Band-gap alignment engineering has now been extensively studied due to its high potential application. Here we demonstrate a simple route to synthesize two metal oxide layers and align them together according to their bandgaps on surface of crystalline silicon (c-Si) solar cells. The metal oxide layers can not only extend absorption spectrum to generate extra carriers but also serve to separate electron-hole pairs more efficiently. As a consequence, the photovoltaic performance of SnO₂/CdO /Si double-layer solar cell (DLSC) is highly improved compared to CdO/Si and SnO₂/Si single-layer solar cells(SLSCs) and SnO₂/CdO/Si double-layer solar cell (DLSC). By the alignment engineering, the SnO₂/CdO/Si DLSC produces a short circuit photocurrent (J_sc) of 38.20 mA/cm², an open circuit photovoltage (V_oc) of 0.575 V and a fill factor (FF) of 68.7%, corresponding to a light to electric power conversion efficiency (η) of 15.09% under AM1.5 illumination. These results suggest that with the use of metal oxide layers by band-gap alignment engineering, new avenues have been opened for developing high-efficiency and cost-effective c-Si solar cells.

Spectroscopic methods are used to study the processes of accumulation of electron and hole trapping centers and energy transfer of electronic excitations to impurities in CaSO4-Mn and BaSO4-Mn. It is shown that the transfer of energy from the host to impurities occurs at the moment of charge transfer from the excited anionic complex SO_4^(2-) to the hybrid radiative electronic states at 2.95–3.1 eV formed from the electronic states of the Mn^(+)-SO_4^(-) and SO_4^(3-)-SO_4^(-) trapping centers. It was found that, in sulfates, under irradiation, as a result of charge transfer from excited anionic complexes of the host to the excited states of impurities Tl^(+),Cu^(+),Mn^(2+), hybrid radiative states emerge at 2.95–3.15 eV, occupying the same energy levels as the intrinsic electronic trapping center SO_4^(3-) of the host at 2.95–3.1 eV.

Self-phase modulation (SPM) broadening of laser spectra was studied in a transmission mode in natural and synthetic diamonds at variable laser wavelengths (515 and 1030 nm), pulse energies and widths (0.3 - 12 ps, positively chirped pulses), providing their filamentary propagation. Besides the monotonous SPM broadening of the laser spectra versus pulse energy, more pronounced for the (sub)picosecond pulsewiths and more doped natural diamond, periodical low-frequency modulation was observed in the spectra at the shorter laser pulsewidths, indicating dynamic Bragg filtering of the supercontinuum due to ultrafast plasma and nanoplasmonic effects. Damping of broadening and ultramodulation for the longer picosecond pulsewidths was related to thermalized electron-hole plasma regime established for the laser pulsewidths longer, than 2 ps. Unexpectedly, at higher pulse energies and corresponding longer microfilaments, the number of spectral modulation features increases, indicating dynamic variation of the periods in the longitudinal plasma Bragg gratings along the filaments due to prompt secondary laser-plasmon interactions.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

MP2/aug-cc-pVTZ calculations were carried out for the ZFH₃-B complexes (Z = C, Si, Ge, Sn and Pb; B = C₂H₂, C₂H₄, C₆H₆ and C₅H₅^-; relativistic effects were taken into account for Ge, Sn and Pb elements). These calculations are supported by other approaches; the decomposition of the energy of interaction, Quantum Theory of Atoms in Molecules (QTAIM) and Natural Bond Orbital (NBO) method. The results show that tetrel bonds with π-electrons as Lewis bases are classified as Z…C links between single centers (C is an atom of the π-electron system) or as Z…π interactions where F-Z bond is directed to the mid-point (or nearly so) of the CC bond of the Lewis base. The analogues systems with Z…C/π interactions were found in the Cambridge Structural Database (CSD). It was found that the strength of interaction increases with the increase of the atomic number of the tetrel element and that for heavier tetrel elements the ZFH₃ tetrahedral structure is more deformed towards the structure with the planar ZH₃ fragment. The results of calculations show that the tetrel bond is sometimes accompanied by the Z-H…C hydrogen bond or even sometimes the ZFH₃-B complexes are linked only by the hydrogen bond interaction.

The apparent shape of the black hole shadow provides a full description of the spin, the inclination angle and the charge of a Kerr black hole, without any astrophysical process or underlying theory in the astrophysical process.

The thermodynamics of black holes is discussed for the case, when the Newton constant G is not a constant, but is the thermodynamic variable. This gives for the first law of the Schwarzschild black hole thermodynamics: d S BH = − A d K + d M T BH , where the gravitational coupling K = 1 / 4 G , M is the black hole mass, A is the area of horizon, and T BH is Hawking temperature. From this first law it follows that the dimensionless quantity M 2 / K is the adiabatic invariant, which in principle can be quantized if to follow the Bekenstein conjecture. From the Euclidean action for the black hole it follows that K and A serve as dynamically conjugate variables. This allows us to calculate the quantum tunneling from the black hole to the white hole, and determine the temperature and entropy of the white hole.

A dark region and a bright part of accretion disk are viewed on the first image of the supermassive black hole in the galaxy M87 obtained by the Event Horizon Telescope. We demonstrate that a viewed dark region is a silhouette of the black hole event horizon, while the outline (contour) of this silhouette is an equator of the event horizon globe. A dark silhouette of the black hole event horizon is placed within the expected position of the black hole shadow, which is not revealed on the first image. We calculate numerically a relation between the viewed position of the black hole silhouette and the brightest point in a thin accretion disk in dependence of the black hole spin. A spin of the supermassive black hole in the galaxy M87, derived from this relation, is $a=0.75\pm0.15$.

Natural Fibre Reinforced Composites (NFRCs) represent a significant category of materials that has the capacity to contribute to the worldwide objectives of sustainability and environmental preservation. To maximise the potential of composite materials, it is essential to establish their high quality and cost-effective manufacture. While the basic production procedures for producing items based on NFRCs have reached a high level of development, more research efforts are needed to advance their secondary manufacturing processes, namely in the areas of machining and joining. The primary factor leading to the rejection of composite goods with holes is the damage generated during the drilling process. The present experimental study aims to examine the effectiveness of hole production during the moulding phase. A comparative analysis has been conducted to assess the mechanical characteristics of moulded and drilled holes in jute fibre reinforced epoxy composite. It was observed that the moulded holes exhibit superior performance compared to the drilled holes for jute/epoxy materials. Additionally, the load extension curves indicate that the moulded holes experience greater extension in comparison to the drilled holes.

In this article, Planck star and remnant scenario i.e., solution of black hole information paradox in loop quantum gravity (LQG) are elaborated. Since, Black hole is the final fate of collapse scenario in general relativity; firstly, gravitational collapse with two possible final outcomes i.e., black hole and naked singularity, is outlined. Thereafter, black hole thermodynamics along with four laws of black hole thermodynamics, Hawking radiation, brief introduction to information theory and cause of information paradox are given. Then, solution of black hole information paradox outside the LQG are briefly explained. Thereafter, basic concepts of LQG along with loop quantum cosmology (LQC) are described. LQG can solve information paradox by its natural cut off on the value of quantum volume operator. In LQG, a star namely, Planck star is also proposed that is formed at Planck density and resides at so-called singularity point. Since, LQG removes singularity through big bounce and proposes Planck star which provides enough room for information to escape; hence, it can solve information paradox. LQG predicts remnant of black hole of the order of \(10^{-14} m\); which, is under current technological regime. In the remnant scenario, black hole makes quantum transition into white hole and this white hole behaves as a long lived remnants that can solve information paradox. In this quantum transition, a black hole tunnels into a white hole at the end of evaporation.

M87 is a giant elliptical galaxy in the Virgo cluster of galaxies. The radio source has a core which coincides with the nucleus of the galaxy and a jet of emission which is detected from radio to X-ray bands. A supermassive black hole is assumed to be at the centre of M87 which sends out relativistic particles in the form jets along its axis of rotation. Relativistic particles accelerated in a magnetic field, give out synchrotron radiation. The centre is surrounded by an accretion disc, which is the closest that we can probe into a black hole. High resolution observations are needed to examine the nature of the radio emission closest to the centre of M87. An array of millimetre-band telescopes across the globe were used as an interferometer, called the Event Horizon Telescope, (EHT) to probe the nuclear region. The angular resolution of this interferometer array is 25 microarc sec, at a wavelength of 1.3mm and the data was carefully calibrated and imaged. The resulting image shows an asymmetric ring which is consistent with the predictions of strong gravitational lensing of synchrotron emission from hot plasma near the event horizon. In this paper, we review the results of the observations of the radio galaxy, M87, using the Event Horizon Telescope

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

In this paper, we discuss optical properties of the topologically charged rotating black hole. We study the horizon, the photon region, the shadow of the black hole and other observables. The results show that in addition to the black hole spin parameter $a$, the other two parameters, five-dimensional mass parameter $\beta$ and electric charge $q$, are also found to affect the horzion, the photon region and the black hole shadow. In a certain range, with the increase of the three parameters, the horizon distance, shape of the photon region and the black hole shadow will all shrink. Moreover, with the increase of these three parameters, the distortion parameter $\delta_{s}$ gradually increases, while the peak of the black hole energy emission rate decreases.

The open hole tensile and flexural test of composites holds immense importance in aerospace and structural engineering. These tests provide critical insights into how composites perform under real-world conditions, allowing for the development of materials that meet rigorous standards, thereby ensuring the safety and durability of aircraft and other applications. This study investigates the influence of hole size on the open hole tensile (OHT) and flexural properties (OHF) of plane woven aramid/epoxy (AFRP), basalt/epoxy (BFRP), and aramid-basalt/epoxy (ABFRP) sandwiched laminates. Specimens with three different hole sizes viz., 4 mm, 6 mm, 8 mm were prepared and tested according to ASTM D5766 and ASTM D7264 for OHT and OHF performance respectively. Results indicated that the hybridization of aramid-basalt layers in a sandwich lay up significantly improved the mechanical performance when compared to only aramid laminate. However, with the increase in hole size the mechanical properties declined irrespective of the material. Basalt fibres showed higher hole sensitivity under tensile loading due to its brittle fracture mechanism while aramid fibres exhibited higher hole sensitivity under flexural loading which can be attributed to its the poor compressive strength. The effect of hole size on the damage mechanism has also been highlighted through scanning electron microscope (SEM). Major failure modes observed are delamination around the hole edges, ductile and brittle fibre fractures, and delamination.

A persistent idea in cosmology is that the universe originated and then continued to evolve as a black hole. While the notion of a black hole universe has generally been framed within the standard cosmological model, the latter has had numerous problems related to dark matter, dark energy and other issues. To avoid such problems an alternative is proposed which omits cosmic expansion, dark matter and dark energy. The observable universe is cast instead as primarily a thin spherical shell of cold (~29 K) baryonic matter situated near the Hubble radius. This shell of plasma holds 95% of the observable universe’s mass, the remaining 5% existing in the interior galaxies and gas clouds. A key premise of the model is that spacetime is fundamentally photonic in nature. This allows photon energy to be transferred to spacetime in the Hubble redshift and to be transferred back to photons in a novel blueshift. These exchanges together drive a cosmic energy cycle for gravity and the cosmological constant, Λ. Photons of the cosmic microwave background originating in the plasma shell lose energy to ‘cooler’ regions of spacetime in interior zones via the Hubble redshift. This gives rise to gravity through the optical gravity approach. The depleted photons moving back towards the shell are then reenergized in ‘hotter’ spacetime regions via the Hubble blueshift. These photons eventually exert outward pressures on the shell which perfectly balance the inward forces of gravity, in this manner functioning as Einstein’s cosmological constant. The observable universe behaves as a closed system in thermodynamic equilibrium with constant energy and entropy and indeterminate age. Black holes are suggested to have analogous plasma shell structures and gravity/Λ cycles.

Theoretical approaches to calculate pKa values for Brønsted acids is a challenging task that, most of the time, involves sophisticated and time-consuming methods. Therefore, heuristic approaches are efficient and appealing methodologies to approximate these values. Herein, by considering the electrostatic potential on acidic hydrogen atoms in a similar fashion that a σ–hole is defined, we calculated the maximum surface potential, V_S,max, and used it as a descriptor to correlate it with experimental acidity constants. These values were calculated using the CPCM implicit solvent model (water) with six different methods: five density functionals and the Møller–Plesset second order perturbation theory. Six different basis sets were combined with each method in order to benchmark a total of thirty-six levels of theory. Overall, 1080 calculations were performed and found to correlate with experimental data. The ωB97X-D/6-31+G(d,p) level of theory stands as the best one for consistently reproduce the reported pKa values.

A black hole in a Schwarzschild spacetime is considered. A transformation is proposed that describes the relationship between the coordinate systems exterior and interior to an event horizon. Application of this transformation permits considerations of the (a)symmetry of a range of phenomena taking place on both sides of the event horizon. The paper investigates two distinct problems of a uniformly accelerated particle. In one of these, although the equations of motion are the same in the regions on both sides, the solutions turn out to be very different. This manifests the differences of the properties of these two ranges.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

The sources of dark matter and its spatial distribution is not in the typical standard model. The study thought to induct the physical causalities with empirical evidence on the theory of black hole and white hole juxtapose. The research applied a mixed method of data analysis and observational cosmology. With the cosmological observations on the traces of white holes, the research finds that the accretion phenomenon of black holes is largely contributed by its thermonuclear binding with the white hole. The antimatter saturated plasma of cold fusion and hot fission are key to the phenomenon of black hole and white hole juxtapose. The force between the black hole and the white hole is stronger than the strong force, and sheds new directions on cosmological and gravitation studies. The research concludes that black holes are white hole entropy. The higher order of the universe in matter forms can exist beyond the observed force. The thermal arrow of time is critical to future general relativity dependent instrumentation discoveries.

Electroactive microorganisms have received a lot of interest in the field of environmental engineering and biotechnology because of their extracellular electron transfer (EET) capability of energy recovery and environmental remediation. However, the low efficiency of EET remains a barrier to its practical implementation. This review presents an introduction to EET, followed by addressing strategies for enhancing EET through different approaches including enhancing EET by mediator materials, external electricity, photo, and magnetism as well as integrated strategies, that is, the combination of multiple means to promote extracellular electron transport and improve the performance of microbial electrochemical systems. Finally, the challenges, perspectives, and new directions for EET enhancement will be discussed.

Scanning electron microscopy (SEM) is a powerful tool in the domain of material science, mining, and geology, owing to its enormous potential to provide unique insights into the micro and nanoscale worlds. This comprehensive review discusses the background development of SEM, basic SEM operation including the specimen preparation and imaging process, and fundamental theoretical calculations underlying the SEM operation. It provides foundational understanding to the engineers and scientists, who never got a chance to dig in-depth into the SEM, to understand the working and development of this robust analytical technique. The present review covers how SEM has been serving as a crucial tool in mineral characterization, with specific discussions on the working and research fronts of SEM-EDX, SEM-AM, SEM-MLA, and QEMSCAN. With automation gaining pace in the development of all spheres of technology, the understanding of uncertainties in SEM measurements is very important. The constraints in mineral phase identification by EDS spectra and sample preparation are conferred. In the end, future research directions for SEM are analyzed with the possible incorporation of machine learning, deep learning, and artificial intelligence tools, for automating the process of mineral identification, quantification, and efficient communication with the researchers, so that the analytical process robustness and objectivity can be improved, and the analysis time and the involved costs can be brought down. This review also discusses the idea of integrating robotics with SEM, to make the equipment portable, so that further mineral characterization insights can be gained not only on earth but also on other terrestrial grounds.

In this letter, instead of choosing the Einstein Rosen bridge between two black holes as in ER=EPR, we consider a wormhole between a black hole and a closed edge of the wormhole. We assume that information in a black hole travels through a wormhole, turns to mass (dark matter) in the closed region. This study is in contradiction with the existence of the white hole in our Universe. We replace the notion of the white hole with the massive closed region. We prove the metric of the closed region by the Hopf fibration, this new metric generalizes the $AdS_{5}$\ metric.

In this paper, we present a technique to unify the Reissner–Nordstr¨om metric and the Kerr–Newman metric. We construct a specifific model and calculate the entanglement entropy of black horizon. We are interested in the entangled particle and antiparticle spinning on the black hole horizon. The two Reissner-Nordstr¨om horizons r±, are the results of the rotation of several entangled particle-antiparticle on the real horizon. The energy absorbed by a black hole is transformed into a kinetic energy of the entangled particle-antiparticles. This study provides a new type of black hole metric. We show that the rotation of an entangled system of a particle and an antiparticle can create a extremal black hole. We also explore some of the implications of this point of view for the black hole entanglement.

In this work, we investigated whether the Pseudo-Newtonian theory (PNP) is applicable to black hole solution in modified gravity. In this regard, as an example, a static spherically symmetric 4D AdS Schwarzschild Yang-Mills black hole in EinsteinGauss-Bonnet gravity is considered. Also, a brief discussion on the structure and horizons of this black hole spacetime is presented. We calculated angular momentum and energy in the framework of the general theory of relativity as well as in PNP theory. In both of these framework, a graphical comparison of angular momentum has been studied

The invariant mass of free particles is used to derive a bound-state equation for several particle atomic systems at rest. This relativistic-kinematic bound-state equation is applied to the hydrogen and helium atoms. The derived equation has the well-known solutions for the single-electron bound states of the hydrogen atom, and the two-electron states of the helium atom. For the hydrogen atom, existence of the two-particle bound states, for which the electron and the proton kinetic energies are of the same order of magnitude, is predicted. The three-particle bound states with the same feature of the kinetic energies can exist in the helium atom. Radiative operators for processes involving the hydrogen two-particle bound states, are obtained. It is discussed that these new two- and three-particle bound states should be optically inactive.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

The [3+2] cycloaddition (32CA) reactions of strongly nucleophilic norbornadiene (NBD) with simplest diazoalkane (DAA) and three DAAs of increased electrophilicity have been studied within the Molecular Electron Density Theory (MEDT) at the MPWB1K/6-311G(d,p) computational level. These pmr-type 32CA reactions follow an asynchronous one-step mechanism with activation enthalpies ranging from 17.7 to 27.9 kcal·mol-1 in acetonitrile. The high exergonic character of these reactions makes them irreversible. The presence of electron-withdrawing (EW) substituents in the DAA increases the activation enthalpies, in complete agreement with the experimental slowing-down of the reactions, but contrary to the Conceptual DFT prediction. Despite the nucleophilic and electrophilic character of the reagents, the global electron density transfer at the TSs indicates rather non-polar 32CA reactions. The present MEDT study allows establishing that the depopulation of the NNC core in this series of DAAs with the increase of the EW character of the substituents present at the carbon center is responsible for the experimentally found deceleration.

In this paper, we propose an assumption of which the relation between electron and phonon is discussed and investigated based on the experiment of γ photon and electric interconverting with each other. We calculated the charge of a particular standing wave topology with Maxwell’s equation rotated in accordance space with the SO3 transformation. The derived charge value is 1.6035 × 10E−19C around 0.0826% different from the experimental data, indicating the proposal is a promising theory to explain the origin of charge and spin of electron particle. Electron spin angular momentum comes from the orbital angular momentum of photon rotation (electromagnetic field rotation), and electron charge comes from photon, that is, the space-time rotation effect of electromagnetic wave.

In 2011, by 1.3 mm wavelength VLBI radio wave observations of the SgrA*, Fish, V. L. et al showed that the emissions tightly related to the formation of a black hole shadow have a remarkably large time-varying feature within a region of less than 50 μas. The present paper suggests that the origin of the time variation in the observed emission is due to effects of the orbital motion of the existing super-massive black hole binary orbiting at SgrA* with a period of 2150±2.5 s. This suggestion is based on observations of decameter radio wave pulses from SgrA*. We show a good correlation between the time variation in the coherent flux density of the VLBI results and the time variation model of estimated emission intensities based on the periodic motion of the super-massive black hole binary by applying parameters deduced from the decameter radio wave pulse observation model (DRWP-Model). With further confirmation by Fourier analyses of the potential periodicity of the VLBI data that show the same periods of DRWP Model, we conclude that the time variation detected by the 1.3 mm wavelength radio wave VLBI is evidence of an existing super-massive black hole at Sgr A*.

The present study investigation, our results on characterization of commercially pure-Ti alloy brazed with metallic glass ribbons of Ti20Zr20Cu60-xNix (x = 30, 40, and 50) metallic glass ribbons were produced using a vacuum melt spinner. These ribbons were then used as filler materials for vacuum brazing of two Ti alloy plates at 1268, 1277 and 1279 K for a period of 10 min. Field-Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy (TEM) and the energy dispersive X-ray spectroscopy (EDX). The as-spun ribbons showed fully amorphous structure when examined on both surfaces by XRD and also verified by TEM investigation. The brazing joint of two Ti-plates using the metallic glass ribbon when brazed with Ni50 was found to be of very high strength. FESEM characterization of the cross-section of the brazed joints shows sub-micron size grains uniformly distributed in the matrix with brighter appearance. FESEM and EDX analysis revealed that the sub-micron grains are rich in Ti & Ni while the matrix phase mainly consisted of Ti. BSE image along with EDS Analysis indicated that the brazed joint has a presence of NiTi2 and Cu2 (Ni Zr) phases which could be responsible for increase in the strength of the brazed joint.

In recent years, drones have become increasingly prevalent in a wide range of applications, performing complex and critical tasks. To accomplish these tasks, drones cooperate by forming a Fly Ad-hoc Network (FANET) using specific routing protocols for communication. However, most of the routing protocols used in this type of network lack appropriate built-in security mechanisms, which creates numerous security challenges and concerns. To reduce the resulting security vulnerabilities and mitigate the impact of potential attacks, it is crucial to address these challenges before any deployment of FANETs. In this paper, we address two of the most harmful routing attacks - Sybil and Gray Hole and propose mitigating techniques to alleviate these attacks on FANET routing protocols. The proposed solution is secGPSR a secure version of the Greedy Perimeter Stateless Routing Protocol (GPSR). We validate the robustness of secGPSR through simulation using Omnet++ and present the results which show its effectiveness against Sybil and Gray Hole attacks.

We elucidate the versatility of intriguing symmetry and asymmetry phenomena outside and inside black holes. For description of the test particle (planet and photon) motion it is used the Kerr-Newman metric of the rotating and electrically charged black hole. In particular, it is demonstrated the symmetry and asymmetry of the one-way Einstein-Rosen bridge inside black hole toward and through the plethora of endless and infinite universes.

The aim of this review was to identify a new potential reason for the development of macular holes in relation to the female sex and to explain the possible underlying pathway. This approach was based on the evaluation of anatomical, physiological, and morphological analyses currently available in the literature. The findings showed that estrogen exerts a protective effect on the neuroretina. However, this protection may be lost by sudden decrease in estrogen levels during menopause. A gen analysis in zebra fish showed that estrogen may influence Müller and cone cells. Both cell types are responsible for the binding of the fovea structure. Cone implicit time in full-field 30-Hz flicker electroretinography is a predictor of visual outcome after surgery for macular hole. In conclusion, the fovea cone, through its sensibility to estrogen and high energy consumption, may be very vulnerable to damage caused by a sudden change in the concentration of estrogen in menopausal females. Such changes may result in cone degeneration and the development of a hole in the fovea, as in the case of macular holes. This review revealed that the cone under the decreasing influence of estrogen may play a key role with regards to the etiology of development of macular hole. This aspect may be of strategic importance in prophylactic therapy for the prevention of the development of macular hole in premenopausal females or after ocular trauma.

The paper proposes a theoretical study that investigates the quantum effects on the gravity of black holes. The study utilizes a gravitational model that incorporates quantum mechanics derived from the classical-like quantum hydrodynamic representation. The research calculates the mass density distribution of quantum black holes, specifically in the case of central symmetry. The gravity of the quantum black hole shows contributions coming from the quantum potential energy, which is also sensitive to the presence of the background of gravitational noise. The additional energy, stored in the quantum potential fluctuations and constituting a form of dark energy, leads to a repulsive gravity in the weak gravity limit. This repulsive gravity overcomes the attractive classical Newtonian force at large distances of order of the intergalactic length.

The plate embedded with acoustic black hole (ABH) indentations is potential for structural vibration and noise control. This work focuses on the mid- and low-frequency performance of plates embedded with the array of ABH for energy focalization and vibration & noise suppression. Plates embedded with two-dimensional ABHs are modelled with detailed Finite Element (FE) models, and the power flow method is introduced to analyze the energy propagation characteristics arising from ABH effect. Then the distribution of average vibration power density along ABH radius is studied. Next, the energy dissipation effects of the plate model embedded with ABH array with two types of damping layers are investigated. Finally, the sound pressure levels of the ABH structure are calculated and discussed. This work is helpful to understand the characteristics of plates embedded with ABH array in reducing vibration and noise radiation. Results show the tremendous potential of ABH array for vibration and noise control.

Astrophysical accretion processes near the black hole candidates, such as active galactic nuclei (AGN), X-ray binary (XRB), and other astrophysical sources, are associated with high-energetic emission of radiation of relativistic particles and outflows (winds and/or jets). It is widely believed that the magnetic field plays a very important role to explain such high energetic processes in the vicinity of those astrophysical sources. In the present research note, we propose that the black hole is embedded in an asymptotically uniform magnetic field. We investigate the dynamical motion of charged particles in the vicinity of a weakly magnetized black hole. We show that in the presence of the magnetic field, the radius of the innermost stable circular orbits (ISCO) for a charged particle is located close to the black hole’s horizon. The fundamental frequencies, such as Keplerian and epicyclic frequencies of the charged particle are split into two parts due to the magnetic field, as an analog of the Zeeman effect. The orbital velocity of the charged particle measured by a local observer has been computed in the presence of the external magnetic field. We also present an analytical expression for the four-acceleration of the charged particle orbiting around black holes. Finally, we determine the intensity of the radiating charged accelerating relativistic particle orbiting around the magnetized black hole.

A single tree topology is a commonly employed topology for wireless sensor networks (WSN) to connect sensors to one or more remote gateways. However, its many-to-one traffic routing pattern imposes heavy burden on downstream nodes, as the same routes are repeatedly used for packet transfer, from one or more upstream branches. The challenge is how to choose the most optimal routing paths that minimizes energy consumption across the entire network. This paper proposes a proactive energy awareness-based many-to-one traffic routing scheme to alleviate the above said problem referred to as Energy Balance-Based Energy Hole Alleviation in tree topology (EBEHA-T). This protocol combines updated status of variations in energy consumption pattern around sink-hole zones and distribution of joint nodes among the trees. With this approach, EBEHA-T proactively prevents sink-hole formation instead of just a reactive response after they have occurred. Performance evaluation of EBEHA-T against benchmark method RaSMaLai shows increased energy saving across the entire network and a marked improvement in energy consumption balance in energy-hole zones. This precludes energy hole formation and the consequent network partitioning, leading to improved network lifetime beyond that of the RasMaLai. OMNET++ network simulation software has been used for the evaluation.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electronical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

The dimethylaminophenyl-substituted silver phthalocyanine [dmaphPcAg] can be used as a UV-vis photoinitiator for in situ preparation of a silver/polymer nanocomposite. To verify early steps of the supposed mechanism of radical polymerization, we performed quantum chemical calculations of m[dmaphPcAg]q complexes with charges q = +1 to -2 in the two lowest spin states m, of a free ligand and its dehydrogenated/deprotonated products m[dmaphPcHn]q, n = 2 to 0, q= 0, -1 or -2, in the lowest spin states m. The calculated electronic structures and electron transitions of all the optimized structures in CHCl3 solutions are compared with experimental EPR and UV-vis spectra, respectively. The unstable 3[dmaphPcAg]+ species deduced only from previous EPR spin trap experiments was identified. In addition to 2[dmaphPcAg]0, our results suggest the coexistence of both reaction intermediates 1[dmaphPcAg]- and 3[dmaphPcAg]- in reaction solutions. Silver nanoparticle formation is a weak point of the supposed reaction mechanism from the energetic, stereochemistry, and electronic structure points of view.

Over the past two decades, covalent organic frameworks (COFs) have become the most widely studied porous crystalline materials. Its specific physical and chemical properties are determined by the arrangement of atoms (crystal structure). Therefore, the determination of its structure is arguably the most important characterization step for COFs. Although single crystal X-ray diffraction (SCXRD) is the most widely used method for structure determination, the size of COF crystals is too small, or their crystal quality is so poor that confirmation of their structure is limited to lattice fringes by transmission electron microscopy (TEM). At present, many 2D-COFs have clear PXRD patterns, but not all 2D-COFs can obtain specific lattice fringes. This severely hinders the development of the COF field. Here, we discover the lattice shrinkage behavior of COFs under electron beam irradiation by comparing the lattice fringes of 2D-COFs under different conditions. By comparing the lattice fringes of TAPT-TFPT COF at room temperature and under liquid nitrogen freezing conditions, we found that the lattice fringes are in good agreement with the Powder X-ray diffraction (PXRD) and theoretical values of COF (2.213 nm) under freezing conditions, however, the lattice fringe spacing is only 1.656 nm at room temperature. The discovery not only provides new insights into the TEM characterization of COFs, but also further expands the range of crystalline COF materials.

Multipactor is a common discharge phenomenon occurred in space microwave systems. The surface microstructure has been verified to be effective to mitigate multipactor. In this work, we design a square coaxial low-pass filter (SCLPF) with dielectric sheets loaded to check the multipactor dependence on the structure parameters of the loaded dielectric sheets, and further model groove structures on the sensitive area surface to lower the risk of multipactor. Simulation results indicate that the SCLPF loaded with alumina and PTFE exhibits good operational characteristics, and the multipactor threshold is significantly improved after introducing the surface grooves. Then we investigate the effects of three typical groove parameters, groove depth, groove number, and aspect ratio, on the multipactor threshold of the SCLPF device. The results show that the multipactor threshold raise at first as the groove number and groove depth increase, and then the threshold reaches a saturation status. For a deeper analysis of multipactor, we discuss how the grooves shelter the secondary electrons, and further mitigate the electron avalanche. Furthermore, the mechanisms of threshold saturation under the effect of groove parameters are analyzed in detail, and a contour map for the multipactor threshold of PTFE-loaded SCLPFs is given, which makes significant sense for predicting the multipactor threshold of the devices with its sensitive surface being grooved. The regularity of modulating the multipactor threshold by the groove structures obtained in this study is of engineering significance for suppressing multipactor in microwave devices in practical applications.

Sub-micro dislocation cellular structures formed during rapid solidification break the strength-ductility trade-off in laser powder bed fusion (LPBF)-processed 316L stainless steel through high-density dislocations and segregated elements or precipitates at the cellular boundaries. The high-density dislocation entangled at the cellular boundary accommodates solidification strains among the cellular structures and cooling stresses through elastoplastic deformation. Columnar grains with cellular structures typically form along the direction of thermal flux. However, the ultra-low misorientations between the adjacent cellular structures and their interactions with the cellular boundary formation remain unclear. In this study, we revealed the ultra-low misorientations between the cellular structures in LPBF-processed 316L stainless steel using conventional electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), and transmission electron microscopy (TEM). The conventional EBSD and TKD analysis results could provide the misorientation angles smaller than 2° while the resolution mainly depends on the specimen quality and scanning step size, and so on. TEM technique with higher spatial resolution provides accurate information between adjacent dislocation cells with misorientation angles smaller than 1°. This study presents that TEM method is the better and more precise analysis method of the misorientation measurement of the cellular structures and provides insights into measuring the small misorientation angles between adjacent dislocation cells and nanograins in nanostructured-metals and alloys with ultrafine-grained microstructures.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

In the perspective of designing complex concentrated alloys (CCAs) for structural applications, sigma (σ) phase is important. It is generally known to be an embrittling phase leading to a degradation in the mechanical properties of CCAs. This necessitates detailed investigations on the evolution of σ phase in these alloys. In the present study, an equiatomic CoCrCuMnNi CCA is chosen, in which σ phase appears at 800°C, as reported in a recent publication [1]. To this end, the present investigation aims at understanding the evolution of this phase so that its presence can be controlled for the purpose of preventing degradation in mechanical properties. In the present work, a vacuum arc melted alloy, after homogenisation (at 400°C for 5h), is heat-treated for different times ranging from 1 to 9h at 800°C followed by water quenching. Extensive characterisation has been carried out using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) techniques to understand the sequence of σ phase precipitation at 800°C.

In the Standard Model of elementary particles, the rest mass, magnetic moment and electric charge of the electron are considered to be natural constants. In this article it is proposed that these properties can be calculated in a simple way from the corresponding Planck units using the well-known period doubling phenomenon in nonlinear dynamical systems. Periods corresponding to the values of the electron and positron properties belong to a subset of stable periods. The periodic structures of the rest energy and magnetic moment consist of three internal degrees of freedom, whereas the Coulomb energy of the electric charge consists of four. The number of period doublings for the elementary charge determines the value of the fine structure constant alpha.

Aluminum alloy (Al6061) sheet micro-hole processing is extensively used in smartphones, tablet PC, and smart wearable devices. The micro-hole processing is commonly performed using laser, micro drilling, microstamping, micro discharge, and chemical etching technologies. Micro-stamping technology is characterized by precision and rapid processing, but the precision positioning of the punch head and lower die is one of the major difficulties in micro-hole stamping, especially in manufacturing array micro-holes. This study used stamping without die technology. This technology uses an array punch head to punch the lower die holes on the base, then performs array micro-hole stamping. The experimental results show that a micro-hole array with 37 micro-holes were successfully manufactured and can be reproduced many times. Tapered array micro-holes with a high aspect ratio can be manufactured using this stamping without die technology; the micro-hole depth can be 260μm, the inlet diameter is 116μm, and the outlet diameter is 25μm. This study has successfully developed the feasibility of array micro-hole stamping technology.

In a series of recent works the relevance of gravitational boundary degrees of freedom and their dynamics in gravity quantization and black hole information has been explored. In this work we further the progress by keenly focusing on the boundary degrees of freedom as the origin of black hole entropy. Wald's entropy formula is scrutinized, and the reason that the Wald's formula correctly captures the entropy of a black hole is examined. Afterwards, limitations of the Wald's method are discussed; a coherent view of entropy based on boundary dynamics is presented. The discrepancy observed in the literature between holographic and Wald's entropies is addressed. We generalize the entropy definition so as to handle a time-dependent black hole. Large gauge symmetry plays a pivotal role. Non-Dirichlet boundary conditions and gravitational analogues of Coleman-De Luccia bounce solutions are central in identifying the microstates and differentiating the origins of entropies associated with different classes of solutions. The result in the present work leads to a view that black hole entropy is entanglement entropy in a thermodynamic setup.

The classical uncertainty principle inequalities were imposed as a mathematical constraint over the general relativity geodesic equation. In this way, the uncertainty principle was reformulated in terms of the proper space-time length element, Planck length and a geodesic-derived scalar, leading to a geometric expression for the uncertainty principle (GeUP). This re-formulation confirmed the necessity for a minimum length for the space-time line element in the geodesic, dependent on a geodesic-derived scalar which made the expression Lorentz-covariant. In agreement with quantum gravity theories, GeUP required the imposition of a perturbation over the background Minkowski metric unrelated to classical gravity. When applied to the Schwarzschild metric, a geodesic exclusion zone was found around the singularity where uncertainty in space-time diverged to infinity.

The Einstein-Lovelock theory contains an infinite series of corrections to the Einstein term with an increasing power of the curvature. It is well-known that for large black holes the lowest (Gauss-Bonnet) term is the dominant one, while for smaller black holes higher curvature corrections become important. We will show that if one is limited by positive values of the coupling constants, then the dynamical instability of black holes serves as an effective cut-off of influence of higher curvature corrections in the 4D Einstein-Lovelock approach: the higher is the order of the Lovelock term, the smaller is the maximal value of the coupling constant allowing for stability, so that effectively only a first few orders can deform the observable values seemingly. For negative values of coupling constants this is not so, and, despite some suppression of higher order terms also occurs due to the decreasing threshold values of the coupling constant, this does not lead to an noticeable opportunity to neglect higher order corrections. In the case a lot of orders of Lovelock theory are taken into account, so that the black-hole solution depends on a great number of coupling constants, we propose a compact description of it in terms of only two or three parameters encoding all the observable values.

A thin-shell wormhole is crafted by the cut-and-paste method of two Bardeen de-Sitter black holes using Darmois-Israel formalism. Energy conditions are considered for different values of magnetic charge while both mass and cosmological constant are fixed. The attractive and repulsive characteristics of the throat of the thin-shell wormhole are also examined through the radial acceleration. Dynamics and stability of the wormhole are studied around the static solutions of the linearized radial perturbations at the throat of the wormhole. The regions of stability are determined by checking out the condition of concavity of the potential as a function in the throat radius for different values of magnetic charges.

The effect of divergence of chute sidewalls with three different baffle block geometries namely USBR, trihedral and semicircular blocks, as well as the depth and dimensions of the scour hole downstream of the chute were studied using a physical model. For this purpose, 9 models of baffled chutes were designed and constructed with divergence ratios of 1.45, 1.75, and 2.45 and without divergence (with a divergence ratio of 1). Comparing the results on the effect of block geometry at different divergence ratios revealed that the use of blocks proposed in this study instead of standard USBR blocks reduced the mean and maximum scour hole by 50%. For a given block geometry, the mean depth, maximum depth, and length of scour hole were reduced by 75%, 58%, and 50%, respectively.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

Abstract: Scavenging of electrogenerated superoxide radical anion (O2•−) by pyrogallol (PyH3) was investigated on the basis of cyclic voltammetry and in situ electrolytic electron spin resonance spectrum in N,N-dimethylformamide with the aid of density functional theory (DFT) calculations. Quasi-reversible dioxygen/O2•− redox coupe was modified by the presence of PyH3, suggesting that O2•− was scavenged by PyH3 through proton-coupled electron transfer (PCET) involving two proton transfer and one electron transfer. The DFT calculation suggested that the formation of hydrogen bond (HB) complex and the subsequent concerted-two-proton coupled electron transfer (2PCET) characterized by catechol moiety in PyH3 is plausible mechanism which embodies the superior kinetics of the O2•− scavenging by PyH3 as shown in the electrochemical results. Furthermore, it was clarified that three hydroxyl groups of PyH3 promote the formation of prereactive HB complex, in comparative analyses using related compounds, resulting the promotion of the O2•− scavenging.

Abstract: Elimination of superoxide radical anion (O2•−) by tocopherols (TOH), and related compounds was investigated on the basis of cyclic voltammetry and in situ electrolytic electron spin resonance spectral measurements in N,N-dimethylformamide (DMF) with the aid of density functional theory (DFT) calculations. Quasi-reversible O2/O2•− redox was modified by the presence of TOHs, suggesting that the electrogenerated O2•− was eliminated by α-, β-, γ-TOH through proton-coupled electron transfer (PCET), but not by δ-TOH. The structure–activity correlation of α-, β-, γ-, and δ-TOH characterized by methyl group on the 6-chromanol ring was experimentally confirmed, where the methyl group promotes the PCET mechanism. Furthermore, comparative analyses using some related chemical analogues suggested that methoxyl group of the 6-chromanol ring is required for a successful electron transfer (ET) to O2•− through the PCET. The electrochemical and DFT results in dehydrated DMF suggested that the PCET mechanism involves preceding proton transfer (PT) forming hydroperoxyl radical followed by a concerted PCET (ET–PT). The O2•− elimination by TOH proceeds efficiently along the net PCET mechanism involving one ET and two PTs.

The intramolecular ionic Diel-Alder (IIDA) reactions of two dieniminiums have been studied within the Molecular Electron Density Theory (MEDT) at the B97XD/6-311G(d,p) computational level. ELF topological analysis of dieniminiums shows that its electronic structure can been seen as the sum of those of butadiene and ethaniminium. The superelectrophilic character of dieniminiums accounts for the high intramolecular global electron density transfer taking place between the diene and iminium frameworks at the transition state structures (TSs) of these IIDA reactions. The activation enthalpy associated to the IIDA reaction of the experimental dieniminium, 8.7 kcal·mol-1, is closer to that of the ionic Diels-Alder (I-DA) reaction between butadiene and ethaniminium, 9.3 kcal·mol-1. However, the activation Gibbs free energy of the IIDA reaction is 12.7 kcal·mol-1 lower than that of the intermolecular I-DA reaction. The strong exergonic character of the IIDA reaction, higher than 17 kcal·mol-1, makes the reaction irreversible. These IIDA reactions present a total re/exo and si/endo diastereoselectivity, which is controlled by the most favourable chair conformation of the tetramethylene chain. Electron localization function (ELF) topological analysis of the single bond formation indicates that these IIDA reactions take place through a non-concerted two-stage one-step mechanism. Finally, ELF and atoms-in-molecules (AIM) topological analyses of the TS associated to inter and intramolecular processes show the great similitude among them.

The elimination of superoxide radical anions (O2•−) by 5-amino-2-hydroxybenzoic acid (mesalazine, 5-ASA), 4-amino-2-hydroxybenzoic acid (4-ASA), and related compounds used for ulcerative colitis treatment was investigated using cyclic voltammetry and electron spin resonance (ESR) analyses aided by density functional theory (DFT) calculations. Quasi-reversible O2/O2•− redox was found to be modified by the compounds, suggesting that an acid-base reaction in which a hydroperoxyl radical (HO2•) is formed from O2•− occurs. However, the deprotonated 5-ASA anion can eliminate O2•− through proton-coupled electron transfer (PCET), forming a radical product. This electron transfer (ET) was confirmed by ESR analysis. The 4-aminophenol moiety in 5-ASA plays an important role in the PCET involving two proton transfers and one ET based on -conjugation. The electrochemical and DFT results indicated that O2•− elimination by 5-ASA proceeds efficiently viathrough the PCET mechanism after deprotonation of the 1-carboxyl group. Thus, 5-ASA may act as an anti-inflammatory agent in the alkali intestine through PCET-based O2•− elimination.

We introduce a device for automatic detection and reporting of crawling insects in urban environments. It is a monitoring device for urban pests that complies with the context of smart homes, smart cities and is compatible with the emerging discipline of the Internet of Things (IoT). We believe it can find its place to every room of a hotel, hospital, military camp and residence. This box-shaped device attracts targeted insect pests, senses the entering insect and takes automatically a picture of the internal space of the box. The picture is communicated through the Wi-Fi commonly found in such establishments to an authorized person/stakeholder receiving the picture to take proper action. The e-trap includes strong attractants (pheromone and/or food) to increase capture efficiency. The insect is trapped on the sticky floor of the device. The device carries the necessary optoelectronic sensors to guard all entrances of the trap. As the insect enters it interrupts the infrared light source. This triggers a detection event; a picture is taken, and a time-stamp is set before reporting the event through the Wi-Fi. The device can be integrated seamlessly in urban environments and operates unobtrusively to human activities. We report results on various insect pests and depending on the insect species, can reach a detection accuracy ranging from 96-99%.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

As sessile organisms, plants face a wide range of abiotic stresses, with salinity being a prominent constraint affecting their growth, development, and productivity, particularly in arid and semi-arid regions. This study focused on understanding how salinity impacts Jatropha curcas, an important oilseed plant for biodiesel production. By examining the anatomy and ultrastructure of stomata and chloroplasts, we investigated the effects of prolonged salinity stress on J. curcas. This stress led to changes in stomatal density, stomatal index, and ostiole aperture, which case an imbalance of water conductivity in the xylem. Through transmission electron microscopy, we explored the subcellular organization of J. curcas chloroplasts and their contribution to plant photosynthetic efficiency, providing insights into their role in this process. Notably, salinity treatment resulted in a significant increase in starch granules accumulation, leading to impaired the granal and stromal grana lamellae, destroying this ultrastructure. Our findings indicate that the anatomy and ultrastructure of chloroplasts play a crucial role in influencing photosynthetic efficiency and hydraulic conductivity. This study offers new perspectives on the structure and function of chloroplasts in J. curcas, presenting innovative opportunities to develop strategies that enhance biofuel production in areas with high soil salinity.

The ionic Diels-Alder (I-DA) reactions of a series of six iminium cations with cyclopentadiene have been studied within the Molecular Electron Density Theory (MEDT). The superelectrophilic character of iminium cations,  > 8.20 eV, accounts for the high reactivity of these species participating in I-DA reactions. The activation energies are found between 13 and 20 kcal·mol-1 lower in energy than those associated to the corresponding Diels-Alder (DA) reactions of neutral imines. These reactions are low endo selective as a consequence of the cationic character of the TSs, but highly regioselective. Solvents have poor effects on the relative energies, and an unappreciable effect in the geometries. In dichloromethane the activation energies increase slightly as a consequence of the better solvation of the iminium cations than the cationic TSs. ELF topological analysis of the bonding changes along the I-DA reactions shows that they are very similar to those in polar DA reactions. The present MEDT study makes it possible establishing that the global electron density transfer (GEDT) taking place at the TSs of I-DA reactions, and not steric (Pauli) repulsions such as have been recently proposed, are responsible for the features of these type of DA reactions.

We study the problem of a spherically-symmetric distribution of a perfect relativistic fluid accreting onto a (potentially spinning) black hole within a fully discrete spacetime setting. This problem has previously been studied extensively in the context of continuum spacetimes, beginning with the purely analytic work of Bondi in the spherically-symmetric Newtonian case, Michel in the spherically-symmetric general relativistic case, and Petrich, Shapiro and Teukolsky in the axially-symmetric general relativistic case relevant for spinning black holes. However, the purpose of the present work is to determine the effect of discretization of the underlying spacetime upon the mass/energy and momentum accretion rates, the overall morphology and characteristics of the accretion flow, and the drag force exerted on the black hole in the case of non-zero spin. In order to achieve this, we first develop a novel formulation of the equations of general relativistic hydrodynamics that is more directly amenable to rigorous analysis within a discrete spacetime setting, and we then proceed to implement this formulation into the \textsc{Gravitas} computational general relativity framework. Through a combination of mathematical analysis and explicit numerical simulation in \textsc{Gravitas}, we discover that the mass/energy and momentum accretion rates both decrease monotonically as functions of the underlying spacetime discretization scale, with this effect becoming more pronounced for higher values of the black hole spin parameter, higher fluid temperatures, and stiffer equation of state parameters. We also find that the exerted drag force is highly sensitive to the value of the underlying discretization scale in the case of spinning black hole spacetimes, with certain instabilities becoming significantly more pronounced at certain critical values of the discretization parameter. We discuss some potentially observable consequences of these results, as well as some directions for future theoretical investigation.

In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

Study of perihelion shift of Mercury and deflection angle are important aspects for the verification of general relativity. For Schwarzschild geometry both the perihelion shift and weak deflection angle were independent of charge whereas for ReissnerNordstrom space-time charge should effect on both the perihelion shift and deflection angle. This paper shows the perihelion shift decreases with the increases of charge. Effect of other parameters like angular momentum, mass parameter, distance of closest approach on perihelion precession and deflection angle has also discussed. This paper also includes the graphical behavior which verifes our theoretical calculations.

When an edge is removed, a cycle graph Cn becomes a n-1 tree graph. This observation from extremal set theory leads us to the realm of set theory, in which a topological manifold of genus-1 turns out to be of genus-0. Starting from these premises, we prove a theorem suggesting that a manifold with disjoint points must be of genus-0, while a manifold of genus-1 cannot encompass disjoint points.

Various techniques to tackle the black hole information paradox have been proposed. A new way out to tackle the paradox is via the use of pseudo-density operator. This approach has successfully dealt the problem with a two-qubit entangle system for a single black hole. In this paper, we present the interaction with a binary black hole system by using an arrangement of the three-qubit system of Greenberger–Horne–Zeilinger (GHZ) state. We show that our results are in excellent agreement with the theoretical value. We have also studied the interaction between the two black holes by considering the correlation between the qubits in the binary black hole system. The results depict a complete agreement with the proposed model. In addition to the verification, we also propose how modern detection of gravitational waves can be used on our optical setup as an input source, thus bridging the gap with the gravitational wave’s observational resources in terms of studying black hole properties with respect to quantum information and entanglement.

We use a random gap model to describe a metal-insulator transition in three-dimensional semiconductors due to doping and find a conventional phase transition, where the effective scattering rate is the order parameter. Spontaneous symmetry breaking results in metallic behavior, whereas the insulating regime is characterized by the absence of spontaneous symmetry breaking. The transition is continuous for the average conductivity with critical exponent equal to 1. Away from the critical point the exponent is roughly 0.6, which may explain experimental observations of a crossover of the exponent from 1 to 0.5 by going away from the critical point.

The electronic structure and the participation of the simplest azomethine imine (AI) in [3+2] cycloaddition (32CA) reactions have been analysed within the Molecular Electron Density Theory (MEDT) using DFT calculations at the MPWB1K/6-311G(d) level. Electron localisation function (ELF) topological analysis reveals that AI has a pseudoradical structure, while the conceptual DFT reactivity indices characterise this TAC as a moderate electrophile and a good nucleophile. The non-polar 32CA reaction of AI with ethylene takes place through a one-step mechanism with low activation energy, 5.3 kcal/mol-1. A bonding evolution theory (BET) study indicates that this reaction takes place through a non-concerted [2n+2τ] mechanism in which the C–C bond formation is clearly anticipated prior to the C–N one. On the other hand, the polar 32CA reaction of AI with dicyanoethylene takes place through a two-stage one-step mechanism. Now, the more favourable regioisomeric transition state structure (TS) is located 8.5 kcal•mol⁻¹ below the reagents, in complete agreement with the high polar character of the TS. The current MEDT study makes it possible to extend Domingo’s classification of 32CA reactions to a new pra-type of reactivity.

Friction and wear take place on two solid surfaces in sliding contact as a result of the mechanical, thermal and chemical interactions with the participation of environmental species. Electron microscopy and the associated spectroscopic analyses are powerful in probing these mechanisms in spatial resolutions from micro to atomic scale. This article provides a review of the author’s work in the wear and friction mechanisms of PVD hard coatings in which various SEM- and TEM-based microscopic and spectroscopic techniques were employed. Understanding on the failure mechanisms and the origin of self-adaptive friction has been improved to nano-scale. Other related issues are also discussed, such as sample preparation techniques for cross-sectional electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy.

Black hole temperature T_BH = T_P/2πd as a function of its Planck length real diameter multiplier d is derived from black hole surface gravity and Hawking temperature w.l.o.g. It is conjectured d = 1/2π describes primordial Big Bang singularity as in this case T_BH = T_P. A black hole interacts with the environment and observable black holes have uniquely defined Delaunay triangulations with a natural number of spherical triangles having Planck areas (bits), where a Planck triangle is active and has gravitational potential of -c² if all its vertices have black hole gravitational potential of -c²/2 and is inactive otherwise. As temporary distribution of active triangles on an event horizon tends to maximize Shannon entropy a black hole is a fundamental, one-sided thermodynamic equilibrium limit for a dissipative structure. Black hole blackbody radiation, informational capacity fluctuations, and quantum statistics are discussed. On the basis of the latter, wavelength bounds for BE, MB, and FD statistics are derived as a function of the diameter multiplier d. It is shown that black holes feature wave-particle duality only if d ≤ 8π, which also sets the maximum diameter of a totally collapsible black hole. This outlines the program for research of other nature phenomena that emit perfect blackbody radiation, such as neutron stars and white dwarfs.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

It has been recently demonstrated that inelastic helium-atom scattering from conducting surfaces can provide a direct measurement of the surface electron-phonon coupling constant (mass-enhancement factor ) via the temperature- or the incident-energy-dependence of the Debye-Waller exponent. The analysis of previous published as well as unpublished helium atom scattering diffraction data from the vicinal surfaces of copper (Cu(11),  = 3,5,7) and aluminium (Al(221) and Al(332)) permits to extract  for this class of surfaces, suggesting an enhancement with respect to the corresponding data for the low-index surfaces (111) and (001) above a possible roughening transition temperature. The specific role of steps as compared to that of terraces is briefly discussed.

Our knowledge of electricity is based on two parallel lines of research: one focusing on ‘charge’, the other on ‘electron’. The distinction is blurred. The difficulty is that the fundamental nature of elementary charge is unknown. Here I present evidence that charge is a resting electron and electron is a moving charge – one physical entity two behavioural identities. That is, charge is nonrelativistic electron and electron is relativistic charge. Charges obey the laws of static electricity (electrostatics); electrons obey the laws of moving electricity (electrodynamics). Whether positive or negative, a charge is ejected from the atom at tremendous speed, losing the characteristics of ‘a charge’ and gaining those of ‘an electron’. I conclude that an atom, hence nature in general, contains an equal number of positive and negative electrons, recognised at rest as opposite charges. This solves the mystery of the electron-positron numerical asymmetry. It means that static positions and negatrons (charges) play equivalent roles as subatomic building blocks of matter, revealing a new atomic structure.

I demonstrate that the macrocosmic gravitational interaction between two masses and the microcosmic electrostatic interaction between two charges unify in simple concepts and mathematical laws when electric charge and ordinary mass are interpreted in reciprocal terms. No previous research has ever attempted to unify charge and mass. The difficulty has been lack of an intelligible definition of charge. A three-point paradigm shift solves the problem, giving convincing evidence – for the first time – that positron and negatron are the ultimate elementary particles. That is, matter is pure positive and negative grains of electricity. Paradigm shift #1: Electron is a moving charge; a charge is static electron – ‘one entity two identities’. This implies that ordinary matter contains equal numbers of positive and negative electrons – observed in motion as ‘electrons’ and at rest as ‘charges’. In motion, a positron-negatron pair obeys the laws of electrodynamics and annihilates; at rest, the pair obeys the laws of electrostatics and neutralizes. Paradigm shift #2: Electron mass and electrostatic field are either positive or negative. Opposite masses and fields, rather than indefinable ‘charge’, make opposite electrons physically different. Paradigm shift #3: Electric charge and ordinary mass interconvert. Positive charge (e⁺) and negative charge (e^-) neutralize to neutral charge (2e⁰), which is nature’s quantum of ordinary mass. Conversely, a quantum of ordinary mass splits to opposite charges e.g. in frictional electrification. The insights systematize the search, identification and classification of ‘elementary particles’, ending decades of confusion in the ‘elementary particle zoo’. They identify a new, stable subatomic particle – a third nucleon.

In the succinic acid-producing bacterium Pseudoclostridium thermosuccinogenes the fumarate reductase (FRD) genes reside in an operon together with those encoding an electron bifurcating complex (FlxABCD-HdrABC) that shuttles electrons from NADH to ferredoxin and a disulfide bond. Based on phylogeny and genomic co-occurrence we propose two hypothetical mechanisms via which the FRD is involved in electron bifurcation: (I) A disulfide bond from a hitherto unknown cofactor is reduced by the electron-bifurcating FlxABCD-HdrABC complex, using NADH to generate two thiol groups, while facilitating the unfavourable reduction of ferredoxin by NADH. The disulfide bond is subsequently regenerated via the reduction of fumarate by the FRD using the previously formed thiol groups. (II) The FRD forms an integral part of the FlxABCD-HdrABC complex, and NADH is used to reduce ferredoxin and fumarate directly, without an intermediate disulfide-forming cofactor. Either way enables the conservation of additional energy by a soluble FRD, analogous to fumarate respiration.

Background/Aim: There is continuing interest in engineering esthetic labial archwires. The aim of this study was to coat nickel-titanium (NiTi) and beta-titanium (β-Ti), also known as titanium molybdenum (TMA), archwires by plasma electrolytic oxidation (PEO) and to analyze the characteristics of the PEO-surfaces. Materials and Methods: PEO-coatings were generated on 0.014-inch NiTi and 0.19x0.25-inch β-Ti archwires. The surfaces were analyzed by scanning electron microscopy and stereomicroscopy. Cytocombability testing was performed with ceramized and untreated samples according to EN ISO 10993-5 in XTT-, BrdU- and LDH-assays. The direct cell impact was analyzed using LIVE-/DEAD-staining. In addition, the archwires were inserted in an orthodontic model and photographs were taken before and after insertion. Results: The PEO coatings were 15 to 20 µm thick and esthetically pleasing. The cytocompatibility analysis revealed good cytocompatibility results for both ceramized NiTi and β-Ti archwires. In the direct cell tests, the ceramized samples showed improved compatibility as compared to those of uncoated samples. However, bending of the archwires resulted in loss of the PEO-surfaces. Nevertheless, it was possible to insert the β-Ti PEO-coated archwire in an orthodontic model without loss of the PEO-ceramic. Conclusion: PEO is a promising technique for the generation of esthetic orthodontic archwires. Since the PEO-coating does not resist bending, its clinical use seems to be limited so far to orthodontic techniques using straight or pre-bended archwires.

Bitumen aging is the major factor which contributes to the deterioration of the road pavement. Oxidation and volatilization are generally considered as the most important phenomena affecting aging in asphalt paving mixtures. The present study was carried to investigate whether various antioxidants provided by natural resources such as phospholipids, ascorbic acid as well as lignin from rice husk, could be used to reduce age hardening in asphalt binders. A selected bituminous material was modified by adding 2 % w/w of the anti-aging natural additives and subjected to accelerated oxidative aging regimes according to the Rolling Thin Film Oven Test (RTFOT) method. The effects of aging were evaluated based on changes in sol-gel transition temperature of modified bitumens measured through Dynamic Shear Rheology (DSR). Moreover, changes of Electron Paramagnetic Resonance (EPR) spectra were monitored on the bituminous fractions asphaltene and maltene separated by solvent extraction upon oxidative aging. The phospholipids-treated binder exhibited the highest resistance to oxidation and the lowest age-hardening effect compared to the other tested anti-oxidants. The combination of EPR and DSR techniques represents a promising method for elucidating the changes in associated complex properties of bitumen fractions promoted by addition of free radical scavengers borrowed by green resources.

X-ray crystallographic and theoretical charge density data for a series of compounds [(Co(Ts3tren))M(Co(Ts3tren))] (M = Mg, Ca, Sr and Ba) is examined. The crystal structures are isostructural and the alkaline earth metal ions have the same arrangement of donor oxygen atoms despite the large variation in ionic radii. The isomorphism of these molecules is surprising and a theoretical examination of the electronic structures, with the different metal ions along the series, provides detailed insight into their stabilities. The theoretical and experimental data are consistent and agree well. The local properties of the Co(II) ion and its donor atoms are relatively independent of the alkali earth metal.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

We considered the hypothesis that the sources of dark energy (DE) could be black holes (BHs) or more exotic objects, such as naked singularities or gravastars. We proposed a definition of the presence of DE in the Universe and a criterion for what can be considered the source of this dark energy. It is based on the idea of the accelerated expansion of the Universe, which requires antigravity caused by large negative pressure. A recently proposed hypothesis was examined that mass of BHs increases with time according to the same law as the volume of the part of the Universe containing it and the population of BHs can mimic DE. We demonstrate the reasons why it cannot be accepted, even if all the assumptions on which this hypothesis is based are considered true.

We use the Stefan-Boltzmann law to derive and investigate what we will call the black hole CMB temperature luminosity. Interestingly, the CMB luminosity is always the same for every black hole at a luminosity distance equal to the Schwarzschild radius, which is fully valid in black hole cosmology, a topic that is actively discussed to this day. The CMB black hole luminosity is always the same , regardless of the mass of the black hole. This is in contrast to the Bekenstein-Hawking luminosity, which is linked to the Hawking temperature, that is mass dependent.

With the rapid development of China's economy, construction industrialization has become the main development trend of China's construction industry, and the convenient, efficient, environmental protection has become the new fashion, therefore the application of prefabricated building is more and more common. Stair serves as the weak link in prefab type building, the connecting node has an important influence on its failure. In this paper, pseudo-static tests are carried out on the joints in different forms of ladder holes to study the mechanical properties of flexible hinge points filled with flexible materials, and the hysteresis curve, skeleton curve and bearing capacity of each specimen are analyzed. The test results show that the flexible hinge can give full play to its flexible characteristics to ease the stress of ladder beam, pin bolt reinforcement and ladder hole, and the bearing capacity of flexible hinge points is moderate, which can not only mitigate the inclined bracing effect under the action of small and medium earthquakes, but also ensure the stair does not fall off under the action of large earthquakes. Through the experiment comparison, the ladder hole adopts node form 2, which can give full play to the advantage of flexible material.

China is rich in coal resources, but the complex hydrogeological conditions lead to difficulties in coal mining, such as coal mine collapse, roof and water damage, and other accidents that occur frequently, resulting in many casualties and property losses. The use of coal mine hole detection technology to detect and analyze the internal environment of the coal mine in advance helps to reduce safety hazards and prevent coal mine accidents, for the existing coal mine hole detection technology operation is cumbersome, not easy to control, and insufficient depth of jacking prob-lems, this paper designs a new type of mine hole detection small robot. Firstly, this paper ana-lyzes the function and structural design of the mine hole detection robot, designs the variable diameter function according to the characteristics of narrow and uneven mine holes in coal mines, and analyzes the mechanics of the critical parts through theoretical calculations; secondly, based on the three-dimensional modeling software, established the structural model of the small robot for mine hole detection; after that, designed the robot's hardware circuits and control pro-grams for the presence of water and gas inside the mine hole, highlighting the need to carry out a new type of mine hole detection small robot. After that, we designed the robot's hardware circuit and control program, giving particular emphasis to the safety design of the circuit for the pres-ence of water and gas inside the mine hole of the coal mine. Finally, to verify the feasibility of the design program, the basic parameters and function tests of the mine hole detection small robot are carried out. The experimental results show that the mine hole inspection small robot realized by this design can adapt to the working hole diameter from 65 mm to 100 mm, the maximum working power is only 12 W, and the maximum crawling speed is 3.96 m/min. The maximum crawling slope reaches 90°, which can meet the actual mine hole inspection needs. The research can provide theoretical and design guidance for developing the mine hole detection robot with substantial engineering practical reference value.

Treatment of the [AuCl(tetrahydrothiophene)] complex with 4-chloro-2-iodo-1-isocyanobenzene furnished the gold(I) compound [AuCl(CNC6H3-4-Cl-2-I)] (1). In the crystal structure of 1, the linear C–Au–Cl group is subject to the solid-state head-to-tail pairing which is determined by the aurophilic Au···Au and the rare π-holeCN···Cl interactions. These two types of structure-determining interactions are complementary to each other and the system of Au···Au and CCN···Cl contacts accomplishes 2D extended ladder-type architecture. In addition, the terminal I-atoms are involved in the three-center halogen bonding. Density functional theory calculations, employing a set of computational tools, verified the role of Au···Au and π-holeCN···Cl noncovalent bonds in the spectrum of noncovalent forces.

Background: Trigeminal neuralgia associated to vascular compression, by aberrant or ectopic arterial or venous vessels, is a frequent condition in clinical practice. Management with microvascular decompression through a Minimal invasive retrosigmoidal has shown high rates of pain control, with low complication rates and excellent therapeutic results. Objective: To describe the surgical technique and clinical outcomes in terms of pain relief after microvascular decompression for trigeminal nerve, through a minimal invasive retrosigmoidal parasterional burr-hole technique. Methods: A group of patients with trigeminal neuralgia refractory to medical management who underwent microvascular decompression considering outcomes based on Visual Analogue Scale (VAS), and Barrow Neurological Institute Pain Scale (BNIPS). Added to a technical note of the surgical technique for a minimal invasive retrosigmoidal parasterional burr-hole. Results: Twenty-two patients were evaluated, clinical assessment after surgical intervention showed a decrease pain according to VAS, resulting from an average preoperative state of 9.5 ± 0.37 to a postoperative condition of 1.32 ± 1.28, exhibiting statistically significant changes (p < 0.0001, d = 9.356). On the other hand, in relation to the BNIPS scale, a decrease from an average preoperative status of 4.55 ± 0.25, to a postoperative status at 12 months of 1.73 ± 0.54 was also demonstrated, showing significant changes (p < 0.0001, d = 3.960). Conclusion: Microvascular decompression of the trigeminal nerve through a minimal invasive retrosigmoidal parasterional burr-hole is feasible and can be a safe and effective technique for the management of pain.

One of the solutions of the Einstein equations, called McVittie solution, signifying a black hole embedded by the dynamic spacetime is studied. In the stationary spacetime the Mcvittie metric becomes the Schwarzschild-de Sitter metric (SdS). The geodesic of a freely falling test particle towards the black hole is examined in the SdS spacetime. It is found that unlike Schwarzschild case the potential of such particle becomes maximum at a point where it eventually stops to follow an unstable circular motion and then resumes its motion towards black hole center. It is shown that an observer or system of particles is spaghettified near the black hole singularity in the SdS spacetime. The dynamic of the universe in the framework of McVittie metric, being a generalized time dependent SdS solution, is represented in terms of that point, called stationary or turning point. The motion of the stationary point is studied in various regimes of the expanding universe and the possible outcomes are discussed in brief.

The effects of residual stress in a tungsten gate on a polysilicon channel in scaled 3D NAND flash memories were investigated using a technology computer-aided design simulation. The NAND strings with respect to the distance from the tungsten slit were also analyzed. The scaling of the spacer thickness and hole diameter induced compressive stress on the polysilicon channel. Moreover, the residual stress of polysilicon in the string near the tungsten slit had greater compressive stress than the string farther away. The increase in compressive stress in the polysilicon channel degraded the Bit-Line current (Ion) because of stress-induced electron mobility deterioration. Moreover, a threshold voltage shift (△Vth) occurred in the negative direction because of conduction band lowering.

The Schwarzschild metric describes a non-rotating and charge-free celestial body, and it results in things stopping at the event horizon of a black hole and spending infinite time across the event horizon by the observer far away from the black hole. The analysis of the particle’s behavior at the event horizon tells us that this solution predicts an un-expanded black hole which violates the astronomical observations and our knowledge about the black hole. Although some alternative metrics have been proposed, the singularity problem is still unsolved. In this research, the degenerate Fermi electron gas is used to reveal that the Fermi electron gas cannot shrink to a point no matter how large energy it obtains, so the singularity exists at the center very unreasonably. In order to avoid these problems, a finite-size nucleus of the black hole is proposed and reasonably explained by the behaviors of the Fermi electron gas and the Fermi neutron gas there. On the other hand, the Kerr-Newman metric is the one describing the rotating and charged black hole and the equation of the light velocity at each space point can be obtained. It tells us that there are two real and non-imaginary solutions for the radial speed of light at the position larger than the Schwarzschild radius.

In this article, we demonstrate the weak gravitational lensing in the context of Bocharova-Bronnikove-Melnikov-Bekenstein (BBMB) black hole. To this desire, we derive the deflection angle of light in a plasma medium by BBMB black hole using the Gibbons and Werner method. First, we obtain the Gaussian optical curvature and implement the Gauss-Bonnet theorem to investigate the deflection angle for spherically symmetric spacetime of BBMB black hole. Moreover, we also analyze the graphical behavior of deflection angle by BBMB black hole in the presence of plasma medium.

In this work, we present some results related with the issue of the Loop Quantum Black Holes (LQBH) thermodynamics by the use of the tunneling radiation formalism. The information loss paradox is also discussed in this context, where we have considered the influence of back reaction effects.

We present here a theory of Majorana excitons, photo-excited conduction electron-valence band hole pairs, interacting with Majorana Fermions in a Kitaev chain of semiconductor quantum dots embedded in a nanowire. Using analytical tools and exact diagonalisation methods we identify the presence of Majorana Zero Modes in the nanowire absorption spectra.

Bacteria develop various defense mechanisms against stresses, including the bacteriophage infection. The giant phiKZ phage infection induced the appearance of a pseudo-nucleus inside the bacterial cytoplasm. Here, we used FISH, electron tomography and analytical electron microscopy to study the morphology of this unique nucleus-like shell and to demonstrate the distribution of phiKZ and bacterial DNA in infected P. aeruginosa cells. The maturation of the pseudo-nucleus was traced in short intervals for 40 min after infection. This study was accompanied by the identification of phiKZ and bacterial DNA by real-time RCR. We demonstrated that phage DNA that isolated from the cytoplasm during all infection stages were compacted within the pseudo-nucleus in a specific structure. Bacterial DNA was diminished in the course of infection, but did not completely degrade until at least 40 min after phage application. The content of the total phage DNA, on the other hand, increased. EDX analysis confirmed these results and revealed that, during the infection, Sulfur content in the bacterial cytoplasm increased, which suggests the increase of DNA-binding Met-reach proteins synthesis, which could protect bacterial DNA from stress.

The use of mixed-state ionic beams in collision dynamics investigations is examined. Using high resolution Auger projectile spectroscopy involving He-like ($1s^2\thinspace^1\!S, 1s2s\thinspace^{3,1}\!S$) mixed-state beams, the spectrum contributions of the $1s2s\thinspace^3\!S$ metastable beam component is effectively separated and clearly identified. This is performed with a technique that exploits two independent spectrum measurements under the same collision conditions, but with ions having quite different metastable fractions, judiciously selected by varying the ion beam charge-stripping conditions. Details of the technique are presented together with characteristic examples. In collisions of 4 MeV B$^{3+}$ with H$_2$ targets, the Auger electron spectrum of the separated $1s2s\thinspace^{3}S$ boron beam component allows for a detailed analysis of the formation of the $1s2s(^3\!S)nl \thinspace^2\!L$ states by direct $nl$ transfer. In addition, the production of hollow $2s2p\thinspace^{1,3}\!P$ doubly- and $2s2p^2\thinspace^2\!D$ triply-excited states, by direct excitation and transfer-excitation processes, respectively, can also be independently studied. In similar mixed-state beam collisions of 15 MeV C$^{4+}$ with H$_2$, He, Ne and Ar targets, the contributions of the $1s^2$, $1s2s\thinspace^{3,1}S$ beam components to the formation of the $2s2p\thinspace^{3,1}\!P$ states by double-excitation, $1s\rightarrow2p$ excitation and transfer-loss processes can be clearly identified, facilitating comparisons with theoretical calculations.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

In this paper, we investigated the trajectory of the massive particle in the vicinity of a general spherical symmetric black hole. Also, in the framework of general sphericalily symmetric black hole, Pseudo-Newtonian potential (PNP) and effective potentials has been investigated. As an example, static spherically symmetric black hole in f(R) gravity is considered and presented the brief discussion on the structure of spacetime and horizons. We calculated energy and angular momentum in the framework of general relativity as well as in Pseudo-Newtonian theory. A graphical comparison of angular momentum in this both framework has been studied.

This letter aims to show the connection between the sinc approximation for high-energy absorption cross section and the shadow radius of the spherically symmetric black hole. This connection can give a physical interpretation of the absorption cross section in the eikonal limit parameters. Moreover, the use of this alternative way, one can extract its shadow radius from the absorption cross section in high energy limits to gain more information about the black hole spacetime. Our results indicate that the increasing the value of the shadow radius of the black hole, exponentially increase the the absorption cross section of the black hole in high-energy limits which can be captured by the Event Horizon Telescope (EHT) collaboration.

The main goal of this paper is to study the weak gravitational lensing by Horndeski black hole in weak field approximation. In order to do so, we exploit the Gibbons-Werner method to the optical geometry of Horndeski black hole and implement the Gauss-Bonnet theorem to accomplish the deflection angle of light in weak field region. Furthermore, we have endeavored to extend the scale of our work by comprising the impact of plasma medium on the deflection angle as properly. Later, the graphical influence of the deflection angle of photon on Horndeski black hole in plasma and non-plasma medium is examined.

This paper gives both a general canonical quantum gravity theory and the general canonical quantum gravity theories of the Universe and general black hole, and discovers the relations reflecting symmetric properties of the standard nonlinear gravitational Lagrangian, which are not relevant to any concrete metric models. This paper concretely shows the general commutation relations of the general gravitational field operators and their zeroth, first, second and third style, respectively, of high order canonical momentum operators for the general nonlinear system of the standard gravitational Lagrangian, and then has finished all the four styles of the canonical quantization of the standard gravity.

We consider rational nonlinear electrodynamics with the Lagrangian ${\cal L} = -{\cal F}/(1+2\beta{\cal F})$ (${\cal F}=(1/4)F_{\mu\nu}F^{\mu\nu}$ is the Lorentz-invariant), proposed in \cite{Krug2}, coupled to General Relativity. The effective geometry induced by nonlinear electrodynamics corrections are found. We determine shadow's size of regular non-rotating magnetic black holes and compare them with the shadow size of the super-massive M87* black hole imaged by the Event Horizon Telescope collaboration. Assuming that the black hole mass has a pure electromagnetic nature, we obtain the black hole magnetic charge. The size of the shadow obtained is very close to the shadow size of non-regular neutral Schwarzschild black holes. As a result, we can interpret the super-massive M87* black hole as a regular (without singularities) magnetized black hole.