Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

Background: Early diagnosis of acute brain injury (ABI) is critical for patients on venoarterial extracorporeal membrane oxygenation (VA-ECMO) to guide anticoagulation strategy; however, neurological assessment in ECMO is often limited by patient sedation. Methods: In this pilot study of adults from June 2018 to May 2019, plasma samples of glial fibrillary acidic protein (GFAP), neurofilament light chain (NFL), and Tau were collected daily after VA-ECMO cannulation and measured using a multiplex platform. Primary outcomes were the occurrence of ABI, assessed clinically, and neurologic outcome, assessed by modified Rankin Scale (mRS). Results: Of 20 consented patients (median age=48.5 years; 55% female), 8 (40%) had ABI and 15 (75%) had unfavorable neurologic outcomes at discharge. 10 (50%) patients were centrally cannulated. The median duration on ECMO was 4.5 days (IQR: 2.5-9.5). Peak GFAP, NFL, and Tau levels were higher in patients with ABI vs. without (AUC = 0.77; 0.85; 0.57, respectively) and in patients with unfavorable vs. favorable neurologic outcomes (AUC = 0.64; 0.59; 0.73, respectively). GFAP elevated first, NFL elevated to the highest degree, and Tau showed limited change regardless of ABI. Conclusion: Plasma biomarkers may facilitate early detection of ABIs in VA-ECMO where neurological exam is limited and assist timely clinical decision-making.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

Polymer adhesives have emerged as a promising dielectric passivation layer in hybrid bonding for 3D integration while they raise misalignment problems during curing. In this work, the synergistic effect of oxygen plasma surface activation and wetting is utilized to achieve bonding between completed cured polyimides. The optimized process achieves a void-less bonding with a maximum shear strength of 35.3 MPa at a low temperature of 250 °C in merely 2 min, significantly shortening the bonding period and decreasing thermal stress. It is found that the plasma activation generated hydrophilic groups on the polyimide surface, and the wetting process further introduced more -OH groups and water molecular on the activated polyimide surface. The synergistic process of plasma activation and wetting facilitate bridging polyimide interfaces to achieve bonding, providing an alternative path for adhesive bonding in 3D integration.

Biostimulation is an animal management practice that helps improve reproductive parameters by modulating animal sensory systems. Chemical signals, mostly known as pheromones, have a great potential in this regard. This study was conducted to determine the influence of short-term female rabbit exposure to different conditions, mainly pheromone-mediated, on reproductive parameters of inseminated does. Groups of 60 females/each were exposed to 1) female urine, 2) male urine, 3) seminal plasma and 4) female-female interaction, just before artificial insemination, and compared to isolated females controls (female-female separated). The following reproductive parameters were analyzed for each group: receptivity (vulvar color), fertility (calving rate), prolificacy and number of born alive and dead kits ⁄ litter. Our results showed that the biostimulation methods employed in this experiment did not significantly improve any of the analyzed parameters. However, female doe exposure to urine, especially to male urine, slightly increased fertility levels when compared to the rest of the experimental conditions. Female-female interaction before artificial insemination, which is a common practice in rabbit farms, did not have any effect, which suggests its removal to avoid unnecessary animal management and time cost. On the other hand, fertility ranges were lower for animals with pale vulvar color whereas no differences were noticed among the other three colours which measure receptivity (pink, red, purple), thus suggesting that these three colours could be grouped together. Additionally, equine chorionic gonadotropin injection could be replaced with various biostimulation methods, therefore reducing or replacing current hormonal treatments, and contributing to animal welfare and to a natural image of animal production.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

Plasma and serum are the most widely used blood-derived biofluids for metabolomics and lipidomics assays, but the isolation of these products from blood may introduce additional bias as indicated by the fact that many analytes that are present at high concentrations in blood cells cannot be measured and evaluated in those samples. Of particular concern, variable hemolysis during the pre-processing of blood products could compromise accurate and reproducible quantification. Compared with plasma or serum, whole blood may be a better alternative due to simplicity of processing. In this study, we provide a comprehensive method for quantification of the whole blood sphingolipidome and the concentrations were compared with those from plasma. Combining a single-phase extraction method with liquid-chromatography high resolution mass spectrometry (R=120, 000), assisted by alkaline hydrolysis, we were able to identify and simultaneously quantify more than 150 sphingolipids. Furthermore, most of sphingolipids remained stable after a freeze/thaw cycle. Whole blood contained a higher concentration of most sphingolipids than corresponding plasma. Moreover, individual variations in the levels of sphingolipids were lower for whole blood than plasma. These findings demonstrate that whole blood could be a better alternative to plasma, and potentially guide the evaluation of sphinglipidome for biomarker discovery.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

Steel products have experienced long-standing problems such as unstable product quality and low product homogeneity. In the continuous casting process, realizing constant temperature pouring is an effective way to improve product homogeneity. Plasma heating can compensate for the temperature drop during casting with a tundish and maintain a stable degree of superheating of the molten steel in the tundish. Plasma heating has a certain impact on the cleanliness of the molten steel and on the tundish covering flux in the tundish while compensating for the temperature drop. This paper uses SEM-EDS, XRD and FactSage to analyze the cleanliness of the molten steel and the characteristics of the tundish covering flux before and after heating. The results show that the number density of inclusions in the tundish is significantly lower after heating, improving the floating removal rate of small-sized inclusions; after heating, the surface morphology of the tundish covering flux sample appears transparent and glassy, with uniform morphology; XRD results show that the tundish covering flux after plasma heating exhibits no crystal precipitation and is amorphous and that there is a certain regularity before and after heating; there are no obvious changes in the composition of the tundish covering flux in the liquid phase area.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li.

Plasma Electrolytic Oxidation (PEO) is a surface treatment, similar to anodizing, that produces thick oxide films on the surface of metals. In the present work, PEO coatings were obtained on zinc-aluminized (ZA) carbon steel using as electrolyte a solution containing sodium silicate and potassium hydroxide, and working with high current densities and short treatment times in DC mode. The surface morphology resulted the typical one of PEO layers, with the presence of a lot of pores and micro-cracks. Considering the cross section, the thickness of the coating was strongly influenced by the process parameters, with different dissolution grades of the ZA layer depending on the current density and treatment time. The PEO layer resulted mainly composed by aluminum and zinc oxides and silicates. The corrosion resistance was remarkable increased in the samples with the PEO coating.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

In this study, diabetogenic effects of long term Ochratoxin A (OTA) administration in rats were investigated and its role in the etiology of diabetes mellitus (DM) was examined utilizing 42 female Wistar rats for these purposes. The rats were divided into 3 different study and control groups according to the duration of the OTA administration. Rats received 45 μg OTA daily in their feed for 6, 9 and 24 weeks study groups. Three control groups without any treatment were also used in the same periods. Blood and pancreatic tissue samples were collected during the necropsy at the end of 6, 9 and 24 weeks. Plasma values of insulin, glucagon and glucose in study and control groups were determined. Pancreatic lesions were evaluated by histopathological examination; then insulin and glucagon expression in these lesions were determined by immunohistochemical methods. Statistically significant decrease in insulin levels in contrast to increases in glucagon and glucose levels in blood were observed. Slight degeneration in Langerhans islet cells were observed at the histopathological examination in all OTA treated groups. Immunohistochemistry of pancreatic tissue revealed decreased insulin and increased glucagon expression. This study demonstrated that OTA may cause pancreatic damage in Langerhans islet and predispose rats to DM.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Alzheimer's disease (AD) is characterized by abnormal amyloid beta (Aβ) plaques and hyperphosphorylated tau in the brain. Aβ plaques precede cognitive impairments and can be detected through amyloid-PET or in cerebrospinal fluid (CSF). Assessing the plasma Aβ42/Aβ40 ratio seems promising for non-invasive and cost-effective detection of brain Aβ accumulation. This approach involves some challenges, including the accuracy of blood-based biomarker measurements and the establishment of clear, standardized thresholds to categorize the risk of developing brain amyloid pathology. Plasma Aβ42/Aβ40 ratio was measured in 277 volunteers without dementia, 70 AD patients and 18 non-AD patients using single-molecule array. Patients (n=88) and some volunteers (n=66) were subject to evaluation of amyloid status by CSF Aβ quantification or PET analysis. Thresholds of plasma Aβ42/Aβ40 ratio were determined based on a Gaussian mixture model, a decision tree, and the Youden index. The 0.0472 threshold, the one with the highest sensitivity, was retained for general population without dementia screening, and the 0.0450 threshold was retained for research and clinical trials recruitment, aiming to minimize the need for CSF or PET analyses to identify amyloid-positive individuals. These findings offer a promising step towards a cost-effective method for identifying individuals at risk of developing AD.

Currently, conventional spark-ignition engines face challenges in meeting the ever-growing demands of customers and increasingly stringent regulations regarding pollutant emissions. A combination of innovative strategies and carbon-neutral fuels is deemed necessary in order to further reduce fuel consumption and minimize engine emissions. The present work aims to assess the performance of combustion strategies using low-carbon content fuel, such as methanol M100, ignited by a plasma-assisted igniter (PAI) under ultra-lean conditions. The experimental campaign is conducted on a single-cylinder research engine at different engine speeds and low loads, moving up to the engine lean stable limits. To determine the benefits brought by the proposed strategy, referred to as M100-PAI, the obtained outcomes are compared with the ones obtained using market gasoline E5 ignited by the PAI system and conventional spark. The synergy between M100 (methanol) and Plasma Assisted Ignition (PAI) in internal combustion engines yielded notable benefits. This combination significantly improved combustion stability if compared to the other combinations tested, by extending the lean stable limit to λ=2.0, reducing cycle-to-cycle variability, and facilitating faster flame front acceleration, resulting in enhanced homogeneity. These enhancements, obtained with the combination M100-PAI, contributed to higher fuel efficiency showing a 10% efficiency gain over the combination E5-gasoline spark ignition.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

The early detection of cognitive decline and timely non-pharmacological management or drug therapy are extremely important in providing care for Parkinson’s disease with dementia (PDD). In this study, we first conducted a discovery study to identify six plasma microRNAs that may allow for the differentiation of PD with or without mild cognitive impairment via NGS. A total of 120 participants were further recruited in a validation cohort and divided into four subgroups, namely, normal controls (HC), PD with no dementia (PDND), PD with mild cognitive impairment (PD-MCI) and PDD. Among the six candidates, miR-203a-3p was successfully detected in the plasma of the validation cohort using droplet digital PCR (ddPCR). Our results show that the ratio of miR-203a-3p/miR-16-5p observed in PDD was significantly increased compared to in PD-MCI (p < 0.001) and PDND (p = 0.041). Moreover, the ratio of miR-203a-3p/miR-16-5p showed a significant correlation with MoCA scores (r = -0.237, p = 0.024) in patients with PD (PwP). The ROC curve of the logistic regression model, consisting of the variables of age, the ratio of miR-203a-3p/miR-16-5p and the UPDRS III score, also demonstrated an average AUC of 0.883 via 5-fold cross-validation. In conclusion, the ratio of miR-203a-3p/miR-16-5p may serve as a potential biomarker for distinguishing cognitive dysfunction from PwP.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Musculoskeletal disorders are increasingly prevalent worldwide, causing significant socioeconomic burdens and diminished quality of life. Notably, patellar chondropathy (PC) is among the most widespread conditions affecting the joint structures, resulting in profound pain and disability. Hyaluronic acid (HA) and platelet-rich plasma (PRP) have emerged as reliable, effective, and minimally invasive alternatives. Continuous research spanning from laboratory settings to clinical applications demonstrate the numerous advantages of both products. These encompass lubrication, anti-inflammation, and stimulation of cellular behaviors linked to proliferation, differentiation, migration, and the release of essential growth factors. Cumulatively, these benefits support the rejuvenation of bone and cartilaginous tissues, which are otherwise compromised due to the prevailing degenerative and inflammatory responses characteristic of tissue damage. While existing literature delves into the physical, mechanical, and biological facets of these products, as well as their commercial variants and distinct clinical uses, there is limited discussion on their interconnected roles. We explore basic science concepts, product variations, and clinical strategies. This comprehensive examination provides physicians with an alternative insight into the pathophysiology of PC as well as biological mechanisms stimulated by both HA and PRP that contribute to tissue restoration.

The effects of co-addition CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases and wear property of plasma beam spraying Fe55-based coatings on 1025 steel were investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDS), ultra-deep field microscope and wet sand rubber wheel friction tester, respectively. The results showed that the dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of microstructure with the co-addition CeO2 and SiC particles. With addition of CeO2 or SiC affected the flowability of molten steel at macro level, leading to a reduction in the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of Fe55 welding layer is Cr7C3, γ-Fe. The grain boundaries consisted mainly of a reticular eutectic structure. The worn-out uniformly surface of the Fe55+1.5 wt% SiC+0.01wt% CeO2 with Ra was 0.28 μm was smoother than that of other samples. The sub-wear mechanisms during the friction process were microploughing and microcutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01wt% CeO2 were well-matched, avoiding excessive microcutting and microplastic deformation.

We presents results obtained from the numerical simulation of the gas-phase chemical kinetics in atmospheric pressure air non-equilibrium plasmas. In particular we have addressed the effect of pulsed operation mode of a planar dielectric barrier discharge. As it was conjectured, the large difference in the time scales involved in the fast dissociation of molecules in plasmas and their subsequent reactions to produce stable chemical species, makes the presence of a continuously repeated plasma production stage unnecessary and a waste of electrical power and efficiency. Results on NOx remediation, ozone production, water vapor and ammonia dissociation are discussed. A few comparisons with experimental findings in a dielectric barrier discharge reactor already used for applications is briefly addressed too. Our results clearly indicate a pattern for the optimization of the discharge using a carefully designed repetition rate and duty-cycle.

The presented work studies the processes of synthesis of nitrogen-containing structures of ZnO using atmospheric pressure microwave nitrogen plasma and investigates their photocatalytic activity in the processes of degradation of 2,4-dinitrophenol and the antibiotic ciprofloxacin when irradiated with sunlight. The work proposes an effective method for formation of photosensitive ZnO powders. Due to the features of plasma treatment in the open atmosphere of zinc metal microparticles, ZnO structures are formed with sizes from hundreds of nanometers to several micrometers with various micromorphologies. High photoactivity was demonstrated (rate constants 0.036 min-1 and 0.051 min-1) of synthesized ZnO structures during photo-degradation of 2,4-dinitrophenol and ciprofloxacin, respectively, when exposed to solar radiation. Photo-active structures of ZnO synthesized using microwave nitrogen plasma can find application in processes of mineralization of toxic organic compounds.

This research focuses on exploring gravitational lensing of the wormhole in Einstein-bumblebee gravity with an antisymmetric tensor. The Gibbons and Werner technique based on the Gauss-Bonnet theorem is utilized to calculate the bending angle of light. The effects of non-plasma and plasma medium on the bending angles are investigated. Furthermore, we examine the deflection angle $\Tilde{\alpha}$ in relation to the impact parameter $\sigma$ and minimal radius $r_{0}$ in both non-plasma and plasma mediums. Our findings indicate that the deflection angle is positively correlated with $r_{0}$, meaning that larger values of $r_{0}$ result in larger deflection angles and smaller values of $r_{0}$ result in smaller deflection angles. On the other hand, the deflection angle $\Tilde{\alpha}$ is inversely related to the impact parameter $\sigma$.

An experimental platform for laser-driven ion (sub-MeV) acceleration and potential applications was recently commissioned at the HiLASE laser facility. The auxiliary beam of the Bivoj laser system operating at GW peak power (~10 J in 5-10 ns) and 1-10 Hz repetition rate enabled a sta-ble production of high-current ion beams of multiple species (Al, Ti, Fe, Si, Cu, Sn). The pro-duced laser-plasma ion sources were fully characterized against the laser intensity on target (1013-1015 W/cm2) by varying the laser energy, focal spot size, and pulse duration. This al-lowed to provide accurate scaling laws of the maximum ion energy for the different target ma-terials investigated. Such experimental scaling laws are presented for the first time in the inves-tigated laser intensity range and for ns-class laser pulses, and allow to provide a qualitative in-terpretation of the laser-plasma interaction underpinning physics, thus to tune the main features of the accelerated ion beams (energy, temperature, and current). Such a detailed study was facil-itated by the large amount of data acquired at high repetition rate (1-10 Hz) provided by the Bivoj laser system. The versatility and tuneability of such high-repetition-rate laser-plasma ion sources are of po-tential interest for multidisciplinary user applications.

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

Plasma-activated water (PAW) is an emerging and promising green technology in the agriculture sector during recent years. The aim of this study was to examine the influence of the spraying of PAW and amino acid fertilizer concentrations on the physiological, biochemical and phytochemical characteristics of German chamomile varieties under field conditions. Method: The experiment was performed during 2020–2021 as a factorial using a randomized complete block design with three replications, in an arid and warm region. The factors contained five fertilizer levels (0 (control), 1, 2, 3 ml·L−1 amino acid and PAW) and three German chamomile cultivars Bona, Bodegold, Lianka). Physiological, biochemical and phytochemical traits such as plant height, fresh and dried flower weight, chlorophyll a, b, carotenoids, CHN elements, C:N ratio, total protein, amino acid profile, essential oil yield, apigenin content and major secondary metabolites were examined. Results: The ANOVA indicated that the impact of the cultivar and fertilizer was significant on all physiological, biochemical and phytochemical studied parameters. The amino acid fertilizer and PAW enhanced physiological features, hydrogen, C:N ratio, essential oil yield, apigenin content and main phytochemical compositions like chamazulene and α-bisabolol, but it had no incremental effect on the carbon, nitrogen, and total protein percentage. Conclusion: Findings revealed that the application of foliar amino acid fertilizer and PAW treatments improves physiological, biochemical and phytochemical parameters in German chamomile cultivars under field conditions.

We investigated new anodic coloring materials that are used as ion storage layers in complementary energy storage electrochromic devices (ESECDs) to enhance their electrochromic storage performance. In this study, we fabricated counter electrodes (ion storage layers) using IrO2 doping NiO (Ir: NiO) film through cathodic arc plasma (CAP) with varying surface charge capacities. We investigated the influence of MoO3-doped WO3 (Mo: WO3) film by various Ar/O2 gas flow ratios (1/4, 1/5, and 1/6). The ESECDs used in the demonstration were 10×10 cm2 in size. They achieved optical transmittance modulation of Ir: NiO- ESECDs (glass/ITO/ Mo: WO3/gel-polymer electrolytes/ Ir: NiO /ITO/glass), ΔT=53.3% (from Tbleaching (66.6%) to Tcoloration (13.1%)). The ESECDs had a quick coloration time of 3.58 seconds, a rapid bleaching time of 1.24 seconds, and high cycling durability. It remained at 45% transmittance modulation even after 3000 cycles. New anodic materials can provide an alternative to traditional active materials for bi-functional electrochromic batteries.

An 11-month-old castrated male Pomeranian presented with nonunion following a femoral fracture that occurred after femoral head and neck osteotomy. Radiography and computed tomography revealed severe atrophy of the proximal bone fragment and retardation of the ipsilateral distal fragment and tibia. An autogenous bone graft using coccygeal bone was performed, in which three-and-a-half coccyges were placed in series and fixed using an orthogonal locking plate. To promote bone healing and facilitate proper weight bearing and ambulation, bone morphogenetic proteins, biphasic calcium phosphate, platelet-rich plasma, passive range of motion exercises, transcutaneous electrical nerve stimulation, neuromuscular electrical stimulation, and low level laser therapy were applied. During the four-year follow-up, it was observed that the previously engrafted bone healed well and maintained stability over a prolonged period, resulting in the patient being able to walk and trot comfortably with good outcomes. However, some degree of lameness was noted during galloping owing to limb shortening and joint contracture.

Graphene/silicon (Si) heterojunction photodetectors are widely studied in detecting of optical signals from near-infrared to visible light. However, performance of the graphene/Si photodetectors is limited by defects created in the growth process and surface recombination at the interface. Herein, a remote plasma-enhanced chemical vapor deposition is introduced to directly grow graphene nanowalls (GNWs) at a low power, which can effectively improve the growth rate and reduce defects. Moreover, hafnium oxide (HfO2) grown by atomic layer deposition has been employed as an interfacial layer for the GNWs/Si heterojunction photodetector. It is shown that the high-k dielectric layer of HfO₂ acts as an electron blocking and hole transport layer, which minimizes the recombination and reduces dark current. By optimizing the thickness of HfO₂, an extremely low dark current of 3.85×10^(-10) A with a responsivity of 0.19 AW^(-1), as well as a specific detectivity of 1.38×10^12 Jones at zero bias can be obtained for the fabricated GNWs/HfO₂/Si photodetector. This work demonstrates a universal strategy to fabricate high-performance graphene/Si photodetectors.

The paper focuses on two unconventional magnetic field-based treatment regimes applied to an alloyed steel before applying a thermochemical treatment. This study was conducted in order to improve the behavior of the chosen material during the wear process. Increasing the wear resistance and the micro-hardness of the superficial layer obtained from the treatments are a priority, as well as improving the mechanical properties of a Cr-Mo alloyed steel. Thermomagnetic treatment, applied before plasma nitriding treatment, improves the mechanical properties of the base material, especially in the case of a steel with a considerable chromium content (1,02%). This paper is a review of my own researches in the last years.

The evidence supports the occurrence of environmentally induced paternal epigenetic inheritance shaping the offspring phenotype in the absence of direct or indirect paternal care, and the empirical results clearly indicate that sperm epigenetics is one of the major actors mediating these paternal effects. However, sperm often make up only a small fraction of the male ejaculate in animals. Males also have a complex mixture of proteins, peptides, types of small RNAs, and cell-free DNA fragments in their seminal fluid. These molecules are in close contact with reproductive cells, tissues, organs, and other molecules of both males and females during reproduction. Moreover, their production and use are very sensitive to environmental conditions which makes them potential modulators of environmentally and developmentally induced paternal effects on the next generation(s). Although there is some intriguing evidence of seminal fluid-mediated paternal epigenetic effects, the underlying molecular mechanisms remain poorly defined. In this review, I discuss the current evidence regarding the association between seminal fluid and environmentally induced paternal effects, the possible trajectories, and the mechanisms in which seminal fluid can involve to mediate paternal epigenetic inheritance.

The dynamics of a low-energy charged particle in an axis-symmetric magnetic field is known to be a regular superposition of periodic–although possibly incommensurate–motions. The projection of the particle orbit along the two non-ignorable coordinates (x,y) may be expressed in terms of each other: y=y(x), yet–to our knowledge–such a functional relation has never been directly produced in literature, but only by way of a detour: first, equations of motion are solved, yielding x=x(t),y=y(t), and then one of the two relations is inverted, x(t)→t(x). In this paper we present a closed-form functional relation which allows to express coordinates of the particle’ orbit without the need to pass through the hourly law of motion.

Although the idea of making electric weapons has emerged since the beginning of the 20th Century, the great number of technological problems made that such technology was not developed. During the Cold War, the US strategic programme Space Defensive Initiative paid a special attention to this category of weapons, but the experiments have demonstrated that the prototypes are too big, very heavy, and involve a very high energy consumption and low reliability. Under these circumstances, the authors have noticed the trend to design new types of electric weapons starting from the hybridization of some technologies: the compressed flux weapons, the plasma electromagnetic cannon, the electromagnetic weapons as the coil-gun and rail-gun.

Currently, one of the biggest issues when developing an ODS alloy is the competition established between the different oxide precursors during the precipitation of oxides which nature depends on their chemical composition. In the presence of various precursors, usually the one with the highest affinity to oxygen leads to the absence of the other oxides. In this work, a new process to equilibrate the local concentration of species and to decrease the competition among them is explained. A unique compound, containing the diverse oxide precursors as one complex oxide, is introduced in a prealloyed 14Cr Steel powder via mechanical alloying. Thus, generating environments enriched in Y, Ti and Zr which, after consolidation, refine the oxides precipitation improving the thermal stability of the alloy. SPS were used as consolidation technique to guarantee shorter sintering times and to maintain the nanostructure obtained. Mechanical properties were tested by tensile tests and Vickers microhardness.

We propose a new approach of extending the laser filament plasma channel. By adding a circular aperture quartz plate before the focusing lens, the extension of the plasma channel is doubled. The effects of different diameters, thicknesses of the circular aperture quartz plate and different pulse energies on the length of the plasma channel were investigated. The experimental results show that the thickness of the quartz plate and the depth of the hole have little effects on the plasma channel of the filament, and the diameter of the hole in the center of the quartz plate has a significant effect on the length of the optical filament. The moving-focus model is used to explain the extension of the optical filament.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 mJ, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). Atomic hydrogen spectra indicate axisymmetric shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO2:N2 gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Background: Plasma metabolites are associated with cognitive and physical function in the elderly. Because cerebral small vessel disease (SVD) and neurodegeneration are common causes of cognitive and physical function decline, the primary objective of this study was to investigate the associations of six plasma metabolites (two plasma phosphatidylcholines [PCs]: PC aa C36:5 and PC aa 36:6 and four sphingomyelins [SMs]: SM C26:0, SM [OH] C22:1, SM [OH] C22:2, SM [OH] C24:1) with magnetic resonance imaging (MRI) features of cerebral SVD and neurodegeneration in older adults. Methods: This study included 238 older adults in the Atherosclerosis Risk in Communities study at the fifth exam. Multiple linear regression was used to assess the association of each metabolite (log-transformed) in separate models with MRI measures except lacunar infarcts, for which binary logistic regression was used. Results: Higher concentrations of plasma PC aa C36:5 had adverse associations with MRI features of cerebral SVD (odds ratio of 1.69 [95% confidence interval: 1.01, 2.83] with lacunar infarct, and beta of 0.16 log [cm³] [0.02, 0.30] with log [White Matter Hyperintensities (WMH) volume]) while higher concentrations of 3 plasma SM (OH)s were associated with higher total brain volume (beta of 12.0 cm³ [5.5, 18.6], 11.8 cm³ [5.0, 18.6], and 7.3 cm³ [1.2, 13.5] for SM [OH] C22:1, SM [OH] C22:2, and SM [OH] C24:1, respectively). Conclusions: This study identified associations between certain plasma metabolites and brain MRI measures of SVD and neurodegeneration in older adults, particularly higher SM (OH) concentrations with higher total brain volume.

The circulating transcriptome is a valuable source of cancer biomarkers, which with the exception of miRNAs, remains relatively unexplored. To elucidate which RNAs are present in plasma from melanoma patients and which could be used to distinguish cancer patients of healthy individuals, we used next generation sequencing (NGS) and validation was carried out by qPCR and/or ddPCR. We identified 442 different microRNAs in samples, eleven of which were differentially expressed (P < 0.05). Levels of miR-134-5p and miR-320a-3p were significantly down-regulated (P<0.001) in melanoma samples (n = 96) compared to healthy controls (n = 28). Differentially expressed protein-encoding mRNA, 5´-fragments, were enriched for the angiopoietin, PAK and EIF2 pathways. Levels of ATM1, AMFR, SOS1 and CD109 gene fragments were up-regulated (P < 0.001) in melanoma samples (n=144) compared to healthy controls (n = 41) (AUC = 0.825). Over 40% of mapped reads were YRNAs, a class of non-coding RNAs that to date has been little explored. Expression levels of RNY3P1, RNY4P1 and RNY4P25 were significantly higher in patients with stage 0 disease, than either healthy controls or more advanced stage disease (P < 0.001). In conclusion, we have identified a number of novel RNA biomarkers, which most importantly we validated in multi-centre retrospective and prospective cohorts suggesting potential diagnostic use of these RNA species.

The resonance spectra of neutral silver indicate self-absorption for the studied Ag I lines at the wavelengths of 327.9 nm and 338.2 nm. The center dip is associated with self-reversal due to self-absorption in the plasma. The Q-switched radiation of 355 nm, 532 nm, or 1064 nm from a Nd:YAG laser device generates the plasma at the surface of silver nano-material targets, with experiments conducted in standard ambient temperature and pressure laboratory air. Procedures for recovery of the spectral line shapes confirm that over and above the effects of self-reversal, line shape distortion are important in the analysis. The work discusses parameters describing self-absorption when using fluence levels of 2 to 33 J/cm² to generate the plasma. Furthermore, subsidiary calibration efforts that utilize the hydrogen alpha line of the Balmer series show that the Ag I lines at 827.35 nm and 768.7 nm are optically thin.

This article discusses laser-induced laboratory-air plasma measurements and analysis of hydroxyl (OH) ultraviolet spectra. New experiments with Q-switched laser pulses illustrate occurrence of molecular recombination spectra for time delays of the order of several dozen of microseconds after plasma initiation. The computation of the emission spectra utilizes line strength data that are communicated as a supplementary file. Applications of detailed OH computations include laser-induced plasma and combustion analyses, to name but two applications.

Present research focus on the effect of different processing routes on physical and mechanical properties of nano Ti(CN) based cermet’s with metallic binders. Tungsten carbide (WC) is added as secondary carbide and Ni-Co are added as metallic binders in nano Ti(CN) based cermet processed via Conventional and Spark Plasma Sintering (SPS). Systematic comparison of composition and sintering conditions for different cermet’s’ systems is done to design the novel composition and sintering conditions. Nano TiCN powder was prepared by 30hr of ball milling. Highest density of >98.5% percent was achieved for SPS processed cermet’s sintered at 1200°C and 1250°C for 3 min. at 60 MPa pressure in comparison to conventionally sintered cermet’s at 1400°C for 1hr with two stage compaction process, uniaxially at 150 MPa and isostatically at 300 MPa pressure respectively. Comparison of XRD analysis of milled powders of different time intervals was done to understand the characteristics of the as received and milled powders. Peak broadening was observed after 5 hr. of ball milling, and it increased till 30hr. Also, peak broadening and refined carbide size was observed in XRD and SEM micrograph of SPS processed cermet. TEM analysis of milled powder showed internal structure having regular periodic arrangement of planes. SEM (BSE) images of all cermets primarily showed three major microstructural phases of core-rim-binder with black, grey and white contrast respectively. In the present sintering conditions high hardness of ~16 GPa and fracture toughness of ~9 MPa m1/2 was obtained for SPS processed cermets sintered at higher temperature.

Cryopreservation is a stressful process for sperm as it is associated with an increased production of reactive oxygen species (ROS). Elevated ROS levels, which create an imbalance with antioxidant capacity, may result in membrane lipid peroxidation (LPO), protein damage and DNA fragmentation. This study aimed to determine whether membrane LPO and DNA fragmentation of frozen-thawed horse sperm relies upon the antioxidant activity, including enzymes (superoxide dismutase (SOD), glutathione peroxidase (GPX), catalase (CAT), and paraoxonase type 1 (PON1)); non-enzymatic antioxidant capacity (Trolox equivalent antioxidant capacity (TEAC), plasma ferric reducing antioxidant capacity (FRAP), and cupric reducing antioxidant capacity (CUPRAC)); and the oxidative stress index (OSI), of their seminal plasma (SP). Based on total motility and plasma membrane integrity (SYBR14+/PI−) after thawing, ejaculates were hierarchically (p &lt; 0.001) clustered into two groups of good (GFE) and poor (PFE) freezability. LPO and DNA fragmentation (global DNA breaks) were higher (p &lt; 0.05) in PFE than in GFE, with LPO and DNA fragmentation (global DNA breaks) after thawing showing a positive relationship (p &lt; 0.05) with SP-OSI levels and ROS production. In addition, sperm motility and membrane integrity after thawing were negatively (p &lt; 0.05) correlated with the activity levels of SP antioxidants (PON1 and TEAC). The present results indicate that LPO and DNA fragmentation in frozen-thawed horse sperm vary between ejaculates. These differences could result from variations in the activity of antioxidants (PON1 and TEAC) and the balance between the oxidant and antioxidant components present in the SP.

The possibility of increasing the resource of steel fingers working in tandem with bronze bushings by plasma-electrolytic nitrocarburizing of the surface of medium carbon steel is shown. The phase composition, microhardness, morphology and surface roughness were studied. Tribological tests were carried out under dry friction conditions according to the shaft-pad scheme. It has been established that plasma-electrolytic nitrocarburizing of the surface of medium carbon steel at a temperature of 700 °C for 5 minutes leads to a decrease in a friction coefficient by 2.3 times, weight wear of steel by 24.9 times, and bronze counterbody by 5.9 times. At the same time, the contact stiffness increases 2.6 times. The type of wear is fatigue with dry friction and plastic contact. Changes in tribological characteristics are associated with the high hardness of the hardened steel surface together with the influence of dispersed nitrides and iron carbonitrides distributed in it.

Angiogenesis is new blood vessel formation from existing vessels and is a critical first step in tissue repair following chronic disturbances in healing and degenerative tissues. Chronic pathoanatomic tissues are characterized by a high number of inflammatory cells, overexpression of inflammatory mediators, such as tumor necrosis factor-α (TNF-α) and interleukin-1 (IL-1), the presence of mast cells, T cells, reactive oxygen species, and matrix metalloproteinases, and a decreased angiogenic capacity. Multiple studies have demonstrated that autologous orthobiological cellular preparations (e.g., platelet-rich plasma [PRP]) im-prove tissue repair and regenerate tissues. There are many PRP devices on the market. Unfortunately, they differ greatly in platelet numbers, cellular composition, and bioformulation. PRP is a platelet concentrate consisting of a high concentration of platelets with or without certain leukocytes, platelet-derived growth factors (PGFs), cytokines, molecules, and signaling cells. Several PRP products have immunomodulatory capacities that can influence resident cells in a diseased microenvironment, inducing tissue repair or re-generation. Generally, PRP is a blood-derived product, regardless of its platelet number and bioformulation, and the literature indicates both positive and negative patient treatment outcomes. Strangely, the literature does not designate specific PRP preparation qualifications that can potentially contribute to tissue re-pair. Moreover, the literature scarcely addresses the impact of platelets and leukocytes in PRP on (neo)angiogenesis other than a general one-size-fits-all statement that “PRP has angiogenic capabilities.” Here, we review the cellular composition of all PRP constituents, including leukocytes, and describe the importance of platelet dosing and bioformulation strategies in orthobiological applications to initiate angiogenic pathways that re-establish microvasculature networks, facilitating the supply of oxygen and nutrients to impaired tissues.

The present work was aimed at the investigation of effect of High Energy Ball Milling (HEBM) time on the sintering kinetics, structure, and properties of heavy tungsten alloy (HTA) W-7%Ni-3%Fe. The HTA samples were obtained from the nanopowders (20-80 nm) by conventional liquid phase sintering (LPS) in hydrogen and by Spark Plasma Sintering (SPS) in vacuum. The HTA density was shown to depend on the HEBM time non-monotonously that originates from the formation of non-equilibrium solid solutions in the W-Ni-Fe systems during HEBM. The SPS kinetics of the HTA nanopowders was shown to have a two-stage character, the intensity of which depends on the Coble diffusion creep rate and on the intensity of diffusion of the tungsten atoms in the crystal lattice of the -phase. The kinetics of sintering of the initial submicron powders have a single-stage character originating from the intensity of the grain boundary diffusion in the -phase. The dependencies of the hardness and of the yield strength on the grain sizes were found to obey the Hall-Petch relation. The hardness, strength, and dynamic strength in the compression tests of the fine-grained tungsten alloys obtained by SPS and LPS were studied.

The objective of this study was to evaluate the potential benefits of feeding spray-dried porcine plasma (SDPP) to pigs infected with African swine fever virus (ASFV). Two groups of twelve weaned pigs each were fed with CONVENTIONAL or 8% SDPP enriched diets. Two pigs (trojans)/group) were injected intramuscularly with the pandemic ASFV (Georgia 2007/01) and comingled with the rest of the pigs (1:5 trojan:naïve ratio) to simulate a natural route of transmission. Trojans developed ASF and died within the first week after inoculation but contact pigs did not develop ASF, viremia or seroconversion. Therefore, three more trojans per group were introduced to optimize the ASFV transmission (1:2 trojan:naïve ratio). Blood, nasal and rectal swabs were weekly harvested and at end of the study, ASFV-target organs collected. After the second exposure, rectal temperature of conventionally fed contact pigs increased >40.5˚C while fever was delayed in the SDPP contact pigs. Additionally, PCR Ct values in blood, secretions and tissue samples were significantly lower (P<0.05) for CONVENTIONAL compared to SDPP contact pigs. Under these study conditions, contact exposed pigs fed SDPP had delayed ASFV transmission and reduced virus load, likely by enhanced specific T-cell priming after the first ASFV-exposure.

The evolution in the post shock nonequilibrium relaxation in a hypersonic plasma flow was investigated during a shock’s reflection off a thermal discontinuity. Within a transitional period, the relaxation zone parameters past both, the reflected and transmitted waves, evolve differently compared to that in the incident wave. In a numerical example for the non-dissociating N₂ gas heated to 5000 K/10,000 K across the interface and M = 3.5, the relaxation time for the transmitted wave is up to 50% shorter and the relaxation depth for both waves is significantly reduced, thus resulting in a weakened wave structure. The results of extension into larger values of heating strength and the shock Mach numbers are discussed. The findings can be useful in the areas of research involving strong shocks interacting with optical discharges or other heated media on the scale where the shock structure becomes important.

The general coupling between particle transport and ionization-recombination processes in hot plasma is considered on the key concept of equilibrium charge state (CS) transport. A theoretical interpretation of particle and CS transport is gained in terms of a two-dimensional (2D) Markovian stochastic (random) processes, a discrete 2D Fokker-Plank-Kolmogorov equation (in charge and space variables) and generalized 2D coronal equilibrium between atomic processes and particle transport. The basic tool for analysis of CS equilibrium and transport is the equilibrium cell (EC) (two states on charge and two on space), which presents (i) a unit phase volume, (ii) the characteristic scale of local equilibrium, (iii) a comprehensive solution for the simplest nonlinear relations between transport and atomic processes. The approach opens up new perspectives on transport studies: (i) the direct modelling of equilibrium and transport of impurity using the atomic data base, (ii) recovery of the complete recombination rate profile based on knowledge of density profiles and ionization rate profiles, (iii) the local transport analysis, based on the reduction of the equilibrium set to the single EC (in particular, central or edge), (iv) analysis of the reduced transport coefficients (diffusion and convection) on the density profile measurements.

Steroid analysis is important in the clinical assessment of endocrine function in health and disease. Although tandem mass spectrometry methods coupled with chromatographic separation are considered the gold standard analytical technique in this setting, enabling profiling of multiple steroids in a single sample, sample processing can be labour-intensive. Here we present a simple, efficient automated 96-well Supported Liquid Extraction method with dichloromethane/isopropanol as organic solvent, carried out on a Extrahera automated sample handler (Biotage), which completes sample preparation of 80 plasma samples (200µL) in 90 minutes. Compounds were separated on a Kinetex C18 column (150x3mm;2.6um) using a mobile phase of methanol and water (0.1% formic acid). The run time was 16 minutes on a Nexera uHPLC system (Shimadzu) with a QTrap 6500+ linear ion trap mass spectrometer (AB Sciex). Precisions ranged 8.1 to 18.1% RSD, bias -10.1-5.8%, and extraction recoveries 73.5-111.9%. LOQs ranged between 0.025–0.500 ng/mL.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

The paper focuses of the interaction between tungsten (W) wire and microwave field in carbon dioxide (CO2) atmosphere. Our experimental set-up uses a microwave plasma generator in order to generate the plasma from the metallic wires. The microwave plasma generator contain a cylindrical cavity - TM_011 propagation modes, commercial source (magnetron) having the 2.45 GHz frequency at 800 W microwave and power supply. In the focal point of the cylindrical cavity we have a high energy of the electromagnetic radiation. The metallic wires from this area will be vaporized and ionized having as effect CO2 dissociation. The electron temperature regarding metallic plasma produced was estimated using the ratio of atomic emission lines acquired by a high definition of the optical multichannel spectrometer. Determination of the CO2 dissociation quantity was estimated measuring of the carbon monoxide (CO) resulting of the CO2 dissociation process. We obtained a high electron temperature of the plasma and a strong dissociation of the CO2.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

A hand-held laser-induced breakdown spectroscopy device was used to acquire spectral emission data from laser-induced plasmas created on the surface of cerium-gallium alloy samples with Ga concentrations ranging from 0 to 3 weight percent. Ionic and neutral emission lines of the two constituent elements were then extracted and used to generate calibration curves relating the emission line intensity ratios to the gallium concentration of the alloy. The Ga I 287.4 nm emission line was determined to be superior for the purposes of Ga detection and concentration determination.A limit of detection below 0.25% was achieved using a multivariate regression model of the Ga I287.4 nm line ratio versus two separate Ce II emission lines. This LOD is considered a conservative estimation of technique’s capability given the type of the calibration samples available and low power( 5 mJ per 1 ns pulse) and resolving power (λ/∆λ= 4000) of this handheld device. Nonetheless, the utility of the technique is demonstrated via a detailed mapping analysis of the surface Ga distribution of a Ce-Ga sample which reveals significant heterogeneity resulting from the sample production process.

Researchers from around the world are looking for better and cheaper ozone production. One of the methods increasing the efficiency of ozone production is the use to a rotating electrode presented in this paper. Experiments were carried out which shows that the most important parameters are the materials used on the electrodes and the condition of its surface. The metallographic investigations of the electrodes after continuous monthly work was made, which show how the raids layers are formed. As a result of working in a highly oxidizing environment, the electrode is oxidized in the process of chemical corrosion. It is obvious that the layer of corrosion products created during the work of the plasma reactor isolates the surface of the electrode, which reduces the intensity of the electric field, causing a decrease in the amount of plasma generated, which is a direct cause of lowering the concentration of ozone during this process. The dynamics of plasma generation process and the type of electrode material working in changing process conditions are the decisive factors influencing the concentration of ozone produced. The influence of the medium, which is the electrode material, depends mainly on its resistance to corrosion in the environment of dynamically changing conditions, e.g. electrode rotation, oxygen flow through the rotating electric field and the long monthly working time of the plasma reactor.

Ti and Ti alloys are materials usually used in contact with hard tissue for applications such as artificial joints and dental implants. Ti6Al4V is a very common alloy used for dental implants, owing to its good mechanical properties and corrosion resistance. Nevertheless, because of uncertainties regarding the toxicity of vanadium and its influence on the human body, other Ti alloys containing no vanadium and retaining suitable properties are used. In this work Ti6Al4V and Ti6Al7Nb were oxidized in a water solution of calcium acetate (Ca(CH3COO)2) and calcium glycerophosphate (Ca(PO4CH(CH2OH)2) by Plasma Electrolytic Oxidation (PEO) for 20 minutes and then were hydrothermally treated (HTT) in water (pH=7) and in potassium hydroxide (KOH) solution (pH=11) for 2 hours at 200°C in a pressurized reactor. The surface morphologies, elemental composition and phase components were characterized by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD), respectively. The surface roughness was measured by Atomic Force Microscope (AFM) and thickness measurements were made by SEM and thickness gauge. Also, corrosion tests were made to evaluate the corrosion behavior of the two alloys. The aim of this study is to compare two viable Ti alloys, Ti6Al4V and Ti6Al7Nb, and to attain on their surface hydroxyapatite (HA) coating improving the osseointegration, as it simulates a human bone.

Recent advances and demands in clinical applications drive a large amount of research to hydroxyapatite (HA) composite coatings fabricated by plasma spray. However, lower degree of HA crystallinity related to high temperature exposure in plasma spray usually leads to rapid weakening and disintegration of HA coatings and often promotes inflammatory responses in the surrounding tissue. In this research, graphene nanosheet (GNS) reinforced HA coatings were fabricated using plasma spray and followed by heat and hydrothermal treatment (hereafter referred to as thermal treatment). The addition of GNSs resulted in competing phenomenon to influence HA crystallinity viz. increased portion of the partially melted/unmelted zones and higher cooling rate during splat formation, leading to slight increase in HA crystallinity (~46.0-51.3%) in the as-sprayed coating. XRD and FTIR results showed that thermal treatment was capable of inducing significant transformation of amorphous HA to the crystalline form and removing other foreign non-HA compounds through regaining OH- ion, and therefore HA coatings displayed ~45.5-47.1% improvements in HA crystallinity regardless of addition or not of the GNS nanofillers. Microstructure observations revealed that thermal treatment enabled microcrack propagation due to stresses caused by crystallisation and phase transformations, and the residual partially melted/unmelted zone of the thermally treated GNS/HA coating was significantly decreased in size. More importantly, the added GNSs contributed greatly to the significant increase in surface nanoroughness of the thermally treated HA coatings owing to the fact that much more structural defects along with the GNSs mainly induced by thermal treatment might act as nucleation sites to accelerate HA nanoparticle precipitation, which would be beneficial for the improved adhesion strength of the osteoblast cells on the coating surface.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 milli-Joules, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). The atomic H spectra, collected following optical breakdown in ultra-high-pure hydrogen and 9:1 mixtures of ultra-pure hydrogen and nitrogen gases, indicate spherical shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO₂:N₂ gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

The effects of tyrosine on plasma response and cognition in aging are unknown. We assessed the dose-dependent response to tyrosine administration in older adults in both plasma tyrosine concentrations and working memory performance. In this double blind randomized cross-over trial 17 older adults (aged 60-75 years) received a single administration of 100, 150 or 200 mg/kg body weight of tyrosine. For comparison, 17 young adults (aged 18-35 years) received a dose of 150 mg/kg body weight of tyrosine. Tyrosine plasma concentrations were determined before and 90, 120, 150, 180, 210 and 240 minutes after tyrosine intake. Working memory was assessed using the N-back task at 90 minutes after tyrosine administration. Older adults showed a dose-dependent increase in plasma tyrosine concentrations (p<.001), and the plasma response was higher than for young adults with the same dose (p<.001). Load-dependent working memory performance decreased with higher doses of tyrosine (p=.048), especially in older adults with greater dose-dependent plasma tyrosine responses (p=.035). Our results show an age-related increase in plasma tyrosine response, which was associated with a dose-dependent decline in cognitive functioning in older adults.

Rare earth rich magnesium alloys are used in aerospace and automotive fields because of their high specific strength and good castability. However, due to their low corrosion resistance, protective surface treatments, such as conversion coating or electroless plating are necessary, when they have to be used in humid or corrosive environments. The present study was aimed to evaluate the effect of Plasma Electrolytic Oxidation (PEO) and different surface roughness (Ra≈0.8 μm and Ra≈0.3 μm) on the rotating bending fatigue of an innovative Mg alloy, with a high content of Nd (up to 3.1 wt%) and Gd (up to 1.7 wt %). Fatigue tests revealed a 15% decrease in the fatigue strength of the PEO treated alloy (fatigue strength = 88 MPa) with respect to the bare alloy (fatigue strength = 103 MPa). The reduction of fatigue strength was mainly due to the residual tensile stresses induced by the PEO treatment. The effect of surface roughness on the bare alloy was, instead, negligible. The mechanisms of crack initiation were similar in the untreated and PEO treated alloy, with crack nucleation sites located in correspondence of large facets of the cleavage planes.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

The possibility of a shock wave recovery at a discrete closed interface with a heated gas has been investigated. A two-dimensional model applied to conditions of optical discharges featuring spherical, elliptical, and drop-like configurations demonstrated that non-symmetry in the shock refraction contributes to the specific mechanism of recovery other than simply its compensation. Even though the full restoration of the hypersonic flow state doesn’t occur in a strict sense of it, clear reverse changes toward the initial shape of the shock front eventually take place, thus creating an appearance of a full recovery seen in experiments. From analysis for different interfaces symmetries, the factors determining the recovery dynamics are identified. The results are directly applicable to the problem of energy deposition into a hypersonic flow, however it can be useful anywhere else where the flow modifications following the interaction are important. The dimensionless form of the equations allows applications on any scale other than that demonstrated for the optical discharges.

A comprehensive lipid profile was analyzed in patients with non-small cell lung cancer (NSCLC) using nanoflow ultrahigh-performance liquid chromatography-electrospray ionization-tandem mass spectrometry. The study investigated 297, 202, and 166 lipids in saliva, plasma, and fecal samples, respectively, comparing NSCLC patients to healthy controls. Lipids with significant changes (&gt;2-fold, p&lt;0.05) were further analyzed in each sample type. Both saliva and plasma exhibited similar lipid alteration patterns in NSCLC, but saliva showed more pronounced changes and fecal lipids had weak correlation with those of saliva and plasma. Total triglycerides (TGs) increased (&gt;2–3 folds) in plasma and saliva but decreased in fecal samples. Three specific TGs (50:2, 52:5, and 54:6) were significantly increased in NSCLC across all sample types. A common ceramide species (d18:1/24:0) decreased in both plasma and saliva but increased in fecal samples. Additionally, phosphatidylinositol 38:4 decreased by approximately 2-fold in plasma and saliva. Phosphatidylserine 36:1 was selectively detected in saliva and showed a subsequent decrease, making it a potential biomarker for predicting lung cancer. The study identifies 27 salivary, 10 plasma, and 16 fecal lipids as candidate markers for NSCLC by statistical evaluations. Moreover, it highlights the potential of saliva in understanding changes in lipid metabolism associated with NSCLC.

Pastes containing reduced graphene oxide (rGO) and LiCl-Mn(NO3)2·4H2O are screen-printed on a carbon cloth substrate and then calcined using a nitrogen atmospheric-pressure-plasma jet (APPJ) for conversion into rGO-LiMnOx nanocomposites. The APPJ processing time is within 300 s. RGO-LiMnOx on carbon cloth is used to sandwich H2SO4, LiCl, or Li2SO4 gel electrolytes to form hybrid supercapacitors (HSCs). The areal capacitance, energy density, and cycling stability of the HSCs are evaluated using electrochemical measurement. The Li2SO4 gel electrolyte HSC exhibits the highest areal capacitance and energy density but lower cycling stability. By contrast, the H2SO4 gel electrolyte HSC exhibits better cycling stability but lower areal capacitance and energy density.

The COVID-19 pandemic has raised questions about indirect impact in pregnant women on the development of their future children. Investigating the characteristics of lipid metabolism in the "mother-placenta-fetus" system can give information about the pathophysiology of COVID-19 infection during pregnancy. 234 women were included in study. Maternal plasma, cord blood, amniotic fluid lipidome were analyzed using HPLC-MS/MS. Differences in lipid profile were searched by Manna-Whitney and Kruskall-Wallis test, diagnostic model based on logistic regres-sion were bilt by AIC. Elevation levels of lysophospholipids, triglycerides, sphingomyelins, and oxidized lipids was registered in patients’ after COVID-19 maternal and cord plasma. An increase in maternal plasma sphingomyelins and oxidized lipids was observed in cases of infection during the second trimester. In amniotic fluid, compared to the control group, nine lipids are reduced, six lipids are elevated. Levels of phosphoglycerides, lysophosphoglycerides, and phosphatidylinosi-tols decreased during infection in the second and third trimesters of pregnancy. Newborn’s health diagnostic model based on maternal plasma were developed for each group and exhibit good di-agnostic value (AUC> 0.85). Maternal and cord plasma’s lipidome changes during delivery, asso-ciated with Covid-19 infection during pregnancy, are synergistic. The most significant disturbances occur with infections in the second trimester of pregnancy.

Platelet and fibrin-rich orthobiologic products, such as autologous platelet concentrates, have been extensively studied and appreciated for their beneficial effects in multiple conditions. PRP and its derivatives, including PRF, have demonstrated encouraging outcomes in clinical and laboratory settings, particularly in the treatment of musculoskeletal disorders such as OA. Although PRP and PRF have distinct characteristics, they share similar properties. The relative abundance of platelets, peripheral blood cells and molecular components in these orthobiologic products stimulate numerous biological pathways. These include inflammatory modulation, augmented neovascularization, and delivery of pro-anabolic stimuli that regulate cell recruitment, proliferation, and differentiation. Furthermore, the fibrinolytic system, which is sometimes overlooked, plays a crucial role in musculoskeletal regenerative medicine by regulating proteolytic activity and promoting the recruitment of inflammatory cells and MSCs in areas of tissue regeneration, such as bone, cartilage, and muscle. PRP acts as a potent signaling agent; however, it diffuses easily, while the fibrin from PRF offers a durable scaffolding effect that promotes cell activity. The combination of fibrin with hyaluronic acid, another well-studied orthobiologic product, has been shown to improve its scaffolding properties, leading to more robust fibrin polymerization. This supports cell survival, attachment, migration, and proliferation. Therefore, the administration of the "power mix" containing HA and autologous PRP + PRF may prove to be a safe and cost-effective approach in regenerative medicine.

Applying of blood biopolymers to regulate the phase composition is promising in designing the hydroxyapatite-based hybrid biomaterials with controllable resorbability. Hybrid materials based on hydroxyapatite and platelet-poor plasma (PPP) were formed in conditions of chemical precipi-tation at pH 11, [Ca2+] / [PO43–] ratio 1.67, PPP volume fraction of 6–24%, maturing time of 4–9 days. Mineral component of the materials was represented as 53% hydroxyapatite / 47% amor-phous calcium phosphate after 4 days of maturation, and 100% hydroxyapatite after 9 days of maturation. Varying PPP content from 6% to 24% provided forming of materials with rather de-fined content of amorphous calcium phosphate and biopolymer component, having desired mor-phology ranging from typical apatitic conglomerates to hybrid apatite-biopolymer fibers. Co-precipitated hybrid materials based on hydroxyapatite and PPP are promising for bone regen-eration in osteoplastic and maxillofacial applications.

Fifty years on from the classical fluid-mosaic model of Singer and Nicolson, current views of the plasma membrane portray a much more complex view of this interface region. Compartmentalization, together with transbilayer and lateral asymmetries, provide the structural foundation for functional specializations at the cell surface, including the active role of the lipid microenvironment in the modulation of membrane-bound proteins. The chemical synapse, the site where neurotransmitter-coded signals are decoded by neurotransmitter receptors, adds another layer of complexity to the plasma membrane architectural intricacy, mainly due to the need to accommodate a sizeable number of molecules in a minute subcellular compartment with dimensions barely reaching the micrometer. In this review, we discuss how Nature has developed suitable adjustments to accommodate different types of membrane-bound receptors and scaffolding proteins via membrane microdomains, and how this “efford-sharing” mechanism has evolved to optimize crosstalk or separation or coupling where/when appropriate. To this end, we use a fast ligand-gated neurotransmitter receptor, the nicotinic acetylcholine receptor, and a second-messenger G-protein coupled receptor, the cannabinoid receptor, as paradigmatic example.

Pertussis is a vaccine-preventable disease caused by the bacterium Bordetella pertussis. Over the past years, the incidence and mortality of pertussis increased significantly. A possible cause is the switch from whole cell to acellular pertussis vaccines, although other factors may also contribute. To develop future vaccines and improve current vaccination strategies, it is critical to understand factors influencing the generation of immunological memory. We applied high-dimensional flow cytometry to investigate changes in B cells in individuals of different ages and distinct priming backgrounds upon administration of an acellular pertussis booster vaccine. These findings were correlated to vaccine-specific plasma cells and serum Ig levels. Expansion and maturation of plasma cells 7 days post-vaccination was the most prominent cellular change in all age groups, and was most pronounced for more mature IgG1+ plasma cells. Cellular responses were stronger in individuals primed with whole cell vaccine than in individuals primed with acellular vaccine. Moreover, IgG1+ plasma cell expansion weakly correlated with Prn- and PT- specific serum IgG levels. Our study points at plasma cells as a potential early cellular marker of an immune response and contributes to understanding differences in immune responses between age groups and priming backgrounds.

Most studies on the association of in utero exposure to cigarette smoking and childhood overweight or obesity (OWO) were based on maternal self-reported smoking data and few were based on objective biomarkers. In this study, we evaluated the associations between self-reported and biomarkers of in utero exposure to cigarette smoking with risk of childhood OWO. We analyzed data from 2351 mother-child pairs in the Boston Birth Cohort, a US low-income minority cohort that enrolled children at birth and followed prospectively up to age 18 years. In utero smoking exposure was measured by maternal self-report and by maternal and cord plasma cotinine and hydroxycotinine metabolites. We assessed the individual and joint associations of each smoking exposure measure and maternal OWO with childhood OWO using multinomial logistic regressions. We used nested logistic regressions to investigate the childhood OWO prediction performance when adding maternal and cord plasma biomarkers as input covariates on top of self-reported data. Our results demonstrated that in utero cigarette smoking exposure defined by self-report and by maternal or cord metabolites were consistently associated with increased risk of long-term child OWO. Adding maternal and cord plasma biomarker information to self-reported data improved the prediction accuracy of long-term child OWO risk.

In this article, we calculate the deflection angle of tidal charged black hole (TCBH) in weak field limits. First we obtain the Gaussian optical curvature and then apply the Gauss-Bonnet theorem on it. With the help of Gibbons-Werner method, we are able to calculate the light's deflection angle by TCBH in weak field limits. After calculating the deflection angle of light, we check the graphical behavior of TCBH. Moreover, we further find the light's deflection angle in the presence of plasma medium and also check the graphical behavior in the presence of plasma medium. Moreover, we investigate the shadow of TCBH.For calculating the shadow, we first find the null geodesics around the TCBH and then find its shadow radius. We also obtain TCBH's shadow in the plasma medium. Hence, we discuss the shadow of the TCBH using the $M87^{*}$ parameters announced by the Event Horizon Telescope.

To combat infections on biomedical devices, antimicrobial coatings have attracted considerable attention, including coatings comprising naturally occurring antimicrobial peptides (AMPs). In this study the aim was to explore performance upon extended challenge by bacteria growing in media above samples. The AMPs LL37, Magainin 2, and Parasin 1 were covalently grafted onto a plasma polymer platform, which enables application of this multilayer coating strategy to a wide range of biomaterials. Detailed surface analyses were performed to verify the intended outcomes of the coating sequence. Samples were challenged by incubation in bacterial growth media for 5 and 20 hrs. Compared with the control plasma polymer surface, all three grafted AMP coatings showed considerable reductions in bacterial colonization even at the high bacterial challenge of initial seeding at 1x107 CFU, but there were increasing numbers of dead bacteria attached to the surface. All three grafted AMP coatings were found to be non-toxic to primary fibroblasts. These coatings thus could be useful to produce antibacterial surface coatings for biomaterials, though possible consequences arising from the presence of dead bacteria need to be studied further, and compared to non-fouling coatings that avoid attached dead bacteria.

The Ras family of proteins is tethered to the inner leaflet of the cell membranes which play an essential role in signal transduction pathways that promote cellular proliferation, survival, growth, and differentiation. KRas-4B, the most mutated Ras isoform in different cancers, has been under extensive study for more than two decades. Here we have focused our interest on the influence of cholesterol on the orientations that KRas-4B adopts with respect to the plane of the anionic model membranes. How cholesterol in the bilayer might modulate preferences for specific orientation states is far from clear. Herein, after analyzing data from in total 4000 ns-long MD simulations for four KRas-4B systems, properties such as the area per lipid and thickness of the membrane as well as selected radial distribution functions, penetration of different moieties of KRas-4B, and internal conformational fluctuations of flexible moieties in KRas-4B have been calculated. It has been shown that high cholesterol content in the PM favors OS1, exposing the effector-binding loop for signal transduction in the cell from the atomic level. We confirm that high cholesterol in the PM helps KRas-4B mutant stay in its constitutively active state, which suggests that high cholesterol intake can increase mortality and may promote cancer progression for cancer patients. We propose that during the treatment of KRas-4B-related cancers, reducing the cholesterol level in the PM and sustaining cancer progression by controlling the plasma cholesterol intake might be taken into account in anti-cancer therapies.

Convalescent blood product therapy has been introduced since early 1900s to treat emerging infectious disease based on the evidence that polyclonal neutralizing antibodies can reduce duration of viremia. Recent large outbreaks of viral diseases for whom effective antivirals or vaccines are still lacking has revamped the interest in convalescent plasma as life-saving treatments. This review summarizes historical settings of application, and surveys current technologies for collection, manufacturing, pathogen inactivation, and banking, with a focus on COVID-19.

Background: Prostate cancer (PCa) is characterized by significant heterogeneity in its molecular, genomic, and immunologic characteristics. Methods: Whole transcriptome RNAseq data from The Cancer Genome Atlas of prostate adenocarcinomas (n=496) was utilized. The immune microenvironment was characterized using the CIBERSORTX tool to identify immune cell type composition. Unsupervised hierarchical clustering was performed based on immune cell type content. Analyses of progression-free survival (PFS), distant metastases, and overall survival (OS) were performed using Kaplan-Meier estimates and Cox-regression multivariable analyses. Results: Four immune clusters were identified, largely defined by plasma cell, CD4+ Memory Resting T Cells (CD4 MR), M0 and M2 macrophage content (CD4 MRHighPlasma CellHighM0LowM2Low, CD4 MRLowPlasma CellHighM0LowM2Low, CD4 MRHighPlasma CellLowM0HighM2Low, and CD4 MRHighPlasma CellLowM0LowM2High). The two macrophage-enriched/plasma cell non-enriched clusters (3&4) demonstrated worse PFS (HR 2.24, 95% CI 1.46–3.45, p=0.0002) than the clusters 1&2. No metastatic events occurred in the non-macrophage-enriched clusters. Comparing clusters 3 vs 4, in patients treated by surgery alone, cluster 3 had zero progression events (p<0.0001). However, cluster 3 patients had worse outcomes after post-operative radiotherapy (p=0.018). Conclusion: Distinct tumor immune clusters with a macrophage-enriched phenotype and reduced plasma cell enrichment independently characterize an aggressive phenotype in localized prostate cancer that may differentially respond to treatment.

The need to understand the process by which particles, including solar wind and coronal ions as well as pickup ions, are accelerated to high energies (ultimately to become anomalous cosmic rays) motivate a multi-fluid shock wave model which includes kinetic effects (e.g. ion acceleration) in an electromagnetically self-consistent framework. Particle reflection at the cross-shock potential leads to ion acceleration in the motional electric field and thus anisotropic heating and pressure in the shock layer, with important consequences for the multi-fluid dynamics. This motivates development of a multi-fluid model of solar wind electrons and ions treated as fluid, coupled self-consistently with a small population of kinetically treated ions (e.g. pickup ions.) Consideration of both the time dependent and steady state regimes, indicate that such a multi-fluid approach is necessary for resolving the, Debye scale, particle reflecting cross-shock potential and subsequent dynamics. To study charge separation effects in narrow, supersonic wave layers we consider a reduction of the system to the steady state for cold ions and hot electrons and find two types of solitary waves inherent to the reduced two-fluid system in this limiting case.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

SMAD ubiquitination regulatory factor 1 (Smurf1) is a Nedd4 family E3 ubiquitin ligase that regulates cell motility, polarity and TGFβ signaling. Smurf1 contains an N-terminal protein kinase C conserved 2 (C2) domain that targets cell membranes and is required for interactions with membrane-localized substrates such as RhoA. Here we investigated the lipid-binding mechanism of Smurf1 C2, revealing a general affinity for anionic membranes in addition to a selective affinity for phosphoinositides (PIPs). We found that Smurf1 C2 localizes not only to the plasma membrane but also to negatively charged intracellular sites, acting as an anionic charge sensor and selective PIP-binding domain. Site-directed mutagenesis combined with docking/molecular dynamics simulations revealed that the Smurf1 C2 domain loop region primarily interacts with PIPs and cell membranes, as opposed to the β-surface cationic patch employed by other C2 domains. By depleting PIPs from the inner leaflet of the plasma membrane, we found that PIP binding is necessary for plasma membrane localization. Finally, we used a Smurf1 cellular ubiquitination assay to show that the amount of ubiquitin at the plasma membrane interface depends on the lipid-binding properties of Smurf1. This study shows the mechanism by which Smurf1 C2 targets membrane-based substrates and reveals a novel interaction based on PI(4,5)P2 and PIP3 selectivity.

The synergistic efficacy of combined treatment mild heat (MH) and dielectric barrier discharge (DBD) plasma in Bacillus cereus-contaminated red pepper powder was tested. A cocktail of three strains of B. cereus (NCCP 10623, NCCP 14579, ATCC 11778) was inoculated onto red pepper powder and then treated with MH (60 ℃ for 5-20 min) and DBD plasma (5-20 min). Treatment with MH and DBD plasma alone for 5~20 min resulted in reductions of 0.23~1.43 and 0.12~0.96 log CFU/g, respectively. Combined treatment with MH and DBD plasma was the most effective at reducing B. cereus counts on red pepper powder and resulted in log-reductions of ≥ 6.0 log CFU/g. The largest synergistic values (4.24-4.42 log) against B. cereus in red pepper powder were obtained by the combination of 20 min MH and 5~15 min DBD plasma. Hunter color ‘‘L’’, ‘‘a’’, and ‘‘b’’ values of the combination-treated samples were not significantly different from those of non-treated samples. Also, no significant (p > 0.05) differences in pH values between samples were observed. Therefore, these results suggest that the combination of MH treatment and DBD plasma can be potentially utilized in the food industry to effectively inactivate B. cereus without incurring quality deterioration of red pepper powder.

Q-switched laser radiation at wavelengths of 355 nm, 532 nm, and 1064 nm from a Nd: YAG laser was used to generate plasma in laboratory air at the target surface made of compressed nano-silver particles of size 95 ± 10 nm. The emitted resonance spectra from the neutral silver at wavelengths of 327.9 nm and 338.2 nm indicate existence of self-reversal in addition to plasma self-absorption. Both lines were identified in emission spectra at different laser irradiation wavelengths with characteristic dips at the un-shifted central wavelengths. These dips are usually associated with self-reversal. Under similar conditions, plasmas at the corresponding bulk silver target were generated. The recorded emission spectra were compared to those obtained from the nano-material target. The comparisons confirm existence of self-reversal of resonance lines that emerge from plasmas produced at nano-material targets. This work suggests a method for recovery of the spectral line shapes and discusses practical examples. In addition, subsidiary calibration efforts that utilize the Balmer series Hα-line reveal that other Ag I lines at 827.35 nm and 768.7 nm are optically thin under variety of experimental conditions and are well-suited as reference lines for measurement of the laser plasma electron density.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

Nanopowders are continuously under investigation as they open new perspectives in numerous fields. There are two main challenges to stimulate their development: sufficient low-cost high throughput synthesis methods leading to a production with well-defined and reproducible properties, and for ceramics, conservation of their nanostructure after sintering. In this context, this paper presents the synthesis of a pure nanosized powder of ZnO (dv₅₀ ~ 60 nm, easily redispersable) by using a continuous Segmented Flow Tubular Reactor (SFTR), which has previously shown its versatility and its robustness, ensuring a high powder quality and reproducibility over time. A higher scale of production can be achieved based on a “scale-out” concept by replicating the tubular reactors. The sinterability of ZnO nanopowders synthesized by the SFTR was studied, by natural sintering at 900 °C and 1100 °C, and Spark Plasma Sintering (SPS) at 900 °C. The performances of the synthesized nanopowder were compared to a commercial ZnO nanopowder of high quality. The samples obtained from the synthesized nanopowder could not be densified at low temperature by traditional sintering, whereas SPS led to a fully dense material after only 5 minutes at 900 °C, while limiting the grain growth and thus leading to a nanostructured material.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

Accelerating, exact, explicit and simple solutions of relativistic hydrodynamics allow for a simple and natural description of highly relativistic p+p collisions. These solutions yield a finite rapidity distribution, thus they lead to an advanced estimate of the initial energy density of high energy collisions. We show that such an advanced estimate yields an initial energy density in $\sqrt{s}=7$ and 8 TeV p+p collisions at LHC around or above the critical energy density from lattice QCD, and a corresponding initial temperature above the critical temperature from QCD and the Hagedorn temperature. This suggests that the collision energy of the LHC corresponds to a large enough initial energy density to create a non-hadronic perfect fluid even in pp collisions. %We also show, that several times the %critical energy density may have been reached in high multiplicity events, hinting at a non-hadronic medium created in %high multiplicity $\sqrt{s}=7$ and 8 TeV p+p collisions.

Abstract: Presence in a recipient of antibodies directed against donor specific antigens represent a major obstacle in transplanting such patients. Removal of these antibodies represents a challenge for physicians dealing with kidney transplantation. Several strategies, techniques and old and new drugs are to date used to desensitize these patients. Desensitization may occur before transplantation or at the time of transplantation or after transplantation according whether physicians deal with living or deceased donors. Different techniques may be used to reveal the presence of antibodies in the recipients; each technique has different sensitivity and specificity, different advantages and disadvantages. The target of the drugs used to desensitize are B cells, Plasma cells, the antibodies themselves and finally, the complement that is the final actor causing tissue disruption. If B cells are relatively easy to be targeted, more difficult are the plasma cell. Indeed, several new drugs are used in randomized trials also to defeat plasma cells. Antibodies may be removed rather easily, but often their removal is followed by a rebound. Complement is not easy to be defeated and new drugs are to date used to be successful in this action. However is to date possible to desensitize many patients and to obtain successful transplantation.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

Alzheimer’s disease (AD) is one of the most widespread neurodegenerative diseases affecting people averaging over 65 years. It manifests with severe cognitive damage, loss of memory, impairment in performing activities, ventricular expansion and final dementia. AD is associated with the deposit of amyloid β protein (Aβ) plaques, intracellular neurofibrillary tangles (NFTs), progressive inflammation and impairment of synaptic transmission and of mitochondrial function. Due to the poor diagnostic tools for the early stages of the disease, proteomics biomarkers have gained a paramount role because they can monitor the prodromal variations of the disease-linked molecular changes. Further, proteome biomarkers can help the follow up of AD progression over time and aid in setting personalized medical care, before the catastrophic consequences of dementia occurs. Research has focused on the identification of proteome biomarkers in cerebrospinal fluid (CSF) and plasma, which are discussed in the present review, but also in other matrices, as saliva and urine, revealing the high potentiality of proteomics approach and, at the same time, the difficulty to identify, for the different stages of the disease, sensitive and specific biomarkers clinically available.

Light is an electromagnetic radiation that has visible and invisible wavelength spectrum. The visible light can only be detected by the eyes through the optic pathways. With the presence of scalp, cranium and meninges, the brain is seen as being protected from direct exposure to light. For that reason, the brain can be viewed as a black body lying inside a black box. In physics, a black body tends to be in thermal equilibrium with its environment and can tightly regulate its temperature via thermodynamics principles. Therefore, a healthy brain inside a black box should not get exposed to light. On the contrary, photobiomodulation, a form of light therapy to the brain has been shown to have beneficial effects for some neurological conditions. The proposed underlying mechanisms are multiple. Herein we present our intraoperative findings of rapid electrocorticographic brainwave changes when the brain was shone directly with different wavelengths of light during awake brain surgery. Our findings provide literature proof on light’s ability to influence human brain energy and function. Our proposed mechanism for these rapid changes is the presence of plasma-like energy inside the brain which causes fast brain activities that are akin to lightning strikes.

Aims: Chronic coronary syndrome is associated with several risk factors, such as dyslipidemia and hypertension. AIP has been demonstrated to be a biochemical risk factor for coronary artery disease (CAD). This study aimed to determine whether AIP is an effective parameter for estimating obstructive CAD. Methods and Results: A total of 345 patients (mean age 62,2±10,3; 63% male) who underwent coronary angiography were included in this study. Obstructive CAD is defined as having one or more vessels with a stenosis of≥50%. Depending on the presence of obstructive CAD, all patients were divided into two groups. The AIP was significantly higher in the obstructive coronary artery group (AIP; 0,49±0,26 vs. 0,58±0,27, p=0,002). In univariate analysis, AIP was significantly associated with obstructive coronary artery disease [OD:3,74 (CI95% 1,62-8,64), P=0,020]. The AIP was further adjusted for confounding risk factors in three multivariate analysis models. Therefore, all three models showed a significant association. According to ROC analysis, 0.49 is the cut-off value for AIP, and a value above 0.49 indicates 50% coronary artery stenosis Conclusions: AIP may be used in the assessment of cardiovascular risk in patients with stable angina pectoris, and it may also be used to estimate obstructive CAD.

SiOx films, frequently derived from amino silane precursors, have found several applications with high added value. Although frequently used, the deposition of coatings from Tris(dimethyl amino)silane (TDMAS) has been reported to demand considerable amounts of energy, mainly due to the difficulty of oxidizing such compound. As it is well known, Plasma-enhanced atomic layer deposition (PEALD) is able to improve the oxidation efficiency even under low process temperatures. Owing to that, PEALD can be considered as a very promising technique for the deposition of SiOx coatings. In this work, it has been investigated the deposition of silicon oxide films using TDMAS at 150°C. It has been evaluated the effect of the plasma oxidation time (6 to 18 s) and of the atmosphere composition (pure O2 or O2+Ar) on the chemical structure, elemental composition and chemical bonding state of the films. Increasing the plasma oxidation time in pure O2 resulted in larger proportion of retained C (Si-CH3) whereas N was preserved in the structure (Si-N). on the other hand, the formation of SiOx films from TDMAS is favored in shorter oxidation times in O2 + Ar plasmas.

Polyimide (PI) films are widely used in electronic devices owing to their excellent mechanical and electrical properties and high thermal and chemical stabilities. In particular, PI films play an important role in flexible printed circuit boards (FPCBs). However, one challenge currently faced with their use is that the adhesives used in FPCBs cause a high dielectric loss in high-frequency applications. Therefore, it is envisioned that PI films with a low dielectric loss and Cu films can be used to prepare two-layer flexible copper clad laminates (FCCLs) without any adhesive. However, the preparation of ultra-thin FCCLs with no adhesives is difficult owing to the low peel strength between the PI films and Cu films. To address this technical challenge, an FCCL with no adhesive was prepared by high-power helicon wave plasma (HWP) treatment. The surface roughness of the PI film and the peel strength between the PI film and Cu film were measured. The experimental results showed that the surface roughness of the PI film increased by 40-65% and the PI film demonstrated improved adhesion (the peel strength was &gt;8.0 N/cm) with the Cu film following plasma treatment and Cu plating.

People with specific TREM2 gene variants are more prone to develop Alzheimer's disease (AD). The TREM2 receptor regulates the number of myeloid cells, phagocytosis, and the inflammatory response via interacting with apolipoproteins and amyloid. Higher TREM2 expression has been found to protect against AD. When TREM2 activity increases, the activity of genes involved in the activation of microglia cells decreases. This can improve the efficiency of phagocytosis. When TREM2 is highly expressed and the inflammasome is activated, the results are not always congruent. Therefore, this study aimed to discover how sTREM2 levels in CSF and plasma samples relate to other indices of AD pathology. We examined 98 AD plasma samples, 35 plasma samples of subjects with mild cognitive impairment (MCI), 11 healthy controls (HC) plasma samples, as well as 155 AD CSF samples, 90 MCI CSF samples, and 50 HC CSF samples. CSF sTREM2 levels were higher in the AD group than in the MCI and HC groups, in contrast to plasma sTREM2. This shows that CSF sTREM2 levels could be used to distinguish between healthy and AD patients. CSF sTREM2 levels were significantly correlated with neurofibrillary changes, cognitive decline, and inflammasome activity in AD patients. While our findings are consistent with previous research, future studies will need to include more patients and employ standardized methodological approaches to add CSF sTREM2 to the list of biomarkers for AD.

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

This study aimed to evaluate the effects of feeding spray-dried porcine plasma (SDPP) on the protection afforded by the BA71∆CD2 African swine fever virus (ASFV) vaccine prototype. Two groups of pigs ac-climated to diets without or with 8% SDPP were intranasally inoculated with 105 plaque forming units (PFU) of live attenuated ASFV strain BA71∆CD2 and three weeks later left in direct contact with pigs infected with the pandemic Georgia2007/01 ASFV strain. During the post-exposure (pe) period, 2/6 from the conventional diet group showed a transient peak rectal temperature >40.5ºC before day 20 pe and some tissue samples collected at 20 d pe from 5/6 were PCR+ for ASFV, albeit showing Ct values much higher than Trojan pigs. Interestingly, the SDPP group did not show fever, neither PCR+ in blood nor rectal swab at any time pe and none of the postmortem collected tissue samples were PCR+ for ASFV. Differential serum cytokine profiles among groups at vaccination, and a higher number of ASFV-specific IFNϒ-secreting T-cells in pigs fed with SDPP soon after the Georgia2007/01 encounter, confirmed the relevance of Th1-like responses in ASF pro-tection. We believe that our result show that nutritional interventions might contribute to improve future ASF vaccination strategies.

Tissue programmed death ligand-1 (PD-L1) protein expression is predictive of immune checkpoint inhibitor (ICI) benefit. However, tissue PD-L1 can be fraught with tissue acquisition and heterogeneity limitations. Plasma testing can overcome these limitations. However, the overall survival (OS) predictive benefit of plasma PD-L1 assays have not been well characterized. Patients with stage IV non-small cell lung cancer (NSCLC) and plasma cfRNA PD-L1 by PCR expression were identified and assessed for OS. 16 patients treated with front-line ICI-based regimens were assessed and represented a real-world patient population with over half with a performance status of 2 or greater. 10 contemporaneous patients at the same institution treated with chemotherapy alone were also identified and assessed. With a median follow-up of 33 months, median OS was 13 months with a 30% 3-year OS for the ICI treated patients compared to a median OS of 3 months and a 10% 3-year OS for those treated with chemotherapy alone. Comparative log-rank test p-value = 0.014 and a hazard ratio 0.376 (95%-CI 0.134-1.057). Plasma cfRNA PD-L1 was associated with a statistically significant survival benefit from ICI-based treatment compared to chemotherapy in the first line treatment of a real-world patient population of advanced NSCLC.

In this paper, we study the weak deflection angle using Gauss-Bonnet theorem and bounding greybody factor for electric and magnetic black holes in the background of nonlinear electrodynamics. Using Gibbons and Werner's approach, first we acquire the Gaussian optical curvature to use in Gauss-Bonnet theorem and calculate the bending angle for spherically symmetric electric and magnetic black holes in both non-plasma and plasma mediums in the weak field limits. Later, we calculate the rigorous bounds of the greybody factor for the given black holes. Furthermore, we look into the graphical behaviour of bending angles and greybody bounds at some specific values of multiple parameters as well as black holes charges. It is to be mention here that all the results for the electric and magnetic charged black holes solutions reduce into the Schwarzschild black hole solution in the absence of the black holes charges.

The objective of this paper is to analyze the weak deflection angle of Einstein-Gauss-Bonnet gravity in the presence of plasma medium. To attain our results, we implement the Gibbons and Werner approach and use the Gauss-Bonnet theorem to Einstein gravity to acquire the resulting deflection angle of photon's ray in the weak field limit. Moreover, we illustrate the behavior of plasma medium and non-plasma mediums on the deflection of photon's ray in the framework of Einstein-Gauss-Bonnet gravity. Similarly, we observe the graphical influences of deflection angle on Einstein-Gauss-Bonnet gravity with the consideration of both plasma and non-plasma mediums. Later, we observe the rigorous bounds phenomenon of the greybody factor in contact with Einstein-Gauss-Bonnet gravity and calculate the outcomes, analyze graphically for specific values of parameters.