Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

This paper presents a numerical study on the vertical (axial) and lateral (flexure) behavior of CFST (Concrete-Filled Steel Tube) columns with active hoop prestress; this transverse prestressing effect is achieved by bolting together two steel half-tubes. This study refers to new construction only (i.e., no retrofit). 12 prototype CFST column specimens (segments) are analyzed. These specimens differ in the prestressing force (3 levels) and in the gravity loading ratio (4 levels); they are selected to represent typical ground columns of mid-rise buildings. The structural behavior of these column specimens is simulated with a nonlinear model implemented in Abaqus; the concrete and steel behavior are described with a damage-plasticity and a plasticity model, respectively. Finally, the interface concrete-steel interaction is represented by a hard (compression-only) surface-to-surface contact model. The calculations involve three consecutive loading steps: (i) transverse prestress, (ii) axial force, and (iii) lateral loading (shear force and bending moment). The structural behavior of the CFST columns is deeply examined and discussed; the results show that their axial-flexural capacity is adequate. Noticeably, it is concluded that the overall benefits of prestressing the columns are only modest. Preliminary studies on the aforementioned mid-rise buildings equipped with the CFST columns show that their gravity and wind capacities are largely enough; conversely, their seismic capacity is sufficient for moderate seismic ground motions only.