The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

A series of ZnO doped nitrogen-carbon materials (xZnO-N-C) with ZnO content of 5-40% are prepared by vacuum curing-carbonization strategy using polyamide-imide as N-C source and zinc nitrate as metal source for propane dehydrogenation (PDH). 20ZnO-N-C exhibits outstanding initial activity (propane conversion of 35.2% and propene yield of 24.6%) and relatively low deactivation rate (0.071 h-1) at 600 ◦C. The detailed characterization results show that small ZnO nanoparticles (5.5 nm) with high dispersion on the catalyst could be obtained by adjusting ZnO loading. Moreover, much more nitrogen-based species especially ZnNx species are formed on 20ZnO-N-C by comparison with 20ZnO-N-C-air prepared by curing-carbonization without vacuum, which may contribute for the higher product selectivity and catalytic stability of 20ZnO-N-C. The probable active sites for PDH reaction on the catalyst system are proposed to be C=O species and Zn2+ species. Moreover, the aggregation of ZnO nanoparticles is the primary reason for the activity loss on this catalyst system. The present finding not only provides the feasible construction strategy for the metal oxide doped nitrogen-carbon materials but also valuable guidance for the design of efficient catalyst in dehydrogenation of light alkane.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

Keywords: Amorphous-precipitate, Nitride, Morphological stability, Diffusion, Internal stresses, Modelling, Simulation

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

Legume plants enter symbiosis with soil nitrogen-fixing bacteria (rhizobia), thereby gaining access to the assimilable atmospheric nitrogen. This symbiosis is important for agriculture, thus, biofertilizers with effective strains of rhizobia are created for crop legumes to increase their yield and minimize the amounts of mineral fertilizers used. In this work, we sequenced and characterized the genome of Rhizobium leguminosarum bv. viciae strain RCAM1022, a component of the ‘Rhizotorfin’ biofertilizer produced in Russia and used for pea (Pisum sativum L.).

The residual content of the only carbon source increases at the end of the exponential growth phase when P. putida BS3701 cells are cultured under nitrogen deficiency. Moreover, the mRNA quantity of some genes involved in carbon catabolism decreases. There are no available data on regulators capable of stimulating the target mRNA degradation in pseudomonads under nitrogen deficiency in the literature. We have applied both comparative genomics methods and a number of biomolecular ones to identify new small P. putida BS3701 RNAs. This is due to the fact that the formation of ncRNA-mRNA duplexes, recognized by RNases, is one of the main mechanisms for reducing the number of transcripts in a cell. We have used the following selection criteria: 1) the presence of the interest gene of the NtrC binding site and a sigma54-dependent promoter in the upstream area, 2) the conservative location of the interest gene in the P. putida and P. aeruginosa genomes, 3) increase in the product quantity of the interest gene in a cell under nitrogen deficiency on two different carbon sources (succinate and naphthalene), 4) the product detection of the interest gene in a fraction enriched with small RNAs. The expression of two new small RNAs has increased twice or more times under nitrogen deficiency on both succinate and naphthalene: expression of ng171 and ng379. ng379 contains narK RNA motif.

Zinc oxide is one of the most important semiconductor metal oxides and one of the most promising n-type materials, but its practical use is limited because of both its high thermal conductivity and its low electrical conductivity. Numerous studies have shown that doping with metals in ZnO structures leads to the modification of the band gap energy. In this work, Al-doped ZnO, Ni-doped ZnO, and undoped ZnO nanocrystalline powders were prepared by sol-gel method coupled with ultrasound irradiation. The doping concentration in ZnO was 1.0 at.% of Al and Ni. Influence of Al³⁺ and Ni²⁺ ions in the ZnO network are explored in this paper. X-ray Diffraction (XRD), Raman Spectroscopy, Nitrogen Adsorption (BET method), X-Ray Fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM) analyses demonstrated the incorporation of metal ions (aluminum and nickel) into the ZnO wurtzite structure. The crystallite size of the sample was decreased from 24.5 nm (ZnO) to 22.0 nm (ZnO-Al) and 21 nm (ZnO-Ni).

Plant N concentration (PNC) has been commonly used to guide farmers in assessing maize (Zea mays L.) N status and making in-season N fertilization decisions. However, PNC varies based on the development stage and therefore a relationship between biomass and N concentration is needed (i.e., critical N dilution curves; CNDC) to better understand when plants are N deficient. A few CNDC have been developed and used for plant N status diagnoses, but have not been tested in the US Midwest. The objective of this study was to evaluate under highly diverse soil and weather conditions in the US Midwest the performance of CNDCs developed in France and China for assessing maize N status. Maize N rate response trials were conducted across eight US Midwest states over three years. This analysis utilized plant and soil measurements at V9 and VT development stages and final grain yield. Results showed that the French CNDC (y=34.0x-0.37, where y is critical PNC, x is aboveground biomass) was better with a 91% N status classification accuracy compared to only 62% with the Chinese CNDC (y=36.5x-0.48). The N nutrition index (NNI), which is the quotient of the measured PNC and the calculated critical N concentration (Nc), based on the French CNDC was significantly related to soil nitrate-N content (R2=0.38-0.56). Relative grain yield on average reached a plateau at NNI values of 1.36 at V9 and 1.21 at VT, but for individual sites ranged from 0.80 to 1.41 at V9 and from 0.62 to 1.75 at VT. The NNI threshold values or ranges optimal for crop biomass production may not be optimal for grain yield production. It is concluded that the CNDC developed in France is suitable as a general diagnostic tool for assessing maize N status in US Midwest. However, the threshold values of NNI for diagnosing maize N status and guiding N applications vary significantly across the region, making it challenging for guiding specific on-farm N management. More studies are needed to determine how to effectively use CNDC to make in-season N recommendations in the US Midwest.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

Abstract Plant uptake and assimilation of essential nitrogen compounds from the soil are mainly in the form of nitrate and ammonium ions. Plant nitrate transporters (NRTs) play a crucial role in nitrate uptake from the soil into the roots. NRT structural analysis reveals the mechanisms by which these transporters function. Similarly, plant ammonium transporters (AMTs) mediate the uptake of ammonium ions, and their structural analysis has provided valuable information on their mechanisms. After nitrogen uptake by plant roots, the nitrogen metabolism pathway involves the incorporation of nitrogen into organic compounds. Glutamine synthetase (GS) and glutamate synthase (GoGAT) are the master players in this pathway. They work together to convert ammonium ions into glutamine and glutamate, respectively. Different isoforms of GS and GoGAT exist, enabling plants to fine-tune nitrogen metabolism based on environmental cues. Under severe abiotic stress conditions, nitric oxide (NO) has been found to enhance plant survival under drought. Furthermore, the interaction between salinity stress and nitrogen availability in plants has been studied, with NO identified as a potential mediator of responses to salt stress. On the other hand, excessive use of nitrate fertilizers can lead to health and environmental issues. Therefore, alternative strategies, such as establishing nitrogen fixation in plants through diazotrophic microbiota, have been explored to reduce reliance on synthetic fertilizers. Ultimately, genomics can identify new genes related to nitrogen fixation, which could be harnessed to improve plant productivity. By deciphering the genetic basis of nitrogen-fixing traits, researchers aim to develop crops that efficiently utilize nitrogen from the environment.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

In recent years, genetic research has been developing rapidly and taking on a larger role in research and medicine. The synthesis of any particle that can be used in this research can pave the way for new developments in this field. This research aims to develop a chemical method to produce nitrogen-doped carbon quantum dots - economical and bio-sourced substances that bind to genomic DNA. Carbon quantum dots are produced by the green synthesis hydrothermal method from radish, which is abundant in nature, and economically affordable. Nitrogen is added to increase the fluorescence properties of the produced carbon quantum dots and to improve their binding to DNA. The synthesized nitrogen-doped carbon quantum dots (N-CQDs) were tested through chromosome imaging subsequently. It was shown that N-CQDs can bind to the chromosomes, and N-CQDs reflected green light better than DAPI under the FITC filter, a potential advantage of using N-CQDs over DAPI in chromosome imaging.

The present study assessed the effect of abscisic acid (ABA; 25 µM) and/or nitrogen (N; 10 mM) in minimization of salinity (NaCl; 100mM)-impact on growth, photosynthetic efficiency, Rubisco activity, nitrogen and sulfur assimilation, oxidative stress (H2O2), lipid peroxidation measured as thiobarbituric acid reactive substances, (TBARS), osmolyte (Proline) content, and the activity of antioxidant enzymes (superoxide dismutase, SOD glutathione reductase, GR; ascorbate peroxidase, APX) in cultivar RH0-749 of Brassica juncea L. NaCl stress caused significant elevations in H2O2 and TBARS, and differentially modulated proline content, the activity of antioxidant enzymes, and impaired growth and photosynthetic functions. Exogenously applied 25 µM ABA negatively affected plant growth and photosynthesis in B. juncea without NaCl. In contrast, exogenously applied 25 µM ABA and 10 mM N, alone or in combination minimized oxidative stress, and maintained a fine-tuning between proline content and the activity of antioxidant enzymes, and thereby improved plant growth and photosynthetic functions in NaCl exposed B. juncea.

In order to better understand the biogeochemical cycle of nitrogen in meromictic lakes, which can serve as a model for past aquatic environments, we measured dissolved concentrations of nitrate, nitrite, ammonium and organic nitrogen in deep (39 m maximal depth) subarctic Lake Svetloe (NW Russia). The lake is a rare type of freshwater meromictic water boy with high concentrations of methane, ferrous iron, manganese and low concentrations of sulfates and sulfides in the monimolimnion. In the oligotrophic mixolimnion, the concentration of mineral forms of nitrogen decreased in summer compared to winter, likely due to phytoplankton bloom. The decomposition of the bulk of organic matter occurs under microaerophilic/anaerobic conditions of the chemocline and accompanied by the accumulation of nitrogen in the form of N-NH4 in the monimonimlion. We revealed a strong relationship between methane and nitrogen cycles in the chemocline and monimolimnion horizons. The nitrate concentrations in Lake Svetloe varied in the range from 9 to 13 μM throughout the water column. This fact is rare for meromictic lakes, where nitrate concentrations up to 13 µM are found in the monimolimnion zone down to the bottom layers. We hypothesize, in accord with available data for other stratified lakes, that under conditions of high concentrations of manganese and ammonium at the boundary of redox conditions and below, anaerobic nitrification with the formation of nitrates occurs. Overall, most of organic matter in Lake Svetloe undergoes biodegradation essentially under microaerophilic/anaerobic conditions of the chemocline and the monimolimnion. Consequently, the manifestation of the biogeochemical nitrogen cycle is expressed in these horizons in the most vivid and complex relationship with other cycles of elements.

A field experiment was conducted in Ninghe, Tianjin, China, using 15N isotope method to evaluate the application of organic fertilizer on N distribution patterns of labelled and unlabeled N fertilizer, ammonium sulfate -15N uptake by rice, N use efficiency (NUE), and the fate of (15NH4)2SO4 applied. The experiment included eight treatments: CK-N (control + no-duck), CK-D (control + ducks), CF-N (chemical fertilizer + no-ducks), CF-D (chemical fertilizer + ducks), CM-N (chemical fertilizer + organic fertilizer + no-ducks), CM-D (chemical fertilizer + organic fertilizer + ducks), CD-N (chemical fertilizer 30% off + organic fertilizer + no-ducks), and CD-D (chemical fertilizer 30% off + organic fertilizer + ducks). The results showed that the application of organic fertilizer whether CM or CD significantly increased N and P concentrations over control (CK) and chemical fertilizer (CF). Moreover, no-significant differences were found in 15N fresh grain and husk concentration. Both organs ranged of 14.2-14.4 g kg-1 and 6.2-6.3 g kg-1, respectively. N derived from the fertilizer and soil significantly affected fresh grain compared to fresh husk. However, N uptake and N use efficiency did not show any differences. We concluded that organic fertilizer has a significant influence on rice growth and promote crop productivity.

In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

Tantalum doped ZnO structures (ZnO:Ta) were synthesized and some of their characteristics were studied. ZnO material was deposited on silicon substrates by using a hot filament chemical vapor deposition (HFCVD) reactor. The raw materials were a pill made of a mixture of ZnO and Ta₂O₅ powders, and molecular hydrogen was used as a reactant gas. Percentage of tantalum was varied from 0 to 500 mg by varying the percentage of tantalum oxide in the mixture of the pill source, by holding a fixed amount of 500 mg of ZnO in all experiments. X-ray diffractograms confirmed the presence of zinc oxide in the wurtzite phase and metallic zinc with a hexagonal structure, and no other phase was detected. Displacements to lower angles of reflection peaks, compared with those from samples without contamination, were interpreted as the inclusion of the Ta atoms in the matrix of the ZnO. This fact was confirmed by EDS and XRD measurements. From SEM images from undoped samples exhibited mostly micro sized semi-spherical structures while doped samples displayed a trend to grown as nanocrystalline rods. The presence of tantalum during the synthesis affects the way of the growth. Green photoluminescence at naked eye was observed when Ta doped samples were illuminated by ultraviolet radiation and confirmed by PL spectra. PL intensity on Ta doped ZnO varied from those undoped samples up to 8 times.

We present atomic structures and nonequilbrium synthesis of new class of materials, where the basic structural unit is a diamond tetrahedron. When units of one, two, and three tetrahedra are randomly packed, we create distinct phases of amorphous Q-carbon. Four tetrahedra in two adjacent layers lead to crystalline diamond lattice, which has four missing tetrahedra alternately. When these four missing tetrahedra are filled, we create subunit cell of crystalline Q-diamond. Theoretical calculations show that superconducting transition temperature (Tc) in 50 atomic % B-doped Q-diamond can reach near room temperature at ambient pressures. This is consistent with our earlier results using low-loss EELS measurements in 50 atomic % B-doped Q-carbon, which had mostly amorphous QB3 phase mixed with some crystalline Q-diamond phase. These EELS results showed that the Tc for these samples was in between 90K and 300K. Theoretical calculations of density of states, Eliashberg function, electron-phonon interaction parameter, and root-mean-square and logarithmic average of frequency in crystalline Q-diamond show Tc in the range of 268K to 300K, which is in a complete agreement with our EELS results in QB3.

Nitrogen and phosphorous loading drives eutrophication of aquatic systems. Lakes and reservoirs are often effective N and P sinks, but information is needed on the variability of their biogeochemical dynamics, especially for tropical systems. A long-term N and P mass balance (2003-2018) in a small tropical eutrophic reservoir lake, Valle de Bravo (VB), Mexico, showed it is a net sink of N (-41.7 g N m-2 y-1), and P (-2.7 g P m-2 y-1), mainly through net sedimentation, equivalent to 181% and 68% of their respective loading (23.0 g N m-2 y-1 and 4.2 g P m-2 y-1). N mass balance showed that VB has a high net N atmospheric influx (31.6 g N m-2 y-1), which was 1.3 times the external load, and likely dominated by N2 fixation. During a period of high water level fluctuations (WLF), the net N atmospheric flux decreased by half compared to high level years. WLF can be a useful management tool to improve the trophic status of water bodies by decreasing anoxic conditions and net atmospheric fluxes, possibly through decreasing nitrogen fixation and/or promoting denitrification and other microbial processes that alleviate the N load.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Studies on N balance due to N inputs and outputs and soil N retention to measure cropping system performance and environmental sustainability are limited due to the complexity of measurements of some parameters. We measured N balance based on N inputs and outputs and soil N retention under dryland agroecosystem affected by cropping system and N fertilization from 2007 to 2011 in the northern Great Plains, USA. Cropping systems were conventional tillage barley (Hordeum vulgaris L.)-fallow (CTB-F), no-tillage barley-fallow (NTB-F), no-tillage barley-pea (Pisum sativum L.) (NTB-P), and no-tillage continuous barley (NTCB). Nitrogen rates to barley were 0, 40, 80, and 120 kg N ha-1. Total N input due to N fertilization, pea N fixation, soil N mineralization, atmospheric N deposition, nonsymbiotic N fixation, and crop seed N and total N output due to grain N removal, denitrification, volatilization, N leaching, gaseous N (NOx) emissions, surface runoff, and plant senescence were 28 to 37% greater with NTB-P and NTCB than CTB-F and NTB-F. Total N input and output also increased with increased N rate. Nitrogen sequestration rate at 0 to 10 cm averaged 22 kg N ha-1 yr-1 for all treatments. Nitrogen deficit ranged from 5 to 16 kg N ha-1 yr-1, with greater deficits for CTB-F and NTB-P and higher N rates. Because of increased grain N removal and reduced N loss to the environment and N fertilizer requirement, NTB-P with 40 kg N ha-1 can enhance agronomic performance and environmental sustainability while reducing N inputs compared to other management practices.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Nitrogen (N) applications can play a key role in achieving profitable wheat production in the low-fertility soils prevalent under rainfed conditions. The model-predicted N partitioning revealed that ammonia-nitrogen (NH4-N) contributed little to the plant N nutrition, and its concentration in the soil remained below 2 ppm throughout the crop season except immediately after the NH4-N based fertilizer application. Nitrate-nitrogen (NO3-N) gradually increased (maximum 144 ppm) with time, especially in the 0-40 cm horizons, and contributed to most N uptake during both seasons at both locations. The N losses from the soil at the medium rainfall site (3.5-20.5 kg ha-1) were mainly attributed to NH4-N volatilization (Nv) and NO3-N leaching (NL) below the crop root zone. Water productivity (8-40 kg ha-1 mm-1) and N use efficiency (31-41 kg kg-1) showed immense variability induced by climate, water availability, and N dynamics in the soil. These results suggest that combining water balance and N modeling can help manage N applications to optimize wheat production and minimize N losses in rainfed agriculture.

Information on how bacteria in plants and soil, along with extracellular enzymes, affect nutrient cycling in Encephalartos villosus growing in nutrient-poor and acidic scarp forests is lacking. Bacteria in coralloid roots, rhizosphere, and non-rhizosphere soils were isolated to determine the potential role of soil bacterial communities and their associated enzyme activities in nutrient contributions in rhizosphere and non-rhizosphere soils. The role of soil characteristics and associated bacteria on E. villosus nutrition and nitrogen source reliance was investigated. Encephalartos villosus leaves, coralloid roots, rhizosphere, and non-rhizosphere soils were collected at two scarp forests. Leaf nutrition, nitrogen source reliance, soil nutrition and extracellular enzyme activities were assayed. A phylogenetic approach was used to determine the evolutionary relationship between identified bacterial nucleotide sequences. Twenty, twelve and seven different bacterial genera were isolated from rhizosphere, non-rhizosphere, and coralloid roots, respectively. Phosphorus and nitrogen cycling enzyme activities in E. villosus rhizosphere and non-rhizosphere soils were insignificant. More than 70% of the leaf nitrogen was derived from the atmosphere. This study revealed that plant-associated bacteria with plant growth-promoting functions, soil bacteria, and associated extracellular enzymes play a role in E. villosus nutrition and nitrogen source reliance and contribute to E. villosus rhizosphere and non-rhizosphere soil nutrition.

Nitrogen (N) is an essential nutrient and plays an important role in plant growth and physiology. In addition, N is also the limiting nutrient in most terrestrial ecosystems. The increasing use of N fertilizers increases agricultural production, but also has negative impacts on biodiversity, water quality and increases emissions of greenhouse gases such as nitrogen oxides (NOx) and nitrous oxide (N2O) into the atmosphere. N2O is a strong greenhouse gas and the product of microbial transformation processes of N introduced into soil and groundwater (nitrification and denitrification). The production of N2O in soils is highly dependent on oxygen and water content, soil temperature and texture and the available amount of reactive nitrogen (NO3- or NH4+). In agricultural soils, N2O emissions are also influenced by the type of fertilizer used, crops grown, soil pH and NO3- concentration. Refined forms of land management, such as the cultivation of legumes, can reduce the use of fertilizers and thus also the emission of N2O. Legumes can use symbiotic nodule bacteria (rhizobia) to bind atmospheric N2 and make it available to the plant. Non-symbiotic soil microorganisms such as cyanobacteria or other heterotrophic and autotrophic prokaryotes are also able to fix N2. Furthermore, the N2-fixing enzyme nitrogenase, which is specific for most organisms, is not specific for other N2 compounds, especially N2O. To study the N2 and N2O fixation potential of soils and legumes, experiments with isotope-enriched N-gases (100 mol% 15N2 and 15N2O) were performed. Three different soil types (forest, meadow and wetland) as well as legume plants inoculated with rhizobia bacteria (Rhizobium leucaneae) (Leucaena leucocephala) were incubated in microcosms with different mixing ratios of N2 and N2O over a period of one week. The measured 15N enrichment was then used to determine the biological uptake rates. Both in plants and in soils admixtures of up to 40% N2O had no influence on the N2 fixation rate. N2 uptake rates were 1.2 ± 0.4 ug N gdw-1 d- 1in forest and grassland soils and 3.9 ± 1.2 ug N gdw-1 d- 1 in wetland soils. In contrast, the N2 fixation rates of leguminous plants were significantly higher (130 ± 40 ug N gdw-1 d- 1), with the highest accumulation not in root nodules but in the roots. In both plants and soil, the N2O fixation of 0.2 ± 0.1 ug N gdw-1 d- 1 could only be measured from a concentration of 4 vol%. The results indicate that both soils and legumes have a high potential to bind atmospheric nitrogen in the form of both N2 but not N2O. The fate of nitrogen in soil needs to be further investigated. N2 fixation seems to play an important role in wetland soils. Legumes in particular have the potential for NH4+ input and N2O reduction, as most of the solid nitrogen has been transferred to the roots, which can contribute significantly to soil nutrient input.

The objective of the present study was to develop and optimize an efficient growth media for Lactobacillus delbrueckii ssp. bulgaricus, an essential dairy starter culture, uses plant-based nitrogen sources. The composition of the de Man, Rogosa, and Sharpe (MRS) culture medium was modified, and the nitrogen content was replaced by alternative nitrogen sources X-Seed N7 and N5 in various blends of 3% and 1.5%. Results showed that bacterial growth was higher with the N7 and N5 nitrogen source blends at 3% and 1.5%. Similarly, the optical densities of the L. bulgaricus strains were higher in the N7 and N5 blends (1.5/3%) compared to the MRS medium. Although there was no significance in bacterial counts for both the MRS and the N7 and N5 media, a significant difference between the control medium and the optimized growth media was noted. Our results thus suggest that the alternative nitrogen sources X-Seed N7 and N5 can substantially support the growth of lactic acid bacteria as shown with L. bulgaricus. Moreover, the presence of complex nitrogen sources rich in free nucleotides, amino acids, and peptides enhanced L. bulgaricus growth. Our results support the development of cost-effective and plant-based growth media for LAB cultures and potential benefits to the food and dairy industries. Additional research is warranted to improve buffering capacity for higher cell counts.

In the present study, the potential of ethylene as ethephon (an ethylene source) was investigated individually or with a combination of the split dosage of nitrogen (N) and sulfur (S) soil treatments for the removal of damaging effects of salt stress (100 mM NaCl) in mustard (Brassica juncea L.). Plants were grown with 50 mg N plus 50 mg S kg−1 soil at sowing time and an equivalent dosage at 20 days after sowing ([N50 + S50]0d + [N50 + S50]20d). Ethephon at 200 μL L‒1 was applied to combined split dosage of N and S with or without NaCl. Plants subjected to NaCl showed a deceased in growth and photosynthetic characteristics as well as N and S assimilation, though, proline metabolism and antioxidants increased. The application of ethephon to plants grown with split N and S dosages significantly enhanced the photosynthetic efficiency by increasing the assimilation of N and S, improving the content of proline and induction of the antioxidant system with or without NaCl. The regulation of ethylene and/or split form N and S application may be the potential tools for overcoming salt stress effects in this species and in related Brassicaceae.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

In this paper we propose a simple procedure to obtain multi-walled carbon nanotubes (MWCNT) decorated with TiO₂-Ag nanoparticles (MWCNT-TiO₂-Ag). MWCNT were decorated with TiO2-Ag via combined functionalisation with -OH and –COOH groups and polymer wrapping technique using poly(allylamine hydrochloride) (PAH). TiO₂ modified Ag nanoparticles were synthesized through Pechini method using mixture of acetylacetonate-modified titanium (IV) isopropoxide with silver nitrate (the Ag+/Ti4+ atomic ratio, is 0.5, 1,0, 1.5, 2.0 and 2.5 %, respectively) and the L(+)-ascorbic acid, as reducing agents. XRD analysis revealed the formation of nanocomposite containing CNT, TiO₂ (anatase and rutile) and Ag. By SEM was evidenced the presence of the nanoparticles on MWCNT surface. The increases of the ratio between Ag⁺ and Ti⁴⁺ decrease the band gap energy of the samples. In Raman spectra the characteristic vibration of the TiO₂, Ag and C atoms of graphite are identified. The photocatalytic activity of the MWCNT-TiO₂-Ag nanocomposite was assessed by examining the degradation of Allura red (E129) aqueous solution under UV irradiation. The dye photodegradation process follows a pseudo – first – order kinetic with respect to the Langmuir – Hinshelwood reaction mechanism.

Maize (Zea mays L.) is the most widely grown important crop in mid altitude areas of intensive maize-based cropping system of western Ethiopia. Agronomic management is the most important input for getting potential yield and high net returns in hybrid maize production. A field experiment was carried out on farmers’ field to find out the effect of varieties (four maize) and nitrogen fertilizer rate (55, 110 kg N ha-1) with one control on yield components and nitrogen use efficiency of different maize varieties in 2013 and 2014 cropping season. It was laid with randomized complete block design in factorial arrangement with three replications. Mean grain yield, thousand seed weight, dry biomass and harvest index of maize varieties were significantly differed among farms and varieties of maize. Application of nitrogen fertilizer rates was significantly increased mean grain yield maize varieties. Interaction of maize varieties with nitrogen fertilizer rates was significantly affected all yield components of maize varieties. Application half and full recommended nitrogen fertilizer gave mean grain yield advantages of 31 and 41 % over control maize varieties planted without nitrogen application. Maize varieties producing higher mean grain yield was also giving higher mean dry biomass. Mean nitrogen up take was varied from 225 to 357 kg ha-1 among varieties of maize. Higher agronomic efficiency of all maize varieties was obtained from maize planted with application half recommended nitrogen fertilizer compared to full recommend. Agronomic efficiency was ranged from 18 to 33 produced among maize varieties. Significantly higher nitrogen up take efficiency of maize varieties was achieved from maize planted with full recommended nitrogen fertilizer application. Considerably higher nitrogen use efficiency of maize varieties was realized from all maize varieties planted with application half recommended nitrogen fertilizer. Application of half recommended nitrogen fertilizer was gave 32 % fertilizer N use efficiency advantage as compared to full recommended nitrogen fertilizer. Maize varieties BH-661>BH-660> BH-543>BH-540>BH-140 were desirable varieties for further promotion work and use by smallholder farmers in mid altitude area of western Ethiopia.

Nitrogen (N) is the most limiting nutrient for the production of vegetable crops, but anthropogenic sources pose risks due to its transformation into several reactive forms and movement throughout the environment. To mitigate the impact of environmental losses, current research efforts aim to improve management practices to obtain a greater Nutrient Use Efficiency (NUE). From a chemical, biological, and ecophysiological perspective, at a reductionist level we have acquired a considerable mechanistic understanding about the N cycle, the varied N chemical forms, microbial interactions and physiology of crop uptake. However, at a holistic level, we are far from obtaining an adequate understanding of the myriad of multi-level cropping system, genetic, socioeconomic, environmental, and ecological interactions that have an effect on the N cycle and NUE. Here, based on a selected review of the literature, we provide a perspective on the potentials to increase the NUE of vegetable crops, by adopting a range of best management practices and by highlighting some of the N x system interactions that may be considered to better understand the complex dynamics of the N cycle, to optimize the NUE of vegetable crops, and to explore alternatives to the reliance on the use of synthetic N sources.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

To realize high response and selectivity gas sensor in detecting dissolved gases in transformer oil, in this study, the adsorption of four kinds of gases (H2, CO, C2H2 and CH4) on Pd-graphyne as well as the gas sensing properties evaluation were investigated. The energetically favorable structure of Pd doped γ-Graphyne was first studied, including the comparison of different adsorption sites and discussion of electronic properties. Then, the adsorption of these four molecules on Pd-graphyne was explored. The adsorption structure, adsorption energy, electron transfer and electron distribution, the band structure and density of states were calculated and analyzed. The results show that the Pd atom prefers to be adsorbed on the middle of three C≡C bonds and the band gap is smaller. The CO adsorption exhibits the largest adsorption energy and electron transfer and brings obvious change to the structure and electron properties to Pd-graphyne. Because of the conductance decrease after adsorption CO and acceptable recovery time at high temperature, the Pd-graphyne can be promising gas sensing materials to detect CO with high selectivity. This work offers theoretical support for the design of nanomaterials based gas sensor using novel structure for industrial application.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Conventional flame retardant (FR) application processes for textiles involve aqueous processing which is resource intensive in terms of energy and water usage. Recent research using sol-gel and layer-by-layer chemistries, while claimed to be based on more environmentally-sustainable chemistry, still require aqueous media with the continuing problem of water management and drying processes being required. This paper outlines the initial forensic work to characterise commercially produced viscose/flax, cellulosic furnishing fabrics which have had conferred upon them durable flame retardant (FR) treatments using a novel, patented atmospheric plasma/UV excimer laser facility for processing textiles with the formal name - Multiplexed Laser Surface Enhancement (MLSE) system. This system (MTIX Ltd., UK), is claimed to offer the means of directly bonding of flame retardant precursor species to the component fibres introduced either before plasma/UV exposure or into the plasma/UV reaction zone itself, thereby eliminating a number of wet processing cycles. Nine commercial fabrics, pre-impregnated with a semi-durable, proprietary FR finish and subjected to the MLSE process have been analysed for their flame retardant properties before and after a 40 °C 30 min water soak. For one fabric, the pre-impregnated fabric was subjected to a normal heat cure treatment which conferred the same level of durability as the plasma/UV-treated analogue. TGA and LOI were used to further characterise their burning behaviour and the effect of the treatment on surface fibre morphologies were assessed. Scanning electron microscopy indicated that negligible changes had occurred to surface topography of the viscose fibres occurred during plasma/UV excimer processing.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

Dryland winter wheat in Loess Plateau is facing yield reduction due to shortage of soil moisture and delayed sowing time. Field experiment was conducted at Loess Plateau in Shanxi Province, China from 2012 to 2014, to study the effect of subsoiling and conventional tillage and different sowing dates on the soil water storage and contribution of N accumulation and remobilization to yield of winter wheat. The results showed that subsoiling significantly improved the soil water storage at 0-300 cm depth, improved the number of tillers and pre-anthesis N translocation in various organs of wheat and post-anthesis N accumulation, eventually increased the yield up to 17-36%. Delaying sowing time had reduced the soil water storage at sowing and winter accumulated temperature by about 180˚C. The contribution of N translocation to grain yield was maximum in glume+spike followed by in leaves and minimum by stem+sheath. In addition a close relationship was found between the N accumulation and translocation and the soil moisture in the 20-300 cm. Subsoiling during the fallow period and the medium sowing date was beneficial for improving the soil water storage and increased the N translocation to grain, thereby increasing the yield of wheat, especially in dry year.

The objective of this work was to investigate the effect of different soil tillage practices in sunflower cultivation in a rotation system with intercropping Triticosecale x Pisum sativum. For this purpose a two year experimental field of 5% slope was established in central Greece. There were four treatments with three replications each. The treatments were: (a) no tillage - planting parallel to the contour (NTC-PAC), (b) conventional tillage - planting parallel to the contour (CTC-PAC), (c) no tillage - planting perpendicular to the contour (NTC-PEC), (d) conventional tillage - planting perpendicular to the contour (CTC-PEC). During the experiment plant height, leaf area index, specific leaf area, plants’ total nitrogen and plants’ proteins were measured. According to the results plant height ranged from 64.9 (CTC-PAC) to 85.2 cm (NTC-PEC) the 1st year and between 66.5 – 86.5 cm in CTC-PAC and NTC-PEC treatments in the 2nd year. Furthermore, LAI and SLA, plant’s total nitrogen and protein content and N-uptake were affected positively by the no tillage practice. To conclude, sunflower is a promising crop in a rotation system with intercropping Triticosecale x Pisum sativum, cultivating under rainfed sloping conditions.

Over the years, scarcity of fresh potable water has increased the demand for clean water. Meanwhile, with the advent of nanotechnology, the use of nanomaterials for photocatalytic degradation of pollutants in wastewaters has increased. Herein, a new type of nanohybrids of La and Mn co-doped bismuth ferrite (BiFeO₃) nanoparticles embedded into transition metal carbide sheets (MXene) were prepared by a low-cost double solvent sol-gel method, and investigated for their photocatalytic activity. The photoluminescence results showed that pure BFO has highest electron hole recombination rate as compared to all the co-doped BFO/MXene nanohybrids. The larger surface area and higher electron-hole pair generation rate provides suitable environment for fast photo-degradation of organic molecules. The band gap of the prepared nanohybrids was tuned to 1.96 eV having largest BiFeO₃ surface area (147 m²g⁻¹) reported till date. Moreover, the BLFO/MXene and BLFMO-5/Mxene degraded the 92% organic pollutant from water in dark and remaining in light spectrum as compare to undoped BFO/Mxene due to enhancement of the surface area and electron-hole recombination rate upon doping. Therefore, these synthesized nanohybrids could be a promising candidate for photocatalytic applications in future.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

The dynamics of hydrological lateral nutrient fluxes contribute to our understanding of ecological functions related to energy, materials, and organism flows across various spatiotemporal scales. To explore the connectivity between multiple spatial flow processes, we conducted a one-year field measurement to assess lateral hydrologic carbon (C) and nitrogen (N) fluxes over the continental shelf in the Yangtze estuary. We observed a significant correlation between the differences in remote sensing-based estimates of gross primary production (GPP) (∆GPPMODIS) and the differences in eddy covariance (EC) tower-based GPP (∆GPPEC) at both high-elevation and low-elevation sites. Over the course of a year, our predicted daily maximum tidal elevation (TE) closely matched the observed values in the creek, which facilitated the development of theoretical models to simulate biogeochemical cycling processes and aquatic ecosystem functions. Our findings indicate that the studied saltmarsh acts as a net exporter of dissolved total C (DTC) while serving as a net sink for dissolved total N (DTN). Furthermore, there is a significant correlation in the total dissolved stoichiometry of the C/N ratio between imports and exports. These findings highlight the importance of integrating ecological stoichiometric principles to gain a deeper understanding of the complex relationships between physical, chemical, and biological processes, particularly within the context of the meta-ecosystem framework. Additionally, when considering reciprocal hydrological lateral C and N flows, single ecosystem can function both as sources and sinks within the meta-ecosystem framework.

Inherent low soil fertility status limits productivity of rice in the lowland ecologies in Northern Ghana. Combining organic and inorganic N fertilizers could help to maintain the fertility of lowland soils for rice production. A screen house pot experiment was carried out to investigate the combined effect of biochar-compost and inorganic N fertilizer on the nitrogen uptake and agronomic performance of rice plants grown on Eutric Gleysol lowland soil. Inorganic N fertilizer alone and its combinations with different types of biochar-compost (based on the proportions of biochar and compost) were used as treatment. A control (unamended soil) was also included. The incorporation of biochar-compost and inorganic N fertilizer improved the growth parameters and yield components of rice plants. The combination of biochar-compost and inorganic nitrogen fertilizer was also found to improve nitrogen uptake and nutrient use efficiency (NUE) in rice plants. This practice could be the most likely viable option for alleviating lowlands soil fertility issues and increasing rice productivity in Northern Ghana.

Abstract: Marine eutrophication is a pervasive and growing threat to global sustainability. Thereby nutrient discharges to the marine environment should be reduced to a minimum. When fertilizers are loaded to vessels in ports, a significant amount of nutrients are released into the sea, but so far these actions have received little attention. Here, we employed the Boosted Regression Trees modeling (BRT) to define relationships between fertilizer loading, loading area, rain intensity and nutrient discharge to the marine environment and then used the established relationships to predict daily nutrient discharge due to fertilizer loading. The studied subject was a port in the Gulf of Finland, where significant amount of both nitrogen and phosphorus are loaded to vessels. BRT models accounted for a significant proportion of the variability of nutrient discharge. As expected, the nutrient discharge increased with the amounts of fertilizers loaded and the intensity of rain. On the other hand, with increasing loading area the amounts of total nitrogen discharge increased, but phosphorus discharge decreased. The latter result may be due to different char-acteristics of the loading areas of different terminals. The model predicted that at the studied port the total nitrogen and phosphorus discharge into the marine environment due to fertilizer loading was 272,906 and 196 kg per year, respectively. Im-portantly, the developed model can be used to predict nutrient loads for different future scenarios to propose the best mitigation methods for nutrient discharges to the sea.

We present an innovative method harnessing multistability within a diode-pumped erbium-doped fiber laser to construct logic gates. Our approach involves manipulating the intensity of external noise to regulate the probability of transitioning among four concurrent attractors. In this manner, we facilitate the realization of OR, AND, NOT, and NOR logic operations, aligning with the coexisting period-1, period-3, period-4, and period-5 orbits. Employing detrended fluctuation analysis, we establish equilibrium in the probability distributions of these states. The obtained results denote a substantial advancement in the field of optical logic gate development, representing a pivotal stride toward the seamless integration of an all-optical logic gate within laser oscillator-based systems.

In this work, oxygen-doped g-C3N4 mesoporous nanosheets (O-CNS) were synthesized via a facile recrystallization method with the assistance of H2O2. The crystal phase, chemical composition, morphological structure, optical property, electronic structure and electrochemical property of the prepared O-CNS samples were well investigated. The morphological observation combining with nitrogen adsorption-desorption results demonstrated that the prepared O-CNS samples possessed nanosheets-like morphology with porous structure. The O doping into g-C3N4 resulted in the augment of specific surface area, which could provide more active sites for photocatalytic reaction. Simultaneously, the visible-light absorption capacity of O-CNS samples was boosted owing to the regulation of O doping. The built energy level induced by the O doping could accelerate the migration rate of photoinduced carriers, and the porous structure was most likely to speed up the release of hydrogen during photocatalyic hydrogen process. Resultantly, the photocatalytic hydrogen production rate of the optimized oxygen-doped g-C3N4 nanosheets reached up to 2012.9 μmol•h-1•g-1, which was 13.4 times higher than that of bulk g-C3N4. Thus, the significantly improved photocatalytic behavior was imputed to the porous structure, the augment of active sites, and the enhancement of visible light absorption and charge separation efficiency.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Graphene-based nanomaterials have emerged as promising materials for a wide range of applications.. Therefore, in the last years carbon nanoparticles have attracted great attention due to their low toxicity, high biocompatibility and easy preparation. Recently, N-doped carbon nanoparticles have been shown to have improved antibacterial activity over the undoped nanomaterial, but it is difficult to find correlations between the structure of the nanoparticle and its antibacterial activity. With this purpose, here, we analyze the effect of both, the nanoparticle size and the surface chemical composition of four N-doped carbon nanoparticles on the growth of Escherichia coli bacteria. Our results were analyzed using a Ligand-Substrate model based on the Monod´s equation, which allows us to interpret the dependence of the nanoparticle-bacteria affinity with the nanomaterial structure.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

Carboxylic acids such as acetic acid and propionic acid have been investigated as representative components for fast pyrolysis (FP) bio-oil upgrading. Selective catalytic conversion of carboxylic acids can enhance bio-refinery processing economics through catalyst preservation and process intensification. Various metal-doped molybdenum carbide bead catalysts have been synthesized and developed in this work. Our aim is to enable selective conversion of carboxylic acids. In the case of acetic acid conversion, calcium doped Mo₂C beads offer the highest yield of acetone ~96% at 450 °C among undoped and Ca or Ni doped catalysts. By comparing hot gas filter with and without Ca-Mo₂C catalyst tested with real FP vapors, the former showed a 36.7% reduction of acetic acid, a 37.5% reduction of small ketones in aqueous phase, and a ~50% reduction of methoxies (methoxy phenols and methoxy aromatics) in organic phase. The conversion resulted in the formation of more long chain chemicals in the organic phase, which are more amendable for downstream upgrading.

A series of Eu³⁺ doped CaSiO₃/SiO₂ nano-phosphor powder of controlled grain size, crystalline structure, and chemical composition were synthesized using the microemulsion technique. XRD profiles of samples sintered over 600 of suggested phase shift from amorphous powder grain to more ordered polycrystalline powder of triclinic type wollastonite, CaSiO₃, with preferred crystal phase orientation of (112) and tetragonal type cristobalites of SiO₂. The grain size, crystallinity, and chemical composition of the host matrix, activator and sensitizer strongly affected both the absorption and emission bands of these samples. The amplitude of both the orange and red emission bands significantly increased with sintering temperature. The emission band is red-shifted with decreasing grain sizes. These bands displayed good sensitivity to ionic concentration of the Si⁴⁺, Ca²⁺, and Eu³⁺. With increasing Ca²⁺ ion concentration both the intensity of the red photoluminescence (PL) band increased and a concentration quenching observed. Increase in Si⁴⁺ ion concentration led to quenching in PL intensity of both the orange and red bands whereas the amplitude of the blue-band slightly increased. With increasing Eu³⁺ ion concentration the red-band initially increased whereas it started decreasing at higher sample concentration. In the presence of Ca²⁺ ion as a sensitizer, the sample showed a remarkable PL property—including—about 100% photon conversion efficiency and a two-fold increase in excitation and emission photons.

Switchgrass (Panicum virgatum L.) remains the preeminent American perennial (C4) bioenergy crop for cellulosic ethanol that could help displace over a quarter of the US current petroleum consumption. Intriguingly, there is often little response to nitrogen fertilizer once stands are established. The rhizosphere microbiome plays a critical role in nitrogen cycling and overall plant nutrient uptake. We used high-throughput metagenomic sequencing to characterize the switchgrass rhizosphere microbial community (5.37 billion Illumina reads at 805 Gbp of data) before and after a nitrogen fertilization event for established stands on marginal land. We examined community structure, bulk metabolic potential, and resolved 29 individual bacteria genomes via metagenomic de novo assembly. Community structure and diversity were not significantly different before and after fertilization; however, the bulk metabolic potential of carbohydrate-active enzymes was depleted after fertilization. We resolved 29 metagenomic assembled genomes including some from the ‘most wanted’ soil taxa such as Verrucomicrobia, Candidate phyla UBA10199, Acidobacteria (rare subgroup 23), Dormibacterota, and the very rare Candidatus Eisenbacteria. The Dormibacterota (formally candidate division AD3) we identified have the potential for autotrophic CO utilization, which may impact carbon partitioning and storage. Our study also suggests that the rhizosphere microbiome may be involved in providing associative nitrogen fixation (ANF) via the novel diazotroph Janthinobacterium, which may partially explain why switchgrass growth is insensitive to fertilizer.

The effects of exogenous inorganic [i.e., nitrate (NO3-)/ammonium (NH4+)] and organic [i.e., glutamate (Glu)/argine (Arg)] N alone and in combination on the accumulation of proline (Pro) in rice plant under trivalent chromium [Cr(III)] stress were studied through the mass balance matrix model (MBMM). ‘NH4+’ application showed the largest contribution to the Pro content in rice shoots under different concentrations of Cr(III), followed by ‘NO3-’, ‘Arg’, and ‘Glu’ application respectively. While, ‘Arg’ application displayed the largest contribution to the Pro content in roots under Cr(III) stress, followed by ‘NH4+’, ‘Glu’, and ‘NO3-’ application. Among the combination cases of N sources used, the application of ‘NH4++Arg’ showed the greatest contribution to the Pro content in both roots and shoots of Cr(III)-treated rice seedlings, while the application of ‘NO3-+Glu’ showed the least contribution to the Pro content in rice seedlings under Cr(III) stress. Results from this study indicated that the level of indigenous Pro in rice seedlings is quite sensitive to Cr(III) stress under different N sources, and mathematical modeling showed a reliable result to estimate the relationship between Pro content and N source application in rice plants in response to Cr(III) exposure .

Soil enzyme activity can be affected by both production and degradation, as enzymes can be degraded by proteases. However, the impact of nutrient addition on enzyme activity is often solely attributed to changes in enzyme production without fully considering degradation. Here, we demonstrated that the activities of β-1,4-glucosidase (BG), β-D-cellobiohydrolase (CBH), β-1,4-Xylosidase (BX), and β-1,4-N-acetyl-glucosaminnidase (NAG) were comparable in nitrogen (N) and phosphorus (P) fertilized soils and the unfertilized control under field conditions, but the reduction in activity was substantially greater in the fertilized soils during short-term laboratory incubation. The results show that the interruption of the natural, continuous supply of organic matter or non-soil microbial-derived enzymes, which typically occurs under field conditions, leads to a more significant reduction in apparent enzyme activities in fertilized soils compared to unfertilized control. This may be attributed to the higher abundance of protease in fertilized soils, resulting in faster enzyme degradation. Interestingly, P fertilization alone did not have a similar effect, indicating that N fertilization is likely the main cause of the larger decreases in enzyme activity during incubation in fertilized soils compared to unfertilized control soils, despite our study site being poor in P and rich in N. These findings highlight the importance of considering enzyme degradation when investigating material dynamics in forest ecosystems, including the impact of nutrient addition on enzyme activity, as enzyme production alone may not fully explain changes in apparent enzyme activity.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

CONTEXT: The sustained White corn (Zea mays L.) yield relies on supply of Nitrogen (N), which is an important element in improving soil fertility. OBJECTIVE: The research aim to determine the effect of Nitrogen on white corn yield and grain mass. METHOD: The experimental design was a 4 × 4 factorial arranged in randomized complete block design with 2 replications each. The effect of nitrogen was determined in terms of the flow within the soil, initial component, addition, uptake, loss and use of nitrogen by the White corn plants. Nitrogen was applied as Granular Urea using zero broadcast method. The grain yield was determined hand-harvesting and shelling. RESULTS AND CONCLUSIONS: There were no statistically significant differences between the mean samples from the two replicates (blocks 1 & 2) across the two seasons for corn sugar concentration, corn yield estimates and grain yields. In 2021, the mean yield estimate was 12,552 Kg ha-1, while that of 2022 averaged 12687 Kg ha-1. Similarly, the grain yield achieved in 2022 was 844.1kg more than the average grain yield in 2021. The white corn yield estimate and grain yield increased linearly with an increase in nitrogen application level, with the highest yields achieved when nitrogen fertilizer was applied at 150kg N/ha. This demonstrates that nitrogen has a positive influence on the yield quantity of white corn. SIGNIFICANCE: The White maize model may be used to improve the formulation of decisions and enhance the precision of estimates for yield and N fate within the soil-plant-atmosphere continuum. Further, the findings of this study can significantly enhance agricultural productivity while keeping an eye on the environment.

Rice production is a significant contributor to methane emissions, accounting for ap-proximately 11% of global anthropogenic emissions. However, methane emissions in rice fields could effectively be reduced by implementing proper management practices and careful cultivar selection. The impact of nitrogen fertilizers on methane emissions is mul-tifaceted, as these fertilizers enhance crop growth and influence the activity of me-thane-producing (methanogens) and methane-consuming microbes (methanotrophs), leading to complex outcomes in methane emissions. In this study, we used qPCR to quan-tify methanogens and methanotrophs using mcrA (methanogenesis-related gene) and pmoA (methane oxidation-related gene) primer sets under different nitrogen levels (0, 50, and 100%) and rice varieties. The results revealed that higher nitrogen input led to higher methanogen inhabitation in the rhizosphere. Additionally, the abundances of methano-gens and methanotrophs varied among the different rice varieties. Furthermore, it was observed that there may be an additive effect between the rice variety and nitrogen level used. These findings suggest that future breeding efforts should involve screening for me-thane-related microbes in rice cultivars adapted to low-nitrogen conditions. By identifying and selecting rice varieties that promote lower methanogen levels and higher metha-notroph inhabitation, significant steps can be taken to mitigate greenhouse gas emissions from rice cultivation.

Abstract: Rice production is a significant contributor to methane emissions, accounting for approximately 11% of global anthropogenic emissions. However, there is potential for effectively reducing methane emissions from rice fields through the implementation of proper management practices and careful cultivar selection. The impact of nitrogen (N) fertilizers on methane (CH4) emissions is multifaceted, as these fertilizers not only en-hance crop growth but also influence the activity of methane-producing microbes (Meth-anogens) and methane-consuming microbes (Methanotrophs), leading to complex out-comes in CH4 emissions. In this study, we utilized qPCR to quantify methanogens and methanotrophs using mcrA (methanogenesis-related gene) and pmoA (methane oxida-tion-related gene) primer sets under different nitrogen levels (0, 50, 100%) and rice varie-ties. The results revealed that higher nitrogen inputs led to higher methanogen inhabita-tion in the rhizosphere. Additionally, the abundances of methanogens and metha-notrophs varied among different rice varieties. Furthermore, through the analysis of two-way ANOVA, it was observed that there may be an additive effect between rice variety and nitrogen level. Furthermore, enhancing agronomic traits related to yield can reduce methanogen inhabitation. These findings suggest that future breeding efforts should in-volve the screening of methane-related microbes in rice cultivars adapted to low nitrogen conditions. By identifying and selecting rice varieties that promote lower methanogen lev-els and higher methanotroph inhabitation, we can take significant steps towards mitigating greenhouse gas emissions from rice cultivation.

Cuboid diamonds are particularly common in the placers of the northeastern Siberian platform but their origin remains unclear. These crystals usually range in color from dark yellow to orange and more interestingly, are characterized by unusual low aggregated nitrogen impurities (non-aggregated C-center) suggesting a short residence time and/or low temperatures at which they have been stored in the mantle. In order to track possible isotopic signature that could help deciphering cuboid diamond's crystallization processes, δ¹³C values, δ¹⁵N values and nitrogen contents have been determined in-situ in three samples using secondary ion mass spectrometry (SIMS), whereas nitrogen aggregation state have been determined by FTIR spectroscopy. The samples fall out the δ¹³C vs. δ¹⁵N field of canonical mantle composition. Different scale of carbon and nitrogen fractionation may produce the observed variations. Alternatively, mixing of mantle and crustal material would obscure initial co-variations of δ¹³C values with δ¹⁵N or nitrogen content.

To increase rice production, fertilizer plays a crucial role in rice yield. In this research, we applied the coupled atmospheric and crop model, which is based on the WRF and CERES-Rice models, to find the appropriate nitrogen fertilizer level for increasing rice yield production in northern Thailand. The model was conducted from October to December in 2011 to 2015. To evaluate the model capability, the output from the model, including meteorological data, i.e., precipitation and temperature, and rice production, as compared to actual observation data. The modeling system shows an acceptable level of output for statistical examination; for example, the R² values were 0.93, 0.76, and 0.97 for precipitation, temperature, and rice production, respectively. To assess the optimization of the nitrogen fertilizer level, we designed 9 experiments: control cases and other cases that were multiplied by a factor of 2 – 10 times the nitrogen fertilizer levels. The model suggested that we can produce worthwhile rice yield production by approximately 4830 kg/ha if we increase the nitrogen fertilizer levels by 36 kg/ha.

A two-year field experiment (2022–2023) was carried out to investigate the impact of different sowing periods (spring and winter) and nitrogen levels (0, 30, 60 kg/ha) on the phytoextraction potential of flax. The study site is characterized by high concentrations of heavy metals (Cd, Ni, Cu, Pb, Zn) and belongs to the Mediterranean climate type. Flax (var. Calista) was sown in the spring of 2022 and in the winter of 2023, following a split plot experimental design with three rep-lications, and applying low-input practices. Results showed that spring-sown flax produced short-er but thicker plants with significantly higher biomass (5.27 tn ha-1) when treated with 30 kg ha-1 N compared to winter-sown (2.30 tn ha-1) when treated with 60 kg ha-1 N. The concentration of contaminants in the aerial biomass varied according to metal type and sowing period. The higher biomass production in spring resulted in a higher quantity of heavy metals being removed from the soil, making flax a promising crop for phytoextraction purposes, especially in soils contami-nated with multiple heavy metals.

The root-colonizing endophytic fungus Piriformospora indica promotes root and shoot growth of its host plants. We show that growth promotion of Arabidopsis leaves is abolished when the seedlings are grown on media with nitrogen (N) limitation. The fungus neither stimulated the total N content nor did it promote 15NO3- uptake from agar plates to the leaves of the host under N-sufficient or N-limiting conditions. However, when the roots were co-cultivated with 15N-labelled P. indica, more label can be detected in the leaves of N-starved host plants, but not of plants supplied with sufficient N. Amino acid and primary metabolite profiles, as well as expression analyses of N metabolite transporter genes suggest that the fungus alleviates the adaptation of its host to the N limitation condition. P. indica alters the expression of transporter genes which participate in relocation of NO3-, NH4+ and N metabolites from the roots to the leaves under N limitation. We propose that P. indica participates in the plant´s metabolomic adaptation to N limitation by delivering reduced N metabolites to the host, alleviating metabolic N starvation responses, and reprogramming the expression of N-metabolism related genes.

Controlled drainage (CD) is an important agricultural measure for maintaining soil moisture and nutrients, controlling groundwater level, and increasing crop yield. In arid regions, CD can be used to improve the water supply in agriculture and reduce environmental pollution. In this study, we investigated the effect of CD, including a drainage depth of 40 cm (CWT1) and 70 cm (CWT2) during the plant growth period, free drainage (FD), and open ditch drainage (OD) on the migration of water, nutrients, and salts in the soil; the dynamics of groundwater level; the loss of soil nitrogen; and the growth of oilseed sunflower plants. Compared with FD, CD increased the water and nutrient content in the soil, reduced nitrogen loss, and enhanced the ability of the soil to continuously supply nitrogen to the oilseed sunflower plants, which benefited plant growth at later growth stages and reduced environmental pollution. During the period between irrigation at the budding stage and harvest stage, the average soil water content in the 0–20 cm soil layer in CWT1 increased by 3.67%, 4.78%, and 0.55%, respectively, compared with that in CWT2, FD, and OD. The soil mineral content in CWT1 was 25.17%, 35.05%, and 17.78% higher than that in CWT2, FD, and OD, respectively, indicating that higher soil salinity occurred at the later stage of plant growth in CWT1, which actually had little effect on the plants due to their enhanced salt tolerance and increased need for water and nutrients at that stage. In addition, CD delayed the decline in groundwater level, which allowed the plants to use groundwater at later growth stages, and as a result the yield and water use efficiency were improved. CWT1 significantly increased oilseed sunflower yield by 4.52–11.14% and increased water use efficiency by 1.16–10.8%. Moreover, CWT1 also increased the survival rate of the oilseed sunflower plants by 2.62–2.92%, and the plants demonstrated good growth. Therefore, under CD conditions, plants used soil water and nitrogen more efficiently and, as a result, their productivity was increased, and the water quality was improved.

Nitrogen and phosphorous support the ecosystem by supplying nutrients to algae and aquatic plants. Having them in excess results in the eutrophication of waters creating quality problems. In the past, nitrogen has been widely investigated for wells in the context of groundwater flow. However, a national-scale nitrogen assessment in rivers and streams has not received enough attention. In this research, the Wilcoxon rank sum test, as a non-parametric hypothesis testing method, has been applied to nitrogen concentration in the form of nitrate-nitrogen and nitrite-nitrogen in rivers and streams of the Contiguous United States. This approach was particularly selected because of the non-normal and positively skewed nitrogen levels occurring in the surface flow. This method was able to identify the impaired body of waters as well as quantify the confidence, significance, and errors involved. The Northern Appalachians (NAP), Northern Plains (NPL), and Xeric (XER) ecoregions were worsening in the nitrogen-nitrate condition with NAP, and XER needed immediate actions. The nitrite-nitrogen condition did not pose an immediate threat, so mitigation plans should focus more on nitrate-nitrogen remediation. It was shown that the method was superior to the two-sample t-test by yielding lower type II errors.

Carbon and nitrogen contents and their isotopic components and AMS radiocarbon dating ages were measured for 57 coastal sediments from Weizhou Island to analyze the distribution of total inorganic carbon (TIC) and its carbon and oxygen isotopic components (δ13Ccarb and δ18Ocarb), total organic carbon (TOC) and total nitrogen (TN) contents and their stable isotopic components (δ13CTOC and δ15NTN) and environmental significance. The results showed that the oldest age of coastal sediments on Weizhou Island was 2750 cal. a BP, and the average TIC contents of A1, A2, B1, C1, and D1 in the intertidal zone were all greater than 5%, where δ13Ccarb and δ18Ocarb were enriched, while the TIC contents in A3, C2, and D2 of the supra-tidal zone were low, where δ13Ccarb and δ18Ocarb were depleted. Moreover, TIC decreased sharply from the estuary to upstream region in the C1-C2 section. The average C/N ratio was 7.02, and δ13CTOC and δ15NTN were between -14.96‰~-27.26‰ and -14.38‰~4.12‰, respectively. These measurements indicated that the TIC in coastal sediments mainly came from seawater. A1, A2, and B1 in the northern intertidal zone exhibited organic terrestrial signals because of C3 and C4 plant inputs, which proved that the important source of the northern coast of Weizhou Island came from the island. The lacustrine facies deposits were mainly distributed in the upper reaches of the river, the northern coastline was rapidly advancing toward the sea, and part of the southwestern coastal sediments rapidly accumulated to the shore under the influence of a storm surge. The relative sea level of the Weizhou Island area has continuously declined at a rate of approximately 2.07 mm/a, using beach rock as a marker, since the Holocene.

Agriculture (crop production, land use, and livestock) is the second most important greenhouse gas (GHG) emitting sector after the energy sector. Agriculture is also recognized as the source and sink of GHGs. Evidence demonstrates that the application of high amounts of nitrogen-rich fertilizers enhances methane (CH4) and nitrous oxide (N2O) emissions, which are potent GHGs with a high global warming potential (GWP). Considering its global contribution to the climate crisis, reducing GHG emissions in agriculture would considerably lower its share of the global GHG emission records, which may lead to enormous benefits for the environment and food production systems. Several diverging and controversial views questioning the actual role of plants in the current global GHG budget continue to nourish the debate globally. We must acknowledge that considering the beneficial roles of major GHGs to plants at a certain level of accumulation, implementing GHG mitigation measures from agriculture is indeed a complex task. This review seeks to provide key approaches for GHG mitigation in the literature (environmentally friendly crop cultivation and residue management practices, improvement of plants nutrients/fertilizer use efficiency, exploring the genetic diversity for low GHG emission, soil methane-producing bacteria, integrated soil fertility management, improved livestock feeding efficiency, and production, etc.). This work gathers key approaches from 275 peer-reviewed publications, including experimental research papers, review articles, and books, discussing greenhouse gas emissions mechanisms and mitigation to unravel effective strategies for GHG mitigation, proven to be effective or carry the potential to mitigate GHG generation from agriculture. This review also discusses in depth the significance and the dynamics of strategies regarded as game changers with a high potential to enhance, in a sustainable manner, the resilience of agricultural systems. Agricultural GHG mitigation approaches discussed in this work can serve as game changers in global efforts to reducing GHG emissions and alleviating the impact of climate change through sustainable agriculture and informed-decision making.

As the use of microbial inoculants in agriculture rises, it becomes important to understand how the environment may influence microbial ability to promote plant growth. This work examines whether there are light dependencies in the biological functions of Azospirillum brasilense, a commercialized prolific grass-root colonizer. Though classically defined as non-phototrophic, A. brasilense possesses photoreceptors that could perceive light conducted through its host’s roots. Evidence for light dependency of four microbial processes were examined and noted: biological nitrogen fixation (BNF), auxin biosynthesis, ATP biosynthesis, and iron and manganese uptake. Functional mutants of A. brasilense were leveraged and studied in light and dark environments: HM053 (high BNF and auxin production), ipdC (capable of BNF, deficient in auxin production), and FP10 (capable of auxin production, deficient in BNF). HM053 exhibited the highest rate of nitrogenase activity with the greatest light dependency comparing iterations in light and dark environments. The ipdC mutant showed similar behavior with relatively lower nitrogenase activity observed, while FP10 did not show a light dependency. Auxin biosynthesis showed strong light dependencies in HM053 and FP10 strains, but not for ipdC. Iron is involved in the BNF biological process, and light dependency was observed for microbial 59Fe2+ uptake in HM053 and ipdC, but not FP10. Surprisingly, a light dependency for 52Mn2+ uptake was only observed in ipdC. Finally, ATP biosynthesis was sensitive to light across all three mutants favoring blue light over red light compared to darkness with observed ATP levels in descending order for HM053 > ipdC > FP10.

The variability observed in the annual seed production of perennial plants can be seen as an indication of changes in the allocation of resources between growth and reproduction, which can be attributed to fluctuations in the environment. However, a significant knowledge gap exists concerning the impacts of nitrogen addition on the interannual seed production patterns of perennial plant. We hypothesized that the addition of nitrogen would impact the annual variations in the seed production of perennial plants, ultimately affecting their overall reproductive efficiency. A multiyear field experiment was conducted to investigate the effects of varying nitrogen supply levels (e.g., 0, 4, 8 kg N ha−1 yr−1 of N0, N4, and N8) on the vegetative and floral traits, pollinator visitation rates, and seed traits over a period of four consecutive years. The results showed that the N0 treatment exhibited the highest levels of seed production and reproductive efficiency within the initial two years. In contrast, the N4 treatment displayed its highest level of performance in these metrics in the second and third years, whereas the N8 treatment showcased its most favorable outcomes in the third and fourth years. The similar patterns were found in the number of flowers per capitulum and the number of capitula per plant. There exists a positive correlation between aboveground biomass and several factors, encompassing the number of flowers per capitulum, the number of capitula per plant, the volume of nectar per capitulum, and the seed production per plant. This implies that the addition of N affected the maintenance of plant aboveground biomass, flower traits stability and, subsequently, the frequency of seed production, and the reproductive efficiency. Our results suggest that augmenting the nitrogen content in the soil may have the capacity to modify the inherent variability in seed production that is observed across various years. These findings have the potential to enhance our comprehension of the impact of nitrogen addition on the reproductive performance of perennial herbaceous plants, and the underlying mechanisms of biodiversity in the context of global environmental changes.

A new coronavirus (SARS-CoV-2) have determined a pneumonia outbreak in China (Wuhan and Hubei) on December 2019. While pharmaceutical and non-pharmaceutical intervention strategies are strengthened worldwide, the scientific community has been studying the risk factors associated with SARS-Cov-2, to enrich epidemiological information. For a long time, before the industrialized era, air pollution has been a real and big health concern and it is today a very serious environmental risk for many diseases and anticipated deaths in the world. It has long been known that air pollutants increasing the invasiveness of pathogens for humans by acting as a carrier and making people more sensitive to pathogens through a negative influence on the immune system. Based on scientific evidences, the hypothesis that air pollution, resulting from a combination of factors such as meteorological data, level of industrialization as well as regional topography, can acts both as an infection carrier as a harmful factor of the health outcomes of COVID-19 disease has been raised recently. This hypothesis is turning in scientific evidence, thanks to the numerous studies that have been launched all over the world. With this review, we want to provide a first unique view of all the first epidemiological studies relating the association between air pollution and SARS-CoV-2. Major findings are consistent, highlighting the important contribution of air pollution on the COVID-19 spread and with a less extent also PM₁₀.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

The solid-state technique was utilized to make a single phase of delafossite CuAlO2, along with 1%, 2%, 3% and 4% silver doped CuAlO2 samples in this study. The content of the samples was investigated using energy dispersive X-ray spectroscopy (EDS) equipped with a field emission scanning electron microscope (FE-SEM). The polycrystalline nature of all of the analyzed cases was confirmed by structural analyses utilizing an X-ray diffraction (XRD) pattern with a simple typical peak of CAO rhombohedral phase. Raman, FT-IR and UV–Vis spectroscopy were used to study the structural, and optical energy band gap (Eg) of Ag doped CuAlO2 nanoparticles. The Kubelka–Munk function was used to calculate the optical band gap of ACAO alloys using diffuse reflectance spectra, and it altered as the Ag ion concentration increased. A. c. impedance spectroscopy was used to investigate the dielectric characteristics of Ag doped CuAlO2 nanoparticles.

Mn-doped CeO2 and CeO2 with the same morphology (nanofiber and nanocube) were synthesized through hydrothermal method respectively. When applied to benzene oxidation, the catalytic properties of Mn-doped CeO2 were higher than those of CeO2, which was related with the concentration of O vacancy. Compared to CeO2 with the same morphology, more oxygen vacancies were formed on the surface of Mn-doped CeO2, due to Mn ion replacing Ce ion. The lattice replacement was analyzed through XRD, Raman, electron energy loss spectroscopy and electron paramagnetic resonance technology. The formation energies of oxygen vacancy on the different exposed crystal planes [(110) and (100)] for Mn-doped CeO2 were calculated by applying the density functional theory (DFT). The data showed that the oxygen vacancy was easier to be formed on the (110) plane. The factors influencing catalytic behavior were elaborated, which indicated that surface oxygen vacancy played an important part in catalytic reaction.

Cobalt ferrite nanoparticles (NPs) doped with rare earth (RE) metals with general formula CoFe_2-xRE_xO₄ (RE=Yb, Dy, Gd; x = 0.0 - 0.3) were synthesized by the co-precipitation method followed by post thermal treatment. The influence of RE doping on structural, magnetic and thermal properties and potential biomedical applications like magnetic hyperthermia has been investigated. In the as-prepared samples RE cations enter the spinel lattice as detected by X-ray diffraction. Thermal treatment leads to thermodynamically stable and relaxed single-phase spinel structures only for lower RE content, x = 0.01-0.05. However, annealed samples present higher mass magnetization values (M_S), up to 83 Am²/kg. RE content also affects M_S, especially in the case of annealed samples where it decreases linearly with x from about 80 Am²/kg (x = 0.01) to about 60 Am²/kg (x = 0.30). Thermal treatment induces a reduction in coercivity from 60-100 mT for as-prepared samples to 18-33 mT for annealed samples, in a nonlinear manner with respect to RE content. Heating efficiency, i.e., Specific Loss Power (SLP), of all samples has been studied using both magnetometric and calorimetric method to deeper examine the energy loss mechanisms involved.

Adding a submerged zone (SZ) is deemed to promote denitrification during dry periods and thus improve NO3--N removal efficiency of a bioretention system. However, few studies had investigated the variation of nitrogen concentration in the SZ during dry periods and evaluated the effect of the variation on nitrogen removal of the bioretention system. Based on the experiment in a mesocosm bioretetion system with SZ, this study investigated the variation of nitrogen concentration of the system under 17 consecutive cycles of wet and dry alternation with varied rainfall amount, influent nitrogen concentration and antecedent dry periods (ADP). The results indicated that (1) during the dry periods, NH4+-N concentrations in SZ showed an exponential decline trend, decreasing by 50% in 12.9 ± 7.3 hours; while NO3--N concentrations showed an inverse S-shape decline trend, decreasing by 50% in 18.8 ± 6.4 hours; (2) during the wet periods, NO3--N concentration in the effluent showed an S-shape upward trend; and at the early stage of the wet periods, the concentration was relatively low and significantly correlated with ADP, while the corresponding volume of the effluent was significantly correlated with the SZ depth; (3) in the whole experiment, the contribution of nitrogen decrease in SZ during dry periods to NH4+-N and NO3--N removal accounted for 12% and 92%, respectively; and the decrease of NO3--N in SZ during the dry period was correlated with the influent concentration in the wet period and the length of the dry period.

We analyzed the plant-litter-soil continuum to investigate the carbon and nitrogen distribution and ecological stoichiometry of an evergreen broad-leaved forest at Dagangshan Mountain, Jiangxi. The results showed that the average C and N contents and C:N ratios in the leaves and fine roots among 6 different tree species were 401.87g/kg, 21.41g/kg, 19.27 and 348.64g/kg, 15.73g/kg, 23.97, respectively; the average C and N contents and C:N ratios were 323.06 g/kg, 12.76 g/kg, 25.58 respectively in leaf litter, and 16.40 g/kg, 1.09 g/kg, 16.27 respectively for soil. In contrast with the C content, the total N content of the fine roots and litter had a high coefficient of variation and a high spatial heterogeneity. We ranked the six different representative tree species according to total C and N content in leaves and fine roots. The results for each species were generally consistent with each other, showing a positive correlation relationship between total C and N content in the leaves and roots. Among them, S. discolor (Champ. ex Benth.) Muell. plants displayed high carbon and nitrogen storage capacities, and on the other hand, C. fargesii Franch., C. myrsinifolia (Blume) Oersted, A. fortunei (Hemsl.) Makino, and V. fordii (Hemsl.) Airy Shaw showed a high nitrogen transfer rate. Total soil N and C decreased with depth. Soil organic carbon (SOC), soil resistant organic carbon (ROC), total N, alkali nitrogen, NH4+-N and NO3--N contents were all also negative correlated with soil depth, but the contents of the NH4+-N and NO3--N did not change significantly; The spatial distribution of soil NO3--N was significantly heterogeneous. At 0-10 cm soil depth, SOC was positively correlated with alkaline nitrogen, and at 10-20 cm soil depth, SOC was significantly positively correlated with total N. In general, when soil carbon was abundant, nitrogen supply capacity was also high.

Urban stormwater runoff from a medium-density residential development in southeast Queensland has been monitored in the field since November 2013. A treatment train installed on the site includes rainwater tanks collecting roofwater, 200-micron mesh baskets installed in grated gully pits and two 850 mm high media filtration cartridges installed in an underground 4 m³ vault. A monitoring protocol developed by research partners, Queensland University of Technology (QUT), guided the monitoring process over a 4.5-year period. Heavy metals were included in the list of analytes during the monitoring period as the catchment is within 1 km of the environmentally-sensitive Moreton Bay, Queensland. Removal efficiencies observed at this site for the regulated pollutants; total suspended solids (TSS), total phosphorus (TP) and total nitrogen (TN) for the pit baskets were 61%, 28% and 45% respectively. The cartridge filters removed 78% TSS, 59% TP, 42% TN, 40% total copper and 51% total zinc. As the measured influent concentrations to the cartridge filters were low when compared to industry guidelines, the dataset was merged with international field results for TSS (n=39) and TP (n=32) but truncated within anticipated guideline levels. The combined dataset for the media filter demonstrates performance at 89% TSS, 66% TP and 42% TN. The total gross pollutant generation rate from the medium-density residential catchment was observed to be 0.24 m³/Ha/year, with a corresponding air-dried mass of 142.5 kg/Ha/year. Less than 2% of the gross pollutant mass was anthropogenic. The findings of this research suggest that the treatment train, and in particular the media filter, holds promise for the removal of total copper and total zinc, in addition to TSS, TP and TN, from urban stormwater runoff. Based on a maximum, low risk trigger TN concentration of 1.5 mg/L, the field test data from 4.5 years of operation and standard maintenance, suggests a 5.5-year replacement interval for the media filters.

Many studies have found that future predicted CO2 levels (< 800 ppm) can increase plant mass but dilute N content in leaves, impacting antiherbivore compounds. Nitrogen-fixing plants may balance leaf C:N ratio under elevated CO2, counteracting this dilution effect. The aim of this study was to look at how nitrogen-fixing plants grow and respond to herbivore damage at different CO2 levels. Alnus incana ssp. rugosa was grown at 400, 800, or 1600 ppm CO2 in soil collected from the field, inoculated with Frankia and exposed to herbivores (Orgyia leucostigma). Elevated CO2 increased nodulated plant biomass and stimulated the nitrogen fixation rate in the early growth stage. However, nitrogen-fixing plants were not able to balance the C:N ratio under elevated CO2 after grown 19 weeks. When plant were grown at 400 and 1600 ppm CO2, herbivores preferred to feed on leaves of nodulated plants. At 800 ppm CO2, nodulated plants accumulated more total phenolic compounds in response to herbivore damage than plants in the non-Frankia and non-herbivore treatments. Our results suggest that plant leaf defence, not leaf nutritional content, is the dominant driver of herbivory and nitrogen fixing plants have limited ability to balance C:N ratios at elevated CO2 in natural soil.

Rice cultivation serves as a significant anthropogenic source of methane (CH4), a primary greenhouse gas, and nitrous oxide (N2O), a secondary greenhouse gas. Although N2O emissions remain relatively small compared to CH4 emissions, they are remarkably affected by nitrogen-fertilized soil conditions during rice cultivation. To date, investigations are very limited concerning N2O emissions from rice cultivation in relation to environmental factors such as temperature, rainfall, and soil properties. In this case study, we investigated the characteristics of N2O emissions in the central region of South Korea, where a single rice cropping cycle occurs annually over a span of three years, from May 2020 to May 2023. We investigated the impact of variations in temperature and soil moisture on N2O emissions during rice cultivation. In this context, we attempted to discover the complex dynamics of N2O emissions by comparing longer fallow periods with the rice cultivation periods and extended non-dry periods with irrigated periods. We observed that extremely high N₂O flux events encountered during the fallow period appeared to have a substantial impact on the yearly cumulative N₂O emissions, surpassing the impact of cumulative N₂O emissions during the rice cultivation period. We found that high N₂O flux events arose not only from artificial nitrogen inputs but also due to temperature and soil moisture variations influenced by weather conditions. We concluded that assessing N₂O emissions solely based on the rice cultivation period would underestimate annual emissions. To prevent underestimation of N₂O emissions, continual gas collection throughout a year covering both rice cultivation and fallow phases is required in align with monitoring of varying temperature and soil moisture conditions. Based on our findings, we recommend that at least a three whole year evaluation period is needed to ensure estimation accuracy of N₂O emissions under varying nitrogen fertilization rates. Also, the findings from this study would help prepare a further revision or refinement of N2O emission factor from rice cultivation in the national greenhouse gas inventories defined by the inter-governmental panel on climate change (IPCC).

Nitrogen dioxide (NO₂) contributes to several impacts both for human health and the environment. Periodical measurement of NO₂ at industrial and residential areas needs comprehensive and reliable instrumentation; long-interference-free measures with minimum maintenance and re-calibration. DOAS can be used as a direct measurement technique based on specific absorption characteristics of NO₂ follow Beer-Lambert law. This research applies a low-cost folded path photometer for measurement NO₂ in air. Cheap tubular acrylic used as a detection cell with a 3D printed framework makes it compact, modular, and flexible. Evaluation of the DOAS conducted by instrument test responses using NO₂ gas. The estimated LOD was ~ 1263 pb using 2 nm resolution of the spectrometer and 6-meter detection cell length. Deviation of the DOAS estimated to be 0.8% at high concentration and 2.85% at a low concentration based on DOAS calibration. An intercomparison between methods used to evaluate instrument performance to measure NO₂ using emission from a motorcycle with coefficient correlation (R) 0.649 for paired DOAS-ASTM D1607 Griesz Saltzmann Method 0.846 for paired DOAS-Electrochemical Gas Analyzer. This significant correlation is caused by different respond time between paired methods, while it is still comparable for NO₂ measurement.

A field experiment was conducted during Kharif 2018, laid out in Randomized Block Design with three replications having seven treatments viz. N omission (T1), N applied as basal and AT (T2), N as basal, AT and PI (T3), N as basal and top dressing at NDVI threshold of 0.75 (T4), at NDVI threshold of 0.8 (T5), at SPAD threshold of 35.0 (T6) and SPAD threshold of 37.5 (T7) with Rice variety Sahabhagidhan.The study revealed that application of 30 kg N/ha as basal dose and top dressing of 20 kg N/ha twice at 35 and 63 DAS guided by NDVI threshold value of 0.8 (T5) was found to be superior over other treatments with respect to productivity. T5 recorded highest grain yield of 4438 kg/ha which was 17.0% higher than that top dressed at NDVI threshold of 0.75 (T4) and 7.1% higher than that top dressed at SPAD threshold value of 37.5 (T7). In case of SPAD meter, nitrogen top dressed at threshold value of 37.5 (T7) produced grain yield of 4143 kg/ha which was 15.0% higher than T6. T5 produced maximum dry matter of 8678 kg/ha with highest grain yield (4438 kg/ha), straw yield (5092 kg/ha) and harvest index 46.0%.

Here, we report the draft genome sequence of the type strain of Ideonella azotifigens DSMZ21438^T (formally 1a22^T = JCM15503^T). Ideonella azotifigens DSMZ21438T a novel betaproteobacterial non-symbiotic nitrogen-fixing grass rhizosphere dwelling microbe. The 891,561 paired-end shotgun reads were quality filtered and decontaminated with the ATLAS pipeline, then assembled with Unicycler. The genome size is 6,257,981 bp, an N50 size of 7,849 bp, with a G+C content of 66.71%, and with 5,882 predicted protein-coding genes. I. azotifigens DSMZ21438^T represents the first member of the genus isolated from rhizosphere soil, providing a framework for further study into non-alphaproteobacterial nitrogen fixation and synthetic biology applications.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

There was a question on “how lanthanides doping in iron oxide affects cure kinetics of epoxy-based nanocomposites?” To answer, we synthesized samarium (Sm)-doped Fe3O4 nanoparticles via electrochemical method and characterized it using FTIR, XRD, FE-SEM, EDX, TEM, and XPS analyses. The magnetic particles were uniformly dispersed in epoxy resin to increase the curability of the epoxy/amine system. The effect of the lanthanide dopant on the curing reaction of epoxy with amine was explored by modeling DSC experimental data based on model-free methodology. It was found that Sm3+ in the structure of Fe3O4 crystal participates in cross-linking of epoxy by catalyzing the reaction between epoxide rings and amine groups of curing agents. In addition, the etherification reaction of active OH groups on the surface of nanoparticles reacts with epoxy rings which prolongs the reaction time at the late stage of reaction where diffusion is the dominant mechanism.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Antibiotic residues in aquatic environment have the possibility to induce resistance in environmental bacteria, which ultimately might get transferred to pathogens making treatment of diseases difficultand poses a serious threat to public health. If antibiotic residues in the environment can be eliminated or reduced, it has the possibility to contribute antibiotic resistance. Towards this objective, water containing ciprofloxacin was treated with sunlight assisted photocatalysis using Fe doped ZnOnanoparticles for assessing the degradation potential of this system.Parameters like pH, temperature, catalytic dosage were assessed for the optimum performance of the system. To evaluate degradation of ciprofloxacin,both spectrophotometricas well as microbiological (loss of antibiotic activity)methods were employed. 100 mg/L Fe doped ZnO nanoparticle catalyst and sunlight intensity of 120,000–135,000 lux system gave optimum performance at pH 9 at 30 °C and 40 °C. At these conditions spectrophotometric analysis showed complete degradation of ciprofloxacin (10mg/L) by 210 min. Microbiological studies showed loss of antibacterial activity of the photocatalytically treated ciprofloxacin containingwater against Staphylococcus aureus (10⁸ CFU) in 60 min and for Escherichia coli (10⁸ CFU) in 75 min. Thedeveloped system, thus possess a potential for treatment of antibiotic contaminated waters for eliminating/reducing antibiotic residues from environment.

Intercropping systems can flexibly use resources such as sunlight, heat, water, and nutrients in time and space, improve crop yield and land utilization rates, effectively reduce continuous cropping obstacles and the occurrence of diseases and insect pests, and control the growth of weeds. Thus, intercropping is a safe and efficient ecological planting mode. The legume–cereal intercropping system is the most common planting combination. Legume crops fix nitrogen from the atmosphere through their symbiotic nitrogen fixation abilities, and the fixed nitrogen can be transferred to and utilized by cereal crops in various ways. The symbiotic nitrogen fixation efficiency of legume crops was improved by reducing the inhibition of soil nitrogen on nitrogenase activity through competitive absorption of soil nitrogen. However, the effects of nitrogen transformation and distribution in intercropping systems, and microbial community structure characteristics on nitrogen transfer need to be further explored. In this review, ⅰ) we present the transformation and distribution of nitrogen in the legume–cereal intercropping system; ⅱ) we describe the soil microbial community characteristics in intercropping systems; and ⅲ) we discuss the advantages of using modern biological molecular techniques to study soil microorganisms. We conclude that intercropping can increase the diversity of soil microorganisms, and the interaction between different plants has an important impact on the diversity and composition of the bacterial and fungal communities. The extensive application of modern biological molecular techniques in soil microbial research and the great contribution of intercropping systems to sustainable agriculture are particularly emphasized in this review.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Lutein, a plant-derived xanthophyl-carotenoid, is an exceptional antioxidant and anti-inflammatory constituent found in food. Elevated concentrations of lutein found in human blood and plasma, due to high dietary intake, are beneficial against eye disease and improve cardiometabolic health. Lutein plays an important protective role against the development of neurological disorders, including Alzheimer’s disease (AD), multiple sclerosis (MS) and Parkinson’s disease (PD). It has also been shown to be beneficial for liver, kidney and respiratory health. Lutein, acting as a very strong antioxidant, can alleviate oxidative stress and downgrade reactive oxygen species (ROS). Oxidative stress is one of the key pathogenic mechanisms in post-COVID and mRNA vaccine injury syndromes. Recent in silico studies suggest that lutein and other naturally derived antioxidants, by docking at the site where the SARS-CoV-2 spike protein (SP) binds to the angiotensin enzyme type 2 (ACE2) receptor, may neutralize the SP-ACE2 interactions. Lutein can be added to a detoxification regimen to aid in clearing Spike protein and relieving symptoms. In agreement with Hippocrates’ dictum to “Let food be thy medicine,” this review establishes dietary lutein as a valuable therapy in the treatment of post-COVID syndrome, mRNA vaccine injury syndromes, and a wide range of other chronic illnesses.

Nitrogen use efficiency (NUE) in maize (Zea mays L.) is an important trait to maximize yield with minimal input of nitrogen (N) fertilizer. Expired Plant Variety Protection (ex-PVP) Act-certified germplasm may be an important genetic resource for public breeding sectors. The objectives of this research were to evaluate the genetic variation of N-use traits and to characterize maize ex-PVP inbreds adapted to the U.S. Corn Belt for NUE performance. Eighty-nine ex-PVP inbreds [36 stiff stalk synthetic (SSS), and 53 non-stiff stalk synthetic (NSSS)] were genotyped using 26,769 single-nucleotide polymorphisms, then 263 single-cross maize hybrids derived from these inbreds were grown in eight environments from 2011 to 2015 at two N fertilizer rates (0 and 252 kg N ha⁻¹) and three replications. Genetic utilization and the yield response to N fertilizer were stable across environments and were highly correlated with yield under low and high N conditions, respectively. Cluster analysis identified inbreds with desirable NUE performance. However, only one inbred (PHK56) was ranked in the top 10% for yield under both N-stress and high N conditions. Broad-sense heritability across 12 different N-use traits ranged from 0.11 to 0.77, but was not associated with breeding value accuracy. Nitrogen-stress tolerance was negatively correlated with the yield increase from N fertilizer.

The legume-rhizobia symbiosis is one of the most important plant-microbe interactions in sustainable agriculture due to its ability to provide much needed N to cropping systems. This interaction is mediated by the mutual recognition of signaling molecules from the two partners, namely legumes and rhizobia. With legumes, these molecules are in the form of flavonoids and anthocyanins, which are responsible for the pigmentation of plants parts, such as seeds, flowers, fruits and even leaves. Seed coat pigmentation in legumes is a dominant factor influencing gene expression relating to N2 fixation, and may be responsible for the different N2-fixing abilities observed among legume genotypes under field conditions in African soils. Cowpea, Kersting’s bean and Bambara groundnut landraces with black seed coat color are reported to release higher concentrations of nod-gene-inducing flavonoids and anthocyanins when compared to the Red and Cream landraces, hence the black seed coat pigmentation is considered a biomarker for enhanced nodulation and N2 fixation. Cowpea, Bambara groundnut and Kersting’s bean with differing seed coat colors are known to attract different native soil rhizobia, confirmable by PCR-RFLP analysis of bacterial DNA from root nodules of these legumes. Even when seeds of the same legume with diverse seed coat colors were planted together in one hole, the nodulating bradyrhizobia clustered differently in the PCR-RFLP dendrograms. In one study, Kersting’s groundnut, Bambara groundnut and cowpea with differing seed coat colors were selectively nodulated by different bradyrhizobial species. Multilocus sequence analysis showed that different Bradyrhizobium species nodulated the Kersting's bean based on seed coat color. Phylogenetic analysis also placed the bradyrhizobial isolates in close proximity to different Bradyrhizobium species such as B. vignae 7-2T, B. subterraneum 58 2-1T, B. kavangense 14-3T, B. liaoningense 2281 (USDA 3622)T, B. yuanmingense LMG 21827T, B. huanghuaihaiense CCBAU 23303T, B. pachyrhizi PAC48T, and a reference type strain of B. elkanii according to seed coat color. Using 16S rDNA amplicon sequencing, we also found significant selective influences of seed coat pigmentation on microbial community structure in the rhizosphere of five Kersting’s groundnut landraces. For example, the rhizosphere of Belane Mottled landrace was dominated by Proteobacteria, while Bacteroidetes dominated the rhizospheres of the other landraces. With legumes, seed coat pigmentation therefore plays a dominant role in the selection of the bacterial symbiotic partner.

Cancer cells require substantial amounts of energy and substrates for their metabolic hyperactivity, enabling the synthesis of new cells at the expense of healthy ones. Preliminary in vitro data suggest that a mix of free essential amino acids (EAA-mix) can promote cancer cell apoptosis by enhancing autophagy. This study aimed to confirm, both in vitro and in vivo, whether EAA intake could influence the development of colon cancer in mice. We investigated changes in cancer proliferation in CT26 cells treated with EAA-mix, and in mice fed with EAA rich modified diets (EAARD) as compared to those on a standard laboratory diet (StD). CT26 cells were injected subcutaneously (s.c.) or intraperitoneally (i.p.). After 21 days, tumors were removed and measured. In vitro data corroborated that EAA-mix impairs cancer growth by inducing autophagy and apoptosis. In vivo data revealed that mice on StD developed significantly larger (s.c.) and more numerous (i.p.) cancers than those on EAARD. EAA administration appears to influence cancer cell survival with notable anti-proliferative properties.

Excessive nitrogen application has become a hidden danger threatening the sustainable development of agriculture. Exploring the potential genes will help to improve the nitrogen availability of wheat through molecular breeding. We therefore conducted wheat transcriptomics and proteomics researches under complete culture medium without nitrogen (N0) and complete culture medium with nitrogen (N1). The results showed that, the nitrogen deficit decreased the fresh weight, N content and net photosynthetic rate of winter wheat. 3949 and 2675 differentially expressed genes (DEGs) were identified in the shoot and root, respectively, while 164 and 129 differentially expressed proteins (DEPs) were identified in the shoot and root respectively. 9 genes in shoot and 26 genes in root showed the same trends in RNA and protein levels. 5 genes in shoot and 4 genes in root showed the opposite trends in RNA and protein levels. Pathway enrichment of wheat transcriptome and proteome under nitrogen deficit proposed 3 candidate genes related to photosynthesis in shoot, 4 candidate genes related to carbon metabolism in shoot, and 12 candidate genes related to carbon metabolism in root. Meanwhile, the chromosomal and subcellular localization of these genes were listed, which will provide reference for improving nitrogen availability through molecular breeding.

Rapeseed (Brassica napus L.) is one of the most important oil crops in China. Improving oil production of rapeseed is an important way to ensure the safety of edible oil in China. Oil production is an important index to reflect the quality of rapeseed and is determined by oil content and yield. Applying nitrogen is an important way to ensure a high yield. However, increasing nitrogen application would decrease oil content. Thus, it is critical to screen elite germplasm resources with stable or improved oil content under high nitrogen and to investigate the molecular mechanisms of nitrogen regulation of oil accumulation. In this paper, we review the effects of nitrogen levels on rapeseed yields and oil content, aiming to reveal the mechanisms of nitrogen regulation in oil accumulation and thereby provide a theoretical basis for breeding varieties with high oil content.

Microalgae are used in various biotechnological processes, such as biofuel production due to their high biomass yields, agriculture as biofertilizers, production of high-value-added products, de-contamination of wastewater, or as biological models for carbon sequestration. The number of these biotechnological applications is increasing, and as such, any advances that contribute to reducing costs and increasing economic profitability can have a significant impact. Nitrogen fixing organisms, often called diazotroph, also have great biotechnological potential, mainly in agri-culture as an alternative to chemical fertilizers. Microbial consortia typically perform more com-plex tasks than monocultures and can execute functions that are challenging or even impossible for individual strains or species. Interestingly, microalgae and diazotrophic organisms are capable to embrace different types of symbiotic associations. Certain corals and lichens exhibit this sym-biotic relationship in nature, which enhances their fitness. However, this relationship can also be artificially created in laboratory conditions with the objective of enhancing some of the biotech-nological processes that each organism carries out independently. As a result, the utilization of microalgae and diazotrophic organisms in consortia is garnering significant interest as a potential alternative for reducing production costs and increasing yields of microalgae biomass, as well as for producing derived products and serving biotechnological purposes. This review makes an effort to examine the associations of microalgae and diazotrophic organisms, with the aim of highlighting the potential of these associations in improving various biotechnological processes.

Developing advanced carbon materials by utilizing biomass waste has attracted much attention. Herein, a N-doped carbon material (RSM-0.33-550) was prepared by directly pyrolyzing reed straw and melamine. The as-prepared RSM-0.33-550 possessed a N content of 6.02% and a specific surface area of 547.1 m2 g-1. As the anode for supercapacitors (SCs), in 6 M KOH, such RSM-0.33-550 exhibited a capacitance of 202.8 F g-1 at a current density of 1 A g-1. At a high current density of 20 A g-1, it still remained a capacitance of 158 F g-1. Notably, it delivered an excellent stability with capacity retention of 96.3% at 20 A g-1 after 5000 cycles. This work not only offer a new electrode material for SCs, but also gives a new insight for rationally utilizing the biomass waste for energy storage.

Abstract: Cancer cells are originated by normal cells and with those share the need to be fed. Metabolic reprogramming in cancer cells is not yet fully understood although there is a vast literature suggesting that huge amounts of both energy and substrates are require for synthesis of components of new neoplastic cells so that any macronutrient may be efficiently utilized. Recently, in vitro data show that EAA supplementation promoted colon cancer cells apoptosis by enhanced autophagy. Therefore, in this study we tested in vivo the effects of matched macronutrients standard laboratory diet (control) versus EAA rich modified diet (EAArmd) in mice injected with colon cancer cells. Results of the first set of 12 animals, 6 controls and 6 EAArmd-fed, showed that controls mice develop cancer volume cancers 5 times larger and heavier than EAArmd-fed. If confirmed, these results would open new scenarios for the cancer integrate therapies.