Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

In contrast to the traditional fillers, clay, in particular, natural smectite clay represents an environmentally significant alternative to improve the properties of polymers. Compared to con-ventional nanofillers, smectite clay can effectively enhance the physical and mechanical properties of polymer nanocomposites with a relatively small amount of addition (< 5 wt%). The present study focuses on investigating the reinforcing efficiency of different amounts (up to 5 wt%) of a natural Brazilian smectite clay on the mechanical and thermal properties of poly(butylene terephthalate) (PBT) nanocomposites. Natural Brazilian clay modified by addition of quaternary salt and sodium carbonate (MBClay) was infused into the PBT polymer by melt extrusion, using a twin-screw extruder. It was found that the best properties for PBT were obtained at 3.7 wt% of modified BClay. Tensile strength at break exhibited an increase of about 60 %, flexural strength increased by 24 % and flexural modulus increased by 17 %. In addition, an increase in the crystallinity percentage of PBT/BClay nanocomposite was confirmed by DSC and XRD analysis, and a gain of about 45 % in HDT was successfully achieved due to incorporation of 3.7 wt% of MBClay.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

The interaction of solution of poly (diallyldimethylammonium) chloride, PDADMAc and sodium dodecylsulfate, SDS has been studied using conductometric, densimeter and zeta potential methods. the critical micellization concentration (cmc) was determinated with conductance results and increased with the addition of PDADMAc comparing with solutions containing pure SDS. Further the degree of dissociation,  and thermodynamic parameters viz. free energy of micellization, and entropy of micellization, has been evaluated. there results demonstrated that surfactant/polymer complex is governed by both electrostatic and hydrophobic interactions. The apparent molar volume, Vϕ and adiabatic compressibility, Kϕ;s have been determined for the SDS solution from density and speed sound data. the negative charge of the SDS solutions with polymer shows that these complexes probably do not contain surfactant in the form of micelles.

In this paper, first the Self-Written Waveguide (SWW) process in wet photopolymer media (liquid solutions), are examined for three examples: single-, counter-, and co-fibers exposure. Then the SWWs formed inside solid material are examined including the effects of manipulating the alignment of the fibers. In all cases high precision measurements are used to position the fiber optic cables (FOCs) before exposure using a microscope. The self-writing process is indirectly monitored by observing (imaging) the light emerging from the side of the material sample during SWW formation. In this way the optical waveguide trajectories formed in an Acrylamide/Polyvinyl Alcohol (AA/PVA) a photopolymer material (sensitized at 532 nm) are examined. First the transmission of light by this material is characterized. Then the bending and merging of the waveguides which occur are investigated. The predictions of our model are shown to qualitatively agree with the observed trajectories. The largest index changes taking place at any time during the exposure, i.e. during SWW formation, are shown to take place at the positions where the largest exposure light intensity is present. Typically, such maxima exist close to the input face and the first maximum is referred to as the location of the Primary Eye. Other local maxima also appear further along the SWW and are referred to as Secondary Eyes, i.e. deeper within the material.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

The rapid, sensitive, and selective detection of pathogenic bacteria is of utmost importance in ensuring food safety and preventing the spread of infectious diseases. Here, we present a novel, reusable, and cost-effective impedimetric sensor based on a dual bacteria-imprinted polymer (DBIP) for the specific detection of Escherichia coli O157:H7 and Staphylococcus aureus. The DBIP sensor stands out with its remarkably short fabrication time of just 20 minutes, achieved through the efficient electro-polymerization of o-phenylenediamine monomer in the presence of dual bacterial templates, followed by in-situ template removal. The key structural feature of the DBIP sensor lies in the cavity-free imprinting sites, indicative of a thin layer of bacterial surface imprinting. This facilitates rapid rebinding of the target bacteria within a mere 15 minutes, while the sensing interface regenerates in just 10 minutes, enhancing the sensor's overall efficiency. A notable advantage of the DBIP sensor is its exceptional selectivity, capable of distinguishing the target bacteria from closely related bacterial strains, including different serotypes. Moreover, the sensor exhibits high sensitivity, showcasing a low detection limit of approximately 9 CFU mL-1. The sensor's reusability further enhances its cost-effectiveness, reducing the need for frequent sensor replacements. The practicality of the DBIP sensor was demonstrated in the analysis of real apple juice samples, yielding good recoveries. The integration of quick fabrication, high selectivity, rapid response, sensitivity, and reusability makes the DBIP sensor a promising solution for monitoring pathogenic bacteria, playing a crucial role in ensuring food safety and safeguarding public health.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

Block copolymers are a class of materials particularly interesting for their ability to self-assemble into ordered structures. In this context, the coupling between environment and dynamics is particularly relevant, given that movements at the molecular level influence various properties of macromolecules. Mixing the polymer with a second macromolecule appears to be an easy way to study these relationships. In this work, we studied a system based on two diblock copolymers of methyl methacrylate as first block and 3-methyl-4-[6-(methylacryloyloxy)-hexyloxy]-4’-pentyloxy azobenzene as second block and their blends with PMMA. The relaxational properties of these systems were investigated by electron spin resonance (ESR) spectroscopy sensitive to nanometric length-scales. The results of the study on the blends were related to the dynamic behavior of the copolymer. The study evidenced the presence of fast and slow molecular sites for the molecular reorientation at nanoscale, modulated by the ability of block copolymer to form supramolecular structures. For blends, the heterogeneities at nanoscale are still detected. However it was found that the presence of the PMMA as the major component of the blends modified their dynamic behaviour.

Considering the safety issues of Li ion batteries, all-solid-state polymer electrolyte has been one of the promising solutions. In this point, achieving a Li ion conductivity in the solid state electrolytes comparable to liquid electrolytes (>1 mS/cm) is particularly challenging. Employment of polyethylene oxide (PEO) solid electrolyte has not been not enough in this point due to high crystallinity. In this study, hybrid solid electrolyte (HSE) systems are designed with Li_1.3Al_0.3Ti_0.7(PO₄)₃(LATP), PEO and Lithium hexafluorophosphate (LiPF₆) or Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). Hybrid solid cathode (HSC) is also designed using LATP, PEO and lithium cobalt oxide (LiCoO₂, LCO)—lithium manganese oxide (LiMn₂O₄, LMO). The designed HSE system displays 3.0 × 10⁻⁴ S/cm (55 ℃) and 1.8 × 10⁻³ S/cm (23 ℃) with an electrochemical stability as of 6.0 V without any separation layer introduction. Li metal (anode)/HSE/HSC cell in this study displays initial charge capacity as of 123.4/102.7 mAh/g (55 ℃) and 73/57 mAh/g (25 °C). To these systems, Succinonitrile (SN) has been incorporated as a plasticizer for practical secondary Li ion battery system development to enhance ionic conductivity. The incorporated SN effectively increases the ionic conductivity without any leakage and short-circuits even under broken cell condition. The developed system also overcomes the typical disadvantages of internal resistance induced by Ti ion reduction. In this study, optimized ionic conductivity and low internal resistance inside the Li ion battery cell have been obtained, which suggests a new possibility in the secondary Li ion battery development.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

Reactions of N‚N'-bis(3-methylpyridyl)oxalamide (L1), N,N’-bis(3-methylpyridyl)adipoamide (L2) and N,N’-bis(3-methylpyridyl)sebacoamide (L3) with tricarboxylic acids and Cu(II) salts afforded {[Cu(L1)(1,3,5-HBTC)]·H2O}n (1,3,5-H3BTC = 1,3,5-benzenetricarboxylic acid), 1, {[Cu1.5(L2)1.5(1,3,5-BTC)(H2O)2]·6.5H2O}n, 2, [Cu(L2)0.5(1,3,5-HBTB)]n (1,3,5-H3BTB = 1,3,5-tri(4-carboxyphenyl)benzene), 3, [Cu4(L3)(OH)2(1,3,5-BTC)2]n, 4, {[Cu3(L3)2(1,3,5-BTB)2]·2.5MeOH·2H2O}n, 5, and {[Cu3(L3)2(1,3,5-BTB)2 ]·DMF·2H2O}n, 6, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 form a 2D layer with the {44.62}-sql topology, a 2D layer with the (4.62)2(42.62.82)-bex topology, a 3-fold interpenetrated 3D net with the (412.63)-pcu topology and a 3D framework with the (410.632.83)(42.6)2(43.63) topology, respectively, whereas 5 and 6 are 3D frameworks with the (63)2(64.82)(68.85.102) topology. Complex 5 shows a better iodine-adsorption factor of 290.0 mg g-1 at 60 oC for 360 minutes than the other ones, revealing that the flexibility of the spacer ligand governs the structural diversity and the adsorption capacity.

The conducted investigation encompassed the comprehensive integration of mechanical, envi-ronmental, chemical, and microstructural evaluations of a composite amalgamating sandy soil and a synthetic polymer at two distinct concentrations (2.5% and %) across multiple curing in-tervals (0, 1, 2, 4, 7, 15, 30, and 45 days). The studied soil originates from an environmentally sig-nificant protected area in Brazil. The implementation of mechanisms for soil improvement in the region must adhere to technical criteria without causing environmental harm. Direct shear testing was conducted, permeability was assessed, and microstructure analysis and XRD and XRF/EDX studies of both the soil and composites were conducted. It was observed that longer curing times yielded improved results in shear stress, friction angle, and cohesive intercept, with SP_5% exhibiting the highest values compared to the soil and SP_2.5%. Adding the polymeric so-lution to the soil contributed to cementation and cohesion gains in the substrate. Through mi-crostructural characterization, the polymer's role as a cementing agent for the grains is evident, forming a film on the grains and binding them together. Based on the analyses and studies con-ducted in the research, it can be concluded that there is technical feasibility for applying the pol-ymeric solution at both dosages in geotechnical projects.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

The main purpose of this work is to contribute to understanding the mechanism of oxidation of the polymeric components of common disposable masks used during the COVID-19 pandemic to offer the chemical basis to predict their long-term behaviour under typical environmental conditions. Artificial ageing of representative mask layers under isothermal conditions (110℃) or accelerated photoageing showed that all the PP-made components underwent a fast oxidation process, following the typical hydrocarbon oxidation mechanism. In particular, yellowing and the melting temperature drop are early indicators of their diffusion-limited oxidation. Morphology changes also induced a loss of mechanical properties, observable as embrittlement of the fabric fibres. Results were validated through preliminary outdoor ageing of masks, which allows us to predict they will suffer fast and extensive oxidation only in the case of contemporary exposure to sunlight and relatively high environmental temperature, leading to their extensive breakdown in the form of microfiber fragments, i.e., microplastics.

: We report on a direct correlation between macroscale structural variations and the gas sorption capacities of an ion gel. Here, we chose 1-ethyl-3-methylimidazolium bis(trifluoromethyl sulfonyl)imide ([Emim][TF2N]) and poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) as the ionic liquid and host polymer, respectively. The CO2 sorption in the thin films of IL-polymer was measured by the gravimetric method. The results of our experiment show that the trend of CO2 uptake of these mixtures is non-linearly correlated with the content of IL. Here we highlight the variation in the molecular structure of the polymers is the main reason behind the observed trend. The presented data suggest the possibility of using the composition of mixtures containing IL and polymers to realize a synergistic gain for gas sorption in these mixtures.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

The coexistence of ferroelectric and magnetic order parameters in multiferroic materials opens up a host of new collective properties. In particular, the magnetoelectric (ME) effect namely the induction of electric polarization by a magnetic field or magnetization by an electric field has been widely studied in multiferroics. PVDF is a ferroelectric polymer that has attracted considerable research interest for sensing applications. Compared to traditional ceramic composites, the polymer-ceramic nanocomposites offer inherent advantages, including easy processing, mechanical flexibility and the ability to be moulded into complicated configurations for advanced devices with reduced volume and weight. Additionally, polymer composites generally exhibit superior ME coefficients, attributable to the improved displacement transfer capability of the flexible polymer matrix. In this report, free-standing, flexible and lightweight polymer–ceramic nanocomposite thin films with a fixed weight percentage of ferromagnetic CoFe2O4 nanoparticles have been fabricated using a solution casting technique. The structural, microstructural, and electrical properties of the composite have been characterized by standard experimental techniques. The structural and chemical analyses prove a homogeneous dispersion of the fillers in the microstructure of the composite. The electrical response investigated by impedance spectroscopy reveals the contributions of grains and grain boundaries to the whole impedance of the composites. The ac conductivity as a function of frequency obeys Jonscher’s power law. The improved magnetoelectric properties suggest promising applications in multifunctional devices, including field sensor applications.

The electromagnetic inference is an issue from decades, where working for a better shielding material is still on-going. The purpose of this study is to review the existing methods in the formation of graphene, metal and polymer-based composites. Study indicates that in graphene and metal-based composites, the utilization of alternating deposition method showed the highest shielding effectiveness, whereas, in polymer-based composite, the utilization of chemical vapor deposition method showed highest shielding effectiveness. However, this review reveals that still there is a gap in the literature in terms of the selection of the method. Although there are various available methods which researchers adopt as per their convenience, none of the studies makes a comparison of the methods to form a similar composite. Therefore, as a future gap researcher needs to adopt various methods to form a single composite and then make a comparison of shielding effectiveness. This act will be useful for future researchers to select the appropriate method.

The technological development of piezoelectric materials is crucial for developing wearable and flexible electromechanical devices. There are many inorganic materials with piezoelectric effects, such as piezoelectric ceramics, aluminum nitride, and zinc oxide. They all have very high piezoelectric coefficients and large piezoelectric response ranges. The characteristics of high hardness and low tenacity make inorganic piezoelectric materials unsuitable for flexible devices that require frequent bending. Polyvinylidene fluoride (PVDF) and its derivatives are the most popular materials used in flexible electromechanical devices in recent years and have high flexibility, high sensitivity, high ductility, and a certain piezoelectric coefficient. Owing to increasing the piezoelectric coefficient of PVDF, researchers are committed to optimizing PVDF materials and enhancing their polarity by a series of means to further improve their mechanical–electrical conversion efficiency. This paper reviews the latest PVDF-related optimization materials, related processing and polarization methods, and the applications of these materials such as those in wearable functional devices, chemical sensors, biosensors, and flexible actuator devices for flexible micro-electromechanical devices. We also discuss the challenges of wearable devices based on flexible piezoelectric polymer, consider where further practical applications could be.

Two region asymmetric polymers PR2F and PR1F with three repeat units of A-D-A, π-D-A, and π-D-π along the polymer backbone were attained by polymerizing different fluorinated benzothiadiazole-thiophene units, FBT-T and 2FBT-T units (A–π), with benzodithiophene unit (D), respectively. Here, the new region asymmetric polymers were in contrast to the traditional polymers featuring a D–A or D–π–A–π backbone. Both the region asymmetric polymers showed a low lying of HOMO energy level in relation to that of the PC61BM acceptor and then obtained the high open-circuit voltage of ~1 V in both PR2F and PR1F devices. Bulk-heterojunction devices based on PR2F with difluorinated BT exhibited an appreciable power conversion efficiency (PCE) of 4.73% due to the relatively high and balanced charge carrier mobilities, while the mono-fluorinated BT polymer PR1F-based devices gave a lower PCE of 2.92%. These results indicate that the region asymmetric conjugated polymer is a promising class of materials for polymer solar cell applications, and it is significant to further understand the influence of polymer structure on optoelectronic properties.

The synthesis these past few years of novel organic molecules that spontaneously self-assemble into a large variety of molecular architecture, particularly generating organogels, has opened up new horizons for preparing functional materials. Here, we present an original preparation path of such materials through the making of hybrid gels of these molecules together with covalent polymers. Three types of systems are described: i) intermingled gels where a polymer gel and an organogel pervade one another; ii) encapsulation of self-assembled filaments in polymer fibrils, which provides a system with unusual magnetic properties; iii) the reverse situation where self-assembled nanotubes sheathe polymer fibrils. Here two covalent polymers are considered: a neutral polymer, namely stereoregular polystyrene (isotactic or syndiotactic), and a semi-conducting polymer, P3BT. In the latter case, semi-conducting nanowires are obtained.

The global polyvinyldene flouride market is estimated to reach $937,278.5 thousand by 2019, therefore to develop new membranes and gain pioneering ideas, which could create innovative business opportunities, a fundamental knowledge about membrane properties fabricated from recent commercially available PVDF polymers is highly mandatory. In this study, we successfully prepared nine non-woven supported PVDF membranes using a phase inversion precipitation method starting from a 15 wt% PVDF solution in N-methyl-2-pyrrolidone. Various membrane morphologies were obtained by using (1) PVDF polymers with diverse molecular weight in a range from 300.000 Da to 700.000 Da and (2) different temperatures of the coagulation bath (20, 40, and 60 ±2°C) used for the films precipitation. Environmental Scanning Electron Microscope (ESEM) was used for surface and cross-section morphologies characterization. Atomic Force Microscope (AFM) was employed to investigate surface roughness, while Contact Angle (CA) instrument was used for membranes wettability studies. Fourier Transform Infrared Spectroscopy (FTIR) results show that the fabricated membranes are formed by a mixture of TGTG’ chains in α phase crystalline domains and all-TTTT trans planar zigzag chains characteristic to β phase. Moreover, generated results indicate that the phases content and membrane morphologies depend on the polymer molecular weight and conditions used for the membranes preparation. The diversity of fabricated membranes could be applied by the End User Industries for different applications.

Carbon nanotube (CNT) yarns are fiber-like materials that exhibit excellent mechanical, electrical and thermal properties. More importantly, they exhibit a piezoresistive response that can be tapped for sensing purposes. The objective of this study is to determine experimentally the piezoresistive response of CNT yarns that are embedded in a polymeric medium while subjected to either compression or tension, and compare it with that of the free or unconstrained CNT yarns. The rationale for this study is the need to know the response of the CNT yarn while in a medium, which provides a lateral constraint to the CNT yarn thus mimicking the response of integrated CNT yarn sensors. The experimental program will include the fabrication of samples and their electromechanical characterization. The CNT yarns are integrated in polymeric beams and subjected to four-point bending, allowing the determination of their response under tension and compression. The electrical resistance data from an Inductance-Capacitance-Resistance (LCR) device is used with the data acquired from the mechanical testing system to determine the piezoresistive response of the CNT yarns. This data and information will be used for future modeling efforts and to study the phenomena that occur when CNT yarns are integrated in polymeric and composite materials and structures.

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

Theoretical and experimental approaches have been applied to study the polymer physics under-lying compaction of DNA in the bacterial nucleoid. Knowledge of the compaction mechanism is necessary to obtain a mechanistic understanding of the process of segregation of replicating chromosome arms (replichores) during the cell cycle. In the first part of this review light microscope observations are discussed that have demonstrated that the nucleoid has a lower refractive index and thus a lower density than the cytoplasm. A polymer-physical explanation for this phenomenon was given by the theory of Theo Odijk pro-posed in 1998. By assuming a phase separation between nucleoid and cytoplasm and by imposing equality of osmotic pressure and chemical potential between the two phases, a minimal energy situation is obtained in which soluble proteins are depleted from the nucleoid, thus explaining its lower density. The theory is compared with recent views for DNA compaction that are based on mere exclusion of polyribosomes from the nucleoid or on the transcriptional activity of the cell. These new views raise the question of whether they can still explain the lower refractive index or density of the nucleoid. In the second part of this review the question is discussed how DNA segregation occurs in Esche-richia coli, in the absence of the so-called active ParABS system, present in the majority of bacteria. How is entanglement prevented of nascent chromosome arms, generated at the origin in the pa-rental network of the E. coli nucleoid? The observations of the groups of Sherratt and Hansen in 2006, that the four nascent chromosome arms synthesized in the initial replication bubble, segre-gate to opposite halves of the sister nucleoids implies that extensive intermingling of daughter strands does not occur. Based on the hypothesis that leading and lagging replichores synthesized in the replication bubble, fold into micro-domains that do not intermingle, a passive "four-excluding-arms model" for segregation is proposed. This model implies that the key for seg-regation already lies in the structure of the replication bubble at the very start of DNA replication; it explains the different patterns of chromosome arms as well as the segregation distances between replicated loci as experimentally observed.

The anode of a microbial fuel cell (MFC) was formed on a graphite electrode and immobilized Gluconobacter oxydans VKM-1280 bacterial cells. Immobilization was performed in chitosan, poly(vinyl alcohol) or N-vinylpyrrolidone-modified poly(vinyl alcohol). Ethanol was used as substrate. The anode was modified using multiwalled carbon nanotubes. The aim of the modification was to create a conductive network between cell lipid membranes, containing exposed PQQ-dependent alcoholdehydrogenases, and the electrode to facilitate electron transfer in the system. The bioelectrochemical characteristics of modified anodes at various cell/polymer ratios were assessed via current density, power density, polarization curves and impedance spectres. MFCs based on chitosan at a matrix/cell volume ratio of 5:1 produced maximal power characteristics of the system (8.3 μW/cm2) at a minimal resistance (1111 Ohm cm2). Modification of the anode by multiwalled carbon nanotubes led to a slight decrease of internal resistance (down to 1078 Ohm cm2) and to an increase of generated power density up to 10.6 μW/cm2. We explored the possibility of accumulating electric energy from an MFC on a 6,800-μF capacitor via a boost converter. Generated voltage was increased from 0.3 V up to 3.2 V. Accumulated energy was used to power a Clark-type biosensor and a bluetooth transmitter with three sensors, a miniature electric motor and a light-emitting diode.

Water electrolysis provides efficient and cost-effective production of hydrogen from renewable energy. Currently, the oxidation half-cell reaction relies on noble-metal catalysts, impeding widespread application. In order to adopt water electrolyzers as the main hydrogen production systems, it is critical to develop inexpensive and earth-abundant catalysts. This review discusses the proton exchange membrane (PEM) water electrolysis (WE) and the progress in replacing the noble-metal catalysts with earth-abundant ones. Researchers within this field are aiming to improve the efficiency and stability of earth-abundant catalysts (EACs), as well as to discover new ones. The latter is particularly important for the oxygen evolution reaction (OER) under acidic media, where the only stable and efficient catalysts are noble-metal oxides, such as IrO_x and RuO_x. On the other hand, there is significant progress on EACs for the hydrogen evolution reaction (HER) in acidic conditions, but how many of these EACs have been used in PEM WEs and tested under realistic conditions? What is the current status on the development of EACs for the OER? These are the two main questions this review addresses.

Synthetic bone made of calcium phosphate is widely used for the clinical treatment of bone defects caused by trauma and bone tumors. Although synthetic bone is easy to use, its effects are only partial depending on the size and location of the bone defect, and there are many treatment options other than the use of synthetic bone. Various biodegradable polymers that are being considered for use as scaffolds for regenerative medicine are also being considered for use as synthetic bones; however, commercial synthetic bone products with performance comparable to that of calcium phosphate bioceramics have not yet been clinically applied. This review introduces the practice of bone regeneration therapy with synthetic bone and recent research on bone regeneration therapy with biodegradable polymers.

This study aims to comprehensively compare and evaluate the toughening effects of different nanocarbon materials on vinyl ester resin composites. The incorporation of nanocarbon materials has gained significant attention due to their potential to enhance the mechanical properties of polymers. In this research, carbon nanotubes (CNTs), graphene nanoplatelets (GNPs), and carbon nanofibers (CNFs) were chosen as nanocarbon additives. The mechanical properties, including tensile strength, flexural strength, and impact strength, were systematically investigated and compared for each nanocomposite. Additionally, microstructural analysis was conducted using scanning electron microscopy (SEM) to understand the dispersion of nanocarbon materials within the vinyl ester matrix. The results indicated that all three nanocarbon materials contributed to the toughening of the vinyl ester resin, with varying degrees of improvement in mechanical properties. This study provides valuable insights into the selection of nanocarbon additives for enhancing the toughness of vinyl ester resin and offers guidance for designing advanced polymer composites.

Hydrogels prepared from natural polymer have attracted extensive attentions in biomedical fields such as drug delivery, wound healing, and regenerative medicine due to their good biocompatibility, degradability and flexibility. This review outlines the commonly used natural polymer in hydrogel preparation, including cellulose, chitosan, collagen/gelatin, alginate, hyaluronic acid and starch. The polymeric structure and process/synthesis of natural polymers are illustrated, and natural polymer-based hydrogels including the hydrogel formation and properties are elaborated. Subsequently, the biomedical application of hydrogels based on natural polymer in drug delivery, tissue regeneration, wound healing and other biomedical field is summarized. Finally, the future perspectives of natural polymers and hydrogels based on them are discussed. For natural polymer, novel technologies such as enzymatic and biological methods are developed to improve the structural properties and the development of new natural based polymers or natural polymer derivatives with high performance is still very important and challenging. For natural polymer-based hydrogels, novel hydrogel materials, like double-network hydrogel, multifunctional composite hydrogels and hydrogel microrobots are designed to meet the advanced requirements in biomedical application, and new strategies such as dual-crosslinking, microfluidic chip, micropatterning and 3D/4D bioprinting, have been explored to fabricate advanced hydrogel materials with designed properties for biomedical application. Overall, natural polymeric hydrogels have attracted increasing interests in biomedical application, and the development of novel natural polymer-based materials and new strategies/methods for hydrogel fabrication is badly desirable and still challenging.

The aerospace industry demands high-performance materials that can withstand extreme conditions and maintain efficiency in a variety of applications. Bio-inspired polymer coatings have emerged as a promising approach to meet these demands, by drawing inspiration from natural systems to develop new coatings that exhibit enhanced properties, such as self-cleaning, anti-icing, thermal management, and corrosion resistance. In this review, recent developments in the field of bio-inspired polymer coatings for aerospace applications are presented, covering a range of coatings and their respective properties. We discuss the recent developments and applications of bio-inspired coatings, with a focus on their advantages and challenges in aerospace applications. We also highlight the potential for future research and development in this field, including the integration of advanced technologies such as nanotechnology and additive manufacturing. The review aims to provide insights into the current state-of-the-art of bio-inspired polymer coatings for aerospace applications and to inspire further research in this rapidly growing field.

The illicit use of fentanyl has led to hundreds of thousands of opioid-related deaths worldwide. Therefore, the detection of fentanyl by law enforcement and recreational users is of utmost importance. However, current detection methods are expensive, time-consuming, require special storage conditions and necessitate complex instrumentation that is generally unportable and requires skilled personnel to operate. An alternative approach would be using molecularly imprinted polymers (MIPs) as the recognition component of a handheld sensor, testing strip, or color-based assay. In this work, a molecularly imprinted polymer was made by using methacrylic acid (MAA) and ethyleneglycol dimethacrylate (EGDMA) as the functional monomer and cross-linking monomer respectively, and benzylfentanyl (Bfen) as the template. The use of benzylfentanyl is advantageous because it closely resembles the structure of fentanyl but does not have any physiological effects as a narcotic. Important studies herein determined the optimum ratio of the template:functional monomer, with subsequent evaluations of selectivity versus the commonly encountered narcotics such as heroin, cocaine, and methamphetamine. The data obtained from the HPLC analysis showed that the Bfen-MIP was successful in selectively binding the template and actual fentanyl, better than other common narcotics.

A partial least squares (PLS) quantitative chemometric method based on the analysis of the MID-FTIR spectrum of polymer inclusion membranes (PIMs) used for the extraction of Cr(VI) from aqueous media is developed. The system previously optimized considering the variables membrane composition, extraction time, and pH, is characterized in terms of its adsorption isotherm, distribution coefficient, extraction percent and enrichment factor. A Langmuir type adsorption behavior with KL = 21.99 L/mg, qmax = 0.242 mmol/g and 0&lt;RL&lt;1, indicates that metal adsorption is favorable. The characterization of the extraction reaction is performed as well showing an 1:1 Cr(VI):Aliquat 336 ratio, in agreement with solvent extraction data. The principal component analysis (PCA) of the PIMs revels a complex pattern, which is satisfactorily simplified and related to Cr(VI) concentrations through the use of a variable selection method (iPLS) in which bands in the ranges 3451–3500 cm-1 and 3751–3800 cm-1 are chosen. The final PLS model including the 100 wavelengths selected by iPLS and 10 latent variables shows excellent parameter values with RMSEC: 3.73115, RMSECV: 6.82685, Bias: -1.91847e-13, CV Bias: 0.185947, R2 Cal: 0.98145, R2 CV: 0.940902, recovery%: 104.02 ± 4.12 (=0.05), sensitivity%: 0.001547 ppb, γ: 3.8 ppb, γ- 1: 0.6 ppb-1, selectivity: 0.0155, linear range: 5.8–100 ppb, LD: 1.9 ppb, and LQ: 5.8 ppb. The developed PIM sensor is easy to implement as it requires few manipulations and reduced number of chemical compounds in comparison to other similar reported systems.

The disc brake rotors are designed to withstand both, Maximum possible deceleration (emergency braking) and a series of frequent braking cycles. A effective rotor design and superior heat dissipating material provide better performance during the braking mechanism. In this experiment, modified ventilated disk brake rotors are developed with holes and slots and the stress, deformation, heat flux and temperature distribution has been analysed. Designing of the Finite element models of the rotor are created with SolidWorks and simulated using ANSYS. Structural and thermal characteristics are compared with a reference disk brake rotor of the motorcycle (TVS Apache RTR180). It is found that the modified rotors outperform the conventional one in terms of stress generation, temperature distribution and deformation. Furthermore, this Analysis helps us to find out the best suited material for one of the proposed designs. This experiment provides us an insight of the structural and thermal characteristics of the geometrically modified rotor that can be used to upgrade and outperform the current disc brake rotor used in the motorcycle (TVS Apache RTR180).

Hydrogel-based wearable electrochemical biosensors (HWEBs) are emerging biomedical devices that have recently received immense interest. The exceptional properties of HWEBs include excellent biocompatibility with hydrophilic nature, high porosity, tailorable permeability, the capability of reliable and accurate detection of disease biomarkers, suitable device-human interface, facile adjustability, and stimuli-responsive to the nanofiller materials. Although the biomimetic three-dimensional hydrogels can immobilize bioreceptors, such as enzymes and aptamers, without any loss in their activities. However, most HWEBs suffer from low mechanical strength and electrical conductivity. Many studies have been performed on emerging electroactive nanofillers, including biomacromolecules, carbon-based materials, and inorganic and organic nanomaterials, to tackle these issues. Non-conductive hydrogels and even conductive hydrogels may be modified by nanofillers as well as redox species. All these modifications have led to the design and development of efficient nanocomposites as electrochemical biosensors. In this review, both conductive-based and non-conductive-based hydrogels derived from natural and synthetic polymers are systematically reviewed. The main synthesis methods and characterization techniques are addressed. The mechanical properties and electrochemical behavior of HWEBs are discussed in detail. Finally, the prospects and potential applications of HWEBs in biosensing, healthcare monitoring, and clinical diagnostics are highlighted.

The use of carbon nanotubes to improve the mechanical properties of polymers is one of the promising directions in materials science. The addition of single-walled carbon nanotubes (SWCNT) to a polymer results in significant improvement of mechanical, electrical, optical, and structural properties. However, the addition of SWCNTs does not always improve the polymer properties. Also, when a certain content of SWCNTs is exceeded, the mechanical properties of the nanocomposite are getting worse. This article reports the results of computer simulations for predicting the mechanical properties of polymer/single-walled carbon nanotube nanocomposites. The efficiency of reinforcing polymer composites is considered depending on the concentration of carbon nanotubes in the polymer matrix, their size and structure. The elastic moduli of the nanocomposites were predicted using computer simulations for unit cell tension (0.1%). General trends in the mechanical properties of composites with polypropylene, poly (ethyl methacrylate), polystyrene matrices and SWCNTs are shown.

Mucilage from Coccinia grandis was extracted, isolated by maceration technique and precipitated, accordingly. The mucilage was evaluated for its physicochemical, binding, and disintegrant properties in tablets using paracetamol as a model drug. The crucial physicochemical properties such as flow properties, solubility, swelling index, loss on drying, viscosity, pH, microbial load, cytotoxicity were evaluated and the compatibility was analysed using sophisticated instrumental methods (TGA, DTA, DSC, and FTIR). The binding properties of the mucilage were used at three different concentrations and compared with starch and PVP as standard binders. The disintegrant properties of mucilage were used at two different concentrations and compared with standard disintegrants MCCP, SSG, and CCS. The wet granulation technique was used for the preparation of granules and was evaluated for the flow properties. The tablets were punched and evaluated for their hardness, friability, assay, disintegration time, in vitro dissolution profiles. In vitro cytotoxicity study of the mucilage was performed in human embryonic kidney (HEK) cell line using cytotoxic assay by MTT method. The outcome of the study indicated that the mucilage had good performance when compared with starch and PVP. Further, the mucilage acts as a good disintegrant than MCCP, SSG and CCS to paracetamol tablets. Moreover, the in vitro cytotoxicity evaluation results demonstrated that the mucilage is non-cytotoxic to human cells and is safe.

Molecularly imprinted polymers (MIPs) have been widely used in nanomedicine during the last few years. However, their potential is limited by their intrinsic properties resulting, for instance, in lack of control in drug release processes or complex detection for in vivo imaging. Recent attempts in creating hybrid nanomaterials combining MIPs with inorganic nanomaterials succeeded in providing a wide range of new interesting properties suitable for nanomedicine. Through this review, we aim to illustrate how hybrids molecularly imprinted polymers may improve patient care with enhanced imaging, treatments and combination of both.

Shape-memory hydrogels (SMH) are as multifunctional, actively-moving polymers of interest in biomedicine. In loosely crosslinked polymer networks gelatin chains may form triple helices, which can act as temporary netpoints in SMH, depending on the presence of salts. Here, we show programming and initiation of the shape-memory effect of such networks based on a thermomechanical process compatible with the physiological environment. The SMH were synthesized by reaction of glycidylmethacrylated gelatin with OEG α,ω-dithiols of varying crosslinker length and amount. Triple helicalization of gelatin chains is shown directly by wide-angle X-ray scattering and indirectly via the mechanical behavior at different temperatures. The ability to form triple helices increased with the molar mass of the crosslinker. Hydrogels had storage moduli of 0.27-23 kPa and Young’s moduli of 215-360 kPa at 4 °C. The hydrogels were hydrolytically degradable, with full degradation to water soluble products within one week at 37 °C and pH = 7.4. A thermally-induced shape-memory effect is demonstrated in bending as well as in compression tests, in which shape recovery with excellent shape recovery rates Rr close to 100% were observed. In the future, the material presented here could be applied e.g. as self-anchoring devices mechanically resembling the extracellular matrix.

The diffusion process of water molecules within a polyetherimide (PEI) glassy matrix has been analyzed by combining the experimental analysis of water sorption kinetics performed by FTIR spectroscopy with theoretical information gathered from Molecular Dynamics simulations and with the expression of water chemical potential provided by a non-equilibrium lattice fluid model able to describe the thermodynamics of glassy polymers. This approach allowed to construct a convincing description of the diffusion mechanism of water in PEI providing molecular details of the process related to the effects of the cross- and self-hydrogen bondings established in the system on the dynamics of water mass transport.

Hybrid microparticles based on an iron core and amphiphilic shell have been prepared to respond simultaneously to external (magnetic and ultrasounds field) and internal (pH) stimuli for delivery of the anticancer drug doxorubicin. The microparticles have been prepared in three main steps; including surface modification of the iron core followed by conjugation with the amphiphilic chitosan and drug loading. The particles demonstrate spherical shape and dimension in the range 1-3 m with tunable surface charge by changing the pH of surrounding environment. The microparticles demonstrate good stability in simulated physiological solutions and able to allocate up to 400 g of drug per mg of bare carrier. The response to ultrasound and the changes in the shell structure when exposed to different pH allows to control the doxorubicin release. In vitro cytotoxicity tests performed on fibloblast NIH/3T3 demonstrate a reduction in the cell viability when doxorubicin was administrated by microparticles compared to the free formulation; in particular when ultrasound were applied. The bare microparticles demonstrate cytocompatibility and hemocompatibility up to 50g/mL and 60 g/mL, respectively.

Molecularly imprinted polymers (MIPs) can often bind target molecules with high selectivity and specificity. When used as MIPs, conductive polymers may have unique binding capabilities; they often contain aromatic rings, which have a great tendency to undergo covalent and hydrogen bonding interactions with similarly structured target (or template) molecules. In this work, an electrochemical method was used to optimize the synthetic self-assembly of poly(aniline-co-metanilic acid) and testosterone, forming testosterone-imprinted polymers (TIPs) on sensing electrodes. The linear sensing range for testosterone ranged from 0.1 to 100 pg/mL, and the limit of detection was as low as ~pM. Random urine samples were collected and diluted 1000 fold to measure testosterone concentration using the above TIP sensors in comparison with a commercial ARCHITECT ci 8200 system. The testosterone concentrations in the tested samples were in the range of 0.33± 0.09 to 9.13±1.33 ng/mL. The mean accuracy of the TIP-coated sensors was 90.3 ±7.0 %.

The isolation and characterization of chitin (CHI) obtained from Vespa velutina (CHIVV) is described. Moreover, a trapping procedure is presented to selectively catch the invasive species. The chitin contents of dry Vespa velutina was observed to be 11.7 %. The physicochemical properties of CHIVV was characterized by Fourier transform infrared spectroscopy (FTIR), solid-state NMR (ssNMR), elemental analysis (EA), scanning electron microscopy (SEM) and thermogravimetric analysis (TG). Obtained CHIVV is close to pure (43, 47% C, 6.94% H, and 6.85% N) and full acetylated with a value of 95.44%. Also, lifetime and kinetic parameters such as activation E and the frequency factor A using model-free and model-fitting methods, were determined. For CHIVV the solid state mechanism that follows the thermodegradation is of type F2 (Random nucleation around two nuclei). Vespa velutina chitin should not be used at temperatures above 60ºC, since its half-life would be only one year, and from an industrial point of view it would not be profitable. Based on certain factors such as the current and probable continued abundance of Vespa velutina and the quality of the product obtained, the invasive Asian hornet is a promising alternative source of chitin.

Adsorption is an effective strategy for the removal of pollutants from the wastewater. Herein, a 2-hydroxyterephthalic acid (HTC) modified hypercrosslinked polymer (HTC-HCP) is successfully synthesized via Friedel-Crafts reactions, and used as an adsorbent for the different types of pollutants including organic contaminants and heavy metal ions from wastewater. Excellent adsorption capacities are observed for amines (aniline, p-methylaniline (p-MA), p-chloroaniline (p-CA), and p-aminobenzoic acid (p-ABA)), phenols (phenol, p-chlorophenol (4-CP) Bisphenol A (BPA), 1-Naphthol (1-NP)), dyes (rhodamine B (RhB) and methyl orange (MO)), and metal ions (Pb2+, Hg2+, and Cd2+). The resulting polymers exhibited excellent adsorption performance towards these pollutants. Especially, the removal rate of aniline is above 95% in the concentration of 2.5 mg/L in 40 min at 25 °C. The interaction mechanism has been investigated, and confirmed by FTIR and the theoretical calculation results. It is due to surface complexation and chemisorption between adsorbent and adsorbate. The polymer exhibits good performance such as high adsorption capacity, high separation efficiency, biodegradable properties, and easy regeneration, suggesting that its potential technological applications for the removal of organic compounds and heavy metal ions from actual industrial effluent.

Synthesis of poly(o-phenylenediamine) (PoPD) and poly(o-phenylenediamine)-ZnO (PoPD-ZnO) nanocomposites on carbon steel by in-situ polymerization with HCl acid as doping acid Material coating. The composition and structure of PoPD-ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The corrosion protection ability of polymer coatings in 3.5% NaCl was studied by potentiodynamic polarization curves and electrochemical impedance spectroscopy. It can be seen from the electrochemical corrosion experimental data that PoPD-WPU coating (PWC) and PoPD-ZnO-WPU coating (PZWC) can effectively improve the corrosion resistance of the carbon steel substrate, and the corrosion rate is reduced by 2-3 orders of magnitude compared with carbon steel. The conclusion demontrates that PoPD can effectively extend the service life of carbon steel substrates. In addition, it is advantageous to form a compact and low-defect coating when added nano-particle ZnO, which is advantageous for the POPD film to develop its good barrier property and corrosion resistance.

In this study, two donor-acceptor (D-A) type conjugated polymers namely PQSeCz and PQSeFl were designed and synthesized. Selenophene was incorporated as a π -bridge, quinoxaline as an acceptor unit while carbazole and fluorene were used as the donor units. Polymers were synthesized via palladium catalyzed Suzuki polymerization reaction. All molecules were characterized by 1H and 13C NMR Spectroscopy. The weight and number average molecular weights of the two polymers were determined by gel permeation chromatography (GPC). Electrochemical and spectroelectrochemical characterizations of the polymers were performed to investigate their optoelectronic properties. Oxidation potentials were 1.15 V/ 0.82 V and 1.11 V/ 0.82 V for PQSeCz and PQSeFl respectively, while reduction potentials were -1.26 V /-1.14 V and -1.48 V/ -1.23 V, respectively. In the visible region, maximum absorption wavelengths for the two polymers were 551 nm and 560 nm, respectively. Optical band gaps (Egop) were found from the lowest energy π – π∗ transition onsets as 1.71 eV and 1.58 eV, respectively. Both polymers showed good solubility in common solvents.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

A new approach for the preparation of polymer brush was developed via the union of controlled/“living” radical polymerization and click chemistry. The application of the approach realized the more quickly and accurate design and synthesis of the polymer brushes. A novel functional polymer brush of poly(acrylonitrile-g-glycidyl methacrylate) with tremendous application potential in the field of biology has been successfully synthesized via the new approach. The reaction conditions of click chemistry were optimized with the reaction time and the reactant ratio and judged from UV-vis spectra. Under the optimum of click chemistry, the novel functional polymer brushes were prepared. The GPC, FTIR analyses, 1H NMR spectrum and TGA were employed to ensure the successful synthesis of poly(acrylonitrile-g-glycidyl methacrylate) polymer brushes.

This study was conducted to explore the potential of superabsorbent polymers (SAPs) from used disposable diapers as soil moisture conditioner. Swelling behavior of the proposed hydrogel in response to external stimuli such as salt solutions, temperature and pH was studied. In addition, laboratory experiments were carried out to evaluate the effects of incorporation hydrogel on germination of bean (Phaseolus vulgaris L.) and pumpkin (C. pepo) seeds. The structure of the superabsorbent was characterized by Fourier transform infrared spectroscopy (FTIR). The results indicate that the proposed SAP exhibited a maximum swelling capacity of 189 g.g-1 of dry gel. It was observed that the swelling capacity decreased with an increase in the ionic strength of the swelling medium. When this SAP was mixed with sandy soil, the mixture was able to lose water more slowly. The seeds germination and seedling growth was remarkably influenced by the application of 0.5, 1.0 and 2.0 w/w% of SAP compared to the untreated soil. Therefore, it follows that it is possible to take advantage of SAPs property from used disposable diapers to retain the moisture in soil as an alternative to value the use of such waste, showing that it has potential for diverse applications in agriculture.

Electrical properties of the thin films of poly(arylene ether ketone) copolymers (co-PAEKs) with the fraction of phthalide-containing units of 3, 5 and 50 mol% in the main chain were investigated by using radiation induced conductivity (RIC) measurements. Transient current signals and current-voltage (I-V) characteristics were obtained under exposing 20÷25 thick films of the co-PAEKs to monoenergetic electron pulses of the energy ranged from 3 to 50 keV in the electric field ranged from 5 to 40 V/μm. The Rose-Fowler-Vaisberg semi-empirical model based on a multiple trapping formalism was used for an analysis of the RIC data and the parameters of the highly dispersive charge carrier transport were evaluated. The analysis revealed that charge carriers moved in isolation from each other and the applied electric fields were below the threshold field triggering the switching effect (a reversible high-to-low resistivity transition) in the co-PAEK films. It was also found that the co-PAEK films due to the super-linear I-V characteristics are highly resistant to electrostatic discharges arising from the effects of ionizing radiation. This property is important for the development of protective coatings for electronic devices.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at &lt;2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

In view of the complexity of the pile foundation underpinning structure system and the stringent requirements of the construction process, this paper briefly describes the necessity of introducing epoxy resin reinforcing adhesive of planting rebar in the design of pile foundation underpinning beam structure to im-prove the mechanical properties of the underpinning beam new and old concrete joint surfaces and proposes a new type of pile foundation underpinning beam system construction method by “chiseling + prestressed reinforcement + epoxy resin reinforcing adhesive”. This paper uses an actual pile foundation underpinning project of an urban overpass as a prototype, designs and creates a model structure with a similarity ratio of 1/6, and performs repeated pro-gressive static loading tests to study the load carrying capacity, displacement change, and other properties of the underpinning structure, as well as analyses and distorts the overall working performance and failure mode of them. On this basis, the prototype structure's finite element analysis model was built, and the finite element analysis results were compared with the test results to get the mechanical properties and deformation characters of the actual pile foundation under-pinning structure system corresponding to the actual underpinning beam load. This paper's study can lay the theoretical and experimental foundation for the smooth development of similar projects.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

The growing interest in modern polymer materials targeted the research on complex plastic coatings and the possibilities of modifying their features and properties during manufacturing. Today's modern coatings, including polyurea and polyurethane, are among the most modern developed resins. Compared to other polymer coatings, they are distinguished by their versatility, strength, and durability. They undoubtedly represent the next step in the evolution of coatings. Advances in coating technology have also led to the development of spray, injection, and roto-cast application equipment, improving polyurea-based elastomers’ performance. For many years, there has been much interest in increasing the flame resistance of polymers. This is dictated by safety considerations and the increasing requirements for the flammability of plastics, the area of application of which is growing every year. This text attempts to provide an overview of current research on flame retardant composites. Particular attention was paid to polyurea (PU) and polyurea-based hybrids and the application areas of polyurea coatings. The paper defines flame retardants, discusses how they work, and presents types of flame retardants and the current trends of their usage in the production of plastics.

In this work, a colorimetric indicator based on gold nanoparticles (AuNP) and a biodegradable and eco-friendly polymer (sodium alginate, Alg.), has been developed, for the real-time detection of fish spoilage products. AuNP and colorimetric indicator were characterized by: UV-Vis, FTIR spectroscopies, TGA, DSC, XRD, TEM, and colorimetry. The UV-Vis spectrum and TEM showed the successful synthesis, the spherical shape, and the size of AuNPs. Results indicated color changes of the indicator in packaged fish on day 9 of storage at refrigerated temperature (5ºC). These results showed the successful application of colorimetric indicator in the detection of TVB-N in packaged fish.

Hydrogen is believed to be the principal domain of sustainable energy drive as an alternative to fossil fuels. Unlike the existing standards and knowledge for other fuels, the integrity of sealing and storage materials under the hydrogen environment is not comprehensively studied due to the comparatively new technology and lack of standard laboratory protocols. Typically, storage and polymer materials used as sealing experience degradation and damage in different ways over time in the exposure of hydrogen at different operating conditions, called aging. Improved understanding of the physical and chemical mechanism of degradation due to gaseous hydrogen atmosphere; helps to select and develop the materials best suited to carrier and sealing for respective applications. Damage to materials from aging is inevitable in high-pressure hydrogen gas exposure. This review discusses the mechanism of different categories of aging of storage and sealing materials under the hydrogen environment. Also, the article approaches discussing different laboratory test methods for each type of aging simulation. It covers the limitation of current research on determining material integrity through existing techniques of aging experiments and also explores the latest development. Important improvements are suggested in terms of materials development and testing procedures to meet the existing knowledge in the literature.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

An extensive review of literature simulations of polymer melts is given, considering results that test aspects of the Rouse model in the melt. We focus on the mean-square amplitudes < (X_p(0))^{2} > and time correlation functions < X_p(0) X_p(t) > of the Rouse modes $X_p(t)$. Contrary to the Rouse model: (i) Mean-square Rouse mode amplitudes < (X_p(0))^2> do not scale as sin^{-2}(p \pi/2N), N being the number of beads in the polymer. For small p (say, p <= 3) < (X_p(0))^2> scales with p as p^{-2}$; for larger p it scales as p^{-3}. (ii) Rouse mode time correlation functions < X_p(t) X_p(0) > do not decay with time as exponentials; they instead decay as stretched exponentials exp(-a t^b)$. b depends on p, typically with a minimum near N/2 or N/4. (iii) Polymer bead displacements are not described by independent Gaussian random processes. (iv) For p not equal to q, < X_p(t) X_{q}(0) > is sometimes non-zero. (v) The response of a polymer coil to a shear flow is a rotation, not the affine deformation predicted by Rouse. Simulations thus conclusively demonstrate that the Rouse model is invalid in polymer melts. We also briefly consider the Kirkwood-Riseman polymer model.

β-cyclodextrin-based star polymers have attracted much interest because of their unique structures and potential biomedical and biological applications. Herein, we synthesized well-defined folic acid (FA)-conjugated and disulfide bond-linked star polymer ((FA-Dex-SS)-βCD-(PCL)14) acted as theranostic nanoparticles for tumor-targeted magnetic resonance imaging (MRI) and chemotherapy. Theranostic nanoparticles were obtained by loading doxorubicin (DOX) and superparamagnetic iron oxide particles (SPIO) were loaded into the star polymer nanoparticles to obtain ((FA-Dex-SS)-βCD-(PCL)14@DOX/SPIO) theranostic nanoparticles. In vitro drug release studies showed that approximately 100% of the DOX was released from disulfide bond-linked theranostic nanoparticles within 24 h under a reducing environment in the presence of 10.0 mM GSH. DOX and SPIO could be delivered into HepG2 cells efficiently, owing to folate receptor-mediated endocytosis process of the nanoparticles and GSH triggered disulfide-bonds cleaving.Moreover, (FA-Dex-SS)-βCD-(PCL)14@DOX/SPIO showed strong MRI contrast enhancement properties. In conclusion, folate-decorated reduction-sensitive star polymeric nanoparticles are a potential theranostic nanoparticle candidate for tumor-targeted MRI and chemotherapy.

The SiBOC precursor ceramics were fabricated by polymer-derived method SiBOC precursors with different B/Si molar ratios were synthesized by controlling monomer content. The effects of different process conditions on SiBOC ceramics and the oxidation resistance of SiBOC ceramics at a high temperature (1400 ℃) were studied. The SiBOC precursor’s bonds of Si-O-C, Si-O-Si, and Si-O-B were detected by FTIR. The precursor is converted to a rigid ceramic material that has an 85.3 wt % ceramic yield of SiBOC ceramics with B/Si=0.4 by TG-DSC. The results of SEM analysis show that the SiBOC ceramics surface bulges and folds increase with the increase of boric acid content. With the increase of pyrolysis temperature and pyrolysis time, the size and number of pores on the surface of SiBOC ceramics also increase. Static oxidation tests show that SiBOC ceramics with B/Si=0.4 have better oxidation resistance under other conditions being the same.

The aims of this work were to examine the new electrode, based on polymer bacteria modified aluminum electrode for simultaneous production of electricity and degradation of phenol. This electrode is based aluminum modified by bacteria inserted in the polymer matrix, developed in situ on the surface. This electrode, designated subsequently by bacteria-polymer-aluminum, Showed stable response and was characterized with voltametric methods, as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The experimental results revealed that the prepared electrode could be a feasible for degradation of hazardous phenol pollutants. The sensor was successfully applied to the determination of phenol in a real sample with satisfactory results.

Electrospinning polymer fibers for is a well-understood process, primarily resulting in random mats or single strands. More recent systems and methods have allowed for the production of nanofiber yarns (NFY) for ease of use in textiles. This paper presents a method of NFY manufacture using a simplified dry electrospinning system to produce self-assembling functional NFY capable of conducting electrical charge. The polymer is a mixture of cellulose nanocrystals (CNC), polyvinyl acrylate (PVA) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). When treated with Ethylene Glycol (EG) to enhance conductivity, fibers touching the collector plate align to the applied electrostatic field and grow, twisting together as additional nanofiber polymer is added by the jet. The longer the electrospinning continues, the longer and more uniformly twisted the NFY becomes. This process has the added benefit of reducing the electric field required for NFY production from >2.43 kV cm-1 to 1.875 kV cm-1.

In this work, the wetting and evaporation behaviour of non-polar solvent droplets on thin soluble coatings is investigated experimentally. The wetting process on spin coated polymer layers by the solvent is captured using shadowgraphy. Initial spontaneous dynamic wetting as well as later stages of wetting are recorded and evaluated. Furthermore, structures obtained by wetting and subsequent evaporation of solvents on polymer coatings are studied by confocal microscopy. The solubility of the substrate has been varied by using polymers with different molecular masses. We observe that initial spreading dynamics does not depend on the molar mass in the studied range. However, we find a strong influence of the molar mass on the late stage wetting dynamics and on the surface structure after solvent evaporation.

Extensive experimental and theoretical research over the past several decades has culminated in the understanding of the mechanisms behind nanoparticle-mediated enhancements on the mechanical properties of hydrogels. This information is not only crucial to realizing applications that directly benefit from developing hydrogels with high mechanical strength, but also to guide the development of strategies to further enhance hydrogel properties by combining different approaches. In our study, we investigated the effect of combining two approaches – addition of nanoparticles and crosslinking two different polymers (to create double-network hydrogels) – on the mechanical properties of hydrogels. Our studies revealed that these approaches may be combined to synthesize hydrogel composites with enhanced properties; however, both polymers in the double-network hydrogel must strongly interact with the nanoparticles to fully benefit from the addition of nanoparticles. Moreover, the concentration of hydrogel monomers used for the preparation of the double-network hydrogels had a significant effect on the extent of nanoparticle-mediated enhancements; double-network hydrogel nanocomposites prepared using lower monomer concentrations showed higher enhancements in elastic moduli compared to those prepared using high monomer concentrations. Collectively, these results demonstrate that the hypotheses previously developed to understand the role of nanoparticles on the mechanical properties of hydrogel nanocomposites may be extended to double-network hydrogel systems and guide the development of next generation hydrogels with extraordinary mechanical properties through a combination of orthogonal approaches.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

In order to design effective protective coatings against corrosion, the polyvinyl alcohol (PVA) as compound and composite with silver nanoparticles (nAg/PVA) were electrodeposited on copper surface employing electrochemical techniques such as linear potentiometry and cyclic voltammetry. A new paradigm was used to distinguish the features of coatings, i.e., a Deep Convolutional Neural Network (CNN) was implemented to automatically and hierarchically extract the discriminative characteristics from the information given by optical microscopy images. The main arguments that invoke a CNN implementation in the surface science of materials are the following: artificial intelligence techniques can be successfully applied to learn differences between surface coatings; based on their popularity for image processing, CNN can model images related to the problem of coatings; deep learning is able to extract the features that are distinguishable between material surfaces. To provide an overview of the copper surface, CNN was applied on microscope slides (CNN@microscopy) and inherently learnt distinctive characteristics for each class of surface morphology. The material surface morphology controlled by CNN without the interference of the human factor was successfully conducted, in our study, to extract the similarities/differences between unprotected and protected surfaces to establish the PVA and nAg/PVA performance to retard the copper corrosion.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

The possibilities of manufacturing batteries with Nafion 117 membranes in the Na⁺-form intercalated by mixtures of non-aqueous organic solvents used both as electrolyte, separator and binder were investigated. Electrochemical stability of various organic solvent mixtures based on N,N-dimethylacetamide, ethylene carbonate, propylene carbonate, tetrahydrofuran was characterized. It was shown that sodium battery based on Nafion-Na membrane intercalated by mixture of ethylene carbonate ‑ propylene carbonate with Na₃V_1.9Fe_0.1(PO₄)₃/C positive electrode is characterized by a discharge capacity of ca. 110 mAh g^-1 (C/10) at room temperature and shows the ability to cycle for a long time. Batteries with Nafion membrane electrolytes, containing N,N-dimethylacetamide were characterized by capacity fading during cycling, which is due to the interaction of N,N-dimethylacetamide and a negative sodium electrode.

Optimum selectivity of enhanced oil recovery techniques would play a substantial role in the economic prosperity of petroleum industries which might be virtually eliminated unnecessary expenditures. In this paper, the simultaneous utilization of foaming agent, surfactant polymer (SP), and supercritical carbon dioxide were taken into the investigation under the miscible condition to evaluate the efficiency of each scenario on the cumulative recovery factor, water cut and pressure drop. According to the results of this experimental evaluation, SP-foam flooding had witnessed the highest blockage which is caused to have the maximum recovery factor due to the mobilization of more oil volume in the low permeable pores and cracks. Furthermore, the utilization of surfactant with supercritical carbon dioxide had experienced the least recovery factor regarding the insufficient foam generation which is led to less mobilization of oil phase in the pore throats.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

We present results on the spontaneous crystallization of freely-jointed polymers of hard spheres obtained in an unprecedentedly long Monte Carlo (MC) simulation on a system of 54 chains of 1000 monomers. Starting from a purely amorphous configuration and after a transitory dominance of the hexagonal closed packed (HCP) polymorph, the system crystallizes in a final, stable, face centered cubic (FCC) crystal of very high perfection. Through refined metrics we gauge the degree of ordering and identify the regions of the phase transition and the corresponding morphologies. An analysis of chain conformational characteristics, of the spatial distribution of monomers and of the volume accessible to them shows that the phase transition is caused by an increase in translational entropy that is larger than the loss of conformational entropy of the chains in the crystal compared to the amorphous state. Polymer chains in the crystal adopt ideal random walk statistics as their great length renders local conformational details, imposed by the geometry of the FCC crystal, irrelevant.

Recent simulation studies have revealed a wealth of distinct crystal polymorphs encountered in the self-organization of polymer systems driven by entropy or free energy. The present analysis, based on the concept of self-avoiding random walks on crystal lattices, is useful to calculate upper bounds for the entropy difference of the crystals that are formed during polymer crystallization and thus provide predictions on polymorph thermodynamic stability. Here, we compare two pairs of crystals sharing the same coordination number, ncoord: hexagonal close packed (HCP) and face centered cubic (FCC), both having ncoord = 12 and the same packing density, and the less dense hexagonal (HEX) and body centered cubic (BCC) lattices, with ncoord = 8. In both cases, once a critical step length is reached, one of the crystals shows a higher number of SAWs compatible with the crystal. We explain the observed trends in terms of the bending and torsion angles corresponding to the different chain geometry as imposed by the geometric constraints of the crystal lattice.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

Increased CO2 emissions and air pollution impact the environment and human health. In this manner, new functionalized polyaminal-based polymers are synthesized via a one-pot polycondensation reaction of melamine with aldehyde monomers 2-bromo-1-naphthaldehyde and 2-hydroxy-1-naphthaldehyde to yield bromine- hydroxyl- functionalized polymer networks PAN-BrNA and PAN-HNA, respectively. The polyaminals porosity parameters were investigated and applied as an adsorbent for CO2 capture. FTIR, solid-state 13C NMR, and X-ray diffraction verified the PANs structure development. A scanning electron microscope and N2 adsorption-desorption methods were utilized to identify the porous properties of the polymers at 77 K. The Brunauer-Emmett-Teller (BET) surface area of PAN-BrNA and PAN-HNA is (16.6990 m2/g) and (716.7568 m2/g), respectively. At 273 K, PAN-BrNA and PAN-HNA can take CO2 gas up to (4.42786 cm3/g) and (47.55 cm3/g), respectively. The findings show that inserting functional groups has a significant impact on surface area and porosity parameters, as well as CO2 uptake.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

Germanium (Ge) nanostrip is embedded in polymer and studied as a waveguide. Measurement reveals that this new type of semiconductor/polymer heterogeneous waveguide exhibits strong absorption for the TE mode from 1500 nm to 2004 nm, while the propagation loss for the TM mode declines from 20.56 dB/cm at 1500 nm to 4.89 dB/cm at 2004 nm. The transmission characteristics serves as an essential tool to verify the optical parameters (n-κ) of the thin strips, addressing to the ambiguity raised by spectroscopic ellipsometry regarding highly absorbing materials. Furthermore, the observed strong absorption for the TE mode at 2004 nm is well beyond the cut-off wavelength of the crystalline bulk Ge (~1850 nm at room temperature). This redshift is modeled to manifest the narrowing of the Tauc-fitted bandgap due to the grain order effect in the amorphous Ge layer. The accurate measurement of the nanometer-scale light-absorbing strips in a waveguide form is a crucial step toward the accurate design of integrated photonic devices that utilize such components.

As an important organelle in eukaryotic cells, Golgi apparatus is responsible for processing and transporting proteins and lipids in cells. Precise monitoring the status of Golgi apparatus by targeting fluorescence imaging technology is of enormous importance but remains an attractive yet dramatically challenging task. In this study, we report the construction of the first Golgi apparatus targeted sensor with bright near-infrared fluorescence, termed as Golgi-Pdots. As a start point of our investigation, hydrophobic CDs with bright NIR fluorescence at 674 nm (fluorescence quantum yield : 12.18%), narrow emission band of 23 nm, and excellent stability were facilely prepared from Magnolia Denudata flowers through an ultrasonic method. Incorporating the CDs into a polymer matrix modified with Golgi-targeting molecules can produce the water-soluble Golgi-Pdots, which showed high colloidal stability and similar optical properties as compared to CDs. Further studies revealed that the Golgi-Pdots showed good biocompatibility and Golgi-targeting ability. Based on these fascinating properties, Golgi-Pdots have been successfully used for long term bioimaging of Golgi apparatus inside live cells.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

This study aims to theoretically address the design and analysis of an efficient pressure sensor designed by using a polymer-based defective 1D annular photonic crystal (APC). The 1D APC comprises an alternate arrangement of Si and SiO2 in a cylindrical fashion, incorporating a central defect layer. The investigation of the reflectance characteristics of the proposed structure is conducted by separately considering the polystyrene (PS) and the polymethyl methacrylate (PMMA) polymer materials as the defect layer. The pressure-sensitive refractive index of the polymers and the constituent materials of the APC plays a vital role in envisaging the pressure-sensing application. The cornerstone of this study is represented by the shift analysis in the wavelength of the defect mode inside the band gap using different applied pressures by employing the modified transfer matrix method (MTMM). Various geometrical parameters like the defect polymer layer’s thickness and the APC period were carefully optimized to achieve higher sensing performance. The proposed design demonstrated a remarkable pressure sensitivity and FoM of 51.29 nm/GPa and 301.7 GPa-1, respectively, which is considerably high in the current research scenario. It is believed that the proposed structure can be an apt candidate as an innovative high-performance pressure sensor, and it can play a key role in photonic integrated circuits.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

In this study, we report a new epoxy acrylate based shape memory polymer(SMP) fabricated by Liquid crystal display (LCD) Stereolithographic 3D printing. The printed 3D object has a high resolution and high transparency in visible light region. The uniaxial tensile tests showed enhanced tensile toughness and tunable mechanical properties. The fix-recovery and cycle tests indicated high shape recovery properties including high shape recovery rate and excellent cycling stability. In addition, a smart electrical valve actuator was fabricated that can be used in fast heat or electricity responsive electrical circuits. LCD 3D printing provides a low-cost and high efficient way to fabricate fast responsive SMP, which can be used in wide applications in various fields on aerospace engineering, biomedical devices, soft robots and electronic devices.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

We have recently solved the tumbling-snake model for concentrated polymer solutions and entangled melts in the presence of both steady-state and transient shear and uniaxial elongational flows, supplemented by a variable link tension coefficient. Here, we provide the transient and stationary solutions of the tumbling-snake model under biaxial elongation both analytically, for small and large elongation rates, and via Brownian dynamics simulations, for the case of planar elongational flow over a wide range of rates, times, and the model parameters. We show that both the steady-state and transient first planar viscosity predictions are similar to their uniaxial counterparts, in accord with recent experimental data. The second planar viscosity seems to behave in all aspects similarly to the shear viscosity, if shear rate is replaced by elongation rate.

The method for quantitative analysis is based on the direct measurement of the analyte using differential pulse voltammetry (DPV), exploiting its oxidation peak. Calibration curves are set up to evaluate the figures of merit of the analytical method (LOD, LOQ, linear range). The application of the sensor for the dosing of GA in real matrices is carried out by analyzing non-alcoholic and alcoholic beverages and comparing the results with those reported in the literature and with the content of total polyphenols determined by the Folin-Ciocalteu method. In all cases, concentrations of GA align with those previously found in the literature for the beverages examined. Moreover, the values are always lower than the total polyphenols content; this demonstrates the good selectivity of the sensor that can discriminate the target molecule from other polyphenols present.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Traditional methods of non-metallic materials joining for industrial uses are limited to lasers, or induction or conduction heating. The precision and efficiency for large-scale applications are difficult to be achieved at the same time. Here in this paper, we report a precise microwave welding method induced by localized surface plasmon of metallic macro-gaps under microwave excitation. The proposed method utilizes energy from well-developed commercial microwaver, and benefits from the precision of localized surface plasmon, an oscillating electron cloud excited by electromagnetic waves, which is currently under hot investigation only at micro- or nano-scales. The method is applied to the welding of polymers to solve the problems of complex processing equipment and high processing energy consumption in the traditional welding process, so as to cope with the growing energy and environmental crisis. Finite element numerical simulations are used to study the distribution characteristics of electric fields and temperature fields. The results show that the process is a high quality, efficient, low consumption and environmentally friendly green process compared to traditional polymer welding methods.

This study investigates the dynamic characteristics of Natural Rubber (NR)/Polybutadiene Rubber (PBR) based hybrid magnetorheological elastomer (MRE) sandwich composite beams through numerical simulations and finite element analysis, employing Reddy's third-order shear defor-mation theory. Four distinct hybrid MRE sandwich configurations were examined. The validity of finite element simulations was confirmed by comparing them with results from magnetorheo-logical (MR) fluid-based composites. Further, parametric analysis explored the influence of magnetic field intensity, boundary conditions, ply orientation, and core thickness on beam vi-bration responses. Results reveal a notable 10.4% enhancement in natural frequencies in SC4-based beams under a 600mT magnetic field with clamped-free boundary conditions, attributed to in-creased PBR content in MR elastomer cores. However, higher magnetic field intensities result in slight frequency decrements due to filler particle agglomeration. Additionally, augmenting magnetic field intensity and magnetorheological content under clamped-free conditions improves the loss factor by 66% to 136%, presenting promising prospects for advanced applications. This research contributes to a comprehensive understanding of dynamic behavior and performance enhancement in hybrid MRE sandwich composites, holding significant implications for engi-neering applications. Furthermore, this investigation provides valuable insights into the intricate interplay between magnetic field effects, composite architecture, and vibration response.

In this work, we describe the optimization of carbon-based electrodes employed in Bio-Electrochemical Systems (BES) by the deposition on commercial carbon paper electrodes of nanostructured layers of poly(3,4-ethylene-dioxy-thiophene) poly(styrene-sulfonate) (PEDOT:PSS) via Ultrasonic Spray Coating (USC). This innovative application of USC allowed us to demon-strate that uniform and controlled depositions of PEDOT:PSS can be successfully obtained on car-bon-based electrodes. We characterized the morphology and verified the spatial uniformity of depositions via scanning electron microscopy and Raman spectroscopy. Electrochemical charac-terizations on fabricated electrodes demonstrated a more than two-fold increase in electrochemi-cal active surface area with respect to bare carbon paper. A lab-scale experiments on BES was performed selecting Microbial Fuel Cells (MFCs) as the reference devices. Devices featuring USC-deposited PEDOT:PSS electrodes showed a three-fold higher Energy recovery with respect to con-trol cells, reaching a maximum value of (13 ± 2) J·m−3. Furthermore, the optimal PEDOT:PSS con-centration for the MFCs improvement is in line with the values reported in the literature for other deposition methods. In conclusion, this work demonstrates that USC is a promising technique for application in BES.

New advances of nano-enabled weed management: using poly(epsilon-caprolactone)-based nanoherbicides. A review

Nanocomposite hydrogels offer remarkable potential for applications in bone tissue engineering. They are synthesized through the chemical or physical crosslinking of polymers and nanomaterials, allowing for the enhancement of their behaviour by modifying the properties and compositions of the nanomaterials involved. However, their mechanical properties require further enhancement to meet the demands of bone tissue engineering. Here, we present an approach to improve the mechanical properties of nanocomposite hydrogels by incorporating polymer grafted silica nanoparticles into a double network inspired hydrogel (gSNP Gels). The gSNP Gels were synthesised via a graft polymerization process using a redox initiator. gSNP Gels were formed by grafting 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as the first network gel followed by a sequential second network acrylamide (AAm) onto amine functionalized silica nanoparticles (ASNPs). We utilized glucose oxidase (GOx), to create an oxygen-free atmosphere during polymerization resulting in higher polymer conversion compared to argon degassing. The gSNP Gels showed excellent compressive strengths of 13.9 ± 5.5 MPa, a strain of 69.6 ± 6.4%, and a water content of 63.4% ± 1.8. The synthesis technique demonstrates a promising approach to enhance the mechanical properties of hydrogels, which can have significant implications for bone tissue engineering and other soft tissue applications.

In this paper, fiber sensor based on Vernier effect for simultaneous measurement of relative humidity (RH) and temperature is proposed. The sensor is fabricated by coating two kinds of ultraviolet (UV) glue with different refractive indexes (RI) and thicknesses on the end face of a fiber patch cord. Vernier effect is formed by the inner lower-RI polymer cavity and the cavity composed of both polymer films. By calibrating the RH and temperature response of two peaks on the envelope of the reflection spectrum, simultaneous measurement of RH and temperature is realized by solving a set of quadratic equations. Experimental results show that the highest RH and temperature sensitivities of the sensor are 387.3 pm/%RH (in 20%RH to 90%RH) and -533.0 pm/°C (in 15°C to 40°C), respectively. The sensor has merits of low cost, simple fabrication, and high sensitivity, which makes it very attractive for applications that need to simultaneously monitor these two parameters.