Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

This paper presents a new scientific contribution on the two-dimensional (2-D) subdomain technique in polar coordinates taking into account the finite relative permeability of the ferromagnetic material. The constant relative permeability corresponds to linear part of the nonlinear B(H) curve. As in conventional technique, the method of separation of variables and the Fourier’s series are used for the resolution of magnetostatic Maxwell’s equations in each region. Although, the general solutions of magnetic field in the subdomains and boundary conditions (BCs) between regions are different in the conventional and proposed method. In this later, the magnetic field solution in each subdomain is a superposition of two magnetic quantities in the two directions (i.e., r- and Q-axis) and the BCs between two regions are also in both directions. For example, the scientific contribution has been applied to an air- or iron-cored coil supplied by a constant current. The distribution of local quantities (i.e., the magnetic vector potential and flux density) has been validated by a corresponding 2-D finite-element analysis (FEA). The obtained semi-analytical results are in very good agreement with those of numerical method.

Two billion people worldwide suffer from anemia with reproductive-age women being disproportionately affected. Iron plays a crucial role in cellular function and impacts cognition, physical function, and quality of life. Iron deficiency (ID) and iron deficiency anemia (IDA) are associated with adverse effects on pregnancy and fetal development. Oral iron supplementation has been the standard treatment for IDA for decades often producing sub-optimal outcomes. Many babies are still being born with ID and suffer adverse sequelae due to inadequate iron levels in the mothers. Is it time to consider broad scale-up of parenteral iron as a new standard of care?

Iron deficiency (ID) is by far the most common nutritional disorder in developing and developed countries. When left untreated, ID leads to anemia. Although the usual recommended treatment for iron deficiency anemia (IDA) is oral iron therapy with countless products, such therapy necessitates administration for >3-6 months with questionable patient compliance since most oral iron products have an unpleasant metallic aftertaste and cause intestinal side effects. In addition, in certain gastrointestinal conditions, such as inflammatory bowel diseases or untreated gluten-sensitive enteropathy, oral iron therapy is contraindicated or unsuccessful. Intravenous iron is considered safe in adults, where adverse events are mild and easily managed. The experience with parenteral iron in children is much more limited and many pediatricians appear reluctant to use it because of uncorroborated fears of serious anaphylactic reactions. In the current article, we thoroughly review the available pediatric literature on the use of all commercially available parenteral iron products except ferumoxytol, which was recently removed from the market. We conclude that parenteral iron appears to be safe in children, it works faster than oral iron and the newer third-generation products allow replacement of the total iron deficit at a single setting.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

Introduction: In the recent years alternate day dosing has been recommended in iron deficieny treatment. The aim of this study is to compare the efficacy and side effects of oral iron treatments given daily 1x1, alternate day 1x1 and 2x1 alternate day dosing in iron deficieny anemia patients. Methods: A total of 52 patients with a diagnosis of iron deficiency anemia with serum ferritin level of 25 µg/L or less were included in this retrospective study. Statistical analyzes were done with SPSS V.25. Results: The patients included in our study were between the ages of 18-51. All of the patients included in the study were female. A statistically significant increase was found between 0-14 days(p<0.001), 14-28 days(p<0.001) and 0-28 days(p<0.001) hemoglobin values in all patients. There was no statistically significant difference between 0-14 days (p=0.397) and 0-28 days(p=0.310) ferritin values in all patients. A statistically significant difference was found between 14-28 days(p<0.001) ferritin values. When the rate of change of hemoglobin and ferritin values between the groups was compared and no statistically significant difference was observed between the groups. The rate of change of ferritin values for 14-28 days was significant (p=0.012). There was no significant difference in the frequency of symptoms in the 14th day and 28th day controls for each group (p>0.05). The incidence of metallic taste and bloating symptoms was found to be statistically significant in the third control in the group with 2x1 drug use alternate day (p=0.094). Discussion: The only difference in efficacy was observed in ferritin values between 14th and 28th days. The increase in ferritin values was higher in the group that used 1x1 oral iron every day. However, since no difference was observed between the groups in terms of ferritin and hemoglobin values on days 0 and 28, all three groups were considered equally efficient. Side effects were mainly gastrointestinal side effects. Since the group that received 2x1 oral treatment alternate day had a statistically significantly higher rate of side effects, the patients’ treatment tolerance will be lower compared to the other groups. In conlusion, there is no difference in efficacy and side effects between the patient groups receiving 1x1 daily and 1x1 alternate day oral iron therapy, so 1x1 use alternate day is the most appropriate treatment method for oral iron therapy in terms of patient tolerance, adherence to treatment and pharmacoeconomics.

β-thalassemia, a congenital genetic hematological disorder characterized by decreased or absence of β-globin chains, leads to decrease in levels of Hemoglobin A. The affected individuals can be categorized into two cohorts based on transfusion dependency: transfusion dependent thalassemia (TDT) and non-transfusion dependent thalassemia (NTDT). Remarkably, despite the primary pathology lying in β-globin chain depletion, β-thalassemia exhibits an intriguing association with iron overload. Iron metabolism, a tightly regulated physiological process, reveals a complex interplay in these patients. Over time, both cohorts of β-thalassemic individuals develop iron overload, albeit through distinct mechanisms. Addressing the diverse complications arising due to iron overload in β-thalassemic patients, the utilization of iron chelators has gained a lot of significance. With varying efficacies, routes of administration, and modes of action, different iron chelators offer unique benefits to patients. In the Indian context, three commercialized iron chelators have emerged, showcasing a high adherence rate to the iron chelator-based treatment regimens among β-thalassemic individuals. In this review, we explore the intriguing connection between β-thalassemia and iron overload, shedding light on the intricate mechanisms at play. We delve into the intricacies of iron metabolism, unveiling the distinct pathways leading to iron accumulation in these patients. Additionally, we critically evaluate the therapeutic efficacy of different iron chelators, emphasizing their respective advantages in managing iron overload complications. Through this comprehensive analysis, we aim to deepen our understanding of β-thalassemia and iron overload, paving the way for optimized treatment strategies. Ultimately, our findings provide valuable insights into improving the care and outcomes of individuals affected by β-thalassemia.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

Antarctic krill protein-iron complex and peptide-iron complex were obtained to investigate their iron bioavailability, expression of iron-regulated genes, and in vivo antioxidant capacity. Results indicated that Antarctic krill peptide-iron complex increased significantly the hemoglobin (Hb), serum iron (SI) and iron content in the liver and spleen in iron-deficiency anemia (IDA) mice (P < 0.05) compared with those of Antarctic krill protein-iron complex. Despite the gene expressions of divalent metal transporter 1(DMT1), transferrin (Tf) and transferrin receptor (TfR) could be better regulated by both Antarctic krill peptide-iron complex and protein-iron complex, the relative iron bioavailability of the Antarctic krill peptide-iron complex group (152.53±21.05%) was significantly higher than that of the protein-iron complex group (112.75±9.60%) (P<0.05). Moreover, Antarctic krill peptide-iron complex could enhance the antioxidant enzyme activities of superoxidase dismutase (SOD) and glutathione peroxidase (GSH-Px), reduce the malondialdehyde (MDA) level in IDA mice compared with the protein-iron complex, reducing the cell damage caused by IDA. Therefore, these results demonstrated that Antarctic krill peptide-iron complex could be used as a highly efficient and multifunctional iron supplement.

Background: Iron chelation medications (desferoxamine, desferasirox, desferiprone) are used to manage iron overload. These medications are partially excreted via the kidneys, desferoxamine and desferiprone excretes primarily in the urine, and desferasirox had about 8% excreted in the urine. Their use in severe kidney disease and dialysis patients is caution as “avoided” concerning adverse effects; however, there are reports safe use. This manuscript reviews the literature in this population. Data Sources: Pubmed: desferasirox, deferiprone, deferoxamine, kidney disease, ESKD, Dialysis. Case reports and case series that described experiences with using iron chelation medications in ESKD patients are included. Data also gathered from reading-related sources. Results: This is a review of desferoxamine, desferasirox, and deferiprone use in kidney disease from 1976 to the present time. Table 1 provides a summary of findings. These are mostly reports and brief descriptions of the experiences used in severe kidney disease and dialysis, but lack of randomized control trials and small number of participants. Conclusions: Iron chelation medications are important for treating iron overload but concerns with adverse effects. Due to limited medications available to treat iron overload in patients with severe kidney disease, their safe use has been reporting in the literature. This is an area that warrants further research.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

(1) Background: Ferric carboxymaltose (FCM) is an intravenous (IV) high-dose iron that is effective in the treatment of iron deficiency anemia. This study was to determine if preoperative IV FCM administration could improve recovery from postoperative anemia in patients undergoing revision total joint arthroplasty. (2) Methods: This prospective randomized controlled study analyzed 82 patients undergoing revision total joint arthroplasty during a single hospitalization. Patients in the iron group (n = 41) were administered 1000 mg of IV FCM two weeks preoperatively, while those in the control group (n = 41) were not. Moreover, patients with anemia defined as a preoperative suboptimal Hb concentration &lt;13.0 g/dl were compared according to IV FCM administration. The absolute Hb levels and changes in Hb levels, iron profiles, transfusion rate, and EuroQOL 5-dimension (EQ-5D) scores were compared. (3) Results: There were no significant differences in recovery of Hb levels at each timepoint between the two groups; however, the changes in Hb levels from baseline to four weeks postoperatively showed marginally significant differences favoring the iron group (p = 0.052). However, for preoperatively anemic patients, the change in hemoglobin (Hb) levels between baseline and four weeks postoperatively was significantly better in the iron group than in the control group (iron group [n = 26], −0.3 ± 0.7 g/dL vs. control group [n = 27], −0.9 ± 0.8 g/dL; p = 0.040), although the absolute Hb levels, transfusion rates, and patient quality of life were comparable (all p &gt; 0.05). The iron group showed improved iron metabolite levels including serum ferritin and transferrin saturation four weeks postoperatively, and no adverse events associated with IV FCM administration occurred in either group. (4) Conclusions: Preoperative IV FCM in anemic individuals undergoing revision joint arthroplasty was effective in accelerating recovery from surgery-related anemia by improving Hb levels without any adverse events, despite similar actual Hb levels between the groups. Our findings are clinically relevant and can facilitate determination of the suitability of IV FCM as a safe and reliable protocol for iron supplementation for anemia correction.

In pigs, iron deficiency anemia (IDA) is the most prevalent deficiency disorder during the early postnatal period frequently developing into a critical illness. Meanwhile, in humans, only low-birth-weight infants, including premature infants are especially susceptible to developing IDA. In both human and pig neonates, the initial cause of IDA is low birth iron stores. In piglets this shortage of stored iron results mainly from genetic selection over the past few decades for large litter size and high birth weight. In consequence, pregnant sows cannot provide sufficient amount of iron to the increasing number of developing fetuses. Supplementation with iron is a common practice for the treatment of IDA in piglets. For decades, the preferred procedure for delivering iron supplements during early life stages has been through the intramuscular injection of large amount of iron dextran. However, this relatively simple therapy, which in general, efficiently corrects IDA, may generate toxic effects, and by inducing hepcidin expression, may decrease bioavailability of supplemental iron. New iron supplements are considered now with the aim to combine improvement of hematological status, blunting hepcidin expression, and minimizing toxicity of the administered iron. We propose that iron-deficient piglets constitute a convenient animal model for performing pre-clinical studies with iron supplements.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

Inflammation is an underlying problem for many disease states and has been implicated in iron deficiency (ID). This study aimed to determine whether iron status is improved by epigallocate-chin-3-gallate (EGCG) through reducing inflammation. Thirty-two male Sprague-Dawley rats were randomly divided into four groups (n = 8 each): positive controls, negative controls, lipo-polysaccharide (LPS, 0.5 mg/kg body weight), and LPS + EGCG (LPS plus 600 mg EGCG/kg diet). Iron status, hepcidin, C - reactive protein (CRP), serum amyloid A (SAA), and interleukin-6 (IL-6) were measured. There were no differences in treatment groups compared with control in CRP, hepcidin, and liver iron concentrations. Serum iron concentrations were significantly lower in the LPS (p=0.02) and the LPS+EGCG (p=0.01) than in the positive control group. Compared to the positive control group, spleen iron concentrations were significantly lower in the negative con-trol (p<0.001) but not with both LPS groups. SAA concentrations were significantly lower in LPS + EGCG group compared to LPS alone group. IL-6 concentrations were significantly higher in LPS+EGCG (p= 0.004) than in any of the three groups. EGCG reduced SAA concentrations but did not affect hepcidin or improve serum iron concentration or other iron markers.

Dietary iron assimilation is critical for health and essential to prevent iron deficient states and related comorbidities, such as anemia. The bioavailability of iron is limited, while its absorption and metabolism are tightly controlled to keep body iron stores within a relatively narrow range. Genetic inactivation of the iron hormone hepcidin causes hereditary hemochromatosis, an endocrine disorder of iron overload characterized by chronic hyperabsorption of dietary iron, with deleterious clinical complications if untreated. The impact of high dietary iron intake and elevated body iron stores in the general population is not well understood. Herein, we summarize epidemiological data suggesting that high intake of heme iron, which is abundant in meat products, poses a risk factor for metabolic syndrome pathologies, cardiovascular diseases, and some cancers. We discuss clinical relevance and potential limitations of data from cohort studies, as well as the need to establish causality and elucidate molecular mechanisms.

Myelodysplastic syndromes and myeloproliferative neoplasms both represent hematologic diseases associated with bone marrow failure often resulting in anemia. For those patients, transfusion of red blood cell (RBC) units is essential, but results in iron overload (IOL) that may affect various organ functions. Therefore, iron chelation therapy plays a major role in anemic patients, not only because it reduces IOL, but also because it may improve hematopoietic function by increasing hemoglobin or diminishing requirement of RBC transfusions. To assess the utility, efficacy and safety of the different iron chelation medication approved in Germany as well as to examine the effect of chelation on hematopoietic insufficiency, a prospective, multicenter, non-interventional study named EXCALIBUR was designed. In total, 502 patients from 106 German hospitals and medical practices were enrolled. A large proportion of patients switched from deferasirox dispersible tablet to deferasirox film-coated tablet, mainly due to more convenient application which was reflected in the treatment satisfaction questionnaire for medication scores. Iron chelation was effective in lowering serum ferritin levels, with the observed adverse drug reactions being in line with the known safety profile. Hematologic response occurred in a few patients, comparable to other studies that examined hematologic improvement in patients with MDS.

The study, conducted at the Department of Medicine, Maulana Azad Medical College and associated Lok Nayak Hospital, aimed to investigate the prevalence of iron deficiency anaemia among anaemic overweight and obese individuals. Fifty participants were included after screening and consent, undergoing socio-demographic assessment, clinical evaluation, and laboratory investigations. Middle to old-aged individuals predominated (Mean ± SD: 54.54 ± 11.32 years), with females comprising 62%. All subjects were obese (mean BMI: 37.27 ± 5.71 kg/m²), with common comorbidities including hypertension (68%), diabetes (36%), and obstructive sleep apnea-hypopnea syndrome (32%). Nutritional deficiencies, particularly iron deficiency, were prevalent, affecting 62% of subjects, with 48% having iron deficiency alone. Anemia of chronic illness was observed in 38%. Laboratory parameters showed low hemoglobin (8.53 ± 1.23 g/dL), MCV (78.75 ± 10.13 fL), and elevated ESR (20.56 ± 21.47 mm/hour) and CRP levels (4.71 ± 3.32 mg/dL), indicating inflammation. Correlation analyses revealed negative associations between BMI and serum iron/ferritin and positive associations with serum hepcidin. The study underscores the significance of addressing nutritional deficiencies and monitoring iron status in obese populations, suggesting potential associations between obesity and iron metabolism. Further research is needed to explore these relationships for clinical management implications.

Oligodendroglioma (OG) is a brain tumor that contributes to < 1% of brain tumor diagnoses in the pediatric population. Unfortunately, pediatric OG remains without definitive molecular characteristics to aid in diagnosis, and little is known about the tumor microenvironment. Tumor cells' metabolism and proliferation rate are generally higher than healthy cells, so their iron demand is also significantly increased. This consideration underlines the great importance of iron for tumor development and progression. In this context, this study aims to evaluate the effect of iron in a cellular in vitro model of human oligodendroglioma brain tumor. Cell morphology, the effect of siderotic medium on cell growth, iron uptake, and the expression of iron metabolism-related genes were evaluated by optic microscopy, ICP-MS, confocal microscopy, and RealTime PCR, respectively. This study underlines the great importance of iron for tumor development and progression, but also the possibility of reducing the available iron concentration to determine an antiproliferative effect on OGs. Therefore, every attempt can be promising to defeat the OGs for which there are currently no long-term curative therapies.

Baía de Todos os Santos is the second largest bay in Brazil and is home to important ecosystems, including estuarine systems and mangroves. However, studies on the seasonal variability of its soil properties and composition are still scarce. For this study, soil and leaf samples were seasonally collected from mangrove forests at four sites (Cacha Prego, Ponta Grossa, Ilha de Maré, and Pitinga), which are representative of different environmental conditions within the BTS. Soil physicochemical properties, soil composition and partition of Fe forms were determined, and analysis of minerals by Scanning Electron Microscope, was performed on soil samples. Isotopic ratios (δ13C, δ15N) were also determined on soil and leaf samples. Soils showed significant spatial and temporal changes affecting both their properties (pH, Eh) and their composition (TOC, pyrite and Fe oxyhydroxide contents). Clear spatial changes were observed in redox potential, significantly affecting the concentrations of the different geochemical forms of Fe, particularly the concentrations of crystalline oxyhydroxydes and pyrite in one of the studied sites. In three of the study sites, pyrite crystals showed clear evidence of degradation associated with sandy soils. Finally, δ13C and N/C ratios in soils seem to suggest a mixed origin of organic matter.

Beta-thalassemia major (β-TM) is a severe form of thalassemia caused by mutations in the β-globin gene, resulting in partial or complete deficiency of β-globin chains. This deficiency results in oxidative stress, dyserythropoiesis, and chronic anemia. Cytokine dependent hematopoietic cell linker (CLNK) belongs to the adaptor protein family and has the capacity to interact with multiple signaling proteins thereby modulating signal transduction. The aim of the present study was to examine CLNK in sera of β-TM patients and examine its association with iron overload biomarkers. Sixty β-TM patients, aged 3–12 years old and undergoing blood transfusions, and 30 healthy control children were recruited and CLNK, ferritin and iron status parameters were measured. The results showed a significant increase (p < 0.001) in serum CLNK levels in β-TM patients as compared with normal controls. The increased levels of CLNK were significantly associated with increased ferritin levels. Increased CLNK levels in β-TM may be explained by reciprocal effects between immune signaling and immature erythrocytes, which, release soluble receptors and signaling molecules, including CLNK, in the blood.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

A review of desiccant dehumidification technologies for improving air-quality has been presented, especially focusing on alternatives for air conditioning systems for minimizing the Sick Building Syndrome. The principles and types of desiccant wheels, as well as the existing selection software for these types of equipment, were reviewed and comparatively evaluated. The study focuses on the Brazilian context, therefore, information about air condition systems and laws of this country were evaluated. Possible applications of desiccant wheels are also analyzed, such as their integration into cooling cycles and the sensible heat wheel. Finally, several commercial desiccant wheel selection software were evaluated, which are useful in many situations. Nevertheless, it was evidenced that the available softwares are not capable of performing an operation analysis for only a specific period. Therefore, it is essential to create computational tools to select desiccant wheels, considering the data from the different Brazilian regions for a year.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

Many drastic actions are taken by cocaine users for the sake of experiencing high dopamine levels, which depends on iron for its synthesis. Dopamine depletion and iron deficiency are also involved in the symptoms of restless leg syndrome (RLS). The intersecting biochemical pathways of cocaine use, iron deficiency, and RLS have not been adequately investigated. This case report reveals the successful treatment of a patient with these conditions. A 63-year-old male with a history of cocaine use disorder, insomnia, and RLS sought emergency care for suicidality. Upon admission, he was also found to be iron-deficient. He revealed that his RLS worsened when he attempted to abstain from cocaine. He also used alcohol to sustain the effects of cocaine when the cost of cocaine was too high. During hospitalization, his mood, cravings, and RLS were resolved with adjunctive iron supplementation as well as 300 mg of Wellbutrin. If iron-deficient, replenishment of adequate dopaminergic receptor density and function via supplementation may play an essential role in the prevention of cocaine use and cessation of cocaine withdrawal. Further research is warranted to validate these findings and understand the implications of iron supplementation in addiction medicine.

Iron deficiency anemia (IDA) is a world health problem for humans and other mammals; affecting critical stages of development. Pigs have been used as an experimental model for the study and prevention of anemia because of physiological and metabolic similarities with humans. Iron dextran particles (IDP) are used for intramuscular (IM) IDA treatments in pigs, but are insufficient for prevention of anemia due to quick metabolization. Therefore, the objective of this study was to develop chitosan thermosensitive hydrogels (CTH) formulations and to study their potential as a mammalian parenteral iron dextran supplementation strategy. CTH were loaded with IDP at increasing iron concentrations (0.1, 0.2 and 0.4 g of theorical iron/g of chitosan) and characterized as an IM iron supplement. All the CTH-IDP formulations were thermosensitive and can be injected IM at ~4 °C, with a significant rise in viscosity between 25-37 °C. IDP content was physically trapped in the chitosan hydrophobic gel at 37 °C, without evidence of chemical bonding. We conclude that CTHs are a promising strategy for IM delivery strategy of IDP, and these results may be useful for future iron supplementation studies in pigs, humans and other mammals.

Neurodegeneration with brain iron accumulation (NBIA) is a group of rare neurogenetic dis-orders frequently associated with iron accumulation in the basal nuclei of the brain. Among NBIA subtypes, β -propeller protein-associated neurodegeneration (BPAN) is associated with mutations in the autophagy gene WDR45. The aim of this study was to demonstrate autophagic defects and secondary pathological con-sequences in cellular models derived from two patient harboring WDR45 mutations. Both protein and mRNA expression levels of WDR45 were decreased in patient-derived fibro-blasts. In addition, the increase of LC3B upon treatments with autophagy inducers or inhibitors was lower in mutant cells compared to control cells, suggesting decreased autophagosome formation and impaired autophagic flux. Transmission electron microscopy (TEM) analysis showed mitochondrial vacuolization associated with accumulation of lipofuscin-like aggregates containing undegraded material. Autophagy dysregulation was also associated with iron ac-cumulation and lipid peroxidation. In addition, mutant fibroblasts showed altered mitochon-drial bioenergetics. Antioxidants such as pantothenate, vitamin E and α-lipoic prevented lipid peroxidation and iron accumulation. However, antioxidants were not able to correct the ex-pression levels of WDR45 neither the autophagy defect nor cell bioenergetics. Our study demonstrated that WDR45 mutations in BPAN cellular models impaired autophagy, iron metabolism and cell bioenergetics. Antioxidant partially improved cell physiopathology, however autophagy and cell bioenergetics remained affected.

Wheat (Triticum aestivum L.) being a staple food crop is an important nutritional source providing protein and minerals. It is important to fortify staple cereals like wheat with essential minerals to overcome the problems associated with malnutrition. The experiment was designed to evaluate the status of 11 micronutrients including grain iron (GFe) and zinc (GZn) in 62 wheat cultivars released between 1911 and 2016 in Pakistan. Field trials were conducted over two years and GFe and GZn were quantified by both inductively coupled plasma optical emission spectroscopy (ICP-OES) and energy dispersive X-ray fluorescence spectrophotometer (EDXRF). The GZn ranged from 18.4 to 40.8 mg/kg by ED-XRF and 23.7 to 38.8 mg/kg by ICP-OES. Similarly, GFe ranged from 24.8 to 44.1 mg/kg by ICP-OES and 26.8 to 36.6 mg/kg by EDEXR. The coefficient of correlation was higher for GZn (r=0.90), compared to GFe (r=0.68). Modern cultivars like Zincol-16 and AAS-2011 showed higher GFe and GZn along with improved yield components. Old wheat cultivars WL-711, C-518 and Pothowar-70 released before 1970 also exhibited higher value of GFe and GZn, however their agronomic performance was poor. Multivariate analysis using ten micronutrients (Al, Ca, Cu, K, Mg, Mn, Na and P) along with agronomic traits, and genome-wide SNP markers identified the potential cultivar with improved yield, biofortification trait and wider genetic diversity. Genetic gain analysis identified significant increase in grain yield (0.4% year-1), while there was negative gain for GFe (-0.11% year-1) and GZn (-0.15% year-1) over the span of 100 years. The Green Revolution Rht-B1 and Rht-D1 genes had strong association with plant height, and grain yield (GY), while semi-dwarfing alleles had negative effect on GFe and GZn contents. This study provided a valuable insight into biofortification status of wheat cultivars deployed historically in Pakistan and is a valuable source to initiate a breeding strategy for simultaneous improvement in wheat phenology and biofortification.

Iron (Fe) is a trace element that plays essential roles in various biological processes such as DNA synthesis and repair, as well as cellular energy production, or oxygen transport, and it is currently widely recognized that iron homeostasis is dysregulated in many cancers. Indeed, several iron homeostasis proteins may be responsible for malignant tumor initiation, proliferation, and for metastatic spread of tumors. A large number of studies demonstrated the potential clinical value of turning these deregulated proteins as prognostic and/or predictive biomarkers of malignancy and /or response to anticancer treatments. Additionally, the iron addiction of cancer cells and the importance of iron in ferroptosis cell death signaling pathways prompted the development of therapeutic strategies against advanced stage or resistant cancers. In this review, we selected relevant and promising studies in the field of iron metabolism in cancer research and clinical oncology. Besides, we discuss some co-existing discrepant findings. We will also present and discuss the latest lines of research related to targeting iron, or its regulatory pathways, as potential promising anti-cancer strategies for human therapy. Iron chelators, such as deferoxamine or iron-oxide based nanoparticles, which are already tested in clinical trials, alone or in combination with chemotherapy will also be reported.

Background: Essential hypertension is a major public health associated with increase pressure on the vascular walls and red blood cells (RBCs). In the present work, osmotic fragility (OF) of RBCs was reexamined in the means of its correlation with two risk factor; iron status and lipid profile. Experimental: OF, iron status parameters, and lipid profile components were measured in 60 patients and compared with the results of 30 controls. Results: The results showed a significant increase in all iron indices of hypertensive patients in comparing with healthy control group except TIBC, UIBC, and transferrin concentrations, which decrease in these patients in comparing with control group. Serum TGs, total cholesterol, VLDLc, and LDLc were increased while there is no significant in serum HDLc in patients to comparing with control group. There is no significant change in OF between patients and controls where p=0.173. The iron status parameters and lipid profile components were dependent on sex and smoking state. Hemoglobin and PCV were correlated significantly with total cholesterol and LDLc. Transferrin saturation showed a positive correlation with cholesterol, LDLc, and TGs, but negatively correlated with HDL_c. No significant correlation between all the measured parameters and OF in HT patients. There is a significant correlation between serum ferritin and systolic BP and between Hb and systolic BP. Conclusion: No significant effect on the OF in HT patients. HT patients have elevated level of iron parameters in comparing with controls. OD has no correlation with iron status parameters or with lipid profile components.

Iron deficiency in the fetal and neonatal period (perinatal iron deficiency) bodes poorly to neuro-development. Given its common occurrence and the negative impact on brain development, a screening and treatment strategy that is focused on optimizing brain development in perinatal iron deficiency is necessary. Pediatric societies currently recommend a universal iron supple-mentation strategy for full-term and preterm infants that does not consider individual variation in the body iron status and could lead to under-treatment or over-treatment. Moreover, the focus is on hematological normalcy and not optimal brain development. Several serum iron indices and hematological parameters in the perinatal period are associated with risk of abnormal neurodevelopment, suggesting their potential use as biomarkers for screening and monitoring treatment in infants at risk for perinatal iron deficiency. A biomarker-based screening and treatment strategy that is focused on optimizing brain development will likely improve outcome in perinatal iron deficiency.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

The study of co-fusion was one of the essential topics in the history of metallurgy in China. Simulation experiments had been an essential concept in the study of the co-fusion steelmaking process. This paper mainly studied the simulation experiments of co-fusion from two aspects: the replication of co-fusion swords by three different methods, and the micro-analysis of the co-fusion samples. The experimental results indicated that several co-fusion swords could be made by different processes, but the carbon content and surface hardness were quite different. During repeated forging welded, the microstructure of the samples transformed from laminated to homogenized, finally the steel with a uniform carbon content was obtained. It was challenging to find the characteristics of co-fusion from the homogenized samples. The results prompted people to rethink the microstructure characteristics of ancient co-fusion artifacts.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The coronavirus disease (COVID-19) pandemic caused by spreading rapidly a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has imposed a unique situation for the humanity. Sao Paulo has reported 124,105 confirmed cases of COVID-19 and 5,623 deaths up to June 14th, being considered the epicenter of the pandemic in Brazil and in South America. Due to the measures for social distancing, there was a drop in the air pollution concentration in Sao Paulo. Starting on March 16th, 2020, we broke 90 days of social distancing into 13 weeks and compared to an equivalent period in 2019. We investigated the air quality improvement during the quarantine period and compared the associated avoided deaths to COVID-19 burden deaths. Nitrogen dioxide (NO₂) was the best indicator of air quality in the analyzed weeks, since its reduction reached 58 %. Our study showed that the 5,623 deaths occurred during the analyzed weeks of quarantine represents an economic health loss of US$ 10.5 billion. In opposite, we observed a significant air quality improvement due to pollutants concentrations’ reductions during the analyzed weeks. Considering PM₁₀, PM_2.5 and NO₂, the decrease of concentration levels respectively avoided 78, 337 and 387 premature deaths and prevented up to US$ 1.5 billion on health costs. These results highlight the importance of continuing to enforce existing air pollution regulations and measures to protect human health both during and after COVID-19 pandemic.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

The aim of the study was to investigate the association between maternal dietary iron intake during pregnancy and the gut microbiota characteristics of both the mother and neonate in a well-characterized cohort. A total of 95 mother-neonate dyads were included in our study, with basic information collected through questionnaires. A semi-quantitative Food Frequency Questionnaire (FFQ) was used to assess maternal dietary intake during pregnancy, and maternal dietary iron intake was categorized into &lt;20 mg/d and ≥20 mg/d groups. Fecal samples were collected from the mother in the third trimester and the neonate, allowing for assessment of the community profile and diversity of gut microbiota via 16S rRNA amplicon sequencing. Then, a comparison between different maternal dietary iron intake groups was conducted, adjusting for delivery mode (VD, vaginal delivery; CS, cesarean section) and other potential confounding factors. No significant differences in community profile and diversity were observed for the maternal gut microbiota in different dietary iron intake groups. In neonate fecal samples, the Shannon (P = 0.044) and Simpson (P = 0.010) diversity indices of the gut microbiota were higher in the maternal dietary iron intake ≥20 mg/d group, while Simpson diversity presented the same tendency in vaginal delivery (P = 0.041) after stratification. The relative abundance of the core genus Bifidobacterium showed a significant difference between groups (4.69 [1.19–12.77] vs. 13.98 [3.44–27.28]; P = 0.044). The abundance of Lactobacillus was different in the ≥20 mg/d group under both delivery modes (VD: beta = 2.9, w = 4.13; CS: beta = 2.77, w = 3.8). Our findings suggest that adequate dietary iron intake during pregnancy may promote beneficial bacterial colonization and increase the biodiversity of the neonate gut microbiota.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

Keywords: iron deficiency anemia; IDA; anemia; knowledge; awareness.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

INTRODUCTION. The most common cause of eating non-food items (pica) is specific deficiencies of minerals, such as iron. This study aimed to assess the relationship between Pica and Iron deficiency anemia among pregnant women. METHODS. The study was conducted in the out-patient department, antenatal Clinic at East Jeddah Hospital from July to September 2020. Design: A quantitative descriptive correlation design. Sample size: A total of 400 pregnant women, included anemic pregnant women, ≥ 18 years old, with singleton fetus and iron deficiency anemia. RESULTS. The mean age was 32.2 ± 6.6, half of the participants reported food cravings. Ice was the main item in pica followed by clay and chalk. Two-thirds had pica, more than half during the 1st trimester. There is a statistically significant relationship between pica and the history of a family member, parity, and gravidity at (P< 0,001, P <0,001, P <0,005) respectively. Hb and hematocrit in relation to pica reflected a statistically significant relationship (P< 0,001) and (P< 0,001), respectively. The symptoms attributed to iron deficiency were significantly associated with pica (P< 0,006). CONCLUSION. The pica and iron deficiency anemia had a significant association with pregnant women in EJH. RECOMMENDATION. The follow-up visits should integrate the food behavior inquiry to check if the pica existing with anemic or non-anemic pregnant women. Also, increase the awareness among midwives-nurses about the prevalence of pica and iron deficiency anemia among pregnant women.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

Beta thalassemia major (β-TM) disorder characterized by the lack, or severe reduction in the production of hemoglobin β-globin chains. The standard protocol for the management of β-TM is blood transfusion and iron chelation therapy to reduce the iron overload state. The present study aimed to investigate the relationships between two iron regulatory hormones, hepcidin (HEPC) and erythroferrone (ERFE) levels and iron status parameters (ISPs) in Iraqi patients with β-TM. ISPs and hormones were measured in sixty patients and compared with thirty healthy controls. The results indicated significant changes in different iron status parameters, while ferritin (FRT) with the ~11 fold increase showed the most change. Significant reduction in HEPC and increase in ERFE levels were detected in patients as compared to the control group, while no direct correlation was identified with the other measured ISPs. Receiver operating characteristic (ROC) analysis showed that the z-score of the composite of ERFE+FRT has a full diagnostic ability for β-TM. In conclusion, our finding indicated the correlation between different ISPs, FRT as the leading predictor of iron overload and tow main iron regulatory hormones.

Pearl millet is an important food crop in the arid and semi-arid tropical regions of Africa and Asia. These regions are home to millions of poor smallholder’s households living in harsh agro ecology and reported higher prevalence of malnutrition. Such poor households have few options in terms of food crops, besides the limited markets. Indeed, pearl millet is one of the food crops they continue to grow for their food and nutritional security. Pearl millet is important sources of dietary carbohydrates, energy, protein, and important minerals such as calcium, iron and zinc. Considering inherent high nutritional values and climate resilient nature (drought and heat), demand for pearl millet as food, beside valued for its Stover as a source of livestock fodder, is projected to grow strongly in Asia (India) and Africa (West and Central Africa). Iron (cause anemia) and zinc (cause stunting) deficiencies are widespread and serious public health problems worldwide, including India and Africa. Biofortification is a cost-effective and sustainable agricultural strategy to address this problem. Research on pearl millet has shown that large genetic variability (30-140 mg/kg Fe and 20-90 mg/kg Zn) available in this crop can be effectively utilized to develop high-yielding cultivars with high iron and zinc densities. Both Open –pollinated varieties (Dhanshakti and Chakti) and hybrids (ICMH 1202, ICMH 1203 and ICMH 1301) of pearl millet with high grain yield (>3.5 tons/ha in hybrids) and high levels of iron (70-75 mg/kg) and zinc (35-40 mg/kg) densities have been developed and released. Currently, India growing >70,000 ha of biofortified pearl millet, besides more pipeline hybrids and varieties are under various stage of testing at the national (India) and international (west Africa) trials for possible release. Genomic tools will be an integral part of breeding program particularly for nutritional traits to use diagnostic markers and genomic selection. Clinical studies showed that 200g grains from biofortified cultivar would provide bioavailable Fe to meet full recommended daily allowance (RDA) in children, adult men and 80% of the RDA in women. Till today, no markets to promote biofortified cultivars/grains/products as no incentive price and such products aims to address food and nutritional security challenges simultaneously. The demand is likely to increase only after investment and integration into modern public distribution system, nutritional intervention schemes, private seed and food companies with strong mainstreaming nutritional policies. In the non-traditional regions, this will contribute to livestock and poultry feed industry as spill-over benefits to improve nutrition.

Nuclear receptor coactivator 4 (NCOA4) is a selective cargo receptor that mediates the autophagic degradation of ferritin (“ferritinophagy”), the cytosolic iron storage complex. NCOA4-mediated ferritinophagy maintains intracellular iron homeostasis by facilitating ferritin iron storage or release according to demand. Ferritinophagy is involved in iron-dependent physiological processes such as erythropoiesis, where NCOA4 mediates ferritin iron release for mitochondrial heme synthesis. Recently, ferritinophagy has been shown to regulate ferroptosis, a newly described form of iron-dependent cell death mediated by excess lipid peroxidation. Dysregulation of iron metabolism and ferroptosis have been described in neurodegeneration, cancer, and infection, but little is known about the role of ferritinophagy in the pathogenesis of these diseases. Here, we will review the biochemical regulation of NCOA4, its contribution to physiological processes and its role in disease. Finally, we will discuss the potential of activating or inhibiting ferritinophagy and ferroptosis for therapeutic purposes.

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

Abstract: This article explores the intricate relationship between environmental degradation, specifically air pollution, and economic growth in the Sultanate of Oman spanning the period from 1990 to 2022. We employ cointegration and vector error correction models to uncover both short- and long-term dynamics in the association between air pollution and economic growth. Fur-thermore, Granger causality analysis is utilized to investigate the causal links between these crucial variables. This data encompasses factors related to environmental quality and various control variables. The empirical results unveil a sustained long-term cointegration connection between the variables. Additionally, our findings highlight a statistically significant positive impact of economic growth and energy consumption on CO2 emissions. Furthermore, the short-term analysis reveals an annual adjustment of approximately 14.1% in N2O emissions dis-equilibrium. The Granger causality study indicates unidirectional causal relationships involving N2O emissions, economic growth, and CO2 emissions. The implications of these findings for Oman's policy landscape are substantial. To effectively reduce greenhouse gas emissions, it is imperative for Oman to establish robust climate change policies. Additionally, the government can play a pivotal role in encouraging and endorsing the use of renewable energy sources, such as green hydrogen, as a promising alternative to traditional oil and gas resources.

As the haze engulfed the Delhi NCR after Diwali there is a panic in public about its causes and consequences. Here are some facts and figures to know the truth behind the scene. Temperature fell down from 24’C on October 31 to 21’C on November 2 as recorded at UPPCB station at sector-125, Noida which is adjacent to Delhi a very strategic location and can be considered as reference point for Delhi-NCR. The details of the study conducted is given below.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Livestock production systems generate nuisance odor and gaseous emissions affecting local communities and regional air quality. Also, there are concerns about the occupational health and safety of farm workers. Proven mitigation technologies that are consistent with the socio-economic challenges of animal farming are needed. We have been scaling up the photocatalytic treatment of emissions from lab-scale, aiming at farm-scale readiness. In this paper, we present the design, testing, and commissioning of a mobile laboratory for on-farm research and demonstration of performance in real farm conditions. The mobile lab is capable of treating up to 1.2 m3·s-1 of air with TiO2-based photocatalysis and adjustable UV-A dose based on LED lamps. We summarize the main technical requirements, constraints, approach, and performance metrics for the mobile laboratory, such as the effectiveness (measured as the percent reduction) and cost of photocatalytic treatment of air. The commissioning of all systems with standard gases resulted in ~9% and 34% reduction of NH3 and butan-1-ol, respectively. We demonstrated that as the percent reduction of standard gases increased with increased light intensity and treatment time. These results show that the mobile laboratory was ready for on-farm deployment and evaluating the effectiveness of UV treatment.

Background and objectives: sickle cell disease is the most common hemoglobinopathy in the world. It is considered to be a real public health problem. Sickle cell patients are subjected to several factors causing inflammation such as iron metabolism. The study aimed to look for inflammation in children with sickle cell disease in Cameroon, identify the factors associated with inflammation, and raise the consequences for the patient including the iron profile and the profile of the hemogram. Materials and methods: We conducted an analytical cross-sectional study for 03 months. The sickle cell disease patients coming and/or followed at the Hematology Department of the Regional Hospital of Bafoussam and the Central Hospital of Yaoundé have been recruited. The exploration of inflammation was made by determining CRP, IL6, and ferritin concentrations. The hematological parameters and iron profile were evaluated using standard methods. Statistical analysis of the data was performed; Univariate and multivariate logistic regression analyses allowed to identification of factors associated with inflammation in patients, using the statistical tool R version 4.1.1.. The proportions were compared with the chi-square test when the expected numbers were greater than 5 and the Fisher test when not. Results: The frequency of inflammation in the population was 42.3%. Hyperferritinemia was significantly greater (p<0.001) in patients with inflammation compared to the non-inflammatory patients (96.8% and 76.7% respectively). Patients with inflammation showed a significant elevation of iron parameters (p<0.05). In addition, ferritin and IL6 elevation were associated with inflammation during sickle cell disease respectively (Or = 4.96; 95% CI [1.15-36.42]; p=0.056) and (Or =6.23; 95% CI [1.43-45.96]; p=0.030). Conclusions: The elevated iron in plasma is an effect of inflammation in sickle cell patients. Hence the need of controlling inflammation and iron in the latter is necessary.

We have successfully synthesized a series of Bi doped BaFe2As2 high quality single crystals for the first time. The x-ray diffraction (XRD) patterns show an expansion of lattice parameter c with Bi doping, indicating a negative pressure effect. By investigating the resistivity, a Fermi liquid (FL) to non-Fermi liquid (NFL) crossover is observed from normal state to antiferromagnetic order state, accompanied by three superconducting transitions labeled as SC I, SC II and SC III which are supposed to be induced from three superconducting realms with various Bi concentration. Thus, the NFL behavior is proposed to be closely related with the presence of superconductivity. The magnetic susceptibility measurements further speculates that the SC I and SC III phases should be filamentary superconductivity while the SC II be a possible bulk superconductivity with TC 7 K.

Organometallic drug development is still in its early stage, but recent studies show that organometallics having iron as the central atom have the possibility of becoming good drug candidates because iron is an important micro-nutrient, and it is compatible with many biological systems, including the human body. Being an eco-friendly Lewis acid, iron can accept the lone pair of electrons from imino(sp2)-nitrogen, and the resultant iron-imine complexes with iron as a central atom have the possibility of interacting with several proteins and enzymes in humans. Iron-imine complexes have demonstrated significant potential as anticancer, bactericidal, fungicidal, and other medicinal activities in recent years. This article systematically discusses major synthetic methods and pharmacological potentials of iron-imine complexes having in vitro activity to significantly affect clinical performance from 2016 to date. In a nutshell, this manuscript offers a simplistic view of iron complexes in medicinal inorganic chemistry: for instance, iron is presented as an "eco-friendly non-toxic" metal (as opposed to platinum) that will lead to non-toxic pharmaceuticals. The abundant literature on iron chelators shows that many iron complexes, particularly if redox-active in cells, can be quite cytotoxic, which can be beneficial for future targeted therapies. While we made every effort to include all the related papers, any omission is purely unintentional.

Ferroptosis is a recent form of non-apoptotic cell death, which occurs due to imbalance of iron homeostasis (iron overload). Oxidative stress due to the impairment of the antioxidant system is a major pathophysiology during ferroptosis, which eventually results in lipid peroxidation. The cellular and physiological biomarker of ferroptotic cell death includes major alteration in the glutathione peroxidase 4 (GPX4) antioxidant system and lipid peroxidation induced loss of plasma membrane integrity. This review elaborates the mechanism of oxidative stress which triggers ferroptosis.

In this presented case, a 77 years old woman suffering from ongoing knee pain underwent a bone scan using 99mTc-hydroxydiphosphonate (HDP) in suspicious for bone infection. An incidental finding from this scan revealed diffuse cardiac uptake, necessitating further diagnostic procedures to exclude the possibility of cardiac amyloidosis. In the subsequent 99mTc-3,3-diphosphono-1,2-propanodicarboxylic acid (DPD) scan and SPECT images, no perceptible cardiac uptake was observed at all. Upon retrospective review of the patient’s medical records, she had received 1000mg of ferric carboxymaltose for iron-deficient anemia, the day before the 99mTc-HDP bone scan. Therefore, it is assumed that the diffuse and temporary cardiac activity was due to the transient iron overload. We present and share this bone scan images in order to avoid possible future misinterpretation of cardiac amyloidosis.

This contribution was devoted to unveil the strain rate sensitivity (SRS) of G18NiCrMo3-6 cast steel in tension/compression asymmetry. For that purpose, detailed mechanical characterization tests were conducted providing a process window covering quasi-static and medium strain rate regimes (0.001, 0.1, 10 [ s¯¹]) in tension and compression states. By means of this experimental ef-fort, the SRS of the material could be extracted by a function of strain and strain rate which ena-bling to create a mathematical expression to easily be implemented as a state variable for constitu-tive material modeling. Finally, a pressure and rate dependent constitutive material model on the basis of Cocks'89 yield locus definition was created by a subroutine (UMAT) file and the material parameters were verified with respect to the experimental data. The UMAT file also takes into account the tension/compression asymmetry in yielding to handle the effect of porous media plas-ticity concept. The predictions of the proposed material model are quite in line with the experi-mental outputs.

Background. Intravenous iron therapy is used in treatment of anemia in uremic pa-tients. In patients treated with peritoneal dialysis iv. infused iron diffuses into the peritoneal cavity and may cause injury to the mesothelial cell. Methods. We studied effect of Iron Isomaltoside (IIS) in presence of NF-κβ inhibitor dehydroxymethyepoxyquinmicin (DHMEQ) on function of the peritoneal mesothelial cells. Experiments were performed on human peritoneal mesothelial cells in in vitro culture ex-posed to IIS 15 ug/dL ± DHMEQ 1 ug/mL. Intracellular oxidative stress, secretory activity and collagen synthesis in the cells were studied. Results. IIS induced oxidative stress in the mesothelial cells and that effect was weaker in presence of DHMEQ (-52%,p<0.001). In cells exposed to IIS increased expression of genes for IL6 (+74%,p<0.001), PAI-1 (+43%, p<0.01) and TGFβ (+53%,p<0.001) was observed and reduced for tPA (-36%,p<0.01). In presence of IIS increased secretion of IL6 (+56%, p<0.001), TGFβ (+49%,p<0.001) and PAI-1 (+51%, p<0.001) was observed whereas secretion of tPA was reduced (-25%, p0.001). DHMEQ reduced changes in genes and secre-tory activity caused by IIS. In presence of IIS synthesis of collagen in mesothelial cells was increased (+45%,p<0.001) and that effect was weaker (-25% vs. IIS, p<0001) when simulta-neously DHMEQ was used. Discussion. IIS induces proinflammatory changes in mesothelial cells, deteriorates their fibrinolytic activity and stimulates synthesis of collagen. All these effects are reduced when simultaneously NF-κβ inhibitor – DHMEQ is used.

Nitriding has long been used to engineer the surfaces of engineering steels to improve their surface and subsurface properties. The role of the surface compound layer (’-Fe4N and/or -Fe2-3N) in improving the tribological and corrosion resistant properties of nitrided steels has been established. However, there have been very few studies on the response of the compound layer to tribocorrosion in corrosive environments. In this work, the tribocorrosion behaviour of a 5 m thick ’-Fe4N nitride layer produced on mild steel (MS) by plasma nitriding has been studied in a NaCl containing solution under various electrochemical conditions. The results show that at a cathodic potential, where mechanical wear is predominant, the total material removal (TMR) from the ’-Fe4N layer is 37% smaller than that from the untreated MS, and at open circuit potential, TMR from the layer is 35% smaller than that from the untreated MS, while at an anodic potential, the ’-Fe4N layer can reduce TMR from mild steel by 87%. The beneficial effect of the ’-Fe4N nitride layer in improving the tribocorrosion behaviour of mild steel is derived from its high hardness and good corrosion resistance in the test solution and its ability to resist both mechanical wear and chemical wear.

Fe[C5H5N]2[N(CN)2]2 (1) was synthesized from a reaction of stoichiometric amounts of NaN(CN)2 and FeCl2·4 H2O in a methanol/pyridine solution. Single-crystal and powder diffraction show that 1 crystallizes in the monoclinic space group I2/m (no. 12), different from Mn[C5H5N]2[N(CN)2]2 (P21/c, no. 14) due to tilted pyridine rings, with a = 7.453(7) Å, b = 13.167(13) Å, c = 8.522(6) Å, β = 114.98(6)° and Z = 2. ATR-IR, AAS, and CHN measurements confirm the presence of dicyanamide and pyridine. Thermogravimetric analysis shows that π-stacking interactions of the pyridine rings play an important role in structural stabilization. Based on DFT-optimized structures, a chemical bonding analysis was performed using a local-orbital framework by projection from a plane-wave basis. The resulting bond orders and atomic charges are in good agreement with the expectations based on the structure analysis. SQUID magnetic susceptibility measurements show a high-spin state FeII compound with predominantly antiferromagnetic exchange interactions at lower temperatures.

Abstract: (1) Background: Sentinel lymph node biopsy assumes importance in the search for metastases, especially in patients with malignant breast disease. Our study approaches the new techniques to prevent complications such as possible postoperative seroma formation, pain or hypoesthesia of the axillary cord and medial arm surface, as well as motor deficits in a preventive manner to avoid disabling outcomes and presents initial data from its experience with the sentinel lymph node biopsy technique. (2) Methods: There are mainly two radioactive tracer detection techniques and a new technique using a radiotracer called Sentimag-magtrace. The positive lymph node is located and removed to perform histologic analysis. In our study, we evaluate 100 patients who underwent breast cancer surgery (3) Results: our experience allowed us to calculate the identification rate with the different methods of sentinel lymph nodes by radioactive tracer 88.9 % vs magnetic tracer technology (Sentimag) 89.5%. (4) Conclusions: Thus, this technique avoids radiation exposure for both patients and health care providers, as well as reducing costs and time.

Many ecosystems are being severely degraded, leading the United Nations to deem 2021-2030 as the Decade on Ecosystem Restoration. To be successful, this effort requires robust monitoring tools to assess land reclamation practices. Our study aimed to evaluate the quality of recovery efforts in mined areas by developing a Recovery Quality Index (RQI) based on soil and vegetation indicators. Using the heavily mined Iron Quadrangle region of Brazil as an example, we selected four local, undisturbed reference areas as restoration goals: Atlantic Forest (AF); ferruginous rupestrian grassland with dense vegetation (FRGD); ferruginous rupestrian grassland with sparse vegetation (FRGS); and quartzite rupestrian grassland (QRG). We also selected four areas that were directly or indirectly affected by mining, including an environmental compensation area set aside 5 years prior to the study (COMP-5), two sterile piles that had undergone recovery for 15 and 20 years (SP-20 and SP-15), and a cave area with 15 years of recovery (CAVE-15). The four recovery areas were grouped together with each individual reference area (making four combinations of sites), and measurements of 2 vegetation parameters and 34 soil attributes were used in a Principal Component Analysis (PCA) for each grouping. We determined the RQI for each group by summing weighted PCA scores for responsive indicators. Vegetative parameters had the lowest RQI weights in all four groups. Soil physical indicators tended to be the most important, except in AF, where chemical indicators were most relevant. RQI values were also lowest when AF was used as the reference, showing that the forest was a unique ecosystem, and the CAVE-15 site had lower RQI scores than the other restored sites, indicating the high degree of disturbance that occurred in that low-lying area. The SP-20 site tended to have higher RQI values than the SP-15, and similar values to the less disturbed COMP-5 areas, potentially indicating greater recovery of native soil properties during the longer recovery period. This RQI-based approach has excellent potential for robust assessment of the recovery of areas degraded by mining and can support decision-making during monitoring.

Several observations have shown that patients with polycythemia have iron deficiency. Our objectives were to report the prevalence of iron deficiency, to evaluate the diagnostic performance of serum ferritin in polycythemia vera and to describe the mechanisms of this association. This is a retrospective descriptive and analytical study carried out in the internal medicine department of the Henri Mondor Hospital, Aurillac, France. The study involved 114 patients with polycythemia, followed in the department from January 1, 2010 to December 31, 2021. To evaluate the diagnostic performance, the JAK2 mutation was considered as the gold standard of diagnosis. Thirty-three patients had polycythemia vera and 76 patients had secondary polycythemia. The mean age of the patients was 61.79 years (±15.44) with a sex ratio of 4.43. The overall prevalence of iron deficiency was 21.05%. The prevalence was 53% in polycythemia vera group and 1.32% in secondary polycythemia group. The risk of iron deficiency was high in polycythemia vera (OR=115; 95% CI [14.4-918.2], p<0.000). The sensitivity and specificity of serum ferritin were 52.63% and 100% respectively. Assessment of iron deficiency should be part of the initial evaluation of polycythemia. The presence of iron deficiency is specific for polycythemia vera.

Iron is the most abundant micronutrient in plant mitochondria and it has a crucial role in biochemical reactions involving electron transfer. It has been described in Oryza sativa that Mitochondrial Iron Transporter (MIT) is an essential gene and that knockdown mutant rice plants have a decreased amount of iron in mitochondria, strongly suggesting that OsMIT is involved in mitochondrial iron uptake. In Arabidopsis thaliana, two genes encode MIT homologues. In this study, we analyzed different AtMIT1 and AtMIT2 mutant alleles, confirming that individually AtMIT1 nor AtMIT2 genes are essential. When we generated crosses between Atmit1 and Atmit2 alleles we were able to isolate homozygous double mutant plants. Interestingly, homozygous double mutant plants were obtained only when mutant alleles of Atmit2 with the T-DNA insertion in the intron region were used for crossings, and in these cases a correctly spliced AtMIT2 mRNA was generated, although at a low level. Atmit1 Atmit2 double homozygous mutant plants, which were knockout for AtMIT1 and knockdown for AtMIT2, were grown and chacterised in iron sufficient conditions. Pleiotropic developmental defects were observed including abnormal seeds, increased number of cotyledons, slow growth rate, pinoid stems, defects in flower structures and reduced seed set. We observed a possible phenomenon of T-DNA suppression in the next generation of Atmit1 Atmit2 double homozygous mutant plants, correlating with an increased splicing of the AtMIT2 intron containing the T-DNA. Molecular analysis of gene expression markers for mitochondrial and oxidative stress showed that Atmit1 Atmit2 double homozygous mutant plants express a degree of mitochondrial perturbation. A RNA-Seq study was performed and we could identify more than 760 genes differentially expressed in Atmit1 Atmit2, including genes involved in iron transport, coumarin metabolism, and hormones metabolism, transport and signaling. Our data suggest that some of the phenotypes observed in Atmit1 Atmit2 double homozygous mutant plants are mediated by defects in auxin homeostasis.

This study is follow-up of the steel shot transformation under the influence of environmental factors research (Lisin et al., 2022) and is the initial stage of investigating the iron behavior in soils during steel shot corrosion under a number of factors: the metallic lead in soils, atmospheric precipitation, excess organic matter. The results obtained show that corrosion of steel ammunition is a continuous process, including the formation of a poorly soluble rust crust on the surface of the steel and the mineralization of the metal until it is destroyed. As a result, the metal transformed into rust form, is a constant source of iron ions and dispersed rust particles migrating in soil waters and accumulating in soils. In addition, the aggregation of corrosion products of steel ammunition is the cause of a change in physical and mechanical properties of soils, which leads to a violation of the air and water migration regime of soils and an increase in surface runoff from the territories of shooting activity. The highest environmental risks are observed when steel ammunition is used on shooting areas where metallic lead intensifies steel shot corrosion rate, while the deposited steel shot activates the deterioration of previously encapsulated metal and — if steel and lead ammunition are used at the same time — slows down the encapsulation of newly deposited metallic lead, which catalyses the accumulation and migration of lead in environmental components.

Abstract: COVID-19 in 2020 brought challenges to the Brazilian public health system with an emerging virus with respiratory contagion called SARS-CoV-2. There are few studies in Brazil and in some countries, on the increased incidence of certain viral respiratory infections, includ-ing H1N1 and coronavirus and their association with low levels of vitamin D, zinc and iron. The aim of this study was to demonstrate that the deficit of vitamin D, zinc and iron has an impact on the infectious process of patients with COVID-19 and to establish new forms of prevention for the worsening of COVID-19 in the human body. Data were collected from medical records and test results from patients being followed up during the treatment period for COVID-19. Patients with low blood levels of vitamin D, zinc and iron during the treatment period of COVID-19 had a higher percentage of worsening and complications requiring hospitalization in intensive care beds. The ingestion of vitamin D, zinc and iron in the treatment period of patients with COVID-19 in addition to being an immunological protector against SARS-CoV-2 and alleviating the process of worsening the disease can also act as a biomarker in cases of this disease.

Chronic diseases are characterised by cell’s autophagy and proteins disarrangement resulting in sarcopenia, hypoalbuminemia and hypo-haemoglobinaemia. Hypo-haemoglobinaemia couses worse prognosis independentely of the principal disease. Currently, the cornerstone of therapy of anaemia is iron supplementation, with or without erythropoietin for the stimulation of hematopoiesis. However, treatment strategies should incorporate the addition of heme, the principal biochemical constituent of haemoglobin. Heme synthesis follows a complex biochemical pathway. The limiting step of heme synthesis is D-ALA availability which, for its synthesis, requires Glycine and Succinil-CoA. Consequently, treatment of anaemia should not be based only on iron availability, but also on the availability of the molecules fundamental for heme synthesis. Therefore, an adequate clinical therapeutic strategy should integrate the standard iron infusion and the supply of essential amino acids and vitamins involved in the heme synthesis. We report preliminary data in selected elderly anaemic patients with congestive heart failure (CHF) and catabolic disarrangement, who, in addition to standard iron therapy, received personalized therapy with essential-AAs and vitamins involved in the maintenance of heme. Notably, such individualized therapy resulted in a significant increase in the serum concentration of haemoglobin after 30 days of treatment compared to standard iron therapy.

Streptococcus suis is a zoonotic pathogen causing serious infections in both swine and humans. Although metals are essential for life, excess amounts of metals they are toxic to bacteria. when accumulated in excess amounts. Except for zinc, Transcriptome-level data of the mechanisms for resistance to metal-induced toxicity in S. suis are available for no metals other than zinc. have not been investigated from the transcriptome level in S. suis. Herein, we explored the transcriptome-level changes of in S. suis in response to ferrous iron and cobalt toxicity by RNA sequencing. Many A lot of genes were differentially expressed in the presence of excess ferrous iron and cobalt. Most of the genes in response to cobalt toxicity showed the same expression trends as those were expressed in the same trend in response to ferrous iron toxicity. qRT-PCR analysis of the selected genes confirmed the accuracy of RNA sequencing results. Bioinformatics analysis of the differentially expressed genes indicated that ferrous iron and cobalt have similar impacts effects on the cellular processes of S. suis. Treatment with ferrous Ferrous iron treatment resulted in down-regulation of several oxidative stress tolerance-related genes involved in oxidative stress tolerance and up-regulation of the genes in an amino acid ABC transporter operon. Expression of the several genes in the arginine deiminase system was down-regulated in the presence of after ferrous iron and cobalt treatment. Collectively, our results suggested that S. suis alters the expression of a lot of multiple genes to respond to ferrous iron and cobalt toxicity.

The evolution of metals micro/nano-structure upon severe plastic deformation (SPD) is still far to be theoretically explained, while experimental datasets are persistently growing for several decades. Major problem associated with understanding of SPD is related to a fact that the latter is a synergetic product of several competing physical effects which alter the material micro/nano-structure. In attempt to find deformational boundaries, where predominantly one mechanism determines the micro/nano-structure, in this paper we propose a continuous piecewise model for the analysis of experiments on material hardness vs strain of SPD processed materials. The novelty of this approach lies in its ability to find, as free-fitting parameters, the strain breakpoints which separate different micro/nano-structure modes generated upon SPD process. The model is applied to analyse experimental data for polycrystalline samples of pure iron and two distinctive strain breakpoints are revealed with good accuracies. This finding is in a good agreement with our earlier results on TEM microscopy studies on pure iron polycrystals after SPD treatment.

The current study investigated the impacts of light quality and different levels of fertility on mineral nutrient concentrations in shoot and root tissues of Chinese kale (Brassica oleracea var. alboglabra). ‘Green Lance’ Chinese kale were grown under: 1) fluorescent/incandescent light; 2) 10% blue (447 ± 5 nm) / 90% red (627 ± 5 nm) LED light; 3) 20% blue / 80% red LED light; and 4) 40% blue / 60% red LED light as sole-source lighting at two different levels of fertility. All plants were harvested 30 d after seeding, and shoot and root tissues were analyzed for mineral nutrients. Lighting and fertility interacted to influence kale shoot and root mineral nutrient concentrations. Results indicate sole-source LED lighting used in production can impact mineral nutritional values of baby leafy greens now popular for the packaged market.

The cause-effect relationship between iron deficiency anemia (IDA) and osteoporosis has not been established in the general population. Thus, the current longitudinal study determined the role of IDA as a risk factor for osteoporosis by analyzing a large nationwide population-based sample. In a sample of 1,000,000 randomly sampled individuals from the 1998-2012 Taiwan National Health Insurance Research Database, patients with IDA (case group [n=35,751]) and individuals without IDA (control group [n=178,755]) were compared. Patients who were <20 years of age and who had pre-existing osteoporosis prior to the diagnosis of IDA were excluded. Each patient with IDA was age- and gender-matched to 5 individuals without IDA. The diagnoses of IDA and osteoporosis (coded using ICD-9CM) were further confirmed with blood test results and X-ray bone densitometry to ensure the accuracy of the diagnoses. Osteoporosis occurred more often among patients with IDA compared to individuals without IDA (2.27% vs. 1.32%, p<0.001). Cox proportional hazard analysis revealed that the risk for osteoporosis was significantly higher in the case than the control group (hazard ratio [HR]=1.74; 95% CI=1.61-1.88) and remained similar after adjustment for covariates (adjusted HR=1.81; 95% CI=1.67-1.97). Compared with individuals without IDA, the risk for osteoporosis was even higher for patients with IDA who received intravenous ferrum therapy (adjusted HR=2.21; 95% CI=1.85-2.63). In contrast, the risk for osteoporosis was reduced for patients with IDA who received a blood transfusion (adjusted HR=1.47; 95% CI=1.20-1.80). As a predictor, prior IDA is a significant and independent risk factor for development of osteoporosis. In contrast to blood transfusion treatment, the use of intravenous ferrum may further increase the risk for future osteoporosis.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

In the pursuit of energy efficiency and reduced environmental impact, adequate ventilation in enclosed spaces is essential. This study presents a hybrid neural network model designed for real-time monitoring and prediction of environmental variables. The system comprises two phases: An IoT hardware-software platform for data acquisition and decision-making, and a hybrid model combining short-term memory and convolutional recurrent structures. The results are promising and hold potential for integration into parallel processing AI architectures.

Human factors are the things that go wrong in the interactions between a team of people and a system of technology. This is part of a broader transdisciplinary field called engineering psychology, which as the name suggests, draws from both engineering and psychology. Many, if not most, catastrophic accidents involve a socio-technical interaction, i.e. are not solely due to technology failure. Hence, there is a need to consider human factors in the development or deployment of any technical system. This article is about the human factors involved in an aviation accident in New Zealand between a Yak and a cherry picker. The types of human error are identified, and the barrier bowtie method is used to represent them. The analysis gives different insights into the accident compared to the formal accident report, and better represents the human error characteristics.

(1) Background: Environmental and public health research has given considerable attention to the impact of air quality on brain health, with systematic reviews widespread. No literature review has been done for cognitive frailty – a multidimensional syndrome combining physical frailty and cognitive impairment and their apparent co-dependence, linked to increased vulnerability and adverse health outcomes, including dementia. Instead, cognitive decline and frailty is implicitly explored through research on air quality and comorbid cognitive and physical decline in elderly populations. (2) Methods: A scoping review was conducted to explore the need for a systematic review. Combining Arksey and O’Malley [1] and PRISMA-ScR checklist [2], a scoping review of SCOPUS using ‘cogniti*’ + ‘resilience’ + ‘air quality’ or ‘cogniti*’ + ‘ageing’ + ‘air quality’ resulted in N=2503 articles, screened and reduced using inclusion and exclusion criteria, to N=16 articles. (3) Results: Air quality appears to be a critical risk factor for cognitive decline, even at air quality levels below WHO targets. Moderate long-term ambient air pollution appears linked to increased risk of cognitive frailty, suggesting earlier and more active interventions to protect older people. There are varied effects on cognition across the life course, with both emotional and functional impacts. Effects may be more detrimental to elderly people with existing conditions, including economic and health inequalities. Generalisation of results is limited due to the absence of a dose-response, variations in methods, controlling for comorbid effects, and variance across studies. (4) Conclusions: The findings support the need for more research and a more extensive summary of the literature.

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH3, and other gases (GHGs, O3 – sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO2-based photocatalyst. Treated gas airflow (0.25 to 0.76 m3/s) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to i) 63% of odor, ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p-cresol, and indole, respectively, iii) 14% of nitrous oxide (N2O), iv) 100% of O3, and 26% generation of CO2. Under UV-C (185+254 nm) photocatalysis, the percent reductions of target gases were up to i) 54% and 47% for p-cresol and indole, respectively, ii) 25% of N2O, iii) 71% of CH4, and 46% & 139% generation of CO2 & O3, respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of analytes concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23-ga Car/PDMS assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 x 0.75 mm i.d. SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The developed model offers new insight into optimization of air and gas sampling using SPME.

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.