Lead Acid Batteries (LABs) are used for starting, lighting, and igniting, as well as in air conditioning systems and to supply power to electric engines in transport vehicles (TVs). However, the application of LABs for TVs has faced a number of market challenges, mounted by the upcoming high energy density and long lifespan batteries, such as lithium ion. LABs, on the other hand, are inexpensive. The key research question is, how can the lifespan of LABs used in automotive industries be increased, while still ensuring a low cost solution? Thus, integrating LABs with the supercapacitor (known as an electric double layer capacitor—EDLC) is likely to outperform the competing alternative batteries for TVs. This paper proposes a multiple stage approach to hybrid lead acid batteries and a supercapacitor system for TVs that is capable of maintaining the battery state-of-charge (SOC) at statistically high limits, ranging between 90% and 95%. This SOC target will likely ensure that the lifespan of the hybrid battery system can be elongated (extended) more than its competitors. In this study, the multiple stage approach of concatenated converters has been designed in order to satisfy all energy storage requirements for different characteristics of LABs and the supercapacitor. The designed hybrid system has been simulated using Matrix Laboratory (MATLAB/Simulink (version R2016a, MathWorks, Natick, MA, USA)). The simulated results show that high transient currents from the direct current (DC) bus of LABs, caused by the regenerative braking or deceleration of the TVs, reduce the battery lifespan and induce mechanical stress. The supercapacitor reduces the stress on the LAB by absorbing high transient currents. This, in turn, keeps the LABs’ SOC between 90% and 96% and the voltage at 12 V. As indicated by the simulated results, the hybrid battery SOC is maintained at 90–96% and the terminal voltage is approximately 12 V.

Accurate and efficient battery modeling is essential to maximize the performance of isolated energy systems and to extend battery lifetime. This paper proposes a battery model that represents the charging and discharging process of a lead-acid battery bank. This model is validated over real measures taken from a battery bank installed in a research center placed at “El Chocó”, Colombia. In order to fit the model, three optimization algorithms (Particle Swarm Optimization, Cuckoo Search, and Particle Swarm Optimization+Perturbation) are implemented and compared, being the last one a new proposal. This research shows that the model with the proposed algorithm is able to estimate and manage the real battery characteristics as SOC and charging/discharging voltage. The comparison between simulations and real measures shows that the model is able to absorb reading problems, signal delays, and scaling errors. The approach we present can be implemented in other types of batteries especially those used in stand-alone systems.

Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

Four naturally occurring zeolites AZLB-Ca and AZLB-Na (Bowie, Arizona), NM-Ca (Winston, New Mexico), and NV-Na (Ash Meadows, Nevada) were studied to evaluate structural modifications after treatment with HCl acid. AZLB-Ca and AZLB-Na are chabazite-like species and become amorphous when boiled in concentrated HCl acid as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na which are clinoptilolite-like species withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca (20.0(1) to 111(4) m2/g) and NV-Na (19.0(4) to 158(7) m2/g). 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native (NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g) compared to the modified zeolites (30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g) and also decreased upon K+ ion pretreatment in the HCl modified zeolites.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

Rapid industrialization, urbanization, and population explosion in sub-Saharan Africa escalate environmental Lead levels with subsequent elevation of blood Lead levels in children. Nutrition status, age, and genetics govern one’s susceptibility to Lead toxicity. This study expounded this susceptibility by relating blood Lead levels, d-aminolevulinic acid dehydratase enzyme activity (ALAD), and genetic variations of proteins that code for ALAD enzyme in urban children of Uganda. Spectrophotometric analysis for blood Lead (BL), hemoglobin levels, and determination d-levels aminolevulinic acid dehydratase enzyme activity of the blood samples from 198 children were performed prior to a polymerase chain reaction and restriction fragment length digestion for ALAD polymorphism was done. Up to 99.5% of samples coded for the ALAD1 allele whereas 0.05% coded for ALAD2. Genotypes ALAD2-2 members had elevated BLL (mean 14.1 µg/dL) and reduced ALAD enzyme activity compared to others. This, therefore, implies that the majority of children hoard BL which may affect them later in life.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

Hazardous toxic metals, such as lead and cadmium, and to a lesser extent aluminum, are extensively recognized as detrimental for health following ingestion within food and water, or following inhalation. Gut and food-derived microbes, by interacting with heavy metals, may actively or passively modulate their bioavailability inside the gut, either by adsorption or by sequestration. Such a bioremediation within the gut implies the selection of safe microbes, based on their specific capacities to immobilize metals. We investigated the metal removal ability of 225 bacteria toward the potential harmful trace elements lead, cadmium and aluminum in vitro, using Inductively Coupled Plasma Mass Spectrometry analysis. Interspecies and intraspecies comparisons were addressed and discussed among bacteria from the phylum Firmicutes, which are mostly lactic acid bacteria, including Lactobacillus spp, with some Lactococcus, Pediococcus and Carnobacterium representatives, Actinobacteria as well as Proteobacteria. The effect on mixture of lead and cadmium was also investigated. Although the purpose of such a screening is so far not to elucidate each of the various strain specific- and metal dependent- mechanisms of heavy metal removal, we identified potential bacteria which are able to alleviate Pb(II) and Cd(II) concerns in order to propose performing candidate probiotics for metal xenobiotic bioremediation.

Manganese sludge, an industrial waste in the ferroalloy industry, contains various components and holds significant importance for sustainable development through its valorization. This study focuses on characterizing a manganese sludge and investigating its behavior during sulfuric acid leaching. The influence of process conditions, including temperature, acid concentration, liquid to solid ratio, and leaching duration, was examined. The results revealed that Mn, Zn, and K are the main leachable components, and their leaching rates increase with increasing temperature, liquid to solid ratio, and time. However, acid concentration requires optimization. High leaching rates of 90% for Mn, 90% for Zn, and 100% for K were achieved. Moreover, it was found that Pb in the sludge is converted to sulfate during the leaching which yields a sulfate concentrate rich in PbSO4. The leaching process for Mn and Zn species appears to follow a second or -third order reaction, and the calculation of rate constants indicated that Mn leaching kinetics are two to five times higher than those for Zn. Thermodynamic calculations were employed to evaluate the main chemical reactions occurring during leaching.

Biofilms are communities of microorganisms that can colonize biotic and abiotic surfaces playing a significant role in the persistence of bacterial infection and antibiotic resistance. About 65% and 80% of microbial and chronic infections are produced by biofilm formation. The increase in infections by multi-resistant bacteria draws attention to the discovery of new drugs based on natural inhibitory molecules. The inhibition of diguanylate cyclases (DGCs), the enzyme implicated in the synthesis of the second messenger, cyclic diguanylate (c-di-GMP), involved the biofilm formation, represents a potential method for preventing the biofilm development. It has been extensively studied using PleD protein as a model of DGC for in silico studies as virtual screening and as a model for in vitro studies in biofilms formation. In the present study 224205 molecules from natural products database, ZINC15 has been evaluated through molecular docking and molecular dynamic simulation, our result suggests trans-Aconitic acid (TAA) as a possible starting point for hit-to-lead methodologies to obtain new molecules capable of inhibiting the PleD protein and hence blocking the biofilm formation.

For the eutectic molten PbBi alloy, we tested the additive properties of density, sound velocity, compressibility and dynamic viscosity of this alloy in the temperature range 600 – 1200 K. All these values can be represented as a mass-weighted sum of the corresponding values of pure lead and bismuth in the temperature range 600 – 1000 K within the limit of experimental errors. In the temperature range 800 – 900 K, we found that interatomic forces in the eutectic increase with temperature, which is caused by a decrease in the size of accumulations of atoms, clusters, of melt. A decrease in the size of clusters is accompanied by an increase in bonds between atoms within the clusters, which make them more stable.

Objective: To determine blood lead levels (BLL) in a healthy paediatric population and to analyse related sociodemographic, dietary and haematological factors. Methods: A cross-sectional study was made of 1,427 healthy subjects aged 1-16 years from the city of Almería (south-eastern Spain). BLL, iron parameters and erythropoietin were determined, and sociodemographic and dietary data obtained. The study data were analysed by multiple logistic regression. Results: The mean BLL was 1.98±1.1 µg/dl (95% CI:1.91–2.04). For 5.7% of the population, mean BLL was 2-5 µg/dl, for 2.1% it was >5 µg/dl and for 0.15% it was >10 µg/dl. Multivariate analysis showed that immigrant origin (OR:11.9; p<0.0001), low level of parental education (OR:4.6; p<0.02) and low dietary iron bioavailability (OR: 3.2; p<0.02) were all risk factors for toxic BLL. Subjects with toxic and non-toxic BLL presented similar iron and erythropoiesis-related parameters, except erythrocyte protoporphyrin, which was significantly higher in the BLL >5 µg/dl group. Conclusions: BLL and the prevalence of toxic BLL in healthy subjects aged 1-16 years living in south-eastern Spain are low and similar to those found in other developed countries. The factors associated with toxic BLL are immigrant origin, low level of parental education and dietary iron deficiency. The toxicity of BLL was not related to changes in the analytical parameters studied.

Flushing tap water is often promoted as a simple and low cost approach to reducing water lead exposures. This study evaluated lead reduction when prevailing flush guidelines (30 seconds-2 minutes) are implemented in a city compliant with lead-associated water regulations (New Orleans, LA). Water samples (n=1,497) collected from a convenience sample of 376 residential sites (2015-2017) were analyzed for lead in samples collected: at 1) first draw (n=375), and after incremental flushes of 2) 30-45 seconds (n=375), 3) 2.5-3 minutes (n=373), and 4) 5.5-6 minutes (n=218). There was no significant reduction when compared to the first draw lead level, until the 6 minute flush (p<0.05); but most sites (52%) still had detectable lead (≥1 ppb) after 6 minutes. Older homes (pre-1950) and low occupancy sites had significantly higher WLLs (p<0.05).Each sample type had health-based standard exceedances at over 50% of sites sampled (max: 58 ppb). While flushing is an effective short-term approach to remediate high lead, prevailing flush recommendations are an inconsistently effective exposure prevention measure that can often inadvertently increase exposures. Public health messages should be modified to ensure appropriate application of flushing for specific cities, while acknowledging its short-comings and practical limitations.

The research was conducted in the Kırklareli stream, which flows southwest through the city of the same name toward the village of Kavaklı. The aim of the study is to evaluate water analysis results and assess the potential that the European Union drinking water standard for lead can be achieved in the Kırklareli stream by reliance on the low solubility of lead phosphate minerals. The present study used Visual MINTEQ 3.1 for all water chemistry simulations. The European Union drinking water standard for lead, which is 10 μg L⁻¹, is exceeded at least once and as many as three times at seven of the ten sites during the 2018 sampling season. Although the database solubility of hydroxypyromorphite is exceeded in most samples, it appears this may be the result of major ion substitutions in the hydroxypromorphite that forms in the Kırklareli stream which increases the effective solubility of lead in the stream.

: The objective of this work is to elucidate the role of partnerships and the number of partners necessary for lead user innovation outcomes. Lead user theory identifies these users as being ahead of market trends and experiencing significant benefits from innovating. So far, most lead user research has concentrated on firms and not individual lead users’ perspective. Data were obtained using a quantitative design during which 321 respondents participated. The SPSS software was used to analyze the data and determine significance. These findings indicate a connection between number of partners and lead user innovation success. This demonstrates that number of partners is significant in determining the success or failure of an innovation. This study provides empirical evidence that the number of partners is an essential factor that influences the success of innovation, and establishes the absolute numbers for achievement of successful innovation. Future studies must investigate the possible implications of integrating the partner variables with other characteristics of the lead user.

Lead halide perovskite has become a promising candidate for high-performance photodetector (PD) applications due to its attractive optical and electrical properties such as high optical absorption coefficient, high carrier mobility, and long carrier diffusion length. However, the presence of highly toxic lead in these devices has limited their practical applications and even hindered their progress toward commercialization. Therefore, the scientific community has been committed to searching for low-toxic and stable perovskite-type alternative materials. Lead-free double perovskite materials, which are still in the preliminary stage of exploration, have achieved inspiring results in recent years. In this review, we mainly focused on two types of lead-free double perovskite based on different Pb substitution strategies, including A2M(I)M(Ⅲ)X6 and A2M(IV)X6. We reviewed the research progress and prospects of lead-free double perovskite photodetectors in the past three years. And more importantly, from the perspective of optimizing inherent defects in materials and improving device performance, we proposed some feasible pathways and made an encouraging perspective for the future development of lead-free double perovskite photodetectors.

Anthropogenic lead pollution is an environmental problem that threatens the quality of soils and waters and endangers living organisms in numerous surface and subsurface habitats. Lead coprecipitation on mineral surfaces through dissolution-recrystallization processes has long term effects on lead bioavailability. Gypsum and calcite are among the most abundant and reactive rock forming minerals present in numerous geological settings. In this work, we study the interaction of slightly acidic (pHi = 5.5) Pb-bearing aqueous solutions ([Pb]i = 1 mM and 10 mM) with crystals of gypsum and /or calcite under atmospheric conditions. This interaction results in a reduction of the concentration of lead in the liquid phase due to the precipitation of newly formed Pb-bearing solid phases. The extent of this Pb removal mainly depends on the nature of the primary mineral phase involved in the interaction. Thus, when gypsum is the only solid phase initially present in the system the Pb-bearing liquid-gypsum interaction results in Pb removals in the 98-99.8 % range, regardless of [Pb]i. In contrast, when the interaction takes place with calcite, Pb removal strongly depends on [Pb]i. It reaches 99% when [Pb]i = 1 mM while it is much more modest (⁓13%) when [Pb]i = 10 mM. Interestingly, Pb-removal is maximized for both [Pb]i (99.9 % for solutions with [Pb]i = 10 mM and 99.7% for solutions with [Pb]i = 1 mM) when Pb-polluted solutions simultaneously interact with gypsum and calcite crystals. Despite the large Pb removals found in most of the cases studied, the final Pb concentration ([Pb]f) in the liquid phase always is well above the maximum permitted in drinking water (0.1 ppm), with the minimum ([Pb]f = 0.7 ppm) being obtained for solutions with [Pb]i =1 mM after their interaction with mixtures of gypsum and calcite crystals. This result suggests that integrating the use of mixtures of gypsum-calcite crystals might help to develop more efficient strategies for in-situ decontaminating Pb-polluted waters through mineral coprecipitation processes.

Adding zinc (II) and formate anions improves the thermal phase-stability of alpha-FAPbI3 materials and the spin-coated thin films of such doped FAPbI¬3 show an increased emission lifetime of up to 3.7 microsecond on quartz. This work investigates the effects of zinc and formate on the stability and time resolved photoluminescence of FAPbI3 perovskites for solar cell applications. Perovskite samples with varying concentrations of zinc and formate were made by incorporating different amounts of zinc formate and zinc iodide and characterized with XRD. Doping levels of 1.7% Zn(II) and 1.0% formate (relative to Pb) seem optimal. The thermal stability of the perovskite powders and thin films were assessed. XRD was virtually unchanged after 6 months. The time-resolved photo-luminescence spectroscopy of the doped spin-coated perovskite samples is reported. The results show that synergy between an anionic and a cationic dopant can take place, making the perovskite thermally more stable with a longer charge carrier lifetime.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

There has recently been interest in the development of small-molecule inhibitors of the oligomerization of Bacillus anthracis protective antigen for therapeutic use. Some of the proposed lead compounds have, however, unfavorable solubility in aqueous medium, which prevents their clinical use. In this computational work, we have designed several hundreds of derivatives with progressively higher hydrosolubility and tested their ability to dock the relevant binding cavity. The highest-ranking docking hits were then subjected to 125 ns-long simulations to ascertain the stability of the binding modes. Several of the potential candidates performed quite disappointingly , but two molecules showed very stable binding modes throughout the complete simulations. Besides the identification of these two promising leads, these molecular dynamics simulations allowed the discovery of several insights that shall prove useful in the further improvement of these candidate towards higher potency and stability.

The BIOTON® biochar, produced by a wood biomass pyrolysis process, usually applied as a soil amendment, was investigated for a novel application, i.e. the adsorption of lead from contaminated solutions. The experimental activity firstly included the physical-chemical characterization of BIOTON®; SEM images were also obtained to highlight its internal structure. The adsorption process was investigated through batch and column experiments. Adsorption kinetics showed a very rapid achievement of the equilibrium conditions, i.e. at 2h and 4h for 50 mg/L and 100 mg/L initial Pb concentration, respectively. Complete removal also occurred within the same time. The Brunauer–Emmett–Teller model better fitted the equilibrium data for both Pb concentrations, whereas the kinetics were best represented by the pseudo second order model. The column tests showed that the addition of biochar as adsorbent media within the bed significantly extended the time of breakthrough and exhaustion, with respect to the column filled with soil only. The adsorption capacities of BIOTON® versus lead solutions was found to be comparable to that reported for commercial adsorbents. Therefore, BIOTON® can be considered a valid option, with the additional benefit to reduce the environmental impact since allows to recover a residue which alternately would need to be disposed of.

Adopting banana peel as raw material, the adsorption properties of banana peel hydrothermal carbon modified with KOH solution for lead ions in aqueous solution were studied. The surface structure and functional groups of the modified hydrothermal carbon were analyzed by XRD and SEM. The results showed that the banana peel hydrothermal carbon prepared from 0.5 mol/L KOH solution had large pores, and its adsorption capacity reached 42.92 mg/g at a pH value of 6; When the concentration of KOH solution is 0.5 mol/L, the solid liquid ratio is 2 g/L, the adsorption capacity reaches 21.39 mg/g, and the adsorption rate reaches 82.74%; When the concentration of lead solution increased to 100 mg/L, the adsorption capacity of modified hydrothermal carbon for lead ions decreased to 78.26%; The equilibrium adsorption time of lead ion in solution on phosphoric acid modified hydrothermal carbon from banana peel was 250 minutes, and the adsorption process met the quasi second order kinetic model and Freundlich isotherm equation, with an equilibrium adsorption rate of 88.62%. The adsorption of lead ions in solution by KOH modified hydrothermal carbon is mainly chemical physical adsorption.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

In this study, fig leaves, zeolite and alginate were used to prepare a biocomposite for the adsorption of Pb(II) ions from aqueous solutions. Effects of various parameters on the biosorption process such as pH, temperature, initial lead concentration and contact time have been investigated. Maximum uptake of Pb(II) ions (85%) has been achieved at pH 6, with 25 mg/L of initial concentration and at a temperature of 288.15 K. Among the applied models, the data correlated well with Freundlich and D-R models and it was established that the biosorption was physical in nature. The amount of adsorbed lead per gram of sorbent was found to be 150.3 mg/g. Thermodynamic parameters showed the exothermic heat of biosorption and the feasibility of the process. Results have suggested that the prepared biosorbent possesses promising biosorption potential.

An ambitious citizen-science effort in the city of Indianapolis (Indiana, USA) led to the collection and analysis of a large number of samples at the property scale, facilitating the analysis of differences in soil metal concentrations as a function of property location (i.e., dripline, yard, and street) and location within the city. This effort indicated that dripline soils had substantially higher values of lead and zinc than other soil locations on a given property, and this pattern was heightened in properties nearer the urban core. Soil lead values typically exceeded the levels deemed safe for children’s play areas in the US (<400 ppm), and almost always exceeded safe gardening guidelines (<200 ppm). As a whole, this study identified locations within properties, and cities, that exhibited the highest exposure risk to children, and also exhibited the power of citizen science to produce data at a spatial scale (i.e., within a property boundary) that is usually impossible to feasibly collect in a typical research study.

The volume of electronic waste (e-waste) received in Nigeria is reportedly on the increase and the effects on environmental health are yet to be fully ascertained. This study aimed to investigate haematological indices, lead and serum iron levels in workers occupationally exposed to electronic wastes in South-South, Nigeria. In this pilot study, 104 participants were enrolled from Benin City, South-South Nigeria; consisting of 63 E-waste Workers (EW) sex- and aged-matched with 41 Unexposed Participants (Control). Blood levels (5 mL) of the metals (lead and iron) were determined using Inductively Coupled Plasma-Mass Spectrometry while the haematological parameters [white blood cells (WBC), Lymphocytes ( LY); monocytes (MO), granulocytes(GR), red blood cells (RBC), haemoglobin (Hgb), haematocrit (HCT), mean cell volume (MCV), mean cell haemoglobin (MCH), mean cell haemoglobin concentration (MCHC) and platelets (PLT)] were determined using standard methods. Results obtained from this study show a significantly low serum iron (11.5 ± 2.14 µg/dL) in the EW compared with Control (168.9 ± 2.39 µg/dL); while blood lead level in EW (1.07±0.02 µg/dL) was significantly elevated compared with Control (0.72 ± 0.12). Total WBC and RBC, HCT, MO and MCV were all significantly elevated in EW compared with Control while LY and PLT in the EW were significantly decreased compared with Control. This study concludes that chronic occupational e-waste exposure may increase blood lead level, lower serum iron status and may have adversely altered some important haematological parameters in the studied population.

We evaluated the association of blood pressure with blood levels of cadmium, lead, and cadmium and lead together (cadmium+lead) in a representative sample of adolescents from Korea by use of 2010-2016 data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study enrolled adolescents aged at 10-18 years-old who completed a health examination survey and had blood measurements of lead and cadmium. The association of adjusted mean differences in diastolic and systolic blood pressure with doubling of blood lead and cadmium were estimated by regression of blood pressure against log₂-transformed blood metals and their quartiles after covariate adjustment. Adjusted odds ratios for prehypertension were calculated for log₂-transformed blood levels of lead and cadmium and their quartiles. Our analysis of adolescents in Korea indicated that blood levels of lead and cadmium were not significantly associated with increased blood pressure or risk of pre-hypertension. However, the cadmium+lead level was associated with pre-hypertension. Previous studies showed that blood levels of lead and cadmium were associated with increased blood pressure and risk of hypertension in adult populations. We found no such effect in Korean adolescents, although the cadmium+lead level was associated with prehypertension. These differences may be because adolescents generally have lower levels of these blood metals or because adolescents only rarely have hypertension.

This study presents a novel polyurethane-activated carbon composite (PACC) as an effective and sustainable adsorbent for treating lead-ion-contaminated waters. The PACC was characterized using SEM-EDX, FTIR, BET, XRD, and TGA to evaluate its physicochemical and thermal properties. Furthermore, the PACC was employed in an experimental column adsorption setup to investigate its adsorption performance and to develop a dynamic method suitable for industrial implementation. Parameters such as bed height (50, 100, 150 mm), flow rate (4, 6, 8 mL min-1), pH (2, 4, 6), and initial metal ion concentrations (10, 50, 100 mg L-1) were examined. The experimental data exhibited strong agreement with the Thomas and Yoon-Nelson models (R2 ≥ 0.96), indicating efficient adsorption mechanisms. Remarkably, the depleted adsorbent has the potential for facile regeneration without substantial loss in capacity. The PACC demonstrated excellent adsorption performance for lead ions in aqueous solutions in a fixed-bed column system. Thus, the novel PACC material holds potential for scalable application in industrial settings to address water pollution challenges, especially in regions with uncontrolled effluent discharge.

In principle, modular or integral character of manufacturing lines depends on topological designs of products and determined operation tasks. On the other hand, in specific situations there is an articulated need for modular design in smart manufacturing systems, since modular layouts are a crucial step towards agile production via smart manufacturing. The aim of this paper is to explore how the modular layout relates to manufacturing lead time (MLT) and to operational complexity of smart manufacturing systems. For this purpose, topologically different models of alternative process layouts were simulated and tested, while MLT values were obtained using Tecnomatix Plant Simulation. Obtained positive findings of this research could be useful not only in selection of the most suitable process design from the alternative ones, but especially in deepening knowledge and better understanding of the concept of optimal network modularity.

Studies suggest that elevated postnatal blood lead levels (BLLs) are negatively associated with child growth. This study aimed to investigate associations of childhood BLLs at age one-year and growth outcomes at age six-years (n=661) in a cohort of children in Allada, Benin. The growth outcomes studied are weight-for-age Z-score (WAZ), height-for-age Z-score (HAZ) and BMI-for-age Z-score (BMIZ), head circumference (HC), underweight, stunting, and wasting. Multivariable regression models examined associations between blood lead levels, growth outcomes with adjustment for potential confounders. The geometric mean BLLs was 59.3 μg/L and 82% of children had BLLs &gt;35 μg/L at one year. After adjusting for confounding factors, no association was found between BLLs quartiles and HAZ, WAZ, BMIZ, and height and weight growth velocities. However, boys in the highest quartile had 1.02 cm lower HC (95% CI: [-1.81, -0. 24]) as compared to those in the lowest quartile with a dose-response trend across quartiles (Ptrend =0.02). Furthermore, an increased risk of being stunted was observed in children in the highest quartile of exposure compared to the first (OR: 2.43; 95% CI: [1.11 – 5.33]) with a dose-response trend (Ptrend =0.03). Blood lead was found to be associated with an increased risk of childhood stunting and lower head circumference in a resource-limited setting.

Considering that the electric refrigeration temperature range of 0.94BNT-0.06BT ceramic materials is 100~140˚C, the electric refrigeration performance of the 0.94BNT-0.06BT ceramic material system was modified by LiNbO3 doping to reduce the cooling temperature. As a result, the refrigeration temperature range of the 0.94BNT-0.06BT ceramic material system was lowered to 25~80 ˚C, achieving its cooling effect near room temperature, and in this temperature range, the adiabatic temperature changes ∆T&gt;0.6K.

The stability issues in the widely known organic inorganic halide perovskite, CH3NH3PbI3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs2AgBiBr6 and Cs2TiBr6 is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide bandgap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, bandgap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

Background: Although the link between environmental lead exposure and several patterns of cardiovascular disease (CVD) has been reported, its association with silent myocardial infarc-tion (SMI) has not been explored. We aimed to assess the association between blood lead levels (BLL) and risk of SMI. Methods: This analysis included 7283 (mean age 56.1±2.52 years, 52.5% women) participants from the Third National Health and Nutrition Examination Survey who were free of clinical CVD. Ascertainment of BLL done using graphite furnace atomic absorption spectrophotometry. SMI defined as ECG evidence of MI without history of MI. Multivariable lo-gistic regression analysis was used to examine the association between SMI and BLL. Results: SMI was detected in 120 participants corresponding to an unweighted prevalence of 1.65%. Par-ticipants with higher levels of BLL had higher prevalence of SMI (0.4%, 0.9%, and 2.4% across BLL tertiles; p-value

The integration of bioinformatics in drug discovery has revolutionized the field of pharmaceutical research. The use of computational tools and techniques has enabled researchers to analyze vast amounts of data, identify potential drug targets, and design new drugs with greater precision and efficiency. The integration of bioinformatics has also facilitated the development of personalized medicine, where drugs can be tailored to individual patients based on their genetic makeup. However, there are still challenges that need to be addressed, such as the need for more accurate predictive models and the ethical considerations surrounding the use of patient data. Overall, the integration of bioinformatics in drug discovery holds great promise for improving human health and advancing our understanding of disease mechanisms. In this mini-review, we discuss how Bioinformatics plays a crucial role in each step of drug discovery by providing tools and techniques to analyze large amounts of data generated from various sources, as well as the challenges and the opportunities offered by bioinformatics.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

Clean water is now very rare due to the increased water pollution causing many diseases. Heavy metals mainly lead from industrial waste i.e. batteries, cable sheaths, machinery manufacturing, shipbuilding, lead oxide and radiation protection is accountable & largely contributed lead in river and canal waters. Presence of lead in water is hazardous to life due to many reasons. It can cause cancer, weakness, anemia, kidneys, high blood pressure and nerve diseases. Inorganic lead is reported to me more dangerous than organic one. Industries including batteries, cable sheaths, machinery manufacturing etc. drains water that has soluble lead ranging from 200 – 500 mg/L. The safe limit of lead in water is about 0.015 mg/L. Pakistan is a country rich in minerals. It has about 3.5 MT of Kaolin (Clay) deposits situated at Nagar Parker region of Sindh, Pakistan. This indigenous material is being used to produce ceramic products and in paper making. Now we use this mineral source to remove lead from water by adsorption. Kaolin clay can be used as an adsorbent due to its unique structure. XRF technique is employed for clay characterization. Resultants will be analyzed by UV – Vis Spectrophotometry.

Lead (Pb) is a non-essential, highly toxic, and persistent element widely recognised as one of the most concerning pollutants, and it is listed in the Priority List of Hazardous Substances. Widespread environmental contamination from Pb is a serious issue for human health and wildlife. The liver, a key compartment for metal detoxification and excretion, is also the organ in which Pb mainly accumulates in fish. Herein, we investigated for the first time the morphological and functional injuries induced in zebrafish (Danio rerio) liver by two very low and environmentally relevant concentrations of Pb (2.5 and 5 μg/L) after 48, 96, and 192 hours of exposure. We showed significant histological alterations in all the exposed samples, also demonstrating that the extent of injuries increased with dose and exposure time. The most common modifications observed were congestion of blood vessels and sinusoids, cytoplasmic vacuolizations, parenchyma dyschromia, and macrophage proliferation. Pb administration also resulted in a significant increase in lipid content and the upregulation of key genes involved in metal detoxification (mtf1) and the defensive response against oxidative stress (sod1 and cat). We showed that even very low doses of Pb can disrupt liver morphology and function.

This field study aimed to assess the base line conditions of a long-term polluted shooting range in Argentina polluted with 428 mg kg-1 lead (Pb), to evaluate the establishment and development of Helianthus petiolaris plants and address the efficacy of the phytomanagement strategy through: i) element accumulation in plant tissues; ii) rhizosphere bacterial diversity changes by Illumina Miseq™ and iii) floral water and essential oil yield, composition and element concentration by GC-MS and ICP. After one life cycle growing in the polluted sites, in the roots of Helianthus petiolaris plants Pb concentration was between 195 and 304 mg kg-1 Pb. Only a limited fraction of the Pb was translocated to the aerial parts. The predominance of the genus Serratia in the rhizosphere of Helianthus petiolaris plants cultivated in the polluted sites and the decrees of the essential oil yield were some effects significantly associated with soil Pb concentration. No detectable Pb concentration was found in the floral water and essential oil obtained. Extractable Pb concentration in the soil reduced between 28-45 % after the harvest.

Emergence of multi drug resistant (MDR) and extensively drug resistant (XDR) Mycobacterium tuberculosis poses a serious threat to TB control as the available treatment options are less effective in these cases. Therefore, new strategies are required for identification of new drugs and drug targets. The M. tuberculosis dihydrodipicolinate synthase is a putative drug target with no potent inhibitor. Here in this study, we have used a comprehensive computational approach to identify small molecule inhibitors and validated them in vitro. As similar structures tend to have similar functions, therefore 3 approaches, namely, (a) known inhibitor-based approach, (b) substrate analogues, (c) product analogues were used for compound screening from various chemical libraries. The fourth approach we have taken is fragment library screening.In vitro studies revealed that β-hydroxypyruvic acid tartronic acid are inhibitors of Mtb-rDapA with maximum inhibition 48% and 51% at 500µM concentrations respectively. We have also observed that β-hydroxypyruvic acid is a time dependent inhibitor of Mtb-rDapA. Further, thermal shift assays showed that β-hydroxypyruvic acid interacts with Mtb-rDapA and the thermal stability of Mtb-rDapA shifted by 3˚C. Among the product analogues of Mtb-DapA, dipicolinic acid showed to bind to Mtb-rDapB shifting thermal stability of Mtb-rDapB by 0.5˚C in binding. Additionally, we have designed a new approach by combining substrate and product analogues to achieve better inhibitions. In vitro assays validated that this combination approach increased maximum inhibition up to 100%. We envision that these compounds would serve as potent leads for tuberculosis drug discovery.

Lead pollutants mainly from urban agricultural practices, Leaded paints, Leaded fuels spillages, Lead-contaminated air, soils, and water sources pause a health threat to urban children in Uganda. Prolonged Lead exposure affects iron metabolism, by competitively blocking iron absorption leading to anemia. Blood Lead (BL) inhibits key enzymes ferrochelatase and aminolevulinic acid dehydrogenase (ALAD) involved in hemoglobin (Hb) biosynthesis even at very low levels. Lead poisoning and malaria infection geographically overlap, and both produce similar hematological outcome especially in children. Malaria parasites cause anemia by destroying parasitized red blood cells, therefore, co-existence of BL and malaria parasites infection worsens the anemia status of the host. This study aimed at expounding the extent of heme synthesis inhibition by BL levels among a study group of malaria positive children by measuring levels of free erythrocyte protoporphyrin (FEP) in blood samples. Briefly venous blood samples from 198 children were analyzed for malaria parasite densities by the thick smear method, hemoglobin (Hb) concentrations determined by the standard cyan methemoglobin method, BLL were analyzed on an atomic absorption spectrophotometer and FEP levels were fluorometrically measured. The results showed means of BLL (9.3 µg/dL), Hb (7.5 g/dL), FEP/Hb (8.3 µg/g) and parasite density (PD) (3.21×10³ parasites / µL) among the study group. A majority of 151/198 (76.3%) of the children were moderately anemic while 8/198 (4%) were severely anemic. There was weak correlation between PD and Hb (R²= -0.15, P-value < 0.001), as compared to one between FEP/Hb and Hb (R²= -0.6, P-value=0.001). The study concludes that BL is a significant contributor to malaria anemia and should be considered in the management of anemia in malaria-endemic areas.

Environmental lead exposure is a population health concern in many low- and middle-income countries. Lead is found throughout Myanmar and prior to the 1940s, the country was the largest producer of lead worldwide. The aim of this study was to examine any potential association between lead mining and adult literacy rates at the level of the 330 townships in Myanmar. Townships were identified as lead or non-lead mining areas and 2015 census data were examined with association being identified using descriptive, analytical and spatial statistical methods. Overall, there does appear to be a significant relationship between lead mining activity and adult literacy levels (P<0.05) among townships with both low access [OR= 2.701 (1.136-6.421)] as well as townships with high access to safe sanitation [OR=18.40 (1.794-188.745)]. LISA cluster maps confirm these findings. This exploratory analysis is a first step in the examination of potential environmental lead exposure and its implications in Myanmar.

The accumulation of high levels of lead or lead ions in a human body is harmful, particularly to children. Its neurotoxic effect is profound, damaging the central and peripheral nervous systems, resulting in stunted growth, behavioral problems and learning disabilities. The major source of lead or lead ions comes from the drinking water and tap water. The assessment of the water quality, including lead or lead ion content, is usually completed by a regional water department professional. This assessment is time-consuming and requires expensive instruments and skilled operators. Therefore, there is a need to produce a simple-use and relatively inexpensive method to detect lead or lead ions in water samples. This research has developed a simple-use, cost effective sensor system for the detection of lead ions in tap water. An under-potential deposited bismuth sub-layer on a thin gold film based electrochemical sensor was designed, manufactured and evaluated. Differential pulse voltammetry (DPV) measurement technique was employed in this detection. Tap water from the Cleveland, Ohio, USA regional water district was the test medium. Concentrations of lead ion in the range of 8 X 10^-8 M to 8 x 10^-4 M were evaluated. This DPV detection system required 3 -6 minutes to complete the detection measurement. A longer measurement time of 6 minutes was used for the lower lead ion concentration. The selectivity of this lead ion sensor was very good, and Fe III, Cu II, Ni II and Mg II at a concentration level of 5×10^-4 M did not interfere with the lead ion measurement.

It is known that exposure to heavy metals such as lead (Pb) and cadmium (Cd) has several adverse effects, particularly on the human reproductive system. Pb and Cd have been associated with infertility in both men and women. In pregnant women, they have been associated with spontaneous abortion, preterm birth, and impairment of the development of the fetus. Since these heavy metals come from both natural and anthropogenic activities and their harmful effects have been observed even at levels of exposure, their exposure remains a public health issue, especially for the reproductive system. Given this, the present study aimed to investigate the potential reproductive effects of Pb and Cd levels in the follicular fluid (FF) of infertile women and no-smokers exposed to heavy metals for professional reasons or living in rural areas near landfills and waste disposal areas, to correlate the intrafollicular presence of these metals with possible alterations in the ultrastructure of human cumulus-oocyte complexes (COCs), probably responsible of infertility. Blood and FF metals were measured using atomic absorption spectrometry. COCs corresponding to each FF analyzed were subjected to ultrastructural analyses by transmission electron microscopy. We demonstrated for the first time that intrafollicular levels of Pb (0.66 µg/dL to 0.85 µg/dL) and Cd (0.26 µg/L - 0.41 µg/L) could be associated with morphological alterations of both the oocyte and CCs ultrastructure. Since blood Cd levels (0.54 µg/L - 1.87 µg/L) were above the current reference values established by the guidelines of the Agency for Toxic Substances and Disease Registry (ATSDR) and the Environmental Protection Agency (EPA), whereas blood Pb levels (1.28 µg/dL - 3.98 µg/dL) were below the ATSDR reference values we believe that these alterations could be due especially to Cd, even if we cannot exclude a possible additional effect of Pb. Our results highlighted that oocytes were affected in maturation and quality, whereas CCs showed scarcely active steroidogenic elements. Regressing CCs, with cytoplasmic alterations, were also numerous. According to Cd's endocrine-disrupting activity, the poor steroidogenic activity of CCs might correlate with delayed oocyte cytoplasmic maturation. So, we conclude that levels of heavy metals in the blood and the FF might negatively affect fertilization, embryo development, and pregnancy, compromising oocyte competence to fertilization both directly and indirectly, impairing CC steroidogenic activity, and inducing CC apoptosis.

Autism Spectrum Disorder (ASD), a neurodevelopmental disorder characterized by persistent deficits in social interaction and communication manifests in early childhood and is followed by restricted and stereotyped behaviors, interests or activities in adolescence and adulthood (DSM-V). Although genetics and environmental factors have been implicated, the exact causes of ASD have yet to be fully characterized. New evidence suggests that dysbiosis or perturbation in gut microbiota (GM) and exposure to lead (Pb) may play important roles in ASD etiology. Pb is a toxic heavy metal that has been linked to a wide range of negative health outcomes including anemia, encephalopathy, gastroenteric diseases and more importantly cognitive and behavioral problems inherent to ASD. Pb exposure can disrupt GM, which is essential for maintaining overall health. GM, consisting of trillions of microorganisms, has been shown to play a crucial role in the development of various physiological and psychological functions. GM interacts with the brain in a bidirectional manner referred to as “Gut-Brain Axis (GBA).” In this review, following a general overview of ASD and GM, the interaction of Pb with GM in the context of ASD is emphasized. Potential exploitation of this interaction for therapeutic purposes is also touched upon.

Understanding the strength of the associations between perceived risk and individuals’ behavioral intentions to protect their health is important for determining appropriate risk communication strategies in communities impacted by lead contamination. We conducted a survey within communities of northern Idaho, USA (n = 306) near a Superfund megasite with legacy mining contamination. We empirically test a theoretical model based on the Health Belief Model. Survey respondents had higher intentions to practice health protective behaviors when they perceived the risk of lead contamination as severe, recognized the benefits of health protective behaviors, and considered the risks of lead contamination. Women reported higher behavioral intentions than men, but age and mining affiliation did not have an association. Survey comments indicated that perceptions about the long-term environmental remediation in the region influenced risk perceptions. Understanding risk perceptions, behavioral intentions, and related factors can aid public health agencies in tailoring risk communication for increasing protective behaviors in mining-impacted communities internationally.

In this paper, the effect of Bi₂O₃ doping on the mechanical properties of PbO ceramic pellets was studied. For this purpose, different ratios of Bi2O3/PbO (i.e., xBi2O3–(1-x)PbO, where x is 0, 1, 3, 5, 7 wt%) were fabricated and sintered at 570, 620, and 670°C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for the aforementioned compositions. Phase compositions, microstructures, and worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi₂O₃ for optimal sintering are 620°C and 3 wt%, respectively. The hardness of the 3 wt% Bi2O3–97 wt% PbO ceramic was 717 MPa, which is about four times higher than the hardness of pure PbO; in addition, the strength of the composites was 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. Results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

Milling and mining metal ores are major sources of heavy metal contamination. The Spring River and its tributaries in southeast Kansas are contaminated with Pb, Zn, and Cd as a result of 120 years of mining activities. Trace metal transformations and cycling in mine waste materials greatly influence their mobility and toxicity and affect plant productivity and human health. It has been hypothesized that under reduced conditions in sulfate-rich environments, these metals can be transformed into their sulfide forms, thus limiting mobility and toxicity. We studied biogeochemical transformations of Pb, Zn and Cd in flooded subsurface mine waste materials, natural or treated with organic carbon (OC) and/or sulfur (S), by combining advanced microbiological and X-ray spectroscopic techniques to determine the effects of treatments on the microbial community structure and identify the dominant functional genes involved in the biogeochemical transformations, especially metal sulfide formation over time. Samples collected from medium-, and long-term submerged columns were used for microarray analysis via functional gene array (GeoChip 4.2). The total number of detected gene abundance decreased under long-term submergence, but major functional genes abundance was enhanced with OC plus S treatment. The microbial community exhibited a substantial change in structure in response to OC and S addition. Sulfur-reducing bacteria genes dsrA/B were identified as key players in metal sulfide formation via dissimilatory sulfate reduction. Uniqueness of this study is that microbial analyses presented here in details are in agreements with molecular-scale synchrotron-based X-ray data supporting that OC-plus-S treatment would be a promising strategy for reducing metal toxicity in mine waste materials.

Obesity results in hepatic fat accumulation, i.e., steatosis. Besides the fat overload, impaired fatty acid β-oxidation also promotes steatosis. Fatty acid β-oxidation takes place in mitochondria and peroxisomes. Usually very long chain and branched-chain fatty acids are first oxidized in peroxisomes, and the resultant short chain fatty acids are further oxidized in mitochondria. Peroxisome biogenesis is regulated by peroxin 16 (PEX16). In liver-specific PEX16 knockout (Pex16Alb-Cre) mice, hepatocyte peroxisomes were absent, but hepatocytes proliferated, and liver mass was enlarged. These results suggest that normal liver peroxisomes restrain hepatocyte proliferation and liver sizes. After high fat diet (HFD) feeding, body weights were increased in PEX16 floxed (Pex16fl/fl) mice and adipose-specific PEX16 knockout (Pex16AdipoQ-Cre) mice but not in the Pex16Alb-Cre mice, suggesting that the development of obesity is regulated by liver PEX16 but not by adipose PEX16. However, it was previously reported that HFD-induced obesity in the Pex16AdipoQ-Cre mice was more severe than in the wild type mice, which was not observed until 27 weeks of HFD feeding. Thus, liver initiates the development of obesity, which is enhanced by abnormal adipocytes. HFD increased liver mass in the Pex16fl/fl mice but somehow reduced the already enlarged liver mass in the Pex16Alb-Cre mice. Basal levels of serum triglyceride, free fatty acids and cholesterol were decreased whereas serum bile acids were increased in the Pex16Alb-Cre mice, and HFD-induced steatosis was not observed in the Pex16Alb-Cre mice. These results suggest that normal liver peroxisomes contribute to the development of liver steatosis and obesity.

The solute carrier family 25 (SLC25) participates in the transport of metabolites and cofactors across the membranes of mitochondria, plastids, peroxisomes, and endoplasmic reticulum. By calling for genomic blocks involved in adjacent metabolic reactions, this report introduces gene clusters of the Slc25 subfamily 44, stilbene and chalcone synthases, and subunits of the mitochondrial electron transfer complexes. The Slc25A44 gene was found ubiquitously expressed and transcriptionally co-regulated with energy metabolism genes in human, mouse, and Arabidopsis thaliana. The Slc25A44s also had no homozygous missense mutation and were highly conserved at intra-species level with the majority of polymorphism present in the non-coding regions. When expressed in oocytes, AdSlc25A44 from Arachis duranensis showed transport activity for the common precursors of flavonoids, stilbenoids, and ubiquinone. Accordingly, AdSLC25A44 and its human orthologue HsSLC25A44 elevated the production of para-coumaric, 4-aminobenzoic, and 4-hydroxybenzoic acids in Saccharomyces cerevisiae strains designed to produce para-coumaric acid via different pathways. Moreover, the engineered SLC25 subfamily specific signature, i.e., AdSLC25A44^LWW206IQF, had a stronger effect on para-coumaric acid secretion than the native variant. Importantly, the aerobic growth-rate of S. cerevisiae was significantly higher when expressing the AdSLC25A44, HsSLC25A44, or AdSLC25A44^LWW206IQF. These results suggest that SLC25A44 is an essential mitochondrion-ER-nucleus zone transporter associated with metabolism of secondary metabolites and energy.

The human chromosome 11q13 (HSA 11q13) genomic locus is a major cancer hotspot and has been established as the most frequently altered by amplification in a variety of human cancers. The fatty acid desaturase genes (FADS1, FADS2 and FADS3) localize to the 11q12- 13.1 region. FADS2 activity is promiscuous, catalyzing biosynthesis of polyunsaturated and monounsaturated fatty acids, including unsaturated branched chain fatty acids (BCFA) by Δ6, Δ8, and Δ4 desaturation toward at least 16 substrates. Our main aim here is to review known and putative consequences of FADS2 dysregulation due to effects on the 11q13 locus in various cancer types. We searched PubMed and Google Scholar databases for articles that showed 11q13 amplification and studies reporting FADS2 function in various cancer types. FADS2 silencing causes synthesis of sciadonic acid (ScA, 5Z,11Z,14Z-20:3) in MCF7 cells and breast cancer in vivo. 5Z,11Z,14Z-20:3 is structurally identical to the eicosanoid precursor arachidonic acid (5Z,8Z,11Z,14Z–20:4) except it lacks the internal Δ8 double bond required for prostaglandin and leukotriene synthesis, among other eicosanoids. Melanoma, prostate, liver and lung cancer cells insensitive to SCD inhibition show increased FADS2 activity leading to sapienic acid (16:1n10) biosynthesis from 16:0. Elevated serum mead acid (20:3n-9) levels were found in more than a third of hepatocellular carcinoma patients, indicative of an unsatisfied demand for arachidonic acid, likely as a substrate for eicosanoids. A highly expressed circular RNA (hsa_circ_022382) within an exonic region of FADS2 is associated with shorter overall survival in colorectal cancer patients. Similarly, in lung cancer tissues circFADS2 RNA is highly expressed. Palmitic acid (16:0) is a common substrate for SCD and FADS2. FADS2 circular RNAs are at high levels in colorectal and lung cancer tissues. The evidence thusfar supports an effort for future research on the role of FADS2 as a tumor suppressor in a range of neoplastic disorders.

Choline is metabolized by the gut microbiota into trimethylamine (TMA), the precursor of pro-atherosclerotic molecule trimethylamine N-oxide (TMAO). Reduction of TMA formation has been shown to provide to cardioprotective effects, and some phytochemicals may produce such reduction. This study aimed to develop an optimized, high-throughput anaerobic fermentation methodology to study inhibition of choline microbial metabolism into TMA by phenolic compounds with healthy human fecal starter. Optimal fermentation conditions were: 20 % fecal slurry (1:10 in PBS), 100 M choline, and 12 h fermentation. Also, 10 mM of 3,3-dimethyl-1-butanol (DMB) was defined as a positive TMA production inhibitor, achieving a ~50 % reduction in TMA production. Gallic acid and chlorogenic acid reported higher TMA inhibitory potential (maximum of 80 -90 % in. TMA production inhibition), with IC50 around 5 mM. Nor DMB neither gallic acid and chlorogenic acid reduced TMA production through cytotoxic effects, indicating mechanisms such as altered TMA lyase activity or expression.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

The Lead-DBS imaging toolbox reconstructs the location of β-oscillations in the subthalamic nucleus (STN) in patients with Parkinson’s disease. The objective was to compare this probabilistic location with those of intraoperative monopolar β-oscillations (Vercise Cartesia directional electrodes, Boston Scientific). Also, the efficacy of stimulated structures in reducing motor symptoms were analysed. β-oscillations were computed from local field potentials [0.5-3kHz] by using shielded wires for monopolar recordings with an extracranial shielded reference. For each electrode contact, power spectral densities of the β-band [13-31Hz] were compared with those of all eight electrode contacts. The DISTAL, electrophysiological, and DBS target atlases of the Lead-DBS toolbox were applied to the reconstructed electrodes from preoperative MRI and postoperative CT. Thirty-six electrodes (20 patients: 7 female, 13 male; 16/20 both, 4/20 single STN) were analysed. Stimulation sites dorsal and/or lateral to the sensorimotor STN were most efficient. In 33/36 electrodes at least one contact was measured with stronger β-oscillations, 23 in or touching the ventral subpart of the probabilistic volume with β-oscillations, 10 not located in or touching but adjacent to this volume; in 3/36 electrodes, no contact was found with β-oscillations, they were distant from this volume. Monopolar local field potentials confirmed the ventral subpart of the probabilistic β-oscillations.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

Research on the lead halide-based perovskite solar cells have obtained considerable interest in photovoltaic industry owing to their higher efficiency, easy manufacturing, light-weight and low cost. However, these lead halide-based solar cells are not suitable to manufacture commercially because of the toxicity of lead-based materials. In this context, a lead-free perovskite, cesium-bismuth iodide (Cs₃Bi₂I₉) is considered as a potential alternative to the lead halide-based cell due to their non-toxicity and stability, but this perovskite cannot be matched with random hole transport layer (HTL) and electron transport layer (ETL) materials compared to lead halide-based perovskite because of their crystal structure and band gap. Therefore, in this study, performance comparison of different ideal HTL and ETL materials for Cs₃Bi₂I₉ perovskite layer were studied using SCAPS-1D device simulation on the basis of open circuit voltage, short circuit current, power conversion efficiency (PCE) and fill factor (FF) as well as several novel PSC configuration model were designed that can direct for further experimental research for PSC device commercialization. Results from this investigation reveals that the maximum efficiency of 20.96% is obtained for the configuration ITO/WS₂/Cs₃Bi₂I_9­/NiO/Au with optimized parameters such as thickness 400 nm, band gap 2.1eV, absorber layer defect density 10¹² cm^-3, donor density of ETL 10¹⁸ cm^-3 and the acceptor density of HTL 10²⁰ cm^-3.

Heterojunctions based on metal halide perovskites (MHPs) are promising systems for photocatalytic hydrogen evolution reaction (HER). In this work, we coupled Cs3Bi2Br9 nanocrystals (NCs), obtained by wet ball milling synthesis, with g-C3N4 nanosheets (NSs) produced by thermal oxidation of bulk g-C3N4 in air. These methods are reproducible, inexpensive, and easy to scale up. Heterojunctions with different loadings of Cs3Bi2Br9 NCs were fully characterized and tested for HER. A relevant improvement of H2 production with respect to pristine carbon nitride was achieved at low NCs levels reaching values up to about 4600 µmol g-1 h-1. This work aims to provide insights on the synthesis of inexpensive and high performing heterojunctions using MHP for photocatalytic applications.

This paper presents the results of an experimental study of the patterns of steel and lead shot transformation under the impact of environmental factors (two types of shot exposed alone and in combination with each other). The analyzed environmental factors include atmospheric precipitation of various acidity and soil solutions with a higher content of organic acids. This research demonstrated that steel shot is characterized by a high transformation rate that is an order of magnitude higher on average than the transformation rate of lead under the same conditions. The prevalence of the suspended iron form (excluding the interaction with organic acids) presents risks for such environmental components as soils and sediments and may be hazardous to the ambient air and natural waters in case of wind erosion and surface runoff from the catchment area. Furthermore, the joint presence of steel and lead shot mutually accelerates the corrosion of both metals, thus increasing the environmental risks.

In this article, a technology for producing wire and rod solder from 52In-48Sn alloy has been developed and investigated in the conditions of small-scale production. The use of direct extrusion of wire and rods instead of the traditional technology for producing solder, which includes pressing, rolling and drawing, can significantly reduce the fleet of required equipment. Using only a melting furnace and a hydraulic press, solder wires and rods can be produced in various sizes. Shortening the production cycle allows you to quickly fulfill small orders and be competitive in sales. The article developed a mathematical model of direct extrusion, which allows you to calculate: extrusion ratio, extrusion speed and pressing force. The results of modeling the process of extrusion of wire ∅2.00 mm and rods ∅8.0 mm made of 52In-48Sn alloy are presented. The temperature of the solder and the tool is simulation in software QForm based on the finite element method. Experimental results of manufacturing ∅2.0 mm solder wire and ∅8.0 mm rods are presented. The microstructure of the direct extruded solder is a eutectic of phases γ and β. Energy-dispersive X-ray spectroscopy (EDS) mapping of the 52In-48Sn alloy showed that the solder obtained by direct extrusion has a uniform distribution of structural phases. The developed technology can be used in the manufacture of wires and rods from other low-melting alloys.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

Lead exposure is associated with poor cognitive development in children. Very few studies in sub-Saharan Africa (SSA) have studied blood lead levels (BLLs) and non-gasoline sources of exposure in children. Data from a birth cohort in Benin (2011-2013) suggested that 58% of one-year-old children had BLLs > 50 ug/L. We aimed to investigate the prevalence of elevated BLLs (>50 µg/L and >100 µg /L) among 425 of these children at six-years-of-age in 2016-18 and to compare BLLs between age one-year and six-years and study sources of lead at six years. BLLs were analyzed by inductively coupled plasma mass spectrometry. Multiple linear regression and quantile regressions were used to study potential sources of lead. The prevalence of BLLs >50 µg/L in children was 59.5% [Geometric Mean (GM) 56.4 µg/L, 95% CI: 54.1 - 58.7] at six years of age compared to 54.8% [GM 56.5 µg/L, 95% CI: 53.4-59.6] at one year of age. The prevalence of children with BLLs >100 µg/L decreased from 14.4% at one year of age to 8.2% at six years of age. After adjustment for all other covariates, consumption of peanut more than once per month was significantly associated with a 22.0% (95% CI: 4.6, 42.5) increment in BLLs at six years compared with no consumption. Consumption of bushmeat killed by lead bullets at six years was associated with an increase in the higher percentiles of BLLs (P75) compared with the absence of this source. Other potential sources of lead associated with BLLs with marginal significance were consumption of rice, paternal occupational exposure, and the presence of activity with the potential use of lead. This prospective cohort confirms the persistently high prevalence of elevated BLLs in children residing in a rural region in the south of Benin as well as the presence of multiple and continuous sources of lead. These results highlight the need for prevention programs to reduce and eliminate lead exposure in children.

Despite the 12-lead electrocardiogram (ECG) being the gold standard in evaluating clinical presentations of arrythmias of various kinds, several notable limitations, namely in accuracy and localization, have recently garnered concern with respect to administering appropriate therapeutic measures. The following text puts these limitations under the spotlight, highlighting the difficulty and challenging nature of standard ECG analysis and therapeutic measures, while simultaneously showing a novel body surface electrocardiographic mapping system that utilizes 3D spatial imaging and pinpoint localization algorithms in order to compensate for the shortcomings of the standard ECG, thereby providing higher precision data collection. We provide a brief overview of the novel device in a selection of arrhythmic demographics, along with its validity and reliability, while illustrating the benefits and positive outcomes of its utility.

Fosmidomycin (FOS) is a naturally occurring compound active against the enzyme DXR in the MEP pathway, and using it as a template for lead structure design is an effective strategy in developing new active compounds. In this work, by replacing the hydroxamate unit of FOS with pyrazole, isoxazole and the related heterocycles that also have the metal ion binding affinity, while retaining the monophosphonic acid in FOS or replacing it with a bisphosphonic acid group, heterocycle-containing mono- and bisphosphonic acid compounds as FOS analogs were designed. The key steps involved in the facile synthesis of these FOS analogs include the Michael addition of diethyl vinylphosphonate or tetraethyl vinylidenebisphosphonate to β-dicarbonyl compounds and the subsequent cyclic condensation with hydrazine or hydroxylamine. Two additional isoxazolinone-bearing FOS analogs were synthesized by the Michaelis-Becker reaction with diethyl phosphite as a key step. The bioactivity evaluation on model plants demonstrated that several compounds have better herbicidal activities compared to FOS, with the most active compound showing a 3.7-fold inhibitory activity on Arabidopsis thaliana, while on the root and stalk of Brassica napus L. and Echinochloa crus-galli in pre-emergence inhibitory activity test, the activities of this compound were found to be 3.2- and 14.3-, 5.4- and 9.4-fold, respectively, and in post-emergency activity test on Amaranthus retroflexus and Echinochloa crus-galli, 2.2- and 2.0-fold inhibition activities were displayed. Despite the significant herbicidal activity, this compound exhibited a DXR inhibitory activity lower than that of FOS but comparable to that of other non-hydroxamate DXR inhibitors, and the dimethylallyl pyrophosphate rescue assay gave no statistical significance, suggesting a different target might be involved in the inhibiting process. This work demonstrates that using bioisosteric replacement can be considered a valuable strategy for discovering new FOS analogs that may have high herbicidal activity.

This work reports of the use of a bench scale chemostat (CSTR) in continuous mode and of a pilot scale membrane bioreactor (MBR) in fed-batch mode to intensively produce acetic and butyric acids using Cl. butyricum grown on synthetic media. These studies were then used to perform a cost estimation study of the MBR system to assess the potential economic impact of this proposed methodology. The MBR system was found highly productive reaching 37.88 g L-1 h-1 of acetic and 14.44 g L-1 h-1 of volumetric cell productivity, favoring acetic acid production to butyric at a ratio 3:1. The cost of preparation and production of carboxylic acids using this system was found as 0.0062 £PS/kg respectively and an up to 99% carbon recovery.

High seismic activity in the Himalayas and the increasing urbanization of its surrounding areas in the northern Indian region pose significant threats to both lives and properties. To mitigate the risk of seismic events, an earthquake early warning system can be used in the region. This system would be particularly beneficial to cities and towns in the mountainous and foothill regions that are located near earthquake sources. The government and the science and engineering community have re-sponded to this call by establishing the Uttarakhand State Earthquake Early Warning System (UEEWS). The system became fully operational on August 4, 2021, after being launched by the government of Uttarakhand. The UEEWS includes 170 accelerometers in the seismogenic part of the Uttarakhand region of the Himalayas. Ground motion data is transmitted to a central server through a dedicated private telecommunication network 24 hours a day, seven days a week.The system is designed to issue warnings for moderate to high-magnitude earthquakes via a mobile application installed on users' devices and sirens installed in government-owned public buildings. The UEEWS has successfully issued alerts for light earthquakes that occurred in the instrumented region and warnings for moderate earthquakes that occurred in the vicinity of the instrumented area. This paper provides an overview of the design of the UEEWS, details of the instrumentation, adaptation of attributes and their relation to earthquake parameters, the operational flow of the system, and information about the dissemination of warnings

The inner walls of drinking water distribution system (DWDS) are expected to be clean to ensure a safe quality of drinking water. In reality, complex physical, chemical and biological processes take place when water comes into contact with the pipe surface. This paper describes the impact of leaching different compounds from the water supply pipes into the drinking water and subsequent risks. Among these compounds there are heavy metals. It is necessary to prevent these metals to get into the DWDS. Those compounds are susceptible to impact the quality of the water delivered to population either by leaching dangerous chemicals into the water or by enhancing the development of microorganism growth on the pipe surface. The corrosion process of different pipes materials, scale formation mechanisms and the impact of bacteria formed in corrosion layers are discussed. Water treatment processes and the pipe materials also affect the water composition. Pipes materials act differently in the flowing and stagnation conditions. Also, they age differently (e.g metal based pipes are subjected to corrosion while polymer based pipes have a decreased mechanical resistance) and are susceptible to enhance bacterial film formation. This review helps to clarify what are the possible sources of compounds responsible for drinking water quality degradation. Also, it gives guidance on the measures that are needed to maintain a stable and safe drinking water quality.

Abstract: Background: The Hospital-at-home (HAH) model is a viable alternative for conven-tional in-hospital stays worldwide. Serum electrolyte abnormalities are common in acute pa-tients, especially in those with many comorbidities. Pathologic changes in cardiac electrophysi-ology pose a potential risk during HAH stay. Periodical Electrocardiogram (ECG) tracing is therefore advised, but few studies evaluated the accuracy and efficiency of compact, self-activated ECG devices in the HAH settings. This study aimed to evaluate the reliability of such a device in comparison to a standard 12-lead ECG. Methods: We prospectively recruited consecu-tive patients admitted to the Sheba Beyond, virtual hospital, in the HAH department, during a 3-month duration. Each patient underwent a 12-lead ECG recording using the legacy device, and a consecutive recording by a compact 6-lead device. Baseline patients’ characteristics during hospi-talization were collected. Level of agreement between devices was measured by Cohen’s Kappa coefficient for inter-rater reliability (Ϗ). Results: Fifty patients were included in the study. 26 (52%) had electrolyte disturbances. Abnormal D-dimer values were observed in 33 (66%) pa-tients, and 12 (24%) patients had elevated troponin values. We found a level of 94.5% raw agreement between devices with regards to nine of the options included in the automatic read-out of the legacy device. The calculated Ϗ was 0.72, classified as substantial consensus. The rate of raw consensus regarding ECG intervals’ measurement (PR, RR, QT) was 78.5% and the calculated Ϗ was 0.42, corresponding to a moderate level of agreement. Conclusion: This is the first report to our knowledge regarding the feasibility of using a compact, 6-Lead ECG device in the setting of HAH to be safe and bearing satisfying agreement level with a legacy, 12-lead ECG device, en-abling quick, accessible arrythmia detection in this setting. Our findings bear a promise to the future development of telemedicine-based hospital at home methodology.

Background: Trans-septal endocardial left ventricle lead placement is an alternative technique used capture the left ventricular endocardially but it is use is limited due lack of evidence, practice uptake and clinical trials. we evaluated the efficiency of the procedure, post procedural complication rate, rate of thromboembolic events as well as changes in echocardiographic parameters, brain natriuretic peptide (BNP) level and the New York Heart Association (NYHA) class. Results: TSLV lead implant is safe, improves ejection fraction, LVEDV, LVESV, LVIDd. Significantly reduces NTproBNP levels and NYHA class. Stroke rate was reported only in one patient (9%), noticeably, this particular patient was on DOAC rather than anti-vitamin K antagonists. In this group, patients, who were on Warfarin , were not reported to have any thrombo-embolic events. Discussion: Trans-septal endocardial LV lead implant in patients with a failed CS approach remains a viable alternative however, there is a higher risk of stroke amongst these patients, as well as more procedure related risk of complications compared to conventional CRT. The data analysis demonstrates that patients undergoing a TSLV lead implant due to a failed trans-venous approach have more advanced heart failure, defined by their higher NYHA class compared to conventional trans-venous CRT implant groups. Their pre TSLV implant, echocardiographic parameters are also worse compared to trans-venous CRT implant group

In response to long-lasting high levels of Metallic Trace Elements (MTEs) in urban soils, we expect soil invertebrates inhabiting urban environments to have evolved detection and avoidance and/or tolerance mechanisms to MTE pollution. In this study, I used artificial soils with concentrations of lead, zinc, copper, chromium and nickel that reflect pollution levels in soils of Parisian parks. Using choice experiments, I compared habitat preference (i.e. the occurrence of individuals in the polluted vs. unpolluted soil) and health status (i.e. body mass maintenance, mobility, mortality) between three species of endogeic earthworms – Apporectodea caliginosa, Apporectodea icterica and Allolobophora chlorotica – originating either from urban or rural grasslands. This study highlights a clear avoidance of MTE polluted soils in all three species, as well as MTE-induced health impairments, especially in A. chlorotica. Interestingly, earthworm response to MTE exposure only slightly differed between earthworms from urban and rural origin, suggesting the absence of widespread acclimatization or adaptation mechanisms to MTE pollution in cities. As a consequence, MTE pollution is expected to significantly shape earthworm spatial distribution in both urban and rural environments and, as a consequence, affect ecosystem functioning.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

Lead (Pb) is a toxic environmental heavy metal that induces serious clinical defect on all organs with the nervous system being the primary target. Curcumin is the main active constituent of turmeric rhizome (Curcuma longa) with strong antioxidant and anti-inflammatory properties. This study is aimed at evaluating the therapeutic potentials of curcumin on Pb-induced neurotoxicity. Thirty six male Sprague Dawley rats were randomly assigned into five (5) groups with 12 rats in the control (normal saline) and 6 rats for the lead treated group (LTG) (50 mg/kg lead acetate for 4 weeks), recovery group (RC) (50 mg/kg lead acetate for 4 weeks), treatment group 1 (Cur100) (50 mg/kg lead acetate for 4 weeks, followed by 100 mg/kg curcumin for 4 weeks) and treatment group 2 (Cur200) (50 mg/kg lead acetate for 4 weeks, followed by 200 mg/kg curcumin for 4 weeks) groups each. All experimental groups received the oral treatments through orogastric-tube on alternate days. Motor function was assessed using horizontal bar method while Pb concentration in the cerebellum of the rats were evaluated using ICP-MS techniques. Pb-administered rats showed significant decrease in motor scores, SOD activity with increase MDA levels and Pb concentration in their cerebellum with marked alterations in the histological architecture of the cerebellar cortex layers. However, treatment with curcumin improved the motor score, reduced Pb concentration in the cerebellum and ameliorates the markers of oxidative stress as well as restored the histological architecture of the cerebellum. The results this in study suggested that curcumin attenuates Pb-induced neurotoxicity via inhibition of oxidative stress and chelating activity.

Lead (Pb) is a toxic environmental heavy metal that induces serious clinical defect on all organs with the nervous system being the primary target. Curcumin is the main active constituent of turmeric rhizome (Curcuma longa) with strong antioxidant and anti-inflammatory properties. This study is aimed at evaluating the therapeutic potentials of curcumin on Pb-induced neurotoxicity. Thirty six male Sprague Dawley rats were randomly assigned into five (5) groups with 12 rats in the control (normal saline) and 6 rats for the lead treated group (LTG) (50 mg/kg lead acetate for 4 weeks), recovery group (RC) (50 mg/kg lead acetate for 4 weeks), treatment group 1 (Cur100) (50 mg/kg lead acetate for 4 weeks, followed by 100 mg/kg curcumin for 4 weeks) and treatment group 2 (Cur200) (50 mg/kg lead acetate for 4 weeks, followed by 200 mg/kg curcumin for 4 weeks) groups each. All experimental groups received the oral treatments through orogastric-tube on alternate days. Motor function was assessed using horizontal bar method while Pb concentration in the cerebellum of the rats were evaluated using ICP-MS techniques. Pb-administered rats showed significant decrease in motor scores, SOD activity with increase MDA levels and Pb concentration in their cerebellum with marked alterations in the histological architecture of the cerebellar cortex layers. However, treatment with curcumin improved the motor score, reduced Pb concentration in the cerebellum and ameliorates the markers of oxidative stress as well as restored the histological architecture of the cerebellum. The results this in study suggested that curcumin attenuates Pb-induced neurotoxicity via inhibition of oxidative stress and chelating activity.

Drinking water contamination of lead from various environmental sources, leaching consumer products and intrinsic water-pipe infrastructure is still today a matter of great concern. Therefore, new highly sensitive and convenient Pb²⁺ measurement schemes are necessary, especially for in-situ measurements at a low-cost. Within this work dye/ionophore/Pb²⁺ co-extraction and effective water phase de-colorization was utilized for highly sensitive lead measurements and sub-ppb naked-eye detection. A low-cost ionophore Benzo-18-Crown-6-ether was used, and a simple test-tube mix and separate procedure was developed. Instrumental detection limits were in the low ppt region (LOD=3, LOQ=10), and naked-eye detection was 500 ppt. Note, however, that this sensing scheme still has improvement potential as concentrations of fluorophore and ionophore were not optimized. Artificial tap-water samples, leached by a standardized method, demonstrated drinking water application. Implications for this method are convenient in-situ lead ion measurements.

Novel collector lead(II)-benzohydroxamic acid (Pb(II)-BHA) complexes in aqueous solution were characterized by using experimental approaches, including Ultraviolet-visible (UV-Vis) spectroscopy and electrospray ionization–mass spectrometry (ESI-MS), as well as first-principle density functional theory (DFT) calculations with consideration for solvation effects. The Job plot delineated that a single coordinated Pb(BHA)⁺ should be formed first, and the higher coordination number complexes can be formed subsequently. Moreover, the Pb(II)-BHA species can aggregate with each other to form complicated structures, such as Pb(BHA)₂ or highly complicated complexes. ESI-MS results validated the existence of Pb-(BHA)_n=1,2 under different solution pH values. Further, the first-principles calculations suggested that Pb(BHA)⁺ should be the most stable structure, and the Pb atom in Pb(BHA)⁺ will act as an active site to attack nucleophiles. These findings are meaningful to further illustrate the adsorption mechanism of Pb(II)-BHA complexes in mineral processing.

Lead, known as a metal with high neurotoxicity to children, cadmium, which is a carcinogenic and bioaccumulative contaminant, and arsenic, a class 1 carcinogenic according to the International Agency for Research on Cancer, are toxic elements (TEs) whose relevant route of exposure may be diet. We determined the bio-accessible fraction of lead, cadmium, and arsenic from the diet of preschool children from two day care centers (DCC). A cross-sectional study was conducted with 64 one–four-year-old children from two DCCs where the 24-h duplicate diet samples were collected. The diet samples were analyzed by ICP-MS for lead, cadmium, and arsenic total concentrations (n = 64) and their bio-accessibility were analyzed for a subsample (n = 10). The dietary intake (DI) mean for lead, cadmium, and arsenic were 0.18 ± 0.11 µg kg⁻¹ bw, 0.08 ± 0.04 µg kg⁻¹ bw, and 0.61 ± 0.41 µg kg⁻¹ bw, respectively. All DI calculated for TEs, considering total intake, were found lower than the tolerable limits (TL) (European Union, or World Health Organization, WHO, when applicable) except for one child’s Pb intake. Bio-accessibilities ranged between 0% to 93%, 0% to 103%, and 0% to 69%, for lead, cadmium, and arsenic, respectively. Although DI for TEs has been found lower than TL, these reference values have been recently decreased or withdrawn since it was for lead and arsenic whose TL were withdrawn by WHO.

High mountain areas are an appropriate indicator of anthropogenic lead (Pb), which can reach the remote mountain ranges through long distance atmospheric transport. We compared the content of Pb in ecologically equivalent rodent species from Tian-Shan with European mountain ranges Tatra, Vitosha and Rila mountains. We used bone tissues from terminal tail vertebrae of small rodents for detection of Pb levels by using electrothermal atomic absorption spectroscopy (AAS). The tail bones of Tian-Shan rodents had significantly lower Pb levels than snow voles from Tatra mountains, but there was no significant difference in comparison with Vitosha and Rila mountains. We can conclude that Tian-Shan shows lower pollution by Pb than Tatra mountains, what may be a reason of longer lasting industrialization of north-western Europe and strongly prevailing west winds in Tatra mountains.

Lignocellulosic biomass fractionation is typically performed using methods that are somehow harsh to the environment, such as in the case of the kraft pulping. In recent years, the development of new sustainable and environmentally friendly alternatives has grown significantly. Among the developed systems, bio-based solvents emerge as promising alternatives for biomass processing. Therefore, in the present work, the bio-based and renewable chemicals, levulinic acid (LA) and formic acid (FA), were combined to fractionate lignocellulosic waste (i.e., Maritime pine sawdust) and isolate lignin. Different parameters, such as LA/FA ratio, temperature, and extraction time, were optimized to boost the yield and purity of extracted lignin. The LA/FA ratio was found to be crucial regarding the superior lignin extraction from the waste biomass. Moreover, the increase in temperature and extraction time enhances the amount of extracted residue but compromises the lignin purity and reduces its molecular weight. The electron microscopy images revealed that biomass samples suffer significant structural and morphological changes, which further suggests the suitability of the new developed bio-fractionation process. Same was concluded by the FTIR analysis, in which no remaining lignin was detected in the cellulose-rich fraction. Overall, the novel combination of bio-sourced FA and LA has shown to be a very promising system for lignin extraction of high purity from biomass waste, thus contributing to extend the opportunities of lignin manipulation and valorisation into novel added-value biomaterials.

The food additive sorbic acid is considered as an effective preservative for certain cereal products, and propionic acid is commonly added in bakery wares, e.g. bread and fine bakery wares. The aim of this study is to develop and validate a new nuclear magnetic resonance spectroscopy (¹H NMR) method for routine screening and quantification of sorbic and propionic acids in bread and several bakery products for quality control purposes. Results showed that none of the screened samples contained higher concentrations than regulatory maximum limits. However, for some samples, labelling of preservatives was lacking or they were used in food categories, for which the use is not approved. It can be concluded that the developed NMR method can be used for routine screening of bakery products.

Sulfonated carbon was used as an efficient and reusable heterogeneous solid acid catalyst for the synthesis of biodiesel via esterification of oleic acid with methanol under high voltage conditions. Using an inexpensive and reusable catalyst, environmental benignity, excellent yields in short times, synthesis in atmospheric pressure and low temperature conditions are some of the important features of this protocol. In the final results were confirmed by GC.

Ageing is associated with a decline in both Nrf2 activity and DNA repair efficiency, leading to the accumulation of DNA damage and an increased risk of cancer. Understanding the mechanisms behind the increased level of damaged DNA during ageing is crucial for developing interventions to mitigate age-related cancer risk and improve overall health in older individuals. (Poly)phenols are plant-derived bioactive compounds that undergo metabolism into simpler phenolic catabolites following ingestion. While these compounds have been associated with various health benefits, further analysis of their bioavailable catabolites is necessary. To this end, four phenolic catabolites derived from colonic microbiota were investigated for their ability to reduce DNA damage in response to oxidative challenge and modulate the Nrf2-Antixoidant Response Element pathway. Normal and adenocarcinoma colonocyte cell lines (CCD 841 CoN, & HT29 respectively) were exposed to sub cytotoxic concentrations (>10 µM,) of hydroxylated (4-hydroxybenzoic acid, 3-(3’-hydroxyphenyl) propionic acid) and non-hydroxylated (benzoic acid or 3-phenylpropionic acid) phenolic acids. Using the COMET assay, each catabolite demonstrated significant (p<0.001) geno-protective activity, albeit with varying potency. They also significantly modulated expression of key genes in the Nrf2-ARE pathway, including Nrf2, Heme oxygenase-1 (HO-1), and NAD(P)H dehydrogenase quinone 1 (NQO1). Hydroxylation of the phenolic acids appeared to have a limited effect with respect to bioactivity. Overall, the colon derived phenolic metabolites, when assessed at physiologically relevant concentrations, reduced DNA damage in both normal and adenocarcinoma colonic cells in response to oxidative challenge, mediated – at least in part via upregulation of the Nrf2-ARE pathway.

Oxalate is a divalent organic anion that has implications across many biological and commercial processes. It is derived from plant sources, such as spinach, rhubarb, tea, cacao, nuts, and beans, and therefore is commonly found in raw or processed food products. Oxalate can also be made endogenously by humans and other mammals as a byproduct of hepatic enzymatic reactions. It is theorized that oxalate is useful for plants to store calcium and protect against herbivory. Clinically, oxalate is best known to be a major component of kidney stones, which commonly contain calcium oxalate crystals. Oxalate can induce an inflammatory response that decreases the immune system’s ability to remove renal crystals. When formulated with platinum as oxaliplatin (an anticancer drug), oxalate has been proposed to cause neurotoxicity and nerve pain. There are many sectors of industry that are hampered by oxalate, and some that depend on it. For example, calcium oxalate is troublesome in the pulp industry and the alumina industry as it deposits on machinery. On the other hand, oxalate is a common active component of rust removal and cleaning products. Due to its ubiquity, there is interest in developing efficient methods to quantify oxalate. Over the past four decades several diverse methods have been reported. These approaches include electrode-based detection, liquid chromatography or gas chromatography coupled with mass spectrometry, enzymatic degradation of oxalate with oxalate oxidase and detection of hydrogen peroxide as a product, and indicator displacement-based methods employing fluorescent or UV light-absorbing compounds. It has become clear that no single method will work best for every purpose. This review describes the strengths and limitations of each method, and may serve as a reference for investigators to decide which approach is most suitable for their work.

Hyaluronic acid, known also as hyaluronan, is the most abundant glycosaminoglycan in the extracellular matrix. It is produced by most of the cells in the human body, possibly contributing to various fundamental biological processes. This prompts interest in its therapeutic value. Hyaluronic acid (HA) has been used for various treatments owing to its broad range of properties in medical and dental field specially in periodontology. The review gives an overview on the effects of HA on fibroblasts, bone, wound healing, periodontal regeneration, aphthous ulcer/stomatitis and stem cells. Outcomes of including Hyaluronic acid in non-surgical periodontal therapy, drug delivery system and surgical procedures such as root coverage, papilla regeneration, root conditioning, intrabony defects, guided tissue regeneration are rather optimistic. HA has shown astounding potential in treating periimplantitis. Newer frontiers have to be explored to comprehend the other promising properties of HA. Keyword – Hyaluronic Acid, Periodontology.

DNA methylation is an epigenetic mechanism for gene expression modulation and can be used as a predictor of future disease risks. A prospective birth cohort study was performed to clarify the effects of neurotoxicants on child development, namely, the Tohoku Study of Child Development, in Japan. This study aimed to evaluate the association of prenatal exposure to five toxic metals—arsenic, cadmium, mercury, lead (Pb), antimony (Sb), and polychlorinated biphenyls (PCBs, N = 166)—with global DNA methylation in umbilical cord blood DNA. DNA methylation markers, 5-methyl-2’-deoxycytidine (mC) and 5-hydroxymethyl-2’-deoxycytidine (hmC), were determined using liquid chromatography-tandem mass spectrometry. The mC content in cord blood DNA was positively correlated with Pb and Sb levels (r = 0.442 and 0.288, respectively) but not with cord blood PCBs. We also observed significant positive correlations among Pb levels, maternal age, and hmC content (r = 0.159 and 0.243, respectively). The multiple regression analysis among the potential predictors demonstrated consistent positive associations between Pb and Sb levels and mC and hmC content. Our results suggest that global DNA methylation is a promising biomarker for prenatal exposure to Pb and Sb.

Supplier selection/replacement strategies and optimized purchasing policies play a key role in efficient supply chain management in today’s dynamic market. Here we study supplier replacement in a one-level assembly system (OLAS) producing one type of finished product. To assemble the product, we need to provide multi-type components, but assembly will be interrupted if any single component is missing, and incoming units will get hoarded until the missing component arrives. The assembly process can be interrupted by various sources of uncertainty, including delays in component deliveries. There is consequently a non-negligible risk that the assembly process may get stopped any moment. This brings inventory-related costs, which should be minimized. Here we consider discrete lead-time distributions to mimic industry-world reality. We present a model that takes into account not only optimal assignment of component order release dates but also replacement of a critical supplier. For a given unit, we model several alternative suppliers with alternative pricing and lead-time uncertainties, and we evaluate the impact on the total assembly system. For a more general case where several suppliers may be replaced, we propose a genetic algorithm.

Legumes are a diverse and important group of plants that play a vital role in agriculture, food security, and environmental sustainability. Rhizobia are symbiotic bacteria that form nitrogen-fixing nodules on legume roots, providing the plant with a valuable source of nitrogen. Phenolic acids are a group of secondary metabolites produced by plants that have a wide range of biological functions, including defense against pests and diseases, tolerance to abiotic stresses, and nutrient uptake. In the context of climate change and the imperative for sustainable agriculture, this study delves into the dynamic responses of legume species to varying light intensities and their intricate interactions with soil microorganisms. We investigated the impact of light intensity and rhizobial inoculation on the biomass, nitrate reductase, acid phosphatase, and production of phenolic acids in the roots of four legume species, Trifolium repens, Vicia sativa, Ornithopus compressus, and Coronilla juncea. Plants were grown under three light intensity regimes (low, medium, and high) and inoculated with either rhizobia or a non-inoculated control. The results highlights that shaded-light-adapted species, T. repens and V. sativa, increased root exudate production when exposed to high light intensity. This response aligns with their mining strategy, effectively allocating resources to optimize nutrient acquisition under varying conditions. In contrast, species hailing from well- illuminated environments, O. compressus and C. juncea, displayed distinct strategies by significantly increasing biomass under high irradiance, capitalizing on the available light and nutrients. The mining strategy of legumes emerged as a central theme, influencing biomass production, nitrogen dynamics, and enzymatic activities. The strong correlations between biomass and total nitrogen accumulation underscore the role of the mining strategy in efficient nutrient acquisition. Inoculated plants, which rely more on biological nitrogen fixation (BNF), exhibited lower δ15N values, indicative of a successful mining strategy to acquire and utilize atmospheric nitrogen. Enzymatic activities and phenolic acids exhibited significant interspecies variations, reflecting the adaptability of legumes to different light conditions. The findings of this study could be used to develop new strategies for improving legume stress tolerance, nutrient uptake capacity, and rhizosphere health.

We present synthetic experiments of lactic acid (LA) polycondensation to produce poly(lactic acid) (PLA), as well as kinetic modeling calculations that capture the polymer molecular weight increase with time, given the initial concentrations. Tin-octoate-catalyzed polycondensation of (D,L)- or L-lactic acid, was carried out in pre-dried toluene after azeotropic dehydration for 48-120 hours at 130-137 °C. The polymerization was optimized by varying lactic acid and catalyst concentrations as well as the temperature. Gel Permeation Chromatography was used to experimentally follow the evolution of molecular weights and the products were characterized by NMR, TGA, DSC and IR. Under optimal conditions, PLLA with weight-average molecular weight (Mw) of 161 kDa could be obtained. The rate equations that describe polycondensation kinetics were recast in a condensed form that allowed very fast numerical solution and calculation of the number-average molecular weight with time. Deviations with respect to the experiment were minimized in a least-squares fashion, to determine rate constants. The optimized kinetics parameters are shown to reproduce the experimental data accurately

Coffee is one of the most popular beverages in the world. Annual coffee consumption continues to increase, but at the same time, it generates a large amount of spent coffee grounds from the brewing process, that arises environmental problems. An appropriate solution to manage these spent coffee grounds becomes crucial. Our project aims to discuss the feasibility of utilizing the spent coffee ground to synthesize polylactic acid as a recycling application for spent coffee ground. This paper will discuss the properties and potential recycling applications of spent coffee grounds, the brief production process of polylactic acid, and the potential process for converting spent coffee ground to lactic acid. From our review, it is feasible to utilize spend coffee ground as the primary sources for lactic acid production by bacteria fermentation, and further produce bioplastics, polylactic acids by ring-opening polymerization. Possible ways to improve the yield and corresponding cost analysis are also discussed.

Plants are constantly exposed to a variety of different environmental stresses, including drought, salinity, and elevated temperatures. These stress cues are assumed to aggravate in the future driven by the global climate change scenario which we are currently experiencing. These stressors have largely detrimental effects on plant growth and development and, therefore, put global food security in jeopardy. For this reason, it is necessary to expand our understanding of the underlying mechanisms by which plants respond to abiotic stresses. Especially boosting our insight into the ways by which plants balance their growth and their defense programs appears to be of paramount importance, as this may lead to novel perspectives that can pave the way to increase agricultural productivity in a sustainable manner. In this review, our aim was to present a detailed overview of different factettes of the crosstalk between the antagonistic plant hormones abscisic acid (ABA) and auxin, two phytohormones that are the main drivers of plant stress responses, on the one hand, and plant growth, on the other.

Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

Tea and coffee are the most commonly used beverages throughout the world. Both decoctions are rich in small organic molecules such as phenolics/polyphenolics, purine alkaloids, many methylxanthines, substituted benzoic and cinnamic acids. Many of these molecules are physiologically chemopreventive and chemoprotective agents against many severe conditions such as cancer, Alzheimer, Parkinsonism, inflammation, sleep apnea, cardiovascular disorders, bradycardia, fatigue, muscular relaxation, and oxidative stress. Caffeine, a purine alkaloid, is a common metabolite of both tea and coffee aqueous decoctions and its concentration in tea/coffee depends on the fermentation process, preparation of the water extract and quality of tea leaves/coffee beans. A 250 ml of a coffee cup contains 100-150 mg caffeine while the same volume of strong tea contains 25-40 mg caffeine. The present paper presents the potential of caffeine as a potent chemopreventive agent that can be used for numerous physiological disorders.

In the last decades, cultivation of chia (Salvia hispanica L.) has expanded around the world and the seeds have become well known due to their rich composition in nutrients and bioactive compounds. The aim of this work was to evaluate the physical, chemical and nutritional profile of eight chia seeds grown in different Latin-American countries (Argentina, Bolivia, Chile, Ecuador, Mexico, Paraguay and Peru). The results showed that several nutritional parameters such as the protein content and amino acid profile, dietary fiber content, lipid content, mineral composition and phytate present in the seeds depend on the location they were grown in. Other parameters such as ash content, fatty acid profile or physical parameters were uniform across locations (except for color parameters). The results support the notion that nutritional characteristics of seeds are determined by the seed's origin, further analysis is needed to define the exact mechanisms that control the changes in the seeds nutritional properties.

Ecuador is the world's fifth largest cocoa producer, generating hundreds of annual tons of residues from this fruit. This research aims to value this residual (cocoa pod husk) by using it as raw material to obtain pectin, which is widely used in the food and pharmaceutical industries. For them, the extraction of three different organic acids with GRAS status (and therefore safe for their use), citric, malic and fumaric acids, were studied. In addition, two other factors, temperature (70-90°C) and extraction time (60-90 min), were explored in a central composite design of experiments. Under the conditions of the experiment, it was obtained that the best yields were reached for citric acid, malic acid and fumaric acid and for ~86 min of extraction time. The temperature did not show a significant influence on the yield. The pectins obtained under optimal conditions were characterised, showing their similarity with commercial pectin. However, the equivalent weight and the esterification degree of the pectin obtained with fumaric acid classify it as having a high equivalent weight and a low degree of esterification. It differs significantly from the other two acids, perhaps due to the limited solubility of fumaric acid.

The rise in prevalence of obesity in women of reproductive age in both developed and developing countries might propagate intergenerational cycles of detrimental effects on metabolic health, contributing to substantial economic burden on society. Placental lipid metabolism might be disrupted by maternal obesity, which possibly affects the life-long health of the offspring. Here, we investigated placental lipid metabolism and handling from women with pre-gestational obesity as a sole pregnancy complication and compared to placental responses of lean women. Open profile and targeted lipidomics were used to assess placental lipids and oxidized products of docosahexahenoic acid (DHA), neuroprostanes, and arachidonic acid (AA), isoprostanes. Placental fatty acid transporters FABP1, FABP3 and endothelial lipase protein were measured. Despite no signs of overall alterations in lipid content, increased contents of DHA, AA, DHA-derived neuroprostanes and AA-derived isoprostanes and decreased content of FABP1 protein were found in placentas from obese women. Multivariate analyses suggested that these oxidised fatty acids are associated with maternal and placental inflammation and also with birth weight. These results might shed light on the molecular mechanisms associated with altered fatty acid metabolism and lipid handling in maternal pre-gestational obesity, placing these oxidized fatty acids as novel mediators of placental function.

Thai basil is a renowned medicinal plant and a rich source of bioactive antioxidant compounds having several health benefits, with actions to prevent of cancer, diabetes and cardiovascular disease. Plant cell and tissue culture technologies can be routinely established as an important, sustainable and low-cost biomass source for the production of high-value phytochemicals. The current study aimed at developing an effective protocol for the production of Thai basil leaf derived callus cultures with sustainable and high production of biomass and antioxidants as an alternative of leaves production. MS basal medium with various concentrations of plant growth regulators (PGRs) compatible with nutraceutical applications (i.e., gibberellic acid (GA3) and 6-benzylaminopurine (BAP) either alone or in combination with naphthalene acetic acid (NAA)) were evaluated. Among all tested PGRs, the combination BAP:NAA (5 mg/L:1 mg/L) yield maximum biomass accumulation (fresh weight (FW): 190 g/L and dry weight (DW): 13.05 g/L) as well as enhanced phenolic (346.08 mg/L) production. HPLC quantification analysis indicated high productions of chicoric acid (35.77 mg/g DW) and rosmarinic acid (7.35 mg/g DW) under optimized callus culture conditions. Antioxidant potential was assessed using both in vitro cell free and in vivo cellular antioxidant assays. Maximum in vitro antioxidant activity DPPH (93.2 % of radical scavenging activity) and ABTS (1322 µM Trolox equivalent antioxidant capacity) was also observed for the extracts from callus cultures grown on optimal conditions. In vivo cellular antioxidant activity assay confirmed the effective protection against oxidative stress of the corresponding extract by the maximum inhibition of ROS and RNS production. Compared to commercial leaves, callus extracts showed higher production of chicoric acid and rosmarinic acid associated with higher antioxidant capacity. In addition, this biological system also has a large capacity for continuous biomass production, thus demonstrating its high potential for possible nutraceutical applications.

Lysophosphatidic acid (LPA) type 3 (LPA3) receptor mutants were generated in which the sites detected phosphorylated were substituted by non-phosphorylatable amino acids. Substitutions were made in the intracellular loop 3 (IL3 mutant), the carboxyl terminus (Ctail), and both domains (IL3/Ctail). The wild-type (WT) receptor and the mutants were expressed in T-REx HEK293 cells, and the consequences of the substitutions were analyzed employing different functional parameters. Agonist- and LPA-mediated receptor phosphorylation was diminished in the IL3 and Ctail mutants and essentially abolished in the IL3/Ctail mutant, indicating that the main sites were substituted and distributed in both domains. The WT and mutant receptors increased intracellular calcium and ERK 1/2 phosphorylation in response to LPA and PMA. An increase in baseline ERK phosphorylation was detected in the IL3/Ctail mutant. LPA and PMA-induced receptor interaction with β-arrestin 2 and LPA3 internalization were severely diminished in the mutants. Mutant-expressing cells also exhibit increased baseline proliferation and response to different stimuli, which were inhibited by the antagonist Ki16425, suggesting a role of LPA receptors in this process. Migration in response to different attractants was markedly increased in the Ctail mutant, which the Ki16425 antagonist also attenuated.

The host glycosylation mechanism synthesizes the carbohydrates of glycoproteins of viral envelopes. Due to the loss of the Cytidine Monophospho-N-Acetylneuraminic Acid Hydroxylase gene by some mammalian species, including humans (negative-CMAH), Neu5Gc is no longer synthesized. Uptake of Neu5Gc by negative-CMAH species, through the intake of food products derived from positive-CMAH mammals, leads to incorporating Neu5Gc-glycans in the glycocalyx (xenosialylation). Neu5Gc, being a Mammalian-associated Carbohydrate Antigen (MCA), acts as a non-self-antigen, inducing an inflammatory reaction (Xenosialitis), and triggering the production of circulating antiNeu5Gc antibodies to attack/remove all incorporated Neu5Gc. In the state of Xenosialitis, the virus-neutralizing antibodies produced by a heavily xenosialylated patient following exposure to viral infection (including SarsCoV2) or anti SarsCoV2 vaccination cross-react against all incorporated non-self Neu5Gc-MCA glycans due to their resemblance with viral envelope antigens synthesized by the host glycosylation mechanism. In addition, the circulating anti-XeSias antibodies determine the massive removal of the circulating neutralizing FC-xeno-contaminated antibodies by the serum, living only the hyper-inflammatory agalattosylated antiviral IgG antibodies. Therefore, we hypothesize that the combination of antibody cross-reaction against non-self Neu5Gc-MCA glycans and the massive removal of the xeno-contaminated newly formed neutralizing antibodies in favor of hyper reactive antibodies, could be the cause of the massive inflammatory reaction (cytokine storm, coagulopathies, neuropathies) observed in Covid 19 patients or after anti-SarsCoV2 vaccination. This analysis is an invitation to investigate the post-infectious and/or post-vaccination adverse phenomena in the light of xenosialization as a key to understanding the severe post viral and post vaccine complications, including SARS-CoV2 infection or related vaccination.

To study the fermentation process of biocatalyzing decanoic acid to synthesize trans-2-decenoic acid, this study was based on the engineering E.coli constructed in the laboratory in the early stage and studied the effect of seed liquid culture time, culture temperature, inoculum amount, induction temperature, dissolution effects of substrate solvent, metal ions, and substrate loading on the yield of trans-2-decenoic acid. Based on single-factor experimental optimization, the Box–Behnken design was used to conduct response surface testing using the substrate feeding concentration, inducer concentration, and MnCl2 concentration as response variables and trans-2-decenoic acid production as the response value. The optimal fermentation process was determined through experiments: seed culture time 20 h, culture temperature 37°C, inoculation amount 1%, induction temperature 30°C, substrate flow amount 0.15 g/L, inducer concentration 5.60 g/L, MnCl2 concentration was 0.10 mM. Under these conditions, the average production of trans-2-decenoic acid was 1.982 ± 0.110 g/L. Compared with the basic LB medium, the production of trans-2-decenoic acid increased by 1.042 g/L; compared with the previous period, the yield of trans-2-decenoic acid studied increased by 1.501 ± 0.110 g/L, which provides a reliable basis for further research on the fermentation process of biocatalytic decanoic acid synthesis of trans-2-decenoic acid.

Pentadecanoic acid (C15:0) is an essential odd-chain saturated fatty acid with broad activities relevant to protecting cardiometabolic, immune, and liver health. C15:0 activates AMPK and inhibits mTOR, both of which are core components of the human longevity pathway. To assess the potential for C15:0 to enhance processes associated with longevity and healthspan, we used human cell-based molecular phenotyping assays to compare C15:0 with three longevity-enhancing candidates: acarbose, metformin, and rapamycin. C15:0 (n=36 activities in 10 of 12 cell systems) and rapamycin (n=32 activities in 12 of 12 systems) had the most clinically relevant, dose-dependent activities. At their optimal doses, C15:0 (17 µM) and rapamycin (9 µM) shared 24 activities across 10 cell systems, including anti-inflammatory (e.g., lowered MCP-1, TNFɑ, IL-10, IL-17A/F), antifibrotic, and anticancer activities, which are further supported by previously published in vitro and in vivo studies. Paired with prior demonstrated abilities for C15:0 to target longevity pathways, hallmarks of aging, aging rate biomarkers, and core components of type 2 diabetes, heart disease, cancer, and nonalcoholic fatty liver disease, our results support C15:0 as an essential nutrient with activities equivalent to, or surpassing, leading longevity-enhancing candidate compounds.

This study examines the behavior of stearic acid (SA) and 12-hydroxystearic acid (12-HSA) aqueous mixtures as a function of temperature and 12-HSA/SA molar ratio (R). Whatever R, the system exhibits a morphological transition at a given threshold temperature, from multilamellar self-assemblies at low temperature towards small micelles at high temperature, as shown by a combination of transmittance measurements, Wide Angle X-ray diffraction (WAXS), small angle neutron scattering (SANS) and differential scanning calorimetry (DSC) experiments. Such transition originates from the melting of the crystallized fatty acids within the lamellar phase. The precise determination of the threshold temperature, which ranges between 20°C and 50°C depending on R, allows for the construction of the whole phase diagram of the system as a function of R. At high temperature the micelles that are formed are oblate for pure SA solutions (R = 0) and prolate for pure 12-HSA solution (R = 1). In the case of mixtures, there is a progressive continuous transition from oblate to prolate shape when increasing R, with micelles that are almost purely spherical for R = 0.33.

Ludwigia octovalvis (Jacq.) P.H. Raven is widely used in traditional medicine for different illnesses included diabetes and hypertension. However, its impact on lipotoxicity and metabolic syndrome in vivo has not been addressed. Therefore, the aim of this study was to evaluate the effects of this plant on the metabolic syndrome parameters in a C57BL6J mouse hypercaloric diet model. L. octovalvis hydroalcoholic extract and its ethyl acetate fraction (25 mg/kg/day) were used for sub-chronic assessment (10 weeks). Also four subfractions (25 mg/kg) were evaluated in the postprandial triglyceridemia test in healthy C57BL6J mice. The hydroalcoholic extract and ethyl acetate fraction significantly decreased body weight gain (-6.9 g and -1.5 g), fasting glycemia (-46.1 and -31.2 mg/dL), systolic (-26.0 and -22.5mmHg) and diastolic (-8.1 and 16.2 mmHg) blood pressure, free fatty acid concentration (-13.8 and -8.0 μg/mL) and insulin-resistance (measured by TyG index, -0.207 and -0.18) compared to the negative control. Postprandial triglyceridemia test showed that the effects in the sub-chronic model are due, at least in part, to improvement in this parameter. L. octovalvis treatments, particularly the hydroalcoholic extract, improve MS alterations and decrease free fatty acid concentration. These effects are possibly due to high contents of corilagin and ellagic acid.

We describe the behavior of mixtures of stearic acid (SA) and its hydroxylated counterpart 12-hydroxystearic acid (12-HSA) in aqueous mixtures at room temperature, as function of the 12-HSA/(fatty acid) mole ratio R. The morphologies of the self-assembled aggregates are obtained by a multi-structural approach that combines confocal and cryo-TEM microscopies with Small-Angle Neutron Scattering (SANS) and Wide-Angle X-Rays Scattering (WAXS) measurements, coupled with rheology measurements. Fatty acids are solubilized by an excess of ethanolamine counterions, so that their heads are negatively charged. The behavior is driven by the competition between mixing entropy and enthalpic effects. A clear trend towards partitioning between the two types of fatty acids is observed, presumably driven by the favorable formation of a H-bond network between hydroxyl OH function on the 12th carbon. For all R, the self-assembled structures are locally lamellar, with bilayers composed of crystallized and strongly interdigitated fatty acids. At high R, multi-lamellar tubes are formed, similarly as for pure aqueous solutions of 12-HSA. The doping by a low amount of SA molecules only slightly modify the dimensions of the tubes (radius and length), and slightly decreases the bilayers rigidity. The solutions have a gel-like behavior originating from entanglements between tubes and show a yield stress. At intermediate R, a partial local partitioning occurs between the two types of fatty acids. The tubes coexist in solution with helical ribbons. The two structures possibly merge to form very long snaky objects with straight and curved parts. The rigidity of the bilayers and the rheological behavior of the solutions are very similar to those of the high R case. At low R, local partitioning also occurs, and the architecture of the self-assemblies associates the two morphologies of the pure fatty acids systems, respectively 2-D planar bilayers for SA and the tubes describe above for the 12-HSA molecules: they are facetted objects with planar domains enriched in SA molecules, capped with curved domains enriched in 12-HSA molecules. The rigidity of the bilayers is strongly increased, as well their storage modulus, compared to systems with larger R. The solutions remain however viscous fluids in this regime of low R.