This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Wind energy is becoming increasingly important as a renewable energy source due to its environmental and economic benefits. Wind turbines are key components in wind energy systems, and their performance is critical for efficient power generation. Wind turbine blades are the most critical components as they interact with the wind, and their design has a significant impact on the overall system performance. Therefore, it is essential to optimize the design of wind turbine blades to enhance their efficiency and reduce their costs. This paper presents an aero-structural optimization approach for wind turbine blade design. The optimization aims to maximize the torque generated by the blade while minimizing its mass. The optimization is implemented using DAFoam software for CFD simulation, TACS for FEM simulation, and Mphys under the OpenMDAO framework for fluid-structure interaction between the CFD and FEM. The optimization results show a 6.78% increase in torque and a 4.22% decrease in mass, which demonstrates the effectiveness of the proposed approach. Aerodynamic optimization focuses on maximizing the blade's torque by modifying the blade's shape. The optimization results show that the optimized blade generates more torque than the original blade design. Additionally, structural optimization aims to minimize the blade's mass while maintaining its structural integrity. This is achieved by adjusting the thickness of the blade's cross-section. The proposed aero-structural optimization approach presents an effective solution for the design optimization of wind turbine blades. The approach considers the interaction between the aerodynamic and structural aspects of the blade and optimizes them simultaneously. This leads to an optimized design that is efficient and cost-effective, which is crucial for the widespread adoption of wind energy systems. The results of this study highlight the importance of considering the interaction between the aerodynamic and structural aspects of wind turbine blades and the effectiveness of the proposed optimization approach in enhancing their performance.

Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

When using meta-heuristic optimization approaches for optimization, a large number of samples are required. In particular, when generating subgeneration, the utilization of existing samples is low and the number of individuals is high. Therefore, surrogate-based optimization has been developed, which greatly reduces the number of individuals in the subgeneration and the cost of optimization. In complex air supply scenarios, single-objective optimization results may not be comprehensive; therefore, this paper developed a double-objective air supply optimization method based on the Kriging surrogate model and Non-dominated Sorting Genetic Algorithms-II. And proposed the infill criteria based on clustering to advance the Pareto Frontier. The method was validated by an inverse prediction case, and in particular, the problems when based on 3D steady-state simulations were analyzed. The results showed that the method can quickly achieve an approximate prediction of the boundary conditions (when prediction were made based on experimental data, the number of simulations was 82 and the average error was 6.8%). Finally, the method was used to optimize the air supply parameters of a dual-aisle, single-row cabin. The Pareto set suggested that an airflow organization with dual circulation may be optimal.

This research demonstrates the optimization and production of biochar from barley husk (BH), corn cob (CC), and Agave salmiana leaves (AL) via pyrolysis in a muffle furnace. Taguchi experimental design (L9) was applied to conduct the experiments at different levels by altering four operating parameters. Carbonization temperature (300–500 ºC), carbonization time (30–90 min), precursor mass (2–5 g) and N₂ flow rate (100–200 cc/min) were the variables examined in this study. The effect of the parameters on the biochar yield was investigated, and the important parameters were identified employing analysis of variance (ANOVA). The optimum conditions for maximum biochar yield were: carbonization temperature of 400 ºC, carbonization time of 30 min, precursor mass of 2 g, and N₂ flow rate of 150 cc/min. The biochars produced under optimum conditions was characterized physically and chemically. Biochar yields of 19.75% for corn cob (CCB), 32.88% for barley husk (BHB), and 31.14% for agave leaves (ALB) were obtained.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

In view of the floating rectangular aerostatic guideway problem of low load capacity and stiffness, this paper puts forward a kind of closed rectangular aerostatic guideway and its optimized design. Firstly, the analytic calculation formula of a closed rectangular aerostatic guideway was deduced. The use of MATLAB software for the numerical simulation and the parameter influence analyses was carried out in terms of the gas supply pressure on load capacity and stiffness. A simulation model of the rectangular air bearing was also built using the Fluent software, and the model was used for simulation calculations. Secondly, the static performance of the rectangular air bearing was analyzed by analyzing the distribution position and number of orifices on its load capacity and stiffness. On this basis, the response surface optimization design method is used to analyze the variation law of the load capacity and stiffness of the air bearing under different restrictor structural parameters. Finally, the optimal design parameters for the rectangular air bearing are obtained. The simulation results show that the optimized rectangular air bearing designed in this paper has a good load capacity and stiffness of 644.58N and 63.405N N∙μm^(-1).

Over-capacity flight scheduling by commercial airlines due to the surging demand in recent years creates congestion and significant delays at major airports. This maximizing throughput attitude calls for tactical flight rescheduling to comply with airports’ capacity limitations and distribute the peak hour demand over the course of a day. Such displacements of flights may cause significant problems and costs for airlines and some cancellations or missed connections for the passengers. This paper presents an optimization model for flight rescheduling at a schedule-coordinated airport to minimize congestion and flight delays. The optimization model is used to make better scheduling intervention decisions considering the airport resource constraints and safety of operation. We have also developed a simulation method to replicate arrival and departure processes in such an airport. The simulation adheres to a first come first served (FCFS) discipline and enforces runway capacity constraints and minimum turnaround times. We compare the delays caused by an ad hoc FCFS operation with those obtained by the optimization model. Computational results from a case study demonstrate that a reduction of 40.7% and 61.6% in total delay times for the arrival and departure flights can be achieved by the optimization model. It also facilitates implementing a collaborative decision-making system for better coordination with commercial airlines.

Numerical optimization methods are widely used for designing turbomachinery components due to the cost and time savings they can provide. In the available literature, shape optimization of radial compressors is mainly focused on improving the impeller alone. However, it is a well-established knowledge that the volute plays a key role in the overall performance of the compressor. The aim of the present paper is to perform the adjoint-based optimization of a volute that is designed for the SRV2-O compressor. The CAD model is first created, using a parametrization of 33 design parameters. Then, a butterfly topology is applied to mesh the computational domain with a multi-block structured grid, and an elliptic smoothing procedure is then used to improve the quality of the fluid grid. A steady-state RANS CFD solver with Spalart-Allmaras turbulence model is used to solve the Navier-Stokes equations, and flow sensitivities are computed with an adjoint solver. The objective function consists in minimizing the loss coefficient of the volute. The optimization is performed to obtain an improved design with 14% losses reduction. Detailed flow and design analysis is carried out to highlight the loss reduction mechanisms followed by the optimizer. Finally, the compressor map of the full stage is compared between the baseline and the optimized volute through CFD simulations using a mixing plane interface. This research demonstrates the successful use of a gradient-based optimization technique to improve the volute of a radial compressor and opens the door towards optimizing simultaneously the wheel and the volute.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

The advantage of FPGAs lies in the ability to implement a fully hardware solution for interfacing with various input/output (I/O) devices. Each block can work in parallel with all the others, simplifying the satisfaction of timing constraints. However, this hardware utilization consumes FPGA resources that could otherwise be allocated to the primary project. An alternative involves employing a small "soft-core" processor implementing I/O in software. With the goal to design and evaluate a new tiny soft-core processor optimized for FPGA resources in I/O , a novel processor named Baby8 is developed. It is an 8-bit CISC soft-core processor optimized for reduced FPGA resources including program size for 8-bit applications. The number of instructions is not large but any instruction can access arbitrary memory locations. The performance and resource utilization of the newly designed processor are evaluated and compared with a variety of other soft-core processors. The results demonstrate its competitive performance, achieving an average maximum clock frequency of approximately 57 MHz and a power consumption of around 2mW. Furthermore, it conserves nearly half of the FPGA resources in implementation.

Dump design and scheduling are critical elements to effective mine planning, especially if several of them are required in large-scale open pit mines. Infrastructure capital and transportation costs are considerable from an early stage in the mining project, and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modelling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to model and optimize the design of a mine dump by minimizing the total haulage costs. The proposed methodology consists on: (i) Formulation of a dump model based on a system of equations relying on multiple relevant parameters; (ii) Solves by minimizing the total cost using linear programming and determines a ‘preliminary’ dump design; (iii) Through a series of iterations, modifies the ‘preliminary’ footprint by projecting it to the topography and creates the ultimate dump design. Finally, an example application for a waste rock dump illustrates this methodology.

Indoor Positioning Systems (IPSs) are designed to provide solutions for location-based services. Wireless local area network (WLAN)-based positioning systems are the most widespread around the globe and are commonly found to have a ready-to-use infrastructure composed mostly of access points (APs). They provide useful information on signal strength to be processed by adequate location algorithms, which are not always capable of achieving the desired localization error only by themselves. In this sense, this paper proposes a new method to improve the accuracy of IPSs by optimizing some of their most relevant infrastructure components. Included are the arrangement of APs over the environment, the number of reference points (RPs), and the number of samples per location estimation test. A simulation environment is also proposed, in which the impact of key influencing factors on system accuracy is analyzed. Finally, a case study is simulated to validate an optimal combination of design parameters and its compliance with the requirements of localization error and the limited number of access points. Our simulation results clearly show that the desired localization accuracy, which is set as a goal, can be achieved while maintaining the factors already mentioned at minimal levels, which decreases both system deployment costs and computational effort.

The COVID-19 pandemic has emphasized the crucial role of ventilation systems in mitigating cross-infections, especially in infectious disease hospitals. This study introduces a dual-design operation ventilation system that can operate under two sets of ventilation conditions for normal and epidemic times. A challenge is optimizing duct diameters for required airflow while maintaining hydraulic balance. We design a genetic algorithm with adaptive penalty factor, the velocity constraint and the improved crossover and mutation probability. The improved genetic algorithm is suitable for ventilation system networks, which can find a better air duct diameters combination to improve the hydraulic balance rate, and reduce the usage of air valves, resulting in efficient hydraulic balancing commissioning. Compared with the traditional genetic algorithm, it has a faster search speed and a better global search ability, which is effective for the optimal design of ventilation system networks.

This study is focused on an optimal sizing method based on genetic algorithms (GA) in order to design a high-performance photovoltaic system that would be installed in the Alioune Diop University of Bambey, Senegal. The multi-objective optimization allowed us to find a better trade- off between the Total Life Cycle cost (TLCC) and the Loss of Power Supply Probability (LPSP). The goal is to minimize the TLCC while maintaining a good satisfactory of the system with a desired LPSP, under certain constraints. The expressions of the TLCC and the LPSP are established according to the total photovoltaic energy and the battery capacity. The toolbox of Matlab software is used to implement the optimization problem with twelve blocks of the site and its different corresponding loads. The obtained results have led to a several combinations of the photovoltaic and battery capacities of which the best one is selected based on the lowest LPSP, that guaranteed a better load coverage during the night. The results of this proposed method are compared with intuitive method that has been firstly applied. For the block with the lowest load demand, the proposed optimization model leads to a reduction a reduction of 70% and 48% in the storage capacity and the TLCC respectively for a LPSP of 0.007 %.

The solved research problem is oriented to the implementation of advanced methods of component design and their sophisticated use in the ever-advancing additive manufacturing. Based on the stated objectives, the research was divided into several parts. Initially, the methods and principles of design in additive manufacturing were evaluated and investigated, from which the intent was subsequently defined and the DfAM method in the component design and development process was determined. The given design method, namely topology optimization (TO), was applied to multiple development and production cycles of additive manufacturing parts to validate the research conclusions. In this paper, the procedure for a specific part or component assembly is shown. By evaluating the developed design procedure using the TO method included in the design process, the conclusions are positive in terms of both time savings and properties of the designed part such as strength and weight parameters. The given findings need to be further developed by implementing on specific product lines for increasing the efficiency of the developed design methodology.

With the engineering system becoming more and more complex, the uncertainty factors have a more and more profound influence on the reliability and security of the engineering system. In recent years, Reliability-Based Design Optimization (RBDO) has been studied extensively in complex engineering system design. The research on reliability optimization design considering stochastic uncertainty has been comprehensive and widely used. However, the reliability optimization design considering mixed uncertainty has the disadvantages of large computation and imprecise convergence. This study proposes an RBDO method based on Particle Swarm Optimization (PSO) and Simulated Annealing (SA) to overcome this challenge. In the method, PSO is used to solve the most probable point, while SA has excellent global optimization capability to acquire the global optimal solution. Finally, three examples are given to illustrate the advantages of the proposed method.

Given the existing movable rotating plate type grading device for potatoes with a high safety factor and heavy mass, the body frame of the grading device and movable rotating plate were optimized and a lightweight design was carried out. Based on ANSYS Workbench 2022, the static analysis of the body frame before and after improvement was compared, and it was verified that the strength and deformation of the optimized body frame met the design requirements, and the weight of the optimized body frame was reduced by 32.3%. Based on the direct optimization module of ANSYS Workbench 2022, the plate length, width, and height were used as design variables for the lightweight design of the movable rotating plate. The MOGA algorithm was used to generate sixty design solutions, and the optimal combination of size parameters for the plate was 610 mm, 95mm, and1.2 mm. Compared with the whole grading device before optimization, the total mass was reduced by 22.86% after optimization. The research of this article provides a reference for the structural design and optimization analysis of potato grading devices.

Recently, 3D printing techniques gained much attention in solid dosage form production. Even though the methods are increasingly studied, there are still many challenges in establishing an accurate content of active ingredients in the final products. In the present study, new experimental design techniques and statistical software were developed to identify and optimize a formula to predict the mass of the tablet to be 3D printed before it actually is. The first step was to develop a virtual 3D object in the FreeCad Software, then, using a CURA slicer software, the G-code Format was obtained. The tablets were printed using a Cartesian 3D printer based on the generated data. Finally, adapting the object sequencing mode, a predicted drug mass value was obtained. As expected, the oblong tablet's scaling directly influences its mass. The software generates a correlation coefficient (r) of 0.84, confirming the directly proportional relationship between scaling and tablet weight. However, the r values progressively decreased, indicating a poor correlation between tablet weight and other factors: infill density percent (r = 0.403) and wall thickness (r = 0.185). After repeating the 3D printing with the values ​​suggested by the software, tablets with a practical value of 1066 mg were obtained. Considering that the confidence interval calculated is [834.95—1165.05] and the experimental value is 1066 mg, it can be certified that the proposed model is valid.

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

Since large power transformers are custom-made, and their design process is a labor-intensive task, their design process is split into different parts. In tendering, the price calculation is based on the preliminary design of the transformer. Due to the complexity of this task, it belongs to the most general branch of discrete, non-linear mathematical optimization problems. Most of the published algorithms are using a copper filling factor based winding model to calculate the main dimensions of the transformer during this first, preliminary design step. Therefore, these cost optimization methods are not considering the detailed winding layout and the conductor dimensions. However, the knowledge of the exact conductor dimensions is essential to calculate the thermal behaviour of the windings and make a more accurate stray loss calculation. The paper presents a novel, evolutionary algorithm-based transformer optimization method which can determine the optimal conductor shape for the windings during this examined preliminary design stage. The accuracy of the presented FEM method was tested on an existing transformer design. Then the results of the proposed optimization method have been compared with a validated transformer design optimization algorithm.

Advancement in physics often results from analyzing numerical data and then creating a theoretical model that can explain and predict those data. In the field of lens design, the reverse is true: longstanding theoretical understanding is being overtaken by more powerful numerical methods.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

This paper introduces a new rotor design for the easy insertion and removal of the rotor windings. The shape of the rotor is optimized based on surrogate method in order to achieve the lowest power loss under the maximum power output. The performance of the new rotor is examined in 2-D finite element software and validated by experiments. This rotor shows good potentials for reducing the maintenance and repair costs of synchronous machines, making it suitable for manufacturers within the mass production markets such as gen-sets, steam turbines, wind power generators and hybrid electric vehicles.

This research endeavors to illuminate the path toward efficient and optimized propeller design by delving into the realm of aerodynamics. Propellers, as vital mechanical marvels, constitute the core of numerous propulsion systems, spanning from aircraft and marine vessels to wind turbines. The pursuit of enhanced propeller efficiency and performance holds paramount importance in industries where propulsion assumes a critical role, underscoring the indispensable need for a profound understanding of aerodynamics. Through meticulously crafted theoretical insights and their practical applications, this study embarks on a journey into the fascinating realm of propeller aerodynamics. While the paper primarily addresses the aerodynamic aspects of propeller design and optimization, it serves as a foundational guide for those seeking to comprehend the intricacies of propeller engineering.The research journey commences with an in-depth exploration of the fundamental principles governing propeller performance. It unveils the intricate dynamics of airflow surrounding propeller blades, shedding light on their proficiency in generating thrust, lift, and torque. The bedrock of the theoretical insights is a comprehensive analysis encompassing airfoil profiles, blade geometry, and the underlying principles of blade element theory. In navigating the ensuing pages, the study embarks on the task of demystifying the intricate methods and calculations that propel the design and optimization of propellers. Leveraging cutting-edge methodologies, the research systematically assesses the aerodynamic characteristics of propellers across various operational conditions. These invaluable insights empower the tailoring of propeller designs with precision, aligning them seamlessly with specific performance objectives. The aim is not only to impart a comprehensive understanding of propeller aerodynamics but also to provide actionable insights for engineers and researchers striving to enhance propeller efficiency. This research endeavor serves as a guiding light for both propeller enthusiasts and professionals alike. It not only enriches the broader discourse on propeller technology but also equips readers with the requisite knowledge and tools to embark on their own quests for optimized propeller design. As propulsion technologies continue their evolution, the steadfast principles elucidated herein will persist, guiding future innovations and advancements in the realm of propeller engineering. This paper serves as a profound resource, offering new researchers a comprehensive understanding of propellers and their intricate design processes.

Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

Building facade design plays an essential role in enhancing energy efficiency and reducing environmental impact in high-performance building design. Balancing the conflicts among various building facade design parameters to satisfy different optimization objectives constitutes a highly complex optimization problem. The rapidly increasing number of studies demonstrates a significant interest in implementing multi-objective optimization methods to tackle building facade optimization problems. This study conducts a systematic review of optimization methods for building facade optimization (BFO). The optimization objectives and design variables are categorized based on their characteristics. The efficiency and effectiveness of optimization algorithms in addressing BFO problems are compared. Building optimization techniques and tools are showcased, along with their functions and limitations. Key findings highlight the robust feasibility and effectiveness of optimization algorithms, methods, and techniques in resolving a diverse range of BFO challenges. The limitations, challenges, and future potential of these methods are summarized and proposed.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

The multi-objective optimization design of hydraulic climbing mechanism (the core mechanism of gantry crane) was realized by using the method of combining central composite design (CCD), Kriging and multi-objective genetic algorithm (MOGA). Firstly, the hydraulic climbing mechanism model was established and the appropriate design variables were selected. The mass, maximum deformation and maximum equivalent stress of the hydraulic climbing mechanism was taken as the optimization objectives. Through the comparative analysis of the parameters of wedge block, anchor block, anchor plate、baffle, the parameters that have the greatest impact on the optimization objectives are selected as geometric constraints. Then, according to the results of experimental design, Kriging model was used to establish the response surface optimization model of objective function. Finally, the optimal results were obtained by using MOGA method. The experimental results show that the optimization strategy is reliable, and the mass of the optimized model is reduced by 10.28%. While meeting the actual production requirements, the lightweight design of the hydraulic climbing mechanism is realized, which saves the design cost and improves the material utilization rate.

The beautiful and stable posture is essential for ballet. Especially the pirouette which dancers balance themselves on their one leg is one of the most impressive postures. During the pirouette motion, loads from the rotation and the body weight are concentrated to the one leg. Proper ballet shoes can reduce the muscle burden and improve the stability. Four types of shoes; bare feet, running shoes, pointe shoes, and dance sneakers are analyzed. The motion capture system and SIMM are used for the analysis of muscle burden and stability during pirouette. The major 6 muscles in the leg (beceps femoris long head, beceps femoris short head, soleus, rectus femoris, gastrocnemius medialis, and gastrocnemius lateralis) are analyzed, and the effect of rotating velocity is considered. Dance sneakers are outstanding for improving the stability and lessening the muscle burdens in all conditions for beginners. That comes from the design feature of the divided shoe soles and protecting the ankle of the axis leg. With the results and analysis, the direction for design optimization of ballet shoes is suggested. Consequently, this research is about the verification of sports equipment using computer simulation with the musculoskeletal model from a scientific viewpoint of biomechanics.

Digital-Radio-Frequency-Memory (DRFM) has emerged as an advanced technique to achieve diverse jamming signals, due to its capability of intercepting waveforms within a short time. Multiple-Input Multiple-Output (MIMO) radars can transmit agile orthogonal waveform sets for different pulses to combat the DRFM-based jamming, where any two groups of waveform sets are also orthogonal. In order to design multiple groups of orthogonal waveform sets at the same time, this article formulates a group orthogonal waveforms optimal design model, whose objec-tive function is the weighted sum of the intra- and inter-group orthogonal performances metrics. To solve this optimization problem, this article proposes a group orthogonal waveforms design algorithm. Based on a primal-dual type method and proper relaxations, the proposed algorithm transforms the original problem into a series of simple sub-problems. Numerical results demonstrate that the proposed algorithm has the ability to balance the intra- and inter-group orthogonal performances by adjusting the weighting factors, which is not available using other state-of-the-art orthogonal waveform design algorithms.

The present work sets out the evaluation of composite laminates through optimization objective functions. Genetic Algorithms (GA), as well as Simulated Annealing (SA), were performed in order to determine the optimal ply orientations of a fiber-reinforced polymer laminate for three given load cases: 1) in-plane loads, 2) combined moments, and 3) in-plane loads and combined moments. It searches the optimal orientation layup, which fulfills at the same time both the maximum strain criterion and the Tsai-Wu failure criterion. Construction of an objective function based on the strains and the stresses involves a minimization process to deformations and a maximization of the safety factor. For the first load case, the initial solution is [±45/0/90/±45]s, and the best solution is [(45/135)2/452]s. For the second load case, [-45/45/45/-45/0/90]s is the initial layup sequence, then the best solution obtained is [(45/-45)2/452]s, where plies at 0° and 90º are not necessary even when axial loads are applied. For the third study case, the original layup sequence is [0/45/-45/45/0/90]s; meanwhile, the best solution calculated is [21/24/145/140/45/49]s. An interesting observation is that each pair of layers has a 5º gap. The simulations show that the qualitative results from the GA are better than the SA, but with a significantly higher computational cost. These kinds of computational tools are expected to be used as a reference guide for an optimal fiber configuration with respect to the common orientations used when composite laminates are designed for a structural application.

Desalinators are traditionally driven by fossil-fuels but in order to avoid greenhouse emissions, renewable energy must be used. In this paper, a coupling between multi-stage flash distillation apparatus and a parabolic trough solar collector is analyzed. The purpose of this study is to determine the economic feasibility of the system, considering four cities of Saudi Arabia and three different potable water productions. To avoid solar energy intermittency and unavailability at night, thermal storage is implemented. Whereas other researchers made parametric analyses, in this paper, the authors developed a mathematical program which was optimized with the help of GAMS software, where the capital cost of the plant was the objective function. After that, a life cycle cost analysis was carried out for each scenario. Depending on the region and water production, the costs of drinking water vary from 2.26 to 3.93 US$/m³, and from 7440 to 23825 tons of carbon dioxide emissions are avoided. As a consequence of the approach used, low costs are obtained; even though no auxiliary heater is implemented and the lowest irradiance conditions are considered. The results of this study reflect that the proposed process is competitive with respect to the traditional one.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

The concept of geostationary VHTS (Very High Throughput Satellites) is based on multibeam coverage with intensive frequency and polarization reuse in addition to the use of larger bandwidths in the feeder links, in order to provide high capacity satellite links at a reduced cost per Gbps in orbit. The dimensioning and design of satellite networks based on VHTS imposes the analysis of multiple trade-offs to achieve an optimal solution in terms of cost, capacity and figure of merit of the user terminal. In this paper, we propose a new method for sizing VHTS satellite networks based on an analytical expression of the forward link CINR (Carrier-to-Interference-plus-Noise Ratio) that is used to evaluate the trade-off of different combinations of system parameters. The proposed method considers both technical and commercial requirements as inputs including the constraints to achieve the optimum solution in terms of the user G/T, the number of beams and the system cost. The cost model includes both satellite and ground segments. Exemplary results are presented with feeder links using Q/V bands, DVB-S2X and transmission methods based on CCM and VCM (Constant and Variable Coding and Modulation, respectively) in two scenarios with different service areas.

In this study, a multiobjective, multiperiod, global optimization for design, sizing and dispatch of an islanded, hybrid microgrid was performed using a model built in MATLAB. The system was simulated over one year for sizing and over one day for dispatch, both using hourly time steps. The model minimized lifecycle levelized costs, emissions, lost load and dumped power while maximizing penetration of clean, renewable sources in the microgrid. This found optimal capacities of the renewable, energy storage and backup generation components which provide the best combination of affordability, sustainability, reliability and efficiency. After experimenting with several global solvers, it was determined that particle swarm optimization is most well-suited to solving the sizing optimization problem. The PV-wind microgrid using Li-ion batteries along with diesel engines was found to perform best among all the combinations considered. It was found that in spite of including additional objectives, monetary costs are the primary driver while allocating generation capacity between different renewable sources like wind versus solar PV. Furthermore, the sizing of PV, wind and battery storage depends strongly on the rating of the standby distributed generator, mainly due to reliability consideration. Generating Pareto-optimal sets revealed interesting relationships between different input variables (i.e. PV, wind and battery capacities) as well as trade-offs that arise while pursuing different objectives. Pursuing cost-minimization alone may lead to sub-optimal outcomes in terms of environmental impact, reliability and excess energy production. A sensitivity analysis was also conducted to understand the effects of various parameters like fuel price and energy storage costs on the optimal system's design and operation. Such accurate sizing programs help reduce the extent of oversizing of sub-systems during the design and planning stage, which is usually needed to achieve high reliability with distributed and decentralized energy systems like off-grid microgrids. This reduces the upfront capital investment needed to build the system, making clean electricity access affordable in the short term. The economic-environmental dispatch produced day-ahead scheduling strategies to meet the above mentioned objectives. The system was found to be relatively robust to short-term uncertainties and disturbances in renewable generation and load, although this does cause sub-optimal performance due to increased reliance on fossil fuels. It was found that dispatching of the batteries and backup generators is most critical in minimizing impacts of such events. However, the response to longer-term disturbances still remains to be assessed. The study also includes a comprehensive literature review of tools available for microgrid design as well as different optimization algorithms that have been used to solve microgrid sizing, dispatch and scheduling problems. Additionally, an overview is provided of various control strategies that can be used to improve robustness and resiliency of microgrids.

The study aims to analyze the characteristic parameters of rooftop photovoltaic (PV) power generation on industrial plant buildings in the Ningxia region of China, in order to evaluate the impact of passive design characteristic parameters on the benefits of PV power generation and determine the degree of impact of different passive design characteristic parameters. The methodology involves analyzing the characteristics of existing industrial plant buildings in Ningxia, China, and conducting a series of regional studies on the parameters of plant PV power generation influencing factors. The simulation results revealed that five features, including roof form, PV panel laying pattern, PV panel laying area, azimuth angle, and PV module material, have a significant impact on PV power generation benefits of industrial plant buildings.The study further uses MATLAB 2022b to build a backpropagation neural network model with 5 neurons in the implicit layer to predict the PV power generation benefits. The model calculates the whole-life cycle power generation benefits and the whole-life cycle reduction of carbon emissions as output data. Finally, the Mean Impact Value (MIV) method is employed to select the feature parameter values one by one within their range, and the passive design feature parameters that have the greatest influence on the prediction results are identified as the PV panel laying method, the PV panel tilt angle, and the PV material parameters, respectively.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

The market for microfluidic chips is experiencing significant growth; however, their development is hindered by a complex design process and low efficiency. Enhancing microfluidic chips’ design quality and efficiency has emerged as an integral approach to foster their advancement. Currently, the existing structural design schemes lack careful consideration regarding the impact of chip area, microchannel length, and the number of intersections on chip design. This inadequacy leads to redundant chip structures resulting from the separation of layout and wiring design. This study proposes a structural optimization method for microfluidic chips to address these issues utilizing a simulated annealing algorithm. The simulated annealing algorithm generates an initial solution in advance using the fast sequence pair algorithm. Subsequently, an improved simulated annealing algorithm is employed to obtain the optimal solution for the device layout. During the wiring stage, an advanced wiring method is used to designate the high wiring area, thereby increasing the success rate of microfluidic chip wiring. Furthermore, the connection between layout and routing is reinforced through an improved layout adjustment method, which reduces the length of microchannels and the number of intersections. Finally, the effectiveness of the structural optimization approach is validated through six sets of test cases, successfully achieving the objective of enhancing the design quality of microfluidic chips.

In today's human society, diesel generators (DGs) are highly applied into the human energy and electricity supply system due to its technical, operational and economic advantages. This paper proposes an intelligent nonlinear $H_2/H_{\infty}$ robust controller based on the chaos particle swarm gravity search optimization algorithm (CPSOGSA), which controls the speed and excitation of a DG. In this method, firstly, establish the nonlinear mathematical model of the DG and then design the nonlinear $H_2/H_{\infty}$ robust controller based on this. The direct feedback linearization and the $H_2/H_{\infty}$ robust control theory are combined and applied. Based on the design of the integrated controller for DG speed and excitation, the system's performance requirements are transformed into a standard robust $H_2/H_{\infty}$ control problem. The parameters of the proposed solution controller are optimized by using the proposed CPSOGSA. The introduction of CPSOGSA completes the design of an intelligent nonlinear $H_2/H_{\infty}$ robust controller for DG. The simulation is implemented in MATLAB/Simulink, and the results are compared with the PID control method. The obtained results prove that the proposed method can effectively improve the dynamic accuracy of the system and the ability to suppress disturbances and improve the stability of the system.

Renewable energy sources (RES) will play a crucial role in future sustainable energy systems. In scenarios analyzing future energy system designs, a detailed spatial and temporal representation of renewable-based electricity generation is essential. For this, sufficiently representative weather data are required. Most analyses performed in this context use the historical data of either one specific reference year or an aggregation of multiple years. In contrast, this study analyzes the impact of different weather years based on historical weather data from 1980 through 2015 in accordance with the design of an exemplary future energy system. This exemplary energy system consists of on- and offshore wind energy for power-to-hydrogen via electrolysis, including hydrogen pipeline transport for most southwestern European countries. The assumed hydrogen demand for transportation needs represents a hypothetical future market penetration for fuel cell-electric vehicles of 75%. An optimization framework is used in order to evaluate the resulting system design with the objective function of minimizing the total annual cost (TAC) of the system. For each historical weather year, the applied optimization model determines the required capacities and operation of wind power plants, electrolyzers, storage technologies and hydrogen pipelines to meet the assumed future hydrogen demand in a highly spatially- and temporally-detailed manner, as well as the TAC of the system. Following that, the results of every individual year are compared in terms of installed capacities, overall electricity generation and connection to the transmission network, as well as the cost of these components within each region. The results reveal how sensitive the final design of the exemplary system is to the choice of the weather year. For example, the TAC of the system changes by up to 20% across two consecutive weather years. Furthermore, significant variation in the optimization results regarding installed capacities per region with respect to the choice of weather years can be observed.

In this paper, we propose an efficient numerical computation method of reduced-order controller design for linear time-invariant systems. The design problem is described by linear matrix inequalities (LMIs) with a rank constraint on a structured matrix, due to which the problem is NP-hard. Instead of the heuristic method that approximates the matrix rank by the nuclear norm, we propose a numerical projection onto the rank-constrained set based on the alternating direction method of multipliers (ADMM). Then the controller is obtained by alternating projection between the rank-constrained set and the LMI set. We show the effectiveness of the proposed method compared with existing heuristic methods, by using 95 benchmark models from the COMPLeib library.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

To realize structural vibration control,a two parameters H2 optimization design was proposed to optimize the tuning ratio and damping ratio for electromagnetic tuned mass damper (EMTMD). The control effect of this two parameters optimization design is better than that of classical tuned mass damper (TMD).For this two parameters optimization,the most important thing is that the inductance of the coil can be set very small and the external load resistance can be positive ,which can avoid the use of complex negative impedance circuit. If Ref.[6] were designed according to the H2 optimization of two parameters, the EMTMD can be used for multi-modal vibration control of structures without connecting negative inductance and negative resistance spontaneously.

This work explores an additive-manufacturing-enabled combination-of-function approach for design of modular products. AM technologies allow the design and manufacturing of nearly free-form geometry, which can be used to create more complex, multi-function or multi-feature parts. The approach presented here replaces sub-assemblies within a modular product or system with more complex single parts that are designed and manufactured using AM technologies. This approach can increase the reliability of systems and products by reducing the number of interfaces, as well as allowing the optimization of the more complex parts during the design. The smaller part count and the ability of users to replace or upgrade the system or product parts on-demand should reduce user risk, life-cycle costs, and prevent obsolescence for the user of many systems. This study presents a detailed review on the current state-of-the-art in modular product design in order to demonstrate the place, need and usefulness of this AM-enabled method for systems and products that could benefit from it. A detailed case study is developed and presented to demonstrate the concepts.

In recent years, unquestionable warnings like the negative impacts of CO2 emissions, the necessity of utilizing sustainable energy sources, and the rising demand for municipal electrification have been issued. In this study, by incorporating two significant assumptions, such as electricity production in close proximity to the business location and only renewable energy resource usage, a modest off-grid hybrid energy system is designed. To construct the system, a number of elements such as wind generators (WG), photovoltaic arrays (PV), battery banks, and bi-directional converters are taken into account. Moreover, a real case in Malmö, Sweden, is considered. To optimize the system, a bi-objective problem is developed, and it is solved by proposing a particle swarm optimization (PSO) approach to provide the load requirements (with a maximum allowance of 0.1% unmet) for a nearby supermarket (approximately 1000 m2). Moreover, to verify the obtained results, the developed system is simulated using HOMER Pro software, and the results are compared and discussed. The contribution of this study is to provide off-grid or local clients around the world with a dependable and affordable option by minimizing both the baseline cost of energy and the net current expenditure in the desired system. The best-obtained results by the proposed PSO offered 160 PVs, 5 WGs, and 350 batteries, respectively, while the best solution found by the simulation method was using 384 PVs, 5 WGs, and 189 batteries for the considered off-grid system.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

Ice covering on overhead transmission lines would cause damage to transmission system and long-term power outage. Among various de-icing devices, modular multilevel converter (MMC) based DC de-icer (MMC-DDI) is recognized as a promising solution due to its excellent technical performance. Its principle feasibility has been well studied, but few literature discuss its economy or hardware optimization, thus the designed MMC-DDI for high voltage transmission lines is usually too large and too expensive for engineering applications. To fill this gap, this paper presents a quantitative analysis on the converter characteristics of MMC-DDI, and calculates the minimal converter rating and its influencing factors. It reals that, for a given de-icing requirement, the converter rating varies greatly with its AC-side voltage. Then an optimization configuration is proposed to reduce the converter rating and improve its economy. The proposed configuration is verified in a MMC-DDI for a 500kV transmission line as a case study. The result shows, in the case of outputting same de-icing characteristics, the optimized converter rating is reduced from 151 MVA to 68 MVA, and total cost of MMC-DDI is reduced by 48%. This analysis and conclusion are conductive to the optimized design of multilevel DC de-icer, then to its engineering application.

Silicon anodes have been considered one of the most promising anode candidates for the next generation of high-energy density lithium-ion batteries due to the high theoretical specific capacity (4200 mAh g-1) of Si. However, high lithiation capacity endows silicon anodes with severe volume expansion effects during the charge/discharge cycling. The repeated volume expansions not only lead to the pulverization of silicon particles and the separation of electrode materials from the current collector, but also brings rupture/formation of solid electrolyte interface (SEI) and also continuous electrolyte consumption, which seriously hinders the commercial application of silicon anodes. Structural design and optimization is the key to improving the electrochemical performances of silicon anodes, which has attracted wide attention and research in recent years. This paper mainly summarizes and compares the latest research progress for the structural design and optimization of silicon anodes.

Background: With the trend of intelligent display, the interface design of in-vehicle HUD is an expanding research field; Methods: To solve the subjectivity and uncertainty in the optimization of HUD interface design schemes, this paper proposed a hybrid scheme evaluation and optimization method based on entropy weight and VIKOR. The entropy weight method was used to reduce the subjectivity the decision-maker's weighting and obtain the objective weight of each indicator; The VIKOR method was used to obtain the best ranking of alternative schemes, and then the optimal interface design scheme was selected; Results: The evaluation of in-vehicle HUD interface design schemes were taken as an example for verification and calculation. The results showed that this method considers the subjectivity and uncertainty of the decision-making process in the optimization of design scheme, which can effectively improve the objectivity and accuracy of the evaluation results, and provide a reference for designers to optimize interface design schemes.

Bifacial PV modules have become the pervasive choice for utility-scale solar photovoltaic (PV) installations. Understanding bifacial PV performance for commercial deployments is, therefore, critically important. Although there have been studies on the modeling of Bifacial PV performance, to the best of our knowledge, the comprehensive integration of racking and mounting geometry for Bifacial PV performance simulation is yet to be reported. In this work, we modeled the racking and mounting geometry for a field-deployed operational PV array. We then applied optical ray-trace simulation to study the impact of those structures on array performance. The study reveals that the support structures have a considerable impact on the rear surface irradiance and overall bifacial PV performance, amounting to as much as 30% shading in certain situations. The work analyzes the impact of installation parameters such as tilt, height, and row spacing on the bifacial PV array’s performance. Thus, a novel holistic approach to studying the sensitivity of various installation parameters’ impact on bifacial PV array performance, with the racking and mounting structure’s geometry integrated, has been demonstrated through the work. This knowledge and its practice enables site-specific design optimization for utility-scale bifacial solar PV arrays and synergistic PV applications such as agrivoltaics and carports, where maximizing power generation is not necessarily the sole objective.

Magnetic levitation vibration isolation platform are essential for testing space telescopes. This paper presents the design of a Large Air-Gap Voice Coil Motor (LAG-VCM) specifically for use in such platforms. The electromagnetic design of the voice coil motor begins with the Equivalent Magnetic Circuit Method, followed by the analysis and optimization of the motor design using Finite Element Analysis (FEA). Subsequently, a prototype was constructed and tested. The test results confirm that the prototype meets the design specifications and requirements.

The oxidative coupling of methane (OCM) to produce ethane and ethylene (C2 compounds) as platform chemicals involves complex chemistry with reactions both in the gas phase and on the catalyst surface, resulting in a distribution of products at the expense of C2 selectivity. This work uses experimental data from a variety of mixed metal oxides on supports at different reaction conditions (temperature, contact time, and reactant flow rates) to train a random forest regressor that predicts methane conversion and C2 selectivity (key performance indicators (KPIs)), and deploys it to locate optimal conditions that maximize C2 yield for a catalyst. Investigating the regressor interpretability via feature importance reveals that the choice of metals and support are crucial to C2 selectivity predictions, while the predictions of methane conversion are driven by the reaction conditions. The machine learning (ML) regressor is used as a surrogate to develop performance curves for each of the catalysts via a multi-objective optimization routine that seeks to maximize the KPIs in the decision space of reaction conditions, is seen to locate optimal conditions at which the maximum C2 yields for catalysts are predicted to be 15%, higher on average. Analyzing the catalysts in the space of their performance curves with respect to a popular OCM catalyst, Mn-Na2WO4/SiO2, reveals distinct patterns based on intrinsic properties of metals and supports. Further, the decision space with catalyst descriptors and reaction conditions is optimized for high C2 yields using the ML surrogate, in a static multi-objective optimization routine, and an adaptive Bayesian routine, where the latter was found to have a wider field focus in proposing catalyst formulations and conditions. Transition metal oxides on a variety of supports were proposed but not their lanthanide oxide counterparts.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

Structural design optimization (SDO) plays a pivotal role in enhancing various aspects of construction projects, including design quality, cost-efficiency, safety, and structural reliability. Recent endeavors in academia and industry have sought to harness the potential of Building Information Modeling (BIM) and optimization algorithms to optimize SDO and improve design outcomes. This review paper aims to synthesize these efforts, shedding light on how SDO contributes to project coordination. Furthermore, the integration of sustainability considerations and the application of innovative technologies and optimization algorithms in SDO necessitate more interactive early-stage collaboration among project stakeholders. This study offers a comprehensive exploration of contemporary research in integrated SDO employing BIM and optimization algorithms. It commences with an exploratory investigation, employing both qualitative and quantitative analysis techniques following the PRISMA systematic review methodology. Subsequently, an open-ended opinion survey was conducted among construction industry professionals in Europe. This survey yields valuable insights into the coordination challenges and potential solutions arising from technological shifts and interoperability concerns associated with widespread SDO implementation. These preliminary steps of systematic review and industry survey furnish a robust knowledge foundation, enabling the proposal of an intelligent framework for automating early-stage sustainable structural design optimization (ESSDO) within the construction sector. The framework ESSDO addresses the challenges of fragmented collaboration between architects and structural engineers. This proposed framework seamlessly integrates with the BIM platform, i.e., Autodesk Revit for architects. It extracts crucial architectural data and transfers it to the structural design and analysis platform, i.e., Autodesk Robot Structural Analysis (RSA), for structural engineers via the visual programming tool Dynamo. Once the optimization occurs, optimal outcomes are visualized within BIM environments. This visualization elevates interactive collaborations between architects and engineers, facilitating automation throughout the workflow and smoother information exchange.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

Interior permanent magnets motors are widely used in applications requiring high power den-sity and high efficiency due to their high torque generating capabilities. Recently, given the re-cent price fluctuations and unstable supply of rare-earth permanent magnets, alternative config-urations with reduced use of permanent magnets are being sought. Among the various candi-dates related to this, the consequent-pole type rotor structure can halve the number of perma-nent magnets used compared with conventional structures. However, in the no-load analysis, the waveform of the back electromotive force becomes asymmetric, generating a harmonic component. As a result, there is a disadvantage that the torque ripple increases. To overcome these shortcomings, we propose a novel rotor structure that applies a consequent-pole structure to an embedded permanent-magnet motor structure, wherein a number of permanent magnets are arranged in a flared structure to constitute a single polarity. In the proposed flared-structured magnet arrangement, it is possible to adjust the angle of the permanent magnet and the polar angle to mitigate the asymmetry of the back EMF waveform. The proposed struc-ture was optimized with a genetic algorithm and a prototype of the optimal model was con-structed and experimentally evaluated to verify its validity. Finally, the performance improve-ment and validity of the proposed structure were verified by comparing the analysis results of the optimal model with the experimental results.

Multiphase systems are important in minerals processing, and usually include solid-solid and solid-fluid systems. Examples of operations in multiphase systems include flotation, dewatering, and magnetic separation, among several other unit operations. In this paper, the current trends in the process system engineering tasks of modeling, design, and optimization, in multiphase systems, are analyzed. Different scales of size and time are included, and therefore the analysis includes modeling at the molecular level and unit operation level, and the application of optimization for the design of a plant. New strategies for the modeling and optimization of multiphase systems are also included, with a strong focus on the application of artificial intelligence (AI) and the combination of experimentation and modeling with response surface methodology (RSM). The paper finishes with tools to study the uncertainty, both epistemic and stochastic, which is present in all mineral processing operations. It is shown that all these areas are very active and can help to understand, operate, design, and optimize mineral processing that involves multiphase systems.

In the Formula Student Racing Car, the anti-deformation ability of the frame will affect the four-wheel positioning parameters of the racing car, and then affect the handling and stability performance of the racing car. The quality of the frame directly determines the power and economy of the racing car, so the performance of the frame is very important to the performance of the race. In order to improve the performance of the frame and reduce the total weight of the frame, the research on the lightweight design of the frame is particularly important. In this paper, based on the variable density method, the global topology optimization of the frame is carried out to obtain the distribution of the frame material, realize the efficient use of the material, and improve the torsional stiffness of the frame. Based on the adjoint variable method, the sensitivity analysis of the frame is carried out. According to the sensitivity analysis results, the size of the frame is optimized. The total mass of the frame is reduced by 12.8 %, and the performance of the maximum displacement and maximum stress is improved. The lightweight design of the frame is realized as a whole.

In this paper, we consider a reconfigurable intelligent surface (RIS)-assisted integrated satellite-high altitude platform-terrestrial networks (IS-HAP-TNs) that can improve network performance by exploiting HAP's stability and RIS's reflection. Specifically, the reflector RIS is installed on the side of HAP to reflect signals from the multiple ground user equipments (UEs) to the satellite. To aim at maximising system sum rate, we jointly optimize the transmit beamforming matrix at the ground UEs and RIS phase shift matrix. Due to the limitation of the unit modulus of the RIS reflective elements constraint, the combinatorial optimization problem is difficult to tackle it effectively by traditional solving methods. Based on this, this paper studies deep reinforcement learning (DRL) algorithm to achieve online decision making for this joint optimization problem. In addition, it is verified through simulation experiments that the proposed DRL algorithm outperforms the standard scheme in terms of system performance and execution time, and higher computing speed, making real-time decision making truly feasible。

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

Hybrid renewable energy systems (HRES), complemented by pumped hydropower storage (PHS), have become increasingly popular amidst the increase of renewable energy penetration. This con-figuration is even more prosperous in remote regions that are typically not connected to the mainland power grid, where the energy independence challenge intensifies. This research focuses on the design of such systems, from the perspective of establishing an optimal mix of renewable sources that takes advantage of their complementarities and synergies, combined with the versatility of PHS. However, this design is subject to substantial complexities, due to the multiple objectives and constraints to fulfill, on the one hand, and the inherent uncertainties as well, that span over all underlying processes, i.e., external, and internal. In this vein, we utilize a proposed HRES layout for the Aegean Island of Sifnos, Greece, to develop and evaluate a comprehensive simulation-optimization scheme in deterministic and, eventually, stochastic setting, revealing the design problem under the umbrella of uncertainty. In particular, we account for three major uncertain elements, namely the wind velocity (natural process), the energy demand (anthropogenic process), and the wind-to-power conversion (internal process, expressed in terms of a probabilistic power curve). Emphasis is also given to the decision-making procedure, which requires a thorough interpretation of the uncertainty-aware optimization outcomes. Finally, since the proposed PHS uses the sea as the lower reservoir, additional technical challenges are addressed.

Plasmodium falciparum dihydroorotate dehydrogenase (PfDODH) is one of the enzymes currently explored in the treatment of malaria. Although there is currently no clinically approved drug targeting PfDODH, many of the compounds in clinical trials have [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine backbone structure. This study sought to design new compounds from the fragments of known experimental inhibitors of PfDODH. Nine experimental compounds retrieved from Drug Bank online were downloaded and broken into fragments using Schrodinger power shell; the fragments were recombined to generate new ligand structures using BREED algorithm. The new compounds were docked with PfDODH crystal structure, after which the compounds were filtered with extensive drug-likeness and toxicity parameters. A 2D-QSAR model was built using the multiple linear regression method and externally validated. The compounds electronic behaviours were studied using DFT calculations. Structural investigation of the six designed compounds, which had lower binding energies than the standard inhibitors, showed that five of them had [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine moieties and interacted with essential residues at the PfDODH binding site. In addition to their drug-like and pharmacokinetic properties, they also showed minimal toxicities. The externally validated 2D-QSAR model with R² and Q² values of 0.6852 and 0.6691, confirmed the inhibitory prowess of these compounds against PfDODH. The DFT calculations showed regions of the molecules prone to electrophilic and nucleophilic attack. The current study thus provides insight into the development of a new set of potent PfDODH inhibitors.

Statistical modeling lies at the heart of product design and development throughout numerous engineering disciplines, especially since processing large amounts of data has become increasingly ubiquitous. While mathematical statistics provide elegant guidance pertaining to the question of whether or not some particular underlying modeling assumptions are justified and appropriate, when pursuing a more comprehensive assessment of product design and development other considerations often increase in significance. Therefore, we will examine and analyze the tedious interactions and implications of statistical modeling choices and product liability exposure. To the best of our knowledge, this paper is the first to draw attention to and explore some often overlooked or oversimplified dangers and pitfalls that enter the equation when product design heavily relies on statistical modeling. In particular, through a diligent analysis of both statistical and legal aspects we will explore how statistically optimal procedures may yield far from optimal outcomes in terms of product liability when applied to actual real life problems and why suboptimal nonparametric or robust approaches may constitute better alternatives.

Background: The aim of the present investigation was to evaluate the clinical success of horizontal ridge augmentation in the severely atrophic maxilla (Cawood and Howell class IV) using freeze-dried custom made bone harvested from cadaver donors tibial hemiplateau and to analyze the marginal bone level gain prior dental implants placement at 9 months after bone grafting and before prosthetic rehabilitation. Methods: A 52-year-old woman received custom made bone grafts. Patient underwent CT scans 2 weeks prior and 9 months after surgery for graft volume and density analysis. Results: The clinical and radiographic bone observations showed a very low rate of resorption after bone graft and implant placement. Conclusions: The custom-made allograft material was a highly effective modality for restoring the alveolar horizontal ridge, resulting in this way to reduce the need to obtain autogenous bone from a secondary site with predictable procedure. Further studies are needed to investigate its behavior at longer time points.

The innovation driven Industry 5.0, in agreement with Industry 4.0, leads to consider human in a prominence position as the center of manufacturing field. This pushes towards the hybridization of manufacturing plants promoting a fully collaboration between human and robot. Furthermore, the new paradigm of "human centred design" and "anthropocentric design" allows enabling a synergistic combination of human and robot skills. However, properly collaborative workplaces are currently very few. Industry is still not confident, and systems integrators hesitate to venture into Human-Robot Collaboration (HRC). Despite the effort in collaborative robotics, a general solution to overcome the current limitations in designing of collaborative workplaces still misses. In the current work, a Knowledge-Based Approach (KBA) is adopted to face collaborative workplace designing problem. The framework resulting from the KBA allows developing a modelling paradigm that enable to define a streamlined approach for the layout designing of a collaborative workplace. Finally, a what-if analysis and a ANOVA analysis are performed to generate and evaluate a set of scenarios related to a collaborative workplace for quality inspection of welded parts. Facing the high complexity and multidisciplinary of HRC can be conveyed to develop a general design approach aimed at overcoming the difficulties that limit the spread of HRC in the manufacturing field.

The prefabricated ECC/RC combined shear wall structure is an innovative prefabricated composite structure with better seismic performance by using ECC materials with better ductility in the main force and energy consumption regions of the prefabricated reinforced concrete (RC) shear wall structure. The key factors controlling the seismic energy dissipation capacity of this kind of structure are the use regions of ECC in composite coupling beams, use regions of ECC in shear walls, strength of ECC, stirrup ratio of coupling beams, strength of longitudinal reinforcement and so on. The parameters affecting seismic energy consumption are quantified by the finite element analysis method. By comparing and analyzing the load-displacement curves, hysteresis curves, energy dissipation capacity and stiffness degradation of the prefabricated ECC/RC combined shear wall structure specimen under these parameters, it is proposed that the best use regions of ECC is the cast-in-situ zone of the coupling beams with the scope of no more than400 mm at the shear walls’ bottom. The strength grade, the strength grade of longitudinal reinforcement, and the stirrup ratio of coupling beams are suggested design as E40, HRB400 and 0.5%, respectively.

Advancements in Parametric Design, Generative Design, and automation in Building Information Modelling (BIM) have opened new opportunities for architects and engineers working on complex buildings, such as offices. These developments allow designers to enhance their designs, increase project efficiency, improve performance, and reduce project time and costs. To address conflicting objectives that arise during the design process, genetic algorithms with multi-objective optimization (MOO) have been employed in architectural design. The GENIUS project aims to optimize building shape, apertures, and shading systems in the concept and design stages, with a focus on energy and daylight performance. The project integrates BIM and visual programming tools with Artificial Intelligence techniques like Genetic Algorithms and RBFOpt model-based optimization. Optimization algorithms are used to identify the best solutions that meet all design objectives, helping architects optimize their designs and achieve desired outcomes. The workflow was tested on a case study of a large office building, with MOO focused on maximizing daylight performance using Spatial Daylight Autonomy metric and minimizing energy consumption using Energy Use Intensity metric. The project provides architects with a method to improve their designs using Algorithm Aided Design tools, which help identify the best solutions for complex design problems.

The pursuit of more efficient transport has led engineers to develop a wide variety of 1 aircraft configurations with the aim of reducing fuel consumption and emissions. However, these 2 innovative designs introduce significant aeroelastic couplings that can potentially lead to structural 3 failure. Consequently, aeroelastic analysis and optimization has become an integral part of modern 4 aircraft design. In addition, aeroelastic testing of scale models is a critical phase in aircraft devel- 5 opment, requiring accurate prediction of aeroelastic behaviour during scale model construction to 6 reduce costs and mitigate risks associated with full-scale flight testing. Achieving a high degree of 7 similarity between the stiffness, mass distribution and flow field characteristics of scaled models 8 and their full-scale counterparts is of paramount importance. However, achieving similarity is 9 not always straightforward due to the variety of configurations of modern lightweight aircraft, as 10 identical geometry cannot always be directly scaled down. This configuration diversity has a direct 11 impact on the aeroelastic response, necessitating the use of computational aeroelasticity tools and 12 optimization algorithms. This paper presents the development of an aeroelastic scaling framework 13 using multidisciplinary optimization. Specifically, a parametric Finite Element Model (FEM) of the 14 wing is created, incorporating parameterisation of both thickness and geometry, primarily using 15 shell elements. Aerodynamic loads are calculated using the Doublet Lattice Method (DLM) em- 16 ploying twist and camber correction factors, and aeroelastic coupling is established using infinite 17 plate splines. The aeroelastic model is then integrated within an Ant Colony optimization (ACO) 18 algorithm to achieve static and dynamic similarity between the scaled model and the reference wing. 19 A notable contribution of this work is the incorporation of internal geometry parameterisation into 20 the framework, increasing its versatility and effectiveness.

As the COVID-19 pandemic has caused enormous damage to society, economy and public health security, it is crucial to combat the epidemic and allocate social and health resources effectively. Global optimization algorithms are extensively used in many domains to find optimal solutions to complex problems. Thus, a survey of three typical global optimizations applied on the COVID-19 pandemic is timely. This article is structured into three typical global optimization algorithms - Genetic Algorithm, Particle Swarm Optimization, and Cat Swarm Optimization - and summarizes the framework models and practical applications, as well as other optimization methods that may be applied to COVID-19. Finally, current unresolved challenges and future research opportunities to be explored are summarized.

Calculating a minimum-time trajectory requires the solving of a boundary value problem resulting from invocation of necessary conditions of optimality to set up a set of ordinary differential equations to solve the trajectory between the initial position and desired ending position with set constraints on the path between the two. This manuscript expresses the minimum time optimum trajectory between a satellite in a geosynchronous orbit and a target set on earth’s surface utilizing a non-rotating earth centric coordinate system. Expressing motion in coordinates of rotating reference frames necessitates transformation between reference frames, and one such transformation is embodied in the Direction Cosine Matrices (DCM) formed by a sequence of three successive frame rotations. Rotation about the local wing of an aerospace vehicle is almost never the pitch angle, yet modern application of kinematics often assumes such (with accompanying angular error). The same assertion is usually true about the nature of roll and yaw angles. This manuscript evaluates which sequence is the most advantageous for an object starting in space and then travels through the atmosphere to a target on the Earth’s surface. Simulation precision (validated by the quaternion normalization condition) reveals the so-called 132 rotation is the most accurate with an average error of 0.14° and a computational time of 0.013 seconds: resulting in a 97.95% increase in accuracy over the ubiquitous 321 “aerospace” rotation sequence and a 99.84% increase over the so-called 313 “orbital” rotation sequence. Utilizing the proposed optimal trajectory candidate yields a total flight time of 2 hours, 34 minutes and 46 seconds, or an average velocity of 3.85 kilometers per second, while impacting the target with a velocity of 11.54 kilometers per second.

Multi-objective optimization (MOO) is an optimization involving minimization or maximization of several objective functions more than the conventional one objective optimization, which is useful in many fields. Many of the current methodologies addresses challenges and solutions that attempt to solve simultaneously several Objectives with multiple constraints subjoined to each. Often MOO are generally subjected to linear inequality, equality and or bounded constraint that prevent all objectives from being optimized at once. This paper reviews some recent articles in area of MOO and presents deep analysis of Random and Uniform Entry-Exit time of objectives. It further break down process into sub-process and then provide some new concepts for solving problems in MOO, which comes due to periodical objectives that do not stay for the entire duration of process lifetime, unlike permanent objectives which are optimized once for the entire process duration. A methodology based on partial optimization that optimizes each objective iteratively and weight convergence method that optimizes sub-group of objectives are given. Furthermore, another method is introduced which involve objective classification, ranking, estimation and prediction where objectives are classified based on their properties, and ranked using a given criteria and in addition estimated for an optimal weight point (pareto optimal point) if it certifies a coveted optimal weight point. Then finally predicted to find how far it deviates from the estimated optimal weight point. A Sample Mathematical Tri-Objectives and Real world Optimization was analyzed using partial method, ranking and classification method, the result showed that an objective can be added or removed without affecting previous or existing optimal solutions. Therefore suitable for handling time governed MOO. Although this paper presents concepts work only, it’s practical application are beyond the scope of this paper, however base on analysis and examples presented, the concept is worthy of igniting further research and application.

A Robust Optimization framework with original concepts and fundamentals also admitting a fusion of ideals from relative regret models and static robust optimization, containing conservatism concepts is disclosed. The algorithm uses a fine-tune strategy to tune the model so the robustness and a target ideality can be mutually achieved with a specified risk. The framework comprises original concepts, a mathematical approach and an algorithm. The statistical treatment of the data with the original concepts from the framework make it able to make short, middle or long-term decision-making setting. The framework has high tractability since the algorithm forces the creation of a setting that makes a robust optimization with the specified risk. The framework can be applied in linear and nonlinear mathematical models since that the objective function is monotonic in the domain of the active convex region. Several examples are solved to best understand the framework and all results demonstrated high tractability and performance. There is a wide range of applications. Along all the text, there is a profound discussion about its philosophy, objective, original concepts, fields of application, statistical and probabilistic fundamentals.

In this work, we propose a variation of the cellular particle swarm optimization algorithm with differential evolution hybridization (CPSO-DE), to include constrained optimization in it, named Ts-CPD. It is implemented as a kernel of electronic design automation (EDA) tool capable of sizing circuit components considering a single-objective design with restrictions and constraints. The aim is to improve the optimization solutions in the sizing of analog circuits. To evaluate our proposal’s performance, we present the design of three analog circuits: a deferential amplifier, a two-stage operational amplifier, and a folded cascode operational transconductance amplifier. Numerical simulation results indicate that Ts-CPD can find better solutions, in terms of the design objective and the accomplishment of constraints, than those reported in previous works.

Camera malfunctions or loss of storage elements in imaging devices may lead to loss of important image information or random impulse noise interference. Low rank is one of the important prior information in image optimization processing. This paper uses different low-rank constraint models of the image matrices to recover the impulse interference satellite images. Firstly, an overview of image inpainting models based on nuclear norm, truncated nuclear norm, weighted nuclear norm, and matrix-factorization-based F-norm is presented, and corresponding optimiza-tion iterative algorithms are provided. Then, we conducted experiments under three types of pulse interference and provided visual and numerical results. Finally, it is concluded that the WSVT_ADMM method based on the weighted nuclear norm can obtain the best image inpainting results; The UV_ADMM method based on F norm of matrix factorization has the least computa-tion time and can be used for large-scale low-rank matrix computation; The WSVT_ADMM method based on weighted nuclear norm and the TSVT_ ADMM method based on truncated nuclear norms can significantly improve the repair effect compared to the nuclear norm-based methods such as SVT, SVP, and n_ADMM.

Portfolio optimization is a mathematical formulation whose objective is to maximize returns while minimizing risks. A lot of improvement in the model has been made, including adding practical constraints. With the growing of shares trading, the problem becomes dimensionally very large. In this paper, we propose the usage of modified Biogeography-Based Optimization to solve the large scale constrained portfolio optimization. Results indicate the effectiveness of the method used.

Global optimization is an imperative development of local optimization because there are many problems in artificial intelligence and machine learning requires highly acute solutions over entire domain. There are many methods to resolve the global optimization, which can be classified into three groups such as analytic methods (purely mathematical methods), probabilistic methods, and heuristic methods. Especially, heuristic methods like particle swarm optimization and ant bee colony attract researchers because their effective and practical techniques which are easy to be implemented by computer programming languages. However, these heuristic methods are lacking in theoretical mathematical fundamental. Fortunately, minima distribution establishes a strict mathematical relationship between optimized target function and its global minima. In this research, I try to study minima distribution and apply it into explaining convergence and convergence speed of optimization algorithms. Especially, weak conditions of convergence and monotonicity within minima distribution are drawn so as to be appropriate to practical optimization methods.

Particle swarm optimization (PSO) is an effective algorithm to solve the optimization problem in case that derivative of target function is inexistent or difficult to be determined. Because PSO has many parameters and variants, I propose a general framework of PSO called GPSO which aggregates important parameters and generalizes important variants so that researchers can customize PSO easily. Moreover, two main properties of PSO are exploration and exploitation. The exploration property aims to avoid premature converging so as to reach global optimal solution whereas the exploitation property aims to motivate PSO to converge as fast as possible. These two aspects are equally important. Therefore, GPSO also aims to balance the exploration and the exploitation. It is expected that GPSO supports users to tune parameters for not only solving premature problem but also fast convergence.

Increasing demand for food production with limited available water resources pose the threat to agricultural activities. The conjunctive allocation of water resources maximizes the net benefit of farmers efficiently. In this study, a novel hybrid optimization model was developed based on a genetic algorithm (GA), bacterial foraging optimization (BFO) and ant colony optimization (ACO) to maximize the net benefit of water deficit Sathanur reservoir command. The GA-based opti-mization model considered crop-related physical and economical parameters to derive optimal cropping patterns for three different conjunctive use policies and further allocation of surface and groundwater for different crops are enhanced with the BFO. The allocation of surface and groundwater for the head, middle and tail reach obtained from BFO is considered as input to ACO as a guiding mechanism to attain an optimal cropping pattern. Comparing the average produc-tivity values Policy 3 (3.665 Rs/m3) has better values relating to Policy 1 (3.662 Rs/m3) and Policy 2 (3.440 Rs/m3). Thus, the developed novel hybrid optimization model (GA-BFO-ACO) is very promising to enhance the farmer's net income as well as for the command area water conservation and can be replicated in other irrigated regions of the globe to overcome chronic land and water problems.

This article introduces a novel nature-inspired metaheuristic algorithm called Frilled Lizard Optimization (FLO), which emulates the hunting behavior of frilled lizards in their natural habitat. FLO draws in-spiration from the sit-and-wait strategy observed in frilled lizards during hunting. The underlying theory of FLO is presented and mathematically formulated in two phases: (i) an exploration phase, simulating the frilled lizard's attack towards prey, and (ii) an exploitation phase, simulating the lizard's retreat to the top of the tree after feeding. To assess FLO's efficacy in solving optimization problems, the algorithm's performance is evaluated across fifty-two standard benchmark functions, encompassing unimodal, high-dimensional multimodal, fixed-dimensional multimodal, and the CEC 2017 test suite. Comparative analyses with twelve existing metaheuristic algorithms are conducted. The simulation results reveal that FLO, distinguished by its adeptness in exploration, exploitation, and balancing them during search process, outperforms competing algorithms. Additionally, FLO is implemented on twenty-two constrained optimization problems from the CEC 2011 test suite and four engineering design problems, demonstrating its effectiveness in addressing real-world optimization applications.

Recent research has enabled the integration of traditional Volt-VAr Control (VVC) resources, such as capacitors banks and transformer tap changers, with Distributed Energy Resources (DERs), such as photo-voltaic sources and energy storage, in order to achieve various Volt-VAr Optimization (VVO) targets, such as Conservation Voltage Reduction (CVR), minimizing VAr flow at the transformer, minimizing grid losses, minimizing asset operations and more. When more than one target function can be optimized, the question of multi-objective optimization is raised. In this work, we propose a general formulation of the multi-objective Volt-VAr optimization problem. We consider the applicability of various multi-optimization techniques and discuss the operational interpretation of these solutions. We demonstrate the methods using simulation on a test feeder.

Modern power system integrates more and more new energy and use a large number of power electronic equipment. This makes it face more challenges in online optimization and real-time control. Deep reinforcement learning(DRL) has the ability of processing big data and high-dimensional features, as well as the ability of independently learning and optimizing decision-making in complex environments. In this paper, we explore DRL based online combination optimization method of grid section for large complex power system. In our method, to improve the convergence speed of the model, we propose to discretize the output action of the unit and simplify the action space. We also design a reinforcement learning loss function with strong constraints to further improve the convergence speed of the model and facilitate the algorithm to obtain the stable solution. Moreover, to avoid the local optimal solution problem caused by the discretization of the output action, we propose to use the annealing optimization algorithm to make the granularity of the unit output finer. We verify our method on IEEE 118-bus system. The experimental results show that our model has fast convergence speed and better performance, and can obtain stable solutions.

We consider the problem of scheduling tasks on a single machine subject to an uncertain breakdown to minimize the flowtime. Assume the machine is unavailable during the breakdown; the starting time of the breakdown is a random variable s with distribution function D(s) and the terminating time of the breakdown has no any other information; jobs are non-resumable. Under the assumptions, starting from the perspective of statistical optimization, we first define the expected competitive ratio of an algorithm to find the optimized solution with the considered problem. Further, we propose and prove a certain result on the expected competitive ratio of the SPT rule. In particular, we show that under a quite loose condition the expected competitive ratio of the SPT rule is no more than 5/4. Meanwhile, we also make some discussions about our studies. What we have done will rich and improve the studying results on the area of scheduling to minimize flowtime and advance the development of online optimization and statistical optimization.

Malicious apps specifically aimed at the Android platform have increased in tandem with the proliferation of mobile devices. Malware is now so carefully written that it is difficult to detect. Due to the exponential growth in malware, manual methods of malware are increasingly ineffec-tive. Although prior writers have proposed numerous high-quality approaches, static and dy-namic assessments inherently necessitate intricate procedures. The obfuscation methods used by modern malware are incredibly complex and clever. As a result, it cannot be detected using only static malware analysis. As a result, this work presents a hybrid analysis approach, partially tai-lored for multiple-feature data, for identifying Android malware and classifying malware families to improve Android malware detection and classification. This paper offers a hybrid method that combines static and dynamic malware analysis to give a full view of the threat. Three distinct phases make up the framework proposed in this research. Normalization and feature extraction procedures are used in the first phase of pre-processing. Both static and dynamic features undergo feature selection in the second phase. Two feature selection strategies are proposed to choose the best subset of features to use for both static and dynamic features. The third phase involves ap-plying a newly proposed detection model to classify android apps; this model uses a neural net-work optimized with an improved version of HHO. Application of binary and multi-class classi-fication is used, with binary classification for benign and malware apps and multi-class classifica-tion for detecting malware categories and families. By utilizing the features gleaned from static and dynamic malware analysis, several machine-learning methods are used for malware classifi-cation. According to the results of the experiments, the hybrid approach improves the accuracy of detection and classification of Android malware compared to the scenario when considering static and dynamic information separately.

Photovoltaic systems and wind energy systems are generally used in distributed system. However, zero-sequence and harmonic currents occur due to photovoltaic systems, and positive-sequence harmonic currents occur due to wind turbines. Thus, the sheath current in high voltage cables increases due to these currents and poor power quality in distributed generation plants. Metal parts of the cable are grounded to prevent the negative effects of sheath currents. When long high voltage cable lines are grounded with the method in the literature, high sheath current and voltage occur on the cable sheath. Therefore, the SSBLR method is designed as a new method for the distributed generation system. The SSBLR method has been optimized with prediction methods and multi-objective optimization methods to prevent negative effects of the sheath current. Pareto optimal method is used as multi-objective optimization method, and artificial neural network, hybrid artificial neural network and regression methods are used as prediction method. The most dominant result is searched using different estimation and optimization methods in pareto optimal method. When the artificial neural network-genetic algorithm hybrid method is used as a prediction method, and genetic algorithm used as optimization method, significant decreases are observed in sheath current and voltage.

The current study aims to develop a methodology for obtaining topology-optimal structures made of short fiber-reinforced polymers, which include the fluid-structure interaction. Accounting for the molding process during the internal iterations of topology optimization makes it possible to enhance the weight efficiency of structures—a crucial aspect, especially in aerospace. Anisotropy is considered through the fiber orientation tensor, which is modeled by solving the plastic molding equations for non-Newtonian fluids, and then introduced as a variable of the stiffness matrix during the structural analysis. The materials used were non-linearly modeled using an exponential-and-linear hardening law. The evaluation of weight efficiency in structures composed of short-reinforced composite materials using a dimensionless criterion is addressed. Experimental verification was performed to confirm the validity of the developed methodology. The evidence illustrates that considering anisotropy leads to stiffer structures and structural elements should be oriented in the direction of maximal stiffness. The load-carrying factor can be expressed in terms of failure criteria. The presented multidisciplinary methodology can be used to improve the quality of the design of structures made of short fiber-reinforced composites (SFRC) where high stiffness, high strength, and minimum mass are the primary required structural characteristics.

The main goal of this paper is to show that Bayesian optimization could be regarded as a general framework for the data driven modelling and solution of problems arising in water distribution systems. Hydraulic simulation, both scenario based, and Monte Carlo is a key tool in modelling in water distribution systems. The related optimization problems fall in a simulation/optimization framework in which objectives and constraints are often black-box. Bayesian Optimization (BO) is characterized by a surrogate model, usually a Gaussian process, but also a random forest and increasingly neural networks and an acquisition function which drives the search for new evaluation points. These modelling options make BO nonparametric, robust, flexible and sample efficient particularly suitable for simulation/optimization problems. A defining characteristic of BO is its versatility and flexibility, given for instance by different probabilistic models, in particular different kernels, different acquisition functions. These characteristics of the Bayesian optimization approach are exemplified by the two problems: cost/energy optimization in pump scheduling and optimal sensor placement for early detection on contaminant intrusion. Different surrogate models have been used both in explicit and implicit control schemes. Showing that BO can drive the process of learning control rules directly from operational data. BO can also be extended to multi-objective optimization. Two algorithms have been proposed for multi-objective detection problem using two different acquisition functions.

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

The research paper presents a new approach towards constructing motion equations for structures with attached MTMDs (multiple tuned mass dampers). A primary system, with MDOF (multiple dynamic degrees of freedom) was reduced to an equivalent system with a SDOF (single degree of freedom) through the modal approach, and equations from additional MTMDs were added to a thus-created system. Optimization based on H2 and H∞ for the transfer function associated with the generalized displacement of an SDOF system. The research work utilized GA (genetic algorithms) and SA (simulated annealing method) optimization algorithms to determine the stiffness and damping parameters for individual TMDs. The effect of damping and stiffness (MTMD tuning) distribution depending on the number of TMDs was also analyzed. The paper also reviews the impact of primary system mass change on the efficiency of optimized MTMDs, as well as confirms the results of other authors involving greater MTMD effectiveness relative to a single TMD.

We developed a novel hybrid approach for solving global optimization, computer science, bio-medical and engineering real life applications that is based on the coupling of the Whale Optimizer and Sine Cosine Algorithms via a surrogate model. We relate the whale optimizer algorithm to balance between the exploitation and the exploration process in the proposed method. There exist confirmed techniques for searching approximate best optimal solutions, but our algorithm will further guarantee that such numerical and statistical solutions satisfy physical bounds of the standard and real life functions. Our experiments with the benchmark, bio-medical, computer science and engineering real life problems have illustrated the advantages of using a newly hybrid approach based on mixing Whale Optimizer and Sine Cosine algorithms. It holds considerable potential for reducing execution time for solving standard and real life problems and at the same time improving the quality of the solution.

With the every passing day, the demand for data traffic is increasing and this demand forces the research community not only to look for alternating spectrum for communication but also urges the radio frequency planners to use the existing spectrum smartly. Cell size is shrinking with the every upcoming communication generation which makes the base station placement planning complex and cumbersome. In order to make the next-generation cost-effective, it is important to design the network in such a way which utilizes minimum number of base stations while ensure coverage and quality of service. This paper aims at develop a new approach using hybrid metaheuristic and metamodel applied in multi-transmitter placement planning (MTPP) problem. We apply radial basis function (RBF) metamodel to assist particle swarm optimizer (PSO) in a constrained simulation-optimization (SO) of MTPP to mitigate the associated computational burden of optimization procedure. We evaluate the effectiveness and applicability of proposed algorithm in a case study by simulating MTPP model with two, three, four and five transmitters.

Baggage overweight is a significant phenomenon in the air travel in- dustry which is both regulated by the governments and highly profitable for the airlines. The recent years increase in airlines' profits is attributed to so-called ancillary payments – all consumer costs excluding the actual transportation fare. Baggage overweight fees, being a part of such pay- ments, have high profit-generation potential. Is the pricing for baggage overweight positioned correctly? The rationality of policies currently used by airlines is questionable, as they lack a customer-oriented marketing ap- proach. The general purpose of this research is to explore the possibilities of rational baggage overweight pricing for airlines by developing a multi- level price optimization model aimed to maximize company revenue. The modeling is based on determining consumer Willingness-To- Pay values for baggage overweight, and providing an optimal ticket price for them to maximize company expected revenue. The total profit value is forecasted too, based on the company market share and revenue level.

One control challenge in prosthetic legs is seamless transition from one gait mode to another. User intent recognition (UIR) is a high-level controller that tells a low-level controller to switch to the identified activity mode, depending on the user’s intent and environment. We propose a new framework to design an optimal UIR system with simultaneous maximum performance and parsimony for gait mode recognition. We use multi-objective optimization (MOO) to find an optimal feature subset that creates a trade-off between these two conflicting objectives. The main contribution of this paper is two-fold: (1) a new gradient-based multi-objective feature selection (GMOFS) method for optimal UIR design; and (2) the application of advanced evolutionary MOO methods for UIR. GMOFS is an embedded method that simultaneously performs feature selection and classification by incorporating an elastic net in multilayer perceptron neural network training. Experimental data are collected from six subjects, including three able-bodied subjects and three transfemoral amputees. We implement GMOFS and four variants of multi-objective biogeography-based optimization (MOBBO) for optimal feature subset selection, and we compare their performances using normalized hypervolume and relative coverage. GMOFS demonstrates competitive performance compared to the four MOBBO methods. We achieve a mean classification accuracy of 97.14% ± 1.51% and 98.45% ± 1.22% with the optimal selected subset for able-bodied and amputee subjects, respectively, while using only 23% of the available features. Results thus indicate the potential of advanced optimization methods to simultaneously achieve accurate, reliable, and compact UIR for locomotion mode detection of lower-limb amputees with prostheses.

In this paper, the entire downhole fluid sucker rod pump system is replaced with a viscoelastic vibration model, namely a third-order differential equation with an inhomogeneous forcing term. Both Kelvin and Maxwell viscoelastic models can be implemented along with the dynamic behaviors of a mass point attached to the viscoelastic model. By employing the time-dependent polished rod force measured with a dynamometer as the input to the viscoelastic dynamic model, we have obtained the displacement responses, which match closely with the experimental measurements in actual operations, through an iterative process. The key discovery of this work is the feasibility of the so-called inverse optimization procedure which can be utilized to identify the equivalent scaling factor and viscoelastic system parameters. The proposed Newton-Raphson iterative method with some terms in the Jacobian matrix expressed with averaged rates of changes based on perturbations of up to two independent parameters provides a feasible tool for optimization issues related to complex engineering problems with mere information of input and output data from either experiments or comprehensive simulations. The same inverse optimization procedure is also implemented to model the entire fluid delivery system of a very viscous non-Newtonian polymer modeled as a first-order ordinary differential system similar to the transient entrance developing flow. The convergent parameter reproduces transient solutions which match very well with those from full-fledged computational fluid dynamics models with the required inlet volume flow rate and the outlet pressure conditions.