This paper describes methods for evaluating the thermal properties of textile materials, clothing composites, and clothing using an integrated measurement system that includes a hot plate, a multi-purpose differential conductometer, a thermal manikin, a temperature gradient measurement device, and a device for measuring the physiological parameters of the human body during the exact evaluation of garment thermal comfort. In practice, measurements were taken on four types of materials widely used in the production of conventional and protective clothing. The measurements were carried out using a hot plate and a multi-purpose differential conductometer, determining the thermal resistances of the material in its uncompressed form and a force that was ten times greater than that needed to determine its thickness. Using a hot plate and a multi-purpose differential conductometer, thermal resistances of textile materials were assessed at different levels of material compression. On hot plates, both conduction and convection had an impact on thermal resistance, but in multi-purpose differential conductometer, only conduction did. Moreover, the reduction of thermal resistance was observed while compressing textile materials.

Recently, torrential rain and drought have occurred in close temporal proximity and for similar durations due to changes in the spatiotemporal patterns of rainfall owing to climate change. In particular, when a drought occurs, it tends to be prolonged, making it necessary to improve the operation of multi-purpose dams that not only control flooding but also serve as water supplies. In this study, standard water volume lines and action plans by response stage were improved so that water could be stored in advance of a drought instead of reservoir operation criteria set based on data from the past. The minimum water demand by use (domestic water, industrial water, and agricultural water) was also calculated. The improved reservoir operation criteria were applied to multi-purpose dams in the Nakdong River Basin, and their effects were analyzed by calculating additionally secured water volumes. In the future, in case of lowered water volumes in multi-purpose dams owing to a drought, the application of these improved reservoir operation criteria is expected to contribute to water supply stability by delaying entry into the drought stage, and minimizing the damages caused by limited water supplies.

The major global pressures of rapid urbanization and urban growth are compounded by climate impacts resulting in increased vulnerability for urban dwellers, with these vulnerabilities exacerbated during COVID-19. Much of this is concentrated in urban and peri-urban areas where urban development spreads into hazard-prone areas. Often this development is dominated by poor quality homes in informal settlements or slums with poor tenure security. Lessons from a current resilience-building project shows that the fit-for-purpose (FFP) approach to land administration can provide a solution to increase the number of households with security of tenure and improve resilience outcomes as informal settlements grow. This paper discusses the influence of FFP land administration on vulnerabilities to multiple shocks related to climate change and COVID-19. This paper proposes ways the growth of human settlements can be better managed through responsible governance of land tenure rights, and effective land-use planning to improve resilience to different shocks and stresses and provide adequate access to safe land and shelter. Land administration systems can support improved resilience to the multiple stressors of climate and pandemics through improving tenure security and enhancing land use planning controls. Climate change adaptation and risk management need to be better mainstreamed into two major elements of land governance: (i) securing and safeguarding of land rights, and (ii) planning and control of land-use.

We provide methodology and numerical results for the Hattendorff differential equa- tion for the continuous time evolution of the variance of L(j)t , the loss at time t random variable for a multi-state process, given that the state at time t is j.

The study follows the interaction between the individual and the social context regarding the development of adolescents protected in residential houses from the child protection system in Iasi County, Romania. Starting from the evidence that in situations of providing relatively identical material and social resources, the results obtained by these children vary greatly, we examine how the meaning (understood mainly as purpose and mattering) can constitute a developmental resource. Considering theoretical models and previous research, the study aims to describe, through a qualitative approach, how these young people see themselves and the external environment (family and residential care), how they project their future (their purpose and objectives), and how these constructions and perceptions can influence their quality of life and social integration. We conducted three focus groups with 35 adolescents and young people (the ages 13-21) protected in and for different periods in residential houses (period 1-20 years). The results highlighted that a specific meaning is reconfigured as compensatory when affected by a trauma or adverse external event and thus can be a resource for resilience. On the other hand, the research highlighted that only the existence of goals alone is insufficient to generate action, and the unrealistic meanings given to own persons, experiences, and resources can be dangerous.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

Predicting trip purpose from comprehensive and continuous smart card data is beneficial for transport and city planners in investigating travel behaviours and urban mobility. Here we propose a framework, ActivityNET, using machine learning (ML) algorithms to predict passengers’ trip purpose from smart card data and Points-of-Interest (POIs) data. The feasibility of the framework is demonstrated in two phases. Phase I focuses on extracting activities from individuals’ daily travel patterns from smart card data and combining them with POIs using the proposed ‘activity-POIs consolidation algorithm’. Phase II feeds the extracted features into an artificial neural network (ANN) with multiple scenarios and predicts trip purpose under primary activities (home and work) and secondary activities (entertainment, eating, shopping, child drop-offs/pick-ups and part-time work) with high accuracy. As a case study, the proposed ActivityNET framework is applied in Greater London and illustrates a robust competence to predict trip purpose. The promising outcomes demonstrate that the cost-effective framework offers high predictive accuracy and valuable insights into transport planning.

Cross-field innovation in faba bean breeding has added significant value to the traditional faba bean planting industry by allowing for the selection of faba bean varieties with a dual purpose as ornaments and food. In order to improve the selection efficiency, we determined 17 phenotypes related to ‘dual purpose’ faba beans and evaluated 37 new breeding lines, which were bred for 10 years by our team, and two traditional faba bean varieties by means of an Analytic Hierarchy Process. The lines and varieties were evaluated and sorted into five grades, from which two breeding lines with excellent comprehensive phenotypes and dual ornamental and food functions were selected. The new line GS5 passed the identification of Crop Identification Committee of Chongqing Seed Industry Association on November 25, 2021 and was renamed "Doumei 1 hao" with the identification number of " 202111". The results confirmed that the comprehensive evaluation system constructed in this study can be used for the effective selection of dual-purpose faba bean lines, providing an empirical approach for strategic decision-making by breeders.

In daily travel and activities, pathfinding is a significant process. They are often used in transportation routes calculation. They have now evolved to be able to solve most situations of the pathfinding and its related problems. This review describes previous and recent studies on the pathfinding algorithms. It reviews the development of pathfinding algorithms in a classification base on their usage. The aim is to summarize the application of the pathfinding algorithms for the readers interested in the subject that can be used as a supplement.

Fit-for-purpose land administration (FFPLA) seeks to simplify cadastral mapping via lowering the costs and time associated with conventional surveying methods. The approach can be applied to both initial establishment and on-going maintenance of system. In Ethiopia, cadastral maintenance remains an on-going challenge, especially in rapidly urbanizing peri-urban areas, where farmers' land rights and tenure security are often jeopardized. Automatic Feature Extraction (AFE) is an emerging FFPLA approach, proposed as an alternative for mapping and updating cadastral boundaries. This study explores the role of the AFE approach for updating cadastral boundaries in the vibrant peri-urban areas of Addis Ababa. Open-source software solutions are utilized to assess the (semi-) automatic extraction of cadastral boundaries from orthophotos (segmentation), designation of 'boundary' and 'non-boundary' outlines (classification), and delimitation of cadastral boundaries (interactive delineation). Both qualitative and quantitative assessments of the achieved results (validation) are undertaken. A high-resolution orthophoto of the study area and a reference cadastral boundary shape file are used, respectively, for extracting the parcel boundaries and validating the interactive delineation results. Qualitative (visual) assessment verified the completed extraction of newly constructed cadastral boundaries in the study area, although non-boundary outlines such as footpaths and artefacts are also retrieved. For the buffer overlay analysis, the interactively delineated boundary lines and the reference cadastre were buffered within the spatial accuracy limits for urban and rural cadasters. As a result, the quantitative assessment delivered 52% correctness and 32% completeness for a buffer width of 0.4m and 0.6m, respectively, for the interactively delineated and reference boundaries. The study further demonstrated the potentially significant role AFE could assist in delivering fast, affordable, and reliable cadastral mapping. Further investigation, based on user input and expertise evaluation, could help to improve the approach and apply it to a real-world setting.

Multi-Faith Spaces (MFS) are a relatively recent invention that quickly gained in significance. On the one hand, they offer a convenient solution for satisfying needs of people with diverse beliefs in the institutional context of hospitals, schools, airports, etc. On the other hand, as Andrew Crompton pointed out, they are politically significant because the multi-faith paradigm “is replacing Christianity as the face of public religion in Europe” (2012, p. 493). Due to their ideological entanglement, MFS are often used as the means to promote either a more privatised version of religion, or a certain denominational preference. Two distinct designs are used to achieve these means: negative in the case of the former, and positive in the latter. Neither is without problems, and neither adequately fulfils its primary purpose of serving diverse groups of believers. Both, however, seem to follow the biases and main problems of secularism. In this paper, I analyse recent developments of MFS to detail their main problems and answer the question, whether the MFS, and the underlying Multi-Faith Paradigm, can be classified as a continuation of secularism.

Although there are several access control systems in the literature for flexible policy management in multi-authority and multi-domain environments, achieving interoperability & scalability, without relying on strong trust assumptions, is still an open challenge. We present HMBAC, a distributed fine-grained access control model for shared and dynamic multi-authority and multi-domain environments, along with Janus, a practical system for HMBAC policy enforcement. The proposed HMBAC model supports: (a) dynamic trust management between different authorities; (b) flexible access control policy enforcement, defined at domain and cross-domain level; (c) a global source of truth for all entities, supported by an immutable, audit-friendly mechanism. Janus implements the HMBAC model and relies on the effective fusion of two core components. First, a Hierarchical Multi-Blockchain architecture that acts as a single access point that cannot be bypassed by users or authorities. Second, a Multi-Authority Attribute Based Encryption protocol that supports flexible shared multi-owner encryption, where attribute keys from different authorities are combined to decrypt data distributedly stored in different authorities. Our approach was implemented using Hyperledger Fabric as the underlying blockchain, with the system components placed in Kubernetes Docker container pods. We experimentally validated the effectiveness and efficiency of Janus, while fully reproducible artifacts of both our implementation and our measurements are provided.

The paper proposes TOPSIS method for solving multi-objective multi-level programming problem (MO-MLPP) with fuzzy parameters via fuzzy goal programming (FGP). At first, - cut method is used to transform the fuzzily described MO-MLPP into deterministic MO-MLPP. Then, for specific , we construct the membership functions of distance functions from positive ideal solution (PIS) and negative ideal solution (NIS) of all level decision makers (DMs). Thereafter, FGP based multi-objective decision model is established for each level DM for obtaining individual optimal solution. A possible relaxation on decisions for all DMs is taken into account for satisfactory solution. Subsequently, two FGP models are developed and compromise optimal solutions are found by minimizing the sum of negative deviational variables. To recognize the better compromise optimal solution, the concept of distance functions is utilized. Finally, a novel algorithm for MO-MLPP involving fuzzy parameters is provided and an illustrative example is solved to verify the proposed procedure.

We develop an interactive likelihood (ILH) for sequential Monte-Carlo (SMC) methods for image-based multiple target tracking applications. The purpose of the ILH is to improve tracking accuracy by reducing the need for data association. In addition, we integrate a recently developed deep neural network for pedestrian detection along with the ILH with a multi-Bernoulli filter. We evaluate the performance of the multi-Bernoulli filter with the ILH and the pedestrian detector in a number of publicly available datasets (2003 PETS INMOVE, AFL, and TUD-Stadtmitte) using standard, well-known multi-target tracking metrics (OSPA and CLEAR MOT). In all datasets, the ILH term increases the tracking accuracy of the multi-Bernoulli filter.

One of the most important applications in the wireless sensor networks (WSN) is to classify mobile targets in the monitoring area. In this paper, a multi-DBN weighted voting classification algorithm is proposed on the basis of the Deep Belief Network (DBN) classifier and combined with the idea of voting method, which is implemented on the nodes of the WSN monitoring system by means of "upper training, lower transplantation" appraoch. The performance of the algorithm is verified by using real-world experimental data, and the results show that the proposed method has a higher accuracy in classifying the target signal features, achieving an average classification accuracy of 84.63% across four different types of moving targets. The experiment reveals that the multi-DBN weighted voting algorithm enhances the target classification accuracy by approximately 5% in comparison to the single DBN classifier, but the memory and computation time required for the algorithm to run are also increased at the same time. Compared to the FFNN classifier, which exhibited the highest classification accuracy among the four selected methods, the algorithm achieves an improvement of approximately 8.8% in classification accuracy. However, it incurs greater time overhead to run.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

Rapid assessment of maize yields in smallholder farming system is important to understand its spatial and temporal variability and for timely agronomic decision-support. Imageries acquired with unmanned air vehicles (UAV) offer opportunity to assess agronomic variables at field scale, however, it is not clear if this can be translated into reliable yield assessment on smallholder farms where field conditions, maize genotypes, and management practices vary within short distances. In this study, we assessed the predictability of maize grain yield using UAV-derived vegetation indices (VI), with(out) biophysical variables, in smallholder farms. High-resolution images were acquired with UAV-borne multispectral sensor at 4 and 8 weeks after sowing (WAS) on 31 farmers’ managed fields (FMFs) and 12 nearby Nutrient Omission Trials (NOT), all distributed across 5 locations within the core maize region of Nigeria. The NOTs included non-fertilized and fertilized plots (with and without micronutrients), sown with open-pollinated or hybrid maize genotypes. Acquired multispectral images were post-processed into several three (s) vegetation indices (VIs), normalized difference vegetation index (NDVI), normalized difference red-edge (NDRE), green-normalized difference vegetation index (GNDVI). Biophysical variables, plant height (Ht) and percent canopy cover (CC), were measured with the georeferenced plot locations recorded. In the NOTs, the nutrient status, not genotype, influenced the grain yield variability and outcome. The maximum grain yield observed in NOTs was 9.3 tha^-1, compared to 5.4 tha^-1 in FMF. Without accounting for between- and within-field variations, there was no relationship between UAV-derived VIs and grain yield at 4WAS (r<0.02, P>0.1), but significant correlations were observed at 8WAS (r≤0.3; p<0.001). Ht was positively correlated with grain yield at 4WAS (r=0.5, R²=0.25, p<0.001), and more strongly at 8WAS (r=0.7, R²=0.55, p<0.001), while relationship between CC and yield was only significant at 8WAS. By accounting for within- and between-field variations in NOTs and FMF (separately) through linear mixed-effects modeling, predictability of grain yield from UAV-derived VIs was generally (R²≤0.24), however, the inclusion of ground-measured biophysical variable (mainly Ht) improved the explained yield variability (R² ≥0.62, RMSEP≤0.35) in NOTs but not in FMF. We conclude that yield prediction with UAV-acquired imageries (before harvest) is more reliable under controlled experimental conditions (NOTs), than in actual farmer-managed fields where various confounding agronomic factors can amplify noise-signal within the vegetation canopy.

In this work, we show that a late fusion approach to multi-modality in sign language recognition improves the overall ability of the model in comparison to the singular approaches of Computer Vision (88.14%) and Leap Motion data classification (72.73%). With a large synchronous dataset of 18 BSL gestures collected from multiple subjects, two deep neural networks are benchmarked and compared to derive a best topology for each. The Vision model is implemented by a CNN and optimised MLP and the Leap Motion model is implemented by an evolutionary optimised deep MLP topology search. Next, the two best networks are fused for synchronised processing which results in a better overall result (94.44%) since complementary features are learnt in addition to the original task. The hypothesis is further supported by application of the three models to a set of completely unseen data where a multi-modality approach achieves the best results relative to the single sensor method. When transfer learning with the weights trained via BSL, all three models outperform standard random weight distribution when classifying ASL, and the best model overall for ASL classification was the transfer learning multi-modality approach which scored 82.55% accuracy.

Urgent environmental challenges and emerging additive manufacturing (AM) technologies push research towards more performant and new materials. In the field of metallurgy, high entropy alloys (HEAs) have recently represented a topic of intense research because of their promising properties, such as high temperature strength and stability. Moreover, this class of multi-principal element alloys (MPEAs) have opened up researcher community to unexplored compositional spaces, making prosper literature of high-throughput methodologies and tools for rapidly screening large number of alloys. However, none of the methods has been aimed to design new MPEAs for AM process known as selective laser melting (SLM) so far. Here we conducted nanoindentation testing on single scan tracks of elemental powder blends and pre-alloyed powders after ball milling of AlTiCuNb and AlTiVNb. Results show that nanoindentation can represent an effective technique to gain information about phase evolution during laser scanning, contributing to accelerate the development of new MPEAs.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

Abstract: Thermal desalination is yet a reliable technology in the treatment of brackish water and seawater; however, its demanding high energy requirements have lagged it compared to other non-thermal technologies such as reverse osmosis. This review provides an outline of the development and trends of the three most commercially used thermal or phase change technologies worldwide: Multi Effect Distillation (MED), Multi Stage Flash (MSF), and Vapor Compression Distillation (VCD). First, state of water stress suffered by regions with little fresh water availability and existing desalination technologies that could become an alternative solution are shown. The most recent studies published for each commercial thermal technology are presented, focusing on optimizing the desalination process, improving efficiencies, and reducing energy demands. Then, an overview of the use of renewable energy and its potential for integration into both commercial and non-commercial desalination systems is shown. Finally, research trends and their orientation towards hybridization of technologies and use of renewable energies as a relevant alternative to the current problems of brackish water desalination are discussed. This reflective and updated review will help researchers to have a detailed state of the art of the subject and to have a starting point for their research, since current advances and trends on thermal desalination are shown.

Real-world optimization problems are often governed by one or more constraints. Over the last few decades, extensive research has been performed in Constrained Optimization Problems (COPs) fueled by advances in computational intelligence. In particular, Evolutionary Algorithms (EAs) are a preferred tool for practitioners for solving these COPs within practicable time limits. We propose an ensemble of multi- method hybrid EA framework with four mutation operators, two crossover operators, multi-search [Differential Evolution (DE) & Gaining Sharing Knowledge (GSK)] optimization algorithm, and ensemble of constraint handling techniques to solve global real- world constrained optimization problem. The proposed frame- work FEPEA has an ascendancy of multiple adaptation strategies concerning the control parameters, search mechanisms, two sub-populations as well as uses knowledge sharing mechanism between junior and senior phases. The algorithm also combines the power of four popular constraint handling techniques (CHT) and uses a voting mechanism to select any particular CHT. On top of that, this algorithm also uses both linear and non- linear population size reduction in every step of the evolutionary process. We test our method on 57 real-world problems provided as part of the CEC 2020 special session & competition on real- world constrained optimization benchmark suite. Experimental results indicate that FEPEA is able to achieve state-of-the- art performance on real-world constrained global optimization when compared against other well-known real-world constrained optimizers.

The hybrid bond graph has been studied in depth for scalar bond graphs, but how does this translate to the multi-bond graph? Here, the controlled junction – used to model structural switching such as contact – is extended to the multi-bond case. This is a simple process, assuming that all bonds switch simultaneously (which makes physical sense). A controlled 0-junction is applied to multi-bond graph of a car, which can lose contact with the ground in cornering. Dynamic causality features, but this can be accommodated using an equational submodel in 20-Sim (in a manner similar to that used with scalar bond graphs). The junction is proposed for subsequent work to develop a validated multi-body dynamics car model in cornering.

The quality of digital elevation models (DEMs) is inevitably affected by the limitations of the imaging modes and the generation methods. One effective way to solve this problem is to merge the available datasets through data fusion. In this paper, a fusion-based global DEM dataset (82°S-82°N) is introduced, which we refer to as GSDEM-30. This is a 30-m DEM mainly reconstructed from the unfilled SRTM1, AW3D30, and ASTER GDEM v2 datasets combining the multi-source and multi-scale fusion techniques. A comprehensive evaluation of the GSDEM-30 data, as well as the 30-m ASTER GDEM v2 and AW3D30 DEM, was presented. Global ICESat GLAS data and the local National Elevation Dataset (NED) were used as the reference for the vertical accuracy validation, while GlobeLand30 was introduced for the landscape analysis. Furthermore, we employed the maximum slope approach to detect the potential artefacts in the DEMs. The results show that the GDEM data are seriously affected by noise and artefacts. With the advantage of the multiple datasets and the refined post-processing, the GSDEM-30 are contaminated with fewer anomalies than both ASTER GDEM and AW3D30. The fusion techniques used can also be applied to the reconstruction of other fused DEM datasets.

The framework of product life cycle (PLC) cost analysis is one of the most important evaluation tools for a contemporary high-tech company in an increasingly competitive market environment. The PLC-purchasing strategy provides the framework for a procurement plan and examines the sourcing strategy of a firm. The marketing literature emphasizes that ongoing technological change and shortened life cycles are important elements in commercial organizations. From a strategic viewpoint, the vendor has an important position between supplier, buyer and manufacturer. The buyer seeks to procure the products from a set of vendors to take advantage of economies of scale and to exploit opportunities for strategic relationships. However, previous studies have seldom considered vendor selection (VS) based on PLC cost (VSPLCC) analysis. The purpose of this paper is to solve the VSPLCC problems considering the situation of a single-buyer-multiple-supplier. For this issue, a new VSPLCC procurement model and solution procedure are derived by this paper to minimize net cost, rejection rate, late delivery and PLC cost subject to vendor capacities and budget constraints. Moreover, a real case in Taiwan is provided to show how to solve the VSPLCC procurement problem.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

Fragmentation processes of multiply charged ions of C10H8 isomers produced in fast proton collision (velocity between 1.41 and 2.4 a.u.) is discussed in view of their fundamental molecular dynamics. Especially so in the mechanisms to produce a variety of carbon clusters from such ions. This aspect is assessed with the help of a multihit analysis of daughter ions in coincidence with elimination of H+ and CHn+ (n = 0 to 3). The elimination of H+/C+ was found to be very different from CH3+ loss. The loss of CH3+ was found to be accompanied with the formation of heavy ions like C9H5+, C9H5++ and C7H3+ by a cascade of momentum correlated dissociations. The most probable structures of large fragment ions in the CH3+ loss cascade are predicted with the help of computed electronic energy and the multihit ToF correlations of second and third hit. In addition, we report observation of super-dehydrogenation of naphthalene and azulene targets, with evidence of complete dehydrogenation in a single collision.

This paper proposes a multi-terminal adaptive collaborative operation method to solve the problem of unstable internal force tracking in clamping and handling unknown objects by multi-terminal robots. In the proposed method, the internal command force changes the complex internal force control problem into an internal force tracking problem from multi-slave to master. Moreover, we develop an algorithm for multi-slave setups to estimate object stiffness and motion uncertainty in the direction of the internal command force according to Lyapunov theory. Finally, the impedance control generates a reference trajectory for the multi-slave to maintain the desired internal force and track the master’s motion. Several experiments are conducted on a self-made robot equipped. The experimental results show that the oscillation amplitude of each slave end is less than 1 mm, the directional oscillation amplitude is less than 1 degree during the tracking of the desired commanded internal force. For objects with low stiffness, the error of the commanded internal force is less than 1 N (6%) per slave. The error in tracking the commanded internal force for objects with high stiffness is less than 2 N (8%). The results prove the feasibility and effectiveness of the proposed method.

In gravitational theory and astrophysical dynamics, singular initial value problems (IVPs) are frequently encountered. Finding the solutions to this class of IVPs can be challenging due to their complex nature. This study strives to circumvent the complexity by proposing a numerical method for solving such problems. The approach proposed in the current research seeks solutions to the IVP by partitioning the domain [0,L] of the problem into two intervals and solving the problem on each domain. The study seeks a closed-form solution to the IVP in the interval containing the singular point. A linearization technique and piecewise partitioning of the domain not containing the singularity are applied to the nonlinear IVP. The resulting linearized differential equation is solved using the Chebyshev spectral collocation method. Some examples are presented to illustrate the efficiency of the proposed method. Numerical analysis of the solution and residual errors are shown to ascertain convergence and accuracy. The results suggest that the technique gives accurate convergent solutions using a few collocation points.

Dracunculiasis (also known as Guinea worm disease) is caused by Dracunculus medinensis parasite and it spreads by drinking water containing Larvae of Guinea worm. The lack of safe water facilities, preventions and treatments resulted in highly dangerous consequences in its endemic regions. The economy of the affected regions totally falls down due to less production which is the result of agricultural field worker’s bad health. In this study, a multi epitope vaccine was designed against Dracunculus medinensis by using immune-informatics. The vaccine was designed by using T-Cell and B-Cell epitopes derived from Dracunculus medinensis proteins (Lactamase-B domain-containing protein, G-Domain containing protein and Ferrochelatase) in addition to Adjuvants and Linkers. The tertiary structure, physiochemical properties and immunogenic elements of vaccine were achieved. The validation of tertiary structure was accessed, and quality was achieved. In addition, the world coverage of parasite’s CTL and HTL epitopes is 95.61%. The stability of the chimeric vaccine was achieved through disulfide engineering. The molecular docking with Toll Like Receptor 4 (TLR-4) of vaccine showed its binding efficiency followed by Molecular Dynamic Simulation. The immune simulation suggested the mediated cell immunity and repeated antigen clearance. At the end, the optimized codon was used in in silico cloning to ensure vaccine’s higher exposure in bacterium E. coli strain K12. With further assessments, it is believed that the proposed multi epitope vaccine has strong immunogen to control Dracunculus medinensis which may result in better social and economic conditions of endemic regions.

Introduction Tuberculosis is common in Pakistan. Due to various factors including socioeconomic factors, compliance is poor to anti-tuberculosis drugs, leading to resistance. We aim to determine the prevalence of Multidrug resistance (MDR) tuberculosis in Pakistani population.Methods A prospective observational study was conducted from April 1, 2019, to December 31, 2019, in the Pulmonology department of a tertiary care hospital in Pakistan. Culture and sensitivity were assessed using a sputum sample or, in cases of an absent sputum sample, from Broncho alveolar lavage.ResultsApproximately 71.3% percent patients who had tuberculosis were found to be resistant to Isoniazid and around 48.6% did not respond to Rifampin. Multi-drug resistant was found in 29.4% participants.ConclusionMulti-drug resistance tuberculosis is very prevalent in Pakistan, which may increase burden on health care system and may lead to various complications of tuberculosis.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

In the framework of maritime surveillance, vessel detection techniques based on spaceborne Synthetic Aperture Radar (SAR) images have promoted extensive applications for the effective understanding of unlawful activities at sea. The paper deal with this topic presenting a novel approach exploiting a cascade application of a pre-screening, and discrimination phase. The latter leverage the SAR spectrum by means of sub-looks analysis. For the first time, the method has been validated with experiments on multi-frequency (C-, X-, and L-band) SAR images. For a future syngergic exploitation of more SAR missions, the developed dataset, composed of Sentinel-1, SAOCOM and COSMO-SkyMed images, is comprehensive of multiple images gathered over the same area with short time lag (below 15 minutes). Finally, the diversified processing chains and the results for each mission product and scenarios are discussed. Being the first dataset of SLC (Single Look Complex) SAR multi-frequency data, the present work intends to encourage additional research in this promising field of research.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

In this article, we introduce some multi-messenger studies of blazars. Main contents contain the following parts, 1. the subclasses of blazars and the observational characteristics, 2. emission variabilities from the multi-messenger observations, 3. the physical origin for the multi-messenger studies. Based on mid-IR observations collected from the $WISE$ database, we collect two sources (BZQ J1700+6830 and BZQ J1842+6809) to analyze the mid-IR variabilities. \\ (1) For BZQ J1700+6830, the period is $P\approx$ 42 hr at the four bands ($W1$, $W2$, $W3$, $W4$); for BZQ J1842+6809, the period is $P\approx$ 123 hr at the two bands ($W1$, $W2$). \\ (2) Using the periodicities, we calculate that the central black hole mass ($BH$) should be $M = (5.44\sim33.0)\times10^8M_{\odot}$ for BZQ J1700+6830 and $M = (1.13\sim6.88)\times10^9M_{\odot}$ for BZQ J1842+6809.\\ (3) For the two sources, during the flaring stage, we find anti-clockwise variation trends based on the time-based relations built by the spectral indices ($\alpha$) and flux densities ($F$).\\ (4) We calculate the Doppler factor ($\delta$) when the sources are in the dimming or brightening stages, and find that with the frequency increasing, the Doppler factor become stronger.

The paper considers new effects of the nanoscale state of matter, which open up prospects for the creation of electronic devices using new physical principles. The contact of chemically homogeneous different sizes hydrated nanoparticles of yttrium-stabilized zirconium oxide (ZrO2 – x %mol Y2O3, x=0, 3, 4, 8; YSZ) with particle sizes of 7.5 nm and 7,5 nm; 7.5 nm and 9 nm; 7.5 nm and 11 nm; 7.5 nm and 14 nm in the form of compacts obtained using high hydrostatic pressure (HP-compacts of 300MPa) was studied at direct and alternating current. A unique size effect of the nonlinear (semiconductor) dependence of the electrical properties (in the region U <2.5 V, I ≤ 2.7 mA) of the contact of different-sized YSZ nanoparticles of the same chemical composition is revealed, which indicates the possibility of creating semiconductor structures of a new type based on chemically homogeneous nanostructured systems. The electronic structure of the near-surface regions of nanoparticles of a special type of oxide materials and the possibility, on this basis, to obtain specifically rectifying properties of the contacts were studied theoretically. Models of surface states of the Tamm type are constructed, but considering the Coulomb long-range action. The discovered variance and its dependence on the curvature of the surface of nanoparticles made it possible to study the conditions for the formation of a contact potential difference in cases of nanoparticles of the same radius (synergistic effect), different radii (doped and undoped variants), as well as to discover the possibility of describing a group of powder particles from material within the Anderson model. The established effect makes it possible to solve the problem of diffusion instability of semiconductor heterojunctions and opens up prospects for creating electronics devices with a fundamentally new level of properties for use in various fields of the national economy and breakthrough critical technologies.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

Our work uses Iterative Boltzmann Inversion (IBI) to study the coarse-grained interaction between 20 amino acids and the representative carbon nanotube CNT55L3. IBI is a multi-scale simulation method that has attracted the attention of many researchers in recent years. It can effectively modify the coarse-grained model derived from the Potential of Mean Force (PMF). IBI is based on the distribution result obtained by All-Atom molecular dynamics simulation, that is, the target distribution function, the PMF potential energy is extracted, and then the initial potential energy extracted by the PMF is used to perform simulation iterations using IBI. Our research results have gone through more than 100 iterations, and finally, the distribution obtained by coarse-grained molecular simulation (CGMD) can effectively overlap with the results of all-atom molecular dynamics simulation (AAMD). In addition, our work lays the foundation for the study of force fields for the simulation of the coarse-graining of super-large proteins and other important nanoparticles.

Multi-morbidity and polypharmacy are common in older people and pose a challenge for health and social care systems especially in context of global population ageing. They are complex and interrelated concepts in the care of older people that require early detection and patient centred decision making that are underpinned by the principles of multidisciplinary led comprehensive geriatric assessment (CGA). Personalised care plans need to remain responsive and adaptable to the needs of a patient, enabling an individual to maintain their independence.

This paper presents a new and enhanced fusion module for the Multi-Sensor Precipitation Estimator (MPE) that would objectively blend real-time satellite quantitative precipitation estimates (SQPE) with radar and gauge estimates. This module consists of a preprocessor that mitigates systematic bias in SQPE, and a two-way blending routine that statistically fuses adjusted SQPE with radar estimates. The preprocessor not only corrects systematic bias in SQPE, but also improves the spatial distribution of precipitation based on SQPE and makes it closely resemble that of radar-based observations. It uses a more sophisticated radar-satellite merging technique to blend preprocessed datasets, and provides a better overall QPE product. The performance of the new satellite-radar-gauge blending module is assessed using independent rain gauge data over a 5-year period between 2003-2007, and the assessment evaluates the accuracy of newly developed satellite-radar-gauge (SRG) blended products versus that of radar-gauge products (which represents MPE algorithm currently used in the NWS operations) over two regions: I) inside radar effective coverage and II) immediately outside radar coverage. The outcomes of the evaluation indicate a) ingest of SQPE over areas within effective radar coverage improve the quality of QPE by mitigating the errors in radar estimates in region I; and b) blending of radar, gauge, and satellite estimates over region II leads to reduction of errors relative to bias-corrected SQPE. In addition, the new module alleviates the discontinuities along the boundaries of radar effective coverage otherwise seen when SQPE is used directly to fill the areas outside of effective radar coverage.

Bioelectrocatalysis provides the intrinsic catalytic-functions of redox enzymes to non-specific electrode reactions and is the most important and basic concept for biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multi-analyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination.

This article proposes the use of a multi-scale and multi-sensor approach to collect and modelling 3D data concerning wide and complex areas in order to obtain a variety of metric information in the same 3D archive, based on a single coordinate system. The employment of these 3D georeferenced products is multifaceted and the fusion or integration among different sensors data, scales and resolutions is promising and could be useful for the generation of a model that could be defined as hybrid. The correct geometry, accuracy, radiometry and weight of the data models are hereby evaluated comparing integrated processes and results from Terrestrial Laser Scanner (TLS), Mobile Mapping System (MMS), Unmanned Aerial Vehicle (UAV), terrestrial photogrammetry, using Total Station (TS) and Global Navigation Satellite System (GNSS) as topographic survey. The entire analysis underlines the potentiality of the integration and fusion of different solutions and is a crucial part of the “Torino 1911” project whose main purpose is mapping and virtually reconstructing the 1911 Great Exhibition settled in the Valentino Park in Turin (Italy).

Does cell clustering influence intrinsic and acquired multi-drug resistance (MDR) differently? To address this question, we studied cultured monolayers (representing individual cells) and cultured spheroids (representing clusters) formed by drug-naïve (intrinsic MDR) and drug-exposed (acquired MDR) lines of ovarian cancer A2780 cells by cytometry of reaction rate constant (CRRC). MDR efflux was characterized by accurate and robust “cell number vs. MDR efflux rate constant (kMDR)” histograms. Both drug-naïve and drug-exposed monolayer cells presented unimodal histograms; the histogram of drug-exposed cells was shifted towards higher kMDR value suggesting greater MDR activity. Spheroids of drug-naïve cells presented a bimodal histogram indicating the presence of two subpopulations with different MDR activity. In contrast, spheroids of drug-exposed cells presented a unimodal histogram qualitatively similar to that of the monolayers of drug-exposed cells but with a moderate shift towards greater MDR activity. The observed greater effect of cell clustering on intrinsic than on acquired MDR can help guide the development of new therapeutic strategies targeting clusters of circulating tumor cells.

In this paper, we consider a new class of polynomials which is called the multi-poly-Euler polynomials. Then, we investigate their some properties and relations. We provide that the type 2 degenerate multi-poly-Euler polynomials equals a linear combination of the degenerate Euler polynomials of higher order and the degenerate Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Euler polynomials and degenerate Whitney numbers.

Inspired by the definition of degenerate multi-poly-Genocchi polynomials given by using the degenerate multi-polyexponential functions. In this paper, we consider a class of new generating function for the degenerate multi-poly-Bernoulli polynomials, called the type 2 degenerate multi-poly-Bernoulli polynomials by means of the degenerate multiple polyexponential functions. Then, we investigate their some properties and relations. We show that the type 2 degenerate multi-poly-Bernoulli polynomials equals a linear combination of the weighted degenerate Bernoulli polynomials and Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Bernoulli numbers and degenerate Whitney numbers.

A multi-decadal change analysis of the irrigation ponds in Taoyuan, Taiwan was conducted by using multi-source data including digitized ancient maps, declassified single-band CORONA satellite images, and multispectral SPOT images. Supervised LULC classifications were conducted using four textural features derived from the single-band CORONA images and spectral features derived from SPOT images. Post-classification analysis revealed that the number of irrigation ponds in the study area decreased during the post-World War II farmland consolidation period (1945 – 1965) and the subsequent industrialization period (1970 – 2000). However, efforts on restoration of irrigation ponds in recent years have resulted in gradual increases in the number (9%) and total area (12%) of irrigation ponds in the study area.

In this review, we will cover a general overview of the current panorama on lncRNAs with an actual or potential role as biological markers in cancer. We will discuss examples of multi-omics approaches that integrates information on somatic aberrations, gene expression and epigenomics, with the scope of providing a more comprehensive view of the functional impact of lncRNA profiles and how these paradigm can be exploited for the discovery and selection of lncRNAs with a functional role and their use as variables informing on progression and prognostic and help guiding the selection of therapeutic strategies for cancers. Finally, we propose a perspective for future evolution of the study of lncRNAs and the discovery of their functional and harnessing their potential to assist in clinical management of malignancies.

Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.

In this work, we propose a self-supervised multi-agent system that meets the online learning of clustering tasks for video behavior recognition spatio-temporal tasks. Encoding visual behavioral actions as discrete temporal sequence(DTS). Real-time clustering recognition task in a multi-agent system for continuous model building, training, and correction. Finally, we implemented a fully decentralized multi-agent system and completed its feasibility verification in a surveillance video application scenario on vehicle path clustering.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

The giant challenge breeding flood-irrigated rice is to identify superior genotypes that present high-yielding with specific grain qualities, resistance to abiotic and biotic stresses, excellent adaptation to the target environment. Thus, the objectives of this study were to propose a bayesian multi-trait model, estimate genetic parameters, and select flood-irrigated rice genotypes with better genetic potentials in different evaluation environments. For this, twenty-five rice genotypes belonging to the flood-irrigated rice improvement program were evaluated. The grain yields, grain length, width and thickness, grain length, and grain width and weight of 100 grains in the agricultural year 2016/2017. The experimental design used in all experiments was a randomized block design with three replications. The Monte Carlo Markov Chain algorithm estimated genetic parameters and genetic values. The grain thickness trait was considered highly heritable, with a credibility interval ranging from: h^2: 0.9480; 0.9440; 0.8610, in environments 1, 2, and 3, respectively. The grain yields showed a low correlation estimate between grain thickness and 100-grain weight, in all environments, with a credibility interval ranging from (ρ= 0.5477; 0.5762; 0.5618 and 0.5973; 0.5247; 0.5632, grain thickness and 100-grain weight, in environments 1, 2, and 3, respectively). The Bayesian multi-trait model proved to be an adequate strategy for the genetic improvement of flood-irrigated. Genotypes 2 and 15 had similar potential in the three environments, they should be selected as high-performance multi-trait genotypes for the genetic breeding of flood-irrigated rice in the program.

Multi-objective optimization (MOO) is an optimization involving minimization or maximization of several objective functions more than the conventional one objective optimization, which is useful in many fields. Many of the current methodologies addresses challenges and solutions that attempt to solve simultaneously several Objectives with multiple constraints subjoined to each. Often MOO are generally subjected to linear inequality, equality and or bounded constraint that prevent all objectives from being optimized at once. This paper reviews some recent articles in area of MOO and presents deep analysis of Random and Uniform Entry-Exit time of objectives. It further break down process into sub-process and then provide some new concepts for solving problems in MOO, which comes due to periodical objectives that do not stay for the entire duration of process lifetime, unlike permanent objectives which are optimized once for the entire process duration. A methodology based on partial optimization that optimizes each objective iteratively and weight convergence method that optimizes sub-group of objectives are given. Furthermore, another method is introduced which involve objective classification, ranking, estimation and prediction where objectives are classified based on their properties, and ranked using a given criteria and in addition estimated for an optimal weight point (pareto optimal point) if it certifies a coveted optimal weight point. Then finally predicted to find how far it deviates from the estimated optimal weight point. A Sample Mathematical Tri-Objectives and Real world Optimization was analyzed using partial method, ranking and classification method, the result showed that an objective can be added or removed without affecting previous or existing optimal solutions. Therefore suitable for handling time governed MOO. Although this paper presents concepts work only, it’s practical application are beyond the scope of this paper, however base on analysis and examples presented, the concept is worthy of igniting further research and application.

This paper addresses a wildlife monitoring problem using a team of UAVs for efficient monitoring of wildlife. The state-of-the-art technology using UAVs has been an increasingly popular tool to monitor wildlife compared to the traditional methods such as satellite imagery-based sensing or GPS trackers. However, there still exist unsolved problems as to how the UAVs need to cover a spacious domain to detect animals as many as possible. In this paper, we propose the optimal transport-based wildlife monitoring strategy for a multi-UAV system, to prioritize monitoring areas while incorporating complementary information such as GPS trackers and satellite-based sensing. Through the proposed scheme, the UAVs can explore the large-size domain effectively and collaboratively with a given priority. The time-varying nature of wildlife due to their movements is modeled as a stochastic process, which is included in the proposed work to reflect the spatio-temporal evolution of their position estimation. In this way, the proposed monitoring plan can lead to efficient wildlife monitoring with a high detection rate. Various simulation results including statistical data are provided to validate the proposed work.

Metabolomics deals with multiple and complex chemical reactions within living organisms and how these are influenced by external or internal perturbations. It lies at the heart of omics profiling technologies not only as the underlying biochemical layer that reflects information expressed by the genome, the transcriptome and the proteome, but also as the closest layer to the phenome. The combination of metabolomics data with the information available from genomics, transcriptomics, and proteomics offers unprecedented possibilities to enhance current understanding of biological functions, elucidate their underlying mechanisms and uncover hidden associations between omics variables. As a result, a vast array of computational tools have been developed to assist with integrative analysis of metabolomics data with different omics. Here, we review and propose five criteria – hypothesis, data types, strategies, study design and study focus – to classify statistical multi-omics data integration approaches into state-of-the-art classes under which all existing statistical methods fall. The purpose of this review is to look at various aspects that lead the choice of the statistical integrative analysis pipeline in terms of the different classes. We will draw a particular attention to metabolomics and genomics data to assist those new to this field in the choice of the integrative analysis pipeline.

The increasing number of robots around us will soon create a demand for connecting these robots in order to achieve goal-driven teamwork in heterogeneous multi-robot systems. In this paper, we focus on robot teamwork specifically in dynamic environments. While the conceptual modeling of multi-agent teamwork has been studied extensively during the last two decades, related engineering concerns have not received the same degree of attention. Therefore, this paper makes two contributions. The analysis part discusses general design challenges that apply to robot teamwork in dynamic application domains. The constructive part presents a review of existing engineering approaches for challenges that arise with dynamically changing runtime conditions. An exhaustive survey of robot teamwork aspects would be beyond the scope of this paper. Instead, we aim at creating awareness for the manifold dimensions of the design space and highlight state-of-the-art technical solutions for dynamically adaptive teamwork, thus pointing at open research questions that need to be tackled in future work.

From ancient time, electric grid system developed as one way direction in which users get the electricity from generators to far end. However, it is not the consumer centric as its one way process and consumer have no way to communicate to the server. Thus, with the development of digital revolution, the grid converted to smart grid and meter converted to smart meter. In smart grid, the protocol follows the bidirectional way of communication with support of consumers in the system. Recently in 2016, Jo et al. proposed the scheme for smart grid system using privacy preserving model and claimed to be efficient and secure. However, in this paper we have analyzed the scheme of Jo et al. and proved that the scheme is vulnerable to Replay attack and afterwards shows the change in protocol to withstand against this attack.

Equality and incomparability multi-label ranking have not been introduced to learning before. This paper proposes new native ranker neural network to address the problem of multi-label ranking including incomparable preference orders using a new activation and error functions and new architecture. Preference Neural Network PNN solves the multi-label ranking problem, where labels may have indifference preference orders or subgroups which are equally ranked. PNN is a nondeep, multiple-value neuron, single middle layer and one or more output layers network. PNN uses a novel positive smooth staircase (PSS) or smooth staircase (SS) activation function and represents preference orders and Spearman ranking correlation as objective functions. It is introduced in two types, Type A is traditional NN architecture and Type B uses expanding architecture by introducing new type of hidden neuron has multiple activation function in middle layer and duplicated output layers to reinforce the ranking by increasing the number of weights. PNN accepts single data instance as inputs and output neurons represent the number of labels and output value represents the preference value. PNN is evaluated using a new preference mining data set that contains repeated label values which have not experimented on before. SS and PS speed-up the learning and PNN outperforms five previously proposed methods for strict label ranking in terms of accurate results with high computational efficiency.

The concept of transit-oriented development (TOD) has been widely recognized in recent years for its role in reducing car traffic, improving public transportation, and enhancing traffic sustainability. This paper conducts empirical research on a developed rail transit network, using Shanghai as a case study. In addition to traditional TOD features, other factors based on urban rail transit are introduced, including multi-level modeling (MLM), which is used to analyze the possible factors influencing rail patronage. To avoid the bias of research results led by the correlation between independent variables, factors are divided into two levels. The first level includes three groups of variables: the built environment, station characteristics, and socioeconomic and demographic characteristics. The second level includes a set of variables which are regional characteristics. Results show that the most significant impact on train patronage is station location in the business district area. Other factors that have a positive effect on promoting rail transit travel include the number of service facilities around the station, degree of employment around the station, economic level, intensity of residential development, if the station is a transfer station, the operating period of the station, and the size of the large transportation hub around the station.

We propose a probabilistic graphical model for discriminative substrate characterization, to support geological and biological habitat mapping in aquatic environments. The model, called a fully connected conditional random field (CRF), is demonstrated using multispectral and monospectral acoustic backscatter from heterogeneous seafloors in Patricia Bay, British Columbia, and Bedford Basin, Nova Scotia. Unlike previously proposed discriminative machine learning algorithms, the CRF model considers both the relative backscatter magnitudes of different substrates and their relative proximities. The model therefore combines the statistical flexibility of a machine learning algorithm with an inherently spatial treatment of the substrate. The CRF model predicts substrates such that nearby locations with similar backscattering characteristics are likely to be in the same substrate class. The degree of proximity and allowable backscatter similarity are controlled by parameters that are learned from the data. CRF model results were evaluated against a popular generative model known as a Gaussian Mixture model that doesn't include spatial dependencies, only covariance between substrate backscattering response over different frequencies. Both models are used in conjunction with sparse bed observations/samples in a supervised classification. A detailed accuracy assessment, including a leave-one-out cross-validation analysis, was performed using both models. Using multispectral backscatter, the GMM model trained on 50% of the bed observations resulted in a 75% and 89% average accuracies in Patricia Bay and Bedford Basin, respectively. The same metrics for the CRF model were 78% and 95%. Further, the CRF model resulted in a 91% mean cross-validation accuracy across four substrate classes at Patricia Bay, and a 99.5% mean accuracy across three substrate classes at Bedford Basin, which suggest that the CRF model generalizes extremely well to new data. This analysis also showed that the CRF model was much less sensitive to the specific number and locations of bed observations than the generative model, owing to its ability to incorporate spatial autocorrelation in substrates. The CRF approach therefore may prove to be a powerful `spatially aware' alternative to other discriminative classifiers.

Aiming at the problems that are poor generalization performance, low retrieval accuracy and large time consumption of existing content-based image retrieval system, the hierarchical image retrieval method based on multi feature fusion is proposed in this paper. The retrieval accuracy rates on Corel5K, UKbeach and Holidays are 68.23(Top 1), 3.73(N-S) and 88.20(mAp), respectively. The experimental results show that the method proposed in this paper can effectively improve the deficiency of single feature retrieval and save time significantly in the premise of a small amount of loss of accuracy.

The variations of visibility, PM mass concentration and mixing layer height (MLH) at four major urban-industry regions (Shenyang, Anshan, Benxi and Fushun) in multi-cities of central Liaoning over northeast China were evaluated from 2009-2012 to characterize the dynamics effect on air pollution. The annual mean visibilities were about 13.7±7.8km, 13.5±6.5km, 12.8±6.1km and 11.5±6.8km in Shenyang, Anshan, Benxi and Fushun, respectively. The pollution load (PM×MLH) shown a weaker vertical diffusion in Anshan with a higher PM concentration in the near-surface. High concentrations of fine mode particles may be partially attributed to the biomass burning emissions from September in Liaoning Province and surrounding regions in Northeast China as well as the coal burning during the heating period with lower MLH in winter. The increasing wind speed has a similar change as the increasing of mixing layer height to make the effect on the aerosol vertical diffusion. The visibility on the non haze-fog days was about 2.5-3.0 times higher than that on hazy and fog days. The fine particle concentrations of PM2.5 and PM1.0 on the haze and fog days were ~1.8-1.9 times and ~1.5 times higher than that on no hazy-fog days. The MLH during fog pollution showed more declining trend than haze pollution compared with non haze-fog days. The results of this study could provide the useful information to better recognize the effects of vertical pollutants diffusion on air quality in the multi-cities of central Liaoning over Northeast China.

Multi-microgrid has many new characteristics, such as bi-directional power flows, flexible operation modes and variable fault currents with different control strategy of inverter interfaced distributed generations (IIDGs). All these featuring aspects pose challenges to multi-microgrid protection. In this paper, current and voltage characteristics of different feeders are analyzed when fault occurs in different positions of multi-microgrid. Based on the voltage and current distribution characteristics of the line parameters, a new protection scheme for the internal fault of multi-microgrid is proposed, which takes the change of phase difference and amplitude of measured bus admittance as the criterion. This scheme with high sensitivity and reliability, has a simple principle and is easy to be adjusted. PSCAD/EMTDC is used in simulation analysis, and simulation results have verified the correctness and effectiveness of the protection scheme.

Based on the definition of double fuzzy relations, two types of new rough set models are constructed, which are multi-granulation double fuzzy rough sets called optimistic and pessimistic multi-granulation double fuzzy rough sets, and some of their properties were studied. In addition, we study the relationship between optimistic and pessimistic multi-granulation double fuzzy rough sets and double fuzzy rough sets.

As the core components of water jet propulsion system, water jet pump, directly affect the ship's propulsion performance. 3D reverse design method can effectively suppress the impeller secondary flow to get better performing hydraulic models. Aiming at fast and efficient optimization of the impellers, we parameterize the impellers and runner, and coupled with optimization algorithms and numerical calculations. It is an efficient and feasible way to coupling optimization based on multi-parameter, multi-objective and optimization algorithms, and parameterizing the impellers and guide vane geometry based on the 3D model designed by 3D reverse design method. In this paper, the waterjet propulsion pump is taken as the research object. According to the design method of the waterjet propulsion pump hydraulic model, the traditional axial flow blade design method, the modern ternary design theory of the blades, and the parametric three-dimensional reverse design method are selected to constructing an optimal design optimization strategy for the impeller of water-jet propulsion pump based on multi-parameter and multi-object genetic algorithm. Under the design conditions, the optimized pump efficiency reaches 89.28%, which is 1.24% higher than the original hydraulic model. The optimized pump head is 13.51 m, which is 0.39m more than the original hydraulic model. Under the design condition, the test measured head is 13.26m, the numerical calculation result is 1.88% higher than the test result, the test measured efficiency is 87.1%, the numerical calculation result is 2.5% higher than the test result. From the test results, the optimized impeller has higher hydraulic performance. Experiments have shown that it is feasible to optimize the design strategy.

Traditional soil characterization methods are time consuming, laborious and invasive and do not allow long-term repeatability of measurements. The overall aim of this paper was to assess and model spatial variability of the soil in an olive grove in south Italy by using data from two sensors of different type: a multi-spectral on-board drone radiometer and a hyperspectral visible-near infrared-shortwave infrared (VIS-NIR-SWIR) reflectance radiometer as well as sample data, to arrive at a delineation of homogeneous areas. The hyperspectral data were processed using continuum removal methodology to obtain information about the content and composition of clay. Differently, the multispectral data were firstly upscaled to the support of soil data using geostatistics and taking into account change of support. Secondly, the two-sensor data were integrated with soil granulometric properties by using the multivariate geostatistical techniques of multi-collocated cokriging and factor cokriging, in order to achieve a more exhaustive and finer-scale soil characterisation. The paper shows the impact of change of support on the uncertainty of soil prediction that can have a significant effect on decision making in Precision Agriculture. Moreover, four regionalised factors at two different scales (two per each scale) were retained and mapped. Each factor provided a different delineation of the field with areas characterised by different granulometry and clay composition. The applied method is sufficiently flexible and could be applied to any number and type of sensors.

Plant geneticists and breeders have used marker technology since the 1980s in quantitative trait locus (QTL) identification. Marker-assisted selection is effective for large-effect QTL but has been challenging to use with quantitative traits controlled by multiple minor effect alleles. Therefore, genomic selection (GS) was proposed to estimate all markers simultaneously, thereby capturing all their effects. However, breeding programs are still struggling to identify the best strategy to implement it into their programs. Traditional breeding programs need to be optimized to implement GS effectively. This review explores the optimization of breeding programs for variety release based on aspects of the breeder’s equation. Optimizations include reorganizing field designs, training populations, increasing the number of lines evaluated, and leveraging the large amount of genomic and phenotypic data collected across different growing seasons and environments to increase heritability estimates, selection intensity, and selection accuracy. Breeding programs can leverage their phenotypic and genotypic data to maximize genetic gain and selection accuracy through GS methods utilizing multi-trait and, multi-environment models, high-throughput phenotyping, and deep learning approaches. Overall, this review describes various methods that plant breeders can utilize to increase genetic gains and effectively implement GS in breeding .

Many complex behaviours in biological systems emerge from large populations of interacting molecules or cells, generating functions that go beyond the capabilities of the individual parts. Such collective phenomena are of great interest to bioengineers due to their robustness and scalability. However, engineering emergent collective functions is difficult because they arise as a consequence of complex multi-level feedback, which often spans multiple length-scales. Here, we present a perspective on how some of these challenges could be overcome by using multi-agent modelling as a design framework within synthetic biology. Using case studies covering the construction of synthetic ecologies to biological computation and synthetic cellularity, we show how multi-agent modelling can capture the core features of complex multi-scale systems and provide novel insights into the underlying mechanisms which guide emergent functionalities across scales. The ability to unravel design rules underpinning these behaviours offers a means to take synthetic biology beyond single molecules or cells and towards the creation of systems with functions that can only emerge from collectives at multiple scales.

Chromatographic separation is a critical technique in the manufacturing processes of both chemical products and biopharmaceuticals. Its principle relies on exploiting the differences in distribution between the stationary and mobile phases to achieve the separation of mixtures. The precision of substance concentration during separation directly impacts the quality and usability of the final product. Therefore, the development of an effective and precise separation control technique has long been a vital concern in the field of chromatographic separation control. Currently, the employment of Simulated Moving Bed (SMB) technology for chromatographic separation, which allows for continuous feed, has been recognized as a cutting-edge technique. SMB is a continuous process technology that enhances the efficiency of adsorbents within the bed. This sequential multi-column SMB technology not only increases production capacity but also reduces the consumption of solvents and water. It is acknowledged as one of the cleanest manufacturing technologies in the biopharmaceutical industry. However, multi-column SMB involves various variables such as flow rates in multiple sections and valve switching times, rendering its system control highly complex. Unlike traditional control objectives that aim to minimize control output errors, the control objective of SMB is to achieve a specific proportion of substance concentration. Consequently, designing and implementing traditional control theories for SMB is challenging, leading to SMB systems largely being controlled based on simple PLC controls. Moreover, these controls are often applicable only to single or a few-column SMB setups, limiting the effectiveness of high-capacity applications. To achieve effective control of SMB, this study employs an adjustable intelligent fuzzy controller with a structure like an approximate neural network (NN) for SMB control research. Simulation results demonstrate that the intelligent controller effectively achieves desirable control outcomes for the SMB system.

This work tackles the problem of image restoration, a crucial task in many fields of applied sciences, focusing on removing degradation caused by blur and noise during the acquisition process. Drawing inspiration from the multi-penalty approach based on the Uniform Penalty principle introduced in [Bortolotti et al. arXiv.math.NA/2309.14163], we develop here a new image restoration model and an iterative algorithm for its effective solution. The model incorporates pixel-wise regularization terms and establishes a rule for parameters selection, aiming to restore images through the solution of a sequence of constrained optimization problems. To achieve this, we present a modified version of the Newton Projection method, adapted to multi-penalty scenarios, and prove its convergence. Numerical experiments demonstrate the efficacy of the method in eliminating noise and blur while preserving the image edges.

Machine learning offers advanced tools for efficient management of radio resources in modern wireless networks. In this study, we leverage a multi-agent deep reinforcement learning (DRL) approach, specifically the Parameterized Deep Q-Network (DQN), to address the challenging problem of power allocation and user association in massive multiple-input multiple-output (M-MIMO) communication networks. Our approach tackles a multi-objective optimization problem aiming to maximize network utility while meeting stringent quality of service requirements in M-MIMO networks. To address the non-convex and nonlinear nature of this problem, we introduce a novel multi-agent DQN framework. This framework defines a large action space, state space, and reward functions, enabling us to learn a near-optimal policy. Simulation results demonstrate the superiority of our Parameterized Deep DQN (PD-DQN) approach when compared to traditional DQN and RL methods. Specifically, we show that our approach outperforms traditional DQN methods in terms of convergence speed and final performance. Additionally, our approach shows 72.2 % and 108.5 % improvement over DQN methods and RL method respectively in handling large-scale multi-agent problems in M-MIMO networks.

This study proposes a method for image matching between infrared(IR)-RGB images using a deep learning network to estimate the deformation field. We propose a deformation field generator (DFG) that estimates the deformation field of the transformation matrix to match each pixel or IR image to the RGB image. DFG is a network that receives IR and RGB images as input; the output size is two channels and has the sample resolution as the input image. By warping the IR image through a grid-sampler that warps the image according to the value of the deformation field, we can obtain a warped IR image that matches the RGB image. Additionally, to check whether the warped IR image matched the RGB image, the masking images detecting the segmentation of objects were photographed in two images. Without directly comparing IR and RGB images, we proposed mask loss that warps the IR mask image through the deformation field and grid sampler and then compares the warped IR mask image with the RGB mask image. Mask loss solves the spatial similarity comparison problem with multi-modality images, such as IR and RGB images, by comparing the mask image with the same modality image as the mask image.

This paper proposes a position recognition method for the receiver coil by the secondary coil current. Based on the practical value of the current of the receiver coil, the position recognition of the receiver coil in the WPT system is realized. This paper proposes a 3×3 array multi-transmitter coil grouping and control logic. The mathematical model of mutual inductance between the receiver and transmitter coil at different positions on the X-Y plane is established. A method for identifying the position of the receiver coil according to the current of the receiver coil is proposed. Compared with the traditional position recognition method of the receiver coil, this method does not need to add a detection coil and position sensor and can realize the position recognition of the receiver coil on the 2D plane.

With a high proportion of distributed photovoltaic and lower fossil energy integrated into the distribution network, it is very difficult to ensure the reliability of power supply. The distributed photovoltaic planning model based on big data is proposed. According to the impact stochastic photovoltaics and loads on reliability planning, the static and dynamic capacity-load ratios are proposed. The big data analysis model of distributed photovoltaic planning is established. The big data multi-scenario generation and reduction algorithm of stochastic distributed photovoltaic and load planning is studied, and a source-load big data scenario matching model is proposed. Ac-cording to the source load big data scenario, the dynamic capacity-load ratio of the distribution network is obtained. The static capacity-load ratio calculation method in distribution network planning is studied to ensure the reliability of power supply. Finally, the IEEE 33-bus system is used as an example. The results show that distributed photovoltaic planning based on big data and multi-scenario methods can improve photovoltaic utilization and power supply reliability.

Reading is a complex cognitive task involving processes from different systems. The present work aims to identify some points of divergence reported in the reading literature and discuss them in a new experimental paradigm framework. Inspired by the paradigms of perceptual identification and rapid parallel presentation (RPVP), we emphasize that the originality of our experimental paradigm lies in the recruitment of multi-stable Arabic percepts within the region where low-level processing occurs (i.e., the visual span area). With good flexibility, the current paradigm has reached higher-order processing levels. In agreement with previous works highlighting the parafoveal-on-foveal effect, results suggest parallel word processing. Furthermore, they suggest a rapid extraction of syntactic and semantic information from words in sentences while attributing an advantage to semantic processing in the emergence of the sentence superiority effect.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

Buildings are responsible for approximately 40% of the world’s energy consumption and 36% of the total carbon dioxide emissions. Building occupancy is essential, enabling Occupant-Centric Control for zero emissions and decarbonization. Although existing machine learning and deep learning methods for building occupancy prediction have achieved remarked progress, their analyses remain limited when applied to complex real-world scenarios. Besides, there is a high expectation for Transformer algorithms to predict building occupancy accurately. Therefore, this paper presents an Occupancy Prediction Transformer network (OPTnet). We fuse and feed multi-sensor data (building occupancy, indoor environmental conditions, HVAC operations) into a Transformer model to forecast the future occupancy presence in multiple zones. We perform experimental analysis and compare it to different occupancy prediction methods (e.g., Decision Tree, Long Short-Term Memory networks, Multi-layer perceptron) and diverse time horizons (1,2,3,5,10,20,30mins). The performance metrics (e.g., Accuracy and Mean Squared Error) are employed to evaluate the effectiveness of prediction algorithms. Our OPTnet method achieves superior performance on our experimental two-week data compared to existing methods. The improved performance signifies its potential to enhance HVAC control systems and energy optimization strategies. We will make the code publicly available at https://github.com/kailaisun/occupancy-prediction-binary to promote transparency and reproducibility.

Buckground: Although ceftazidime/avibactam (CAZ/AVI) has become important option for treating adults and children, no recommendations exist for neonates. We report a neonatal sepsis case due to CAZ/AVI-resistant KPC-2 producing-Klebsiella pneumoniae carrying blaVEB-25 and the use of a customized active surveillance program in conjunction to infection control measures. Methods: The index case was an extremely premature neonate hospitalized for 110 days that had been previously treated with multiple antibiotics. Customized molecular surveillance was implemented at hospital level and enhanced infection control measures were taken for early recognition and prevention of outbreak. Detection and identification of blaVEB-25 was performed by next-generation sequencing. Results: That was the first case of a bloodstream infection caused by KPC producing K. pneumoniae that was resistant to CAZ/AVI without the presence of a metalo-β-lactamase in the multiplex PCR platform in a neonate. All 36 additional patients tested (12 in the same NICU and 24 from other hospital departments) carried wild-type blaVEB-1 but they did not harbor blaVEB-25. Conclusion: The emergence of VEB-25 is signal for horizontal transfer of plasmids at hospital facilities and it is of greatest concern for maintaining a sharp vigilance for surveillance of novel resistance mechanisms. Molecular diagnostics can guide appropriate antimicrobial therapy and early implementation of infection control measures against antimicrobial resistance.

Current effort with light field displays is mainly concentrated on the widest possible viewing angle, while a single viewer only needs to view the display in a specific viewing direction. To make light field display a practical practice, a super multi-view light field display is proposed to compress the information in the viewing zone of a single user by reducing the redundant viewpoints. A quasi-directional backlight is proposed and a lenticular lens array is applied to achieve the restricted viewing zone. Eye-tracking technique is applied to extend the viewing area. Experimental results show that the proposed scheme can present vivid 3D scene with smooth motion parallax. Only 16.7% conventional light field display data are required to achieve 3D display. Furthermore, an illumination power of 3.5 watt is sufficient to lighten a 31.5-inch light field display，which takes up 1.5% of the illumination power required for planar display of similar configuration.

In this paper, we extend the Merton model of investment in discrete time to the cases when there is a finite number of investors and the market is with frictions represented by convex penalty functions defined for each investor. In the main result of this paper, we proved the existence of optimal strategy of investment by using a new approach based on the formulation of an equivalent general equilibrium economy model.

For the ground-state properties of gas-phase nanomolecules with multi-reference character, thermally-assisted-occupation density functional theory (TAO-DFT) has been recently found to outperform the widely used Kohn-Sham density functional theory, when the conventional exchange-correlation energy functionals are employed. Aiming to explore solvation effects on the ground-state properties of nanomolecules with multi-reference character at a minimal computational cost, we combine TAO-DFT with the polarizable continuum model (PCM). To show its usefulness, TAO-DFT-based PCM (TAO-PCM) is employed to study the electronic properties of linear acenes in three different solvents (toluene, chlorobenzene, and water). According to TAO-PCM, in the presence of these solvents, the smaller acenes should have nonradical nature, and the larger acenes should have increasing polyradical nature, showing remarkable similarities to the past findings in the gas phase.

Given the importance of menstrual blood in the pathogenesis of endometriosis and the multifunctional roles of menstrual mesenchymal stem cells (MenSCs) in regenerative medicine, this issue has gained prominence in the scientific community. Moreover, recent reviews highlight how robust the integrated assessment of omics data is for endometriosis. To our knowledge, no study has applied the multi-omics approaches to endometriosis MenSCs. It is a case-control study at a university-affiliated hospital. MenSCs transcriptome and proteome data were obtained by RNA-seq and UHPLC-MS/MS detection. Among the differentially expressed proteins and genes, we emphasize ATF3, ID1, ID3, FOSB, SNAI1, NR4A1, EGR1, LAMC3, and ZFP36 genes and MT2A, TYMP, COL1A1, COL6A2, and NID2 proteins that were already reported in the endometriosis. Our functional enrichment analysis reveals integrated modulating signaling pathways such as epithelial-mesenchymal transition (↑) and PI3K signaling via AKT to mTORC1 (↓in proteome), mTORC1 signaling, TGF beta signaling, TNFA signaling via NFkB, and response to hypoxia via HIF1A targets (↑in transcriptome). Our findings highlight primary changes in the endometriosis MenSCs, suggesting that the chronic inflammatory endometrial microenvironment can modulate these cells, providing opportunities for endometriosis etiopathogenesis. Moreover, they identify challenges for future research leveraging knowledge for regenerative and precision medicine in endometriosis.

The prediction of drug-target interactions plays a fundamental role in facilitating drug discovery, where the goal is to find prospective drug candidates. With the increase in the number of drug-protein interactions, machine learning techniques, especially deep learning methods, have become applicable for drug-target interaction discovery because they significantly reduce the required experimental workload. In this paper, we present a spontaneous formulation of the drug-target interaction prediction problem as an instance of multi-instance learning. We address the problem in three stages, first organizing given drug and target sequences into instances via a private-public mechanism, then identifying the predicted scores of all instances in the same bag, and finally combining all the predicted scores as the output prediction. A comprehensive evaluation demonstrates that the proposed method outperforms other state-of-the-art methods on three benchmark datasets.

Land cover mapping provides spatial information on the physical properties of the Earth’s surface, for various classes of wetlands, artificial surface and constructions, vineyards, water bodies, etc. Having reliable information on land cover is crucial to developing solutions to a variety of environmental problems such as destruction of important wetlands/forests, and loss of fish and wildlife habitats. This has made land cover mapping one of the most widespread application areas in remote sensing computational imaging. However, due to the differences between modalities in terms of resolutions, content, and sensors, integrating complementary information that multi-modal remote sensing imagery exhibits into a robust and accurate system still remains challenging, and classical segmentation approaches generally do not give satisfactory results for land cover mapping. In this paper, we propose a novel dynamic deep network architecture, AMM-FuseNet, that promotes the use of multi-modal remote sensing images for the purpose of land cover mapping. The proposed network exploits the hybrid approach of the Channel Attention mechanism and Densely Connected Atrous Spatial Pyramid Pooling (DenseASPP). In the experimental analysis, in order to to verify the validity of the proposed method, we test AMM-FuseNet applied to four datasets whilst comparing it to the 6 state-of-the-art models of DeepLabV3+, PSPNet, UNet, SegNet, DenseASPP, and DANet. In addition, we also demonstrate the capability of AMM-FuseNet under minimal training supervision (reduced number of training samples) compared to the state-of-the-art, achieving less accuracy loss even for the case with 1/20 of the training samples.

Pedestrian multi-target tracking technology plays an important role in artificial intelligence, driverless, virtual reality and other fields. The pedestrian multi-target tracking algorithm DeepSORT based on detection is widely used in industry. It mainly tracks multiple pedestrian targets continuously and keeps their ID unchanged. In order to improve the applicability and tracking accuracy of DeepSORT algorithm, this paper improved the IOU distance measurement in the matching process. At the same time, ResNet50 is used as the feature extraction backbone network, and combined with FPN (Feature Pyramid Network), the appearance features of multi-layer pedestrians are fused to improve the tracking accuracy of DeepSORT algorithm. The proposed algorithm is verified on the public data set MOT-16 and it’s tracking accuracy is enhanced to 4.1%.

The present paper is concerned with the study of the quality of life index. Such an index has become an important index for measuring the well-being of individuals. However, the quality of life index is always a subjective, intangible, and often hard to quantify with precision due to the lack of quantitative models dealing with. The main goal of the present paper is thus to propose a mathematical, quantitative model for the measurement of a quality of life index. The main novelty is firstly the construction of a wavelet dynamic multiscale model to quantify and investigate the effect of time scale on the quality of life index measuring. The proposed procedure is acted empirically on a sample corresponding to Saudi Arabia as a case of study during the period from 2003 to 2020 as part of the 2030-vision plan. Saudi Arabia has implemented the so-called 2030-vision plan where the quality of life improvement is one of the main goals to be attempted. The findings show that wavelets are capable to localize the time-wise behavior of the index contrarily to classical studies which estimate a global view of the index. Moreover, the study shows the link between the quality of life behavior and many other indices.

In this study, a new method for synthesizing Au-NaYF4:Yb3+/Er3+-DSPE-PEG2K nanocomposites was introduced. Using a hydrothermal method, the synthesized Yb3+- and Er3+-codoped NaYF4 upconversion luminescent materials and Au nanoparticles were doped into upconversion nanomaterials and modified with DSPE-PEG2k up-conversion nanomaterials. This material is known as Ag-UCNPs-DSPE-PEG2k, it improves both the luminous intensity because of the doped Au nanoparticles and has low cytotoxicity because of the DSPE-PEG2k modified. Exciting UCNPs with a wavelength of 980nm near-infrared light will emit light with a wavelength of 520nm to further excite gold nanoparticles to convert light energy into heat. Successful synthesized gold nanoparticles was confirmed using transmission electron microscopy (TEM). The morphology of UCNPs was observed using scanning electron microscopy (SEM), and the mapping confirmed the successful doping of Au nanoparticles. Fluorescence spectra were used to compare changes in luminescence intensity before and after doping Au nanoparticles. The cytotoxicity of Au-UCNPs-DSPE-PEG2K was tested via the cell counting kit-8 (CCK-8) method, and its imaging ability was characterized using the Magnetic Resonance Imaging (MRI) and Computed Tomography (CT) method.

Background: The COVID-19 pandemic has disproportionately affected people from more deprived communities. The experience of Long Covid is similarly distributed but very few investigations have concentrated on the needs of this population. The aim of this project was to co-produce an acceptable intervention for people with Long Covid, living in communities recognised as more deprived. Methods: The intervention was based on a multi-disciplinary team using approaches from sport and exercise medicine and functional rehabilitation. The co-production process was undertaken with a stakeholder advisory group and patient public involvement representation. This study identified participants by postcode and the indices of multiple deprivation (IMD); recruitment and engagement were supported by an existing health and wellbeing service. A virtual ‘clinic’ was offered with a team of professional practitioners who met participants three times each; to directly consider their needs and offer structured advice. The acceptability of the intervention was based on the individual’s participation and their completion of the intervention. Results: Ten participants were recruited with eight completing the intervention. The partnership with an existing community health and wellbeing service was deemed to be an important way of reaching participants. Two men and six women ages ranging from 38 to 73 were involved and their needs were commonly associated with fatigue, anxiety and depression with overall de-conditioning. None reported serious hardship associated with the pandemic although most were in self-employment/part-time employment or were not working due to retirement or ill-health. Two older participants lived alone, and others were single parents and had considerable challenges associated with managing a household alongside their Long Covid difficulties. Conclusions: This paper presents the needs and perspectives of eight individuals involved in the process and discusses the needs and preferences of the group in relation to their support for self- managed recovery from Long Covid.

A graph based path planning method consisting of off-line part and on-line part for multi-UAV system in windy condition is proposed. In the off-line part, the task area is divided into grids. When two nodes is close enough, they are connected and weighted by the cost, obtained by solving an optimization problem based on difference method, between them. In order to ensure the accuracy of the difference method, the adjacent radius is set to be small enough. In order to ensure the generated paths close to analytical solution, the grid size is set to be much smaller than the adjacent radius. The shortest path algorithm is used to update the adjacent matrix and path matrix. In the on-line part, the target position assignment and optimal velocity can be obtained by accessing the adjacent matrix and path matrix. At the end of this paper, some numerical examples are taken to illustrate the validity of our method and the influence of the parameters.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

Identifying cracks in the incipient state is essential to prevent the failure of engineering structures. Detection methods relying on the analysis of the changes in modal parameters are widely used because of the advantages they present. In our previous research, we have found that eigenfrequencies were capable of indicating the position and depth of damage when sufficient vibration modes were considered. The damage indicator we developed was based on the relative frequency shifts (RFS). To calculate the RFSs for various positions and depths of a crack, we established a mathematical relation that involved the squared modal curvatures in the healthy state and the deflection of the healthy and damaged beam under dead mass, respectively. In this study, we propose to calculate the RFS for beams with several cracks by applying the superposition principle. We demonstrate that this is possible if the cracks are far enough from each other. In fact, if the cracks are close to each other, the superposition method does not work and we distinguish two cases: (i) when the cracks affect the same beam face, the frequency drop is less than the sum of the individual frequency drops, and (ii) on the contrary, cracks on opposite sides cause a decrease in frequency, which is greater than the sum of the frequency drop due to individual damage. When the RFS curves are known, crack assessment becomes an optimization problem, the cost function being the distance between the measured RFSs and all possible RFSs for several vibration modes. Thus, the RFS constitutes a benchmark that characterizes damage using only the eigenfrequencies. We can accurately locate multiple cracks and estimate their severity trough experiments and thus prove the reliability of the proposed method.

The paper describes problems with the current additive manufacturing chain before considering additive manufacturing as part of a modern manufacturing chain. Additive manufacturing can be used for near net-shape for finishing, for repair or for adding special features which cannot be made with traditional manufacturing. This paper describes how STEP-NC deals with these different scenarios in terms of accuracy, multi-material and variation of slice direction. The possibilities of multi-material objects also raises questions about the design of such objects and how these need to be handled by an advanced controller. The paper also describes non-planar slicing. Curved direction and cylindrical direction are shown to improve the accuracy of curved structure additive manufacturing. STEP-NC using boundary representation has better capability of depicting complex internal structures for additive processes. By using exact model of the final product represented by STEP-NC, the paper demonstrates improvements in data size reduction, slicing accuracy, and precise manipulation of internal structure.

Multi-criteria decision-making (MCDM) methods and techniques have been applied to many real-world problems in different fields of engineering science and technology. The evaluation based on distance from average solution (EDAS) method is a new and efficient MCDM method. The aim of this study is to propose a modification to address two exceptional cases in which the EDAS method fails to solve an MCDM problem.

Hydraulic conductivity is the key and one of the most uncertain parameters in groundwater modeling. The grid based numerical simulation require spatial distribution of sampled hydraulic conductivity at un-sampled locations in the study area. This spatial interpolation has been routinely performed using variogram based models (two-point geostatistics methods). These traditional techniques fail to capture the complex geological structures, provides smoothing effects and ignore the higher order moments of subsurface heterogeneities. In this work, a multiple-point geostatistics (MPS) method is applied to interpolate hydraulic conductivity data which will be further used in WASH123D numerical groundwater simulation model for regional smart groundwater management. To do this, MPS need ‘training images (TIs) as a key input. TI is a conceptual model of subsurface geological heterogeneity which was developed by using concept of ages, topographic slope as an index criteria and knowledge of geologist. After considerations of full physics of study area, an example shows the advantages of using multiple-point geostatistics compared with the traditional two-point geostatistics methods (such as Kriging) for the interpolation of hydraulic conductivity data in a complex geological formation.

Mining interspecies interactions remain a challenge due to the complex nature of microbial communities and the need for computational power to handle big data. Our meta-analysis indicates that genetic potential alone does not resolve all issues involving mining of microbial interactions. Nevertheless, it can be used to define the building blocks to infer synergistic interspecies interactions and to limit the search space (i.e., number of species and metabolic reactions) to a manageable size. A reduced search space decreases the number of additional experiments necessary to validate the inferred putative interactions. As validation experiments, we examine how multi-omics and state of the art imaging techniques may further improve our understanding of species interactions’ role in ecosystem processes. Finally, we analyze pros and cons from the current methods to infer microbial interactions from genetic potential and propose a new theoretical framework based on: (i) genomic information of key members of a community; (ii) information of ecosystem processes involved with a specific hypothesis or research question; (iii) the ability to identify putative species’ contributions to ecosystem processes of interest; and, (iv) validation of putative microbial interactions through integration of other data sources.

The proportion of area under various crops at a given point in time, known as a cropping pattern, plays an essential role in determining the level of agricultural production. In this study, cropping patterns of three sub-counties in Murang’a County, a typical African smallholder farming area in Kenya, were mapped. Specifically, we compared the performance of eight classification scenarios for mapping cropping patterns; namely using (i) only Sentinel-2 reflectance bands (S2), (ii) S2 and S2 derived vegetation indices (VIs); (iii) S2 and S2 vegetation phenology (VP); (iv) S2 and Sentinel-1 radar backscatter data (S1); (v) S2, VIs, and S1; (vi) S2, VP, and S1; (vii) S2, VIs and VP, and (viii) S2, VIs, VP and S1. Reference data of the dominant cropping patterns and non-croplands were collected. The guided regularized random forest (GRRF) algorithm was used to select the optimum variables and to perform the respective classification for each scenario. The most accurate result of the overall accuracy of 93.16% was attained from the scenario (viii) S2, VIs, VP, and S1. The McNemar’s test of significance did not show significant differences (p≤0.05) among the tested scenarios. Our study demonstrated the strength of GRRF and the synergetic advantage of S2 and S1 derivatives to map cropping patterns in a heterogeneous landscape where high resolution imagery are inaccessible. Our cropping pattern mapping approach can be used in other sites of relatively similar agro-ecological conditions.

In research applications across several areas, noise removal is indispensable for accuracy of final results. Noise is caused due to physical principals, such as background electronic noise, quantum effect, and wave rebound effect to name a few. Noise removal can help improve results in medical, astronomy, defense, and numerous other fields. Addressing this limitation would result in potentially low cost, automatic, and reliable systems. In this paper, a generalized new approach i.e. Multi-Frame Noise Removal (MFNR) is proposed for noise removal. Given any type of data, the probability density function (PDF) of the noise can be determined. Herein, we extracted the noise PDF parameters using KDE (Kernel Density Estimation). Because the data is corrupted by “deterministic” noise, hence can be cleaned. This could be used as a general purpose noise removal tool. The data point with same position in multiple frames helps us determine the noise PDF characteristics and hence making it possible to remove noise. The conventional wisdom which states that noise removal and detail preservation are contrary to each other is not true for MFNR. Experimental results validate our proposed method which showed practically complete noise reduction based on number of frames used, as compared to existing benchmark methods.

The interaction between single or a fixed number of photons with a single absorber is of fundamental interest in quantum technology. The harnessing of light matter interactions at the single particle limit has several potential applications ranging from quantum communication and quantum metrology to quantum imaging. In this letter, a setup for heralded two-photon absorption at the single absorber level is proposed. The setup is based on a heralded two-photon source utilizing spontaneous parametric down-conversion, entanglement swapping and sum frequency generation for joint detection. The feasibility of the scheme is discussed by reviewing recent achievements in utilizing entangled and correlated photons for two-photon absorption as well as single photon absorption experiments at the limit of single absorbers in the context of applications in imaging (here mainly microscopy) and spectroscopy.

Changes in land-use have been observed in banana-based systems in the African Great Lakes region affected by Xanthomonas wilt disease (XW) of banana. Through participatory focus group discussions (FGDs) and the 4-cell method, changes in land-use were retrospectively assessed in 13 XW-affected landscapes/villages along a 230 km transect from Masisi (XW arrived in 2001) to Bukavu (XW arrived around 2014) in eastern Democratic Republic of Congo during 2015. The four-cell chart ranked land-use by mapping the area under production and the number of households involved in production. Farmers’ perceptions on the sustainability of new land-uses were also documented. Soil nutrient content and erosion levels were measured for five major land-use options/ trajectories on 147 fields across 55 farms in three landscapes along the transect. From being ranked the most important crop (92% of landscapes i.e. produced on large areas of land and by many households) before XW outbreaks, its importance had declined with most households in 36% of the landscapes growing it on smaller farms while in 64% of cases by few households on smaller pots. Farmers uprooted entire banana mats or fields, expanding land under other crops, mainly beans, taro, sweet potato, cassava, maize, coffee and eucalyptus. Species richness did not change at landscape level, though 21 crops were introduced at farm level. Land-use for banana is however still perceived to be more sustainable due to its multi-functional roles. Soils under banana plots were found in general to be better in their chemical attributes while high erosion levels (Mg ha-1 year-1) were observed under cassava (1.7-148.9) compared with banana (0.3-10.7) and trees (0.3-5.9). The current shift away from banana could thus have profound effects on supply of key services and sustainability of the production systems. This study offers a good basis/entry point for interventions in the XW-affected landscapes.