Battery/Supercapacitor(SC) current tracking control is a key issue for hybrid energy storage system (HESS) in electric vehicles. An innovative passivity-based L2-gain adaptive control (PBL2AC) based on port-controlled Hamiltonian model with dissipativity (PCHD) for reference current tracking and bus voltage stability in HESS is presented. The developed PCHD model has considered both parameter variations and external disturbances. By using L2-gain disturbance attenuation, the PBL2AC ensures robust reference current tracking and stable bus voltage. Moreover, adaptive mechanism is adopted to estimate the electrical parameters. To validate the proposed control scheme for HESS, simulations and experiments were done and compared with traditional PID and sliding mode control under several typical driving cycles, and results show that the effectiveness of the proposed controller can be confirmed.

Today, maritime transport is responsible for moving approximately 80 percent of the volume of world trade, which has favored Colombia, which, due to its geographical position, has managed to become one of the most competitive and dynamic economies in the world. South America. For this reason, this investigation is carried out in a port of their country, with the aim of identifying and analyzing restrictions or critical points that may cause delays in the unloading of goods, these would also cause delays in the loading of vehicles. To do this, it began with a diagnosis of the current situation through interviews with the operational personnel of the port, then a simulated model was designed in the ARENA software, in which it was observed that the weighing activities are where the queues were formed, this will cause a delay in the download. As possible solutions, it is recommended to senior management that a proper verification of the operation of the weighing equipment be carried out in order to unload goods more quickly. In addition, a replacement weighing equipment must be purchased. With this change, it would be possible to reduce inefficiencies or cost overruns caused by download delays, which are reducing the fluidity of the goods and the competitiveness of the organization

In this work is represented conceptual model of robot-manipulator for capture and holding no-cooperation client spacecraft, which has Payload Adapter interface PAS 1666 S, PAS 1194 C, PAS 1666 MVS, PAS 1184 VS, when there are dynamic errors of linear and angular position of client spacecraft in the interval +/-5 deg. per minute and +/-0.1 meters per minute respectively.

The purpose of this article is to analyze, in a three-stage research, the relationships between environmental expenses, the improvements achieved in 5 environmental variables analyzed and efficiency, from an economic and operational perspective. The stages of this research are analyzing the sustainability reports to determine the level of information, analyzing the economic and operational efficiency, and analyzing the alignment with the environmental priorities of the Eco Ports-ESPO (European Sea Ports Organization). The results reveal that (1) the type of traffic does not condition environmental actions; (2) environmental performance (improvements) depends on environmental expenditures; (3) environmental spending and efficiency in port operations are correlated; and (4) environmental spending and port economic efficiency are correlated.

Abstract: Marine eutrophication is a pervasive and growing threat to global sustainability. Thereby nutrient discharges to the marine environment should be reduced to a minimum. When fertilizers are loaded to vessels in ports, a significant amount of nutrients are released into the sea, but so far these actions have received little attention. Here, we employed the Boosted Regression Trees modeling (BRT) to define relationships between fertilizer loading, loading area, rain intensity and nutrient discharge to the marine environment and then used the established relationships to predict daily nutrient discharge due to fertilizer loading. The studied subject was a port in the Gulf of Finland, where significant amount of both nitrogen and phosphorus are loaded to vessels. BRT models accounted for a significant proportion of the variability of nutrient discharge. As expected, the nutrient discharge increased with the amounts of fertilizers loaded and the intensity of rain. On the other hand, with increasing loading area the amounts of total nitrogen discharge increased, but phosphorus discharge decreased. The latter result may be due to different char-acteristics of the loading areas of different terminals. The model predicted that at the studied port the total nitrogen and phosphorus discharge into the marine environment due to fertilizer loading was 272,906 and 196 kg per year, respectively. Im-portantly, the developed model can be used to predict nutrient loads for different future scenarios to propose the best mitigation methods for nutrient discharges to the sea.

In this paper a microstrip Wilkinson power divider with a 90^° phase delay at one output port is proposed to obtain circular polarization to feed a dual port RFID antenna. The 90^° phase delay was obtained by embedding an extra quarter wavelength at one port of the Wilkinson power divider. The feeding circuit is then mounted on the ground plane of the microstrip antenna feeding the radiating patch directly through the ground plane and dielectric layer thus reducing any fringing effect and resulting a mechanically compact unit. The proposed feeding method offers better expectation of antenna performance with minimal attenuation and coupling losses. The design process generalizes geometric pa- rameters of the Wilkinson power divider for variable port distances. The paper considers both UK and US RFID center frequencies, 870 MHz and 915 MHz respectively. Numeri- cally computed values for geometric design parameters for both frequencies are tabled as future design tools for port distances varying from 18 mm up to 34 mm at 870 MHz and 17 mm up to 32 mm at 915 MHz. Simulation results indicate a return loss (S11) of -20 dB and -26 dB at 870 MHz and 915 MHz operational frequencies respectively at 270^° angled quarter wavelength.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

Port cities’ sustainable development can start from innovation in maritime culture to build new urban visions based on the goals of Agenda 2030 and oriented towards local and international cooperation. In the international debate innovative strategies on cultural heritage enhancement contaminate the research and production contexts of ports. In addition, numerous cities have implemented creative and cultural responses to climate change and environmental sustainability. Creativity and cultural heritage enhancement can guide the definition of new trajectories of sustainable urban development, particularly in port-city interaction areas. In Europe, port-city interaction areas have been transformed into laboratories of cultural and creative experimentation for the sustainable management of cultural heritage and the urban quality of public spaces. In this perspective, the paper, starting from the studies developed on the main measurement frameworks of creative cities and sustainable development policies, aims to investigate the possibility of developing a "Port-cities Creative Heritage Enhancement" approach to assess and plan possible cultural and creative transformations of historical-architectural buildings, industrial archaeologies and symbolic urban spaces in the port-city interaction areas of Naples.

This research investigates Haifa ports emissions’ contribution to the existing daily emission inventory level in the area. This research based on developed full bottom-up model framework that looks at the single vessel daily voyage through its port call stages. The main data sources for vessels movements used in this research are the Israel Navy`s movements log and Israel Administration of Shipping and Ports’ (ASP) operational vessel movements and cargo log. The Fuel Consumption (FC) data and Sulfur Content (SC) levels are based on an official Israel ASP survey data. Observation years in this research are 2010 - 2018 with focus on the Ocean-Going Vessels (OGV) type only. The results show that the vessel fleet calling at Israel ports is mainly vessels that have a lower engine Tier grade (i.e., Tier 0 and 1) which is considered a heavy contributor to Nitrogen Oxides (NOx) pollutant. The study recommends on an additional cost charged (selective tariff) to reflect the external social cost linked to the single vessel air pollution combined with supportive technological infrastructure and economic incentive tools (e.g. electric subsidy) to attract or influence vessel owners to assign vessels equipped with new engine Tier grades for calls at Israeli ports.

Background DaVinci Single-Port (SP) robotic surgery offers several benefits compared to traditional multiport laparoscopic or robotic surgeries. One of the main advantages is that it allows for a minimally invasive approach, resulting in a single, smaller incision and reduced trauma to the patient’s body leading to less postoperative pain, faster recovery, and reduced risk of complications. The cosmesis of a single port with minimal visible scarring is also an attractive aspect to the patients; however, many surgeons use an additional port for energy device, stapler use, and drain insertion. Pure single port surgery with one incision is still rare. Here we share our experience of first 10 cases using SP robotic platform in colorectal surgery. Methods From May 2023 to December 2023, colorectal patients who underwent SP-robotic surgery were analyzed. Placement of the incision was umbilicus for 8 patients, and right lower quadrant for 2 patients through which ileostomy maturation was performed. Data including perioperative parameters and postoperative outcomes were analyzed with a median follow-up of 4.6months (range 0.6-7.4months). Results A total number of 10 colorectal patients underwent DaVinci Single-Port robotic colorectal surgery at our institution during this period. Demographics of the patients showed 4 males (40%) and 6 females (60%) with a median age of 63.5years (range 50-75years). Median body mass index (BMI) was 22.89kg/m2 (range 19.92-26.84kg/m2), and 9 patients were diagnosed with colorectal cancer and 1 patient was diagnosed with rectal gastrointestinal tumor. One patient underwent anterior resection and cholecystectomy simultaneously. Mean operation time was 222min (range 142-316min), and mean wound size was 3.25cm (range 2.5-4.5cm). Nine patients underwent surgery with single incision through which single port trocar was inserted, and one patient had one additional port for drain insertion. Mean hospital stay was 6 days (range 4-8 days) with 1 postoperative complication of bleeding requiring transfusion, but there was no re-admission within 30 days. Conclusion Overall, our experience with single-port robotic colorectal surgery has been promising. With only one patient with additional port for drain insertion, all nine patients underwent SP-robotic surgery with single incision for colon as well as rectal surgeries. Compared to an average postoperative length of stay of 6.5-8 days in laparoscopic colorectal surgeries reported in literature, SP-robotic surgery showed faster recovery of 6 days highlighting its benefits in patient recovery and satisfaction.

To realize sustainable capture fisheries management, Nizam Zachman as an ocean fishing port in practice has taken action to regulate fishing vessels and large pelagic purse seine fishing gear which is a form of control on the application of fishing vessel seaworthiness in an effort to ensure compliance with provisions on safety aspects and the seaworthiness of fishing activities. This study aims to examine and determine the priority strategy of Nizam Zachman ocean fishing port in implementing the seaworthiness of large pelagic purse seine vessels. The analytical method used is descriptive statistics using SWOT and AHP analysis. The results showed that the SWOT analysis based on internal and external factors in the IFAS and EFAS matrices obtained factor values of 0.36 and -0.1 which were located in quadrant IV or the S-T strategy, which mean by strengthening the role of Nizam Zachman ocean fishing port in complying with rules for purse seine owners large pelagic with good supervision in supporting the sustainability of fishery resources. The results of the AHP analysis of prioritising the four implementation aspects of the fishing vessel seaworthiness policy are on the communication aspect (0.346) by means of holding regular outreach; the disposition aspect (0.242) by systematically assessing seaworthiness and the need for evaluation; the resource aspect (0.234) by increasing the number and capacity of fishing vessel seaworthiness inspectors, and on the bureaucratic aspect (0.177), by applying the rules of supervision with prevention through assistance to large pelagic purse seine owners.

The capacity to externally control transcranial magnetic stimulation (TMS) devices is becoming increasingly important in brain stimulation research. Here we introduce MAGIC (MAGnetic stimulator Interface Controller), an open-source MATLAB toolbox for controlling Magstim and MagVenture stimulators. MAGIC includes a series of MATLAB functions which allow the user to arm/disarm the stimulator, send triggers, change stimulator settings such as amplitude, interpulse intervals, and frequency, and receive stimulator setting information via a serial port connection between a computer and the stimulator. By providing external control capability, MAGIC enables greater flexibility in designing research protocols which require trial-by-trial changes of device settings to realize a priori trial randomization or interactive ad hoc adjustment of parameters during an ongoing experiment. MAGIC thus helps to prevent experimental confounds related to the block-wise variation of parameters and facilitates the integration of TMS with cognitive/sensory tasks, and the development of more adaptive brain state-dependent brain stimulation protocols.

The city-port involves a decisive reality for the economic development of the territories and nations, capable of significantly influencing the conditions of well-being and quality of life, and of making the Circular City Model operational, preserving and enhancing seas and marine resources in a sustainable way, through the construction of appropriate production and consumption models, with attention to relations with the urban and territorial system. The Circular Economy paradigm identifies the ideal context in the city-port to rethink traditional development models and make ports driver areas for the regeneration of the city and metropolitan territories, in compliance with the EU Directive 2014/89 which considers maritime spatial planning as a tool for public authorities and stakeholders to achieve an integrated approach, promoting the development of maritime and coastal economies and the sustainable use of resources. The paper, starting from these assumptions, presents an adaptive decision-making process for the strategies development of the Naples (Italy) commercial port, aimed at re-establishing a sustainable city-port relationship and making operative Circular Economy principles.

To verify the authors’ mathematical model for water jet cooling of steel sheet, the previously performed experimental studies of temperature of the test plate in the roller quenching machine (RQM) were used. The calculated data of steel temperature evolution along the RQM length were compared with the readings of thermocouples inserted in the center of the test plate and at its surfaces. The core of the model is the dependence of the temperatures of film, transition and nucleate boiling regimes on the thickness of the oxide scale layer on the cooled surface. It was found that the model correctly takes into account the oxide scale on the sheet surface, flow rates and combinations of the RQM banks used, water temperature and other factors. For all experiments the calculated metal temperature corresponds well to the measured one. In the experiments with interrupted cooling, the calculated temperature plots repeat the characteristic changes in the experimental curves. The main uncertainty in the modeling of cooling in a wide temperature range can be contributed by the random nature of changes in the oxide scale thickness during water cooling. In this regard, the estimated thickness of the oxide scale layer should be considered as the main parameter for adapting the sheet temperature control process. The obtained data confirm the possibility of effective application of the model in the ACS of industrial TMCP (Thermo-Mechanical Controlled Process) systems.

The performance consistency of an RF MEMS switch matrix is a crucial metric, which directly impacts its operational lifespan. An improved crossbar-based RF MEMS switch matrix topology, the SR-Crossbar, was investigated in this article. An optimized port configuration scheme was proposed for the RF MEMS switch matrix. Both the utilization probability of individual switch nodes and path lengths in the switch matrix achieve best consistency simultaneously under the proposed port configuration scheme. One significant advantage of this scheme lies in that it only adjusts positions of input and output ports, with topology and individual switch nodes kept unchanged. This grants it a high level of generality and feasibility, and also introduces an additional degree of freedom for optimizations. The article also constructed a universal utilization probability function of single nodes, and formulated an optimization objective function for the SR-Crossbar RF MEMS switch matrix, which provides a convenient approach to directly solving the optimized port configuration scheme for practical applications.

The International Maritime Organization (IMO) has recently revised its strategy for shipping de-carbonization, deepening the ambition to reduce annual greenhouse gas emissions until 2050. The accomplishment of this strategy requires the large-scale deployment of alternative maritime fuels, whose diversity and technical characteristics impose transition challenges. While several studies address the production of these fuels, a notable gap lies in the analysis of the required adaptations in vessels and ports for their usage. This study aims to fill this gap through a comprehensive re-view of material compatibility, storage in ports/vessels, and bunkering technology. Firstly, we an-alyze key aspects of port/vessel adaptation: physical and chemical properties; energy conversion for propulsion; fuel feeding and storage; bunkering procedures. Then, we perform a maturity as-sessment, placing each studied fuel on the technological readiness scale, revealing the most prom-ising options regarding infrastructure adaptability. Finally, we develop a case study for Brazil, whose economy is grounded on maritime exports. Findings indicate that multi-product ports may have potential to serve as multi-fuel hubs, while the remaining ports are inclined to specific fuels. In terms of vessel categories, we find that oil tankers, chemical ships and gas carriers are the most ready for conversion in the short-term

Full-scale/model test comparison studies to validate the traditional ABL wind tunnel simulation technique are reviewed. According to the literature review, notable discrepancies between full-scale measurement results and model test results were observed by most performed comparison studies, but the causes of the observed discrepancies were not revealed in a scientific way by those studies. In this regard, a new research scheme for future full-scale/model test comparison studies is proposed in this article, which utilizes the multiple-fan actively controlled wind tunnel simulation technique. With the new research scheme, future full-scale/model test comparison studies are expected to reasonably disclose the main problems with the traditional ABL wind tunnel simulation technique, and the technique can be improved correspondingly.

Djibouti shares an exceptional geostrategic position by being close to one of the busiest maritime routes, which makes it possible to have a crucial position for the movement of international trade transported by sea. This study analyses the influence of port development on Djibouti’s economic growth in the case of Doraleh Container Terminal and identifies other significant variable factors. In this paper, we analyze the existence of an influence port development on economic growth and other variables, by applying the perspective of the multiple regression model in the analysis using Eviews software. the selected datasets in the analysis cover the period from 2010 to 2020. The result show that port development has a direct and strongly positive influence on the economic growth of Djibouti. In addition, this study also reveals that imports and exports trade is a mediating variable with a significant influence on economic growth in Djibouti. Furthermore, foreign direct investment has not directly and positive influences on Djibouti's economic growth. Therefore, we recommend that the Government of Djibouti attract and promote the benefits of foreign direct investment to enhance the development of various economic sectors and achieve significant economic growth in the coming years.

In recent years, with the increase in maritime trade, the necessity of increasing the capacities of the ports has emerged. However, while it is planned to increase the capacities of the ports, it is important that the port continues to operate at the same time. In this respect, the old port structures should not be damaged during the capacity increase. In this study, the strengthening of a port in Guinea is discussed as a case study. In the study, the existing quay wall was evaluated, and geotechnical and structural alternatives of the new structure to be built for capacity increase were evaluated. A combined system was designed as a pile foundation and a reinforced foundation with plastic piles so as not to damage the existing quay wall. The pile capacities obtained as a result of the analyses were verified by loading tests.

Merchant marine fleet is under inspections by several parties to ensure maritime regulation compliance. One of the major effects on implementation of regulations by International Maritime Organization (IMO) is indeed Port State Control. This article aims to analyze Paris Memoranda of Understanding (MOU) all detention remarks from 2013 to 2019 for EU15 countries (except Luxemburg and Austria) through an approach based on Analytical Hierarchy Process and demonstrate the results on Geographic Information System (GIS) to guide marine industry on detainable Port State Control remarks and country risk profile. While Analytical Hierarchy Process Approach has been used to indicate the ranking of basic maritime regulations from the perspective of the port state control , GIS help us to demonstrate the regional dispersion amongst EU15. The data of the detained vessel taken from the public website of Paris MOU and each report considered as a professional judgement that causes detention. It has been shown that almost all countries top priorities for regulation are Safety of Life at Sea (SOLAS) and Fire Safety Systems (FSS). Consequently, the results of the study can assist Port State Officers, ship crew, ship owners and managers presenting the facts of their inspection and able to improve themselves. The spatial analysis also expected to guide ship owners and managers to focus their vessel’s deficiencies to prevent sub-standardization.

In order to ensure the sustainability of the shipping industry and marine ecosystem of Montenegro, it is necessary that Montenegro becomes a full member of the Paris Memorandum of Understanding (Paris MoU) on Port State Control. The reasons for doing so are numerous: the full adoption of standards stipulated by the Memorandum in relation to ship control; continuous keeping the pace with and development of new standards in compliance with turbulent changes in the maritime industry and operation (including the increasing scope of maritime transport); decrease in the number of detained ships which meet the requirements stipulated in international conventions and elimination of substandard ships in perspective; prevention of environmental pollution, sea and port incidents. This justified endeavour is supported by the fact that Montenegro is one out of two countries in Europe that are not the full members of the Paris MoU. Additionally, in this context it is necessary to emphasise the fact that the marine ecosystem of Montenegro makes an integral part of the world ocean. Accordingly, the improvement of the quality of national legislation which is compliant with international requirements is an imperative which has positive implications on the regional and global sustainability.

The field of controlled polymerization is growing and evolving at unprecedented rates, facilitating polymer scientists to engineer the structure and property of polymer materials for a variety of applications. However, the lack of degradability, particularly in vinyl polymers, is a general concern for not only environmental sustainability but also biomedical applications. In recent years, there has been a significant effort to develop reversible polymerization approaches in those well-established controlled polymerization systems. Reversible polymerization typically involves two steps including (i) forward polymerization which converts small monomers into macromolecules, and (ii) depolymerization capable of regenerating original monomers. Furthermore, recycled monomers can be repolymerized into new polymers. In this perspective, we highlight recent developments of reversible polymerization in those controlled polymerization systems and offer insight into the promise and utility of reversible polymerization systems. More importantly, the current challenges and future directions to solve those problems are discussed. We hope this perspective can serve as an “initiator” to promote continuing innovations in this fairly new area.

Italy has been defined as the "logistics platform" of the Mediterranean Sea. The Italian port system, with 11,6 million TEUs handled and 61,4 million passengers by 2022 (Assoporti data Jan‐Dec 2022) [1] is the key to guarantee this condition through adequate levels of reliability, safety and sustainability. This contribution addresses port logistics and shipping, focusing on primary issues related to the energy sector with a specific focus on what can be observed in the Italian context. Specifically, decarbonization of the maritime sector and related infrastructural problems (e.g. Cold Ironing or alternative fuels, where the uncertainty about resources availability and related cost do not allow for an easy strategic planning by both the shipowner and the port authority), as well as policies such the Emission Trading System (ETS) will be analyzed. All these issues, if addressed with a critical review, could represent the driving force of the national port sector for its growth and its competitiveness at a global scale.

Treatment with tumor-selective photosensitive substances, such as photodynamic therapy and photoimmunotherapy, has been reported to enable the visualization of tumor drug accumulation in real time and identify the required light irradiation dose by fluorescence imaging. However, fluorescence observation is difficult during treatments performed under gastrointestinal endoscopy because of the challenges associated with including the fluorescence filter in the camera part. To address this issue, this study developed a device that integrates a narrow camera and a laser diffuser to enable fluorescence imaging through a forceps port. This device was employed to demonstrate that a laser diffuser with an NIR fluorescence imaging sensor could be delivered through a 3.2-mm-diameter port. In addition, fluorescence images of Cetuximab-IR700 were successfully observed in two mice, and the fluorescence intensity confirmed that the fluorescence decayed within 330 s. This device is expected to have practical application as a tool to identify the optimal irradiation dose for tumor-selective photosensitive substances under endoscopy.

One of the most important problems of geotechnical engineering is the design of pile foundations. Piles are generally designed for vertical and horizontal static loads. However, it is important to design piles against dynamic loads in regions with high seismicity. This study verified a centrifuge experiment obtained from the literature with a finite element program. With the kinematic interaction analyses made for this purpose, the effect of parameters such as layered soil, groundwater, pile stiffness, and earthquake acceleration were investigated numerically. According to the results obtained, it was understood that the earthquake magnitude is the most important parameter in kinematic interaction analyses. In addition, in layered soil conditions, the fact that 75% of the pile length is in the weak soil creates the most unfavorable situation. It has been observed that pile stiffness and groundwater level also have certain effects on the kinematic interaction.

Port state control inspections implemented under the Paris Memorandum of Understanding (MoU) have become known as one of the best instruments for maritime administrations in European Union (EU) Member States to ensure that the ships docked in their ports comply with all maritime safety requirements. This paper focuses on the analysis of all inspections made between 2013 and 2018 in the top ten EU ports incorporated in the Paris MoU (17,880 inspections). The methodology consists of a multivariate statistical information system (STATIS) analysis using the inspected ship’s characteristics as explanatory variables. The variables used describe both the inspected ships (classification society, flag, age and gross tonnage) and the inspection (type of inspection and number of deficiencies), yielding a dataset with more than 600,000 elements in the data matrix. The most important results are that the classifications obtained match the performance lists published annually by the Paris MoU and the classification societies. Therefore, the approach is a potentially valid classification method and would then be useful to maritime authorities as an additional indicator of a ship’s risk profile to decide inspection priorities and as a tool to measure the evolution in the risk profile of flag over time.

Various risks and uncertainties are strengthening the downside of the global economy. This paper aims to estimate the impact of US-China conflict and the WTO Appellate Body's shutdown on global logistics demand and to show the seriousness of the situation. Existing literature studies on protectionism or US-China trade conflict, with a focus on the effects of specific issues or impact on bilateral relations. No research has considered the adverse effects of the WTO Appellate Body's shutdown. This paper considers both US-China conflict and the installation of new NTBs in other countries due to weakened WTO function, and tries to suggest that the combination of tariffs and NTBs can severely reduce international trade and the demand for maritime logistics services, making this paper differs from previous studies. This paper suggests that a catastrophe could occur in global maritime logistics, based on quantitative estimates for the impact of global protectionism. Finally, underlining that the international trade order should not seriously be damaged, this paper proposes that countries around the world should seriously discuss this issue at the 12th WTO Trade Ministers' Meeting in Kazakhstan June 2020.

A developed six-port reflectometry (SPR) system was integrated to measure the relative permittivity of tumor and normal breast tissue for medical diagnostic purpose. In order to obtain an accurate and precise measurement, the calibration process was done to the SPR using the well-known three-standard technique. Next, the studied dielectric probe was connected to the calibrated measurement-port of the SPR. The open end of the probe aperture was dibbed into the normal and tumor synthetic breast tissue samples to measure the synthetic breast tissues dielectric constant, ɛrʹ, and loss factor, ɛrʺ in the frequency range of 1.5 GHz to 3.3 GHz. Finally, the comparative studies were conducted between commercial VNA with Keysight 85070E dielectric probe and the studied SPR-probe system based on the measured magnitude of the reflection coefficient, phase shift, dielectric constant, and loss factor of the synthetic breast samples. The maximum absolute errors of the measured reflection coefficient magnitude, phase shift, dielectric constant, and loss factor were found to be 0.01, 1.07°, 1.12, and 0.75, respectively. It was ascertained that the predicted dielectric constant, ɛrʹ, is able to differentiate between normal, (ɛrʹ < 50) and tumor, (ɛrʹ > 50) breast tissues.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

Background: Immersive and non-immersive VR technology has been increasingly employed in training. This has encouraged physicians working in skill development to try using it to improve the learning, emotional recognition, and social skills of various disorders. This study aimed to explore the controlled trials employing VR in autism, ADHD, and dyslexia. Methodology:A literature review has been conducted, on PubMed, Scopus, and Web of Science. Any controlled trial in the pediatric age group, involving the comparison of VR training with other types of therapies in autism, ADHD, and dyslexia was included. Results:Only four controlled trials were identified, comprising a total of 208 patients, with ages ranging from 6-16 years. Out of these studies, two involved patients with autism, one with ADHD, and one with dyslexia. VR was successful in improving emotional recognition but not social interaction in autism. All trials did not mention thoroughly possible complications of prolonged use of VR. Conclusion: Despite being a promising technology, there is still a long road to prove the validity of using VR in skills development. Few controlled trials have been tailored to explore VR advantages over conventional training and therapies, most of them have a limited sample size, a short training course, and no mention of possible setbacks, such as ocular effects and social isolation.

This work deals with the synthesis of bare and curcumin (CUR)-loaded chitosan (CS)-based macroparticles by ionic gelation using sodium hydroxide (NaOH) or sodium tripolyphosphate (TPP) as cross-linking agents. The resulting spherical-shaped macroparticles were studied using various characterization techniques, Scanning Electron Microscopy (SEM), Fourier Transformed Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). The release of CUR from the CS-based particles with respect to time was analyzed, and the encapsulation efficiency and degree of swelling were studied. All formulations showed excellent CUR trapping efficiency, exceeding 90%. In particular, the TPP-crosslinked macrobeads released 34 wt% of the charged CUR within minutes, while the remaining 66 wt% was released slowly due to the biodegradation of CS. The results indicate that the correct choice of gelling agent and its concentration leads to spherical particles capable of encapsulating CUR and releasing it in a wide range of kinetics depending on the specific application.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

Background: Overweight and obese adults seek effective exercise interventions to reduce accumulated fat, but the effectiveness of these interventions vary across studies. The purpose of this meta-analysis was to investigate the effectiveness of exercise interventions in overweight and obese adults based on measurement of accumulated fat distributions. (2) Methods: Databases were used to select eligible studies for this meta-analysis. Randomized controlled trials with a control and experimental group were included. Degrees of effectiveness of exercise interventions were computed to assess the benefits on reducing weight and subcutaneous, visceral, and ectopic fat accumulation. (3) Results: A total of twenty-one studies were included in this meta-analysis. Participation in exercise interventions showed beneficial effects in reducing weight and subcutaneous and visceral fat. The effectiveness of exercise interventions on ectopic fat accumulation could not be assessed due to the limited number of studies measuring ectopic fat. Additionally, effectiveness of exercise interventions that depended on measurements of accumulated fat varied. The average exercise intervention for overweight and obese individuals was moderate to vigorous intensity, 4 times per week, 50 minutes per session, and 22 weeks duration. (4) Conclusions: Participating in exercise interventions has favorable effects on reducing weight and accumulation of subcutaneous and visceral fat.

This paper proposes a re-conceptualization of the port supply chain as a smart service system, according to the theory of the Service science. Starting from a short literature review about the port supply chain approach and the Service science, a new comprehensive framework is provided to better understand the seaport dynamics and the creation of competitive port supply chains. The methodology used is the case study approach. The authors examined the port of Salerno (Italy), and re-conceptualized it as a smart port service systems. Both theoretical and practical implications are provided to enrich the literature about the port supply chain and to support the port operators.

Maritime ports represent an important ecosystem for pollutant emissions and, taking into account the ongoing energy transition, need to adopt new solutions to mitigate current emission levels. These emissions are partially avoidable if ships and vessels docked at the port use electric energy to feed their internal power needs instead of using their internal combustion engines. In Europe, there is an ongoing discussion on including such emissions in the European Emissions Trading System which will represent added costs for maritime operators. Onshore Power Supply systems can contribute to the ongoing energy transition by allowing the use of electric power to feed docked ships. As a first step to contribute to the development of Onshore Power Supply solutions, it is necessary to evaluate the added power needs that these systems would represent for the port. This paper presents a methodology that allows port operators to verify, straightforwardly and transparently, their power needs for Onshore Power Supply applications. The methodology is based on the historical data of docked ships at the port or quay level and provides an energy analysis of each type of vessel to determine the power to be installed at the port so that it is possible to supply energy to different types of ships and vessels simultaneously. Additionally, the implemented methodology provides economic and technical decision support factors by comparing the fuel costs with electric power costs, assessing the potential for this transition to Onshore Power Supply. The methodology is validated using a real case study for the port of Lisbon and obtained results demonstrate the potential for the installation of Onshore Power Supply in medium to large-dimension maritime ports.

Offshore electricity production, mainly by wind turbines, and eventually floating PV in the future, will contribute to increase renewable energy production, as well as their dispatchability. The need for that energy evacuation and the implementation of the hydrogen economy are challenges that arise the evaluation of such energy facilities for the direct production of hydrogen. The analysis of the alternatives for the evacuation of offshore renewable electricity for the production of hydrogen is presented. The analysis includes discussion about the current state of the art of hydrogen pipelines and subsea cables, as well as the storage and bunkering system that is needed on shore. The main options for energy evacuation will be via an electric subsea cable to produce hydrogen onshore, or by pipeline, depending on the capacity of the offshore plant. For low capacity, an electric subsea cable is the best option. For high capacity renewable offshore plants, pipelines start to be competitive for distances above aprox. 450 miles.

Background: Clean cookstove interventions can theoretically reduce exposure to household air pollution and benefit health, but this requires near-exclusive use of the stoves, with simultaneous disuse of traditional stoves. Previous cookstove trials have reported low adoption of new stoves and/or extensive continued traditional stove use. Methods: The Household Air Pollution Intervention Network (HAPIN) trial randomized 3195 pregnant women in Guatemala, India, Peru, and Rwanda either to a liquefied petroleum gas (LPG) stove and fuel intervention (n = 1590) or to control (n = 1605). The intervention consisted of an LPG stove and two initial cylinders of LPG, free fuel refills delivered to the home, and regular behavioral messaging. We assessed intervention fidelity (delivery of the intervention as intended) and adherence (intervention use) through the end of gestation, as relevant to the first primary health outcome of the trial: infant birth weight. Fidelity and adherence were evaluated using stove and fuel delivery records, questionnaires, visual observations, and temperature-logging stove use monitors (SUMs). Results: 1585 women received the intervention, at a median (interquartile range) of 8.0 (5.0–15.0) days post-randomization and gestational age of 17.9 (15.4–20.6) weeks. Over 96% reported cooking exclusively with LPG at two follow-up visits during pregnancy. Less than 4% reported ever running out of LPG. Complete abandonment of traditional stove cooking was observed in over 67% of intervention households. 31.4% removed their traditional stoves upon receipt of the intervention, and among those who retained traditional stoves, the majority did not use them: traditional stove use was detected via SUMs on a median (interquartile range) of 0.0% (0.0%, 1.6%) of follow-up days (median follow-up = 134 days). Conclusions: Fidelity of the HAPIN intervention, as measured by stove installation, timely ongoing fuel deliveries, and behavioral reinforcement as needed, was high. Exclusive use of the intervention during pregnancy was also high.

The prevalence of obesity or metabolic syndrome is increasing worldwide (“Globally metabodemic”). Approximately 25% of adult general population is suffering from nonalcoholic fatty liver disease (NAFLD) which has become serious health problem. Hepatic fibrosis is the most significant determinant of all cause and liver -related mortality in NAFLD. Noninvasive test (NIT) should be urgently required to evaluate hepatic fibrosis in NAFLD. Fibrosis-4 (FIB-4) index is the 1st triaging tool for excluding advanced fibrosis because of its accuracy, simplicity, and cheapness especially for general physicians or endocrinologists, although FIB-4 index has several drawbacks. Accumulating evidence has suggested that vibration controlled transient elastography (VCTE) and the enhanced liver fibrosis (ELF) test may become useful as the 2nd step after triaging by FIB-4 index. The leading cause of mortality in NAFLD is cardiovascular disease (CVD), extrahepatic malignancy, and liver-related diseases. NAFLD often complicates chronic kidney disease (CKD), resulting in increased simultaneous liver kidney transplantation (SLKT). FIB-4 index could be a predictor of not only liver-related mortality and incident hepatocullar carcinoma (HCC) but also prevalent and incident CKD, CVD, and extrahepatic malignancy. Although NITs as milestones for evaluating treatment efficacy have never been established, FIB- 4 index is expected to reflect histological hepatic fibrosis after treatment in several longitudinal studies. We here review the role of FIB-4 index as 1st step NIT in management of NAFLD.

Development of early math skills is linked to future success in mathematics and other academics. Educational videogames have been shown to promote academic achievement; however, few rigorous studies have evaluated the use of educational videogames in supporting math development, especially in early primary education. In the current study, an open-label randomized controlled trial was conducted involving 134 first grade students to determine, using standardized assessments, the impact of the educational mathematics tablet-based videogame, Knowledge Battle, on math scores and self-competency. Overall, Knowledge Battle did improve math skills in participants who played the game. Among those with lower pre-game math skills, the Knowledge Battle group’s mean math score increased more than the control group’s mean math score (9.7 vs. 6.0; p=0.02). There was no association between perceived sense of self-competency and total math score (p=0.8141). However, players who had a higher sense of self-competency were more likely to enjoy playing the game. In conclusion, our findings suggest that Knowledge Battle was an acceptable and enjoyable educational mathematical videogame for first grade students, and may be most impactful for those with low math skills.

Healthy diet interventions have been shown to improve depressive symptoms, but there is a need for randomized controlled trials (RCTs) that are double-blind and investigate biological mechanisms. The primary objectives of this randomized controlled pilot trial were to test the palatability of the meals and acceptability of the intervention in preparation for a future 8-week RCT which will investigate whether a healthy Nordic diet improves depressive symptoms in individuals with major depressive disorder, and associated biological mechanisms. Depressed (n=10) and non-depressed (n=6) women and men were randomized to receive either a healthy Nordic diet (ND) or a control diet (CD) for 8 days. Participants were blinded to diet allocation and study hypotheses. Health questionnaires were completed before and after the intervention, and, throughout the study, questionnaires assessed ratings of liking and sensory properties of the meals, adherence, and open-ended feedback. In the ND group, 75% of participants consumed no non-study foods, compared to 50% of CD participants. The meals of both diets, on average, received good ratings for liking and sensory properties, though the ND ratings were somewhat higher. Overall, results were positive and informative, indicating that the planned RCT will be feasible and well-accepted, with some proposed modifications.

In many ports, the ship's speed is limited for the safety of navigation. At the same time, ship captains and port pilots choose the speed of the ship, but not higher than the permitted speed of the ship in the port, therefore the speed of the ship also depends on the experience of the ship captains and port pilots and the sailing conditions of the ship in specific conditions. Choosing the optimal speed of ships in port, including the effect of shallow depth, can reduce fuel consumption and ship emissions in ports, which is important for the development of green and sustainable ports. In all cases, shipping safety is the highest priority. The main objectives of the article are determining the optimal speed of ships in ports with low clearance, ensuring navigational safety, reducing fuel consumption and emissions, and at the same time creating a sustainable port. The article presents the methodology of optimal ship speed calculation, minimum ship controllable speed maintenance, fuel consumption and emission reduction methodology and their impact on sustainable and green maritime transport and port development. The developed methodology was tested on real ships and with the help of a calibrated simulator, sailing through harbor channels and harbor waters in low clearance conditions.

The switched inertance hydraulic system (SIHS) is a novel high-bandwidth and energy-efficient digital device which can adjust or control flow and pressure by a means that does not rely on throttling the flow and dissipation of power. An SIHS can provide an efficient step-up or step-down of pressure or flow rate by using a digital control signal. In this article, analytical models of an SIHS in a four-port high-speed switching valve configuration are proposed, and the system dynamics and performance are investigated theoretically and experimentally. The flow responses, system characteristics and power consumption can be predicted effectively and accurately by using the proposed models, which were validated by comparing with experiments and with numerical simulation. The four-port configuration is compared with the three-port configuration, and it is concluded that the former one is less efficient for valves of the same size, but provides a bi-direction control capability. As bi-direction control is a common requirement, this constitutes an important contribution to the development of efficient digital hydraulics.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

Despite a significant number of investigations in the field of phosphazene chemistry, the mechanism of this class cyclic compounds formation is still poorly studied. At the same time, a thorough understanding of this process is necessary both for the direct production of phosphazene rings with a given size, and for the controlled cyclization reaction when it is secondary and undesirable. Here we have synthesized a series of short linear phosphazene oligomers with the general formula Cl[PCl2=N]n–PCl3+PCl6– and studied their tendency to form cyclic structures under the influence of elevated temperature or in the presence of nitrogen-containing agents, such as hexamethyldisilazane (HMDS) or ammonium chloride. It was established that linear oligophosphazenes are inert when heated in the absence of the mentioned cyclization agents, and the formation of cyclic products occurs only when these agents are involved in the process. It is for the first time shown the ability to obtain the desired size phosphazene cycle from corresponding linear chain. Known obstacles like side interaction with the PCl6– counterion and a tendency of longer chains to undergo crosslinking elongation instead of cyclization are still relevant and ways to overcome them are being discussed.

In the present study the synthesis of gold nanoparticles (AuNPs) loaded with methotrexate (MTX) has been carried out in order to obtain controlled size and monodispersed nanocarriers, around 20nm. Characterization study shows metallic AuNPs with MTX polydispersed on the surface. MTX is linked by a replacement of citrate by the MTX carboxyl group. The drug release profiles showed faster MTX release when it is conjugated, which leads to the best control of plasma concentration. Also, the enhanced release observed at pH 5 could take advantage of the pH gradients that exist in tumor microenvironments to achieve high local drug concentrations. AuNPs-MTX conjugates were tested by flow cytometry against lung (A-549) and colon (HTC-116) cancer cell lines. Results for A-549 showed a lighter dose-response effect than for colon cancer ones. This could be related to the presence of folate receptors in line HTC-116 on the contrary than line A-549, supporting the specific uptake of folate-conjugated AuNPs-MTX by folate receptor positive tumor cells. Conjugates exhibited considerably higher cytotoxic effects compared with the effects of equal doses of free MTX. Anexin V-PI test sustain as cell death mechanism apoptosis, which is normally disabled in cancer cells.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

The present study explored the effects of a Second-generation mindfulness-based intervention known as Flow Meditation (Meditación-Fluir) in the improvement of life habits. A sample of university students (n = 51) in Spain were randomly assigned to a seven-week mindfulness treatment or a waiting list control group. Results showed that compared to the control group, individuals in the mindfulness group demonstrated significant improvements across all outcome measures, including healthy eating habits (balanced diet, intake rate, snacking between meals, decrease in consumption by emotional states negative, increased consumption by negative emotional states, amount of consumption, meal times, consumption of low-fat products), tobacco, alcohol and cannabis consumption, and resting habits. There were differences between males and females in some of these variables and a better effect of the treatment was evident in the females of the experimental group as compared to males. The Flow Meditation program shows promise for fostering healthy life habits, thus decreasing behaviors related to maladaptive eating, tobacco, alcohol and drug consumption, as well as negative resting habits, in university students. This mindfulness program can significantly contribute in the treatment of eating disorders and addictions, wherein negative emotional states and impulsivity are central features of the condition.

Background: Feasibility trials are preliminary trials that assess the viability and acceptability of intervention studies and the effects of the intervention on intermediate endpoints. Due to their short duration, they are unable to establish the effects of the intervention on long-term clinical outcomes. We propose a novel method that could transform the interpretation of feasibility trials using modified two-stage randomisation analyses. Methods In this two-stage process, we explored the effects of a 6-month feasibility factorial randomised controlled trial (RCT) of lycopene and green tea dietary interventions (ProDiet) on 159 serum metabolic traits in 133 men with raised PSA levels but prostate cancer (PCA) free. In the first stage, we conducted an intention-to-treat analysis, using linear regression to examine the effects of the interventions on metabolic traits, compared to the placebo group and instrumental variable analysis to assess the causal effect of the intervention on the outcomes. In the second stage, we used a two-sample Mendelian Randomization (MR) approach to assess the causal effect of metabolic traits altered by the interventions, on PCA risk, using summary statistics data from an international PCA consortium of 44,825 cancer cases and 27,904 controls. ResultsThe systemic effects of lycopene and green tea supplementation on serum metabolic profile were comparable to the effects of the respective dietary advice interventions (R2= 0.65 and 0.76 for lycopene and green tea respectively). Metabolites which were altered in response to lycopene supplementation were acetate (standard deviation difference versus placebo (β)): 0.69; 95% CI= 0.24, 1.15; p=0.003), valine (β: -0.62; -1.03, -0.02; p=0.004), pyruvate (β: -0.56; -0.95, -0.16; p=0.006), and docosahexaenoic acid (β: -0.50; -085, -0.14; p=0.006). The instrumental variable analysis showed there was no evidence that green tea altered the metabolome, but lycopene was associated with an increase in acetate (β=2.13; p=0.006) and decreases in pyruvate (β=-1.90; p=0.009), valine (β=-1.79; p=0.023), diacylglycerol (β=-1.81; p=0.026), alanine (β=-1.55; p=0.015) and DHA (p=0.097), where the regression coefficient represents the standard deviation (SD) difference in metabolite measures per unit change in lycopene (µmol/L) or EGCG (nM).Using MR, a genetically instrumented SD increase in pyruvate increased the odds of PCA by 1.29 (1.03, 1.62; p=0.027). Conclusion Using a two-stage randomization analysis in a feasibility RCT, we found that lycopene lowered levels of pyruvate, which our Mendelian randomization analysis suggests may be causally related to reduced PCA risk.

The aim of this work is to analyze and investigate the shape preserving properties of ternary 4-point non-stationary interpolating subdivision schemes constructed by Beccari et al. [1] with a tension parameter !k+1 which can reproducing exponential. Moreover, the conditions on the initial control points are developed that allow user to generate shape preserving limit curves after a nite number of subdivision steps and generalize these results in limiting case. Signicance of derived conditions are illustrated through graphs and the whole discussion is followed by examples.

Halloysite nanotubes (HNTs) are natural occurring mineral clay nanotubes that have excellent application potential in different fields. However, HNTs are heterogeneous in size, surface charge and formation of surfacial hydrogen bond, which lead to weak affinity and aggregation at a certain extent. It is very important to modify the HNTs’ surface to expand its applications. In this review, the structural characteristics, performance and the related applications of surface-modified HNTs are reviewed. We focus on the surface-modified variation of HNTs, the effects of surface modification on the materials and related applications in various regions. In addition, future prospects and the meaning of surface modification were also discussed in HNTs studies. This review provides a reference for the application of HNTs modifications in the field of new nanomaterials.

Hydrogels evolved as an outstanding carrier material for local and controlled drug delivery that tend to the shortcomings of old conventional dosage forms for small drugs (NSAIDS) and large peptides and proteins. Aqueous swellable and crosslinked polymeric network structure of hydrogels is composed of various natural, synthetic and semisynthetic biodegradable polymers. Hydrogels have remarkable properties of functionality, reversibility, sterilizability, and biocompatibility. All these dynamic properties of hydrogels have increased the interest in their use as a carrier for peptides and proteins to be released slowly in a sustained manner. The therapeutical peptide and proteins are remarkable therapeutic agents in today’s world that allows the treatment of severe, chronic and life‐threatening diseases, such as diabetes, rheumatoid arthritis, hepatitis in an easy manner. Despite few limitations, hydrogels provide fine tuning of proteins and peptides delivery with enormous impact in clinical medicine. The primary objective of this article is to review current issues concerned with the therapeutics peptides and proteins and impact of remarkable properties of hydrogels on these therapeutic agents. Different routes for pharmaceutical peptides and proteins and superiority over other drugs candidates are presented. The article will also review literature concerning classification of hydrogels on different basis, polymers used, release mechanisms their physical and chemical characteristics and diverse applications.

A new approach for the preparation of polymer brush was developed via the union of controlled/“living” radical polymerization and click chemistry. The application of the approach realized the more quickly and accurate design and synthesis of the polymer brushes. A novel functional polymer brush of poly(acrylonitrile-g-glycidyl methacrylate) with tremendous application potential in the field of biology has been successfully synthesized via the new approach. The reaction conditions of click chemistry were optimized with the reaction time and the reactant ratio and judged from UV-vis spectra. Under the optimum of click chemistry, the novel functional polymer brushes were prepared. The GPC, FTIR analyses, 1H NMR spectrum and TGA were employed to ensure the successful synthesis of poly(acrylonitrile-g-glycidyl methacrylate) polymer brushes.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

In response to growing industrial demands, necessitated by larger ships and increased cargo volumes, many port authorities worldwide are undertaking a significant expansion of their infrastructure to increase their capacity. Significant expansion raises challenges such as potential congestion and environmental concerns, especially for port located in urban area as the case study explored in this paper. To address these issues, the study employs a combination of scenario analysis developed in collaboration with the port authority and logistic system simulation. This approach assesses the capacity of existing access gates to handle the increased trucking traffic and optimizes the unloading process of construction trucks at a new terminal. Key findings suggest that while the current gate capacities are adequate, optimizing unloading times at the new terminal is critical to prevent road congestion in urban area before the gate and reduce negative impacts such as sound and atmospheric pollution. The study advocates for an appointment system during peak hours to manage traffic flow effectively and underscores the importance of collaboration between the city and port authorities in managing truck traffic to mitigate congestion on the city side. Nonetheless, the study recognizes certain constraints, including the incomplete evaluation of the influence of intermodal transport on truck traffic. Furthermore, the study emphasizes the need for future research to consider the correlation between vehicle numbers and service levels, aiming to effectively adjust the time in the system.

This article describes an approach for optimising sensor-controlled systems through minimal intervention, utilising Fuzzy Linear Systems of Equations (FLSE). Staring with a generalised model of the system behaviour, incorporating an array of control units, environmental sensors, and an expert knowledge base. The described problems of detecting the level of intervention needed to change the system state to another is handled with the help of developed methods for solving the inverse problem for FLSE. By achieving minimal intervention, we ensure that system adjustments effective, economically optimal and non-intrusive. A MATLAB-based implementation is presented.

The agricultural sector faces challenges due to climate change and the growing global population. Alkaline stress could adversely impact plant growth and crop production. This stressor diminishes water quality essential for crop cultivation, consequently impairing plant growth and overall productivity. Gamma-aminobutyric acid (GABA), a non-protein amino acid, may exhibit multifaceted roles in plant responses to adverse environmental conditions. Optimization of crop production in controlled environmental agriculture under artificial light attracted much attention. In the present study, we investigated the effects of different light spectra and GABA concentrations on Lollo Rosso lettuce plants under alkaline stress. Seedlings were placed under different light spectra [red (R), blue (B), white (W), 3R:1B, and 2R:1B:1far-red (FR)] and treated by GABA (0 and 50 µmol). Alkaline conditions were instituted by applying NaHCO3 at a concentration of 40 mM. The experiment incorporated a control treatment without NaHCO3. In general, R light exposure caused the highest growth performance of lettuce plants. GABA augmented biomass production in control and alkaline-treated plants across all light spectra. Additionally, it increased the concentrations of photosynthetic and protective pigments under alkaline conditions. GABA also improved the photosynthetic performance under all light spectra. Non-photochemical quenching and pigmentation were enhanced by exposure to B light, especially in plants treated with GABA. Alkaline stress induced an increase in soluble carbohydrate content in the lettuce leaves. These findings highlight the support of GABA application in facilitating coping plants to alkaline stress.

The design of randomized controlled trials for low-resource settings has unique challenges. One challenge is ensuring recruitment success in the face of a lack of information about prevalence of disease in the population. What disease burden data may exist is old and from distant regions, adding guesswork into site design. This leads to a high chance that the sample size will not be recruited in any reasonable timeframe—a challenge even in high-resource settings. While cross-sectional prevalence studies could be used as a type of feasibility study informing trials by generating near real-time prevalence estimates for the future trial site, such studies take years to complete. This duration makes insertion of such a study in trial design impossible. An empirically supported combination of new approaches that sidesteps unnecessary hurdles is presented, the Pop-Up Prevalence with Private Ethics (PUPPE) design. PUPPE includes using a COVID-validated, more targeted method of data collection, use of accepted ethics review from universities or hospitals to avoid lengthy public ethics review, and—if needed—post-study in silico participant randomization. Only this design would enable clinical trial designers to insert fit-for-purpose prevalence studies within the design phase of their trials, leading to informative outcomes.

Basil (Ocimum basilicum L.) is one of the important medicinal and aromatic plants. Light intensity is an indispensable factor for plants due to its effect on photosynthesis and physiological processes. Here, we investigated the impact of light intensities and harvesting times on the photosynthesis of green and purple basil. The experiment involved subjecting the plants to three different sunlight levels for 12 days: complete – 100%, 50%, and 30% sunlight. In addition, we scrutinize the harvesting time. The highest levels of photosynthetic and protective pigments were detected under full sunlight conditions in the purple basil harvested at noon. The highest levels of soluble and storage carbohydrates were recorded in the purple basil grown under full sunlight and harvested in the early morning. In contrast, their lowest levels were obtained in plants grown under 30% sunlight and harvested at noon time. Under all light treatments, the maximum quantum yield of photosystem II (FV/FM) was detected at 4 a.m. in both basil varieties; it decreased at noon and increased again at 5 p.m. Non-Photochemical Quenching (NPQ) got most elevated in the green variety under all light intensities at noon. However the highest NPQ was detected in the purple variety at 8 a.m. The NPQ was lowest in both basil varieties during the early morning and afternoon. Full sunlight at noon caused temporary photoinhibition and reduced car-bohydrates while enhancing pigment concentration and photo-protective mechanisms in basil plants.

The efficacy of time-restricted feeding for weight loss has not been established as prior studies were limited by lack of controlled isocaloric designs. This study describes the design and implementation of a controlled feeding study evaluating time-restricted feeding. We designed a randomized, controlled, parallel-arm, feeding study comparing time restricted feeding (TRF) to a usual feeding pattern (UFP) for the primary outcome of weight change. Participants were aged 18-69 years with prediabetes and obesity. TRF consumed 80% of calories by 1300, and UFP consumed ≥50% of calories after 1700. Both arms consumed identical macro- and micro-nutrients, based on a healthy palatable diet. We calculated individual calorie requirements which were maintained throughout the intervention. We randomized 41 participants who all completed the study. The desired distribution of calories across feeding windows in both arms was achieved, as were weekly averages for macronutrients and micronutrients. All randomized participants completed the study. We actively monitored participants and adapted diets to facilitate adherence. We provide the first report, to our knowledge, on the design and implementation of a feeding study that isolated the effect of meal timing on weight, while maintaining constant caloric intake and identical diets during the study period.

Objectives: To determine the prevalence of controlled systemic hypertension and its associated risk factors among the hypertensive patients who attended the clinic at Mbeya Zonal Referral Hospital in Tanzania. Methods: A descriptive cross-sectional quantitative study was used determine the prevalence of co to 252 hypertensive patients were recruited during clinic visit from September to November 2020 and participant was randomly selected interviews using structured self-administered questionnaires. Data was analyzed using chi square test to find the risk factors associated with controlled hypertension. Results: Among 252 participants, 94(39.7%) individuals with controlled hypertension giving the prevalence of controlled hypertension. The proportion of females with controlled hypertension was slightly higher than male (49 females to 45 males). The prevalence of uncontrolled hypertension was 152(60.3%) participants. The prevalence of controlled hypertension was higher among patients who have regular clinic visit (p< .05) and have daily adherence to their anti-hypertensive medication. A similar trend was observed among participants without financial challenges to attend clinic, short duration of illness, higher level of education and there was no association between age, sex, marital status, smoking, alcohol consumption, having health insurance and having chronic illness. Conclusion: Prevalence of controlled hypertension is higher among patients who have regular clinic visit and have daily adherence to their anti-hypertensive medication. Also, it is higher among participants without financial challenges to attend clinic so they can have regular clinic visit and checkup. Reinforcement on regular drug intake and clinic visit, good nutrition and reduced salt intake and modifying lifestyles of patient with hypertension is important.

Doxorubicin, a member of the anthracycline family, is a common anticancer agent often used as a first line treatment for the wide spectrum of cancers. Doxorubicin-based chemotherapy, although effective, is associated with serious side effects, such as irreversible cardiotoxicity or nephrotoxicity. Those often life-threatening adverse risks, responsible for the elongation of the patients' recuperation period and increasing medical expenses, have prompted the need for creating novel and safer drug delivery systems. Among many proposed concepts, polymeric nanocarriers are shown to be a promising approach, allowing for controlled and selective drug delivery simultaneously enhancing its activity towards cancerous cells and reducing toxic effects on healthy tissues. This article is a chronological examination of the history of the work progress on polymeric nanostructures, designed as efficient doxorubicin nanocarriers, with the emphasis on the main achievements of 2010-2020. Numerous publications have been reviewed to provide an essential summation of the nanopolymer types and their essential properties, mechanisms towards efficient drug delivery, as well as active targeting stimuli-responsive strategies that are currently utilized in the doxorubicin transportation field.

Polyhydroxyalkanoate (PHA) co-polymers show relatively higher in vivo degradation rate compared to other PHAs thus they received a great deal of attention for a wide range of medical applications. Nanoparticles (NPs) loaded with poorly water soluble anticancer drug docetaxel (DCX) were produced using poly 3-hydroxybutyrate-co-4-hydroxybutyrate, P(3HB-co-4HB), co-polymers biosynthesised from Cupriavidus sp. USMAA1020 isolated from Malaysian environment. Three co-polymers with different molar proportions of 4-hydroxybutirate (4HB) were used: 16% (PHB16), 30% (PHB30) and 70% (PHB70) 4HB-containing P(3HB-co-4HB). Blank and DCX loaded nanoparticles were then characterized for their size and size distribution, surface charge, encapsulation efficiency and drug release. Pre-formulation studies showed that an optimised formulation could be achieved through the emulsification/solvent evaporation method using PHB70 with the addition of 1.0% PVA, as stabilizer and 0.03% VitE-TPGS, as surfactant. DCX-loaded PHB70 nanoparticles (DCX-PHB70) gave the desired particle size distribution in term of average particles sizes around 150 nm and narrow particle size distribution (PDI below 0.100). The encapsulation efficiencies result showed that at 30% w/w drug-to-polymer ratio: DCX- PHB16 NPs were able to encapsulate up to 42% of DCX; DCX-PHB30 NPs encapsulated up to 46% of DCX and DCX-PHB70 NPs encapsulated up to 50% of DCX within the nanoparticles system. Approximately 60% of DCX was released from the DCX-PHB70 NPs within 7 days for 5%, 10% and 20% of drug to polymer ratio while for the 30% and 40% drug to polymer ratios, an almost complete drug release (98%) after 7 days of incubation was observed.

In recent years, polyureas with dynamic hindered urea bonds (HUBs), as a class of promising biomedical polymers, have attracted attention as a benefit of their controlled hydrolytic property. The effect of the chemical structures on the properties of polyureas and their assemblies was rarely reported. In this study, four kinds of polyureas with different chemical groups have been synthesized, and the polyurea from cyclohexyl diisocyanate and tert-butyl diamine showed the fastest hydrolytic rate. The amphiphilic polyurea composed of hydrophobic cyclohexyl-tert-butyl polyurea and hydrophilic poly(ethylene glycol) was synthesized for controlled delivery of antitumor drug paclitaxel (PTX). The PTX-loaded PEGylated polyurea micelle more effectively entered into the murine breast cancer 4T1 cells and inhibited the corresponding tumor growth in vitro and in vivo. Therefore, the PEGylated polyurea with adjustable degradation might be a promising polymer matrix for drug delivery.

One-dimensional nanostructures such as silver nanowires (AgNWs) have attracted considerable attention owing to their outstanding electrical, thermal and antimicrobial properties; however, their application in the prevention of infections linked to bone tissue regeneration interventions has not yet been explored. Here we report on the development of an innovative scaffold prepared from chitosan, composite hydroxyapatite and AgNWs (CS-HACS-AgNWs) having both bioactive and antibacterial properties. In vitro results highlighted the antibacterial potential of AgNWs against both gram-positive and gram-negative bacteria. The CS-HACS-AgNWs composite scaffold demonstrated suitable Ca/P deposition, improved gel strength, reduced gelation time, and sustained Ag+ release within therapeutic concentrations. Antibacterial studies showed that the composite formulation was capable of inhibiting bacterial growth in suspension and of completely preventing biofilm formation on the scaffold in the presence of resistant strains. The hydrogels were also shown to be biocompatible, allowing cell proliferation. In summary, the developed CS-HACS-AgNWs composite hydrogels demonstrated significant potential as a scaffold material to be employed in bone regenerative medicine, as it presents enhanced mechanical strength combined with the ability to allow calcium salts deposition, while efficiently decreasing the risk of infections. The results presented justify further investigations into potential clinical applications of these materials.

Since autism was first recognised, prevalence has increased rapidly. The growing economic as well as social cost to society can only be mitigated by effective interventions and supports. It is therefore not surprising that most governments have developed public policy documents to address the management of autism. Over the past 40-50 years, meaningful evidence has accrued showing that interventions based on the scientific discipline of Applied Behaviour Analysis (ABA) can help people with autism reach their potential. In view of this, nearly all of North America has laws to mandate that ABA-based interventions are available through the health care systems. In contrast, across Europe there are no such laws. In fact, the National Institute for Health and Care Excellence (NICE), the body guiding health and social policy in the UK, concluded that it could not find any evidence to support ABA, and therefore could not recommend it. This paper addresses the reasons for these diametrically opposed perspectives. In particular, it examines what happens when health and social care policy is misinformed about effective autism intervention.

Responding to an urgent call for effective and cost-efficient enforcement of emission regulations from ocean-going vessels (OGVs) at sea, the Royal Belgian Institute of Natural Sciences, one of the 17 official partners of the Belgian coastguard structure, launched its airborne sniffer program in 2015. A custom-built sniffer sensor was installed on board of the Belgian coastguard aircraft and has been used for the in-situ measurement of SO2 and NOx in OGV exhausts, providing non-compliance alerts to port inspection authorities in Belgium and other EU member states. To guarantee the consistency in quality and reliability of the airborne non-compliance alerts, the standard operational procedures and measurement methodology have been described and recorded in a sniffer quality management system (SQMS). As part of the SQMS, alerting thresholds for non-compliance with SO2 and NOx standards were defined based on the emission limits and the measurement uncertainty. In addition, compliant measurements for the fuel sulfur content (FSC) were shared through Thetis-EU, which is the sulfur inspection database hosted by the European Maritime Safety Agency (EMSA). By providing both non-compliance alerts and compliant measurements to port inspection authorities, the coastguard aircraft fulfills a first-step in the enforcement chain. This article demonstrates that the reported alerts have not only led to several sanctions, but the analysis also showed that the provision of airborne alerts improved the efficiency of the port inspection authorities drastically, resulting in a cost-efficient improvement of their enforcement strategy. Port inspection authorities were able to follow-up on 46% of the generated FSC alerts. In addition, 43% of the alerted OGVs, which were followed up, were confirmed as non-compliant after a port inspection. Accordingly, conditions were in place to effectively sanction 20% of the non-compliant observations. For NOx alerts, a limited follow-up was done by port inspection authorities and none of the alerts were confirmed by those inspections, which is mainly due to the lack of suitable inspection mechanisms and the absence of additional EU implementation regulations on NOx emission inspections. Aiming at paving the way for a stricter enforcement of airborne non-compliance alerts, a validation analysis was done between the airborne FSC measurements and reference FSC measurements. In addition to onboard measurements from exhaust gas cleaning systems (EGCS), analyzes of fuel samples were also carried out by port inspection authorities in order to acquire reference measurements. The validation analysis presented in this study showed that the empiric deviation of the airborne FSC measurements with the reference measurements was significantly lower than the uncertainty used in the reporting thresholds. It has also been shown that aerial measurements provide evidence-based data that, given an appropriate confidence interval, has the potential to be considered reliable legal evidence.

Proposed as a response to the increasing global need for environmental protection, a green port balances economic vibrancy and environmental protection. However, because exhaust emissions (e.g., CO2 or sulfide) are difficult to monitor in and around ports, data on such emissions are often incomplete, which hinders research on this topic. To remedy this problem, this study aimed to formulate a method for collecting CO2 emissions data at their source; this method was applied to collect real-world operating data from a large container-handling company in Taiwan. Specifically, to account for undesirable outputs, we formulated a method that combines (1) data envelopment analysis based on a modified slack-based measure and (2) a multichoice goal programming approach. We found that rubber-tired gantry cranes are the greenest and should be used. Our findings aid port managers in selecting port equipment that best balances between environmental protection and profitability.

In this paper, precise examination of multi-port antennas with large mutual coupling between the ports is studied. For this purpose, some vital parameters such as active reflection coefficients and realised gain are emphasized. The main motivation of this research is the ignorance of this issue in several recently published papers. Hence, corrections and criticisms to some recently reported results are presented. At first, a microstrip patch consisting of two inverted U-slots is re-examined, which has been proposed in a recently published paper for wideband applications. However, the authors did not present satisfactory results to indicate the performance of the proposed structure. In reverse, some important parameters such as the antenna gain appear to be incorrectly reported. In this paper, the characteristics of the antenna are compared with a simple 50 Ω microstrip line excited by two probes, indicating no significant differences. In the remainder of this paper, some corrections are provided on two examples of wide-beam circularly polarised multi-fed antennas for satellite applications. The first example is the multi-fed spiral antennas with folded arms, which have been proposed as the widebeam antennas at 435 MHz. It is indicated that the antenna height should be increased for better performance. The second example is the quadrifilar square helical antennas with folded arms, which have been proposed as the widebeam antennas for 435 MHz with minor responses at 145 MHz. Some corrections are presented on the previously reported minor responses at 145 MHz.

Transdermal drug delivery systems have become an intriguing research topic in healthcare technology and one of the most frequently developed pharmaceutical products in the global market. In recent years, researchers and pharmaceutical companies have made significant progress in developing new solutions in the field. This study sheds light on current trends, collaboration patterns, research hotspots, and emerging frontiers of transdermal drug delivery. Herein, a bib-liometric and patent analysis of data recovered from Scopus and The Lens databases, respectively, is reported over the last 20 years. From 2000 to 2022, the annual global publications increased from 131 in 2000 to 659 in 2022. Researchers in the United States, China, and India produced the highest number of publications. Likewise, most patent applications have been filed in the USA, China, and Europe. The recovered patents are 7,275, grouped into 2,997 patent families, of which 314 were granted. This study could support the work of decision-makers, scientific managers, or scientists to create new business opportunities or save money, time, and intellectual capital, thus, defining when a research or technology project should be a priority or not.

The cross-linked microspheres were prepared and loaded with Favipiravir SARS-CoV-2 antiviral drug, by copolymerization of chitosan (CS) with a polysaccharide extracted from fresh pomegranate peels. Moreover, glutaraldehyde (Glu) has been used as chemical cross-linker ,and sodium hexametaphosphate (SHMP) as physical cross-linker. The extracted polysaccharide was analyzed and different techniques have been used and the analyses leads to the fact that it is pectin .The surface morphology of the prepared microspheres was studied use scanning electron microscope where the size and the shape factor (S) of Glu microspheres have shown high values(74.27μm) and (0.852) respectively means their surfaces are tends to roughness, whereas the SHMP microspheres have shown size particle(20.47μm)and shape factor (0.748) which gives indication that the SHMP microspheres have smooth surfaces. The swelling studies have shown that Glu microspheres have higher degree of swelling which means SHMP microspheres are more compact. The prepared microspheres have shown more Loading percentage of Favipiravir antiviral drug in SHMP microspheres(37%w/w)in comparison with Glu microspheres(35%w/w) where the electrostatic interaction between the Favipiravir ions and SHMP anions help for more loading. The microspheres prepared under different types of cross-linking have shown initially burst release of Favipiravir and followed by a step of controlled release for a certain time where its period depends on the pH of the release media. Both Glu and SHMP cross-linked microspheres have shown high controlled release time in buffered release solution of pH 7.4 and for a less periods in pH 1.3 and pH 9.4 which may related to the type of electrostatic interactions between drug and polymer system and their reactions with release solution ions.

Main purposes and research question: Wheat is the second largest grain crop by tonnage in the world and the largest in Denmark. Given the observed, adverse impacts on wheat yields of climate change and the importance of wheat in the human diet, the purpose of this study was to use life cycle assessment to compare conventional wheat farming with indoor vertical farming using hydroponics. Methods: Life Cycle Assessment was used to assess the base case systems up to the “farm gate” for 1 tonne of wheat grain. The processes contributing most of the impacts were identified, and scenarios were assessed to determine how much the impacts could be reduced. Results: The conventional system outperformed the base case vertical system in every impact category, due to the electricity consumption in the lighting system. The scenarios included increasing the efficiency of the LED lighting and using 100% wind energy, but the conventional system still outperformed the vertical system by significant margins in all impact categories. This was due to the low photosynthetic conversion efficiency and the high energy density of wheat. Conclusions: Until significant improvements are made to lighting efficiency, the photosynthesis conversion efficiency of wheat, new wheat variants designed for vertical gardens and the sustainability of electricity supply, conventional wheat production will be environmentally preferable and vertical gardens would be advised to focus on food products with low energy densities.

The manipulation of participant allocation in randomized controlled trials to achieve equal groups sizes may introduce allocation bias potentially leading to larger treatment effect estimates. This study aimed to estimate the proportion of nursing trials that have precisely equal group sizes and examine if there was an association with trial outcome. Data were extracted from a sample of 148 randomized controlled trials published in nursing science journals in 2017. One hundred trials (68%) had precisely equal group sizes. Respectively, a positive outcome was reported in 70% and 58% of trials with equal/unequal groups. Trials from Asia were more likely to have equal group sizes than those from the rest of the world. Most trials reported a sample size calculation (n=105, 71%). In a third of trials (n=36, 34%), the number of participants recruited precisely matched the requirement of the sample size calculation; this was significantly more common in studies with equal group sizes. The high number of nursing trials with equal groups may suggest nurses con-ducting clinical trials are manipulating participant allocation to ensure equal group size increasing the risk of bias.

Vertical farming (VF) is a potential solution for the production of high-quality, accessible, and climate-friendly nutrition for growing urban populations. However, to realize VF’s potential as a sustainable food source, innovative technologies are required to ensure that VF can be industrialized on a massive scale and extended beyond leafy greens and fruits into the production of food staples or row crops. A major obstacle to the economic and environmental sustainability of VF is the lighting energy consumed. While technological advances have improved the energy efficiency of VF lighting systems, there has been insufficient research into biostimulation as an approach to reduce energy needs. We conducted a controlled trial to investigate the application of a phycocyanin-rich Spirulina extract (PRSE) as a biostimulant in hydroponically grown, vertically farmed lettuce (Lactuca sativa and Salanova®). PRSE application reduced the time from seeding to harvest by 6 days, increased yield by 12.5%, and improved quality including color, taste, texture, antioxidant flavonoid levels and shelf life. Metagenomic analysis of the microbial community of the nutrient solution indicated that PRSE increased the overall bacterial diversity including raising the abundance of Actinobacteria and Firmicutes and reducing the abundance of potentially pathogenic bacteria. This preliminary study demonstrates that microalgae-derived biostimulants may play an important role in improving the economic and environmental sustainability of VF.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

Transcriptionally controlled tumor protein (TCTP) is a highly conserved protein performing a large number of cellular functions by binding with various partner proteins. The importance of its roles in many diseases requires an assay method to find regulatory compounds. However, the molecular characteristics of TCTP made it difficult to search for chemicals interacting with it. In this study, a tryptophan-based assay method was designed and Y151W mutant TCTP was constructed to search binding chemicals. Since there is no tryptophan in the native sequence of TCTP, the incorporation of tryptophan in the Y151W mutant was very effective to establish the method. A flavonoid library was employed to the assay with the method. With the native and Y151W mutant TCTPs, three flavonoids such as morin, myricetin and isobavachalcone have been found to interact with TCTP. Combined with native gel electrophoresis, the binding region of isobavachalcone was suggested to be the flexible loop of TCTP. This approach can be easily applicable to find binding compounds of proteins with similar molecular characteristics of TCTP.

Transdermal drug delivery (TDD) is one of the key approaches for treating diseases, avoiding first-pass effects, reducing systemic adverse drug reactions and improving patient compliance. Microneedling, iontophoresis, electroporation, laser ablation and ultrasound facilitation are often used to improve the efficiency of TDD. Among them, microneedling is a relatively simple and efficient means of drug delivery. Microneedles usually consist of micron-sized needles (50-900 μm in length) in arrays that can successfully penetrate the stratum corneum and deliver drugs in a minimally invasive manner below the stratum corneum without touching the blood vessels and nerves in the dermis, improving patient compliance. Hydrogel-forming microneedles (HFMNs) are safe, non-toxic, no residual matrix material, high drug loading capacity, controlled drug release and are suitable for long-term, multiple drug delivery. This work reviewed the characteristics of skin structure and transdermal drug delivery; introduced TDD strategies based on hydrogel microneedles; summarised the characteristics of HFMNs TDD systems and the evaluation methods of HFMNs; and the application of HFMNs drug delivery systems in disease treatment. The HFMNs drug delivery system has a wide scope for development, but the translation to clinical application still has more challenges.

Honey bees (Apis mellifera L.) express complex behavioral patterns (aggressiveness) to exhibit defensive mechanisms for their survival. Their phenotypic expression of aggressive behavior is influenced by internal and external stimuli. Knowledge of this behavior is recently important though beekeepers are still faced with the challenges of selecting aggressive and less-aggressive bred lines. Field evaluation of aggressiveness among bred lines of honey bees is required to overcome the challenges. Chemical cues (alarm pheromone and isopentyl acetate mixed with paraffin oil), physical and visual stimuli (dark leather suede, colony marbling and suede jiggling) were used to evaluate aggressiveness and orientation among five bred lines of honeybee colonies. Our results showed that both chemical assays recruited bees but the time of recruitment was significantly lower for alarm pheromone. Honeybees’ response to both assays culminated to stings which differed among bred lines for alarm pheromone and paraffin when colonies were marbled. Honeybee aggression varied among bred lines and was higher in more aggressive bred lines compared to less-aggressive bred lines. Our findings suggest that it is crucial to repeatedly evaluate orientation aggressiveness at the colony level and among bred lines when selecting breeding colonies.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

The interactions of chemotherapeutic drugs with nanocage protein apoferritin (APO) are the key features in the effective encapsulation and release of highly toxic drugs in APO-based controlled drug delivery systems. The encapsulation enables mitigating the drugs side effects, collateral damage to healthy cells, and adverse immune reactions. Herein, the interactions of anthracycline drugs with APO were studied to assess the effect of drug lipophilicity on their encapsulation excess n and in vitro activity. Anthracycline drugs, including doxorubicin (DOX), epirubicin (EPI), daunorubicin (DAU), and idarubicin (IDA), with lipophilicity P from 0.8 to 15, were investigated. We have found that in addition to hydrogen-bonded supramolecular ensemble formation with n = 24, there are two other competing contributions that enable increasing n under strong polar interactions (APO(DOX)) or under strong hydrophobic interactions (APO(IDA) of the highest efficacy). The encapsulation/release processes were investigated using UV-Vis, fluorescence, circular dichroism, and FTIR spectroscopies. In vitro cytotoxicity/growth inhibition tests and flow cytometry corroborate high apoptotic activity of APO(drugs) against targeted MDA-MB-231 adenocarcinoma and HeLa cancer cells, and low activity against non-tumorigenic MCF10A cells, demonstrating targeting ability of nanodrugs. A model for molecular interactions between anthracyclines and APO nanocarriers was developed, and the relationships derived compared with experimental results.

Objectives To determine the effects of omega-3 polyunsaturated fatty acids (ω-3 PUFA) from animal and plant sources on glucolipid metabolism and lipoprotein subfractions in type 2 diabetic patients with dyslipidemia. Methods Participants were recruited from the diabetes clinic at the Guanlin Hospital, Yixing City in Jiangsu province, China, from March 2017 through June 2017. Ninety participants were randomly assigned to take 3g/day fish oil (FO, containing EPA and DHA), 3g/day perilla oil (PO, containing ALA), or 3g/day blend oil containing fish oil and linseed oil (BO, containing EPA, DHA and ALA) for 3 months. The levels of serum glucose, glycated hemoglobin (HbA1c), C-peptide, triglyceride (TG), total cholesterol (TC), high-density lipoprotein (HDL), low-density lipoprotein (LDL), non-HDL, apolipoprotein A1 (Apo A1), apolipoprotein B (Apo B), lipoprotein a (Lp(a)), and free fatty acids were determined at baseline and after the 3 months. In addition, four fatty acids in serum and red blood cells membranes (RBCm) were analyzed using gas chromatography-mass spectrometry. The Lipoprint System was used to determine the lipoprotein subfractions. Results All 90 participants completed the final 3-month follow-up at the end of the study. After three months of intervention, blood glucose and HbA1c levels in the PO group were significantly lower than those at the baseline (p < 0.05). On the other hand, in the BO group, the HbA1c, non-HDL, Apo A1 and Lp(a) levels were significantly lower, while the C-peptide levels were significantly higher after intervention compared to the baseline (p < 0.05). In the FO group, the HbA1c and TG levels were significantly lower after the intervention compared to the baseline (p < 0.05). In addition, at the end of the study, there was significant increase in the levels of DPA and DHA in serum and RBCm of the FO group (p < 0.05), while in the BO group, there was significant increase in the levels of EPA, DPA and DHA in RBCm (p < 0.05). Finally, the FO group had the highest levels of large HDL subfractions compared to the BO and PO groups, but had the lowest levels of small HDL subfractions among the three groups. Conclusion For patients with diabetes, plant-derived ω-3 PUFAs are more effective at controlling blood glucose than animal-derived ω-3 PUFAs. However, animal-derived ω-3 PUFAs play a critical role in controlling blood lipids. Particularly, fish oil can effectively increase the beneficial large HDL subfractions and reduce the nonbeneficial small HDL subfractions. Both the animal- and plant-derived ω - 3 PUFAs have practical value in improving glucose and lipids metabolism in T2DM patients with dyslipidemia.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

This review aims to consolidate varied information regarding Port Scanning, and examine the tools, techniques, and detection algorithms used. It explores TCP SYN, Full TCP, UDP, and stealth scans, and shows their functions and abilities. Paired with these techniques, it also shows the tools that they can be used by, such as NMap, Zmap, and MASSCAN. It discusses the various detection techniques such as Signature and Anomaly based detection, and discusses the real world impact of this technology, while commenting on the legal and ethical issues posed.

Hypertension (HTN) is the foremost contributor to cardiovascular diseases (CVD), which remain a leading cause of death. However, adherence to the properly prescribed dosage form is critical and challenging for patients with chronic diseases such as HTN to prevent illness progression and death. The study’s objective was to develop AMB-loaded subcutaneous implants to reduce the frequency of administration, thus improving patient compliance during HTN management. AMB subcutaneous implants were prepared using continuous hot melt extrusion technology using PCL and PLGA with dimensions of 7.5 cm (length) by 2 mm (diameter). The implants were characterized for thermal characteristics, drug-excipient incompatibilities, surface morphology, fracturability, in vitro release, and stability studies. DSC showed that the drug was in the crystalline state in the fabricated implants. Scanning Electron Microscopy (SEM) revealed a smooth surface. The lead formulation presented good drug content, showed an extended drug release profile over 30 days, and followed zero-order release kinetics with a mean dissolution time of 15 days. The formulation was stable over 30 days in accelerated stability conditions (the last time point was tested, 40℃/75% RH), and the release profile was similar to the initial drug release profile. The lead formulation showed good fracturability during textural analysis. Therefore, the hot melt extruded implants could be an alternative management strategy for conventional amlodipine besylate (AMB) formulation.

Thermostatically controlled loads have great potential to make a significant contribution to improving energy efficiency in the building sector, which is responsible for 40% of greenhouse gas emissions in the EU. This, in addition to the environmental damage, represents a huge expense in the electricity bill. Therefore, it is very important to train engineers on how to design energy management systems for TCLs. With this goal in mind, it would be very useful to have a simulation-based educational tool (SBET) to understand thermostatically controlled loads, their characteristics and possibilities in energy efficiency. In addition, it would be very useful if this tool could be introduced in engineering curricula to help students to be better trained and enter the labor market with more opportunities. Based on the shortcomings detected, this work develops a SBET specifically designed to teach about TCLs (SBET-TCLs), both about their intrinsic characteristics and their better management. To verify the developed SBET-TCL, it has been tested in a real scenario: A survey was carried out among the students of the subject 'Alternative Energy Sources' of the degrees of Industrial Engineering. The results show that the use of SBET-TCL has very positive effects on the learning process.

Aronia berries contain antioxidants that may have health promoting properties e.g., demonstrated positive effects on hypertension and dyslipidemia. There is a close link between cardiovascular diseases and hypertension and dyslipidemia, and cardiovascular events are the leading cause of death among subjects with T2D. Thus, we investigated the effect of 8 weeks supplementation with fermented aronia extract (FAE), non-fermented aronia extract (AE) and placebo on cardiovascular risk factors. The extracts were incorporated into snack bars containing 34 g (37%) aronia extract, or 17 g (21%) wheat bran for placebo, as well as raisins and coconut oil. The study was randomized and blinded with a triple-cross-over design. We examined the effects of aronia extracts on blood pressure, adiponectin and high-sensitive C-reactive protein and found no effects. After supplementation with placebo, there were significantly higher total-cholesterol, LDL-cholesterol, and HDL-cholesterol, with the placebo group showing significantly higher increases in total-cholesterol and LDL-cholesterol than the FAE group. Furthermore, we observed an increase in HDL-cholesterol in the AE group and an increase in triglyceride in the FAE group. Thus, we assume that raisins may have increased the participants’ cholesterol levels, however, with both AE and FAE having the potential to prevent this increase.

Post-harvest handling and ripening techniques have an impact on peach quality and shelf life, which has a big impact on consumer satisfaction and market competitiveness. This review paper examines recent advancements in ripening techniques and post-harvest technologies with the goal of improving peach fruit quality and sustainability. The factors impacting fruit quality after harvest and the physiological changes that occur throughout peach ripening are fully explained. For maintaining peach freshness and reducing losses, novel handling methods like modified atmosphere packaging (MAP) and controlled atmosphere storage (CAS) have been investigated. The study explores the possibilities of nanotechnology applications and low-temperature storage for prolonging shelf life while maintaining texture, flavor, and aroma. Examining the effectiveness and waste reduction potential of automation and mechanization in post-harvest activities. The paper also discusses ethylene-based and non-ethylene-based ripening agents, as well as innovative techniques including gene editing and RNAi technology for controlled and delayed ripening. Analyses are done on how these technologies affect the sensory qualities and nutrient profiles of peaches. The study emphasizes the significance of sustainable practices in the peach industry by focusing on waste reduction, resource efficiency, and circular economy integration. Post-harvest technologies' potential environmental consequences have been taken into consideration and the paper encourages more study and cooperation to increase sustainability.

Despite the expansion of financial institutions and proliferation of mobile financial services, reaching the unbanked and bringing them under formal financial services has become a policy concern in many developing countries. Due to the lack of financial accounts, unbanked people prefer informal, risky, and inconvenient mechanisms for receiving, sending and transferring money. Previous studies rely much on common intervention like no account maintenance and opening fees, easy documentation processes and money subsidies for opening financial accounts. This study aims to examine the impact of the motivational workshop on opening savings accounts through causality among the unbanked people in a setting where the respondents are unbanked despite having all the requirements and many institutional offers for opening savings accounts. We encouraged the unbanked people through a one-hour-long motivational workshop to open saving account. Based on our cross-sectional data and randomized controlled trial experiment among 505 unbanked Village Defense Party (VDP) members at Dhubil Union under Sirajganj in Bangladesh, we have the evidence that motivational workshop positively impacts opening ac-counts by 32.33 percent. However, the account opening rate differs in terms of respondent’s pref-erence for financial institutions. Our study also finds that unbanked people have the highest pref-erence for mobile financial services for opening accounts resulting in 15.33 percent. The result of the study has some policy implications for adopting effective strategies of financial access in many developing countries.

Indoor crop cultivation systems such as vertical farms or plant factories necessitate artificial lighting. Light spectral quality can affect plant growth and metabolism and, consequently, the amount of biomass produced and the value of the produce. Conflicting results on the effects of light spectrum in different plant species and cultivars make it critical to implement a singular lighting solution. In this study we explored the response of green and red leaf lettuce cultivars (’Aquino’, CVg, or ‘Barlach’, CVr, respectively) to long-term blue-enriched light application (WB). Plants were grown for 30 days in a growth chamber with optimal environmental condi-tions (temperature: 20°C, relative humidity: 60%, ambient CO2, Photon Flux Density (PFD) of 260 µmol m-2 s-1 over an 18-h photoperiod). At 15 days after sowing (DAS) white spectrum LEDs (WW) were compared to WB (λPeak = 423 nm) maintaining the same PFD of 260 µmol m-2 s-1. At 30 DAS, both lettuce cultivars resulted adapted to the blue light variant, though the adaptive re-sponse was specific to the variety. Rosette weight, light use efficiency and maximum operating efficiency of PSII photochemistry in the light, Fv/Fm’, were comparable between the two light treatments. Significant light quality effect was detected on stomatal density and conductance (20% and 17% increase under WB, respectively, in CVg) and, on the modified anthocyanin re-flectance index (mARI) (40% increase under WB, in CVr). Net photosynthesis response was gen-erally stronger in CVg compared to CVr; e.g. net photosynthetic rate, Pn, at 1000 µmol m-2 s-1 PPFD increased from WW to WB by 23% in CVg, compared to 18% in CVr. Results obtained suggest the occurrence of distinct physiological adaptive strategies in green and red pigmented lettuce cultivars to adapt to the higher proportion of blue light environment.

The article is aimed at a brief comparison and analysis of the results of queries to IEEE Xplore and the leading abstract databases Scopus and Web of Science to identify research trends. Some errors in the Author Keywords in Web of Science have been revealed. Therefore, a more detailed analysis was conducted by comparing different types of key terms for IEEE Xplore and Scopus platforms only. I used IEEE Access journal metadata as indexed on both platforms. The sample match for IEEE Xplore and Scopus was achieved by comparing DOI. The IEEE Xplore metadata contains more types of key terms, which provides an advantage in analyzing research trends. Using NSPEC Controlled Terms from expert-compiled vocabulary provides a more stable data, which gives an advantage when considering the change of terms over time. Apriori, an algorithm for finding association rules, has been used to compare co-occurrence of terms for a more detailed description of sample subjects on both platforms. VOSviewer was used to analyze trends in scientific research based on IEEE Xplore data. The 2011-2021 ten-year period was divided into two sub-intervals for comparing the occurrence of Author Keywords, IEEE Terms, and NSPEC Controlled Terms. Using the IEEE conference proceedings bibliometric data, I illustrated the importance of context in estimating the rate of growth of publishing activity on a topic of interest.

Physiological storage disorders continue to cause sizable economic losses in a range of commercially important pomefruit cultivars. Given similar storage regimes, the incidence and severity of browning disorders in the apple cultivar ‘Braeburn’ can vary in different years in a way that can be explained by the interaction of preharvest seasonal and orchard factors. Over a three-year period (2016 to 2019) at the Kompetenzzentrum Obstbau-Bodensee (KOB) in Southwest Germany a range of orchard and storage treatments were conducted for: air temperature during cell division for three weeks post petalfall or during four weeks preharvest, calcium orchard sprays, crop load and harvest timings. Following controlled atmosphere (CA) storage, the disorder incidence for internal browning and cavity formation varied markedly over the three different growing seasons. Crop load treatments strongly influenced the expression of browning disorders in all years. Differences in air temperatures (△ +/- 2 °C compared to ambient) during the cell division period showed little effect on browning incidence. Warm night temperatures (>10 °C) prior to harvest can reduce internal browning in ‘Braeburn’ apples during CA storage and shelf-life.

Background and objectives: Traditional intravenous, patient-controlled analgesia (PCA) uses a fixed-rate continuous background infusion mode. However, some patients suffer from inadequate analgesia or opioid-related adverse effects due to the biphasic pattern of postoperative pain. Therefore, we investigated the postoperative analgesic efficacy of PCA using an optimizing background infusion mode (OBIM), where the background injection rate varies depending on the patient's bolus demand. Materials and Methods: We prospectively enrolled 204 patients who underwent laparoscopic cholecystectomy in a randomized, controlled, double-blind study. Patients were allocated into either the optimizing (group OBIM) or the traditional background infusion group (group TBIM). The numeric rating scale (NRS) score for pain was evaluated at admission to and discharge from the recovery room, as well as at the 6th, 24th, and 48th postoperative hours. Data of bolus demand count, total infused volume, and background infusion rate was downloaded from the PCA device at 30-min intervals until the 48th postoperative hour. Results: The NRS score was not significantly different between groups throughout the postoperative period (P = 0.621), decreasing with time in both groups (P < 0.001). The bolus demand count was not significantly different between groups throughout (P = 0.756). The mean cumulative infused PCA volume was lower in group OBIM [84.0 (95% confidence interval: 78.9−89.1) mL) than in group TBIM [102 (97.8−106.0) mL] (P < 0.001). The background infusion rate was significantly different between groups throughout (P < 0.001); it was higher in group OBIM than in group TBIM before the 12th postoperative hour, and lower from the 18th to the 48th postoperative hours. Conclusions: The OBIM combined with bolus dosing is useful in that it reduces the cumulative PCA volume compared to the TBIM combined with bolus dosing, while yielding comparable postoperative analgesia and bolus demand in patients undergoing laparoscopic cholecystectomy.

The functionalization of polymeric substances is of great interest for the development of innovative materials for advanced applications. For many decades, the functionalization of chitosan has been a convenient way to improve its properties with the aim to prepare new materials with specialized characteristics. In the present article, we summarize the latest methods for the modification and derivatization of chitin and chitosan, trying to introduce specific functional groups under experimental conditions, which allow a control over the macromolecular architecture. This is motivated because an understanding of the interdependence between chemical structure and properties is an important condition for proposing innovative materials. New advances in methods and strategies of functionalization such as click chemistry approach, grafting onto copolymerization, coupling with cyclodextrins and reactions in ionic liquids are discussed.

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed fixed displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. Simulation results demonstrate the four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation.

In this paper, corticosteroid–β-cyclodextrin (β-CD) inclusion complexes have been prepared by Supercritical AntiSolvent (SAS) precipitation to enhance the dissolution rate of dexamethasone (DEX) and prednisolone (PRED), which are poorly water-soluble drugs. The processing of the active principles in the absence of a carrier led to the almost complete extraction of the active principle (the small amount of obtained material precipitates in the form of crystals). The coprecipitation of the ingredients in the presence of β-CD was investigated at different concentrations, pressures, and molar ratios. For both the corticosteroids, the optimized operating conditions were 40 °C, 120 bar, an equimolar ratio, and a concentration in DMSO of 20 mg/mL; these conditions led to the attainment of microparticles with a mean diameter equal to 0.197±0.180 μm and 0.131±0.070 μm in the case of DEX and PRED, respectively. The Job’s method confirmed the formation of inclusion complexes in correspondence with the 1/1 mol/mol ratio. Compared to the pure ingredients, the obtained powders have an improved release rate, which is about 3 times faster in both cases.

(1) Background: The aim of this study is to investigate the diagnostic-therapeutic problem of pelvic recurrence of rectum cancer, highlighting current surgical standards and the possible role of the minimally invasive approach. This retrospective analysis of our surgical case study wishes to enter this debate while suggesting a possible line of action, based on the site of recurrence; (2) Methods: We examined, retrospectively, all the patients diagnosed, between 2008 and 2018, with cancer of the rectum at the "Pietro Valdoni" Department of Surgery and monitored their follow-up for 5 years. The sample consisted of 368 patients with rectal neoplasm, 136 females and 232 males, with an average age of 65.8 (ranging from 37 to 86); (3) Results: In 103 of the cases, the neoplasm was located in the upper rectum (28%), in 119 cases in the middle rectum (32.3%), in 102 cases in the lower rectum (27.7%), in 31 cases (8.4%) at the level of the right/sigma junction and in 13 cases it was not possible to define the site with certainty (3.5%); (4) Conclusions: The discussion re-mains open as to which approach is best at surgical level, whether laparoscopic, robotic or open-air. Our experience informs us that the most dangerous site remains on the anastomotic site.

Controlled drainage (CD) is an important agricultural measure for maintaining soil moisture and nutrients, controlling groundwater level, and increasing crop yield. In arid regions, CD can be used to improve the water supply in agriculture and reduce environmental pollution. In this study, we investigated the effect of CD, including a drainage depth of 40 cm (CWT1) and 70 cm (CWT2) during the plant growth period, free drainage (FD), and open ditch drainage (OD) on the migration of water, nutrients, and salts in the soil; the dynamics of groundwater level; the loss of soil nitrogen; and the growth of oilseed sunflower plants. Compared with FD, CD increased the water and nutrient content in the soil, reduced nitrogen loss, and enhanced the ability of the soil to continuously supply nitrogen to the oilseed sunflower plants, which benefited plant growth at later growth stages and reduced environmental pollution. During the period between irrigation at the budding stage and harvest stage, the average soil water content in the 0–20 cm soil layer in CWT1 increased by 3.67%, 4.78%, and 0.55%, respectively, compared with that in CWT2, FD, and OD. The soil mineral content in CWT1 was 25.17%, 35.05%, and 17.78% higher than that in CWT2, FD, and OD, respectively, indicating that higher soil salinity occurred at the later stage of plant growth in CWT1, which actually had little effect on the plants due to their enhanced salt tolerance and increased need for water and nutrients at that stage. In addition, CD delayed the decline in groundwater level, which allowed the plants to use groundwater at later growth stages, and as a result the yield and water use efficiency were improved. CWT1 significantly increased oilseed sunflower yield by 4.52–11.14% and increased water use efficiency by 1.16–10.8%. Moreover, CWT1 also increased the survival rate of the oilseed sunflower plants by 2.62–2.92%, and the plants demonstrated good growth. Therefore, under CD conditions, plants used soil water and nitrogen more efficiently and, as a result, their productivity was increased, and the water quality was improved.

Background: New regional techniques can improve pain management after nephrectomy. Methods: This study was a randomized controlled trial conducted at two teaching hospitals. Patients undergoing elective open and laparoscopic nephrectomy were eligible to participate in the trial. A total of 100 patients were divided into a quadratus lumborum block (QLB) group and a control (CON) group. At the end of surgery, but while still under general anesthesia, unilateral QLB with ropivacaine was performed on the side of nephrectomy for patients in the QLB group. The main measured outcome of this study was oxycodone consumption via a patient-controlled anesthesia (PCA) pump during the first 24 hours following surgery; other measured outcomes included postoperative pain intensity assessment, patient satisfaction with pain management, and persistent pain evaluation. Results: Patients undergoing QLB needed less oxycodone than those in the CON group (34.5 mg [interquartile range 23–40 mg] vs. 47.5 mg [35–50 mg]; p<0.001). No difference between the groups was seen in postoperative pain intensity measured on the visual analog scale, except for the evaluation at hour 2, which was in favor of the QLB group (p=0.03). Patients who received QLB were more satisfied with postoperative pain management than the CON group. Persistent postoperative pain was assessed with the Neuropathic Pain Symptom Inventory (NPSI) at months 1, 3, and 6 and was found to be significantly lower in the QLB group at each evaluation (p<0.001). We also analyzed the impact of the surgery type on persistent pain severity, which was significantly lower after laparoscopic procedures than open procedures at months 1, 3, and 6. Conclusions: QLB reduces oxycodone consumption in patients undergoing open and laparoscopic nephrectomy and decreases persistent pain severity months after hospital discharge.

A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.