This paper shows a method for pipeline leak detection using a transient-based method with MATLAB® functions. The simulation of a pipeline systems in the time domain are very complex. In the case of the dissipative model, transfer functions are hyperbolic Bessel functions. Simulating a pipeline system in the frequency domain using a dissipative model we could find an approximate transfer function with equal frequency domain response to in order get the pipeline system's time domain response. The method described in this paper can be used to detect, by comparison, to detect a leak in a pipeline system model.

ABSTRACT Ethiopia is a developing country, where majority of the population lives in rural areas without access to electricity. 83% of the total population of the country use traditional biomass energy as a basic source of energy. In contrast, the country is endowed with sufficient renewable energy resources which can be used as a standalone electric energy supply system for electrifying remote areas of the country. These resources are mainly micro hydropower and wind which can be used individually or the best combination of one another. The application of hybrid renewable energy system has become an important alternative solution for rural electrification program. The Modeling and control of a hybrid PV-Wind-Hydro DG system is also addressed. Dynamic models for the major system components, namely, wind energy conversion system, PV energy conversion system, hydro, inverter, and overall fuzzy logic controller units are developed. Then, a simulation model for the proposed hybrid power system has been developed using MATLAB /Simulink environment. This is done by creating subsystem sets of the major dynamic component models and then assembling into a single aggregate model. The overall power management strategy for coordinating and/or controlling the different energy sources is also presented in the thesis work. Generally there are 800 households with total electric demand of 71.6KW.To satisfy this demand 52%, 35% and 13% is to be contributed from wind/hydro/solar respectively. To use the power economically fuzzy logic controller is used. The controller monitors the demand and the available sources and then switches to the appropriate power supply according to the written rules. Simulations have been carried out to verify the system dynamic performance using a practical load profile and weather data. The result shows that the overall power management strategy is effective and the load demand is balanced. To complete this work, a grid extension from the closest substation has been compared with hybrid system. Cost of the grid extension is estimated based on the data obtained from EEP office. This is done in order to compare the cost of the designed hybrid power system against the cost of grid extension. The result shows that breakeven grid extension distance to be 23.9km which indicates that grid extension is preferable.

The early-mid Paleocene Farewell Formation is stratigraphically distributed across the southern Taranaki Basin (STB) which is also encountered within the Maui Gas Field. Using available 3D seismic and well log data, a challenging task to delineate the spatial distribution and geobody patterns of the potential reservoir sands of the formation was performed. Object based modeling coupled with sequential indicator simulation were used to analyze the spatial distribution of facies configuration and a conceptual model was developed based on the outputs from the structurally- modeled grids. The facies modeling followed a hierarchical object-based mechanism which was set to perform with constraints like channel geometry and heterogeneity within the formation. The resultant 3D geobody model showed that the distributary channels, mainly braided geobodies flowed from northeast cutting through several regional normal-fault systems to the southwest. Overbank facies was adhered to the fringe of the channels whereas the floodplain facies was at the periphery of the model. Meandering channel-sand facies were mostly observed at the center of the model flowing in a more random manner, occupying major flow directions of northwest to southwest and southeast to northwest within the model.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

A novel coronavirus called 2019-nCoV was recently found in Wuhan, Hubei Province of China, and now is spreading across China and other parts of the world. 2019-nCoV spreads more rapidly than SARS-CoV. Unfortunately, there is no drug to combat the virus. It is of high significance to develop a drug that can combat the virus effectively before the situation gets worse. It usually takes a much longer time to develop a drug using traditional methods. For 2019-nCoV, it is now better to rely on some alternative methods to develop drugs that can combat such a disease effectively since 2019-nCoV is highly homologous to SARS-CoV. In this paper, we first collected virus RNA sequences from the GISAID database, translated the RNA sequences into protein sequences, and built a protein 3D model using homology modeling. Coronavirus main protease is considered to be a major therapeutic target, thus this paper focused on drug screening based on the modeled 2019-nCov_main_protease structure. The deep learning based method DFCNN, developed by our group, can identify/rank the protein-ligand interactions with relatively high accuracy. DFCNN is capable of performing virtual screening quickly since no docking or molecular dynamic simulation is needed. DFCNN identifies potential drugs for 2019-nCoV protease by performing drug screening against 4 chemical compound databases. Also, we performed drug screening for all tripeptides against the binding site of 2019-nCov_main_protease since peptides often show better stability, more bio-availability and negligible immune responses. In the end, we provided the list of possible chemical ligands and peptide drugs for experimental validation.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

Small and micro hydropower represents an attractive solution for electricity generation, with low cost and low environmental impact. The pump-as-turbine (PAT) approach has promise in this application owing to its low purchase and maintenance costs. In this paper, a new method to predict the inverse characteristic of industrial centrifugal pumps is presented. This method is based on results of simulations performed with commercial three-dimensional CFD software. Model results have been first validated in pumping mode using data supplied by pump manufacturers. Then, results have been compared to experimental data for a pump running in reverse condition. Experimentation has been performed on a dedicated test bench installed in the Department of Civil Construction and Environmental Engineering of the University of Naples Federico II. Three different pumps, with different specific speeds, have been analyzed. Using the model results, the inverse characteristic and the best efficiency point have been evaluated. Finally, results of this methodology have been compared to prediction methods available in the literature.

Biomolecular structure drives function, and computational capabilities have progressed such that the prediction and computational design of biomolecular structures is increasingly feasible. Because computational biophysics attracts students from many different backgrounds and with different levels of resources, teaching the subject can be challenging. One strategy to teach diverse learners is with interactive multimedia material that promotes self-paced, active learning. We have created a hands-on education strategy with a set of fifteen modules that teach topics in biomolecular structure and design, from fundamentals of conformational sampling and energy evaluation to applications like protein docking, antibody design, and RNA structure prediction. Our modules are based on PyRosetta, a Python library that encapsulates all computational modules and methods in the Rosetta software package. The workshop-style modules are implemented as Jupyter Notebooks that can be executed in the Google Colaboratory, allowing learners access with just a web browser. The digital format of Jupyter Notebooks allows us to embed images, molecular visualization movies, and interactive coding exercises. This multimodal approach may better reach students from different disciplines and experience levels as well as attract more researchers from smaller labs and cognate backgrounds to leverage PyRosetta in their science and engineering research. All materials are freely available at https://github.com/RosettaCommons/PyRosetta.notebooks.

The prevalence of differential equations as a mathematical technique has refined the fields of control theory and constrained optimization due to the newfound ability to accurately model chaotic, unbalanced systems. However, in recent research, systems are increasingly more nonlinear and difficult to model using Differential Equations only. Thus, a newer technique is to use policy iteration and Reinforcement Learning, techniques that center around an action and reward sequence for a controller. Reinforcement Learning (RL) can be applied to control theory problems since a system can robustly apply RL in a dynamic environment such as the cartpole system (an inverted pendulum). This solution successfully avoids use of PID or other dynamics optimization systems, in favor of a more robust, reward-based control mechanism. This paper applies RL and Q-Learning to the classic cartpole problem, while also discussing the mathematical background and differential equations which are used to model the aforementioned system.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

Background: Tourism is one of the prominent industry that has a capability to generate handsome income for developed as well as developing countries. However, the study to investigate specifically the perception of local residents towards tourism is still lacking. The perception of the locals is important since it could determine the extent of their support for tourism development. Plus, previous research found that male residents are more support better towards the tourism development. Thus, this factor is adapted as well in this study to examine whether this gender may influence to the tourism industry. 2) Methods: This study used Structural Equation Modeling (SEM) technique for determining the structural estimates between constructs. 3) Results: The respondents agree that positive perception, negative perception and tourism impact has a significant impact on support for tourism development in which has been recognized as Social Exchange Theory model. Moreover, the finding also revealed that gender has a potential to moderates the causal effect of tourism impact on tourism development. 4) Conclusion: The resident understand the tourism sector could strengthen economic nation but they also want the natural resources should be protected.

Using recent developments in econometrics and computational statistics we consider the estimation of the instantaneous rate of asset return process when the underlying Data Generating Mechanism (DGM) is an Ornstein-Uhlenbeck process, driven by fractional noise, and sampled at fixed intervals of length h. To address the problem we adopt throughout the paper an exact discretization approach. This enable us to exploit the fact that a flow sampling scheme arises naturally when observing the DGM. For, while the instantaneous rate of return process is unobservable at points in time, its time integral over successive observations is observable since it equals the increment of log-prices. Exact discretization delivers an ARIMA(1,1,1) model for log-prices with a fractional driving noise. Building on the resulting exact discretization formulae and covariance function, a new Markov Chain Monte Carlo (MCMC) scheme is proposed and we examine the properties of both the time and frequency domain likelihoods / posteriors through Monte Carlo. For the exact discrete model we adopt a general sampling interval of length h. This allow us to determine the optimal choice of h independent of the sample size. An empirical application using high frequency stock price data is presented showing the relevance of aggregation over time issues in modelling asset prices.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

We applied a generalized SEIR epidemiological model to the recent SARS-CoV-2 outbreak in the world, with a focus on Italy and its Lombardia, Piemonte, and Veneto regions. We focus on the application of a stochastic approach in fitting the model numerous parameters using a Particle Swarm Optimization (PSO) solver, to improve the reliability of predictions in the medium term (30 days). We analyze the official data and the predicted evolution of the epidemic in the Italian regions, and we compare the results with data and predictions of Spain and South Korea. We link the model equations to the changes in people’s mobility, with reference to Google’s COVID-19 Community Mobility Reports. We discuss the effectiveness of policies taken by different regions and countries and how they have an impact on past and future infection scenarios.

This paper presents a method for a decentralised peer-to-peer software license validation system using cryptocurrency blockchain technology to ameliorate software piracy, and to provide a mechanism for software developers to protect copyrighted works. Protecting software copyright has been an issue since the late 1970's and software license validation has been a primary method employed in an attempt to minimise software piracy and protect software copyright. The method described creates an ecosystem in which the rights and privileges of participants are observed.

The Rosetta software suite for macromolecular modeling, docking, and design is widely used in pharmaceutical, industrial, academic, non-profit, and government laboratories. Considering its broad modeling capabilities, Rosetta consistently ranks highly when compared to other leading methods created for highly specialized protein modeling and design tasks. Developed for over two decades by a global community of scientists at more than 60 institutions, Rosetta has undergone multiple refactorings, and now comprises over three million lines of code. Here we discuss the methods developed in the last five years, involving the latest protocols for structure prediction, protein–protein and protein–small molecule docking, protein structure and interface design, loop modeling, the incorporation of various types of experimental data, and modeling of peptides, antibodies and other proteins in the immune system, nucleic acids, non-standard amino acids, carbohydrates, and membrane proteins. We briefly discuss improvements to the energy function, user interfaces, and usability of the ­­software. Rosetta is available at www.rosettacommons.org.

Hydrological processes are complex to compute on hilly areas when compared to the plain areas. Most of the hydrological model do not take into account the critical rainfall-runoff generation processes such as subsurface storm flow, saturation excess flow, overland flow, return flow and pipe storage. The simulations of the above processes in the soil matrix requires detailed hillslope hydrological modelling. In present study, a hillslope experimental plot is designed to study the runoff generation processes on the plot scale. The setup is designed keeping in view the natural hillslope conditions prevailing in the north western Himalayas, India where high intensity storm event occurs frequently. Using the experimental data and the developed conceptual model, the overland flow and the subsurface flow through macropore dominated area has been estimated/analyzed on the pixel basis. Over the experimental hillslope plot, a rainfall simulator was installed to generate the rainfall intensity in the range of 15 to 150 mm/hr which represented the dominating rainfall intensity range in the region. Soil moisture sensors were also installed at 100 mm and 300 mm depth at different locations of the plot to observe soil moisture variations. It was found that once the soil is saturated, it remains in the field capacity for next 24-36 hours. Such antecedent moisture conditions are most favorable for the generation of rapid stormflow from hillslopes. Dye infiltration test was also performed on the undisturbed soil column to observe the macropore fraction variability over the vegetated hillslopes. The surface runoff predicted using the developed hillslope hydrological model compared well with the observed surface runoff under high intensity rainfall conditions.

Building information modeling (BIM) is the digital representation of physical and functional characteristics (such as geometry, spatial relationship, and geographic information) of a facility to support decisions during its life cycle. BIM has been extended beyond 3D geometrical representations in recent years, and now includes time as a fourth dimension and cost as a fifth dimension, as well as such other applications as virtual reality and augmented reality. The Internet of Things (IoT) has been increasingly applied in various products (smart homes, wearables) to enhance work productivity, living comfort, and entertainment. However, research addressing the integration of these two technologies (BIM and IoT) is still very limited, and has focused exclusively on the automatic transmission of sensor information to BIM models. This paper describes an attempt to represent and visualize sensor data in BIM with multiple perspectives in order to support complex decisions requiring interdisciplinary information. The study uses a university campus as an example and includes several scenarios, such as an auditorium with a dispersed audience and energy saving options for rooms with different functions (mechanical/electric equipment, classrooms, and laboratory). This paper also discusses the design of a common platform allowing communication among sensors with different protocols (Arduino, Raspberry Pi), the use of Dynamo to accept sensor data as input and automatically redraw visualized information in BIM, and how visualization may help in making energy-saving management decisions.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

The outbreak of 2019-novel coronavirus (SARS-CoV-2) that causes severe respiratory infection (COVID-19) has spread in China, and the world health organization declared it pandemic. However, no approved drug or vaccines are available, and treatment is mainly supportive and through a few repurposed drugs. In this urgency situation, development of SARS-CoV-2 based vaccines is immediately required. Immunoinformatic and molecular modelling are generally used time-efficient methods to accelerate the discovery and design of the candidate peptides for vaccine development. In recent years, the use of multiepitope vaccines is proved to be a promising immunization strategy against viruses and pathogens, which induce more comprehensive protective immunity. The current study demonstrated a comprehensive in-silico strategy to design stable multiepitope vaccine construct (MVC) from B-cell and T-cell epitopes of essential SARS-CoV-2 proteins with the help of adjuvants and linkers. The integrated molecular dynamics simulations analysis revealed the stability of MVC and its interaction with human Toll-like receptors (TLRs), which trigger an innate and adaptive immune response. Later, the in-silico cloning in a known pET28a vector system also estimated the possibility of MVC expression in E. Coli. Despite this study lacks validation of this vaccine construct in terms of its efficacy, the current integrated strategy encompasses the initial multiple epitope vaccine design concepts. After validation, this MVC can present to be a better prophylactic solution against COVID-19.

We analyzed the SARS-CoV-2 spike (S) protein amino acid sequence extracted from 11,542 viral genomic sequences submitted to the Global Initiative on Sharing All Influenza Data (GISAID) database through April 27, 2020. Consistent with prior reports, we found a major S protein mutation, D614 to G614, that was represented in 56% of all the analyzed sequences. All other mutations combined were less than 10%. After parsing the data geographically, we found most of the Chinese patient samples showed D614 (97%). By contrast, most patient samples in many European countries showed G614 (51 to 88%). In the United States, the genotypic distribution in California and Washington was similar to Asian countries, while the distribution in other US states was comparable to Europe. We observed a dramatic increase in the frequency of G614 over time in multiple regions, surpassing D614 when both were present, suggesting G614 S protein virus outcompetes D614 S protein virus. To gain insight into the consequences of the D614G mutation, homology modeling using a multi-template threading mechanism with ab initio structural refinement was performed for a region of the S protein (S591 to N710) spanning the D614G mutation and the S1 furin cleavage site. Molecular models of this region containing D614 or G614 revealed a major difference in secondary structure at the furin domain (RRARS, R682 to S686). The D614 model predicted a random coil structure in the furin domain whereas the G614 model predicted an alpha helix. Critical residues in the cleavage domain of G614 model were found to better align with the PDB structure of a furin inhibitor. Thus, homology modeling studies suggest a potential mechanism whereby the D614G mutation may confer a competitive advantage at the furin binding domain that may contribute to the rise of the D614G SARS-CoV-2 mutant.

The role of human resource management practices and organizational loyalty dealing with employee retention has been widely explored and examined in the existing literature. The majority of human resource management researchers have focused on the role of policies and practices in different sectors related to employee retention. However, less attention has been given to identifying the practices and procedures common across all industries and sectors. The present study attempts to determine and examine the most important constructs like HR practices and organizational loyalty of employee retention management and proposes a comprehensive structural equation model to measure the impact of these constructs on employee retention. After an extensive review of the literature, organizational loyalty, and human resources management practices like recruitment and selection, compensation and benefit, training and development, supervision and evaluation have been identified as four essential practices dealing with employee retention and are common across all industries. These practices constitute the component factors of an employee retention management predicting employee’s turnover intentions. The survey method was adopted, and the original data obtained through the self-administered questionnaire. The valid one hundred and eighty-nine (189) respondents analyzed by using Lisrel 8.7, Structural equation model (SEM) analysis results shows that human resource management practices and organizational loyalty have strong positive impact on employee retention. This study tends to assist human resource managers and decision makers in selecting the appropriate motivating factors to retain and satisfy their employees

Identification of costs drivers and their influence level on building development costs play a key role in the development of construction models and improve the efficiency and effectiveness of any project. Forty-five indicators influencing building development costs in New Zealand are explored by literature review and pilot interviews. These indicators are grouped into seven categories. The determination and ranking of the cost drivers are carried out by a questionnaire survey distributed to key professionals working in New Zealand’s construction industry. Structural equation modeling (SEM) software was employed for analysis of the collected data. One of the key advantages of this powerful software is to provide the p-value according to the structure of the research model. Findings of this study indicate that the property market and construction industry factor, statutory and regulatory factor, and socio-economic factor are major factors affecting building development costs in New Zealand.

Building Information Modelling (BIM) has been more popular in the construction industry as a consequence of the many advantages it offers, such as increased productivity, improved project outcomes, and reduced expenses. However, there are many obstacles that must be overcome before BIM can be widely used. This research uses a poll of construction industry experts to investigate the challenges associated with using BIM in projects. Cost of implementation, inadequate standards and procedures, and a lack of knowledge with BIM were some of the hurdles that were measured in the study. Statistical techniques were used to examine the data, and the findings indicate that the high cost of implementation and the absence of sufficient standards and procedures are the two main obstacles to the widespread adoption of BIM. Problems with supply chain management and a lack of experience with BIM are also mentioned as obstacles. The report also suggests solutions, such as a more focused teaching effort on BIM-related issues and the creation of a specialised BIM curriculum. Professionals in the construction industry may utilise the study’s results to their advantage by expanding their knowledge of the obstacles standing in the way of widespread adoption of BIM.

In power systems there are complex transformer structures, whose accurate analysis is not possible using the techniques available today. This paper presents a systematic data driven analysis method for coupled inductors of arbitrary complexity. The method first establishes a winding matrix N mapping the windings to the limbs of the transformer. A permeance matrix P is created from the reluctance network of the magnetic core. A generalized inductance matrix L mapping currents in the transformer windings to the induced voltages is generated based on the winding (N) and permeance (P) matrices. The inductance matrix representation of a coupled inductor is then transformed to an admittance matrix, which can be integrated to the nodal analysis of the electrical circuit surrounding the coupled inductor. The method presented is validated by simulations with real transformer structures using electromagnetic transient program (EMTP/ATP).

The apicomplexan parasite, Sarcocystis neurona causes the degenerative neurological equine protozoal myeloencephalitis (EPM) disease of horses. Due to its host range expansion, S. neurona is an emerging threat that requires close monitoring. In apicomplexans, protein kinases (PKs) have been implicated in a myriad of critical functions such as host cell invasion, cell cycle progression and host immune responses evasion. Here, we used various bioinformatics methods to define the kinome of S. neurona and phylogenetic relatedness of its PKs to other apicomplexans. Further, three-dimensional (3D) homology models for selected S. neurona putative PKs were constructed and evaluated for inhibitor docking. We identified 92 putative PKs clustering within the AGC, CAMK, CK1, CMGC, STE, TKL, aPK and OPK groups. Although containing the universally conserved PKA (AGC group), S. neurona kinome was devoid of PKB and PKC, but contained the six apicomplexan conserved CDPKs (CAMK group). The OPK group was represented by ROPKs 19A, 27, 30, 33, 35 and 37, but was devoid of the virulence-associated ROPKs 5, 6, 18 and 38. Two out of the three S. neurona CK1 enzymes had high sequence similarities to T. gondii TgCK1-α and TgCK1-β and the Plasmodium PfCK1. Docking of four inhibitors onto homology models of putative ROP27 and PKA indicated that inhibition of S. neurona PKs is feasible, but needs to be experimentally tested. The essentiality of apicomplexan PKs makes the elucidation of S. neurona kinome a key milestone for development of novel therapeutics for EPM.

This paper presents the validation of the End Point Rate (EPR) tool for QGIS (EPR4Q), a tool built-in QGIS Graphical Modeler to calculate the shoreline change by End Point Rate method. The EPR4Q tries to fill the gap of user-friendly and free open-source tool for shoreline analysis in Geographic Information System environment, since the most used software - Digital Shoreline Analysis System (DSAS) - although is a free extension, is suited for commercial software. Besides, the best free open-source option to calculate EPR called Analyzing Moving Boundaries Using R (AMBUR), since it is a robust and powerful tool, the complexity and heavy processes can restrict the accessibility and simple usage. The validation methodology consists of applying the EPR4Q, DSAS, and AMBUR on different examples of shorelines found in nature, extracted from the U.S. Geological Survey Open-File. The obtained results of each tool were compared with Pearson correlation coefficient. The validation results indicate that the EPR4Q tool created acquired high correlation values with DSAS and AMBUR, reaching a coefficient of 0.98 to 1.00 on linear, extensive, and non-extensive shorelines, guarantying that the EPR4Q tool is ready to be freely used by the academic, scientific, engineering, and coastal managers communities worldwide.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

Wireless Sensor Networks (WSNs) are being increasingly adopted in critical applications, where verifying the correct operation of sensor nodes is a major concern. Undesired events may undermine the mission of the WSNs. Hence their effects need to be properly assessed before deployment to obtain a good level of expected performance and during the operation in order to avoid dangerous unexpected results. In this paper we propose a methodology to support design and deployment of dependable WSNs by means of an event-based formal verification technique. The methodology includes a process to guide designers towards the realization of a dependable WSN and a tool ("ADVISES") to simplify its adoption. The tool allows to generate automatically formal specifications used to check correctness properties and evaluate dependability metrics at design time and at runtime. During the runtime we can check the behavior of theWSN accordingly to the results obtained at design time and we can detect sudden and unexpected failures, in order to trigger recovery procedures. The effectiveness of the methodology is shown in the context of two case studies, aiming to illustrate how the tool is helpful to drive design choices and to check the correctness properties of theWSN at runtime

Food systems will need to undergo considerable transformation. To be better prepared for and resilient to uncertainty and disturbances in the future, resource users and managers need to further develop knowledge about the food and farming system, with its dominating feedback structures and complexities, and to test robust and integrated system-based solutions. This paper investigates how participatory system dynamics modeling can be adapted to groups at the community level with low or no formal educational background. The paper also analyzes the refinement of workshop participants’ mental models as a consequence of a participatory system dynamics intervention. For this purpose, we ran two workshops with small-scale farmers in Zambia. Analysis of workshop data and post-workshop interviews shows that participatory system dynamics is well adaptable to support an audience-specific learning-by-doing approach. The use of pictures, objects and water glasses in combination with the basic aspects of causal loop diagramming makes for a well-balanced toolbox. Participants acquire understanding that is also relevant beyond systems thinking in that is offers a range of practical insights such as a critical evaluation of common food security strategies.

Megacities are complex systems facing the challenges of overpopulation, poor urban design and planning, poor mobility and public transport, poor governance, climate change issues, poor sewerage and water infrastructure, waste and health issues, and unemployment. Smart cities have emerged to address these challenges by making the best use of space and resources for the benefit of citizens. A smart city model views the city as a complex adaptive system consisting of services, resources, and citizens that learn through interaction and change in both the spatial and temporal domains. The characteristics of dynamic development and complexity are key issues for city planners that require a new systematic and modeling approach. Multiscale modeling (MM) is an approach that can be used to better understand complex adaptive systems. The MM aims to solve complex problems at different scales, i.e., micro, meso, and macro, to improve system efficiency and mitigate computational complexity and cost. In this paper, we present an overview of MM in smart cities. First, this study discusses megacities, their current challenges, and their emergence to smart cities. Then, we discuss the need of MM in smart cities and its emerging applications. Finally, the study highlights current challenges and future directions related to MM in smart cities, which provide a roadmap for the optimized operation of smart city systems.

During its first month, the recently emerged 2019 Wuhan novel coronavirus (SARS-CoV-2) has already infected many thousands of people in mainland China and worldwide and took hundreds of lives. However, the swiftly spreading virus also caused an unprecedentedly rapid response from the research community facing the unknown health challenge of potentially enormous proportions. Unfortunately, the experimental research to understand the molecular mechanisms behind the viral infection and to design a vaccine or antivirals is costly and takes months to develop. To expedite the advancement of our knowledge we leverage the data about the related coronaviruses that is readily available in public databases, and integrate these data into a single computational pipeline. As a result, we provide a comprehensive structural genomics and interactomics road-maps of SARS-CoV-2 and use these information to infer the possible functional differences and similarities with the related SARS coronavirus. All data are made publicly available to the research community at http://korkinlab.org/wuhan .

Currently, narrowband Power line communication (PLC) is considered as an attractive communication system in smart grid environments for applications such as advanced metering infrastructure (AMI). In this paper, we will present a comprehensive comparison and analysis in time and frequency domain of noise measured in China and Italy. In addition, impulsive noise in these two countries are mainly analyzed and modeled using two probability based models, Middleton Class A (MCA) model and \(\alpha\) stable distribution model. The results prove that noise measured in China is rich in impulsive noise, and can be modeled well by \(\alpha\) stable distribution model, while noise measured in Italy has less impulsive noise, and can be better modeled by MCA model.

The importance of predicting the exposure to environmental hazards is highlighted by issues like global climate change, public health problems caused by environment stresses, and property damages and depreciations. Several approaches have been used to assess potential exposure and achieve optimal results under various conditions, for example, for different scales, groups of people, or certain points in time. Micro-simulation tools are becoming increasingly important in human exposure assessment, where each person is simulated individually and continuously. This paper describes an agent-based model (ABM) framework that can dynamically simulate human exposure levels, along with their daily activities, in urban areas that are characterized by environmental stresses such as air pollution and heat stress. Within the framework, decision making processes can be included for each individual based on rule-based behavior to achieve goals under changing environmental conditions. The ideas described in this paper are implemented in a free and open source NetLogo platform. A simplified modeling scenario of the ABM framework in Hamburg, Germany, further demonstrates its utility in various urban environments and individual activity patterns, and portability to other models, programs and frameworks. The prototype model can potentially be extended to support environmental incidence management by exploring the daily routines of different groups of citizens and compare the effectiveness of different strategies. Further research is needed to fully develop an operational version of the model.

The possibility of using additive manufacturing (AM) in the medicine area has created a new opportunities in health care. This has contributed to a sharp increase in demand for 3D printers, their systems and materials that are adapted to strict medical requirements. We described herein a medical-grade thermoplastic polyurethane (S-TPU), which was developed and then formed into a filament for Fused Deposition Modeling (FDM) 3D printers during a melt-extrusion process. S-TPU consisting of aliphatic hexamethylene 1,6-diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) (PEBA) and 1,4 butandiol (BDO) as a chain extender, was synthesized without the use of a catalyst. The filament properties were characterized by rheological, mechanical, physico-chemical and in vitro biological properties. The tests showed biocompatibility of the obtained filament as well as revealed no significant effect of the filament formation process on its properties. This study may contribute to expanding the range of medical-grade flexible filaments for standard low-budget FDM printers.

Myocardial heterogeneity is an attribute of the normal heart. We have developed integrative models of cardiomyocytes from the subendocardial (ENDO) and subepicardial (EPI) ventricular regions that take into account experimental data on specific features of intracellular electromechanical coupling in the guinea pig heart. The models adequately simulate experimental data on the action potential and contraction of the ENDO and EPI cells. The modeling results predict that heterogeneity in the parameters of calcium handling and myofilament mechanics in isolated ENDO and EPI cardiomyocytes via cooperative mechanisms of mechano-calcium-electric feedback are essential to produce the differences in Ca²⁺ transients and contraction profiles and may further enhance transmural differences in the electrical properties between the cells. Simulation results predict that ENDO cells have greater sensitivity to changes in afterload than EPI cells. These data are important for understanding the behavior of cardiomyocytes in the intact heart.

The accurate wellbore pressure control not only prevents from lost circulation/blowout and fracturing formation by managing density of drilling fluid, but also improves productivity by mitigating reservoir damage. The geothermal pressure calculated by constant parameters for geothermal well would bring big error easily, as the changes of physical, rheological and thermal properties of drilling fluids with temperature were neglected. This paper researches the wellbore pressure coupling by calculating the temperature distribution with existed model, fitting the rule of density of drilling fluid with temperature and establishing mathematical models to stimulate the wellbore pressures, which is expressed as the variation of Equivalent Circulating Density (ECD) under different conditions. With this method, temperature and ECDs in the wellbore of the first medium-deep geothermal well ZK212 Yangyi Geothermal Field in Tibet were determined, and the sensitivity analysis was simulated by assumed parameters, i.e. circulating time, flow rate, geothermal gradient, diameters of wellbore, rheological models and regimes, the results indicated the geothermal gradient and flow rate were the most influence parameters on the temperature and ECD distribution, and additives added in drilling fluid should be careful which would change the properties of drilling fluid and induce the temperature redistribution. To make sure the safe drilling, velocity of pipes tripping into the hole, depth and diameter of wellbore are considered to control the surge pressure.

Brine-dependent recovery process has seen much global research efforts in the past two decades because of their benefits over other oil recovery methods. The process involves the tweaking of the ionic composition and strength of the injected water to improve oil production. In recent years, several studies ranging from laboratory coreflood experiments by many researchers to field trials by several companies admit to the potential of recovering additional oil in sandstone and carbonate reservoirs. Sandstone and carbonate rocks are composed of completely different minerals, with varying degree of complexity and heterogeneity, but wettability alteration has been widely considered as the consequence rather than the cause of brine-dependent recovery. However, there is no consensus on the cause as several mechanisms have been proposed to relate the wettability changes to the improved recovery. This review paper aims to provide a state-of-the-art development in published research and various efforts of the industry. This review outlines an overview of laboratory and field observations, descriptions of underlying mechanisms and their validity, the complexity of the oil-brine-rock interactions, modelling works, and comparison between sandstone and carbonate rocks. The provided information is intended to provide the reader with up-to-date information, point to relevant studies for those who are new and those implementing either laboratory- or field-scale projects to speed up the process of further investigations in this research area. Overall, the outcome of this review would potentially be of immense benefit to the oil industry.

Stunting, during the Covid-19 pandemic, is increasingly becoming a big problem in the world, especially in poor and developing countries. Observational studies have shown that stunting is associated with poor nutrition, especially a plant-based diet, inflammation, caused by infection, enteric dysfunction, an environment with clean water, inadequate sanitation and hygiene (WASH), and endogenous inflammation associated with excess adiposity. This causes nutritional interventions to be often unsuccessful (Kemenkes RI, 2018).The government intervenes to reduce stunting to the target party, which is divided into two categories. The first category is specific nutrition intervention, namely monitoring children under five at the posyandu, giving immunizations, giving vitamin A, giving Supplementary Foods (PMT), and others. The second category is sensitive nutrition interventions, namely the provision of drinking water and proper sanitation, postnatal family planning (KB) services, providing information related to stunting, food social assistance, conditional cash assistance, and others. (KEMEN-PMK, 2018). WHO states, that the impact of stunting can be divided into short-term and long-term impacts. The short-term impacts are; increased incidence of morbidity and mortality; cognitive, motor, and verbal development in children is not optimal; and increased healthcare costs. While the long-term impact; Posture that is not optimal as an adult (shorter than usual); Increased risk of obesity and other diseases; The decline in reproductive health; Less than optimal learning capacity and performance during school years; and Low productivity and work capacity (Kemenkes RI, 2018). The nursing goal is to help people achieve quality, holistic health. Implementation of Modeling and Role Modeling Theory is an option in implementing nursing care for children with stunting. “Modeling” is gaining an understanding of the client’s world from the client’s perspective. That is to build a “model” of the client’s worldview. “Role‑Modeling” is based on the assumption that all humans want to interact with others, they want to carry out selected roles in society. Role-Modeling is using the client’s model of the world to plan interventions that meet his or her perceived needs, grow, develop and heal. Role-Modeling requires that we aim to build trust, promote a positive orientation and a sense of control, affirm strengths and set specific mutual goals.

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Recent advances in sensor and platform technologies such as satellite systems, unmanned aerial vehicles (UAV), manned aerial platforms, and ground-based sensor networks have resulted in massive volumes of data is produced and collected about the earth. Processing, managing, and analyzing these data is one of the main challenges in 3D synthetic representation used in modeling and simulation (M&S) of the natural environment. M&S devices, such as flight simulators, traditionally require a variety of different databases to provide a synthetic representation of the world. M&S often requires integration of data from a variety of sources stored in different formats. Thus, for simulation of a complex synthetic environment, such as a 3D terrain model, tackling interoperability among its components (geospatial data, natural and man-made objects, dynamic and static models) is a critical challenge. Conventional approaches used local proprietary data models and formats. These approaches often lacked interoperability and created silos of content within the simulation community. Therefore, open geospatial standards are increasingly perceived as a means to promote interoperability and reusability for 3D M&S. In this paper, the Open Geospatial Consortium (OGC) CDB Standard is introduced. “CDB” originally refers to Common DataBase which is currently considered as a name with no abbreviation in the OGC community. The OGC CDB is an international standard for structuring, modeling, and storing geospatial information required in high performance modeling and simulation applications. CDB defines the core conceptual models, use cases, requirements, and specifications for employing geospatial data in 3D M&S. The main features of the OGC CDB Standard are described as run-time performance, full plug-and-play interoperable geospatial data store, usefulness in 3D and dynamic simulation environment, ability to integrate proprietary and open-source data formats. Furthermore, compatibility with the OGC standards baseline reduces the complexity of discovering, transforming, and streaming geospatial data into the synthetic environment and makes them more widely acceptable to major geospatial data/software producers. This paper includes an overview of OGC CDB version 1.0 which defines a conceptual model and file structure for the storage, access, and modification of a multi-resolution 3D synthetic environment data store. Finally, this paper presents a perspective of future versions of the OGC CDB and what the steps are for humanizing the OGC CDB standard with the other OGC/ISO standards baseline.

The three-dimensional single fin configuration finds application in an intake geometry where the cowl-shock wave interacts with the side-wall boundary-layer. Accurate numerical simulation of such three-dimensional shock/turbulent boundary-layer interaction flows, which are characterized by the appearance of strong crossflow separation, is a challenging task. Reynolds-averaged Navier-Stokes computations using the shock-unsteadiness modified Spalart-Allmaras model is carried out at Mach of 5 at large fin angle of 23^◦. The computed results using the modified model are compared to the standard Spalart-Allmaras model and validated against the experimental data. The focus of work is to implement the modified model and to study the flow physics in detail in the complex region of swept-shock-wave turbulent boundary-layer interaction in terms of the shock structure, expansion fan, shear layer and the surface streamlines. The flow structure is correlated to the wall pressure and skin friction in detail. It is observed that the standard model predicts an initial pressure location downstream of the experiments. The modified model reduces the eddy viscosity at the shock and predicts close to the experiments. Overall, the surface pressure using modified model is predicted accurately at all the locations. The skin friction is under predicted by both the models in the reattachment region and is attributed to the poor performance of turbulence models due to flow laminarization.

A U.S. government health agency conducted epidemiological studies to evaluate whether exposures to drinking water contaminated with volatile organic compounds at U.S. Marine Corps Base Camp Lejeune, North Carolina, were associated with increased health risks to children and adults. These health studies required knowledge of contaminant concentrations in drinking water—at monthly intervals—delivered to family housing, barracks, and other facilities within the study area. Because concentration data were limited or unavailable during much of the period of contamination (1950s–1985), the historical reconstruction process was used to quantify estimates of monthly mean contaminant-specific concentrations. This paper integrates many efforts, reports, and papers into a synthesis of the overall approach to, and results from, a drinking-water historical reconstruction study. Results show that at the Tarawa Terrace water treatment plant (WTP) reconstructed (simulated) tetrachloroethylene (PCE) concentrations reached a maximum monthly average value of 183 micrograms per liter (ug/L) compared to a one-time maximum measured value of 215 ug/L and exceeded the U.S. Environmental Protection Agency’s current maximum contaminant level (MCL) of 5 ug/L during the period November 1957–February 1987. At the Hadnot Point WTP, reconstructed trichloroethylene (TCE) concentrations reached a maximum monthly average value of 783 ug/L compared to a one-time maximum measured value of 1,400 ug/L during the period August 1953–December 1984. The Hadnot Point WTP also provided contaminated drinking water to the Holcomb Boulevard housing area continuously prior to June 1972, when the Holcomb Boulevard WTP came on line (maximum reconstructed TCE concentration of 32 ug/L) and intermittently during the period June 1972–February 1985 (maximum reconstructed TCE concentration of 66 ug/L). Applying the historical reconstruction process to quantify contaminant-specific monthly drinking-water concentrations is advantageous for epidemiological studies when compared to using the classical exposed versus unexposed approach.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

Synthetic Aperture RADAR (SAR) is a radar imaging technique in which the relative motion of the sensor is used to synthesize a very long antenna and obtain high spatial resolution. Standard SAR raw data processing techniques assume uniform motion of the satellite (or aerial vehicle) and a fixed antenna beam pointing sideway orthogonally to the motion path, assumed rectilinear. Despite SAR data processing is a well established imaging technology that has become fundamental in several fields and applications, in this paper a novel approach has been used to exploit coherent illumination, demonstrating the possibility of extracting a large part of the ancillary data information from the raw data itself, to be used in the focusing procedure. In this work an effort has been carried out to try to focus the raw SAR complex data matrix without the knowledge of anyof the parameters needed in standard focusing procedures as Range Doppler (RD) algorithm, ω - K algorithm and Chirp Scaling (CS) algorithm. All the literature references regarding the algorithms needed to obtain a precise image from raw data use such parameters that refer both to the SAR system acquisition geometry and its radiometric specific parameters. In [12], authors introduced a preliminary work dealing with this problem and able to obtain, in the presence of a strong point scatterer in the observed scene, good quality images, if compared to the standard processing techniques. In this work the proposed technique is described and performances parameters are extracted to compare the proposed approach to RD.

This economic evaluation aims to support policy-making on the combined use of pre-exposure prophylaxis (PrEP) with HIV vaccines by evaluating the potential cost-effectiveness of implementation that would support the design of clinical trials for assessment of combined product safety and efficacy. The target study population is a cohort of men who have sex with men (MSM) in the United States. Policy strategies considered include standard HIV prevention, daily oral PrEP, HIV vaccine, and their combination. We constructed a Markov model based on clinical trial data and published literature. We used a payer perspective, monthly cycle length, a lifetime horizon, and a 3% discount rate. We assumed a price of $500 per HIV vaccine series in the base case. HIV vaccines dominated standard care and PrEP. At current prices,PrEP was not cost-effective alone or in combination. A combination strategy had the greatest health benefit but was not cost-effective (ICER=$463,448/QALY) as compared to vaccination alone. Sensitivity analyses suggest a combination may be valuable for higher-risk men with good adherence. Vaccine durability and PrEP drug prices were key drivers of cost-effectiveness. Results suggest that boosting potential may be key to HIV vaccine value.

In March 2020, the World Health Organization declared coronavirus disease 2019 (COVID-19), caused by the novel severe acute respiratory syndrome coronavirus 2, to be a pandemic. Since the declaration, Nigeria economy has been greatly impacted thus resulting in a recession. This paper considers a couple of misconceptions among Nigerian people in the COVID-19 pandemic era thereby causing the spread of the novel virus and hence making the situation difficult for the government to handle. In particular, we discuss the first and second waves of the pandemic as it affects the Nigerian people. The impact of the pandemic on animals and the role of mathematical epidemiologists in combatting the spread is discussed herein. We give some recommendations that could be adopted by the government and the good people of Nigeria to reduce the further spread of the virus.

As our understanding of the thalamocortical system deepens, the questions we face become more complex. Their investigation requires the adoption of novel experimental approaches complemented with increasingly sophisticated computational modeling. In this review, we take stock of current data and knowledge about the circuitry of the somatosensory thalamocortical loop in rodents, discussing common principles across modalities and species whenever appropriate. We review the different levels of organization, including the cells, synapses, neuroanatomy, and network connectivity. We provide a complete overview of this system that should be accessible for newcomers to this field while nevertheless being comprehensive enough to serve as a reference for seasoned neuroscientists and computational modelers studying the thalamocortical system. We further highlight key gaps in data and knowledge that constitute pressing targets for future experimental work. Filling these gaps would provide invaluable information for systematically unveiling how this system supports behavioral and cognitive processes.

Today massive amounts of sequenced metagenomic and -transcriptomic data from different ecological niches and environmental locations are available. Scientific progress depends critically on methods that allow extracting useful information from the various types of sequence data. Here, we will first discuss types of information contained in the various flavours of biological sequence data, and how this information can be interpreted to increase our scientific knowledge and understanding. We argue that a mechanistic understanding is required to consistently interpret experimental observations, and that this understanding is greatly facilitated by the generation and analysis of dynamic mathematical models. We conclude that, in order to construct mathematical models and to test mechanistic hypotheses, time-series data is of critical importance. We review diverse techniques to analyse time-series data and discuss various approaches by which time-series of biological sequence data was successfully used to derive and test mechanistic hypotheses. Analysing the bottlenecks of current strategies in the extraction of knowledge and understanding from data, we conclude that combined experimental and theoretical efforts should be implemented as early as possible during the planning phase of individual experiments and scientific research projects.

By installing FBG sensors on the geogrids, smart geogrids can both reinforce and monitor the stability for geogrid-reinforced slopes. In this paper, a geogrid-reinforced sand slope model test was conducted in the laboratory and fiber Bragg grating (FBG) sensing technology is used to measure the strain distribution of the geogrid. Based on the model test, the performance of the reinforced soil slope is simulated by finite element software Midas-GTS, and the stability of the reinforced soil slope is analyzed by strength reduction method. The relationship between the geogrid strain and safety factor is set up. The results indicate that the measured strain and calculated results agree very well. The geogrid strain measured by FBG sensor can be applied to evaluate the stability of geogrid-reinforced sand slopes.

Synesthesia is a psychological phenomenon where sensory signals become mixed. Input to one sensory modality produces an experience in a second, unstimulated modality. In “grapheme-color synesthesia”, viewed letters and numbers evoke mental imagery of colors. The study of this condition has implications for increasing our understanding of brain architecture and function, language, memory and semantics, and the nature of consciousness. In this work, we propose a novel application deep learning to model perception in grapheme-color synesthesia. Achromatic letter images, taken from database of handwritten characters, are used to induce synesthesia. Results show the model learns to accurately create a colored version of the inducing stimulus, according to a statistical distribution from experiments on a sample population of grapheme-color synesthetes. The spontaneous, creative mental imagery characteristic of the synesthetic perceptual experience is reproduced by the model. A model of synesthesia that generates testable predictions on brain activity and behavior is needed to complement large scale data collection efforts in neuroscience, especially when articulating simple descriptions of cause (stimulus) and effect (behavior). The research and modeling approach reported here begins to address this need.

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

The goal of the study was to assess the farmers’ acceptance of three sustainable production strategies, namely ‘Agro-forestry’, ‘Alternative protein source’ and ‘Prolonged maternal feeding’. Data on the acceptance of these strategies were collected by a survey of dairy farmers in six EU countries (AT, BE, DK, FI, IT, UK). An extended version of the Technology Acceptance Model (TAM) was applied by means of Structural Equation Modelling to testing various hypotheses on attitudes and intentions of dairy farmers towards these novel production strategies, as well as the influence of organic practices and collaborative behaviours along the supply chain. We found that the most preferred strategy - across all countries - was soy substitution by alternative protein sources. We also found that the intention to adopt a sustainable production strategy may derive from the influence of opinions (and behaviours) of relevant others, showing the role of interactions among farmers and other stakeholders in the adoption of innovations. Finally, the perceived usefulness of all investigated strategies is higher for organic farmers, while collaborative patterns reduce the impact of subjective norm on usefulness and overall acceptance. Our findings should encourage policy makers to consider the important role of supply chain management practices, including collaboration, to enhance the sustainability of dairy farming systems.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

Humans may be exposed to microbial pathogens at recreational beaches via environmental sources, such as water, sand, and aerosols. Although infectious disease risk from exposure to waterborne pathogens has been an active area of research for decades, sand is a relatively unexplored reservoir of pathogens and fecal indicator bacteria (FIB). Beach sand and water habitats provide unique advantages and challenges to pathogen introduction, growth, and persistence, as well as continuous exchange between habitats. Models of FIB and pathogen fate and transport in sandy beach habitats can help predict the risk of infectious disease from recreational water use, but filling knowledge gaps such as decay rates and potential for microbial growth in beach habitats is necessary for accurate modeling. Climatic variability, whether natural or anthropogenically-induced, adds complexity to predictive modeling, but may increase human exposure to waterborne pathogens via extreme weather events, warming of water bodies and sea level rise in many regions. The popularity of human recreational beach activities, combined with predicted climate change scenarios, could amplify the risk of human exposure to pathogens and related illnesses. Other global change trends such as increased population growth and urbanization are expected to exacerbate contamination events and the predicted impacts of increasing levels of waterborne pathogens on human health. Such changes will alter microbial population dynamics in beach habitats, and will consequently affect the assumptions and relationships used in population models and quantitative microbial risk assessment (QMRA). Here, we discuss the literature on microbial population and transport dynamics in sand-water continuum habitats at beaches, how these dynamics can be modeled, and how climate change and other anthropogenic influences (e.g., land use, urbanization) should be considered when using and developing more holistic, beachshed-based models.

Aim of this research paper is to introduce a novel method of hybrid orthodontic tooth-borne distalizer treatment of class II malocclusion by using 3D printed biocompatible personalized distalizer. Explains 3D designing, printing and clinical application of individualized biocompatible medical device dedicated for orthodontic teeth distalization. Compares such distalizer manufactured from two different biocompatible photopolymers (white and transparent). Evaluates their clinical performance and also patients’ aesthetical perception. Clinical part includes comparison of treatment debonding on the set of 12 complete orthodontic treatments with uni-lateral class II malocclusion managed with hybrid approach (CAT-Invisalign with 3D printed distalizer). Paper offers an evaluation of the personalized distalizer functioning in regard to current publications and comparison to conventional prefabricated alternatives like Carriere® Distalizer™ appliance. Results showed no significance of material differences on clinical performance of such individualized distalizers. Research showed preference of patients towards transparent biocompatible photopolymer instead of white A2 shade.

Social media and other web 2.0 tools have provided users the platform to interact and also disclose personal information not only with their friends and acquaintances, but also with relative strangers with unprecedented ease. This has enhanced the ability of people to share more about themselves, their families, and their friends through a variety of media including text, photo, and video, thus developing and sustaining social and business relationships. The purpose of the paper is to identify the factors that predict self-disclosure on social networking sites within the Ghanaian context. Data was collected from 452 students in three leading universities in Ghana and analyzed with Partial Least Square-Structural Equation Modeling. Results from the study revealed that all variables in the proposed model with the exception of interaction and perceived control were significant predictors of self-disclosure with privacy risk being the most significant predictor. In all, the model accounted for 54.6 percent of the variance in self disclosure. The implications and limitations of the current study are discussed and directions for future research proposed.

Choosing the optimal location for a city based on sound environmental geomorphology planning is of the utmost importance to achieving environmental sustainability, as it can spare the State and other decision-making entities a great deal of stress in the long run. GIS offers great potential for environmental planners to choose the most appropriate places for the cities of the future, especially when coupled with environmental geomorphological analyses. The State of Kuwait seeks sustainable development through the implementation of clear and specific urban plans, some of which suffer from a severe lack of geomorphological and spatially based environmental planning. This study aims to: 1) Conduct suitability modelling for establishing new cities in Kuwait, 2) Assess the current 2005-2030 urban plan, and 3) Propose possible recommendations and solutions for potential urban problems. The study relies on integrating several methods to devise a framework that will aid researchers and decision-makers in selecting optimal locations for built structures based on analysis and modelling (e.g., digital elevation model, geologic mapping, geomorphology, natural hazards, heritage/archaeological sites, military areas, oil fields, soils). Using this methodology in choosing city sites contributes to achieving sustainable development, reducing city problems, saving countries’ budgets, and saving lives. Results from this study enhance understanding of how environmental geomorphology, when combined with GIS, can be harnessed to achieve sustainable urban development in the Arabian Gulf countries and other desert countries.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

A finite-difference approach with non-uniform meshes was presented for simulating magnetotelluric responses in 2D structures. We presented the formulation of this scheme and gave some sights into its successful implementation, and compared finite-difference solution with known numerical results and simple analytical solutions. First, a homogeneous half-space model was tested and the finite-difference approach can provide very good accuracy for 2D magnetotelluric modeling. Then we compared to the analytical solutions for the two-layered model, the relative errors of the apparent resistivity and the impedance phase were both increased when the frequency was increased. In the end, we compare our finite-difference simulation results with COMMEMI 2D-0 model with the finite-element solutions. Both results are in close agreement to each other. These comparisons confirm the validity and reliability of our finite-difference algorithm.

Manufacturing organizations shall recognize sustainability as a business occasion to capitalize on, rather than an undesirable pressing situation. Still, empirical evidence shows that this opportunity is hard to capture and communicate in global strategic decisions, through planning by tactical management, to daily operational activities. This paper systematically reviews the modeling challenges at the crossroad of value and sustainability decisions making, spotlighting methods and tools proposed in literature to link sustainability to customer value creation at strategic, tactical and operational level. While statistical results show that the topic of sustainability and value modeling is trending in literature, findings from content analysis reveal that recent attempts to promote a value-based view in the sustainability discussion remain at a strategic level, with most of the proposed indicators being suited for managerial decision-making. The lack of support at operational level points to the opportunity of cross-pollinating sustainability research with value-centered methodologies originating from the aerospace sector. The Value Driven Design framework is proposed as main hub from which to derive models supporting engineers and technology developers in the identification of win-win-win situations, where sustainable improvements are aligned with business advantages.

Selective laser melting (SLM) is one of the widely used techniques in metallic additive manufacturing, in which high-density laser powder is utilized to selectively melting layers of powders to create geometrically complex parts. Temperature distribution and molten pool geometry directly determine the balling effect, and concentrated balling phenomenon significantly deteriorates surface integrity and mechanical properties of the part. Finite element models have been developed to predict temperature distribution and molten pool geometry, but they were computationally expensive. In this paper, the three-dimensional temperature distributions are predicted by analytical models using point moving heat source and semi-ellipsoidal moving source respectively. The molten pool dimensions under various process conditions are obtained from the three-dimensional temperature predictions and experimentally validated. Ti-6Al-4V alloy is chosen for the investigation. Good agreements between the predictions and the measurements are observed. The presented models are also suitable for other metallic materials in the SLM process.

Differential equation models to understand interaction between plant and nutrient solution are presented. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient along the cell membrane. It establishes electrical field with Nernst potential to make positively charged ions outside the cell membrane flow into the root cell. Anion influx is also modulated by H+ ion concentration because plant root cell absorbs negatively charged particles with symport. If an anion collides with H+ cell to make net charge as neutral, at symport channel, it can flow through. In this paper, mathematical models for cation and anion absorption are introduced. Cation absorption model was induced from Ohm's law combined with Goldman's equation. Anion absorption model is similar to chemical reaction rate model. Both models have physiological terms influenced by gene expression pattern, species or phenotypes. Cation model also includes terms for ion's kinetic and electrical properties, growth of plant and interaction between the root and the surroundings. Simulation for 20 different sets of coefficients showed that the physiology-related coefficient has important role on nutrition absorption tendencies of plants.

The Agricultural Policy/Environmental eXtender (APEX) model is widely used for evaluating agricultural conservation efforts and their effects on soil and water. A key component of APEX application in Korea is simulating water quality impacts of rice paddies because rice agriculture claims the largest cropland area in the country. In this study, a computational module called APEX-Paddy is developed to simulate water quality with considering pertinent paddy management practices such as puddling, flood irrigation management. Data collected at two experimental paddy sites in Korea were used to calibrate and validate the model. Results indicate that APEX-Paddy performs well in predicting runoff discharge rate and nitrogen yield while the original APEX highly overestimates runoff rates and nitrogen yields on large storm events. With APEX-Paddy, simulated and observed flow and mineral nitrogen yield (QN) are found to be highly correlated after calibration (Nash & Sutcliffe Efficiency (NSE) = 0.87 and Percent Bias (PBIAS) = −14.6% for flow; NSE = 0.68 and PBIAS = 2.1% for QN). Consequently, the APEX-Paddy showed a greater accuracy in flow and QN prediction than the original APEX modeling practice using the SCS-CN method.

Recent technological improvements have made abundant changes in construction industry. In specific, some technical applications, such as Building Information Modeling (BIM) opens up many possibilities. Some studies have articulated the use of BIM and its advantages in construction, but most of them are theoretical, not practical. This study is to provide an insight to such obstacles in BIM research. By investigating a real project that could utilize BIM in planning and construction phases, the authors try to investigate a possible outline of advantages in BIM implementation. The study area was set to a railway construction site in South Korea. The site covers a multiple railway tracks, stations, telecommunication facilities, infrastructure facilities, railway structures, and so numerous. In the site, the authors have identified 12 errors in 7 projects that could be prevented if BIM was utilized before the construction. The total upfront costs required to provide a BIM for 7 projects were $116,348. On the other hand, the total costs required to fix the errors in 7 projects were $166,486. This can be regarded as the benefits of using BIM because if BIM was implemented then the associated errors are easily replaced. Therefore, the benefit-cost ratio can be estimated as 1.32 for one-month delay and 1.36 for a three-month delay.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

Subsurface temperature is the key parameter in geothermal exploration. An accurate estimation of the reservoir temperature is of high importance and usually done either by interpolation of borehole temperature measurement data or numerical modeling. However, temperature measurements at depths which are of interest for deep geothermal applications (usually deeper than 2 km) are generally sparse. A pure interpolation of such sparse data always involves large uncertainties and usually neglects knowledge of the 3D reservoir geometry or the rock and reservoir properties governing the heat transport. Classical numerical modeling approaches at regional scale usually only include conductive heat transport and do not reflect thermal anomalies along faults created by convective transport. These thermal anomalies however are usually the target of geothermal exploitation. Kriging with trend does allow including secondary data to improve the interpolation of the primary one. Using this approach temperature measurements of depths larger than 1,000 m of the federal state of Hessen/Germany have been interpolated in 3D. A 3D numerical conductive temperature model was used as secondary information. This way the interpolation result reflects thermal anomalies detected by direct temperature measurements as well as the geological structure. This results in a considerable quality increase of the subsurface temperature estimation.

The bottleneck in creating dynamic models of biological networks and processes often lies in estimating unknown kinetic model parameters from experimental data. In this regard, experimental conditions have a strong influence on parameter identifiability and should therefore be optimized to give the maximum information for parameter estimation. Existing model-based design of experiment (MBDOE) methods commonly rely on the Fisher Information Matrix (FIM) for defining a metric of data informativeness. When the model behavior is highly nonlinear, FIM-based criteria may lead to suboptimal designs since the FIM only accounts for the linear variation of the model outputs with respect to the parameters. In this work, we developed a multi-objective optimization (MOO) MBDOE, where model nonlinearity was taken into consideration through the use of curvature. The proposed MOO MBDOE involved maximizing data informativeness using a FIM-based metric and at the same time minimizing the model curvature. We demonstrated the advantages of the MOO MBDOE over existing FIM-based and other curvature-based MBDOEs in an application to the kinetic modeling of fed-batch fermentation of Baker's yeast.

The purpose of interdisciplinary communication during the early architectural design stage is to achieve the early integration of knowledge in different professional fields, which can help architects to choose correct design development strategies during the early architectural design stage. However, because there is too little information at the early design stage, and design solutions are still rapidly changing and developing, the uncertainties at this stage make it difficult for consultants in other disciplines to provide their views and analysis. In spite of this situation, the emergence of generative modeling is changing design procedures and methods of communication and cooperation for architectural teams, and has brought about a shift in the way architects transmit design information from "what" (declarative information) to "how" (procedural information). Generative modeling is like an aircraft's dashboard: It can provide a basis for interdisciplinary communication, provide interdisciplinary knowledge packages, and bring about a shift in interdisciplinary communication that will reduce the architectural team's communication needs and cost. This study uses a real design case to show the feasibility of generative modeling. Employing generative modeling as a basis, architects can enhance the efficiency of design change and multi-disciplinary communication during the early design stage, integrate specialized knowledge in relevant fields, use this knowledge to formulate design criteria for the next stage, and effectively transmit design decisions. As a consequence, the changes to the cost structure of design revisions and communication between different disciplines has initiated a paradigm shift toward multi-disciplinary communication in architectural design.

In a computing context, cybersecurity is undergoing massive shifts in technology and its operations in recent days, and data science is driving the change. Extracting security incident patterns or insights from cybersecurity data and building corresponding data-driven model, is the key to make a security system automated and intelligent. To understand and analyze the actual phenomena with data, various scientific methods, machine learning techniques, processes, and systems are used, which is commonly known as data science. In this paper, we focus and briefly discuss cybersecurity data science, where the data is being gathered from relevant cybersecurity sources, and the analytics complement the latest data-driven patterns for providing more effective security solutions. The concept of cybersecurity data science allows making the computing process more actionable and intelligent as compared to traditional ones in the domain of cybersecurity. We then discuss and summarize a number of associated research issues and future directions. Furthermore, we provide a machine learning-based multi-layered framework for the purpose of cybersecurity modeling. Overall, our goal is not only to discuss cybersecurity data science and relevant methods but also to focus the applicability towards data-driven intelligent decision making for protecting the systems from cyber-attacks.

In this study, we present case studies to explore the dynamics of implementation and maintenance of health interventions. We analyze how specific interventions are built and eroded, how the building and erosion mechanisms are interconnected, and why we can see significantly different erosion rates across otherwise similar organizations. We use multiple comparative obesity prevention case studies to provide empirical information on the mechanisms of interest, and use qualitative systems modeling to integrate our evolving understanding into an internally consistent and transparent theory of the phenomenon. Our preliminary results identify reinforcing feedback mechanisms, including design of organizational processes, motivation of stakeholders, and communication among stakeholders, which influence implementation and maintenance of intervention components. Over time, these feedback mechanisms may drive a wedge between otherwise similar organizations, leading to distinct configurations of implementation and maintenance processes.

Mortarless refractory masonry structures are widely used in the steel industry for the linings of many high-temperature industrial applications including steel ladle. The design and the optimization of these components require accurate numerical models that consider the presence of joints as well as joints closure and opening due to cyclic heating and cooling. The present work reports on the formulation, numerical implementation, validation, and application of homogenized numerical models for simulation of refractory masonry structures with dry joints. The validated constitutive model has been used to simulate a steel ladle and to analyze its transient thermomechanical behavior during a typical thermal cycle of steel ladle. 3D solution domain, enhanced thermal and mechanical boundary conditions have been used. Parametric studies to investigate the impact of joints thickness on the thermomechanical response of the ladle have been carried out. The results clearly demonstrate that the thermomechanical behavior of mortarless masonry is orthotropic nonlinear due to gradual closure and reopening of joints with the increase and decrease of temperature. Also, resulting thermal stresses increase with the increase of temperature and decrease with the increase of joints thickness.

External quantum efficiency of industrial-grade green InGaN light-emitting diodes (LEDs) has been measured in a wide range of operating currents at various temperatures from 13 K to 300 K. Unlike blue LEDs, the efficiency as a function of current is found to have a multi-peak character, which could not be fitted by a simple ABC-model. This observation correlated with splitting of LED emission spectra into two peaks at certain currents. The characterization data are interpreted in terms of non-uniformity of the LED active region, which is tentatively attributed to extended defects like V-pits. We suggest a new approach to evaluation of temperature-dependent light extraction and internal quantum efficiencies taking into account the active region non-uniformity. As a result, the temperature dependence of light extraction and internal quantum efficiencies have been evaluated in the temperature range mentioned above and compared with those of blue LEDs.

A copula is a useful tool for constructing bivariate and/or multivariate distributions. In this article, we consider a new modified class of (Farlie-Gumbel-Morgenstern) FGM bivariate copula for constructing several dierent bivariate Kumaraswamy type copulas and discuss their structural properties, including dependence structures. It is established that construction of bivariate distributions by this method allows for greater flexibility in the values of Spearman's correlation coefficient rho,  and Kendall's tau . For illustrative purposes, one representative data set is utilized to exhibit the applicability of these proposed bivariate copula models.

Restoration experience is a positive response against the ever-increasing problem of stress. It is recovery of attentional capacity, clearing random thoughts and feelings of relaxation and calmness. Although there is a body of research on investigating the impact of open green space characteristics on psycho- logical restoration through attention restoration theory and supportive environment theory, there is little knowledge on how the interaction among these characteristics could promote restorative outcomes. To address this problem, using Perceived Sensory Dimension (PSD) for open green space qualities and Perceived Restorativeness (PR) as the property of restorative environment, this study assessed the extent to which the PSD and PR impact on restoration experience. Using 444 screened surveys, a Partial Least Square Structural Equation Model (PLS-SEM) was developed and the validity and reliability of it, was demonstrated. Extensive analysis of the results showed how environmental qualities can promote restoration experience using a sample of university students. These results provide information for landscape architecture and planning researchers to promote the development of open spaces as a resource of psychological restoration and stress relief.

COVID-19 has created anxiety not only in individuals but also in health organizations, and countries worldwide. Not a single industry is left un-influenced and loss is being estimated in billions of dollars. The widespread of this pandemic disease has challenged researchers all over the world. Some of the researchers are working to invent its cure while, others are applying computing technologies to stop its spread, by analyzing and identifying patterns for prediction and forecasting. This is by no doubt the hottest area of research for the last 100 years. This survey has targeted the research published in computing sub-domains to combat the pandemic. The survey has clustered the scientific efforts into logical groups: surveillance, metrological effects, social media analytics, image processing and business and economy, analysis and modeling. It will serve as a leading source for the followings: researchers who want to identify what has been achieved in different computing sub-domains, those who need fresh authenticated datasets openly accessible for different research contexts and what are future directions in this area of research. The findings of analysis and modeling can be also useful for government agencies who want to set priorities and formulate policies.

Energy storage systems (ESS) are penetrating into various sections of power system through different applications. ESS can be used either as a buffer for intermittent renewable energy sources or as a stand-alone distributed storage for load shifting. ESS use different types of storage devices such as lead-acid batteries, lithium ion batteries, flow batteries, and super-capacitors. Hybrid ESS consisting of few types of storage devices are also common in practice. Determining the load demand of such ESSs at various instances (charging profile) accurately is indispensable in most of the cases. Capacity loss is common phenomenon that occurs in all types of storage devices because of ageing. Capacity loss has to be accounted while determining the charging profile of storage devices for better accuracy. Data-driven modeling is an attractive approach for determining the load demand of ESS due to the availability of valuable data from smart grid technologies. In this paper, the application of different types of data-driven models to predict the current charging profile of the ESS based on previous charging profiles is examined. The proposed method can leverage on the existing data from smart grid and is a black box modeling approach.

Mathematical models of cognition measure individual differences in cognitive processes, such as processing speed, working memory capacity, and executive functions, that may underlie general intelligence. As such, cognitive models allow identifying associations between specific cognitive processes and tracking the effect of experimental interventions aimed at the enhancement of intelligence on mediating process parameters. Moreover, cognitive models provide an explicit theoretical formalization of theories regarding specific cognitive process that may help overcoming ambiguities in the interpretation of fuzzy verbal theories. In this paper, we give an overview of the advantages of cognitive modeling in intelligence research and present models in the domains of processing speed, working memory, and selective attention that may be of particular interest for intelligence research. Moreover, we provide guidelines for the application of cognitive models in intelligence research, including data collection, the evaluation of model fit, and statistical analyses.

A car-roof photovoltaic has an enormous potential to change our society. With this technology, 70% of the personal car can run by the solar energy collected by the solar panel on its car-roof. Unfortunately, it is not a simple extension of the conventional photovoltaic technology. This paper list what we need to do for realizing the future that majority of the personal cars run by renewable solar energy, after clarification of the difference from the conventional photovoltaic technology. In addition to the technological development, the standardization of this innovative technology will be important, and the list was made highlighting the standardization.

Incorporating linear-scanning MEMS micromirrors into Fourier transform spectral acquisition systems can greatly reduce the size of the spectrometer equipment, making portable Fourier transform spectrometers (FTS) possible. How to minimize the tilting of the MEMS mirror plate during its large linear scan is a major problem in this application. In this work, an FTS system has been constructed based on a biaxial MEMS micromirror with a large piston displacement of 180 μm, and a biaxial H∞ robust controller is designed. Compared with open-loop control and PID closed-loop control, H∞ robust control has good stability and robustness. The experimental results show that the stable scanning displacement reaches 110.9 μm under the H∞ robust control, and the tilting angle of the MEMS mirror plate in that full scanning range falls within ±0.0014°. Without control, the FTS system cannot generate meaningful spectra. In contrast, the FTS yields a clean spectrum with an FWHM spectral linewidth of 96 cm-1 under the H∞ robust control. Moreover, the FTS system can maintain good stability and robustness under various driving conditions.

SGLT2 inhibitors act to induce glucosuria and have been shown to be efficacious in the treatment of type II diabetes mellitus but have also been shown to positively affect cardiovascular conditions and some benefitting kidney function. SGLT2i have shown to be effective in more advanced conditions but may eventually be a treatment in more general metabolic dysfunction. Metabolic syndrome is a clinical diagnosis for establishing risk for ischemic heart disease and diabetes. The prevalence of type II diabetes mellitus, heart disease, and severe vascular events steadily increased over recent decades. In addition to the established benefits of diet and exercise, SGLT2 inhibitor therapy may be able to aid in the treatment of metabolic syndrome from its proven cardiovascular and anti-hyperglycemic benefits. Pharmacologic modeling in canines is also considered, as they present with similar diagnoses and offer a model that shares many of the characteristics of humans in metabolic dysfunction.

Hydrological modeling allows us to make a comprehensive assessment of the interaction between dynamics of the hydrological cycle, climate conditions, and land use. These modeling results are relevant in water resources management field. We use TopModel (TOPography based hydrological MODEL for the hydrological modeling of an area of 17 000 km² in the Middle Magdalena Valley (MMV), a tropical basin located in Colombia. This study is located in the intertropical convergence zone (ITCZ) which is characterized by special meteorological conditions and fast water fluxes over the year. This area has been subjected to significant land use changes, as a result of intense economic activities, e.g., agriculture, hydropower energy and oil & gas production (Avellaneda, 2003). The proposed model is based on a record of 12 years of: i.) daily precipitation data from observed gauges, ii.) daily evapotranspiration data from temperature data and iii.) daily streamflow data as observed data. A calibration process was performed using data from 2000 to 2008, and a validation was performed with data from 2009 to 2012. The Nash-Sutcliffe coefficient was used as an objective function to assess the quality of these processes (values of this metric are between 0.74 and 0.73 respectively, for model calibration and validation). The results show us an adequate performance of the model in areas of the tropical region and allow us to analyze the relationship between water storage capacity in the soils of the area with subsurface runoff. This conclusion is consistent with the characteristics of the region. The calibrated model provides an idea about the hydrological functioning of the basin and estimates an approximation of the groundwater recharge in the region. The estimation of the recharge is important to quantify the interaction of surface water and groundwater, especially during the dry season, due to its importance in the analysis of scenarios with climate variability.

Copulas are useful tools for modeling the dependence structure between two or more variables. Copulas are becoming a quite flexible tool in modeling dependence among the components of a multivariate vector, in particular to predict losses in insurance and finance. In this article, we study the dependence structure of some well-known real life insurance data (with two components mainly) and subsequently identify the best bivariate copula to model such a scenario via VineCopula package in R. Associated structural properties of these bivariate copulas are also discussed.

Estimation of core and surface temperature is one of the crucial functionalities of the lithium-ion Battery Management System (BMS) towards providing effective thermal management, fault detection and operational safety. While, it is impractical to measure core temperature using physical sensors, implementing a complex estimation strategy in on-board low-cost BMS is challenging due to high computational cost and the cost of implementation. Typically, a temperature estimation scheme consists of a heat generation model and a heat transfer model. Several researchers have already proposed ranges of thermal models having different levels of accuracy and complexity. Broadly, there are first-order and second-order heat capacitor-resistor-based thermal models of lithium-ion batteries (LIBs) for core and surface temperature estimation. This paper deals with a detailed comparative study between these two models using extensive laboratory test data and simulation study to access suitability in online prediction and onboard BMS. The aim is to guide whether it’s worth investing towards developing a second-order model instead of a first-order model with respect to prediction accuracy considering modelling complexity, experiments required and the computational cost. Both the thermal models along with the parameter estimation scheme are modelled and simulated using MATLAB/Simulink environment. Models are validated using laboratory test data of a cylindrical 18650 LIB cell. Further, a Kalman Filter with appropriate process and measurement noise levels are used to estimate the core temperature in terms of measured surface and ambient temperatures. Results from the first-order model and second-order models are analyzed for comparison purposes.

As a result of rapid population growth, an exponentially growing human population, and industrial expansion, it has become increasingly difficult to manage municipal solid wastes throughout the world. Decentralized waste management systems have created difficult situations in developing countries such as Malaysia. Wastes generated in the country, due to various cultural, social, and religious activities, organic and contributing to environmental pollution (air, water, and soil) and human health troubles. A questionnaire survey was participated by 220 construction professionals in Malaysia using structured and semi-structured methods. The framework was assessed using A partial least square structural equation modeling (PLS-SEM) to target sustainable development goals (SDG). Statistical analysis results indicate a significant effect between SCW management, since(r(270)=.687, P<0.001). Improving factors has strong relationship with SCW management, since(r(270)=.723, P<0.001). The mediation results also suggested a significant indirect positive effect of improving factors drivers on SCW management through policy-related factors sinceβ=0.688, t=8.254, P<0.001, 95% CI for β=0.536,0.866. Finally, policy-related factors construct has a strong relationship with SCWM) management, since(r(270)=.811, P<0.001) With the R Square of 0.787 and 0.785. The developed framework can improve construction waste management in the construction industry and enhance construction waste management to achieve global sustainable development goals. The findings show that one of the most critical issues of enhancing profitability is using preventive policies to reduce construction waste. This study could guide construction industry stakeholders in identifying the different waste management features during a building project's construction and design stage

Dietary factors are one of the risk factors that can impact the brain chemistry, which leads to mental distress. Based on our data mining approach, we found that mental distress in men is associated with eating unhealthy food. Our aim in this paper is to apply results from our big data analytics approach to inform system dynamics (SD) modeling to investigate the causal relationships between brain structures, nutrients from food and dietary supplements, and mental health. We perform descriptive analysis based on a large data set to estimate the SD modeling parameters. Finally, we calibrate the model towards a time series data collected for individuals on their dietary and distress patterns. The results reveal that bridging these different methodologies leads to further insights from the SD model and decreases the error of calibrated parameter values. Future research is needed to validate our initial results for investigating the relationship between mental distress and dietary intake.

: The cyber-physical gap (CPG) is the difference between the 'real' state of the world and the way the system perceives it. This discrepancy often stems from the limitations of sensing and data collection technologies and capabilities, and is an inevitable issue in any cyber-physical system (CPS). Ignoring or misrepresenting such limitations during system modeling, specification, design, and analysis can potentially result in systemic misconceptions, disrupted functionality and performance, system failure, severe damage, and potential detrimental impacts on the system and its environment. We propose CPG-Aware Modeling & Engineering (CPGAME), a conceptual model-based approach for capturing, explaining, and mitigating the CPG, on top of and in sync with the conventional system model, and as an inherent systems engineering activity. This approach enhances the systems engineer’s ability to cope with CPGs, mitigate them by design, and prevent erroneous decisions, actions, and hazardous implications. CPGAME is a generic, conceptual approach, specified and demonstrated with Object Process Methodology (OPM). OPM is a holistic conceptual modeling paradigm for multidisciplinary, complex, dynamic systems, which is also ISO-19450. We analyze the 1979 Three Miles Island 2 nuclear accident as a prime example of the disastrous consequences of unmitigated CPGs in complex systems.

Naturally occurring small molecules include a large variety of natural products from different sources that have confirmed activity against epigenetic targets. In this work we review chemoinformatic, molecular modeling and other computational approaches that have been used to uncover natural products as inhibitors of DNA metiltransferases, a major family of epigenetic targets with significant potential for the treatment of cancer and several other diseases. Examples of these computational approaches include docking, similarity-based virtual screening, and pharmacophore modeling. It is also commented the chemoinformatic-based exploration of the chemical space of naturally occurring compounds as epigenetic modulators which may have significant implications in epigenetic drug discovery and nutriepigenetics.

COVID-19 is a novel severe acute respiratory syndrome coronavirus. Presently, there is no effective treatment for COVID-19. As part of the worldwide efforts to find efficient therapies and preventions, it has been reported the crystalline structure of the SARS-CoV-2 main protease Mpro (also called 3CL^pro) bound to a synthetic inhibitor which represents a major druggable target. The druggability of Mpro could be used for discovering drugs to treat coronavirus disease 2019. It was carried out a multi-level computational study to evaluate the potential anti-viral properties of the components of the medicinal herb Uncaria tomentosa (Cat´s claw) focusing on the inhibition of M^pro. The in-silico approach starts with protein-ligand docking of 26 Cat’s claw key components followed by ligand pathway calculations, molecular dynamics simulations and MM-GBSA calculation of the free energy of binding for the best docked candidates. The structural bioinformatics approaches led to the identification of three bioactive compounds of Uncaria tomentosa (Speciophylline, Cadambine and Proanthocyanidin B2) with potential therapeutic effects by strong interaction with 3CLpro. Additionally, in silico drug-likeness indices for these components were calculated and show good predicted therapeutic profiles of these phytochemicals. Our findings suggest the potential effectiveness of Cat's claw as complementary and/or alternative medicine for COVID-19 treatment.

The highest efficiency solar cell won in the efficiency race does not always give the most excellent annual energy yield in the real world solar condition that the spectrum is ever-changing. The study of the radiative coupling of the concentrator solar cells implied that the efficiency could increase by the recycle of the radiative recombination generated by the surplus current in upper junction. Such configuration is called by a super-multi-junction cell. We expanded the model in the concentrator solar cell to non-concentrating installation. It was shown that this super-multi-junction cell configuration was found robust and can keep the maximum potential efficiency (50 % in realistic spectrum fluctuation) up to 10 junctions. The super-multi-junction cell is also robust in the bandgap engineering of each junction. Therefore, the future multi-junction may not be needed to tune the bandgap for matching the standard solar spectrum, as well as relying upon artificial technologies like ELO (Epitaxial lift-off), wafer-bonding, mechanical-stacking, and reverse-growth, but merely uses up-right and lattice-matching growth technologies. We have two challenging techniques; one is the optical cap layer that may be the directional photon coupling layer in the application of the photonics technologies, and another is the high-quality epitaxial growth with almost 100 % of the radiative efficiency.

The State of Kuwait seeks sustainable development through implementation of clear and specific urban plans, some of which suffer from a severe lack of geomorphological and spatially-based environmental planning, such as the use of geographic information systems (GIS). Choosing the optimal location for a city based on sound environmental planning is of the utmost importance to achieving environmental sustainability, as it can spare the State and other decision-making entities a great deal of stress in the long run. GIS, in particular, offers great potential for the environmental planner and decision-maker to choose the most appropriate places for the cities of the future, especially when coupled with geomorphological analyses. To achieve the Vision of Kuwait 2035, one of the State’s planning objectives focuses on Urban Planning for the Establishment of Environmental Cities that Achieve (UPEECA) environmental sustainability criteria. To gain a more holistic analysis related to the Vision, this study aims to: 1) Conduct suitability modelling for establishing new cities in Kuwait, 2) Assess the current 2005-2030 urban plan, and 3) Propose possible recommendations and solutions for potential urban problems. The study relies on integrating several methods to devise a framework that will aid researchers and decision-makers in selecting optimal locations for built structures based on analysis and modelling (e.g., digital elevation model, geologic mapping, geomorphology, natural hazards, heritage/archaeological sites, military areas, oil fields, soils)

Liquid propellants are fast becoming attractive for pulsed plasma thrusters due to their high efficiency and low contamination issues. However, the complete plasma interaction and acceleration processes are still not very clear. Present paper develops a multi-layer numerical model for liquid propellant PPTs. The model proposes a possible acceleration mechanism for liquid fed pulsed plasma thrusters and accurately predicts the propellant utilization capabilities and estimations for the fraction of propellant gas that is completely ionized and accelerated to high exit velocities. Validation of the numerical model and the assumptions on which the model is based on is achieved by comparing the experimental results from two different liquid-fed thrusters developed at the University of Tokyo. Results show 50% of liquid propellant injected is completely ionized and accelerated to high exit velocities (> 50Km/s), whereas, neutral gas contribute to only 7% of the total specific impulse and accelerated to low exit velocity (< 4Km/s). The model shows an accuracy up-to 92%. Optimization methods are briefly discussed to ensure efficient propellant utilization and performance. The model acts as a tool to understand the background physics and to optimize the performance for liquid-fed PPTs.

The capability to avoid other air traffic is a fundamental component of the layered conflict management system to ensure safe and efficient operations in the National Airspace System. The evaluation of systems designed to mitigate the risk of midair collisions of manned aircraft are based on large-scale modeling and simulation efforts and a quantitative volume defined as a near midair collision (NMAC). Since midair collisions are difficult to observe in simulation and are inherently rare events, basing evaluations on NMAC enables a more robust statistical analysis. However, an NMAC and its underlying assumptions for assessing close encounters with manned aircraft do not adequately consider the different characteristics of smaller UAS-only encounters. The primary contribution of this paper is to explore quantitative criteria to use when simulating two or more smaller UASs in sufficiently close proximity that a midair collision might reasonably occur and without any mitigations to reduce the likelihood of a midair collision. The criteria assumes a historically motivated upper bound for the collision likelihood and subsequently identify the smallest possible NMAC analogs. We also demonstrate the NMAC analogs can be used to support modeling and simulation activities.

Aiming for the problems emerging in the PWM drive system with long cables, accurate modeling of power cables is the premise to predict and analyze the relevant phenomenon, and a proper filter design is the key solution to these problems. This paper proposes high-frequency cable models to represent the frequency-dependent characteristics, especially for the high-frequency resistance of the cable that is an easily overlooked factor but determines the damping of overvoltage. The proposed models can be used for accurately representing the cable parameters in a wide frequency range, and correctly simulating the differential mode (DM) overvoltage and common mode (CM) current, including the peak value, oscillation frequency and damping of the transient waveform. In addition, improved filter networks are proposed to suppress the DM voltage and CM current, with the merit of low losses, small volume and an excellent ability of suppressing overvoltage. The proposed cable models and the filter design have been validated in a 750W PWM drive system with 200m power cables.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.