The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

This study refers to the optimization of a Selective Solar Absorber to improve the Sun-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal collectors. Efficiency has been evaluated by using analytical formula and a numerical thermal model. Both results have been experimentally validated using a commercial absorber in a custom experimental set-up. The optimization procedure aimed at obtaining Selective Solar Absorber is presented and discussed in the case of a metal dielectric multilayer based on Cr2O3 and Ti. The importance of adopting a real spectral emissivity curve to estimate high thermal efficiency at high temperatures in selective solar absorber is outlined. Optimized absorber multilayers can be 8% more efficient than the commercial alternative at 250 °C operating temperatures and up to 27% more efficient at 300 °C. Once the multilayer has been optimized the choice of a very low emissivity substrate such as copper allows to further improve efficiency and to reach stagnation temperature higher than 400 °C without Sun concentration.

This paper proposes the configuration of an Organic Rankine Cycle (ORC) coupled to a solar domestic hot water system (SDHWS), with the purpose of analyzing the cogeneration capacity of the system. A simulation of the SDHWS was conducted at different temperatures, observing its performance to determine the amounts of useable heat generated by the solar collector; thus, from an energy balance, the amount of heat that may be used by the ORC could be determined. The working fluid that would be suitable for the temperatures and pressures given in the system were selected. The best fluid for the given conditions of superheated vapor at 120 °C and 604 kPa and a condensation temperature of 60 °C and 115 kPa was acetone. The main parameters for the expander thermodynamic design that may be used in such ORC were obtained with the possibility of generating 443 kWh of annual electric energy, with 6.65 % global efficiency of solar to electric power, or an overall efficiency of the cogeneration system of 56.35 % with a solar collector of 2.84 m².

Among solar thermal collectors, the evacuated flat panel is emerging as a reference technology for operation at higher temperatures of up to 200 °C with an increased annual energy production owing to both direct and diffuse light capture. Accurate measurements of the optical properties of the selective absorbers used in such devices are key for a reliable estimation of the overall performance. These optical properties must be measured under high vacuum at high temperatures, conditions under which the panels are meant to operate. In this study, we accurately measured these properties using a calorimetric technique. The measurement procedure is based on a power balance equation for a flat sample suspended in a high-vacuum chamber with minimal thermal losses and is well adapted for this class of devices. Calorimetric measurements obtained under Sun and LED light revealed excellent reproducibility and good agreement with those obtained using traditional optical analysis at low temperatures in air. When extended up to the absorber stagnation temperature, which often exceeds 300 °C, the calorimetric measurements started to deviate from the optical measurements, indicating the importance of measuring under the operating conditions.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.