In this work, two embroidered textile moisture sensors are characterized with three different conductive yarns. The sensors are based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidered conductor yarn. The performance comparison of 3 different type of conductive yarns has been addressed. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 30% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity and the used conductor yarns. This dependence points out the optimum conductive yarn to be used to develop wearable applications for moisture measurement.

In this work, an embroidered textile moisture sensor is presented. The sensor is based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidery conductor yarn composed by 99% pure silver plated nylon yarn 140/17 dtex. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 25% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity. Moreover, the reproducibility of the sensor performance subject to the manufacturing process variability and washing process is also evaluated. The results show that the manufacturing variability introduce a moisture measurement error up to 4%. The washing process impact on the sensor behavior after applying the first washing cycle implies a sensitivity reduction higher than 14%. Despite these effect, the textile sensor keeps its functionality and can be reused in standard conditions. Therefore, these properties point out the usefulness of the proposed sensor to develop wearable applications on health and fitness scope including the user needs to have a life cycle longer than one-time use

Modern electronic textiles are moving towards flexible wearable textiles, so-called e-textiles that have micro-electronic elements embedded onto the textile fabric that can be used for varied classes of functionalities. There are different methods of integrating rigid microelectronic components into/onto textiles for the development of smart textiles, which include, but are not limited to, physical, mechanical and chemical approaches. The integration systems must satisfy being flexible, lightweight, stretchable and washable to offer a superior usability, comfortability and non-intrusiveness. Furthermore, the resulting wearable garment needs to be breathable. In this review work, three levels of integration of the microelectronics into/onto the textile structures are discussed, the textile-adapted, the textile-integrated, and the textile-based integration. The textile-integrated and the textile- adapted e-textiles have failed to efficiently meet being flexible and washable. To overcome the above problems, researchers studied the integration of microelectronics into/onto textile at fiber or yarn level applying various mechanisms. Hence, a new method of integration, textile-based, has risen to the challenge due to the flexibility and washability advantages of the ultimate product. In general, the aim of this review is to provide a complete overview of the different interconnection methods of electronic components into/onto textile substrate.

The manuscript presents a novel approach to designing and fabricating a stretchable patch antenna designed for strain sensing and wireless communication of sensing data at the same time. The challenge lies in combining flexible and stretchable textile materials with different physical mor-phologies, which can hinder adhesion among multiple layers when stacked up, resisting the overall stretchability of the antenna. The proposed antenna design overcomes this challenge by incorpo-rating a lattice hinge pattern in the non-stretchable conductive e-textile, transforming it into a stretchable structure. The innovative design includes the longitudinal cuts inserted in both the patch and the ground plane of the antenna, allowing it to stretch along in the perpendicular direction. Implementing the lattice hinge pattern over the conductive layers of the proposed patch antenna in combination with a 2 mm thick Polydimethylsiloxane (PDMS) substrate achieves a maximum of 25% stretchability compared to its counterpart antenna without lattice hinge design. The stretchable textile antenna resonates around a frequency of 2.45 GHz and exhibits a linear resonant frequency shift when strained up to 25%. This characteristic makes it suitable for use as a strain sensor. Ad-ditionally, the lattice hinge design enhances the conformability and flexibility of the antenna compared to a solid patch antenna. The realized antenna gains in the E and H-plane were measured as 2.21 dBi and 2.34 dBi, respectively. Overall, the presented design offers a simple and effective solution for fabricating a stretchable textile patch antenna for normal use or as a sensing element, opening up possibilities for applications in communication and sensing fields.

This paper presents an alternative process to fabricate flexible bandpass filters by using embroidered yarn conductor on electronic-textile. The novelty of the proposed miniaturized filter is its complete integration on the outfit, with benefits in terms of compressibility, stretch ability and high geometrical accuracy, opening the way to develop textile filters in sport and medicine wearable applications. The proposed design consists of a fully embroidered microstrip topology with a length equal to quarter wavelength (λ/4) to develop a bandpass filter frequency response. A drastic reduction in size of the filter was achieved by taking advantage of a simplified architecture based on meandered-line stepped impedance resonator. The e-textile microstrip filter has been designed, simulated, fabricated and measured, with experimental validation at a 7.58 GHz frequency. The insertion loss obtained by simulation of the filter is substantially small. The return loss is greater than 20 dB for bands. To explore the relations between physical parameters and filter performance characteristics, theoretical equivalent circuit model of the filter constituent components were studied. The effect of bending of the e-textile filter is also studied. The results show that by changing the radius of bending up to 40 mm, the resonance frequency is shifted up 4.25 MHz/mm.

Although the complexity of physically based models continues to increase, they still need to be calibrated. In recent years, there has been an increasing interest in using new satellite technologies and products with high resolution in model evaluations and decision-making. The aim of this study is to investigate the value of different remote sensing products and groundwater level measurements in the temporal calibration of a well-known hydrologic model i.e. HBV. This has been rarely done for conceptual models as satellite data are often used in spatial calibration of the distributed models. Three different soil moisture products from ESA CCI SM v04.4, AMSR-E and SMAP, and total water storage anomalies from GRACE are collected and spatially averaged over the Moselle River Basin in Germany and France. Different combinations of objective functions and search algorithms all targeting a good fit between observed and simulated streamflow, groundwater and soil moisture are used to analyse the contribution of each individual source of information. Firstly, the most important parameters are selected using sensitivity analysis and then, these parameters are included in a subsequent model calibration. The results of our multi-objective calibration reveal substantial contribution of remote sensing products to the lumped model calibration even if their spatially distributed information is lost during the spatial aggregation. Inclusion of new observations such as groundwater levels from wells and remotely sensed soil moisture to the calibration improves the model’s physical behaviour while it keeps a reasonable water balance that is the key objective of every hydrologic model.

As both governments and customers push for sustainable and recyclable textile products, textile companies will have to change their linear business model to a circular one. The aim of the present work is to help these companies take action by providing an update of the state-of-the-art of textile recycling technologies. Extensive desktop research was performed in order to prepare an overview of existing textile recycling technologies, their current state and prognosis, including also facilitating technologies for sorting and disintegration of textile products as well as virtual platforms that connect stakeholders and inform consumers.

Hydrological models have been widely used for many purposes in water sector projects, including streamflow prediction and flood risk assessment. Among the input data used in such hydrological models, the spatial-temporal variability of rainfall datasets has a significant role on the final discharge estimation. Therefore, accurate measurements of rainfall are vital. On the other hand, ground-based measurement networks, mainly in developing countries, are either nonexistent or too sparse to capture rainfall accurately. In addition to in-situ rainfall datasets, satellite-derived rainfall products are nowadays available globally with high spatial and temporal resolution. An innovative approach called SM2RAIN that estimates rainfall from soil moisture data has been applied successfully to various regions. In this study, firstly soil moisture content derived from the Advanced Microwave Scanning Radiometer for the Earth observing system (AMSR-E) is used as input into the SM2RAIN algorithm to estimate daily rainfall, SM2R-AMSRE, at different sites in the Karkheh river basin (KRB), southwest Iran. Secondly, the SWAT (Soil and Water Assessment Tool) hydrological model is applied to simulate runoff using both ground-based observed rainfall and SM2R-AMSRE rainfall as input. The results reveal that the SM2R-AMSRE rainfall data are, in most cases, in good agreement with ground-based rainfall, with correlations R ranging between 0.58 and 0.88, though there is some underestimation of the observed rainfall, due to soil moisture saturation, not accounted for in the SM2RAIN equation. The subsequent SM2R-AMSRE- SWAT- simulated monthly runoff reproduces well the observations at the 6 gauging stations (with coefficient of determination, R² > 0.72), though with slightly worse performances in terms of bias (Bias) and root-mean-square error (RMSE) and, again, some systematic flow underestimation than the SWAT model with ground-based rainfall input. Furthermore, rainfall estimations of two satellite products of the Tropical Rainfall Measuring Mission (TRMM), 3B42 and 3B42RT, are used in the calibrated SWAT- model. The monthly runoff obtained with 3B42- rainfall have 0.39< R2 < 0.70 and are slightly better than those obtained with 3B42RT- rainfall, but not as good as the SM2R-AMSRE- SWAT- simulated runoff above. Therefore, in spite of the afore-mentioned limitations, using SM2R-AMSRE rainfall data in a hydrological model like SWAT, appears to be a viable approach in basins with limited ground-based rainfall data.

An accurate radiative transfer model (RTM) is essential for the retrieval of soil moisture (SM) from microwave remote sensing data, such as the passive microwave measurements from the Soil Moisture Active Passive (SMAP) mission. This mission delivers soil moisture products based upon L-band brightness temperature data, via retrieval algorithms for surface and root-zone soil moisture, the latter is retrieved using data assimilation and model support. We found that the RTM based on the tau-omega (?-ω) model, can suffer from significant errors over croplands (in average between -9.4K and + 12.0K for Single Channel Algorithm SCA; -8K and + 9.7K for Dual-Channel Algorithm DCA) if the vegetation scattering albedo (omega) is treated as a constant and the temporal variations are not accounted. In order to reduce this uncertainty, we propose a time-varying parameterization of omega for the widely established zeroth order radiative transfer ?-ω model. The main assumption is that omega can be expressed by a functional relationship between vegetation optical depth (tau) and the Green Vegetation Fraction (GVF). The validation was performed from 14 May to 13 December 2015 over 61 Climate Reference Network sites (SCRN) classified as croplands. The application of the proposed time-varying vegetation scattering albedo results in a consistent improvement for the unbiased root mean square error of 16% for SCA and 15% for DCA. The reduction for positive and negative biases was 45% and 5% for SCA and 26% and 12% for DCA, respectively. This indicates that vegetation dynamics on croplands are better represented by a time-dynamic single scattering albedo.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

Accurate estimates of daily rainfall are essential for understanding and modeling the physical processes involved in the interaction between the land surface and the atmosphere. In this study, daily satellite soil moisture observations from the Advanced Microwave Scanning Radiometer - Earth Observing System (AMSR-E) generated by implementing the standard NASA- algorithm are employed for estimating rainfall, firstly, through the use of recently developed approach, SM2RAIN (Brocca et al., 2013) and, secondly, the nonlinear autoregressive network with exogenous inputs (NARX) neural modelling at five climate stations in the Karkheh river basin (KRB), located in southwest Iran. In the SM2RAIN method, the period 1 January 2003 to 31 December 2005 is used for the calibration of algorithm and the remaining 9 months from 1 January 2006 to 30 September 2006 is used for the validation of the rainfall estimates. In the NARX model, the full study period is split into a training (1 January 2003 to 31 September 2005) and a testing (1 September 2005 to 30 September 2006) stage. For the prediction of the rainfall as the desired target (output), relative soil moisture changes from AMSR-E and measured air temperature time series are chosen as exogenous (external) inputs in NARX. The quality of the estimated rainfall data is evaluated by comparing it with observed rainfall data at the five rain gauges in terms of the correlation coefficient R, the RMSE and the statistical bias. For the SM2RAIN method, R ranges between 0.44 and 0.9 for all stations, whereas for the NARX- model the values are generally slightly lower. Moreover, the values of the bias for each station indicate that although SM2RAIN is likely to underestimate large rainfall intensities, due to the known effect of soil moisture saturation, its biases are somewhat lower than those of NARX. In conclusion, the results of the present study show that with the use of AMSR-E soil moisture products in the physically based SM2RAIN- algorithm as well as in the NARX neural network, rainfall for poorly gauged regions can be fairly predicted.

Plastic contamination is a burning issue costing the global cotton and textile industries billions of dollars annually. Any time plastics from different sources end up in a cotton lint bale, the value to the textile mills plummets significantly. Various industry players have therefore made a concerted effort to find lasting solutions to the menace posed by plastic to cotton profitability and sustainability. Nevertheless, until now, there have been no up-to-date comprehensive documents detailing the numerous and ever-growing efforts committed to solving this challenge. Therefore, this article provides a detailed yet compact review of this highly dynamic subject matter. First, it puts into perspective plastic contamination in the cotton and textile industries. Then, the cotton value chain is subdivided into phases from pre-cultivation to textile mills. The root causes of plastic contamination are discussed in each stage, followed by discussions of some already developed and emerging solutions in response to the challenge by the affected industries and researchers. Concluding from the author’s perspective, the paper makes projections for the future directions of plastic mitigation efforts within the cotton and textile industries. This article also infers from the reviewed literature that research on finding alternative materials to plastic as module wrap, the development of new, effective, and all-condition plastic sensing techniques for ginning and spinning equipment, and standardized protocols for UAV in-field surveys of plastic trash are some of the areas that will be beneficial to finding a permanent solution to the challenge.

Almost 115 million tons of fibers of which almost 90 million tons of chemical fibers were produced in the world in 2021, which are mainly used for the production of clothing and footwear. 30% of textile and apparel products are never sold, which means an extreme waste production. This article points out the possibilities of forecasting the sales of clothing in the case of one relatively large online store. Inadequate stocks of textile products in the company lead to loss and the need to sell products at a discount, which is undesirable for the company. The study in this article points to the calculation of the sales forecast for 2019 for the selected textile products, finding the analogy of the followed product sale. Sales for the years 2017 and 2018 serve as input data. The problem with textile products is that they have a short life cycle, i.e. the length of the life cycle is approximately half a year, and a high seasonality is also presented there. Therefore, the seasonal indices and Holt-Winters methods (multiplication and additional approaches) were used for products forecasting. Ultimately, this model could contribute to reducing the loss of unsold goods and thus reduce the waste of resources and increase the use of goods in other similar companies.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

Most historical buildings and structures in Oman were built using unreinforced stone masonry. These structures have deteriorated due to ageing of materials, environmental degradation, and lack of maintenance. This research investigates the physical, chemical, and mechanical properties of local building materials and the results of an experimental study on the out-of-plane bending effectiveness of an innovative strengthening technique applied to existing masonry walls. The technique consists of the application on one face of the walls of a basalt textile-reinforced sarooj mortar (TRM). Four-point bending tests of full-scale masonry samples (1000 mm width, 2000 mm height, and 350 mm depth) were carried out using one unreinforced specimen and three different cases of reinforced specimens. The performance of unreinforced and reinforced specimens was analyzed and compared. The strengthened specimens were able to resist moments of out-of-plane bending 2.5 to 3 times greater than those of unreinforced specimen (160%- 233% increase). Moreover, the strengthened walls were able to sustain higher deformations (deflections) than the unreinforced specimen ranging from 20%-130%. The results showed that using TRM was effective for the out-of-plane strengthening of stone masonry using a local material (sarooj) that is compatible with existing stone masonry building materials.

In this article we present the design and development of T-Shirt prototypes that embed novel textile sensors for the capture of cardio and respiratory signals. The sensors are connected through textile interconnects to either an embedded custom designed data acquisition and transmission unit or to snap fastener terminals for connection to external monitoring devices. Prototypes with diverse approaches of integration are presented. The performance of the wearable systems is addressed in terms of signal-to-noise ratio amplitude and signal interference caused by baseline wander and motion artifacts, through laboratorial tests with subjects in standing and walking conditions. Performance tests were also conducted in Hospital environment using a T-Shirt prototype connected to a commercial 3-channel Holter monitoring device. The textile sensors and interconnects were realized with the assistance of an industrial 6-needle digital embroidery tool and their resistance to wear addressed with normalized tests of laundering and abrasion. The main aspects of the system´s design leading to major improvements and failure factors are discussed. Pathways and methods for the overall system´s optimization are highlighted.

Purpose: The purpose of this study is to further explore how e-loyalty and E-marketing influences E-trust and satisfy the demand by offering fresh perspectives based on research as well as emphasis on the factors influencing the E-trust such as culture as a mediator. This study not only contributed theoretically but also presented practical implementations. Design/methodology/approach: Online survey was used to obtain data by focusing the Hospitality sector (Hotel Industry) and verifying the conceptual framework. Data was collected in multiple time lags. Findings: Findings showed that the E-trust influenced by E-loyalty and E-Marketing. E-trust comes from the previous experiences, e-loyalty and e-marketing. Further, some trends such as culture influenced the e-trust. Research limitation/implications: The present study is quite suitable for those Researchers interested in learning more about the effects of E-loyalty and E-marketing on user E-trust and how to mitigate cultural influences can benefit from the current study. This research also has implications for those who wish to improve market allure and survival in digital world. This study focused on the hospitality sector (Hotel Industry) in China; however, the sector and geography could be altered to suit the needs of the study's participants. Practical implications: The present study delivers the practical guidelines which are quiet suitable for understanding the formation of E-loyalty, E-marketing, and E-trust through which specific E-marketing strategy can be designed to deal with the consumer’s E-loyalty and their expectations as per their Cultural perspective. At some particular regions/countries, cultural trends are more important than practical market. This research study practically showed that how culture changed the consumer set of mind. Originality/value: The relationship between E-loyalty, E-marketing, E-trust, specifically with the cultural influence in digital market has been the subject of few research.

In this paper, we present the design, manufacturing and characterization of a soft textile-based clutch (TBC) that switches between locking and unlocking of its linear displacement by exploiting vacuum stimulation. The applied vacuum locks the relative sliding motion between two elaborated textile webbings covered by an elastic silicone rubber bag. Based on different fabrication techniques, such as silicone casting on textile, melt embossing for direct fabrication of miniature patterns on textile and sewing, we developed three groups of TBC samples based on friction and interlocking principles and we compared their performance in blocking configuration. The clutch with interlocking mechanism presented the highest withstanding force (150 N) respect to the one (54 N) recorded for the friction-based clutch. The simple and compact structure of the proposed clutch, together with the intrinsic adaptability of fabric with other clothing and soft materials, make it a proper solution for applications in soft wearable robotics and generally as locking and variable stiffness solution for soft robotic applications.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

Background and Objectives: The site types of Eucalyptus urophylla × Eucalyptus grandis clonal plantations in southern Yunnan were compared, aiming to provide basis for site selection and scientific plantations management. Materials and Methods: In this study, 80 standard plots were set up in the 6−9-year-old Eucalypts plantations in Pu'er City and Lincang City. Furthermore, the quantitative theory I model and canonical correlation analysis were used to analyze the relationship between dominant tree growth traits and site factors, and evaluate the growth potential of E. urophylla × E. grandis plantation. Results: The multiple correlation coefficient between 8 site factors (altitude, slope, slope level, soil thickness, slope direction, texture, soil bulk density, and litter thickness) and the quantitative growth of the dominant wood was 0.825 (P < 0.05). According to the correlation coefficient of the quantitative regression model, slope, altitude, and soil thickness were the main factors for the classification of E. urophylla × E. grandis plantations in southern Yunnan. In addition, E. urophylla × E. grandis plantations grew best downhill and mid uphill at relatively low altitude, where the soil layer was thick and composed of weathered red soil. Contrastingly, E. urophylla × E. grandis plantation growth was extremely poor in uphill sites at higher altitude, where the soil layer was thin and composed of semi-weathered purple soil. Furthermore, total N, and available B, Cu, and Zn content, as well as soil organic matter content in the soil had a great influence on the growth of E. urophylla × E. grandis. Conclusions: Nitrogen and phosphate fertilizer as well as trace elements such as B, Zn, and Cu can be properly applied in middle- and low-yield forests to promote the growth and development of E. urophylla × E. grandis plantations.

Background: Electronic cigarette (e-cigarette) use among youth in Poland has become very popular. The aim of this study was to identify potential points of access to these products among students aged 16-17 before implementation of sales restrictions to minors in Poland in November 2016. Methods: A school-based, cross-sectional survey was administered in 2015-2016 in 21 secondary/technical schools across two regions of Poland. Analyses focused on 341 students aged 16-17 who reported past 30-day use of e-cigarettes. Pearson chi-square analyses were utilized to examine associations between access-related items, e-cigarette use, and demographics. Results: Among youth e-cigarette users, the most common access to their first e-cigarette was from a friend (38%), followed by purchasing from vape shops (26%). Similar patterns emerged when students were asked about the access to their currently used e-cigarette. Most youth reported no difficulty purchasing cartridges/e-liquid containing nicotine (90%); the majority of users (52%) reported buying such products in vape shops. Conclusions: Prior to implementing age-related sales restrictions, youth access to e-cigarettes and paraphernalia did not pose any significant barriers. Poland’s introduction of a new age limit on e-cigarette sales may help limit the number of youth who purchase e-cigarettes from vape shops.

Heart rate (HR) and respiratory rate (RR) are two vital parameters of the body medically used for diagnosing short/long term illness. Out-of-the-body, non-contact HR/RR measurement remains a challenge due to imprecise readings. “Invisible” wearables integrated into day-to-day garments has the potential to produce precise readings with comfortable user experience. Sleep studies and patient monitoring benefit from “Invisibles” due to longer wearability without significant discomfort. This paper suggests a novel method to reduce the footprint of sleep monitoring devices. We use a single silver-coated nylon fabric band integrated into a substrate of standard cotton/nylon garment as a resistive elastomer sensor to measure air and blood volume change across the chest. We introduce a novel event-based architecture to process data at the edge device and describe two algorithms to calculate real-time HR/RR on ARM Cortex-M3 and Cortex-M4F microcontrollers. RR estimations show a sensitivity of 99.03% and a precision of 99.03% for identifying individual respiratory peaks. The two algorithms used for HR calculation show a mean absolute error of 0.81±0.97 and 0.86±0.61 beats/minute compared to a gold standard ECG-based HR. The event-based algorithm converts the respiratory/pulse waveform into instantaneous events, therefore, reducing the data size by 40-140 times and requires 33% less power to process and transfer data. Further, we show that events hold enough information to reconstruct the original waveform, retaining pulse, and respiratory activity. We suggest fabric sensors and event-based algorithms would drastically reduce the device footprint and increase the performance for HR/RR estimations during sleep studies providing better user experience.

Taking into consideration the seismic vulnerability of older buildings and the increasing need for reducing their carbon footprint and energy consumption, the application of an innovative system is investigated; the system is based on the use of textile reinforced mortars (TRM) and thermal insulation as a means of combined seismic and energy retrofitting of existing masonry walls. Medium scale tests were carried out on masonry walls subjected to out-of-plane cyclic loading. The following parameters were investigated experimentally: placement of the TRM in a sandwich form (over and under the insulation) or outside the insulation, one-sided or two-sided TRM jacketing and/or insulation, and the displacement amplitude of the loading cycles. A simple analytical method is developed and is found in good agreement with test results. Additionally, numerical modeling is carried out and is also found in good agreement with test results. From the results obtained in this study the authors believe that TRM jacketing may be combined effectively with thermal insulation, increasing the overall strength and energy efficiency of the masonry panels in buildings.

This paper develops the mathematical modeling and deflection control of a textile-reinforced composite integrated with shape memory actuators. The model of the system is derived using identification method and unstructured uncertainty approach. Based on this model and robust stability analysis a robust proportional-integral controller is designed for controlling the deflection of the composite. The performance of the proposed controller is compared with a classical one through experimental analysis.

Monitoring of structures is one of the engineering challenges of the 21st century. At the same time, as a result of changes in the conditions of use, design errors, many building structures require strengthening. The article presents research on the development of the external strengthening carbon fiber textile with an option of self-sensing. The idea is based on the pattern of resistive strain gauge, where thread is provided in a zig-zag of parallel lines. Already the first laboratory tests showed the high efficiency of the system in the measurement of strains, but also revealed the sensitivity of measurement to environmental conditions. The article presents studies on the influence of temperature and humidity on the measurement. To separate those effects, resistance changes were tested on unloaded concrete and wooden samples. The models were placed in a climatic chamber and the daily cycle of temperature and humidity changes was simulated. The results of the research confirm preliminary observations. Resistivity growths with the temperature. This effect is more visible on concrete samples, presumably due to its greater natural humidity. The strain measurement with carbon fibers is very sensitive to temperature changes and application of this method in practice requires compensation.

The potential of biological consortia designed for laccase production and dye treatment is discussed in this review. The poor yields in laccase production and low efficiency in dye decolorization of monoculture-based treatments has encouraged the use of designed biological consortia. A consortium is a system where the growth of two or more organisms, chosen to improve a particular bioprocess, is induced in the same medium. Chemical and natural mediators are being replaced by consortia for the production of laccases because, in addition to being less toxic, they induce new enzyme isoforms and lead to high laccase yields. On the other hand, consortia act synergistically in the decolorization of azo dyes through the enzymes they produce, so overall degradation is improved. Designed consortia are an attractive alternative still in development that could provide new biotechnological tools for the treatment of textile effluents.

The rapid development of China’s textile industry leads to consumption and pollution of large volumes of water. Therefore, the textile industry has been the focus of water conservation and waste reduction in China’s 13th Five-Year Plan (2016–2020). The premise of sustainable development is to achieve decoupling of economic growth from water consumption and wastewater discharge. In this work, changes in blue water (water consumption), grey water (water pollutants), and water footprints of the textile industry from 2001 to 2014 were calculated. The relationship between water footprint and economic growth was then examined using the Tapio decoupling model. Furthermore, factors influencing water footprint were determined through logarithmic mean Divisia index (LMDI) method. Results show that the water footprint of China’s textile industry has strongly decoupled for five years (2002, 2006, 2008, 2011, and 2013) and weakly decoupled for four years (2002, 2007, 2009, and 2010). A decoupling trend occurred during 2001–2014, but a steady stage of decoupling has not been achieved yet. Based on the decomposition analysis, the total water footprint is mainly increased by production scale and inhibited by the technology. In addition, the effect of industrial structure adjustment is relatively weak.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

Increased proliferation of IT services in all sectors has reinforced the adoption and diffusion across all levels of education and training institutions. However, lack of awareness of and knowledge about the key challenges and opportunities of elearning, seem to allude policymakers, resulting in low adoption or increased failure rate of many e-learning projects. Our study tries to address this problem through a review of relevant literature in e-learning. Our goal was to draw from the existing literature, insights into the opportunities and challenges of e-learning diffusion, and the current state-of-research in the field. To do this, we employed a systematic review of literature on some of the salient opportunities and challenges of e-learning innovation for educational institutions. These results aimed to inform policymakers and suggest some interesting issues to advance the research and adoption and diffusion of e-learning. Moreover, the bibliometric analysis shows that the field is experiencing high research attraction among scholars. However, several research areas in the field witnessed relatively low research paucity. Based on these findings, we discussed topics for possible future research.

Eucalyptus, a therapeutic plant mentioned in the ancient Algerian pharmacopeia, specifically two species belonging to the Myrtaceae family - E. radiata and E. cinerea, were investigated in this study for their antibacterial, antioxidant, and anti-inflammatory properties. The study used aqueous extracts (AE) obtained from these plants, and the extraction yields were found to be dif-ferent. The in vitro antibacterial activity was evaluated using a disc diffusion assay against three typical bacterial strains. The results showed that E. radiata EAq was effective against all three strains, while E. cinerea EAq was only effective against E. coli. Both extracts displayed significant antioxidant activity compared to BHT. The anti-inflammatory impact was evaluated using a pro-tein (BSA) inhibition denaturation test. The E. radiata extract was found to inhibit inflammation by 75% at a concentration of 250 g/ml, significantly higher than the placebo. Ellagic acid, a pri-mary phytochemical found in the extracts, demonstrated noteworthy toxic and pharmacokinetic characteristics and a maximum binding energy of -7.53 kcal/mol for its anti-TyrRS activity in sili-co. The study suggests that the extracts and their primary phytochemicals could enhance the effi-cacy of antibiotics, antioxidants, and non-steroidal anti-inflammatory drugs (NSAIDs). As phar-maceutical engineering experts, we believe this research contributes to developing natural-based drugs with potential therapeutic benefits.

Communication and effective interactions are inevitable necessities in every organizational setting. In this era of information and communication technology, where limitations and difficulties in proper communication and interactions between different entities of various organizations have been reduced maximally, the government, stakeholders, and citizens of the different nations should also utilize these available tools in a way to improve the maximum performance in governance through interactions and e-participation between the citizens, stakeholders, and the government parastatals. This research focuses on examining the available and most preferred applications or platforms which encourage the best level of communication and interaction through E-participation among the citizens, stakeholders, and government from the local government lev-el taking Nigeria as a case study

Dyes, as indigo carmine have become indispensable to modern life being widely used in food, textile, pharmaceutical, medicine and cosmetic industries. Although indigo carmine is considered toxic and presents many adverse effects, it is heavily used in the food industry because the blue pigment is difficult to obtain from natural sources and is one of the most used dyes in the textile industry, especially for dyeing denim. Also, indigo carmine is one of the dyes used in medicine as diagnostic agent because it has impressive applicability in terms of diagnostic methods and surgical procedures. In the literature it is reported that indigo carmine is toxic for humans and can cause various pathologies, such as hypertension, hypotension, skin irritations, corneal and conjunctival disorders or gastrointestinal disorders. In this review, we discuss the structure and properties of indigo carmine, its use in various industries and medicine, the adverse effects of its ingestion, injection or skin contact, the effects on environmental pollution and its toxicity testing.

This study demonstrates the viability of an orange peel-based adsorbent as sustainable alternative for the elimination of the disperse dye C.I. Disperse Blue 56 present in waste waters of the dyeing industry of textiles. The effectiveness of the adsorbent is evaluated at different pH values and the adsorption capacity is determined by systematically comparing orange peel and the final adsorbent chemically treated. Results reveal an spontaneous coagulation-flocculation phenomenon of the dispersed dye at low pH values which represents a sustainable way for the recovery and possible re-use of the dye, together with the industrial valorisation of a wasting product as is orange peel.

The aim of this short communication is to find out the legal set up that complies with the environmental management in the textile sector of Bangladesh. This sector is the one of the biggest contributor to the economy of the nation. This sector contributes 81% to the total export earnings involving an immense number of stakeholders to its production processes. It is also true that this sector is largely responsible for the overall environmental pollution through its effluent discharge. The findings suggest that there are both international and national legal guidelines exist for environmental management in the said sector. In order to improve the environmental standards rehearsing lawful instruments is compulsory for the said industries.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

According to the World Health Organization, approximately 20 million people worldwide are infected annually with the hepatitis E virus (HEV). There are 4 main genotypes of HEV. Genotype 1 and genotype 2 are common in developing countries and are transmitted by contaminated water from a fecal-oral route. Genotype 3 and genotype 4 are common in developed countries and can lead to occasional transmission to humans by undercooked meat. Hepatitis E virus 1 and HEV3 can lead to fulminant hepatitis, and HEV3 can lead to chronic hepatitis and cirrhosis in immunocompromised patients. The majority of patients with HEV infection are asymptomatic and usually have spontaneous viral clearance without treatment. However, infection in immunocompromised individuals can lead to chronic HEV infection. Both acute and chronic HEV infections can have extrahepatic manifestations. No specific treatment is required for acute HEV infection, no treatment has been approved in chronic infection and no HEV vaccine has been approved by the (United States) Food and Drug Administration. This review focuses on the molecular virology (HEV life cycle, genotypes, model systems, zoonosis), pathogenesis, clinical manifestation, and treatment of chronic HEV infection, especially in immunocompromised patients, to provide clinicians a better understanding of the global distribution of these infections and the significant effect they can have on immunocompromised patients.

This work investigated the effects of manufacturing variations including coil resistance, initial pod mass, and e-liquid color on coil lifetime and aerosol generation of Vuse ALTO pods. Random samples of pods were used until failure (where e-liquid was consumed, and coil resistance increased to high value indicating a coil break). Initial coil resistance, initial pod mass, and e-liquid net mass ranged between 0.89 to 1.14 [], 6.48 to 6.61 [g], and 1.88 to 2.00 [g] respectively. Coil lifetime with light color e-liquid was (mean) = 149, (standard deviation) = 10.7 puffs while pods with dark color e-liquid was = 185, = 22.7 puffs with a difference of ~36 puffs (p &lt;0.001). Total mass of e-liquid consumed until coil failure was = 1.93, = 0.035 [g]. TPM yield per puff of all test pods for the first session (brand new pods) was = 0.0123, = 0.0003 [g]. During usage, TPM yield per puff of pods with light color e-liquid was relatively steady while it was continuously decreasing for pods with dark e-liquid. Coil lifetime and TPM yield per puff were not correlated with either variation in initial coil resistance or variation in initial pod mass. The absence of e-liquid in the pod is an important factor in causing coil failure. Small bits of the degraded coil could be potentially introduced to the aerosol. There is a potential correlation of e-liquid color with both coil lifetime and TPM yield per puff. Change of e-liquid color might have been a result of oxidation which changed some nicotine into nicotyrine.

This study focuses on a new class of functions called sub-b-s-preinvex, that is a generalization of sub-b-s-convex and preinvex functions, and discusses some of their properties. A new sub-b-s-preinvex programming is introduced and the sufficient conditions of optimality under this type of function is established.

The alkylation of 1,1,2-trimethyl-1H-benzo[e]indole with 2-chloroacetamide, followed by work-up of the reaction mixture with a base and the subsequent treatment of a crude product with acetic acid gives 10a,11,11-trimethyl-10a,11-dihydro-8H-benzo[e]imidazo[1,2-a]indol-9(10H)-one. The structure assignments were based on data from ¹H, ¹³C and ¹⁵N NMR spectroscopy. The optical properties of the obtained compound were studied by UV-vis and fluorescence spectroscopy.

The increasing popularity of carbon-reinforced concrete (CRC) is attributed to its exceptional tensile properties, low density, no corrosion phenomenon, and remarkable flexibility, allowing it to be easily shaped into various forms. This research investigates the feasibility of using a special 2D Netzgitterträger (NetzGT) reinforcement system, featuring a net-shaped fabricated textile made of multiple diagonally offset rovings with overlapping edge strands, as a viable alternative to traditional steel reinforcement in concrete beams. This reinforcement is manufactured from carbon rovings with three different diagonal angles of 50⁰, 60⁰, and 70⁰ respectively. Laboratory experiments were conducted to assess the mechanical behavior of beams reinforced with the 2D NetzGT reinforcement. Bending and shear tests were performed on beams with varying numbers of overlapped edge roving and roving angles to evaluate the tensile capacity and failure characteristics of beams. The increase in the number of overlapped edge rovings led to a noticeable increase in the maximum tensile force. Tensile tests on strands were also performed with the increasing number of overlapped rovings to analyze their tensile strength. Additionally, single yarn pull-out tests were also conducted to examine the influence of the roving angle on the bond strength between the carbon textile roving and the concrete matrix

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. How-ever, challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investiga-tion of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for mo-tion capture for medical devices. Several variables were considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through experimental evaluation, by determining the gauge factor, its non-linearity, hysteresis and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50 %, 12,5 % hysteresis, and 0.3 % nonlinearity in parts.

In this work we present a study of impact of textile materials used in health care facilities on microbial colonization of textile surfaces. Polypropylene yarns doped with silver phosphate glass and zinc pyrithione were prepared and used for production of bed sheets and clothing for healthcare personnel. Subsequently measurements of airborne particles and viable microorganisms on given textiles were conducted in a private surgery clinic during 3 weeks comparing the counts of viable microorganisms before and after replacing of staff clothing and bedding on examination and surgical bed with said polypropylene cloth. In this study a significant reduction of viable airborne fungi and viable microorganisms on monitored textiles was observed by multiple methods.

Many pigments and dyes are not only valuable molecules in manufacturing, but also pollutants. Science has certainly been producing sustainable alternatives to counter the issue of dyes, but this is not enough. There is also a need for change in the business attitude and leadership approach of the organizations that operate in the industry. Only through the successful combination of new technologies and forward-looking decision making, it will be possible to alter the status quo and deal with the multiple environmental and supply chain challenges that these businesses are and will be facing. With a focus on colorants, this critical review article will reflect on the importance of both a biotechnological approaches and sustainable leadership to achieve a sustainable, forward-looking fashion industry.

The field of power harvesting has experienced significant growth over the past few years due to the ever-increasing desire to produce portable and wireless electronics with extended lifespans. The present work aims to introduce an approach to harvesting electrical energy from a mechanically excited piezoelectric element and investigates a power analytical model generated by a smart structure of type polyvinylidene fluoride(PVDF) that can be stuck onto fabrics and flexible substrates, although we report the effects of various substrates and investigates the sticking of these substrates on the characterization of the piezoelectric material.

Electrospinning polymer fibers for is a well-understood process, primarily resulting in random mats or single strands. More recent systems and methods have allowed for the production of nanofiber yarns (NFY) for ease of use in textiles. This paper presents a method of NFY manufacture using a simplified dry electrospinning system to produce self-assembling functional NFY capable of conducting electrical charge. The polymer is a mixture of cellulose nanocrystals (CNC), polyvinyl acrylate (PVA) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). When treated with Ethylene Glycol (EG) to enhance conductivity, fibers touching the collector plate align to the applied electrostatic field and grow, twisting together as additional nanofiber polymer is added by the jet. The longer the electrospinning continues, the longer and more uniformly twisted the NFY becomes. This process has the added benefit of reducing the electric field required for NFY production from >2.43 kV cm-1 to 1.875 kV cm-1.

This work attempted to fabricate superhydrophobic fabric via simple immersion technique. Textile fabrics were coated with silica nanoparticles prepared from tetraethoxysilane (TEOS) to obtain sufficient roughness with hydrophobic surface chemistry. Then the coated fabrics were treated with polydimethylsiloxane (PDMS) and aminopropyltriethoxysilane (APTES) to reduce the surface energy. The effects of PDMS concentration on the surface morphology and superhydrophobicity of as-prepared fabric were investigated. The morphology and the composition of superhydrophobic fabric was characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDS) and Fourier transform infrared (FTIR) spectroscopy. The results revealed the formation of spherical silica nanoparticles with average particle size of 250 nm throughout the fabric surface. The possible interactions between silica nanoparticles and APTES, as well as the fabrics were elucidated. Investigating the hydrophobicity of fabrics via water contact angle (WCA) measurement showed that the treated fabric exhibits excellent water repellency with a water contact angle as high as 151° and a very low water sliding angle. It also found that the treated fabric maintained most of its hydrophobicity against repeated washing. The comfort properties of the obtained superhydrophobic fabrics in term of air permeability and bending length did not reveal any significant changes.

Multi-sensor data fusion of E-tongue and E-nose can provide a more comprehensive and more accurate analysis results. However, it also brings some redundant information, it is a hot issue to reduce the feature dimension for pattern recognition. In this paper, the taste-olfactory data fusion based on E-tongue and E-nose combined with Support Vector Machine (SVM) was used to classify five different beers. First, the taste and olfactory feature information were obtained based on E-tongue and E-nose. Second, the original feature data of single system were fused, then Principal Component Analysis (PCA) was applied to extract principal components, Genetic Algorithm-Partial Least Squares (GA-PLS) was used to select the characteristic variables, 20 subsets were generated with those variables based on the best Variable Importance of Projection (VIP) score. Finally, the classification models based on SVM were established, also c and g of SVM were calculated by Grid Search (GS), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO), the classification results of all subsets were obtained. The results showed that the classification accuracy using data fusion was much higher over single E-tongue and single E-nose, and the variable selection method by VIP had the best classification performance in #12 subset coupled with GA-SVM.

Background - Chronic kidney disease with unknown aetiology (CKDu) is a progressing disease which is affecting many Sri Lankans’ yearly, this disease is slow progressive, irreversible and asymptomatic disease. Patients suffering from CKDu over the past two decades have been evaluated using the estimated glomerular filtration rate (e-GFR). This is the standard test performed under WHO guidelines to investigate and grade the CKDu, and this creatinine clearance is measured in this in order to grade the patient. Backache has been a common symptom presented in most of the chronic kidney disease patients (CKD), patients with CKDu are liable to get backache due to the renal failure that takes place (Jayathilake et al., 2013; Redmon et al., 2016). Objective – To detect a correlation between serum creatinine values and level of backache presented in the patient. Method -Using an interview based questionnaire to assess patients’ body condition and the degree of backache is assessed, 59 patients were part of the study for a period of five months and had an average age of 60.3 years. The questionnaire answers are scaled into four main types of backache from the least to the most painful based on the pain scale adapted from Kapkia. Serum creatinine is measured using an automated analyzer which is measured using Jaffe’s reaction. Using Pearson R correlation, the relationship was determined between serum creatinine and backache (Kafkia et al., 2011). Results – The results were obtained for 58 patients (n=58), where the mean backache score was 2.30 and mean serum creatinine value 2.77. The Pearson R value obtained was 0.01 which is indicating almost no relationship between backache and serum creatinine. Patients with stage 3 kidney disease (n=14) had an average E-GFR of 38.0, stage 4 (n=38) with 22.3 and stage 5 (n=6) with 14.0. Conclusion – Backache can be used an indicator of CKDu since it is presented in most patients’ suffering from the disease but unable to be used to determine the stage of CKDu suffered by the patient due to the external causes that leads to backache. Several predisposing factors such as temperature, water source and agricultural activity can influence the backache.

The investment in digital e-Health services is a priority direction in the development of global health care systems. While people are increasingly using the Web for health information, it is not entirely clear what is the physicians’ attitude towards digital transformation, and the acceptance of new technologies in healthcare. The aim of this cross-sectional survey study was to investigate physicians’ self-digital skills, and their opinions on obtaining online health knowledge by patients, as well as the recognition of physicians’ attitudes towards e-Health solutions. Principal Component Analysis (PCA) was performed to emerge the variables from self-designed questionnaire, and cross-sectional analysis comparing descriptive statistics and correlations for dependent variables using the one-way ANOVA (F-test). 307 physicians participated in the study, reported using the internet mainly several times a day (66.8%). Most participants (70.4%) were familiar with new technologies and rate their e-Health literacy high, although 84.0% reported the need for additional training in this field, and reported a need to introduce a larger number of subjects shaping digital skills (75.9%) in medical studies 53.4% of physicians perceived Internet-sourced information as sometimes reliable, and in general assessed the effects of using it by their patients negatively (41.7%). Digital skills increased significantly with frequency of internet use (F = 13.167; p = 0.0001), and decreased with physicians’ age, and the need for training. Those who claimed that patients often experienced health benefits from online health showed higher digital skills (-1.06). Physicians most often recommended their patients to obtain laboratory test results online (32.2%), and to arrange medical appointments via the Internet (27.0%). Along with the deterioration of physicians’ digital skills, the recommendation of e-Health solutions decreased (r = 0.413), and lower the assessment of e-Health solutions for the patient (r = 0.449). Physicians perceive digitization as a sign of the times, and frequently use its tools in daily practice. The evaluation of Dr. Google’s phenomenon and online health is directly related to their own e-Health literacy skills, but there is still a need for practical training to deal with digital revolution.

The new need to move to an online mode of administration has necessitated the adoption of Software-as-a-Service (SaaS) and Platform-as-a-Service (PaaS). The conventional paper-based administrative memorandum is relatively costly, requires manpower, insecure and non-confidential, prone to unauthorized access and has a relatively slow cycle time; among others. An electronic memo (e-memo) can save cost, offer high speed of processing, reliability and security. The aim of this work was to conceptualize, design and develop a novel semantic web-based memo platform that allows for handling memos within an organization. The tools used include HTML, CSS, PHP, JavaScript, jQuery and AJAX, MySQL. The developed system was tested in three stages. Testing was done in the Department of Computer Science of the institution of case study, then in the Faculty of Science and finally in the entire Lagos State University. Agile development method was used in the development process. The designed system was hosted on a cloud-server and a total of 43 test cases were considered and an average of four minutes was recorded for a complete memo cycle. eMemo allows users to generate, sign, treat and memo electronically. It is such a useful tool that will enhance information processing in a faster, standardized and more secure manner.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity or remain stress-free. Contrary to this are shell structures, which can bridge large spans with little material if designed well. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behaviour on a smaller scale by dissolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is to be developed in an ongoing research project, basic analysis approaches of which are presented in this paper. In addition to the basic workflow and the programs used, the material models used, and their calibration are described on the basis of tests on textile reinforced concrete (TRC) samples. Initial tests on two individual TRC served to verify the model.

This scholarly investigation conducts a rigorous exploration of Bangladesh's textile sector spanning the years 2011 to 2022, centering its attention primarily on the development of an intricate econometric framework. The study unveils profound insights into the sector's growth trajectories, the intricate dynamics of global demand, the undulating fluctuations of interest rates, and other pivotal economic gauges. The core component of this research, the econometric model, adeptly prognosticates textile exports through the incorporation of multifarious variables, encompassing the count of garment establishments, the magnitude of the workforce, market penetration, worldwide demand patterns, currency exchange rates, and interest rate fluctuations. Notably, the model attains a lofty degree of explicative potency, with an R-squared coefficient approximating 0.756, thereby attesting to its remarkable capacity to elucidate variances in textile export values. These discoveries carry substantial consequences for policymakers and stakeholders within the industry, as they bestow upon them a potent instrument for judicious decision-making and strategic blueprinting within Bangladesh's textile domain. The model accentuates the paramount significance of global demand and market share, concurrently accentuating the latent repercussions posed by fluctuations in interest rates.This research provides valuable insights into promoting the industry's sustainable growth, diversification, and resilience in the face of economic challenges.

To digital grade the color fastness of fabrics after rubbing, an automatic grading method based on spectral reconstruction technology and BP neural network was proposed. Firstly, the modeling samples are prepared by rubbing the fabrics according to the ISO standard of 105-X12. Then, to comply with visual rating standards for color fastness, the modeling samples are professionally graded to obtain the visual rating result. After that, a digital camera is used to capture digital images of the modeling samples inside a closed and uniform lighting box, and the color data values of the modeling samples are obtained through spectral reconstruction technology. Finally, the color fastness prediction model for rubbing was constructed using the modeling samples data and BP neural network. The color fastness level of the testing samples was predicted using the prediction model, and the prediction results were compared with the existing color difference conversion method and curve fitting method. Experimental show that the prediction model of fabric color fastness can be better constructed using the BP neural network, where the root-mean-square error of the prediction for the training sample is 0.30, and the root-mean-square error of the prediction for the test sample is 0.25. The overall performance of the method is slightly better than the color difference conversion method, and it is significantly outperforming the curve fitting method. It can be seen that the digital rating method of fabric color fastness to rubbing based on spectral reconstruction and BP neural network has a high consistency with the visual evaluation, which will help for the automatic color fastness grading.

Fiber-cement composites were prepared from cellulosic cotton residue (CCR) arise from sanding process (emerizing). The effect of different concentrations: 0.5% and 1%, and granulometry: thick (retained in a14 mesh sieve) and thin (retained in a 48 mesh sieve) of this residue were evaluated on tensile strength of cement slurries with seven (07) curing days. To characterize the CCR, TGA, FT-IR, SEM and XRD analysis were performed and the residue resistance in an alkaline environment was also evaluated. Splitting tensile strength test, known as Brazilian Test, was used to assess effects of the fibers on the mechanical behavior of cement matrix. Analyzing the results, the CCR proved to be resistant in an alkaline environment, meaning that it can withstand the alkaline environment of cement matrix. The results showed an improvement superior to 17% in tensile strength for 1% of CCR. Therefore, the CCR presents a great application potential in cement pastes used for oil well cementing that requires to increase its tensile strength, once a significant improvement was achieved with a low-residue employee.

In the industrial sector, the financial gain is generally considered at the cost of environmental degradation. The environmental protection and economic benefit are common conflicting objectives in many optimization problems. In any multi-criteria problem, the most challenging part is to optimize the conflicting goals. But if these objectives become non-conflicting, then the problem can be solved with ease. This paper is all about minimizing the environmental impact of industrial processes while maximizing the net economic benefit. There is a general misconception of linking the environmental protection with a financial loss. This is not always true; the Eco-Efficiency or Cleaner Production Technology (CPT) is a perfect example to disprove this notion. Economics of CPT regarding water savings for the textile-processing sector in Pakistan has been analyzed in this paper. Changes in water use before and after the implementation of water conserving technologies in the textile sector of Pakistan from a study conducted by the Cleaner Production Institute (CPI) are utilized to perform a cost-benefit analysis. Direct financial benefits that could be achieved through the application of these technologies are presented only. Other environmental benefits, though not described here, are of no less importance. The study results reveal that very high potential of water savings exists for most of the investments on CPT.

Garment sector has crucial working field in Turkey.It has also very high risky occupational health conditions and safety.The objective of this study is to define level of job level, work-related stress’ symptoms, social support and coping mechanisms of garment workers and to determine any related factors.This study is descriptive and cross-sectional. The study population comprised garment workers in the 16-65 age range. The data was collected by Assessment Form, The Brief Stress Coping Profile and Brief Job Stress Questionnaire. The level of work-related stress was statistically higher among the workers who had chronic disease, low economic, education status and poor quality of sleep. Psychological and physical physiological reactions to stress were found higher among women workers and those with chronic disease.It also was seen that job stress scores had a meaningful relationship with “emotional expression involving others” (r =.20) and “Avoidance and suppression” coping profile (r =.16; p <.01).Psychological symptom scores were found to have a low level of meaningful relationship with “Seeking help for solution” (r =-.08), “changing point of view” (r=.13) and “emotional expression involving others” coping profiles (r=.21). Work-related stress causes many health and behavioral problems. Work related reasons and coping profiles have powerful effects on stress.

E-petitioning is a useful object of study for observing the potential emergence of a new relationship to politics and new forms of political participation. Access to a dataset of hundreds of thousands of users of an electronic petitioning platform, provides the opportunity to overcome a certain number of limitations that are associated with traditional methods of studying political participation, since it allows us to focus on the reality of the signatories’ behaviour rather than on their declarations. We follow the traces left by the petitioners on this site to better understand the process of dissemination of an online petition, and its linked with offline activities. Our examination of the three most signed petitions in the ‘environment’ category, combining an analysis of their petitioning dynamics and an analysis of the comments attached to them, allows us to show: firstly, that there is an interwoven relationship between the local anchoring of the mobilisation and the processes of dissemination by which petitions extend from local signatories to signatories who are geographically more distant; and secondly, that it is not accurate to imagine that just anyone can sign any petition, since petitioning dynamics proceed from one person to the next, whether these dynamics start from a pre-existing local anchorage on the ground, or act through a platform effect which is dependent on the attractiveness of the petition in question.

Enteroaggregative Escherichia coli (EAEC) is an emerging pathogen frequently associated with acute diarrhea in children and travelers to endemic regions. EAEC was found the most prevalent bacterial diarrheal pathogen from hospitalized Bolivian children less than five years of age with acute diarrhea from 2007 to 2010. Here, we further characterized the epidemiology of EAEC infection, virulence genes, and antimicrobial susceptibility of EAEC isolated from 414 diarrheal and 74 non-diarrheal cases. EAEC isolates were collected and subjected to a PCR-based virulence gene screening of seven virulence genes and a phenotypic resistance test to nine different antimicrobials. Our results showed that atypical EAEC (a-EAEC, AggR-negative) was significantly associated with diarrhea (OR, 1.62, 95% CI, 1.25 to 2.09, P < 0.001) in contrast to typical EAEC (t-EAEC, AggR-positive). EAEC infection was most prevalent among children between 7 - 12 months of age. The number of cases exhibited a biannual cycle with a major peak during the transition from warm to cold season (April – June). Both typical and a-EAEC infections were graded as equally severe; however, t-EAEC harbored more virulence genes. aap, irp2, and pic were the most prevalent genes. Surprisingly, we detected 60% and 52.6% of multidrug resistance (MDR) EAEC among diarrheal and non-diarrheal cases. Resistance to ampicillin, sulfonamides, and tetracyclines was most common, being the corresponding antibiotics, the ones that are frequently used in Bolivia. Our work is the first study that provides comprehensive information on the high heterogenicity of virulence genes in t-EAEC and a- EAEC and the large prevalence of MDR EAEC in Bolivia.

O26 enteropathogenic Escherichia coli (EPEC), possesses a unique pseudocapsule composed of polysaccharides identical to the O antigen in their lipopolysaccharide (LPS) membrane. Therefore, the impact of O26 polysaccharides on the immune evasion mechanisms of capsulated O26 EPEC was investigated. Our findings reveal that the concentration of GlcNAc, an immunodominant unit of O26 polysaccharides capable of activating the MBL (Mannose Biding Lecting) pathway of the complement system, was found to be lower in capsulated EPEC O26 compared to naked shiga toxin-producing E. coli (STEC) O26 strain. It was noted that, unlike the naked STEC strain, the capsulated EPEC O26 strain was protected against lysis by the alternative pathway of the com-plement system by inhibiting C3b adhesion to its bacterial surface. Capsulated EPEC O26 strains were also able to avoid phagocytosis by macrophages. However, the immune evasion provided by the capsule was overcome in the presence of anti-O26 polysaccharide antibodies. Additionally, these antibodies were able to recognize O26 EPEC in the presence of biofilm and inhibit their adhesion to human epithelial cells. Overall, the results indicate that the O26 polysaccharides can generate an effective humoral immune response, making them promising antigens for the de-velopment of a vaccine against capsulated O26 E. coli

For better export performance in cross border e-commerce, a contingency model integrates e-commerce into traditional export marketing strategy (EMS) with internal and external determinants of EMS. However, EMS of Micro, small, and medium-sized enterprises (MSMEs) is understudied. This study validates and modifies existing model for MSMEs. As a qualitative study, multiple sources of data including interviews, internal documents, and group discussions were used regarding business cases of entrepreneurs and supporting organizations in Mongolia and Korea. This research suggets contingency model for MSMEs with modified factors and different strategies in each factor. Specifically, intermal determinants are managerial capability, product competitiveness, and strategic marketing orientation. External determinants are export market competitivceness, export market infrastructure and entry barriers. EMS for MSMEs consists of the same factors with the original model but come up with different strategies. Theoretical and managerial implications were discussed.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

(1) Background: Spain launched an official campaign, #EsteVirusLoParamosUnidos, to try and unite the efforts of the entire country through citizen cooperation to combat coronavirus. The research goal is to analyze the Twitter campaign’s repercussion on general citizen feeling. (2) Methods: The research is based on a composite design that triangulates from a theoretical model, a quantitative analysis and a qualitative analysis. (3) Results: Of the 7357 tweets in the sample, 72.32% were found to be retweets. Four content families were extracted: politics, education, messages to society and defense of occupational groups. The feelings expressed ranged along a continuum, from unity, admiration and support at one end to discontent and criticism regarding the health situation at the other. (4) Conclusions: The development of networked sociopolitical and technical measures that enable citizen participation facilitates the development of new patterns of interaction between governments and digital citizens, increasing citizens’ possibilities of influencing the public agenda and therefore strengthening citizen engagement vis-à-vis such situations.

A E. Crassipes is considered a problem in different aquatic ecosystems, due to its abundance could become a solution to design and build economic and efficient treatment plants, and especially for the production of biofuels such as bioethanol. The objective of this research is to design and implement a sustainable development process between phytoremediation and bioethanol production with E. crassipes, evaluating the incidence of chromium adhered to the biomass of this plant in the production of bioethanol. Materials and methods: A system was installed to evaluate the phytoremediation with E crassipes with water loaded with chromium, determining the effectiveness of this plant to remove this heavy metal even if it is alive in a body of water. After this process, we proceeded to bring the biomass loaded with chromium to bioreactors to evaluate the production of bioethanol, assessing three types of biomass, one without chromium adhered and the other two with chromium adhered to its plant structure. There was an impact of the ethanol production of the E crassipes due to the presence of chromium, but this production can be taken into account for the assembly of an integral system of phytoremediation and bioethanol production, making the most of this biomass.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Natural carotenoids are secondary metabolites that exhibit antioxidant, anti-inflammatory and anti-cancer properties. These types of compounds are in high demand by pharmaceutical, cosmetic, textile and food industries, leading to the search for new natural sources of carotenoids. In recent years, the production of carotenoids from bacteria has become of great interest for industrial applications. In addition to carotenoids with C40-skeletons, some bacteria have the ability to synthesize characteristic carotenoids with C30-skeletons. In this regard, a great variety of methodologies for the extraction and identification of bacterial carotenoids has been reported and this is the first review that condenses much of this information. To understand the diversity of these carotenoids, we present their biosynthetic origin in order to focus on the methodologies employed in their extraction and characterization. Special emphasis has been made on high-performance liquid chromatography-mass spectrometry (HPLC-MS) for the analysis and identification of bacterial carotenoids. We end up this review showing their potential commercial use of bacterial carotenoids. This review is proposed as a guide for the identification of these metabolites, which are frequently reported in new bacteria strains.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

The presence of azo dyes in textile effluents is an issue of major concern due to their potential impact on the environment and human health. In this study we investigate the photocatalytic degradation under visible light of Reactive Violet 5 (RV5), an azo dye widely used in the textile industry. A preliminary screening of different titania-based catalysts was carried out to identify the best candidate for RV5 removal. The selected catalyst was then tested in a stirred and aerated lab-scale reactor illuminated with a light LED source (λmax = 460 nm). The effects of pH, catalyst load and hydrogen peroxide additions on the efficiency of dye removal were evaluated. Under the best conditions (pH 10, 3 g/L of catalyst and 60 mM hydrogen peroxide), the dye solution was completely decolorized in about 2 h. Overall, the results obtained suggest that the proposed process may represent a suitable method for the removal of RV5 from textile effluents.

In the present work we study the properties of geodesic sub-$ (\alpha,b,s) $-preinvex functions on Hadamard manifolds and establish some basic properties in both general and differential cases. Further, we study sufficient conditions of optimality and proved some new inequalities under geodesic sub-($ \alpha,b,s $)-preinvexity.

This article is an effort to scrutinize the role of Information Technology development in the chronological transformation of Urban Planning domain using the exploratory research approach. In this research, it is argued that the theoretical and practical understanding of Urban Planning should absorb and integrate the bright outcome of the rise of Information and Technology to foster congruent future urban development. The article addresses the trends of transformation in the urban planning domain through the myopic lens of the expansion of information and communications technology era followed by investigating the key drivers shaping the interaction between modern-day urban planning and information technology considering both the dark and bright sides into account.

Environment pollution is one of the major problem that faces by our civilization . Textile industry is one of the factor for pollute the environment. In this study various causes that occurs by textile industry and pollute the environment will be shown and described. In textile industry for energy to run the factory various kind of fuel are used and in the industry there are many chemicals and dyes are used for the textile products. Plastic is one of the main substance for making the synthetic fabric. They pollute the air, water, soil and also they pollute the ecosystem of the various animals and destroy the ozone surface of the earth. For various kind of pollution that causes by textile industry the life of normal life hampered. They got ill and many time men and women lost their organs and sometimes they got attacked by various life taking illness.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity. Contrary to this are shell structures, which can bridge large spans with little material if designed according to the force flow. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behavior on a smaller scale by resolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is being developed in an ongoing research project. The basic analysis approaches which were implemented are presented in this paper. The basic workflow, the used programs and material models and their calibration on the tests on textile-reinforced concrete (TRC) samples are described.

All-polyamide composite coated fabric (APCCF) materials were developed and used as the material of construction of textile bioreactors as a replacement of traditional costly steel-/concreate-based bioreactors. Then, APCCF-bioreactor was used to cultivate filamentous fungus Neurospora intermedia to produce ethanol and fungal biomass. The results showed similar performance of the fungus cultivated in stain-less steel bioreactors. Techno-economical analysis for a 5000-m³ APCCF bioreactor for fermentation facility would lead to a reduction of the annual production cost of the facility by $128,000,000 compared to similar stainless-steel processes. The comparative analyses (including mechanical and morphological analyses, density measurements and techno-economical analysis) revealed that the APCCF is a better candidate for material of construction of the textile bioreactor. The APCCF is a 100% recyclable single polymer composite which was prepared from textile production line waste.

This study describes the development of an image-based insect trap diverging from the plug-in camera insect trap paradigm. In short, a) it does not require manual annotation of images to learn how to count targeted pests and, b) it self-disposes the captured insects, and therefore is suitable for long-term deployment. The device consists of an imaging sensor integrated with Raspberry Pi microcontroller units with embedded deep learning algorithms that count agricultural pests inside a pheromone-based funnel trap. The device also receives commands from the server which configures its operation while an embedded servomotor can automatically rotate the detached bottom of the bucket to dispose of hydrated insects as they begin to pile up. Therefore, it completely overcomes a major limitation of camera-based insect traps: the inevitable overlap and occlusion caused by the decay and layering of insects during long-term operation, thus extending the autonomous operational capability. We study cases that are underrepresented in literature such as counting in situations of congestion and significant debris using crowd counting algorithms encountered in human surveillance. Finally, we perform comparative analysis of the results from different deep-learning approaches (YOLO7/8, crowd counting, deep learning regression) and we open-source the code and a large database of Lepidopteran plant pests.

Vitamin E facilitates testicular development and semen quality in farm animal. And most research tends to investigate antioxidant roles of Vitamin E in reproductive health; some research also find potential non-antioxidant roles of Vitamin E. To further uncover the mechanism by which Vitamin E modulates reproductive health, the paper reviews specific function of Vitamin E and candidate genes involved in male reproductive performance promoted by Vitamin E. The review found that cell proliferation (PDPN, BMP, Myc, AMPKa, GSK3β, PPARγ, CDK4, CDK6, Ki67, PCNA, Cyclin A2, Cyclin B1, Cyclin B3, BLM, REL, KLHL25)-, cell apoptosis (BCL-2, Caspase 9, Bax)-, spermatogenesis (CatSper1, CatSper2, NDRG1, CYP26B1, FSCN3, FLNA, SPCS3, YBX3, RARS)-, hormone receptor (PGR, FSHR, AR)-related genes are the underlying key points. And two miRNAs, miR-107 and miR-493-3p, which mediate cell cycle process, are also identified in response to Vitamin E treatment. The paper paves the way for a comprehensive understanding about effect of Vitamin E on testis development and semen quality in domestic animals.

Sexual issues and treatment side effects are not routinely discussed with men receiving treatment for prostate cancer and support to address these concerns is not consistent across settings. This study evaluates a brief e-learning resource designed to improve sexual wellbeing support and examine its effects on healthcare professionals’ sexual attitudes and beliefs. Healthcare professionals (n=44) completed an online questionnaire at baseline which included a modified 12-item sexual attitudes and beliefs survey (SABS). Follow-up questionnaires were completed immediately after the e-learning and at 4 weeks. Data were analysed using one-way, repeat measures ANOVAs to assess change in attitudes and beliefs over time. Significant improvements were observed at follow-up for a number of survey statements including ‘knowledge and understanding’, ‘confidence in discussing sexual wellbeing’ and the extent to which participants felt ‘equipped with the language to initiate conversations’. The resource was seen as concise, relevant to practice, and as providing useful information on potential side effects of treatment. Brief, e-learning has potential to address barriers to sexual wellbeing communication and promote delivery of support for prostate cancer survivors. Practical methods and resources should be included with these interventions to support implementation of learning and long-term changes in clinical behaviour.

E-learning with many outstanding advantages in training has drastically changed the self-study process due to the ability to personalize and effectively meet the learning activities of learners. E-learning and building an e-learning environment are currently paying attention and being deployed in many universities in Vietnam with different scope and levels. Especially in the current period, when science and technology are developing, many applications of technology and technology products have been applied in the field of education, changing the way of teaching and learning activities, the practice of both lecturers and students. Big Data and Artificial Intelligence (AI) technologies have replaced people not only for manual labor but also for intellectual labor, including the teaching of teachers. Many software applications have been used to replace people in the transmission of knowledge, testing, and evaluation of training quality, especially E-learning online training programs. However, in Vietnam today, the output quality of these online training programs has not been highly appreciated compared to similar programs in the world. The cause of this situation is that the training, teaching, and learning are not effective. Therefore, in this article, I will give some analysis, evaluate the current teaching and learning methods and propose solutions to enhance the interaction and initiative in the teaching and learning process of lecturers and students to improve the quality of online training in the future.

Internet-led labour market has become so competitive forcing many organisations from different sectors to embrace e-recruitment. However, realising the value of the e-recruitment from a Requirements Engineering (RE) analysis perspective is challenging. This research is motivated by the results of a failed e-recruitment project conducted in military domain which is used as a case study in this research. After reviewing the various challenges faced in that project through a number of related research domains, this research focuses on two major problems which are the (1) difficulty of scoping, representing, and systematically transforming recruitment problem knowledge towards e-recruitment solution specification; and (2) the difficulty of documenting e-recruitment best practices for reuse purposes in an enterprise recruitment environment. In this paper, a Problem-Oriented Conceptual Model (POCM) with a complementary Ontology for Recruitment Problem Definition (Onto-RPD) is proposed to contextualise the various recruitment problem viewpoints from an enterprise perspective and to elaborate those problem viewpoints towards a comprehensive recruitment problem definition. The POCM and Onto-RPD are developed incrementally using action-research conducted on three real case studies: (1) Secureland Army Enlistment, (2) British Army Regular Enlistment, and (3) UK Undergraduate Universities and Colleges Admissions Service (UCAS). They are later evaluated in a focus group study against a set of criteria. The study showed that the POCM and Onto-RPD provide a strong foundation for representing and understanding the e-recruitment problems from different perspectives.

Despite the uptake of tobacco smoking declining in the UK, smoking is still the leading cause of preventable poor health and premature death. While improved approaches to smoking cessation are necessary, encouraging and assisting smokers to switch by using substantially less toxic non-tobacco nicotine products may be a possible option. To date few studies have investigated the rates of smoking cessation and smoking reduction associated with the free provision of electronic-cigarettes (e-cigarette) to smokers. In this study the Blu Pro e-cigarette was given to smokers for use in place of tobacco for 90 days. The rates of smoking abstinence and daily smoking patterns were assessed at baseline 30 days, 60 days and 90 days. The response rate was 87%. After 90 days, the complete abstinence rate was 36.5% from 0% at baseline. Frequency of daily smoking reduced from 88.7% to 17.5% (P<0.001) and median consumption of cigarettes/day from 15 to 5 (P<0.001). Median days per month participants smoked also dropped from 30 to 13 after 90-days (P<0.001). On the basis of these results there may be value in smoking cessation services and other services ensuring that smokers are provided with e-cigarettes at zero or minimal costs for at least a short period of time.

The contents of Education for Sustainable Development (ESD) should be included in teachers’ initial and advanced training programs. In order to determine the key competences for sustainability, creating a Sustainable Consciousness is one of the main foundations. However, there are not many empirical studies that deal with consciousness from education. In this context, e-portfolio appears as a tool that promotes reflection and critical thinking, key competences for consciousness development. This work intends to propose a categorization system to extract types of consciousness and identify trainee teachers’ levels of consciousness. For this research work, of an eminently qualitative nature, we have selected twenty-five portfolios of students in the last year of the School of Education at the University of Macerata (Italy). The qualitative methodological procedure followed allowed to deduce three bases that shape trainee teachers’ consciousness: thinking, representation of reality and type of consciousness. We concluded that the attainment of a Sustainable Consciousness in teachers requires activating and developing higher levels of thinking, as well as a projective and macrostructural representation of reality.

Clinical training in medical schools in Spain is performed by rotations in university hospitals. During these internships, students are expected to acquire and master basic procedural skills. However, the assessment tools available rarely check whether these skills are completely acquired by the students. We have used an e-portfolio to determine the optimal number of times the students need to repeat a procedure to be able to perform it independently. The results were compared with the actual performance during the internships. An e-portfolio collected qualitative information about the internships. Quantitative information was also requested about the number of times each clinical skill was performed. Later, a survey asked these students and their teachers the optimal number of times each skill should be repeated before it could be considered fully acquired. The questionnaire was answered by 98.6% of the students and 70.3% of their teachers. Out of the 21 clinical skills and procedures selected, both students and their tutors agreed in a similar optimal value in 16 of them; only in five of them, teachers thought that students needed a greater number of times than that selected by the students. When these optimal values were compared with the actual values recorded in the portfolio during the internships, it was found that about half of the clinical skills were carried out less frequently than expected, thus providing an important feedback about the internships. Quantitative information collected in portfolios reveals a moderate mismatch between students and tutors perceptions of their training needs.

For any odd positive integer $x$, define $(x_n)_{n\geqslant 0} $ and $(a_n )_{n\geqslant 1} $ by setting $x_{0}=x, \,\, x_n =\cfrac{3x_{n-1} +1}{2^{a_n }}$ such that all $x_n $ are odd. The 3x+1 problem asserts that there is an $x_n =1$ for all $x$. Usually, $(x_n )_{n\geqslant 0} $ is called the trajectory of $x$. In this paper, we concentrate on $(a_n )_{n\geqslant 1} $ and call it the E-sequence of $x$. The idea is that, we consider any infinite sequence $(a_n )_{n\geqslant 1} $ of positive integers and call it an E-sequence. We then define $(a_n )_{n\geqslant 1} $ to be $\Omega-$convergent to $x$ if it is the E-sequence of $x$ and to be $\Omega-$divergent if it is not the E-sequence of any odd positive integer. We prove a remarkable fact that the $\Omega-$divergence of all non-periodic E-sequences implies the periodicity of $(x_n )_{n\geqslant 0} $ for all $x_0$. The principal results of this paper are to prove the $\Omega-$divergence of several classes of non-periodic E-sequences. Especially, we prove that all non-periodic E-sequences $(a_n )_{n\geqslant 1} $ with $\mathop {\overline {\lim } }\limits_{n\to \infty } \cfrac{b_n }{n}>\log _23$ are $\Omega-$divergent by using the Wendel's inequality and the Matthews and Watts's formula $x_n =\cfrac{3^n x_0 }{2^{b_n }}\prod\limits_{k=0}^{n-1} {(1+\cfrac{1}{3x_k })} $, where $b_n =\sum\limits_{k=1}^n {a_k } $. These results present a possible way to prove the periodicity of trajectories of all positive integers in the 3x + 1 problem and we call it the E-sequence approach.

The majority of E-commerce transactions reveal private information such as customers' identities, order contents, and payment information during the transaction. Other personal information such as health conditions, religion, and even ethnicity may be also deduced. Even when deploying electronic cryptocurrencies such as Bitcoin, anonymity cannot be fully guaranteed. Also, many anonymous payment schemes suffer from possible double spending circumstances. E-commerce privacy is basically a difficult problem as it involves parties with concurring interests. Three major e-commerce requirements are highly difficult to resolve: anonymous purchase, anonymous delivery, and anonymous payment. This work presents a possible e-commerce system addressing all three anonymity requirements for electronic-items business on open networks. The system offers anonymous entities authentication mechanisms up to completing a fair anonymous e-commerce transaction. The system is based on deploying a physically clone-resistant hardware token for each relevant involved party. The tokens are made clone-resistant by accommodating a Secret Unknown Cipher (SUC) in each hardware-token as a digital PUF-like identity. A set of novel generic system-setups for units, protocols and e-commerce schemes is introduced. The proposed anonymization is basically attained by virtually-replacing relevant e-commerce entities by low-cost, unique and clone-resistant tokens/units using SUCs. The units act as trustable anonymous, authenticated and non-replaceable entities monitored by their acting users.

With the increasing demand for energy worldwide, researchers from different fields have been striving to improve the sustainability and proper utilization of energy resources. Passive radiative cooling, as a natural energy transport method, can achieve cooling without additional external energy input. This review provides a comprehensive examination of passive radiative cooling, including its fundamental theories and latest development. A particular emphasis is placed on the diverse range of fields where passive radiative cooling has been applied, notably including but not limited to construction and architecture. The current state of applications, potential challenges that may arise with wider adaption and promising research directions for each field are thoroughly discussed. This review underscores the universal applicability and feasibility of passive radiative cooling and contributes to its future development by identifying promising areas for further exploration.

The global increase in population, the phenomenon of climate change, the issue of water pollution and contamination, and the inadequate management of water resources all exert heightened strain on freshwater reserves. The potential utilization of the interfacial solar steam generation (ISSG) system, which utilizes photothermal conversion to generate heat on material surfaces for wastewater purification and desalination purposes, has been successfully demonstrated. Textile materials based ISSG devices, including (woven, nonwoven and knitting) fabrics and electrospinning membranes, exhibit distinct properties such as rough surface texture, high porosity, significant surface area, exceptional flexibility, and robust mechanical strength. These characteristics, combined with their affordability, accessibility, and economic viability for widespread implementation, make them extremely attractive for applications in SSG. In this review, a comprehensive analysis of emerging concepts, advancements and applications of textile materials (woven, nonwoven, and knitting) fabrics and electro-spun membranes in the ISSG for wastewater purification and desalination is highlighted. We also emphasize significant obstacles and potential prospects in both theoretical investigations and real-world implementations, aiming to contribute to future advancements in the domain of textile based materials interfacial evaporation in wastewater purification and desalination. Furthermore, the drawbacks and the challenges of ISSG systems are also highlighted.

In this study, ozone oxidation experiment was carried out for the removal of fluorescent whitening agent which is widely used in textile dyeing and paper industry. The stilbene fluorescent whitening agent has been industrialized since the earliest, and the amount of current production is the highest. Due to the characteristics of the fluorescent whitening agent that cannot be removed by conventional wastewater treatment methods, the fluorescent whitening agent in wastewater treatment has difficulty in using as recycled water in the process. Pre-treatment ozone oxidation experiment was conducted prior to the introduction of Membrane Bio Reactor (MBR) treatment process by converting biodegradable materials into biodegradable materials. The removal efficiencies of fluorescent whitening agents, a diaminostilbene disulfonic acid derivative by ozone oxidation were evaluated by UV254 Scan, COD, T-N and color using a synthetic wastewater sample (COD=433.0 mg/ℓ) and paper and paper mill wastewater (COD=157.2 mg/ℓ).

Background Apolipoprotein E (APOE) gene polymorphism has been implicated in the pathogenesis of various metabolic disorders, including type 2 diabetes mellitus (T2DM). Type 2 diabetes mellitus (T2DM) is a major public health concern worldwide, including in Pakistan. Cardiovascular problems linked with T2DM have a significant impact on people and society. The study's goal is to investigate the relationship between Apolipoprotein E (ApoE) genotypes, lipid profiles, and cardiovascular complications such as ischemic heart disease (IHD) and stroke. Methods: This study was carried out on 260 subjects, divided into control D1: Diabetics without cardiovascular issues. D2: Diabetics with heart disease. D3: Diabetics with stroke. D4: Diabetics with both heart disease and stroke. Anthropometric parameters (age, BMI) and risk factors (smoking, diabetes duration, hypertension) were assessed in all groups. Serum levels of TC, TG, LDL, HDL, VLDL, creatinine, BSF, and HbA1c were measured. Apolipoprotein E gene polymorphism was determined using PCR-RFLP. Results: Hypertension, BMI, and dyslipidemia, defined as elevated levels of total cholesterol, triglycerides, LDL, HDL, and VLDL, as well as uncontrolled hyperglycemia (elevated fasting blood sugar and glycated hemoglobin) in T2DM, were linked to vascular complications such as IHD and stroke. Hypertension was prevalent in 75.4% of the population, with greater rates among the elderly. Stage 2 hypertension was more prevalent in all age groups. Apolipoprotein E gene polymorphism was discovered, with genotypes 3/3, 4/4, 2/3, and 3/4 being the most prevalent. Genotype 3/4 was more common in diabetics who had IHD/stroke or both problems, whereas genotype 2/3 was linked to DM and stroke. Conclusion: It is concluded that BMI, hypertension, hyperglycemia, atherosclerosis, and dyslipidemia are linked with cardiovascular complications of type 2 diabetes. Apolipoprotein E gene polymorphism is associated with cardiovascular disease in diabetic patients by affecting the lipid profile.

Shiga-like toxin producing Escherichia coli (STEC) is a well-known cause of foodborne acute diarrheic diseases especially in children and the elderly. The potentially fatal complications associated with toxin production range from bloody diarrhoea and ischemic colitis to kidney failure, haemolytic-uremic syndrome (HUS) and colon perforation. We describe a case and literature review of STEC – induced colitis, highlighting the clinical features, and the necessary tools for the best diagnosis approach and management. Facing challenging differential diagnosis ranging from ischemic colitis, inflammatory bowel disease, to infectious process due to a pathogenic or opportunistic agent, we practiced a step-by-step exploration. Beginning with bacteriological investigation, imagistic screening, and colonoscopy, we could rule out some of initial suppositions and reach the final diagnosis, also considering the pathological results. Although antibiotics are not indicated in this pathology, our patient did receive antibiotics, given the risk of translocation and colon perforation, without associating any complications, as HUS or peritonitis. Detailed and rigorous investigations along with a multi-speciality team are required for a prompt medical support. Coping the symptoms and refraining from further complications are the mainstem of the treatment.

Urinary tract infections (UTIs) caused by Uropathogenic Escherichia coli (UPEC) are a serious healthcare concern that must be treated with appropriate antibiotic therapy. However, antibiotic resistance among UPEC strains is increasing, particularly among individuals with recurrent illness. The proliferation of Extended-Spectrum Beta-Lactamase (ESBL) generating UPEC, as well as the increase of UPEC strains that display resistance to several antimicrobial drugs, adds to the difficulty of managing UTIs. UPEC strain genetic variants have a significant influence in their capacity to resist antimicrobial agents and adapt to changing environments. Understanding the genomic landscape of developing UPEC strains is critical for understanding the genetic basis of their resistance. Furthermore, tracking these genetic strains is critical for identifying patterns of resistance spread, directing infection control efforts, and educating.

Serotonergic neurons constitute one of the main systems of neuromodulators, whose diffuse projections regulate the functions of the cerebral cortex. Serotonin (5-HT) is known to play a crucial role in the differential modulation of cortical activity related to behavioral contexts. Certain aspects of the 5-HT signaling framework hint at its potential role as a modulator of activity-dependent synaptic changes within the critical period of the primary visual cortex (V1). Cells of the serotonergic system are among the first neurons to differentiate and operate. During postnatal development, ramifications from raphe nuclei become massively distributed in the visual cortical area, remarkably increasing the availability of 5-HT for the regulation of excitatory and inhibitory synaptic activity. A substantial amount of evidence has demonstrated that synaptic plasticity at pyramidal neurons of the superficial layers of V1 critically depends on a fine regulation of the balance between excitation and inhibition (E/I). Therefore, 5-HT could play an important role in controlling this balance, providing the appropriate excitability conditions that favor synaptic modifications. In order to explore this possibility, the present work used in vitro intracellular electrophysiological recording techniques to study the effects of 5-HT on the E/I balance of V1 layer 2/3 neurons, during the critical period. Serotonergic modulation of the E/I balance has been analyzed on spontaneous activity, evoked synaptic responses, and long-term depression (LTD). Our results pointed out that the predominant action of 5-HT implies a reduction of the E/I balance. 5-HT promoted LTD at excitatory synapses while blocking LTD at inhibitory synaptic sites, thus shifting the Hebbian alterations of synaptic strength towards lower levels of E/I balance.

Vitamin E is a group of eight compounds divided into two subgroups: four tocopherols (α-, β-, γ-, and δ-) and four tocotrienols (α-, β-, γ-, and δ-). α-Tocopherol is considered the most biologically active form. This review paper summarizes the current knowledge and historical progression of vitamin E research, with particular emphasis on its role in animal nutrition. Early studies in the 1920s identified vitamin E’s role in preventing neonatal mortality in rats. Over the following decades, scientists discovered the compound’s chemical structure and its importance for the immune system, skin health, anti-inflammatory properties, hormonal balance, and other bodily functions. Production of vitamin E products has evolved, starting with isolating the vitamin from natural sources and advancing to synthesizing it with greater efficiency and standardized potency units. Early animal studies focused on reproductive health and growth disorders, but further research demonstrated the importance of vitamin E in preventing encephalomalacia in domestic fowl and muscular dystrophy in rabbits and other animals. Today, vitamin E is commonly used as a feed additive to meet animals’ requirements and assure immune function and overall health. Despite much knowledge on vitamin E’s role in animal nutrition, many questions remain unanswered, and current research aims to determine optimal supplementation levels, interactions with other nutrients, impacts on gene expression, cell signaling and communication, and effects of supranutritional dosages in livestock. Vitamin E has a long and fascinating history in scientific research, with significant advancements in understanding its chemical structure and biological activity. In animal nutrition, vitamin E continues to play an important role in improving animal health, and ongoing research will continue to expand our understanding of its benefits and mechanisms of action.

On Feb. 6^th, 2020, FDA implemented the enforcement priorities against all flavored, cartridge-based e-cigarettes other than menthol and tobacco flavors. This ban undermined the products’ attraction to vapers, so e-cigarette manufacturers added flavorants of other attractive flavors into tobacco-flavored e-cigarettes and re-established attractions. Both the sales of e-cigarettes and posts on social media suggested that the manufacturers’ strategies are likely “successful”. The re-established attraction causes not only a public health issue, but also threats to the health of individual vapers. Research has shown an increase in toxicity associated with the flavorants commonly used in flavored e-cigarettes that are likely added in tobacco-flavored e-cigarettes based on tobacco-derived and synthetic tobacco free nicotine, and these other flavors are associated with higher clinical symptoms not often induced by only natural traditional tobacco flavors. The additional health risks posed by the flavorants are pronounced even without considering the interactions of toxicology of the different tobacco flavorants, and more research should be done to understand the health risks thoroughly and to take proper actions accordingly for regulation of these emerging products.

The adoption of recycling and proper disposal techniques for electronic waste is crucial in advancing sustainable development. The traditional approaches of motivating people for collection of electronic waste are often insufficient due to inadequate methods reaching out, given incentives, calculating appropriate incentives associate to the task of gathering the electronic waste and a lack of transparency in the entire process. Insufficient collection of electronic waste could result in the release of numerous harmful substances into the environment. Prior research studies have been carried out to tackle the issue of electronic waste management in a broad sense. The findings of those studies indicated diverse strategies, each of which is relevant solely to a restricted range of electronic waste reprocessing circumstances. The current study has presented a proposed technique for incentivizing tasks and activities associated to collection of electronic waste through the adoption of vector space technique. Blockchain smart contact technology, has been used to implemented the strategy. The method used involves various well defined mapping of tasks, nature of activities, and their magnitude in order to derived an incentive. Some scenarios for the calculations of incentives are presented, and the findings reveals the based case is by utilizing weighting scale scheme where each tasks and activities are mapped to its associated inventive rather than providing fixed incentive values. Ethereum was used as digital token for each unit of incentive. This concept has contributed in encouraging personal accountability in the management of e-waste collection in order to cultivate sustainable behaviors for a long term solution.

Extended-spectrum β-lactamase (ESBL) mediating resistance in Enterobacterales is a global public health issue, especially in low-and middle-income countries (LMICs) such as Cameroon. ESBL-producing Enterobacterales reduce therapeutic options and lead to the use of last resort drugs such as carbapenems even in vulnerable populations like children under five years. This study aims at determining the phenotypic and genotypic characteristics of ESBL-producing Escherichia coli (ESBL-Ec) isolated from children under five years with and without diarrhoea in two health care facilities in Dschang. A cross-sectional study was conducted from 3 February to 19 May 2022 in two hospitals in the city of Dschang, Cameroon. Stool collected were cultured on Eosine Methylen Blue (EMB) medium. Enterosystem 18 R kit was used for bacterial identification. Evaluation of the resistance patterns and detection of ESBL production were performed with, the Kirby Bauer disk diffusion method and CHROMagar® ESBL medium, respectively. The genomic DNA of ESBL-Ec was extracted using the boiling method and subjected to conventional and multiplex PCRs for detection of blaSHV, blaCTX-M and blaTEM genes. Data were entered into ExcelTM 2016. Epi info and R software were used for statistical analyses with a p-value <0.05 considered statistically significant. Out of the 125 children enrolled, 67.2% (84/125) were colonized by E. coli. Among these, 57.14% (48/84) were colonized by ESBL-Ec. ESBL- Ec isolates showed high levels of resistance to amoxicillin-clavulanic acid (96.22%), cefotaxime (75.47%), ceftriaxone (73.58%), ofloxacin (67.92%), levofloxacin (56.6%) and ciprofloxacin (54.71%). Children aged between 1-3 years (47.62%, p=0.09) and those who had taken an antibiotic one week prior to collection (70.83%, p=0.04) had a higher prevalence of ESBL-Ec with statistical significance. The majority of ESBL-Ec isolates (52.83%; 28/53) were co-producers of blaCTX-M and blaTEM. Infection prevention and control measures coupled with antimicrobial stewardship strategies need to be strengthened to reduce emergence and dissemination of ESBL-Ec among this vulnerable population.

Background: In the 2022 National Youth Tobacco Survey disposable e-cigarette devices are shown to be the most widely used e-cigarette devices amongst U.S. youth. In this paper we report the results of research designed to estimate the prevalence of use of BIDI® Stick branded e-cigarettes amongst youth (aged 13 to 17), and under-age young adults (aged 18 to 20) in the U.S. Methods: Cross sectional online survey of a nationally representative sample of 1,215 youth (13 17 years) recruited via the IPSOS probability-based KnowledgePanel and 3,370 young adults aged 18 to 24 - amongst whom 1,125 were aged 18 to 20. Results: Amongst youth aged 13 to 17, 0.91% [95% CI: 0.44-1.68] or 190,000 [95% CI: 90,000-350,000] youth reported having ever used a BIDI® Stick branded product and 0.04% [95% CI: 0.00-0.38] or less than 10,000 youth reported currently using a BIDI® Stick branded product. Amongst those young adults aged 18 to 20, 3.90% [95% CI: 2.49-5.81] or 470,000 [95%CI: 300,000-700,000] reported having ever used a BIDI® Stick product whilst 0.60% [95% CI: 0.17-1.55] or 70,000 [95% CI: 20,000-180,000] reported they now use a BIDI® Stick product “every day” or “some days”. Conclusions: The low prevalence of youth and underage adult current use of the BIDI® Stick e cigarette suggests that this product is not responsible for the recent growth in the use of disposable e-cigarettes by youth within the U.S. as demonstrated by the 2022 National Youth Tobacco Survey.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

Metabolites are essential intermediate products in metabolism, and metabolism dysregulation indicates different types of diseases. Previous studies have shown that cigarette smoke dysregulated metabolites; however, limited information is available with electronic cigarette (E-cig) vaping. We hypothesized that E-cig vaping and cigarette smoking altered systemic metabolites, and we propose to understand the specific metabolic signature between E-cig users and cigarette smokers. Plasma from non-smoker controls, cigarette smokers, and e-cig users were collected, and metabolites were identified by UPLC–MS (Ultraperformance liquid chromatography-mass spectrometer). Nicotine degradation was activated by e-cig vaping and cigarette smoking with increased concentrations of cotinine, cotinine N-oxide, (S)-nicotine, and (R)-6-hydroxynicotine. Additionly, we found significant decreased concentrations in metabolites associated with tricarboxylic acid (TCA) cycle pathways in e-cig users verses cigarette smokers, such as: D-glucose, (2R,3S)-2,3-dimethylmalate, (R)-2-hydroxyglutarate, O-phosphoethanolamine, malathion, D-threo-isocitrate, malic acid, and 4-acetamidobutanoic acid. Cigarette smoking significant up-regulated sphingolipid metabolites, such as D-sphingosine, ceramide, N-(octadecanoyl)-sphing-4-enine, N-(9Z-octadecenoyl)-sphing-4-enine, and N-[(13Z)-docosenoyl]sphingosine, verses e-cig vaping. Overall, e-cig vaping dysregulated TCA cycle realted metabolites while cigarette smoking altered sphingolipid metabolites. Both e-cig and cigarette smoke increased nicotinic metabolites. Therefore, specific metabolic signature altered by e-cig vaping and cigarette smoking could serve as potential systemic biomarkers for early cardiopulmonary diseases.

In the recent century, the tourism industry and within it the tourism economy are one of the most important and fundamental sectors of engaged business. E-tourism can be used as a dynamic tool in up to date areas of informative information and tourism marketing will be considered as a suitable field for the tourism industry. The aim of this study was to investigate the relationship between climate change and the amount of revenues from the tourism industry relying on a tool called e-tourism, and informing and providing services through this way so that Iran can achieve a greater share of export of a single-product oil economy combined with economic growth and sustainable development goals. The method of this research is descriptive-analytical.

The purpose of this study is to find out the e-reputation management of the hotel industry, as well as the social media channels used as the tools of hotel e-reputation building. This study used a qualitative approach by analyzing the in-depth interviews with hotel marketing communication practitioners of 15 hotel companies in Bandung City. The findings identified that e-reputation is considered a crucial factor in determining hotel performance due to the change of customers’ behaviors today and identified also three types of e-reputation management activities implemented by hotel companies, such as online activities, offline activities, and online/offline activities. The results of this study have implications for the hospitality industry, as a reference for formulating their marketing strategies.