Yogyakarta City is one of the big city which is located in Java Island, Indonesia. Yogyakarta City, including study area (Pleret Sub District), are very prone to earthquake hazards, because close to several active earthquake sources. For example, Sunda Megathrust which often generates a big earthquake which can affect the study area. The Sunda Megathrust extends from north to south and west to east along the Sumatra and Java Islands. Furthermore, an active normal fault called as Opak Fault pass through right in the middle of Study area and divides the study area into east and west zone. Recently, after the devastating earthquake in 2006, the population of the study area increases significantly. As a result, the housing demand is also increasing. However, due to the absence of earthquake building code in the study area, locals tend to build improper new houses. Furthermore, in some part of the mountainous area in the study area, there are some building found in unstable slopes area. Due to this condition, the multi-hazard and risk study needs to be done in Pleret. The increasing of population and improper houses in Pleret Sub-District can lead to amplify the impact. Thus, the main objective of this study is to assess the multi-hazards and risk of earthquake and other related secondary hazards such as ground amplification, liquefaction, and coseismic landslide. The method mainly utilised the geographic information system, remote sensing and was fit up by the outcrop study. The results show that the middle part of the study area has a complex geological structure. It was indicated by a lot of unchartered faults was found in the outcrops. Furthermore, the relatively prone areas to earthquake can be determined. In term of the coseismic landslide, the prone area to the coseismic landslide is located in the east part of the study area in the middle slope of Baturagung Escarpment. The highly potential area of liquefaction is dominated in the central part of the study area. In term of building collapsed probability, the result shows that the safest house based on statistical analysis is the residential house with the building attribute of wood structure, roof cast material, distance more than 15 km from the earthquake source, and located above the Nglanggran Formation. Finally, the multi-hazard and risk analysis show that the middle part of the study area is more vulnerable than the other part of Pleret Sub-District.

In response to the problem of no supporting equipment for the cultivation of Codonopsis in the hilly and mountainous areas of northwest China, a combined machine for transplanting outcrop of Codonopsis with micro ridge covered with film is designed. The key components of the prototype are analyzed and designed, and the structures and working parameters of the seedbed preparation device, seedling casting device, rotary tillage soil-covering device, film covering device, seedling head burial and film edge soil-covering device are determined. The transmission system scheme is established, and the working mechanism of the core components is analyzed. Field experiments show that when the target seedling spacing is 4.4cm and the machines moves forward at the speed of 0.1, 0.15, and 0.2m/s, the variation coefficient of planting spacing and the qualification rate of planting depth all meet the standard requirements. The qualified rate of planting posture and film side outcrop are greatly affected by the operating speed of the machine, and decrease with the increase of operating speed. When the operating speed reaches 0.1m/s, the average variation coefficient of planting spacing is 0.08%, the average qualified rate of planting depth, planting posture and film side outcrop is 95.83%, 94.17% and 93.33% respectively, which shows that the operating performance is better than that of the operating speed of 0.15m/s and 0.2m/s. This study provides new reference for the theoretical research and design of mechanized and automated transplanting machinery for Codonopsis seedlings.

Three-dimensional (3D) facies and petrophysical models were generated from previously published data of carbonate strata in the Dam Formation (eastern Saudi Arabia) to quantitatively investigate, describe, understand, model, and predict the permeability anisotropy of tidal flat carbonate within a sequence stratigraphic framework. The resulting 3D models were used to conduct fluid flow simulations to demonstrate how permeability anisotropy influences the production of hydrocarbons and ultimately affects decisions concerning future drilling in the exploration and development of carbonate reservoirs that have tidal flat strata. The constructed 3D facies model consists of four lithofacies associations, two of which were grain-dominated associations and two of which were mud-dominated associations. These lithofacies associations varied spatially in four reservoir zones (zones 1 to 4), which represent two fourth-order sequences in the uppermost part of the Dam Formation. Zones 1 and 3 consist of transgressive parasequences, and zones 2 and 4 consist of the regressive parasequences of these sequences. The 3D porosity and permeability models have a coherent match with the distribution of the lithofacies and the stratigraphic framework of the Dam Formation. The results suggested that the permeability anisotropy in zones 1 and 3 is controlled by the occurrence of the grain-dominated lithofacies associated with tidal flat channels. This lithofacies association overlies the sequence boundaries of sequences 1 and 3, forms reservoir bodies with relatively high permeability values, and is elongated perpendicular to the shoreline of the depositional environments. In contrast, permeability anisotropy in zones 2 and 4 is thought to be controlled by the occurrence of the grain-dominated lithofacies associated with the oolitic shoal. This lithofacies association overlies the maximum flooding surface of sequences 2 and 4, forms reservoir bodies with relatively high permeability values, and is elongated parallel to the shoreline of the depositional environments. Fluid flow simulation results suggested that the trend in hydrocarbon production from the constructed 3D models depends on permeability anisotropy in each reservoir zone. Thus, recognizing trends in permeability anisotropy, which might be predicted using sequences stratigraphy, could help to identify potential areas for future drilling.