By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

The aim of this study is to introduce a novel method which can separate sand or gravel dominated bed load transport in rivers with mixed-size bed material. In engineering practice, the Shields-Parker diagram could be used for such purposes, however, the method has certain applicability limits, due to the fact that it is based on uniform bed material and provides information rather on river-scale, instead of reach or local scale. When dealing with large rivers with complex hydrodynamics and morphodynamics the bed load transport modes can also indicate strong variation even locally, which requires a more suitable approach to estimate the locally unique behavior of the sediment transport. Here, we suggest that the decision criteria utilizes the shear Reynolds number (Re*). The method was verified against field and laboratory measurement data, both performed at non-uniform bed material compositions. The comparative assessment of the results show that the shear Reynolds number based method operates more reliably than the Shields-Parker diagram and it is expected to predict the sand or gravel transport domination with a < 5% uncertainty. The introduced results can greatly contribute to the improvement of numerical sediment transport modeling as well as to the field implementation of bed load transport measurements.

The article is dedicated to addressing the current challenge of augmenting the load- bearing ca-pability of pile foundations. This predicament is most effectively addressed by employing piles with unconventional geometries, along with atypical methodologies for installing these foun-dation piles. The primary objective of research is to examine the impact of various fill materials (including both soil and rigid substances) on the energy consumption during pile driving and the resistance to static loads by piles with multiple shaft expansions. The findings derived from model-based investigations demonstrate that the load-bearing capacity of piles with shaft ex-pansions, installed with bulk material filling, surpasses that of conventional piles (prismatic and pyramidal) by a factor ranging from 1.5 to 4.6. Furthermore, the research outcomes also indicate greater energy consumption (1.14-1.66 times) and enhanced load-bearing capacity (1.15-1.68 times) for piles with shaft expansions driven with backfill, in comparison to piles installed without backfill. It is noteworthy that the type of backfill material significantly influences the energy consumption during pile driving and their stability under axial static loads. The correla-tion relationships can be applied to approximate projection of the energy-related and structural parameters of piles with shaft expansions embedded with the addition of bulk materials.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

For many engineering applications it is sufficient to use the concept of simple materials. However, higher gradients of the kinematic variables are taken into account to model materials with internal length scales as well as to describe localization effects using gradient theories in finite plasticity or fluid mechanics. In many approaches length scale parameter have been introduced that are related to a specific micro structure. An alternative approach is possible, if a thermodynamically consistent framework is used for material modelling as shown in the present contribution. However, even if sophisticated and thermodynamically consistent material models can be established there are still not yet standard experiments to determine higher order material constants. In order to contribute to this ongoing discussion system identification based on the method of self-adaptive filtering is proposed in this paper. To evaluate the effectiveness of this approach it has been applied to second-order gradient materials considering longitudinal vibrations. Based on thermodynamically consistent models that have been solved numerically it has been possible to prove that system identification based on self-adaptive filtering can be used effectively for both narrow-band and broadband signals in the field of second-order gradient materials. It has also been found that the differences identified for simple materials and gradient materials allow for condition monitoring and detection of gradient effects in the material behavior.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Dampers provide safety by control of unwanted motion, due to conversion of mechanical work into another form of energy (e.g., heat). State of the art materials are elastomers including thermoplastic-elastomers. For polymer-appropriate replacement of multi-component shock absorbers comprising mounts, rods, hydraulic fluids, pneumatic devices, or electro-magnetic devices, among others, deep insights of the dynamic thermo-mechanical characteristics of damper materials have to be gained. The ultimate objective is to reduce complexity by utilizing inherent material damping rather than structural (multi-component) damping properties. The objective of this work was to compare the damping behavior of different elastomeric materials including thermoplastic poly(urethane) (TPU), and silicone rubber blends (mixtures of different poly(dimethylsiloxane) (PDMS)). Therefore, the materials were hyper- and viscoelastic characterized, a finite element calculation of a ball-drop test was performed, and for validation the rebound resilience was measured experimentally. In an attempt, the coil-over shock absorber of a model car was replaced by a damper made of the examined and modeled materials. The results revealed that the material parameter determination methodology is reliable, and the data applied for simulation lead to realistic predictions. Interestingly, the rebound resilience of the mixture of soft and hard PDMS (50:50)w% is the highest and the lowest values were measured for TPU.

In this study, literature on pore structure and chloride ion diffusivity was collected to investigate the correlation of pore structure indicators with diffusivity. Good correlation between total porosity and chloride ion diffusivity was found when the samples did not contain admixture materials and diffusion test was conducted without acceleration. Pore diameter indicators did not correlate with diffusivity. The diffusivity of cement paste was reduced by admixture materials compared to that without admixture materials even if the total porosity is the same. On the other hand, the diffusivity of concrete was not reduced by admixture materials.

Advanced composite materials have drawn significant interest in the last years as an alternative to traditional materials due to their higher performance. However, industry struggle to provide low-cost, higher occupational safety, lower footprint with composites, making them suitable for holistic analyses. Therefore, the material design becomes an essential element that can impact the competitiveness, particularly in terms of productivity, circularity, safety, sustainability, and quality of the value chain. The Material Design-for-eXcellence is a state-of-art methodology for material performance multi-dimensional assessment along its life cycle phases, either useful to support ma-terial selection for new products or also to new material design support optimizing resource effi-ciency. In this methodology, the material behaviour and its multiple characteristics assessment, and the manufacturing processes efficiency are evaluated. The framework considers the analogy of product design holistic approaches, as Lean Design-for-X, to organize and assess the mul-ti-dimensional performance for each “X” Material Property. In this work, it was possible to observe that the bio-based composites solutions could be a good sustainable alternative for several sectors. Every day researchers are creating more new materials, having a diversity of properties at different scales, Material Design-for-eXcellence must also in the near future consider other factors. Hence, additional studies are thus foreseen to explore and develop this new tool.

This paper describes a new approach that can be used to determine the mechanical properties of unknown materials and complex material systems. The approach uses inverse finite element modelling (FEM) accompanied with a designed algorithm to obtain the modulus of elasticity, yield stress and strain hardening material constants of an isotropic hardening material model, as well as the material constants of the Drucker-Prager material model (modulus of elasticity, cap yield stress and angle of friction). The algorithm automatically feeds the input material properties data to finite element software and automatically runs simulations to establish a convergence between the numerical loading-unloading curve and the target data obtained from continuous indentation tests using common indenter geometries. A further module was developed to optimise convergence using an inverse FEM analysis interfaced with a non-linear MATLAB algorithm. A sensitivity analysis determined that the dual Spherical and Berkovich (S&B) approach delivered better results than other dual indentation methods such as Berkovich and Vickers (B&V) and Vickers and Spherical (V&S). It was found that better convergence values can be achieved despite a large variation in the starting parameter values and / or material constitutive model and such behaviour reflects the uniqueness of the dual S&B indentation in predicting complex material systems. The study has shown that a robust optimization method based on a non-linear least-squares curve fitting function (LSQNONLIN) within MATLAB and ABAQUS can be used to accurately predict a unique set of elastic plastic material properties and Drucker-Prager material properties. This is of benefit to the scientific investigation of properties of new materials or obtaining the material properties at different location of a part which might be not be similar due to manufacturing processes (e.g. different heating and cooling rates at different locations).

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

Microencapsulation using polymer materials is a potent process to protect and prolong the survival of probiotics. Cissampelos pareira leaf contains natural gelling agents that possess solidifying properties. This study aimed to investigate the development of microencapsulation containing Lacticaseibacillus paracasei using C. pareira extract as a natural encapsulating material. The absorption bands near 1603 cm−1 and 1725 cm−1 detected by Infrared spectroscopy (FTIR) were identified as pectin in C. pareira structure. The L. paracasei-C. pareira microcapsules (LP-CP) showed high encapsulation efficiency by 90.5% which was confirmed by the evaluation of their survival rate. Under thermal conditions (85oC), bacterial viability detected in the microcapsules was 69% as opposed to non-encapsulated bacteria where viability was as low as 5%. Furthermore, the microcapsule presented 75% bacterial viability whereas the free cells showed 30% under acidic conditions (pH 2). During storage conditions, LP-CP viability remained at 50% when the storage time was extended to 90 days whereas, the survival rate of free cells significantly decreased by 100% after 90 days. This information suggests that C. pareira is a potent polymer which can be used as an eco-friendly material for the microencapsulation of probiotics relevant as dietary supplementation for humans or animals.

This article illustrates a comprehensive exploration of the multifaceted role of hydrocarbons in the field of material science, bridging the gap between theoretical understanding and practical applications, also providing acumens into future perceptions. Hydrocarbons, which consists of hydrogen and carbon atoms, play a critical role in numerous sectors due to their extensive presence in both natural and synthetic environments. The study categorizes hydrocarbons into diverse categories such as alkanes, alkenes, alkynes, and aromatic hydrocarbons, each owning unique features that influence their physical properties and applications. This inclusive review comprehends the fundamental aspects of hydrocarbons, their indispensable compounds and elements, and their substantial contributions to material science, including their utilization in coatings, composites, and polymers. Besides, the article investigates into case studies that demonstrate the theoretical advancements and practical applications of hydrocarbons, as well as their latent in addressing future energy and environmental encounters. By investigative the role of hydrocarbons in the expansion of innovative materials and their implications for sustainability and technological progress, the article accentuates the significance of hydrocarbons in evolving the field of material science and technology.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

Background: Despite the fact that bone reconstructive surgeries are widely practiced worldwide, the search for an ideal bone replacement matetrial is still an open issue. We aimed to provide an overview of the current status of research and developments in this field with a focus on sapphire materials; Methods: A literature search and review was conducted using the PubMed, Scopus, and Embase databases. We searched for literature using the following keywords: bone implants; biocompatible materials; bone replacement material; sapphire implants; Results: Sapphire has a unique combination of mechanical, physical and chemical characteristics thanks to wich it has an excelent biocompatability and biointegrity.Unlike other materials it is incredibly strong and has a high endurance. The successful experience of using this material in medical instrument engineering, dentistry and cardiac surgery shows its benefits; Conclusions: We consider that sapphire is a perspective material for bone replacement implants and researchers should look in this direction.

During the last decade, smart materials have increasingly impacted on several niches, among which that of one-off/limited edition experimental fashion. Thanks to their performativity, due to the implementation of Smart Materials Systems, they have reached indeed catwalks as well as museums and galleries. As boundaries between what-is-art and what traditionally was not supposed to be art are now turning into osmotic membranes, zooming on how smart materials are highly contributing to outline the new creative landscape can provide with interesting and compelling issues. Introducing three different areas of experimental fashion, named Multi-sensory dresses, Empathic dresses, and Bio-smart dresses and accessories, respectively covering the world of in-Lab experiments and design collaborations in relation to the application of advanced smart materials systems, the article discuss some of the implications in term of Design Thinking and Design Aesthetics.

Saccharomyces cerevisiae (S. cerevisiae) ethanol fermentation has left an indelible trace in human history. It is regarded as the original beverage synthesis, and has developed into an essential energy supply for mankind today. However, the history of ethanol synthesis using S. cerevisiae, including the mechanism analysis process, has not been carefully and succinctly reported. In this paper, we review the history of ethanol synthesis using S. cerevisiae. In addition, we also review the substrates that drive S. cerevisiae ethanol synthesis, including the utilization of glucose, sucrose, starch and molasses, in order to summarize the current development status and to contribute to the further improvement of this field.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.

Mining is an important industry, accounting for 6.9% of global GDP. However, global development promotes accelerated demand, resulting in the accumulation of hazardous waste in land, sea, and air environments. It reached 7 billion tonnes of mine tailings generated yearly worldwide, and 19 billion solid tailings will be accumulated by 2025. Adding to this, the legacy of environmental damage from abandoned mines is worrying; in Canada there are around 10,000 abandoned mines, 50,000 in Australia, 6,000 in South Africa, and 9,500 coal mines in China, reaching 15,000 by 2050. In this scenario, restoration techniques from mining tailing have become increasingly discussed among scholars due to their potential to offer benefits towards reducing tailings levels, thereby reducing environmental pressure for the correct management and adding value to previously discarded waste. This review paper explores available literature on the main techniques of mining tailing recycling and reuse and discusses leading technologies, including the benefits and limitations, as well as emerging prospects. The findings of this review serve as a supporting reference for decision-makers concerning the related sustainability issues associated with mining, mineral processing, and solid waste management.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity or remain stress-free. Contrary to this are shell structures, which can bridge large spans with little material if designed well. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behaviour on a smaller scale by dissolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is to be developed in an ongoing research project, basic analysis approaches of which are presented in this paper. In addition to the basic workflow and the programs used, the material models used, and their calibration are described on the basis of tests on textile reinforced concrete (TRC) samples. Initial tests on two individual TRC served to verify the model.

Simulation programs contain Computational Fluid Dynamics - CFD codes and are a useful tool used for gas flow through porous materials. Conducting numerical simulations allows for detailed analysis of hydrodynamic phenomena. The results of numerical modeling should always be verifiable based on experimental data. Only their compliance with the results of experimental tests is a determinant of the correctness of the applied method. As part of the work, experimental studies of hydrodynamics of gas flow through an isotropic porous material were carried out and numerical simulation for material of the same shape was used. In the CFD modeling Kolmogorov's hypothesis for the transport of kinetic energy of turbulence k and transport of dissipation rate of kinetic energy of turbulence ε was used.

This study aimed to investigate the impact of incorporating Refuse Derived Fuel (RDF) into a production brick mixture in order to mitigate difficulties encountered in the production environment. Three distinct tests were conducted to assess the preparation process. The first test served as a reference, utilizing 100% clay material without RDF. The second test involved the inclusion of 10% RDF, obtained from a waste factory, with a grain size less than 20mm. In the third test, the RDF was mixed with silica sand after undergoing hammer milling with a 2mm sieve, followed by a 10% incorporation into the mixture. The primary objective was to comprehend the behavior of these mixtures in two critical stages: extrusion and drying. Extrusion performance was evaluated by examining the shaping process from the mold, vacuum conditions within the extruder, and the cutting of wet sample bricks. Furthermore, the drying procedure was assessed in terms of shrinkage, drying sensitivity, and appearance. Comparisons were made among the three test scenarios to identify the influence of RDF on these key parameters. Preliminary results indicate that the inclusion of RDF impacted the extrusion process. The addition of RDF resulted in variations in the flow characteristics of the mixture, affecting the shape formation from the mold and the vacuum conditions within the extruder. Additionally, the cutting of wet sample bricks exhibited some differences compared to the reference test. Concerning the drying phase, the presence of RDF influenced shrinkage behavior and drying sensitivity. The mixture with RDF showed different shrinkage patterns compared to the reference, and its drying sensitivity was altered. Moreover, the appearance of the bricks after drying exhibited notable variations due to the incorporation of RDF. In conclusion, incorporating RDF in the brick mixture introduces changes in both the extrusion and drying stages. The alteration in flow characteristics and vacuum conditions during extrusion, as well as the variations in shrinkage, drying sensitivity, and appearance during drying, suggest that further investigation is necessary to optimize the incorporation of RDF for improved brick production. These findings contribute to the understanding of the challenges and opportunities associated with the utilization of RDF in brick manufacturing processes.

The material derivative is important in continuum physics. This Letter shows that the expression $\frac{d }{dt}=\frac{\partial }{\partial t}+(\bm v\cdot \bm \nabla)$, used in most literature and textbooks, is incorrect. The correct expression $ \frac{d (:)}{dt}=\frac{\partial }{\partial t}(:)+\bm v\cdot [\bm \nabla (:)]$ is formulated. The solution existence condition of Navier-Stokes equation has been proposed from its form-solution, the conclusion is that "\emph{The Navier-Stokes equation has a solution if and only if the determinant of flow velocity gradient is not zero, namely $\det (\bm \nabla \bm v)\neq 0$.}"

Ultrasonic based inspection of thin-walled structures often requires prior knowledge of their mechanical properties. Their accurate estimation could be achieved in a non-destructive manner employing, e.g., elastic guided waves. Such procedures require efficient approaches for experimental data extraction and processing, which is still a challenging task. An advanced automated technique for material properties identification of an elastic waveguide is proposed in this investigation. It relies on the information on dispersion characteristics of guided waves, which are extracted by applying the matrix pencil method to the measurements obtained via laser Doppler vibrometry. Two objective functions have been successfully tested, and the advantages of both approaches are discussed (accuracy vs computational costs). The numerical analysis employing the synthetic data generated via the mathematical model as well as experimental data shows that both approaches are stable and accurate. The influence of the presence of various modes in the extracted data is investigated. One can conclude that the influence of the corruptions related to the extraction of dispersion curves is not critical if the majority of guided waves propagating in the considered frequency range are presented. Possible extensions of the proposed technique for damaged and multi-layered structures are also discussed.

The massive use of electronic equipment has raised concerns about electromagnetic (EM) pollution, leading to increased attention to EM shielding in both civil and military applications. EM absorption materials play a crucial role in reducing the energy of microwaves projected onto their surface. In this work, we propose a novel OTA (over-the-air) antenna test method to evaluate and analyze the functionality of EM absorption materials. This method offers a new and practical way to assess the effectiveness of these materials. Measured results indicate that the presence of the EM absorption material led to a decrease in antenna gain of approximately 2-3 dB, a reduction in efficiency of more than 10-15%, and a smaller radiation pattern during the actual testing process. These findings highlight the impact of EM absorption materials on antenna performance. Compared to the traditional S-parameter testing method, the gain comparison testing method exhibits the advantages of higher accuracy and simpler operation in the lower frequency experiment.

The hard-shelled seed industry plays an important role in the global agricultural economy. As a result of nut industrialization, considerable amounts of by-products and residues are produced year by year, burnt as fuel or discarded as non-valued waste, by-passing a potential source of valuable compounds or features. Over the last decade nutshells have received great interest due to their lignin concentration and their antioxidant, physical and mechanical features. It was found that these properties vary among cultivars, latitude and localities of plantation. On the other hand, there is inconsistences regarding to mechanical and some biochemical properties of both nutshells, which aimed to explore the status of potential hazelnut and walnut shells appli-cations into sustainable circular bio-economy chains. Hence, this review deals with the recent scientific literature on their chemical composition as well as their functional applications as an approach to sustain the utilization of the main by-product derived from the nut-industry.

Due to satisfactory mechanical properties, low specific weight and other advantages, a substantial utilization of laminated structural composites in many components and equipments of several industry sectors, especially in the past two decades, has been made. This class of materials has a good potential to be an important ally to support scientists and engineers with the main current world challenge: an energy transition process that must occur with sustainability, eco-friendly materials and based on an efficient reduction of greenhouse gas emissions. In this context, a microanalysis (scale length: 10μm to 1mm) of mechanical behavior that considers the multiphase characteristics, at leastwise a matrix and a reinforcement phase, of this kind of composites must be explored, i. e., a heterogeneous material is assumed to predict, for example, the effective tensors of stiffness or compliance by a homogenization process, modeling to damage analyses, studies about progressive delamination and other specific aspects of a composite can be previously investigated using micromechanical approaches. Therefore, the understanding of fundamental micromechanics as well as some advanced models are essential to apply these materials in structural industry components. In this sense, this systematic literature review is designed to investigate the main basic and advanced models of laminated composites micromechanics and using this overall study, have been developed, in the end, an analysis of research trends to the topic, in which, lines to future researches are indicated.

specific finite detail modeling of the human body gives a capability primary enhancement to the prediction of damage risk all through automobile impacts. currently, car crash protection coun-termeasure improvement is based on an aggregate of testing with installed anthropomorphic check devices (i.e., ATD or dummy) and a mixture of multibody (dummy) and finite element de-tail (vehicle) modeling. If an incredibly easy finite element detail version can be advanced to cap-ture extra statistics beyond the abilities of the multi-body structures, it might allow advanced countermeasure improvement thru more targeted prediction of overall performance. Numerous research have been done on finite element analysis of broken femurs. However, there are two missing pieces of information: 1- choosing the right material properties and 2- designing a precise model including the inner structure of the bone. In this research, most of the chosen material properties for femur bone will be discussed and evaluated.

Foam concrete is a construction material with controllable low strength and untraditional physical properties. Its highly crushable nature leaves it a niche as an engineered energy-absorbing material in many value-added applications; however, fundamental understanding of the material properties is crucial. As foam concrete is highly cellularized and ductile, conventional concrete testing methods such as compression test are insufficient to characterize the key material attributes of foam concrete, especially when the foam density is low. The resonant frequency test (ASTM C215) is specified for evaluating dynamic Young’s modulus of normal concrete. Inspired by the non-destructive feature of this test, we investigate the possibility of using the resonant frequency test to continuously monitor the modulus build-up of foam concrete with age. For the representativeness of the samples, three variables are considered in material design—bulk density ranging from 0.4 to 1.2 g/cm3, water to cementitious materials ratio of 0.42 and 0.47, and fly ash replacement of 10 and 30% by weight of cement. After examining the different vibration modes, the fundamental transverse frequency is determined most suitable for interpreting the foam modulus. The experimental results demonstrate good accuracy of using this approach for the measurement of different samples. It is also confirmed that, for a given foam concrete, the foam modulus can be predicted by knowing the foam density and solid modulus of its base cement paste, which provides an important insight for the further studies and real applications of foam concrete.

The sensitivity of macroscopic mechanical and thermal properties of grey cast iron is computationally investigated for a variety of graphite microstructures over a wide temperature range. In order to represent common graphite microstructures according to DIN EN ISO 945-1, a synthetic approach is used to algorithmically generate simulation domains. The developed mechanical and thermal model is applied in a large simulation study. The study includes statistical volume elements of the graphite microstructures classes GG-15 and IA2 to IA5, with 10 v.-%, 11 v.-% and 12 v.-% graphite, respectively, for a temperature range from 20 °C to 750 °C. Homogenized macroscopic quantities such as the Young's moduli, Poisson's ratios, yield strengths and thermal conductivities are predicted for the different microstructure classes by applying simulation and data analysis tools of the research data infrastructure Kadi4Mat.

Considering the current energy environment, both efficient and environmentally friendly solutions have to be developed for building construction. Bio-based building materials offer new perspectives through their insulating and natural humidity regulation capacities. Nevertheless, these materials are as complex as they are promising and grey areas still remain regarding their behavior. Their water sorption and desorption curves recorded in experimental work demonstrate a hysteresis phenomenon and, although plausible hypotheses have been formulated in the literature, there is currently no consensus on its causes. Furthermore, it is important to emphasize that no reference considers the hydrophilic nature of the resource. Yet this is a specificity of raw material coming from the plant world. In this context, this paper explores the microstructure and chemical composition of plant aggregates to propose a new explanation for the hysteresis. It is based on recent work demonstrating the existence of differentiated hydrogen bonds between the water sorption and desorption phase in cellulose. Obviously, hysteresis also has an origin at the molecular scale. Lastly, the hypothesis put forward here is supported by the swelling of bio-based materials that has been observed at high relative humidity and this study aims to identify a link between the mechanical (swelling/shrinking) of bio-based materials and their hygroscopic behavior. This leads to a better understanding of the hydro-mechanical coupling of these materials.

The popularity and growth of additive manufacturing(AM) in recent years are due to its ability to provide innovative solutions to complex manufacturing challenges and its potential to transform the way products are designed, developed, and produced. In this work, the numerical simulation geometry of the model extruder from nozzle is established along with the material extrusion process. The high gravity material extrusion system (HG-MEX) properties and characteristics during filament fabrication are evaluated. This work investigates the effects of gravity on the material extrusion process from nozzle extrusion. This work is unique in the incorporation of fluid surface characteristics to represent the performance and contact with the material extrusion in additive manufacturing. The use of simulation in high gravity material extrusion in additive manufacturing is a meaningful and valuable approach to improving the quality and efficiency of the process.

The Odunpazarı Modern Museum (OMM), conceptualized by Architect Kengo Kuma and inaugurated in 2019 in Eskişehir, stands as a testament to the historical significance of the timber trade in the region. The deliberate choice of wood as the primary construction material serves as a tribute to this historical narrative. The conspicuous incorporation of wooden lath materials into both the external and internal spaces signifies a conscious reference to the region's historical heritage and aligns with sustainability principles in design. The timber used to construct OMM was sourced from exhausted industrial pine forests. The creation of exhibition spaces at diverse scales involved the assembly of boxes of varying dimensions, illustrating OMM's inclination towards a formative structure characterized by “Addition and Integration.” This architectural methodology involves juxtaposing two or more primary forms to achieve a partial amalgamation. Factors such as form characteristics, dimensional distinctions, spatial arrangements, and extent of surface interactions collectively contribute to the compelling effect of this integrative approach. Within the confines of the museum, unconventional partitioning is implemented, and the strategic arrangement of masses results in multiple façades, even in the absence of overt wooden surfaces. The discernible visibility of the building's façade from an internal vantage point underscores the pivotal role played by wood in the architectural design of the OMM. The exterior impact of the wooden shell complements its interior application. The voluminous void at the heart of the structure allows for the infiltration of natural light into the internal spaces, and the wooden facade facilitates the transmission of light. The use of glass to segregate the cafeteria area from the museum entrance preserves a visual continuity between these spaces. The fundamental research inquiry in this study revolves around the user experience of wood, a material that actively influences diverse facets, including structural elements, contextual considerations, interior arrangements, and external aesthetics. To address this inquiry, a comprehensive case study and survey were conducted with the objective of elucidating the functional, sensory, perceptual, and psychological impacts of wood, the primary material in the museum's spatial configuration, on the overarching user experience.

Two-dimensional (2D) semiconductors like Transitional Metal Dichalcogenides (TMDCs) have attracted strong research interest in the last decade. Unlike the more celebrated 2D material graphene, TMDCs like molybdenum disulfide(MoS₂) possess bandgap. The number of layers critically depends on the band structure of MoS₂. For example, it is indirect for bulk MoS₂. However, it becomes direct bandgap material for a monolayer MoS₂. Monolayer MoS₂, therefore, becomes an important material for photoelectronic devices. An essential aspect of such devices is the metal-semiconductor junction. Metal-TMDC junction is, therefore, a well-studied interface due to its importance for 2D materials-based photoelectronic devices. Most importantly, it can be flexible, stretchable to it’s length, and bent to a large angle. We used metals like Au and Al to interface with TMDs like MoS₂. We used silicon and PDMS as substrates. So, we have to focus on investigating the relative properties of various TMDCs. We see change in band energy and vibrational modes via Photoluminiscence and Raman spectroscopy as shown in the article. However, certain aspects are yet to be explored, for example, how this interface behaves in the presence of strain.

Paraffin wax stores energy in the form of latent heat at a nearly constant temperature during melting and releases this energy during solidification. This effect is used in industrial energy storage. An unusual change in the shape of a melted droplet of paraffin wax placed on a relatively cold glass plate is studied. As the droplet solidifies, its upper surface becomes nearly flat and a dimple is formed in the center of this surface, making the droplet look like a fruit (pumpkins are more commonly shaped like this, but the authors prefer apples). A series of experiments, as well as physical and numerical modeling of the droplet's thermal state, taking into account the formation of a mushy zone between liquidus and solidus, made it possible to understand the role of gravity and gradual increase in viscosity and density of paraffin wax on changing the droplet shape and, in particular, to clarify the mechanism of formation of the dimple on its upper.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

During the explosion of energetic materials, obvious electromagnetic interference will be generated, which will affect the normal operation of surrounding electronic equipment. Experiments are still an important means to study this issue. A set of electromagnetic radiation measurement device based on short-wave omnidirectional antenna and ultra-wideband omnidirectional antenna is designed to measure the electromagnetic radiation generated by the explosion of energetic materials of different masses, and the electromagnetic radiation characteristics are obtained through data processing. The results show that the mass of the energetic material has a significant effect on the time-domain characteristics of the electromagnetic radiation generated by the explosion: the higher the mass of the energetic material, the shorter the delay response of the electromagnetic signal, the longer the duration, and the earlier the peak appears. The frequency of electromagnetic radiation signals generated by the explosion of energetic materials is mainly concentrated below 100 MHz, and the energy is most concentrated in the frequency band of 0~50 MHz. The composition of energetic materials has the greatest influence on the spectral distribution, and the spectral distribution of electromagnetic radiation produced by the explosion of explosives with different compositions has obvious specificity. The electromagnetic radiation intensity generated by the explosion of energetic materials has a strong correlation with the distance from the explosion center, and it decreases with the increase of the distance, and the decreasing range is large. The structure and detonation method of energetic materials can change the geometrical motion mode during the explosion, resulting in the non-uniformity of electromagnetic radiation propagation.

The effects of the dielectric constant of the powder phase on lead zirconate titanate (PZT)/PZT sol-gel composite films were investigated to tailor their electrical properties. Three types of PZT powders were used to fabricate three different PZT/PZT sol-gel composite films. The PZT powders had the same electromechanical coupling coefficient but different relative dielectric constants. The PZT/PZT films were fabricated on a 3 mm-thick titanium substrate using an automatic spray coating system, and their properties were investigated. The relative dielectric constants of the PZT/PZT films were successfully controlled by tailoring the properties of the PZT powder phase. However, the piezoelectric constants showed a tendency different to those of the raw powders, because of the poor poling degree. This was overcome by conducting poling at a high temperature.

The hydrodynamic results obtained from the permeability of porous materials not only affect the assessment of the stream of the gas flow through those materials but they also refer to the loss of pressure energy in that flow. The direct measure of that loss is flow resistances.The results of experimental research upon the assessment of the flow resistances of porous materials with respect to gas flow. The research conducted applied to natural materials with an anisotropic gap-porous structure. The tests were carried out on a gas permeability measuring system, adapted to different shapes of porous material samples. The process issue of the total pressure drop on a porous deposit was considered in the Reynolds number category. The coefficient of flow resistance for anisotropic materials was defined and the value of this coefficient was compared to the gas stream and the total pressure drop on the porous bed was experimentally evaluated.

Growing concerns about the greenhouse effect, global warming, and adverse climate changes primarily stemming from carbon dioxide (CO2) emissions in traditional Portland cement (OPC) used in civil engineering construction, have prompted a shift toward eco-friendly alternatives like geopolymer cement (GPC). Over the last few decades, significant advancements have been made in developing environmentally sustainable pavement construction materials such as GPC to mitigate global CO2 emissions. The success of geopolymer cement (GPC) as an eco-friendly alternative to OPC has garnered attention for its potential to lower carbon emissions and enhance durability. This is attributed to the sustainable production method of GPC, where industrial cementitious waste materials (such as fly ash (FA), metakaolin (MK), mine tailings (MT), slag, etc.) are combined with an eco-friendly alkaline activator and water through the geopolymerization process. Numerous studies on geopolymer concrete indicate that, like OPC, GPC exhibits comparable mechanical properties, including strength, fire resistance, chemical resistance, and durability. This review explores the properties and applications of GPC as a sustainable material in pavement construction, exploring key studies and advancements in geopolymer technology, particularly its suitability for pavement applications. The assessment covers the mechanical properties, long-term performance, and environmental impact of geopolymer-based pavements, providing a comprehensive overview to inform policymakers, engineers, and researchers about the viability of geopolymer-based materials as a sustainable solution for modern pavement construction.

The main purpose of this study was to design a workplace in the conditions of a digital factory. The goal of this study is to compile a proposal for improving the layout solution in the selected enterprise to reduce material flows between individual workplaces. In addition, the workplace research study uses methods of material flow analysis with the application of visTABLE software support, which serves as a tool for designing production processes. The main result of the study was the reduction of the production time of the beam by 10 minutes and the creation of proposals for solutions for the company. The study helped with the visualization of processes within the digital factory to simplify and clarify processes at the workplace.

Iapetus, a Saturn moon, shows the most differentiated albedo dichotomy of the Solar System. The dark leading side has a lower albedo than the bright trailing side. Spectral data on the visible light reveal the existence of two types of materials on the surface. The darkening in the leading side is thought to be originated by the presence of organic material and carbonaceous compounds on surface, while the trailing side is covered by water ice due to migration processes from the dark side. On airless bodies like Iapetus, the surface escape speed is greater than the speed of water molecules, resulting in the retention of a H2O atmosphere that allows some species to get diffused through it. Here, there were performed simulations of the evolution of the surface temperature for each of the two hemispheres of Iapetus. The results showed a slow yet steady increment of temperatures for both sides, with a steeper slope for the dark hemisphere. It was also simulated how much energy budget can be accumulated in both sides and its consequences. Finally, we calculated the diffusion coefficients for ammonia, methane, and water ice. The results let us infer how these compounds could evolve over time.

The paper analyzes the phenomenon that condition the durability and reliability of a type of dental bur based on the wear of the active part and with effect on its quality. For the experimental study, a conical-cylindrical dental bur and a sample dental material in cobalt-chromium alloy, cylindrical shape, tested on a specially made experimental installation were used. The paper was limited to the consideration of a single parameter (loss of mass, mw by wear of the active part of the dental bur tested) for the establishment the durability and reliability, useful for the extension of the lifetime or even optimization of its operation. The wear phenomenon of the active part of dental bur is studied based on the results and experimental data obtained in the work process that was validated by interpolation and led to polynomial functions which approximate very well the dependent parameter, mw, considered in the experimental program. The results of the interpolation showed that in the first 11 h of work, the dental bur works with high efficiency, after which it can be easily decommissioned (optimizing operation, possibly constructive solutions); i.e., it should be replaced with a new one (criterion for replacing of worn dental bur).

Thermophysical characterization of three paraffin waxes (RT27, RT21 and RT35HC) is carried out in this study using DSC, TGA and transient plane source technics. Then, a numerical study of their melting in a rectangular enclosure is examined. The enthalpy-porosity approach is used to formulate this problem in order to understand the heat transfer mechanism during the melting process. The analysis of the solid-liquid interface shape, the temperature field shows that the conduction is the dominant heat transfer mode in the beginning of the melting process. It is followed by a transition regime and the natural convection becomes the dominant heat transfer mode. The effects of the Rayleigh number and the aspect ratio of the enclosure on the melting phenomenon are studied and it is found that the intensity of the natural convection increases as the Rayleigh number is higher and the aspect ratio is smaller. In the second part of the numerical study, a comparison of the performance of paraffins waxes during the melting process is conducted. Results reveals that from a kinetically RT21 is the most performant but in term of heat storage capacity, it was inferred that RT35HC is the most efficient PCM.

The present work sets out the evaluation of composite laminates through optimization objective functions. Genetic Algorithms (GA), as well as Simulated Annealing (SA), were performed in order to determine the optimal ply orientations of a fiber-reinforced polymer laminate for three given load cases: 1) in-plane loads, 2) combined moments, and 3) in-plane loads and combined moments. It searches the optimal orientation layup, which fulfills at the same time both the maximum strain criterion and the Tsai-Wu failure criterion. Construction of an objective function based on the strains and the stresses involves a minimization process to deformations and a maximization of the safety factor. For the first load case, the initial solution is [±45/0/90/±45]s, and the best solution is [(45/135)2/452]s. For the second load case, [-45/45/45/-45/0/90]s is the initial layup sequence, then the best solution obtained is [(45/-45)2/452]s, where plies at 0° and 90º are not necessary even when axial loads are applied. For the third study case, the original layup sequence is [0/45/-45/45/0/90]s; meanwhile, the best solution calculated is [21/24/145/140/45/49]s. An interesting observation is that each pair of layers has a 5º gap. The simulations show that the qualitative results from the GA are better than the SA, but with a significantly higher computational cost. These kinds of computational tools are expected to be used as a reference guide for an optimal fiber configuration with respect to the common orientations used when composite laminates are designed for a structural application.

In the last decade, the drone market has grown rapidly for both civil and military purposes. Due to their versatility, drones demand is constantly increasing, with several industrial players joining the venture to transfer urban mobility to the air. This has exacerbated the problem of noise pollution, mainly due to the relatively lower altitude of these vehicles and to the proximity of their routes to extremely densely populated areas. In particular, both the aerodynamic and aeroacoustic optimization of the propulsive system and of its interaction with the airframe are key aspects of the design of aerial vehicles for the success or the failure of their mission. The industrial challenge involves finding the best performance in terms of loading, efficiency and weight, and, at the same time, the most silent configuration. For this reason, research has focused on an initial localization of the noise sources and, on further analysis, of the noise generation mechanism, focusing particularly on directivity and scattering. The aim of the present study is to review the noise source mechanisms and the state-of-the-art technologies available in literature for its suppression, focusing especially on the fluid-dynamic aspects of low Reynolds numbers of the propulsive system and on the interaction of the propulsive-system flow with the airframe.

The recycling of wastes to obtain value-added products is a great challenge in the sustainable economy. In our studies, a mixed precursor containing aluminium scrap from end – of – life vehicles and TiO2 Degussa P25 was used to prepare TiO2 modified Al photocatalyst through solid state reaction. Al scrap and TiO2 Degussa P25 in the ration of n(Ti) / n(Al) = x (x = 0.0 - 2.5%), and acetylacetonate and Tween 80 was mixed under magnetic stirring and sintered using a con-ventional furnance at 550°C. DTA – TG – DTG, X – ray diffraction, Fourier – transform infrared, UV – Vis and photoluminescence spectroscopies were assed to investigate the thermal, structural, optical properties and photocatalytic activity. The effect of aluminium concentration on the characteristics of TiO2 Degussa P25 depending on the above instruments are studied. XRD revealed that the materials have crystal structure of anatase TiO2, rutile TiO2 and aluminium. The opto-electronic properties show that Al addition shifted the absorption spectra toward the visible range. The photocatalytic performance of Al – TiO2 composites was quantified by the degradation of Allura Red solution under a visible condition. The highest photocatalytic activity (79.99%) was achieved for the sample containing 0.5% Al and a higher concentration of Al particles shields the active centres of the semiconductor, thus reducing its photocatalytic activity. Aluminium scrap from end-of-life vehicles can be a source of raw material to be considered in semiconductor production. The spin-trapping technique evidenced that •O2- was the main species generated responsible for the Allura Red degradation.

Concrete is a heterogeneous material, one of the most widely used materials on the Planet and a major consumer of natural resources. Carbon emissions are largely due to the extensive use of cement in its composition, which contributes to 7% of global CO2 emissions. Extraction and processing of aggregates is another sources of CO2 emissions. Many countries have succeeded in moving from a linear economy to a circular economy by partially or fully replacing non-renewable natural materials with alternatives from waste recycling. One such alternative consists in partially replacing cement by supplementary cementitious materials (SCMs) in concrete mixes. Thus, the work is based on the experimental investigation of the fresh and hardened properties of civil engineering concrete, hereafter referred to as road concrete, in which, crushed river aggregate have been replaced with recycled waste aggregates of uncemented concrete and partial replacement of cement with a SCM material in the form of glass powder that improves the durability characteristics of this sustainable concrete. The microstructure and compositional features of the selected optimum composite has been also investigated by polarized light optical microscopy (OM) Scanning electron microscope (SEM) and X-ray diffraction by the Powder method (PXRD) for the qualitative analysis of crystalline constitutive materials.

In order to study the performance of a new type of cement-based grouting material under the coupling effect of freezing-thawing cycle and sulfate attack, experiments were designed and carried out. The damage mechanism of the material under the coupling effect of freezing-thawing and Na2SO4 solution was analyzed by measuring the mass change, relative dynamic elastic modulus, compressive strength loss and microstructure of the new grouting material. With increasing freeze-thaw cycles, mass loss and compres-sive strength loss of the sample in 15% Na2SO4 solution gradually increase, and the relative dynamic elastic modulus gradually decreases. During a 30-cycle freeze-thaw cycle, the mass loss rate, compressive strength loss rate, and relative dynamic elastic modulus of the sample are 4.17%, 24.59%, and 84.3%, respectively, showing good corrosion resistance and frost resistance durability. Microscopic analysis showed that SO42- caused the decomposition of C-S-H gel in the sample and the formation of Gypsum, and the widening of crack width aggravated the internal deterioration, indicating that the material deterioration rate increased under the dual-factor coupling effect.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

Carbonaceous material (CM) is common in meta-sediments and is generally interpreted to be intimately associated with gold mineralization. For the Bumo deposit in Hainan Province, South China, CM is mainly hosted by greenschist facies- to amphibolite-facies metamophic rocks of the Paleo- to Mesoproterozoic Baoban Group and by auriferous veins and is used as an important gold prospecting indicator. However, the genesis of CM and the relationship with gold mineralization are still not clear. Field work and thin section observation indicates that two types of CM occur, i.e., layered and veinlet. Layered CM, up to meters thick, prevails in the deposit. More importantly, Au-bearing sulfides are commonly distributed along the boundary between the quartz veins and layered CM. In contrast, veinlet CM, co-precipitated with gold and sulfides, has the thickness of micro- to centi- meters, and these thin veins occur in quartz veins and hydrothermally altered rocks. Scanning Electron Microscope (SEM) analysis indicates that layered CM has a stringy shape and laminate structure, while veinlet CM occurs as isometric particles. Raman carbonaceous material geothermometer indicates that layered CM with high maturity is formed at elevated temperatures of 400 – 550°C, consistent with X-ray diffraction (XRD) analysis. In contrast, veinlet CM with low maturity is formed at 200 – 350°C, generally consistent with gold mineralization. In addition, layered CM has δ13C values ranging from -30 to -20%, demonstrating a biogenic origin. Consequently, it is interpreted that layered CM is formed by a pre-ore metamorphic event during Caledonian, and its reducing nature promotes gold precipitation via destabilization of aqueous Au bisulfide complexes or facilitating sulfidation. Veinlet CM is hydrothermal origin, and its precipitation modified the chemical conditions of ore fluids, leading to the destabilization of Au complexes and thus favorable for mineralization.

The versatility of metal complexes of corroles raised the interest in the use of these molecules as element of chemical sensors. The tuning of the macrocycle properties by synthetic modification of the different components of the corrole ring, such as functional groups, molecular skeleton, and coordinated metal, allows the creation of a vast library of corrole-based sensors. However, the scarce conductivity of most of aggregates of corroles limits the development of simple conductometric sensors and requires the use of optical or mass transducers that are rather more cumbersome and less prone to be integrated in microelectronics systems. To compensate the scarce conductivity, corroles are often used to functionalize the surface of conductive materials such as graphene oxide, carbon nanotubes, or conductive polymers. Alternatively, they can be incorporated in heterojunction devices where they are interfaced with a conductive material such as a phthalocyanine. Herewith, we introduce two heterojunction sensors made of junctions of lutetium bisphthalocyanine (LuPc2) with either 5,10,15-tris(pentafluorophenyl) corrolato Cu (1) or 5,10,15-tris(4-methoxyphenyl)corrolato Cu (2). Optical spectra show that after forming the heterojunction, corroles maintain their original structure. The conductivity of the devices reveals an energy barrier for interfacial charge transport, which is larger in the 1/LuPc2 device. The different interfacial barriers is also manifested by the opposite response respect to ammonia: with a 1/LuPc2 behaving as a n-type conductor and 2/LuPC2 as a p-type conductor. Furthermore, the sensors show a high sensitivity respect to relative humidity with a reversible and fast response in the range 30-60%.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

We present organic, diamagnetic materials based on structurally simple (hetero-) tolane derivatives. They form crystalline thin-film aggregates that are suitable for Faraday rotation (FR) spectroscopy. The resulting new materials are characterized appropriately by common spectroscopic (NMR, UV-Vis), microscopy (POM), and XRD techniques. The spectroscopic studies give extremely high FR activities thus makes these materials promising candidates for future practical applications. Other than a proper explanation, we insist in the complexity of designing efficient FR materials starting off from single molecules.

3D-printing with foam concrete, which is known for its distinct physical and mechanical properties, has not yet been purposefully investigated. The article at hand presents a methodological approach for the mixture design of 3D-printable foam concretes and a systematic investigation of the potential application of this type of material in digital construction. Three different foam concrete compositions with water-to-binder ratios between 0.33 and 0.36 and having densities of 1100 to 1580 kg/m³ in the fresh state were produced with a pre-foaming technique using a protein-based foaming agent. Based on the fresh-state tests, including 3D-printing as such, an optimum composition was identified and its compressive and flexural strengths were characterised. The printable foam concrete showed compressive strength above 10 MPa and low thermal conductivity, which make it suitable for 3D-printing applications, while fulfilling both load-carrying and insulating functions.

In this study, to reduce the use of cement and sand, porous feldspar with excellent economic efficiency was used as a substitute in heat storage concrete layer. When cement was replaced with porous feldspar, the compressive strength was approximately 16%–63% higher compared with when cement was replaced with silicate minerals. To compensate for the reduction in strength owing to the decreased cement content, mechanical and chemical activation methods were employed. When the specific surface area of porous feldspar was increased, the unit weight was reduced by approximately 30% and the compressive strength was increased by up to 90%. When chemical activation was applied using a solidifying agent, the strength was increased by approximately 30% even though 70% of the cement content was replaced with porous feldspar. When cement and sand were replaced with porous feldspar, the compressive strength was approximately two times that of ordinary cement mortar. When the heat storage concrete layer material was replaced with porous feldspar in a pilot scale experiment, the thermal conductivity and heat storage characteristics were better than those of ordinary cement mortar, and an energy-saving effect of approximately 57% was observed, confirming the excellent applicability of porous feldspar as a building material.

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

. Manufacturers are increasingly adopting mixed-flow manufacturing models to meet the growing customized, diverse, and dynamic customer demand. In such an environment, material distribution scheduling optimization is vital for smooth operations and is integral to production management. However, manufacturers frequently encounter problems like disordered and delayed material distribution. Traditional scheduling methods suffer from problems like inadequate transparency, delayed decision directives, and suboptimal results, impacting performance. To this end, this study proposes a dynamic material distribution scheduling optimization model and strategy based on digital twin (DT) to address these problems. Firstly, we introduce workstation satisfaction and establish a material distribution path optimization model minimizing total distribution cost while maximizing workstation satisfaction. Subsequently, we present a cloud-edge computing-based decision framework and explain the DT-based material distribution system's components and operation. Furthermore, a dynamic material distribution scheduling optimization mechanism based on DT is designed. By incorporating a savings method and incentive, penalty strategies, improvements are made to the path node selection probabilities and the information pheromone update rules of the traditional ant colony optimization (ACO) algorithm. Finally, a numerical case study, using real data from collaborating enterprises, validates the proposed algorithm and strategy. This research offers valuable insights into logistics management and algorithm design in smart manufacturing environments.

Background: Producing, distributing or discussing child sexual abuse materials (CSAM) is often committed through the dark web in order to remain hidden from search engines and regular users. Additionally, on the dark web, the CSAM creators employ various techniques to avoid detection and conceal their activities. The large volume of CSAM on the dark web presents a global social problem and poses a significant challenge for helplines, hotlines and law enforcement agencies. Objective: Identifying CSAM discussions on the dark web and uncovering associated metadata insights into characteristics, behaviours and motivation of CSAM creators. Participants and Setting: We have conducted an analysis of more than 353,000 posts generated by 35,400 distinct users and written in 118 different languages across eight dark web forums in 2022. Out of these, approximately 221,000 posts were written in English and contributed by around 29,500 unique users. Method: We propose a CSAM detection intelligence system. The system uses a manually labelled dataset to train, evaluate and select an efficient CSAM classification model. Once we identify CSAM creators and victims through CSAM posts on the dark web, we proceed to analyze, visualize and uncover information concerning the behaviors of CSAM creators and victims. Result: The CSAM classifier, based on Support Vector Machine model, exhibited good performance, achieving the highest precision of 92.3\%, accuracy of 87.6\% and recall of 84.2\%. Its prediction time is fast, taking only 0.3 milliseconds to process a single post on our laptop. While, the Naive Bayes combination is the best in term of recall, achieving 89\%, and its prediction time is just 0.1 microseconds per post. Across the eight forums in 2022, our Support Vector Machine model detected around 63,000 English CSAM posts and identified near 10,500 English CSAM creators. The analysis of metadata of CSAM posts revealed meaningful information about CSAM creators and their victims, such as: (1) the ages and nationalities of the victims typically mentioned by CSAM creators, (2) forum topics where the CSAM creators assign their posts, and (3) online platforms preferred by CSAM creators for sharing or uploading CSAM. Conclusion: Our CSAM detection system exhibits high performance in precision, recall, and accuracy in real-time when classifying CSAM and non-CSAM posts. Additionally, it can extract and visualize valuable and unique insights about CSAM creators and victims by employing advanced statistical methods. These insights prove beneficial to our partners, i.e. national hotlines and child agencies.

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Self-compacting concrete (SCC) is a high-quality construction solution combining high fluidity, passing and filling ability with improved mechanical properties and durability. In the present study, the effect of incorporating alternative waste materials, such as two by-products of the ce-ment industry, namely cement kiln dust (CKD) and by-pass dust (BPD), into SCC as partial re-placement for traditional filler material was investigated. The produced compositions were compared with reference mixtures containing only marble powder (MP) as a filler. A series of tests including specific test methods for wet SCC, compressive, flexural and tensile splitting strength tests as well as drying shrinkage determination were conducted to evaluate the quality of the produced SCC in terms of fresh and hardened SCC properties. The use of alternative fine filler materials resulted in a high-performance sustainable SCC of low cement content. Specifi-cally, incorporating CKD into the SCC enhanced its rheological behavior and improved slightly its mechanical properties, while the use of BPD led to SCC mixtures of adequate rheological characteristics but with highly upgraded mechanical and physical properties

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

Greenhouse gas (GHG) emissions from human activities have climbed significantly above pre-pandemic levels and reached record highs that unequivocally accelerate global warming. Industry has a significant impact on climate change, emitting at least 21 % of global GHGs and making little overall progress toward its reduction until now. Reducing industry’s emissions requires coordinated action along the value chains in order to promote mitigation options, such as energy and material efficiency, circular material flows, and transformative changes within production processes. The authors analyzed the GHG emissions generated during the manufacturing of three different products of automotive suppliers located in Austria. Despite previous efforts toward an environmentally compatible fabrication, additional and significant reduction potentials were identified. These measures for product carbon footprint (PCF) reduction included the sourcing of low-carbon materials (which are already available on the market), more extensive use of renewable energy, and changes towards more resource efficient manufacturing processes and machinery. Depending on the materials used, the PCF can be reduced by up to 80 %. The findings serve to prepare for future PCF reporting regulations and illustrate reduction potentials to achieve future market advantages, especially when PCFs become an awarding criterion.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

In Ecuador, particularly in the El Oro province, gold mining has been historically hampered by arsenic contamination in the ores. This research addresses the persistent issue of arsenic in gold-bearing ores from Miraflores Mine in Cerro Azul, Atahualpa Canton, and the challenges it presents to mining operations. The study's purpose is to evaluate the effectiveness of an alkaline leaching process for arsenic removal. The ore underwent thorough characterisation, employing advanced techniques like fire assay and atomic absorption. Once the ore's nature was discerned, an arsenic extraction experiment using a leaching solution was conducted. The implemented process achieved an arsenic removal efficiency of 90.54%. This enhanced ore quality facilitates efficient metallurgical applications and, more notably, reduces the environmental footprint by diminishing the need for harmful reagents like sodium cyanide. However, a significant implication of this method is the added cost due to the need for heat during the leaching test, amounting to an approximate $30 per ton increase. The alkaline leaching process emerges as a promising solution for arsenic challenges in El Oro’s mining sector. While the findings are encouraging, further expansive tests are recommended to validate the results and underscore the urgency for sustainable and hazard-conscious mining practices.

Solar concentration is the ability to harness solar radiation to increase the temperature of a receiver. The receiver is the component into which a heat transfer fluid can be flowed for an ORC system and produce electricity, or it can be used for high-temperature thermal storage, or even to implement thermochemical cycles. The choice of material is critical to ensure optimal performance and long-lasting operation. It is also essential that such material can operate at high temperatures and high thermal gradients. In short, material identification involves high thermal stresses that result in structural deformation. Different metal alloys were used to verify that the yield strength limit was not exceeded due to thermal stress induced by concentrated solar radiation. The problem was implemented in Matlab starting from the general heat equation. The purpose is to test whether thermal stress exceeds the yield strength, which is the condition in which elastic bonds in the material are changed, causing deformation. The best material identified was Inconel 740H, which had a high yield strength value and the lowest temperature difference. Under extreme working conditions, it can withstand thermally induced shocks.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

The contribution deals with the joining of various types of materials by technology of thermal drilling. In various branches of industries, also in the automotive industry must be joining operations, service, repairing, substitution or protection workpieces, components with various types of materials. Equally, the important role as joint, is also used material, and a product preparation by assembly and disassembly operations. By utilization of new friction hybrid joining technologies we can shortage the production time, provide automation in operations, increase the quality of joints, spare of economical expenses and also we can protect the environment. In this paper authors have investigated the effect of friction drilling on the tested material, aluminium alloy AlMgSi, which was used for material testing. The created joints were evaluated visually and by microscopy methods. The errors of tested joining were documented and described, too. This contribution was made with cooperation of Technical University of Kosice and with U. S. Steel Kosice, s.r.o.

There are some controversies about 2G bioethanol and it is in need of a reliable test data in order to make a further analysis and proof. In collecting basic data from three classes of typical raw materials, such as wheat, maize stalk juice, and straw, it was found that 4.32 tons straw or 3.358 tons wheat is needed to produce 1-ton bioethanol. Using the coefficient of variation calculation and analysis method, it is able to obtain the C.V. value of straw fermentation efficiency 0.08932<0.15, indicating the fermentation technology and process of 2G bioethanol is already quite mature and reliable, without risk, and also with a raw material cost advantage. There is a problem in that the C.V. value of straw volume is 1.2648>0.95, indicating 2G bioethanol is in an extremely high-risk area. Using the straw volume calculation method, building and its costs – capital expenditure of 2G bioethanol plant is approximately seven times that of a wheat ethanol plant. This should be some of the important reasons why it is noncompetitive, extremely high price, and requiring government subsidies. Straw volume data study has caused the 2G bioethanol plant to require more cement, steel, equipment, and other materials. Thus, there are ample reasons to question the CO2 emissions and its carbon footprint of 2G bioethanol plant. Actually, the volume is not the only existing problem, it is necessary to re-evaluate and discuss the definition of 2G bioethanol and its future.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging material seem to be promising due to their low weight, structure and production price. Based on the review, the linear low-density polyethylene material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a Constitutive material model to be used in future design by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of the linear low-density polyethylene under static and dynamic loading. The quasi-static measurement is realized in two perpendicular principal directions and is supplemented by a test measurement in the 45 degrees direction, i.e. exactly between the principal directions. The quasi-static stress-strain curves are analyzed as an initial step for dynamic strain rate dependent material behavior. The dynamic response is tested in the drop tower using a spherical impactor hitting the flat material multi-layered specimen at two different energy levels. The strain rate dependent material model is identified by optimizing the static material response obtained in the dynamic experiments. The material model is validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

Background: The saga of repatriating cultural artefacts continues as western museums face increasing pressure from claimants. Western museums that have been involved in the display of historical artefacts, most of which were acquired during the colonial period, have come under huge criticism. A heated discussion of late has been the legitimacy of retaining artefacts in western museums. This study aimed at investigating the ongoing debate regarding the restitution of artefacts. Objective: To investigate the arguments for and against the repatriation of artefacts in relation to diplomatic exchange, preservation, legitimacy and usefulness. Methods: Records will be searched in electronic databases including the University of Manchester Library for Social Anthropology, Scorpus and Project MUSE. Search terms will include "return of artefacts", “return of historical objects”, “return of cultural objects”, “western museums”, “restitution of artefacts”, “repatriation of artefacts”, “restitution of historical objects”, repatriation of historical objects”, “restitution of cultural objects”, “repatriation of cultural objects”, "material culture", "return of antiquities”, restitution of antiquities” and “repatriation of antiquities”. Coding and analysis will be done in SWIFT-Review. The deductive and inductive approaches will be used in synthesising results. Both tabular and graphical methods will be used to present results. Ethics and Results: This study did not need any ethical approval. Results on study characteristics, quality and risk of bias assessments as well as the synthesis of arguments for and against the restitution of artefacts will be presented. The review results will be reported according to appropriate guidelines and disseminated through publication in a relevant journal and presented to stakeholders where necessary. Conclusions: This review will be based on current protocols for systematic review and qualitative evidence synthesis. The study will be the first review that seeks to pull together claims for and against the return of cultural artefacts. The conclusions that will be drawn and recommendations will provide the basis for further research into the debate and the way forward. This study will also help identify the existing gaps regarding the subject matter.

This paper presents a new method to model the nonlinear behaviour of masonry double curvature structures, possibly reinforced by composite materials, by means of conventional elasto-plastic analyses. It is meant to be used in professional design, especially for assessment and retrofitting purposes, therefore based on the exploitation of the simplest nonlinear Finite Elements available in a commercial software, namely trusses with elasto-fragile and elasto-ductile behaviour (Cutoff Bars). The numerical static nonlinear analyses are carried out by considering elastic hexahedral elements for bricks and lumping nonlinearities on joints. These have been assumed in turn elastic-brittle and elastic-plastic by using 1D elements, respectively Point Contacts, under No-Tension Material hypothesis, and Cutoff Bars, assigning small tensile resistance to the material. The reinforcement, realised with FRP hooping strips, has been successfully modelled in a similar fashion, i.e. by applying perfectly bonded elastic-plastic Cutoff Bars at the extrados of the dome, where the debonding is accounted for in a conventional way limiting the tensile strength according to Italian Standards indications. The procedure is validated against benchmark models with the same geometry, using experimental data and more refined structural model results for comparison.

This research investigates the socio-economic impact of rattan cane processing on the livelihoods of practitioners in Ibadan Metropolis. It comprehensively assesses raw material availability, examines factors influencing demand and supply, and evaluates sales to determine the profitability of rattan processors. With the snowball and total enumeration sampling methods, the study engages with a diverse group of rattan processors. The study reveals a concerning 36% acknowledgement of a decline in the availability of canes attributed to deforestation and over-exploitation. Notably, it emphasizes that rattan product manufacturing in Ibadan Metropolis operates at a craft level, employing tools like saws, hammers, knives, gas cylinders, pinches, and tape rules, impacting production efficiency and product longevity. Additionally, the research underscores the absence of government support and credit facilities reported by all respondents. The Market Margin analysis highlights varying profitability levels across rattan products, with chairs exhibiting notably higher profitability (32.22%) than others. Individual profit margins for specific products, such as chairs (145.00%), underscore the significance of processing costs, production time, and market demand. The study offers strategic recommendations, advocating for district-level service centres for training, technology transfer, and support to enhance skills and technical efficiency. It calls for government intervention through incentives, facilities, tax breaks, and policies to fortify the rattan trade, improving production standards and unlocking export market potential. Furthermore, financial support, technical assistance, and mechanization should be employed to reduce production costs and time, ultimately elevating income generation in the rattan industry. This research contributes valuable insights to the discourse on sustainable livelihoods and economic viability within the rattan sector.

Material Extrusion is a popular additive manufacturing technology due to its low cost, wide market availability, ability to construct complex parts, safety, and cleanliness. However, optimizing the process parameters to obtain the best possible mechanical properties has not been extensively studied. This paper aims to develop ensemble learning-based models to predict the ultimate tensile strength, Young's modulus, and strain at break of PLA and PLA-CF 3D-printed parts, using printing temperature, printing speed, and layer thickness as process parameters. Additionally, the study investigates the impact of process parameters and material selection on the mechanical properties of the printed parts and uses Genetic Algorithms for multi-objective optimization according to user specifications. The results indicate that process parameters and material selection significantly influence the mechanical properties of the printed parts. The Genetic Algorithm successfully identifies optimal parameter values for the desired mechanical properties. Moreover, this work is the first to model Process-Structure-Properties relationships for an additive manufacturing process and to use a multi-objective optimization approach for multiple mechanical properties, utilizing ensemble learning-based algorithms and Genetic Algorithms.

The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

Taking advantage of fact that the surface electrons of metallic nanoparticles (NPs) can be effectively released even at a low voltage bias, we demonstrate an improvement in the electrochemical performance of nano-sized Prussian Blue (PB) based secondary batteries by the incorporation of bare Ag or Ni NPs onto the vicinity of the working PB NPs. It is found that the capacity for electrochemical energy storage of the 17-nm-PB-based battery is significantly higher than the capacity of 10-nm-PB-based, 35-nm-PB-based or 46-nm-PB-based batteries. There is a critical PB size for the highest electrochemical energy storage efficiency. The full specific capacity CF of the 17-nm-PB-based battery stabilized to 62 mAh/g after 130 charge-discharge cycles at a working current of IW = 0.03 mA. The addition of 14 mass-percent of Ag NPs in the vicinity of the PB NPs gives rise to a 32% increase in the stabilized CF. A 42% increase in the stabilized CF can be obtained with the addition of 14 mass-percent of Ag NPs on the working electrode of the 35-nm-PB-based battery. An enhancement of CF is also found for electrodes incorporating bare Ni NPs but the effect is smaller.

The plant-microbe-soil nexus is critical in maintaining biogeochemical balance of the biosphere. However, soil loss and land degradation are occurring at alarmingly high rates, with soil loss exceeding soil formation rates. This necessitates evaluating marginal soils for their capacity to support and sustain plant growth. In a greenhouse study, we evaluated the capacity of marginal incipient basaltic parent material to support native plant growth, and the associated variation in soil microbial community dynamics. Three plant species, native to the Southwestern Arizona-Sonora region were tested with three soil treatments including basaltic parent material, parent material amended with 20% compost, and potting soil. The parent material with and without compost supported germination and growth of all the plant species, though germination was lower than the potting soil. A 16S rRNA amplicon sequencing approach showed Proteobacteria to be the most abundant phyla in both parent material and potting soil, followed by Actinobacteria. Microbial community composition had strong correlations with soil characteristics but not plant attributes within a given soil material. Predictive functional potential capacity of the communities revealed chemoheterotrophy as the most abundant metabolism within the parent material, while photoheterotrophy and anoxygenic photoautotrophy were prevalent in the potting soil. These results show that marginal incipient basaltic soil has the ability to support native plant species growth, and non-linear associations may exist between plant-marginal soil-microbial interactions.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

Additive manufacturing has already been established as a highly versatile manufacturing technique with demonstrated potential to completely transform conventional manufacturing in the future. The objective of this paper is to review the latest progress and challenges associated with the fabrication of multi-material parts using additive manufacturing technologies. Various manufacturing processes and materials used to produce functional components were investigated and summarized. The latest applications of multi-material additive manufacturing (MMAM) in automotive, aerospace, biomedical and dentistry field were demonstrated. Investigation on the current challenges were also carried out to predict the future direction of MMAM processes. It is concluded that the further research and development needed in the design of multi-material interfaces, manufacturing processes and material compatibility of MMAM parts are necessary.

The analysis of curated genomic, metagenomic, and proteomic data are of paramount importance in the fields of biology, medicine, education, and bioinformatics. Although this type of data is usually hosted in raw form in free international repositories, its access requires plenty of computing, storage, and processing capacities for the domestic user. The purpose of the study is to offer a comprehensive set of genomic and proteomic reference data, in an accessible and easy-to-use form to the scientific community. A representative type material set of genomes, proteomes and metagenomes were directly downloaded from the site: https://www.ncbi.nlm.nih.gov/assembly/ and from Genome Taxonomy Database, associated with the major groups of Bacteria, Archaea, Virus, and Fungi. Sketched databases were subsequently created and stored on handy raw reduced representations, by using Mash software. Our dataset contains near to 100 GB of space disk reduced to 585.78 MB and represents 87,476 genomics/proteomic records from eight informative contexts, which have been prefiltered to make them accessible, usable, and user-friendly with computational resources. Potential uses of this dataset include but are not limited to, microbial species delimitation, estimation of genomic distances, genomic novelties, paired comparisons between proteomes, genomes, and metagenomes.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.

Non-pneumatic tires have gained a lot of attention due to their advantages, including not having to worry about getting a flat tire. In this type of tire, metamaterial cells replace the pneumatic part of the tire. In general, metamaterials are formed by stacking cells together. These cells are obtained by various methods including topology optimization. Therefore, in this research, to achieve a metamaterial cell suitable for a non-pneumatic tire with the objective function of increasing compressive strength and bending fatigue life, optimization for three types of geometry including (1) square plane, (2) rectangular plane, and (3) entire circumference of tire and three types of material including polylactic acid (PLA), thermoplastic polyurethane (TPU) and void have been done. Optimization has been implemented by using MATLAB code in 2D mode. The cubic cell is obtained from extruding the optimized response of the square plane. From the optimized response of the rectangular plane, the cylindrical cell and from extruding the optimized response of the entire circumference of tire to the tire cross-section size, the main geometry of the tire has been calculated. Finally, to check the quality of 3D printing in producing cells and how they are connected, the optimal cell fabricated by the fused deposition modeling (FDM) method has been observed using a field-emission scanning electron microscopy (FE-SEM). The results show that in the optimization of the square plane, the sample with the minimum remaining weight constraint equal to 40% and in the optimization of the rectangular plane and the entire circumference of tire, the sample with the minimum remaining weight constraint equal to 60% was selected as the optimal sample. From checking the quality of 3D printing, it has been concluded that PLA and TPU materials are completely connected.

Criticism has been directed towards the traditional methods of management accounting employed by organizations thus far, as they fail to adequately address the growing need for competitiveness and sustainable development in a globalized environment. This criticism stems from both economic factors, such as insufficient monitoring of material, energy, and escalating overhead costs, and environmental concerns, where inadequate attention is given to vital information regarding significant environmental aspects, impacts, risks, and damages arising from the organization's activities and processes. Additionally, these methods do not sufficiently support the implementation of a functional environmental management system (EMS). Drawing upon our research in EMS standardization following the international standards ISO 1400X, as well as our knowledge gained during the development of the Slovak Technical Standard (STN) for ISO 14051, this paper presents an innovative model of environmental management accounting. This model is based on the cost accounting of material and energy flows within organizations. It serves as an enhancement framework for organizations with an existing EMS built according to the EN ISO 14001 model, as well as for organizations lacking a formalized EMS based on this standard. Within this paper, we specify, decompose, and apply the new model, focusing on the cost accounting of material-energy flows in a hypothetical organization. We meticulously examine the ten key steps of the model's structure, particularly in terms of costing and the allocation of costs to material, energy, system, and waste management.

Artificial reefs have been deployed in multiple regions of the world for different purposes including habitat restoration and protection, biodiversity and fish stock enhancement, fisheries management and recreation. Artificial reefs can be a valuable tool for ecosystem protection and rehabilitation, helping mitigate the effects of anthropogenic impacts that we face today. However, knowledge on artificial reefs is unevenly distributed worldwide, with some regions having much more quality information available and published (e.g. European Mediterranean Sea area), while others, for instance the North-East Atlantic area, do not. Here, we provide a characterization of purposely built artificial reefs in North-East Atlantic area based on all available literature (i.e. research papers and reports), highlighting the needs and gaps that are vital for establishing future perspectives for artificial reef deployment and research. In the North-East Atlantic area, sixty-one purposely built artificial reefs have been deployed since 1970, mostly between the years 1990-2009, with Spain being the country with the highest number of artificial reefs. The most reported purpose for their deployment is fisheries productivity and habitat/species protection, although, most artificial reefs are multipurpose in order to maximise the benefits of a given financial investment. The majority of artificial reefs were submerged at < 50 m, mainly between 10-20 m of depth. The most used designs were cubic blocks and complex designs made by an array of combined shapes, which mostly consist of concrete (79%). From all the analysed data on artificial reefs, 67% of the cases reported surveys to assess biodiversity after the deployment. However, in 26% of those cases, data was not available. When data was available, only 31% of cases reported long-term biomonitoring surveys (3 years or more). Based upon these findings, we noticed a general lack of scientifically robust data, including records of species and abundance of both fish and invertebrates, as well as macroalgae. Preventing an adequate determination of the best balance between shape, construction material and bio-colonization. Critiques and suggestions are discussed in the light of current available data in order to perform more efficient research, evaluation and functioning of future artificial reefs.

The present work shows a novel physical-mathematical model to estimate the average corrosion resistance index from the crystallographic texture in API 5L steels. The crystallographic texture of the studied steels was measured by means of the X-ray diffraction technique. The model, based on the symmetric spherical surface harmonics for a BCC structure, is capable of describing the anisotropy surface of anodic dissolution resistance of the crystal and establishing a straightforward relationship between crystallographic texture, surface roughness, and metal corrosion behavior. The predictions of the average corrosion resistance index made from the crystallographic texture were in good agreement with those obtained from potentiodynamic polarization curves for the investigated steels. This agreement validates the capacity of this model and opens the possibility of applying it as a novel criterion for the material selection and design stages in order to combat metal corrosion problems.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

The global predicament of solid waste generation looms as a mounting crisis, profoundly impacting the world, particularly in developing nations. Each day, the world's population contributes millions of tonnes of municipal solid waste, with projections pointing toward further escalation in the coming years. This surge in waste, predominantly composed of cellulose-rich materials, correlates directly with heightened pollution, a threat that transcends borders and imperils humanity as a whole.To confront this ever-growing issue, cellulase, a potent hydrolytic enzyme capable of digesting cellulose, a chief component of solid waste, is explored as a potential solution. In this study, we harness cellulase enzymes derived from the digestive tracts of both Archachatina marginata and Oryctes rhinoceros larvae, employing them as biodegradation agents for cellulose-based waste materials.The cellulase enzymes are methodically isolated and partially purified via ammonium sulfate precipitation at 65% saturation. Their efficacy in breaking down a variety of waste categories, encompassing kitchen waste, leaves, paper, wood, and industrial waste, is meticulously assessed and benchmarked against carboxymethyl cellulose (CMC), a well-established laboratory substrate. The study also ascertains the specific activity of these enzymes.Spectrophotometric analyses of the cellulase enzymes' actions on the diverse waste materials unveil intriguing results. Archachatina marginata and Oryctes rhinoceros larvae exhibit distinct performance metrics, registering percentage ranges of (11.04% - 28.31%) and (33.69% - 189.11%) on wood waste, (76.52% - 196%) and (108.56% - 567.01%) on paper waste, (78.57% - 148.14%) and (163.33% - 436.76%) on leaf waste, (57.16% - 179.95%) and (63.38% - 457.05%) on kitchen waste, and (59.95% - 77.51%) and (117.26% - 155.23%) on industrial waste, respectively. This study underscores the substantial biodegradation potential inherent in cellulase enzymes from both Oryctes rhinoceros larvae and Archachatina marginata when applied to diverse waste materials. While the rates and impacts of waste degradation vary between these sources, their promising contributions to waste management come into focus, offering sustainable and innovative approaches to tackle the pressing global challenge of solid waste proliferation.