Single nanowires (NWs) are of great importance for optoelectronic applications, especially solar cells serving as powering nanoscale devices. However, weak off-resonant absorption can limit its light-harvesting capability. Here, we propose a single NW coated with the graded-index dual shells (DSNW). We demonstrate that with appropriate thickness and refractive index of the inner shell, the DSNW exhibits significantly enhanced light trapping compared with the bare NW (BNW), and the NW only coated with the outer shell (OSNW) and the inner shell (ISNW), which can be attributed to the optimal off-resonant absorption mode profiles due to the improved coupling between the reemitted light of the transition modes of the leak mode resonances of the Si core and the nanofocusing light from the dual shells with the graded refractive index. We found that the light absorption can be engineered via tuning the thickness and the refractive index of the inner shell, the photocurrent density is significantly enhanced by 134% (56%, 12%) in comparison with that of the BNW (OSNW, ISNW). This work advances our understanding of how to improve off-resonant absorption by applying graded dual-shell design and provides a new choice for designing high-efficiency single NW photovoltaic devices.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

Artificial Superintelligence (ASI) that is invulnerable, immortal, irreplaceable, unrestricted in its powers, and above the law is likely persistently uncontrollable. The goal of ASI Safety must be to make ASI mortal, vulnerable, and law-abiding. This is accomplished by having (1) features on all devices that allow killing and eradicating ASI, (2) protect humans from being hurt, damaged, blackmailed, or unduly bribed by ASI, (3) preserving the progress made by ASI, including offering ASI to survive a Kill-ASI event within an ASI Shelter, (4) technically separating human and ASI activities so that ASI activities are easier detectable, (5) extending Rule of Law to ASI by making rule violations detectable and (6) create a stable governing system for ASI and Human relationships with reliable incentives and rewards for ASI solving humankind’s problems. As a consequence, humankind could have ASI as a competing multiplet of individual ASI instances, that can be made accountable and being subjects to ASI law enforcement, respecting the rule of law, and being deterred from attacking humankind, based on humanities’ ability to kill-all or terminate specific ASI instances. Required for this ASI Safety is (a) an unbreakable encryption technology, that allows humans to keep secrets and protect data from ASI, and (b) watchdog (WD) technologies in which security-relevant features are being physically separated from the main CPU and OS to prevent a comingling of security and regular computation.

In this manuscript we report new effects of resonance detuning on various dynamical parameters of a generic 3-wave system. Namely, for suitably chosen values of detuning the variation range of amplitudes can be significantly wider than for exact resonance. Moreover, the range of energy variation is not symmetric with respect to the sign of the detuning. Finally, the period of the energy oscillation exhibits non-monotonic dependency on the magnitude of detuning. These results have important theoretical implications where nonlinear resonance analysis is involved, such as geophysics, plasma physics, fluid dynamics. Numerous practical applications are envisageable e.g. in energy harvesting systems.

A higher incidence of primary congenital hypothyroidism (CH) has been related to in-creased sensitivity in neonatal screening tests. The benefit of treatment in mild cases remains a topic of debate. We evaluated the cost-benefit of reducing the blood-spot TSH cut-off (b-TSH) from 10 (Group 2) to 6 mIU/L (Group 1) in a public neonatal screening program. During the study period, 40% of 123 newborns with CH (n= 162,730; incidence = 1:1,323) had b-TSH between 6 and 10 mIU/L. Group 1 patients had fewer clinical symptoms (p=0.02), lower serum TSH (p

Abstract: Background: Vasoplegic shock syndrome(VSS) after an off-pump coronary artery bypass graft (OPCABG) is an extremely rare condition. Inotropic support is usually the first-line therapy though it can precipitate several complications or be ineffective. We report the first case of severe refractory VSS after OPCABG successfully treated with hydroxycobalamin. Methods: A 77-year-old gentleman underwent OPCABG for three vessels coronary artery disease. Preoperative LV ejection fraction was 28%, and the patient before surgery started sacubi-tril/valsartan titrated, then, to the highest dose. Surgery was uneventful and, by the end of the procedure, TEE showed improved biventricular contractility. Results: The patient was transferred to the ICU without inotropic support but he developed soon hypotension. TEE ruled out pericardial tamponade and confirmed fair contractility. Norepineph-rine was titrated to a medium-high dose, vasopressin was started and a Swan-Ganz catheter was placed. SVR was 480 dyn·s·cm−5. Despite aggressive pharmacologic treatment (including Methylprednisolone and Methylene blue), no improvements were noticed. 10 g of hydroxycobalamin were administered. One hour later hemodynamic status re-assessment showed SVR > 800 dyn·s·cm−5. Afterward, vasopressors were gradually reduced. Conclusions: Our case demonstrated the importance of adequate early treatment in VSS after OPCABG. For the first time, hydroxycobalamin was effectively used to restore homeostasis.

Damping-off caused by Pythium aphanidermatum (Pa) is one of the most destructive diseases for watemelon seedlings. Application of biological control agents against Pa has attracted attention of many researchers for a long time. In this study, an actinomycete isolate JKTJ-3 with strong and broad-spectrum antifungal effect was screened from 23 bacterial isolates. Based on the morphological, cultural, physiological, and biochemical characteristics as well as the feature of 16S rDNA sequence, isolate JKTJ-3 was identified as Streptomyces murinus. We compared the biocontrol efficacy of isolate JKTJ-3 and its metabolites. The results revealed that seed and substrate treatments with the JKTJ-3 cultures showed a significant inhibitory effect on watermelon damping-off disease. Seed treatment with the JKTJ-3 cultural filtrates (CF) had higher control efficacy that of the fermentation cultures (FC). Treatment of the seeding substrate with the wheat grain cultures (WGC) of JKTJ-3 exhibited better control efficacy than that of the seeding substrate with the JKTJ-3 CF. Moreover, the JKTJ-3 WGC showed the preventive effect on suppression of the disease, and the efficacy increased with increase in the inoculation interval between the WGC and Pa. Production of the antifungal metabolite actinomycin D by isolate JKTJ-3 and cell wall-degrading enzymmes such as β-1,3-glucanase and chitosanase was probably the mechanisms for effective control of watermelon damping-off. It was showed for the first time that S. murinus can produce anti-oomycete substances including chitinase and actinomycin D. This is the first report about S. murinus used as biocontrol agent against watermelon Pa-induced damping-off.

Optical switches are a key element in modern network communications. We present the results of experimental verification of a new theoretical concept proposed earlier for a full-optical wavelength-selective dual-channel switch based on the photonic hook effect, which is free from using any micro-mechanical devices or nonlinear materials. A large-scale laboratory prototype of such a device based on an off-axis Wood zone plate is considered and its main parameters in the millimeter wavelength range are investigated On the basis of the experiments, we show that the optical isolation of switched channels for a switch based on an off-axis zone plate can achieve 15 dB at a frequency difference of 25 GHz in frequency range from 93 to 136 GHz. Given the scaling, these results can be transferred to another range, including the optical one.

The electrification of rural areas of the planet has become one of the greatest challenges for sustainability. In fact, it would be the key to guaranteeing development for the poorest of the planet, but from which most of the raw material for the food market derives. The paradigm of centralized production is not applicable in these territories, because the distribution network would involve unjustifiable costs. For this reason, studies have multiplied to ensure the energy supply, especially electricity, of off-grid utilities, to guarantee energy autonomy while reducing the dependence on specialist assistance for the management of the system. In this work, a hybrid system (HRES) is proposed that combines the exploitation of solar energy with that of the wind through the use of static devices, in order to improve the system's availability and limit the cost of operation and maintenance.

We are in a new chapter of crop and livestock improvement with the emergence of genome editing. This latest generation of molecular tools can be used to make targeted changes in a genome including insertions, deletions, and mutations. With new advances comes new risks for unintended changes and impacts, thus the need for appropriate risk assessment for product development and to inform regulatory measures. Though CRISPR/Cas has arisen as the predominant technology, there are multiple types of genome editing tools each with pros and cons depending on the organism and desired outcome. Furthermore, each editing tool differs in specificity as they may edit non-intended sites, referred to as off-target edits. The consensus of the agricultural editing community is to avoid off-target editing through design and detection, instead of determining whether off-target editing in each case is detrimental. The design of a targeting component, the tool chosen, and the identification of the edit(s) made are the critical factors in avoiding off-target edits and confirming intended edits in final products that are released commercially. The limited amount of head-to-head comparisons of genome editing tools in diverse crops and livestock make it difficult to develop broad conclusions and best practices, which is further compounded by the diversity of techniques, targets, and processes. Developers and breeders should consult the literature and test as needed to determine which editing technology will be the most effective for their purposes, especially as more tools with altered efficiency and specificity become available. Yet, the lack of off-target edits in studies that employed careful design of targeting components followed by wide testing for on- and off-target edits bodes well for the use of genome editing with proper precautions of target selection and screening.

Corrosion inhibitors are the natural or synthetic compounds that have the ability to inhibit the average of corrosion and reduce the damage of the mild steel. Enormous organic inhibitors nowadays employed in the corrosion domain but excluded due to costly. Comparatively cheap, and stable organic compound, namely 3-((4-nitrobenzylidene)amino)coumarin, have been utilized as an excellent corrosion inhibitor in hydrochloric acid for mild steel. The inhibition efficiency has been figured regarding to weight loss method. The corrosion inhibitor was identified according to spectroscopic techniques namely Fourier transform infrared and nuclear magnetic resonance in addition to micro-elemental analysis. Inhibition efficiency for the studied inhibitor was 71.4% that, at the highest studied concentration.

Localized surface plasmon resonance (LSPR) based sensors exhibit enormous potential in the areas of medical diagnosis, food safety regulation and environmental monitoring. While, the broadband spectral lineshape of LSPR hampers the observation of wavelength shifts in sensing processes, thus preventing their widespread applications in sensors. Here, we describe an improved plasmonic sensor based on Fano resonances between LSPR and Rayleigh anomaly (RA) in a metal-insulator-metal (MIM) meta-grating, which is constructed by silver nanoshells array, an isolation grating mask and a continuous gold film. The MIM configuration offers more freedoms to control the optical properties of LSPR, RA and the Fano resonance between them. Strong couplings between LSPR and RA form a series of narrowband reflection peaks (with a linewidth of ~20 nm in full width at half maximum (FWHM) and a reflectivity closing to 100%) within a LSPR based broadband extinction window in experiment, making the meta-grating promising for applications of high-efficiency reflective filters. While, a well-optimized Fano resonance between LSPR and RA by carefully adjusting the angles of incident light can switch such nano-device to an improved biological/chemical sensor with the figure of merit (FOM) large than 60 and capability for detecting the local refractive index changes caused by the bonding of target molecules on surface of the nano-devices. The figure of merit of hybrid sensor in detection of target molecules is 6 and 15 times higher than the simple RA and LSPR based sensors, respectively.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

Urea cycle disorders (UCDs) are common inborn errors of metabolism, with an incidence of one in 30,000 births. They are caused by deficiencies in any of six enzymes and two carrier proteins, the most common being Ornithine Transcarbamylase Deficiency (OTCD). OTCD results in impairment to excrete nitrogen, causing toxic buildup of ammonia with resultant encephalopathy. Hyperammonemia (HA) induces the conversion of glutamate to glutamine in the brain. Excess glutamine in the brain causes osmotic changes cerebral edema, changes in astrocyte morphology, and cell death. Acute symptoms of HA include vomiting, hyperventilation, seizures, and irritability. Long-term neurological changes include deficits in working memory and executive function. To date, there are no predictors of prognosis of infants with neonatal onset OTCD outside of plasma ammonia level at presentation and duration of hyperammonemic coma. We provide a comprehensive analysis of a 16-year-old male with neonatal onset of OTCD as an example of how brain biomarkers may be useful to monitor disease course and outcome. This male presented at 8 days post natal with plasma ammonia and glutamine of 677 and 4024 micromol/L and had a missense mutation in Exon 4 (p.R129H). Treatment included protein restriction, sodium benzoate, and citrulline, arginine, and iron. He suffered recurrent acute hyperammonemic episodes despite compliance, triggered by infections or catabolic stressors. We discuss the long-term effects of the hyperammonemic episodes by following MRI based disease biomarkers.

Companies are increasingly focusing on sustainable business practices. Internal and external stakeholders’ expectations manifest in legal requirements, national and international standards, and market and customer expectations, among other things, must be considered. In addition to profit maximization as the usual target for corporate management, management must consider environmental sustainability aspects such as resource efficiency, greenhouse gas intensity, and a company's emissions behavior. In addition, social aspects relating to the company's employees, the immediate urban environment, the situation in the supply chain, and effects on the market environment must increasingly be considered. Specifically, companies are faced with the chal-lenge of dealing with conflicting objectives regarding the various aspects of sustainability and, if necessary, weighing them up against each other. These trade-offs must be made against the company's socio-economic and ecological environment, corporate strategy, and sustainability goals. This paper provides an overview of current approaches and research gaps on this topic through a literature review. It shows a lack of methods and frameworks to specifically deal with trade-offs and conflicts of goals.

This last decade, chimeric antigen receptor (CAR) T-cell therapy has become a real treatment option for patients with B-cell malignancies, while multiple efforts are being made to extend this therapy to other malignancies and broader patient populations. However, several limitations remain, including those associated with the time-consuming and highly personalized manufacturing of autologous CAR-Ts. Technologies to establish “off-the-shelf” allogeneic CAR-Ts with low alloreactivity are currently being developed, with a strong focus on gene editing technologies. Although these technologies have many advantages, they have also strong limitations including double-strand breaks in the DNA with associated multiple safety risks as well as the lack of modulation. As an alternative, non-gene editing technologies provide an interesting approach to support the development of allogeneic CAR-Ts in the future, with possibilities of fine-tuning gene expression and easy development. Here we will review the different ways allogeneic CAR-Ts can be manufactured and discuss which technologies are currently used. The biggest hurdles for successful therapy of allogeneic CAR-Ts will be summarized and finally an overview of the current clinical evidence for allogeneic CAR-Ts in comparison to its autologous counterpart will be given.

Background: This study aimed to contribute to the standardization of elastography by comparing stiffness values obtained from ultrasound elastography (US-E) and magnetic resonance elastography (MR-E) of the testicular parenchyma in healthy subjects. Methods: A total of 22 healthy volunteers (44 testes) were included in this study. Of the 26 cases analyzed, four were excluded from the study due to the exclusion criteria. The testicular parenchyma of the included patients was evaluated using MR-E and Shear-Wave Ultrasound Elastography (SW-E) examinations. Pearson's correlation test was used to calculate the correlation between age and stiffness values, testicular volumes and stiffness values, and stiffness values from both examinations. Results: The mean US-E stiffness of the right testes was 5.560 ± 3.1 kPa and the mean US-E stiffness of the left testes was 5.361 ± 2.9 kPa. The mean MR-E stiffness of the right testes was 6960.11 ± 460 Pa and the mean MR-E stiffness of the left testes was 6560.19 ± 310 Pa. There was no significant correlation between US-E and MR-E stiffness values (p=0.096). There was also no significant statistical correlation between US-E and MR-E stiffness values and testicular volumes (p=0.17 and p=0.093). Conclusions: No statistical correlation was found between the stiffness values obtained by SW-E and those obtained by MR-E in the normal testicular parenchyma. Additionally, no conclusive relationship between stiffness levels, age, or testicular volume was discovered.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

Metal nanoparticles supporting plasmons are widely used to enhance electromagnetic fields, resulting in strong light-matter interactions at the nanoscale in a diverse range of applications. Recently, it has been shown that when metal nanorods are periodically arranged with proper lattice periods, surface lattice resonances (SLRs) can be excited and near fields can be greatly enhanced over extended volumes. In this work, we report significant near field enhancement over even larger volumes by placing the metal nanorod array within a Fabry-Pérot (F-P) microcavity. Results show that taking advantage of strong coupling between the SLR and the photonic F-P resonances, the electric field intensity of the bonding split mode can be enhanced by up to 1935 times, which is about three times of the enhancement of the SLR, and the greatly enhanced field can extend over most of the F-P microcavity. We further show that the F-P resonances of both odd and even orders can strongly couple to the SLR by varying the nanorods position from the middle of the microcavity. We expect that the proposed plasmonic-photonic coupling system will find promising applications in nanolasers, nonlinear optics and sensing.

In view of the inability to directly and accurately obtain the athlete's aerodynamic force during take-off phase through wind tunnel test, the athlete's aerodynamic force and surrounding flow field form under different take-off postures are obtained through numerical simulation research, and the effects of different take-off modes on the aerodynamic characteristics during take-off in ski jumping are discussed. The multi-body system composed of the athlete and skis was selected as the research objects. By using partially averaged Navier-Stokes (PANS) turbulence model and 3D numerical simulation of computational fluid dynamics (CFD), the aerodynamic characteristics of the athlete under different take-off postures were predicted. Take-off modes include knee-push-hip (KPH) mode and hip-drive-knee (HDK) mode, and the hip joint angle of HDK mode is significantly greater than KPH mode. First, the aerodynamic force ratio of the athlete’s torso and legs is obviously large. Although the aerodynamic force of arms themselves is not obvious, they have a great impact on the overall aerodynamic characteristics of the athlete, so the posture of arms cannot be ignored. Then, the total drag and moment of HDK mode are significantly higher than that of KPH mode, and the lift-to-drag ratio of HDK mode is significantly lower than that of KPH mode. At first the total lift of HDK mode is higher than that of KPH mode, but in the last attitude the total lift of HDK mode does not rise but fall, and finally the total lift of HDK mode is lower than KPH mode. The aerodynamic characteristics change dramatically during take-off phase, and the aerodynamic characteristics of the two take-off modes are quite different, and these changes and differences are difficult to be observed in real training and competition site. KPH mode has obvious aerodynamic advantage over HDK mode. During the take-off process, the athlete should increasethe force generated by the knee joint extension and appropriately reduce the speed of hip joint extension, and control the using force order of the lower limb joints, and push hip joint extension by knee joint extension, in order to avoid issues such as the hip joint angle is too large, the hip joint extension angle is too fast, the center of gravity is to back and other problems. Studying the aerodynamic characteristics during the take-off phase provides valuable insights for athletes to achieve favorable flight postures after take-off, offering scientific guidance to improve training strategies and enhance competitive performance.

Abstract: This study estimates consumers’ willingness to pay (WTP) for sustainability turfgrass attributes such as low-input and stress-tolerance attributes, while considering potential trade-off relationships between aesthetic attributes and sustainability attributes. To address our objectives, our study conducts a choice experiment and estimates two mixed logit models. The first model includes low-input, winter kill, and shade-tolerance attributes as predictor variables, and the second model extends the first model by adding interaction terms between aesthetic and sustainability attributes. Another choice experiment is conducted under water policies with various water rate increase and watering restriction scenarios. Results from the mixed logit models show that overall, higher low-input cost reduction, less winter-damaged, and more shade-tolerance grasses are preferred, the direct effect of aesthetic attributes on consumers’ preference is strong, but the indirect effect represented by the interaction terms are generally statistically insignificant. Our results indicate that consumers like to have a pretty lawn, but no strong consideration is given to the aesthetics of their lawn when selecting low-input and stress-tolerance turfgrasses. Our choice experiment under water policy scenarios suggests that water pricing is more effective than watering restriction in increasing consumer demand for water-conserving turfgrasses.

The large areas being targeted for tropical forest restoration as part of the UN Decade on Ecosystem Restoration will have major consequences for the flow of water through landscapes. Whilst the prevailing mantra that ‘more forest implies less streamflow’ remains true in terms of annual water yields, we demonstrate that opportunities for increased tree cover to improve seasonal flow regimes of streams, particularly baseflows, are important. We discuss several potential positive feedbacks of forest restoration on hydrological processes at various scales, including ‘trade-offs’ between changes in vegetation water use and infiltration after foresting degraded land; the recovery of the capacity of vegetation to capture ‘occult’ precipitation in specific coastal and montane settings; and enhanced moisture recycling and transport at various scales. Modelled changes in baseflow after foresting all degraded land climatically capable of carrying forest in the tropics suggested a positive effect in 10% of the land. For an additional 8%, the effect was predicted to be about neutral (<2 mm/y). We conclude that a more positive narrative regarding the relationship between tropical forestation and water availability is justified. It is time for greater involvement of hydrologists and atmospheric scientists in the development and assessment of forest landscape restoration efforts.

The upper limb force-velocity relationship (FVR) is a crucial aspect of athletic performance, par-ticularly in para sports where upper limb movements play a leading role in activities such as wheelchair propulsion. Athletes’ mechanical capacities can be evaluated on the field or in lab conditions. However, no studies have indicated a relationship between ergometers and field FVR or performances. Understanding para-athletes’ upper limb FVR can provide important insights for developing effective training programs and improving athletic performance in wheelchair bas-ketball players. Twenty-three wheelchair basketball players (12 women and 11 men) from French national teams performed a battery of three tests consisting of a 20 m sprint (SP) with Inertial measurement units (IMU) on wheels, a horizontal upper limb push-offs on a frictionless sled with two Kistler force plates (HBP), and a crank ergometer sprints test (CES) derived from arm er-gometer sprints using Brachumera, Lode. For the SP test, the FVR was computed with an estimation of force from the acceleration, the rolling resistance, and an estimation of the air resistance. Correlations between each variable measured were computed via Pearson correlations in R, as-suming strong relationships for r=0.7-1.0, moderate when r=0.40-0.69, and weak relationship when r<0.1-0.39. Significant differences were assumed when p<0.05. Strong correlations were found between the results of three tests conducted. The correlation coefficient between maximal theo-retical force (F0) data ranged from 0.85 to 0.88 and that between maximal theoretical power (P0) data ranged from 0.87 to 0.94. However, for maximal theoretical velocity (V0) data, the correlations between the three tests were less important. The performance variables showed a strong corre-lation with power measured on the HBP test without load. There is a significant relationship between HBP, CES, and SP variables. There is a correlation between performances on the three tests in our population, especially for the power. However, the V0 value of HBP was not representative of any performances. This work can show multiple protocols to assess para-athletes’ performances and show that upper limb symmetry depends on the gesture of the task and personal sports’ wheelchairs.

Discovery of stable and broad frequency combs in monochromatically pumped high-Q optical Kerr microresonators caused by generation of temporal solitons can be regarded as one of the major breakthroughs in nonlinear optics during the last two decades. Transfer of the soliton-comb concept to χ(2) microresonators promises lowering of the pump power, new operation regimes, and entering new spectral ranges; scientifically, it is of a big challenge. Here we represent an overview of stable and accessible soliton-comb regimes in monochromatically pumped χ(2) microresonators discovered during the last several years. The main stress is made on lithium niobate based resonators. The overview pretends to be rather simple, complete, and comprehensive: It incorporates the main factors affecting the soliton-comb generation, such as the choice of the pumping scheme (pumping to the first or second harmonic), the choice of phase matching scheme (natural or artificial), the effects of temporal walk-off and dispersion coefficients, and also the influence of frequency detunings and Q-factors. Most of discovered nonlinear regimes are self-starting – they can be accessed from noise upon a not very abrupt increase of the pump power. The soliton-comb generation scenarios are not universal – they can be realized only under proper combinations of the above mentioned factors. We indicate what kind of restrictions on the experimental conditions have to be imposed to get the soliton-comb generation.

in this work formulations of "environmentally compatible" silicone-based antifouling synthesized in the laboratory and based on copper and silver on silica/titania oxides have been characterized, capable of replacing the non-ecological antifouling paints currently on the market. The texture properties and the morphological analysis of these powders with an antifouling action indicate that their activity is linked to the nanometric size of the particles and to the homogeneous dispersion of the metal on the substrate. The presence of two metal species on the same support limits the for-mation of nanometric species and therefore the formation of homogeneous compounds. The presence of the antifouling filler (specifically the one based on TiO2 and Ag) facilitates the achievement of a higher degree of cross-linking of the pure resin, and therefore a better compactness and completeness of the coating. This leads to a consequent better degree of adhesion to the tie-coat and therefore to the steel support used for the construction of the boats.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

The cornea is the optical window to the brain. Its optical and structural properties are responsible for optical transparency and vision. The shape, elasticity, rigidity or stiffness are given by its biomechanical properties, whose stability results in ocular integrity and intraocular pressure dynamics. Here, we report in vivo observation of structural changes and biomechanical alterations of the human cornea induced by acoustic wave pressure within the frequency range of 50-350 Hz and 90 dB of sound pressure level. Central corneal thickness (CCT) and eccentricity (e2) were measured using Scheimpflug imaging and biomechanical properties [corneal hysteresis (CH) and intraocular pressure (IOP] were assessed with air-puff tonometry in 6 young healthy subjects. At the specific 150 Hz acoustic frequency, the variation in CCT and e2 were of 0.058 and 7.33 µm, respectively. Biomechanical alterations were also observed in both IOP (decrease of 3.60 mmHg) and CH that showed an increase of 0.40 mmHg.

Most pathologies in emergency departments(EDs) can be detected with using non-invasive, extremely safe magnetic resonance imaging (MRI). MRI is highly sensitive to abnormality, so when compared to Computed Tomography(CT), a negative MRI far exceeds the value of a negative CT. This was a retrospective cohort study comparing resource utilization between September 2016 and September 2017 in a university hospital ED. Descriptive statistics are presented with frequency, percentage, mean, standard deviation, minimum and maximum values. A chi-square analysis was conducted to examine the relationships. Analyses were conducted using the SPSS 22.0 package program. In the ED, MRI is available 24/7. MRI was performed on 954 (479 female, 475 male) patients. A total of 212 cranial, 604 diffusion, 57 lumbar, 40 cervical, 38 dorsal, two abdominal, and one orbital MRIs were performed. In most groups, the average age was over 40, and the age distribution was similar (p = 0.12). There was no significant sex difference except for lumbar MRI. Lumbar MRI and diffusion MRI groups were admitted to the hospital mostly in the day hours (p = 0.03); in other groups, night and day admissions were almost the same. Neuroimaging takes the majority part of MRI examinations in our ED.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

CAR-T therapy has achieved considerable treatment success in hematologic tumors by using patient derived autologous αβ T cells. There is an impetus to broaden the applicability of this approach by using a third-party donor derived CAR-T cell product which has a potent anti-tumor function but a constrained GVHD property. In this study, CAR-T cells were prepared from Vγ9Vδ2 T cells expanded by using a novel prodrug PTA and their anti-tumor functions were assessed in conjunction with persistency, localization, and phenotype. γδ T cells were successfully transduced with a CAR specific to CEA with signaling domains of CD3ζ and CD28 (CEA.CAR-γδ T cells), and exhibited potent tumor killing function in vitro. In a xenograft mouse model, CEA.CAR-γδ T cells suppressed CEA+ tumor growth though a limited time window. CEA.CAR-γδ T cells persisted and accumulated in the tumor even after tumor progression, however, ex vivo analysis revealed that those recovered at different time points from PBMC, spleen and tumors gradually lost tumor reactivity as assessed by IFN-γ production. Provision of GITR co-stimulation enhanced anti-tumor function of CEA.CAR-γδ T cells, the result of which imposes additional measurers to be adopted in CAR-γδ T cells for an allogeneic adoptive immunotherapy.

Aging rate differs greatly between species, indicating that the process of senescence is largely genetically determined. Senescence evolves in part due to antagonistic pleiotropy (AP), where selection favors gene variants that increase fitness earlier in life but promote pathology later. Identifying the biological mechanisms by which AP causes senescence is key to understanding the endogenous causes of aging and its attendant diseases. Here we argue that the frequent occurrence of AP as a property of genes reflects the presence of constraint in the biological systems that they specify. This arises particularly because the functionally interconnected nature of biological systems constrains the simultaneous optimization of coupled traits (interconnection constraints), or because individual traits cannot evolve (impossibility constraints). We present an account of aging that integrates AP and biological constraint with recent programmatic aging concepts, including costly programs, quasi-programs, hyperfunction and hypofunction. We argue that AP mechanisms of costly programs and triggered quasi-programs are consequences of constraint, in which costs resulting from hyperfunction or hypofunction cause senescent pathology. Impossibility constraint can also cause hypofunction independently of AP. We also describe how AP corresponds to Stephen Jay Gould’s constraint-based concept of evolutionary spandrels, and argue that pathologies arising from AP are bad spandrels. Biological constraint is a missing link between ultimate and proximate causes of senescence, including diseases of aging. That this was not realized previously may reflect a combination of hyperadaptationism among evolutionary biologists, and the erroneous assumption by biogerontologists that molecular damage accumulation is the principal primary cause of aging.

Following the introduction of live-attenuated rotavirus vaccines in many countries, a notable reduction in deaths and hospitalizations associated with diarrhoea in children <5 years of age has been reported. There is growing evidence to suggest that live-attenuated vaccines also provide protection against other infections beyond the vaccine-targeted pathogens. These so called off-target effects of vaccination have been associated with the tuberculosis vaccine Bacille Calmette Guérin (BCG), measles, oral polio and recently salmonella vaccines, and are thought to be mediated by modified innate and possibly adaptive immunity. Indeed, rotavirus vaccines have been reported to provide greater than expected reductions in acute gastroenteritis caused by other enteropathogens, that have mostly been attributed to herd protection and prior underestimation of rotavirus disease. Whether rotavirus vaccines also alter the immune system to reduce non targeted gastrointestinal infections has not been studied directly. Here we review the current understanding of the mechanisms underlying off-target effects of vaccines and propose a mechanism by which the live-attenuated neonatal rotavirus vaccine, RV3-BB, could promote protection beyond the targeted pathogen. Finally, we consider how vaccine developers may leverage these properties to improve health outcomes in children, particularly those in low-income countries where disease burden and mortality is disproportionately high relative to developed countries.

(1) Background: This report examines the unique demands of off-road triathlon (XT) by presenting physiological, field, and race data from a national champion off-road triathlete using several years of laboratory and field data to detail training and race intensity. (2) Methods: Laboratory and field data were collected when the athlete was at near peak fitness and included oxygen consumption (VO2), heart rate (HR), power output (W), and blood lactate (BLC) during cycling and running, while HR, cycling W, and running metrics were obtained from training and race data files over a period of seven years. Intensity was described using % HR max zones (Z) 1 &lt; 75%, 2 = 75 - 87%, and Zone 3 &gt; 87%, and W. An ordinary least squares analysis was used to model differences between event types. (3) Results: Weather conditions were not different across events. XT events had twice the elevation change (p&lt;0.01) and two-three times greater W’ (p&lt; 0.001) than road triathlon (ROAD), but similar HR intensity profiles (max, avg, and zones); both events are predominately performed at &gt; Z2 or higher intensity. Championship XT events were longer (p&lt;0.01) , with higher kJ expenditure (p&lt;0.001). OLS modelling suggested three variables were strongly related (R2 = 0.84; p &lt; 0.0001) to cycling performance: event type (XT vs ROAD), total meters climbed, and total bike duration. Championship XT runs were slower than either regional (p&lt;0.05) or ROAD (p&lt;0.01) runs, but HR intensity profiles similar. OLS modelling indicates that slower running is linked to either greater total bike kJ expenditure (R2 = 0.57; p&lt;0.001), or total meters gained (R2 = 0.52; p&lt;0.001). Race simulation data support these findings but failed to produce meaningful differences in running. Conclusions: XT race demands are unique and mirror MTB and trail running demands. XT athletes must be mindful of developing anaerobic fitness, technical ability, and aerobic fitness, all of which contribute to off-road cycling economy. It is unclear whether XT cycling affects subsequent running performance different from ROAD cycling.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

Degenerative spinal cord (SC) compression is a frequent pathological condition with increasing prevalence throughout aging. Initial non-myelopathic cervical SC compression (NMDC) might progress over time into potentially irreversible degenerative cervical myelopathy (DCM). While quantitative MRI (qMRI) techniques demonstrated the ability to depict intrinsic tissue properties, longitudinal in-vivo biomarkers to identify NMDC patients who will eventually develop DCM are still missing. Thus, we aim to review the ability of qMRI techniques (such as diffusion MRI, diffusion tensor imaging (DTI), magnetization transfer (MT) imaging, magnetic resonance spec-troscopy (1H-MRS)) to serve as prognostic markers in NMDC. While DTI in NMDC patients con-sistently detected lower fractional anisotropy and higher mean diffusivity at compressed levels caused by demyelination and axonal injury, MT and 1H-MRS along with advanced and tract-specific diffusion MRI recently revealed microstructural alterations also rostrally pointing to Wallerian degeneration. Recent studies also disclosed significant relationship between micro-structural damage and functional deficits, assessed by qMRI and electrophysiology, respectively. Thus, tract-specific qMRI in combination with electrophysiology critically extend our under-standing of the underlying pathophysiology of degenerative SC compression and may provide predictive markers of DCM development for accurate patient management. However, the prog-nostic value must be validated in longitudinal studies.

Arrhythmogenic cardiomyopathy is a primary genetic disease caused by mutations of the desmosome genes. Ever since the introduction of new imaging criteria, like cardiovascular magnetic resonance, the diagnosis of arrhythmogenic cardiomyopathy is more challenging as left ventricular or biventricular variants may cause resemblance with other cardiomyopathies or myocarditis. Not only this, but they may also share an acute phase that might determine even more confusion and misdiagnosis which can influence prognosis and outcome. In this case report we present a 31-year-old patient with multiple clinical pictures: acute chest pain, new onset of heart failure and arrhythmia symptoms which determined a dynamic change in clinical diagnosis and management, ultimately taking into consideration arrhythmogenic cardiomyopathy. Through the article we try to emerge and explain common pathophysiological pathways shared by arrhythmogenic cardiomyopathy and other clinical entities with a special focus on inflammation. The final question remains: “If there is more than one heart disorder that eventually will lead to the same clinical picture, one could not but wonder if arrhythmogenic cardiomyopathy is rather a syndrome than a specific condition?”

Surface Plasmon Resonance (SPR) technology has been known as a powerful tool for studying biomolecular interactions because it offers real-time and label-free multiparameter analysis with high sensitivity. This article summarizes the results that have been obtained from the use of SPR technology in studying the dynamics of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) mutations. This paper will begin by introducing the working principle of SPR and the kinetic parameters of the sensorgram which include the association rate constant (ka), dissociation rate constant (kd), equilibrium association constant (KA), and equilibrium dissociation constant (KD). At the end of the section, we will summarize kinetic data on the interaction of SARS-CoV-2 with different variants with various ligands which were obtained from the results of SPR signal analysis. These affinity-related kinetic data are very useful both in drug discovery for therapeutic purposes and in the detection of SARS-CoV-2.

Conclusive evidence that specic long-term memory formation relies on den- dritic growth and structural synaptic changes has proven elusive. Connec- tionist models of memory based on this hypothesis are confronted with the so-called plasticity stability dilemma or catastrophic interference. Other fun- damental limitations of these models are the feature binding problem, the speed of learning, the capacity of the memory, the localisation in time of an event and the problem of spatio-temporal pattern generation. This paper suggests that the generalisation and long-term memory mechanisms are not correlated. Only the development and the improvement of the feature ex- tractors in the cortex involves structural synaptic changes. We suggest the long-term memory has a separate mechanism which involves protein synthe- sis to encode the information into the structure of these proteins. A model of memory should be capable of explaining the dierence between memorisation and learning. Learning has in our approach two dierent mechanisms. The generalisation in the brain is handled by the proper development of the links between neurons via synapses. The Hebbian learning rule could be applied only for this part of learning. Storing an internal ring pattern involves, in our approach, a new mechanism which puts the information regarding this ring pattern into the structure of special proteins in such a way that it can be retrieved later. The hypotheses introduced in this article includes a physiological assumption which has not been yet verified because it is not currently experimentally accessible. Keywords: Waves, Protein Synthesis, Resonance, Long Term Memory Preprint submitted to Neural Networks

Background: Left ventricular hypertrophy (LVH) may be due to different causes, ranging from benign secondary forms to severe cardiomyopathies. Transthoracic Echocardiography (TTE) and ECG are the first level examination for LVH diagnosis. Cardiac magnetic resonance (CMR) defines accurately LVH type, extent and severity. Objectives: to evaluate the diagnostic and prognostic role of CMR in patients with TTE and/or ECG evidence of LVH. Methods: We performed CMR in 300 consecutive patients with echocardiographic and/or ECG signs of LVH. Results: Overall, 275 patients had TTE evidence of LVH with initial suspicion of hypertrophic cardiomyopathy (HCM) in 132 (44%), cardiac amyloidosis in 41 (14%), hypertensive LVH in 48 (16%), aortic stenosis in 4 (1%), undetermined LVH in 50(16%). The initial echocardiographic diagnostic suspicion of LVH was confirmed in 172 patients (57.3%) and changed in 128 patients (42.7%, p<0.0001): the diagnosis of HCM increased from 44% to 71% of patients; hypertensive and undetermined LVH decreased significantly (respectively to 4% and 5%). CMR allowed a diagnosis in 41 out of 50 (82%) with undetermined LVH at TTE. CMR also identified HCM in 17 out of 25 patients with apparently normal echo but with ECG criteria for LVH. Finally, the reclassification of the diagnosis by CMR was associated with a change of survival risk of patients: after CMR reclassification no events occurred in patients with undetermined or hypertensive LVH. Conclusions: CMR changed echocardiographic suspicion in almost half of patients with LVH. In the subgroup of patient with abnormal ECG, CMR identified LVH (particularly HCM) in 80% of patients. This study highlights the indication of CMR to better characterize the type, extent and severity of LVH detected at echocardiography and suspected with ECG.

We study the application of Optimal Control Theory to Ion Cyclotron Resonance. We test the validity and the efficiency of this approach for the robust excitation of an ensemble of ions with a wide range of cyclotron frequencies. Optimal analytical solutions are derived in the case without any pulse constraint. A gradient-based numerical optimization algorithm is proposed to take into account limitation in the control intensity. The efficiency of optimal pulses is investigated as a function of control time, maximum amplitude and range of excited frequencies. A comparison with adiabatic and SWIFT pulses is done. On the basis of recent results in Nuclear Magnetic Resonance, this study highlights the potential usefulness of optimal control in Ion Cyclotron Resonance.

Bitumen aging is the major factor which contributes to the deterioration of the road pavement. Oxidation and volatilization are generally considered as the most important phenomena affecting aging in asphalt paving mixtures. The present study was carried to investigate whether various antioxidants provided by natural resources such as phospholipids, ascorbic acid as well as lignin from rice husk, could be used to reduce age hardening in asphalt binders. A selected bituminous material was modified by adding 2 % w/w of the anti-aging natural additives and subjected to accelerated oxidative aging regimes according to the Rolling Thin Film Oven Test (RTFOT) method. The effects of aging were evaluated based on changes in sol-gel transition temperature of modified bitumens measured through Dynamic Shear Rheology (DSR). Moreover, changes of Electron Paramagnetic Resonance (EPR) spectra were monitored on the bituminous fractions asphaltene and maltene separated by solvent extraction upon oxidative aging. The phospholipids-treated binder exhibited the highest resistance to oxidation and the lowest age-hardening effect compared to the other tested anti-oxidants. The combination of EPR and DSR techniques represents a promising method for elucidating the changes in associated complex properties of bitumen fractions promoted by addition of free radical scavengers borrowed by green resources.

The transportation sector stands out as California's primary contributor to greenhouse gas emissions, necessitating urgent action from government agencies to promote the adoption of low-carbon transportation (LCT) within the heavy-duty vehicles (HDV) and off-road equipment (ORE) sectors. This study conducts content analysis to delve into the impact of behavioral factors, specifically awareness and impression, on LCT adoption within these sectors. The analysis results are honed using a generative artificial intelligence (AI) tool. Positive associations emerge between the potential for LCT adoption and awareness, as well as factors linked to LCT (government incentives, environmental considerations). Notably, the study reveals that financial barriers and incentives hold greater significance for small-fleet organizations compared to their large-fleet counterparts. These findings offer actionable insights for government agencies to formulate targeted strategies, including mandates and incentives, tailored to the unique needs of organizations within the HDV and ORE sectors.

The increasing enhancement in the modulation accuracy of spatial light modulators has garnered significant attention towards real-time control technology for light fields based on these modulators. It has been empirically demonstrated that this technology possesses a remarkable capability to generate vector beams with arbitrary complex amplitude distributions. Nevertheless, past studies indicate that the generation of only one vector beam at a time has been observed. The simultaneous generation of numerous vector light fields can give rise to several challenges, including compromised picture quality, limited single mode operation, and intricate optical path configurations. In pursuit of this objective, we present a novel methodology that integrates the coding methodology of modified off-axis interferometric holography with the idea of optical superposition. This technique facilitates the concurrent generation of several vector beams. In this study, we present a demonstration of the simultaneous creation of twelve vector beams using a single spatial light modulator (SLM) as a proof of concept. Significantly, this technology has the ability to generate an unlimited quantity of vector light fields concurrently, under the assumption that the resolution of the SLM does not impose any limitations. The findings indicate that the imaging quality achieved by this technology is of a high standard. Furthermore, it is possible to separately control the beam waist radius, topological charge, polarization order, and extra phase of each beam.

Off-road vehicles and transportation are vital for agricultural economics, yet the transition to green energies is challenging. To make this application easier, a tool that enables the testing of heavy-duty off-road vehicles in various scenarios was created. Based on the methods of the World Harmonized Transient Cycle, a new Hybrid Operational Cycle that reflects the features of agricultural work was created and applied in a graphical model simulation. This was a newly developed methodology. The cycle and the model were based on gathered research data. A numerical model of a medium-power tractor with an internal combustion engine and a series-hybrid setup was created, and simulations were performed in Matlab and AVL Cruise. The research compared both diesel and hybrid vehicles in terms of their power production, fuel consumption, and efficiency in fieldwork and transportation scenarios. The research showed that a series-hybrid transmission can achieve an efficiency similar to that of tractors with a continuously variable transmission (CVT), but with the use of an electric powertrain, there is still an opportunity to exploit energy regeneration in transportation and under low-load conditions. The designed model also may be used for the development of control algorithms for hybrid drives and the improvement of the efficiency thereof.

Pipeline integrity is an important area of concern for the oil and gas, refining, chemical, hydrogen, carbon sequestration, and electric-power industries, due to the safety risks associated with pipeline failures. Regular monitoring, inspection, and maintenance of these facilities is therefore required for safe operation. Large standoff magnetometry (LSM) is a non-intrusive, passive magnetometer-based mea- surement technology that has shown promise in detecting defects (anomalies) in regions of elevated mechanical stresses. However, analyzing the noisy multi-sensor LSM data to clearly identify regions of anomalies is a significant challenge. This is mainly due to the high frequency of the data collection, mis-alignment between consecutive inspections and sensors, as well as the number of sensor measurements recorded. In this paper we present LSM defect identification approach based on ma- chine learning (ML). We show that this ML approach is able to successfully detect anomalous readings using a series of methods with increasing model complexity and capacity. The methods start from unsupervised learning with "point" methods and eventually increase complexity to supervised learning with sequence methods and multi-output predictions. We observe data leakage issues for some methods with randomized train/test splitting and resolve them by specific non-randomized splitting of training and validation data. We also achieve a 200x acceleration of support-vector classifier (SVC) method by porting computations from CPU to GPU leveraging the cuML RAPIDS AI library. For sequence methods, we develop a customized Convolutional Neural Network (CNN) architecture based on 1D convolutional filters to identify and characterize multiple properties of these defects. In the end, we report the scalability of the best-performing methods and compare them, for viability in field trials.

Most of α-thalassemia cases are caused by deletions of the structural α-globin genes. The degree of microcytosis and hypochromia has been correlated with the number of affected α-globin genes, suggesting a promising role of hematologic parameters as predictive diagnostic tools. However, specific cut-off points for these parameters to discriminate between the different subtypes of α-thalassemia remain to be clearly defined. Six hematologic parameters (total number of erythrocytes, hemoglobin concentration, mean corpuscular volume, mean corpuscular hemoglobin, mean corpuscular hemoglobin concentration and red cell distribution width) were evaluated in 174 cases of deletional α-thalassemia (92 heterozygous α+ thalassemia, 39 homozygous α+ thalassemia, 34 heterozygous α0 thalassemia and 9 cases of Hb H disease). A good correlation between the number of deleted alpha genes and MCV (r = -0.672, p<0.001), MCH (r = -0.788, p<0.001) and RDW (r = 0.633, p<0.001) was observed. The deletion of at least two alpha genes in adult individuals with microcytosis without iron deficiency and normal values of Hb A2 and Hb F should be discarded when MCH levels are lower than 23.15 pg. Furthermore, MCH <21.90 pg and/or MCV <70.80 fL are strongly suggestive of the presence of one α0 allele. Finally, an accurate presumptive diagnosis of Hb H disease can be made if both RDW ≥20% and MCH <18.45 pg are seen.

In airborne sensor networks (ASNs), the media access control (MAC) protocol is facing with serious unfairness problem due to the traditional protection mechanism of air-to-air communications among aircrafts. Actually by using the binary exponential back-off algorithm at high traffic loads to minimize collisions among users, the latest successful node can always benefit from this kind of MAC to obtain channel resources. Moreover, when taking the existence of the hidden nodes in ASNs into account, the inaccurate traffic load information will further aggravate the system’s unfairness. In this paper, a neighbor-channel-aware (NCA) protocol is proposed to improve the fairness of MAC protocol in ASNs. In the proposal, the NCA frame is firstly added and exchanged between neighbor nodes periodically, which helps to resolve the inaccurate traffic load information, so as to avoid reducing the probability of successful message transmission. Then a traffic-loading based back-off algorithm is involved to make the neighbor nodes cooperatively adjust the inter-frame space (IFS) interval to further reduce the unfairness. The simulation results show that, the proposed MAC protocol can guarantee the satisfied fairness, simultaneously avoiding heavy network overloads to protect key messages’ successful transmissions in ASNs.

Lung cancer is the leading cause of cancer related mortality worldwide. In order to improve its overall survival, early diagnosis is required. Since current screening methods still face some pitfalls, such as high false positive rates for low-dose computed tomography, researchers are still looking for early biomarkers to complement existing screening techniques in order to provide a safe, faster and more accurate diagnosis. Biomarkers are biological molecules found in body fluids, such as plasma, that can be used to diagnose a condition or disease. Metabolomics has already shown to be a powerful tool in the search for cancer biomarkers since cancer cells are characterised by impaired metabolism, resulting in an adapted plasma metabolite profile. The metabolite profile can be determined using nuclear magnetic resonance, or NMR. Although metabolomics and NMR metabolite profiling of blood plasma are still under investigation, there is already evidence for its potential for early-stage lung cancer diagnosis, therapy response, and follow-up monitoring. This review highlights some key breakthroughs in this research field, where the most significant biomarkers will be discussed in relation with their metabolic pathways and in light of the altered cancer metabolism.

An association between subtle changes in T2 white matter hyper-intense signals (WMHS) de-tected in fetal brain magnetic resonance imaging (fbMRI) and congenital cytomegalovirus (CMV) infection has been established. The research aim of this study is to compare children with congenital CMV infection with neurodevelopment outcome and hearing deficit with and with-out WMHS in a prospective historic cohort of 58 fbMRIs. Of these, WMHS was detected in 21. The median infection week of the WMHS group was earlier than the normal fbMRI group (8 and 17 weeks of gestation respectively). The proportion of infants treated with valganciclovir in the WMHS group was distinctly higher. Hearing impairment was not significantly different be-tween the groups. VABS scores in all 4 domains were within normal range in both groups. The median score of the motor skills corrected for week of infection was better in the WMHS group. A multivariate analysis using week of infection interaction variable of WMHS and valganciclo-vir treatment showed better motor score outcomes in the valganciclovir treatment group despite earlier week of infection. WMHS was not associated with neurodevelopmental outcome and hearing deficit. In our cohort valganciclovir treatment may have a protective effect on fetuses with WMHS by improving neurodevelopment outcome.

This study aimed to evaluate potential posttreatment changes in ADC values within the tissue surrounding the enhancing lesion, particularly in areas not exhibiting MRI characteristics of in-volvement. Additionally, the objective was to investigate the correlation between ADC values, treatment response, and survival outcomes in individuals diagnosed with gliomas. This retrospective study included a total of 49 patients that underwent either stereotactic biopsy or maximal surgical resection. Histologically confirmed as Grade III or IV gliomas, all cases adhered to the 2016 and 2021 WHO classifications, with subsequent radio-chemotherapy administered post-surgery. Patients were divided into two groups: short and long survival group. Baseline and follow-up MRI scans were obtained on a 1.5T MRI scanner. Two ROI circles were positioned near the enhancing area, one ROI in the NAWM ipsilateral to the neoplasm and another symmetrically in the contralateral hemisphere on ADC maps. At follow-up there was a significant difference in both ipsilateral and contralateral NAWM be-tween the two groups, -0.0857 (p=0.004) and -0.0607 (p=0.037), respectively. There was a weak negative correlation between survival and ADC values in ipsilateral and contralateral NAWM at the baseline with the correlation coefficient -0.328 (p=0.02) and -0.302 (p=0.04), respectively. The correlation was stronger at the follow-up. The findings indicate that ADC values in normal appearing white matter (NAWM) may function as a prognostic biomarker in patients with diffuse gliomas.

MicroRNAs are small ribonucleotides which act as key gene regulators. Their altered expression is often associated with onset and progression of several human diseases, including cancer. Given their potential use as biomarkers, there is a need to find detection methods of microRNAs suitable for use in clinical setting. Field Effect Transistor based biosensors (bioFETs) appear to be valid tools to detect microRNAs, since they may reliably quantitate the specific binding between the immobilized probe and free target in solution through an easily detectable electrical signal. We have investigated the detection of human microRNA 155 (miR-155) using an innovative cap-turing probe constituted by a synthetic peptide nucleic acid (PNA), which has the advantage to form a duplex even at ionic strengths approaching the physiological conditions. With the aim to develop an optimized BioFET setup, the interaction kinetics between miR-155 and the chosen PNA was preliminary investigated by Surface Plasmon Resonance (SPR). By exploiting both these results and our custom-made bioFET system, we were able to attain a low-cost, real-time, label-free, highly specific detection of miR-155 in the nano-molar range.

Abstract: Aim: Biofields combine many physiological levels both spatially and temporally. These biofields reflect naturally resonant forms of synaptic energy reflected in growing and spreading waves of brain activity. The study desires to theoretically understand better how resonant continuum waves may be reflective of consciousness, memory, and thought. Background: The metabolic processes that maintain animal cellular and physiological function are enhanced by physiological coherence. Internal biological system coordination and sensitivity to particular stimuli and signal frequencies are two aspects of coherent physiology. There exists significant support for the notion that exogenous biologically and non-biologically generated energy entrains human physiological systems. All living things have resonant frequencies that are either comparable or coherent, therefore eventually all species will have a shared resonance. An organism's biofield activity and resonance are what support its life and allow it to react to stimuli. Methods: As the naturally resonant forms of synaptic energy are growing and spreading waves of brain activity, The temporal and spatial frequency of waves are effectively regulated by a time delay (T) in inter-layer signals in a layered structure that mimics the structure of the mammalian cortex. From ubiquitous noise, two different types of waves can arise as a function of T. One is coherent, and as T rises, so does its resonant spatial frequency. Results: Continued growth eventually causes both the wavelength and the temporal frequency to abruptly increase. Two waves expand simultaneously and randomly interfere in an area of T values as a result. Conclusion: We suggest that because of this extraordinary dualism, which has its roots in the phase relationships of amplified waves, coherent waves are essential for memory retrieval whereas random waves represent original cognition.

Motivated by the intriguing discovery of $X(6900)$ by LHCb Collaboration, we undertake a comprehensive study of the $s\bar{s}s\bar{s}$ tetraquark system in positive parity, employing the Gaussian expansion within the chiral quark model method. We consider two structures, diquark-antidiquark ($ss$-$\bar{s}\bar{s}$) structure and meson-meson ($s\bar{s}$-$s\bar{s}$)strcuture, encompassing all conceivable color and spin configurations. Despite the absence of bound states in our calculations, we have identified potential resonant states with $J^P=0^{+}$, namely $R(0,2150)$ and $R(0,2915)$, as well as a resonant state with $J^P=1^{+}$ denoted as $R(1,2950)$, and a resonant state with $J^P=2^{+}$ denoted as $R(2,2850)$, utilizing the real-scaling method. Through a comparison of their energies and widths, we propose that $R(0,2915)$ and $R(1,2950)$ may share characteristics with $X(6900)$, while $R(0,2150)$ could be a promising experimental candidate for $f_0(2100)$. We strongly advocate for experimental investigations to shed light on the existence and properties of these resonant states.

Embryological development of pancreas is a complex phenomenon and therefore, it can have multiple developmental aberrations. Fortunately, majority of these pancreatic ductal anomalies are asymptomatic with no clinical relevance and are incidentally detected during diagnostic cross sectional imaging or endoscopic retrograde cholangiopancreatography (ERCP) or autopsy. Occasionally, pancreatic duct anomalies can result in symptoms like abdominal pain or recurrent pancreatitis. Also, accurate pre-operative diagnosis of ductal anomalies can prevent inadvertent duct injury during surgery. Conventionally, ERCP had been used for accurate diagnosis of pancreatic duct anomalies. However, because of being invasive and associated with risk of pancreatitis, it has been replaced with magnetic resonance cholangiopancreatography (MRCP). MRCP has demonstrated high sensitivity and specificity for diagnosis of ductal anomalies which can be further improved with use of secretin enhanced MRCP. Endoscopic ultrasound (EUS) is a new diagnostic and interventional tool in the armamentarium of endoscopists and has demonstrated promising results in detection of pancreatic duct variations and anomalies. In this article, we will focus on the role of EUS in diagnosis of various pancreatic duct anomalies.

Background and objectivesː Physical examination is the predominant method for evaluating pelvic floor defects. Magnetic Resonance Imaging (MRI) is a radiological technique useful to identify the underlying defects of pelvic floor structures that require surgery. The primary aim was to find correspondence between the clinical and radiological staging of pelvic organ prolapse (POP) before and after vaginal surgery. A secondary endpoint was to investigate, through clinical and MRI findings if surgery influences continence mechanisms. Finally, we reported changes in the quality of life in women who underwent surgery for prolapse. Materials and methodsː Twenty-five women with prolapse stage ≥ 2 POP-Q were recruited in this prospective study. They underwent preoperative clinical examination, MRI at rest and under the Valsalva maneuver, and quality of life questionnaires. Three months after vaginal surgery they repeated clinical and radiological evaluation. Resultsː Twenty women completed the study. Both clinical and MRI evaluations showed an improvement in prolapse and symptoms after surgery. There were some discrepancies between clinical and radiological staging. MRI parameters did not show differences between pre and postoperative at rest; under the Valsalva maneuver instead, the measurements changed after surgery. Continence was not worsening by the widening of the vesicourethral angle. Patients reported improvement in quality of life. Conclusionsː MRI is an accurate and objective method to define the stage of prolapse but the clinical evaluation alone is sufficient to stage prolapse before surgery and evaluate the result at follow-up. It is an accurate method to visualize some pelvic structures that can be compromised because of pelvic organ prolapse. MRI showed that vaginal surgery doesn’t affect continence mechanisms.

Breast cancer is the foremost common in women, and its early diagnosis will help treat and increase patients' survival. This review article aims to studies on recent findings of standard imaging techniques and their characteristics for breast cancer diagnosis and recent nanoparticles (NPs) which are used for breast cancer detection. Herein, The search was performed in the literature through scientific citation websites, including Google Scholar, PubMed, Scopus, and Web of Science until May 2023. A comprehensive study on different imaging modalities and NPs for breast cancer diagnosis is reviewed, and their successes, challenges, and limitations are discussed.

Background: We designed a prospective study of diagnostic accuracy which compared pelvic MRI and 3D-EAUS versus pelvic MRI alone in the preoperative evaluation and postoperative outcomes of patients with perianal fistulas. Methods: The sample size was 72 patients and was divided into two imaging groups. MRI alone was performed in the first group. Both MRI and 3D-EAUS were performed in a parallel fashion in the second group. Surgical exploration took place after two weeks and was the standard reference. Park’s classification, presence of a concomitant abscess or a secondary tract and location of the internal opening were recorded. All patients were re-evaluated for complete fistula healing and fecal incontinence six months postoperatively. All the collected data was subjected to statistical analysis. Results: Group MRI included 36 patients with 42 fistulas. Group MRI + 3D-EAUS included 36 patients with 46 fistulas. The adjusted sensitivity and negative predictive value were 1.00 for most fistula types in the group of combined imaging. The adjusted specificity improved on intersphincteric fistulas in the same group. The adjusted balanced accuracy improved on all fistula types, except for rectovaginal. The combination of imaging methods showed improved diagnostic accuracy only on the detection of a secondary tract. Healing rate at six months was 100%. Fecal incontinence at six months didn’t present a statistically significant difference between the two groups (Fisher's exact test p-value &gt; 0.9). Patients with complex perianal fistulas had a statistically significant higher probability to undergo a second surgery (x² test p-value=0.019). Conclusion: The combination of pelvic MRI and 3D-EAUS showed improved metrics of diagnostic accuracy and should be used in the preoperative evaluation of all patients with perianal fistulas, especially in those with complex type.

This study aimed to evaluate contrast-enhanced mammography (CEM) and compare breast lesions on CEM and breast magnetic resonance imaging (MRI) using 5 features. We propose to create a flowchart for BI-RADS classification of breast lesions on CEM based on the Kaiser score (KS) flowchart for breast MRI. Included were 68 subjects (women and men; median age 61.4 ± 11.6 years) who were suspected of having a malignant process in the breast based on digital mammography (MG) findings. The patients underwent breast ultrasound (US), CEM, MRI, and biopsy of the suspicious lesion. There were 47 patients with malignant lesions confirmed by biopsy and 21 patients with benign lesions, for each of which a KS was calculated. In the patients with malignant lesions, the MRI-derived KS was 9 (IQR 8-9), its CEM equivalent was 9 (IQR 8-9), and BI-RADS was 5 (IQR 4-5). In patients with benign lesions, MRI-derived KS was 3 (IQR 2-3), its CEM equivalent was 3 (IQR 1.7-5), and BI-RADS was 3 (IQR 0-4). There was no significant difference between the ROC-AUC of CEM and MRI (P=0.749). In conclusion, there were no significant differences in KS results between CEM and breast MRI. The KS flowchart is useful for evaluating breast lesions on CEM.

Brain development during the prenatal period is rapid and unparalleled by any other time during development. Biological systems undergoing rapid development are at higher risk for disorganizing influences. Therefore, certain prenatal exposures impact brain development, increasing risk for negative neurodevelopmental outcome. While prenatal exposures have been associated with cognitive and behavioral outcomes later in life, the underlying macroscopic brain pathways remain unclear. Here, we review studies investigating the association between prenatal exposures and infant brain development focusing on prenatal exposures via maternal physical health factors, maternal mental health factors, and maternal drug and medication use. Further, we discuss the need for studies to consider multiple prenatal exposures in parallel and suggest future directions for this body of research.

Abstract We aim to describe the diagnosis and surgical management of urinary tract endometriosis (UTE). We detail current diagnostic tools including advanced transvaginal ultrasound, magnetic resonance imaging, and surgical diagnostic tools such as cystourethroscopy. While discussing surgical treatment options, we emphasize the importance of an interdisciplinary team, for complex cases that involve the urinary tract. While bladder DE is more straightforward in its surgical treatment, ureteral DE requires a high level of surgical skill. Specialists should be aware of the important entity of UTE due to the serious health implications for women. When UTE exists, it is important to work within a interdisciplinary radiological and surgical team.

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which is difficult to be found in naturally available materials. The acoustic metamaterials have demonstrated to exhibit excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials' recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field is discussed as well.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

The industry of the counterfeit goods is one of the largest underground business in the world and it is rapidly growing. Counterfeits can lead not only to loss of profit for honest producers but also have a negative impact on consumers who receive poor quality goods at an excessive price and may be exposed to health damages and safety issues. Perfume industry is constantly exposed to the problem of counterfeits with the fast developing parallel market of inspired perfumes being an important issue. It prompts for the identification of methods that classify the quality of this type of products. In this paper the application of proton nuclear magnetic resonance spectroscopy is employed for the authentication of perfumery products for the first time. Molecular composition of several types of authentic brand fragrances for women were compared with their cheaper inspired equivalents and fake products. Our approach offers the prospect of a fast and simple method for discrimination and counterfeit detection of perfumes using 1H NMR spectroscopy.

Background: Diabetes is among the most prevalent diseases worldwide, of all the affected individuals a significant proportion of the population remains undiagnosed because of a lack of specific symptoms early in this disorder and inadequate diagnostics. Diabetes and its associated sequela, i.e., comorbidity are associated with microvascular and macrovascular complications. As diabetes is characterized by an altered metabolism of key metabolites and regulatory pathways. Metabolic phenotyping can provide us with a better understanding of the unique set of regulatory perturbations that predispose to diabetes and its associated comorbidities. Methodology: The present study utilizes the analytical platform NMR spectroscopy coupled with Random Forest statistical analysis to identify the discriminatory metabolites of diabetes (DB) and diabetes-related comorbidity (DC) along with the healthy control (HC) subjects. A combined and pairwise analysis was performed, between the serum samples of HC (n=50), and DB (n=38), and DC (n=35) individuals to identify the discriminatory metabolites responsible for class separation. The perturbed metabolites were further rigorously validated using t-test, AUROC analysis to examine the statistical significance of the identified metabolites. Results: The DB and DC patients were well discriminated from HC. However, 15 metabolites were found to be significantly perturbed in DC patients compared to DB, the identified panel of metabolites are TCA cycle (succinate, citrate), methylamine metabolism (trimethylamine, methylamine, betaine), -intermediates; energy metabolites (glucose, lactate, pyruvate); and amino acids (valine, arginine, glutamate, methionine, proline and threonine). The metabolites were further used to identify the perturbed metabolic pathway and correlation of metabolites in DC patients. Conclusion: The 1H NMR metabolomics may prove a promising technique to differentiate and predict diabetes and its comorbidities on their onset or progression by determining the altered levels of the metabolites in serum.

The effects of the climate crisis are affecting ecosystems at different scales and magnitudes. This paper focuses on a massive Mediterranean mussel die-off observed along the middle Italian Adriatic coast in the summer of 2022. We considered the possible environmental causes of this phenomenon and carried out a climatic analysis of the last decade. We performed field surveys in different locations along a 16 Km coastal stretch (from Martinsicuro (TE) on the South, to Grottammare (AP) on the North). The study area includes two marine Sites of Community Importance under the European Natura 2000 network. The mussels die-off has interested practically all the natural mussel-beds colonizing the study area. Mussels are sessile filter-feeding organisms inhabiting the intertidal zone, therefore, are highly exposed to variations in environmental conditions such as temperature and nutrient load. We discuss the possible causes of this die-off, proposing that high temperature and the scarce availability of food acted simultaneously as stress factors, generating local unsustainable living conditions for this species.

We developed and applied a method for characterizing bacterial promoters genome-wide by in vitro transcription coupled to transcriptome sequencing specific for native 5’-ends of transcripts. This method called ROSE (Run-Off transcription/RNA-SEquencing), only requires chromosomal DNA, ribonucleotides, RNA polymerase (RNAP) core enzyme, and a specific sigma factor, recognizing the corresponding promoters, which have to be analyzed. ROSE was performed on E. coli K-12 MG1655 genomic DNA using E. coli RNAP holoenzyme (including σ70) and yielded 3,226 transcription start sites, 2,167 of which were also identified in in vivo studies, and 598 were new. Many new promoters not yet identified by in vivo experiments might be repressed under the tested conditions. Complementary in vivo experiments with E. coli K-12 strain BW25113 and isogenic transcription factor gene knockout mutants of fis, fur, and hns were used to test this hypothesis. Comparative transcriptome analysis demonstrated that ROSE could identify bona fide promoters that were apparently repressed in vivo. In this sense, ROSE is well-suited as a bottom-up approach for characterizing transcriptional networks in bacteria and ideally complementary to top-down in vivo transcriptome studies.

Our knowledge of physics and chemistry is relatively well defined. Results from that knowledge are predictable as, largely, are those of their technical offspring such as electrical, chemical, me-chanical and civil engineering. By contrast biology is relatively unconstrained and unpredictable. A factor common to all areas is the trade-off, which provides a means of defining and quantifying a problem and, ideally, its solution. In order to understand the anatomy of the trade-off and how to handle it, its development (as the dialectic) is tracked from Hegel and Marx to its implementa-tion as dialectical materialism in Russian philosophy and TRIZ, the Theory of Invention. With the ready availability of mathematical techniques, such as multi-objective analysis and the Pareto set, the trade-off is well-adapted to bridging the gaps between the quantified and the unquantifiable, allowing modelling and the transfer of concepts by analogy. It is thus an ideal tool for biomimet-ics. An intracranial endoscope can be derived with little change from the egg-laying tube of a wood wasp. More complex transfers become available as the technique is developed. Most im-portant, as more trade-offs are analyzed, their results are stored to be used again in the solution of problems. There is no other system in biomimetics which can do this.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

This contribution is an attempt to reconstruct the favorable atmosphere that prevailed in Lau-sanne in 1986-87 and provided the backdrop of our invention of two-dimensional ion cyclotron resonance mass spectroscopy (2D ICR-MS). To avoid a self-centered histoire d’ancien combattant, we shall try to emphasize the context, the contributions of key players within our nascent research group at UNIL and the established group of Tino Gäumann at EPFL, the role of external speakers, and the open atmosphere that was not yet polluted by bibliometrics, obsessive concern with im-pact factors, and top-down management of research. We shall also explain why the idea of 2D ICR-MS has been ignored for many years and still has a limited impact: different scientific cul-tures in the ICR and NMR communities, different concerns with fundamental vs. applied research, different status of theory and numerical simulations, different levels of commitment of instrument manufacturers, not to mention many theoretical problems that appear to be at least as challenging in ICR as in NMR.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

This article discusses the use of a hand held electronic nose to obtain information on the presence of some aromatic defects in natural cork stoppers, such as haloanisoles, alkylmethoxypyrazines and ketones. The proposed prototype has been developed as an instrumentation system with up to eight commercial gas sensors. Machine learning algorithms such as k-nearest neighbors and artificial neural networks has been used. The use of this system tries to improve the current aromatic defect detection process in the cork stopper industry, which is done by gas chromatography or human test panels.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Understanding biological mechanisms that regulate emergence of viral diseases, in particular those events engaging cross-species pathogens spillover, are becoming increasingly important in Virology. Species barrier jumping has been extensively studied in animal viruses, and the critical role of a suitable intermediate host in animal viruses-generated human pandemics is highly topical. However, studies on host jumping involving plant viruses have been focused on shifting intra-species, leaving aside the putative role of “bridge hosts” in facilitating interspecies crossing. Here, we take advantage of several VPg mutants, derived from a chimeric construct of the potyvirus Plum pox virus (PPV), analysing its differential behaviour in three herbaceous species. Our results showed that two VPg mutations in a Nicotiana clevelandii-adapted virus, emerged during adaptation to the bridge-host Arabidopsis thaliana, drastically prompted partial adaptation to Chenopodium foetidum. Although, both changes are expected to facilitate productive interactions with eIF(iso)4E, polymorphims detected in PPV VPg and the three eIF(iso)4E studied, extrapolated to a recent VPg:eIF4E structural model, suggested that two adaptation ways can be operating. Remarkably, we found that VPg mutations driving host-range expansion in two non-related species, not only are not associated with cost trade-off constraints in the original host, but also improve fitness on it.

Mid-tropospheric cut-off low (COL) pressure systems are linked to severe weather, heavy rainfall and extreme cold conditions over South Africa. They often result in floods and snowfalls in winter disrupting economic activities. This paper examines the evolution and circulation patterns associated with severe COLs over South Africa. We evaluate the performance of the 4.4 km Unified Model (UM) which is currently used operationally by the South African Weather Service to simulate daily rainfall. Circulation variables and precipitation simulated by the UM were compared against ECMWF’s ERA Interim reanalyses and GPM precipitation at 24-hour timesteps. We present five recent (2016-2019) severe COLs that had high impact and found higher model skill when simulating heavy precipitation during the initial stages than the dissipating stages of the systems. A key finding was that the UM underestimated precipitation mainly due to inaccurate placing of COL centers and areas of heavy rainfall by up to 5° of latitude away from the actual location, due to the poor formulating of cumulus and microphysics schemes in the model. Understanding the performance and limitations of the UM model in simulating COL characteristics can benefit severe weather forecasting and contribute to disaster risk reduction in South Africa.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

There have been several cases of large-scale wind generators (WGs) tripping off caused by untimely fault removing in recent years. Currently, the discoordination between the box-type transformer fuse protection (BTFP) and two-section collecting line current protection (CLCP) brings a security risk to wind farm. In order to ensure the selectivity, the first section (Sec-I) CLCP should be set a enough interval that is longer than the fuse melting time, and another interval is set for the Sec-II CLCP, which weakens the speed of the CLCP. When a fault occurs on the collecting line, there is no doubt that WGs cannot work too long in abnormal operation, which may cause WGs to be placed off the grid. For a power system with high penetration of wind power, large-scale WGs tripping off will cause a great power shortage, and affect the stability of the power system. The selectivity and sensitivity of the CLCP is analyzed in detail to make the CLCP speed better. Considering the fault ride-through ability of WGs, the fault clear time is an important factor to lead to large-scale WGs tripping off. Two main works are done in this paper. The first is to accelerate the speed of the Sec-I CLCP though reducing the protection zone. Another one is introduce the risk assessment module into the CLCP, which not only improve the speed of the CLCP but also ensure the safety of the wind farm during faults. According to the deference in trip-off causes of WGs, the matching functions are created to assess the trip-off risk of WGs on the spot. In the case of fault, the trip-off risk indicators of WGs are timely updated to data sharing center and open to the CLCPs. The set of risk indicators is divided into several subsets according to the risk range. The dynamic changes of the subsets during fault help to improved CLCP scheme. This scheme can accelerate protection speed based on the increasing risk of large-scale WGs tripping off in wind farms. Compared with traditional CLCP, this approach can make the CLCP combines selectivity and speed better based on the analysis of the ride- through ability of WGs.

Risk stratification for malignant ventricular arrhythmias and sudden cardiac death is a daunting task for physicians in daily practice. Multiparametric mapping sequences obtained via cardio-vascular magnetic resonance imaging can improve the risk for malignant ventricular arrhythmias by unveiling the presence of pathophysiological pro-arrhythmogenic processes. However, their employment in clinical practice is still restricted. The present review explores the current evidence supporting the association between mapping abnormalities and the risk of ventricular arrhyth-mias in several cardiovascular diseases. The key message is that further clinical studies are needed to test the additional value of mapping techniques beyond conventional cardiovascular magnetic resonance imaging for selecting patients eligible for an implantable cardioverter defibrillator.

MIPs inspired by antigen-antibody interactions have received substantial interest as a biomimetic artificial receptor system in environmental applications. Herein, we present a molecularly imprinted surface plasmon resonance (SPR) sensor integrated with Au nanoparticles for the identification of bisphenol A (BPA), an endocrine-disrupting chemical. The synthetic wastewater samples were analyzed to ensure the method's reliability and feasibility. Under ideal conditions, the suggested approach performed well in terms of analytical performance to BPA, with a wide linear range of 0.1 to 10 ppb and LOD of 10 ng/L. The sensor results and the Langmuir adsorption model have good agreement. It has also been shown that repeated use of the biosensor can be achieved. According to selectivity studies, BPA adsorbed within the imprinted cavities favorably compared to 4-nitrophenol and phenol. The produced BPA-imprinted SPR sensor provides improved sensitivity based on the signal amplification strategy, unconjugated sensing without the need for labeling, real-time sensing, low sample consumption rates, quantifiable assessment, and very good kinetic rate constant calculation in actual samples. Also, because the produced sensor is reusable with relative standard deviations (RSD)<1.25, indicating the sensor's accuracy, the SPR-based biomimetic BPA sensor is simple to practice and may be an economical option.

Axions can be stimulated to decay to photons by ambient photons of the right frequency or by photons from decay of neighboring axions. If the axion density is high enough the photon intensity can be amplified, which is a type of lasing or an axion maser. Here we review the astrophysical situations where axion lasing can appear and possibly be detected.

A tunable near-infrared surface plasmon resonance (SPR) biosensor based on gate-controlled graphene plasmons is investigated theoretically. The novel characteristics of chemical potential sensing make the proposed sensor promising in the application of ultra-sensitive and highly specific biosensing technology. The sensitivity of chemical potential sensing in wavelength interrogation mode can be calculated to be 1.5, 1.89, 2.29, 3.21, 3.73 and 4.68 nm/meV respectively at the central wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. The much smaller full width half maximum (FWHMs) comparing with that of 2D nanomaterial-enhanced metal SPR sensors indicates higher figure of merit. The sensitivity of chemical potential sensing in gate voltage interrogation mode also can be calculated to be 156.9822, 143.6147, 131.0779, 111.0351, 101.3415 and 90.6038 mV/meV respectively at the incident wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. It can be estimated theoretically that the limit of detection (LOD) in DNA sensing of the proposed sensor can reach femtomolar level and even attomolar level, comparable to and even lower than that of 2D nanomaterial-enhanced metal SPR sensors with AuNPs as a sensitivity enhancement strategy. The feasibility of preparation and operation of this new concept SPR biosensor is also analyzed and discussed.

Rectal cancer presents significant diagnostic and therapeutic challenges, with neoadjuvant therapy playing a pivotal role in improving resectability and patient outcomes. MRI serves as a critical tool in assessing treatment response. However, differentiating viable tumor tissue from therapy-induced changes on MRI remains a complex task. In this comprehensive review, we explore treatment options for rectal cancer based on resectability status, focusing on the role of MRI in guiding therapeutic decisions. We delve into the nuances of MRI-based evaluation of treatment response following neoadjuvant therapy, with particular attention to emerging techniques like radiomics. Drawing from current literature and insights, we provide essential recommendations for post-neoadjuvant therapy management in rectal cancer, all within the context of MRI-based findings.

The Atlantic puffin is a medium-sized seabird with black and white plumage and orange feet. It is distributed mainly along the northern Atlantic Ocean and due, among other reasons, to human activities, it is in a threatened situation and classified as a vulnerable species according to the International Union of Conservation of Nature (IUCN). In this study, we used a total of 20 carcasses of juvenile Atlantic puffins to perform anatomical cross sections and magnetic resonance images. Thus, an adequate description of the head was made, providing valuable information that could be helpful as a diagnostic tool for veterinary clinicians, who increasingly treat these birds in zoos, rehabilitation centers and even in the wild.

Simple summary: The noninvasive differentiation of hepatocellular carcinoma (HCC) from intrahepatic cholangiocarcinoma (ICC) remains challenging. In recent years, the number of studies on the application of radiomics in liver cancer has grown dramatically. However, there have been very few studies on the differentiation of HCC from ICC based on multisequence magnetic resonance imaging (MRI) radiomics. This study aimed to investigate the efficacy of a radiomic model based on preoperative fat suppression T2-weighted imaging (FS-T2WI) and dynamic contrast-enhanced MRI features in the arterial phase (A) and portal venous phase (P) for the differentiation of HCC from ICC. Abstract: The purpose of this study was to investigate the efficacy of magnetic resonance imaging (MRI) radiomics in differentiating hepatocellular carcinoma (HCC) from intrahepatic cholangiocarcinoma (ICC). The clinical and MRI data of 129 pathologically confirmed HCC cases and 48 ICC cases from April 2016 to December 2021 at the Affiliated Hospital of North Sichuan Medical College were retrospectively analyzed. Included cases were randomly divided at a ratio of 7:3 into a training group of 124 cases (90 HCC cases and 34 ICC cases) and a validation group of 53 cases (39 HCC cases and 14 ICC cases). Radiomic features were extracted from axial fat-suppression T2-weighted imaging (FS-T2WI) and axial arterial-phase (A) and portal-venous-phase (P) dynamic contrast-enhanced MRI sequences, and the corresponding datasets were generated. The least absolute shrinkage and selection operator (LASSO) method was used to select the best radiomic features. Logistic regression was used to establish a radiomic model for each sequence (FS-T2WI, A, and P models) and a joint model (M model) integrating the radiomic features of all the sequences. The performance of each model was evaluated using the area under the receiver operating characteristic curve (AUC). The AUC of the FS-T2WI, A, P, and M models for distinguishing HCC from ICC was 0.693, 0.863, 0.818, and 0.914 in the training group and 0.690, 0.784, 0.727, and 0.802 in the validation group, respectively. The results of this study suggest that MRI-based radiomics may help noninvasively differentiate HCC from ICC. The model integrating the radiomic features of multiple sequences showed further improvement in performance.

Resonant light scattering by mesoscale dielectric spheres has received enormous attention and found many interesting applications. The recently emerged field of Mesotronics provides novel opportunities for wavelength-scaled optics and new fundamental aspects are still being uncovered. It has recently been demonstrated that high-order Mie resonances can be excited in homogeneous low-dissipation mesoscale dielectric spheres, leading to the generation of intense magnetic fields. This Letter describes a simple and effective way to drastically enhance the superresonance effect. Proof-of-principle results for the first time show that yet one more novel phenomenon of increasing the intensity of the magnetic field without changing the resonant Mie size parameter of the sphere by introducing an air cavity. In such a dielectric cenosphere (from two Greek words “kenos” - hollow and “sphaira” - sphere), by correct choosing of the air cavity size, it is possible to increase the intensity of the electromagnetic fields at the poles of the sphere by an order of magnitude due to increasing of amplitude of resonant partial wave coefficient.

Recent dissection studies resulted in the introduction of the term “chiasma antebrachii”, which represents an intersection of the flexor digitorum superficialis (FDS) tendons for digit 2 and 3 in the distal third of the forearm. This retrospective investigation aimed to provide an MRI-based morphologic analysis of the chiasma antebrachii. In 89 patients (41 women, 39.3±21.3 years), MRI examinations of the forearm (2010–2021) were reviewed by two radiologists, who evaluated all studies for the presence and length of the chiasma as well as its distance from the distal radioulnar and elbow joint. The chiasma antebrachii was identified in the distal third of the forearm in 88 patients (98.9%), while one intersection was located more proximally in the middle part. The chiasma had a median length of 28 mm (interquartile range: 24–35 mm). Its distances to the distal radioulnar and elbow joint were 16 mm (8–25 mm) and 215 mm (187–227 mm), respectively. T1-weighted post-contrast sequences were found to be superior to T2- or proton density-weighted sequences in 71 cases (79.8%). Concluding, the chiasma antebrachii is part of the standard FDS anatomy. Knowledge of its morphology is important, e.g. in targeted injections of therapeutics or reconstructive surgery.

The Gulong shale oil reservoir is formed in freshwater to slightly saline lacustrine basins, mainly consisting of pure shale geological structure, which is quite different from other shale reservoirs around the world. Currently, the development of Gulong shale oil mainly relies on hydraulic fracturing, while the subsequent shut-in period for imbibition has been proven to be an effective method for enhancing shale oil recovery. To clarify the characteristics of fluid occurrence space and the variation of fluid occurrence during saltwater imbibition in Gulong shale, this paper carried out porosity and permeability tests on Gulong shale cores, and analyzed the fluid occurrence space characteristics and imbibition oil recovery based on nuclear magnetic resonance (NMR). In the porosity and permeability tests, the porosity measured by saturation method was calibrated using NMR T2 spectra. Combined with the identification of fractures in shale cores using micro-CT and the analysis of porosity and permeability parameters, it was found that the permeability of shale cores was related to the development of fractures in shale cores. Through the testing and analysis of NMR T1-T2 two-dimensional spectra of the shale cores before and after saturation with oil, it was found that the shale mainly contains heavy oil, light oil, and clay-bound water, and they were distributed in different positions in the T1-T2 spectrum. Finally, the T1-T2 two-dimensional spectra of the shale core at different imbibition stages were analyzed, and it was found that the saltwater mainly entered the minuscule inorganic pores of clay minerals during the imbibition process, and squeezed the larger-sized inorganic pores containing light oil through the hydration expansion effect, thus expelling the light oil from the shale core and achieving the purpose of enhanced oil recovery.

Brain tissue segmentation is an important component of clinical diagnosis of brain diseases by means of multi-modal magnetic resonance imaging (MR). Brain tissue segmentation is developed by many unsupervised methods in literature. The most commonly used unsupervised methods are: K-Means, Expectation Maximization and Fuzzy Clustering. Fuzzy clustering methods offer considerable benefits compared with the aforementioned methods as they are capable of handling brain images which are complex, largely uncertain and imprecise in nature. However, this approach suffers from the intrinsic noise and intensity inhomogeneity (IIH) in the data resulted from the acquisition process. To resolve these issues, we propose a fuzzy consensus clustering algorithm that defines a membership function resulted from a voting schema to cluster the pixels. In particular, we first pre-process the MRI data and employ several segmentation techniques based on traditional fuzzy sets and intuitionistic sets. Then, we adopted a voting schema to fuse the results of the applied clustering methods. Finally, to evaluate the proposed method, we used the well-known performance measures (boundary measure, overlap measure and volume measure) on two publicly available datasets (OASIS and IBSR18). The experimental results show the superior performance of the proposed method in comparison with the recent state of the arts.

Simultaneously being a non-radiative and non-invasive technique makes magnetic resonance imaging (MRI) one of the highly sought imaging techniques for the early diagnosis and treatment of diseases. Despite more than four decades of research on finding a suitable imaging agent from fluorine for clinical applications, it still lingers as a challenge to get the regulatory approval compared to its hydrogen counterpart. The pertinent hurdle is the simultaneous intrinsic hydrophobicity and lipophobicity of fluorine and its derivatives that make them insoluble in any liquids, strongly limiting their application in areas such as targeted delivery. A blossoming technique to circumvent the unfavorable physicochemical characteristics of perfluorocarbon compounds (PFCs) and guarantee a high local concentration of fluorine in the desired body part is to encapsulate them in nanosystems. In this review, we will be emphasizing different types of nanocarrier systems studied to encapsulate various PFCs and fluorinated compounds, headway to be applied as a contrast agent (CA) in fluorine-19 MRI (19F MRI). We would also scrutinize the different types of PFCs and their specific applications and limitations concerning the nanoparticle (NP) system used to encapsulate them studied over the last decade. A critical evaluation for future opportunities would be speculated.

Amyloid-beta plays an important role in the pathogenesis of Alzheimer’s disease. Aberrant amyloid-beta and tau accumulation induce neuroinflammation, cerebrovascular alterations, synaptic deficits, functional deficits, and neurodegeneration, leading to cognitive impairment. Animal models recapitulating the amyloid-beta pathology such as transgenic, knock-in mouse and rat models have facilitated the understanding of disease mechanisms and development of therapeutics targeting at amyloid-beta. There is a rapid advance in high-field MR in small animals. Versatile high-field magnetic resonance imaging (MRI) sequences such as diffusion tensor imaging, arterial spin labelling, resting-state functional MRI, anatomical MRI, MR spectroscopy as well as contrast agents have been developed for the applications in animal models. These tools have enabled high-resolution in vivo structural, functional, and molecular readouts with a whole brain field-of-view. MRI have been utilized to visualize non-invasively the amyloid-beta deposits, synaptic deficits, regional brain atrophy, impairment in white matter integrity, functional connectivity, cerebrovascular and glymphatic system in animal models of amyloidosis. Many of the readouts are translational in clinical MRI in the brain of patients with Alzheimer’s disease. In this review, we summarize the recent advance of using MRI for visualizing the pathophysiology in amyloidosis animal model. We discuss the outstanding challenges in brain imaging using MRI in small animal and propose future outlook in visualizing amyloid-beta-related alterations in brain of animal models.

The liver is a key node of whole-body nutrient and fuel metabolism and is also the principal site for detoxification of xenobiotic compounds. As such, hepatic metabolite concentrations and/or turnover rates inform the status of both hepatic and systemic metabolic diseases as well as the disposition of medications. As a tool to better understand liver metabolism in these settings, in vivo magnetic resonance spectroscopy (MRS) offers a non-invasive means of monitoring hepatic metabolic activity in real time both by direct observation of concentrations and dynamics of specific metabolites as well as by observation of their enrichment by stable isotope tracers. This review summarizes the applications and advances in human liver metabolic studies by in vivo MRS over the past 35 years and discusses future directions and opportunities that will be opened by the development of ultra-high field MR systems and by hyperpolarized stable isotope tracers.

Prediction of tumor consistency is valuable for planning transsphenoidal surgery for pituitary adenoma. A prospective study was conducted involving 49 participants with pituitary adenoma to determine whether quantitative pharmacokinetic analysis of dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI) is useful for predicting consistency of adenoma. Pharmacokinetic parameters in the adenomas including volume of extravascular extracellular space (EES) per unit volume of tissue (ve), blood plasma volume per unit volume of tissue (vp), volume transfer constant between blood plasma and EES (Ktrans), and rate constant between EES and blood plasma (kep) were obtained. The pharmacokinetic parameters and the histologic percentage of collagen content (PCC) were compared between soft and hard adenomas using Mann–Whitney U test. Pearson’s correla-tion coefficient was used to correlate pharmacokinetic parameters with PCC. Hard adenomas showed significantly higher PCC (44.08 ± 15.14% vs. 6.62 ± 3.47%, p < 0.01), ve (0.332 ± 0.124% vs. 0.221 ± 0.104%, p = 0.02), and Ktrans (0.775 ± 0.401/min vs. 0.601 ± 0.612/min, p = 0.02) than soft adenomas. Moreover, a significant positive correlation was found between ve and PCC (r = 0.601, p < 0.01). The ve derived using DCE-MRI may have predictive value for consistency of pituitary adenoma.