The influences of doped hole transporting layer (HTL) on the performances of perovskite solar cells were studied. The influences of electrostatic and surface roughness effect by solvent additive doping were compared. The electrostatic effect of solvent additive doping was compared by addition of 1,8-diiodooctane and 1,8-dichlorooctane to the HTL layer. The surface roughness effect of solvent additive doping was examined using atomic force microscopy. The perovskite crystallinity by doping HTL was studied by X-ray diffraction. The conductivity of HTL was measured using four probe methods and was higher for doped devices. Enhanced conductivity of PEDOT:PSS film was also proved using fluorescence emission quenching. Long-term stability of the device was enhanced by doping HTL. The device with solvent additive exhibited much enhanced stability, retained over 80% of the initial PCE for 400 hours, while PCE of the device without solvent additive decreased to less than 80% after 200 hours. A very weak power microwave treatment was used for post-annealing of the fully fabricated devices. Post-annealing enhanced the lifetime of the device. Comparing different size of cells, the device lifetime was decreased as the cell area increased and as the size of the cell increased, the extent of lifetime enhancement by doping was increased.

Here we report the effect of substrate, sonication process, and post-annealing on the structural, morphological, and optical properties of ZnO thin films grown in the presence of isopropyl alcohol (IPA) at temperature 30 – 65 ℃ by successive ionic layer adsorption and reaction (SILAR) method on both soda lime glass (SLG) and Cu foil. The X-ray diffraction (XRD) patterns confirmed the preferential growth thin films along (002) and (101) plane of wurtzite ZnO structure while grown on SLG and Cu foil substrate respectively. Both XRD and Raman spectra confirmed the ZnO and Cu-oxide phases of the deposited films. Scanning electron microscope (SEM) image of the deposited films shows compact and uniformly distributed grains for samples grown without sonication while using IPA at temperature 50 and 65 ℃. The post-annealing treatment improves the crystallinity of the films, further evident by XRD and transmission and reflection results. The estimated optical bandgaps are in the range of 3.37-3.48 eV for as-grown samples. Results revealed that high-quality ZnO thin films could be grown without sonication using IPA dispersant at 50 ℃, which is much lower than the reported results using the SILAR method. This study suggests that in the presence of IPA, the SLG substrate results in better c-axis oriented ZnO thin films than that of DI water, ethylene glycol, propylene glycol at the optimum temperature of 50 ℃. Air-annealing of the samples grown on Cu foils induced the formation of Cu_xO/ZnO junctions which is evident from the characteristic I-V curve including the structural and optical data.

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

The work proposes a new approach for evolutionary global optimization which, in simple terms, may be described as a fusion of quantum and simulated annealing. This becomes possible by using basic concepts from Homotopy Theory, conjugated to the already existing Fuzzy Adaptive Simulated Annealing paradigm and other components. In this fashion, it occurs a temporal and nonlinear superposition of the two types of annealing, provoking interesting effects in runtime, including the so-called quantum tunneling, when there is a sudden transition between attraction basins of different minima without "climbing" potential barriers. In addition, the proposal includes a generalization of the "deformation" of Hamiltonians used in quantum annealing by suggesting the use of general homotopies between the surface corresponding to the cost function under processing and another specific landscape, being this possible because of the ability of Fuzzy ASA of handling time-varying objective functions. The proposed paradigm shows that it is possible and beneficial to superpose the two types of annealing, displaying amazing numerical results and suggesting a kind of interlacing or synergic behavior - perhaps we could call it an "annealing entanglement". Finally, given the fast advances in commercial quantum annealing processors, it seems sensible to expect that an implementation of the proposed approach using such devices may occur very soon. In order to demonstrate the efficacy of the proposed algorithm, some significant and detailed examples are included in the text, so as to illustrate and clarify the presented ideas.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

In this study, we address the formidable challenge of solving large-scale Max-Cut problems (MCP). We introduce a rapid computational procedure utilizing a hybrid 1-flip/r-flip local search heuristic. This innovative strategy significantly reduces the computational time required for MCP problems while consistently generating solutions of exceptional quality. The paper presents substantial computational insights, showcasing the effectiveness of our approach on very-large-scale Max-Cut instances with varying densities. Our proposed heuristic is rigorously evaluated by comparing its performance against a quantum annealing solver, leveraging a multi-start Tabu Search framework. The results underscore the potency of this unique combination as an efficient and effective solution for large-scale QUBO problems. Notably, our hybrid heuristic consistently delivers high-quality solutions within the stringent CPU time limits of 600 seconds, demonstrating its efficacy across Max-Cut instances ranging from 10,000 to 40,000 variables. This research contributes to advancing the state-of-the-art in large-scale QUBO problem-solving, offering a powerful and time-efficient approach with broad applicability.

In this contribution we present work on rapid thermal annealing of as-electrodeposited thin films of Cu2ZnSnS4. The treatment was carried out in cold wall tubular reactor in dynamic conditions with variations of temperature, speed and time of the specific elements of the process. The effect of annealing was investigated by X-ray diffractometry, Raman scattering and Scanning Electron Microscopy (SEM). The phase composition of the films in dependence on conditions of treatment was analysed and have been shown that in slow and prolonged high-temperature process the low temperature binaries react completely and only Kesterite and ZnS is left. In addition, structural investigations by XRD have shown gradual decrease of crystallite sizes when the temperature level and duration of the high-temperature segment increases and respectively increase in the strain, due to formation of the phases in non-equilibrium conditions. In opposite, when the speed of dynamic segments in the process decreases the both crystallite size and strain of the Kesterite decreases non-monotonically. The grain sizes of Kesterite, presented by SEM investigations, have shown increase when the temperature and the duration increase, respectively the speed decreases with exemption at higher temperature near 750 C. The set of experiments gave idea by scrupulous analysis of Raman data to elucidate the track for fine manipulating of the defects in the structure of CZTS thin films having in mind the dependences of the ratios of Q = I287/I303 and Q’= I338/(I366+I374) on the process variables.

Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

The article discusses the results of investigations performed during a thermo-mechanical treatment of forgings made of chromium-molybdenum 42CrMo4 grade steel. The treatment was realized during a regular series production. The forging process was combined with a heat treatment carried out directly after forging on a specially adapted station. Such a production technology will make it possible to eliminate the step of repeated heating of the forgings. On the example of an element of a steering gear, it was demonstrated how it is possible to perform an isothermal annealing process starting from the temperature at which the trimming of the forgings ends. During the cooling of the forgings, it is enough to maintain the temperature at the proper level in order for the exothermal phase transformation of austenite into pearlite to take place. With an appropriate design of the processing line, the heat released during the transformation could be used to maintain the applied temperature, thus limiting the consumption of energy needed to power the devices. The test results show that, with the properly selected temperature of isothermal annealing, it is possible to obtain an equilibrial ferritic-pearlitic structure in the required hardness scope. Introducing such a solution into the industrial practice would allow significant savings of the energy used for the heat treatment.

The study presents the effect of annealing process parameters on the microstructure, hardness and strain hardening coefficients i.e., the strength coefficient c and the strain hardening exponent n, of 42CrMo4 steel. Seven selected annealing time-temperature schemes are examined for superior steel formability in cold metal forming conditions. The c and n coefficients are first determined in experimental upsetting of annealed samples and then used in FEM simulations of the upsetting process. The results demonstrate that the strain hardening coefficients (c and n) depend on the employed annealing scheme. Compared to the as-received sample, the annealing process reduces the true stress and effectively decrease the hardness of 42CrMo4 steel, improves microstructural spheroidization and, consequently, facilitates deformability of this material. The annealing schemes relying on heating the material to 750 °C and its subsequent slow cooling lead to the highest decrease in hardness ranging from 162 to 168HV. Results obtained with the SEM-EDS, LOM and XRD methods lead to the conclusion that the employed heat treatment schemes cause the initial ferritic-pearlitic microstructure to develop granular and semi-lamellar precipitation of cementite enriched with Mo and Cr in the ferrite matrix. In addition, the annealing process affects the growth of α-Fe grains. The highest cold hardening rate, and thus formability, is obtained for the annealing scheme producing the lowest hardness. The results of FEM simulations are positively validated by experimental results. Obtained results are crucial for further numerical simulations and experimental research connected with developing new cold metal forming methods for producing parts made of 42CrMo4 steel.

Porous graphite was prepared without the use of template by rapidly heating the carbonization products from mixtures of anthracene, flourene, and pyrene with a CO₂ laser. Rapid CO₂ laser heating at a rate of 1.8 × 10 ⁶ °C/s vaporizes out the fluorene-pyrene derived pitch while annealing the anthracene coke. The resulting structure is that of graphite with 100 nm spherical pores. The graphitizablity of the porous material is the same as pure anthracene coke. Transmission electron microscopy revealed that the interface between graphitic layers and the pore walls are unimpeded. Traditional furnace annealing does not result in the porous structure as the heating rates are too slow to vaporize out the pitch, thereby illustrating the advantage of fast thermal processing. The resultant porous graphite was prelithiated and used as an anode in lithium ion capacitors. The porous graphite when lithiated had a specific capacity of 200 mAh/g at 100 mA/g. The assembled lithium ion capacitor demonstrated an energy density as high as 75 Wh/kg when cycled between 2.2 V to 4.2 V.

Abstract: COVID-19 Long Haulers, an estimated 3% to 12% of people infected globally with coronavirus having latter devasting symptoms 12 weeks after the initial infection is on the rise. We conducted a collaborative study with the long covid patient organization in Greece in order to estimate the prevalence, symptoms and problems that adult long haulers experience and then propose a management plan for these patients. Symptoms were obtained from 208 patients using unstructured qualitative free text entries in an anonymized online questionnaire. The majority of respondents (68.8%) were not hospitalized and had been diagnosed more than six months ago with lingering symptoms (66,8%). Eighteen different symptoms (fatigue, tachycardia, shortness of breath, parosmia etc) were mentioned in both hospitalized and community patients. Interestingly, patients with initial mild symptoms suffer from the same persistent symptoms as those who were hospitalized. Awareness of long covid sequelae seems to be low even among medical doctors. Treatment options incorporating targeted rehabilitation programs are either not available or still excluded from the management plan of long covid patients. Since long COVID is a multi-systemic entity, we propose a holistic interventional approach using a multidisciplinary medical team in order to securely and effectively diagnose and treat these specific patients. Academic and medical community must collaborate with long covid patients’ organizations so as to provide personalized medicine.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

An addition sequence is an important operation in many applications of computer science, such as multi-modular exponentiation and outsourcing protocols. Finding an addition sequence for a set of positive integers with the shortest length is challenging due to the high computational time required to find the solution. In this paper, a new metaheuristic algorithm is designed based on the simulated annealing strategy to generate a short addition sequence. The efficiency of the proposed algorithm was proved experimentally by comparing it with the previous exact and heuristic algorithms in terms of running time and the length of the addition sequence.

The spectrums of one type of object under different conditions have the same features (up, down, protruding, concave) at the same spectral positions, which can be used as primary parameters to evaluate the difference among remotely sensed pixels. Wavelet-feature correlation ratio Markov clustering algorithm (WFCRMCA) for the remotely sensed data is proposed based on an accurate description of abrupt spectral features and an optimized Markov clustering in the wavelet feather space. The peak points can be captured and identified by applying a wavelet transform to spectral data. The correlation ratio between two samples is a statistical calculation of the matched peak point positions on the wavelet feature within an adjustable spectrum domain or a range of wavelet scales. The evenly sampled data can be used to create class centers, depending on the correlation ratio threshold at each Markov step, accelerating the clustering speed by avoiding the computation of Euclidean distance for traditional clustering algorithms, such as K-means and ISODATA. Markov clustering applies several strategies, such as a simulated annealing method and gradually shrinking the clustering size, to control the clustering convergence. At each clustering tempera-ture, it can obtain the best class centers quickly. The experimental results of the Airborne Visible/ Infrared Imaging Spectrometer (AVIRIS) and Thermal Mapping (TM) data have verified its ac-ceptable clustering accuracy and high convergence velocity.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

In the present study, a nanostructured FeAl coating was prepared by cold spraying of ball milled powder. Annealing treatment was applied to the coating to investigate its effect on the microstructure, phase structure and microhardness of the cold-sprayed nanostructured FeAl coating. The results showed that the FeAl phase was kept unchangeable when the coating annealed at the temperature above 500oC. Annealing temperature significantly influenced the microstructure and microhardness of cold-sprayed FeAl coating. With raising annealing temperature, the lamellar structure in the as-sprayed coating disappeared and a dense coating microstructure with fully bonding of deposited particles at their interfaces was achieved after annealing at 950oC. Nanograin growth of the FeAl phase occurred at an annealing temperature higher than 800oC. The microhardness of cold-sprayed FeAl coating remained about 400 Hv0.1 at the annealing temperature below 800oC and decreased to 300 Hv0.1 at 1100oC.

Bearings are widely used in various types of electrical machinery and equipment. As their core components, failures will often cause serious consequences . At present, most methods of parameter adjustment are still manual adjustment of parameters. This adjustment method is susceptible to prior knowledge and easy to fall into the local optimal solution, failing to obtain the global optimal solution and requires a lot of resources.Therefore, this paper proposes a new method of bearing fault diagnosis based on wavelet packet transform and convolutional neural network optimized by simulated annealing algorithm.The experimental results show that the method proposed in this paper has a more accurate effect in feature extraction and fault classification compared with traditional bearing fault diagnosis methods. At the same time, compared with the traditional artificial neural network parameter adjustment, this paper introduces the simulated annealing algorithm to automatically adjust the parameters of the neural network, thereby obtaining an adaptive bearing fault diagnosis method. To verify the effectiveness of the method, the Case Western Reserve University bearing database was used for testing, and the traditional intelligent bearing fault diagnosis method was compared. The results show that the method proposed in this paper has good results in bearing fault diagnosis. Provides a new way of thinking in the field of bearing fault diagnosis in parameter adjustment and fault classification algorithms

In the present study, we investigate the post-editese phenomenon, i.e., the unique features that set machine translated post-edited texts apart from human-translated texts. We use two literary texts, namely, the English children's novel by Lewis Carroll Alice’s Adventures in Wonderland (AW) and Paula Hawkins' popular book The Girl on the Train (TGOTT) translated from English into Brazilian-Portuguese to investigate whether the post-editese features can be found on the surface of the post-edited (PE) texts. In addition, we examine how the features found in the PE texts differ from the features encountered in the human-translated (HT) and machine translation (MT) versions of the same source text. Results revealed evidence for post-editese for TGOTT only with PE versions being more similar to the MT output than to the HT texts.

Conventional models do not fully explain composition of the solar system – for example, the presence of p-nuclei and post-post-Fe-nuclei remains not yet understood (and is one of the great unresolved puzzles of nuclear astrophysics in general); other puzzles exist. We offer a hypothesis which can explain the appearance of non-native elements in the solar system, and a feasible scenario for its implementation. The hypothesis suggests that a nuclear-fission "event" occurred in the inner part of the solar system at the time currently defined as the birth of the system. Conventional models have never considered fission as a contributing nuclei-production mechanism. Upon examination of the existing models and factual data (presented in volumes of publications but never combined into an aggregate), we identified one plausible scenario by which a fission event (not demolishing the entire solar system) could occur: an encounter with a compact super-dense stellar "fragment" (with specific properties) and its "explosion" in fission-cascades. Such scenario also helps resolve other long-standing puzzles of the solar system. For example, it provides that the fission-produced nuclei subsequently transformed into the material that (eventually) accreted into the "rocky" objects in the system (terrestrial planets, asteroids, etc.) and enriched the pre-existed hydrogen-helium objects (the Sun and the gaseous giants) – this offers an explanation for the planets’ inner position and compositional differences within the predominantly hydrogen-helium rest of the solar system. Other implications also follow.

In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’)  A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite  austenite transformation in the same temperature range.

Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

The present work sets out the evaluation of composite laminates through optimization objective functions. Genetic Algorithms (GA), as well as Simulated Annealing (SA), were performed in order to determine the optimal ply orientations of a fiber-reinforced polymer laminate for three given load cases: 1) in-plane loads, 2) combined moments, and 3) in-plane loads and combined moments. It searches the optimal orientation layup, which fulfills at the same time both the maximum strain criterion and the Tsai-Wu failure criterion. Construction of an objective function based on the strains and the stresses involves a minimization process to deformations and a maximization of the safety factor. For the first load case, the initial solution is [±45/0/90/±45]s, and the best solution is [(45/135)2/452]s. For the second load case, [-45/45/45/-45/0/90]s is the initial layup sequence, then the best solution obtained is [(45/-45)2/452]s, where plies at 0° and 90º are not necessary even when axial loads are applied. For the third study case, the original layup sequence is [0/45/-45/45/0/90]s; meanwhile, the best solution calculated is [21/24/145/140/45/49]s. An interesting observation is that each pair of layers has a 5º gap. The simulations show that the qualitative results from the GA are better than the SA, but with a significantly higher computational cost. These kinds of computational tools are expected to be used as a reference guide for an optimal fiber configuration with respect to the common orientations used when composite laminates are designed for a structural application.

Nano- and micro-sized CeO2 surface layers based on titanium alloy TiAl6V4 were obtained by magnetron sputtering with or without subsequent annealing. The structure of the samples was determined using scanning electron microscopy, Auger electron spectroscopy, energy dispersive spectroscopy, and X-ray diffraction. Hardness was measured by sclerometry. A direct linear dependence of the thickness of the surface layers on the deposition time and an extreme dependence, passing through a maximum, on the power are shown. A decrease in hardness with an increase in the thickness of the cerium oxide coating was noted. An increase in surface roughness, delamination and loosening of the surface layer, presumably associated with annealing, were noted. In samples with a surface layer thinner than 715 nm without annealing and 750 nm after annealing, the formation of a sublayer of TiO2, Al2O3, and Ce(VO4) was found, and in annealed samples with a layer length of less than 300 nm, all cerium dioxide reacted with vanadium dioxide to form vanadate.

In recent decades, there have been numerous endeavors to develop a novel category of survival distributions possessing enhanced flexibility through the extension of existing distributions. This article constructs and validates the statistical properties of a novel survival distribution in order to obtain an alternative distribution that is suitable for analyzing survival data by presenting the novel mixture of the Fréchet distribution along with statistical properties such as the probability density function (PDF), cumulative distribution function (CDF), rth ordinary moment, skewness, kurtosis, moment-generating function, mean, variance, mode, survival function, hazard function, and asymptotic behavior, as well as constructing the estimators of the unknown parameter by employing the expectation-maximization (EM) algorithm, and simulated annealing. Additionally, the performance of the proposed estimators was compared with bias, mean squared errors (MSE), and simulated variances, and given an illustrative example of the proposed distribution to the survival data set in order to show that the proposed distribution is appropriate for the right-skewed data. This will be extremely advantageous in survival analysis.

Wireless sensor networks (WSN) are mostly utilized in many applications. Indeed, WSN is composed of sensors to evaluate some physical phenomena. However, the information brought by the sensor still missed if we don't know the exact location of the event. Several localization algorithms have been proposed in order to locate the nodes in WSN. The localization algorithms are categorized into range-based and range-free techniques. The range-based techniques use either distance or time to calculate the coordinates of unknown nodes. Nevertheless, those kinds of techniques need some additional material in computation purpose. Therefore, range-based techniques present an expensive solution for positioning in WSN. Alternatively, range-free techniques may do the same task without involving additional material. But they don’t offer a high precision of localization in comparison with range-based techniques. DVHOP is the most popular range-free technique that uses the hop count method in the localization process. In this work, we propose an improvement of DVHOP localization algorithm to create three improved versions of this algorithm and we have achieved that by adopting two meta-heuristic (simulated annealing, particle swarm optimization) and FMINCON solver dedicated to the optimization in the field of WSN nodes localization. The experimental results obtained in this work show clearly the gain and the good impact of our proposition.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

We present a very computationally light and fast approximation algorithm and then verify it with genetic algorithm and simulated annealing. We show that our algorithm is on par with GA and SA in terms of output produced while having a tightly bounded time complexity. Our algorithm works best when there is a strong positive correlation between the reliability of a component and its cost. We present two algorithms with the same essence. One of them is system cost bounded and the other is target reliability bounded. Our proposed algorithm works on a subsystem level redundancy instead of component level redundancy.

Post-ovulatory aging (POA) is an inevitable factor during some assisted reproduction technology procedures, and results in poor fertilization rates and impaired embryo development. This study used RNA sequencing analysis and experimental validation to study the similarities and differences between in vivo- and in vitro-matured porcine oocytes before and after POA. Differentially expressed genes (DEGs) between fresh in vivo-matured oocyte (F_vivo) and aged in vivo-matured oocyte(A_vivo) and DEGs between fresh in vitro-matured oocyte (F_vitro) and aged in vitro-matured oocyte(A_vitro) were intersected to explore the co-effects of POA. It was found that "organelles", especially "mitochondria", were significantly enriched GO terms. The expression of genes related to the “electron transport chain” and “cell redox homeostasis” pathways related to mitochondrial function significantly showed low expression patterns in both A_vivo and A_vitro groups. WGCNA analysis to explore gene expression modules specific to A_vivo. Trait-modules association analysis showed that the red modules were most associated with in vivo aging. There are a total of 959 genes in the red module, which are mainly enriched in “RNA binding”, “mRNA metabolic process”, etc. GO terms, and “spliceosome” and “nucleotide excision repair” pathways. DNAJC7, IK, and DDX18 were at the hub of the gene regulatory network. And these genes were all expressed higher in A_vivo. In summary, POA affects the organelle function of oocytes. A_vivo oocytes have some unique gene expression patterns. These genes may be potential anti-aging targets. This study helps us understand the detailed mechanism of POA and provides strategies for researching oocyte aging.

Background: Patients with burn scars often suffer from a ‘vicious cycle’ in which their skin becomes dry and pruritus. This greatly reduces patients' quality of life, but there is no well-known mechanism yet, and the development of drugs for effective treatment is necessary. Objective: This study evaluated the efficacy and safety of cosmetic formulation containing arginine glutamate ion pair (named as RE:pair) on epidermal barrier function and reducing pruritus. Materials and Methods: A total of 20 patients [15 male and 5 female; average age 48.35 ± 13.13 years] participated in evaluating the effectiveness of using the RE:pair formula topically twice daily for up to 4 weeks after burn pruritus. Treatment efficacy was evaluated by Numerical Rating Scale (NRS) for itching and pain, transepidermal water loss (TEWL), skin hydration, Vancouver Scar Scale (VSS) evaluation, and the patient’s overall satisfaction. Results: This formula was well-tolerated, with significant relief of NRS for itching and pain score after 2nd weeks and 4th weeks of application (p < 0.05). The itching score was high in some patients, and overall, it decreased significantly after 4 weeks compared to before application. Also, the personal pain score decreased after 4th weeks. Overall TEWL showed 35 % improvement after 4th week, and 52 % improvement was confirmed in arms and 19 % in legs. The overall improvement effect of skin hydration was also 45 % (p = 0.0012), and the improvement effect was 40 % (p = 0.0371) in areas including arms and 54 % (p = 0.0313) in areas including legs. All patient satisfactory evaluations were "excellent". Conclusions: RE:pair formula was safe and effective in improving skin barrier and itch relief, and if further studies are conducted, it can be used as an excellent topical treatment for post-burn scar that strengthens the skin barrier.

Open pit mining is a common activity in the Yucatan peninsula for the extraction of limestone. This mining is known under the generic name of quarries, and regionally as sascaberas (sascab=white soil in Mayan language). These areas are characterized by the total removal of the natural vegetation cover and soil in order to have access to the calcareous material. The present study shows the composition and structure of the vegetation in five quarries after approximately ten years of abandonment, and the conserved vegetation near to each one of the quarries in southeastern Quintana Roo. Using a canonical correspondence analysis (CCA), the distribution of the species was determined in relation to the edaphic variables: soil depth, percentage of organic matter (OM), cationic exchange capacity (CEC), pH and texture. 26 families, 46 genera and 50 species were recorded in the quarries and 25 families, 45 genera and 47 species were recorded in the conserved areas. The dominant species in the quarries belong to the families Poaceae, Fabaceae, Rubiaceae and Anacardiaceae. The quarries with higher values of OM (1.63%), CEC (24.05 Cmol/kg), depth (11 cm) and sand percentage (31.33%) include the following species like Lysiloma latisiliquum, Metopium brownei and Bursera simaruba which are commonly found in secondary forests. On the other hand, quarries with lower values of OM (0.39%), CEC (16.58 Cmol/kg) and depth (5.02), and higher percentage of silt (42.44%) were dominated by herbaceous species belonging to the Poaceae family and by Borreria verticillata, which are typical in disturbed areas of southeastern Mexico. In all cases, the pH was slightly alkaline due to the content of calcium carbonate (CaCO3), characteristic of the soils of the region. The edaphic variables are significantly correlated with the development and distribution of vegetation, and with the structure of the communities.

Modern power system integrates more and more new energy and use a large number of power electronic equipment. This makes it face more challenges in online optimization and real-time control. Deep reinforcement learning(DRL) has the ability of processing big data and high-dimensional features, as well as the ability of independently learning and optimizing decision-making in complex environments. In this paper, we explore DRL based online combination optimization method of grid section for large complex power system. In our method, to improve the convergence speed of the model, we propose to discretize the output action of the unit and simplify the action space. We also design a reinforcement learning loss function with strong constraints to further improve the convergence speed of the model and facilitate the algorithm to obtain the stable solution. Moreover, to avoid the local optimal solution problem caused by the discretization of the output action, we propose to use the annealing optimization algorithm to make the granularity of the unit output finer. We verify our method on IEEE 118-bus system. The experimental results show that our model has fast convergence speed and better performance, and can obtain stable solutions.

Ultra-short laser pulses (1030 nm/230 fs) were used to laser ablate surface of crystalline sapphire. Laser ablated patterns were annealed at high temperature 1500∘C. Surface reconstruction took place removing ablation debris field at the edges of ablated pits in oxygen flow. Partial reconstruction of ripples was also observed.

We studied the effect of annealing and the applied magnetic field from 50 Oe to 20 kOe on the magneto-structural behavior of Ni2FeSi-based Heusler microwires fabricated by using Taylor-Ulitovsky technique. Using the XRD analysis, a strong effect of annealing, manifested as the development of the crystallization process, was observed. The average grain size and crystalline phase content of annealed sample increase from 21.3 nm and 34 % to 32.8 nm and 79%, respectively, as-compared to the as-prepared one. In addition, upon annealing phase transforms into a monoclinic martensitic structure with modulation 10M were observed, which cannot be found in the as-prepared sample. Concerning the magnetic properties, both samples show ferromagnetic behavior below and above the room temperature, where the Curie temperature of Ni2FeSi is higher than room temperature. The induced secondary phases have a noticeable effect on the magnetic behavior of the annealed sample, where a high normalized saturation magnetization (NMs) and low normalized reduced remenance (Mr = M/M5K), compared to the as- prepared have been detected. Additionally, the coercivity of annealed sample shows one flipping point at 155 K where it behavior with temperature is changed. Meanwhile, the as-prepared sample show two flipped point at 205 K and 55 K. A mismatch between field cooling (FC) and field heating (FH) magnetization curves with temperature has been detected for annealed sample at low applied magnetic field. In addition the FC and FH curves shows different slopes with variation the temperature and the magnetic field. By increasing the external magnetic field higher than 200 Oe and up to 20 kOe a gradual changing in the magnetic behavior has been detected, where the mismatch and different slopes disappeared at applying magnetic field about 20 kOe. The difference in magnetic and structure behavior of Ni2FeSi microwires sample is discussed considering the effect of induced internal stresses by the presence of a glass coating and the recrystallization and stresses relaxation upon annealing.

Metaheuristic algorithms have been frequently using to tackle optimization problems, however such algorithms in the analysis of health-related data is not commonly used as developing metaheuristic algorithms that work well on health-related data is a difficult task due to complexity of the health data in particular genomics and epigenetics data. One of the important tasks in genomics is to predict genomic elements that are incorporating together to regulate a disease-related genes. Predicting such elements are important as they can be used to develop a personalized cure. In this study, we present for the first time, a multi-object simulated annealing algorithm to identify enhancer-promoter like interactions from Hi-C (chromosome conformation capture) data. These regulatory elements can potentially play vital roles as promoters and/or enhancers in appearance and exacerbation of the regulation of gene.s To evaluate the efficiency of the proposed method, we applied our proposed method and traditional methods on the Hi-C data from mice and compared together. Our results show that the interacting elements identified by our new method are more likely to be functional. The source code of the method is publicly available.

This work focuses on expressing the TSP with Time Windows (TSPTW for short) as a quadratic unconstrained binary optimization (QUBO) problem. The time windows impose time constraints that a feasible solution must satisfy. These take the form of inequality constraints, which are known to be particularly difficult to articulate within the QUBO framework. This is, we believe, the first time this major obstacle is overcome and the TSPTW is cast in the QUBO formulation. We have every reason to anticipate that this development will lead to the actual execution of small scale TSPTW instances on the D-Wave platform.

Previous studies suggested that trauma-focused cognitive behavior therapy (TF-CBT) is effective in reducing symptoms of post-traumatic stress disorder (PTSD) and depression in children and adolescents. However, the effects of app-assisted TF-CBT-based interventions in psychiatric clinics compared to treatment-as-usual (TAU) are under-explored. The purpose of this study was to reveal the added value of the app-assisted TF-CBT-based intervention as an add-on to TAU. The digitalized measures of the Child and Adolescent Trauma Screen (CATS), The Adolescent Dissociative Experience Scale (A-DES), Short Moods and Feelings Questionnaire (SMFQ), PTSD Checklist (PCL-5), and Children's Post-Traumatic Cognitions Inventory (CPTCI) were applied at baseline and post-treatment. The app-assisted TF-CBT-based group participants started with higher levels of negative alterations in cognition and mood compared to TAU participants but at post-treatment, no significant differences were observed between the app-assisted TF-CBT and TAU groups. Within the app-assisted TF-CBT group, post-treatment scores were significantly lower in post-traumatic stress symptoms, intrusion symptoms, alterations in arousal and reactivity, overall post-traumatic cognitions, and belief in being "a fragile person in a scary world”. Within the TAU group, post-treatment scores were notably lower just in dissociation and intrusion symptoms. The study suggests that app-assisted TF-CBT-based intervention can be effective in addressing specific trauma-related symptoms. The findings imply the necessity for screening for traumatic experiences, incorporating trauma-informed care, implementation of TF-CBT into treatment protocols, utilization of app-assisted interventions, tailoring interventions to individual needs, and comprehensive assessment and monitoring of treatment progress.

Background: This study aimed to examine the course of Depression and anxiety in COVID-19 survivors with a psychiatric history compared with those without a psychiatric history. Methods: A web-based cross-sectional survey for COVID-19 survivors was conducted from July to September 2021. 6016 COVID-19 survivors, the accuracy of whose responses was determined to be assured, were included in analyses. Exposures included psychiatric history and time since COVID-19 infection, and the main outcomes and measures included severity of depression and anxiety, as assessed using the Patient Health Questionnaire-9 (PHQ-9) and Generalized Anxiety Disorder-7 (GAD-7), respectively. Results: Mean severity of PHQ-9 and GAD-7 were significantly higher in participants with a psychiatric history than in those without a psychiatric history. Two-way analysis of covariance for PHQ-9 showed a significant main effect of the presence of psychiatric history and a significant interaction effect of psychiatric history × time since infection. Two-way analysis of covariance for the GAD-7 score revealed a significant main effect of the presence of psychiatric history and time since COVID-19 infection and the interaction effect of these factors. Conclusions: The course of depression and anxiety was more severe in COVID-19 survivors with a psychiatric history than in those without a psychiatric history.

Direct and indirect effects after mine operations cease must ideally be subject to perpetual monitoring routines in order to detect possible risks or avoid adverse effects on the surrounding ecosystems at an early stage. In this contribution, mining subsidence lakes created inside the nature reserve Kirchheller Heide and Hilsfeld Forest are subjected to analysis for a long-term monitoring scheme. For this purpose, we employ high-resolution unmanned aerial system (UAS)-based multispectral and thermal mapping tools to provide a fast, non-invasive and multitemporal environmental monitoring method. Specifically, we propose to monitor vegetation evolution through multispectral analysis, biotypes identification using machine learning algorithms, and water surface extent detection, together with their thermal behavior. The aim of this contribution is to present the proposed workflow and first results to establish a baseline for future analyses and subsequent surveys for longterm multi-temporal monitoring

Collaboration among individuals with diverse skills and personalities is crucial in producing high-quality software. The success of any software project depends on the team’s cohesive functionality and mutual complementation. This study introduces a data-centric methodology for forming Software Engineering (SE) teams centred around personality traits. Our study analyzed data from an SE course where 157 students in 31 teams worked through four project phases and were evaluated based on deliverables and instructor feedback. Using the Five Factor Model (FFM) and a variety of statistical tests, we determined that teams with higher levels of extraversion and conscientiousness and lower neuroticism consistently performed better. We examined team member interactions and developed a predictive model using extreme gradient boosting. The model achieved a 74% accuracy rate in predicting inter-member satisfaction rankings. Through graphical explainability, it underscored incompatibilities among members, notably those with differing levels of extraversion. Based on our findings, we introduce a team formation algorithm using Simulated Annealing (SA), built upon the insights from our predictive model and additional heuristics.

In this paper, a Markov random field model is proposed to determine a site’s light pollution risk level. The specific data of 12 indicators of five typical cities in China is first collected to establish a hierarchical indicator system using an R-type clustering algorithm. Then, the entropy weight method is used to filter, determine 10-factor indicators, three potential impact indicators, and a light pollution risk index, and establish an undirected probability map model. A light pollution measurement based on Markov random field is obtained, and a location-based light pollution risk assessment index (LBLPRAI) is proposed. LBLPRAI of different types of sites is analyzed, and three possible intervention strategies are proposed to solve the light pollution problem: road lighting system planning, increasing vegetation coverage, and building system planning. Finally, the simulated annealing algorithm is used to determine the best intervention strategy, and it is concluded that the use of strategy 1 in the urban community 2 is the most effective measure, which can reduce the risk level of light pollution by 17.2%.

In this paper, in order to provide proper parameters for the preparation of semi-solid billets, the semi-solid annealing of hot-rolled 2A14 Al alloy was investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) with X-ray energy dispersive spectrometer (EDS) and electron backscattered diffraction (EBSD), scanning transmission electron microscope (STEM). XRD results show that with the increase of temperature, equilibrium θ-Al2Cu gradually dissolved in the matrix. The EDS results of SEM and STEM show that there were coarse θ-Al2Cu phase, ultra-fine precipitate Al(MnFeSi) or (Mn, Fe)Al6 phase and atomic clusters in the microstructure. EBSD results show that the recrystallization mechanism was dominated by continuous static recrystallization (CSRX), the homogeneous nucleation occurred when the sample was heated to near solidus temperature, and CSRX happened in the semi-solid temperature. In the process of recrystallization, the micro-texture changed from preferred orientation to random orientation. A variety of experimental results show that static recrystallization (SRX) occurred at semi-solid temperature due to the blocking effect of atomic clusters on dislocation slip and the Zener drag effect of fine precipitates on low angle grain boundaries (LAGBs) disappeared with melting at semi-solid temperature.

Several biomedical products, like scaffolds, implants, prostheses, and orthoses, require materials having superior physicochemical and biological properties. Polyethylene terephthalate glycol (PETG) is being increasingly used for various biomedical applications. There are a few studies on PETG-based composites, however, natural fibers like silk short fibers reinfored PETG composites have not been attempted. Being a cost-effective widely available material, PETG-Silk combination can be potential biocomposite for several biomedical applications. Here, we report a novel short silk fiber reinforced PETG composite prepared by a wet-mixing route, ensuring homogenous dispersion of the filler. Different ratios (2-10%) of short silk fibers were used to prepare composites with varied compositions. The mechanical, physicochemical, and biological properties of the prepared composites were analyzed. Thermogravimetric analysis showed that such composites are thermally stable up to 390 °C and can be used for thermal extrusion-based manufacturing. The tensile modulus of the samples increased with fiber content; however, the failure strain reduced with fiber content. Furthermore, upon annealing, the tensile modulus increased but, the failure strain of the composites decreased, XRD study revealed that heat treatment has altered the crystalline nature of the composites. Finally, we evaluated the cytocompatibility of the prepared composites to assess their suitability for various biomedical applications.

We propose a new binary formulation of the Travelling Salesman Problem (TSP), with which we overcame the best formulation of the Vehicle Routing Problem (VRP) in terms of the minimum number of necessary variables. Furthermore, we present a detailed study of the constraints used and compare our model (GPS) with other frequent formulations (MTZ and native formulation). Finally, we have carried out a coherence and efficiency check of the proposed formulation by running it on a quantum annealing computer, D-Wave\_2000Q6.

The optimization problem of two or more special-purpose functions of the energy system is subjected to an analysis. Based on experience of our research and general knowledge of partial solutions of energy system optimization at the level of control of production and power energy supply by energy companies in the Czech Republic, a special-purpose (cost) function has been defined. By analysing the special-purpose function, penalty and limitations have been defined. Using the fuzzy logic, a set of suitable solutions for the special-purpose function is accepted. An optimum of the special-purpose function is looked for using the simulated annealing method. The history of electricity consumption is sorted by day and by hour, representing the multidimensional data. When using the cluster analysis, type daytime diagrams of consumption are defined. Type daytime diagrams form prototypes of identified clusters. The so-called self-organizing neural network with Kohonen map attached is used to perform the cluster analysis. The result of our research is presented by an experiment.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

This paper presents an extension of the resuts obtained in previous work by the author concerning the application of global optimization techniques to the design of finite strategic games with mixed strategies. In that publication the Fuzzy ASA global optimization method was applied to many examples of synthesis of strategic games with one previously specified Nash equilibrium, evidencing its ability in finding payoff functions whose respective games present those equilibria, possibly among others. That is to say, it was shown it is possible to establish in advance a Nash equilibrium for a generic finite state strategic game and to compute payoff functions that will make it feasible to reach the chosen equilibrium, allowing players to converge to the desired profile, considering that it is an equilibrium of the game as well. Going beyond this state of affairs, the present article shows that it is possible to "impose" multiple Nash equilibria to finite strategic games by following the same reasoning as before, but with a slight change: using the same fundamental theorem of Richard D. McKelvey, modifying the original prescribed objective function and globally minimizing it. The proposed method, in principle, is able to find payoff functions that result in games featuring an arbitrary number of Nash equiibria, paving the way to a substantial number of potential applications.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Premortem clinical diagnoses and postmortem autopsy findings do not match throughout history. These clinicopathological discrepancies are expected to be raised during the coronavirus disease 2019 (COVID-19) pandemic due to increased pressure on healthcare. At the same time, autopsies and clinicopathological discrepancies accurately display the quality of the healthcare system. To assess that, we examined the relevant works of literature according to the PRISMA-based protocol. As discrepancy rate changes in the correlation to the length of stay in the hospital, we also checked whether studies with patients from the intensive care unit (ICU) differed in discrepancies significantly. We found overall risk differences pretty much alike in "pre-COVID" and "during the pandemic" groups of studies. Based on that, we concluded that healthcare quality did not drop significantly during the pandemic. Be it as it may, the pandemic exposed some shortcomings in mortem healthcare regarding consensus to the autopsy, organ retention, burial, and the postponed burial or the digitalization of post mortem healthcare. All of these issues should be addressed in the future.

The embryonic epicardium originates from the proepicardium, an extracardiac primordium constituted by a cluster of mesothelial cells. In early embryos, the embryonic epicardium is characterized by a squamous cell epithelium resting on the myocardium surface. Subsequently, it invades the subepicardial space and thereafter the embryonic myocardium by means of epithelial-mesenchymal transition. Within the myocardium, epicardial-derived cells present multilineage potential, later differentiating into smooth muscle cells and contributing both to coronary vasculature and cardiac fibroblasts in the mature heart. Over the last decades, we have progressively increased our understanding of those cellular and molecular mechanisms driving proepicardial/embryonic epicardium formation. This study provides a state-of-the-art review of the transcriptional and emerging post-transcriptional mechanisms involved in the formation and differentiation of the embryonic epicardium.

Background: Whilst lack of concentration is a known symptom of anaemia, its association with post-stroke dementia is unclear. Methods: We used data from a UK regional stroke register. To be eligible, patient must have survived to discharge and had anaemia by WHO criteria. Dementia status and other prevalent co-morbidities were assessed using ICD-10 codes. Patients were followed till May 2015 (mean follow-up 3.7 years, total person years = 27,769). Hazard Ratio for incident dementia was calculated using Cox-proportional hazards model controlling for potential confounders. Fine and Gray model was additionally constructed using mortality as the competing risk. Results: A total of 7,454 stroke patients were included with mean age (SD) of 75.9(12.3) years (50.2% men). Those with anaemia were older, has higher disability and co-morbidity burden prior to stroke. We observed a large amount of variation in the dementia incidence rates over time and that the hazard ratio increased every year. The significant association between anaemia and dementia incidence was lost after controlling for pre-stroke Modified Rankin score (HR1.17(0.97,1.40)). With every 20g/dL increase in Hb was associated with a significant reduction in the risk of dementia after adjustment for age, sex, stroke factors and disability but lost significance after adjustment for vascular risk factors. Competing risk analyses showed similar results. Conclusion: Whilst we found no evidence of anaemia as a risk factor for post-stroke dementia, the findings may be limited by potential under recognition of post stroke dementia.

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we have employed Radio Frequency (RF) Sputtering of Zinc Oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 minutes, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400°C for 10 minutes, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70 times and a photocurrent increase of 13.86 times, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

The 11 system in iron-based superconducting family has become one of the most extensively studied materials in the research of high-temperature superconductivity due to their simple structure and rich physical properties. However, the research on 11 iron-based superconductors faces numerous obstacles, mainly stemming from the challenges associated with producing high-quality single crystals. Since the discovery of FeSe superconductivity in 2008, researchers have made significant progress in crystal growth, overcoming the hurdles that initially impeded their studies. Consequently, they have successfully established the complete phase diagrams of 11 iron-based superconductors, including FeSe1-xTex, FeSe1-xSx and FeTe1-xSx. In this paper, we aim to provide a comprehensive summary of the preparation methods employed for 11 iron-based single crystals over the past decade. Specifically, we will focus on hydrothermal, chemical vapor transport (CVT), self-flux, and annealing methods. Additionally, we will discuss the quality, size, and superconductivity properties exhibited by single crystals obtained through different preparation methods. By exploring these aspects, we can gain a better understanding of the advantages and limitations associated with each technique.

A new variant of two-echelon routing problem is investigated, where the truck and the drone are used to cooperatively complete the deliveries of all parcels. The truck not only acts as a tool for parcel delivery, but also serves as a moving depot for the drone. The drone can carry several parcels and take off from the truck, while returning to the truck after completing the delivery. The energy consumption model for the routing process of the drone is analyzed, when it is utilized to deliver multiple parcels. A two-stage route-based modelling approach is proposed to optimize both the truck’s main route and the drone’s adjoint flying routes. A hybrid heuristic integrating nearest neighbor and cost saving strategies is developed to quickly construct a feasible solution. The simulated annealing algorithm is applied to improve the quality of the solution, where a Tabu list is employed to improve the search efficiency. Random instances at different scales are used to test the performance of the proposed algorithm. A case study based on the practical road network in Changsha, China, is presented, through which the sensitivity analysis is conducted with respect to some critical factors.

The Sars-Cov-2 pandemic led to several needed containing measures that conditioned the onset of depressive, anxiety and post-traumatic stress symptoms in population. These symptoms, espe-cially if not diagnosed and treated, can also occur in patients undergoing surgery with high im-pact on people’s lives, like hysterectomy. To evaluate the post-surgical distress and anx-ious-depressive symptoms following hysterectomy for benign disease focusing on the impact of COVID-19 pandemic. The prospective observational cohort study included patients undergoing hysterectomy for benign disease. Psychologic evaluation through social-demographic question-naires was obtained before surgery (T1), postoperatively (T2), and 3 months after surgery (T3). The HADS (Hospital Anxiety and Depression Scale) was used to evaluate anxious-depressive symptoms and the PCL-5 (Post-traumatic Stress Disorder Checklist for DSM-5) compared the on-set of post-surgical distress and anxiety and depressive symptoms. The pre-COVID-19 pan-demic period was compared to the post-COVID-19 pandemic phase. Patients treated after COVID-19 pandemic showed higher depressive symptoms rate compared to those treated before (p-value=0.02); conversely, pre-COVID-19 patients were more prone to develop a PTSD (p-value=0.04). A significative association between the occurrence PTSD and anxiety-depressive symptoms registered at T2 a (p-value=0.007) and T3 (p-value

Long COVID (LC) encompasses a constellation of long-term symptoms experienced by at least 10% of people after the initial SARS-CoV-2 infection, and so far has affected about 65 million people. The etiology of LC remains unclear; however, many pathophysiological pathways may be involved, including viral persistence; chronic, low grade inflammatory response; immune dysregulation and defective immune response; reactivation of latent viruses; autoimmunity; persistent endothelial dysfunction and coagulopathy; gut dysbiosis; hormonal dysregulation, mitochondrial dysfunction; and autonomic nervous system dysfunction. There are no specific tests for the diagnosis of LC, and clinical features including laboratory findings and biomarkers may not specifically relate to LC. Therefore, it is of paramount importance to develop and validate biomarkers that can be employed for the prediction, diagnosis and prognosis of LC and its therapeutic response. Promising candidate biomarkers that are found in some patients are markers of systemic inflammation including acute phase proteins, cytokines and chemokines; biomarkers reflecting SARS-CoV-2 persistence, reactivation of herpesviruses and immune dysregulation; biomarkers of endotheliopathy, coagulation and fibrinolysis; microbiota alterations; diverse proteins and metabolites; hormonal and metabolic biomarkers; as well as cerebrospinal fluid biomarkers. At present, there are only two reviews summarizing relevant biomarkers; however, they do not cover the entire umbrella of current biomarkers or their link to etiopathogenetic mechanisms, and the diagnostic work-up in a comprehensive manner. Herein, we aim to appraise and synopsize the available evidence on the typical laboratory manifestations and candidate biomarkers of LC, their classification based on main LC symptomatology in the frame of the epidemiological and pathogenetic aspects of the syndrome, and furthermore assess limitations and challenges as well as potential implications in candidate therapeutic interventions.

Chikungunya virus is a re-emerging mosquito-borne alphavirus. Outbreaks are unpredictable and explosive in nature. Fever, arthralgia, and rash are common symptoms during the acute phase. Diagnostic tests are required to differentiate chikungunya virus from other co-circulating arboviruses, as symptoms can overlap, causing a dilemma for clinicians. Arthritis is observed during the sub-acute and chronic phases, which can flare up, resulting in increased morbidity that adversely affects activities of daily living. During the 2019 chikungunya epidemic in Thailand, cases surged in Bangkok in the last quarter of the year. Here, we demonstrate the chronic sequelae of post-chikungunya arthritis in one of our patients 1 year after the initial infection. An inflammatory process involving edema, erythema, and tenderness to palpation of her fingers' flexor surfaces was observed, with positive chikungunya IgG and negative IgM tests and antigen. The condition produced stiffness in the patient’s fingers and limited their range of motion, adversely affecting daily living activities. Resolution of symptoms was observed with a short course of an anti-inflammatory agent. More research is required to determine whether sanctuaries enable chikungunya virus to evade the host immune response and remain latent, flaring up months later and triggering an inflammatory response that causes post-chikungunya arthritis.

Amorphous germanium films on non-refractory glass substrates were annealed by ultrashort near-infrared (1030 nm, 1.4 ps) and mid-infrared (1500 nm, 70 fs) laser pulses. Crystallization of germanium irradiated at a laser energy density (fluence) range from 25 to 400 mJ/cm2 under single-shot and multi-shot conditions was investigated using Raman spectroscopy. The dependence of the fraction of the crystalline phase on the fluence was obtained for picosecond and femtosecond laser annealings. The regimes of almost complete crystallization of germanium films over the entire thickness are obtained (from the analysis of Raman spectra with excitation of 785 nm laser). The possibility of scanning laser processing is shown, which can be used to create films of micro and nanocrystalline germanium on flexible substrates.

The market for microfluidic chips is experiencing significant growth; however, their development is hindered by a complex design process and low efficiency. Enhancing microfluidic chips’ design quality and efficiency has emerged as an integral approach to foster their advancement. Currently, the existing structural design schemes lack careful consideration regarding the impact of chip area, microchannel length, and the number of intersections on chip design. This inadequacy leads to redundant chip structures resulting from the separation of layout and wiring design. This study proposes a structural optimization method for microfluidic chips to address these issues utilizing a simulated annealing algorithm. The simulated annealing algorithm generates an initial solution in advance using the fast sequence pair algorithm. Subsequently, an improved simulated annealing algorithm is employed to obtain the optimal solution for the device layout. During the wiring stage, an advanced wiring method is used to designate the high wiring area, thereby increasing the success rate of microfluidic chip wiring. Furthermore, the connection between layout and routing is reinforced through an improved layout adjustment method, which reduces the length of microchannels and the number of intersections. Finally, the effectiveness of the structural optimization approach is validated through six sets of test cases, successfully achieving the objective of enhancing the design quality of microfluidic chips.

The problem of optimal scheduling in a system with parallel queues and a single server has been extensively studied in the queueing theory. However, such systems have mostly been studied by assuming homogeneous attributes of arrival and service processes, or in heterogeneous case a Markov random process was usually assumed. In this paper, we explore the possibility of combining simulation and neural network paradigms for optimal scheduling in a heterogeneous system with an arbitrary inter-arrival and service time distributions. The service of any queue by the server is exhaustive. Further routing of the server after the queue has been emptied is as instructed by the trained neural network. Any change in the queue that currently has a server is accompanied by a switching cost. The simulated annealing optimization algorithm which is used to optimize the parameters of the neural network was adapted for numerically evaluated average cost function. A Markov decision problem was formulated for the corresponding markovian queueing system to verify the results of solving the optimization problem. In addition to comparing the actual values of the average cost, the parameter values of the neural network trained on the optimal control policy of the Markov model are also used to determine the domains of parameters required for the simulated annealing defined on a finite discrete domain. Numerical analysis shows the effectiveness of this approach. Moreover, a comparison of the results for different distributions illustrates the insensitivity of the optimal control policy to the shape of the distributions for the same two first moments. Thus, the optimal control policy for an exponential model can be used as a suboptimal one for the general system.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

BACKGROUND This study investigated the association of postprandial plasma glucose (PPG) with cancer mortality using a general cohort of US adults. METHODS This cohort study included 14,860 US adults who attended the third National Health and Nutrition Examination Survey from 1988 to 1994, with mortality being followed up to December 31, 2019. The experimental exposures were levels of plasma glucose, including PPG with a fasting time of 0-3.9 h (PPG_0-3.9h) and 4-7.9 h (PPG_4-7.9h), plasma glucose with a fasting time ≥ 8 h (PG_fasting), and plasma glucose at 2 h after oral glucose tolerance test (PG_2hOGTT). Plasma glucose-associated cancer mortality risk was assessed using Cox proportional hazards models. RESULTS A 1-natural-log-unit increase in PPG_4-7.9h was associated with a higher multivariate-adjusted risk for cancer mortality [hazard ratio (HR), 3.24; 95% confidence interval (CI), 1.50-7.00]. However, PPG_0-3.9h, PG_fasting, PG_2hOGTT, hemoglobin A_1c, and insulin were not significantly associated with cancer mortality. The positive association of PPG_4-7.9h with cancer mortality remained in those without a prior diagnosis of cancer. CONCLUSIONS High PPG_4-7.9h is associated with a higher cancer mortality risk in US adults. Lowering PPG_4-7.9h may reduce cancer mortality.

Breast Angiosarcoma is a rare malignancy, accounting less than 1% of all soft tissue. It comprises primitive and secondary subtypes, such as radiogenic breast angiosarcoma (RAS). Despite the multimodal treatment, angiosarcomas represent an incurable disease for many patients and represent a cause of substantial deterioration of their quality of life. Surgery represents the cornerstone in the management, but high recurrence rates are reported. Electrochemotherapy (ECT) is practicable locoregional treatment in patients with advanced angiosarcoma, in a multimodal therapeutic strategy. ECT palliative benefit includes optimal patient compliance, good local hemostasis control, and local responses. Considering that only 22 cases are described in literature, we reported a rare case of RAS treated with ECT, after a multidisciplinary approach including Next Generation Sequencing (NGS). A literature review about the feasibility of ECT in RAS management was also performed.

Objectives: To examine the long term impact of COVID-19 on sleep patterns and development of sleep disorders. Methods: Using the centralized Massachusetts General Brigham (MGB) Research Patient Data Registry (RPDR), SARS-CoV2 positive patients were surveyed about their sleep patterns before and after the viral infection. Information related to co-morbid conditions and medications were obtained through chart review. Results: Two hundred and forty five completed surverys were analysed. Average age was 53.3 ± 16.3 years, and participants were predominantly Non-Hispanic White (84.1%) and female (74.3%). Average BMI (kg/m2) was 29.9 ± 6.9, and a greater proportion was non-smokers (63.2%). After COVID-19, there was an increase in the percentage of participants reporting difficulty initiating (31 ± 46% vs. 39 ± 49%, P=0.01), and maintaining sleep (43 ± 49% vs. 57 ± 49%, P<0.001), and use of sleep aids (24 ± 43% vs. 30 ± 45% P=0.003) with an incidence rate of 24.3%, 37.4%, and 12.3% respectively. In addition, there was an increase in daytime fatigue and the need for napping (58 ± 49% vs. 36 ± 48%, P <0.0001) with an incidence of 8% and 23% respectively. The sleep symptoms persisted beyond 12 months among 28% of the participants and were predominantly seen among women. Conclusions: Infection with SARS-CoV2 has negative effects on sleep, and a significant proportion of adults experience insomnia and daytime sleepiness beyond 12 months after recovering from the initial infection.

Despite the relative scarcity of studies focusing on pharmacotherapy in aphasia, there is evidence in the literature indicating that remediation of language disorders via pharmaceutical agents could be a promising aphasia treatment option. Among the various agents used to treat chronic aphasic deficits, cholinergic drugs have provided interesting results. In the current review, we focused on published reports investigating the impact of acetylcholine on language and further cognitive disturbances. It has been suggested that acetylcholine plays an important role in neuroplasticity and is related to several aspects of cognition, such as memory and attention. Moreover, cholinergic input is diffused to a wide network of cortical areas, which have been associated with language sub-processes. This could be a possible explanation for the positive reported outcomes of cholinergic drugs in aphasia recovery, and specifically in distinct language processes, such as naming and comprehension, as well as overall communication competence. However, evidence with regard to functional alterations in specific brain areas after pharmacotherapy is rather limited. Finally, despite the positive results derived from the relevant studies, cholinergic pharmacotherapy treatment in post-stroke aphasia has not been widely implemented. The present review aims to provide an overview of the existing literature in cholinergic pharmacotherapy interventions in post-stroke aphasia, following an integrated approach by converging evidence from neuroanatomy, neurophysiology, and neuropsychology.

Our understanding of Alzheimer’s disease (AD) pathogenesis has developed with several hypotheses over the last 40 years, including the Amyloid and Tau hypotheses, respectively. More recently, the p53 protein, well-known as ‘the guardian of the genome,’ has gained attention for its role in the early evolution of AD. This is due to p53’s central role in the control of oxidative stress and potential involvement in both Amyloid and Tau pathways. p53 is commonly regulated by post-translational modifications (PTMs), which affect its conformation, increasing its capacity to adopt multiple structural and functional states, including those that can influence several processes in AD. The following review will explore the impact of p53 post-translational modifications (PTMs) on its function and consequential involvement in AD pathogenesis.

Abstract Objectives To assess the causes and risk factors of posttraumatic stress disorder (PTSD) in adult asylum seekers and refugees. To explore whether the causes and risk factors of PTSD, between male and female adult refugees/ asylum seekers is different. Study design Systematic review of current literature. Data Sources PubMed, Web of Science, Scopus and Google Scholar up until February 2019 Method A structured systematic search was conducted in the relevant databases. Papers were excluded, if they failed to meet the inclusion and exclusion criteria. Afterwards, a qualitative assessment was performed on the selected papers. Results 12 Studies were included for the final analysis. All papers were either case studies/report or cross sectional studies. The number of traumatic events experienced by refugees/asylum seekers, is the most frequently reported pre-migration causes for PTSD development. Whilst acculturative stress, is the most common post migration stressor. There were mixed reports, regarding the causes of PTSD between both genders of refugees/asylum seekers. Conclusion This reviews’ findings, have potential clinical application into helping clinicians, to risk stratify refugees/asylum seekers for PTSD development and thus aid in embarking on earlier intervention measures. However, more rigorous research similar to this one, is needed for it to be implemented into clinical practice.

Public key encryption methods are often used to create a digital signature, and where Bob has a public key and a private key. In order to prove his identity, he will encrypt something related to the message with his private key, and which can then be checked with his public key. The main current methods of public-key encryption include RSA and ECC (Elliptic Curve Cryptography), and which involve computationally difficult operations. But these operations have not been proven to be hard in an era of quantum computers. One well-known hard problem is the solving of quadratic equations with $m$ equations with $n$ variables. This is a known NP-hard problem, even in a world of quantum computers. These can be used as post-quantum signature schemes and which involve multivariate equations. In order to understand these methods, this paper outlines a simple example of implementing the oil and vinegar method, and where we have a number of unknown oil variables and a number of known vinegar variables, and where the vinegar variables help convert the hard problem into an easy one.

Biochirality is evident in the hierarchical relation of molecular and cellular physiology during organism development and aging. Chirality influences the higher levels of biological processes, such as perception, memory and cognition, through intermolecular interactions between DNA, proteins, and lipids. At the molecular level, an organism's aging is the accumulation of macro-molecules with the aberrant composition, chirality, and folding. Cellular aging is driven by the non-physiological phase transitions (PhTs) withing membrane-bound and membrane-less compartments. Genomic instability and protein aging, as the interconnected root-causes of cell and organism aging, share two essential feature – spontaneous nature and accumulation over a lifetime. Consequently, we will analyze the interaction between the enzymatic (Enz) and spontaneous (Sp) post-translational modifications (PTMs^Enz and PTMs ^Sp). Both forms of PTMs significantly contribute to the balance of L- and D-amino acids (L/D-AAs) in organisms, modulating the functions of nervous and immune systems. The most abundant form of PTM - enzymatic phosphorylation is bio-chemically associated with the spontaneous racemization (Rz^Sp). The crass talk of enzymatic phosphorylation and spontaneous racemization, as an essential determinant of protein aging and aggregation, associated with the aberrant autophagy, apoptosis, and cell signaling, is discussed in this review.

Symbolic pole/zero analysis is an important step when designing an analog operational amplifier. Generally, a simplified symbolic analysis of analog circuits suffers from NP-hardness, i.e., an exponential growth of the number of symbolic terms of the transfer function with the circuit size. In this study, we present a mathematical model combined with a heuristic-metaheuristic solution method for the symbolic pole/zero simplification in operational transconductance amplifiers (OTA). At first, the circuit is symbolically solved and an improved root splitting method is applied to extract symbolic poles/zeroes from the exact expanded transfer function. Then, a hybrid algorithm based on heuristic information and a metaheuristic technique using simulated annealing is performed for the simplification of the derived symbolic pole/zero expressions. The developed method has been tested on three analog OTAs. The obtained results show the effectiveness of the proposed method to achieve accurate simplified symbolic pole/zero expressions with the least complexity.

This paper proposes a parameter coordination optimization design of Power System Stabilizer (PSS) based on an improved Quasi-Affine Transformation Evolutionary (QUATRE) algorithm to suppress low-frequency oscillation and improve the dynamic stability of power system. To begin, the Simulated Annealing (SA) algorithm randomly updates the globally optimal solution of each QUATRE iteration and matches the inferior solution with a certain probability to escape the local extreme point. This new algorithm is first applied to power system. Second, Since damping ratio is one of the criteria to measure the dynamic stability of power system, this paper sets the objective function according to the principle of maximization of damping coefficient of electromechanical mode, and uses SA-QUATRE to search a group of global optimal PSS parameter combinations to improve the stability margin of the system as much as possible. Finally, the method's rationality and validity were validated by applying it to the simulation examples of IEEE 4-machine 2-area system with different operation states. The comparison with the traditional optimization algorithm shows that the proposed method has more advantages for multi-machine PSS parameter coordination optimization, and can restrain the low-frequency oscillation of power system more effectively and enhance the system stability.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

Optical motion capture systems are state-of-the-art in motion acquisition, however as any measurement systems they are not error free -- noise is their intrinsic feature. The works so far mostly employ simple noise model, expressing the uncertainty as a simple variance. In the work we prove the existence of several types of noise and demonstrate how to quantify them using Allan variance. For the automated readout of the noise coefficients we solve the multidimensional regression problem using sophisticated metaheuristics in exploration-exploitation scheme. Besides classic types of noise we identified the presence of the correlated noises and periodic distortion in our facility. We had also opportunity to observe the influence of camera failure to the overall performance.

This article presents a narrative review of neonatal and paediatric complications in post-dated pregnancy and covers scientific views on the aetiology, pathology, risk factors, symptoms and complications of post-dated pregnancy. A pregnancy extending beyond 42 weeks of gestation is termed as a post term pregnancy. There are multiple complications that can occur in the perinatal period, some of the most common ones are stillbirth, asphyxia, meconium aspiration syndrome, fetal distress syndrome, etc which are found to be greater in post-dated pregnancy and hence ultimately leads to increased mortality and morbidity of the new born. Studies have shown that post-term pregnancy also causes increased risk of developing behavioural and emotional problems in children of paediatric age group. It is surprising not much importance has been given to the maternal and neonatal consequences of post- term pregnancies. It is not well understood why some women experience post-dated pregnancies. It is found that factors such as hormones and genetic build up, are responsible for causing post-term pregnancy in an obese female. The treatment and management of a post-term pregnancy still poses a challenge to clinicians in determining the right choice and right time for a particular intervention so that both mother and fetus can be prevented from having complications.

Introduction: Outcome measures using telerehabilitation (TR) in the context of post-stroke rehabilitation is an area of emerging research. The current review assesses the literature related to TR for patients requiring post-stroke rehabilitation. The purpose of this study additionally is to survey the outcome measures used in TR studies and to define which parts of the International Organization of Functioning are measured in trials. Methods: TR studies were searched in Cochrane Central Register of Controlled Trials, PubMed, Embase, Scopus, Google Scholar, and Web of Science from 2016 to June 2023. Two reviewers individually assessed the full text. Disagreements about inclusion or exclusion were determined by consensus or by checking with a third reviewer. Results: A total of 24 studies were included in the current review. The results were synthesized and reported considering the implications of the results within clinical practice, areas of investigation, and strategic implementation. Conclusions: The current scoping review recognized a wide range of outcome measures used in TR studies and helped elucidate gaps in the current use of outcome measures in the literature. The scoping review also informs researchers and end users (i.e. clinicians and policymakers) regarding the most suitable outcome measures for TR.

The purpose of this study was to analyze the influence of Chitosan 0.2% in various final cleaning methods on the bond strength of fiberglass post (FP) to intrarradicular dentin. Ninety bovine incisors were sectioned to obtain root remnants measuring 18 mm in length. The roots were divided: G1: EDTA 17%; G2: EDTA 17% + PUI; G3: EDTA 17% + EA; G4: EDTA 17% + XPF; G5: Chitosan 2%; G6: Chitosan 2% + PUI; G7: Chitosan 2% + EA; G8: Chitosan 2% +XPF. After carrying out the cleaning methods, the posts were installed, and the root cleaved to to generate two disks from each root third. Bond strength values (MPa) obtained from the micro push-out test data were assessed by Kruskal-Wallis and Dwass-Steel-Critchlow-Fligner tests for multiple comparisons (α = 5%). Differences were observed in the cervical third between G1 and G8 (p=0.038), G4 and G8 (p=0.003), G6 and G8 (p=0.049), and Control and G8 (p=0.019). The final cleaning method influenced the adhesion strength of cemented FP to intrarradicular dentin. Chitosan 0.2% + XPF positively influenced adhesion strength, with the highest values in the cervical third.

Actively combating post-harvest food spoilage and waste can dramatically increase the efficiency of food utilization worldwide. In climacteric fruits, chemical treatments such as 1-MCP are an effective way of reducing post-harvest spoilage and waste by inhibiting the fruit’s ability to perceive ethylene. 1-MCP treatment is increasingly being used to explore the complex nature of ripening physiology at a fundamental level, however, differences in application and quantitation methods create difficulties in comparing conclusions across studies. Here we report an effective and reproducible method for 1-MCP application and quantitation for small-medium sized research applications. By use of surrogate alkene standards 1-butene and cis-2-butene, the highly volatile and elusive 1-MCP molecule can be identified and quantified by gas chromatography and subsequent standard curves may be developed. It is hoped that the methodology outlined here can help standardize consistent 1-MCP application for post-harvest research without excessive investment in specialized equipment.

Post-evaluation of ecological redevelopment is a good method for its achievements. The eco-engineering technologies and achievements of landscape water reconstructed from aquaculture ponds in Shanghai Chenshan Botanical Garden have been introduced in this study. The sediments and water quality were also sampled and tested for basic physicochemical parameters and heavy metal concentration. The ecological redevelopment of landscape water reconstructed from aquaculture ponds was evaluated using the Nemero comprehensive pollution index method. The results shown that nutrients including organic matter, organic nitrogen and their ratio of sediment were found to be in a state of moderate pollution, while their ecological risk of heavy metals was low. Although total nitrogen and total phosphorus of water quality was really higher than that of other indexes, the decline trends of ammonia nitrogen, total nitrogen and total phosphorus was obvious presented over time. In general, this is a good example that redevelopment of water ecosystems from aquaculture ponds using eco-engineering technologies.

Residential satisfaction with post-disaster housing is crucial for the success and sustainability of a resettlement project. However, little attention has been given to this aspect in the permanent houses developed after the 2015 Gorkha earthquake. To bridge this gap, the study examined factors affecting residential satisfaction among poor displaced households resettled in the Panipokhari Integrated Settlement of Nepal. Data were collected through a questionnaire survey, interviews, and field observation. Internal consistency and reliability were assessed using Cronbach's Alpha test, while satisfaction was measured by mean satisfaction scores. The relative importance index ranked the factors, and Spearman's rank correlation coefficient analyzed their relationship with overall residential satisfaction. The study identified several crucial fac-tors influencing residential satisfaction, including the design and layout of the house, space for modification, provision of a kitchen garden and cattle shed, thermal comfort, completeness of the house, provision of a hearth, and spaces for rituals and cultural events. These findings shed light on the resettlement decisions of affected populations and provide valuable insights for policymakers, implementers, and researchers aiming for successful and sustainable resettlement outcomes.

Background: Optimal hypofractionated schedule of post-prostatectomy radiotherapy remains to be established. We evaluated treatment outcomes and toxicity of the moderately hypofractionated post-prostatectomy radiotherapy in 16 daily fractions delivered with IMRT/VMAT. The treatment schedule selection was motivated by limited technology resources. Methods: One hundred consecutive M0 patients with post-prostatectomy radiotherapy were evaluated. Radiotherapy indication was adjuvant (ART) in 19%, early salvage (eSRT) in 46% and salvage (SRT) in 35%. The dose prescription for prostate bed PTV was 52.8 Gy in 16 fractions of 3.3 Gy. The Common Terminology Criteria v.4 for Adverse Events scale was used for toxicity grading. Results: The median follow-up was 61 months. Five-year biochemical recurrence-free survival (bRFS) was 78.6%, distant metastases-free survival was 95.7% and overall survival was 98.8%. Treatment indication was the only significant factor for 5-year bRFS in multivariate analysis which was 84.6% vs. 67.6% for ART or eSRT vs. SRT respectively (HR 0.15, 95% CI 0.05–0.47, p=0.001). Acute GI toxicity grade 2 was recorded in 24%, grade 3 in 2% and acute GU toxicity grade 2 in 10% and no grade 3. Cumulative rate of late GI toxicity grade ≥2 was observed in 9% and late GU toxicity grade ≥2 in 16%. Conclusion: Observed results confirmed efficacy and acceptable toxicity of post-prostatectomy hypofractionated radiotherapy in 16 daily fractions.

Current study was to estimation the post-harvest loss of avocado at the producer level using cross-sectional data obtained from 385 proportionately sampled respondents from Wolaita and Kembata Tembaro Zones, the SNNPR of Ethiopia. Descriptive and multiple regression analysis were used to the amount and determinant of post harvest loss of avocado fruits. Estimated total post harvest- loss of avocados was 24%; of which 5.7% unacceptable harvesting methods and 4.9% of improper storage practices. The respondent's sex, education, income, training, contact with extension agents, distance from the nearest road, and off-farm income were found to be negative determinants, whereas storage accessibility and avocado harvest techniques were found to be positive determinants of post-harvest loss of avocado fruits. Post-harvest management techniques for avocados need to be better understood and used by avocado growers if they are to minimize losses. Post-harvest losses contribute considerably to food insecurity and create a problem for the source of revenue for people and the economy of the country as well. Therefore, the use of a practical and effective post-harvest loss reduction technique could be a sustainable solution to increase food availability, eliminate hunger and improve farmers' livelihoods.

The universal chirality is the commonly accepted view of nature. Biological chirality is the distinct part of the more general phenomena. Following this view, all living organisms are characterized by the non-equilibrium state of their molecular constituents. From the thermodynamic perspective, the non-equilibrium state of biomolecular ensemble holds inevitable consequences being the substrate of spontaneous reactions directed to equilibrium (not associated with life) state. At the protein level, spontaneous biological reactions represent the natural part of proteins' post-translational modifications (PTMs). The essential contribution to the origin and maintenance of the non-equilibrium state belongs to prevalent bio-molecular chirality. Correspondently, spontaneous PTMs such as racemization and glycation, working against life-supporting prevalent chirality, are known as the significant determinants of protein misfolding, dysfunctions, and aggregation. Accumulation of aberrant protein during life-span allows consideration of time-dependent spontaneous racemization and glycation as protein aging. Spontaneous PTMs of proteins is occurring in the interaction with other forms of enzymatic and non-enzymatic PTMs. In this review, we are considering the contribution of spontaneous racemization and non-enzymatic glycosylation to protein aging.

Smoking during pregnancy remains one of the most significant risk factors for poor birth outcomes. The Loma Linda University Health Comprehensive Tobacco Treatment Program (CTTP) is the largest maternal tobacco cessation program in San Bernardino County – the largest county in the contiguous US. CTTP is an eight week, incentivized, behavioral intervention for tobacco cessation for pregnant smokers. As part of program evaluation, we used a retrospective cohort design to assess smoking abstinence and to identify predictors of relapse/smoking after enrollment. Among CTTP cohort enrollees (n=233) from 2012-2013 we found: 1) a 28.4% 8 week point prevalence abstinence (PPA), and at a median of 9 months of follow-up after the PPA, 81.6% continued to indicate tobacco cessation, and 2) a high rate of relapse or loss to follow-up (56%). Our modeling of relapse/smoking after enrollment indicated that this was higher in young mothers, non-Hispanic mothers (White, Black), first/third trimester mothers, and rural mothers. The evaluation identified efficacy of the behavioral model at 8 weeks, but that relapse/smoking was occurring in disparity populations. Formative research is needed to expand the programmatic outreach and enrollment of mothers wanting to quit smoking.

Postpartum depression (PPD), a condition that affects up to the 15% of mothers in high-income countries, reduces attention toward the needs of the child and it is among the first causes of infanticide. PPD is usually identified using self-report measures and therefore the diagnosis may not always be valid. Previous studies highlighted the presence of significant differences in the acoustical properties of the vocalizations of children of depressed and healthy mothers. In this study, cry episodes of infants of depressed and non-depressed mothers are analyzed to investigate the possibility that a machine learning model can identify PPD in mothers from the acoustical properties of infants' vocalizations. Acoustic features (F0, F1-4, Intensity) are first extracted from recordings of crying infants, then novel cloud-based artificial intelligence models are employed to identify maternal depression versus non depression from estimated features. Trained model shows that commonly adopted acoustical features can be successfully used to individuate Post-Partum Depressed mothers with very high accuracy (89.5%).

Background: Paracetamol may be use as antipyretic agent for the treatment of fever, as well as an analgesic in the treatment of mild to moderate pain on post vaccination in infants. The use of Paracetamol during fever may be or may not be recommended since it may alter natural human body immune response although it may reduce pain. Objectives: This study described the relevancy of Paracetamol use post infants vaccination based on data collection systematic review analyses. This study aims to describe the effectiveness of breastfeeding in reducing pain and Paracetamol in reducing fever and pain post infants vaccination. Data Sources and Study Selection: Electronic literature search by hand searching six (6) databases which include Ovid LWW Total Access Collection and Medline, CINAHL (Cumulative Index to Nursing and Alled Health Literature) Plus with Fulltext, Science Direct, Proquest Dissertations and Theses, Proquest Education Journal and Proquest Health and Medical Complete. Additionally, manual reference checks of all articles on Paracetamol and breastfeeding post infants vaccination published in English Language between 1978 and 2017. Two level of screening were used on 9614 citations which include screening of abstracts and titles followed by full text screening. Data Synthesis: Data synthesis were tabulated into study characteristics, quality and effects. Authors of trials were not contacted for further details or provision of original data if the published report contained insufficient information. The study findings, as reported by the authors, were included in this review. The data in this research cannot be pool due to not enough data regarding odd ratio or relative risk as well as confidence interval in each study. Results: Systematic review of breastfeeding included three (3) studies from 9614 of database searching. The reviews of all these three (3) studies found significant benefit from breastfed in pain score and duration of crying as well as behavioral changes. None study stated the unbeneficial of breastfeeding before, during and after immunization. Meanwhile, systematic review of Paracetamol effectiveness included four (4) studies from 1177 of database searching. The reviews of two (2) studies found significant benefit from prophylaxis Paracetamol in fever and only one (1) study found significant benefit from prophylaxis Paracetamol in fussiness. On the other hand, there was one (1) study found not signifiant benefit from prophylaxis Paracetamol in fever. Other than that, there were two (2) studies evaluate the safety of prophylactic Paracetamol which revealed different outcomes, in which study by Prymula et. al. in 2009 found that antibody responses to several antigens were reduced significantly, and the other study by Uhari et. al. in 1988 found that antibody titres to DTP bacteria of placebo and PCM not differ significantly. Thus, Paracetamol seems to be not relevant post infants vaccination and breastfeeding was found to be beneficial post infants vaccination. Conclusions: The relevancy of giving Paracetamol post all types of vaccination may be questionable since the safety issue of this intervention may be arised. Breastfeeding before, during and after immunization are recommended for pain reduction as it was proved effectively. Finally, in deciding Paracetamol to be of rational use following infants immunization, it may need for further research which include in depth quantitative and qualitative studies to identify specific problem and causes regarding this issue.

Experimental quantification of retention factors related to post-fire strength as well as post-fire ductility of intentionally selected stainless steel grades applied in construction is the objective of research presented here. These steel grades are characterized by a two-phase austenitic-ferritic microstructure of the duplex type. In this context two mutually corresponding chromium-nickel-molybdenum steel grades have been subjected to analysis, namely X2CrNiMoN22-5-3 steel belonging to the standard duplex group (DSS 22% Cr) and X2CrMnNiN21-5-1 steel belonging to the lean duplex group (LDSS). The similarities and differences in the mechanical properties exhibited by these steel grades after effective cooling, following more or less prolonged simulated fire action conforming to several development scenarios, have been identified and indicated. The resistance of given steel grade to permanent structural changes induced by the heating program proved to be the critical factor determining these properties and resulting in many cases in increased susceptibility to brittle fracture.

Introduction: Despite more than one year passed since the first cases of SARS-CoV-2 were reported, there is still no consensus on the definition and clinical management of post-acute-COVID-19. The condition has heterogeneously been named as Chronic COVID syndrome, Post COVID-19 Syndrome, post-acute sequela of SARS-CoV-2 (PASC), and the more familiar long COVID. Method: In order to capture all relevant published studies, we undertook a multi-step search with no language restriction. The following four-step search strategy was utilized: First, a preliminary (limited) search was conducted on January 20, 2021, in Google Scholar and PubMed to identify the appropriate keywords. Then, on January 30, 2021, we adopted a search strategy of electronic databases from Cochrane Library, PsycINFO, PubMed, Embase, Scopus, and Web of sciences, using those keywords. Then, after duplicate removal, we screened all titles, abstracts, and full texts. This resulted in 66 eligible studies. Subsequently, after a forward and backward search of their references and citations an additional 54 publications were found, resulting in a total of 120 publications that formed the basis of the present analysis. The titles, abstracts, and full-texts of non-English articles were translated using Google Translate for further evaluation. We conducted our scoping review based on the PRISMA-ScR Checklist.Results: We found only one randomized clinical trial in our search. Of the 67 original studies, 22 were cohort and 28 were cross-sectional studies totaling 74.6% of the original studies. Of the total of 120 publications, 59 (49.1%) focused on signs and symptoms, 28 (23.3%) were focused on management, and 13 (10.8%) focused on pathophysiology. Ten (9%) publications focused on imaging studies. Ninety-one percent of the original investigations came from high and upper-middle-income countries, highlighting the scarcity of reports originating from low-income and lower-middle-income countries.Conclusion: The predominant symptoms among those with the so-called “Long COVID” were: fatigue, breathlessness, arthralgia, sleep difficulties, and chest pain. Recent reports also point to the risk of long-term sequela with cutaneous, respiratory, cardiovascular, musculoskeletal, mental health, neurologic, and renal involvement in those who survive the acute phase of the illness. The ambiguity and controversies in its definition have impaired proper recognition and management of those requiring additional support following the resolution of the acute phase of this infection. This has resulted in long-standing distress for the patients and their families. Our findings highlight the need for a multidisciplinary approach, support, and rehabilitation for these patients in terms of long-term mental and physical health.

With the engineering system becoming more and more complex, the uncertainty factors have a more and more profound influence on the reliability and security of the engineering system. In recent years, Reliability-Based Design Optimization (RBDO) has been studied extensively in complex engineering system design. The research on reliability optimization design considering stochastic uncertainty has been comprehensive and widely used. However, the reliability optimization design considering mixed uncertainty has the disadvantages of large computation and imprecise convergence. This study proposes an RBDO method based on Particle Swarm Optimization (PSO) and Simulated Annealing (SA) to overcome this challenge. In the method, PSO is used to solve the most probable point, while SA has excellent global optimization capability to acquire the global optimal solution. Finally, three examples are given to illustrate the advantages of the proposed method.

Practical entanglement distillation is a critical component in quantum information theory. Entanglement distillation is often utilized for designing quantum computer networks and quantum repeaters. The practical entanglement distillation problem is formulated as a bilevel optimization problem. A fuzzy formulation is introduced to estimate the quantum state (density matrix) from pseudo-likelihood functions (i.e., quantum state tomography). A scale-independent relationship between fuzzy relations in terms of the pseudo-likelihood functions is obtained. The entanglement distillation optimization problem was solved using the combined coupled map lattice and dual annealing approach. Comparative analysis of the results is then conducted against a standard dual annealing algorithmic implementation.

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. Therefore, the effect of twinning and annealing, which can affect to the recrystallization were investigated in this study. An AZ31 alloy was hot rolled at 673K with a reduction ratio of 10 % and 50 %, and then annealed at 673K and 723K for 0.5, 1, 2, and 3H respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen’s hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673K, the decrease in dislocation density was delayed while, the internal friction showed a relatively low value.

This work presents significant results obtained by the application of global optimization techniques to the design of finite, normal form games with mixed strategies. To that end, the Fuzzy ASA global optimization method is applied to several design examples of strategic games, demonstrating its effectiveness in obtaining payoff functions whose corresponding games present a previously established Nash equilibrium. In other words, the game designer becomes able to choose a convenient Nash equilibrium for a generic finite state strategic game and the proposed method computes payoff functions that will realize the desired equilibrium, making it possible for the players to reach the favorable conditions represented by the chosen equilibrium. Considering that game theory is a very significant approach for modeling interactions between competing agents, and Nash equilibrium represents a powerful solution concept, portraying situations in which joint strategies are optimal in the sense that players cannot benefit from individually modifying their current strategies provided that other players do not change their strategies as well, it is natural to infer that the proposed method may be very useful for strategists in general. In summary, it is a genuine instance of artificial inference of payoff functions after a process of global machine learning, applied to their numerical components.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

The pandemic was an enormous experience all over the world. The type of living, working and study were changed irreversibly. Facing the opportunity to establish old frames of education in universities is impossible. The adoption of new ways of teaching and assessments reveal their convenience and in the same way their weak points. In response to that stage, on 14 December 2022, the EU parliament accepted the "Digital Decade Policy Programme 2030", for the establishment of a digital transformation community (EU 2022). Trakia University had an online assessment system, quizzes for self-training, and final exams, developed in 2008 on Moodle virtual learning environment. During the pandemic, online exams and lectures were conducted using platforms like BigBlueButton in Moodle or Google Meets. The article gives the results of online exams before, during, and after the pandemic. The outcome, without doubt, displays the lowering knowledge level or performance during the social isolation due to COVID-19, and after, and the reasons are discussed. During the second year of the pandemic was mentioned also a high dropout of students. Now the situation is returning to the previous levels, before the pandemic, but the quality of education is not yet reached. The article values the grades results of session exams and has the intention to clarify the influence of the pandemic period on the excellence of high institution education.

The study aimed to evaluate the after-effects of the COVID-19 pandemic on the sleep quality and patterns of women across different cultural settings within Iraq, spanning the period of 2022. A cross-sectional survey was administered to a diverse cohort of women from multiple provinces in Iraq. The survey measured various parameters, including sleep duration, onset latency, and disturbances. The post-pandemic period has seen a notable decline in sleep quality among the female population. Contributing factors include psychological stress, lifestyle changes due to the pandemic, and ongoing socio-economic challenges. The impact on sleep quality exhibited variation across different cultural groups, indicating a significant cultural influence on the pandemic's psychological aftermath. The study concludes that the post-pandemic phase has adversely affected the sleep health of women in Iraq, with cultural factors playing a critical role in these changes. There is a pressing need for culturally sensitive public health strategies to address sleep disturbances and mitigate their long-term effects on women's health. Public health initiatives should be tailored to address the specific cultural contexts within Iraq to improve sleep health among women. Further research is warranted to explore the long-term consequences of disturbed sleep patterns and the effectiveness of different intervention strategies.

Background Posttraumatic stress disorder (PTSD) is a complex condition that represents a significant burden in terms of individual disability and societal costs. Despite decades of research investigating treatment options, PTSD remains a major cause of quality-of-life impairment. We hypothesized that patients with PTSD might benefit from peripheral somatosensory stimulation (PSS) therapy. Methods Six adult patients with clinically diagnosed PTSD were enrolled to undergo daily PSS therapy over a 4-week period. Patients completed two surveys evaluating satisfaction with treatment and overall well-being (Survey 1) and severity of PTSD symptoms (Survey 2). Survey 1 was completed weekly during the course of the study. Survey 2 was based on the 9-question National Stressful Events Survey PTSD Short Scale (NSESSS) and was completed as a baseline prior to initiation of therapy and then at the conclusion of the trial. All data were analyzed by an independent statistician. Results Six male patients were enrolled in the study; all completed the trial. All patients demonstrated a decrease in symptoms within one week of initiation of therapy. This benefit was sustained and appeared to further improve over the course of the trial. For Survey 1, the overall median scores demonstrated a significant time-dependent improvement across measurement times (p < 0.001). For Survey 2, patients had statistically significant improvements from baseline regarding feelings of being emotionally upset and being overly alert. Results from a cumulative link mixed model demonstrated that treatment yielded a 38.2-fold higher likelihood of transitioning from a higher PTSD score at baseline to a lower (improved) score at week 4. No adverse events were described by the patients. Conclusions PSS stimulation appeared to improve symptoms in all six patients with PTSD symptoms in this trial. Patients had unanimous and clinically meaningful improvement in overall PTSD symptoms with treatment. By week 4, all patients responded that they enjoyed the treatment and would like to keep their device. We suggest that further investigation into the potential usefulness of PSS therapy in patients with PTSD is warranted.

Post-traumatic stress disorder (PTSD) is a debilitating mental health disorder that causes significant dysfunction in individuals. Currently, there are many approved Pharmacotherapy and Psychotherapy treatment options for PTSD, but unfortunately, half of the patients do not respond to traditional therapies. In this article, we reviewed clinical trials and research on 3,4-methylenedioxymethamphetamine (MDMA) assisted Psychotherapy in PTSD patients, its pharmacokinetics and current treatment guidelines for PTSD. Based on the results of the efficacy of MDMA assisted Psychotherapy from six phases II Randomized controlled trials. MDMA-assisted Psychotherapy for PTSD has received the “Breakthrough Therapy” designation from the FDA. MDMA can potentially reduce PTSD symptoms even in treatment-resistant cases by increasing certain neurohormones, i.e. dopamine, serotonin, norepinephrine and oxytocin. It also modulates activities in the brain regions involved in fear and anxiety. Future research is needed to show whether the advantages outweigh the disadvantages and whether its use can be integrated into available treatment options for PTSD.