In recent years, wireless power transfer (WPT) has progressed rapidly in both theory and commercialization abroad. However, existing research into WPT coil design for low-power devices is limited. This paper investigates coil structure using printed circuit board (PCB) for magnetic resonant coupling WPT to address this gap. Specifically, the impacts of key geometric parameters on the coil quality factor and coupling coefficient are analysed through models and simulations. Equivalent PCB coils were formed for mutual inductance models, and four basic compensation circuits were analysed. The impacts of changes in coil thickness, line width, turn spacing, and number of turns on the quality factor of PCB coils were analysed with a fixed outer diameter of the coil. In this paper, to mitigate the coil offset while retaining PCB manufacturing simplicity for practical uses, a dual layer PCB coil structure is proposed. The structure optimizated PCB coil could offer remarkable improvements in the WPT system for low power electronic devices.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

Abstract Due to the relatively low efficiency of thermoelectric (TE) generators, they have mostly been used in niche applications where the unique properties of TE generators outweigh their lack of efficiency, or conditions where it is more reasonable to base the optimal design on maximum generated power rather than maximum efficiency. The aim of this work is to investigate how the different fundamental transport properties (Seebeck coefficient, thermal conductivity and electrical resistivity) in materials with equal figure of merit (ZT) impact TE module design and maximum power output. Further, we discuss and review the strategies to enhance material properties and the latest studies on the TE module performance. It is shown, that by increasing the power factor by a factor of 15 and decreasing the thermal conductivity by 13.33 in order to maintain ZT=1, power output is increased by 45%. This effect is stronger in lower module fill factor and thermal resistance of the heat source and heat sink.

In this paper we discuss a problem of generalization of binomial distributed triangle, that is sequence A287326 in OEIS. The main property of A287326 that it returns a perfect cube n as sum of n-th row terms over k; 0 ≤ k ≤ n−1 or 1 ≤ k ≤ n, by means of its symmetry. In this paper we have derived a similar triangles in order to receive powers m = 5; 7 as row items sum and generalized obtained results in order to receive every odd-powered monomial n^2m+1; m ≥ 0 as sum of row terms of corresponding triangle. In other words, in this manuscript are found and discussed the polynomials D_m(n,k) and U_m(n,k), such that, when being summed up over k in some range with respect to m and n returns the monomial n^2m+1.

Switched-mode power supplies (SMPS) often utilize electrolytic capacitors due to their substantial energy density and economical pricing. However, their ability to function at low temperatures is essential for dependable operation in several sectors, including telecommunications, automotive, and aerospace. This study includes an experimental evaluation of how well standard SMPS electrolytic capacitors operate at low temperatures. This paper investigates the suitability of standard electrolytic capacitors used in switched-mode power supplies (SMPS) for low-temperature applications. The experimental evaluation exposed the capacitors to temperatures ranging from - 5 ∘C to - 40 ∘C, assessing capacitance (Cp), impedance (Z), dissipation factor (DF), and equivalent series resistance (ESR) at each temperature. The capacitor’s time-domain electrical signals were analyzed using the Pearson correlation coefficient to extract discriminative features. These features were input into an Artificial Neural Network (ANN) for training and testing. Results indicated a significant impact of low temperatures on capacitor performance. Capacitance decreased with lower temperatures, while ESR and leakage current increased, affecting stability and efficiency. Impedance proved to be a valuable diagnostic tool for identifying potential capacitor failure, showing a 98.44% accuracy drop at - 5 degrees and 88.75% at the peak temperature, indicating proximity to the manufacturer’s specified limit. The study suggests further research and development to improve electrolytic capacitors’ performance in SMPS systems under cold conditions to enhance efficiency and reliability.

In social sciences, a plethora of studies utilize nominal data to establish the relationship between the variables. This, in turn, requires the correct use of correlation technique. The choice of correlation technique depends upon the underlying assumptions and power of the test of significance. The objective of the research is to explore the best measure of association for nominal data in terms of size, power and bias in estimation. Monte Carlo simulations reveal that the Phi and Pearson correlation statistics performs equally well in terms of size, power, and bias for naturally dichotomous variables. When both variables are artificially dichotomized, the Tetrachoric statistic has an edge in terms of bias to Pearson correlation statistic. If one variable is continuous and other is artificially dichotomized, the Biserial correlation measure turns out to be less biased as compared to Pearson statistic although both statistics exhibit similar power and size properties. If one variable is continuous and other is naturally dichotomized, it is hard to choose between the Point Biserial and Pearson correlation measures. Finally, if one variable is naturally dichotomous and other is artificially dichotomized, correlation coefficient V is compared with Pearson, Phi and Tetrachoric correlation techniques in terms of bias in estimate. The results indicate that the Tetrachoric statistic considerably overestimates the correlation value against non-normal distributions. Pearson and Phi correlation slightly underestimate the correlation value. In contrast, the correlation statistic V perform well.

In this paper, we derive and prove, by means of Binomial theorem and Faulhaber's formula, the following identity between $m$-order polynomials in $T$ $$\sum_{k=1}^{\ell}\sum_{j=0}^m A_{m,j}k^j(T-k)^j=\sum_{k=0}^{m}(-1)^{m-k}U_m(\ell,k)\cdot T^k=T^{2m+1}, \ \ell=T\in\mathbb{N}.$$

This study tries to focusing on applying information communication technology for economic importance of Mid Oil Company (MDOC), which is among contemporary oil companies in Iraq. Since ICT forms a significant aspect of achieving organizational economic objectives, most of public and private bodies seek to utilize ICT tool and techniques to improve work efficiencies. The emerging growth in ICT has made it process and service automation possible in managing organizational activities. To determine this effect of ICT on organizations, this study formulated statistical research model at MDOC through using fifteen questionnaires, which were distributed on three axes. The outcome of the questionnaire analysis revealed that there is inadequate comprehensive infrastructure to suitably support ICT within the selected organization management. In addition, it revealed that there are no ideal standards to maintain and sustain internet networks. Based on these revelations, the study presents recommendation for the adoption of ICT with the aim of minimizing cost, enhancing communication and managing infrastructure. Also recommends the need to support IT department within an organization, with essential equipment, in terms of man and machine, for better efficiency to employ the key of ICT Impact in Iraqi governmental oil companies.

Lead-based ternary chalcogenide thin films of the (PbTe)1-x(PbS)x system were obtained by plasma-enhanced chemical vapor deposition technique (PECVD) under conditions of a nonequilibrium low-temperature argon plasma of an RF discharge (40.68 MHz) at a reduced pressure (0.01 Torr). High-purity elements were directly used as starting materials – Pb, S and Te. Plasma-chemical synthesis was carried out on the surface of of c-sapphire and silicon substrate. The physicochemical properties of the films were studied by various analytical methods. The dependence of the Seebeck coefficient, resistivity, and power factor on the structural properties and composition has been studied. The thermoelectric characteristics were found to be dependent on the film composition. Upon the selection of optimal sulfur concentration one can increase the power factor as compared to single phase PbS ot PbTe films.

Although different assessments and evaluations of Dual-Miller cycle performed, specified output power and thermal performance associated with engine determined. Besides, multi objective optimization of thermal efficiency, Ecological Coefficient of performance ( ) and Ecological function ( ) by the mean of NSGA-II technique and thermodynamic analysis performed. The Pareto optimal frontier obtaining the best optimum solution is chosen by fuzzy Bellman-Zadeh, LINMAP, and TOPSIS decision-making techniques. Based on the results, performances of dual-Miller cycles and their optimization are improved.

Water pollution is the main cause of global ecological degradation and seriously affects people's water supply. In order to respond to the water environmental protection policy and provide management departments with a basis for refining water quality, this paper used the environmental Gini coefficient (EGC) method based on four indicators such as water environmental capacity, population, land area, and gross domestic production (GDP) to represent social factors, economic factors, and environmental factors, respectively. After the optimization, for COD, the EGC based on the land area was 0.30, EGC based on population was 0.21, EGC based on environment capacity was 0.02, and the EGC based on GDP was 0.45, and the sum of EGC was 0.962. From this result, we observed that the change in the Gini coefficient of each indicator was not very big. Hence, the most significant change in the Gini coefficient was that of GDP, with a higher rate than other criteria. Then, the COD, AND, and TP discharge allocation model was constructed to obtain the total allocated discharge permit in Lushui Basin. The results found that the total discharge permit allocation of COD, AN, and TP to the Lushui basin were 51483.304 tons/year, 843.119 tons/year, and 340.926 tons/year, respectively. Based on the GIS spatial analysis technology, the distribution of unfair factors that cause pollution inequity was investigated. Finally, the reduction measures were proposed to implement environmental supervision and strengthen water environment management strictly.

Next generation in-to-out-of body biomedical applications have adopted optical wireless communications (OWCs). However, by delving into the published literature, a gap is recognised in modeling the in-to-out-of channel, since most published contributions neglect the particularities of different type of tissues. Towards this direction, in this paper we present a novel pathloss and scattering models for in-to-out-of OWC links. Specifically, we derive extract analytical expressions that accurately describe the absorption of the five main tissues’ constituents, namely fat, water, melanin, oxygenated and de-oxygenated blood. Moreover, we formulate a model for the calculation of the absorption coefficient of any generic biological tissue. Next, by incorporating the impact of scattering in the aforementioned model we formulate the complete pathloss model. The developed theoretical framework is verified by means of comparisons between the estimated pathloss and experimental measurements from independent research works. Finally, we illustrate the accuracy of the theoretical framework in estimating the optical properties of any generic tissue based on its constitution. The extracted channel model is capable of boosting the design of optimized communication protocols for a plethora of biomedical applications.

Usually in quantum optics, the theory of large- and small-scale waveguide beam splitters is the same. In this paper it is shown that the theory of the nanoscale waveguide beamsplitter has a significant difference from a similar device, but of a larger scale. It is shown that the previously known theory of the waveguide beam splitter is a particular case of the theory presented here. The wave function at the output ports of the nanoscale beam splitter is analyzed. The results obtained are sensitive to the size of the beam splitter, the coupling parameter of the two waveguides, and the degree of nonmonochromaticity of the photons entering the first and second ports of the beam splitter. The results are important for quantum technologies using a nanosized beam splitter.

Competition between cotton, winter, and summer crops is the greatest obstacle for plant breeders in Egypt. Breeders are thus seeking early maturing, high-yielding cultivars that are suited for planting following winter crops. This study was conducted during the 2016 and 2018 growing seasons at the Sakha agriculture research station, Egypt's agricultural research facility. This research used breeding material from the F2, F3, and F4 generations that resulted from crossing Giza 94 and Uzbekistan. During the 2016 growing season, the F2 population was cultivated, and the top 5% of the F2 population (75 plants) were chosen based on the selection criteria. In the summer of 2017, the F3 families were cultivated, and 5% of the superior F3 families were chosen to become the F4 fam-ilies, which were planted in the summer of 2018 at the single plant and bulk studies in a randomised full block design with three replications. The average performance of the characteristics boll weight, seed cotton yield, lint percentage, and lint index increased as generations passed from F2 to F4. In the meanwhile, the characteristic value of the first flower to open decreased, showing the accu-mulation of advantageous alleles. For all examined characteristics, the phenotypic coefficient of variance was greater than the genotypic coefficient of variation. In addition, the data demonstrated that heritability in a broad sense was greater in F4 populations than in F3 and F2 populations. With a few exceptions, the phenotypic and genotypic associations for all investigated characteristics were positive and very significant. According to the data, initial opening flowering and boll weight had a substantial impact on seed cotton output per feddan. In general, five superior families No. 9, 13, 18, 19, and 20 were chosen from the F4 population, which were more significant for yield and yield component than the commercial variety, and these genotypes may be promising for the breeding programme to develop new genotypes with superior yield.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The knowledge of the optical properties of biological tissues in a wide spectral range is highly important for the development of noninvasive diagnostic or treatment procedures. The absorption coefficient is one of those properties, from which various information about tissue components can be retrieved. Using transmittance and reflectance spectral measurements acquired from ex vivo rabbit brain cortex samples, allowed to calculate its optical properties in the ultraviolet to the near infrared spectral range. Melanin and lipofuscin, the two pigments that are related to the ageing of tissues and cells were identified in the cortex absorption. By subtracting the absorption of these pigments from the absorption of the brain cortex, it was possible to evaluate the true ratios for the DNA/RNA and hemoglobin bands in the cortex – 12.33 fold (at 260 nm), 12.02 fold (at 411 nm) and 4.47 fold (at 555 nm). Due to the fact that the accumulation of melanin and lipofuscin increases with the ageing of the brain tissues and are related to the degeneration of neurons and their death, further studies should be performed to evaluate the evolution of pigment accumulation in the brain to prevent the development of Alzheimer, Parkinson and stroke pathologies in the brain.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

On 2013 the Villonaco wind farm (16.5 MW), the first wind farm in continental Ecuador near the city of Loja, began operations. The power generated is delivered to the National Interconnected System (SNI), which services the city. This research confronts two sets of real data, the electricity use of the urban area of Loja, and the power generated by the Villonaco Wind Farm. Electricity use follows clearly defined daily and weekly cycles, and wind power has a seasonal behaviour. The study shows that wind power integration cannot be a long-term stable power source regardless power or generation surplus. Another essential finding is that time series can be used as a statistical source to determine the need for short- (seconds) and long- (days, weeks) term energy storage. Strategies to further the energy autonomy of the urban area through the expansion of the wind farm by a factor of 2 are discussed.

This article introduces new method using ANN to control SVC in order to correct the source power factor of low voltage network. Two ANN approaches are investigated to design accurate and fast power factor correction (PFC) controller. First approach uses simple ANN (SANNA). Second approach uses cascaded ANN (CANNA). ANN regression, performance and the calculated error for both approaches are investigated to select between the two approaches. CANNA is selected as a better solution and it used to build the ANN PFFC controller using database, generated by MATLAB-Simulink, for standard three low voltage levels (240V, 220V and 110V). Nine test cases are carried out to validate the performance of proposed ANN PFC controller with a network has variable loads and low power factor (0.6 approximately). In order to extend the use of the controller to other voltage levels not included in the training process of the cascaded ANN, only the SVC is resized. Another nine cases are carried out with the same loads using the same ANN controller, as it is, to test its performance with the extended voltage level range (415V, 230V and 120V). The results show accurate and fast response in all test cases.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Among the impacts of climate change in West Africa, coastal erosion is the most threatening disaster apart from floods and the increase in temperature. The southern coast of the Dakar region, as part of the most threatened coastal zones in West Africa, records the most current coastal damages in Dakar due to its coastline dynamics and low-lying area. This study was conducted in three littoral cells (Mbao, Bargny and Toubab Dialaw) and aims to investigate if there is a relationship between the coastline dynamic, topographic and slope and the contribution of the geomorphology along the southern coast of Dakar. It helps to understand better the role which plays the topography, Slope and geomorphology in coastal dynamics using remote sensing, cartographic tools and statistical methods. The Modified Normalized Different Water index (MNDWI) was employed to delineate the coastlines before computing the dynamic rate of the coastline using the Digital Shoreline Analysis System (DSAS) software. After that, Topography and Slope were determined using Digital Elevation Model (DEM). Then, the correlation between the coastline dynamic, topography and slope was analyzed through the coefficient of correlation and multiple linear regression model. High dynamic rates were noted in the littoral cells, where the topography and slope are low. In Mbao, there is a significant relationship between the coastline dynamic, topography and slope with a coefficient of correlation of about 0.63. In Bargny, the relationship is also significant, with a coefficient of 0.87. The relationship is not significant in Toubab Dialaw, where topography and Slope are high, with a coefficient of 0.15. We conclude that topography, slope and soil properties play an important role in the study area.

This document makes a comprehensive analysis of the inequality of the water market in Chile, measured by the Gini coefficient method. The situation of water rights in Chile is of particular interest because it is a completely privatized system, where rights are traded in the market and therefore water is presented as a commodity. This privatization of water in Chile occurred as part of the process of neoliberalization since the 1981 Water Code. The results of this study indicate that both the concentration and the inequality in the distribution of water rights is very high. It proposes a profound revision of applying a mercantile logic to a scarce basic resource for life such as water and exploring the importance of its role as a national good for public use.

We investigate the tunneling of quasiparticles through a potential barrier of finite height and width, in a system with a band structure consisting of a quadratic band crossing point (QBCP). We compute the results of the transmission coefficient at various incident angles, and also the conductivity and the Fano factor. We discuss the distinguishing signatures of these transport properties in comparison with other semimetals, as well as electrons in normal metals.

Optinalysis, as a method of symmetry detection, is a new algorithm that intrametrically (within elements or variables) or intermetrically (between elements or variables) computes and compares two or more univariate or multi-clustered or multivariate sequences as a mirror-like reflection of each other (optics-like manner), hence the name is driven. Optinalysis is based by the principles of reflection and moment about a symmetrical line which detects symmetry that reflects a similarity measurement. This proposed methodology was validated in comparison with Pearson method of skewness detection, and also with some algorithms for pairewise alignment and comparison of genomic sequences (Needle, Stretcher, Water, Matcher) on EMBL-EBI website. A results comparison shows that optinalysis is more advance, more sensitive, more inferential and simple alternative approach of skewness detection and pairewise sequence comparison.

A field experiment was conducted for determination of crop coefficient (KC) and water stress coefficient (Ks) for wheat crop under different salinity levels, during 2015-16. Complete randomized block design of five treatments were considered, i.e., 0.51 dS/m (fresh water) as a control treatment and other four saline water treatments (4, 6, 8 and 10 dS/m), for S1, S2, S3 and S4 with three replications. The results revealed that the water consumed by plants during the different crop growth stages follows the order of FW>S1>S2>S3>S4 salinity levels. According to the obtained results, the calculated values of crop coefficients significantly differed from those suggested by FAO No.56 for the crops. The Ks values clearly differ from one stage to another because the salt stress causes both osmotic stress, due to a decrease in the soil water potential, and ionic stress which the average values of water stress coefficient (Ks) follows this order; FW(1.0)=S1(1.0)>S2(1.0)>S3(0.93)>S4(0.82). Overall, it was found the differences are attributed primarily to specific cultivar, the changes in local climatic conditions and seasonal differences in crop growth patterns. Thus, further studies are essential to determine the crop coefficient values under different variables, to make the best management practice (BMP) in agriculture.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Power quality problem is a hot area in power systems and drives that has drawn the attention of many researchers. This is because of the threat it poses on the health of electrical systems and the cost incurred on utility bills. The problem arises as a result of the need for reactive power to be supplied alongside active power in power transmission and distribution. Unfortunately, reactive power is consumed by almost all components of the system, leading to a shortage. To solve this problem, there is a need to compensate for the lost reactive power. Several researchers have proposed various approaches to mitigate this problem such as thyristor switched capacitor bank, series compensator, series reactor, series var compensator (SVC), Static Synchronous Compensator (STATCOM), synchronous condenser and others. In order to further draw attention in this area, this work investigates a number of research papers on power compensation techniques and draw up challenges from each work that can be considered for further investigation. To this end, each research paper reviewed is evaluated in terms of problem solved, technique used, and results obtained. It therefore offers ample opportunities for researchers to explore in improving power quality and power system safety.

Risk-based redispatch optimization is proposed as a methodology to support the Transmission System Operator (TSO) with preventive remedial actions obtained by extending the security constrained unit commitment/economic dispatch with constraints resulting from the risk assessed for the power system. Although being heuristic, the methodology is based on comprehensive dynamic security assessment as time-domain simulations are used, allowing to express the degree of all types of instabilities, e.g., caused by contingencies, in monetary terms. Therefore, the risk is assessed as the expected value of the cost incurred by the TSO. Such approach forms a new pathway to including risk in planning procedures already used by TSOs. Results obtained for the IEEE39 dynamic power system, with costs assigned to load shedding and generator tripping due to single transmission lines short-circuits, are shown as a reference case.

This paper deals with the design, simulation and implementation of shunt hybrid compensator to maintain the power quality in 3-phase distribution networks feeding different types balanced and unbalanced nonlinear loads. The configuration of the compensator consists of a selective harmonic elimination passive filter, a series connected conventional 6-pulse IGBT inverter, acting as the active filter terminated with a dc link capacitor. The theory and modelling of the compensator based on current harmonic components at the load end and their decomposition in d-q axis frame of reference are utilized in the reference current generation algorithm. Accordingly, the source current waveform is made to follow the reference current waveform using a high frequency carrier based controller. Further, this inner current control loop is supported by a slower outer voltage control loop for sustaining desirable dc link voltage. Performance of the compensator is evaluated through MATLAB simulation covering different types of loads and reduction of harmonic currents and THD at the supply side along with excellent regulation of dc link voltage are confirmed. The performance of a hybrid compensator designed and fabricated using the above principles is evaluated and corroborated with the simulation results.

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC)~61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbines technology have reduced their flicker emission, mainly thaks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculated. Low flicker emission values at the Point of Common Coupling (PCC) of the WPP were obtained. The flicker estimation at the PCC, based on the measurement from a single WT, was analyzed using different exponents. The results show that a cubic summation performs better than the quadratic one in the estimation of the flicker emission of a WPP with type III WTs.

While microcredits are, by the development practitioners, repeatedly hailed as a useful measure of development policy, this empirical research in Bangladesh arrives at different results: the governing and disciplinary measures are necessary to trigger the best possible repayment success. Based on interviews with the microfinance beneficiaries, loan officers, and microfinance experts in Bangladesh, I chart some of the most frequently used governing and disciplinary techniques including fictitious proximity of loan officers, their fields of visibility and surveillance processes. The “success” of credit delivery is a neoliberal stance that ensures the ceaseless debt repayment process using the intentional and planned conduct, capitalizing social capital and credit honour reputation, surveillance over business enterprises, use of equivocal language and different forms of deception. The development strategy through microfinance in Bangladesh is a development “dispositif” with a changing shift in its declared social missions.

Authors evaluated the relevant literature related to the purging which is the interaction between selection and inbreeding where the population may get rid of its inbreeding load at least partially. The backroad of the relevant theory was given and the available methods were described both based on the conventional quantitative genetic approach (based on genealogy data) and based on the latest genomic methods. The different parameters necessary for signalling purging (highlighting those inbreeding coefficients which are not yet been widely known in animal and veterinary science) were presented together with the relevant results of the literature. The available statistical methods together with the softwares and R packages to calculate various inbreeding coefficients and to determine inbreeding depression and purging were provided. The main results of the different approaches obtained in laboratory ZOO and domesticated populations (lethal equivalents, ancestral inbreeding, Inbreeding-Purging Model, genomic approaches) were summarized and presented. Application possibilities and future prospective of purging was also discussed.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

The Power Theory of Exchange and Money (PTEM) refines the economic neoclassical two-equation model of exchange. PTEM replaces the statistical average condition of exchange, which represents the equality of supply and demand for all transactions in the market, with a more specific equation of the equality of the generalized power of the parties in relation to their objects of exchange. The purpose of the article is to show the application of PTEM for the study of various social phenomena. Along with a brief summary of the main statements of this theory, its integration into the existing corpus of theories and ideas in economics and sociology is considered. The conclusions of power theory are then applied to consider the following topics: the objective motivation of exchange by the desire to increase power, the power nature of market equilibrium, the power nature of money, the accumulation of power through profit, the creation of money as a power act, the role of the state in the creation of money, the measure of power as a possible tool for social and political research.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

This paper investigates the influence of different vegetation on the permeability of the shallow soil layers of slopes under rainfall infiltration. Firstly, four large slopes are filled in the outdoor natural environment, and the overburdens of the four slopes are Magnolia multiflora, Cynodon dactylon, Magnolia multiflora mixed with Cynodon dactylon, and no vegetation. Secondly, the four slopes are cultivated in the outdoor natural environment for one year. After the vegetation overburdens are matured, the field artificial rainfall test is carried out through the self-developed artificial rainfall device to monitor the water migration law inside the four slopes in real time. Finally, the unsaturated permeability coefficients of the shallow soil layers of slopes are calculated. The results show that the infiltration rate of rainwater in each overburden slope from fast to slow is Magnolia multiflora overburden slope, no vegetation slope, Cynodon dactylon overburden slope, Magnolia multiflora mixed with Cynodon dactylon overburden slope. In the early stage of rainfall, Magnolia multiflora increases the permeability coefficient of the shallow soil layer of the slope, thus weakening the anti-seepage ability of the slope, but the influence of Magnolia multiflora is not obvious in the later stage. Cynodon dactylon and Magnolia multiflora mixed with Cynodon dactylon can significantly reduce the permeability coefficient of the shallow soil layers of the slopes, thereby increasing the anti-seepage ability of the slopes, and the mixed planting of Magnolia multiflora and Cynodon dactylon can minimize the permeability coefficient of the shallow soil of the slope, resulting in the best anti-seepage effect.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

The key concepts in symmetry detection and similarity, identity measures are automorphism and isomorphism respectively. Therefore, methods for symmetry detection and similarity, identity measures should be functionally bijective, inverse, and invariance under a set of mathematical operations. Nevertheless, few or no existing method is functional for these properties. In this paper, a new methodological paradigm, called optinalysis, is presented for symmetry detections, similarity, and identity measures between isoreflective or autoreflective pair of mathematical structures. The paradigm of optinalysis is the re-mapping of isoreflective or autoreflective pairs with an optical scale. Optinalysis is characterized as invariant under a set of transformations and its isoreflective polymorphism behaves on polynomial and non-polynomial models.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Human resources are the major input of health systems therefore the equitable distribution of human resources in health care remain critical in making progress towards the goal of universal health coverage and thus to sustainable development. The purpose of this study is to evaluate the health care human resources distribution across regions of Poland between 2010 and 2017 and estimate the level of equity. This research by applying to Polish conditions will allow to fill in the gap in existing literature. Data was derived from the Knowledge Database Health and Health Care of Statistic Poland and Polish Statistical Yearbook. In purpose to examine the distribution of health resources against population size and geographic size in Poland, the Gini coefficient calculated based on the Lorenz Curve was engaged. This study has several major findings. The amount of most types of human resources – as apart from internist, obstetrics and gynecology, occupational medicine - when expressed as number of them per 10,000 population or 1 square km increased in 2017 compared to 2010. Moreover, for most types of health care human resources the level of access slightly changed during analysied period as Gini coefficients decreased. However, the geographical distribution of all types of human resources is less equitable then in case of population distribution. The most troublesome is relatively lower equity in case of oncologist, family medicine and occupational medicine and cardiologist in both population and geographical distribution. Thus this research provides some implications for policy and practice. As the main reason to establish National Health Fund (which meant the centralization of the system) in Poland was to to eliminate regional differences in access to health care, thus this research confirms that still some more corrective actions, in this field, should be undertaken.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

In estimating the maximum and minimum index void ratios for mixtures of sand and silt, the values of several empirical constants must be determined based on the type of sand and silt involved. These empirical constants are the filling coefficient, a, and embedment coefficient, b, both of which can be determined either through lab testing or correlations. These constants are then used in equations to predict the maximum and minimum index void ratios of the sand-silt mixtures. The study reported here developed simple correlations for estimating the filling and embedment coefficients using readily obtained laboratory data. These models were found to be excellent in developing filling and embedment coefficients that accurately (R2 values typically of 0.94 or greater.) predicted values of the index void ratios for sand and silt mixtures.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

One of the challenges posed by renewable energies is the stabilization of parameters related to the quality of electrical energy. This study demonstrates the existence of a relationship between input blocks of hydropower and the variation of the fundamental frequency of the electricity grid. By mapping production data provided by Spanish Electric Network with frequency measured in the laboratory, it is shown that gradients of hydropower are correlated with frequency fluctuations for certain characteristic times. Considering hourly instances of energy input, the study compares two methods for calculating hydropower gradients (linear regression and pseudo-linear regression); and two methods for calculating local frequency extremes (the "specular inertia" method and analysis by comparison with the moving average), in order to corroborate the results.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

This study aimed to evaluate potential posttreatment changes in ADC values within the tissue surrounding the enhancing lesion, particularly in areas not exhibiting MRI characteristics of in-volvement. Additionally, the objective was to investigate the correlation between ADC values, treatment response, and survival outcomes in individuals diagnosed with gliomas. This retrospective study included a total of 49 patients that underwent either stereotactic biopsy or maximal surgical resection. Histologically confirmed as Grade III or IV gliomas, all cases adhered to the 2016 and 2021 WHO classifications, with subsequent radio-chemotherapy administered post-surgery. Patients were divided into two groups: short and long survival group. Baseline and follow-up MRI scans were obtained on a 1.5T MRI scanner. Two ROI circles were positioned near the enhancing area, one ROI in the NAWM ipsilateral to the neoplasm and another symmetrically in the contralateral hemisphere on ADC maps. At follow-up there was a significant difference in both ipsilateral and contralateral NAWM be-tween the two groups, -0.0857 (p=0.004) and -0.0607 (p=0.037), respectively. There was a weak negative correlation between survival and ADC values in ipsilateral and contralateral NAWM at the baseline with the correlation coefficient -0.328 (p=0.02) and -0.302 (p=0.04), respectively. The correlation was stronger at the follow-up. The findings indicate that ADC values in normal appearing white matter (NAWM) may function as a prognostic biomarker in patients with diffuse gliomas.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

Trade of agricultural products has gained importance with the development of global trade. Cherries has a crucial place in Turkish agricultural exports. Fresh cherries are in the scope of this study. The aim of this study is to examine Turkey’s position and competitiveness in cherry trade. Trade Intensity Analysis Method which represents the course of trade flow among countries is used in the study. The study indicates that European countries which are Turkey’s tradition trade partner has a biggest trade share with Turkey and that share did not much change in years. By the way, Asia market especially China, became a game changer in cherry trade and Turkey should prepare itself for this situation.

This algorithm is designed to perform Discrete Fourier Transforms (DFT) to convert temporal data into spectral data. This algorithm obtains the Fourier Transforms by studying the Coefficient of Determination of a series of artificial sinusoidal functions with the temporal data, and normalizing the variance data into a high-resolution spectral representation of the time-domain data with a finite sampling rate. What is especially beneficial about this DFT algorithm is that it can produce spectral data at any user-defined resolution.

Background: Early identification and prevention of hypoxic ischemic encephalopathy (HIE) may reduce neonatal mortality and morbidity. Objective: We aimed to correlate between urinary Activin-A and MRI (conventional and Diffusion-weighted) and the severity of HIE in full-term neonates. Methods: Forty-five full-term neonates with HIE admitted to NICU and 15 normal neonates were enrolled into the study. The concentration of urinary Activin-A was determined using enzyme immunoassay kits and MRI were done. Correlations between urinary Activin-A and MRI with the degree of HIE were done. Results: Urinary Activin-A levels were significantly higher in neonates with HIE than controls (P<0.001). It was positively correlated with the clinical grading of HIE and a cutoff value of 0.08µg/l on day-1 after birth had a sensitivity of 98.6% and specificity of 97.1% for prediction of HIE. DW-MRI detected HIE with a high sensitivity (85%) compared to the low sensitivity of conventional MRI (35%). An ADC value of ≤ 0.8 was the best sensitivity-specificity cutoff point for detecting severe ischemic injury. DW-MRI imaging was positively correlated with Urinary Activin-A and both of them were positively correlated with the clinical grades of HIE (P < 0.001). Conclusions: DW-MRI imaging is correlated well with urinary Activin-A in full-term neonates with HIE and both of them are correlated with the degree of HIE. Early determination of urinary Activin-A combined with DW-MRI imaging can early detect HIE and its severity in full-term neonates with HIE.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

Different types of resonators are used to create acoustic metameterials and metasurfaces. Recent studies focused on the use of multiple resonators of dipole, quadrupole, octupole and even hexadecapole types. This paper considers the theory of an acoustic metasurface, which is a flat surface with a periodic arrangement of multiple resonators. The sound field reflected by the metasurface is determined. If the distance between the resonators is less than a half the wavelength of the incident plane wave, the far field can be described by a reflection coefficient that depends on the angle of incidence. This allows to characterize the acoustic properties of the metasurface by a homogenized boundary condition, which is a high order tangential impedance boundary condition. The tangential impedance depending on the multiple order of the resonators is introduced. In addition, we analyze sound absorption properties of these metasurfaces, which are a critical factor in determining their performance. The paper presents a theoretical model that accounts for the multiple orders of resonators and their impact on sound absorption. The maximum absorption coefficient for a diffuse sound field, as well as the optimal value for the homogenized impedance, are calculated for arbitrary multipole orders.

Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

The interaction between the grid network and the offshore wind power plant (WPP) network can lead to the amplification of certain harmonics and potentially resonant conditions. Offshore WPP should limit the increment of harmonic voltage distortion at the point of connection to the grid network as well as within their internal network. The harmonic distortion should be limited within the planning level limits using harmonic compensation, which is usually achieved by using static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of resistance at the harmonic frequencies of concern is analysed. Such a compensation is effective for the local bus, though the performance is not guaranteed at the remote bus. This paper investigates the challenges associated with remote harmonic compensation in the offshore WPP, which is connected to the onshore grid through long high-voltage cables and transformers. First, the harmonic distortion and the compensating effects of the filter are theoretically assessed. Afterwards, they are demonstrated using harmonic propagation studies and time domain simulations in PSCAD.

A supply chain management (SCM) system is a strategic cooperative that organically integrates all supply chains to improve the performance of a company. The greatest critical success factor of SCM is partnership. Without cooperation between companies, SCM performance is limited. Does this imply, therefore, that companies within the supply chain can achieve mutual transactions equally? If the power between companies is unequal, how does this affect their partnership? The focus of this study is to assess whether power types enhance SCM performance through partnerships. We categorize power types as mediated and non-mediated. Mediated power is categorized based on coercion, reward, and legitimate, while non-mediated power is categorized based on information, expert, and reference. Therefore, this study examines how power types form a causal partnership relationship within the supply chain, and performs an empirical investigation on how the partnerships influence SCM performance.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

In the interaction of the rolling stock and the upper structure of the railway track, intense dynamic loads occur. They have a destructive effect both on the parts of the rolling stock and on the elements of the superstructure of the track. In order to develop a durable, rational and reliably functioning design of cars and locomotives with good dynamic properties and good indicators of the impact of rolling stock on the railway track, along with theoretical computational studies, experimental studies are also required, which are usually the final stage in the design and implementation of rolling stock or modernization of existing ones. Locomotives and wagons in order to improve their strength and dynamic performance. The article presents the results of field tests to determine the dynamic performance of the type CKD6e diesel locomotive. The description of the preparation of the CKD6e shunting locomotive for testing is given. An analysis of the dynamic performance of a diesel locomotive during the passage of turnouts, on a straight section of the track and in a curve with a radius of 400 m, was carried out. The studies performed showed that the minimum value of the stability factor against wheel derailment on a straight section of the track is significantly higher than the standard value. The experimentally obtained ratio of frame forces to the static load from the wheelset on the rails, the coefficients of vertical dynamics of the first and second stages of suspension and the coefficient of stability against derailment of the wheel from the rail, registered on the track section in a curve with a radius of 400 m) meet the current requirements. A calculation scheme and equations of vertical oscillations are proposed, an analysis is carried out according to the graphs of movements of bogies and a locomotive body when moving along irregularities of different lengths at different speeds.

In the Cerrado-Amazonian ecotone in the State of Mato Grosso, intensely altered by anthropic action, the knowledge and processes of energy conversion and energy balance are still incipient, making the monitoring and modeling of diffuse radiation essential for several applications. The objective of this study was to evaluate the seasonality of the diurnal evolution and estimate the hourly diffuse radiation (Hdh) incident radiation in the horizontal plane, between June 2011 and October de 2016. The instantaneous measurements (5 minutes) of diffuse radiation underwent geometric, astronomical, and anisotropic corrections, with subsequent hourly integrations. The seasonality of diffuse radiation and its radiometric fractions was evaluated. The estimates were made considering total and seasonal data groupings (water stations in the region) and in different cloudiness classes (atmospheric transmissivity index - KTh). The diurnal behavior of diffuse radiation (Hdh) was similar to that of global radiation and at the top of the atmosphere, with maximum values at solar noon. The correlations between Kdh and KTh showed third-order polynomial behavior, with maximum observed values of Kdh ranging from 0.8 to 0.9, for KTh less than 0.2. Estimation equations based on radiometric fractions underestimated the values of diffuse radiation, with a better performance presented by models adjusted in annual data groupings. Among the parameterized models for estimating diffuse radiation obtained in the literature, those calibrated regionally in this study, together with those developed for tropical regions, presented better statistical performances.

We evaluate various binomial sums involving the powers of Fibonacci and Lucas numbers.

We consider the inverse function $z=g(w)$ of a (normalized) starlike function $w=f(z)$ of order $\alpha$ on the unit disk of the complex plane with $0<\alpha<1.$ Krzy{\. z}, Libera and Z\l otkiewicz obtained sharp estimates of the second and the third coefficients of $g(w)$ in their 1979 paper. Prokhorov and Szynal gave sharp estimates of the fourth coefficient of $g(w)$ as a consequence of the solution to an extremal problem in 1981. We give a straightforward proof of the estimate of the fourth coefficient of $g(w)$ together with explicit forms of the extremal functions.

Background: Malaria is one of the most common diseased conditions across most developing countries caused by one of four species of Plasmodium. P. falciparum and P.vivax are the main agents responsible for malaria in Nigeria. Malarial infection has been shown to be associated with abnormalities in fluids, electrolytes and acid base balances. Electrolyte imbalance and mineral disturbances are majorly identified clinical symptoms in various infectious diseases including malaria. Electrolyte imbalance in malarial infection is capable of enhancing disease severity. The aim of this study was to investigate the effects of malarial infection on electrolytes parameters. Methods: Finger prick blood samples, Thick and Thin Giemsa-stained blood smears, were collected from 100 malaria-suspected individuals representing all age groups. The Giemsa-stained blood smears were examined microscopically. Demographic information was obtained using structured questionnaires. The electrolytes levels (Na, K, Cl^- and HCO_3-) in malarial patients were analyzed using standard procedures, Pearson's Correlation Coefficient correlation technique was used to investigate the relationship, and the strength of association between the variables. Results: The mean bound of patients’ sodium level was observed to fall within the specified normal limits of 125mmol/L – 145mmol/L; except for positive malaria patients belonging to the MP-(++) which will fall below the 125mmol/L (i.e. 126.25mmol/L – 1.77mmol/L = 124.48mmol/L). The spread of the sodium data taken from the patients were observed to fall within the normal limits leaving only the boxplot’s lower whisker out, that is, observations falling within the first quartile, except for MP-(++) patients with observations in the first to second quartile spreading outside the normal lower limit, in contrast for the negative tested patients, the box and its whiskers were almost engulfed within the normal limits. Conclusion: In our study we found that Plasmodium falciparum altered more in electrolytes parameters than Plasmodium vivax. The biochemical markers can be used as biomarkers to confirmation of malaria. This study discovered a significant linear relationship based on the Pearson product-moment correlation between creatinine and urea, potassium and chloride, potassium and creatinine, potassium and urea. The mean sodium and chloride level of positive malaria [MP-(++)] patients were observed to fall outside the normal limit.

The ongoing outbreak of the novel coronavirus pneumonia (also known as COVID-19) has triggered a series of stringent control measures in China, such as city closure, traffic restrictions, contact tracing and household quarantine. These containment efforts often lead to changes in the contact pattern among individuals of the population. Many existing compartmental epidemic models fail to account for the effects of contact structure. In this paper, we devised a pairwise epidemic model to analyze the COVID-19 outbreak in China based on confirmed cases reported during the period February 3rd--17th, 2020. By explicitly incorporating the effects of family clusters and contact tracing followed by household quarantine and isolation, our model provides a good fit to the trajectory of COVID-19 infections and is useful to predict the epidemic trend. We obtained the average of the reproduction number $R=1.494$ ($95\%$ CI: $1.483-1.507$) for Hubei province and $R=1.178$ ($95\%$ CI: $1.145-1.158$) for China (except Hubei), suggesting that some existing studies may have overestimated the reproduction number by neglecting the dynamical correlations and clustering effects. We forecasted that the COVID-19 epidemic would peak on February 13th ($95\%$ CI: February $9-17$th) in Hubei and 6 days eariler in the regions outside Hubei. Moreover the epidemic was expected to last until the middle of March in China (except Hubei) and late April in Hubei. The sensitivity analysis shows that ongoing exposure for the susceptible and population clustering play an important role in the disease propagation. With the enforcement of household quarantine measures, the reproduction number $R$ effectively reduces and epidemic quantities decrease accordingly. Furthermore, we gave an answer to the public concern on how long the stringent containment strategies should maintain. Through numerical analysis, we suggested that the time for the resumption of work and production in China (except Hubei) and Hubei would be the middle of March and the end of April, 2020, respectively. These constructive suggestions may bring some immeasurable social-economic benefits in the long run.

Longitudinal dispersion coefficient (LDC) plays an essential role in modeling the transport of pollution and sediment in the natural rivers. As a result of transportation processes, the concentration of pollution changes along the river. Different studies have been conducted to provide simple equations for estimating LDC. In this study, Support Vector Regression (SVR), Gaussian Process Regression (GPR), M5P and Random Forest (RF) examined to predict the LDC in the natural streams. The hydraulic and geometric features of different rivers gathered for developing the mentioned models for LDC estimation and various statistical criteria were utilized to scrutinize of the models. Furthermore, the Taylor chart was used to evaluate the models and achieved results showed that among machine learning models, M5P displayed the superior performance with CC of 0.823, SI of 0.812, NS of 0.577 and WI of 0.879. As well, S-D model with CC of 0.795 SI of 0.827, NS of 0.558 and WI of 0.890 had more precise results than other empirical models. The results indicates that the developed M5P model with simple formulations was superior to other machine learning models and empirical models and therefore, it can be used as a proper tool for estimating LDC in natural rivers.

Aim: The aim of the paper is to assess the usefulness of sectoral means in financial analyses of enterprises. Research methods: The article uses an inductive-deductive approach to assess the suitability of sectoral means used in analyses of financial standings of enterprises. The method of analysis and logical construction was used for literature review. The methods of descriptive statistics such as, arithmetic means, standard deviation and coefficient of variation were used in order to analyze the data and draw conclusions based on the results. Contribution: The assessment of the usefulness of sectoral means in the context of their variability seems to be a crucial aspect for the analysis of a company’s financial situation. When assessing the financial standing of an enterprise, it is necessary to use a comparative analysis method, based on, inter alia, a comparison in space. This type of comparison requires the use of sectoral means, whose assessment is extremely important to drawing reliable and correct conclusions of the financial situation of a company.

Colostrum is a natural product, issued by both mammals and humans in first week of lactation. Among different species, donkey colostrum is considered as having, besides a valuable composition in nutrients and immune factors, an outstanding similitude with human colostrum. In this context, and taking into account the scarcity of available data concerning the interaction between climate factors and colostrum quality, a trial was conducted aiming to identify the possible influence of environmental factors on donkey colostrum nutritional traits. A stock of 16 jennies from 2 farms located in the County of Cluj, during a 7 days postpartum period was analyzed. During experimental period the daily temperature, humidity, and wind velocity data were collected. Strong positive correlations may be reported between fat and lactose, and fat and protein respectively, while moderate to strong correlation is emphasized between lactose and protein content of donkey colostrum. Testing the influence of environmental temperature, relative humidity, and wind velocity influence upon nutritional content of donkey colostrum, results the neglectable influence of the wind velocity, the negative influence of the heat stress upon all studied colostrum components, and complex influence of relative humidity, which has positive influence on fat and lactose increase when it increases, while its increase has negative influence on protein content of donkey colostrum.

In this paper, the nanoscale dissipative mechanisms of a Cu pad in a Ball Grid Array (BGA) packaging structure during isothermal ageing and uniaxial tension were investigated by the molecular dynamics (MD) method and experiments. From the result of the isothermal ageing test, a nonuniform consumption of Cu and large amount of Kirkendall voids were observed at the interface of Cu and Cu₃Sn. To study the effect of pressure and orientation on this phenomenon, MD simulations were conducted on four types of Cu-Cu₃Sn interface structures with different orientations of Cu. By comparing the diffusion coefficients of atoms in those cases, it was found that the tensile stress would inhibit the diffusion of atoms, whereas compressive stress would accelerate it, and this would be more significant under a larger magnitude of stress and temperature. Note that, in the model with the (101) surface Cu at the interface, both Cu and Cu₃Sn have a higher diffusion coefficient compared with the model with (001) surface Cu. Thus, the orientation of Cu will also contribute to the uniform consumption of the pad. Uniaxial tension simulation combined with DXA and CSP analyses on those models also shows the model with (001) surface Cu has a greater mechanical reliability in our simulations and related experiments.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

A decade ago, non-radiative wireless power transmission reemerged a promising alternative to deliver electrical power to devices where a physical wiring proved to be unfeasible. However, conventional coupling-based approaches are neither scalable nor efficient when multiple devices are involved, as they are restricted by factors like coupling and external environments. Zenneck waves are excited at interfaces, like surface plasmons and have the potential to deliver electrical power to devices placed on a conducting surface. Here, we demonstrate, efficient and long range delivery of electrical power by exciting non-radiative waves over metal surfaces to multiple loads.Our modeling and simulation using Maxwells equation with proper boundary conditions shows Zenneck type behavior for the excited waves and are in excellent agreement with experimental results. In conclusion, we physically realize a radically different power transfer system, based on a wave, whose existence has been fiercely debated for over a century.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

Complex modeling has received significant attention in recent years and is increasingly used to explain the statistical phenomenon with increasing and decreasing fluctuations such as the similarity or difference of spike protein charge patterns of coronaviruses. Different from the existing covariance or correlation coefficient methods in traditional integer dimension construction, this study proposes a simplified novel fractional dimension derivation with the exact Excel tool algorithm. It involves the fractional center moment extension to covariance, which ends up a complex covariance coefficient that is better than the Pearson correlation coefficient, in the sense that the nonlinearity relationship can be further depicted. The spike protein sequences of coronaviruses were obtained from the GenBank and GISAID database, including the coronaviruses from pangolin, bat, canine, swine (three variants), feline, tiger, SARS-CoV-1, MERS, and SARS-CoV-2 (including the strains of Wuhan, Beijing, New York, German, and UK variant B.1.1.7) were used as the representative examples in this study. By examining the values above and below the average/mean based on the positive and negative charge patterns of the amino acid residues of the spike proteins from coronaviruses, the proposed algorithm provides deep insights into the nonlinear evolving trends of spike proteins for understanding the viral evolution and identifying the protein characteristics associated with viral fatality. The calculation results demonstrate that the complex covariance coefficient analyzed by this algorithm is capable of distinguishing the subtle nonlinear differences in the spike protein charge patterns with reference to Wuhan strain SARS-CoV-2 for which the Pearson correlation coefficient may overlook. Our analysis reveals the unique convergent (positive correlative) to divergent (negative correlative) domain center positions of each virus. The convergent or conserved region may be critical to the viral stability or viability; while the divergent region is highly variable between coronaviruses suggesting high frequency of mutations in this region. The analyses show that the conserved center region of SARS-CoV-1 spike protein is located at amino acid residues 900, but shifted to the amino acid residues 700 in MERS spike protein, and then to amino acid residues 600 in SARS-COV-2 spike protein, indicating the evolvement of the coronaviruses. Interestingly, the conserved center region of the spike protein in SARS-COV-2 variant B.1.1.7 shifted back to amino acid residues 700, suggesting this variant is more virulent than the original SARS-COV-2 strain. Another important characteristic our study reveals is that the distance between the divergent mean and the maximal divergent point in each of the viruses (MERS>SARS-CoV-1>SARS-CoV-2) is proportional to viral fatality rate. This algorithm may help to understand and analyze the evolving trends and critical characteristics of SARS-COV-2 variants, other coronaviral proteins and viruses.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

(1) Background: Conventional strength training and core exercises are commonly prescribed to improve cycling performance. Although previous studies have explored the utility of strength training in various cycling populations, this intervention has never been compared to core exercises; (2) Methods: 36 trained road cyclists were divided in 3 groups of 12 participants that performed either no strength training, conventional strength training or core exercises, in all cases together with their regular cycling training during a 12-week period. Peak power outputs across different durations (5 seconds, 60 seconds, 5 minutes, and 20 minutes) were recorded before and after the intervention; (3) Results: Conventional strength training is superior to core training and no strength training for all measured durations. At the same time, core training results in improved 5 second power output when compared to no strength training, while all the other measures are comparable among groups; (4) Conclusions: Conventional strength training is superior to core exercises and no strength training in trained road cyclists, and accordingly, it is recommended that this population incorporates strength training during their regular weekly workouts.

The study of the optical properties of biological tissues for a wide spectral range is necessary for the development and planning of noninvasive optical methods to be used in clinical practice. In this study, we propose a new method to calculate almost all optical properties of tissues as a function of wavelength directly from spectral measurements. Using this method and with the exception of the reduced scattering coefficient, which was obtained by traditional simulation methods, all the other optical properties were calculated in a simple and fast manner for human and pathological colorectal tissues. The obtained results are in good agreement with previous published data, both in magnitude and in wavelength dependence. Since this method is based on spectral measurements and not on discrete-wavelength experimental data, the calculated optical properties contain spectral signatures that correspond to major tissue chromophores such as DNA and hemoglobin. Analysis of the absorption bands of hemoglobin in the wavelength dependence of the absorption spectra of normal and pathological colorectal mucosa allowed to identify differentiated accumulation of a pigment in these tissues. The increased content of this pigment in the pathological mucosa may be used for the future development of noninvasive diagnostic methods for colorectal cancer detection.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.

To quantitatively estimate the risk of power system operation under extreme rainfall, a multi-scenario stochastic risk assessment method is proposed. First, a scenario generation scheme considering waterlogged faults of power facilities is constructed based on the storm water management model (SWMM) and the extreme learning machine method. These scenarios will be merged to several typical scenario sets for further processing. The outage of power facilities will induce power flow transfer which may consequently lead to transmission lines’ thermal limit violation. Semi-invariant and Gram-Charlier level expansion methods are adopted to analytically depict the probability density function and cumulative probability function of each line’s power flow. The optimal solution is performed by a particle swarm algorithm to obtain proper load curtailment at each bus, and consequently the violation probability of line thermal violations can be controlled within an allowable range. The volume of load curtailment as well as their importance are considered to quantitatively access the risk of power supply security under extreme precipitation scenarios. The effectiveness of the proposed method is verified in case studies based on the IEEE 24-bus system.

The local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) is essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using the linear decision tree regression to support voltage stability and provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference ones suggested by grid codes.

Harmonic resonances are part of the Power Quality (PQ) problems of electrified railways and have serious consequences for the continuity of service and integrity of components in terms of overvoltage stress. The interaction between Traction Power Stations (TPSs) and trains that causes line resonances is briefly reviewed showing the dependence on infrastructure conditions. The objective is real-time monitoring of resonance conditions seen first of all from the onboard panto-graph interface, but it is equally applicable at TPS terminals. Voltage and current spectra, and de-rived impedance and power spectra, are analyzed proposing compact and efficient methods based on Short-Time Fourier Transform, suitable for real-time implementation with the hardware avail-able for energy metering and harmonic interference monitoring. The methods are tested by sweeping long recordings taken at some European railways, covering cases of longer and shorter supply sections, with a range of resonance frequencies of about one decade. They give insight into the spectral behavior of resonances, their dependency on position and change over time, and criteria to recognize genuine infrastructure resonances from rolling stock emissions.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.