energy of tuned pulse protocol over compact monolayer assembly comprising transition state atoms develop tiny-sized particles of formed shape. On separation of joint tiny particles into two equilateral triangular-shaped tiny particles, exerting forces of surface format elongate atoms of one-dimensional arrays converting them into structures of smooth elements. Due to immersing level of force, such tiny-shaped particles pack from different zones at centre of light glow where they assembled structures of smooth elements for developing mono-layers of different shapes of particles. Developing one-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from nearly rearward zones of reflection of north-south poles, whereas, developing multi-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from the east-west poles and near regions. Depending on the number of assembled structures of smooth elements at point of nucleation, packing of tiny-shaped particles from different zones develop different shapes of the anisotropic particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles exhibiting unprecedented features are discussed.

The production of butanol, acetone and ethanol by Clostridium acetobutylicum is a biphasic fer-mentation process. In the first phase the carbohydrate substrate is metabolized to acetic and bu-tyric acid, in the following second phase the product spectrum is shifted towards the economi-cally interesting solvents. Here we present a cascade of six continuous stirred tank reactors (CCSTR), which allows performing the time dependent metabolic phases of an ace-tone-butanol-ethanol (ABE) batch fermentation in a spatial domain. Experimental data of steady states under four operating conditions - with variations of the pH in the first bioreactor between 4.3 and 5.6 as well as the total dilution rate between 0.042 1/h and 0.092 1/h - were used to optimize and validate a corresponding mathematical model. Beyond a residence time distribution representation and substrate, biomass and product kinetics this model also includes the differen-tiation of cells between the metabolic states. Model simulations predict a final butanol product concentration of 8.2 g/L and a butanol productivity of 0.75 g/(L h) in the CCSTR operated at a pH in bioreactor 1 of 4.3 and D = 0.092 1/h, while 31 % of the cells are differentiated to the solventogenic state. Aiming at an enrichment of solvent-producing cells, a feedback loop was introduced into the cascade - sending cells from a later state of the process (bioreactor 4) back to an early stage of the process (bioreactor 2). In agreement with the experimental observations, the model accurately predicted an increase of butanol formation rate in bioreactor stages 2 and 3, resulting in an overall butanol productivity of 0.76 g/(L h) for the feedback loop cascade. The here presented CCSTR and the validated model will serve to investigate further ABE fermentation strategies for a controlled metabolic switch.

During the last decades, the production systems have developed different strategies to increase their competitiveness in the global market. In a manufacturing and services systems, Lean Manufacturing has been consolidated through the correct implementation of its tools. The present paper presents a case study developed in a Food Packer company where a Simulation Model was considered as an alternative to reduce the waste time generated by the poor distribution of operations and transportation areas for a product within the factory. As a matter of fact, the company has detected problems on the layout distribution that prevents to fulfill the market demand. In addition, the principal aim was to create a simulation model to test different hypothetical scenarios and alternative designs for the layout distribution without modifying its facilities. Moreover, the implemented methodology was based on classical models of simulation projects and a compendium of the manufacturing systems optimization by simulation process used during the last ten years. Also, a mathematic model supported by the Promodel ® simulation software was developed considering the company characteristics; along with the model development, it was possible to compare the production system performance from the percentage of used locations, the percentage of resources utilization, the number of finished products, and the level of Work in Process (WIP). Finally, the verification and validation stages were performed before running the scenarios in the real production area. The results generated by the implementation of the project represent an increase of 68% in the production capacity and a reduction of 5% in the WIP. In addition, both outcomes are associated with the resources management, which were reassigned to other production areas.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Fuel gas network (FGN) synthesis is a systematic method for reducing fresh fuel consumption in a chemical plant. In this work, we address the synthesis of fuel gas network using block superstructure originally proposed for process design and intensification (Demirel et.al. [1]). Instead of a classical source-pool-sink superstructure, we consider a superstructure with multiple feed and product streams. These blocks interact with each other through direct flows that connect a block with its adjacent blocks and through jump flows that connect a block with all blocks. The blocks with feed streams are viewed as fuel sources and the blocks with product streams are regarded as fuel sinks. Addition blocks can be added as pools when there exists intermediate operations among 9 source blocks and sink blocks. These blocks can be arranged in a I × J two-dimensional grid with I = 1 for problems without pools, or I = 2 for problems with pools. J is determined by the maximum number of pools/sinks. With this representation, we formulate fuel gas network synthesis problem as a mixed-integer nonlinear (MINLP) problem to optimally design a fuel gas network with minimal total annul cost. We present a real-life case study from LNG plant to demonstrate the capability of the proposed approach.

This study identifies the optimal management policy of a given energy storage system (ESS) installed in a grid-connected wind farm for maximizing the monetary benefits and provides guidelines for defining the economic value of the ESS under the optimal management policy and selecting the optimal size of the ESS based on the economic value. Considering stochastic models for wind power and electricity price, we develop a finite-horizon periodic-review Markov decision process (MDP) model to seek the optimal management policy. We also use a simple optimization model to find the optimal storage capacity and charging/discharging capacity of the ESS. By applying our analytic approach to a real-world grid-connected wind farm located in South Korea, we verify the usefulness of this study. Our numerical study shows that the economic value of the ESS is highly dependent on the management policy, wind electricity variability, and the electricity price variability. Thus, the optimal size of ESS should be carefully determined based on the locational characteristics and management policy even with limited investments. Furthermore, this study provides a meaningful policy implication on how much a subsidy the government should provide for installing ESS in a wind farm.

The sustainable development of our world has gain particular attention of a wide range of decisional factors, civil society, business sector, and scientific community, seeing that the prosperity of people and society is possible with the aid of sustained and inclusive economic growth of all countries and regions. Educational environment has a decisive impact on changes in the way that societies are coping with national, regional, and global challenges and opportunities brought by sustainable development. Looking at the implications of HE on the progress of society, the paper addressed the lack of HE institutional capacity to integrate the principles and practices of sustainable development into all aspects of education and learning. The scope of research problem was bounded on the capability of HEI as organization and school to act as entrepreneurial university by combining the scope of its responsibility within the value chain through a practical and effective mechanism needed to align the strategy with sustainable development goals (SDGs). Embarking on the path of SDGs requires HEI to design, launch, implement, and customize specific processes architectures to govern the advance of sustainability approach. The authors applied the process scoping diagram to capture and conceptualize the educational model needed to guide the HEI through the process of change to embrace sustainability into organizational culture and daily operations. It has been used the SIPOC method (Supplier, Input, Process, Output, Customer) with Visio software tool to articulate processes relationships embedded in the educational model of HEI. The benefits relied on the organized view of the work processes needed to be performed to incorporate SDGs into the strategy of any entrepreneurial HEI. Finally, the authors shared their views on the scalability of the model which may be customized and harmonized in accordance with different HE circumstances and priorities. Implementing the proposed educational model requires long-term institutional commitment, transparency, continuous performance improvement, and communicating the strategy for SDGs and its achievements to wider stakeholders.

One of the key challenges of stock trading is the stock prices follow a random walk process, which is a special case of a stochastic process, and are highly sensitive to new information. A random walk process is difficult to predict in the short-term. Many linear process models that are being used to predict financial time series are structural models that provide an important decision boundary, albeit not adequately considering the correlation or causal effect of market sentiment on stock prices. This research seeks to increase the predictive capability of linear process models using the SPDR S\&P 500 ETF (SPY) and the CBOE Volatility (VIX) Index as a proxy for market sentiment. Three econometric models are considered to forecast SPY prices: (i) Auto-Regressive Integrated Moving Average (ARIMA), (ii) Generalized Auto Regressive Conditional Heteroskedasticity (GARCH), and (iii) Vector Autoregression (VAR). These models are integrated into two technical indicators, Bollinger Bands and Moving Average Convergence Divergence (MACD), focusing on forecast performance. The profitability of various algorithmic trading strategies is compared based on a combination of these two indicators. This research finds that linear process models that incorporate the VIX Index do not improve the performance of algorithmic trading strategies.

The paper describes a model of subjective goal-oriented semantics extending standard "view-from-nowhere" approach. Generalization is achieved by using a spherical vector structure essentially supplementing the classical bit with circular dimension, organizing contexts according to their subjective causal ordering. This structure, known in quantum theory as qubit, is shown to be universal representation of contextual-situated meaning at the core of human cognition. Subjective semantic dimension, inferred from fundamental oscillation dynamics, is discretized to six process-stage prototypes expressed in common language. Predicted process-semantic map of natural language terms is confirmed by the open-source word2vec data.

This paper introduces a closed-loop control strategy for maintaining consistency of ink temperature in commercial Drop on Demand (DoD) inkjet printing. No additional sensors or additional actuators are installed in the printhead while achieving the consistency in ink temperature. To this end, this paper presents a novel in situ sensing-actuation policy at every individual ink-nozzle, where the jetting mechanism has three distinct roles. It is used for jetting liquid droplet onto the print media based on the print-job. It is used as a softsensor to estimate the real-time liquid temperature of the jetting nozzle. While not jetting liquid, it is used as a heating actuator to minimize the gradient of liquid temperature among jetting nozzles. The soft-sensing based in situ controller is implemented in an experimentally validated digital twin that models the thermo-fluidic processes of the printhead. The digital twin is scalable and flexible to incorporate an arbitrary number of inknozzles, making the control strategy applicable for future designs of the printhead.

The introduction of social commerce ushered in a new era in business-consumer interaction. As a result, more power has passed from the vendor to the buyer, primarily fueling e-commerce acceptance. As a result, understanding consumer behaviour in the context of social commerce adoption has become essential for businesses looking to persuade customers by using the power of social ties and support.Furthermore, such social ties will facilitate trust as the most promising benefit while reducing perceived risk, which has always been a critical problem with online commerce. This study proposes a paradigm for understanding the impact of social commerce on the stages of the consumer decision-making process: need recognition, information search, alternative evaluation, purchase decision, and post-purchase behaviour, with a focus on social support. In this respect, relevant literature in the subject of social commerce either (1) lacks an adequate explanatory model, (2) has a solid theoretical base, or (3) contains practically complex theories with insufficient empirical data. The research model applies the Social Commerce Constructs (SCC): recommendations and referrals, forums and communities, and ratings and reviews to study the respective influence on the consumer decision-making process phases. This paper aims to understand the influence of social commerce on an integrative model that incorporates all customer choice phases while expecting new knowledge. Furthermore, it is advised that this conceptual model be empirically verified to evaluate the practical consequences.

The Needleman-Wunsch process is a classic tool in bioinformatics, being a dynamic programming algorithm that performs a pairwise alignment of two input biological sequences, either protein or nucleic acid. A distance matrix between the tokens used in the sequences is also required as input. The distance matrix is used to generate a positional pairwise similarity matrix between the input sequences, which is in turn used to generate a dynamic programming matrix. The best path through the dynamic programming matrix is navigated using a traceback procedure that maximises similarity, inserting gaps as necessary. Needleman-Wunsch can align both nucleic acids or proteins, which use alphabets of size 4 and 20 tokens respectively. It can also be applied to any other kind of sequence where distance matrices can be specified. Here, we apply it to chains of Pousseur’s Scambi electronic music fragments, of which there are 32, and which Pousseur categorised by their sonic properties, thus permitting the consecutive construction of distance, similarity and dynamic programming matrices. Traceback through the dynamic programming matrix thus produces contrapuntal duet compositions in which two Scambi chains are played in the maximally euphonious manner, providing also an illustration of the principles of biological sequence alignment in sound.

The planning of rural land depends to a large extent on the agrarian and forestry development model agreed upon for it. Within the framework of agrarian multifunctionality, to evaluate different development alternatives and their effect on territorial planning, its multiple dimensions must be considered as well as the interests and needs of the stakeholders. This work thus addresses the comprehensive evaluation of development alternatives for the rural area of a municipality of the Basque Country (Spain) through the implementation of a multi-criteria evaluation method with social participation. The results show, firstly, the existence of trade-offs between the functions to be promoted in the various development models evaluated. Secondly, the results indicate the need to reverse recent trends in the sector and the convenience of moving towards an agro-livestock model of greater ecological and local character, independently of the followed forest model. In fact, the evaluation carried out also reveals, thirdly, the existence of more or less latent conflicts, in particular with regards to forest policy.

Inadequate data linking geology and health in Developing Countries contributes immensely to the challenges to identify sources and causes of many of the emerging diseases. Deficiencies and toxicities of trace elements generally impact human and animal health. The review of the geology of Ghana suggests the presence of oxides and sulphide minerals that are released into the natural environment during the geological process of weathering which introduce both essential and, potentially harmful elements. Of great concern is the fact that majority of the Ghanaian population eat locally cultivated food and expect to be nourished from the diet. Furthermore, archived reports on Ghana rural drinking water indicates most of the aquifers are enriched in As and F while deficient in Mg. Medical geology, the emerging discipline that attempts to address the environmental health issues emanating from geological processes is known in developed nations but not much of its activities are recognized in Ghana. This review has identified the concentrations of a number of elements in different geological settings and have linked these concentrations with health issues. There is therefore a need for medical geologists to work together with other disciplines to devise preventive as well as mitigative techniques in addressing many geology related health issues in Ghana.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

Polyphenols are well-known health promoting agents, but they have some limitations due to their spontaneous oxidation. This evidence has limited their use as drugs in the last years. In this field, several chemical modifications have been proposed to overcome these restrictions; among these, the esterification seems to be the preferred. Ester derivatives could be able to reduce the bioavailability problems connected to polyphenols. On the other hand, the presence of the esterase enzymes in the body guarantees the ester hydrolysis, which in turn frees the two molecules that make it up. Lipase-catalyzed esterifications afforded several derivatives of flavonoids glycosides, in green conditions. In this short note, pancreatic porcine lipase was firstly used as a cheap bio-catalyst, to synthesize oleoyl derivatives of quercetin in aglycone form. Results demonstrated how the enzyme acyl regioselective in position C-3, with high yields and easy purification processes

Precipitation processes are technologies commonly used in hydrometallurgical plants to recover metals or to treat wastewaters. Moreover, solid-liquid separation technologies, such as thickening or filtering, are relevant unit operations, included in the precipitation technologies. These methods are strongly dependent on the characteristics of the solid precipitates formed during the specific precipitation reaction. One of these characteristics is the particle size distribution (PSD) of the solid precipitates which are fed into a solid-liquid separation process. Therefore, PSD determination is a typical practice for the characterization of the slurries generated in a precipitation plant. Furthermore, the precipitates generated in these processes have a colloidal or aggregation behavior, depending on the operational conditions. Nevertheless, the conventional methods used to estimate PSD (e.g., laser diffraction and/or ciclosizer) have not been designed to measure particles that tend to aggregate or disaggregate, since they include external forces (e.g., centrifugal, agitation, pumping and sonication). These forces affect the true size of the aggregates formed in a unit operation, thereby losing representativity in terms of aggregates particle size. This study presents an alternative method of measuring the size distribution of particles with aggregation behavior, particularly, by using non-invasive microscopy and image processing and analysis. The samples used have been obtained from an experimental precipitation process by applying sulfidization to treat the cyanide-copper complexes contained in a cyanidation solution. This method has been validated with statistical tools and compared with a conventional analysis based on laser diffraction. Our results show significant differences between the methods analyzed, demonstrating that image processing and analysis by microscopy is an excellent and non-invasive alternative to obtaining size distribution of aggregates in precipitation processes.

The societies of Western Europe, following the territorial delimitation of the corresponding State, have gone through different historical processes of internal homogenization. After the Peace of Westphalia (1648) the application of the principle cuius regio eius religio induced the religious homogenization of the population. Then, due to the ethnic diversity of its population, the State tried to homogenize it from the cultural point of view; it was the process of nationalization and democratization of the State. This process lead to the separation of religion from politics and from culture. After the two world wars, national reconstruction needed a foreign population: this need for labor was filled in the most developed countries by population of the countries that were least (Portuguese, Spanish, Italian ...) and also by population flows coming from the old colonies. The cultural and religious homogeneity of these countries began to lose force. With the oil crisis of the 1970s, a period of major economic fluctuations began in Europe. In those years, the second generation of the population of immigrant origin began to go to a job market that was not in good health. The religion and culture of their predecessors became autonomous resources for the reconstruction of their identity and to achieve a personal and social esteem. This process is necessarily leading States to rethink the relations between politics, culture and religion.

Floods in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous signs. In an average year in the rivers of Volyn passes from one to three floods with going beyond the limits of the floodplain. Floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The mathematical model of short-term forecasting of water level in flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed.

In this paper, we introduce a new iteration scheme, named as the S**-iteration scheme, for approximation of fixed point of the nonexpansive mappings. This scheme is faster than Picard, Mann, Ishikawa, Noor, Agarwal, Abbas, Thakur, and Ullah iteration schemes. We show the stability of our instigated scheme and give a numerical example to vindicate our claim. We also put forward some weak and strong convergence theorems for Suzuki's generalized nonexpansive mappings in the setting of uniformly convex Banach spaces. Our results comprehend, improve, and consolidate many results in the existing literature.

This paper presents an experimental scenario aimed at bridging the gap between the cities we have and the cities we need, not only in the 21^st century but also beyond, using the integrated tools of development control and holistic land development model to achieve a planner-led vision of city sustainability. Due to scathing criticisms against the development control system, the paper contends that planners as development approving officers and public interest specialists are better positioned than allied professionals to increase city sustainability through a holistic development process that benefits from the concept of strong sustainability posited by ecological economists. The paper adopts a seven-stage, 56-cell land development matrix (model) to simulate the development of the typical high-rise residential condominium in Ontario, supported with secondary data and the author’s ground experience as a planner and realtor with condominium customer service experience across Toronto and Mississauga cities between 2008 and 2017. Findings reveal that planners can seize the opportunity of being leaders of the development team to synergize the risks and value creation in land development that are key drivers of strong sustainability. The paper suggests some policy implications for averting disasters like fire hazards and terror attacks in high-rise residential buildings.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

The term Bio-Art has entered common usage to describe the interaction between the arts and the biological sciences. Although Bio-Art implies that Bio-Music would be one of its obvious sub-disciplines, the latter term has been much less frequently used. Nevertheless, there has been no shortage of projects that have brought together music and the biological sciences. Most of these projects have allowed the biological data to dictate to a large extent the sound produced, for instance the translation of genome or protein sequences into musical phrases, and therefore may be regarded as process compositions. Here I describe a Bio-Music process composition that derives its biological input from a visual representation of the expression pattern of the gene fushi tarazu in the Drosophila embryo. An equivalent pattern is constructed from the Scambi portfolio of short electronic music fragments created by Henri Pousseur in the 1950s. This general form of the resulting electronic composition follows that of the fushi tarazu pattern, while satisfying the rules of the Scambi compositional framework devised by Pousseur. The range and flexibility of Scambi make it ideally suited to other Bio-Music projects wherever there is a requirement, or desire, to build larger sonic structures from small units.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

During the last years, epigenetic processes have emerged as important factors for many neurodegenerative diseases, such as Alzheimer’s diseases (AD). These complex diseases seem to have a heritable component; however, genome-wide association studies failed to identify the genetic loci involved in the eatiology. So, how can these changes be transmitted from one gen-eration to the next? Answering this question would allow us to understand how the environ-ment can affect human populations for multiple generations and explain the high prevalence of neurodegenerative diseases, such as AD. This review pays particular attention to the relationship among epigenetics, cognition, and neurodegeneration across generations, deepening the under-standing of the relevance of heritability in neurodegenerative diseases. In fact, we highlight some recent examples of EI induced by experiences, focusing on their contribution of processes in learning and memory, to point out new targets for therapeutic interventions. Here, we first describe the prominent role of epigenetic factors in memory processing. Then, we briefly discuss aspects of EI. And ends, we summarize evidence of how epigenetic marks inherited by experi-ence and/or environmental stimuli contribute to cognitive status offspring, since better knowledge of EI can provide clues in the appearance and development of age-related cognitive decline and AD.

Manufacturing corporations has the acceptance of the Outsourcing Process (OP) to improve industrial activities as well as to archive the revenue objectives, and with this, Risk Analysis (RA) tools are constantly used to assure expected results. Failure Mode and Effect Analysis (FMEA) is one of preferred RA tools, moreover, it is proven that FMEA adds uncertainty because of the human participation at the RA, afterward it is demonstrated that Pythagorean Fuzzy Dimensional Analysis – FMEA – Value Stream Mapping (PFDA-FMEA-VSM) method removes the uncertainty in RA, likewise it aids to the stakeholders for decision making, giving more advantages improving the use of the resources on the project. This document exhibits a real case scenario in a manufacturing firm applying PFDA-FMEA-VSM method adapted for manufacturing OP. The application of PFDA-FMEA-VSM shows solid RA results, removing the human intervention uncertainty added to the risk ranking, gives advantages to the stakeholders for visualize the main risks in detailed diagram, as well as make easier to take better decisions on where to apply resources and mitigate risks during OP.

The unprecedented demand for services and applications, coupled with large network architecture calls for a radical melioration in evolving wireless networks. Massive multiple-input and multiple-out (massive MIMO) systems, small cell networks (SCN) and Heterogeneous networks (HetNet) are envisioned to meet the new quality of service (QoS) objectives of evolving networks. In this paper, we investigate massive MIMO with HetNet, where the intended macro BS signal follows Ricean fading and interfering Femto BS signals follow Rayleigh fading. Subject to the Ricean assumption, strong line-of-sight (LOS) channel exists in the coverage area, when the high power macro BS is mounted at a high altitude. Then, by exploiting matrix and stochastic geometric tools, we evaluate the signal-to-interference (SIR). And obtain QOS objectives: coverage and outage probabilities, and area spectral efficiency (ASE). Further, we investigate the role of multiple antenna system in improving the SIR. This involves massive MIMO beamforming coordination of the macro BSs through power control with max-min optimization for users at the cell-edge. Numerical results show that the coverage and outage performance converge for different user locations, pathloss and Ricean factor. Also, the monotonic increase in Ricean factor improves the SIR of a user located within coverage region. That is, a user is in an outage at a distance where the Ricean factor is very small. And, optimal macro BS antennas and Ricean factor that achieve the ASE performance guarantee a rate-fairness between the cooperating macrocells, and avoid strong Ricean channel correlation. The performance gain is dependent on Ricean factor and user location, but independent of cell size.

Cross coupling reactions have changed the way complex molecules are synthesized. In particular, Suzuki-Miyaura and Buchwald-Hartwig amination reactions have given opportunities to elegantly make pharmaceutical ingredients. Indeed, these reactions are forefront at both the stages of drug development, medicinal chemistry, and process chemistry. On one hand, these reactions have given medicinal chemists a tool to derivatize the core molecule to arrive at scaffold rapidly. On the other hand, these cross couplings have offered the process chemists a smart tool to synthesize the development candidates safely, quickly, and efficiently. Generally, the application of cross coupling reactions is broad, and this review will specifically focus on their real (pharma) world applications in large scale synthesis those appeared in last two years.

Object. Flooding in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous. In an average year floods on the rivers of Volyn region take place from one to three times which extend beyond the limits of the floodplain. The floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Methodology. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. Based on the statistical data of the Volyn Regional Center for Hydrometeorology during the 7 year period 2011-2017 about water levels of the river Styr. We conducted mathematical modeling of fluctuations of water levels within the territory of Lutsk, based on creating a partial Fourier series for discrete values of middle-ten-day water levels values. The post hydrological measurements of Styr river water levels in the territory of Lutsk located on the Shevchenko Street comply with an altitude 172.87 meters. Based on the data of short-term flood forecasting in February and March, and relief data from the Department of Architecture and Urban Development of Volyn State Administration, we conducted visualization of the results using geographic information system QGIS. Results. The results of mathematical processing were the basis for geoinformation simulation of flooded areas using remote sensing data that are publicly available. Use of statistical and geospatial data in this article has great potential for further application in modeling the processes of natural and technogenic origin. Scientific novelty. The mathematical model of short-term forecasting of water levels during the flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed. Practical significance. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The spring flood in February-March 2018, with the maximum water level 5.33 m, corresponds to an absolute mark of 178.20 m, which is forecasted in this article.

CoCr2O4 and doped lithium Co1-xLixCr2O4 chromate powder and nanoparticles were prepared by modified by sol-gel method. The morphological and structural properties of nano chromates were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and Photoluminescence (PL). Nanoparticles of doped lithium were synthesized by adding appropriate amount of cobalt nitrate, chromium nitrate, lithium nitrate and 1,2 Ethanediol as a complexing agent. The sample were heated at 105 ˚C for ten hours in oven to obtain dry gel. Calcination temperature for these samples was 700˚C for 3 hours in a furnace. The particle size of parent compound ranges from 4.4 nm to 11 nm, determined by SEM. The tendency of particles to form the aggregates with the increased annealing temperature was observed. The SEM and optical characterization of this compound has shown the sol gel derived material may be successfully used as an effective doped lithium cobalt ceramic pigment with controlled variation in structural and optical properties. SEM images showed that spherical like doped particle have diameter 33nm. From PL spectra Nano structure shows band gap 2.5ev and when we doped Lithium in it band gap decreases and become 1.19ev, which is associated to band gap transition.