Ion Transport Membrane (ITM) is a well-developed technology for producing O₂ by separating air in its membrane. To decrease energy loss in air separation unit and to increase the overall efficiency of a power generation unit ITM is added with the gasification unit in this model. Ceramic materials are generally used to make ion transport membrane that produces oxygen by conducting oxygen ions at specified temperature. Potential advantages can be gained by integrating ITM technology with power generation units as 99% pure oxygen is produced from ITM. A salient comparison between ITM air separator combined with IGCC and cryogenic air separator combined with IGCC is done in this paper where the total power generation cycle remains same for both cases excluding the air separation units (ITM and cryogenic). Using ITM air separator is more beneficial compared to cryogenic air separation as ITM technology helps to improve IGCC overall efficiency and also reduces plant auxiliaries than that of power generation systems integrated with cryogenic.

Expression levels of Cav3.2, BKCa, and anoctamin 1 were previously found to be significantly elevated in patients with chronic kidney disease–associated pruritus (CKD-aP). On the other hand, the expression of TRPV1 was significantly reduced. We further compared CKD patients with and without CKD-aP in terms of the expression levels of several ion channels in the skin, including in peripheral nerve endings。Based on CKD-aP severity, subjects were divided into two groups: non-CKD-aP (no or slight pruritus; n = 16) and CKD-aP (mild, moderate, or severe pruritus; n = 16). Skin samples were obtained from the forearm or elbow during arteriovenous fistula surgery. We used quantitative real-time polymerase chain reaction to measure the skin expression levels of the following ion channels in the skin: Nav1.7, Kv7.2, TREK1, HCN2, TrkA, and Piezo2.　RT-PCR analyses showed that CKD-aP patients had significantly higher levels of TREK1 and Piezo2 transcripts and significantly lower levels of HCN2 transcripts than non–CKD-aP patients. No significant differences were noted between groups in the expression of Nav1.7 or TrkA. Moreover, Kv7.2 transcripts were not detected in either group. In skin samples collected from CKD-aP patients, ion channel expression patterns were altered to enhance hyperpolarization of pruriceptive neurons.

The voltage-gated potassium channel KV1.3 has been recognized as a tumor marker and represents a promising new target for the discovery of new anticancer drugs. We designed a novel structural class of KV1.3 inhibitors through structural optimization of benzamide-based hit compounds and structure-activity relationship studies. The potency, and selectivity of the new KV1.3 inhibitors were investigated using whole-cell patch- and voltage-clamp experiments. 2D and 3D cell models were used to determine antiproliferative activity. Structural optimization resulted in the most potent and selective KV1.3 inhibitor 44 in the series with an IC50 value of 470 nM in oocytes and 950 nM in Ltk cells. Kv1.3 inhibitor 4 induced significant apoptosis in Colo-357 spheroids, while 14, 37, 43, and 44 significantly inhibited Panc-1 proliferation.

Electric Vehicles (EVs) are the need of the hour due to growing climate change problems linked with the transportation sector. Battery Thermal Management System (BTMS), which is accountable for certifying safety and performance of lithium-ion batteries (LiB), is the most vital part of an EV. LiB has auspicious gravimetric energy density but the heat generation due to chemical reactions inside a LiB during charging and discharging causes temperature rise which has a direct effect on LiB performance and safety. This study specifically focuses on aircooled BTMS, defines different types of air-cooled BTMS (active and Passive), discusses limitations associated with air-cooled BTMS, and investigates different optimization techniques and parameters to improve performance of air-cooled BTMS. Maintaining temperature within optimum range and uniform temperature distribution between cells of a battery pack are the major design parameters for improving the performance and efficiency of air-cooled BTMS. Various optimization techniques including cell arrangement with a battery pack, air-flow channel optimization, and air inlet/outlet position variations are discussed and each technique is thoroughly reviewed. Finally, it’s noted that passive air-cooled BTMS is not that effective for long-distance vehicles so most researchers shifted their focus toward active air-cooled BTMS. Active air-cooled BTMS requires a lot of power for effective performance. Lastly, the most recent field of air-cooled BTMS technology which is Air-Hybrid BTMS is discussed and declared a very promising solution for overcoming major limitations associated with air-cooled BTMS.

Cadmium(II) contamination in the environment is an emerging problem due to its acute toxicity and mobility, so it is very urgent to remove this species from industrial wastewater before it is discharged into the environment. Thus, a starch-based activated carbon (AC) with a specific surface area of 1600 m2g-1 is used as an adsorbent for the capturing of toxic cadmium(II) ions from synthetic solutions. The sorbent is characterized by BET, SEM, TEM, XRD, FT-IR, TGA, and zeta potential. The maximum uptake (284 mg g-1) of Cadmium(II) ion is obtained at pH 6. The thermodynamic parameters like ∆G, ∆H, ΔS are found to be -17.42 kJmol-1, 6.49 kJ mol-1, and 55.66 Jmol-1K-1 respectively, revealing that the adsorption mechanism is endothermic, spontaneous, and feasible. The experimental data follows the D-R and Langmuir models well. The mass transfer is controlled by pseudo 2nd order kinetics. Furthermore, the density functional theory simulations demonstrate that the activated carbon strongly interacted with the Cd(II) ion through its various active sites. The adsorption energy noted for all interactive sites is highly negative (-0.45 eV to -10.03 eV), which shows that the adsorption process is spontaneous and stable which is in agreement with the experimental thermodynamics analysis.

Oleraceins are a class of indoline amide glycosides found in Portulaca oleracea L. (Portulacaceae), or purslane. These compounds are characterized with 5,6-dihydroxyindoline-2-carboxylic acid N-acylated with cinnamic acid derivatives, and many are glucosylated. Herein, hydromethanolic extracts of the aerial parts of purslane were subjected to UHPLC-Orbitrap-HRMS analysis, conducted in negative ionization mode. Diagnostic ion filtering (DIF), followed by diagnostic difference filtering (DDF), were utilized to automatically filter out MS data and select plausible oleracein structures. After an in-depth MS2 analysis, a total of 51 oleracein compounds were tentatively identified. Of them, 26 had structure matching one of already known oleraceins and the other 25 are new, undescribed in the literature structures, belonging to the oleracein class. Moreover, diagnostic fragment ions were selected, based on which clustering algorithms and visualizations were employed. As we demonstrate, clustering methods can provide valuable insights into the mass fragmentation elucidation of natural compounds in complex mixtures.

In this work, the transport equations of ionic species in concrete are studied. First, the equations at the porescale are considered, which are then averaged over a representative elementary volume. The so obtained transport equations at the macroscopic scale are thoroughly examined and each term is interpreted. Furthermore, it is shown that the tortuosity-connectivity does not slow the average speed of the ionic species down. The transport equations in the representative elementary volume are then compared with the equations obtained in an equivalent pore. Lastly, comparing Darcy’s law and the Hagen-Poiseuille equation in a cylindrical equivalent pore, the tortuosity-connectivity parameter is obtained for four dierent concretes. The proposed model provides very good results when compared with the experimentally obtained chloride profiles for two additional concretes.

Today, air quality is one of the global concerns that governments are facing. One of the main air pollutants is the particulate matter (PM) that affects human health. This article presents the modeling of a purification system by means of negative air ions (NAIs) for air pollutant removal, using computational intelligence methods. The system uses a high voltage booster output to ionize air molecules from stainless steel electrodes; its particle-capturing efficiency reaches up to 97%. With two devices (5 x 2 x 2.5 cm), 2 trillion negative ions are produced per second, and the particulate matter (PM 2.5) can be reduced from 999 to 0 mg / m3 in a period of approximately 5 to 7 minutes (in a 40 x 40 x 40 cm acrylic chamber). This negative ion generator is a viable and sustainable alternative to reduce polluting emissions, with beneficial effects on human health.

There is an increasing clinical need to develop novel biomaterials that combine regenerative and biocidal properties. In this work, we present the preparation of silver /silica based glassy bioactive (ABG) compositions via a facile, fast (20h), and low temperature (80 °C) approach and their characterization. The fabrication process included the synthesis of the bioactive glass (BG) particles followed by the surface modification of the bioactive glass with silver nanoparticles. The microstructural features of ABG samples before and after exposure to simulated body fluid (SBF) as well as their ion release behavior during SBF test were evaluated using infrared spectrometry (FTIR), ultraviolet- visible (UV-Vis) spectroscopy, X-ray diffraction (XRD), electron microscopies (TEM and SEM) and optical emission spectroscopy (OES). The antibacterial properties of the experimental compositions were tested against Escherichia coli (E. coli). The results indicated that the prepared ABG materials possess antibacterial activity against E. coli, which is directly correlated with the glass surface modification.

A mathematical expression to describe cation absorption of root is expressed with simulation results. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient. The gradient promotes external positive ions to flow into the roots, while carries negatively charged particles with symport. In this paper, a mathematical model whose independent variables are the concentrations of external and internal cation is presented. This differential equation is induced from Ohm’s law. The equation has terms for plant physiology, ion’s physical and electrical properties, growth of plant, and interaction between the root and the surroundings. Simulation showed that the physiology-related coefficient has important role on nutrition absorption.

In this study, literature on pore structure and chloride ion diffusivity was collected to investigate the correlation of pore structure indicators with diffusivity. Good correlation between total porosity and chloride ion diffusivity was found when the samples did not contain admixture materials and diffusion test was conducted without acceleration. Pore diameter indicators did not correlate with diffusivity. The diffusivity of cement paste was reduced by admixture materials compared to that without admixture materials even if the total porosity is the same. On the other hand, the diffusivity of concrete was not reduced by admixture materials.

Sodium substitution Li1-xNaxMn2O4 cathodes were synthesized by a solid-state reaction method. The morphologies and crystal structures of Li1-xNaxMn2O4 were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. All Li1-xNaxMn2O4 samples exhibited a single phase LiMn2O4 spinel structure with good crystallinity. The effect of Na+ ions on the electrochemical performance of Li1-xNaxMn2O4 was investigated by galvanostatic charge-discharge test. The results showed that lithium substituted by sodium deteriorated its capacity retention but enhance its discharge capacity when it worked at large current densities. The initial discharge capacity was 114.2 mAh/g for Li0.94Na0.06Mn2O4, and 93.1 mAh/g remained after 300 cycles at a current density of 2220 mA/g in the voltage range 3.0–4.3 V at room temperature.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

The Conus genus includes around 500 species of marine mollusks with a peculiar production of venomous peptides known as conotoxins (CTX). Each species is able to produce up to 200 different biological active peptides. Common structure of CTX is the low number of aminoacids stabilized by disulfide bridges and post-translational modifications that give rise to different isoforms. µ and µ-O CTX are two isoforms that specifically target voltage-gated sodium channels. These, by inducing the entrance of sodium ions in the cell, modulate the neuronal excitability by depolarizing plasma membrane and propagating the action potential. Hyperxcitability and mutations of sodium channels are responsible for perception and transmission of inflammatory and neuropathic pain states. In this review, we describe the current knowledge of µ-CTX interacting with the different sodium channels subtypes, the mechanism of action and their potential therapeutic use as analgesic compounds in the clinical management of pain conditions.

The migration from MATLAB to Python (M-to-PY) has gained significant traction in recent computational research. While MATLAB has long served as a linchpin in myriad scientific endeavors, there's an emerging trend to rejuvenate these projects using Python's extensive AI tools and libraries. This study presents a semi-automated process for M-to-PY conversion, using a detailed case study of an image skeletonization project comprising fifteen MATLAB files and a 1404-image dataset. Skeletonization is foundational for ongoing 3D motion detection research using AI transformers, predominantly developed in Python. The utilization of ChatGPT-4, acting as an AI co-programmer, is pivotal in this conversion. By leveraging the public OpenAI API, we developed an M-to-PY converter prototype, evaluated its efficacy using test cases from the Bard bot, and subsequently employed the converted code in an AI application. The dual contributions encompass a well-tested M-to-PY converter and a Skeleton App capable of sketching and skeletonizing any given image, enriching the AI toolset. This study accentuates how AI resources, like ChatGPT-4, can simplify code transitions, opening doors for innovative AI implementations using primarily MATLAB-coded scientific research.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

To investigate the effect of prohexadione-calcium (Pro-Ca) primed on seed germination and seedling growth of oilseed rape under salt stress, to alleviate the inhibition of soil salinization on the growth of oilseed rape, and to improve the sustainability of agricultural production. Using Huayouza 158R and Huayouza 62 as test materials, the regulation of seed germination and seedling growth under the stresses of 0, 100, and 150 mM NaCl (S0, S100, and S150) was investigated after the primed of Pro-Ca. We conducted six treatments, S0: non-primed + 0 mM NaCl, PCS0: Pro-Ca primed + 0 mM NaCl, S100: non-primed + 100 mM NaCl, PCS100: Pro-Ca primed + 100 mM NaCl, S150: non-primed + 150mM NaCl, Pro-Ca+S150: Pro-Ca primed + 150 mM NaCl. The results showed that salt stress inhibited seed germination and seedling growth, and Pro-Ca primed significantly increased the germination index and vigor index of oilseed rape seeds. The average germination time and malondialdehyde (MDA) content were significantly reduced, which resulted in the optimal initiation fiddling concentration of 8mg·L-1. The morphological parameters of oilseed rape decreased significantly under salt stress, with leaf area decreasing by 70.69% and 75.03% and total chlorophyll content decreasing by 18.55% and 18.68% at S150. With the rise of salt stress, the changes of each photosynthetic parameter were somewhat similar, and Pn, Gs, Ci, and Tr continued to decline, indicating that the effects of salt stress on photosynthesis in oilseed rape might be mainly attributed to stomatal restriction and inhibition of photosynthetic pigment synthesis. While Na+ and MDA contents increased significantly, reaching a peak at S150, indicating that Na+ content increased significantly under salt stress, which resulted in the slow growth of oilseed rape and weak plants under the influence of Na+ salt damage. After Pro-Ca primed, leaf area and photosynthetic pigment synthesis increased, and the initiation treatment promoted the rise of Pn, Gs, Ci, and Tr under salt stress. The Na+ content decreased by 7.29% and 6.96% in PCS100 compared with S100, decreased by 9.23% and 25.02% in PCS150 compared with S150, and increased in K+ and Mg2+ after Pro-Ca primed. At this time, the antioxidant enzyme activities increased, and the MDA content and relative conductivity decreased. It was concluded that Pro-Ca primed improved the photosynthetic capacity of oilseed rape by promoting leaf growth, stomatal opening, and photosynthetic pigment synthesis. At the same time, reducing Na+ content and promoting K+ and Mg2+ absorption and antioxidant enzyme activities together alleviate salt damage and improve salt tolerance of oilseed rape.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

The precise determination of the State-of-Health (SOH) of lithium-ion batteries is critical in the domain of battery management systems. The proposed model in this research paper emulates any deep learning or machine learning model by utilizing a Look Up Table (LUT) memory to store all activation inputs and their corresponding outputs. The operation that follows the completion of training is referred to as the LUT memory preparation procedure. The lookup operation performed on this method simply substitutes for the inference process. This is achieved by discretizing the input data and features before binarizing them. The term for the aforementioned operation is the LUT inference method. The procedure was evaluated in this study using two distinct neural network architectures: a bidirectional long short-term memory (LSTM) architecture and a standard fully connected neural network (FCNN). It is anticipated that considerably greater efficiency and velocity will be achieved during the inference procedure when the pre-trained deep neural network architecture is inferred directly. The principal aim of this research is to construct a lookup table that effectively establishes correlations between the SOH of lithium-ion batteries and ensures a degree of imprecision that is tolerable. According to the results obtained from the NASA PCoE lithium-ion battery dataset, the proposed methodology exhibits performance that is largely comparable to that of the initial machine learning models. Utilising the error assessment metrics RMSE, MAE, and (MAPE), the accuracy of SOH prediction has been quantitatively evaluated. The indicators mentioned above demonstrate a significant degree of accuracy when predicting SOH.

PIEZO1 plays a crucial role in the human body as a mechanosensory ion channel. It has been demonstrated that PIEZO1 is important in tissue development and regulating many essential physiological processes. Studies have suggested that the PIEZO1 ion channel plays a role in invasion and progression in cancer; elevated levels of PIEZO1 have been correlated with increased migration in breast cancer cells, chemo-resistance and invasion in gastric cancer cells, and increased invasion of osteosarcoma cells. In addition, high PIEZO1 expression levels were correlated with a worse prognosis in glioma patients. On the other hand, studies in lung cancer have attributed high PIEZO1 levels to better patient outcomes. However, the clinical impact of PIEZO1 in breast cancer is not well characterized. Therefore, our goal was to determine the clinical relevance of PIEZO1 in breast cancer. Analysis of breast cancer data from The Cancer Genome Atlas (TCGA) was conducted to investigate PIEZO1 expression levels and correlation to survival, followed by validation in an independent dataset, GSE3494. We also performed gene set enrichment analysis (GSEA) and analyzed immune cell levels in breast tumors from TCGA through a CIBERSORT algorithm. Our results demonstrated that PIEZO1 expression levels are higher in hormone receptor (HR) negative than HR positive cohorts. High PIEZO1 expression is correlated with a significant decrease in survival in HR negative cohorts, suggesting that PIEZO1 could be utilized as a prognostic biomarker in HR negative breast cancer. GSEA showed that various signaling pathways associated with more invasive phenotypes and resistance to treatments, including epithelial-mesenchymal transition (EMT), hypoxia, and multiple signaling pathways, are enriched in high PIEZO1 HR negative tumors. Our results also demonstrated a decrease in CD8+ and CD4+ T cell infiltration in high PIEZO1 HR negative tumors. Further investigations are necessary to elucidate the mechanistic roles of PIEZO1 in HR negative breast cancer.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

Thermal safety of lithium-ion traction batteries is a highly concerned issue in the field of electric transportation. The large amount of gas emission during the thermal runaway process of batteries has highly safety hazards such as fire and explosion. Quantitative analysis of emission is one of the important challenges for testing and evaluating battery safety. Focus on quantifying the gas emission through large-scale thermal propagation in battery modules and packs, based on the idea of cell result multiplication, this article conducts thermal runaway emission analysis on single cell and modules, and compares the behavior of thermal runaway and gas emission of the cell and module from the aspects of temperature, pressure, gas composition and battery morphology. The feasibility of the cell result multiplication method was verified from the perspective of experimental data.

The main property of tripodal ligands is the predictable type of coordination. Homo- and heteroleptic lanthanide complexes with tripodal ligands are a representative class of compounds. However, despite the fact that many of them are paramagnetic their magnetic behavior is poorly understood. This is because their photophysical and catalytic properties have been more attractive. In the present review, we are trying to summarize the available structural information and extremely few data on magnetic properties in order to draw some conclusions about the prospective of tripods using in the design of quantum molecular magnets based on Ln ions. We would like to draw the reader's attention to the fact that despite the consideration of a large part of the currently known lanthanide compounds with tripodal ligands, this review is not exhaustive. However, our goal was to draw the attention of researchers to the fact that a whole niche of air-stable Ln complexes remained outside the attention of magnetochemists and theoreticians.

Lithium-ion batteries with improved energy densities have made understanding the Solid Electrolyte Interphase (SEI) generation mechanisms that cause mechanical, thermal, and chemical failures more complicated. SEI processes reduce battery capacity and power. Thus, a review of this area's understanding is important. It is essential to know how batteries degrade in EVs to estimate battery lifespan as it goes, predict, and minimize losses, and determine the ideal time for a replacement. Lithium-ion batteries used in EVs mainly suffer two types of degradation: calendar degradation and cycling degradation. Despite the existence of several existing works in the literature, several aspects of battery degradation remain unclear or have not been analyzed in detail. This work presents a systematic review of existing works in the literature. The results of the present investigation provide insight into the complex relationships among various factors affecting battery degradation mechanisms. Specifically, this systematic review examined the effects of time, side reactions, temperature fluctuations, high charge/discharge rates, depth of discharge, mechanical stress, thermal stress, and the voltage relationship on battery performance and longevity. The results revealed that these factors interact in complex ways to influence the degradation mechanisms of batteries. For example, high charge currents and deep discharges were found to accelerate degradation, while low temperatures and moderate discharge depths were shown to be beneficial for battery longevity. Additionally, the results showed that the relationship between cell voltage and State-of-Charge (SOC) plays a critical role in determining the rate of degradation. Overall, these findings have important implications for the design and operation of battery systems, as they highlight the need to carefully manage a range of factors to maximize battery performance and longevity. The result is an analysis of the main articles published in this field in recent years. This work aims to present new knowledge about fault detection, diagnosis, and management of lithium-ion batteries based on battery degradation concepts. The new knowledge is presented and discussed in a structured and comprehensive way.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

This paper presents an improved SOC estimation method for lithium ion batteries in Electric Vehicles using Bayesian optimized feedforward network. This innovative bayesian optimized neural network method attempts to minimize a scalar objective function by extracting hyperpa-rameters (hidden neurons in both layers) using a surrogate model. Furthemore, the hyperparameters are built and data samples are trained and validated. The performance of the proposed deep learning neural network is evaluated. Two reasonable size data samples are ex-tracted from Panasonic 18650PF Li-ion Mendeley datasets that are used for training and valida-tion. RNN and LSTM neural network algorithms offer the common core property of retaining past information and/or hidden states for better SOC estimation. However, the feature of this pro-posed method is the inclusion of Bayesian optimization that chooses optimal double layer hidden neurons. Analysis of results shows that Bayesian optimized feedforward algorithm with average MAPE (0.20%) is the lowest and is the best selection compared with average MAPE for other five deep learning algorithms. In the last quarter of fuel gauge, where fuel anxiety is severe, feed-forward with Bayesian Optimization algorithm is still the best selection (with MAPE of 0.64%).

Nitrogen (N) is a major limiting factor for plant growth and vegetable production. Understanding the regulatory mechanisms of N uptake, transport, and assimilation is key to improving nitrogen use efficiency in plants. Ammonium transporters (AMTs) play an important role in plant N metabolism. In this study, we isolated an important AMT1 subfamily member (BcAMT1;5) with a highly conserved signatural AMT1 subfamily motif from flowering Chinese cabbage. Based on functional complementation in yeast mutant 31019b and overexpression of BcAMT1;5 in Arabidopsis, BcAMT1;5 is a functional ammonium transporter. Tissue expression analysis showed that BcAMT1;5 was mainly expressed in roots and showed multiple N regime transcript patterns to respond to varying nutritional conditions. This was up-regulated by N-deficiency and down-regulated by supplying NH4+. The glucuronidase (GUS) activities of BcAMT1;5pro::GUS showed a similar change in response to different N conditions. Overexpression of BcAMT1;5 accelerated the growth of transgenic seedlings, increased NH4+ net influxes, and enhanced the content and accumulation of NH4+ and NO3- at low N concentrations. Additionally, it increased the transcript levels of N assimilation-related genes in shoots. These results indicate that the transcriptional regulation of BcAMT1;5 in flowering Chinese cabbage may participate in N uptake and assimilation under various N conditions.

The abundant use of lithium-ion batteries (LIBs) in a wide variety of electric devices and vehicles will generate a large number of depleted batteries, which contain several valuable metals such as Li, Co, Mn, and Ni present in the structure of the cathode material (LiMO2). The present work investigates chemical, technological, and environmental aspects in the treatment of such wastes, development of a methodology for the extraction of lithium, cobalt, nickel, manganese, and graphite by a carbochlorination pyrometallurgical process. Mixtures of cathode and anode materials (called black mass, mixed oxides of Li, Co, Ni, Mn, and graphite) from different LIBs, carbon black (as reducing agent), and CaCl2 (as chlorinating agent) were used. Non-isothermal thermogravimetric tests up to 850°C and isothermal tests at 700°C of the mixtures in an inert atmosphere were carried out. It was experimentally observed that the LiMO2-C-CaCl2 reaction takes place at 700°C. LiCl, Ni, and Co were obtained as final products, and to a lesser extent, CoO, NiO, and MnO2. CaCO3 was also obtained as a by-product. The obtained results show that carbochlorination is an efficient and effective alternative route for the extraction and recovery of metals from different LIBs, focused on the sustainability and circular economy

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

Two mononuclear Ru(III) complexes of formula trans-[RuCl4(Hgua)(dmso)]·2H2O (1) and trans-[RuCl4(Hgua)(gua)]·3H2O (2) [Hgua = protonated guanine (gua), dmso = dimethyl sulfoxide] have been synthesized and characterized magnetostructurally. Compounds 1 and 2 crystallize in the monoclinic system with space groups P21/n and Pc, respectively. Each Ru(III) ion in 1 and 2 is six-coordinate and bonded to four chloride ions and one (1) or two (2) nitrogen atoms from guanine molecules and one sulfur atom (1) of a dmso solvent molecule, generating quasi regular octahedral geometries in both cases. In their crystal packing, the Ru(III) complexes are self-assembled mainly through an extended network of N-H⋯Cl hydrogen bonds and π⋯Cl type intermolecular interactions, forming novel supramolecular structures based on this paramagnetic 4d metal ion. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a different magnetic behavior. While 1 is a ferromagnetic compound at low temperature, 2 exhibits a behavior typical of noninteracting mononuclear Ru(III) complexes with S = 1/2. Ac magnetic susceptibility measurements reveal slow relaxation of the magnetization in the presence of external dc fields only for 2, hence indicating the occurrence of field-induced single-ion magnet (SIM) phenomenon in this mononuclear guanine-based Ru(III) complex.

In this work, polyacrylic acid-functionalized MCM-41 was synthesized, which was further interacted with calcium ions, to realize enhanced pH-responsive nanocarrier for sustained drug release. First, mesoporous silica nanoparticles (MSNs) were prepared by the sol-gel method. Afterward, (3-trimethoxysilyl)propyl methacrylate (TMSPM) modified surface was prepared by using the post-grafting method, then polymerization of acrylic acid was proceeded. After adding calcium chloride solution, polyacrylic acid-functionalized MSNs with calcium-carboxyl ionic bonds in the polymeric layer, which can prevent the cargo from leaking out of the mesopore, were prepared. The structure and morphology of the modified nanoparticles (PAA-MSNs) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, etc. The controlled release of guest molecules was studied by using 5-fluorouracil (5-FU). The drug molecules-incorporated nanoparticles showed different releasing rates under different pH conditions. It is considered that our current materials have the potential as pH-responsive targeted nanocarriers in the field of medical treatment.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

Current physiology attributes the mechanism of membrane potential generation to transmembrane ion transport, but ion adsorption could just as well play this fundamental role. The evidence shows that the ion adsorption mechanism accurately reproduces the experimentally measured membrane potential. The Goldman-Hodgkin-Katz equation (GHK eq.) and the Nernst equation (Nernst eq.) are the typical mathematical formulas representing the membrane potential in current physiology. However, the authors were able to show that the potential formulas by ion adsorption mechanism give identical results to GHK eq. and Nernst. eq. Our experimental and theoretical analyses suggest that there is a special relationship between the membrane potential and the membrane surface charge density, and this unique equation inevitably leads to the establishment of a GHK eq and/or a Nernst eq. The authors found that the unique equation is the foundation of thermodynamics “Boltzmann distribution”. Thus, the GHK eq. and the Nernst eq. are simply the natural consequence of thermodynamics from the view of the ion adsorption mechanism.

Considering the ever-increasing role of rare-earth elements (REE) in the modern hi-tech field, their effective use has a tremendous significance, although the production process is inevitably linked to the large volumes of industrial ammonia effluents and heavy metal wastes. In the process of metallurgical separation of metals, the emission of large volumes of noxious gases and radioactive substances is inevitable. Lean technogenic raw material processing is sensible under the condition of the development of non-waste technology. The lack of competent regulations governing the disposal of waste containing REE has an impact on adjacent territories, accumulating in water bodies and, as a result, in the human body. Such an impact cannot pass without a trace, however, the ambiguity of opinions in the scientific community regarding the toxic effects of REE on living organisms determines the relevance of a more detailed study of this issue. The paper presents experimental and theoretical results of studies of ion flotation in the aqueous solutions containing ytterbium cations and a surfactant as a collector - sodium dodecyl sulphate (NaDS).

Ag+ pollution is great of harm to the human body and the biology. Therefore, it is an urgent need to develop inexpensive and accurate detection methods. Herein, lignin-derived structural memory carbon nanodots (CSM-dots) with outstanding fluorescence property were fabricated via a green method, which reserve functional and structural units of the precursor molecules. The CSM-dots could specifically bind Ag+, accompanied with a remarkable fluorescence quenching response. This “turn-off” fluorescence behavior was used for Ag+ determination in a linear range of 5-290 μM with the detection limit as low as 500 nM. Furthermore, the finding showed that this sensing nano-platform was successfully used for Ag+ determination in real samples and intracellular imaging, showing great potential in biological and environmental monitoring applications.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

The molecular dynamics simulation has been used to investigate the structural and transport properties of (Ba_0.5-xSr_x)La_0.5InO_3-δ (x=0, 0.1, 0.2) oxygen-ion conductor. The previous studies reported that the ionic conductivity of Ba-doped LaInO3 decreases because Ba dopant forms narrow oxygen path in the lattice, which could hinder the diffusion of oxygen ion. In this study, we reveal the mechanism to improve the ionic conductivity by Ba and Sr co-doping on La site in LaInO3 perovskite oxide. The results show that the ionic conductivity of (Ba_0.5-xSr_x)La_0.5InO_3-δ increases with increasing numbers of Sr ions, which oxygen diffusion paths including Sr ion have larger critical radius than Ba ions. The RDF calculations showed the heights of peak in composition including Sr ions is lower and broaden, so oxygen ions moved easily into other oxygen sites.

Electric vehicles (EVs) are being endorsed as the uppermost successor to fuel-powered cars, with timetables for banning the sale of petrol-fueled vehicles announced in many countries. However, the range and charging times of EVs are still considerable concerns. Fast charging could be a solution to consumers' range anxiety and the acceptance of EVs. Nevertheless, it is a complicated and systematized challenge to realize the fast charging of EVs because it includes the coordinated development of battery cells, including electrode materials, EV battery power systems, charging piles, electric grids, etc. This paper aims to serve as an analysis for the development of fast-charging technology, with a discussion of the current situation, constraints and development direction of EV fast-charging technologies from the macroscale and microscale perspectives of fast-charging challenges. It is emphasized that to essentially solve the problem of fast charging, the development of new battery materials, especially anode materials with improved lithium ion diffusion coefficients, is the key. It is highlighted that red phosphorus is the most promising anode that can simultaneously satisfy the double standards of high-energy density and fast-charging performance to a maximum degree.

Driven by the rapid uptake of battery electric vehicles, Li-ion power batteries are increasingly reused in stationary energy storage systems, and eventually recycled to recover all the valued components. Offering an updated global perspective, this study provides a circular economy insight on lithium-ion battery reuse and recycling.

We have studied on the stress measurement by making use of salivary nitrate, which can be a candidate of stress markers, with ion-selective field-effect transistors (ISFETs). ISFETs are suitable for on-site single-drop analysis of salivary nitrate within 10 seconds. However, when ISFETs are used for salivary nitrate, ISFETs have a problem which is called the initial drift. The initial drift makes it difficult for determination of an accurate nitrate monitoring. Thus, the purpose of this study is to suppress an initial drift and to search for new easy polymer to possess more performance of sensor responses than conventional matrix membrane such as PVC. In this research, we investigated ISFETs using specific matrix membrane for example, KP-13, Pellethane^® and P7281-PU. The initial drift was evaluated from the fluctuation of the response values generated by ISFETs which are immersed in saliva or aqueous solution. As a result, P7281-PU showed its suppression effect for the initial drift in the whole saliva and various solutions. Furthermore, the cause of drift may be H⁺ diffusion, and drift suppression effect of P7281-PU may be affected by urethane bond capturing H⁺ in ion-selective membrane. This result suggests a continuous nitrate monitoring and development of wearable sensors.

The structural, electronic and magnetochemical properties of the star-shaped polyoxopalladate [Pd₁₅O₁₀(SeO₃)₁₀]¹⁰⁻ (POPd) and its lanthanide functionalized derivatives have been investigated on the basis of density functional theory followed by a ligand field analysis using the Radial Effective Charge (REC) model. Our study predicts that heteroPOPd is a robust cryptand that enforces D_5h symmetry around the encapsulated Ln³⁺ centers. This rigid coordination environment favors interesting potential magnetic behavior in the Er and Ho derivatives, which may be of interest for molecular spintronics and quantum computing applications.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

Batteries are called to be part of the electricity grid by providing ancillary services. Area regulation services seem to provide substantial revenues and profit. But Li-ion batteries are still too expensive to enter widely into this market. On the other hand, electric vehicle batteries are considered inappropriate for traction purposes when they reached a state of health of 80%. The reuse of these batteries offers affordable batteries for second life stationary applications. This study analyzes how batteries may provide services to a gas turbine cogeneration power plant and how long these batteries may last under different loads.

The present study investigates the relationship between the local structure, photocatalytic ability, and cathode performances in sodium-ion batteries (SIBs) and lithium-ion batteries (LIBs) using Ni-substituted goethite nanoparticles (Ni_xFe_1-xOOH NPs) with a range of 'x' values from 0 to 0.5. The structural characterization was performed applying various techniques, including X-ray diffractometry (XRD), Thermogravimetry differential thermal analysis (TG-DTA), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray absorption spectroscopy (XANES/EXAFS), both measured at room temperature (RT), and ⁵⁷Fe Mössbauer spectroscopy recorded at RT and at low temperatures (LT) from 20 K to 300 K, Brunauer-Emmett-Teller surface area measurement (BET), and diffuse reflectance spectroscopy (DRS). In addition, the electrical properties of Ni_xFe_1-xOOH NPs were evaluated by impedance spectroscopy. XRD showed the presence of goethite as the only crystalline phase in prepared samples with x ≤ 0.20, and goethite and α-Ni(OH)₂ in the samples with x > 0.20. Sample with x = 0.10 (Ni10) showed the highest photo-Fenton ability with a first-order rate constant value (k) of 15.8×10^-3 min^-1. The ⁵⁷Fe Mössbauer spectrum of Ni0, measured at RT, displayed a sextet corresponding to goethite, with an isomer shift (δ) of 0.36 mm s^-1 and a hyperfine magnetic distribution (B_hf) of 32.95 T. Moreover, the DC conductivity decreased from 5.52×10^-10 to 5.30×10^-12 (Ω.cm)^–1 with 'x' increasing from 0.10 to 0.50. Ni20 showed the highest initial discharge capacity of 223 mAh g^-1, attributed to its largest specific surface area of 174.0 m² g^-1. In conclusion, Ni_xFe_1-xOOH NPs can be effectively utilized as visible-light-activated catalysts and active cathode materials in secondary batteries.

There were designed and synthesized two new sulfone 2-aminobenzimidazole derivatives. Coordination compounds were obtained with nickel(II), copper(II), zinc(II), cadmium(II) and mercury(II) and these novel ligands. There were fully characterized by spectroscopic and analytical techniques. Single crystal X-ray structural analysis was performed on order to study the relevant intra and inter non-covalent interactions, mainly H...π, lone pair·...π, π...π, highlighting the difference between the ethyl and phenyl groups in such interactions. Dimeric and trimeric supramolecular syntons were found for some of these compounds. Their biological activity was investigated, being the copper(II) compounds with the sulfone phenyl derivative the most active.

In this study, multilayer composite nanofiber membranes of sodium alginate (SA) /polyethyleneimine (PEI)/polyvinyl alcohol (PVA) was fabricated via electrospinning technique to enhance the adsorption of Cu2+ from wastewater. The preparation and adsorption mechanisms of the SA/PEI/PVA nanofiber membranes were analyzed by utilizing analytical techniques such as SEM, FTIR, EDS, UV-vis, XRD, and TG. The obtained nanofiber membrane characterized by small diameter, high uniformity, and extensive surface area, demonstrate significant potential for heavy metal ion filtration. Optimal spinning parameters were identified, including a voltage of 19.5 KV, a distance of 8 cm, and specific mass ratios (SA: PEI: PVA, 1:2:6) and injection speeds (8 μL/min) and. The resulting nanofibers with an average diameter of 112.5 nm exhibited excellent morphology and high efficiency, retaining over 85% adsorption capacity for Cu2+ in initial tests and maintaining above 80% efficacy through four successive filtration cycles.

The vagina is an essential component of the female reproductive system and is responsible for providing female sexual satisfaction. Vaginal smooth muscle contraction plays a crucial role in various physiological processes, including sexual arousal, childbirth, and urinary continence. In pathophysiological conditions such as pelvic floor disorders, aberrations in vaginal smooth muscle function can lead to urinary incontinence and pelvic organ prolapse. A set of cellular and sub-cellular physiological mechanisms regulates the contractile properties of the vaginal smooth muscle cells. Calcium influx is a crucial determinant of smooth muscle contraction, facilitated through voltage-dependent calcium channels and calcium release from intracellular stores. Comprehensive reviews on smooth muscle biophysics are relatively scarce within the scientific literature, likely due to the complexity and specialized nature of the topic. The objective of this review is to provide a comprehensive description of alterations in the cellular physiology of vaginal smooth muscle contraction. The benefit associated with this particular approach is that conducting a comprehensive examination of the cellular mechanisms underlying contractile activation will enable the creation of more targeted therapeutic agents to control vaginal contraction disorders.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

The physiological mechanism of membrane potential generation relies on the passage of mobile ions across the plasma membrane, which is selectively permeable to mobile ions. The existence of a membrane and the transport of ions across it are essential for the generation of membrane potential. However, a long-forgotten theory, Association-Induction hypothesis, asserts that the heterogeneous distribution of charges in space, due to ion adsorption, is the true cause of membrane potential generation. Using an artificial living cell model consisting of a viscous aqueous solution, the mechanism of membrane potential generation is restudied in this work. The results indicate that membrane potential can be generated even in the absence of a plasma membrane and that ion adsorption leading to a heterogeneous spatial charge distribution is an essential factor for membrane potential generation. Consequently, the authors invites people to reconsider the Association-Induction hypothesis as a genuine mechanism for generating membrane potential.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

Pyridoxine is a versatile molecule that forms part of the family of B vitamins. It is used to treat and prevent vitamin B6 deficiency and certain type of metabolic disorders. Besides, pyridoxine molecule has been investigated as a suitable ligand toward metal ions. Nevertheless, the study of the magnetic properties of metal complexes containing lanthanide(III) ions and this biomolecule has been unexplored. We have synthesized and characterized a novel pyridoxine-based GdIII complex of formula [Gd(III)(pyr)2(H2O)4]Cl3 • 2 H2O (1) [pyr = pyridoxine]. 1 crystallizes in the triclinic system with space group Pī. In its crystal packing, the cationic [Gd(pyr)2(H2O)4]3+ entities are linked each other through H-bonding interactions involving non-coordinating water molecules and chloride anions. In addition, Hirshfeld surfaces of 1 were calculated to further investigate their intermolecular interactions in the crystal lattice. The study of the magnetic properties of 1 through ac magnetic susceptibility measurements reveals the occurrence of slow relaxation of magnetization in this mononuclear Gd(III) complex, this fact indicating an unusual single-ion magnet (SIM) behavior. We have also studied the relaxometric properties of 1, as a potential contrast agent for high-field MR imaging, from solutions of 1 prepared in physiological serum (0.0 - 3.2 mM range) and measured at 3 T on a clinical MR scanner. The relaxivity values obtained for 1 are larger than those of some commercial MR imaging contrast agents based on mononuclear Gd(III) systems

The swelling behavior of titanium-modified austenitic stainless steel 15-15Ti was investigated by pre-implantation of He at room temperature followed by Ni irradiation at 580 °C to peak doses of 120, 240 and 400 dpa. Relatively smaller cavities were observed in the zone of helium implantation while large cavities appeared in the region near the damage peak. A correction formula of the dpa curve was proposed and applied for samples with large swelling. It is found that the steady-state swelling rate of 15-15Ti keeps at ~1% /dpa even to high doses. By comparing the swelling data of the helium-implanted and helium-free regions at same doses, 70 dpa and 122 dpa, the suppression of excessive helium on swelling can be deduced at such doses.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

In this study, we investigated the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material by coating it with ZnO and examined the changes in surface composition using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, we investigated the electrochemical properties, including discharge capacity and initial irreversible capacity, of the modified materials. The results revealed that ZnO predominantly existed on the material surface, exerting influence on both surface composition and electrochemical characteristics. As the ZnO coating amount increased, the nickel and manganese content on the material surface also increased, and heat treatment at 400 °C resulted in the formation of composite oxides of transition metals and zinc on the material surface. The bonding energy of transition metals increased, and ZnO coating at a mass fraction of 2 % effectively suppressed irreversible reactions around 3.6 V at 55 °C, thereby improving initial coulombic efficiency. Battery materials coated with 2% ZnO exhibited optimal discharge capacity and cycle life at 55 °C/0.5 C.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

The carotid body is a major peripheral chemoreceptor that senses changes in arterial blood oxygen, carbon dioxide, and pH, what is important for regulation of breathing and cardiovascular function. The mechanisms by which the carotid body senses O2 and CO2 are well known; conversely, the mechanisms by which it senses pH variations are almost unknown. Here we used immunohistochemistry to investigate how the human carotid body contributes to the detection acidosis analyzing whether it expresses acid-sensing ion channels (ASIC) ion channels, and to know if these channels are in the cells chemosensory glomic cells or in the afferent nerves. ASIC1, ASIC2 and ASIC3, and to a much lesser extent ASIC4, immunoreactivity was detected in subpopulations of type I glomus cells, as well as in the nerves of the carotid body. In addition, immunoreactivity was found for all ASIC subunits in neurons of the petrosal and superior cervical sympathetic ganglia, where afferent and efferent neurons are located, respectively, innervating the carotid body. This study reports for the fist time the occurrence of ASIC proteins in the human carotid body, demonstrating that they are present in glomus chemosensory cells (ASIC1 < ASIC2 > ASIC3 > ASIC4) and nerves, presumably both afferent an efferent supplying the organ. These results suggest that the detection of acidosis by the carotid body can be mediated by ASIC ion channels present in the type I glomus cells or directly by sensory nerve fibers.

A single-crystal of ytterbium-doped “mixed” yttrium-lutetium aluminium garnet with a stoichiometric composition of (Y0.601Lu0.233Yb0.166)3Al5O12 was grown by the Czochralski method and its structure, vibronic, spectroscopic and laser properties were studied. The stimulated-emission cross-section for Yb3+ ions was maximized to 2.53×10-20 cm2 at 1031 nm, the emission bandwidth is ~8 nm and the reabsorption-free luminescence lifetime of the 2F5/2 state is 1.063 ms. Pumped at 941 nm, the Yb-laser generated a maximum output power of 1.04 W at 1.03 and 1.05 μm with a high slope efficiency of 76.4% and a laser threshold of 76 mW. A continuous wavelength tuning over a range of 51.6 nm (1026.4 - 1078.0 nm) was also achieved. Power scaling is achieved using a 969 nm-diode pumped microchip cavity. A maximum output power of ~9 W is obtained at 1.05 μm with a slope efficiency of 76% and with an almost circular laser beam profile.

(1) Background: The synthesis of core-shell magnetic mesoporous nanoparticles (MMSN) from phase transfer process is usually performed at 100-250 mg scale. At the gram scale, nanoparticles without core or with multicore systems are observed. (2) Methods: Iron oxide core nanoparticles (IO) were synthesized through thermal decomposition procedure of -FeO in oleic acid. Phase transfer from chloroform to water was then performed in order to wrap IO with mesoporous silica shell through the sol-gel procedure. MMSN were then functionalized with DTPA, and used for the separation of metal ions. Their toxicity was evaluated (3) Results: The phase transfer pro-cedure was crucial to obtained MMSN at large scale. Three synthesis parameters were rigorously controlled: temperature, time and glassware. Homogeneous dispersion of MMSN at the gram scale was successfully obtained. After functionalization with DTPA, the MMSN-DTPA were shown to have a strong affinity for Ni ions. Furthermore toxicity was evaluated in cells, zebrafish and through seahorse metabolic assays, and the nanoparticles were found nontoxic. (4) Conclusions: We developed a method of preparation of MMSN at the gram scale. After function-alization with DTPA, the nanoparticles were efficient in metal ion removal and separation, fur-thermore, no toxicity was noticed up to 125 µg.mL-1 in zebrafish.

The demand for high-energy-density batteries necessitates novel anode materials. Transition metal oxides (TMOs) show promise due to their high capacity, sustainability, and cost-effectiveness. However, TMO-based anodes face challenges related to expansion and conductivity. This study presents a two-step dilution crystallization method to fabricate porous ZnO nanoflowers at a moderate temperature. In-situ integration with carbon nanotube dispersants enhances conductivity and reduces agglomeration. The resulting composite anode exhibits impressive initial discharge capacity (2314.2 mAh g-1) and cycling stability (580.5 mAh g-1 over 50 cycles). This study provides a facile approach for next-generation anode materials.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, low friction coefficient, excellent optical properties, and extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a Ta/ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system, with tantalum (Ta) serving solely as a transition layer. Subsequently, Zr and Nb ions were implanted into the film at varying doses but with consistent energy levels. The analysis focused on the film's microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrated a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance.

The Shitouping pluton in Jiangxi Province, southern China, hosts an ion-adsorption heave rare earth element (HREE) deposit identified by recently geological survey. This study reveals the HREE pre-enrichment mechanism during the magma-hydrothermal process of granitic bedrock based on the comprehensive study of zircon structure and composition. Zircon from the Shitouping pluton, composed of syenogranite and monzogranite, can be categorized into three types based on structure and compositions. The Type-1 zircons, the predominate type in monzogranite granite, are early magmatic zircons with prismatic crystals and bright oscillatory zoning. In contrast, the late magmatic-hydrothermal zircons (Type-2 and Type-3) are mainly occurred in the syenogranite. The Type-2 zircons occur as murky euhedral crystals crystallized in the late magmatic stage. The Type-3 zircons with irregular zoning and abundant mineral inclu-sions in BSE images are closely associated with Type-2 zircons, possibly formed via intense hy-drothermal alteration during the hydrothermal stage. The increase in Y/Ho ratios from Type-1 to Type-3 zircon indicates that the Shitouping syenogranites underwent magmatic to hydrothermal evolution. Compared with Type-1 and Type-2 zircons, Type-3 zircons exhibit the highest con-centrations of F and HREEs. The significant increase of HREE concentrations both in zircons and bulk-rock composition of syenogranite can be attributed to the introduction of HREE-rich fluids during magma evolution. Under this condition, the HREEs mainly hosted in fluorocarbonates, which can easily release HREE3+ to generate ion-adsorption deposits during the weathering process. Therefore, we propose that increase of HREE contents in zircon reflect the exsolution of HREE-rich fluids during the magma evolution, which is important factor controlling HREE en-richment in Shitouping syenogranites and further generation of ion-adsorption HREE deposits.

The growing interest in Na-ion batteries as a “beyond lithium” technologies for energy storage drives the research for high-performance and environment-friendly materials. Na2Ti3O7 (NTO) as an eco-friendly, low-cost anode material shows a very low working potential of 0.3 V vs Na+/Na but suffers from poor cycling stability, which properties can be significantly influenced by materials synthesis and treatment. Thus, in this work, the influence of the calcination time on the electrochemical performance and the reaction mechanism during cycling were investigated. NTO heat-treated for 48 h at 800 °C (NTO-48h) demonstrated enhanced cycling performance in comparison to NTO heat-treated for only 8 h (NTO-8h). The pristine material was thoroughully characterized by X-ray diffraction, laser granulometry, X-ray photoelectron spectroscopy, and specific surface area measurements. The reaction mechanisms induced by sodiation/desodiation and cycling were investigated by opernado XRD. Electrochemical impedance spectroscopy was used to evidence the evolution of the solid electrolyte interface layer (SEI) and modification of charge transfer resistances as well as the influence of cycling on capacity decay. The evolution of the crystallographic structure of NTO-48h revealed a more ordered structure and lower surface contamination compared to NTO-8h. Moreover, the residual Na4Ti3O7 phase detected after the sodium extraction step in NTO-8h seems correlated to the lower electrochemical performance of NTO-8h compared to NTO-48h.

A CoCrFeNiNb0.65 eutectic high-entropy alloys (EHEAs) prepared by arc melting were irradiated with a 100 keV He+ ion beam. Swelling, helium bubbles and mechanical response induced by irradiation were evaluated. When the ion fluence reached 1.0×1018 ions/cm2, the irradiation-induced swelling occurred on the sample surface, and as the ion fluence increasing, the swelling became increasingly severe and the surface of Nb-rich phase appeared peeling and shedding. Meanwhile, along the boundaries of matrix and Nb-rich phase there was a neat line of helium bubbles. The size of these helium bubbles decreased with distance from the center of the helium bubble layer. This result indicated that the phase boundaries were favorable sites for the nucleation and gathering of helium bubbles. Nanoindentaion results indicated that hardening and softening induced by He+ ion irradiation occurred in various ion fluences. At ion fluence of 5.0×1017 ions/cm2, the CoCrFeNiNb0.65 EHEAs exhibited an obvious hardening behavior, which can be explained by dislocation-dominated hardening effect. When the ion fluence reached 1.0×1018 ions/cm2 and 2.0×1018 ions/cm2, the hardening effect decreased probably due to the helium bubble aggregation and growth, as well as helium bubbles induced noncompact structures. The results of this study provide insights into the effect of helium bubbles on mechanical evolution and pave the way for designing EHEAs suitable for the nuclear industry.

High surface area carbon was obtained from -carrageenan – urea cryogels doped with 1.25 – 5 wt% graphene oxide (GO). Incorporation of GO resulted in multifaceted modification in the textural and chemical properties of the carbon cryogel. The thermal decomposition of GO facilitated the formation of micropores resulted in a substantial increase in the apparent surface area (up to 1780 m2/g). The annealing at 1000 °C removed part of the heteroatoms but left behind a high number of defects. While the volatile thermal degradation products of GO affected the porous texture and the surface chemistry in a complex way, its reduced residue resulted in a gradually increasing electrical conductivity. The influence of GO was studied in oxygen reduction reaction (ORR) and in Li-ion storage application. GO affected the electron transfer mechanism in the ORR tests and challenged the stability of the electrodes. Even if the electrode has been stabilized under oxygen-free conditions, later may undergo destabilization processes during the ORR. The 5 wt% GO doped sample was the most sensitive under oxidative conditions, but finally it exhibited the highest capacitance. In the Li-ion battery tests the coulombic efficiency of all the samples was consistently above 98 %, indicating the great potential of such carbons for efficient Li-ion insertion and reinsertion during the charge – discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25% sample showed an initial discharge capacity of 313 mAh/g, 95.1 % capacity retention and 99.3 % coulombic efficiency after 50 charge – discharge cycles.

Silicon anodes have been considered one of the most promising anode candidates for the next generation of high-energy density lithium-ion batteries due to the high theoretical specific capacity (4200 mAh g-1) of Si. However, high lithiation capacity endows silicon anodes with severe volume expansion effects during the charge/discharge cycling. The repeated volume expansions not only lead to the pulverization of silicon particles and the separation of electrode materials from the current collector, but also brings rupture/formation of solid electrolyte interface (SEI) and also continuous electrolyte consumption, which seriously hinders the commercial application of silicon anodes. Structural design and optimization is the key to improving the electrochemical performances of silicon anodes, which has attracted wide attention and research in recent years. This paper mainly summarizes and compares the latest research progress for the structural design and optimization of silicon anodes.

Rechargeable aqueous Zn-ion batteries (ZIBs) have attracted considerable attention owing to their high theoretical capacity of 820 mA h g‒1, low cost and intrinsic safety. However, the electrolyte leakage and the instability issues of Zn negative electrodes originating from side reactions between the aqueous electrolyte and Zn negative electrode, not only restricts the battery stability but also results in short-circuit of aqueous ZIBs. Herein we report a flexible and stable N-isopropylacrylamide/sodium alginate (N-SA) gel electrolyte, which possesses high mechanical strength and high ionic conductivity of 2.96×10‒2 S cm‒1, and enables the Zn metal negative electrode and MnO2 positive electrode to reversibly and stably cycle. Compared to the liquid electrolyte, the N-SA hydrogel electrolyte can effectively form a uniform Zn deposition and suppress the generation of irreversible by-products. The assemble symmetric Zn/Zn cells at a current density of 1 mA cm‒2 shows a stable voltage profile, which maintains a low level of about 100 mV over 2600 h without an obvious short circuit or any overpotential increasing. Specially, the assembled Zn/N-SA/MnO2 batteries can deliver a high specific capacity of 182 mAh g‒1 and maintain 98% capacity retention after 650 cycles at 0.5 A g‒1. This work provides a facile method to fabricate high-performance SA-based hydrogel electrolytes that illustrates their potential for flexible batteries for wearable electronics.

The development of technology that combines supercapacitors and lithium-ion batteries by externally connecting them in parallel is ongoing. This study examines the correlation between the volume ratio and electrical characteristics of a cell made by internally connecting a battery capacitor with Li4Ti5O12 as the anode active material and a supercapacitor in parallel. It was found that increasing the volume occupied by the battery capacitor in the cell led to increased cell energy and resistance, resulting in decreased output characteristics. Conversely, increasing the volume occupied by the supercapacitor in the cell led to a decrease in the IR drop during discharge and cell temperature when evaluating cycle characteristics with a current of 20C. The study also examined the behavior of the current distributed during the charging and discharging process based on the volume ratio of the supercapacitor and the battery capacitor. Analyzing the correlation between the volume ratio and electrical characteristics of supercapacitors and battery capacitors could potentially lead to the development of a new type of energy storage device.

Silicon has a theoretical specific capacity of 4200 mAh g−1, which is considered to have significant potential for anode materials in lithium-ion batteries (LIBs). However, the volume change that occurs in silicon during charging and discharging affects the development of commercial applications. In this work, a yolk-shell structured Si@void@C anode material has been developed to address this problem. The silicon nanoparticle yolk material is obtained by recycling kerf-loss (KL) Si waste from the photovoltaic industry, the carbon shell is prepared via a hydrothermal process with glucose, and the sacrificial interlayer is Al2O3. The synthesized material is used to fabricate anodes that show a high reversible capacity of 836 mAh g−1 at the current density of 0.1 A g−1 after 100 cycles, with a Coulomb efficiency of 71.4%. This work demonstrates a relatively low-cost approach to turn KL Si waste into value-added materials for LIBs.

A non-steady state mathematical model of amino acid (phenylalanine (Phe)) and mineral salt (NaCl) solution separation by neutralization dialysis (ND) carried out in a batch mode is proposed. The model takes into account the characteristics of membranes (thickness, ion-exchange capacity and conductivity) and solutions (concentration, composition), as well as the flow rate of the solution in the dialyzer compartments. As compared to previously developed models, the new one considers the local equilibrium of Phe protolysis reactions in solutions and membranes and, also, the transport of all the phenylalanine forms (zwitterionic, positively and negatively charged) through membranes. A series of experiments on ND demineralization of NaCl and Phe mixed solution was carried out. In order to minimize Phe losses, the solution pH in the desalination compartment was controlled by changing the concentrations of the solutions in the acid and alkali compartments of the ND cell. The validity of the model was verified by comparison of simulated and experimental time dependencies of solution electric conductivity and pH, as well as the concentration of Na+, Cl– ions and Phe species in the desalination compartment. Based on the simulation results, the role of Phe transport mechanisms in the losses of this amino acid during ND was discussed.

Recent advances in synthetic membranes allow their use in fields as diverse as food and agriculture, biotechnology, industrial wastewater treatment, and potable water production. Among the newly developed technologies, nanofiltration for liquids and more particularly for desalination of seawater or saline aquifers are actively pursued. However, current solid-state membranes performance is limited, which calls for the development of novel formulations for membranes offering both high permeability (ion and water flux) and ion differentiation (selectivity), usually considered antagonist features. We report the development of hybrid nanoporous membranes made of solid-state polymeric carbonate track-etched (PCTE) thin films in which biological ion channels such as Gramicidin A (GA), alpha-hemolysin (α-HL), and outer-membrane protein F (OmpF) aquaporin are confined and graphene oxide (GO) conjugated cobalt ion selective binding peptide motifs (Copep) are adsorbed, referring as bioinspired and biomimetic approaches, respectively. These solid-state nanoporous membranes are attracting widespread attention since they offer scalability, mechanical robustness, selectivity, controlled pore dimension and shape, for water sustainability. The ion permeability, ion diffusion coefficient and selective ion recognition are evaluated via nanofiltration, cell diffusion kinetics, and UV-Visible absorption spectroscopy to gain insights into the role of key performance parameters including effective ion confinement in track-etched pores, rich surface chemistry, and peptide-induced channel for selective ion transport. These findings provide new avenues for artificial ion channels by synergistic combination of eco-friendly material design such as GO enabled by bio-molecular recognition chemistry.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

Recently, the interest in silicon-based detectors capable of detecting single photons in the near-infrared is growing mainly due to LiDAR applications, autonomous driving in particular. Silicon single-photon avalanche diodes are one of the most interesting single-photon NIR technology available on the market, nevertheless, their efficiency is hindered by the low absorption coefficient of Si in the NIR. The idea is the integration of CMOS-compatible nanostructures, specifically, silver grating array supporting Surface Plasmons Polaritons (SPPs), to confine superficially the incoming NIR photons and therefore increase photons probability to generate an electron-hole pair. The plasmonic silver array is geometrically fine-tuned using time domain simulation software to achieve maximum detector performance at 950 nm. Then, the plasmonic silver array is integrated by means of the focused ion beam technique on the detector. Finally, the integrated detector is electro-optically characterized, demonstrating a quantum efficiency of 13 at 950 nm, 2,2 times more than the reference detector. This result suggests the production of a device capable of detecting single NIR photons, at a very low cost and compatible with CMOS, thus integrable on existing technology platforms.

We present a critical analysis of the mechanism of reversible hydrogen evolution reaction based on thermodynamics of hydrogen processes considering atomic and ionic species as intermediates. Clear distinction between molecular hydrogen evolution/oxidation (H$_2$ER and H$_2$OR) and atomic hydrogen evolution/oxidation (HER and HOR) reactions is made. It is suggested that the main reaction describing reversible H$_2$ER and H$_2$OR in acidic and basic solutions is: $\ce{H3O^+} + 2e^- \xrightleftharpoons{\mathrm{({H}_{2}^{+}})_{ad}} \ce{H2} + \ce{OH^-}$, which proceeds via the formation of hydrogen molecular ion as intermediate and its potential is $E^{0}$ = 0.414~V (at the standard Hydrogen electrode SHE scale). We analyse experimentally reported data with models which provide \emph{quantitative} match (R.J.Kriek et al., Electrochem. Sci. Adv. e2100041 (2021)). The experimentally observed slope of $\lg(Current)$ vs. $Potential$ equal to $\approx 30$~mV/dec corroborates the presented model of H$_2$ER/H$_2$ER based on \ce{H2$^+$} as intermediate.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

Salinity is a serious environmental hazard which limits world agricultural production by adversely affects plant physiology and biochemistry. Hence increase tolerance against salt stress is very important. In this study, we explored the function of β-aminobutyric acid (BABA) in enhancing salt stress tolerance in rapeseed (Brassica napus L.). After pretreatment with BABA, seedlings were exposed to NaCl (100 mM and 150 mM) for 2 days. Salt stress increased Na content and decreased K content in shoot and root. It disrupted the antioxidant defense system by producing reactive oxygen species (ROS; H2O2 and O2•−), methylglyoxal (MG) content and causing oxidative stress. It also reduced the growth and photosynthetic pigments of seedlings but increased proline (Pro) content. However, BABA pretreatment in salt-stressed seedlings increased ascorbate (AsA) and glutathione (GSH) contents; GSH/GSSG ratio; and the activities of ascorbate peroxidase (APX), monodehydroascorbate reductase (MDHAR), dehydroascorbate reductase (DHAR), glutathione reductase (GR), glutathione peroxidase (GPX), superoxide dismutase (SOD), catalase (CAT), glyoxalase I (Gly I), and glyoxalase II (Gly II) as well as growth and photosynthetic pigments of plants. In addition, compared to salt stress alone BABA increased Pro content, reduced the H2O2, MDA and MG contents and decreased Na content in root and increased K content in shoot and root of rapeseed seedlings.

An ion exchange dialysis (IED) is used in the recovery of aluminium from residue. In this papers, the face-centered central composite design (FC-CCD) of the response surface methodology (RSM) and desirability approach is used for experimental design, modelling and process optimization of a counter flow IED system. The feed concentration, feed flowrate, sweep flowrate and sweep concentration are selected as the process variables, with the Al-transport across a Nafion 117 membrane as the target response. A total of 30 experimental runs were conducted with 6 center points. The response obtained was analysed by analysis of variance (ANOVA) and fitted to a second-order polynomial model using multiple regression analysis. The actual R2 and standard deviation of the model are 0.9548 and 0.2932 respectively. The influences of significant variables are plotted on 3D surface and contour plots. The designed variables were numerically optimized by applying the desirability function to achieve the maximum Al-transport. The optimised condition values were found to be feed concentration (1600 ppm), feed flowrate (61.76%), sweep flowrate (37.50%) and sweep concentration (0.75 N) for the 80% target response at 32hrs. Overall, the model can be used to effectively predict Al-recovery using the designed system

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

A new type of gold nanoparticles was synthesized by using benzoyl pyrazolone as a capping agent. The synthesized AuNPs exhibited a spherical shape and a monodisperse and fluorescence emission characteristic peak at 650 nm. The AuNPs –BMPBP was demonstrated as sensitive and selective fluorescent chemosensor for detection of Al ³⁺ ion. In the presence of Al ³⁺ ion, the fluorescent emission of BMPBP-AuNPs at 650 nm, increased with an increasing concentration of Al ³⁺ ion with a low detection limit (2 µM), the proposed method provided to apply determination of Al ³⁺ ion of tap water with satisfactory results.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

Elevated blood glucose levels, known as glycemia, play a significant role in sudden cardiac arrest, often resulting in sudden cardiac death, particularly among those with diabetes. Understanding this link has been a challenge for healthcare professionals, leading many research groups to investigate the relationship between blood glucose levels and cardiac electrical activity. Our hypothesis suggests that glucose-sensing mechanisms in cardiac tissue could clarify this connection. To explore this, we adapted a single-compartment, in-silico model of the human atrial node's action potential. We incorporated glucose-sensing mechanisms with voltage-gated sodium ion channels using ordinary differential equations. Parameters for the model were based on existing experimental studies to mimic the impact of glucose levels on atrial node action potential firing. Simulations using voltage clamp and current clamp techniques showed that elevated glucose levels decreased sodium ion channel currents, leading to a reduction in the sinoatrial node action potential frequency. In summary, our model provides a cellular-level understanding of how high glucose levels can lead to bradycardia and sudden cardiac death.

Malaria parasites increase their host erythrocyte’s permeability to obtain essential nutrients from plasma and facilitate intracellular growth. In the human P. falciparum pathogen, this increase is mediated by the plasmodial surface anion channel (PSAC) and has been linked to CLAG3, as encoded by one member of the conserved clag multigene family. Whether paralogs encoded by other clag genes also contribute to PSAC formation or serve unrelated roles remains unknown. Here, we generated transfectant lines carrying epitope-tagged versions of each CLAG. Each paralog colocalized with CLAG3, with concordant trafficking via merozoite rhoptries to the host erythrocyte membrane of newly-invaded erythrocytes. Each also exists within infected cells in at least two forms: an alkaline-extractable soluble form and a form integral to the host membrane. Like CLAG3, CLAG2 has a variant region cleaved by extracellular protease but CLAG8 and CLAG9 are protease-resistant. Paralog knockout lines, generated through CRISPR/Cas9 transfection, exhibited uncompromised growth in PGIM, a modified medium with more physiological nutrient levels; this finding is in marked contrast to a recently reported CLAG3 knockout parasite. CLAG2 and CLAG8 knockout lines exhibited compensatory increases in transcription of remaining clags and associated rhoph genes, yielding increased PSAC-mediated uptake to specific solutes. We also report distinct transport properties of these knockout lines, suggesting partially overlapping roles of CLAG paralogs in PSAC activity. We propose that the nutrient channel pore is formed by a higher order assembly of CLAG proteins at the host membrane.

Though nowadays germanium do not reach the range of popularity than other metals, i.e. rare earth elements, its utility in target industries makes of it also a strategic metal. Though germanium can be find in a series of raw materials, the principal source for its recovery is from secondary wastes of the zinc industry, and also, the recycle of germanium-bearing waste materials is becoming of interest. In this recovery, Hydrometallurgy is performing a key role to the successful achievement of this goal. The present work reviews the most recent applications (2023 and 2024 years) of hydrometallurgical operations on the recovery of germanium from different solid and liquid sources.

As the global transition towards renewable energy accelerates, the integration of grid-scale energy storage systems has become increasingly critical for stabilizing energy supply and enhancing grid reliability. Among various storage technologies, lithium-ion batteries stand out for their high energy density, scalability, and relatively low environmental impact. This study investigates the performance and longevity of lithium-ion batteries in grid-scale applications, focusing on the impact of operational parameters such as cycling frequency, depth of discharge, temperature fluctuations, and charging/discharging rates. Employing a mixed-methods approach, we combined quantitative analysis of performance metrics (cycle life, capacity fade, efficiency) with qualitative assessments from case studies of existing grid-scale projects. Our findings reveal that while lithium-ion batteries exhibit robust performance in grid-scale storage, their longevity and efficiency are significantly influenced by operational conditions. Specifically, temperature management and optimized cycling strategies were identified as key factors in mitigating degradation and extending battery life. This research provides a comprehensive understanding of lithium-ion battery behavior in grid-scale environments, offering valuable insights for the design, optimization, and management of energy storage systems. By addressing the challenges of battery performance and longevity, our study contributes to the development of more sustainable and reliable grid storage solutions, facilitating the broader adoption of renewable energy sources.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

The ubiquitous deployment of Li-ion batteries (LIBs) in more demanding applications has reinforced the need to understand root-causes of thermal runaway. Herein we perform a forensic simulation of a real-case failure scenario, using localised heating of Li(Ni0.5Mn0.3Co0.2)O2 versus graphite 18650 cylindrical cells. This study determined the localised temperatures that would lead to venting and thermal runaway of these cells, as well as correlating the gases produced as a function of degradation pathway. Catastrophic failure, involving melting (with internal cell temperatures exceeding 1085°C), deformation and ejection of cell componentry, was induced by locally applying 200 °C and 250 °C to a fully charged cell. Conversely, catastrophic failure was not observed when the same temperatures were applied to the cells at lower state of charge (SOC). This work highlights the importance of SOC, chemistry and heat in driving the thermal failure mode of Ni-rich LIB cells, allowing for a better understanding of battery safety and associated design improvements.

Human RAD51 protein (HsRad51)-promoted DNA strand exchange, a crucial step in homologous recombination, is regulated by proteins and calcium ions. The activator protein Swi5-Sfr1 and Ca2+ ions stimulate different reaction steps and induce a perpendicular orientation of DNA bases in the presynaptic complex. To investigate the importance of base orientation in the strand exchange reaction, we examined the Ca2+ concentration dependence of strand exchange activities and structural changes in the presynaptic complex. Our results show that optimal D-loop formation (strand exchange with closed circular DNA) requires Ca2+ concentrations greater than 5 mM, while 1 mM is sufficient for strand exchange between two oligonucleotides. The structural change, which is evidenced by an increase in fluorescence intensity of poly(dεA) (a poly(dA) analog), reaches a plateau at 1 mM Ca2+. Meanwhile, the linear dichroism signal intensity at 260 nm, which is indicative of rigid perpendicular DNA base orientation, requires >2 mM Ca2+ for saturation and thus correlates with the stimulation of D-loop formation. Therefore, Ca2+ exerts two different effects. Thermal stability measurements suggest that HsRad51 binds two Ca2+ ions with KD values of 0.3 mM and 2.5 mM, implying that one step is stimulated by one Ca2+ bond and the other by two Ca2+ bonds. We further discuss the parallels between Mg2+ activation of RecA and Ca2+ activation of HsRad51.

Transportation is the primary consumer of oil, accounting for a significant portion of global energy consumption (34%) and CO2 emissions (40%). Electrifying road transportation is crucial to mitigate the effects of global warming. The abundant potential of renewable energy sources like solar and wind is hindered by their intermittent nature and incongruity with peak energy demands. This calls for the development of sophisticated energy storage solutions. Metal-air batteries (MABs), emerging as viable alternatives to lithium-ion batteries (LIBs), have attracted considerable attention due to their promising applications in the transportation sector. Despite substantial progress in MAB development over the past two decades, overcoming critical challenges such as electrolyte decomposition, carbon cathode degradation, anodic dendrite growth, and air impurities remains essential for their commercial viability. This mini-review provides a comprehensive overview of MAB fundamentals and the challenges associated with their development. The insights presented in this review serve to illuminate the current landscape and future prospects of MABs in the transportation sector.