Natural laterite fixed-bed column intercalated with activated carbon prepared from Balanites ae-gyptiaca (BA-AC) was used for As(III) removal from an aqueous solution. Investigations were carried out to solve the problem of column clogging which appears during water percolation through the column. Experimental tests were conducted to evaluate the hydraulic conductivity and the effects of various parameters such as grain size, bed height, and initial As(III) concentra-tion. The breakthrough increased from 15 to 85 h with the increase of the bed height from 20 to 40 cm, and decreased from 247 to 32 h with the increase of initial As(III) concentration from 0.5 to 2 mg/L. The permeability data showed that the fixed-bed column filled with laterites layers intercalated with activated carbon performs much better than the non-intercalated adsorbent col-umn. The Bohart-Adams model showed that increasing the bed height induced a decrease in kAB and N0 values. The critical bed depths determined using the bed depth service time (BDST) mod-el for As(III) removal were 15.23 and 7.98 cm for 1 and 20% breakthrough, respectively. The re-sults showed that the new low-cost filtration system, based on laterite layers alternated with BA-AC layers, could be used for the treatment of arsenic-contaminated water.

The Ni-laterite deposit at the San Felipe plateau, located 30 km northwest of Camagüey, in cen-tral Cuba, is the best example of a clay-type deposit in the Caribbean region. San Felipe resulted from weathering of mantle peridotites of the Cretaceous Camagüey ophiolites. In this study, a geochemical and mineralogical characterization of two profiles (83 and 84) from the San Felipe deposit has been performed by XRF, ICP-MS, quantitative XRPD, oriented aggregate mount XRD, SEM, FE-SEM and EMPA. Core 83 with a length of 23 m, and drilled in the central part of the plateau, presents a notable concentration of cryptocrystalline quartz fragments and a rather poor content in NiO, averaging 0.87% wt. Core 84, which is 12 m long, and drilled at the border of the plateau, lacks silica fragments and presents a higher NiO content, averaging 1.79 %wt. The smectite structural formulae reveal that they evolve from trioctahedral to dioctahedral towards the top of the laterite profiles. Quantitative XRD analyses indicate that smectite is a dominant Ni bearing phase, accompanied by serpentine and minor chlorite. Serpentine, as smectite, is en-riched in the less soluble elements Fe3+, Al and Ni towards the top of the profiles. Core 83 seems to have been affected by collapses, replenishments, whereas core 84 may have remained undis-turbed.

Nickel is widely used in industrial processes and plays a crucial role in many applications. However, most of the nickel resource mainly exists as nickel oxide in laterite nickel ore with complex composition, resulting in difficulty in upgrading the nickel content using physical separation methods. In this study, high-grade ferronickel concentrates were obtained through a carbothermal reduction and magnetic separation using laterite nickel ore and anthracite as raw materials. The effects of different types of additives (CaF2, Na2SO4 and H3BO3), carbon ratio (nc/no in metal oxides) and grinding time on the recoveries and grades of ferronickel concentrates were experimentally investigated, along with the microstructure and chemical composition of the products. CaF2 was proved to be the primary active additive in the aggregation and growth of the ferronickel particles, and the improvement of the grade of the product. Under the optimal conditions of CaF2 addition of 12 wt.%, carbon ratio of 1.4, and grinding time of 240 s, high-grade magnetically separable ferronickel concentrate with nickel grade 8.93 wt.% and iron grade 63.96 wt.% was successfully prepared. This work presents a practical method for the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore, contributing to the development of strategies for the sustainable extraction and utilization of nickel resources.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.