The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

Wearable thermoelectric generators (w-TEGs) convert thermal energy into electrical energy to realize self-powering of intelligent electronic devices, thus reducing the burden of battery replacement and charging, and improving the usage time and efficiency of electronic devices. Through finite element simulation, this study successfully designed high-performance thermoelectric generator and made it into wearable thermoelectric module by adopting “rigid device - flexible connection” method. It was found that higher convective heat transfer coefficient on cold-end leads to larger effective temperature difference and better power generation performance of device in typical wearable scenario. Meanwhile, at same convective heat transfer coefficient on the cold-end, longer TE leg length leads to larger temperature difference established at both ends of device, larger device output power and open-circuit voltage. However, when the convective heat transfer coefficient increases to a certain level, optimization effect of increasing TE leg length on device power generation performance will gradually diminish. For devices with fixed temperature difference between two ends, longer TE leg length leads to higher resistance of TEG, resulting in lower device output power but slight increase in open-circuit voltage. Finally, sixteen 16×4×2 mm2 TEGs (L=1.38 mm, W=0.6 mm) and two modules were fabricated and tested. At hot end temperature Th=33 ℃ and cold end temperature Tc=30 ℃, the actual maximum output power Pout of TEG is about 0.2 mW, and the actual maximum output power Pout of TEG module is about 1.602 mW, which is highly consistent with the simulated value. This work brings great convenience to research and development of wearable thermoelectric modules and provides new, environmentally friendly and efficient power solution for wearable devices.

Nowadays the practice of developing algorithms to maintain the confidentiality of data shows that there is a lack of some features, such as velocity, predictability, etc. Generating pseudorandom numbers is one such problem that lies in the basement of many algorithms, even in hardware microprograms. An unreliable generator can cause cyberattacks on it, despite the security in the upper layers. At the same time, the algorithm should be fast enough to provide uninterrupted circuit work for the entire system. The paper presents a new algorithm generating pseudorandom numbers on cellular automata, which is not only fast and easy-repeating, but unpredictable enough and can be used in cryptographic systems. Using the NIST statistical test suite for random and pseudorandom number generators (PRNG), it is shown that the presented algorithm is more than three times superior to the state-of-the-art methods and algorithms in terms of ? − ?????. A high level of the presented algorithm’s parallelization allows for implementation it effectively on calculators with parallel structure. CPU-based architecture, FPGA-based architecture, CUDA- based architecture of PRNG and different PRNG implementations are presented to confirm high performance of the proposed solution.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

Osteosarcoma (OS) are the most prevalent malignant bone tumors in adolescents and young adults.. OS cells grow in a permissive local microenvironment which modulates their behavior and facilitates all steps in tumor development (e.g., proliferation/quiescence, invasion/migration, drug resistance) and contributes to their intrinsic heterogeneity. The lung parenchyma is the most common metastatic site in OS, and metastatic foci are frequently associated with a poor clinical outcome. Although multiple factors may be responsible for the disease, including genetic mutations (e.g., Rb, p53), the molecular mechanism of development of OS remains unclear and the conventional treatment for OS is still based on a sequential approach that combines chemotherapy and surgery. Also, despite the increase in clinical trials, the survival rates for OS have not improved. Non-specific targeting therapies thus show poor therapeutic effects with side effects at high doses. For these reasons, many efforts have been done to characterize the complex genome of osteosarcoma thanks to the whole exome analysis with the aim to identify predictive biomarkers to give to these patients a better therapeutic option. This review aims to summarize and discuss the main recent advances in OS molecular research for precision medicine.

Advanced lithography requires highly sensitive photoresists to improve lithographic efficiency, and it is critical yet challenging to develop high-sensitivity photoresists and imaging strategies. Here, we report a novel strategy for ultra-high sensitivity using hexafluoroisopropanol (HFIP)-containing fluoropolymer photoresists. The incorporation of HFIP, with its strong electrophilic property and electron-withdrawing effect of the fluorine atoms, significantly increases the acidity of the photoresist after exposure, enabling imaging without conventional photoacid generators (PAGs). The HFIP-containing photoresist has been evaluated by electron beam lithography to achieve a trench of ~40 nm at an extremely low dose of 3 μC/cm2, which shows sensitivity enhancement by ~10 times to the commercial PAGs involved system, revealing its high-sensitivity and high-resolution features. Our results demonstrate a new type of PAGs and a novel approach to higher-performance imaging beyond conventional photoresist performance tuning.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

In this paper, the stabilization and high efficiency of an unstable Second Harmonic Generation (SHG) of a Nd : YVO4 laser with a KTP intracavity is carried out by using a passive Q-switching crystal and a parametric modulation method (harmonic modulation) is shown. The harmonic modulation was defined as um(t) = Amsin(2π fmt), with modulation amplitude as Am(Vpp), and modulation frequency as fm(Hz), applied to the pumping of the Nd : YVO4 -KTP laser to control the amplitude and frequency of the emission, thus stabilizing the dynamic states of this laser. The promising application of this green light source is materialized when such light is necessary for high-density optics, such as in the treatment materials industry or in some aesthetic applications.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Pancreatic cancer stands out as one of the most lethal forms of malignancies, representing 2% of all cancer cases and contributing to 5% of cancer-related fatalities. Therefore, early detection of pancreatic cancer is crucial for enhancing treatment outcomes. Various hereditary cancer syndromes have been linked to an elevated risk of developing pancreatic cancer, suggesting potential benefits from surveillance strategies for individuals at risk. Presently, precision medicine employs PARP inhibitor therapy for pancreatic cancer patients carrying germline variants in Homologous Recombination Repair (HRR) genes. Our objective was to ascertain the occurrence of germline pathogenic/likely pathogenic variants in genes predisposing to cancer among pancreatic cancer patients. Methodologically, we analyzed 184 pancreatic cancer patients referred to our laboratory for genetic examination. Utilizing a Next-Generation Sequencing (NGS) approach, we scrutinized 52 genes implicated in hereditary cancer predisposition. Our findings revealed that 21% of the patients analyzed harbored germline pathogenic/likely pathogenic variants. Within this subset, 48% exhibited positive results in pancreatic cancer susceptibility genes, namely ATM (17%), BRCA1 (12%), BRCA2 (7%), CDKN2A (7%), and PALB2. Significantly, 64.3% of the pathogenic variants were associated with genes involved in the HRR pathway (ATM, BRCA1, BRCA2, BRIP1, CHEK2, FANCL, MRE11, PALB2, RAD50, RAD51B and RAD51C). In conclusion, our study underscores the significance of multigene genetic testing for pancreatic cancer patients, with 21% of individuals yielding findings linked to pancreatic or other cancer predisposition. Moreover, patients carried pathogenic/likely pathogenic variants in HRR genes, potentially benefiting from targeted therapies such as PARP inhibitors or platinum-based treatments.

Modern electrical power systems integrate renewable generation, with solar generation being one of the pioneers worldwide. In Latin America, the greatest potential and development of solar generation is found in Chile through the National Electric System. However, its energy matrix faces a crisis of drought and reduction of emissions that limits hydroelectric generation and involves the definitive withdrawal of coal generation. The dispatch of these plants is carried out by the system operator, who uses a simplified mechanism, called “economic merit list” and which does not reflect the real costs of the plants to the damage of the operating and marginal cost of the system. This inefficient dispatch scheme fails to optimize the availability of stored gas and its use over time. Therefore, a real-time redispatch model is proposed that minimizes the operation cost function of the power plants, integrating the variable generation cost as a polynomial function of the net specific fuel consumption, adding gas volume stock restrictions and water reservoirs. In addition, the redispatch model uses an innovative "maximum dispatch power" restriction, which depends on the demand associated with the automatic load disconnection scheme due to low frequency. Finally, by testing real simulation cases, the redispatch model manages to optimize the operation and dispatch costs of power plants, allowing the technical barriers of the market to be broken down with the aim of integrating ancillary services in the short term, using the power reserves in primary (PFC), secondary (SCF), and tertiary (TCF) frequency control.

MicroRNAs (miRNAs) are crucial regulatory RNAs, originated from hairpin precursors. For the past decade, researchers are focusing extensively on miRNA profiles in various plants. However studies on precursor miRNAs (pre-miRNAs) global profiling stay static even in model plants. Here, for the first time in a non-model plant, Abelmoschus esculentus with negligible genome information, we are reporting the global profiling to characterize the miRNAs and their associated pre-miRNAs by applying next generation sequencing approach. Preliminarily we performed sRNA (small RNA) sequencing with five biological replicates of leaf samples to attain 207,285,863 reads and data analysis using miRPlant keyed out 128 known and 845 novel miRNA candidates. With the objective to seize their associated hairpin precursors, we accomplished pre-miRNA sequencing to attain 83,269,844 reads. The paired end reads are merged, adaptor trimmed and the resulting 40-241 nt (nucleotide) sequences were picked out for analysis by using perl scripts from miRGrep tool and in-house built shell script for Minimum Fold Energy Index (MFEI) calculation. Applying stringent criteria of dicer cleavage pattern and perfect stem loop structure revealed precursors for 57 known miRNAs of 15 families and 18 novel miRNAs. Quantitative Real Time (qRT) PCR was performed to determine the expression of selected miRNAs.

The interaction of electrons with strong laser fields is usually treated with semiclassical theory, where the laser is represented by an external field. There are analytic solutions for the free electron wave functions, which incorporate the interaction with the laser field exactly, but the joint effect of the atomic binding potential presents an obstacle for the analysis. Moreover, the radiation is a dynamical system, the number of photons changes during the interactions. Thus, it is legitimate to ask how can one treat the high order processes nonperturbatively, in such a way that the electron-atom interaction and the quantized nature of radiation be simultaneously taken into account? An analytic method is proposed to answer this question in the framework of nonrelativistic quantum electrodynamics. As an application, a quantum optical generalization of the strong-field Kramers-Heisenberg formula is derived for describing high-harmonic generation. Our formalism is suitable to analyse, among various quantal effects, the possible role of arbitrary photon statistics of the incoming field. The present paper is dedicated to the memory of Prof. Dr. Fritz Ehlotzky, who had significantly contributed to the theory of strong-field phenomena over many decades.

During the last two decades several cases of venous thrombosis (VTE) after a prolonged period at a computer has been described, denominated “eThrombosis”. Video gaming on a computer has become very popular and can be a social activity where several players are gathered to play against each other or in a virtual environment for several days (“LAN (i.e., Local Area Network) parties”) where the participants are sedentary and consuming calorie-rich food items. The aim of this study was to investigate a potential coagulation activation during a 42 hour LAN party. Nine male gamers volunteered for the LAN party. Citrated blood was sampled before and every 6 hours, and plasma was analyzed for thrombin generation, and Thrombin-antithrombin-complexes (TAT), prothrombin Fragment 1+2 (F1+2), and D-dimer. Thrombin generation increased slightly but not significantly during the LAN party, whereas the coagulation activation markers were unchanged. These results do not indicate that the coagulation system is activated significantly during 42 h gaming with minimal physical activity. Although an increased activity cannot be excluded, it does not directly indicate a risk of VTE in general. It may be specific and particularly susceptible in-dividuals who are prone to thrombosis and, therefore, are at risk of developing e-thrombosis.

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

Nowadays, energy decarbonization due to the integration of renewable energy sources presents important challenges to overcome. The intermittent nature of photovoltaic systems reduces power quality by producing voltage variations and frequency deviations in electrical systems networks, especially, in weak and isolated distribution systems in developing countries. This paper presents a power smoothing method improving the low pass filter and moving average for grid-connected photovoltaic system, the novel method includes state-of-charge monitoring control of the supercapacitors energy storage system to reduce the fluctuations of photovoltaic power at the point of common coupling. A case study for a microgrid in a high-altitude city in Ecuador is presented with exhaustive laboratory tests using real data. The ultimate goal of this research is to improve energy power quality in electrical distribution systems to cope with the growth of renewable penetration.

Analyzing BRCA1/2 tumor pathogenic variants (TPVs) in epithelial tubal/ovarian cancers (EOC) has become an essential part of the diagnostic workflow in many centers to guide treatment options and genetic cascade testing. However, there is no standardization of testing procedures, including techniques, gene assays, or sequencers used, and data on the execution of tumor tests remains scarce. Therefore, we evaluated characteristics of BRCA1/2 tumor testing in advanced-stage EOC with real-world national data. Pathology reports of patients diagnosed with EOC in 2019 in the Netherlands were obtained from the Dutch Pathology Registry (PALGA), and data regarding histological subtype and BRCA1/2 tumor tests were extracted. A total of 999 patients with advanced-stage EOC were included. Tumor tests were performed for 502 patients (50.2%) and BRCA1/2 TPVs were detected in 14.7%. Of all tests, 48.6% used hybrid capture techniques and 26.5% used PCR-based techniques. More than half of the tests (55.0%) analyzed other genes in addition to BRCA1/2. Overall, this study highlights the heterogeneity in the execution of BRCA1/2 tumor tests. Despite a lack of evidence of quality differences, we emphasize that adequate reporting and internal and external quality monitors are essential for high-quality implementation and execution of reliable BRCA1/2 tumor testing, which is crucial for identifying all patients with BRCA1/2 TPVs.

This research explores the behaviors of Generation Z consumers in China, particularly focusing on their interaction with companies through social media for the joint creation of value. Adopting a qualitative methodology, the research initially constructs a scale for assessing co-creation of value on social media platforms. Subsequently, it delves into the motivational aspects of users' engagement in these co-creative activities. The study unveils a range of utilitarian and hedonic motivations that drive Generation Z's value co-creation actions on social media. Insights derived from the findings offer both theoretical and practical implications for the field.

The valley pseudospin properties of electrons in two–dimensional hexagonal materials result in lots of fascinating physical phenomena, which opens up the new field of valleytronics. The valley-contrasting physics aims at distinguishing the valley degree of freedom based on valley–dependent effects. Here, we theoretically demonstrate that both of the valley–selective high harmonic generation and valley–selective electronic excitation can be achieved by using an orthogonal two–color (OTC) laser field in gapped graphene. It is shown that the asymmetry degrees of harmonic yields in the plateaus, cutoff energies of generated harmonics and electron populations from two different valleys can be precisely controlled by the relative phase of the OTC laser field. Thus the selectivity of the dominant valley for the harmonic radiation and electronic polarization can be switched by adjusting the relative phase of the OTC laser field. Our work offers an all–optical route to produce the valley–resolved high harmonic emissions and manipulate the ultrafast valley polarization on a femtosecond timescale in condensed matter.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

Entropy generation, formulated by combining the first and second laws of thermodynamics with an appropriate thermodynamic potential, emerges as the difference between a phenomenological entropy function and a reversible entropy function. The phenomenological entropy function is evaluated over an irreversible path through thermodynamic state space via real time measurements of thermodynamic states. The reversible entropy function is calculated along an ideal reversible path through the same state space. Entropy generation models for various classes of systems—thermal, externally loaded, internally reactive, open and closed––are developed via selection of suitable thermodynamic potentials. Here we simplify thermodynamic principles to specify convenient and consistently accurate system governing equations and characterization models. The formulations introduce a new and universal Phenomenological Entropy Generation (PEG) theorem. The systems and methods presented––and demonstrated on grease degradation, battery charging and discharging, metal fatigue and pump flow––can be used for design, analysis, and support of diagnostic monitoring and optimization.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

High resolution information on nucleotide arrangement in the genome of any or-ganism is critical to understand its genetic makeup, function, and evolutionary his-tory. For years, DNA sequencing has provided crucial breakthroughs in the field of genomics and molecular biology. With the advent of technology, Next Generation Sequencing has now transformed the whole genome sequencing prospects, thus unveiling the novel and interesting features of an organism genome that can behold. Next generation sequencing platforms offer realistic approach to identify and anal-yses whole genome with high throughput, accuracy, scalability in a very short time span. Information obtained can be further used in improving our existing healthcare systems, designing novel and personalized therapeutic modules, making the envi-ronment sustainable and proactively preparing ourselves for future pandemics and outbreaks. This article discusses the various NGS technologies and approaches, their advantages, drawbacks, and futuristic usage in different fields. Though still in nascent stages and marred with flaws, with ongoing advancement, NGS will indeed have promising impacts in the future.

Circulating cell-free DNA (cfDNA) refers to small fragments of DNA molecules released after programmed cell death and necrosis in several body fluids such as blood, saliva, urine, and cerebrospinal fluid. The discovery of cfDNA has revolutionized the field of non-invasive diagnostics in the oncologic field, in prenatal testing, and in organ transplantation. Despite the potential of cfDNA and the solid results published in recent literature, several challenges remain, represented by low abundance, need for highly sensitive assays and analytical issues. In this review, the main technical advances in cfDNA analysis are presented and discussed, with a comprehensive examination of the current available methodologies applied in each field. Considering the potential advantages of cfDNA, this biomarker is increasing its consensus among clinicians, as it consents to monitor patients’ conditions in an easy and non-invasive way, offering a more personalized care. Nevertheless, cfDNA analysis is still considered a research marker to be further validated, and very few centers are implementing its analysis in the real-life assistance. As technical improvements are enhancing the performances of cfDNA analysis, its application will transversally improve patients’ quality of life.

In recent years, the focus of disease resistance and susceptibility studies in cattle have been on determining patterns in the innate immune response of key proteins, such as Toll-like receptors (TLR). In the bovine genome, there are 10 TLR family members and, of these, TLR2, TLR4 and TLR6 are specialized in recognition of bacterial ligands. Indigenous cattle breeds of Anatolia have been reported to show fewer signs of clinical bacterial infections, such as bovine tuberculosis and mastitis, and it is hypothesized that this might be due to a less stringent genetic selection during breeding. In contrast, Holstein-Friesian cattle have been under strong selection for milk production, which may have resulted in greater susceptibility to diseases. To test this hypothesis, we have compared the TLR2, TLR4 and TLR6 genes of Anatolian Black (AB), East Anatolian Red (EAR), South Anatolian Red (SAR), Turkish Grey (TG), and Holstein (HOL) cattle using Next Generation Sequencing. The SAR breed had the most variations overall, followed by EAR, AB, TG and HOL. TG had the most variations for TLR2 whereas SAR had the most variations in TLR4 and TLR6. We compared these variants with those associated with disease and susceptibility traits. We used exon variants to construct haplotypes, investigated shared haplotypes within breeds and determined candidate haplotypes for disease resistance phenotype in Anatolian cattle breeds.

In the current paper, a residual generation filter with finite memory structure is proposed for sensor fault detection. The proposed finite memory residual generation filter provides the residual by real-time filtering of fault vector using only the most recent finite observations and inputs on the window. It is shown that the residual given by the proposed residual generation filter provides the exact fault for noise-free systems. The proposed residual generation filter is specified to the digital filter structure for the amenability to hardware implementation. Finally, to illustrate the capability of the proposed residual generation filter, numerical examples are performed for the discretized DC motor system having the multiple sensor faults.

Abstract: Power generation using dielectric elastomer (DE) artificial muscle is attracting attention because of its light weight, low cost, and high efficiency. Since this method is a system that produces electricity without emitting carbon dioxide nor using rare earths, it would contribute to the goal of environmental sustainability. In this paper, the background of DEs, the associated high-efficient wave energy generation (WEG) systems that we developed using DEs, as well as the latest development of its material are summarized. By covering the challenges we face and the achievements that we’ve reached, we can discuss the opportunities to build the foundation of a recycled energy society through the usage of these WEGs. On the other hand, to make these possibilities commercially successful, the advantages of DEs need to be integrated with traditional technologies. To achieve this, we also consider the method of using DEs alone and a system used in combination with an oscillating water column. Finally, the current status and future of DEGs are discussed.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

Flammability was evaluated and the results showed the values of critical flux at extinguishment (CFE) as 49.5kW/㎡ on average, total heat release (Qt) as 0.21MJ on average, and peak heat release rate (Qp) as 0.66kW on average, which satisfied all of the thresholds presented by the IMO. Therefore, flame-retardant plywood, of which the flame-retardant performance was evaluated, was determined to be an applicable finishing material that satisfies fire safety standards.

Homologous recombination deficiency (HRD) has become an important prognostic and predictive biomarker for patients with high-grade serous ovarian cancer who may benefit from poly-ADP ribose polymerase inhibitors (PARPi) and platinum-based therapies. HRD testing provides relevant information to personalize patients’ treatment options, and it has been progressively incorporated in diagnostic laboratories. In this study, we evaluated the feasibility of in-house HRD testing deployable in a diagnostic clinical setting, comparing results from two commercially available next-generation sequencing (NGS)-based tumor tests (SOPHiA DDMTM HRD Solution and AmoyDx HRD Focus Panel) with the reference assay from Myriad MyChoice CDx. A total of 85 ovarian cancer samples were subjected to HRD testing. An overall strong correlation was observed across the three assays evaluated, regardless of the different underlying methods employed to assess genomic instability, with the highest pairwise correlation between Myriad and SOPHiA (R=0.87, p-value=3.39x10-19). The comparison of the assigned HRD status to the reference Myriad’s test revealed a positive predictive value (PPV) and negative predictive value (NPV) of 90.9% and 96.3% for SOPHiA’s test, while AmoyDx’s test achieved 75% PPV and 100% NPV. This is the largest HRD testing evaluation using different methodologies and provides a clear picture of the robustness of NGS-based tests currently offered in the market. Our data show that the implementation of in-house HRD testing in diagnostic laboratories is technically feasible and it can be reliably performed with commercial assays. Also, the turnaround time is compatible with clinical needs, being an ideal alternative to offer to a broader number of patients, while still maintaining high-quality standards at more accessible price tiers.

Technological developments, as a result of globalization, indirectly affect human lifestyles, one of which is the Indonesian people. In a situation of change towards the Industrial Revolution 4.0, Pancasila has a role as a guide for the Indonesian people to be what by the noble values ​​of the nation. However, the role of the millennial generation in maintaining these noble values ​​is important considering that they are the spearhead of the country's development. From this statement, this study aims to identify and formulate steps to maintain the noble values ​​of Pancasila among the millennial generation so that it does not eliminate national identity and understand the urgency of implementing the Pancasila lifestyle in the era of globalization. By using the literature review method, it can be seen that "grounding" and strengthening the essence of Pancasila values ​​can be a solution so that the existence of Pancasila continues to shine. The Pancasila lifestyle deserves to be implemented because it regulates all behaviors of speech, thought, behavior, action, and good manners so that it must be expressed in the life of the nation and state as well as our everyday life.

This paper presents a robust and efficient fault detection and diagnosis framework for handling small faults and oscillations in synchronous generator (SG) systems. The proposed framework utilizes the Brunovsky form representation of nonlinear systems to mathematically formulate the fault detection problem. A differential-flatness model of SG systems is provided to meet the conditions of the Brunovsky form representation. A combination of high-gain observer and group method of data handling neural network is employed to estimate the trajectory of the system and to learn/ approximate the fault and uncertainties associated functions. The fault detection mechanism is developed based on output residual generation and monitoring so that any unfavourable oscillation and/or fault occurrence can be detected rapidly. Accordingly, an average L1-norm criterion is proposed for rapid decision making of faulty situations. The performance of the proposed framework is investigated for two benchmark scenarios which are actuation fault and fault impact on system dynamics. The simulation results demonstrate the capacity and effectiveness of the proposed solution for rapid fault detection and diagnosis in SG systems in practice, and thus enhancing service maintenance, protection, and life cycle of SGs.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

The rising importance of Big Data in modern information analysis is supported by vast quantities of user data, but it is only possible to collect sufficient data for all tasks within certain data-gathering contexts. There are many cases where a domain is too novel, too niche, or too sparsely collected to adequately support Big Data tasks. To remedy this, we have created ADG Engine that allows for the generation of additional data that follows the trends and patterns of the data that’s already been collected. Using a database structure that tracks users across different activity types, ADG Engine can use all available information to maximize the authenticity of the generated data. Our efforts are particularly geared towards data analytics by identifying abnormalities in the data and allowing the user to generate normal and abnormal data at custom ratios. In situations where it would be impractical or impossible to expand the available dataset by collecting more data, it can still be possible to move forward with algorithmically expanded data datasets.

This paper introduces an innovative energy circuit that challenges conventional understandings of energy conservation, marking a significant departure from traditional frameworks. Seeking to enhance energy generation within existing paradigms, this innovation holds promise for addressing pressing global issues such as the energy crisis and environmental sustainability, while also stimulating scientific inquiry. In contrast to prevalent misconceptions rooted in philosophical and scientific constraints, this study refutes the notion of generating energy from nothing and questions the viability of perpetual motion machines as conceptual models. Instead, it proposes a novel circuit design derived from an unconventional electrical short circuit, which is shown to disrupt the established principles of energy conservation. This circuit offers a transformative approach with diverse applications, including self-recharging capabilities for electric vehicles, bolstering microgrid infrastructure, and facilitating the integration of renewable energy sources. Transcending conventional scientific boundaries, this paper prompts philosophical reflections on the evolving nature of scientific exploration. Ultimately, the energy circuit represents a pivotal step towards mitigating the global energy crisis by reducing reliance on finite resources and fostering sustainability. The paper concludes by illustrating the circuit's potential to revolutionize energy systems and contribute to a more resilient and sustainable future.

We discuss a formalism which allows for the calculation of a higher harmonic current response to an applied electric field for disordered superconducting systems described on the basis of tight-binding models. The theory is based on an expansion of the density matrix in powers of the field amplitudes where we solve the equation of motion for the individual components. This allows the evaluation of higher order response functions on significantly larger lattices than one can achieve with a previously used approach, which is based on a direct temporal integration of the equation of motion for the complete density matrix. In case of small lattices, where both methods can be applied by including also the contribution of collective modes, we demonstrate the agreement of the corresponding results.

Introduction: Indonesia consists of a plural society with different ethnic, religious, racial, skin color, and other cultures. The difference must be understood by everyone, especially the younger generation in the digital age. If the younger generation does not have a sufficient understanding of multicultural education values, it will impact the moral crisis of the Indonesian nation. This research emphasizes the importance of multicultural education to the younger generation to understand the differences (pluralism) in society and respect them. Method: The method uses a qualitative method with the literature review method by collecting data on ten journals published in 2019, 2020, 2021. Results: The rise of socio-cultural conflicts in Indonesia is why applying multicultural values to the younger generation. Multiculturalism is needed to establish morals and sensitivity for a young person in the face of various social problems and symptoms at a growing age. Conclusion: Multicultural education is vital to the younger generation considering Indonesia has diverse nations and cultures. The efforts that can make to improve the morale of the nation's children, namely by learning citizenship education and religious education and utilizing information technology to spread things related to the values of multicultural education to the broader community

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

In present work, the effects of bioflavonoids (ginkgetin and sciadopitysin) on stimulus-induced superoxide generation, tyrosyl and serine/threonine phosphorylation of proteins in human neutrophils, and the translocation of cytosolic compounds (p47phox, p67phox and Rac) to cell membrane were studied, which were isolated from the needles of Taxus media var. Hicksii. Meanwhile, three normal flavonoids (apigenin, quercetin and isoquercetin) were involved as contrasts. The results indicated that ginkgetin and sciadopitysin were capable of concentration-dependently inhibitory effects on the superoxide generation induced by N-formyl-methionyl-leucyl-phenylalanine (fMLP), arachidonic acid (AA) and phorbol-12-myristate 13-acetate (PMA). And they also suppressed fMLP- and AA- induced tyrosyl or PMA-induced serine/threonine phosphorylation and the translocation of cytosolic compounds (p47phox, p67phox and Rac) to cell membrane, which were in parallel with the suppression of the stimulus-induced superoxide generation. The effect of these compounds on the radical-scavenging was also investigated. Ginkgetin and sciadopitysin did not show remarkable effect on DPPH radical-scavenging activity, and they didn’t display the radical-scavenging activity on superoxide anion generated by phenagine methoxysulfate (PMS)-NADH system. Apparently, ginkgetin and sciadopitysin had great performance in pharmacological value and they are worthy of in-depth study.

this paper we present approaches for generating random numbers along with potential applications. Rather than trying to provide extensive coverage of several techniques or algorithms that have appeared in the scientific literature, we focus on some representative approaches presenting their workings and properties in detail. Our goal is to delineate their strengths and weaknesses as well as their potential application domains so as the reader can judge what would be the best approach for the application in hand, possibly a combination of the available approaches. For instance, a physical source of randomness can be used for the initial seed, then suitable preprocessing can enhance its randomness and then the output of the preprocessing can feed different types of generators, e.g. a linear congruential generator, a cryptographically secure one and one based on the combination of one way hash functions and shared key cryptoalgorithms in various modes of operation. Then, if desired, the outputs of the different generators can be combined giving the final random sequence. Moreover, we present a set of practical randomness tests which can be applied on the outputs of random number generators in order to assess their randomness characteristics. In order to demonstrate the importance of unpredictable random sequences, we present an application of cryptographically secure generators in domains where unpredictability is one of the major requirements, i.e. eLotteries and cryptographic key generation.

Background : The current corruption case in Indonesia are severely problematic since it is normalized by society. As a response, the current agenda of the Indonesian government to tackle it is by raising awareness of youth towards Indonesia’s corruption case. Aim : This study aims to knowing the importance of anti-corruption education and its applications among students. Method : The methodology of this study is the use of a qualitative survey on Faculty of Pharmacy students and interviews with representatives of students of the Faculty of Pharmacy. The population of this study is students of Airlangga University. The sample of this study is 52 students of class C the Faculty of Pharmacy Result : Students have awareness about corruption and even proposed that the current anti-corruption education is not enough to tackle corruption. Recommendation : The researcher suggests that students can be brave to campaign about the importance of anti-corruption education to the public. Limitation : The limitation of this study is that it is difficult to conduct research because in the online pandemic era, this results in delays in the research process.

Pancasila is the identity of the Indonesian nation, which means that Pancasila is a national characteristic that cannot be found in any country. Pancasila points are taken from the noble values of the Indonesian state. These principles contain culture, customs, and national character known as manners, cooperation, and high nationalism. As the successor to Indonesian culture, the young generation must be able to preserve and develop Pancasila. In this era of globalization, there are many challenges for the younger generation in preserving Pancasila. This study aims to provide an overview of the decline of Pancasila identity among the younger generation due to the impact of globalization. The research question that has been determined is how the practice behaviour of the younger generation towards the implementation of Pancasila, the solutions and efforts that all Indonesian people can make regarding the crisis of Pancasila identity in the era of globalization. This research method uses a literature review. The research sources were conducted from the latest journals and books published in 2019 until 2021 related to the theme of Pancasila and the millennial generation. The results showed that globalization has greatly facilitated foreign cultures to enter Indonesia. The younger generations use this foreign culture as a lifestyle without filtering it, whether it contains Pancasila values or not. This causes Pancasila has been forgotten and no longer applied in their everyday life. Young people can make various efforts to preserve the national identity, namely Pancasila. Apart from the role of the young generation itself, Indonesian society can also play an essential role in supporting the younger generation to continue implementing Pancasila in their lives. By conducting this research, it is hoped that Indonesia's young generation can understand, select, and stay away from the negative impacts of globalization that enter Indonesia freely. The solution that can be given from this research is that the younger generation must love their own culture more and practice every principle in Pancasila. Parents, educational institutions, and the government must also support the younger generation to maintain national identity, Pancasila values. The limitation of this research is that the researcher did not conduct any primary data, which means the data were not directly from the source. This causes the accuracy of this study to be less guaranteed. The recommendation that the researchers can give for further research is to obtain primary data to ensure accuracy and explore research topics regarding the fading of Pancasila identity in the younger generation in this era of globalization.

In this paper, we revisit the hydrodynamics supporting the design and development of the RiverCat class of catamaran ferries operating in Sydney Harbor since 1991. More advanced software is used here. This software accounts for the hydrodynamics of the transom demisterns which experience partial or full ventilation, depending on the vessel speed. This ventilation gives rise to the hydrostatic drag, which adds to the total drag of the vessel. The presence of the transom also creates a hollow in the water. This hollow causes an effective hydrodynamic lengthening of the vessel, which leads to a reduction in the wave resistance. Hence a detailed analysis is required in order to optimize the size of the transom. It is demonstrated that the drag of the vessel and the wave generation can be predicted with good accuracy. Finally, the software is also used to optimize the vessel further by means of affine transformations of the hull geometry.

When a microgrid is grid-tied to a distribution system, it can provide surplus power generation to the distribution system, if any abnormality or interruption occurs in the distribution system, the microgrid can operate in standalone mode to isolate the impact of the abnormality or interruption. However, if the microgrid can not collect enough information from the distribution system, it may cause the failure of generation transferring of distribution feeders, or even further influence the stability of the distribution system. In this paper, a strategy for the resilient control of a microgrid is proposed. It can solve the above-mentioned problem, reduce the duration of the outage of loads. This strategy is experimented in the microgrid in the Institute of Nuclear Energy Research (INER), the reliability is also analyzed to evaluate the unavailability of the microgrid in INER, and it is verified that the proposed strategy can reduce the duration of the outage of loads, and hence the reliability of a microgrid can be upgraded.

New challenges arise in the face of global climate change which impact every ecosystem on earth, including aquatic systems. This is evident in observations made in regard to the world’s oceans, which show trends of incremental changes in ocean surface temperatures, sea levels, and ocean acidity. These environmental shifts impact human resources such as fisheries and aquaculture. In addition, according to the World Bank, the increase in human population will also require more food and nutrient production, which include industries such as aquaculture. With this increasing demand in aquaculture and fisheries, we must develop efficient and productive methods to operate these industries. We can use genetic methods, specifically transcriptomic information to better understand the biology of our source of nutrition. With the advent of RNASeq techniques, we can provide a better understanding about growth and development, immune function and stress, and adaptations. The use of population genetics or (genomics) to detect Single Nucleotide Polymorphisms (SNPs) between populations or closely related species can provide greater insight from stock structure to fishery-induced evolution. In addition, candidate loci can be investigated further to better understanding evolutionary processes, which provide clues on physiological adaptations and gene expression patterns that can help elucidate how these organisms respond to their current environment. In addition, the use of transcriptomic analyses such as differential gene expression can be used to determine resilience in various environmental conditions such as pollution, hypoxic/anoxic conditions, fluctuations in salinity, and temperature extremes. There has been an increase in transcriptomic studies for many aquaculture species, which has aimed at improving our understanding of growth, development, and metabolism, providing vital information for fisheries and aquaculture industries to make adjustments to environmental conditions such as oxygen availability, nutrition, and salinity. All of these aspects provide insightful information for advancing our knowledge of aquaculture, fisheries and conservation management.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

As the international community attaches importance to environmental and climate issues, carbon dioxide emissions in various countries have been subject to constraints and limits. Carbon trading market, as a market tool to reduce greenhouse gas emissions, has gone through a development process from a pilot carbon market to a national carbon market in China. At present, the industries included in the national carbon market are mainly the electric power industry, and the carbon emissions of the electric power industry account for about 40% of the national carbon emissions. According to the construction history of foreign carbon markets, China's future carbon quota allocation will gradually transition from free allocation to auction allocation,the auction mechanism will bring a heavy economic burden to the electric power industry, especially the thermal power generation industry. Therefore, this study takes Guangdong Province as an example to optimize the power generation mix with the objective of minimizing the total economic cost after the innovative introduction of the carbon quota auction mechanism and constructs an optimization model of the power generation mix based on the auction ratio by comprehensively applying the system dynamics model and the multi-objective linear programming model and systematically researches the power generation structure under different auction ratios with the time scale of months and quantitatively evaluates the economic inputs needed to reduce the greenhouse gas emissions.The results of the study show that after comprehensively comparing the total economic cost, renewable energy development and carbon emissions, it is the most scientific and reasonable to set the auction ratio of carbon allowances at 20%, which achieves the best level of economic and environmental benefits.

Paraphrase Generation is one of the most important and challenging tasks in the field of Natural Language Generation. The paraphrasing techniques help to identify or to extract/generate phrases/sentences conveying the similar meaning. The paraphrasing task can be bifurcated into two sub-tasks namely, Paraphrase Identification (PI) and Paraphrase Generation (PG). Most of the existing proposed state-of-the-art systems have the potential to solve only one problem at a time. This paper proposes a light-weight unified model that can simultaneously classify whether given pair of sentences are paraphrases of each other and the model can also generate multiple paraphrases given an input sentence. Paraphrase Generation module aims to generate fluent and semantically similar paraphrases and the Paraphrase Identification systemaims to classify whether sentences pair are paraphrases of each other or not. The proposed approach uses an amalgamation of data sampling or data variety with a granular fine-tuned Text-To-Text Transfer Transformer (T5) model. This paper proposes a unified approach which aims to solve the problems of Paraphrase Identification and generation by using carefully selected data-points and a fine-tuned T5 model. The highlight of this study is that the same light-weight model trained by keeping the objective of Paraphrase Generation can also be used for solving the Paraphrase Identification task. Hence, the proposed system is light-weight in terms of the model’s size along with the data used to train the model which facilitates the quick learning of the model without having to compromise with the results. The proposed system is then evaluated against the popular evaluation metrics like BLEU (BiLingual Evaluation Understudy):, ROUGE (Recall-Oriented Understudy for Gisting Evaluation), METEOR, WER (Word Error Rate), and GLEU (Google-BLEU) for Paraphrase Generation and classification metrics like accuracy, precision, recall and F1-score for Paraphrase Identification system. The proposed model achieves state-of-the-art results on both the tasks of Paraphrase Identification and paraphrase Generation.

Introduction: Pancasila was born as the ideology of the Indonesian nation, which reflects the values cultural values, ethics, morals, and the spirit of the nation. Pancasila was born as a form of national character, which reflects divinity, nationality, unity, togetherness, and justice. The purpose of this research is to know the practice of Pancasila values ​​in the life of the nation and the state. Especially, the implementation of the life of the younger generation in the 21st century today. Methods: This study is literature research where data is collected using keywords in the database. Literature source search carried out with the help of Boolean operators and using the PICOS format. The results of selecting articles, using PRISMA Flow Diagrams. The search results found 125 articles that match the research theme. After checking for duplication, 82 articles were excluded because of the similarity in the results of the discussion. In the end, there were 43 articles used as a literature source. Results: Based on the analysis of research findings, which are supported by literature sources, it shows that the current values ​​of Pancasila are worrying. This can be seen, where people's behavior has been contaminated by external cultures due to technological sophistication. At present, it can be said that the ethics and morals of society do not reflect the values ​​of Pancasila. Conclusion: In order to re-install the values ​​of Pancasila in people's lives, the participation of all parties is necessary. This is especially so, for today's younger generation. Therefore, it is necessary to develop a model for teaching Pancasila to be carried out by schools and colleges. So that later, it can produce a generation of ethics and morals who love the country.

This study investigates the impact of narrow-band terahertz pulses on the ferroelectric order parameter in Ba0.8Sr0.2TiO3 films on various substrates. The 375 nm thick BST film on an MgO (001) substrate exhibits enhanced THz-induced second harmonic generation when excited by THz pulses with a central frequency of 1.6 THz, due to the resonant excitation of the soft phonon mode. Conversely, the BST film on a Si (001) substrate shows no enhancement, due to its polycrystalline state. The 800 nm thick BST film on an MgO (111) substrate demonstrates maximum of second harmonic generation signal when excited by THz pulses at 1.8 THz, that is also very close to it`s soft mode frequency (1.9 THz). Notably, the frequency spectrum of the BST/MgO (111) film reveals peaks at both the fundamental and doubled frequencies, highlighting the quadratic dependence of SHG intensity on the THz pulse's electric field strength.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

The increasingly used approach of combining different simulation software in testing of automated driving systems (ADS) increases the need for potential and convenient software designs. Recently developed co-simulation platforms (CSP) provide the possibility to cover the high demand on testing kilometers for ADS by combining vehicle simulation software (VSS) with traffic flow simulation software (TFSS) environments. The emphasis on the demand of testing kilometers is not enough to choose a suitable CSP. The complexity level of the used vehicle, object, sensors and environment models is essential for valid and representative simulation results. Choosing a suitable CSP raises the question of how the test procedures should be defined and constructed and what the relevant test scenarios are. Parameters of the ADS, the environments, objects, sensors in VSS as well as traffic parameters in TFSS can be used to define and generate test scenarios. In order to generate a large number of scenarios in a systematic and automated way, suitable and appropriate software designs are required. In this paper we present a software design for CSP based on the Model-View-Controller (MVC) design pattern and implementation of a complex CSP for virtual testing of ADS. Based on this design, an implementation of a CSP is presented using the VSS from IPG Automotive called CarMaker and the TFSS from PTV Group called Vissim. The results have shown that the presented CSP design and the implementation of the co-simulation can be used to generate relevant scenarios for testing of ADS.

Large language models (LLMs) excel in providing natural language responses that sound authoritative, reflect knowledge of the context area, and can present from a range of varied perspectives. Agent Based Models and Simulation consist of simulated agents that interact within a simulated environment to explore societal, social, and ethical, among other, problems. Agents generate large volumes of data over time and discerning useful and relevant content is an onerous task. LLMs can help in communicating agents’ perspectives on key events by providing natural language narratives. However, these narratives need to be factual, transparent, and reproducible. To this end, we present a structured narrative prompt for sending queries to LLMs. Chi-square tests and Fisher’s Exact tests are applied to assess statistically significant difference in sentiment scores of the narrative messages between simulation generated narratives, ChatGPT-generated narratives, and real tweets. The narrative prompt structure effectively yields narratives with the desired components from ChatGPT. This structure is expected to be extensible across LLMs. In 14 out of 44 categories, ChatGPT generated narratives which has sentiment scores that were not discernibly different, in terms of statistical significance (alpha level of 0.05), from the sentiment expressed in real tweets. Three outcomes are provided: (1) a list of benefits and challenges for LLMs in narrative generation; (2) a structured prompt for requesting narratives of a LLM based on simulated agents’ information; and (3) an assessment of statistical significance in the sentiment prevalence of the generated narratives compared to real tweets. This indicates significant promise in the utilization of LLMs for helping to connect simulated agent’s experiences with real people.

As one of the world's most populous countries, Indonesia is struggling with the composition of its people, the majority of whom are unemployed productive-age individuals with low education levels. Another issue is the high poverty rate, which is followed by issues of gender inequality. The government cannot solve these social issues on its own. There is a need for community support to solve these problems through sustainable social entrepreneurship activities. Using the Theory of Planned Behavior and Outcome Expectation, this study will determine the factors that influence the interest of individuals known as the Z and Millennial generation, aged 18 to 34 years old, in becoming social entrepreneurs. This study applied a quantitative approach with a judgmental sampling technique to a sample of Generation Z and Millennials who have ever participated in social activities but have not yet started their own business. The study gathered 210 respondents, who were then analyzed using the PLS-SEM method with multiple group analysis generation-based comparison. According to the findings, the Millennial Generation's Attitude Toward Behavior, Subjective Norms, and Outcome Expectation all had a positive impact on Social Entrepreneurial Intention. Meanwhile, Subjective Norms had no effect on Social Entrepreneurial Intention in the Z Generation. Only attitude toward behavior, perceived behavioral control, and outcome expectation have a positive effect on the development of social entrepreneurial intentions. Furthermore, the findings of this study confirm that subjective norms influence attitude toward behavior and Perceived Behavioral Control in both Generation Z and millennials.

The paper investigates experimentally the influence of the Fused Filament Fabrication (FFF) pre-processing strategy on the tribological properties of parts made of PEI (polyetherimide), investigating the difference in the weight loss of the samples caused by abrasive wear before and after the test. The samples were tested for abrasive wear resistance on a tribometer constructed according to ASTM G65/16 (dry sand). Two types of specimen printing orientation along X-axis (lengthwise) and along Z-axis (heightwise) were tested in the study. Three types of path generation strategies were used for manufacturing "X" and "Z" specimens and totally 18 samples were made and tested. Path deposition strategy was carried out with path deposition width of 0.5mm and parallel paths in all slicing layers. In order to reduce the voids in volume, deposition path axes in subsequent layers were shifted by 0.25mm offset. Garnet abrasive Fe3Al2(SiO4)3 was used for this test. The analysis of the experimental data shows the relationship between the samples building direction (X, Z), applied deposition strategies (1X - 3X and 1Z - 3Z) on the resulting resistance to abrasive wear.Keywords: PEI, FFF, path generation strategy, abrasive wear

The sandwich generation caregivers provide simultaneous care for multiple generations. Caregiving is a dynamic process, and each generation has its unique set of needs. Moreover, studies have indicated a growing population within this group. However, despite extensive research efforts, the caregiving practices employed by the sandwich generation remain inadequately explained. Therefore, the objective of this study was to shed light on the caregiving practices offered by the sandwich generation. The grounded theory approach was selected as the conceptual framework for investigating the research objective. Purposive and snowball sampling methods were utilized to recruit 18 participants from the sandwich generation. The data collected through interviews and observations were analyzed using the 2015 version of Corbin and Strauss methodology. The findings revealed that sandwich generation caregivers are influenced by prominent personality traits, issues related to the elderly, and dependencies and interdependencies within the caregiving process. Sandwich caregivers employ a range of strategies influenced by intervening and background factors. Throughout this process, caregivers encounter both positive and negative consequences. Consequently, policymakers and planners should prioritize the establishment and expansion of support systems for caregiving.

Asphaltene is a component of crude oil that, if mishandled, may create substantial transportation and industrial concerns. It is a solid by nature, with a diverse set of molecular compositions. Furthermore, the oil industry has identified emulsion generation and clogging precipitate as key concerns. The emulsified water droplets in the process are just what give the raw oil its increased viscosity; hence, power is squandered to transport the oil around. The information has been separated into sections based on simulation, solubilization, agglomeration, precipitation, and evidence of model chemicals in the literature. We have included research that investigates the bulk rheology and interfacial rheology of asphaltene to describe its interfacial activity more clearly.

Introduction: Industrial revolution 4.0 in the current era of globalization plays an active role in the modern era in Indonesia. The influence of increasingly advanced technology affects the millennial generation as the nation's next generation to make Pancasila the basis of the State or the foundation of a State. In addition, the millennial generation has begun to shift the guidelines of life from Pancasila so that the appreciation of Pancasila values is starting to disappear along with the development of the times and in line with the progress of Science and Technology (IPTEK). If this continues, then the values of Pancasila will be replaced by a new ideology that will cause behavioural changes in society. Purpose: this study aims to provide the proper application to millennial life using Pancasila values, knowing the behaviour of the millennial generation towards the implementation of Pancasila values, and making Pancasila a way of life. Methods: the method used in this research is Literature Review and takes sources from journals published in 2019 to 2021 related to the Pancasila theme and the millennial generation. Results: the study results show that with the existence of Pancasila as the ideology and principle of the State, it is expected to strengthen the attitude and nature of the community in accepting things outside the norms that exist in Indonesia. In addition, the younger generation is expected to be able to apply Pancasila values along with the development of science and technology in the modern era and current globalization. The research question is how to make the millennial generation implement Pancasila in life in the contemporary period and what solutions can continue to instil Pancasila values ​​in the 4.0 industrial revolution. Recommendation: the conclusion drawn is that Pancasila can become a unifying tool for the nation if the current generation or millennial generation still desires to maintain its values ​​, even though they are in a modern era and many influences from its outside cultures. Limitation: the limitation of this research is not getting all the data directly from the source. The researcher recommends using primary data for the following study to ensure its truth and accuracy better because the researcher directly obtains it.

Pairs of potential and flow variables have long been established for interfacing object-oriented component models of physical systems. Recently, however, the use of triplets has been discovered for the purpose of robust modeling. New and powerful Modelica libraries have been developed such as the DLR ThermoFluid Stream library or the introduction of the Dialectic Mechanics library. Their use of triplets is entangled with a special modeling approach that uses Linear Implicit Equilibrium Dynamics. In this paper, we study the basic motivation of this approach, its benefits and drawbacks before we finally demonstrate how it beneficially impacts the generation of corresponding simulation code.

Character education is essential for the current millennial generation and must be applied in everyday life in the surrounding community. The character of the millennial generation is different from the previous generation, which requires us to pay more attention to character education which is starting to erode along with the times. The Millennial generation is a generation that in everyday life can never be separated from science and technology. In this digital era, the millennial generation has a social function of strength in technology. In this study, there are research questions that will be discussed in this article, namely the first regarding what problems occur in the millennial generation who occupy the digital era?. Second, what is the important role and influence of the digital era on character education for the millennial generation in Indonesia?. Writing this article uses a qualitative research method, namely a literature review study, where researchers use or look for references from journals or books. Samples of respondents were taken randomly from each region, and there were ten respondents. From this research, it is found that the millennial generation in the digital era chooses to use social media to access the latest news and information rather than reading print media that contains education. This article aims to find out the importance of character education for the millennial generation, which is starting to erode with the times in the digital era. Many people underestimate character education, especially for the current millennial generation. Therefore, we must implement educational programs at any level, especially in Indonesia, because the character shows the national identity. This article will discuss the vital role and influence of character education for millennials who live in the digital era to be aware of the importance of character education in citizenship.

Ruminal microorganisms play a pivotal role in cattle nutrition. The discovery of the main microbes responsible for enhancing the gain of weight in beef cattle might be used in therapeutic approaches to increase animal performance and cause less environmental damages. Here, we examined differences in bacterial and fungal composition of rumen samples of Braford heifers raised in a natural grassland from Pampa Biome in Brazil. We aimed to detect microbial patterns in the rumen that could be correlated with the gain of weight. 16S and ITS1 genes were amplified from ruminal samples and sequenced to identify the closest microbial relatives within the microbial communities. A predictive model based on microbes responsible for the gain of weight was build and further tested using the entire dataset. The model detected a set of microorganisms associated with animals in the high gain of weight group, including the bacterial taxa RFN20, Prevotella, Anaeroplasma and RF16 and the fungal taxa Aureobasidium, Cryptococcus, Sarocladium, Pleosporales and Tremellales. Most of these organisms have been correlated to the production of substances that improve the ruminal digestion process. These findings provide new insights about cattle nutrition and suggest the use of these microbes to improve beef cattle breeding.

After human genome sequencing and rapid changes in genome sequencing methods, we have entered in the era of rapidly accumulating genome-sequencing data. This has poses development of several types of methods for representing results of genome sequencing data. Circular genome visualizations tools are also critical in this area as they provide rapid interpretation and simple visualization of overall data. In the last 15 years, we have seen rapid changes in circular visualization tools after the development of the circos tool with 1–2 tools published per year. Herein we have summarized and revisited all these tools until the third quarter of 2018.

This paper aims to explore how climate change affects electricity generation (fossil-fueled power plants, hydroelectric stations, wind systems and photovoltaics) and energy demand in residential buildings in Greece for the period up to 2050. In both cases RCP scenarios results are considered in the appropriate spatial and temporal dimension. Energy supply technologies were examined through statistical regression models and/or mathematical equations correlating climatic parameters with energy productivity. With respect to energy demand, bottom-up models were developed that integrate behavioral and policy aspects. The analysis showed that climate change is expected to mainly affect electricity generation from hydro and thermal power plants, while the impacts on solar and wind energy are significantly lower. The range of impacts on hydro potential and electricity generation depends on the geographical location of the power plants and shows significant uncertainty due to the corresponding uncertainty in climate models estimates regarding precipitation and runoff changes while showing significant geographical variations. With respect to energy demand, climate change is expected to affect energy consumption, but the expected range of effects depends on both the implementation and the characteristics (deep vs. shallow renovation) of measures for upgrading the thermal performance of the building stock and the intensity of climate change.

“Pecorino” is a typical semi-hard cheese obtained with raw or heat-treated sheep milk using procedures to valorize the raw material's chemical and microbiological properties. In the present study, using a high throughput method of 16S rRNA gene sequencing, we assessed the evolution of the microbiome composition from milk to Pecorino cheese in artisanal processes using milk from Comisana and Lacaune sheep breeds. The comparative analysis of the bacterial com-munity composition revealed significant differences in the presence and abundance of specific taxa in the milk microbiome of the Comisana and Lacaune breeds. NGS analysis also revealed differences in the curd microbiome related to dairy farming practices, which have a relevant effect on the final structure of the Pecorino-cheese microbiome.

Introduction: The imbalance between technological development and ideological strengthening has resulted in the fading of the Pancasila ideological values of millennials. Technology that accompanies everyday life seems to be the main character in human life. Yet if humans themselves do not use technology wisely, technology can be a threat to both individuals and the life of the nation and state. If technology is increasingly out of control, threats to the Pancasila ideology are very likely to occur, such as in the G 30S PKI incident. Therefore, it is necessary to take action both from the government and the community as individuals to safeguard the development of technology to be used wisely. That way, we can prevent the threat to the Pancasila ideology together. Writing this article aims to analyze how the role and influence of the Pancasila ideology on the millennial generation in the 4.0 industrial revolution and to find solutions so that the values of Pancasila remain attached to the next generation of the Indonesian nation. Method: Writing This article uses a qualitative method by using literature reviews from the results of related research journals that have been published online through websites and other online media. Results: Thirteen journals and one book have met the criteria for the inclusion of a predetermined review. Research is based on the stigma of society regarding technological developments in the Industrial revolution 4.0. Therefore, the government is expected to be more severe in implementing human capital management. Conclusion: By procuring human capital management, it will be possible that Human Resources (HR) in Indonesia will be able to carry out the ideals of a golden Indonesian generation with Pancasila values inherent in the hearts of the people and the nation's future generations.

Plasma cell-free DNA (cfDNA) is frequently analyzed using liquid biopsy to investigate cancer markers. Accordingly, we hypothesized this concept could be applied to the field of exercise physiology. Here, we aimed to identify specific cfDNA (spcfDNA) sequences in the plasma of non-treated human participants using next generation sequencing (NGS) and to clearly define the dynamics regarding the amounts of spcfDNA-fragments upon extreme exercise, such as running a full marathon. NGS analysis was performed using cfDNA of pooled plasma collected from non-treated participants. We confirmed the TaqMan-qPCR assay had a high sensitivity and found the spcfDNA sequence abundance was 16,600-fold higher than a normal genomic region. We then used the TaqMan-qPCR assay to investigate the dynamics of the levels of spcfDNA-fragments upon running a full marathon. Quantities of the spcfDNA fragments were significantly increased post marathon. Furthermore, the amounts of spcfDNA fragments strongly correlated with the numbers of white blood cells and plasma myoglobin concentrations. These results suggest the spcfDNA fragments identified in this study were highly sensitive response markers to extreme physical stress. The findings of this study may provide new insights into exercise physiology and genome biology on the human.

In this study we announce the draft genome sequence of a newly identified Acinetobacter species cross-reacting with E. coli serotype 0157:H7. The advent of Next-Generation technology has paved to way to discover new species which could otherwise be misidentified using conventional cultural and serotyping methods. The whole genome sequence of this isolate will help to identify potential marker/s of intervention and further genomic analysis might also shed light onto the virulence properties of this newly identified Acinetobacter species which has been provided the new name of Acinetobacter maqsudiensis.

Background: Currently, Indonesia is entering an era that is all digital and uses technology in all fields of activity. The internet has a lot to do with their behavior or character. Millennials are the nation's next generation. The emergence of the digital era caused by globalization has made the millennial generation less appreciative and practicing the values ​​of Pancasila. In this case, character education is something that must be applied to the millennial generation. Purpose: This study aims to analyze the characteristics of the millennial generation, the role of character education in realizing the values ​​of Pancasila in the daily life of the millennial generation, how to cultivate an attitude of patriotism and nationalism towards the nation by practicing Pancasila, and provide motivation for the millennial generation to realize these values. Pancasila values. Methods: This study uses a literature review method. The search for journals was carried out using the google scholar database with the keywords “Character Education”, “millenial generation”, and “Pancasila”. The journals selected are journals from 2019 to 2020. Results: By applying character education to the millennial generation, it will make it easier for them to practice the values ​​of Pancasila. Pancasila should be the way of life of the millennial generation. Recommendation and limitation: As millennials, we must protect the country from values ​​that are contrary to Pancasila. Character education must be applied following the nature of the millennial generation itself. Of course, the applied character education must prioritize and be based on the values ​​of Pancasila as well.

The interest in renewable energy to replace fossil fuel is increasing as the problem caused by climate change become more severe. Small hydropower (SHP) is evaluated as a resource with high development value because of its high energy density compared to other renewable energy sources. SHP may be an attractive and sustainable power generation environmental perspective because of its potential to be found in small rivers and streams. The power generation potential could be estimated based on the discharge in the river basin. Since the river discharge depends on the climate conditions, the hydropower generation potential changes sensitively according to climate variability. Therefore, it is necessary to analyze the SHP potential in consideration of future climate change. In this study, the future prospect of SHP potential is simulated for the period of 2021 to 2100 considering the climate change in three hydropower plants of Deoksong, Hanseok, and Socheon stations, Korea. As the results, SHP potential for the near future (2021 to 2040) shows a tendency to be increased and the highest increase is 23.4% at the Deoksong SPH plant. Through the result of future prospect, we have shown that hydroelectric power generation capacity or SHP potential will be increased in the future. Therefore, we believe that it is necessary to revitalize the development of SHP in order to expand the use of renewable energy. Also, a methodology presented in this study could be used for the future prospect of the small hydropower potential.

SARS-CoV-2 is a novel betacoronavirus and the aetiological agent of the current COVID-19 outbreak that originated in Hubei Province, China. While polymerase chain reaction is the front-line tool for SARS-CoV-2 surveillance, application of amplification-free and culture-free methods for isolation of SARS-CoV-2 RNA, partnered with next-generation sequencing, would provide a useful tool for both surveillance and research of SARS-CoV-2. We here release into the public domain a set of bait capture hybridization probe sequences for enrichment of SARS-CoV-2 RNA from complex biological samples. These probe sequences have been designed using rigorous bioinformatics methods to provide sensitivity, accuracy, and minimal off-target hybridization. Probe design was based on existing, validated approaches for detecting antimicrobial resistance genes in complex samples and it is our hope that this SARS-CoV-2 bait capture platform, once validated by those with samples in hand, will be of aid in combating the current outbreak.

Given the imperative of security, sustainability of supply, strategic considerations, and energy independence, there is a widely acknowledged need to persist in utilizing coal as the primary fuel for electricity generation in power plants. However, in order to combat the rising levels of CO2 in the atmosphere, it is crucial to advance the development of carbon capture and storage (CCS) technologies that enable fossil fuel power plants to achieve zero emissions. These technologies play a pivotal role in capturing and effectively storing CO2, thus ensuring that coal-based power generation can continue while significantly reducing its environmental impact. By implementing CCS solutions, fossil fuel power plants can transition towards a more sustainable and environmentally friendly energy future.The utilization of chemical solvents for CO2 absorption, coupled with long-term storage, presents an intriguing and commercially viable technology for CO2 capture. However, the significant energy demands of the solvent regeneration process necessitate optimization, particularly in large-scale power plants. While the current cost of CO2 capture stands at approximately #55,000.00(Naira) per ton of CO2, the objective is to reduce this cost to below #25,000.00(Naira) per ton of CO2. This reduction in cost is essential to ensure the economic feasibility and widespread adoption of CO2 capture technologies in power generation.This research paper explores various approaches to address the energy demands associated with amine scrubbing integration in a commercial power plant. It provides a comprehensive analysis, both technically and economically, of the performance of these different approaches. While some of the proposed schemes may result in minor efficiency reductions, the key objective is to calculate the specific cost per ton of CO2 captured. The primary focus is on identifying the most suitable configuration to implement large-scale, cost-effective schemes that can serve as a foundation for CO2 capture demonstration projects. By determining the optimal configuration, this research aims to pave the way for the successful implementation of efficient and economically viable CO2 capture technologies in the power generation sector.

Metal halide perovskites (MHPs), in particular lead-based halide perovskites have earned a recognized fame in several fields for their outstanding optoelectronics properties including direct generation of free charge carriers, optimal ambipolar charge carrier transport properties, high absorption coefficient, point-defect tolerance, and compositional versatility. Nowadays, this class of materials represents a real and promising alternative of silica for the photovoltaic technologies. This worthy success led to a growing interest in the exploration of MHP materials in other hot research fields such as the solar-driven photocatalytic water splitting towards hydrogen production, CO2 reduction to CO and CH4, useful organic reactions such as organic synthesis (formation of C-C, C-N, and C-O bonds), and pollutants and dye degradation. Nevertheless, many of these perovskite materials showed air and moisture instability problems that considerably hinder their practical application for photocatalytic water splitting and photodegradation of CO2. Moreover, if the chemical instability is a problem that can be in part mitigated by the optimization of the lattice structure, the presence of lead represents a real problem for the practical application of these type of materials in commercial devices. To successfully overcome this problem, lead-free metal halide perovskites (LFMHPs) have gained increasing interest thanks to their promising optoelectronic properties, comparable to lead-based materials, and their eco-friendly nature. Among all the lead-free perovskite alternatives, this mini review will focus the attention on the bismuth-based perovskites and perovskite derivatives with specific focus on solar-driven photocatalysis application for H2 evolution.

Background: In the current era of globalization, the Indonesian government's problem today is the weakening of nationalism and patriotism among the millennial generation. The large number of foreign cultures that have entered Indonesia has caused a sense of nationalism and patriotism. In addition, Indonesia is also facing the problem of spreading the Covid-19 virus. During the pandemic, various policies set by the government received protests from some circles because they felt their freedom was restricted. Therefore, the awareness of millennial generation nationalism is needed, especially during the Covid-19 pandemic like today. This research aims to make millennials aware of nationalism sense, which mainly to prevent the spread of Covid-19. This research is used to answer the questions of what the problems that arise due to the waning of the spirit of nationalism during the pandemic are? and what efforts should be made to maintain the spirit of nationalism? Methods: This research is a qualitative study using the literature review method. The articles used are research published in 2019 to 2021 in Google Scholar, with keywords that match the topic of millennial generation nationalism in the Covid-19 pandemic. Results and Discussion: The results of the study found that the spirit of Indonesian nationalism during the Covid-19 pandemic was decreasing. The decline in the sense of nationalism is due to several government policies that impact the psychology of society and the Indonesian economy. As a result, society, particularly the millennial generation, must play a role in breaking the chain of the Covid-19 virus's propagation by following the government's health standards. Conclusion: The government and society need to work together to understand nationalism in the millennial generation, especially in dealing with problems caused by the Covid-19 pandemic. Based on this, various efforts need to be made to foster the spirit of nationalism and overcome the Covid-19 pandemic. So that later, it can produce a generation that upholds the value of nationalism in everyday life.

Three computer algorithms are presented. One reduces a network $\CALN$ to its interior, $\CALI$. Another counts all the triangles in the network, and the last randomly generates networks similar to $\CALN$ given just its interior $\CALI$. But these algorithms are not the usual numeric programs that manipulate a matrix representation of the network; they are set-based. Union and meet are essential binary operators; contained_in is the basic relational comparator. The interior $\CALI$ is shown to have desirable formal properties and to provide an effective way of revealing ``communities'' in social networks.

MicroRNAs (miRNAs) dysregulation contribute the cancer pathogenesis. However, the miRNA profile of canine oral melanoma (COM), one of the frequent malignant melanoma in dog is still unrevealed. The aim of this study is to reveal the miRNA profile in canine oral melanoma. MicroRNAs profile of oral tissues from normal healthy dogs and COM patients were compared by next-generation sequencing. Along with tumour suppressor microRNAs (miRNAs), we report 30 oncogenic miRNAs in COM. Expression of miRNAs were further confirmed by quantitative real-time PCR (qPCR). Pathway analysis showed that deregulated miRNAs impact on cancer and signalling pathways. Three oncogenic miRNAs targets (miR-450b, 301a, and 223) from human study also were down-regulated in COM and had significant negative co-relation with their respective miRNA. Furthermore, we found that miR-450b expression is higher in metastatic cells and regulated MMP9 expression through a PAX9-BMP4-MMP9 axis. In silico analysis indicated that miR-126, miR-20b, and miR-106a regulated the highest numbers of differentially expressed transcription factors in respect to human melanoma. Chromosomal enrichment analysis revealed the X chromosome was enriched with oncogenic miRNAs. We comprehensively analyzed the miRNA’s profile in COM which will be a useful resource for developing therapeutic interventions in both species.

This research aimed to determine salient factors affecting the decision to become a beginning organic farmer. New and beginning organic farmers have unique characteristics, showcasing their dedication to environmental justice and social justice at the expense of their own businesses. This research employed a multiple-case case study design. We conducted semi-structured interviews with 40 first-generation farmers who operate organic farms in Arkansas, Florida, or Georgia. We analyzed interview transcripts using the qualitative analysis approach of coding. Our results revealed the reasons that people with little practical knowledge start farms. They are inspired by those around them who succeed and encouraged by influential characters in the field who assure them they can do something they love and be profitable. This research showed that first-generation farmers find inspiration and develop values rooted in food justice. Our findings have implications for developing and implementing current and future programmatic activities that aim to enhance beginning farmer training and workforce development. Identifying sources of inspiration will help researchers and service providers target newer and beginning farmers to support a vibrant food system, including a burgeoning market opportunity, developing strong communities around food, and building grassroots solutions.

Sweet cucumber (Solanum muricatum) sect. Basarthrum, is a neglected horticultural crop native of the Andean region. It is naturally distributed very close to potatoes (Solanum sect. Petota) and tomatoes (Solanum sect. Lycopersicon), two groups of high economic importance. To date, molecular tools for this crop are still undetermined. We here obtained the first complete chloroplast (cp) genome of sweet cucumber and compared with seven Solanaceae species. Pair-end clean reads were obtained by PE 150 library and the Illumina HiSeq 2500 platform. The complete cp genome of S. muricatum had a 155,681 bp with typical quadripartite structure, containing a large single copy (LSC) region (86,182 bp) and a small single-copy (SSC) region (18,360 bp), separated by two inverted repeat (IR) regions (25,568 bp). The annotation of chloroplast genome predicted 88 protein-coding genes (CDS), 8 ribosomal RNA (rRNA) genes, 37 transfer RNA (tRNA) genes, and one pseudogene. A total of 48 perfect microsatellites were identified, divided in mononucleotide repeats (32), followed by tetranucleotide (6) and dinucleotides (5). SSRs with trinucleotides repeats (3), pentanucleotide (1) and hexanucleotide (1) repeats motifs in these genomes were identified in lower quantity. Most of these repeats were distributed in the noncoding regions. Whole chloroplast genome comparison with the other seven Solanaceae species revealed that the small and large single copy regions showed more divergence than inverted regions. Finally, phylogenetic analysis resolved that S. muricatum is a sister species to members of sections Petota + Lycopersicum + Etuberosum. This study reports for the first time the genome organization, gene content, and structural features of the cp genome of S. muricatum. Also, this study may provide the basis for evaluating genetic diversity within Solanum, and will be useful to examine the evolutionary processes in sweet cucumber landraces.

MCPH1, otherwise known as the microcephalin gene (*607117) and protein, is a basic regulator of chromosome condensation (BCRT-BRCA1 C-terminus). The Microcephalin protein is made up of three BCRT domains and conserved tandem repeats of interacting phospho-peptide. There is a strong connection between mutations of the MCPH1 and reduced brain growth. Specifically, individuals with such mutations have underdeveloped brains which means smaller size, varying levels of mental retardation, delayed speech and poor language skills, individuals with mild microcephaly and normal intelligence notwithstanding. In this case, a fetus with novel homozygous mutation of the MCPH1 gene ((c.348del)), whose parents were recessive heterozygous for (c.348del), displayed severe microcephaly at 22 weeks of gestation. Due to the effect on splice sites in introns, this mutation causes forming of dysfunctional proteins which lack crucial domains of the C-terminus. Our findings portray an association between the new MCPH1 mutation ((c.348del)) and the clinical features of autosomal recessive primary microcephaly (MCPH) contributing to a broader spectrum related to these pathologies.

Left ventricular noncompaction (LVNC) and hypertrophic cardiomyopathy (HCM) commonly occur as separate disorders with distinct clinical and pathoanatomical features. However, these cardiomyopathies may have a similar genetic origin with mutations encoding sarcomeric proteins. The described case demonstrates an example, in which phenotypic expression of both diseases occurs in the same patient.

This study explores the potential of data science software solutions like Customer Relationship Management Software (CRM) for increasing the revenue generation of businesses. We focused on those businesses in Accommodation and Food Service sector across the European Union (EU). The investigation is contextualized within the rising trend of data-driven decision making, examining the potential correlation between data science application and business revenue. Employing a comprehensive evaluation of Eurostat datasets from 2014 to 2021, we used both univariate and multivariate analyses, we assessed e-commerce sales data across countries, focusing on the usage of big data and CRM tools. Big data utilization showed a clear, positive relationship with enhanced e-commerce sales. However, CRM tools exhibited a dualistic impact: while their use in marketing showed no significant effect on sales, their application in non-marketing functions had a negative correlation. These findings underscore the potential role of CRM and data science solutions in enhancing business performance in the EU's Accommodation and Food Service industry.

Targeted next-generation sequencing (NGS) technology detects specific mutations that can provide treatment opportunities for colorectal cancer (CRC) patients. We included 145 CRC patients who underwent surgery. We analyzed the mutation frequencies of common actionable genes and their association with clinicopathological characteristics and oncologic outcomes using targeted NGS. Approximately 97.9% (142) of patients showed somatic mutations. Frequent mutations were observed in TP53 (70%), KRAS (49%), and APC (47%). TP53 mutations were significantly linked to higher overall stage (p=0.038) and lower disease-free survival (DFS) (p=0.039). ATM mutation was significantly associated with higher tumor stage (p=0.012) and shorter overall survival (OS) (p=0.041). Stage 3 and 4 patients with ATM mutations (p=0.023) had shorter OS, and FBXW7 mutation was significantly associated with shorter DFS (p=0.002). In multivariate Cox regression analysis, ATM mutation was an independent biomarker for poor prognosis of OS (p=0.022). TP53 and FBXW7 mutations are independent biomarkers for poor prognosis of DFS (p=0.042 and 0.030, respectively). A comprehensive analysis of the molecular markers for CRC can provide insights into the mechanisms underlying disease progression and help optimize a personalized therapy.

High frequency knowledge of the spatio-temporal distribution of the Downwelling Surface Shortwave Flux (DSSF) and its diffuse fraction (fd) at the surface is nowadays essential for understanding climate processes at the surface-atmosphere interface, plant photosynthesis and carbon cycle, and for the solar energy sector. The EUMETSAT Satellite Application Facility for Land Surface Analysis operationally delivers estimation of the MDSSFTD (Downwelling Surface Short-wave radiation Fluxes – Total and Diffuse fraction) product with an operational status since the year 2019. The method for the retrieval was presented in the companion paper [40]. The part 2 now focuses on the evaluation of the MDSSFTD algorithm and presents the comparison of the corresponding outputs, i.e. total DSSF and diffuse fraction (fd) components, against in-situ measurements acquired at four BSRN stations over a seven-month period. The validation is performed on an instantaneous basis. We show that the satellite estimates of DSSF and fd meet the target requirements defined by the user community for all-sky (clear and cloudy) conditions. For DSSF, the requirements are 20Wm^-2 for DSSF<200Wm^-2, and 10% for DSSF>=200Wm^-2. The MBE and rMBE compared to the ground measurements are 3.618Wm^-2 and 0.252%, respectively. For fd, the requirements are 0.1 for fd<0.5, and 20% for fd>=0.5. The MBE and rMBE compared to the ground measurements are -0.044 and -17.699%, respectively. The study also provides a separate analysis of the product performances for clear sky and cloudy sky conditions. The importance of representing the cloud-aerosol radiative coupling in the MDSSFTD method is discussed. Finally, it is concluded that the quality of the Aerosol Optical Depth (AOD) forecasts currently available is enough accurate to obtain reliable diffuse solar flux estimates. This quality of AOD forecasts was still a limitation a few years ago.

Computational Fluid Dynamics (CFD) simulations, based on Reynolds Averaged Navier Stokes (RANS) models, are a useful tool for a wide range of coastal and offshore applications, providing a high fidelity representation of the underlying hydrodynamic processes. Generating input waves in the CFD simulation is performed by a numerical wavemaker (NWM), with a variety of different NWM methods existing for this task. While NWMs, based on impulse source methods, have been widely applied for wave generation in depth averaged, shallow water models, they have not seen the same level of adoption in the more general RANS based CFD simulations, due to difficulties in relating the required impulse source function to the resulting free surface elevation for non-shallow water cases. This paper presents an implementation of an impulse source wavemaker, which is able to self-calibrate the impulse source function to produce a desired wave series in deep or shallow water at a specific point in time and space. Example applications are presented, for a numerical wave tank (NWT), based on the opensource CFD software OpenFOAM, for wave packets in deep and shallow water, highlighting the correct calibration of phase and amplitude. Also, the suitability for cases requiring very low reflection from NWT boundaries is demonstrated. Possible issues in the use of the method are discussed and guidance for good application is given.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

This research, which focuses on wave energy generating technology, suggests a brand-new oscillating float-type wave energy conversion system that is appropriate for the offshore wave environment. To accurately model the device, a three-dimensional viscous numerical pool is created based on STAR-CCM+. The array-type power generation device is numerically simulated using theoretical analysis and numerical simulation, and the wave energy power generation device is arranged as double floats in the front and rear rows, representing triangular array type and rectangular array type, respectively. The triangular array type is a superior layout and can make greater use of marine resources, according to this paper's analysis of the hydrodynamic and power generation impacts of the three array types. The findings are meant to serve as a guide for engineering practice.

Continuous glucose monitoring devices allow diabetes condition management. However, when limited data is available, one option is to increase their size by generating synthetic samples. From a homemade wearable prototype was created a real dataset with 18 instances and 53 attributes that capture characteristics of capillary and venous blood glucose, oxygen concentration, pulse rate, skin temperature, and 24 modules and 24 phases related to bio-impedance. The objective of this article is to generate synthetic datasets, and also it investigates the ideal features subset and optimal model for non-invasive diabetes prediction. Gaussian-Copulas (GC), conditional generative adversarial networks (CG), variational autoencoders, and Copula-GAN techniques' were used to generate five synthetic datasets. Experiments show that GC1 and GC2 datasets follow min/max boundaries and are not copies of the original data. Multilayer perceptron regressor outperformed (train and test) with 2.17, 2.51 in MAE; 9.29, 13.59 in MSE; 3.05, 3.69 in RMSE, and 0.95, 0.92 in R2 in GC1, and 2.64, 3.02 in MAE; 11.43, 15.11 in MSE; 3.38, 3.89 in RMSE, and 0.94, 0.92 in R2 in GC2 with eight features. Future work is necessary to explore autoencoder and generative architectures, datasets with diverse characteristics, and the effect of the number of features.

We attempted to understand the cervical cancer patient samples through Whole Exome Sequencing. We derived the variants from raw reads via our in-house benchmarked pipeline and validated the variants by IGV. This is the first cervical cancer exome data from the Indian cohort. Background: Cervical cancer (CC) is caused mainly by persistent infections of high-risk HPV, reduced parity, and factors like a decrease in average socioeconomic levels. We keep this because no cervical cancer exome data is available from the Indian cohort. Methods: The CC patient clinical samples were initially subjected to preparation using Qiagen DNA extraction, quantified, and the library preparation using the Agilent target enrichment system. Further, exome capture by Illumina platform (100X), quality check, alignment, and variant calling followed by the downstream analysis and finally visualized by IGV. Results: We observed a large number of SNVs or mutations from an Indian perspective, such as KMT2C, OR4M1, PDPR2P, EPHB1, FAS, OPCML, MGST1, C1QTNF9, HS6ST3, OR4K2, PRPSAP2, KCNJ12, FIGNL1, SFXN1, BAGE2, ARVCF, NAMPT variants of significance, unknown significance and possibly significant are reported. Conclusion: For the first time, KMT2C is observed as a novel potent mutation and pathogenic, showing the variant position at (7:152265091, T>A, SNV 62478356) from the Indian context in CC. Further, we visualized and validated the mutations using the Integrative Genomic Viewer (IGV) browser. Finally, we discuss the inherent challenges through KMT2C mutations.

Adhesion systems are very important in robots for infrastructure inspection (especially in vertical walls). They present the challenge of optimizing the ratio vacuum/power consumption in battery-powered robots. In this paper a CFD (Computer Fluid Dynamics) modelling and optimization process of a robot adhesion system is carried out to determine the best performing configuration in terms of vacuum and power consumption. Analytical and numerical models were developed to predict the behaviour of the system for different configurations. The models were validated, using test rig measurements, by calibrating an arbitrary defined inlet height that simulates the leakage flow. Then, different geometric parameters were varied to determine the best performing configuration based on the vacuum/power consumption ratio value. The model presented in the paper was capable of predicting the behaviour of the system for different configurations, with a margin of error of 15% for the vacuum prediction and a 25% for the motor power calculation. Finally, the model was used to optimize parameters of the system, like the number of blades of the impeller. The adhesion system was conceived for the modular autonomous climbing legged robot ROMERIN.

We review recent work on narrowband orthogonally polarized optical RF single sideband generators as well as dual-channel equalization, both based on high-Q integrated ring resonators. The devices operate in the optical telecommunications C-band and enable RF operation over a range of either fixed or thermally tuneable frequencies. They operate via TE/TM mode birefringence in the resonator. We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization for both the fixed and tunable devices.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

It is currently unknown whether thrombin generation is associated with venous thromboembolism (VTE) recurrence, major bleeding, and mortality in the elderly. Therefore, our aim was to prospectively study the association between thrombin generation and VTE recurrence, major bleeding and mortality in elderly patients with acute VTE. Consecutive patients aged ≥65years with acute VTE were followed for 2 years starting from 1 year after the index VTE. Primary outcomes were VTE recurrence, major bleeding and mortality. Thrombin generation was assessed in 565 patients 1 year after the index VTE. At this time, 59% of patients were still anticoagulated. Thrombin generation was discriminatory for VTE recurrence, but not for major bleeding and mortality in non-anticoagulated patients. Moreover, peak ratio (adjusted subhazard ratio 4.09, 95% CI, 1.12-14.92) and normalized peak ratio (adjusted subhazard ratio 2.18, 95% CI, 1.28-3.73) in presence/absence of thrombomodulin were associated with VTE recurrence, but not with major bleeding and mortality after adjustment for potential confounding factors. In elderly patients, thrombin generation was associated with VTE recurrence, but not with major bleeding and/or mortality. Therefore, our study suggests the potential usefulness of thrombin generation measurement after anticoagulation completion for VTE to help identifying among elderly patients those at higher risk of VTE recurrence.

This survey proposed an evaluation model to analyze and examine different approaches to generativity. In addition to problem domain concepts, the following concepts were used to define this model: Complexity and complexity management, and Systematics view to achieve unified and integrated insight into disparate evaluation criteria. The research's approach to the said concepts is first introduced. Then, the evaluation model is presented.

The Convective Rainfall Rate from Cloud Physical Properties (CRPh) for Meteosat Second Generation Satellites is a day-only precipitation algorithm developed at the Spanish Meteorological Agency (AEMET) for EUMETSAT’ Satellite Application Facility in support to Nowcasting and Very Short Range Forecasting (NWC SAF). It is therefore mainly intended to provide input for monitoring and near-real-time forecasts for the next few hours. This paper critically discusses the theoretical basis of the algorithm with special emphasis in the empirical values and assumptions in the microphysics of precipitation and compares the performances of the CRPh with its antecessor, the Convective Rainfall Rate algorithm (CRR), using an object-based method. The analyses show that AEMET’s CRPh is physically consistent and that outperforms the CRR. The applicability of the algorithm for nowcasting and the challenges to evolve the product to an all-day algorithm are also presented.

An understanding of the cultural conditions that determine the factors affecting nurses’ intention to leave is important for countries suffering from nurse shortage. Aim: to examine factors influencing intention to leave among female hospital nurses in a large Japanese sample, classified into four generations by age considering economic conditions. Methods: a cross-sectional survey with convenience sampling was conducted. Anonymous self-administered questionnaires were distributed to all nurses in 30 hospitals. To assess intention to leave, basic attributes, life conditions, work characteristics, and factors of psychosocial work environment were addressed. After classifying data into four generations based on age cohorts, we conducted multivariate logistic regression analysis using the completed data (N = 5,074, mean age = 36.24). Results: regardless of generational characteristics influenced by economic conditions, effort and monetary reward were generation-common factors. Over-commitment, social support, and the presence of a role model were generation-common factors in three generations. While having children increased intention to leave in the generation born 1965–1979, having family members in need of caregiving other than children decreased the risk in the generation born in the 1980s. Conclusion: generational countermeasures considering factors of psychosocial work environment and life conditions are needed to avert female nurse turnover.

This review delves into the critical role of automation and sensor technologies in optimizing parameters for thermal treatments within electricity power generation. The demand for efficient and sustainable power generation has led to a significant reliance on thermal treatments in power plants. However, ensuring precise control over these treatments remains challenging, necessitating the integration of advanced automation and sensor systems. This paper evaluates the pivotal aspects of automation, emphasizing its capacity to streamline operations, enhance safety, and optimize energy efficiency in thermal treatment processes. Additionally, it highlights the indispensable role of sensors in monitoring and regulating crucial parameters such as temperature, pressure, and flow rates. These sensors enable real-time data acquisition, facilitating immediate adjustments to maintain optimal operating conditions and prevent system failures. It explores the recent technological advancements, including machine learning algorithms and IoT integration, which have revolutionized automation and sensor capabilities in thermal treatment control. Incorporating these innovations has significantly improved the precision and adaptability of control systems, resulting in heightened performance and reduced environmental impact. This review underscores the imperative nature of automation and sensor technologies in thermal treatments for electricity power generation, emphasizing their pivotal role in enhancing operational efficiency, ensuring reliability, and advancing sustainability in power generation processes.