There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

The production of butanol, acetone and ethanol by Clostridium acetobutylicum is a biphasic fer-mentation process. In the first phase the carbohydrate substrate is metabolized to acetic and bu-tyric acid, in the following second phase the product spectrum is shifted towards the economi-cally interesting solvents. Here we present a cascade of six continuous stirred tank reactors (CCSTR), which allows performing the time dependent metabolic phases of an ace-tone-butanol-ethanol (ABE) batch fermentation in a spatial domain. Experimental data of steady states under four operating conditions - with variations of the pH in the first bioreactor between 4.3 and 5.6 as well as the total dilution rate between 0.042 1/h and 0.092 1/h - were used to optimize and validate a corresponding mathematical model. Beyond a residence time distribution representation and substrate, biomass and product kinetics this model also includes the differen-tiation of cells between the metabolic states. Model simulations predict a final butanol product concentration of 8.2 g/L and a butanol productivity of 0.75 g/(L h) in the CCSTR operated at a pH in bioreactor 1 of 4.3 and D = 0.092 1/h, while 31 % of the cells are differentiated to the solventogenic state. Aiming at an enrichment of solvent-producing cells, a feedback loop was introduced into the cascade - sending cells from a later state of the process (bioreactor 4) back to an early stage of the process (bioreactor 2). In agreement with the experimental observations, the model accurately predicted an increase of butanol formation rate in bioreactor stages 2 and 3, resulting in an overall butanol productivity of 0.76 g/(L h) for the feedback loop cascade. The here presented CCSTR and the validated model will serve to investigate further ABE fermentation strategies for a controlled metabolic switch.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

The system design for Sustainable manufacturing is to consider both ecological and financial constraints. Manufacturing industry demands to advance in sustainable manufacturing by accounting in environment factors in it. All the factors that affect the environment need to be analyzed so that proper amendments or suggestions can be provided. To favour this, Computer aided life cycle inventory model has been presented for CNC milling and turning processes. Based on utilization of resources and stages, whole machining operation time can be divided into three phases named as process (milling or turning), idle and basic times. As parameters are different for evaluating the process times i.e. depth and width of cut in case of milling and initial and final diameters for turning, two different case studies has been presented one for each milling and turning process. Effect of material choice has been studied for different processes. Highly dense and hard materials takes more time in finishing the job due to low cutting speed and feed rates as compared to that of sot materials. In addition, face milling takes more time and consumes more power as compared to peripheral milling due to more retraction time caused by over travel distance and lower vertical transverse speeds than the horizontal transverse speed used in peripheral retraction process.

The integration of automation and process optimization within the context of AI-powered digital transformation has emerged as a pivotal strategy for organizations aiming to enhance efficiency, foster innovation, and competitiveness. This paper is devoted to present innovative contribution by providing a comprehensive structured roadmap that outlines the foundational principles necessary for the successful integration of automation and optimizing processes within the con-text of emerging AI technologies. The paper introduce a cohesive framework consisting of es-sential key pillars: Data-Driven Insights, Seamless Automation, Adaptive Learning and Contin-uous Improvement, Human-Centric Collaboration, Ethical and Responsible AI, Strategic Align-ment, Scalability, and Innovation. These pillars function as guiding principles to navigate the in-tricate landscape of automation-driven initiatives within AI-powered digital transformation. By embracing these pillars, organizations can embark on a transformative journey that maximizes the potential of automation, fosters innovation, and positions them as leaders in the ever-evolving landscape of AI-driven business operations.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Carbon Capture and Storage (CCS) stands as a pivotal technological stride toward a sustainable future, with the practice of injecting supercritical CO2 into subsurface formations having already been an established practice for enhanced oil recovery operations. The overarching objective of CCS is to protract the operational viability and sustainability of platforms and oilfields, thereby facilitating a seamless transition towards sustainable practices. This study introduces a comprehensive framework for optimizing well placements in CCS operations, employing a derivative-free method known as Bayesian optimization. The development plan is tailored for scenarios featuring aquifers devoid of flow boundaries, incorporating production wells tasked with controlling pressure buildup and injection wells dedicated to CO2 sequestration. Notably, the wells operate under group control, signifying predefined injection and production targets and constraints that must be adhered to throughout the project’s lifespan. As a result, the objective function remains invariant under specific permutations of the well locations. Our investigation delves into the efficacy of Bayesian optimization under the introduced permutation invariance. The results reveal that it demonstrates critical efficiency in handling the optimization task extremely fast. In essence, this study advocates for the efficacy of Bayesian optimization in the context of optimizing well placements for CCS operations, emphasizing its potential as a preferred methodology for enhancing sustainability in the energy sector.

Ant Colony Optimization (ACO) is a stochastic optimization algorithm inspired by the foraging behavior of ants. We investigate a simplified computational model of ACO, wherein ants sequentially engage in binary decision-making tasks, leaving pheromone trails contingent upon their choices. The quantity of pheromone left is the number of correct answers. We scrutinize the impact of a salient parameter in the ACO algorithm, specifically, the exponent $\alpha$ that governs the pheromone levels in the stochastic choice function. In the absence of pheromone evaporation, the system is accurately modeled as a multivariate nonlinear P\'{o}lya urn, undergoing a phase transition as $\alpha$ varies. The probability of selecting the correct answer for each question asymptotically approaches the stable fixed point of the nonlinear P\'{o}lya urn. The system exhibits dual stable fixed points for $\alpha\ge \alpha_c$ and a singular stable fixed point for $\alpha<\alpha_c$. When pheromone evaporates over a time scale $\tau$, the phase transition does not occur and leads to a bimodal stationary distribution of probabilities for $\alpha\ge \alpha_c$ and a monomodal distribution for $\alpha<\alpha_c$.

Machine learning forks into three main branches such as supervised learning, unsupervised learning, and reinforcement learning where reinforcement learning is much potential to artificial intelligence (AI) applications because it solves real problems by progressive process in which possible solutions are improved and finetuned continuously. The progressive approach, which reflects ability of adaptation, is appropriate to the real world where most events occur and change continuously and unexpectedly. Moreover, data is getting too huge for supervised learning and unsupervised learning to draw valuable knowledge from such huge data at one time. Bayesian optimization (BO) models an optimization problem as a probabilistic form called surrogate model and then directly maximizes an acquisition function created from such surrogate model in order to maximize implicitly and indirectly the target function for finding out solution of the optimization problem. A popular surrogate model is Gaussian process regression model. The process of maximizing acquisition function is based on updating posterior probability of surrogate model repeatedly, which is improved after every iteration. Taking advantages of acquisition function or utility function is also common in decision theory but the semantic meaning behind BO is that BO solves problems by progressive and adaptive approach via updating surrogate model from a small piece of data at each time, according to ideology of reinforcement learning. Undoubtedly, BO is a reinforcement learning algorithm with many potential applications and thus it is surveyed in this research with attention to its mathematical ideas. Moreover, the solution of optimization problem is important to not only applied mathematics but also AI.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

In this work, the deoxygenation of organic liquid products (OLP) obtained by thermal catalytic cracking of palm oil at 450 °C, 1.0 atmosphere, with 10% (wt.) Na₂CO₃ as catalyst, in multistage countercurrent absorber columns using supercritical carbon dioxide (SC-CO₂) as solvent, with Aspen-HYSYS process simulator was systematically investigated. In a previous study, the thermodynamic data basis and EOS modeling necessary to simulate the deoxygenation of OLP has been presented [Molecules 2021, 26, 4382. https://doi.org/10.3390/molecules26144382]. This work address a new flowsheet, consisting of 0₃ absorber columns, 10 expansions valves, 10 flash drums, 08 heat exchanges, 01 pressure pump, and 0₂ make-up of CO₂, aiming to improve the deacidification of OLP. The simulation was performed at 333 K, 140 bar, and (S/F) = 17; 350 K, 140 bar, and (S/F) = 38; 333 K, 140 bar, and (S/F) = 25. The simulation shows that 81.49% of OLP could be recovered and the concentrations of hydrocarbons in the extracts of absorber-01 and absorber-02 were 96.95 and 92.78% (wt.) in solvent-free basis, while the bottom stream of absorber-03 was enriched in oxygenates compounds with concentrations up to 32.66% (wt.) in solvent-free basis, showing that organic liquid products (OLP) was deacidified and SC-CO₂ was able to deacidify OLP and to obtain fractions with lower olefins content. The best deacidifying conditions was obtained at 333 K, 140 bar, and (S/F) = 17.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

This work addresses the lot-sizing and production scheduling problem of multi-stage multi-product food industrial facilities. More specifically, the production scheduling problem of the semi-continuous yogurt production process, for two large-scale Greek dairy industries, is considered. Production scheduling decisions are taken using two approaches: i) an optimization and ii) a rule-based approach, followed by a comparative study. A MILP model is applied for the optimization of short-term production scheduling of the two industries. Then, the same problems are solved using the commercial scheduling tool ScheduleProTM, which derives scheduling decisions, using simulation-based techniques and empirical rules. It is concluded that both methods, despite having their advantages and disadvantages, are suitable for addressing complex food industrial scheduling problems. The optimization-based approach leads to better results in terms of operating cost reduction. On the other hand, the complexity of the problem and the experience of production engineers and plant operators can significantly impact the quality of the obtained solutions for the rule-based approach.

A new requirement for the manufacturing companies in Industry 4.0 is to be flexible with respect to changes in demands, requiring them to react rapidly and efficiently on the production capacities. Together with the trend to use Service-Oriented Architectures (SOA), this requirement induces a need for agile collaboration among supply chain partners, but also between different divisions or branches of the same company. In order to address this collaboration challenge, we~propose a novel pragmatic approach for the process analysis, implementation and execution. This~is achieved through sets of semantic annotations of business process models encoded into BPMN 2.0 extensions. Building blocks for such manufacturing processes are the individual available services, which are also semantically annotated according to the Everything-as-a-Service (XaaS) principles and stored into a common marketplace. The optimization of such manufacturing processes combines pattern-based semantic composition of services with their non-functional aspects. This is achieved by means of Quality-of-Service (QoS)-based Constraint Optimization Problem (COP) solving, resulting in an automatic implementation of service-based manufacturing processes. The produced solution is mapped back to the BPMN 2.0 standard formalism by means of the introduced extension elements, fully detailing the enactable optimal process service plan produced. This approach allows enacting a process instance, using just-in-time service leasing, allocation of resources and dynamic replanning in the case of failures. This proposition provides the best compromise between external visibility, control and flexibility. In this way, it provides an optimal approach for business process models' implementation, with a full service-oriented taste, by implementing user-defined QoS metrics, just-in-time execution and basic dynamic repairing capabilities. This paper presents the described approach and the technical architecture and depicts one initial industrial application in the manufacturing domain of aluminum forging for bicycle hull body forming, where the advantages stemming from the main capabilities of this approach are sketched.

One of the major steps toward the industrialization of microbial product(s) is to optimize the cultivation conditions at the large scale bioreactor and successfully control the microbial behavior within large scale production environment. Statistical Design of Experiment was proven to optimize a vast number of microbial processes to achieve robustness and explore possible interactions among the variables. In this research, Taguchi Orthogonal Array was applied to optimize the cultivation condition of a newly isolated Prodigiosin-producing marine bacterial strain, Serratia AM8887, at bioreactor level. Two steps fermentation process was applied; as the productivity was scaled up from shake flask level to a bench top bioreactor (5L) and subsequently to an in-situ sterilization bioreactor system (20L) leading to a yield of 7g/L compared to 100mg/L prior to optimization confirming that; applying Taguchi experimental design is a reliable and good positive option for the optimization of biotechnological processes.. The produced pigment was purified and the chemical structure was revealed by means of Spectrophotometric, Maas Spectrum (MS), Fourier transform infrared (FT-IR), and proton nuclear magnetic resonance (1H-NMR) spectroscopy analysis. The biological activity including antibacterial, antioxidants and cytotoxicity to cancer cells line of the pigment were explored. The pigment showed very characteristic features that could helpful in food, pharmaceuticals and/or textile industries.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&amp;D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

The work safety standardization of enterprises based on the traditional work safety theory has played a significant role in reducing the number of accidents and improving work safety to some extent in China. However, some problems are coming with the work safety standardization of enterprises developing constantly in China. On the one hand, it is not combined with the actual situation of the enterprise, lacking pertinence and specificity, these defects resulted that it is not integrated with original safety production management system of enterprise and make it difficult to carry out. On the other hand, there is a lack of systematic management methods for the work safety management system of enterprise, most of enterprises only pay attention to the inspection result rather than the process control. This means after the check of the government, many enterprises will relax to carry out the system. This paper puts forward a new method for optimizing the standardization management mode of work safety based on the Viable System Model(VSM), which can solve the defects of work safety standardization of enterprises management system. An optimization model of work safety standardization based on VSM was construct for explaining the process optimization and control of work safety standardization management. It can improve the connectivity between the enterprise and the government. The conclusion of this paper can provide reference for achieving the development and optimization of work safety standardization of enterprises in China.

Industry 4.0 brings advanced technologies and automation, enabling greater productivity and efficiency. However, it also increases energy consumption and carbon emissions. Sustainable manufacturing in the era of Industry 4.0 is vital for addressing the environmental impact by minimizing resource consumption, optimizing energy efficiency, and adopting eco-friendly practices. CNC (Computer Numeric Control) 5-axis milling plays a significant role in the machining of precision molds and dies, aerospace, consumer electronics, etc. This research aims to explore the potential of the artificial intelligence (AI) technique in improving energy efficiency on CNC 5-axis milling process for sustainable manufacturing. The experiments were carried out using a CNC 5-axis milling machine with various machining parameters, toolpath planning, and dry cutting condition. Data on energy consumption of CNC 5-axis milling machine were collected, then the relationship between the machining parameters, toolpath planning, and energy consumption was analyzed and built. Furthermore, an AI-based optimization algorithm was developed that uses machine learning and optimization techniques to identify energy-efficient machining strategies. The developed algorithm was implemented within a simulation framework, the algorithm was rigorously assessed using machine learning analysis to effectively reduce energy consumption, all while ensuring the accuracy of machining result. Finally, verification experiments were carried out to evaluate the applicability and performance of the AI-based energy optimization approach on a CNC 5-axis milling machine. By integrating AI into the CNC machining process, manufacturers can achieve significant energy savings, leading to reduced carbon emissions and improved sustainability.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

This study quantified effluents generated during processing in three industry types, estimated the energy potential from the quantified effluents in form of biogas generation, and determined the economic viability of the biogas recovered. Data were procured from relevant scientific publications to quantify the effluents generated from the production processes in the industry types examined using industrial process calculations. The effluent data generated was used on the 2-module biogas energy recovery model to estimate the bioenergy recovery potential within it. Economic and financial analysis was based on cash flow comparison of all costs and benefits resulting from its activities. The effluents generated average daily biogas of 2559 Nm³/gVS, having a daily potential combined heat and power of 0.52 GWh and 0.11 GWh respectively. The Life Cycle Analysis and cost-benefit analysis show the quantity of avoided emissions from using the effluents to generate heat and power for processes, and also the profitability of the approach. Conclusively, the study shows the use of biomass effluents to generate biogas for CHP is a viable one based on the technologies of a reciprocating engine, gas turbine, microturbine, and fuel cell. However, it is recommended that the theoretical estimation be validated using a field-scale project.

The aim of this study was to determine the technical potential of the Polish Exclusive Economic Zone and to identify potential areas for offshore wind development. The paper proposes a GIS-based methodology in which a unique set of constraint-related criteria was employed to select the bests sites. These criteria included wind velocity, water depth, distance from nature conser-vation areas, distance from submarine cables and gas pipelines, distance from shipping routes, distance from fishing areas, distance from shipwrecks, distance from coastline. The Analytic Hi-erarchy Process was employed to indicate the best locations. Accordingly, the total suitable marine area of 16218.67 square kilometers was divided into three parts, in which the highly suitable area accounted for 17.55%, the moderately suitable area was 48.56%, and the marginally suitable area was 10.26%. Two different spatial configurations for the deployment of individual wind turbines were considered to assess the offshore wind potential. First configuration could accommodate 3664 turbines with overall electrical capacity equal to 54.96 GW, whereas the second one 2347 turbines with overall electrical capacity equal to 35.2 GW. The technical potential only in highly suitable areas was equal to 15.24 GW and 9.15 GW, respectively. The results were presented in the form of maps over the domain covering with spatial resolution of 1 km x 1 km.

The current work shows the optimization in the preparation of nanosized titanium carbide (TiC) in-situ through mechanical alloying (MA). Metallic titanium (Ti) powders, along with two carbon sources, carbon nanotubes (CNTs), and stearic acid (SA), were used to reduce the particle size using a high-energy Spex800 mill. The combined use of 2 wt % of these carbon sources and n-heptane as a liquid process control agent (PCA) proved crucial in generating nanoscale powder composites through a simple and scalable synthesis process within a 4-hour timeframe. The use of 20 wt % of both carbon sources was compared to determine the ability of CNTs to form carbides and the decomposition of PCAs during mechanical milling. The result reveals structures like nanoblocks and nanolumps with and important size reduction. The structure and morphology of the composites and starting materials were evaluated through x-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

The article presents the results of testing the conditions of closing foundry voids during the hot forging operation of an ingot made of zirconium with 1% Nb alloy and use of the physical and numerical modelling, which is a continuation of research presented in a previous thematically related article published in the journal Materials. The study of the impact of forging operation parameters on the rheology zirconium with 1% Nb alloy was carried out on the Gleeble 3800 device. Using the commercial FORGE®NxT 2.1 program, a numerical analysis of the influence of thermo-mechanical parameters of the hot elongation operation in trapezoidal flat and rhombic trapezoidal anvils on the closure offoundry voids was performed. The analysis of the obtained test results was used to formulate recommendations on the technology of hot forging and the geometry of anvils, which ensure the closure foundry voids during the operation of hot forging

Due to the high computational burden and the high nonlinearity of the responses, crashworthiness optimizations are notoriously hard-to-solve challenges. Among various approaches, methods like the Successive Response Surface Method (SRSM) have stood out for their efficiency in enhancing baseline designs within a few iterations. However, these methods have limitations that restrict their application. Their minimum iterative resampling required is often computationally prohibitive. Furthermore, surrogate models are conventionally constructed using Polynomial Response Surface (PRS), a method that is poorly versatile, prone to overfitting, and incapable of quantifying uncertainty. Furthermore, the lack of continuity between successive response surfaces results in suboptimal predictions. This paper introduces the Multi-Fidelity Successive Response Surface (MF-SRS), a Gaussian process-based method, which leverages a nonlinear multi-fidelity approach for more accurate and efficient predictions compared to SRSM. After initial testing on synthetic problems, this method is applied to a real-world crashworthiness task: optimizing a bumper crossmember and crash box system. Results, benchmarked against SRSM and the Gaussian Process Successive Response Surface (GP-SRS) – a single-fidelity Gaussian process-driven extension of SRSM, show that MF-SRS offers distinct advantages. Specifically, it improves upon the specific energy absorbed optimum value achieved by SRSM by 14.1 %, revealing its potential for future applications.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

Plasma technology shows tremendous potential for revolutionizing oncology research and treatment. Reactive oxygen and nitrogen species, electromagnetic emissions generated through gas plasma jets, have attracted significant attention due to their selective cytotoxicity towards cancer cells. To leverage the full potential of plasma medicine, researchers have explored the use of mathematical models and various subsets of machine learning, such as reinforcement learning, and deep learning. This review emphasizes the significant application of AI algorithms in the adaptive plasma system, paving the way for precision and dynamic cancer treatment. Realizing the full potential of AI in plasma medicine, requires research efforts, data sharing and interdisciplinary collaborations. Unravelling the complex mechanisms, developing real-time diagnostics, and optimizing AI models will be crucial to harness the true power of plasma technology in oncology. The integration of personalized and dynamic plasma therapies, alongside AI and diagnostic sensors, presents a transformative approach to cancer treatment with the potential to improve outcomes globally.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

The fifth Industrial revolution (I5.0) prioritizes resilience and sustainability, integrating cognitive cyber-physical systems and advanced technologies to enhance machining processes. Numerous research studies have been conducted to optimize machining operations by identifying and reducing the sources of uncertainty and estimating the optimal cutting parameters. Virtual modeling and Tool Condition Monitoring (TCM) methodologies have been developed to assess the cutting states during machining processes. With a precise estimation of cutting states, the safety margin necessary to deal with the uncertainties can be reduced, resulting in improved process productivity. This paper reviews the recent advances in high-performance machining systems with a focus on the cyber-physical models developed for the cutting operation of difficult-to-cut materials using cemented carbide tools. An overview of the literature and background on the advances in the offline and online process optimization approaches have been presented. Process optimization objectives such as tool life utilization, dynamic stability, enhanced productivity, improved machined part quality, and reduced energy consumption and carbon emissions are independently investigated for the offline and online optimization methods. Addressing the critical objectives and constraints prevalent in industrial applications, the paper explores the challenges and opportunities inherent in developing a robust cyber-physical optimization system

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

Highly flexible manufacturing systems require continuous run-time (self-) optimization of processes with respect to various parameters, e.g. efficiency, availability, energy consumption etc. A promising approach for achieving (self-) optimization in manufacturing systems is the usage of the context sensitivity approach. Thereby the Cyber-Physical Systems play an important role as sources of information to achieve context sensitivity. In this paper it is demonstrated how context sensitivity can be used to realize a holistic solution for (self-) optimization of discrete flexible manufacturing systems, by making use of Cyber-Physical System integrated in manufacturing systems/processes. A generic approach for context sensitivity, based on self-learning algorithms, is proposed aiming at a various manufacturing systems. The new solution is propos encompassing run-time context extractor and optimizer. Based on the self-learning module both context extraction and optimizer are continuously learning and improving their performance. The solution is following Service Oriented Architecture principles. The generic solution is developed and then applied to two very different manufacturing processes. This paper proposes a holistic solution to achieve context sensitivity for Flexible Manufacturing Systems, whereby the knowledge created by applying the context sensitivity approach can be used for (self-) optimization of manufacturing processes.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

Poso regency, Central Sulawesi, Indonesia, has a coastal area that has marine tourism potential to be developed. It is expected that marine tourism can bring socio-economic impact to the com-munity. This research was conducted with the objective of assessing the suitability of the area to be developed as a marine and coastal tourism site to provide benefits to the coastal community. Hydrodynamic model will be used in this research as coastal area mapping. As an approach, Analysis Hierarchy Process (AHP) is utilized whose parameters consist of depth, coast type, coast width, brightness, current speed, water base materials, observation of dangerous biota and availability of fresh water. Based on the overall mapping area of 98,644 ha, the research results show that the area that can be utilized is 7,979 ha with a very suitable category, while there is an area of 1,045 ha which can still be classified in the appropriate category.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

Object. Flooding in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous. In an average year floods on the rivers of Volyn region take place from one to three times which extend beyond the limits of the floodplain. The floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Methodology. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. Based on the statistical data of the Volyn Regional Center for Hydrometeorology during the 7 year period 2011-2017 about water levels of the river Styr. We conducted mathematical modeling of fluctuations of water levels within the territory of Lutsk, based on creating a partial Fourier series for discrete values of middle-ten-day water levels values. The post hydrological measurements of Styr river water levels in the territory of Lutsk located on the Shevchenko Street comply with an altitude 172.87 meters. Based on the data of short-term flood forecasting in February and March, and relief data from the Department of Architecture and Urban Development of Volyn State Administration, we conducted visualization of the results using geographic information system QGIS. Results. The results of mathematical processing were the basis for geoinformation simulation of flooded areas using remote sensing data that are publicly available. Use of statistical and geospatial data in this article has great potential for further application in modeling the processes of natural and technogenic origin. Scientific novelty. The mathematical model of short-term forecasting of water levels during the flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed. Practical significance. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The spring flood in February-March 2018, with the maximum water level 5.33 m, corresponds to an absolute mark of 178.20 m, which is forecasted in this article.

Floods in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous signs. In an average year in the rivers of Volyn passes from one to three floods with going beyond the limits of the floodplain. Floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The mathematical model of short-term forecasting of water level in flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed.

High-strength low-alloy steels (HSLAs) are widely used in the structural body components of many domestic motor vehicles owing to their better mechanical properties and greater resistance. The real production process of HSLA steelmaking can be regarded as a model that builds on the relationship between process parameters and product quality attributes. A surrogate modeling method is used, and the resulting production process model can be applied to predict the optimal manufacturing process parameters. We used different methods in this paper to build such a surrogate model, including linear regression, random forests, support vector regression, multilayer perception, and a simplified VGG model. We then applied three bio-inspired search algorithms, namely particle swarm optimization, the artificial bee colony algorithm, and the firefly algorithm, to search for the optimal controllable manufacturing process parameters. Through experiments on 9,000 test samples used for building the surrogate model, and 299 test samples for making the optimal process parameter selection, we found that the combination of a simplified VGG model and the firefly algorithm was the most successful at reaching a success rate of 100%—in other words, when the product quality attributes of all test samples satisfy the mechanical requirements of the end products.

In this work, the thermodynamic data basis and EOS modeling necessary to simulate the fractionation of organic liquid products (OLP), a liquid reaction product obtained by thermal catalytic cracking of palm oil at 450ºC, 1.0 atmosphere, with 10% (wt.) Na2CO3 as catalyst, in multistage countercurrent absorber/stripping columns using SC-CO2 as solvent, with Aspen-Hysys was systematically investigated. The chemical composition of OLP was used to predict the physical (), thermo-physical properties (Tb, Tc, Pc, Vc), and acentric factor () of all the compounds present in OLP by applying the group contribution methods of Marrero-Gani, Han-Peng, Marrero-Pardillo, Constantinou-Gani, Joback and Reid, and Vetere. The RK-Aspen (EOS) used as thermodynamic fluid package, applied to correlate the experimental phase equilibrium data of binary systems organic liquid products compounds (OLP)-i/CO2 available in the literature. The group contribution methods selected based on the lowest relative average deviation by computing Tb, Tc, Pc, Vc, and . For n-alkanes, the method of Marrero-Gani selected for the prediction of Tc, Pc and Vc, and that of Han-Peng for . For alkenes, the method of Marrero-Gani selected for the prediction of Tb and Tc, Marrero-Pardillo for Pc and Vc, and Han-Peng for . For unsubstituted cyclic hydrocarbons, the method of Constantinou-Gani selected for the prediction of Tb, Marrero-Gani for Tc, Joback for Pc and Vc, and the undirected method of Vetere for . For substituted cyclic hydrocarbons, the method of Constantinou-Gani selected for the prediction of Tb and Pc, Marrero-Gani for Tc and Vc, and the undirected method of Vetere for . For aromatic hydrocarbon, the method of Joback selected for the prediction of Tb, Constantinou-Gani for Tc and Vc, Marrero-Gani for Pc, and the undirected method of Vetere for . The regressions show that RK-Aspen EOS was able to describe the experimental phase equilibrium data for all the binary pairs undecane-CO2, tetradecane-CO2, pentadecane-CO2, hexadecane-CO2, octadecane-CO2, palmitic acid-CO2, and oleic acid-CO2, showing average absolute deviation (AADx) between 0.8% and 1.25% for the liquid phase and (AADy) between 0.01% to 0.66% for gaseous phase.

Friction stir welding (FSW) is a solid state welding process for joining metallic alloys and dissimilar metals. It has emerged as an alternative technology for welding high strength alloys that are difficult to join with conventional techniques. FSW is used to produce products with better mechanical properties. Now a days aluminum alloys have been widely used in several industrial applications such as aerospace, marine, automobile and commercial applications due to their light weight structure, better mechanical properties and high corrosion resistance.In this work, three welding parameters such as spindle speed, welding speed and plunge depth were considered for friction stir welding. FSW was carried out between dissimilar aluminum alloy plates (AA6061 and AA 8011) to produce butt joint.A Box-Behnken design with three factors and three levels was chosen to minimize the number of experimental conditions .The tensile strength and hardness of the welded regions were evaluated. The optimum level settings and the major parameters that influence the joint strength were obtained by Box-Behnken design.

This paper presents a new method of process parameters optimization, adequate for 3D printing of PLA (Polylactic Acid) components. The authors developed a new Hybrid Manufacturing Equipment (HME), suitable for producing complex parts made from a biodegradable thermoplastic polymer, for environmental sustainability. Our new HME equipment is producing PLA parts by both additive and subtractive techniques, with the aim of obtaining accurate PLA components with a good surface quality. A design of experiments has been applied for optimization purposes. The following manufacturing parameters were analyzed: rotation of the spindle, cutting depth, feed rate, layer thickness, nozzle speed, and surface roughness. Linear regression models and neural network models were developed to improve and predict the surface roughness of the manufactured parts. A new test part was designed and manufactured from PLA, to validate the new mathematical models, which can now be applied for producing complex parts made from polymer materials.

Evaporation is one of the main processes in the hydrological cycle, and it is one of the most critical factors in agricultural, hydrological, and meteorological studies. Due to the interactions of multiple climatic factors, the evaporation is a complex and nonlinear phenomenon; therefore, the data-based methods can be used to have precise estimations of it. In this regard, in the present study, Gaussian Process Regression (GPR), Nearest-Neighbor (IBK), Random Forest (RF) and Support Vector Regression (SVR) were used to estimate the pan evaporation (PE) in the meteorological stations of Golestan Province, Iran. For this purpose, meteorological data including PE, temperature (T), relative humidity (RH), wind speed (W) and sunny hours (S) collected from the Gonbad-e Kavus, Gorgan and Bandar Torkman stations from 2011 through 2017. The accuracy of the studied methods was determined using the statistical indices of Root Mean Squared Error (RMSE), correlation coefficient (R) and Mean Absolute Error (MAE). Furthermore, the Taylor charts utilized for evaluating the accuracy of the mentioned models. The outcome indicates that the optimum state of Gonbad-e Kavus, Gorgan and Bandar Torkman stations, Gaussian Process Regression (GPR) with the error values of 1.521, 1.244, and 1.254, the Nearest-Neighbor (IBK) with error values of 1.991, 1.775, and 1.577, Random Forest (RF) with error values of 1.614, 1.337, and 1.316, and Support Vector Regression (SVR) with error values of 1.55, 1.262, and 1.275, respectively, have more appropriate performances in estimating PE. It found that GPR for Gonbad-e Kavus Station with input parameters of T, W and S and GPR for Gorgan and Bandar Torkmen stations with input parameters of T, RH, W, and S had the most accurate performances and proposed for precise estimation of PE. Due to the high rate of evaporation in Iran and the lack of measurement instruments, the findings of the current study indicated that the PE values might be estimated with few easily measured meteorological parameters accurately.

This paper presents a methodology for determining the sensitivity of the main air flow directions in ventilation subnetworks to changes of aerodynamic resistance and of air density in mine workings. Formulae for determination of the sensitivity of the main subnetwork air flows by establishing the degree of dependency of the air volume stream in a given working on the variations in resistance or air density of other workings of the network have been developed. They have been implemented in the VentGraph mine ventilation network simulator. This software, widely used in Polish collieries provides an extended possibility to predict the process of ventilation, air distribution and, in the case of underground fire, also the spread of combustion gasses. The new method facilitates assessment by mine ventilation services of the stability of ventilation systems in exploitation areas and determine of the sensitivity of the main subnetwork air flow directions to changes of aerodynamic resistance and air density. Recently in some Polish collieries new longwalls are developed in seams located deeper then the bottom of the intake shaft. Such solution is called “exploitation below the level of access” or “sublevel”. The new approach may be applied to such developments to assess the potential of changes of direction and air flow rates. In addition, interpretation of the developed sensitivity indicator is presented. While analyzing air distributions for sublevel exploitation, application of current numerical models for calculations of the distribution results in tangible benefits, such as the evaluation of the safety or risk levels for such exploitation. Application of the VentGraph computer program, and particularly the module POŻAR (fire) with the newly developed options, enables an additional approach to the sensitivity indicator in evaluating air flow safety levels for the risks present during exploitation below the level of the intake shaft. The analyses performed and examples presented enabled useful conclusions in mining practice to be drawn.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

For a long time, a company's Product Development Process (PDP) was seen as supporting the operations department, although PDP decisions and mistakes have a considerable impact on market performance. This is critical even in agriculture where bad habits and practices in the PDP can lead rural producers to great losses. Therefore, this research investigated the effect on the market performance of rural products (banana) in the southern region of Brazil, based on two analyses: (i) how sustainability practices support the PDP phases and (ii) how the phases of the Product Life Cycle Assessment (LCA) mediate sustainability practices and PDP phases. This study presents a quantitative analysis using Confirmatory Factor Analysis (CFA) and hierarchical ordinary least squares (OLS) regression of data obtained from a survey of 110 rural producers who directly participate in the banana production and planning process in southern Brazil. Our results shows that sustainability practices support the PDP, and we confirm that the product development and post-development phase has an effect on market performance. In addition, we identified that in the pre-development phase of the PDP, dealing with rural products (bananas), the maturity stage of the LCA mediates sustainability. In the PDP development phase, we concluded that rural families that develop economic and environmental practices with their products in the market growth phase may have reduced results. As for the post-development phase of the PDP, we conclude that when companies invest in environmental and social practices, there is a complete mediation of the effect, where these practices lose strength if the product is in the introduction and maturity phases in the market. As originality, our study contributed to demonstrate value on the product life cycle for the product development process in agriculture using sustainability practices through a systemic approach, filling the gap in the literature due to the lack of research on these areas seen in an integrated way.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

The weight loss process variables of alkali-treated micropolyester woven fabric were optimized and reported in this study. The grey relational analysis (GRA) with the help of the Taguchi technique was efficiently used to optimize the key variables of this process. The caustic soda concentration, treatment temperature, and weight loss machine speed were considered the control or design parameters. The weight reduction percentage, air permeability, tensile strength, and thermal resistance of alkali-treated woven polyester fabrics were also considered as responses in this study. The experiments were implemented according to a 33 full factorial design. The levels of the control parameters which yield the maximum weight reduction, tensile strength, air permeability, and minimum thermal resistance of the treated polyester fabrics were found to be NaOH concentration and treatment temperature with the highest levels, and machine speed with the lowest level. This means that a 27% caustic soda concentration, treatment temperature of 125 OC, and machine speed of 40 m/min exhibited the optimum properties of the treated micropolytester fabrics. It is also proved that the treatment temperature is the most influential factor affecting the micropolyester fabric’s properties. The confirmation test which was carried out in this study confirmed that the GRA improved the alkali-treated polyester fabric properties.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

Communication is indispensable for today's lifestyle, and thanks to technology, millions of people can communicate as quickly as possible. The effect of this breakthrough has transformed organizations to the degree that they generate billions of emails daily to facilitate their operations. There is implicit information behind this vast corpus of human-generated content that can be mined and used for their benefit. This paper tries to address the opportunity that email logs can bring to organizations and propose an approach to discover process models by combining supervised text classification and process mining. This framework consists of two main steps, text classification, and process mining. First, Emails will be classified with supervised machine learning, and to mine, the processes fuzzy Miner is used. To further investigate the application of this framework, we also applied this framework over a real-life dataset from a case study organization.

Improving the quality of petroleum products and refining processes through the use of artificial intelligence and machine learning techniques is the topic of this article. It shows that expert knowledge and conventional empirical models can't get you where you want to go in a refining process. To effectively capture complex interactions and forecast fuel qualities, machine learning techniques such as principal component analysis (PCA), support vector machines (SVM), artificial neural networks (ANN), and partial least squares (PLS) are suggested. Gasoline and other petroleum products, as well as property prediction, process control, product quality, and operational efficiency in refineries, can all be improved with the help of machine learning applied to spectral or distillation curve data. An exciting new direction in optimizing operations, meeting environmental norms, and precisely estimating gasoline quality is offered by advanced machine learning algorithms.

Contemporary financial systems, despite their inherent complexity and resilience, face significant challenges related to transparency, efficiency, and security. Notable deficiencies in transparency and emerging security vulnerabilities underscore the pressing need for innovative solutions in current financial practices. Hence, this paper introduces a financial distribution system based on a consortium blockchain. Given organizations’ preference for keeping sensitive data private, the partially decentralized nature of consortium blockchains plays a pivotal role in the proposed system’s architecture. Moreover, within this system, the proposed smart contract serves a dual role. It functions not only as a transactional tool but also as a specialized solution designed to improve transactional procedures. Its multifaceted capabilities include ensuring data accuracy, facilitating swift execution, and ensuring adherence to regulatory requirements within the dynamic financial distribution landscape. Through rigorous testing and empirical analysis utilizing the Hyperledger Besu platform, it has been observed that the performance of the proposed system surpasses traditional blockchain frameworks. The results unequivocally demonstrate the proposed system’s proficiency in handling high-frequency financial transactions with minimal computational burden.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Process (or business process) management systems fulfill defining, executing, monitoring and managing process models deployed on process-aware enterprises. Accordingly, the functional formation of the systems is made up of three subsystems such as modeling subsystem, enacting subsystem and mining subsystem. In recent times, the mining subsystem has been becoming an essential subsystem. Many enterprises have successfully completed the introduction and application of the process automation technology through the modeling subsystem and the enacting subsystem. According as the time has come to the phase of redesigning and reengineering the deployed process models, from now on it is important for the mining subsystem to cooperate with the analyzing subsystem; the essential cooperation capability is to provide seamless integrations between the designing works with the modeling subsystem and the redesigning work with the mining subsystem. In other words, we need to seamlessly integrate the discovery functionality of the mining subsystem and the analyzing functionality of the modeling subsystem. This integrated approach might be suitable very well when those deployed process models discovered by the mining subsystem are complex and very large-scaled, in particular. In this paper, we propose an integrated approach for seamlessly as well as effectively providing the mining and the analyzing functionalities to the redesigning work on very large-scale and massively parallel process models that are discovered from their enactment event logs. The integrated approach especially aims at analyzing not only their structural complexity and correctness but also their animation-based behavioral properness, and becomes concretized to a sophisticated analyzer. The core function of the analyzer is to discover a very large-scale and massively parallel process model from a process log dataset and to validate the structural complexity and the syntactical and behavioral properness of the discovered process model. Finally, this paper writes up the detailed description of the system architecture with its functional integration of process mining and process analyzing. And more precisely, we excogitate a series of functional algorithms for extracting the structural constructs as well as for visualizing the behavioral properness on those discovered very large-scale and massively parallel process models. As experimental validation, we apply the proposed approach and analyzer to a couple of process enactment event log datasets available on the website of the 4TU.Centre for Research Data.

With the advances in industry and commerce, passengers have become more accepting of environmental sustainability issues; thus, more people now choose to travel by bus. Government administration constitutes an important part of bus transportation services as the government gives the right-of-way to transportation companies allowing them to provide services. When these services are of poor quality, passengers may lodge complaints. The increase in consumer awareness and developments in wireless communication technologies have made it possible for passengers to easily and immediately submit complaints about transportation companies to government institutions, which has brought drastic changes to the supply-demand chain comprised of the public sector, transportation companies, and passengers. This study proposed the use of big data analysis technology including systematized case assignment and data visualization to improve management processes in the public sector and optimize customer complaint services. Taichung City, Taiwan was selected as the research area. There, the customer complaint management process in public sector was improved, effectively solving such issues as station-skipping, allowing the public sector to fully grasp the service level of transportation companies, improving the sustainability of bus operations, and supporting the sustainable development of the public sector-transportation company-passenger supply chain.

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

In this paper, we study a generalised CIR process with externally-exciting and self-exciting jumps, and focus on the distributional properties and applications of this process and its aggregated process. The first and second moments of this jump-diffusion process are used to calculate the insurance premium based on mean-variance principle. The Laplace transform of the aggregated process is derived, and this leads to an application for pricing default-free bonds which could capture the impacts of both exogenous and endogenous shocks. Illustrative numerical examples and comparisons with other models are also provided.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

The contribution deals with the selection of progressive methods and technologies to improve the management of production processes in the industrial area. The first chapter of the contribution summarises the theoretical starting points for the management of production processes and their progressive concepts. Chapter 2 deals with the analysis of the current state of play in the use of methods and technologies in production management and summarise its problem areas. Chapter 3 presents the design of a system for selecting the appropriate method and technology to improve the management of the production process. The system presented is designed from data collection blocks, a benchmark for the performance of industrial enterprises' production processes, and data mining to gain knowledge of the impact of the methods and technologies used on the performance of production processes. The last block of the system allows the presentation of the obtained results, which sets out the recommendation for the choice of progressive method and technology. The system is partially verified in the last chapter of the contribution.

This paper describes the state of the art and future opportunities for process design and sustainable development. In the Introduction the main global megatrends and European Union's response to two of them, the European Green Deal, are presented. The organization of professionals in the field, their conferences and publications support the two topics. A brief analysis of the published documents in the two most popular databases shows that the environmental dimension predominates, followed by an economic one, while the social pillar of sustainable development is undervalued. The main design tools for sustainability are described. As an important practical case, the European chemical and process industries are analyzed and their achievements in sustainable development are highlighted; in particular, their strategies are presented in more detail. The conclusions cover the most urgent future development areas of the process industries, carbon capture with utilization or storage, process analysis, simulation, synthesis and optimization tools; zero waste, circular economy and resource efficiency already play an important role. However, more profound changes are needed in the coming decades, including a shift away from growth with changes in habits, lifestyles and business models. Lifelong education for sustainable development will play a very important role in the growth of democracy and happiness instead of consumerism and neoliberalism.

The Process Algebra model has been shown to provide an alternative mathematical framework for non-relativistic quantum mechanics (NRQM). It reproduces the wave functions of non-relativistic quantum mechanics to a high degree of accuracy. It posits a fundamental level of finite, discrete events upon which the usual entities of NRQM supervene. It has been suggested that the Process Algebra model provides a true completion of NRQM, free of divergences and paradoxes, with causally local information propagation, contextuality and realism. Arguments in support of these claims have been mathematical. Missing has been an ontology of this fundamental level from which the formalism naturally emerges. In this paper it is argued that information and information flow provides this ontology. Higher level constructs such as energy, momentum, mass, spacetime, are all emergent from this fundamental level.

During the last decades, the production systems have developed different strategies to increase their competitiveness in the global market. In a manufacturing and services systems, Lean Manufacturing has been consolidated through the correct implementation of its tools. The present paper presents a case study developed in a Food Packer company where a Simulation Model was considered as an alternative to reduce the waste time generated by the poor distribution of operations and transportation areas for a product within the factory. As a matter of fact, the company has detected problems on the layout distribution that prevents to fulfill the market demand. In addition, the principal aim was to create a simulation model to test different hypothetical scenarios and alternative designs for the layout distribution without modifying its facilities. Moreover, the implemented methodology was based on classical models of simulation projects and a compendium of the manufacturing systems optimization by simulation process used during the last ten years. Also, a mathematic model supported by the Promodel ® simulation software was developed considering the company characteristics; along with the model development, it was possible to compare the production system performance from the percentage of used locations, the percentage of resources utilization, the number of finished products, and the level of Work in Process (WIP). Finally, the verification and validation stages were performed before running the scenarios in the real production area. The results generated by the implementation of the project represent an increase of 68% in the production capacity and a reduction of 5% in the WIP. In addition, both outcomes are associated with the resources management, which were reassigned to other production areas.

The importance of oxygen in the winemaking process is widely known, as it affects the chemical aspects and therefore the organoleptic characteristics of the final product. Hence, it is evident the usefulness of a continuous and real-time measurements of the levels of oxygen in the various stages of the winemaking process, both for monitoring and for control. The WOW project has focused on the design and the development an innovative device for monitoring the oxygen levels in wine. This system is based on the use of an optical fiber to measure the luminescent lifetime variation of a reference metal/porphyrin complex, which decays in presence of oxygen. The developed technology results in a high sensitivity and low cost sensor head that can be employed for measuring the dissolved oxygen levels at several points inside a wine fermentation or aging tank. This system can be complemented with dynamic modeling techniques to provide predictive behavior of the nutrient evolution in space and time given few sampled measuring points for both process monitoring and control purposes. The experimental validation of the technology has been first performed in a controlled laboratory setup to attain calibration and study sensitivity with respect to different photo-luminescent compounds and alcoholic or non-alcoholic solutions, and then in an actual case study during a measurement campaign at a renown Italian winery.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

This contribution illustrates the training evaluation system developed within the Master’s Program in Family and Community Mediation at Università Cattolica del Sacro Cuore in Milan. This is an interim evaluation, which focuses on the training process and which considers fundamental the collaboration with the subjects of the training. The peculiarity of this work concerns the possibility of inserting research within the training process, following a logic of mutual enrichment both in terms of content and learning. The contribution illustrates in detail the outcome and the process evaluation system, defining the perspective, the objectives, and the methodology of implementation. In particular, the outcome evaluation focuses on the distal and proximal outcomes of the training, while the process analysis focuses on the dynamics within the group of participants. Although further evaluations involving different training groups and other training processes are needed, this training evaluation system allows to shed light on both the topic and the context in which training is delivered. The integration between different points of view and several levels of analysis allows the researchers to deepen the individual path of each participant as well as to have feedbacks on the progress of the training group as a whole.

This article describes the Analytic Hierarchy Process (AHP) method which can be calculated by several methods. The AHP method is essential for the managerial decision-making to recognize which method is efficient for the calculation and to determine the proper order of criteria. In the article there are included methods that can be used in order to calculate the matrix in the AHP process for setting criteria such as Geometric mean, Arithmetic mean, Row sum of the adjusted the Saaty matrix, Reverse sums of the Saaty matrix columns and Row sums of the Saaty matrix. The paper is focused on the accuracy of the methods used. The results show that the most accurate method is the Saaty method, and the second most accurate method is the geometric mean in order to determine the ranking. This method is easier to use when the same order is achieved as in the Saaty method, followed by Geometric mean, which is favourable for fast and easy determination of alternatives using in the AHP process. The survey carried out among managers graduated from Universities and Colleges in Slovakia showed that the respondents considered the Saaty method as the most complex and also the most difficult method and the geometric mean average method the simplest method. 44% of respondents stated that they are capable to use a program to calculate the AHP. 46% of respondents said they had experience with some method related to the managerial decision-making process. 72% of managers regarded as important to manage some method for decision-making in their managerial position.

In the concept of the process signature, the relationship between a material load and the modification remaining in the workpiece is used to better understand and optimize manufacturing processes. The basic prerequisite for this is to be able to measure the loads occurring during the machining process in the form of mechanical deformations. Speckle photography is suitable for this in-process measurement task and is already used in a variety of ways for in-plane deformation measurements. The shortcoming of this fast and robust measurement technique based on image correlation techniques is that out-of-plane deformations in the direction of the measurement system cannot be detected and increases the measurement error of in-plane deformations. In this paper, we investigate a method that infers local out-of-plane motions of the workpiece surface from the decorrelation of speckle patterns and is thus able to reconstruct three-dimensional deformation fields. The implementation of the evaluation method enables a fast reconstruction of 3D deformation fields, so that the in-process capability remains given. First measurements in a deep rolling process show that dynamic deformations underneath the die can be captured and demonstrate the suitability of the speckle method for manufacturing process analysis.

Since their introduction, process trees have been frequently used as a process modeling formalism in many process mining algorithms. A process tree is a (mathematical) tree-based model of a process, in which internal vertices represent behavioral control-flow relations and leaves represent process activities. Translation of a process tree into a sound Workflow net is trivial; however, the reverse is not the case. Simultaneously, an algorithm that translates a WF-net into a process tree is of great interest, e.g., the explicit knowledge of the control-flow hierarchy in a WF-net allows one to reason on its behavior more easily. Hence, in this paper, we present such an algorithm, i.e., it detects whether a WF-net corresponds to a process tree, and, if so, constructs it. We prove that, when the algorithm finds a process tree, the language of the process tree is equal to the language of the original WF-net. The experiments conducted show that the algorithm’s corresponding implementation has a quadratic time complexity in the size of the WF-net. Furthermore, the experiments show strong evidence of process tree re-discoverability.

Atmospheric correction is the processes of converting radiance measured at a spectral 1 sensor to the reflectance of the materials in a multispectral or hyperspectral image. This is an 2 important step for detecting or identifying the materials present in the pixel spectra. We present 3 two machine learning models for atmospheric correction trained and tested on 100,000 batches of 40 4 reflectance spectra converted to radiance using MODTRAN, so the machine learning model learns 5 the radiative transfer physics from MODTRAN. We created a theoretically interpretable Bayesian 6 Gaussian process model and a deep learning autoencoder treating the atmosphere as noise. We 7 compare both methods for estimating gain in the correction model to the well-know QUAC method 8 of assuming a constant mean endmember reflectance. Prediction of reflectance using the Gaussian 9 process model outperforms the other methods in terms of both accuracy and reliability.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Process model discovery covers different methodologies to mine a process model from traces of process executions, and is gaining an important role in Artificial Intelligence research. Current approaches in the area, with few exceptions, focus on determining a model of the flow of actions only. However, in several contexts, (i) restricting the attention to actions is quite limitative, since the effects of such actions have to be analysed, too, and (ii) traces provide additional pieces of information, in the form of states (i.e., values of parameters possibly affected by the actions): for instance, in several medical domains traces include both actions and measurements of patients’ parameters. In this paper, we propose AS-SIM (Action-State SIM), the first approach able to mine a process model which comprehends two distinct classes of nodes, to capture both actions and states.

Companies have been increasing the amount of data that they collect from their systems and processes, considering the decrease in the cost of memory and storage technologies in recent years. The emergence of technologies such as Big Data, Cloud Computing, E-Science, and the growing complexity of information systems made evident that traceability and provenance are promising approaches. Provenance has been successfully used in complex domains, like health sciences, chemical industries, and scientific computing, considering that these areas require a comprehensive semantic traceability mechanism. Based on these, we investigate the use of provenance in the context of Software Process (SP) and introduce a novel approach based on provenance concepts to model and represent SP data. It addresses SP provenance data capturing, storing, new information inferencing and visualization. The main contribution of our approach is PROV-SwProcess, a provenance model to deal with the specificities of SP and its ability in supporting process managers to deal with vast amounts of execution data during the process analysis and data-driven decision-making. A set of analysis possibilities were derived from this model, using SP goals and questions. A case study was conducted in collaboration with a software development company to instantiate the PROV-SwProcess model (using the proposed approach) with real-word process data. This study showed that 87.5% of the analysis possibilities using real data was correct and can assist in decision-making, while 62.5% of them are not possible to be performed by the process manager using his currently dashboard or process management tool.

: The objective of this work is to elucidate the role of partnerships and the number of partners necessary for lead user innovation outcomes. Lead user theory identifies these users as being ahead of market trends and experiencing significant benefits from innovating. So far, most lead user research has concentrated on firms and not individual lead users’ perspective. Data were obtained using a quantitative design during which 321 respondents participated. The SPSS software was used to analyze the data and determine significance. These findings indicate a connection between number of partners and lead user innovation success. This demonstrates that number of partners is significant in determining the success or failure of an innovation. This study provides empirical evidence that the number of partners is an essential factor that influences the success of innovation, and establishes the absolute numbers for achievement of successful innovation. Future studies must investigate the possible implications of integrating the partner variables with other characteristics of the lead user.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

Injection molding is one of the most common and effective manufacturing processes used to produce plastic products and impacts industries around the world. However, injection molding is a complex process that requires careful consideration of several key control variables. These variables and how they are utilized greatly affect the resulting parts of any molding operation. The bounds of the acceptable values of each control process variable or CPV must be analyzed and delimited to ensure manufacturing success and produce injected molded parts efficiently and effectively. One such method in which the key CPV of an injection molding operation can be delimited is through the development of a process window. Once developed, operating CPV at values inside the boundaries of the window or region will allow for the consistent production of parts that comply with the desired performance measures (PM), promoting a stable manufacturing process. This work proposes a method to experimentally develop process windows and illustrates the methodology with a specific molding operation.

The innate immune system is the first line of defense against pathogens. It’s composition includes barriers, mucus and other substances as well as phagocytic and other cells. The purpose of the paper is to analyze in general grounds the immune system and the body immunity to cancer. Simple ideas and the qualitative theory of differential equations are used along with general principles such as the minimization of the pathogen load and economy of resources. In the simplest linear model, the annihilation rate of pathogens in any tissue should be greater than the pathogen’s average rate of growth. When nonlinearities are added, a reference value for the number of pathogens is set, and a stability condition emerges, which relates strength of regular threats, barrier height and annihilation rate. On the other hand, in cancer immunity, the linear model leads to an expression for the lifetime risk, which accounts for both the effects of carcinogens (endogenous or external) and the immune response. The stability condition allows a comparison of immunity in different tissues. The way the tissue responds to an infection shows a correlation with the way it responds to cancer. These statements are formulated at the qualitative level, but may and deserve to be quantitatively checked.

Semisolid casting of Aluminum alloys is growing. For magnesium alloys, Thixomoulding became the dominant process around the world. For aluminium processing, the situation is different as semisolid processing of aluminium is more technically challenging than for magnesium. Today three processes are leading the process implementation, The GISS method, the RheoMetal process and the SEED process. These processes have all strengths and weaknesses and will fit a particular range of applications. The current paper aims at looking at the strengths and weaknesses of the processes to identify product types and niche applications for each process based on current applications and development directions taken for these processes

Configurable process models are frequently used to represent business workflows and other discrete event systems among different branches of large organizations: they unify commonalities shared by all branches and describe their differences, at the same time. The configuration of such models is usually done manually, which is challenging. On the one hand, when the number of configurable nodes in the configurable process model grows, the size of the search space increases exponentially. On the other hand, the person performing the configuration may lack the holistic perspective to make the right choice for all configurable nodes at the same time, since choices influence each other. Nowadays, information systems that support the execution of business processes create event data reflecting how processes are performed. In this article, we propose three strategies (based on exhaustive search, genetic algorithms, and greedy heuristic) that use event data to automatically derive a process model from a configurable process model that better represents the characteristics of the process in a specific branch. These strategies have been implemented in our proposed framework, and tested in both business-like event logs as recorded in a higher educational ERP system, and a real case scenario involving a set of Dutch municipalities.

The development in the field of ceramics has been increasing over the past several decades. Among all of the dental ceramics, zirconia ceramics show very good mechanical properties and a significant improvement in mechanical function. However, it is properly established that each step of the fabrication process of zirconia ceramics must be controlled to achieve the expected mechanical properties. These steps include the block constructing, sintering process, machining and surface processing. Recent advances have focused on zirconia ceramics in forming and sintering processes, mechanical properties, combining with various materials, and on surface processing. All these items provide conceptions about the formability and machinability of the zirconia. Until now, very excellent studies have been done to specify the evolution of microstructures, phase and mechanical properties of zirconia ceramics during the sintering process. However, more studies are required in this field. This paper aims to demonstrate general views and various studies in the field of zirconia ceramics. The properties, applications and tests performed and the recent developments in the field of zirconia bioceramics are discussed.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

In this work, optimal consumption and investment strategies are derived for risk-averse investors under the 4/2 stochastic volatility class of models. We work under an expected utility (EUT) framework and consider a Constant Relative Risk Aversion (CRRA) investor, who might also be ambiguity-averse. The corresponding Hamilton-Jacobi-Bellman (HJB) and HJB-Isaacs (HJBI) equations are solved in closed-form for a subset of the parametric space and under some restrictions on the portfolio setting, for complete markets. Conditions for proper changes of measure and well defined solutions are provided. These are the first analytical solutions for the 4/2 stochastic volatility model and the embedded 3/2 model for the type of excess returns established in .

The effect of fungicides on fermentation is of paramount importance to control the quality and safety of wines. In this work, the quality (oenological parameters, color, phenolic content, antioxidant activity, and fungicide residues) of wines from Monastrell grapes fortified with iprovalicarb, mepanipyrim and tetraconazole fungicides was evaluated. Along of the winemaking process, initial residues of mepanipyrim and tetraconazole were removed in more than a 90 % while dissipation of iprovalicarb was around 73 %. Significant statistical differences were found in presence of iprovalicarb and mepanipyrim residues especially at the highest concentration assayed. For both fungicides, an increase of the volatile acidity (between 4 and 8.6 times), the lactic acid content (between 8.6 and 20.5 times), the percentage of polymeric anthocyanins (between 1.3 and 1.7 times) and also a slight increase of the total phenolic index and the total anthocyanins content determined by spectrophotometry was observed. On the contrary, the total monomeric anthocyanins content decreased about 16.3 and 28.6 % in presence of iprovalicarb and mepanipyrim, respectively. These results could be related with the addition of SO2 to the grape must and a higher development of acetic acid or lactic bacteria in presence of these fungicides. The color of the final wines was also different in comparison with the control, with a higher yellow component, color intensity, tonality and hue angle, because of pH changes in the medium. Tetraconazole fermentations had a more similar trend to the control wine, probably due to the lower concentration of this fungicide in the grape must at the initial time. No effects on the antioxidant activity was observed for anyone of the target fungicides. A multivariate statistical analysis was done to view interrelationships between different variables (color and anthocyanins profile). The obtained model allowed to separate wines according to the fungicide treatment applied.

Habitual entrepreneurs became an important group of entrepreneurs who make a large contribution to the process of wealth creation. Previous studies have indicated that habitual entrepreneurship is a widespread phenomenon. It highlights the need to focus on the habitual entrepreneurs to understand the dynamic aspect of entrepreneurship. The aim of the article is to present the results of preliminary research on the relationships of entrepreneurial behavior of novice entrepreneurs and habitual entrepreneurs, in particular their motivation and impact on the entrepreneurial process. Research were conducted on a sample of 373 small innovative enterprises in the fourth quarter of 2017. The scale of habitual entrepreneurs in the examined sample is 32.44% and is comparable with research carried out in other countries. Survey results reveal that habitual entrepreneurs have greater tendency to create opportunities (introduction new products or services) than novice entrepreneurs. Habitual entrepreneurs also have higher development rate (increase of turnover) and larger share in the international market than novice entrepreneurs. The article also contains indications for further research into the phenomenon of multiple entrepreneurship.

A hybrid smart process and material design system for nanoimprinting is proposed, which combines with a learning system based on experimental and numerical simulation results. Instead of carrying out extensive learning experiments for various condition, the simulation learning results are partially complimented where the results can be theoretically predicted by numerical simulation. In other word, the lacking data in experimental learning are complimented by simulation-based learning results. Therefore, the prediction of nanoimprint results under various conditions without experimental learning could be realized even for unknown materials. In this study, material and process design for a low-temperature nanoimprint process using glycerol-containing polyvinyl alcohol are demonstrated. Experimental results under limited conditions are learned to investigate optimum Glycerol concentrations and process temperatures. On the other hand, simulation-based learning is used to predict the dependence on press pressure and shape parameters. The prediction results for unknown Glycerol concentrations agreed well with the follow-up experiments.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

Handwriting is a complex perceptual-motor task that requires years of training and practice before complete mastering. Its acquisition is crucial since handwriting is the basis, together with reading, for the acquisition of higher-level skills such as spelling, grammar, syntax, and text composition. Despite correct learning and practice of handwriting, some children never master this skill to a sufficient level. These handwriting deficits, referred to as developmental dysgraphia, can seriously impact the acquisition of other skills and thus the academic success of the child if they are not diagnosed and handled early. In this review, we present a non-exhaustive listing of the tools which are the most reported in the literature for the analysis of handwriting and the diagnosis of dysgraphia. Tools focusing on both the final handwriting product and the handwriting process will be considered. We will then discuss the pros and cons of the existing tools, and the perspectives for the development of future tools.

Nowadays, inherently safer designs are considered as key priorities to prevent or mitigate serious incidents with devastating consequences. The need for process safety assessment during early design phases has motivated the development of several contributions related to computer-aided assessment methodologies in order to measure the inherent safety of chemical processes. In this work, the large-scale production of chitosan from shrimp wastes was evaluated from process safety point of view using the numerical descriptive inherent safety technique (NuDIST).To this end, simulation of the chitosan production was performed using Aspen Plus ® to obtain extended mass and energy balances. The assessment of all the chemicals involved within the process was carried out for the following safety parameters: explosivity (EXP), flammability (FL) and toxicity (TOX). The safety assessment of the process included the parameters of temperature (T), pressure (P) and heat of reaction (HR). The maximum chemical safety score was estimated in 171.01 with ethanol as main contributor to the parameter of explosivity and flammability. The score associated with operating data was calculated in 209.30 and heat of reaction reported to be the most affecting parameter. The NuDIST score was estimated in 380.30. This NuDIST value revealed the low hazards associated with the handling of substances such as shrimp wastes, chitosan and water, as well as the non-extreme temperature and pressure conditions. In general, the large-scale production of chitosan from shrimp shells showed to be an inherently safe alternative of waste valorization.

Recently, the amount of waste generated has been rapidly increasing, there have been difficulties disposing of waste in Korea. As a solution to this, treating waste using a cement kiln has suggested, but the environmental and economic effects have not been specifically studied. In this study, the effects of alternative resources, and reducing the social costs(Installation and Operation) associated with waste treatment facilities were analyzed. Through a co-processing method, a reduction of approximately 53kg of CO2 can be realized during the production of one ton of cement, and cost savings of about 3,815 milion USD. Another effect is an extension of the expiration date for landfills by 7.55 years.

In the last four years, the evolution and adoption of blockchain and, more generally, distributed ledger systems have shown the affirmation of many concepts and models with significant differences in system governance and suitable applications. This work aims to update the critical analysis of blockchain technologies carried out by our previous contribution to this journal, extending the focus to distributed ledger components and systems. Starting from the topical concept of decentralization, we introduce concepts and building blocks currently adopted in the available systems centering on their functional aspects and impact on possible applications. We present some conceptual framing tools helpful in the application context, and we will propose the concept of process authenticity, which we will discuss through two use cases: blockchain document dematerialization and e-voting.

The basis of the discrete-impulse energy supply (DIES) concept is the efficient use of supplied energy. The references describe in detail the general principles of DIES, examine the energy and thermodynamic aspects and the main mechanisms of intensification that can be initiated on the basis of this principle. DIES mechanisms conveniently can be divided into hard and soft ones. The former should be used to stimulate hydromechanical processes, and the latter to accelerate the processes of phase heat and mass transfer, or for the purpose of intensive mixing of multicomponent media. The authors have studied the possibility of using DIES to intensify the hydromechanical processes, in particular emulsification of milk fat (homogenization of milk, preparation of spreads), processing of cream cheese masses. Objects of research were whole non-homogenized milk, fat emulsions, cream cheese mass. In order to evaluate the efficiency of milk homogenization the homogenization coefficient change was studied, which was determined by centrifugation method as the most affordable and accurate one. Emulsions were evaluated according to the degree of destabilization, resistance and dispersion of the fat phase. The rheological characteristics of cheese masses were evaluated by the effective viscosity change.