Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Wireless sensor networks (WSN) are widely used in various fields such as military, industrial and transportation for real-time monitoring, sensing and data collection of different environments or objects. However, the development of WSN is hindered by several limitations, including energy, storage space, computing power and data transmission rate. Among these, the availability of power energy plays a crucial role as it directly determines the lifespan of WSN. To extend the life cycle of WSN, two key approaches are power supply improvement and energy conservation. Therefor, we proposed an energy harvesting system and a low energy consumption mechanism for WSN. Firstly, we delved into the energy harvesting technology of WSN, explored the utilization of solar energy and mechanical vibration energy to ensure a continuous and dependable power supply to the sensor nodes, and analyzed the voltage output characteristics of bistable piezoelectric cantilever. Secondly, we proposed a neighbor discovery mechanism that utilizes a separation beacon, is based on reply to ACK, and can facilitate the identification of neighboring nodes. This mechanism operates at a certain duty cycle ratio, significantly reduces idle listening time and results in substantial energy savings. In comparison to the Disco and U-connect protocols, our proposed mechanism achieves a remarkable reduction of 66.67% and 75% in the worst discovery delay, respectively. Furthermore, we introduced a data fusion mechanism based on integer wavelet transform. This mechanism effectively eliminates data redundancy caused by spatio-temporal correlation, results in a data compression rate of 5.42. Additionally, it significantly reduces energy consumption associated with data transmission by the nodes.

Water covers a greater part of the earth's surface. Even though we know very little about the underwater world as most parts of it remain unexplored. Oceans including other water bodies hold huge natural resources and also the aquatic lives. These are mostly unexplored and very few of those are known due to unsuited and hazardous environments for the human to explore. This vast underwater world can be monitored remotely from a distant location with much ease and less risk. To monitor water-bodies remotely in real-time, sensor networking has been playing a great role. It is needed to deploy a wireless sensor network over the volume which we want to surveil. For vast water bodies like oceans, rivers and large lakes, data is collected from the different heights of the water level which is sent to the surface sink. Unlike terrestrial communication, radio waves and other conventional mediums can't serve the purpose of underwater communication as they pose high attenuation and very reduced transmission range. Rather an acoustic medium can transmit data more efficiently and reliably in comparison to other mediums. To transmit data reliably from the bottom of the sea to the sinks at the surface, multi-hop communication is needed which must involve a certain scheme. For seabed to surface sink communication, leading researchers have proposed different routing protocols. The goal of these routing protocols is to make underwater communication more reliable, energy-efficient and delay efficient thus to improve the performance of the overall communication. This paper surveys the advancement and applications of the routing protocols which eventually helps in finding the most efficient routing protocol for the Underwater Wireless Sensor Network (UWSN).

Wireless energy harvesting (EH) communication has long been considered a sustainable networking solution. However, it has been limited in efficiency, which has been a major obstacle. Recently, strategies such as energy relaying and borrowing have been explored to overcome these difficulties and provide long-range wireless sensor connectivity. In this article, we examine the reliability of the wireless-powered communication network by maximizing the net bit rate. To accomplish our goal, we focus on enhancing the performance of hybrid access points and information sources by optimizing their transmit power. Additionally, we aim to maximize the use of harvested energy by energy-harvesting relays for both information transmission and energy relaying. However, this optimization problem is complex as it involves non-convex variables and requires combinatorial relay selection indicators optimization for decode and forward (DF) relaying. To simplify this problem, we utilize the Markov decision process and deep reinforcement learning framework based on the deep deterministic policy gradient algorithm. This approach enables us to tackle this non-tractable problem, which conventional convex optimisation techniques would be difficult to solve in complex problem environments. The proposed algorithm significantly improves the end-to-end net bit rate of the smart energy borrowing and relaying EH system by 13.22%,27.57%, and 14.12% compared to the benchmark algorithm based on borrowing energy with an adaptive reward for Quadrature Phase Shift Keying, 8-PSK, and 16-Quadrature amplitude modulation schemes, respectively.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

With the widespread use of electric machines there is a growing need to extract information from the machines to optimize their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of an squirrel cage induction motor rotor physical variables. The system comprises: circuit to acquire desirable rotor variable(s) value(s) and send it to the computer; a rectifier and power storage circuit that besides converting an alternating current in continuous also store energy for a certain amount of time to wait the motor engine shutdown; and magnetic generator that harvest energy from rotating field to power the circuits mentioned above. The embedded system is set on the rotor, making it difficult to power the system because it is rotating, problem solved with the construction of the magnetic generator eliminating the need of using batteries or collector rings and send data to the computer using a wireless NRF24L01 module. For the proposed system validation a temperature sensor (DS18b20) was used, variable known as the most important when identifying the need for maintenance and control systems. Tests were made getting satisfactory results proving the viability of using sensors on the rotor.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

The sensor nodes have limited computation, sensing, communication capabilities and generally operated by batteries in a harsh atmosphere with non-replenish able power sources. These limitations force the sensor network subject to failure because most of the energy is spent on sensing, computing and data transmission. This paper introduces an Energy Efficient Clustering and Shortest-Path Routing Protocol (EECSRP) to assist Wireless Sensor Networks (WSNs) by (a) extending the lifespan of the network (b) effectively using the battery power (c) decreasing the network overhead and (d) ensuring a high packet transmission ratio with minimal delay. The delay time-based Cluster Head (CH) is elected based on the node degree, residual energy and Received Signal Strength (RSS) to accomplish the goal. Additionally, the RSS-based network partitioning is implemented to evaluate the gradient based on demand routing between source (sensing node) and destination (BS). Whenever the current CH residual energy goes under the threshold level, the proposed protocol performs the clustering process, reducing the exchange of control packets. However, the BS periodically gathers the data from every single CH which helps to reduce the collision and Medium Access Control (MAC) layer conflict. From the simulation results, it is the evident that the proposed protocol performance in terms of average end-to-end latency, packet delivery ratio, average energy consumption and control overhead is better than the well-known current protocols.

This work focuses on the research area of energy generation and harvesting for its transformation into electrical energy with the primary use of energy independent sensor systems in the power range P=10-10000W. These systems are applied in sensing quantities in the transport sector (bridge structures, transport infrastructure, and the others ). The proposed theoretical harvester models describing the transformation of motion energy into electrical energy, also provides theoretical and experimental models. Results obtained in the design and construction of a robust motion generator with primarily linear geometry system technology are presented. The expected output electrical power of the harvester is variable and is designed based on the linear motion generated by the engine- compressed air, small fuel system, etc. The fundamental design of the generator core has been continuously numerically modeled and an experimental setup has been developed to analyze specific parts and variations in order to validate the concept and achieve the most suitable parameters with the selected construction materials. A scaled down version of the model principle was tested in experiments and then the parameters and results were compared with the predicted theoretical analyses.

A run-of-the-mill remote sensor arrange comprises numerous vitality compelled sensor hubs that are arbitrarily sent is the sensor field. Vitality is one of the most significant parts of planning an information dispersal convention for applications, for example, war zone checking, living space observing, and so on. We present EGDD, an Energy-effective Grid-based Data Dissemination plot for arbitrarily conveyed remote sensor systems. The proposed conspire is vitality effective for dealing with both sink and source portability. EGDD depends on a virtual framework-based foundation for information scattering from various versatile sources to different portable sinks. The virtual lattice of square size is built by the main source showing up in the sensor field dependent on the remaining vitality of the sensor hubs. Moreover, we proposed an askew sending calculation for inquiry and information sending which guarantees that just a single spread hub advances the question and information at once. In EGDD, substitute scattering hubs are chosen ahead of time during the lattice development procedure and the least limit vitality level is characterized for spread hubs. When the vitality of a dispersal hub arrives at the base edge esteem, it is supplanted by another spread hub. The reenactment results show that the proposed EGDD conspire is more vitality proficient when contrasted with other information scattering conventions.

The reliability of Underwater Wireless Sensor Networks (UWSNs) is measured in terms of energy consumption (EC), end-to-end delay(E2E) and packet delivery ratio (PDR). The adverse effects of channel may cause data loss. Reducing delay up to possible extend improves the reliability of the network, also increasing the number of nodes in a particular network increase reliability. Besides, increasing the number of nodes improve reliability but also increase power consumption. In order to overcome these shortcomings, the two routing protocols are proposed in this paper, namely Delay and Reliability Aware Routing (DRAR) protocol and Cooperative Delay and Reliability Aware Routing (Co-DRAR) protocol for UWSNs. In DRAR protocol, network is divided into two equal regions where two sink nodes(SNs) are positioned at upper region of the network and two SNs are placed at the mid region of the network. The protocol choose the relay node based on residual energy (RE), distance and Bit Error Rate (BER). These parameters protect the data packets from corruption and also provide stable path (where nodes remain active for longer period and do not die quickly). The protocol uses single link and may get worse sometimes while changing channel circumstances. To address this problem, cooperative routing scheme is added to DRAR protocol in order to developed its enhanced version known as Co-DRAR protocol. The protocol works by allowing the destination to receive multiple copies of data packets in order to decide the quality of packets. The proposed protocols DRAR and Co-DRAR perform routing irrespective to geographical position of sensors nodes conversely to the some of conventional routing protocols that's way our propose protocol better perform than the well-known protocol i.e. Depth base routing (DBR) in terms of EC, E2E, PDR, dead nodes, packet drop ratio and number of alive nodes (ANs).

Load balancing, energy efficiency and fault tolerance are among the most important data dissemination issues in Wireless Sensor Networks (WSNs). In order to successfully cope with the mentioned issues, two main approaches (namely, Data-centric Storage and Distributed Data Storage) have been proposed in the literature. Both approaches suffer from data loss due to memory and/or energy depletion in the storage nodes. Even though several techniques have been proposed so far to overcome the mentioned problems, the proposed solutions typically focus on one issue at a time. In this paper, we integrate the Data-centric Storage (DCS) features into Distributed Data Storage (DDS) mechanisms and present a novel approach, denoted as Collaborative Memory and Energy Management (CoMEM), to overcome both problems and bring memory and energy efficiency to the data loss mechanism of WSNs. We also propose analytical and simulation frameworks for performance evaluation. Our results show that the proposed method outperforms existing approaches in various WSN scenarios.

In the past few years, the possibility to transfer power wirelessly has experienced growing interest from the research community. Since the wireless channel is subject to a large number of random phenomena, a crucial aspect is the statistical characterization of the energy that can be harvested by a given device. For this characterization to be reliable, a powerful model of the propagation channel is necessary. The recently proposed Generalized-K model has proven to be very useful, as it encompasses the effects of path-loss, shadowing and fast fading for a broad set of wireless scenarios, and it is analytically tractable. Accordingly, the purpose of this paper is to characterize, from a statistical point of view, the energy harvested by a static device from an unmodulated carrier signal generated by a dedicated source, assuming that the wireless channel obeys the Generalized-K propagation model. Specifically, using simulation-validated analytical methods, this paper provides exact closed-form expressions for the average and variance of the energy harvested over an arbitrary time period. The derived formulation can be used to determine a power transfer plan that allows multiple or even massive numbers of low-power devices to operate continuously, as expected from future network scenarios such as IoT or 5G/6G.

Wireless sensor networks are attractive largely because they need no wired infrastructure. But precisely this feature makes them energy constrained. Recent studies find that sensing behaviors that are otherwise deemed efficient consume comparable energy with communication. The duty cycle scheduling is perceived as contributing to achieving energy efficiency of sensing. Because of different research assumptions and objectives, various scheduling schemes have various emphases. This paper designed an adaptive sensing scheduling strategy. The objective function of the scheduling strategy includes minimizing average energy expenditure and maximizing sensing coverage (reducing event miss-rate), and it requires relatively loose assumptions. We determine the functional relationship between the variables of the objective function and the step-size parameters of the proposed strategy through the numerical fitting. We found that the objective function aggregated by the fitting functions is a bivariate multi-peak function that favors the Fibonacci tree optimization algorithm. Once the optimization of parameters is done, the strategy can be easily deployed and behaves consistently in the coming hours. We name the proposed strategy as “FTOS”. The experimental results show that the Fibonacci tree optimization algorithm gets a better optimistic effect than the comprehensive learning particle swarm optimization (CLPSO) algorithm and differential evolution (DE) algorithm. The FTOS strategy is superior to the fixed time scheduling strategy in achieving the scheduling objectives. It also outperforms other strategies with the same scheduling objectives such as LDAS, BS, DSS and PECAS.

Wireless Sensor Networks (WSNs) continue to provide essential services for various applications such as surveillance, data gathering, and data transmission from the hazardous environments to safer destinations. This has been enhanced by the energy-efficient routing protocols that are mostly designed for such purposes. Gateway-based Energy-Aware Multi-hop Routing protocol (MGEAR) is one of the homogenous routing schemes that was recently designed to more efficiently reduce the energy consumption of distant nodes. However, it has been found that the protocol has a high energy consumption rate, lower stability period, less data transmission to the Base station (BS). In this paper, an enhanced Heterogeneous Gateway-based Energy-Aware multi-hop routing protocol ( HMGEAR) is proposed. The proposed routing scheme is based on the introduction of heterogeneous nodes in the existing scheme, selection of the head based on the residual energy, introduction of multi-hop communication strategy in all the regions of the network, and implementation of energy hole elimination technique. Results show that the proposed routing scheme outperforms two existing ones.

Although many devices have recently been proposed for pressure regulation and energy harvesting in water distribution and transport networks, very few applications are still documented in the scientific literature. A new in-line Banki turbine with positive outflow pressure and a mobile regulating flap, named PRS, was installed and tested in a real water transport network for pressure and discharge regulation. The PRS turbine was directly connected to a 55 kW asynchronous generator with variable rotational velocity, coupled to an inverter. The start-up tests showed how automatic adjustment of the flap position and the impeller velocity variation are able to change the characteristic curve of the PRS according to the flow delivered by the water manager or to the pressure set-point assigned downstream or upstream of the system, still keeping good efficiency values in hydropower production.

Underwater wireless sensor networks (UWSN) have recently been proposed as a way to monitor and explore the water depths' environments. Efficiently delivering the data is still a challenging problem in these networks because of the weaknesses in the acoustic transmission. To tackle such a problem, we propose a novel algorithm provides controlling mechanisms for critical long-term data forwarding underwater sensor networks, called Hop by Hop Power-Efficient Routing Protocol (Hⁿ-PERP). The proposed Hⁿ-PERP is a centralized full-control model that enhances the network's throughput and energy efficiency by a set of solutions depend on power monitoring in UWSN nodes. In particular, the model provides a guaranteed mechanism for scheduling and processing data transmission based on number of nodes, hops between the nodes, energy level and congestion within each node to minimize energy levels or power consumption by avoiding disconnected probability for any node, which in turn maximizing the network lifetime. Simulation results show that our proposed model is consistent with energy level and congestion, and is more accurate for enabling routing and data transmission. Therefore, the data packet delivery ratio and overall throughput also achieves robust scenarios of very sparse or/and weak networks, to keep on Performance stability in UWSN via adjusting hop-by-hop delay and energy consumption during packages delivery.

Abstract: Wireless body area networks (WBANs) have strong potential in the field of health monitoring. However, the energy consumption required for accurate monitoring limits the time between battery charges of the wearable sensors, which is a key performance factor (and can be critical in the case of implantable devices). In this paper, we study the inherent trade-off between the power consumption of the sensors and the probability of misclassifying a patient’s health state. We formulate this trade-off as a dynamic problem, in which at each step we can choose to activate a subset of sensors that provide noisy measurements of the patient’s health state. We assume that the (unknown) health state follows a Markov chain, so our problem is formulated as a partially observable Markov decision problem (POMDP). We show that all the past measurements can be summarized as a belief state on the true health state of the patient, which allows tackling the POMDP problem as an MDP on the belief state. We then empirically study the performance of a greedy one-step look-ahead policy compared to the optimal policy obtained by solving the dynamic program. For that purpose, we use an open-source Continuous Glucose Monitoring (CGM) data set of 232 patients over six months and extract the transition matrix and sensor accuracies from the data. We find that the greedy policy saves ~50% of the energy costs while reducing the misclassification costs by less than 2% compared to the most accurate policy possible that always activates all sensors. Our sensitivity analysis reveals that the greedy policy remains nearly optimal across different cost parameters and a varying number of sensors. The results also have practical importance, because while the optimal policy is too complicated, a greedy one-step look-ahead policy can be easily implemented in WBAN systems.

Sensor networks, as a special subtype of wireless networks, consist of sets of wirelessly connected sensor nodes often placed in hard-to-reach environments. Therefore, it is expected that sensor nodes will not be powered from the power grid. Instead, sensor nodes have their own power sources, the replacement of which is often impractical and requires additional costs, so it is necessary to ensure minimum energy consumption. For that reason, the energy efficiency of wireless sensor networks used for monitoring environmental parameters is essential, especially in remote networking scenarios. In this paper, an overview of the latest research progress on wireless sensor networks based on LoRa was provided. Furthermore, the analyses of the energy consumption of sensor nodes used in agriculture to observe environmental parameters were carried out. Optimization methods of energy consumption, in terms of choosing the appropriate data collection processes, as well as the settings of wireless network radio parameters were suggested. In the conducted analyses, special emphasis was placed on choosing the optimal package size. In this paper, it was proven that the adjustment of the transmission speed to the actual size of the packet is important for better energy efficiency of communication.

A single tree topology is a commonly employed topology for wireless sensor networks (WSN) to connect sensors to one or more remote gateways. However, its many-to-one traffic routing pattern imposes heavy burden on downstream nodes, as the same routes are repeatedly used for packet transfer, from one or more upstream branches. The challenge is how to choose the most optimal routing paths that minimizes energy consumption across the entire network. This paper proposes a proactive energy awareness-based many-to-one traffic routing scheme to alleviate the above said problem referred to as Energy Balance-Based Energy Hole Alleviation in tree topology (EBEHA-T). This protocol combines updated status of variations in energy consumption pattern around sink-hole zones and distribution of joint nodes among the trees. With this approach, EBEHA-T proactively prevents sink-hole formation instead of just a reactive response after they have occurred. Performance evaluation of EBEHA-T against benchmark method RaSMaLai shows increased energy saving across the entire network and a marked improvement in energy consumption balance in energy-hole zones. This precludes energy hole formation and the consequent network partitioning, leading to improved network lifetime beyond that of the RasMaLai. OMNET++ network simulation software has been used for the evaluation.

In wireless sensor networks, there is no a central controller to enforce cooperation between nodes. Therefore, nodes may generate selfish behavior to conserve their energy resources. In this paper, we address the problems of transmission power minimization and energy balance in wireless sensor networks using a topology control algorithm. We considered the energy efficiency and energy balance of the nodes, and an improved optimization-integrated utility function is designed by introducing the Theil index. Based on this, a topological control game model of energy balance is established, and it is proved that the topological game model is an ordinal potential game with Pareto optimality. Additionally, an energy-balanced topology control game algorithm (EBTG) is proposed to construct topologies. The simulation and comparison show that, compared with other topological control algorithms based on game theory, the EBTG algorithm can improve energy balance and energy efficiency while reducing the transmitting power of nodes, thus prolonging the network lifetime.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

To facilitate wireless communication, ocean exploration, and various environmental and research applications, the underwater Internet of Things has been developed with an infrastructure of acoustic sensor networks. There has been a significant increase in failures and a decrease in the efficiency of the network due to the fluid and challenging underwater environment. Consequently, achieving quality of service (QoS) in underwater networks remains a research area. Supporting QoS in underwater sensor networks is challenging due to resource limitations such as processing power, memory, bandwidth, and power sources. The purpose of this study was to examine the service quality requirements as well as protocols that have been implemented in recent years. Finally, based on quality criteria, we have presented a routing solution based on fuzzy logic, which is more efficient than other recent methods regarding energy consumption rate, JFI, efficiency, and reliability.

The radio operation in wireless sensor networks (WSN) in the Internet of Things (IoT) applications are the most common source for power consumption. However, recognizing and controlling the factors affecting radio operation can be valuable for managing the node power consumption. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS used in WakeUp mode, which is a clear channel assessment (CCA) to check radio status periodically. The time spent to check the radio is of utmost importance for monitoring power consumption. It can lead to false WakeUp or idle listening in Radio Duty-Cycles and ContikiMAC. This paper presents a detailed analysis of radio WakeUp time factors of ContikiMAC. Then, we propose lightweight CCA (LW-CCA) as an extension to ContikiMAC to reduce the percentage of Radio Duty-Cycles in false WakeUps and idle listenings by using dynamic received signal strength indicators (RSSI) status check time. The simulation results in the Cooja simulator show that LW-CCA reduces about 8% energy consumption in nodes while maintaining up to 99% of the packet delivery rate (PDR).

A Wireless Body Area Sensor Network (WBASN) is combination of numerous sense nodes, positioned onto/close or inside a person body. Wireless Body Area Sensor Networks (WBASN) is a developing automation trend that exploits wireless sensor nodes to put instantaneous wearable well-being of ill person to improve individual’s existence. The sensor nodes might be used outwardly to observe abundant health parameters (like heart activity, blood pressure and cholesterol) of an ill person at a vital site within hospital. Hence the goal of WBASN is much crucial, enhancing the lifetime of nodes is compulsory to sustain many issues such as utility and efficiency. It is essential to evaluate time that when the first node will die it we want to refresh or change the battery reason is that loss of crucial information is not tolerable. The lifetime is termed as the time interval when a first node dies out due to battery exhaustion. In our proposed protocol life time of a network is the main concern as well other protocol related issues such as throughput, path loss, and residual energy. Bio-sensors are used for deployment on human body. Poisson distribution and equilibrium model techniques have been used for attaining the required results. Multi-hop network topology and random network node deployment used to achieve minimum energy consumption and longer network lifetime.

In this study, we propose a module-type triboelectric nanogenerator (TENG) capable of harvesting power from a variety of mechanical energy sources. The potential energy and kinetic energy of water are used for the rotational motion of the generator module, and electricity is generated by the contact/separation generation mode between the two triboelectric surfaces inside the rotating TENG. Through the parametric design of the internal friction surface structure and mass ball, we optimized the output of the proposed structure. To magnify the power, experiments were conducted to optimize the electrical output of the series of TENG units. The electrical signal generated by the module-type TENG can be used as a sensor to recognize the strength and direction of various physical quantities, such as wind or earthquake vibrations.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

Underwater wireless sensor networks (UWSNs) represent a specialized category of WSNs with versatile applications including acoustic monitoring, oil and gas exploration, and military surveillance. UWSNs face formidable challenges such as limited energy resources, extended propagation delays, and harsh conditions. Existing clustering and multi-hop routing protocols often unevenly distribute nodes geographically, causing network fragmentation and disproportionately draining the battery life of nodes near the sink due to higher data transmission demands. In this paper, we introduce an Energy-efficient Artificial Fish Swarm-based Clustering Protocol (EAFSCP), inspired by the collective behavior of fish swarms. EAFSCP is a decentralized clustering algorithm designed for acoustic monitoring in UWSNs. Its decentralized nature makes it particularly well-suited for large-scale UWSNs, where centralized algorithms may not be feasible. Through comprehensive comparisons with existing cluster-based routing protocols, our findings indicate that EAFSCP consistently outperforms them across multiple key performance metrics, including network lifetime, energy consumption, packet delivery ratio, packet loss rate, and throughput. According to the results, EAFSCP represents an effective clustering algorithm that enhances network performance, prolongs network lifespan by reducing energy consumption, promotes scalability, and provides valuable guidance for emergency response efforts.

The evolution of transportation has been inextricably tied to the progress of civilization. Through innovation, the automobile business has been working to improve safety, quality, and compliance with environmental regulations. Electric vehicles have made significant strides in this area, but optimizing their efficiency requires a special focus because they expend energy that can be recovered in a variety of ways. Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, has recently received a lot of attention as it constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses. This study tenders a thorough examination into energy recovery technologies which could be applied to the various types of energy dissipated in electric vehicles. Firstly, the paper investigates the possible sources of energy recoverable from an electric vehicle, as well as the various types of energy dissipated. Secondly, the article examines the energy recovery technologies most frequently used in vehicles, categorizing them according to the type of energy and application. Finally, it determines that with further research and development, energy harvesting holds considerable potential for improving the energy efficiency of electric vehicles. New and innovative methods for capturing and utilizing wasted energy in electric vehicles can be established. The potential benefits of applying energy recovery systems in electric vehicles is a vital issue for the automobile industry to focus on due to the potential benefits involved. The ongoing progress currently being made in this field is expected to play a significant role in shaping the future of transportation.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

One of the challenges of deploying Wireless Sensor Networks (WSN) at large scale is to operate for prolonged periods of time relying on the limited amounts of energy stored in its nodes. Generally, data communication is the main factor of draining energy. Consequently, reducing the amount of transmitted data by the nodes is of great interest. At the same time, reducing data to be transmitted should not decrease the quality of the deduced information. Solving this problematic is what we call in this article "Ensuring the Quality of Information Service (QoIS)". This document provides a state-of-the-art for the QoIS regarding WSNs. At first, we give a quick overview of the Internet of Things (IoT) paradigm and the WSN technologies in order to understand how data is gathered and used in these networks. Also, we introduce a novel concept: QoIS, in contrast with classic QoS. Then, it is expected a summary of criteria that asses the QoIS in WSNs plus some techniques to improve it. In this article, we will focus on data management techniques. These techniques can improve raw data, information and/or knowledge quality in energy-constrained WSNs. Finally, we give some conclusions and a glimpse about our future work.

Since the requirements in terms of power of the electronic applications range wide, the developed Energy Harvesting (EH) systems limit their availability to the less power demanding applications. However, this paper focuses on increasing the energy levels collected in the EH system so that it can be included in more demanding applications in terms of power. Therefore, an electronic system capable of grouping many single harvesting channels into one single system is analyzed in this paper. This multi-harvester electronic system is able to manage efficiently the energy collected by multiple vibratory transducers. The paper includes a comparison of its performance against some of the State-of-the-Art EH energy management circuits that interface the transducers. The method employed to demonstrate the intrinsic efficiency of each of the electronic circuits tested was based on experimental tests, where the average power transferred from several identical and simultaneous electric sources to a single storage element was measured. It was found out that only one energy management circuit was able to increase the transferred energy in a linear way while new input electric sources were added.

The radio activity in Wireless Sensor Networks (WSN) and Internet of Things (IoT) applications are the most common reason for power consumption. However, recognizing and controlling the factors affecting radio activity can be valuable for managing node power. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS that uses Clear Channel Assessments (CCA) to check radio status periodically. The time taken to check the radio in receive mode WakeUp, is one of the most important reasons for power consumption which in most the cases can lead to negative WakeUp in Radio Duty-Cycles and ContikiMAC especially. Here, we present a detailed analysis of idle listening time factors on the ContikiMAC. Then, we propose Light Weight CCA(LW-CCA) as an extension to ContikiMAC to reduce power consumption by reducing the radio check time in receive mode WakeUp’s, while maintaining up to 99% the Packet Delivery Rate (PDR). The simulation results show that the proposed method reduces significantly energy consumption in nodes compared to ContikiMAC and thus it helps maintain a high network performance.

he present experiment concerns deposition of ZnO by ALD and subsequent growth of nanowires by chemical bath. We used a novel AISI 301 steel substrate with mechanical parameters that make it suitable to use as a piezoelectric component in an energy harvesting device. We found out that a thin layer of another oxide below ZnO provides outstanding adhesion. Without it, ZnO exhibits island growth and is mechanically unstable. Such prepared samples were placed under repeated mechanical stress. They showed a piezoelectric signal which is stable after hundreds of actuations. This shows good promise for use of our device based on ZnO, an earth-abundant and non-toxic material, as an alternative to widespread in piezo components but environmentally unfriendly PZT. The piezo layers generated enough power for operations performed by a IoT chip. The designed measurement setup allowed for the demonstration of an application of AISI 301 steel substrate coated with ZnO by atomic layer and chemical bath deposition techniques as a piezoelectric component capable of generating energies usable in Internet of Things applications.

Thermoelectric materials may be used in devices as thermoelectric “air conditioner” in a smart house for improved energy efficiency. Energy harvesting uses ambient energy to generate electricity. It provides potentially low-cost, maintenance-free, long-life equipment by reducing the need for batteries or power chords. Energy harvesting (EH) is also known as power harvesting or energy scavenging. EH is considered to give benefits related to environmental friendliness, safety, security, convenience and affordability. EH can be used for brand enhancing. Technically, it can be used to make new things possible depending on visionary engineering. The variety of thermoelectric (TE) materials that can be used in energy harvesting is quite large, and the optimal material for a given application depends mainly on the temperature range in which the material is to be used. In this work we study the development and characterization of thermoelectric materials which were prepared by two different method, which were: a) ball-milling followed by sintering and b) ball-milling, microwave synthesis, high energy planetary ball milling, and sintering. Finally, we study the thermoelectric properties, calculate the band gaps and the ZT for the thermoelectric materials.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

Solar pavement technology has numerous benefits for advanced life and environmental protection, including reduced fossil fuel usage, reduction harmful emissions from conventional electricity generation and handy reliable electricity via solar energy. This paper aims to find an alternative for cost effective renewable energy sources is in conjunction with the principles of sustainability. This research studies whether the application of thermal energy harvesting road pavement using sustainable conductive piping such as stainless steel, copper, and aluminium are feasible in Malaysia. The scope of the paper is to optimize the suitable parameters for different materials of thermal energy harvester such as pipe material, pipe depth inserted into pavement, types of pipe arrangement, pipe spacing, and flow rate for maximum thermal energy extraction using numerical simulation. The simulation is testing under engineering software ANSYS Workbench 19.2 (Fluent) and Solidworks 2020 to develop project prototype from optimize thermal energy harvester. Thus, serpentine copper pipe shows the highest heat efficiency which is 32.22% with the temperature outlet of 327.35K (54.21°C) at the pipe located at 50 mm from the surface pavement with the pipe spacing of 80 mm centre-to-centre.

Geoenvironmental engineering involves defining solutions for complex problems, such as containment systems management, contaminant transport control, wastewater management, remediation of contaminated sites and valorization of geomaterials and wastes. In the last years, energy harvesting (EH) - or energy scavenging - methods and technologies have been developed to reduce the dependence on traditional energy sources, namely fossil fuels, and nuclear power, also responding to the increase of energy demands for human activities and to fulfill sustainable development goals. EH in geoenvironmental works and surrounding soil and water environment include a set of processes for capturing and accumulating energy from several sources considered deemed wasted or unusable associated to soil dynamics, stress and strain of geomaterials, hydraulic, vibrations, biochemical, light, heating and wind sources can be potential EH systems. Therefore, this work presents a review of the literature and critical analysis on the main opportunities for EH capturing, accumulating and use in geoenvironmental works, among basic electric concepts and mechanisms, analyzing those works in complex conditions involving biological, chemical, mechanical, hydraulic, and thermal coupled actions, concluding with the main investigation and challenges within geoenvironmental aspects for EH purpose.

Nanostructured dipeptide self-assemblies exhibiting quantum confinement are of great interest due to their potential applications in the field of materials science as optoelectronic materials for energy harvesting devices. Among those, aromatic cyclo-dipeptides containing the amino acid tryptophan are wide-band gap semiconductors displaying high mechanical rigidity, photoluminescence and piezoelectric properties to be used in power generation. In this work, we report the fabrication of hybrid systems based on chiral cyclo-dipeptide L-Tryptophan- L-Tryptophan incorporated into biopolymer electrospun fibers. The micro/nanofibers contain self-assembled nanospheres embedded into the polymer matrix are wide-band gap semiconductors (gap energy 3.8 eV), display blue photoluminescence and relevant piezoelectric and pyroelectric properties with coefficients as high as 57 pCN-1 and 35×10-6 Cm-2k-1, respectively. They are therefore promise systems for thermal sensing and energy harvesting applications.

Demand for green technologies and energy is in continuous growth in the last years. Compact efficient antennas are crucial for energy harvesting portable systems. Small antennas have low efficiency. The efficiency of communication and energy harvesting systems may be improved by using efficient passive and active antennas. The system dynamic range may be improved by connecting amplifiers to the printed antenna feed line. Design, design considerations, computed and measured results of wearable meta-materials antennas with high efficiency for energy harvesting applications are presented in this paper. All antennas were analyzed by using 3D full-wave software. The antennas electrical parameters on human body are presented. The directivity and gain of the antennas with Split-ring resonators, SRR, is higher by 2.5dB than the antennas without SRR. The resonant frequency of the antennas with SRR is lower by 5% to 10% than the antennas without SRR.

This study introduces a neural network-based approach to predict dust emission, specifically PM2.5 particles, during almond harvesting in California. Using a feedforward neural network (FNN), the research predicts PM2.5 emissions by analyzing key operational parameters of an advanced almond harvester. The model is trained on extensive field data from the almond pickup system, including variables like brush speed, angular velocity, and harvester forward speed. The results demonstrate a notable predictive accuracy of the FNN model, with a Mean Squared Error (MSE) of 0.02 and a Mean Absolute Error (MAE) of 0.01, indicating a high degree of precision in forecasting PM2.5 levels. The study also finds a strong correlation between certain operational parameters and PM2.5 emissions, highlighting specific areas for optimization in harvesting techniques. By integrating machine learning with agricultural practices, this research provides a significant tool for environmental management in almond production, offering a method to reduce harmful emissions while maintaining operational efficiency. This model presents a solution for the almond industry and sets a precedent for applying predictive analytics in sustainable agriculture.

This study describes the synthesis, and characterization of lead-free organic ferroelectric perovskite N-methyl-N’-diazabicyclo[2.2.2]octonium)-ammonium trichloride (MDABCO-NH4Cl3). The electrospinning technique was employed to obtain nanofibers embedded with this perovskite into PVC polymer for hybrid fiber production. The dielectric, piezoelectric and pyroelectric properties of these fibers were carefully examined. From measurements of the dielectric permittivity temperature and frequency dependence, together with the pyroelectric results, a transition from a high temperature paraelectric to a ferroelectric phase that remained down to room temperature, was found to occur at 438 K. A pyroelectric coefficient as high as 290 C K-1 m-2value obtained is within the same order of magnitude as that reported for MDABCO-NH4I3 and the semiorganic ferroelectric triglycine sulfate (TGS). The hybrid nanofibers exhibited good morphological characteristics and demonstrated very good piezoelectric properties. Specifically, a piezoelectric coefficient of 42 pC/N was obtained when a periodical force of 3 N was applied. The performance of these fibers is on par with materials discussed in the existing literature for fabrication of nano energy harvesting generators. Importantly, the perovskite nanocrystals within the fibers not harmed by oxidation, making them a promising environmentally friendly platform for flexible energy harvesting.

This work presents the design and analysis of a novel metal-insulator-insulator-metal (MIIM) rectenna with an added meta lens on top of it for efficient and robust infrared (IR) energy harvesting at 28.3 THz. To ensure maximum transfer of the captured IR radiations by an antenna with better impedance matching, the log-spiral antenna terminals are used as rectenna electrodes while two different insulators are placed between its feeding terminals to form the MIIM rectenna. A split ring-based resonating metasurface is designed and placed on the top of the MIIM rectenna to focus the incoming electromagnetic radiations. The characterization of the MIIM rectenna with added meta lens, in terms of absorbed E-field, is performed for the four different work function metals (gold aluminum, silver, and copper) as well as four combinations of aluminum oxide, titanium oxide, zinc oxide, and copper oxide as insulators. The focusing of illuminating IR radiations by the integrated meta lens to the rectenna structure enhances its field-capturing characteristic by more than 400% as compared to conventional structures. In addition, the proposed design shows improved rectification properties in terms of better impedance matching and rectification efficiency, particularly for the best configuration of Au-Al2O3-Cu2O-Cu rectenna with added metasurface. Future applications of this study include the development of efficient IR energy harvesting systems for remote sensing, wireless communication, and other IoT devices.

The phycobilisomes (PBS) of cyanobacteria and red algae are the primary light-harvesting an-tennas, absorbing solar energy and transporting it to photosynthetic reaction centres with ex-traordinary efficiency and rate. The mechanism of energy transfer in PBS should be investigated in conjunction with biological structural information, as the functions of proteins result from structures. Here, we report the energy transfer study in PBS from a thermophilic cyanobacte-rium Thermosynechococcus vulcanus NIES 2134 (T. 2134), with the Cryo-EM model resolved at near-atomic-resolution recently. The time-resolved fluorescence spectroscopy of PBS with the sub-picosecond resolution was discovered at 77K. Deconvolution of the fluorescence decay curve was then used to reveal the energy transfer channels and the associated transfer rates. Expert for the fluorescence lifetimes of terminal emitters, four time-components, i.e., 9 ps, 13 ps, 23 ps, and 55 ps, were recognised in the energy transfer in PBS. The energy transfer dynamics in PBS were further analysed by combining the cryo-EM structure and the spectral property. The findings aid our understanding of the energy transfer mechanisms in PBS.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

In this paper, modification of dual-Halbach permanent magnet (PM) array is investigated to improve performance of tubular linear machine, in terms of flux density and output power. Instead of a classical Halbach array with only radial and axial PMs, proposed model involves insertion of mig-magnets, which have magnetized angle shifted from the reference magnetized angles of axial and radial PMs. This structure leads to elimination of flux leakage and concentration of flux linkage in middle of the coil; therefore, the performance of machine is increased.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

Almost fifty years after the first installations, I identify the main lessons learned from fighting drought and poverty in Africa with direct solar-powered pumps thanks to Father Bernard Verspieren and Mali Aqua Viva. Six main findings and three main recommendations emerge from the present analysis. They are of direct relevance to all Africa’s countries whose population has gone from 438 million in 1977 to 1,308 million in 2019, with about 600 million still having no access to electricity. In place of “awareness campaigns” and extraordinary courses held by international organizations, I recommend to establish national solar energy institutes whose task will include the education of solar energy professionals giving practice-oriented workshops on solar-powered drip irrigation and rainwater harvesting throughout each Africa’s country. Said education will critically include the economic and social aspects of distributed “generation” of energy and water from sunlight and rainfall.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

For thermoelectric materials study and development, it is very important to measure the electrical power and efficiency of a thermoelectric generator (TEG). In this study, thermoelectric properties such as electrical conductivity, Seebeck coefficient, and thermal conductivity of cement composites with graphene nanoplatelets and metallic oxides (Fe2O3, ZnO, MnO2) are measured and subsequently used to figure out the output electrical power and efficiency. A maximum of 1.5 W power per square meter for a temperature difference of about 50 °C can be estimated using GnP-ZnO added cement composites. This paper also talks about how to make a cement composite-based structural TEG module to enhance the total output voltage, power, and efficiency of the system.

Smart air filters are beneficial to provide highly efficient particle removal, treat multiple contaminants simultaneously and conserve energy during air filtration processes. Herein, a type of self-supporting smart air filter (SSSAF) was fabricated by sandwiching the VOC-responsive PZT/PVDF electrospun membrane with two metal mesh electrodes. Besides the high filtration efficiency for sub-micron particles, the SSSAF showed good responses to pressure drop in the range of 0 to 500 Pa via the electroactivity of PZT/PVDF membrane. In addition, the SSSAF achieved VOC sensing function via the swelling properties of PZT/PVDF membrane in organic vapors, demonstrated by its signal to 50 to 200 ppm ethanol gases. The SSSAF based nanogenerator was employed to harvest wind energy, which was further applied to inhibit bacterial growth without the need of additional power input. The results provide new insight into development of all-in-one smart air filters.

The field of power harvesting has experienced significant growth over the past few years due to the ever-increasing desire to produce portable and wireless electronics with extended lifespans. The present work aims to introduce an approach to harvesting electrical energy from a mechanically excited piezoelectric element and investigates a power analytical model generated by a smart structure of type polyvinylidene fluoride(PVDF) that can be stuck onto fabrics and flexible substrates, although we report the effects of various substrates and investigates the sticking of these substrates on the characterization of the piezoelectric material.

In this study, three paddy harvesting systems; manual harvesting of paddy (MHP), reaper harvesting of paddy (RHP), and combine harvesting of paddy (CHP) were evaluated considering field capacities, field efficiencies, time and fuel consumption, mechanization indices, greenhouse gas emissions, straw availability, and direct and indirect costs. Field experiments were conducted in North central province of Sri Lanka. The effective field capacity, field efficiency and fuel consumption of the combine harvester were 0.34 hah-1, 60.8%, and 34.1 Lha-1, respectively, and those of the paddy reaper were 0.185 hah-1, 58.2%, and 3.8 Lha-1, respectively. The total time consumed by MHP, RHP, and CHP were 76.05 hha-1, 39.76 hha-1, and 2.94 hha-1, respectively. The highest energy utilization was recorded by the CHP, at 1851.09 MJha-1, while MHP recorded the lowest at 643.20 MJha-1. The direct cost of the MHP was 1.50 and 1.52 times higher than those of the CHP and RHP, respectively. MHP recorded the lowest greenhouse gas emissions (32.94 kgCO2eqha-1), while CHP recorded the highest (176.29 kgCO2eqha-1). The RHP exhibited an intermediate level in all aspects. Although the CHP has higher field performance and direct costs, it brings higher GHG emissions and indirect costs. Therefore, an optimum level of mechanization should be introduced for the long-term sustainability of both the environment and farming.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

The Unmanned Aerial Vehicles (UAVs), used in civilian applications such as emergency medical deliveries, precision agriculture, wireless communication provisioning, etc., face the challenge of limited flight time due to their reliance on the on-board battery. Therefore, developing efficient mechanisms for in-situ power transfer to recharge UAV batteries hold potential in extending their mission time. In this paper, we study the use of far-field wireless power transfer (WPT) technique from specialized, transmitter UAVs (tUAVs) carrying Multiple Input Multiple Output (MIMO) antennas for transferring wireless power to receiver UAVs (rUAVs) in a mission. The tUAVs can fly and adjust their distance to the rUAVs to maximize energy transfer. The use of MIMO antennas further boost the energy reception by narrowing the energy beam toward the rUAVs. The complexity of their dynamic operating environment increases with the growing number of tUAVs, and rUAVs with varying levels of energy consumption and residual power. We propose an intelligent trajectory selection algorithm for the tUAVs based on a deep reinforcement learning model called Proximal Policy Optimization (PPO) to optimize the energy transfer gain. Simulation results demonstrate that with the use of PPO, the system achieves a tenfold flight time extension compared to no wireless recharging. Further, PPO outperforms the benchmark movement strategies of ’Traveling Salesman Problem’ and ’Low Battery First’ when used by the tUAVs.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

Ocean wave energy conversion as one of the renewable clean energy sources is attracting the research interests of many people. This review introduces different types of power take-off technology of wave energy converters. The main focus is the linear direct drive power take-off devices as they have the advantages for ocean wave energy conversion. The designs and optimizations of power take-off systems of ocean wave energy converters have been studied from reviewing the recently published literature. Also, the simple hydrodynamics of wave energy converters have been reviewed for design optimization of the wave energy converters at specific wave sites. The novel mechanical designs of the power take-off systems have been compared and investigated in order to increase the energy harvesting efficiency.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m3) can be enhanced by approximately 484% in a composite (56.86 MJ/m3) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

Deep brain stimulation (DBS) is an effective and safe medical treatment that improves the lives of patients with a wide range of neurological and psychiatric diseases, and has been consolidated as a first-line tool in the last two decades. Closed loop deep brain stimulation (CLDBS) pushes this tool further by automatically adjusting the stimulation parameters to the brain response in real-time. This paper presents a CLDBS with 2 stimulation channels and 2 acquisition channels. Each channel has a low-noise amplifier (LNA) buffer in differential configuration to eliminate the DC signal component of the input. Energy management is efficiently done by the control and communication unit. The battery supports almost 9 hours with both the acquisition and stimulation circuits active. If only the stimulation circuit is used as an Open Loop DBS (OLDBS), the battery can hold sufficient voltage for 24 hours of operation. The whole system is low-cost and portable and therefore it could be used as a wearable.

This comparative research paper examines the difference between sugarcane harvesting practices in Thailand and India. The objective of research was to investigate and compare current pattern of sugar harvesting and its impact of these approaches on labor health conditions in the sugarcane industry of both the countries as India and Thailand. Data were collected from target population groups (40 each) from study areas, namely Kanchanaburi and Saraburi provinces in Thailand and Beed District of Maharashtra state from India. The data showed that comparatively in Thailand, adoption of mechanized harvesting was seen more. However in India, mechanized harvesting was seen increasing but still people were largely involved in sugarcane harvesting and it had ill effects on the overall health of female workers specially. The result clearly indicated that there was drastic difference in harvesting system and labor health conditions in Thailand and India. The findings underscore the multifaceted impact of their occupation on various aspects of health including general well-being of female sugarcane cutters. The strenuous nature of sugarcane cutting, coupled with inadequate protective measures and limited access to healthcare has contributed to a range of health care challenges among female sugarcane cutters in India.

The recent advancements in the field of communication have led data sharing to become an integral part of today's smart cities with the evolution of concepts such as the internet of vehicles (IoV) paradigm. As a part of IoV, Electric Vehicles (EVs) have recently gained momentum as authorities have started expanding their Low Emission Zones (LEZ) in an effort to build green cities with low carbon footprints. Energy is one of the key requirements of EVs not only to support the smooth and sustainable operation of EV itself but to also ensure connectivity between the vehicles and infrastructure with controlling devices like sensors and actuators installed within an EV. In this context, renewable energy sources (such as wind energy) dramatically play their parts in the automobile sector towards designing the energy harvesting electric vehicles (EH-EV) to pare the energy reliance on the national grid. In this article, a novel approach is presented to achieve electric generation due to vehicle mobility to support the communication primitives in electric vehicles which enables plenty of IoV use cases in the presence of surplus energy at hand. A small-scale wind turbine is designed to harness wind power for converting it into mechanical power. This power is then fed to the onboard DC generator to produce electrical energy. Furthermore, the acquired power is processed through a regulation circuitry to consequently achieve the desired power supply for the end load, i.e. the batteries installed. The suitable orientation for efficient power generation is proposed on ANSYS-based aerodynamics analysis. The voltages induced by DC generator at No-Load condition are 35V while at Full-Load 25V are generated at rated current of 6.9A, along with the generation of power at around 100W (at constant voltage) at the rated speed of 90 mph for nominal battery charging. Moreover, the acquired data can be monitored via an android application interface by using a Bluetooth module.

This paper reviews the design and component of two types of RWHS, namely roof harvesting system (RHS) and pond harvesting system (PHS). The performance in terms of quantity and quality of collected rainwater and energy consumption for RWHS with different capacities were evaluated, as well as the benefits and challenges particularly in environmental, economic and social aspects. Presently, RHS is more commonly applied but its effectiveness is limited by its small scale. The PHS is of larger scale and has greater potentials and effectiveness as an alternative water supply system. Results also indicate the many advantages of PHS especially in terms of economics, environmental aspects and volume of water harvested. While RHS may be suited to individual or existing buildings, PHS has greater potentials and should be applied in newly developed urban areas with wet equatorial climate.

Unmanned aerial vehicles (UAVs)-based communication system is a promising solution to meet coverage and capacity requirements of future wireless networks. However, UAV-enabled communications is constrained with its coverage, energy consumption, and flying regulations, and the number of works focusing on the sustainability aspect of UAV-assisted networking has been limited in the literature so far. In this paper, we propose a solution to this limitation; particularly, we design a $Q$-learning-based UAV positioning scheme for sustainable wireless connectivity considering key constraints, that are, altitude regulations, non-flight zones, and transmit power. The objective is to find the optimal position of the UAV base station (BS) and minimize the energy consumption while maximizing the number of users covered. Moreover, a weighting mechanism is developed, where the energy consumption and number of users covered can be prioritized according to network/battery conditions. The proposed Q-learning-based solution is compared to the baseline k-means clustering method, where the UAV BS is positioned at the centroid location that minimizes the cumulative distance between the UAV BS and the users. The results demonstrate that the proposed solution outperforms the baseline k-means clustering-based method in terms of the number of users covered while achieving the desired minimization of the energy consumption.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

In recent years, the application of Indoor Positioning Systems (IPS) has experienced a significant increase in demand, with the aging of the world’s population and their changing lifestyles. While outdoor positioning systems, such as the Global Positioning System (GPS), have significantly advanced over the years, indoor positioning has been restrained by the limitations of the employed technologies. This paper presents a hybrid wireless positioning system able to locate wearables indoor accurately. It is based on the Wi-Fi and Bluetooth technologies, by using trilateration to determine the position of Bluetooth low energy (BLE) wearable devices with an accuracy of up to 1.8 meters. A graphical user interface (GUI) was used to illustrate the performance of the proposed systems, by allowing users to visualize the captured data in two dimensions and three- dimensions in real-time.

The application of thermoelectric generators (TEG) on the nozzle of an aviation jet engine was studied by finite element TEG-simulations. Against the background of system-level requirements of the reference aircraft this work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and fill factors (F) within the TE modules in order to maintain a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients at the nozzle surfaces this work reports the achievable power output. System-level requirement on the gravimetric power density (> 100 Wkg-1) can only be met for F ≤ 21%. Extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. Assessment of further potential is demonstrated by a parametric study on the fill factor, convective heat transfer coefficients, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient installation of TEG in consideration of the cost-specific power output of modern thermoelectric materials.

This paper presents the design and implementation of a versatile IoT testbed utilizing the openHab platform along with various wireless interfaces, including Z-Wave, ZigBee, WiFi, 4G-LTE, and IR, and an array of sensors for motion, temperature, luminance, humidity, vibration, UV, and energy consumption. First, the testbed architecture, setup, basic testing, and collected data results are described. Then, by showcasing a typical day in the laboratory, we illustrate the testbed's potential through the collection and analysis of data from multiple sensors. The study also explores the capabilities of the openHab platform, including its robust persistence layer, event management, real-time monitoring, and customization. The significance of the testbed in enhancing data-collection methodologies for energy assets and unlocking new possibilities in the realm of IoT technologies is particularly highlighted.

Although train simulation research is vast, most available network simulators do not track the instantaneous movements and interactions of multiple trains for the computation of energy/fuel consumption. In this paper, we introduce the NeTrainSim simulator for heavy long-haul freight trains on a network of multiple intersecting tracks. Trains are modeled as a series of moving mass points (each car/locomotive is modeled as a point mass) while ensuring safe following distances between them. The simulator considers the motion of the train as a whole and neglects the relative movements between the train cars/locomotives. Furthermore, the powers of the different locomotives are transferred to the first locomotive as such a simplification result in a reduced simulation time without impacting the accuracy of energy consumption estimates. While the different tractive forces are combined, the resistive forces are calculated at their corresponding locations. The output files of the simulator contain pertaining information to the train trajectories and the instantaneous energy consumption levels. A summary file is also provided with the total energy consumed for the full trip and the entire network of trains. Two case studies are conducted to demonstrate the performance of the simulator. The first case study validates the model by comparing the output of NeTrainSim to empirical trajectory data using a basic single-train network. The results confirm that the simulated trajectory is precise enough to estimate the electric energy consumption of the train. The second case study demonstrates the train-following model considering six trains following each other. The results showcase the model’s ability in relation to maintaining safe-following distances between successive trains. Finally, the NeTrainSim is demonstrated to be scalable with computational times of O(n) for less than 50 trains (n) and O(n²) for higher number of trains.

Due to its spatio-temporal variability, the mismatch between the weather and demand patterns challenges the design of highly renewable energy systems. A principal component analysis is applied to a simplified networked European electricity system with a high share of wind and solar power generation. It reveals a small number of important mismatch patterns, which explain most of the system's required backup and transmission infrastructure. Whereas the first principal component is already able to reproduce most of the temporal mismatch variability for a solar dominated system, a few more principal components are needed for a wind dominated system. Due to its monopole structure the first principal component causes most of the system's backup infrastructure. The next few principal components have a dipole structure and dominate the transmission infrastructure of the renewable electricity network.

The increasing expansion of the use of renewable distributed generation (RDG) technologies in electrical networks such as solar plants or wind farms and others has changed the nature of the distributed system and transformed it from the traditional system into an efficient system. This system has led to various technical effects in the host networks, with regard to voltage, electrical energy losses, fault levels, stability and electrical energy quality. These effects are not generic to any network; It can be positive, negative or neutral depending on the structure of the studied network, its operational condition and the various technology of the distributed generators. This research aims to quantitatively correct the effects of (RDG) in terms of voltage and electrical energy losses in the host networks. , since efficient distribution systems contain generators of a special nature and often contain bidirectional flux energy, it was necessary to construct a mathematical model of the distribution system hosting RDG units, which is fundamentally different from the traditional model of defining the reference electrical distribution bus bar. In order to achieve the systematic analysis, evaluation criteria and indicators were determined and mathematical formulas for them were completed. Based on the accomplished mathematical basis, an algorithm designed in such a way that it can be applied to any multi-voltage distribution system and to different distributed regenerative generation techniques is proposed. To demonstrate the algorithm's capabilities, it was tested on typical distribution networks using Factory Power DigSilent software, which is somewhat similar to MATLAB but more suitable for large capacity systems.

The paper proposes a methodological way to compensate the imbalance between energy generation and consumption using the battery block of electric vehicles as energy reservoir through the well-known Vehicle to Grid system (V2G). The method is based on a simulation process developed by the authors that take into consideration the daily fluctuations of energy consumption as well as the power level generated by an energy source, either conventional, renewable or hybrid. The study shows that for very large electric vehicle fleet the system renders non-viable, since the remaining energy in the battery block to let the electric vehicle usable for running during daytime avoids to compensating for the energy grid imbalance, only allowing to cover a percentage of the energy imbalance, which the proposed methodology may optimize. The analysis of the proposed methodology also shows the viability of the system when being applied to a small fleet of electric vehicles, not only compensating for the energy imbalance but also preserving the required energy in the battery of the electric vehicle to make it run. The method allows predicting the optimum size of electric vehicle battery, which depends on the energy generation level, coverage factor of the energy imbalance and size of the electric vehicle fleet.

The Robotics Vision Lab of Northwest Nazarene University has developed Orchard Robot (OrBot), which was designed for harvesting fruits. OrBot is composed of a machine vision system to locate fruits on the tree, a robotic manipulator to approach the target fruit, and a gripper to remove the target fruit. Field trials conducted at commercial orchards for apples and peaches during the harvesting season of 2021 yielded a harvesting success rate of about 85% and had an average harvesting cycle time of 12 seconds. Building upon this success, the goal of this study is to evaluate the performance of OrBot during nighttime harvesting. The idea is to have OrBot harvest at night, and then human pickers continue the harvesting operation during the day. This human and robot collaboration will leverage the labor shortage issue with a relatively slower robot working at night. The specific objectives are to determine the artificial lighting parameters suitable for nighttime harvesting and to evaluate the harvesting viability of OrBot during the night. LED lighting was selected as the source for artificial illumination with a color temperature of 5600 K and 10% intensity. This combination resulted with the lowest noise in the images. OrBot was tested in a commercial orchard using twenty Pink Lady apple trees. Results showed an increased success rate during the night, with OrBot gaining 94%. compared to 88% during the daytime operations.

This publicly available simulation analysis compares baseline construction options versus sustainable options and evaluates both break-even costs as well as environmental effects. The simulation (https://rminator.shinyapps.io/sustain4/) provides users with comparative estimates based upon existing research on costs. This is the first simulation of its type that quantifies multiple sustainable construction options, associated break-even points, and environmental considerations for public use. Results estimate that a 100% solar solution for the baseline 3,000 square foot / 279 square meter house with 2 occupants results in a break-even of 9 years. The simulation includes options for rainwater harvesting or wells, Icynene foam, engineered lumber, Energy Star windows and doors, low flow water fixtures, aerobic / non-aerobic waste treatment or municipal services, and many other options. This is the first simulation of its type to provide publicly available sustainable construction analysis based on research, and it illustrates that sustainable construction might be both green for the environment and green for the pocketbook.

A major goal of neuroscience is understanding how neurons arrange themselves into neural networks that result in behavior. Most theoretical and experimental efforts have focused on a top-down approach which seeks to identify neuronal correlates of behaviors. This has been accomplished by effectively mapping specific behaviors to distinct neural patterns, or by creating computational models that produce a desired behavioral outcome. Nonetheless, these approaches have only implicitly considered the fact that neural tissue, like any other physical system, is subjected to several restrictions and boundaries of operations.Here, we propose a new, bottom-up conceptual paradigm: The Energy Homeostasis Principle, where the balance between energy income, expenditure, and availability are the key parameters in determining the dynamics of the found neuronal phenomena from molecular to behavioral levels. Neurons display high energy consumption relative to other cells, with metabolic consumption of the brain representing 20% of the whole-body oxygen uptake, contrasting with this organ representing only 2% of the body weight. Also, neurons have specialized surrounding tissue providing the necessary energy which, in the case of the brain, is provided by astrocytes. Moreover, and unlike other cell types with high energy demands such as muscle cells, neurons have strict aerobic metabolism. These facts indicate that neurons are highly sensitive to energy limitations, with Gibb’s free energy dictating the direction of all cellular metabolic processes. From this activity, the largest energy, by far, is expended by action potentials and post-synaptic potentials; therefore, plasticity can be reinterpreted in terms of their energy context. Consequently, neurons, through their synapses, impose energy demands over post-synaptic neurons in a close loop-manner, modulating the dynamics of local circuits. Subsequently, the energy dynamics end up impacting the homeostatic mechanisms of neuronal networks. Furthermore, local energy management also emerges as a neural population property, where most of the energy expenses are triggered by sensory or other modulatory inputs. Local energy management in neurons may be sufficient to explain the emergence of behavior, enabling the assessment of which properties arise in neural circuits and how. Essentially, the proposal of the Energy Homeostasis Principle is also readily testable for simple neuronal networks.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

Remote patient monitoring systems are helpful since they can provide timely and effective healthcare facilities. Such online telemedicine are usually achieved with the help of sophisticated and advanced wearable sensor technologies. The modern type of wearable connected devices enables the monitoring of vital sign parameters such as: heart rate variability (HRV) also known as electrocardiogram (ECG), blood pressure (BLP), Respiratory rate and body temperature. The ubiquitous problem of wearable devices is power demand for signal transmission, such devices require frequent battery charge which causes serious limitations to the continuous monitoring of vital data. To overcome this, the current study provides a primary report for collecting kinetic energy from human daily activities for monitoring Human vital signs, the harvested energy is used to sustain the battery autonomy of wearable devices, which enables longer monitoring time of vital data. A thorough review of available commercial ECG devices is first provided, and different methods evaluated in other literature to improve the monitoring time of wearable IOT devices. Besides, a novel type of Stress or exercise ECG monitoring device based on Microcontroller PIC18F4550 and Wi-Fi device ESP8266 is proposed in this study, which is cost effective and enables real time monitoring of heart rate on cloud during normal daily activities. In order to achieve both portability and maximum power, the harvester has smallest structure and low friction. Neodymium magnets are chosen for their highest magnetic force. Due to nonlinear magnetic force interaction of the magnets, the nonlinear part of the dynamic equation has inverse quadratic form. Electromechanical damping is considered in this study and the quadratic non linearity is approximated using MacLaurin expansion, which enables to find the law of motion for general case of studies using classical methods for dynamic equations and find the suitable parameters for the harvester. The oscillations are enabled by applying an initial force and there is loss of energy due to the electromechanical damping. A typical numerical application is computed with Matlab software and ODE45 solver is used to verify the accuracy of the method.

The recent provision of energy-harvesting capabilities to wireless sensor networks has entailed the redefinition of design objectives. Specifically, the traditional goal of maximizing network lifetime has been replaced by optimizing network performance, namely delay and throughput. The present paper contributes to this reformulation by considering the routing problem for the class of time-driven energy-harvesting WSN (EH-WSN) under regular or quasi-periodic energy sources. In particular, this paper shows that the minimum hop count (MHC) criterion maximizes the average duty cycle that can be sustained by nodes in this type of scenarios. This is a primary objective in EH-WSN, since large duty cycles lead to enhanced performance. Based on a previous result, a general expression is first obtained which gives mathematical form to the relationship between duty cycle and traffic load for any node in a time-driven EH-WSN fed by a regular energy source. This expression reveals that the duty cycle achievable by a node decreases as its traffic load increases. Then, it is shown that MHC minimizes the average traffic load over the network, and thus it maximizes the average duty cycle of nodes. This result is numerically validated via simulation by comparison with other well-known routing strategies. Accordingly, this paper suggests assigning top priority to the MHC criterion in the development of routing protocols for time-driven EH-WSN under regular energy sources.

IoT system becomes hot topic nowadays for smart home, IoT helps devices to communicate together without human intervention inside home, so it is offering many challenges. A new smart home IoT platform powered using electromagnetic energy harvesting is proposed in this paper. It contains a high gain transmitted antenna array and efficient circular polarized array rectenna system to harvest enough power from any direction to increase life time of the batteries used in IoT system. Optimized energy consumption, the software with adopting the Zigbee protocol of the sensor node and low power microcontroller are used to operate in lower power modes. The proposed system has an 84.6 days lifetime which is approximately 10 times the lifetime for similar system. On the other hand, the proposed power management circuit operated at 0.3 V DC to boost the voltage to ~3.7V from radio frequency energy harvesting and manage battery level to increase the batteries lifetime. A predictive indoor environment monitoring system is designed based on a novel hybrid system to provide a non-static plan, approve energy consumption and avoiding failure of sensor nodes in smart home.

High electricity demand for consumption at current supply level in Indonesia led to the rising cost of electricity bills. This factor is compounded by the fact that many electric generators in Indonesia still use fossil fuels, which contributes to the high basic generation cost. UBL is one of the universities that aim to be a green campus. Our research explores the possibility of installing motion sensor to contribute on the energy efficiency. Although mostly common in developed countries, the use of motion sensor for energy efficiency is still rare, especially in Indonesia. despite rising cost and supply shortages, Indonesian buildings are still of high energy consumption. our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. One of the efforts to lower energy demand in consumer side is to use the electricity efficiently, such as turning off lights in a room when it's not in use. This method can be simply done by turning the light switches for office and classrooms, but difficult to do in public spaces such as toilets and corridors. Our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. Automatic light switches experimentally installed in sample toilet room prove that electricity consumption from the lamps can contribute to the reduction of total weekly energy that translates into Green House Gas emission reduction.

Transfer learning has proven to be a valuable technique for deploying machine learning models on edge devices and embedded systems. By leveraging pre-trained models and fine-tuning them on specific tasks, practitioners can effectively adapt existing models to the constraints and requirements of their application. In the process of adapting an existing model, a practitioner may make adjustments to the model architecture, including the input layers, output layers, and intermediate layers. In this study, we examine the effects of these adjustments on the runtime and energy performance of an edge processor performing inferences. Based on our observations, we make recommendations for how to adjust convolutional neural networks during transfer learning to maintain runtime performance. We observe that the Edge TPU is generally more efficient than a CPU at performing inferences on convolutional neural networks, and continues to outperform a CPU as the depth and width of the convolutional network increases. We explore multiple strategies for adjusting the input and output layers of an existing model and demonstrate important performance cliffs for practitioners to consider when modifying a convolutional neural network model.

The concept of distributed generation has made photovoltaic an integral source of energy in smart grid systems, especially in peer-to-peer energy trading frameworks that exploit excess power to fulfill the energy requirements of consumers in cost-efficient and eco-friendly manner. It is believed that P2P energy trading will dominate a significant portion of research in forthcoming power generation systems due to the excessive rise of energy demands across the globe. Despite a plethora of studies on energy optimization solutions in P2P trading, minimizing nanogrid energy trading cost and efficient energy sharing between consumers and prosumers are deemed among the challenging problems. This study overcomes essential issues overlooked by the contemporary P2P energy trading models by introducing a predictive optimization-oriented nanogrid energy trading model. The proposed study encompasses two stages: (1) predictive optimization model which harnesses BD-LSTM-based forecasted energy parameters (energy load, energy consumption, and PV generation) that are later incorporated in PSO-enabled objective function to reduce nanogrid trading cost, (2) optimal energy sharing plan is devised to decide the role of nanogrids as prosumers or consumers by emphasizing the use of PV-produced energy. The proposed model is validated on the case study containing nanogrid houses data. The simulation provides detailed experiments by comparing the energy demand and response using the proposed energy sharing model. The outcomes yield that the energy sharing plan holds a significant potential to fulfill maximum energy requirements of nanogrid house in P2P cluster and significantly reduces the energy cost compared to grid.

Traditional olive orchards have been grown for thousands of years and still occupy most of the world’s olive cultivation area. To compete with olive oil produced in the higher-yielding intensive orchards, the oil from traditional orchards must be of high quality. We evaluated oil quali-ty—potential and actual (under commercial conditions)—and identified the stages in the pro-duction chain that reduce oil quality in the traditional sector in the Middle East region. Our findings show a clear negative impact of growers' traditional practices on both chemical and sensorial characteristics of the olive oil. The oil originating from the commercial process had higher free fatty acid and lower polyphenol and carotenoid contents, lower stability, lower pungency, fruitiness and bitterness, and a higher prevalence of organoleptic defects than oil originating from fruit picked from the same trees in the experimental procedure. The current, commonly harvesting technique of pole beating significantly increased fruit injury and fruit with mold, leading to a reduction in oil polyphenols and an increase in free fatty acid level compared to manual picking. After harvest, storing the fruit for more than 48 h in plastic bags reduced oil quality dramatically. The traditional olive orchard could potentially be a source of high-quality Extra Virgin Olive Oil. However, handling of the fruit—from the trees until the end of the oil-extraction process—is done incorrectly, adversely affecting oil quality.

South Africa is a water stressed country experiencing mass urbanisation especially towards coastal cities. The country is already enduring the impacts of global warming and climate change with risk of water scarcity in many areas. The risk was evident with Cape Town near encounter with ‘Day Zero’ i.e., the day when water supplies would have been switched off and residents required to queue for daily water rations. The drought exposed the inadequa-cies of the existing water supply system. Paradoxically, in the same drought period, vast amounts of unutilized stormwater that could have augmented water supply run unabated into the ocean through rivers around the city. The study determined that the problem was not necessarily water shortage but lack of adequate water storage. This study investigated the suitability of coastal reservoirs for stormwater harvesting on the over 3000 km South African coastline. The objective was to identify suitable locations for coastal reservoirs. The study un-dertook a systematic process of selecting several candidate locations and eliminating unsuita-ble sites based on international best practice i.e., coastal topography, climate, hydrology, fluvi-al environment, catchment size and river water quality. Nine candidate sites were identified and ranked based on suitability and associated benefits. The identified locations in order of ranking include Knysna River, Berg River, Buffalo River, Kowie River, Thukela River, Orange River, Port of Richards Bay, Port of Durban, and Lourens River. The Knysna site, with a mean annual precipitation of 600 - 800 mm/annum and mean annual runoff of 100 - 500 Mm3/annum, was determined to be the most optimal location.

Root crops grow in the soil deeply and bond with soil closely, which results in that the process of the separation between soil and root becomes the most difficult during the harvesting processes. In order to harvest root crops efficiently, the mechanical harvesting has become the main developing trend. However, high power and high damage rate are still occurred when mechanical harvester gets in touch with the roots. In this paper, we review the research of the development and evaluation of the mechanical harvesting of root crops and its performance optimization on the past years. The process of soil separation mainly consists in the initial separation between root and the ground and further separation between root and adhered soil. In general, the soil-cutting operation in the initial separation and the sieving mechanism in the further separation require high draught and power. And the dramatic friction, impact, pressure and so on, which happen in the components and soil-roots, are the key reasons to lead to root damage. The optimization of harvesting methods and parameters, including the digging shovel shape, working conditions, vibration, and screening way, is more significant in improving the harvesting performance. But there are still some limitations in the research and application of the mechanical harvester for root crops. Future research is suggested to focus on the development of the soil break-up when the digging shovel cutting soil, the insight into the interaction between soil and roots by different external compression loads, and the long-term studies to verify the high-efficiency and low-damage performances of mechanical harvester in practical application.

Reliable prediction of sustainable energy consumption is the key to designing environmental friend buildings. In this study, two novel hybrid intelligent methods, namely grasshopper optimization algorithm (GOA), wind-driven optimization (WDO), and biogeography-based optimization (BBO) is employed to optimize the multitarget prediction of heating loads (HLs) and cooling loads (CLs) in heating ventilation and air conditioning (HVAC) systems. Concerning the optimization of applied hybrid algorithms, a series of swarm-based iteration is performed, and the best structure for the abovementioned methods are proposed. Besides, through sensitivity analyzing the relationship between the HLs and CLs and influential factors are highlighted. In other words, the GOA, WDO, and BBO algorithm are mixed with a class of feedforward artificial neural networks (ANN), which called MLP (multi-layer perceptron) to predict the HLs and CLs. According to the provided sensitivity analysis, the WDO with swarm size = 500 proposes the most proper-fitted terms after it has been combined with optimized MLP. The proposed WDO-MLP (training (R2 correlation=0.977 and RMSE error=0.183) and testing (R2 correlation=0.973 and RMSE error=0.190)) provided accurate prediction in the heating load and (training (R2 correlation=0.99 and RMSE error=0.147) and testing (R2 correlation=0.99 and RMSE error=0.148)) presents the most-fit prediction in the cooling load.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

The power generation from hydroelectric plants has increased worldwide, contributing to the participation of the renewable sources to the energy matrix. In the semiarid Brazilian Northeast (NEB), thousands of small dams have been built over time as a solution for water supply. Although incompatible with hydropower generation due to the conflict with human water supply in the region, small reservoirs accumulate water and hydraulic energy at high altitudes. In this work, simulations were performed to assess how the arrangement of various sized reservoirs impact the power demand for water distribution in the Banabuiú River Basin – BRB (19,800 km²), Brazil. The power required to pump water from all 1,405 reservoirs to the districts is 6.5 GWh/year, whereas in the scenario with the 12 larger strategic reservoirs only, the power demand reaches 45.3 GWh/year. Although representing roughly 60% of the water availability of the BRB and being able to supply all the districts, the Arrojado Lisboa reservoir alone would demand 195 GWh/year to supply water to the entire basin, i.e. 30 times the power required in the real reservoir arrangement. By storing water at high altitudes and distributing it spatially, the small reservoirs increase the energy efficiency on the water distribution system.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

The ubiquitous connectivity for the space-air-ground integrated network (SAGIN) of the beyond fifth generation of communication and sixth generation of communication (B5G/6G) is envisaged to meet the needs for the demanded quality of service (QoS), green communication, and "dual carbon" target. However, the offloading and computation of massive latency-sensitive tasks dramatically increases the energy consumption of the network. Furthermore, the traditional power supply technology of the network base stations (BSs) enhances the carbon emission. To address these issues, we first propose a SAGIN architecture with energy harvesting devices, where the BS is powered by both renewable energy (RE) and the conventional grid. The BS explores wireless power transfer (WPT) technology to power the unmanned aerial vehicle (UAV) for stable network operation. RE sharing between neighbouring BSs is designed to fully utilize RE for reduce carbon emission. Secondly, on the basis of task offloading decision, UAV trajectory, and RE sharing ratio, we construct cost functions with joint latency-oriented, energy consumption, and carbon emission. Then, we develop a twin delayed deep deterministic policy gradient (TD3PG) algorithm based on deep reinforcement learning to minimize the cost function. Finally, simulation results demonstrate that the proposed algorithm outperforms the benchmark algorithm in terms of reducing latency, energy saving, and lower carbon emission.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

To protect power lines, distance relays are used which can rely on a modified distance resistance. But usually the operating range of these relays changes as the network conditions change (network topology, load value, output value, etc.) and leads to false trips, By using methods that can process information and recognize patterns, for example, the use of micro and intelligent processor algorithms can use the new relays with high precision and thus provide adequate protection. In this study, a distance relay was modeled using a neural network, and it was observed that the neural relay had higher accuracy than the conventional relay. In addition to detecting the fault and its location, type and phase of the fault, three-stage simultaneous protection can be performed. As a result, the number of linear relays can be reduced by using relays based on neural technologies. An MLP (multilayer perceptron) neural network is used to model a sequence of distances.