This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

Background: Low-level (LLLT) and high-intensity laser therapy (HILT) can be beneficial additions to knee osteoarthritis (KOA) rehabilitation exercises; however, it is still being determined which modality is more effective. Aim: To compare the effects of LLLT and HILT as adjuncts to rehabilitation exercise (LL+EX and HL+EX) on clinical outcomes in KOA. Methods: Thirty-four adults with mild to moderate KOA were randomly allocated to either LL+EX (n = 17) or HL+EX (n = 17) groups. All participants underwent their designated laser treatment combined with rehabilitation exercises weekly for twelve consecutive weeks. The Knee Injury and Osteoarthritis Outcome Score (KOOS), Numerical Pain Rating Scale (NPRS), active knee flexion, and Timed Up-and-Go test (TUG) were assessed at baseline and immediately post-intervention. Results: Post-intervention, both groups significantly improved their KOOS, NPRS, active knee flexion, and TUG scores compared to baseline (p < 0.01). The mean difference of change in KOOS, NPRS, and active knee flexion scores for the HL+EX group surpassed the minimal clinically important difference threshold. In contrast, the LL+EX group only demonstrated clinical significance in NPRS scores. Conclusions: Incorporating HILT as an adjunct to usual KOA rehabilitation led to significantly higher improvements in pain, physical function, and knee-related disability compared to LLLT.

High-Intensity Functional Training (HIFT) is a novel exercise intervention that may test body systems in a balanced and integrated fashion by challenging individuals’ abilities to complete mechanical work. However, research has not previously determined if physical work capacity is unique to traditional physiologic measures of fitness. Twenty-five healthy men and women completed a six-week HIFT intervention with physical work capacity and various physiologic measures of fitness assessed pre- and post-intervention. At baseline, these physiologic measures of fitness (e.g., aerobic capacity) were significantly associated with physical work capacity and this relationship was even stronger at post-intervention assessment. Further, there were significant improvements across these physiologic measures in response to the delivered intervention. However, the change in these physiologic measures failed to predict the change in physical work capacity induced via HIFT. These findings point to the potential utility of HIFT as a unique challenge to individuals’ physiology beyond traditional resistance or aerobic training. Elucidating the translational impact of increasing work capacity via HIFT may be of great interest to health and fitness practitioners ranging from strength/conditioning coaches to physical therapists.

Purpose: This study investigates the impact of different intensity normalization (IN) methods on the overall survival (OS) radiomics models’ performance of MR sequences in primary (pHGG) and recurrent high-grade glioma (rHGG). Methods: MR scans acquired before radiotherapy were retrieved from two independent cohorts (rHGG C1: 197, pHGG C2: 141) from multiple scanners (15, 14). The sequences are T1 weighted (w), contrast-enhanced T1w (T1wce), T2w, and T2w-FLAIR. Sequence-specific significant features (SF) associated with OS, extracted from the tumour volume, were derived after applying 15 different IN methods. Survival analyses were conducted using Cox proportional hazard (CPH) and Poisson regression (POI) models. A ranking score was assigned based on the 10-fold cross-validated (CV) concordance index (C-I), mean square error (MSE), and the Akaike information criterion (AICs), to evaluate the methods’ performance. Results: Scatter plots of the 10-CV C-I and MSE against the AIC showed an impact on the survival predictions between the IN methods and MR sequences (C1/C2 C-I range: 0.62-0.71/0.61-0.72, MSE range: 0.20-0.42/0.13-0.22). White stripe showed stable results for T1wce (C1/C2 C-I: 0.71/0.65, MSE: 0.21/0.14). Combat (0.68/0.62, 0.22/0.15) and histogram matching (HM, 0.67/0.64, 0.22/0.15) showed consistent prediction results for T2w models. They were also the top-performing methods for T1w in C2 (Combat: 0.67, 0.13; HM: 0.67, 0.13), however, only HM achieved high predictions in C1 (0.66, 0.22). After eliminating IN impacted SF using Spearman’s rank-order correlation coefficient, a mean decrease in the C-I and MSE of 0.05 and 0.03 was observed in all four sequences. Conclusion: The IN method impacted the predictive power of survival models. Thus, performance is sequence-dependent.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Objective: To study the changes in urine metabolism in female water polo players before and after high-intensity training by using ultra-high performance liquid chromatography-mass spectrometry, and to explore the biometabolic characteristics of urine after training and competition. Methods: Twelve young female water polo players (except goalkeepers) from Shanxi Province were selected. A 4-week formal training was started after one week of acclimatization according to experimental requirements. Urine samples (5 ml) were collected before formal training, early morning after 4 weeks of training, and immediately after 4 weeks of training matches, and labeled as T1, T2, and T3, respectively. The samples were tested by LC-MS after pre-treatment. XCMS, SIMCA-P 14.1, and SPSS16.0 were used to process the data and identify differential metabolites. Results: On comparing the immediate post-competition period with the pre-training period (T3 vs T1), 24 differential metabolites involved in 16 metabolic pathways were identified, among which niacin and niacinamide metabolism and purine metabolism were potential post-competition urinary metabolic pathways in the untrained state of the athletes. On comparing the immediate post-competition period with the post-training period (T3 vs T2), 10 metabolites involved in 3 metabolic pathways were identified, among which niacin and niacinamide metabolism was a potential target urinary metabolic pathway for the athletes after training. Niacinamide, 1-methylnicotinamide, 2-pyridone, L-Gln, AMP, and Hx were involved in two metabolic pathways before and after the training. Conclusion: Differential changes in urine after water polo games are due changes in the metabolic pathways of niacin and niacinamide.

The purpose of this study was to assess if self-regulation of intensity based on rating of perceived exertion (RPE) is a reliable method to control the intensity of metabolic conditioning of functional-fitness session. In addition, the relationship between RPE and changes in heart rate and lactate responses was also analyzed. Eight male participants (age 28.1 ± 5.4 years; body mass 77.2 ± 4.4kg; VO₂max: 52.6 ± 4.6 mL·(kg·min)⁻¹) completed three randomly sessions (5 to 7 days apart) under different conditions: (1) all-out (ALL); (2) self-regulation of intensity based on a RPE of 6 (hard) on the Borg CR-10 scale (RPE6); and (3) a control session. Rate of perceived exertion, LAC and HR response were measured pre, during and immediately after the sessions. The RPE and LAC during the ALL-OUT sessions were higher (p ≤ 0.05) than the RPE6 and control sessions for all the analyzed time points during the sessions. Regarding HR, the 22 min area under the curve of HR during ALL-OUT and RPE6 sessions were significantly higher (p ≤ 0.05) than the control session. The average number of repetitions was lower (p ≤ 0.05) for the RPE6 session (190.5 ± 12.5 repetitions) when compared to the ALL session (214.4 ± 18.6 repetitions). There was a significant correlation between RPE and LAC (p = 0.001; r = 0.76; very large) and number of repetitions during the session (p = 0.026; r = 0.55; large). No correlation was observed between RPE and HR (p = 0.147; r = 0.380). These results indicate that self-regulation of intensity of effort based on RPE may be a useful tool to control exercise intensity during a metabolic conditioning session of functional-fitness.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.

The purpose of the present study was to compare heart rate (HR), blood lactate and training load between different CrossFit® workouts, with equalized total volume in men and women. The study included 23 individuals (13 men and 10 women) experienced in CrossFit® training, who performed two workouts with different training types (as many reps as possible - AMRAP and for time) but equalized volume. Measurements of lactate, HR and rating of perceived exertion (RPE) were performed. The results showed that there was no HR interaction between workout time and sex (p = 0.822; η2 = 0.006] and between workout type and sex (p = 0.064, η2 = 0.803). HR significantly differed during each workout type (p <0.001, η2 = 0.621), but not between the two workout types (p = 0.552, η2 = 0.017). Lactate showed no difference between the workout types (p = 0.474, η2 = 0.768), although the training load was higher (p = 0.033, η2 = 0.199) in women when they performed AMRAP. Altogether, HR was not significantly different between training types or sex, while RPE, lactate and training load showed small differences depending on the group (women or men) or workout type (AMRAP or 'for time').

An experimental platform for laser-driven ion (sub-MeV) acceleration and potential applications was recently commissioned at the HiLASE laser facility. The auxiliary beam of the Bivoj laser system operating at GW peak power (~10 J in 5-10 ns) and 1-10 Hz repetition rate enabled a sta-ble production of high-current ion beams of multiple species (Al, Ti, Fe, Si, Cu, Sn). The pro-duced laser-plasma ion sources were fully characterized against the laser intensity on target (1013-1015 W/cm2) by varying the laser energy, focal spot size, and pulse duration. This al-lowed to provide accurate scaling laws of the maximum ion energy for the different target ma-terials investigated. Such experimental scaling laws are presented for the first time in the inves-tigated laser intensity range and for ns-class laser pulses, and allow to provide a qualitative in-terpretation of the laser-plasma interaction underpinning physics, thus to tune the main features of the accelerated ion beams (energy, temperature, and current). Such a detailed study was facil-itated by the large amount of data acquired at high repetition rate (1-10 Hz) provided by the Bivoj laser system. The versatility and tuneability of such high-repetition-rate laser-plasma ion sources are of po-tential interest for multidisciplinary user applications.

The study describes the acute and delayed time course of recovery following the CrossFit® Benchmark Workout Karen. Eight trained men (28.4±6.4 years; 1RM back squat 139.1±26.0 kg) undertook the Karen protocol. The protocol consists of 150 Wall Balls, aiming to hit a target 3 meters high. Countermovement jump height (CMJ), creatine kinase (CK), and perceived recovery status scale (PRS) (general, lower and upper limbs) were assessed pre, post-0h, 24h, 48h and 72h after the session. The CK concentration 24h after was higher than pre-exercise (338.4 U/L vs. 143.3 U/L; effect size: 0.74; p≤0.05). At 48h and 72h following exercise, CK concentration had returned to baseline levels. The PRS general and of the lower limbs were lower in the 24-hours post-exercise compared to pre-exercise (PRS general: 4.7 ±1.5 and 7.9 ±1.7 mmol/L; and PRS of the lower limbs: 4.0 ±2.5 and 7.9 ±0.8, respectively). The PRS general, lower, and upper limbs were reduced at 48-post exercise compared to 72-hours post-exercise scores. Our findings provide insights into the fatigue profile and recovery in acute CrossFit® and can be useful to coaches effectively design the daily session.

Hypertension is one of the most common primary cardiometabolic diseases and is a major contributor to cardiac mortality and morbidity. Furthermore, cardiac risk factors such as obesity and sedentary lifestyle are often seen in hypertensive patients. Regular exercise acts against these risk factors and improves the overall health of an individual. High-intensity interval training appears to do so in a more efficient way. We used a systematic literature review (SLR) approach to provide an overview of the present literature highlighting the cardiovascular advantages of HIIT in hypertensive individuals. We reviewed 4004 articles from reputable journals published between 2013 and August 14, 2023, focusing on 7 selected papers for in-depth analysis. This systematic review revealed the protective effects of HIIT against cardiac complications in hypertension. All the reviewed articles showed a decrease in blood pressure and many other risk variables of cardiovascular diseases. However, guidelines for this exercise are needed for maximum benefits. Therefore, further research on HIIT is necessary to fully harness its potential.

The temperature-assisted laser shock process has shown promising prospects in the fields of forming manufacturing and surface strengthening. However, large-scale application of this process is limited by the instability and failure of confinement medium at high temperatures (≥300 ℃). Aiming at this problem, we propose a novel laser shock strategy based on Leidenfrost effect, where the suspended droplets are utilized as the confinement medium. According to the sequence of images acquired by time delay system and high-speed camera, the droplet dynamics behavior is studied. The focusing enhancement effect of the droplet is comprehensively explored. And the correlations between droplet size, ambient temperature, vapor layer thickness and focusing effect are investigated. Combining the dynamics and focusing enhancement effect of droplets, a theoretical model of laser shock pressure under droplet confinement is established. Finally, the effectiveness and feasibility of the droplet-based laser shock strategy in high temperature processing environments are verified by typical applications in laser shock forming and laser shock peening fields. The results show that the droplet-based laser shock process presents better forming effect. And the mechanical property tests demonstrate that this process can obtain the simultaneous improvement of the strength (~51%) and ductility (~6.4%) of annealed Cu. The multiscale plasticity mechanisms of the strengthened material are comprehensively investigated. We believe that this low-energy, low-cost and high-quality process can provide a new solution for the industrial application of laser shock at high temperatures.

This paper presents the design and experimental results of a long cavity length Nd: YAG laser with large stable zone for water jet guided laser (WJGL) applications. The design is based on the light transmission matrix and resonator stability conditions, aiming to achieve a large stable zone and a short cut-off thermal focal length (CTFL). A folded concave resonator is researched to enhance the cavity length, and the influence of the tun-able cavity arm length on the oscillating beam in the resonator and in the YAG crystal is theoretically studied. Moreover, the effects of the output mirror curvature and the cavity arm length on the range of the stable area and the cut-off thermal focal length are also investigated. Experimental results show that a stable green laser output is obtained after second harmonic generation (SHG), with a pulse width ranging from 43ns to 143ns within the laser operating frequency range of 5-20kHz. At an operation frequency of 10kHz, the output power is 21.33W, and the instability of the output power within 400 minutes is 0.88%. The laser source achieves a maximum power of 25.7W at 20kHz, and the maximum single pulse energy reaches 2.7mJ at 6kHz. Finally, this is used as the laser source to couple with a water jet with a diameter of 100 microns, achieving a lossless water conductivity transmission over 60mm length with a peak power density of 0.742GW/cm2. These results demonstrate the suitability of the designed laser source for WJGL technology research.

Drought-induced plant mortality has increased globally during the last decades and is forecasted to influence global vegetation dynamics. Timely information on plant water dynamics is essential for understanding and anticipating drought-induced plant mortality. The most common metric that has been used for decades for measuring water stress is leaf water potential (Ψ_L), which is measured destructively. To obtain information on water dynamics from trees and forested landscapes, remote sensing methods have been developed. However, the spatial and temporal resolution of the existing methods have limited our understanding of water dynamics and diurnal variation of Ψ_L within single trees. Thus, we investigated the capability of terrestrial laser scanning (TLS) intensity in observing diurnal variation in Ψ_L during a 50 hour monitoring period and aimed to improve understanding on how large part of the diurnal variation in Ψ_L can be captured using intensity observations. We found that TLS intensity at 905 nm wavelength was able to explain 78% of the variation in Ψ_L for three trees of two tree species with a root-mean square error of 0.137 MPa. Based on our experiment with three trees, time-series of TLS intensity measurements can be used in detecting changes in Ψ_L, and thus it is worthwhile to expand the investigations to cover a wider range of tree species and forests and further increase our understanding of plant water dynamics at wider spatial and temporal scales.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

Type 1 diabetes (T1D) is associated with hyperglycaemia-induced hypoxia and inflammation. The study assessed the effects of a single high-intensity interval exercise (HIIE) on glycaemia (BG) and serum level of pro-inflammatory cytokines and an essential mediator of adaptive response to hypoxia in T1D patients. The macronutrients intake was also evaluated. Nine patients suffering from T1D for about 12 years and nine healthy individuals (CG) were enrolled and completed one session of HIIE at the intensity of 120% lactate threshold and duration of 4 x 5 min intermittent with 5 min rest after each bout of exercise. Capillary and venous blood was withdrawn at rest, immediately after and at the 24 h post-HIIE for analysis of BG, hypoxia-inducible factor alpha (HIF-1α), tumour necrosis factor alpha (TNF-α) and vascular-endothelial growth factor (VEGF). Pre-exercise BG was significantly higher in the T1D compared to the CG (p = 0.043). HIIE led to a significant decline in T1D patients’ BG (p = 0.027) and to a tendency for a lower BG at 24-h post-HIIE vs pre-HIIE. HIF-1α was significantly elevated in the T1D compared to CG and there was a trend for HIF-1α to decline, and VEGF, TNF-α to increase in response to HIIE in the T1D group. Both groups consumed higher and lower than recommended amounts of protein and fat, respectively. In T1D group, a tendency for a higher digestible carbohydrate intake and more frequent hyperglycaemic episodes on the day after HIIE were observed. HIIE was effective in reducing T1D patients’ glycaemia and improving the short-term glycaemic control. HIIE has the potential to improve adaptive response to hypoxia by elevating the serum level of VEGF. Patients’ diet and level of physical activity should be screened on a regular basis, and they should be educated on the glycaemic effects of digestible carbohydrates.

Knee osteoarthritis (OA) is the most common joint disease worldwide. Exercise therapy has been identified as a first-line treatment option in patients suffering from knee OA. High-intensity interval training (HIIT) is an innovative exercise modality with potential in improving various disease-related outcomes. The purpose of this review is to explore the impact of HIIT on knee OA symptoms and physical functioning. A comprehensive search of scientific electronic databases was conducted to identify the articles on the effects of HIIT on knee OA. Thirteen studies were included in this review. Nine compared the effects of HIIT with those of low-intensity training, moderate-intensity continuous training, or a control group. Three evaluated the effects of HIIT alone. Eight reported a decrease in knee OA symptoms, and eight reported an increase in physical functioning. HIIT was shown to improve knee OA symptoms and physical functioning, but also aerobic capacity, muscle strength, and quality of life with minimal or no adverse events. However, compared to other exercise modalities, no clear superiority of HIIT was found. HIIT is a promising exercise strategy in patients with knee OA: anyway, the actual quality of evidence remains very low, and more high-quality studies are needed to confirm these promising outcomes.

This paper presents the automation of the thin-layer chromatography technique whose separation and identification of molecules present in a mixture are currently done manually and laboriously [1]. We have therefore found an interest in automating this technique. In this part, the method implemented comprises 2 steps. First we proceeded to the segmentation of the spots obtained on the chromatographic plate. We then developed a program to identify families of molecules such as coumarins, terpenes, tannins, flavonoids, polyphenols, etc. by calculating segmentation parameters such as standard deviation, entropy, average pixel intensity from an algorithm on the matlab software. Finally our results have been compared to the results obtained by the traditional identification technique in laboratories. Some similarity between the two results obtained shows the reliability and the robustness of our technique.

Ultra-short laser pulses (1030 nm/230 fs) were used to laser ablate surface of crystalline sapphire. Laser ablated patterns were annealed at high temperature 1500∘C. Surface reconstruction took place removing ablation debris field at the edges of ablated pits in oxygen flow. Partial reconstruction of ripples was also observed.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

The aeroelastic response of lightweight low-speed aircraft with slender wings under extreme flow turbulence intensity is not well-understood. Experiments on a commmercial unmanned aerial vehicle (UAV) with a 3-meter wingspan and aspect ratio of 13.6 were performed in a large open-return wind tunnel with extreme flow turbulence intensity of T∞≈10%. The structural dynamics of the wing in the bending mode and the flow beneath the wing to capture the effect of aileron deflection was measured using laser displacement sensors and tomographic particle image velocimetry (PIV) techniques. The unsteady lift produced by the wing was also measured using a high-capacity load cell at an angle of attack, α of 2 degrees for three freestream velocities U∞ of 13.4 m/s, 17.9 m/s, and 26.8 m/s representing the UAV’s stall through cruise speed. It was found that high flow turbulence intensity with large integral length scales relative to the wing chord plays a dominant role in the large unsteady lift and wing displacements measured. The power spectral density (PSD) of wing structural vibration shows that flow shedding from the wing and the integral length scales have a significant impact on the overall power inherent in the bending vibration of the wing. Computation of vorticity iso-surfaces in the flow measurement volume surrounding the aileron reveal a striking observation; aileron deflection, δa of 10∘becomes less effective in producing additional spanwise vorticity, which is proportional to circulation and lift, at U∞ of 26.8 m/s because the freestream already has elevated levels of vorticity. A paradigm shift in design is suggested for light aircraft structures with slender wings operating in highly turbulent flow, which is to employ multiple control surfaces in order to respond to this flow and mitigate large bending or torsion displacements and the probability of structural failure.

To create normative scores for all CrossFit® Open (CFO) workouts and compare male and female performances, official scores were collected from the official competition leaderboard for all competitors of the 2011-2022 CFO competitions. Percentiles were calculated in athletes (18 – 54 years) who completed all workouts within a single year ‘as prescribed’ and met minimum scoring thresholds. Independent t-tests revealed significant (p &lt; 0.05) sex differences for 56 of 60 workouts. In workouts scored by repetitions completed, men completed more repetitions in 18 workouts by small-to-large differences (d = 0.22-0.81), whereas women completed more repetitions in 6 workouts by small-to-medium differences (d = 0.36-0.77). When workouts were scored by time-to-completion, men were faster in 10 workouts by small-to-large differences (d = 0.23-1.12), while women were faster in three workouts by small differences (d = 0.46). In three workouts scored by load lifted, men lifted more weight by large differences (d = 2.00-2.98). All other differences were either trivial or not significant. Despite adjusted programming for men and women, the persistence of performances differences across all CFO workouts suggest resultant challenges are not the same. These normative values may be useful to training and research in male and female CrossFit® athletes.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

A pilot study on laser 3D printing of inorganic free-form micro-optics is experimentally validated. Ultrafast laser nanolithography is employed for structuring hybrid organic-inorganic material SZ2080TM followed by high-temperature calcination post-processing. The combination allows production of 3D architectures and the heat-treatment results in converting the material to inorganic substance. The produced miniature optical elements are characterized and their optical performance demonstrated. Finally, the concept is validated for manufacturing compound optical components such as stacked lenses. This is opening for new directions and applications of laser made microoptics under harsh conditions such as high intensity radiation, temperature, acidic environment, pressure variations, which include open space, astrophotonics, and remote sensing.

The valley pseudospin properties of electrons in two–dimensional hexagonal materials result in lots of fascinating physical phenomena, which opens up the new field of valleytronics. The valley-contrasting physics aims at distinguishing the valley degree of freedom based on valley–dependent effects. Here, we theoretically demonstrate that both of the valley–selective high harmonic generation and valley–selective electronic excitation can be achieved by using an orthogonal two–color (OTC) laser field in gapped graphene. It is shown that the asymmetry degrees of harmonic yields in the plateaus, cutoff energies of generated harmonics and electron populations from two different valleys can be precisely controlled by the relative phase of the OTC laser field. Thus the selectivity of the dominant valley for the harmonic radiation and electronic polarization can be switched by adjusting the relative phase of the OTC laser field. Our work offers an all–optical route to produce the valley–resolved high harmonic emissions and manipulate the ultrafast valley polarization on a femtosecond timescale in condensed matter.

Obesity is linked to an inflammatory process, with adipocyte release triggering insulin resistance (IR) and autonomic imbalance. A cardiovagal trainning protocol has shown favorable results in autonomic balance and decrease of inflammatory markers. The aim of this study was to analyze the autonomic behavior related to inflammatory and metabolic parameters in obese people after a cardiovagal exercise protocol. Twenty people with obesity, were distributed by their HOMA-IR value: obese without IR (n/IR) (n=8) and obese with IR (y/IR) (n=12). The cardiovagal training program was carried out in both groups for 8 weeks at a frequency of 5 times per week. A blood sample was obtained to determine insulin, leptin, TNF alpha and IL6 levels, in addition to determining the HOMA-IR index and autonomic function was measured by heart rate variability. Changes were recorded in the OB-IR group, a decrease in inflammatory markers, glycemia and a reduction of sympathetic activity after the cardiovagal training intervention. In addition, significant differences between the y/IR and n/IR groups were shown in insulin, leptin, TNFa and IL6 values. It can be concluded that after 4 weeks of intervention with a cardiovagal trainning protocol, parasympathetic modulation increased and inflammatory markers decreased in obese subjects.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

China is rich in coal resources under water bodies. However, for a long time, the safety prediction of high-intensity mining under water bodies is one of the problems encountered by the coal industry. It is of great significance to realize safe mining under water bodies, improve the recovery rate of coal resources and protect reservoir resources. Therefore, this article takes the No. 5 coal seam and No. 11 mining area of Wangwa Coal Mine as the research object, and integrates physical simulation, numerical simulation, theoretical analysis and other methods to study the development height of water-conducting fracture zones in fully mechanized top coal caving mining. Solid-liquid coupling physical simulation test reveals the failure characteristics of overlying strata in goaf and the seepage law of reservoir water under the influence of mining. By comparing the monitoring data of borehole leakage, the measured data obtained by borehole peeping with the height data of water-conducting fracture zone obtained by the traditional empirical formula of three-under standard, the error between the two is as high as -29.39 %. In this case, the variance correction coefficient is used to correct the empirical formula, and on this basis, in order to effectively protect the surface water dam and water body, the mining height of coal seam in the working face with limited height mining is inversely derived. The research results provide a basis for the safety prediction of high-intensity mining under the reservoir dam in the ecologically fragile areas of western China and provide a scientific guarantee for the formulation of safety measures under such conditions.

The likelihood of pre-hypertensive young adults developing hypertension has been steadily increasing over the past few years. Despite the fact that aerobic exercise training (AET) has demonstrated positive results in lowering high blood pressure, the efficacy of different types of AET among pre-hypertensive young adults has not been well-established. The objective of this study was to evaluate the effectiveness of high-intensity interval training (HIIT) and continuous moderate-intensity training (CMT) on blood pressure (BP) of physically inactive pre-hypertensive young adults. 32 adults (age 20.0±1.1 years and BMI 21.5±1.8) were randomly assigned into 3 groups: HIIT, CMT and control (CON). HIIT and CMT groups participated in 5 weeks of AET; while the CON group followed a DASH diet plan only. The HIIT protocol consisted of 1:4 minute work to rest ratio of participants 80%-85% heart rate reserve (HR-reserve) and 40%-60% HR-reserve respectively for 20-minutes, CMT group exercised at 40%-60% of HR-reserve continuously for 20-minutes. In both HIIT and CMT groups, systolic blood pressure (SBP) (3.8±2.8 mmHg, P=0.002 VS 1.6±1.5 mmHg, P=0.011) was significantly reduced. While, significant reductions in the diastolic blood pressure (DBP) (2.9±2.2 mmHg, P=0.002) and mean arterial pressure (MAP) (3.1±1.6mmHg, P<0.0005) were noted only in the HIIT group. No significant differences in SBP (-0.4±3.7 mmHg, P=0.718), DBP (0.4±3.4 mmHg, P=0.714), or MAP (0.1±2.5mmHg, P= 0.892) were observed in the CON group. Both HIIT and CMT decreased the BP in physically inactive pre-hypertensive young adults; however, HIIT yielded more beneficial results in terms of reducing the SPB, DBP and MAP.

Prolonged high-intensity grinding can modify the crystal structure of solid substances and/or induce chemical reaction, which is referred to as mechanochemical reaction. Such reactions can exert positive influences on hydrometallurgical processes, therefore, many researchers have applied mechanochemical reactions for metals dissolution from minerals. The mechanism of mechanochemical reaction has been investigated using solid analyses and simulations. Structural changes caused by mechanochemical reaction are not yet sufficiently clarified because the ground samples are amorphous. The objective of this study was to analyze structural changes of cerianite in weathered residual rare earth ore by mechanochemical reduction. Structural change was analyzed by x-ray absorption near-edge structure and extended x-ray absorption fine structure analysis at the cerium L_III- and K-edges. These analyses revealed that the structural change of cerianite in this ore induced by mechanochemical reduction involved oxygen vacancy production. The process of the oxygen vacancy formation was closely coupled with the quantum effect of localization–delocalization of the 4f electron of cerium.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

The utilization of selective laser melting (SLM) for high entropy alloys (HEAs) holds significant promise in commercial applications, and substantial experimental research efforts have been directed toward this domain. To take advantage of the reported experimental data of SLM manufactured (SLM-ed) HEAs and reduce unnecessary experimentation, this study incorporates machine learning (ML) techniques for the phase and tensile properties prediction of SLM-ed HEAs, thus presenting a novel avenue for accelerating the discovery of new SLM-ed HEAs. Through the adjustment of material descriptors and machine learning models, a model has been developed with an impressive accuracy of 93.8% in distinguishing between face-centered cubic (FCC), body-centered cubic (BCC), and dual-phase (FCC+BCC). Additionally, optimized models have been devised for the prediction of tensile properties, namely ultimate tensile strength (UTS), yield strength (YS), and elongation (δ), achieving noteworthy MAPEs (mean absolute percentage errors) of 10.33%, 8.55%, and 28.48%, respectively. Furthermore, several HEAs were fabricated using SLM, and the experimental outcomes exhibited a favorable alignment with the predicted results. These efforts carry significant implications in advancing the utilization of SLM for HEAs.

A tunable quantum cascade laser (QCL) spectrometer was used to develop methods for detecting and quantifying high explosives (HE) in soil based on multivariate analysis (MVA) and artificial intelligence (AI). For quantification, mixes of 2,4-dinitrotoluene (2,4-DNT) with concentrations from 0% to 20% w/w were investigated using three types of soils: bentonite, synthetic soil, and natural soil. A Partial least squares regression model was generated for predicting 2,4-DNT concentrations. To increase its selectivity, the model was trained and evaluated using additional analytes as interferences, including other HEs such as PETN, RDX, and TNT and non-explosives such as benzoic acid and ibuprofen. For detection, mixes of different explosives in soils were used to implement two AI strategies. In the first strategy, the spectra of the samples were compared with those of soils recorded in a database to identify the most similar soils based on QCL spectroscopy. Next, a Classical Least Squares preprocessing (Pre-CLS) was applied to soils spectra selected from the database. The parameter obtained based on the sum of the weights of Pre-CLS was then used to generate a simple binary discrimination model for distinguishing between contaminated and uncontaminated soils, achieving an accuracy of 0.877. In the second AI strategy, the same parameter was added to a principal component matrix obtained from spectral data of samples and used to generate multi-classification models based on different machine learning algorithms. A Random Forest model worked best with 0.997 accuracy and allowing to distinguish between soils contaminated with DNT, TNT, or RDX and uncontaminated soils.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

High-frequency near-infrared diode laser provides high peak output, low heat accumulation, and efficient biostimulation. Although these characteristics are considered suitable for osteoarthritis (OA) treatment, the effect of high-frequency near-infrared diode laser in in vitro or in vivo OA models has not yet been reported. Therefore, we aimed to assess the biological effects of high-frequency near-infrared diode laser irradiation on IL-1β-induced chondrocyte inflammation in an in vitro OA model. Normal Human Articular Chondrocyte-Knee (NHAC-Kn) cells were stimulated with human recombinant IL-1β and irradiated with high-frequency near-infrared diode laser (910 nm, 4 or 8 J/cm2). The mRNA and protein expression of relevant inflammation- and cartilage destruction-related proteins was analyzed. IL-1β treatment significantly increased the mRNA levels of IL-1β, IL-6, TNF-α, MMP-1, MMP-3, and MMP-13. High-frequency near-infrared diode laser irradiation significantly reduced the IL-1β-induced expression of IL-1β, IL-6, TNF-α, MMP-1, and MMP-3. Similarly, high-frequency near-infrared diode laser irradiation decreased the IL-1β-induced increase in protein expression and secreted levels of MMP-1 and MMP-3. These results highlight the therapeutic potential of high-frequency near-infrared diode laser in OA.

A new approach to the treatment of wound lesions, which are complicated by the presence of polyresistant microflora and a possible immunodeficiency background has been proposed. It involves treating the wound surface with high-intensity pulsed optical radiation of a continuous spectrum, continuously covering the entire UV range (from 200 to 400 nm), visible and near infrared region of the spectrum. A pulsed xenon lamp is used as a radiation source. A description of the design and technical characteristics of the developed device for high-intensity optical irradiation "Zarnitsa-A", which implements the proposed medical technology for wound therapy, is represented. The results of preclinical studies of the apparatus in vitro and in vivo are represented hereinafter. The article shows that the apparatus exposure has pronounced bactericidal and wound-healing properties. The apparatus action reliably provides higher rates of wound healing compared to the use of only a typical antibacterial and wound healing agent – “Levomekol” ointment.

Large-area nanostructuring of glasses using intense laser beam remains a difficult task due to the extreme non-linear absorption of the laser energy by the material. Precise optimization of the process parameters is essential for fabricating nanostructures with large area coverage. In this study, we report the findings on creating high spatial frequency LIPSS (HSFL) on borosilicate glass through direct laser writing, using a femtosecond laser with a wavelength λ = 800 nm, pulse duration τ = 35 fs, and repetition frequency frep = 1 kHz. The orientation of the HSFL was found to be parallel to the electric field vector. We measured the single pulse ablation threshold (Fth=3.87±0.26 J/cm2) and incubation factor (S=0.68±0.03) of Borosilicate glasses for precise control for large area surface structuring. Single-spot experiments indicate that uniform LIPSS formation is limited by melt formation inside the irradiated area for higher fluence and a larger number of irradiated laser pulses. The orientation of the scan axis with the laser beam polarization is found to be significantly influencing the uniformity of the large area processing. We found that the orientation of the scan axis with the laser beam polarization significantly affects the uniformity of large-area processing, with redeposition and melt formation being higher when the scan axis is perpendicular to the laser beam polarization. Large-area processing of the borosilicate glass surface is done by line-by-line scanning over the surface with a scan orientation parallel to the laser beam polarization. The optical characterization reveals that the transmittance and reflectance of the borosilicate glass decreased significantly after processing. Also, the wettability of the surface has been changed from hydrophilic to super hydrophilic after processing. These chemical contamination-free and uniformly distributed structures have potential applications in optics, microfluidics, photovoltaics, and biomaterials.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Several studies have shown that physical activity (PA) is related to physical and mental health. Yet, there are few studies on the frequency of PA as it relates to health and a healthy lifestyle. The purpose of this study was to investigate the relationship between the frequency of practicing different types of physical activities (dependent variables), living a healthy lifestyle (BMI, smoking and alcohol consumption), physical health (sum of all doctor visits except psychiatrists) and mental health (a sum of visits to psychiatrists) at different ages (independent variables). We fo-cused on three types of PA: (1) medium to high-intensity aerobic exercises; (2) low to medium intensity relaxing and stretching exercises, (3) outdoor leisure PA. 9,617 participants (ages: 19 -81) were included in the study (with health registries over a period of 10 years prior to a cross-sectional survey). Descriptive statistics and multinomial logistic regression on frequencies of three types of PA and factors related to health and healthy lifestyles, as well as age and sex, were performed in this study. The results indicate that a higher frequency of practicing PA had a higher probability of association with the following factors: lower BMI, less or non-smoking behavior (types 1 & 3); higher education (types 1 & 2); higher age (types 2 & 3) and better physical health (type 1). Occasional (practicing sometimes) PA, type 2, was positively associated with poorer mental health (higher number of psychiatrist visits). Women were more likely to practice PA type 2, and men – PA types 3 & 1. Conclusion: In general, a higher frequency of PA is related with better health and healthy life styles; with the exception of PA type 2 that is related to poorer mental health.

BKW is a highly efficient Storage Function-type rainfall-runoff model that utilizes the steady-state storage (S) and outflow (Q) of a catchment at different rainfall intensities as the S-Q relation of the catchment. For the inundation nowcasting of urban areas under high-intensity, short-duration rainfall, a Storage Function-type model is a judicious choice. However, S-Q hysteresis exists in the catchment S-Q relation, and BKW is unable to exhibit hysteresis due to assuming that the S-Q relation of a catchment is a nonlinear relation. The S-Q hysteresis can influence the outflow estimation of BKW, reducing the model's accuracy. Through the evaluation of analytical solutions, we found that the change in rainfall intensity dominates the S-Q relation of a catchment. The S-Q relation during a rainfall event is a dynamic process rather than a monotonic nonlinear relation. By applying the dynamic S-Q relation in BKW, we improved BKW to become a highly efficient and accurate rainfall-runoff model for small urban catchments.

This article presents results of the polarization laser studies of the optical and microphysical characteristics of the high-level clouds (HLC). The high-altitude matrix polarization lidar (HAMPL; Tomsk, Russia) is described. HAMPL measures vertical profiles of all elements of the backscattering phase matrix (BSPM) of the HLC. Based on the joint analysis of lidar and radiosonde observations it is shown that the spatial structure of the HLC containing oriented ice crystals is inhomogeneous in the horizontal wind direction. It includes local areas with oriented particles; the sizes of such areas are estimated together with the most probable meteorological conditions of their formation. The shortcomings of the radiosonde observations performed closest to the location of the HAMPL are described. The applicability of the ERA5 reanalysis data of the European Centre for Medium-Range Weather Forecasts for use as an alternative source of information on the vertical profiles of meteorological quantities for the interpretation of HLC lidar sensing data in Western Siberia was checked.

Hong Kong was under the direct hit of Severe Typhoon Koinu (2314) on 8 and 9 October 2023, necessitating the issuance of the Increasing Gale or Storm Signal, No. 9. Koinu was a very challenging case for TC forecasting and warning services due to its compact size and erratic movement over the northern part of the South China Sea. This paper reviews the difficulties and challenges on the forecasting aspect of the severe typhoon. The predicted tropical cyclone track and intensity from both conventional models and emerging artificial intelligence models are examined, as well as local wind and rainfall forecast. Experience in this case study showed that while deterministic global models only performed moderately and were not able to adequately support early warning, a regional model and AI models could more effectively support decision making for operational tropical cyclone warning service.

Hong Kong was under strike from Super Typhoon Saola (2309), necessitating the issuance of the highest tropical cyclone warning signal. Saola skirted past the south-southwest of Hong Kong, bringing hurricane force winds and significant storm surge. Saola had its closest approach to Hong Kong on 1 September 2023, posing a unique challenge in forecasting and early warning for the commencement date of the new school term, where higher impact to traffic and public safety was anticipated. This paper covers the challenges on the forecasting aspect of the super typhoon. The predicted tropical cyclone track, intensity and wind structure are reviewed. Experience in this case showed that while there was not a perfect numerical weather prediction model in terms of the forecast track, intensity and wind structure of Saola, multi-model approach provided very use-ful and crucial information for operational weather warning services.

Mango flowering phenostages were recorded under global warming conditions to assess the relationship between environmental cues and flowering time shifts and their consequences on reproductive success. Phenological transition to floral destiny was studied in relation to standard metrological week and weather parameters. Shifting of phenostage was recorded in Bud swelling, which is important for the shoot transitioning from vegetative to flowering meristem. Variations were also recorded for panicle elongation and early anthesis. The critical temperature for Bud burst stage was estimated for Dashehari, Langra, Amrapali and Chausa while Chausa had the propensity for late flowering correlated with higher temperature. The shifting of phenological calendar in response to weather parameters was obvious and needed a bigger range of yearly data for arriving at the climatic drives. In general, the results revealed that flower intensity was positively correlated with temperature, sunshine hours and evaporation while humidity showed a negative correlation. Hermaphrodite Flower % is an important attribute affecting fruit set and yield and was found most variable in the two years in the case of the three alternate bearing cultivars. In conclusion, it can be inferred that weather parameters prevailing in subtropics affect flowering intensity and consequently its fate i.e.; fruit yield.

In this study, UAV (Unmanned Aerial Vehicle) photogrammetry was used to monitor the ground displacement on the slope below a coal waste-rock stockyard, and to investigate the role of rainfall on this displacement. The study area is a mountainous region in Korea, where coal mining continues, and coal waste-rock is stored on the slopes of the mountain. In this area, ma-terial removal work was undertaken to reduce the steepness of the slope and driving forces in order to prevent disasters, but the strategy requires continuous monitoring to confirm the stabilization of the slope. For slope monitoring, a total of six UAV photogrammetry campaigns were conducted between April 2019 and August 2020. As a result of data processing, an orthoimage and DSM (Digital Surface Model) were generated. The ground displacement was estimated through four ways: slope extraction, displacement area evaluation, horizontal displacement, and vertical displacement analysis. During the study period, the maximum vertical displacement was 3.3 m and the maxi-mum horizontal displacement was 3.5 m. The horizontal displacement was effectively evaluated through the measurement of the movement of the drainage system using orthoimages that captured with a periodic survey. The effects of rainfall on ground displacement were also investigated. A very clear linear relationship between rainfall intensity higher than 20mm/d and ground displacement was identified. Accumulated amount of rainfall also showed good correlation with slope movement, but the frequency of rainfall intensity below 20 mm/d showed relatively low correlation with ground dis-placements.

An effective process monitoring strategy is a requirement for meeting the challenges posed by increasingly complex products and manufacturing processes. To address these needs, this study investigates a comprehensive scheme based on classical machine learning methods, deep learning algorithms, and feature extraction and selection techniques. In a first step, a novel deep learning architecture based on convolutional neural networks (CNN) and gated recurrent units (GRU) is introduced to predict the local weld quality based on mid-wave infrared (MWIR) and near-infrared (NIR) image data. The developed technology is used to discover critical welding defects including lack of fusion (false friends), sagging and lack of penetration, and geometric deviations of the weld seam. Additional work is conducted to investigate the significance of various geometrical, statistical, and spatio-temporal features extracted from the keyhole and weld pool regions. Furthermore, the performance of the proposed deep learning architecture is compared to that of classical supervised machine learning algorithms, such as multi-layer perceptron (MLP), logistic regression (LogReg), support vector machines (SVM), decision trees (DT), random forest (RF) and k-Nearest Neighbors (kNN). Optimal hyperparameters for each algorithm are determined by an extensive grid search. Ultimately, the three best classification models are combined into an ensemble classifier that yields the highest detection rates and achieves the most robust estimation of welding defects among all classifiers studied, which is validated on previously unknown welding trials.

Background: According to EWGSOP2, the diagnosis of sarcopenia is confirmed when in addition to low muscle strength, low muscle quantity or quality is present. Echo intensity (EI) determined by muscle ultrasound (US) has been proposed as an efficient method for the assessment of muscle quality. The effect of changing various US parameter settings on EI remains unclear. Therefore, the aim of this study was to assess the differences between EI values obtained by adjusting parameter settings over their entire range in a sample of middle-aged healthy subjects. Methods: Thirty-two repeated US scans of rectus femoris (RF) and rectus abdominis (RA) muscles were taken in eight men and three women with a portable Mindray M7 premium US machine, working in an Extended field-of-view, B-Mode setup, equipped with a linear 5.0-10.0 MHz transducer. The following US parameters and settings were fixed: gain 60dB, depth 6.5cm, and frequency 10 MHz. Readily adjustable parameters were dynamic range (DR), gray map (GM), line density, persistence, and IClear. A default setting DR65 was chosen as the reference setting. For each of the parameters, the settings of one single parameter of interest was changed over its entire range following a standardized protocol. The EI values were calculated using the open-source software ImageJ. Repeated measures analyses were performed to evaluate the effect of parameter settings on EI. Linear interpolation was used to determine non-significant ranges across a given parameter. Results: For the RF muscle, the EI values were significantly different across DR (p<0.001), GM (p<0.001), and IClear (p<0.001). Post hoc analysis confirmed the differences within these three settings. Echo intensity values within the range of DR55 to DR80 were not significantly different. For the RA muscle, the EI values were significantly different across DR (p=0.004) and GM (p=0.030). Post hoc pairwise comparisons revealed no significant difference with the default setting, except for DR150 (p=0.042). Conclusion: We showed that EI values differ across the DR and GM range, especially in the RF. We suggest using a DR setting within its midrange to minimize the effect of machine setting-dependent factors on EI values. These findings reconfirm the need for standardization of ultrasound echo intensity settings when applied for diagnostic purposes of muscle quality.

Quantity-intensity characteristics are among conventional approaches for studying potassium dynamics and its availability; this was assessed to determine availability in four districts: namely, Sodo Zuria, Damot Gale, Damot Sore, and Boloso Sore at three different land use type viz., enset-coffee, crop land, and grazing land. There was water soluble, ammonium acetate, nitric acid extractable potassium, exchangeable potassium, and non-exchangeable potassium studied in soil samples, which were collected from 0-20 cm depth of each land type. The study revealed that water soluble and ammonium acetate extractable potassium concentrations ranged from 0.04 to 0.42 cmolKg-1 soils enset-coffee and grazing land use types, respectively. The study showed that exchangeable potassium constituted the highest proportion of available potassium, while the proportion of water soluble potassium was found to be the lowest. In this study, non-exchangeable potassium concentrations varied from 0.10 to 0.04cmolKg-1soils for enset-coffee, and crop and grazing land use type. Furthermore, available potassium and exchangeable potassium concentrations were positively correlated with OC(r=0.95***), cation exchange capacity, and sand and clay(r=0.98***). In addition, the K dynamics as impacted by land use types found that the highest change in exchangeable potassium (0.31cmolkg-1soils) and potential buffering capacity (1.79cmolkg-1soils) were noted in crop land use types, whereas the lowest change(1.26cmolkg-1 soils) was observed in the enset-coffee system, The varying properties, potassium status, dynamic and land use type of soils identified in the study areas provided adequate information to design soil potassium management options and further research about the soil in each site. Therefore, application of site specific soil fertility management practices and research can improve soil potassium status and quantity intensity parameters to sustain crop productive soils.

Indian pangolins are insectivorous mammals with less-known ecology. Due to the lack of sufficient literature on their dietary ecology, captive raring of this species has become problematic. This article describes data on dietary composition and foraging habitats of the Indian Pangolin (Manis crassicaudata) in a tropical lowland forest-associated landscape in Southwest Sri Lanka. Five different types of habitats were investigated in this study: Forest, rubber plantation, cinnamon cultivation, oil palm plantation, and tea-dominated home gardens. Foraging preference of the Indian pangolin for each habitat was assessed using signs of foraging activities. To further observe the foraging habitat utilization of pangolins, photographic evidences were collected using Infrared (IR) active camera traps located in all the studied habitats. Faecal samples collected from same habitats were further examined to identify the dietary composition of Indian Pangolins. As termites and ants are major prey organisms of Indian pangolins, the digestibility of different body parts –heads, mouthparts, abdomens, and legs of termites and ants was also scrutinized. The findings of the study with regard to dietary ecology will be important for both captive feed preparation and future conservation planning of the species

The water and wastewater sectors are energy-intensive, and so a growing number of utility companies are seeking to identify opportunities to reduce energy use. Though England’s water sector is of international interest, in particular due to the early experience with privatisation, for the time being very little published data on energy usage exists. We analyse telemetry data from Thames Water Utilities Ltd. (TWUL), which is the largest water and wastewater company in the UK and serves one of the largest mega-cities in the world, London. In our analysis, we (1) break down sectoral energy use into their components, (2) present a statistical method to analyse the long-term trends in use, as well as the seasonality and irregular effects in the data, (3) derive energy-intensity (kWh m³) figures for the system, and (4) compare the energy-intensity of the network against other regions in the world. Our results show that electricity use grew during the period 2009 to 2014 due to capacity expansions to deal with growing water demand and storm water flooding. The energy-intensity of the system is within the range of reported figures for systems in other OECD countries. Plans to improve the efficiency of the system could yield benefits in lower the energy-intensity, but the overall energy saving would be temporary as external pressures from population and climate change are driving up water and energy use.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

In this paper, we examine a modified Friedmann model designed to explain cosmic structures and late-time accelerated expansion of the universe, grounded in the spatial distribution of luminous matter. Through comprehensive simulations of our universe, we observe a notable surge in the formation rate of galaxies at redshift z≈1, characterized by a peak expansion rate in cosmic structures formed at z ≈0.9, reaching its zenith at z ≈2. Subsequently, a transition occurs before the onset of dark matter-induced accelerated expansion. The acceleration of the universe stands as an entrenched and virtually model-independent theoretical tenet, resilient to the ongoing debate surrounding the enigma of dark energy. A distinctive redshift transition zone marks the shift from cosmic deceleration to accelerated expansion. The transition is proportional to matter density and contingent upon the geometry of the universe. The influence of the cosmological constant on the evolution of cosmic structures in the CDM paradigm appears insufficient in curtailing the efficiency of late-time structure formation compared to the observed values in the modified model

Road marking recognition is of great importance for the deployment of automated driving systems and for already existing driver line-keeping assistance systems. For proper and reliable function of machine vision systems that include LiDAR and camera, road markings must be visible to them to facilitate planning of driving trajectory. In this study, LiDAR intensity and the number of LiDAR points collected from a field analysis of two road markings systems reflectorised with premium and standard glass beads were analysed. In the lateral direction, it was demonstrated that the use of premium glass beads for road markings lead to 56% higher LiDAR intensity and 14% more LiDAR points captured than in case of standard road markings. In the longitudinal direction, premium road markings showed less distance attenuation, which is seen as advantageous for trajectory planning by machine version systems. The outcomes of this study offer insights for road infrastructure decision-makers, developers of automated driving systems, and researchers in the field of transportation technology.

There are four commercial pathways to make grill charcoal from wood. These have been modelled to calculate a carbon intensity (CI) for each. Results are presented along with discussion of the sensitivities: biogenic carbon; quality of the charcoal; classification of products, wastes and residues; and division of burden. Grill charcoal’s CI ranges greatly, depending on the pathway by which it is produced. Wood distillation, a commercial process that once was common but now is rare, has a CI 50+% lower than that of the next-lowest commercial process, Kilns. Earth mounds/pits and external-fuelled Retorts have CIs considerably higher still. The carbon efficiency (CE) of Wood distillation is more than twice that of the next-best, again Kilns. CE is defined as normalised, total carbon emitted. This is not the same as CI, it is not usually considered in studies such as this, yet it is important for climate impact. CE could be a useful measure in assessments (such as this) where biogenic carbon is significant.

Objective: To investigate the feasibility and preliminary effects of a 12-week home-based moderate intensity cycling programme in stroke survivors. Design: Single-blinded, parallel group, Randomised Controlled Trial Setting: Home-based Participants: Participants will be survivors of first-ever stroke and randomly assigned to an Active Cycling Group (ACG) or control group. Intervention: The ACG performed a 12-week home-based cycling programme, three sessions per week. Work intervals were executed at 75% of the maximal heart rate (HR_max), recovery intervals at 50% of HR_max. Work interval duration increased from three ten-minute intervals to 30 minutes continuous cycling. The control group completed a 12-week neurocognitive exercise programme. Main outcome measurements: Primary outcome measures are compliance with training, adherence to protocol and safety as measured by adverse events. Secondary outcome measurements included a: simplified modified Rankin Scale questionnaire (stroke severity), Six-Minute Walking Test (walking ability), Ten-meter Walk Test (walking ability), Rivermead Mobility Index (walking ability), graded submaximal cycling test (exercise capacity), Physical Activity for Individuals with Physical Disability questionnaire (physical activity), EQ-5D-5L (quality of life), Stroke Specific Quality of Life questionnaire (quality of life), Montreal Cognitive Assessment (cognition), General Self-Efficacy Scale (self-efficacy), and Exercise Self-Regulation Questionnaire (self-regulation).

Trade of agricultural products has gained importance with the development of global trade. Cherries has a crucial place in Turkish agricultural exports. Fresh cherries are in the scope of this study. The aim of this study is to examine Turkey’s position and competitiveness in cherry trade. Trade Intensity Analysis Method which represents the course of trade flow among countries is used in the study. The study indicates that European countries which are Turkey’s tradition trade partner has a biggest trade share with Turkey and that share did not much change in years. By the way, Asia market especially China, became a game changer in cherry trade and Turkey should prepare itself for this situation.

The International System of Units (SI) was adopted in 1960 as a universal measuring system to be used for all areas of science. Sports Science papers have shown lots of inaccurate and inappropriate terms for quantification of athletes’ performance and the psychobiological responses to exercise (e.g., internal load). In biomechanics, external and internal loads are forces acting externally and internally, inducing stress and strain in the biological tissues. Therefore, the current review present simple proposals to correct the inappropriate terms: 1) do not use the term external load when referring to the assessment of exercise time, distance, displacement, speed, velocity, acceleration, torque, work, power, impulse, etc.; 2) do not use the term internal load when referring to the assessment of psychobiological stress markers (i.e., session rating of perceived exertion, heart rate, blood lactate, oxygen consumption, etc.); 3) do not use the term impulse when expressing other calculus than integrating force with respect to time, and neither strain, when expressing other phenomena than the body deformation. Instead, the term exercise intensity is universal and can be used to describe all forms of exercise. Finally, duration should precisely be described according to physical quantities (e.g., time, distance, displacement, speed, velocity, acceleration, force, torque, work, power, impulse, etc.) and the units accomplish by use of the SI. These simple quantifications can be performed for the exercises, sessions, microcycles, mesocycles and macrocycles of the athletes. Such standardization will provide a consistent and clear communication among sports scientists and all areas of science.

Product innovation is a crucial factor in enterprise survival. Even though there are sources from strategic theory that guides the clear comprehension towards appreciating the nexus between these two variables (product innovation and enterprise survival), there are still many lacunas that should be addressed and filled. Consequently, the need for additional empirical corroboration or support is pertinent. This study aimed at verifying the nexus between product innovation and enterprise survival, and how they are affected by the existence of antecedent variables such as competitive intensity and competitive advantage. In the methodology, this study adopts the conduct of explanatory and cross-sectional investigations through the use of structural equation modelling (SEM) to a sample of selected food and beverages enterprises in Lagos, Nigeria. Regarding the food and beverage enterprises in Lagos, Nigeria, this study discovered that competitive intensity has huge positive implication on product innovation at (0.39; t = 5.69, p < 0.05). This gives numerical evidence that, in the face of more market competition, enterprises will be pressured to adopt the model of costs reduction on products which will enhance the reduction of product prices, and will have significant impact on profit. However, the findings reveal that there is no significance between competitive advantage and product innovation at (0.002; t = 0.203, p > 0.05), and there is no significance between product innovation and enterprise survival at (-0.035; t = -1.583, p > .05). As a result, the food and beverage enterprises should concentrate more on product innovation so that they will be able to stand the intensity of competition. The results emanated from the study is germane as it make significant contribution to literature and the body of knowledge and on strategic management by enlightening that competitive intensity is a necessary inducement for product innovation.

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

Aiming at the defects of low precision and time cumulative error, an external wireless signal weighted centroid localization algorithm aided inertial positioning method is designed in this paper. According to the signal strength of each anchor node received at the test point, the distance between the anchor node and the anchor node is obtained by using the attenuation model of the wireless signal. Three anchor nodes are used to measure the distance between the anchor node and the measured point. We can obtain the area to be measured according to the actual situation, the position of the measured point is obtained by the weighted centroid localization algorithm and a combined model of wireless signal aided inertial navigation system is established. The simulation results show that the method can greatly improve the positioning accuracy and restrain the divergence of the longitude error and latitude error.

Understanding the evolution patterns in patients diagnosed with acute myeloid leukemia (AML) after therapy is relevant due to the dismal outcome still present in refractory or relapsed AML patients. We performed a retrospective, single-center study to evaluate the mutation profile in paired samples obtained at the time of diagnosis and at the onset of progressive or refractory disease in patients diagnosed with AML through a commercial next-generation sequencing (NGS) panel. In total, 62 patients were analyzed. Of these, 28 patients received ICT, and 34 patients underwent low-intensity treatments. In LIT patients, there were emergent mutations at progressive disease in a 64% (22/34) of the patients. Emergent mutations in the RAS-MAPK signaling pathway were observed in 35.9% (12/34) , corresponding to 54.5% of all patients with emergent mutations (12/22). These were found in 12/22 patients that received venetoclax in combination with hypomethylating agents. Six presented mutations in genes related to the RAS-MAPK pathway. Emerging mutations are frequently observed at progressive AML disease after therapy. In patients treated with LIT, mutations in RAS-MAPK signaling pathway might have a key role on the secondary clinical resistance, not only if they are present at diagnosis, becoming a potential target for the development of new drugs.

As one of the main projects of facility agriculture promotion, the photovoltaic greenhouse has the problems of photovoltaic power generation competing for light with crop production, strong indoor chiaroscuro, and uneven light distribution. The internal light uniformity is tested by a zigzag greenhouse model to compare the light transmission effects of different light-transmitting materials applied to photovoltaic greenhouses. 20 line\inch 3mm and 30 line\inch 3mm, 40 line\inch 2mm, 25 line\inch 4mm grating plates, 2mm, and 3mm thick ordinary glass were used as light transmitting components, and the light intensity and light uniformity in the greenhouse were the measurement indicators. The results show that the use of grating plates as covering material can improve the light intensity at the intersection of light and dark, but the overall light transmittance is not as good as glass, because it is plastic which is easy to age with low light transmittance. It can also improve the use of land under the shade of photovoltaic modules to provide a better growth environment for crops. Test results show that the use of a 2mm thick 40-line grating plate can maximize the light intensity of the greenhouse, and the peak value can reach 69336 Lx. In sunny weather, the light intensity from point G to point I in the greenhouse is greater than 20,000 Lx, and the light environment in other areas is between 5,000 Lx and 20,000 Lx, which is suitable for planting shade-loving crops.

Cognitive linguistics is founded on the assumption that language is a reflection of universal cognitive principles, implying that all cognitive processes share a common origin. This assumption is known as the 'Cognitive Commitment.' The present article examines the sensory schema hypothesis, which traces all forms of expression back to sensations. This theoretical framework integrates the physicality of the body with sensations that underlie human experiences and their linguistic and non-linguistic expressions. By challenging the traditional dichotomy between mind and body, it provides a more integrated understanding.

The adoption of sustainable forest management practices emerged as a contemporary imperative for forest biodiversity preservation, functional integrity, and mitigation of climate change. Within the spectrum of these practices, thinning is recognized as an environmentally sustainable strategy. The primary objective of thinning is the equitable redistribution of aboveground growth, diverting resources from younger trees to promote the accelerated development of more valuable specimens compared to unthinned forests. Thinning, while fostering aboveground changes, induces substantial alterations in soil chemical and biochemical properties. This review addresses the often-debated consequences of thinning on soil characteristics, focusing on the intricate interplay involving different thinning intensities and their impact on soil chemical and biochemical parameters. Specifically, the analysis delves into the modulation of organic carbon levels, microbial biomass, and enzymes crucial to the organic matter cycle. Two key aspects are scrutinized: firstly, the influence of thinning intensity and the temporal dimension post-thinning on soil properties; secondly, the comparative impact of thinning intensity versus the time elapsed from the thinning event on soil properties and associated biological processes. The findings underscore pivotal insights: a) temporal dynamics significantly affect soil organic matter across broadleaved (excluding beech), coniferous, and mixed forests, manifesting as early as 2-7 years post-thinning; b) thinning intensity, up to a threshold of 50%, enhances soil quality by augmenting organic carbon content, bolstering microbial communities, and amplifying associated enzyme activities. This review consolidates valuable information for forest managers, providing guidance to optimize natural processes in tandem with achieving specific management objectives. By illuminating the nuanced interactions between thinning practices and soil dynamics, this knowledge equips stakeholders to make informed decisions in the pursuit of sustainable forest management and ecological resilience.

Recently, new semantic segmentation and object detection methods have been proposed for direct processing of three-dimensional (3D) LiDAR sensor point clouds. LiDAR can produce highly accurate and detailed 3D maps of natural and man-made environments and is used for sensing in many contexts due to its ability to capture more information and its robustness to dynamic changes in the environment. In addition, the cost of LiDAR sensors has decreased in recent years, which is an important factor for many application scenarios. The challenge with 3D LiDAR sensors like the Velodyne HDL-64E S2 is that they can output large 3D data at up to 1,300,000 points per second, which is difficult to process in real time when applying complex algorithms and models for efficient semantic segmentation. Most existing approaches are either only suitable for relatively small point clouds or rely on computationally intensive sampling techniques to reduce their size. As a result, most of these methods do not work in real-time in realistic field robotics application scenarios, making them unsuitable for practical applications. Systematic point selection is a possible solution to reduce the amount of data to be processed, but although it is memory and computationally efficient, it selects only a small subset of points, which may result in important features being missed. To address this problem, we propose a new approach to semantic segmentation in forestry that uses a systematic sampling method in which the local neighbors of each point are retained to preserve geometric details. Our approach has been shown to process up to 1 million points in a single pass. It outperforms the state of the art in efficient semantic segmentation in large datasets such as Semantic3D. We also present a preliminary study on the performance of LiDAR-only data, i.e., intensity values from LiDAR sensors without RGB values for semi-autonomous robot perception.

The Rb/Sr ratio of lake sediments has been widely adopted as an indicator of weathering intensity in studies of past climate change, but the geochemical significance of this ratio varies with timescale. Here we present Rb/Sr data for the last 300 years for sediments collected from Chaonaqiu Lake in the Liupan Mountains of the western Chinese Loess Plateau as a decadal-scale record of weathering intensity. To validate the application of this weathering proxy, we correlated the record with those of other major elements, rock-forming minerals, and paleoclimatic proxies. We found that Rb/Sr ratios are influenced mainly by Sr activity within the lake catchment (where Sr is likely sourced from albite). In addition, higher (lower) Rb/Sr ratios of bulk sediments from Chaonaqiu Lake are correlated with lower (higher) fractions of terrigenous detritus (SiO2, Ti, K2O, Al2O3, and Na2O). Lake bulk sediment Rb/Sr ratios are dominated by the input of terrigenous detritus over decadal timescales. Our data show that physical and chemical weathering in Chaonaqiu Lake catchment have opposing influences on bulk sediment Rb/Sr ratios, competing to dominate these ratios of lake sediments over different timescales, with ratios reflecting the relative importance of the two types of weathering. We infer that the Rb/Sr ratios of Chaonaqiu Lake sediments reflect climatic signals of precipitation and temperature over long timescales and of precipitation over short timescales.

Purpose: This study aimed to examine how aging and modifications of critical acoustic parameters may affect the perception of whispered speech as a degraded signal. Method: Forty Mandarin-speaking adults were included in the study. Part 1 of the study compared the perception of Mandarin lexical tones, vowels, and syllables in older and younger adults in whispered vs. phonated speech conditions. Parts 2 and 3 further examined how modification of duration and intensity cues contributed to the perceptual outcomes. Results: Perception of whispered tones was compromised in older and younger adults. Older adults identified lexical tones less accurately than their younger counterparts, particularly for phonated T2, T3 and whispered T3. Aging also negatively affected the vowel identification of /i, u/ in the whispered condition. Syllable-level accuracy was largely dependent on the accuracy of lexical tones and vowels. Furthermore, reduced duration led to the decreased accuracy of phonated T3 and whispered T2, T3 but increased accuracy of phonated T4. Reduced intensity lowered the recognition accuracy for phonated vowels /i, ɤ, o, y/ in older adults and /i, u/ in younger adults, and it also lowered the accuracy of whispered vowels /a, ɤ/ in older adults. Contrary to our expectation, increased duration and intensity did not improve older adults’ speech perception in either phonated or whispered conditions. Conclusion: The results suggest that aging adversely affected speech perception in both phonated and whispered conditions with more challenges in identifying whispered speech for older adults. While older adults’ diminished performance may be potentially due to problems with processing the degraded temporal and spectral information of the target speech sounds, it cannot be simply compensated for by increasing the duration and intensity of the target sounds beyond the audible level.

Compared with liquid crystal clad waveguide, MEMS mirror has some merits, such as high-er-transmissivity, lager-angle of scanning, faster scanning speed and so on. Furthermore, MEMS mirror arrays perform more superior than MEMS mirror when they steer laser beam, which make MEMS arrays much more suitable to be used in devising compact Lidar. Before assembling a Lidar with MEMS arrays, the optical intensity and distributions of the laser diffracted by MEMS arrays should be analyzed, but few published papers about this issue are available so far, this paper will focus on this issue about MEMS arrays. Firstly, the complex amplitudes of laser which is diffracted by 1-D and 2-D arrays are presented, respectively. Then the optical intensity and distributions on the observation plane are presented. Finally, the simulation diagrams of these distributions are shown, and the correctness of the results is indirectly verified by Young’s dou-ble-slit experiment. The results gotten in this letter are essential to design a compacted Lidar based on MEMS arrays.

Focal vibration therapy can provide neurophysiological benefits. Unfortunately, standardized protocols are non-existent. Previous research presents a wide range of protocols with a wide range of effectiveness. This paper is part of a broader effort to identify effective, standardized protocols for focal vibration therapy. The vibration characteristics of four commercially available focal vibration devices that have been used for research and clinically were measured. An accelerometer was used for the measurements. Frequency and peak-to-peak amplitude were measured. Measurements were made when the devices were free and then again when they were strapped to the human body. Vibration frequency ranged from 120 to 225 Hz. Free vibration amplitude ranged from 2.0 to 7.9 g’s (peak-to-peak). When the devices were strapped to the body (constrained), vibration amplitude decreased by up to 65.7%. These results identify effective ranges of focal vibration frequency and amplitude. They illustrate the importance of identifying vibration environment, free or constrained, when quoting vibration characteristics. Finally, the inconsistency of multi-actuator devices is discussed. These results will guide protocol development for focal vibration and potentially better focal vibration devices.

In the context of improving the comfort and dynamics of the vehicle, the suspension system has been continuously developed and improved, especially using magnetorheological (MR) shock absorbers. The development of this technology which is relatively new has not been easy. Thus, the first widespread commercial use of MR fluid in a semi-active suspension system was implemented in passenger cars. The magnetorheological shock absorber can combine the comfort with the dynamic driving, because it allows the damping characteristic to be adapted to the road profile. The main objective of the paper is to analyze the dynamic behavior of the magnetorheological shock absorber in the semi-active suspension. In this sense, the author carried out a set of experimental measurements with a damping test bench, specially built and equipped with modern equipment. The results obtained from the experimental determinations show a significantly improved comfort when using a magnetorheological shock absorber, compared to a classic one, by the fact that the magnetorheological shock absorber allows to modify the damping coefficient according to the road conditions, thus maintaining the permanent contact between the tire and the road due to increased damping force.

China’s transportation industry has made rapid progress, which has led to a mass of carbon emissions. However, it is still unclear how the carbon emission from transport sector is punctuated by shifts in underlying drivers. This paper aims to examine the process of China’s carbon emissions from transport sector as well as its major driving forces during the period of 2000 to 2015 at the provincial level. We firstly estimate the carbon emissions from transport sector at the provincial level based on the fuel and electricity consumption using a top-down method. We find that the carbon emission per capita is steadily increasing across the nation, especially in the provinces of Chongqing and Inner Mongolia. However, the carbon emission intensity is decreasing in most provinces of China, except in Yunnan, Qinghai, Chongqing, Zhejiang, Heilongjiang, Jilin, Inner Mongolia, Henan and Anhui. We then quantify the effect of socio-economic factors and their regional variations on the carbon emissions using panel data model. The results show that the development of secondary industry is the most significant variable in both the entire nation level and the regional level, while the effects of the other variables vary across regions. Among these factors, population density is the main motivator of the increasing carbon emissions per capita from transport sector for both the whole nation and the western region, whereas the consumption level per capita of residents and the development of tertiary industry are the primary drivers of per capita carbon emissions for the eastern and central region.

The aim of this study is to explore the extent of English language teaching in Higher Institutions of Malaysia and investigate the current changes, trends and challenges in this niche. A sample of 100 English learners from public and private institutions participated in this study. Analysis of the responses indicated that English language is remaining to be difficult to master, due to speaking environment, proficiency of the teachers and other factors. However, the Government is on the right direction to improve this situation by following Common European Framework of Reference of Languages. As any other system, it takes time to put into realization and start up the mechanism. This observation carries a pedagogical perspective and includes the overview of the general picture based on Private, Public and Stand Alone English educational institutions. This study has highlighted the practical importance of British Framework of English learning and suggests to focus on emphasis of the learning process instead of a result.

The EU has planned the phase-out of new vehicles based on internal combustion engines in favour of high efficiency electric cars by 2035 (Fit for 55 package). However, many doubts remain about the effectiveness of this choice for each Country of the Union in terms of CO2 emissions reduction, as each State is characterized by a different carbon intensity related to the production of electricity needed to manufacture and recharge vehicles. This study seeks to explore the Italian case. To this aim, carbon intensities related to the electricity production were calculated considering both the Italian electricity mix production at 2021 and those at 2035, envisaged considering two scenarios based on different introductions of renewable sources (RES). Afterwards, the values obtained were adopted for determining the CO2 emissions related to the whole production process of battery systems in Italy (emissions from mining and refining, scrap materials and final assembly included) by comparing some of the most up-to-date Life-Cycle Assessment (LCA) analysis related to the manufacturing cycle of the batteries. Finally, the results were adopted to calculate the starting carbon debit for A, B, C and M car segments for Mild Hybrid, Full Hybrid and Full Electric powertrains. At the same time, statistical road fuel/electricity consumption data were collected and overall CO2 emissions were calculated for the same vehicles for a defined mileage, so to determine break-even points with respect to the cumulative (i.e., from battery and road) carbon emissions. The results showed that advantages related to electric vehicles are significant only if a low carbon intensity related to electricity production is reached by means of a very high introduction of RES, thus keeping the door open for innovative powertrain technologies (plug-in), if fed with low carbon fuels.

A number of accidents at sea are primarily caused by low visibility due to sea fog therefore, it is important to estimate sea fog intensity and visibility in real-time in the ocean environment. However, the existing estimation systems have significant costs so that it is not viable to install them at various locations, such as small vessels, minor ports, and a number of buoys. Therefore, this paper proposes an algorithm called RDCP (Reduced Dark Channel Prior) which provides the estimation at a low complexity and a low cost. For the estimation, the RDCP algorithm firstly acquires dark channels from an ocean image, then applies an optimized threshold value to the dark channels, and crops out the sky region in the ocean image. For the estimation performance evaluation, 320 raw images captured from cameras at four different ports in South Korea are used rather than artificially composed images. Considering facilities in oceans which are usually operated in the power limited environment, the processing time performance of PDCP are also examined. The experiments demonstrate that the RDCP algorithm provides reliable estimation performance in real-time.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

The purpose of this study was to quantify characteristics of bimanual movement intensity during 30-hour Hand Arm Bimanual Intensive Therapy (HABIT) and bimanual performance (activities and participation) in real-world using accelerometers in children with unilateral cerebral palsy (UCP). Twenty-five children with UCP participated in a 30-hour HABIT program. Data was collected from bilateral wrist-worn accelerometers during 30-hours HABIT to quantify the movement intensity, and three days pre- and post-HABIT to assess real-world performance gains. Movement intensity and performance gains were measured using six standard accelerometer-derived variables. Bimanual capacity (body function and activities) was assessed using standardized hand function tests. We found that accelerometer variables increased significantly during HABIT, indicating increased bimanual symmetry and intensity. Post-HABIT, children demonstrated significant improvements in all accelerometer metrics, reflecting real-world performance gains. Children also achieved significant and clinically relevant changes in the hand capacity following HABIT. Therefore, our findings suggest that accelerometers can objectively quantify bimanual movement intensity during HABIT. Moreover, HABIT enhances hand function as well as activities and participation in real-world situation in children with UCP.

Dolomite is a common type of natural soluble rock. The strength of rock decreases under the action of corrosion, which has a significant impact on the self-stability and long-term safety of the tunnel surrounding the rock. To reveal the microscopic structure evolution and strength-damage law of carbonate rock caused by corrosion, chemical corrosion, rock uniaxial compression, and electron microscope scanning tests are conducted at different pH values on the dolomite of the Doushantuo Formation. The rock dissolution at different pH values exhibits four typical stages: the initial dissolution stage, secondary dissolution acceleration stage, stable dissolution rate stage, and dissolution attenuation stage. During the dissolution process, the initial dissolution rate is 25.91 times that of the stable stage, and the maximum strength attenuation is 76.2% after 21 days of dissolution. For macroscopic failure, the rock is developed from 1 to 2 external fractures to multiple internal and external fractures and penetrated, and the specimen transforms from brittle to flexible. For microstructure, the sample exhibits corrosion characteristics along the joint surface, intensified corrosion at the edge, etc. The porosity increase rate is 0.6%/d; however, the length–width ratio of the pores is maintained at 1.7–1.85, indicating that the development rate of pores in different directions is similar. The results of this study have enriched the study of the dolomite dissolution mechanism and have important reference value for the stability evaluation of tunnel surrounding rock in karst environments.

Diverse factors may have an impact in Carbon dioxide (CO₂) emissions; thus, three main contributors, energy consumption, exergy indicator and gross domestic product (GDP) are examined in this work. This study explores the relationship between economic growth and energy consumption by means of the hypothesis postulated for the Environmental Kuznets Curve (EKC). Panel data for 10 countries, from 1971 to 2014 have been studied. Despite all this wide gamma of research, the role of an exergy variable has not been tested to find the EKC; then exergy analysis is proposed. Exergy analyses were developed to propose an exergetic indicator as a control variable and a comparative empirical study is developed to study a multivariable framework with the aim to detect correlations between them. High correlation between CO₂, GDP, energy consumption, energy intensity and trade openness are observed, conversely not statistically significant values for trade openness and energy intensity. The results do not support the EKC hypothesis, however exergy intensity opens the door for future research once it proves to be a useful control variable. Exergy provides opportunities to analyze and implement energy and environmental policies in these countries, with the possibility to link exergy efficiencies and the use of renewables.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

In the present work, a study has been carried out on the contamination of heavy metals in urban dust deposited on the roads of the city of Cartagena (Spain), in order to know the content of metals such as Ni, Zn, Pb, Cd, Cr and Cu. Likewise, the possible relationship of the concentration of heavy metals with the color of the sample, level of magnetism and traffic density was studied. Contamination was evaluated using several indices such as contamination factor (CF), enrichment factor (EF), geoacumulation index (Igeo), pollutant load index (PLI) and ecological risk index (RI). A total of 88 samples were taken in the urban area of Cartagena, and the metals were determined by acid digestion and measured by inductively coupled plasma mass spectrometry. The concentration of heavy metals in urban dust from Cartagena was Zn (672 mg/kg) &gt; Cu (248.9 mg/kg) &gt; Pb (227 mg/kg) &gt; Cr (82.7 mg/kg) &gt; Ni (47.7 mg/kg) &gt; Cd (4.1 mg/kg). Contamination levels were high in Pb, Zn, Cd and Cu, according to environmental indices. A correlation was found between magnetism and metal concentration, which was repeated for all metals except Cd. Dark-colored samples contained higher metal concentrations than light-colored samples. Meanwhile, streets with medium and low traffic intensity were found to have higher concentrations of heavy metals. This study's objective was to identify pollution hotspots caused by heavy metals in dust in the urban ecosystem of Cartagena city.

. Shrub patches influence soil fertility and vegetation, impacting species composition and diversity. The Eastern Qilian Mountains' unique context provides insights into alpine ecosystems' response to environmental challenges. This study aimed to evaluate the physical characteristics and soil nutrient contents of shrub patches for four different shrub species. Four alpine shrub species (Salix oritrepha, Spiraea alpina, Rhododendron capitatum, and Potentilla fruticose) were studied, assessing their patch characteristics and soil nutrients at different depths within three patch microsites. Soil samples were collected and analyzed for organic matter, nitrogen, phosphorus, and potassium content. Statistical analyses were conducted to evaluate differences among shrub species and locations within the shrub patches. Our results showed that the shrub species exhibited variations in patch characteristics and soil nutrient distribution. Soil nutrient content varied by depth and location within the shrub patches, with higher concentrations at the center. The relative interaction intensity (RII) showed nutrient aggregation or dispersion trends. The study highlighted the complex interactions between shrub characteristics and soil nutrients, emphasizing their influence on nutrient cycling, vegetation dynamics, and soil properties. These findings contribute to our understanding of alpine ecosystem dynamics and inform conservation and management strategies.

Although mountain areas account for approximately one fifth of the terrestrial surface, there has been less research focused on fire in these areas compared to lowlands. Mountain fires have distinct behavior due to dynamic winds interacting with the terrain, which can influence the fireline intensity and propagation. For the sake of fire safety of fire crews, it is essential to know how difficult to control the fire is in the mountain regions, with fireline intensity providing a useful indicator of risk and suppressibility. We studied one of the major disasters, wildfire, in Australia in such a highland by using the Great Pine Tier Fire, which occurred 15^th January in 2019, ending up burning approximately 511.86km². Weather and fire intensity at pseudo weather stations located at key points of fire progression were analyzed by wind vector maps and numerical weather model vertical sounding (NWMVS). Fire propagation was then simulated in Prototype 2, a fire simulator capable of detecting the potential for lateral fire channeling (LFC), and simulating fireline intensity using Australian vegetation sub-models. We found that the synoptic wind appeared to be modified by the interaction with the terrain in windward and the fire intensified the most in its leeward. In practice, the fire moved out of the valley axis and up its sidehill by following the wind which had been modified by local vertex of the curved valley axis before reaching this location.

Atrophy quantification is fundamental for understanding brain development and diagnosing and monitoring brain diseases. FSL-SIENA is a well-known fully-automated method that has been widely used in brain magnetic resonance imaging studies. However, intensity variations arising during image acquisition that may compromise evaluation, analysis and even diagnosis. In this work, we study whether intensity standardisation can improve longitudinal atrophy quantification. We considered seven methods comprising z-score, fuzzy c-means, Gaussian mixture model, kernel density, histogram matching, white stripe, and removal of artificial voxel effects by linear regression (RAVEL). We used a total of 330 scans from two publicly-available datasets, ADNI and OASIS. In scan-rescan assessments, that measures robustness to subtle imaging variations, intensity standardisation did not compromise the robustness of FSL-SIENA significantly (p>0.1). In power analysis assessments, that measures the ability to discern between two groups of subjects, three methods led to consistent improvements in both datasets with respect to the original: fuzzy c-means, Gaussian mixture model, and kernel density estimation. Reduction in sample size using these three methods ranged from 17% to 95%. The performance of the other four methods was affected by spatial normalisation, skull stripping errors, presence of periventricular white matter hyperintensities, or tissue proportion variations over time. Our work evinces the relevance of appropriate intensity standardisation in longitudinal cerebral atrophy assessments using FSL-SIENA.

The assessment of the number of people exposed to natural hazards, especially in countries with strong urban growth, is difficult to be updated at the same rate as land use develops. This paper presents a remote sensing based procedure for quick updating the assessment of the population exposed to natural hazards. A relationship between satellite nightlights intensity and urbanization density from global available cartography is first assessed when all data are available. This can be used to extrapolate urbanization data at different time steps, updating exposure each time new nightlights intensity maps are available. As reliability test for the proposed methodology, the number of people exposed to riverine flood in Italy is assessed, deriving a probabilistic relationship between DMSP nightlights intensity and urbanization density from GUF database for the year 2011. People exposed to riverine flood are assessed crossing the population distributed on the derived urbanization density with flood hazard zones provided by ISPRA. The validation on reliable exposures derived from ISTAT data shows good agreement. The possibility to update exposure maps with higher refresh rate makes this approach particularly suitable for applications in developing countries, where exposure may change at sub-yearly scale.

The feasibility of a hurricane initialization framework based on the GSI-4DEnVar data assimilation system for the HWRF model is evaluated in this study. The system considers the temporal evolution of error covariances via the use of four-dimensional ensemble perturbations that are provided by high-resolution, self-consistent HWRF ensemble forecasts. It is different from the configuration of the GSI-3DEnVar data assimilation system, similar to that used in the operational HWRF, which employs background error covariances provided by coarser-resolution global ensembles from the NCEP GFS ensemble Kalman filtering data assimilation system. Data assimilation and numerical simulation experiments for Hurricanes Joaquin (2015), Patricia (2015), and Matthew (2016) are conducted during their intensity changes. The impacts of two initialization frameworks on the HWRF analyses and forecasts are compared. It is found that GSI-4DEnVar leads to a reduction in track, MSLP, and MSW forecast errors in all of the HWRF simulations, compared with the GSI-3DEnVar initialization framework. Further diagnoses with Hurricane Joaquin indicate that GSI-4DEnVar can significantly alleviate the imbalances in the initial conditions and enhance the performance of the data assimilation and subsequent hurricane intensity and precipitation forecasts.

Recently, light traps using light-emitting diode (LED) lights have been applied to monitor or control insect pests. The oriental armyworm, Mythimna separata Walker, is an important insect pest that has caused damage to several cereal crops, including corn, wheat and rice. The present study aims to seek out a sensitive wavelength causing high phototactic response in M. separata. The study evaluated the phototactic responses of M. separata moths to several LED lights of different wavelengths and luminance intensities under laboratory condition. Results showed that green (520 nm) LED light resulted in significant phototactic response of M. separata moths compared to LED lights of other wavelengths. Additionally, the highest attraction rate of the moths to green LED light appeared in luminance intensity group of 200 lux compared to the other intensities groups. Experiments under optimum conditions based on the above experiments revealed that the green LED light exhibited the strongest attraction rate (64.44%) among all experimental groups. An experiment performed in a net cage also showed that green LED light resulted in the highest phototactic response of M. separata moths, 1.7 times more than a commercial black light used as control. These findings clearly demonstrate that M. separata moths have a high sensitivity to the green LED light. Therefore, a light trap equipped with green LED light could be useful for monitoring and controlling M. separata moths.

Plants grown under fluctuating light impact plant developments compared with those grown under non-fluctuating light conditions. However, our knowledge on the underlying regulatory mechanisms is still quite limited, particularly from the transcriptional perspective. In order to investigate the influence of different light intensity distributions on tomato plant development, we designed three fluctuating light intensity distributions with the non-fluctuating light intensity as control and compared the transcriptional differences after five weeks of treatment. We found plant height and aerial/root weight were significantly reduced under all fluctuating light treatments. Transcriptome analysis revealed that the number of up and down regulated genes had a distinct distribution pattern between different treatments and control. The largest difference between the numbers of down and up regulated genes was found between treatment 1 and 3, reaching to a total of 416 genes. The number and type of the top 20 enriched pathways differed between treatments and control. The largest number of genes enriched was involved in the biosynthesis of secondary metabolites. These results provide insights into the transcriptional regulations of tomato under different light intensity distributions.

Various sudden shifts in financial market conditions over the past decades have demonstrated the significant impact of market structural breaks on firms' credit behavior. To characterize such effect quantitatively, we develop a continuous-time modulated Markov model for firms' credit rating transitions with the possibility of market structural breaks. The model takes a semi-parametric multiplicative regression form, in which the effects of firms' observable covariates and macroeconomic variables are represented parametrically and nonparametrically, respectively, and the frailty effects of unobserved firm-specific and market-wide variables are incorporated via the integration form of the model assumption. We further develop a mixtured-estimating-equation approach to make inference on the effect of market variations, baseline intensities of all firms' credit rating transitions, and rating transition intensities for each individual firm. We then use the developed model and inference procedure to analyze the monthly credit rating of U.S. firms from January 1986 to December 2012, and study the effect of market structural breaks on firms' credit rating transitions.

Super-high (x400) magnification dermoscopy (D400) is a new non-invasive imaging technique that has been shown to add information for the differential diagnosis of melanocytic lesions in a pilot study. Our study aimed to confirm if D400 can add details for the discrimination of clinically atypical nevus and melanoma. This is a retrospective observational, multicentric study enrolling patients who received an x20 (D20) and x400 (D400) magnification dermoscopic examination of pigmented skin lesions. Dermoscopic images were retrospectively evaluated by three observers for the presence/absence of nine D20 and twenty D400 dermoscopic features defined in the previous pilot study. Univariate and multivariate analyses were carried out to find predictors of benign and malignant behaviors. At D20 atypical pigment network, blue-whitish veil, atypical vascular pattern, regression, and homogenous pattern were more frequent in melanoma than in nevi (p&lt;0.001). At D400 melanoma showed more frequently than benign lesions melanocytes with an irregular arrangement and irregular in shape and size (p&lt;0.001). Network with edged papillae was more frequent in benign lesions than melanomas (p&lt;0.001). Our study confirms that D400 can identify melanocytes with an irregular arrangement and irregular in shape and size in melanomas, adding information to the conventional D20 examination.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

Historical analysis of Australian bushfire data spanning 170 years addresses whether the strength of recent fire events has been exacerbated by human-induced climate change. The question of “cause” looks at the characteristics of a wider range of natural hazards. Fire characteristics are compared with earthquake hazard characteristics: (1) energy – termed “magnitude”; (2) severity – termed “intensity”; and (3) resultant damage to people and structures – termed “impact”.Published global, Northern and Southern hemisphere temperature data are shown to vary consistently in phase over 170 years, but vary in amplitude with statistical significance. CO₂ levels north and south of the Equator have tracked quite consistently. Thus, Southern Hemisphere bushfire magnitude and intensity is compared with the Southern Hemisphere climate record, rather than a global data set.28 major bushfires and associated droughts since 1850 show neither apparent drought extent, nor area burned, nor bushfire intensity, correlates with changes in Southern Hemisphere climate. Average rainfall from 1900 shows a wetter, rather than drier trend. Cyclone energy shows no significant trend with climate. Planet-wide “greening”, through CO₂ fertilisation, is an insignificant contributor to bushfire magnitude. Combustion theory shows recorded “global warming” could have had no significant influence on bushfire magnitude or intensity. Any increase in Australian bushfire impact, as judged by lives lost, similarly, shows no correlation with bushfire magnitude, nor indeed, any observed Southern Hemisphere global warming.Thus, bushfire magnitude seems much more likely driven by fuel load and any anomalous bushfire intensity is likely driven by anomalous ground level fuel load. The evidence suggests that any CO₂ emissions reduction will have no impact on future bushfire “severity.