Negative thermal quenching (NTQ) denotes that the integral emission spectral intensity of a given phosphor increases continuously with increasing temperature up to a certain elevated temperature. NTQ has been a subject of intensive investigation in recent years and a large number of phosphors were reportedly to have exhibited NTQ. In this paper, a collection of results in the archival literature about NTQ of specific phosphors are discussed from a macroscopic viewpoint in the following three aspects:1) Could NTQ of a given phosphor be reproducible?2) Could the associated data for a given phosphor exhibited NTQ be in line with the law of conservation of energy?3) Could NTQ of a given phosphor be demonstrated in a prototype WLED device? By analyzing typical cases based on common sense, it is hoped to increase the awareness for the issues with the papers reporting NTQ of the specific phosphors based on spectral intensity along with for the importance of keeping stability and consistency of the measurement conditions in temperature-dependent spectral intensity measurement which is a prerequisite for the validity of the measurement results.

Discussing quantum theory foundations, von Neumann noted that the measurement process should not be regarded in terms of a temporal evolution. A reason for his claim is insurmountability of the gap between reversible and irreversible processes. The time operator formalism that goes beyond such a gap is adequate framework for elaboration of the measurement problem. It considers signals to be stochastic processes, whether they correspond to variables or distribution densities. Signal processing like that utilizes statistical properties to perform its tasks, which is the definition of statistical signal processing. A hierarchy of the measurement process is indicated by crossing between states and devices, which implies an evolution in the temporal domain. The concept has generalized to an open system by the use of duality in frame theory.

This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained

The dairy industry relies heavily on milk pasteurization to ensure the safety and quality of milk products. Pasteurization is a process that involves heating milk to a specific temperature for a set period of time to kill harmful bacteria and other pathogens while preserving its nutritional value. recent years, newer techniques such as High Temperature Short Time (HTST) pasteurization have gained popularity due to their efficiency and effectiveness. HTST pasteurization involves rapidly heating milk to a high temperature for a short duration of time, followed by rapid cooling. This process helps to minimize the loss of flavor and nutrients in milk while ensuring its safety. However, there is still a need in the market for a compact and remotely controlled process plant for milk pasteurization. The proposed work aims to address this need by designing a process plant that is not only compact but also remotely controlled, allowing for efficient and convenient operation. can control the process plant remotely, allowing for flexibility and convenience in monitoring and managing the pasteurization process from anywhere with an internet connection

The study of velocimetry is important for characterizing and comprehending the effects of fluid flow, and the Particle Image Velocimetry (PIV) technique is one of the primary approaches for understanding the velocity vector field in a test section. Commercial PIV systems are expensive, with one of the main cost factors being high-speed camera equipment capable of capturing images at high frames per second (fps), rendering them impractical for many applications. This study proposes an evaluation of utilizing smartphones as image acquisition systems for PIV technique application. An experimental setup inspired by the known angular displacement of synthetic particles is proposed. A stepper motor rotates a plate containing an image of synthetic particles on its surface. The motion of the plate is captured by the smartphone camera, and the images are processed using PIVlab-MatLab® software. The use of two smartphones is assessed, with acquisition rates of either 240 fps or 960 fps and varying angular velocities. The results were satisfactory for velocities up to 0.7 m/s at an acquisition rate of 240 fps and up to 1.8 m/s at 960 fps, validating the use of smartphones as a cost-effective alternative for the PIV technique.

In recent years, the concept of Fiducial Reference Measurements (FRM) has been developed to highlight the need for precise and well-characterised measurements tailored explicitly to the post-launch calibration and validation (Cal/Val) of Earth observation satellite missions. The confidence that stems from robust unambiguous uncertainty assessment of space observations is fundamental to assessing the changes in the Earth system and climate model prediction, and delivering the essential evidence-based input for policy makers and society striving to mitigate and adapt to climate change. The underlying concept of an FRM has long been a core element of a Cal/Val program, providing a ‘trustable’ reference against which performance can be anchored or assessed. The ‘FRM’ label was created to embody into such a reference a set of key criteria. These criteria included the establishment of documented evidence of uncertainty with respect to a community-agreed reference (ideally SI-traceable) and specific tailoring to the needs of a satellite mission. It, therefore, facilitates comparison and interoperability between products and missions in a cost-efficient manner. CEOS Working Group Cal/Val (WGCV) is now putting in place a framework to assess the maturity and compliance of a ‘Cal/Val reference measurement’ in terms of a set of community-agreed criteria which define it to be of CEOS-FRM quality. The assessment process is based on a maturity matrix that provides a visual assessment of the state of any FRM against each of a set of given criteria; making visible where it is mature and where evolution and effort needs to be done. This paper provides the overarching definition of what constitutes an FRM and introduces the new CEOS FRM assessment framework.

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

When undertaking wind assessment around buildings using large eddy simulation (LES), the implementation of the integral length scale at the inlet for inflow generation is controversial, as real atmospheric length scales require huge computational domains. While length scales significantly influence inflow generation in the domain, their effect on the downstream flow field has not yet, been investigated. In this paper, we validate the effectiveness and accuracy of implementing a reduced turbulence integral length scale for inflow generation in LES results at the rooftop of low-rise buildings and develop a technique to estimate the real local length scales using simulation results. We measure the wind locally and calculate the turbulence length scales from the energy spectrum of the wind data and simulation data. According to these results, there is an excellent agreement between the length scale from simulation and measurement when they are scaled with their corresponding freestream/inlet value. These results indicate that a reduced integral length scale can be safely used for LES to provide a reliable prediction of the energy spectrum as well as the length scales around complex geometries. The simulation results were confidently employed to obtain the best location for a wind turbine installation on low-rise buildings.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

A variant of the von Neumann-Wigner Interpretation is proposed. Problems arising from the quantum Zeno effect are addressed as we have described previously. We do, however, offer some new, and perhaps unexpected observations. We are accustomed to thinking of wave function collapse as occurring consequent to laboratory measurements. We speculate that, whatever physical correlate of consciousness exists within the brain, it is quantum mechanical in the sense that a brain, left to itself, would eventually decohere into a state no longer compatible with its conscious functioning. Wave function collapse returns it to a state compatible with consciousness. Indeed, this may be its important reason for occurring. A universe without it simply could not play host to conscious brains. The fact that it also prevents us from encountering "absurd" situations in the laboratory is merely a fortunate dividend. Whenever a quantum measurement is made the universe's future history splits into a number of possibilities. This number may be very large or infinite. And we believe consciousness plays a vital role in this happening. A "conscious" universe where quantum measurements are being made allows for an enormous number of equally acceptable world-histories. An "unconscious" one, always evolving in a unitary fashion, allows for only one. If we assume that the decision as to which worldhistory is the real one (i.e. this one) is made at random we see that the universe is overwhelmingly more likely to be "conscious" than not.

The question whether a given set of test items can be considered “identical” is often addressed in terms of the homogeneity of the test material from which said items were taken. However, for some types of matrices – in particular, for matrices consisting of minute separate particles, only some of which carry the analyte under consideration – even in the case of homogenous test material, an irreducible source of variability between test items may remain: the fundamental variability. In this paper, the concept of fundamental variability is explained, and procedures for reducing and characterizing it are described.

Real-time closed-loop control of metallurgical processes is still in its infancy, mostly based on simple models and limited sensor data, challenged by extreme temperature, harsh process conditions. Contact-free thermal imaging-based measurement approaches thus appear to be particularly suitable for process monitoring. With the potential to generate vast amounts of accurate data in real-time, combined with artificial intelligence methods to enable real-time analysis and integration of expert knowledge, thermal spectral imaging is identified as a promising method offering more robust and accurate identification of key parameters, such as surface temperature, morphology, composition and flow rate.

Abstract: The calibrator is one of the most important factors in the calibration of various laser 3D scanning instruments. The requirements for diffuse reflection surface are specially emphasized in many national standards. In this study, the spherical calibrator and plane calibrator compara-tive measurement experiments were carried out. The black ceramic standard sphere, white ce-ramic standard sphere, metal standard sphere, metal standard plane and white ceramic standard plane were used to test the laser 3D scanner. In the spherical calibrators comparative measure-ment experiments, the results indicated that the RMS of the white ceramic spherical calibrator with reflectance about 60% is 10 times that of the metal spherical calibrator with the reflectance of about 15%, and the RMS of the black ceramic spherical calibrator with reflectance of about 11% is of the same order as the metal spherical calibrator. In the plane calibrators comparative measurement experiments, the RMS of flatness measurement is 0.077 mm for metal plane cali-brator with reflectance of 15%, and 2.915 mm for ceramic plane calibrator with reflectance of 60%. The results show that when the optimal measurement distance and incident angle are selected, the reflectance of the calibrator has a great effect on the measurement results, regardless of the outlines or profiles. Based on the experiments, it is recommended to use the spherical calibrator or the standard plane with reflectance of around 18% as the standard, which can obtain the rea-sonable results. In addition, it is necessary to clearly provide the material category and surface reflectance information of the standard when calibrating the scanner according to the measure-ment standard.

The aerosol optical depth is an important indicator of aerosol particle properties and associated radiative impacts. AOD determination is therefore very important to achieve relevant climate modeling. Most remote sensing techniques to retrieve aerosol optical depth are applicable to daytime given the high level of light available. The night represents half of the time but in such conditions only a few remote sensing techniques are available. Among these techniques, the most reliable are moon photometers and star photometers. In this paper, we attempt to fill gaps in the aerosol detection performed with the aforementioned techniques using night sky brightness measurements during moonless nights with the novel CoSQM: a portable, low cost and open-source multispectral photometer. In this paper, we present an innovative method for estimating the aerosol optical depth by using an empirical relationship between the zenith night sky brightness measured at night with the CoSQM and the aerosol optical depth retrieved at daytime from the AErosol Robotic NETwork. Such a method is especially suited to light-polluted regions with light pollution sources located within a few kilometers of the observation site. A coherent day-to-night aerosol optical depth and Ångström Exponent evolution in a set of 354 days and nights from August 2019 to February 2021 was verified at the location of Santa Cruz de Tenerife on the island of Tenerife, Spain. The preliminary uncertainty of this technique was evaluated using the variance under stable day-to-night conditions, set at 0.02 for aerosol optical depth and 0.75 for Ångström Exponent. These results indicate the set of CoSQM and the proposed methodology appear to be a promising tool to add new information on the aerosol optical properties at night, which could be of key importance to improve climate predictions.

The entropy of a system gives a powerful insight into its microscopic degrees of freedom, however standard experimental ways of measuring entropy through heat capacity are hard to apply to nanoscale systems, as they require the measurement of increasingly small amounts of heat. Two alternative entropy measurement methods have been recently proposed for nanodevices: through charge balance measurements and transport properties. We describe a self-consistent thermodynamic framework for treating few-electron nanodevices which incorporates both existing entropy measurement methods, whilst highlighting several ongoing misconceptions. We show that both methods can be described as special cases of a more general relation and prove its applicability in systems with complex microscopic dynamics – those with many excited states of various degeneracies.

This paper provides an open dataset of measured energy use, solar energy production, and building air leakage data from a 328 m² (3,531 ft²) all-electric, zero energy commercial building in Virginia, USA. Over two years of energy use data were collected at 1-hour intervals using circuit-level energy monitors. Over six years of solar energy production data were measured at 1-hour intervals by 56 microinverters. The building air leakage data was measured post-construction per ASTM-E779 Standard Test Method for Determining Air Leakage Rate by Fan Pressurization and the United States Army Corps (USACE) Building Enclosure Testing procedure; both pressurization and depressurization results are provided. The architectural and engineering (AE) documents are provided to aid researchers and practitioners in reliable modelling of building performance. The paper describes the data collection methods, cleaning, and convergence with weather data. This dataset can be employed to predict, benchmark, and calibrate operational outcomes in zero energy commercial buildings.

The purpose of this work is to determine the possibility of using an automated SkyWatcher Virtuoso system to analyze distribution of sky luminance. The article presents the procedure for measuring the sky luminance distribution defined according to CIE using a manual luminance meter cooperating with the SkyWatcher system. The use of matrix luminance meter was also analyzed.

Freezing of gait (FOG), a debilitating symptom of Parkinson’s disease (PD), can be safely studied using the stepping in place (SIP) task. However, clinical, visual identification of FOG during SIP is subjective and time consuming, and automatic FOG detection during SIP currently requires measuring center of pressure on dual force plates. This study examines whether FOG elicited during SIP in 10 individuals with PD could be reliably detected using kinematic data measured from wearable inertial measurement unit sensors (IMUs). A general, logistic regression model (AUC = 0.81) determined that three gait parameters together were overall the most robust predictors of FOG during SIP: arrhythmicity, swing time coefficient of variation, and swing angular range. Participant-specific models revealed varying sets of gait parameters that best predicted FOG for each participant, highlighting variable FOG behaviors, and demonstrated equal or better performance for 6 out of the 10 participants, suggesting the opportunity for model personalization. The results of this study demonstrated that gait parameters measured from wearable IMUs reliably detected FOG during SIP, and the general and participant-specific gait parameters allude to variable FOG behaviors that could inform more personalized approaches for treatment of FOG and gait impairment in PD.

In this article authors shows chosen problems of technical state diagnosis with the use of identification and technical diagnostics methods such as experimental modal analysis. Relations between methods of dynamic state evaluation and methods of technical state evaluation were indicated. Example modal analysis results illustrate the complexity of projecting dynamic state researches into diagnostic researches of state evaluation.

Ammonia (NH3), the most prevalent alkaline gas in the atmosphere, plays a significant role in PM2.5 formation, atmospheric chemistry, and new particle formation. This paper reviews quantification of [NH3] through measurements, satellite-remote-sensing, and modeling reported in over 500 publications towards synthesizing current knowledge of [NH3], focusing on spatiotemporal variations, controlling processes, and quantification issues. Most measurements are through regional passive sampler networks. [NH3] hotspots are typically over agricultural regions like the Midwest US and North China Plain, with elevated concentrations reaching monthly averages of 20 and 74 ppbv, respectively. Topographical effects dramatically increase [NH3] over the Indo-Gangetic Plains, North India and San Joaquin Valley, US. Measurements are sparse over oceans, where [NH3] ≈ few tens of ppbv, variations of which can affect aerosol formation. Satellite-remote-sensing (AIRS, CrIS, IASI, TANSO-FTS, TES) provides global [NH3] quantification in the column and at surface since 2002. Modeling is crucial for improving understanding of NH3 chemistry and transport, its spatiotemporal variations, source apportionment, exploring physicochemical mechanisms, and predicting future scenarios. GEOS-Chem (global) and FRAME (UK) models are commonly applied for this. A synergistic approach of measurements↔satellite-inference↔modeling is needed towards improved understanding of atmospheric ammonia, of concern from the standpoint of human health and the ecosystem.

Understanding the shoulder-specific load in handball is important for both prevention and rehabilitation of shoulder injuries. The shoulder-specific load is largely a result of the number and speed of throws. However, it is difficult to quantify number and speed of throws in handball due to limitations in the current technology. Therefore, the purpose of this study was to develop a novel method to estimate throwing speed in handball using a low-cost accelerometer-based device. Nineteen experienced handball players each performed 25 throws of varying types while we measured the acceleration of the wrist using the accelerometer and the throwing speed using 3D motion capture. Using cross-validation, we developed four prediction models using combinations of the logarithm of the peak total acceleration, sex and throwing type as the predictor and the throwing speed as the outcome. We found that all models were well-calibrated (mean calibration of all models: 0.0 m/s, calibration slope range: 0.99-1.00) and precise (R2 = 0.71-0.85, mean absolute error = 1.32-1.82 m/s). We conclude that the developed method appear to provide practitioners and researchers with a feasible and cheap method to estimate throwing speeds in handball.

Sentinel-1 satellite system continuously observes European countries in a relatively high revisit frequency of 6 days per orbital track. Given the Sentinel-1 configuration, most areas in Czechia are observed every 1–2 days by different tracks in a moderate resolution. This is attractive for various types of analyses by various research groups. The starting point for processing is an original data provided by ESA, for interferometry (InSAR) this level is a Single Look Complex (SLC) data. This work represents advantages of storing data augmented to a specifically corrected level of data, SLC-C. The presented database contains Czech nation-wide Sentinel-1 data stored in burst units that have been preprocessed to the state of a consistent well-coregistered dataset of SLC-C. These are resampled SLC data with their phase values reduced by a topographic phase signature, ready for fast interferometric analyses (an interferogram is generated by a complex conjugate between two stored SLC-C files). The data can be used directly into multitemporal interferometry techniques, e.g. Persistent Scatterers (PS) or Small Baseline (SB) techniques applied here. A further development of the nation-wide system utilising SLC-C data would lead into a dynamic state where every new pre-processed burst triggers a processing update to detect unexpected changes from InSAR time series and therefore provide a signal for early warning against a potential dangerous displacement, e.g. a landslide, instability of an engineering structure or a formation of a sinkhole. An update of the processing chain would also allow use of cross-polarised Sentinel-1 data, needed for polarimetric analyses. The current system is running at a national supercomputing centre IT4Innovations in interconnection to the Czech Copernicus Collaborative Ground Segment (CESNET), providing fast on-demand InSAR results over Czech territories. A full nation-wide PS processing using data over Czechia has been performed in 2017, discovering several areas of land deformation. Its downsampled version and basic findings are demonstrated within the article.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

Background: Transit-time flow measurement (TTFM) is frequently used to evaluate intraoperative quality control during coronary artery bypass grafting (CABG). Although TTFM has the ability to assess graft failure intraoperatively, the perioperative factors affecting TTFM during CABG surgery remain poorly understood. Methods: Patients who underwent CABG surgery at a single institution between July 2016 and May 2018 were prospectively evaluated. Patients’ demographic characteristics, previous medical history, Euroscore, the results of preoperative blood tests, and intraoperative data were recorded. TTFM and blood viscosity were measured hemodynamically, and mean flow (mL/min) and pulsatility index (PI) were recorded. Arterial blood gas was analyzed immediately after anastomosis of the left internal mammary artery (LIMA) to the left descending artery (LAD) and before sternal closure. Factors associated with TTFM were assessed by multiple linear regression analysis. Results: Of the 62 patients who underwent CABG surgery during the study period, 57 were evaluated, including 49 who underwent off-pump and eight who underwent on-pump surgery. Blood viscosity was not significantly associated with TTFM (p > 0.05). However, TTFM was significantly associated with body mass index (BMI), systolic blood pressure, and cardiac index (p < 0.05 each). Conclusions: Blood viscosity was not significantly associated with intraoperative graft flow. Blood flow of graft vessels, however, was significantly associated with BMI, systolic blood pressure, and cardiac index.

Additive manufacturing (AM) is a promising new technology that is having a very fast growth from home workshops to high-tech cutting-edge factories. As any manufacturing technique, adequate metrology services are needed to assure the quality of items manufactured by AM. One of the most widely used instruments to measure the characteristics of surfaces manufactured with AM is the confocal microscope. In this paper, authors present a whole calibration procedure for confocal microscopes designed to be implemented preferably in workshops or industrial environments rather than in research and development departments. Because of that, it is as simple as possible. The procedure is designed without forgetting any of the key aspects that need to be taken into account and based on classical reference material standards. These standards can be easily found in industrial dimensional laboratories and easily calibrated in accredited calibration laboratories.

Injuries to the ligaments of the knee are extremely common among athletes who participate in high-risk sports, or any sport that requires frequent cutting motions, jumping, or contact. In order to determine the best way to heal these injuries, it is important to understand not just the pathology of the injury, but also the biomechanical factors that are affected, including stability and steadiness. While many studies have been done to examine the stability of healthy knees, there is little to no existing literature on stability of knees afflicted by injury. In order to surpass this obstacle, static steadiness and dynamic stability data was collected using the Lockhart Monitor phone application and Xsens accelerometers, respectively, both before and after completion of a course of physical therapy in a patient with a grade 2 medial collateral ligament (MCL) tear. These results were then used to determine the degree to which the prescribed physical therapy protocol was effective in healing the MCL, which can be useful for tweaking the individual protocol for future conservative treatment and management of the injury.

Tuning nonlinearity of the laser is the main source which will deteriorate the spatial resolution in optical frequency domain reflectometry system. We develop methods for tuning nonlinearity correction in the OFDR system from the aspects of data acquisition and also the posting-processing. A zero-crossing detection scheme is researched and implemented by a customized circuit. Equal-spacing frequency sampling is therefore achieved in real-time. The maximum sensing distance can reach to the same length of the auxiliary interferometer. The zero-crossing detection for the beating frequency of 20MHz is achieved. Then, a nonlinearity correction method based on the self-reference method is proposed. The auxiliary interferometer is no longer necessary in this scheme. The tuning information of the laser is extracted by a strong reflectivity point at the end of the sensing arm in the main interferometer. The tuning information can then be used to resample the raw signal and the nonlinearity correction can be achieved. The spatial resolution test and the distributed sensing experiments are both performed based on this nonlinearity correction method. The results validated the feasibility of the proposed method. The method reduces the hardware and data burden for the system and has a potential value on the system integration and miniaturization.

In a depolarizing instrument, such as a broadband imaging spectrometer, the depolarizers are placed on the system for stabilization the optical signal. They are also used to reduce measurements offsets due to strong polarization dependence, which produce drastic deterioration of the signal to noise ratio. Dynamic depolarizer with a controllable degree of polarization is also required to study the effect of noise on quantum information. The article described a new instrument for characterization the variable depolarizer with features which make it different from a polarimetric system. The analysing system based on the simple structural design and has good stability for real-time measurement. A practical application of the described interferometer system for variable depolarizer characterization is also presented.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

A large number of physicists now admit that quantum mechanics is a non-local theory. EPR argument and the many experiences (including recent “loop-hole free” tests) showing the violation of Bell’s inequalities seem to have confirmed convincingly that quantum mechanics cannot be local. Nevertheless, this conclusion can only be drawn inside a standard realist framework assuming an ontic interpretation of the wave function and viewing the collapse of the wave function as a real change of the physical state of the system. We show that this standpoint is not mandatory and that if the collapse is no more considered as an actual physical change, it is possible to recover locality.

Live fuel moisture content (LFMC) influences fire activity at landscape scale and fire behavior in laboratory experiments. However, field evidences linking LFMC to fire behavior are very limited despite numerous field experiments. In the present study, we reanalyze a shrubland fire dataset with a special focus on LFMC to explain this counterintuitive outcome. We found that this controversy might result from three reasons. First, the range of experimental LFMC data was too moist to reveal significant effect with the widespread exponential or power functions. Indeed, LFMC exhibited a strong effect below 100%, but marginal above this threshold, contrary to these functions. Second, we found that the LFMC significance was unlikely when the size of the dataset was smaller than 40. Finally, a complementary analysis suggested that 10 to 15% of random measurement error in variables could lead to an underestimation by 30 % of the LFMC effect. The effect of LFMC in field experiments is thus stronger than previously reported in the range prevailing during the actual French fire season and in accordance with observations at different scales. This highlights the need to improve our understanding of the relationship between LFMC and fire behavior to refine fire danger predictions.

A heat transfer model, has determined millimeter crude oil thicknesses on saltwater at night. Model inputs are calibrated thermographic imagery, weather station data, metrological observations, and crude oil thermal conductivity. Outdoor field-testing was performed at the National Oil Spill Response & Renewable Energy Test Facility (Ohmsett) to determine model accuracy. Alaskan North Slope (ANS), Hoover Offshore Oil Pipeline System Blend (HOOPS), and ROCK crude oils were placed at varying mm depths. A roof-top mounted thermal camera measured the average oil surface temperature for each target and converted to oil spill thickness. The fidelity of the thickness measurements is dependent on the accurate measurement of the atmospheric and weather parameters, sea state, heat transfer constants, crude oil evaporation rates, and calibration and stability of the thermal camera.

This study was undertaken to investigate and analyze noise pollution in a large Chinese governmental hospital’s medical intensive care unit and compare to the WHO guidelines.This cross-sectional study was conducted in a MICU at a public governmental teaching hospital in Fujian province between July and August of 2017. A WENSN® WS1361 Integrated Sound Level Meter (China) was used for continuous every five seconds one week noise levels recording. After this measurement, the decibel meter was used for recording different location of isolation rooms and open bays, including occupied and unoccupied patient, and recording sound events occurs in the ICU to identify sources of noise. Peak and average noise levels were obtained from the meter, and data were downloaded from the WS1361 into a laptop computer. The measured mean equivalent sound pressure levels (L) and standard Aeq deviation over one week period were 66.64±7.57 dB(A), with acute spikes reaching 119.7 dB(A), the average sound level for a 24 hour period in a work day was 68.03±5.07 dB(A). These are higher than the current daytime environmental noise limit of 40-45 decibels in China and WHO. Mean work day noise was significantly louder than weekend time, there was a significant difference in work days and weekend (t=16.85;P=0.000).There was a statistical difference between the day time and night time shifts (t=34.67;P=0.000). The isolation rooms were significantly quieter than the open-bay rooms(t=46.15; p=0.00), sound levels in the occupied and unoccupied rooms also had significant difference(t=17.26; P=0.000).Two types of noise resources, including twenty kinds sources were identified and measured, mean noise levels ranged from of 61.33 to 79.21 dB(A). This study shows noise levels in intensive care units were exceeded the recommended. The study of the influence of noise on patient and staff is needed, and noise reduction strategies must be conduct in ICU.

Measuring farms sustainable innovativeness is a big challenge for both practitioners and academics. The need of sustainable innovativeness assessment in the agricultural business is reasoned in the article. Unfortunately, the features of the farms sustainable innovativeness measurement have not yet been investigated, and any objective methodology for innovativeness assessment is not presented as well. The objective of this article is to find possibility of use some methodology for measuring farm sustainable innovativeness, which would allow ranking farms by this aspect. The article demonstrates the need for multi-criteria method of innovativeness measurement and substantiates the complex proportional assessment method (Copras) as the most appropriate for solution of indicated problem. The model for use of offered method is presented and the practical application of the model is submitted. The final result refuted the opinion that farm innovation depends only on the possibilities to invest funds in a certain area. Indeed, staff creativity and the position of the management regarding certain areas of business make an essential contribution to the sustainable innovativeness level in the agricultural organizations.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

In order to enhance the accuracy of the relative velocity measurement for the Mars explorer formation flight, we develop a relative velocity measurement method. In this method, the spectrometers at two Mars explorers are adopted to measure the starlight frequency shift and to estimate the velocity with respect to the star. Unfortunately, the instantaneous velocity of star can not be predicted accurately, which results in a large error in the velocity measurement. The difference of these two velocities, which does not include the proper motion of star, is the relative velocity between a pair of Mars explorers at the direction of the star. However, this navigation method can not work alone because of unobservability. To make the navigation system observable and improve the accuracy of both absolute and relative navigation for the Mars explorer formation flight, we combine it with X-ray pulsar navigation and the inter-satellite links, and propose an autonomous integrated navigation method with observability. In this integrated navigation scheme, the extended Kalman filter is adopted to deal with the relative velocity, the inter-satellite links and the pulse time-of-arrival, and estimate the absolute and relative navigation information for the Mars explorer formation flight. The simulation results demonstrate that both absolute and relative navigation accuracy of the proposed method are higher than that of the pulsar navigation, especially the relative one.

Unmanned Aerial Vehicles (UAVs) are now filling in the gaps between spaceborne and ground-based observations and enhancing the spatial resolution and temporal coverage of data acquisition. In the realm of hydrological observations, UAVs have a key role to quantitatively characterize the surface flow allowing for remotely accessing the water body of interest. In this paper we propose a technology which uses a sensing platform encompassing a drone and a camera to determine the water level. The images acquired my means of the sensing platform are then analyzed using the Canny method to detect the edges of water level and of Ground Control Points (GCPs) used as reference points. The water level is then retrieved from images and compared to a benchmark value obtained by a traditional device. The method is tested at four locations in an artificial lake in central Italy. Results are encouraging as the overall mean error between estimated and true water level values is around 0.02 m. This technology is well suited to improve hydraulic modeling and thus provide a reliable support to flood mitigation strategies also in uneasy-to-access environments.

Dynamic measurement error correction is an effective method to improve the sensor precision. Dynamic measurement error prediction is an important part of error correction, support vector machine (SVM) is often used to predicting the dynamic measurement error of sensors. Traditionally, the parameters of SVM were always set by manual, which can not ensure the model’s performance. In this paper, a method of SVM based on an improved particle swarm optimization (NAPSO) is proposed to predict the dynamic measurement error of sensors. Natural selection and Simulated annealing are added in PSO to raise the ability to avoid local optimum. To verify the performance of NAPSO-SVM, three types of algorithms are selected to optimize the SVM’s parameters, they are the particle swarm optimization algorithm (PSO), the improved PSO optimization algorithm (NAPSO), and the glowworm swarm optimization (GSO). The dynamic measurement error data of two sensors are applied as the test data. The root mean squared error and mean absoluter percentage error are employed to evaluate the prediction models’ performances. The experiment results show that the NAPSO-SVM has a better prediction precision and a less prediction errors among the three algorithms, and it is an effective method in predicting dynamic measurement errors of sensors.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

This article is about a framework for determining the degree of realism of any given 1 passenger ride motion discomfort measurement formula. After providing some context and reviewing 2 evidence of deficiency in currently popular ride motion discomfort measurement formulas, the article 3 outlines the research program that needs to be carried out in order to establish such a framework. 4 The research begins with gathering recordings of uncomfortable ride motion episodes encountered in 5 a chosen type of passenger transport service. It then has test subjects compare the episodes via a ride 6 motion simulator and adjust their amplitudes pair wise until they cause equal discomfort. It explains 7 how to take the pair wise amplitude adjustments and determine amplitude adjustments that bring all 8 of the motion episode recordings to a common level of discomfort so that they form a normalized set. 9 Then, the lower the scatter of the scores assigned by any given discomfort measurement formula to 10 the members of that set, the more realistic that formula will be for the chosen service.

The purpose of this study was to investigate the relationship between clinical outcomes and lateral thrust before and after unicompartmental knee arthroplasty (UKA) using inertial measurement sensor units. Eleven knees were evaluated with gait analysis. The varus angular velocity was used to evaluate lateral thrust. The femoro-tibial angle (FTA) and hip-knee-ankle angle (HKA) were used to evaluate lower limb alignment, and Oxford Knee Score (OKS) and Japanese Orthopaedic Association Score (JOA) were used to evaluate clinical outcomes. The mean pre-UKA peak varus velocity was 37.1 ± 9.8°/sec, and that of post-UKA was 28.8 ± 9.1°/sec (p=0.00003). Assuming the definition of lateral thrust is when varus angular velocity is more than 28.1°/sec, 81.8% of patients had lateral thrust preoperatively, but this decreased to 55.6% postoperatively. Both OKS and JOA improved after surgery. In addition, HKA was -7.9° preoperatively and -5.8° postoperatively (p=0.024), and FTA was 181.4° preoperatively and 178.4° postoperatively (p=0.012). There was a positive correlation between postoperative JOA and FTA, indicating that changes in postoperative alignment affected clinical outcomes. This study quantitatively evaluated the disappearance of lateral thrust by UKA, and it found that the stability can be achieved by UKA for unstable knees with lateral thrust.

In horses, quantitative assessment of gait parameters, as the use of inertial measurement units system (IMUs), might help in the decision-making process. However, it requires financial investment, is time-consuming, and lacks accuracy if displaced. An innovative Artificial Intelligence marker-less Motion Tracking System (AI-MTS) may overcome these limitations in the field. Our aim was to compare the level of agreement and accuracy between both systems and visual clinical assessment. Twenty horses underwent locomotion analysis by visual assessment, IMUs and AI- MTS systems, in the following conditions: straight hard (SH), straight soft (SS), left and right circle hard (LCH, RCH) and soft (LCS, RCS). A greater number of horses were considered sound by clinical examination, compared to those identified as symmetric by the two gait analysis systems. More limbs were considered asymmetric by the AI-MTS compared to IMUs, suggesting its greater sensitivity. The greatest agreement between the two systems was found for the difference between two minima in vertical head position in SH, while the lowest for the difference between two minima in vertical pelvis position in SS, reflecting the difficulties in assessing asymmetry of hindlimbs. Some degree of asymmetry may be clinically relevant, suggesting its regular use in training horses.

China is a traditional agricultural country, and the integration of rural industries has become an essential policy direction for the current strategy of agricultural modernization in China. In recent years, the agricultural industrial chains across various regions of China have consistently expanded and extended. The multifunctionality of agriculture is continuously unearthed, and the principal entities managing agriculture have become increasingly diversified and have grown significantly. New industries and forms in agriculture emerge incessantly. Accurately and profoundly understanding the inherent features of the integration of industries in rural China, establishing a scientific and rational measurement index system in line with the current status and development goals of rural China, and employing appropriate measurement methods to assess its development level and process, is instrumental in comprehending the level of integrated development in various regions. This aids in identifying challenges in the developmental process and proposing targeted developmental strategies. Hence, this paper, rooted in the integration of rural industries, cross-industry, industry extension, industry agglomeration, and industry penetration, sets up an measurement index system. Using provincial panel data from 2011 to 2020, the paper measures the level of integrated development in rural industries across China and its 31 provinces. Based on the measurement results, further techniques such as kernel density estimation and Gini coefficient decomposition have been used to analyze the spatial distribution characteristics and dynamic trends of the integrated development of rural industries in China. Research indicates that during the sample period, the overall level of integrated development in rural industries in various provinces in China has shown an upward trend. Development among the eastern, central, and western regions is highly uneven, but this disparity has been gradually narrowing in recent years. Furthermore, the levels of integrated development in different provinces exhibit significant spatial agglomeration effects. The development level of neighboring regions significantly impacts the province's development status. In the process of integrated development of rural industries in China, there's a trend where "it's easier to downgrade than to upgrade," with very few regions achieving leapfrog development.

Climate change and net zero are expected to have a significant impact on eco-nomic activity in developing countries, and thus, on the financial cash flow of organizations. In this paper, we propose a procedure for assessing the financial impact of climate change on organizational cash flow in developing countries. Our study contributes to the research on scenario-based climate change impact analysis. The applied research design is exploratory and mainly qualitative, constructing financial impact scenarios combined with narratives to determine the impact of climate change on individual cash flow line items. The narra-tives rationalize cash flow variations and enrich the estimates by adding expert knowledge, in the form of financial micro-stories and descriptions to the pro-posed procedure. We present a hypothetical citrus farming company in a de-veloping country to demonstrate the application of the proposed measurement procedure. The results obtained suggest that (1) the procedure is practical be-cause financial cash flows are known and widely used in financial analysis and because they can be implemented in a spreadsheet; that (2) the procedure pro-vides flexibility because it can be adapted to suit the specific needs of different companies, depending on a selected climate change scenario, the company’s exposure to climate change, its resilience and vulnerability; (3) that the prac-tice of thinking in terms of financial worst-case, base-case and best-case sce-narios, which reflect different levels of uncertainty, helps to model the finan-cial impacts of climate change and provides a forward-looking perspective on how much a company’s cash flow could change.

The bionic polarization imaging navigation sensor (BPINS) is a navigation sensor that provides absolute heading, and it is of practical engineering significance to model the measurement error of BPINS. The existing BPINSs are still modeled using photodiode-based measurements rather than imaging measurements and are not modeled systematically enough. This paper proposes a measurement model of BPINS that takes into account the geometric and polarization errors of the optical system. Firstly, the key error factors affecting the measurement accuracy of BPINS are systematically investigated and the Stokes vector-based measurement error model of BPINS is established. Secondly, based on its measurement error model, the effect of the error source on the measurement performance of BPINS is quantitatively analyzed by using Rayleigh scattering to generate scattered sunlight as a known incident light source. The experimental results show that the coordinate deviation of the principal point has a greater impact, followed by grayscale response inconsistency of CMOS and integration angle error of micro-polarization array, and finally lens attenuation. This finding can guide the subsequent calibration of BPINS, and the quantitative results provide an important reference for its optimal design.

The scope of this study was twofold: first, to introduce a new method in examining measurement invariance, especially with large-scale studies where a large number of group comparisons are involved: the alignment approach, where only configural invariance is necessary to achieve measurement invariance. Second, to evaluate the psychometric robustness of this approach using real-life data. Particularly, we applied this approach to examine whether the factor structure of a cognitive ability test (PGAT) exhibits measurement invariance across the 26 universities of the Kingdom of Saudi Arabia. The sample consisted of 9,849 graduate students from 26 universities around the Kingdom. The results indicated a robust configural model suggesting that the P-GAT subscales were invariant across the 26 universities. Finally, the aligned factor mean values were estimated, and factor mean comparisons of every group’s mean with all other group means were conducted for both cognitive domains (Verbal and Quantitative). In both domains, King Saud University had the highest mean score among all universities. Moreover, its mean factor score was significantly higher than any other university besides Dammam University. On the other hand, several universities allocated at the northern and Southern borders of the country exhibited the lowest factor mean scores.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Developing a low-cost wireless energy meter with power quality measurement for smart grid applications represents a significant advancement in efficient and accurate electrical energy monitoring.In increasingly complex and interconnected electrical systems, this device is essential in various applications, such as smart grids, enabling real-time energy usage monitoring. In such a context, smart meters expand the possibilities for sustainable and efficient energy use and promote better utilization of energy sources, especially non-renewable ones. According to the 2020 International Energy Agency (IEA) research, non-renewable energy sources represent 65% of the global total. The smart meter developed in this work is built based on the ESP32 microcontroller and easily accessible components, using a user-friendly development platform that offers a cost-effective solution while ensuring reliable performance. The main objective of the smart meter development was to enhance the software and simplify the hardware. Unlike traditional meters that perform electrical parameter calculations using complex hardware circuits, this project performed the calculations directly on the microcontroller. This approach reduced the complexity of the hardware, simplifying the meter’s design. With the high-performance processing capability of the microcontroller, efficient and accurate calculations of electrical parameters were achieved without the need for additional circuits. This software-driven approach with simplified hardware brought benefits such as reduced production costs, lower energy consumption, and increased meter development and updates flexibility. Furthermore, the integrated wireless connectivity in the microcontroller enables the transmission of collected data to remote monitoring systems for later analysis. The developed smart meter offers cost, energy efficiency, and flexibility benefits. It represents an innovative, efficient, and versatile solution for smart grid applications.

To improve the measurement accuracy of wood density and study the linear correlation between the drill feed resistance and wood density, a new micro drill instrument that can can simultaneously measure the rotation resistance and feed resistance of the drill needle was designed. The test wood samples included hardwood, softwood and conifer. The absolute dry density of each wood sample was measured. The drill resistance data was tested by using self-developed micro drill instrument and Resistogaph 650-SC. 4 linear models between drill resistance and the absolute dry density of wood . The results showed that: the statistical indicators of each model of the self-made micro drill resistance in-strument were better than the corresponding indicators of Resistogaph 650-SC; the coefficient of determination of the linear regression model between the feed resistance of the self-made micro drill resistance instrument and the absolute dry density of wood was 0.946; the statistical indicators of model including rotation resistance and feed resistance, were better than those of the model only including rotation resistance. Therefor, the design proposed in the article is reasonable, and increasing the feed resistance can improve the measurement accuracy of the micro drill resistance instrument for measuring wood density.

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

In order to realize the accurate measurement of wearable sphygmomanometer, this paper selects the micro electro mechanical system (MEMS) pressure sensor with small size, low cost and high accuracy, and proposes a flexible packaging method combining Parylene and Polydimethylsiloxane (PDMS). The flexible packaging sensor protects the sensor chip while ensuring the comfort of the measured person. It can be worn for a long time, and the encapsulated sensor has good accuracy and sensitivity. At the same time, the encapsulated MEMS pressure sensor was used to collect good pulse signals and extract multiple pulse wave characteristic parameters. A blood pressure measurement method based on the combination of arterial tonometry method and pulse wave parameters method was proposed, and multiple machine learning algorithms were compared and analyzed to select the algorithm model with the smallest error as the optimal regressor. The experimental results show that the blood pressure measurement method combining the arterial tonometry method and the pulse wave parameters method can effectively improve the accuracy of blood pressure measurement. The experimental results demonstrate that the combination of arterial tonometry and pulse wave parameter methods can effectively enhance the accuracy of blood pressure measurement, with the random forest model serving as the optimal regressor. The average deviation between the systolic blood pressure measured by our self-made sphygmomanometer and the commercial sphygmomanometer was 0.86mmHg, with a standard deviation of 4.04mmHg. The average deviation of diastolic blood pressure was 0.63mmHg, with a standard deviation of 5.15mmHg, meeting the AAMI standard for clinical practice.

Hillslope and mountain roads are often the source of erosion, which in turn can lead to larger landslides and other types of mass-movements. For this reason, low-cost repeat surveys that can be done by practitioners and not solely scientists and engineers is essential. To solve this issue the present contribution shows the testing and applicability of a mix of SfM-MVS and low-cost SLAM technology to provide erosion information. The low-cost SLAM generated between 300 ~ 900 points per square meter, while SfM-MVS created between ~11,000 to 900,000 points. The density is however a trade-off against a spatially varying error, although the variability at the road-cut scale only ranges from 2 cm vertically to 2.5 cm in x,y,z based on the C2C algorithm. Furthermore, this error tends to be more important in the higher section of the cutout (further away from the sensor and at a flatter angle). It is thus possible to measure small-scale roadside change, providing that the change is in the range of >5 cm (adding the maximum potential error twice) and providing that the road-cut is such that the sensors can be brought close to the surface (camera or sensor on a pole). The authors suggest that it can be a solution for state and agencies with limited funding and that cannot afford regular laser or for roadside that are difficult to access.

Digital wellbeing concerns the balance and health we may experience in digital use, and the existing studies have focused on adolescents and adults. However, young children are more vulnerable to digital overuse and addiction than adults; thus, their digital wellbeing deserves empirical exploration. This scoping review synthesized and evaluated 35 collected studies on young children’s digital use and their wellbeing that were published until October of 2022 to understand the definitions, measurements, contributors, and interventions. The synthesis of evidence revealed that: (1) there was no consensus about its definition; (2) there were no effective measurements of young children’s digital wellbeing; (3) both child factors (duration and place of digital use, child demographic characteristics) and parent factors (digital use, parental perception, and mediation) contribute to young children’s wellbeing; and (4) there were some effective applications and interventions. This review contributes to the theoretical development by mapping the existing work on young children's digital wellbeing, proposing a model, and identifying the research gaps for future studies.

Intensive care nurses are highly prone to occupational stress and burnout, affecting their physical and mental health. The occurrence of the pandemic and related events increased nurses’ workload and exacerbated stress and burnout. We conducted a prospective longitudinal mixed-methods study with a cohort of nurses working in a medical ICU (COVID unit; n = 14) and cardiovascular ICU (non-COVID unit; n = 5). Each participant was followed for six 12-hour shifts. Validated questionnaires measured occupational stress and burnout prevalence. Wrist-worn wearable technologies recorded physiological indices of stress. Participants elaborated on the contributors to stress via post-study questionnaire. Data were analyzed using statistical and qualitative methods. Participants who cared for COVID patients at the COVID unit were 3.71 times more likely to experience stress (p &lt; .001) in comparison to non-COVID unit participants. No differences in stress levels were found when the same participants worked with COVID and non-COVID patients at different shifts at the COVID unit. The cohorts expressed similar contributors to stress including communication tasks, patient acuity, clinical procedures, admission processes, proning, labs, and assisting coworkers. Nurses in COVID units, irrespective of whether they care for a COVID patient, may experience high occupational stress and burnout.

Fringe projection profilometry(FPP) has been extensively applied in various fields for its superior fast speed, high accuracy and high data density. However, measuring some objects with high reflective surfaces or high dynamic range surfaces remains challenging for FPP. Some multiple exposure image fusion methods have been proposed and successfully improved the measurement performance for these kinds of objects. Normally, these methods have a relatively fixed sequence of exposure settings determined by artificial experience or trial and error experiments, which may decrease the efficiency of the entire measurement process and may have less robustness to various environmental lighting conditions and object reflective properties. In this paper, a novel self-adaptive multiple exposure image fusion method is proposed with two main aspects of improvement on adaptively optimizing the initial exposure and the exposure sequence. By introducing the theory of information entropy, combined with the analysis of the characterization of fringe image entropy, an adaptive initial exposure searching method is first proposed. Then, an exposure sequence generation method based on dichotomy is further described. On the base of these two improvements, a novel self-adaptive multiple exposure image fusion method for FPP as well as its detailed procedures are given. Experimental results validate the performance of the proposed self-adaptivity multiple exposure image fusion method by measuring the objects with different surface reflectivity and in different ambient lighting conditions.

Observation of parity-violating effects in chiral molecules is a long-standing challenge of the molecular spectroscopy community. In the microwave regime, the difference in transition frequencies between enantiomers is predicted to be below the mHz level, which is considerably beyond current experimental capabilities. The most promising future efforts combine vibrational spectroscopy, buffer gas cooling, and carefully chosen molecular candidates with large predicted parity-violating shifts. Here, we demonstrate for the first time high-precision differential microwave spectroscopy, achieving sub-Hz precision by coupling a cryogenic buffer gas cell with a tunable microwave Fabry-Perot cavity. We report statistically limited sub-Hz precision of (0.08±0.72) Hz, observed between enantiopure samples of (R)-1,2-propanediol and (S)-1,2-propanediol at frequencies near 15 GHz. We confirm highly repeatable spectroscopic measurements compared to traditional pulsed-jet methods, opening up new capabilities in probing subtle molecular structural effects at the 10−10 level and providing a platform for exploring sources of systematic error in parity-violation searches. We discuss dominant systematic effects at this level and propose possible extensions of the technique for higher precision.

The present study was conducted the status of sea bass from Kokko and Kyuntone of The Gulf of Motttama Wetland (GoMW) area in Thanatpin Township in Bago Region Myanmar from September 2019 to August 2020. Fifty specimens were monthly collected, measured and weighed. Invoices of sea bass were collected for the depot and fish sellers by monthly. In Kokko, mean value of standard length and body weight were highest in March (32.70±1.58, 660.7±112.23). The mean value of standard length was peak in January (31.39±7.16) but peak of body weight was in March (963.24±280.86) in Kyuntone villages. The lowest mean value of standard length and body weight were found in June at both study areas. According to the invoice data revealed that monthly catch weight of sea bass is most abundance in October (829.92) kg in Kokko, (339.12) kg in Kyuntone. Based on price of relations to size group, small size C &lt; 300g (41%) was mostly abundance in Kokko and in Kyuntone small size C &lt; 300g (35%) was second abundance. Specimens were not landed in April and May. In June, young specimens were very rarely seen in both study sites. The important roles of wetland fishes, the economic valuation of GOMW in Myanmar and samples of fishing gear and value chain of sea bass in Myanmar was expressed in this study.

Background: Recently some photon models of a Wigner's friend experiment have led investigators to suggest objective reality does not exist, and to publish non-academic articles with such claims. The public is not equipped to evaluate the severe limitations of these experiments. The separation of Wigner from the experiment and use of only reversible coherent processes for the friend allow operations that are not possible in ordinary reality according to the latest quantum research. Methods: We suggest directly testing the implied claim that objective reality, including incoherent objects with irreversible non-destructive memory, can be held in superposition. We suspect it will fail, but provide for a graduated approach that may discover something about the conditions for superposition collapse. To this end we design a thought experiment to model the objective world, investigating under what conditions experimenters in the same world (ensemble member) will be able to record a result and find it does not appear to change. An observer has a viewing apparatus and a memory apparatus. A second uncorrelated viewer of the same recorded result is employed to obtain objectivity. By hypothesis the uncorrelated second viewer obtains the same view of the measurement record as the first observer. There are not two measurements. This is not an investigation of hidden variables. Results: To model the objective world, incoherent and irreversible processes must be included. To test for superposition, coherence has to be established. These seem to present a contradiction. Conclusions: The thought experiment has suggested new places to look other than size for the origin of objective reality from the quantum world, casts doubt on the Many-Worlds interpretation, and provides a method of testing it.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

Rapid and accurate prediction of residual stress in metal additive manufacturing processes is of great importance to guarantee the quality of the fabricated part to be used in a mission-critical application in the aerospace and automotive industries. Experimentation and numerical modeling are valuable tools for measuring and predicting the residual stress; however, to-date conducting experimentation and numerical modeling is expensive and time-consuming. Thus, herein, a physics-based thermomechanical analytical model is proposed to predict the residual stress of the additively manufactured part rapidly and accurately. A moving point heat source approach is used to predict the temperature field by considering the effects of scan strategies, heat loss, and energy needed for solid-state phase transformation. Due to the high temperature gradient in this process, part experiences a high amount of thermal stress following solidification which may exceed the yield strength of the material. The thermal stress is obtained using Green’s function of stresses due to the point body load. The Johnson-Cook flow stress model is used to predict the yield surface of the part under repeated heating and cooling. As a result of the cyclic heating and cooling and the fact that the material is yielded, the residual stress build-up is predicted based on incremental plasticity and kinematic hardening behavior of the metal according to the property of volume invariance in plastic deformation in coupling with the equilibrium and compatibility conditions. The computational methodology is realized with the laser powder fusion of maraging steel 350 as a material of example. The validation of the predictive models has been presented in terms of the comparison of predicted and measured scan-direction and build-direction residual stress distributions along depth of build under various process parameter combinations. Moreover, for the first time, the Jonson-Cook parameters of maraging steel 350 are predicted using analytical modeling of machining forces and non-linear optimization techniques.

Physics and neuroscience share overlapping objectives, the major of which is probably the attempt to reduce the observed universe to a set of rules. The approaches are complementary, attempting to find a reduced description of the universe or of the observer, respectively. We propose here that combining the two approaches within an observer-inclusive physical scheme, bears significant advantages. In such a scheme, the same set of rules applies to the universe and its observers, and the two descriptions are entangled. We show here that analyzing special relativity in an observer-inclusive framework can resolve its contradiction with the observed non-locality of physical interactions. The contradiction is resolved by reducing the universe (including the observer) to a dynamic distribution of closed strings (“ceons”) whose vibration waves travel at c. This ceons model is consistent with general relativity, non-locality, the holographic principle and loop quantum gravity; it also eliminates Zeno’s motion paradoxes. Yet, the model entails several new empirical predictions. Finally, the ceons model suggests a fundamental physical implementation of active biological perception. Paraphrasing Torricelli, this paper suggests that we live submerged in a c of light.

Performance appraisal is a fundamental indicator in public accountability to achieve the good governance principles. Hence, this study aims to analyze the performance measurement that can improve performance on government agencies in South Sulawesi, Indonesia. The study was conducted in qualitative approach. The research found that non-integrated models of performance measurement in South Sulawesi are inefficient and ineffective. Inefficiency happens because it uses time and cost resources separately, while being ineffective is because both models focuses on each goal instead on performance goals and the process is not supported by the actual management.

According to Copenhagen interpretation, a quantum particle can exist in a superposition of all possible states, out of which only one state is observed when it is measured. Interestingly, it has been observed that interaction with the quantum particle during measurement can also affect the outcome of the state. A scheme for interaction free measurement was proposed by Elitzur and Vaidman [Found. Phys. 23, 987 (1993)], where they used Mach Zehnder interferometer to detect whether a bomb is alive or dead. In 25 % of the cases they were able to detect that the bomb is alive without exploding it. Here, we demonstrate the above experiment using quantum computing, which can be realized in a quantum computer designing quantum circuits on it. We explicate all the cases, including whether the bomb is alive or dead by proposing new quantum circuits and executing those in QISKit as provided by IBM Quantum Experience platform and verify the obtained results.

Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

In this paper we show that the Schwarzschild radius can be extracted easily from any gravitationally-linked phenomena without having knowledge of the Newton gravitational constant or the mass size of the gravitational object. Further, the Schwarzschild radius can be used to predict any gravity phenomena accurately, again without knowledge of the Newton gravitational constant and also without knowledge of the size of the mass, although this may seem surprising at first. Hidden within the Schwarzschild radius are the mass of the gravitational object, the Planck mass (their relative mass), and the Planck length. We do not claim to have all the answers, but this seems to indicate that gravity is quantized, even at a cosmological scale, and this quantization is directly linked to the Planck units. This also supports our view that the Newton gravitational constant is a universal composite constant of the form $G=\frac{l_p^2{c}^3}{\hslash }$ , rather than relying on the Planck units as a function of G. This does not mean that Newton’s gravitational constant is not a universal constant, but that it is instead a composite universal constant that depends on the Planck length, the speed of light, and the Planck constant. Further, $\frac{G\times 1\hspace{0.17em}\mathrm{weight}\hspace{0.17em}\mathrm{unit}}{c^2}=\frac{G}{c^2}$ is the Schwarzschild radius off one weight unit. So G is only needed when we want to use gravity to find the weight of an object, such as weighing the Earth. This is, to our knowledge, the first paper that shows how a long series of major gravity predictions and measurements can be completed without any knowledge of the mass size of the object, or Newton’s gravitational constant. As a minimum we think it provides an interesting new angle for evaluating existing gravity theories, and it may even give us a small hint on how to combine quantum gravity with Newton and Einstein gravity.

Measurement-Device-Independent Quantum Key Distribution (MDI-QKD) is a two-photon protocol devised to eliminate eavesdropping attacks that interrogate or control the detector in realized quantum key distribution systems. In MDI-QKD, the measurements are carried out by an untrusted third party, and the measurement results are announced openly. Knowledge or control of the measurement results gives the third party no information about the secret key. Error-free implementation of the MDI-QKD protocol requires the crypto-communicating parties, Alice and Bob, to independently prepare and transmit single photons that are physically indistinguishable, with the possible exception of their polarization states. In this paper, we apply the formalism of quantum optics and Monte Carlo simulations to quantify the impact of small errors in wavelength, bandwidth, polarization and timing between Alice's photons and Bob's photons on the MDI-QKD quantum bit error rate (QBER). Using published single-photon source characteristics from two-photon interference experiments as a test case, our simulations predict that the finite tolerances of these sources contribute (4.04+/-20/N_sifted) to the QBER in an MDI-QKD implementation generating an N_sifted-bit sifted key.

This paper analyzes the measurement error, caused by the position of the current-carrying conductor, of circular array of magnetic sensors for current measurement. The circular array of magnetic sensors is an effective approach for AC or DC non-contact measurement, as its low cost, large linear range, wide bandwidth, light weight and low noise. Especially it has claimed that such structure has the excellent reduction ability for the errors caused by the position of the current-carrying conductor, crosstalk current interference, shape of the conduction cross section and the earth magnetic field. However, the positions of the current-carrying conductor, including un-center and un-perpendicularity, has not analyzed in detail until now. In this paper, the theoretical analysis has been proposed based on vector inner and exterior product. In the presented mathematical model of relative error, the un-center offset distance, the un-perpendicular angle, the radius of the circle and the number of the magnetic sensor are expressed in one equation. The comparison of the relative error caused by the position of the current-carrying conductor between four and eight sensors is conducted. The Tunnel Magnetoresistance (TMR) sensors are used in the experimental prototype to verify the mathematical model. The analysis results can be the reference to design the detail of circular array of magnetic sensors for current measurement in practical situation.

Sustainable Humanitarian logistics is gaining attention due to increased disasters. It involves various operations to support people's survival efforts. Key characteristics include unpredictable demand, sudden large demand volumes, high stakes in delivery timeliness, and limited resources. However, the complexity and unpredictability of disaster scenarios necessitate robust and adaptable performance measurement models to evaluate the effectiveness of sustainable humanitarian relief logistics (SHRL). This study proposes a novel performance measurement model for sustainable humanitarian logistics and supply chains that integrates the Fuzzy Delphi Method (FDM) and Fuzzy Decision-Making Trial and Evaluation Laboratory (Fuzzy-DEMATEL) method. In this research, using 115 articles focused on sustainable humanitarian logistics and supply chains, crisis management, and humanitarian aid, this research identified 25 key performance indicators (KPIs) in the initial phase. Following the implementation of FDM, 19 KPIs were identified as crucial for further analysis. These KPIs were then divided into four distinct categories: "Quality," "Accountability," "Operational Excellence," and "Sustainability". Initially, FDM is utilized to reach a consensus among experts concerning KPIs for humanitarian logistics and supply chains. By incorporating the inherent uncertainty and vagueness in expert judgments, FDM refines the list of key performance indicators that reflect the real-life conditions and constraints in disaster operations. Finally, the fuzzy DEMATEL approach was used to analyze interrelationships among factors, identifying cause-and-effect behavior and ranking them, forming a robust theoretical framework. The study concludes with the development of a comprehensive performance measurement model that facilitates the strategic planning and operational assessment of humanitarian organization operations. The integration of FDM and fuzzy DEMATEL methods offers multiple perspectives for decision-making and helps stakeholders identify critical areas for improvement. Based on the acquired results, the KPIs attached to the Quality (P1) aspect of the proposed framework have gained significant importance and main cause in the cause-and-effect relationship which impacts and is helpful to improve the performance of humanitarian organizations in all phases of disaster management. The KPIs prompt delivery (D1), and delivery accuracy (D2) are more significant, while capacity building and training (D19) and delivery compliance (D15) are least significant in SHRL scenarios. This research is expected to support humanitarian organizations in enhancing their capabilities, thereby improving the effectiveness and efficiency of aid delivery in disaster-stricken areas.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Keywords: early childhood; education; quality; measurement; monitoring; majority world; Item Response Theory; psychometrics

This study focuses on the impact of weak partial discharges (PDs) on defect recognition accuracy in epoxy resin through phase-resolved partial discharge (PRPD) analysis. Two measurement conditions are compared until PRPD pattern saturation: one-minute and one-hour durations. The PD data specifically target three void types located at different positions within the epoxy material. The aim is to evaluate how the presence of weak PDs at the PD extinction voltage (PDEV) influences defect recognition accuracy. This research sheds light on the potential implications of neglecting the significance of weak PD signals in defect detection. A convolutional neural network (CNN) model is trained using PRPD data recorded at the PD inception voltage (PDIV) and tested using the new PRPD data from both conditions recorded from a lower PDIV to a PDEV. The trained CNN model achieves a defect recognition accuracy of 100% for a one-hour duration, highlighting the importance of not neglecting weak PD signals. This emphasizes the significance of extended measurement duration and pattern saturation in capturing and analyzing weak PD signals for improved defect recognition. This study contributes to the advancement of practical applications by understanding the behavior of the epoxy material and enhancing defect detection techniques.

The article attempts to place the research within the broader context of urban living labs (ULLs) and highlights the significance of understanding success criteria by gathering data from key stakeholders associated with Basaksehir Living Lab, Bodrum Living Lab and Mezopotamya Living Lab via the in-depth interview method. However, there is a literature gap in terms of a comprehensive understanding of the success criteria specific to ULLs, which hinders the effective utilization of ULLs as platforms for addressing urban challenges. The conclusions drawn from the article emphasize the need for further examination of these labs' openness, user empowerment, and transferability criteria. Nevertheless, the article contributes to understanding the success criteria of ULLs and provides insights for future research and practice.

The mechanism of anionic/cationic combination collector ST-8 for the efficient separation of spodumene and feldspar was investigated by flotation tests, surface tension measurements, zeta potential measurements and infrared spectroscopy analysis. The flotation results indicated that when the optimum molar combination of sodium oleate and dodecylamine was 6:1-10:1 and pH=8.5 or so, the recovery of spodumene reached a maximum of 80% and that of feldspar reached about 24.5%. Zeta potential measurements showed that the negative shift of the kinetic potential on the surface of spodumene was much stronger than that on the surface of feldspar, indicating that the adsorption capacity of the combined collector on spodumene surface and feldspar surface was greatly different. From the surface tension as well as the synergistic parameters, there was a strong mutual attraction between dodecylamine and sodium oleate, and there was a significant synergistic effect between them. Infrared spectroscopy indicated that the combined collector chemisorbed on the mineral surface, and the intensity of the absorption peak after the action of spodumene was much stronger than that after the action of feldspar. The solution chemistry of the combined collector revealed that at pH 8.5, the positively charged ions RNH3+ and (RNH3+)22+ in dodecylamine and the negatively charged RCOO- and (RCOO-)22- ions in oleic acid form highly reactive complexes to interact with the mineral surface by electrostatic gravitation, thus achieving efficient separation of spodumene and feldspar. Finally, from the closed circuit test results, a flotation index of 6.34% Li2O grade and 88.51% Li2O recovery was obtained.

This paper discusses the use of networks of Inertial Measurement Units (IMU) for the reconstruction of trajectories from sensor data. Logistics is a natural application domain, to verify the quality of the handling of goods. This is a mass application and the economics of logistics impose that IMUs to be used must be low cost and use basic computational devices. The approach in the paper converts a strategy from the literature, used in the multi-target following problem, to reaching a consensus in a network of IMUs. The paper presents results on how to achieve the consensus in trajectory reconstruction, along with covariance intersection data fusion of the information obtained by all nodes in the network.

Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (30.5cm×22.5cm). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

The use of inertial measurement units (IMUs) to compute gait outputs such as the 3D lower limb kinematics is of huge potential, but no consensus on the procedures and algorithms exists. This study aimed at evaluating the validity of a 7-IMUs system against the optoelectronic system. Ten asymptomatic subjects were included. They wore IMUs on their feet, shanks, thighs and pelvis. The IMUs were embedded in clusters with reflective markers. Reference kinematics was computed from anatomical markers. Gait kinematics was obtained from accelerometer and gyroscope data after sensor orientation estimation and sensor-to-segment (S2S) calibration steps. The S2S calibration steps were also applied to the cluster data. IMU-based and cluster-based kinematics were compared to the reference through root mean square errors (RMSEs), centered RMSEs (after mean removal), correlation coefficients (CCs) and differences of amplitude. The mean RMSE and centered RMSE were respectively 7.5° and 4.0° for IMU-kinematics, and 7.9° and 3.8° for cluster-kinematics. Very good CCs were found in the sagittal plane for both IMUs and cluster-based kinematics at the hip, knee and ankle levels (CCs&gt;0.85). The overall mean amplitude difference was about 7°. These results reflected good accordance of our system with the reference, especially in the sagittal plane, but the presence of offsets requires caution for clinical use.

Calculation of the pressure field on and around solid bodies exposed to external flow is of paramount importance to a number of engineering applications. However, conventional pressure measurement techniques are inherently linked to problems principally caused by their point-wise and/or intrusive nature. In the present paper, we attempt to calculate the time-averaged two-dimensional pressure field by integrating PIV (Particle Image Velocimetry) velocity measurements into a CFD code and modifying them by the respective correction step of the SIMPLE algorithm. Boundary conditions are applied from the PIV data as a three-layer area of constant velocities, adjacent to the boundaries. A novel characteristic of the approach is the straightforward inclusion of the Reynolds Stresses into the source terms of the momentum equations, calculated directly from the PIV statistics. The methodology is applied to three regions of the symmetry plane parallel to the main boundary layer flow past a surface mounted cube. In spite of findings of deviations from the planar 2D flow assumption, the derived pressure fields and the adjusted velocity fields are found to be reliable, while the intrinsic turbulent nature of the flow is considered without modelling of the Reynolds stresses.

Light pen 3D vision coordinate measurement systems are increasingly widely used due to their advantages, such as small size, convenient carrying and wide applicability. The posture of the light pen is an important factor affecting accuracy. The pose domain of the pen needs to be given so that the measurement system has a suitable measurement range to obtain more qualified parameters. The advantage of the self-calibration method is that the entire self-calibration process can be completed at the measurement site without any auxiliary equipment. After the system camera calibration is completed, we take several pictures of the same measurement point with different poses to obtain the conversion matrix of the picture, and then use spherical fitting, the generalized inverse method of least squares, and the principle of position invariance within the pose domain range. The combined stylus tip center self-calibration method calculates the actual position of the light pen probe. The experimental results show that the absolute error is stable below 0.0737 mm and that the relative error is stable below 0.0025 mm. The experimental results verify the effectiveness of the method; the measurement accuracy of the system can meet the basic industrial measurement requirements.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

This study aims to explore the possibility of estimating a multitude of kinematic and dynamic quantities using subject-specific musculoskeletal models in real-time. The framework was designed to operate with marker-based and inertial measurement units enabling extensions far beyond dedicated motion capture laboratories. We present the technical details for calculating the kinematics, generalized forces, muscle forces, joint reaction loads, and predicting ground reaction wrenches during walking. Emphasis was given to reduce computational latency while maintaining accuracy as compared to the offline counterpart. Notably, we highlight the influence of adequate filtering and differentiation under noisy conditions and its importance for consequent dynamic calculations. Real-time estimates of the joint moments, muscle forces, and reaction loads closely resemble OpenSim's offline analyses. Model-based estimation of ground reaction wrenches demonstrates that even a small error can negatively affect other estimated quantities. An application of the developed system is demonstrated in the context of rehabilitation and gait retraining. We expect that such a system will find numerous applications in laboratory settings and outdoor conditions with the advent of predicting or sensing environment interactions. Therefore, we hope that this open-source framework will be a significant milestone for solving this grand challenge.

In cognitive radio systems, identifying spectrum opportunities is fundamental to efficiently use the spectrum. Spectrum occupancy prediction is a convenient way of revealing opportunities based on previous occupancies. Studies have demonstrated that usage of the spectrum has a high correlation over multidimensions which includes time, frequency, and space. Accordingly, recent literature uses tensor-based methods to exploit the multidimensional spectrum correlation. However, these methods share two main drawbacks. First, they are computationally complex. Second, they need to re-train the overall model when no information is received from any base station for any reason. Different than the existing works, this paper proposes a method for dividing the multidimensional correlation exploitation problem into a set of smaller sub-problems. This division is achieved through composite two-dimensional (2D)-long short-term memory (LSTM) models. Extensive experimental results reveal a high detection performance with more robustness and less complexity attained by the proposed method. The real-world measurements provided by one of the leading mobile network operators in Turkey validate these results.

In a recent paper [1], I argued against backward in time effects used by several authors to explain delayed choice experiments. I gave an explanation showing that there is no physical influence propagating from the present to the past and modifying the state of the system at a time previous to the measurement. However, though the solution is straightforward in the case of delayed choice experiments involving only one particle, it is subtler in the case of experiments involving two entangled particles because they give rise to EPR-like situations. Considering that a measurement is not an actual change of the physical state of a system and is relative to the observer allows to understand that there is neither backward in time effects nor instantaneous collapse of the second system when the first one is measured, as is often postulated. This allows also to get rid of any non-locality [2]. In this paper, I want to go further into the consequences of this way of considering the measurement, that I have called Convivial Solipsism, and show that even if, in the usual sense, there is no physical effect of the present or of the future on the past, we must nevertheless consider that the observer’s past is sometimes not entirely determined and that it becomes determined only when certain measurements are done latter. This apparent contradiction disappears if one understand that each observer builds, through her own measurements, her own world (that I call the phenomenal world in Convivial Solipsism) which is different from what we are used to consider as the common world shared by everybody.

This review and meta-analysis (PROSPERO registration number: CRD42020138845) critically evaluates test-retest reliability, concurrent validity and criterion validity of different physical activity (PA) levels of three most-common used international PA questionnaires (PAQs) in national language versions of EU-28: IPAQ-SF, GPAQ, and EHIS-PAQ. In total, 4969 abstracts were read, 287 full-text articles were identified as relvant to the study objectives, and 19 studies were included in the final meta-analysis. The studies’ results and quality were evaluated using the Quality Assessment of Physical Activity Questionnaires (QAPAQ) checklist. Results indicate that only five EU-28 countries validated national language versions of selected PAQs. Meta analysis revealed that assessment of moderate-to-vigourus PA (MVPA) is the most relevant PA level outcome, since no publication bias in any of measurement properties was detected while test-retest reliability was the moderately-high (rw=0.74), and moderate for both criterion (rw=0.41) and concurrent validity (rw=0.72). Reporting of methods and results of the studies was poor with overall moderate risk of bias with total score of 0.43. In conclusion, where only self-reporting is feasible, assessment of MVPA with selected PAQs in EU-28 adult population is recommended for policymaking.

The problem of real-time estimation of occupancy of buildings (number of people in various zones at every time instant) is relevant to a number of emerging applications that achieve high energy efficiency through feedback control. The measurement of CO2 concentration can be considered an important indicator that allows to define the occupation of closed and crowded spaces. Interesting cases can be school buildings and other buildings used in civil and residential (shopping centres, hospitals, etc.). This paper, starting from an experimental analysis in different classrooms of a University campus in real operating conditions, in different period of the year, proposes a possible correlation between CO2 concentration and the occupancy profile of the spaces. The acquired data are used to present some graphical correlations and to understand the most important variables or combination of them. Starting from an accurate analysis of the data, attempts are made to define a preliminary estimation method through the development of a mathematical models of occupancy dynamics in a building, which show interesting results.

Two major sample configurations are adopted in all the instruments for fabric hand measurement, flat sample as in KES and FAST types machines, and wrinkled sample as in PhabrOmeter. This paper compares the two sample types to examine which one if any offers a better coverage and reflection of the fabric sensory attributes. Fabrics have unique behaviors of drape, wrinkle and tactile sense which are entirely due to the simultaneous occurrence of both in-plane membrane deformation and out-of-plane bending deformation in multiple curvature. Such singular deformation mode cannot be detected by any machines using flat sample, whereas during a PhabrOmeter test, the fabric sample genuinely produces drape, wrinkle in addition to other related deformations. This paper then introduced the theoretical research pertaining to the measurement. Then a split sample experiment is conducted to demonstrate the importance of the internal connections in fabric during drape and wrinkle processes. As such fabric interconnection will be barely disclosed during tests using flat samples, another important advantage of PhabrOmeter is hence clearly shown.

Oscillometric blood pressure (BP) devices currently estimate a single point but do not identify fluctuations in BP or distinguish them from variations in response to physiological properties. In this paper, to analyze BP normality based on oscillometric measurements, we use statistical approaches including kurtosis, skewness, Kolmogorov-Smirnov, and correlation tests. Then, to mitigate uncertainties, we use a deep neural network (DNN) to determine the confidence limits (CLs) of BP measurements based on their normality. The proposed DNN regression model decreases the standard deviation of error (SDE) of the mean error (ME) and the mean absolute error (MAE) and reduces the uncertainty of the CLs and SDEs of the proposed technique. We validate the normality of the distribution of the BP estimation distribution which fits the Gaussian distribution very well. We use a rank test in the DNN regression model to demonstrate the independence of the artificial SBP and DBP estimations. First, we perform statistical tests to verify the normality of the BP measurements for individual subjects. The proposed methodology provides accurate BP estimations and reduces the uncertainties associated with the CLs and SDEs based on the DNN regression estimator.

External hoof characteristics, balance, and conformation have been extensively studied in horses; however, mules remain understudied in these aspects. This study evaluated the size, shape, and symmetry of untrimmed and unshod forelimb hooves, compared the symmetry between forelimb hooves and stratified external forelimb hoof measurements based on the body condition score of mules raised in the foothill plains of northern Thailand. The forelimb hooves of 38 mules were photographed and 33 parameters, including angular and linear measurements, were analyzed. Despite the absence of shoeing and trimming, these mules exhibited optimal left-right forelimb hoof symmetry, with no significant (p < 0.05) differences in: outer wall length and inner wall length (OWL - IWL); sole length and sole width (SLS - SW); dorsal hoof wall length and heel length (DHWL - HL); and frog length and frog width (FL - FW). However, significant (p < 0.05) differences were observed within each body condition score group for forelimb hoof measurements for DHWL, IWL, heel separation (HS), heel bulb distance (HBD), SW, FW, and FL. These findings provide valuable insights into mule welfare and management, contributing to understanding of the interplay between overall health and hoof conformation in the study area.

The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

The paper presents the basic structural parts, a 3D model and the overall design of a laboratory machine, which was created to detect vibrations generated by the casing of a conveyor roller ro-tating at different speeds. The intention of the authors was to verify whether plastic brackets in-serted into the structurally modified trestles of a fixed conveyor idler can reduce the vibration values transmitted from the rotating conveyor roller to the trestle of a fixed idler. Experimental vibration measurements taken on the non-rotating parts of conveyor rollers, performed on a laboratory machine according to ISO 10816, are suitable for characterizing their operating condi-tions with regard to trouble-free operation. The aim of this paper is to detect the vibrations of a rotating conveyor roller on a laboratory machine in the defined places of a fixed conveyor idler and also on the steel frame of a laboratory machine that represents the supporting track of a belt conveyor. Vibrations detected by piezoelectric acceleration sensors were recorded by a measur-ing apparatus and displayed in the environment of Dewesoft X software. The measurements show that the vibration values grow with the increasing speed of the conveyor roller rotation. Experimental measurements have proven the correctness of the assumption that the vibrations transmitted to the trestle of a fixed conveyor idler are lower by up to 40% when using plastic brackets into which the axle of the conveyor roller is attached, compared to the solution where the axle of the conveyor roller is inserted into the notches of a steel trestle.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

Two algorithms of data processing are proposed to shorten the unmeasurable dead-zone close to the zero-position of measurement, i.e., the minimum working distance of a dispersive interferometer using optical frequency comb, which is a critical issue in millimeter-order short-range absolute distance measurement. After demonstrating the limitation of the conventional data processing algorithm, the principles of the proposed algorithms, namely the spectral fringe algorithm, and the combined algorithm that combines the spectral fringe algorithm with the excess fraction method, are presented, together with simulation results for demonstrating the possibility of the proposed algorithms for shortening the dead-zone with a high accuracy. An experimental setup of dispersive interferometer is also constructed for implementing the proposed data processing algorithms over spectral interference signals. Experimental results demonstrate that the dead-zone by the proposed algorithms can be as small as half of that by the conventional algorithm while the measurement accuracy can be further improved with the combined algorithm.

The time interval set approach depends on results for radiation propagation from star sources, where properties relate to sphere like propagation surfaces, finite for any realistic event and measurement. In contrast usually applied to stationary and parallel propagation is the traditional vector and one moment time coordinate kinematic approach from Newton’s laws. A time interval only description necessarily has to start from it's own definitions, and properties since time intervals have to be defined with time intervals. In this paper studied are time interval only set properties, commutation, addition and multiplication, and derivatives, and how to define these corresponding consistently with one moment time set properties. Time development and equilibrium within the time interval description depend on the well-known ‘mean velocity theorem’ and the time interval version of the Legendre transform. Radiation propagation ‘away from’ and gravitation ‘towards’ the star source are part of the one time interval description. In the second, discussion, part the time interval only set approach with only the fundamental properties is applied to radiation. Included is a derivation of star source radiation energy for both zero and non zero wave particle mass. The time interval set is not one of the usual sets encountered and the canonical property does not apply, the approach in this paper starts from commutation properties of one moment time coordinates and of time intervals and relates to Noether charges and structure constants. These are found to be equal to the radiation wave group-velocity, for photons the light velocity c, and, different from the usual derivative to one moment time, they equal specific arguments of the time interval only set derivative.

In this contribution, we present a high-speed multiplex grating spectrometer based on a spectral coding approach that is founded on principles of compressive sensing. The spectrometer employs a single-pixel InGaAs detector to measure the signals encoded by an amplitude spatial light modulator (digital micromirror device, DMD). This approach leads to a speed advantage and multiplex sensitivity advantage atypical for standard dispersive systems. Exploiting the 18.2 kHz pattern rate of the DMD, we demonstrate 4.2 ms acquisition times for full spectra with a bandwidth of 450 nm (5250 cm-1 – 4300 cm-1; 1.9 µm – 2.33 µm). Due to the programmability of the DMD, spectral regions of interest can be chosen freely, thus reducing acquisition times further, down to the sub-millisecond regime. The adjustable resolving power of the system accessed by means of computer simulations is discussed, quantified for different measurement modes, and verified by comparison with a state-of-the-art Fourier-transform infrared spectrometer. We show measurements of characteristic polymer absorption bands in different operation regimes of the spectrometer. The theoretical multiplex advantage of 8 was experimentally verified by comparison of the noise behavior of the spectral coding approach and a standard line-scan approach.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.