The aim of this research was to undertake laboratory testing to investigate the beneficial effects of epoxy resin grouts on the physical and mechanical properties of sands with a wide range of granulometric characteristics. Six sands, of different particle size and uniformity coefficients, were grouted using epoxy resin solutions with three ratios of epoxy resin to water (3.0, 2.0 and 1.5). A set of unconfined compressive strength tests were conducted on grouted samples at different curing periods and a set of long-term unconfined compressive creep tests in dry and wet conditions after 180 days of curing were also carried out, in order to evaluate the development of the mechanical properties of the sands, as well as, the impact of water on them. The findings of the investigation showed that epoxy resin resulted in appreciable strength values in the specimens, especially those of fine sands, grouted with the different epoxy resin grouts. In general, the compressive strength varied between 0.68 - 5.60 MPa and the modulus of elasticity between 75 - 480 MPa, after a curing period of 180 days. In terms of physical properties, the permeability and porosity (before and after the grouting process) were estimated. Grouts with an epoxy resin to water ratio of 3 decreased permeability by up to four orders of magnitude. Using laboratory results and regression analysis, three mathematical equations were developed that relate each of the dependent variables; compressive strength, elastic modulus, and coefficient of permeability, with particular explanatory variables.

Fracture grouting has been a widely used mitigation measure against seepage in the Yellow River Embankment. However, there is currently a lack of systematic investigation for evaluating the anti-seepage effectiveness of fracture grouting employed in this longest river embankment in China. Therefore, in this work, laboratory and in-situ experiments are carried out for investigating the reinforcement effect of fracture grouting in the Jinan Section of the Yellow River Embankment. In particular, firstly, the laboratory tests concentrate on studying the optimum strength improvement for cement-silicate grout by varying the content of backfilled fly ash and bentonite as admixtures. Flexural strength and Scanning Electron Microscope photographs are investigated for assessing the strength and compactness improvement. Subsequently, based on the obtained optimum admixtures content, in-situ grouting tests are carried out in the Jinan Section of the Yellow River Embankment to evaluate the anti-seepage effectiveness of fracture grouting, where geophysical prospecting and pit prospecting methods are employed. Laboratory results show that, compared with pure cement-silicate grouts, the gelation time of the improved slurry is longer and gelation time increases as fly ash content increases. The optimum mixing proportion of the compound cement-silicate grout is 70% cement, 25% fly ash and 5% bentonite, and the best volume ratio is 2 for the investigated cases. Geophysical prospecting using the Ground Penetrating Radar and High Density Resistivity methods can reflect the anti-seepage effectiveness of fracture grouting on site. It shows that the grouting material mainly flows along the axial direction of the embankment. The treatment that is used to generate directional fracture is proved to be effective. The injection hole interval distance is suggested to be 1.2 m, where the lapping effect of the grouting veins is relatively significant. For the investigated cases, the average thickness of the grouting veins is approximately 6.0 cm and the corresponding permeability coefficient is averagely 1.6 × 10⁻⁶ cm/s, which meets the anti-seepage criterion in practice.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

In the seasonally frozen regions, during the grouting of prestressed bridge ducts in low-temperature environments, incompletely cured grout materials undergo volumetric changes due to the freeze-thaw cycling, resulting in structural cracks along the prestressing ducts of the bridge, thereby diminishing the bridge's operational lifespan. To investigate the frost heaving characteristics of grout materials under freeze-thaw cycles and propose potential enhancements, this study was devised to conduct frost heaving stress tests on grout materials. Through this research, we gained insights into how various additives affect the frost heaving stress characteristics of grout materials under freeze-thaw cycles. Incorporating analyses of free water content, setting time, compressive strength, as well as macroscopic examinations such as XRD and SEM, this study delves into the mechanisms for enhancing frost heaving characteristics of grout materials. Furthermore, it proposes a research approach that utilizes multiple admixtures to improve the frost heaving properties of grout materials. Through frost heaving stress tests and other macroscopic experiments, the study investigates the influence of these combined admixtures on frost heaving stress in grout materials and elucidates the underlying improvement mechanisms. The results indicate that reducing the water-cement ratio, incorporating calcium formate, sulfoaluminate cement, air-entraining agents, and carbamide all have a positive impact on mitigating frost heaving stress in grout materials. However, the improvement mechanisms differ, and employing a single measure alone is insufficient to effectively reduce frost heaving stress while meeting performance criteria such as compressive strength, setting time, and flowability. Free water content emerges as a crucial indicator determining the magnitude of frost heaving stress in grout materials, with 11.5% of free water content representing the critical threshold for frost heaving in grout materials. Utilizing composite admixtures can simultaneously decrease free water content, lower the freezing point of free water, and alleviate frost heaving deformation, resulting in more efficient reduction of frost heaving stress. When the admixture content reaches 9.9%, frost heaving stress is eliminated, and the comprehensive performance parameters including compressive strength, setting time, and flowability meet the specified requirements.