Oligonucleotide conjugates with boron clusters have found applications in different fields of molecular biology, biotechnology, and biomedicine as potential agents for boron neutron capture therapy, siRNA components, and antisense agents. Particularly, closo-dodecaborate anion represents a high-boron containing residue with remarkable chemical stability and low toxicity, suitable for the engineering of different constructs for biomedicine and molecular biology. In the present work, we synthesized novel oligonucleotide conjugates of closo-dodecaborate attached to the 5'-, 3'-, or both terminal positions of DNA, RNA, 2'-O-Me RNA, and 2'-F-Py RNA oligomers. For their synthesis, we employed click reaction with the azido derivative of closo-dodecaborate. The key physicochemical characteristics of the conjugates have been investigated using high-performance liquid chromatography, gel electrophoresis, UV thermal melting, and circular dichroism spectroscopy. Incorporation of closo-dodecaborate residues at the 3'-end of all oligomers stabilized their complementary complexes, while analogous 5'-modification decreased duplex stability. Two boron clusters attached to the opposite ends of the oligomer only slightly influence the stability of complementary complexes of RNA oligonucleotide and its 2'-O-methyl and 2'-fluoro analogs. On the contrary, the same modification of DNA oligonucleotides significantly destabilized DNA/DNA duplex but gave a strong stabilization of the duplex with RNA target. According to CD spectroscopy results, two terminal closo-dodecaborate residues cause a prominent structural rearrangement of complementary complexes with a substantial shift from B-form to the A-form of the double helix. The revealed changes of key characteristics of oligonucleotides caused by incorporation of terminal boron clusters, such as the increase of hydrophobicity, change of duplex stability, and prominent structural changes for DNA conjugates, should be taken into account for the development of antisense oligonucleotides, siRNAs, or aptamers bearing boron clusters. These features may also be used for engineering of developing NA constructs with pre-defined properties.

The precipitate phases often play an important influence on the corrosion resistance of 2205 Duplex stainless steel (DSS). In the presented paper, the microstructure and corrosion resistance in the hot-rolled and cold-rolled 2205 DSS aging for different time at 850 °C was investigated by XRD, SEM and potentiodynamic polarization. It has been found that the Chi(χ) phase and Sigm(σ) phase were precipitated in turn after aging treatment of hot-rolled and cold-rolled materials, but the precipitate amount in cold-rolled material is much more than that of hot-rolled samples. The corrosion resistance of the solution-annealed cold-rolled material is similar to the hot-rolled material, but the corrosion resistance of cold-rolled material with precipitate is weaker than that of hot-rolled material after aging treatment. Pitting initiates preferentially in the Cr-depleted region from σ phase in aged hot-rolled 2205, and severe selective corrosion occurs on sigma/ferrite interfaces aged for a long aged lime. However, the initiation of pitting corrosion may take place at the phase boundary, defect and martensite in the aged cold-rolled 2205. The σ phase is further selectively dissolved by electrochemical method to investigate the difference of microstructure and corrosion behavior in hot-rolled and cold-rolled 2205 duplex stainless steel.

Experimental quantification of retention factors related to post-fire strength as well as post-fire ductility of intentionally selected stainless steel grades applied in construction is the objective of research presented here. These steel grades are characterized by a two-phase austenitic-ferritic microstructure of the duplex type. In this context two mutually corresponding chromium-nickel-molybdenum steel grades have been subjected to analysis, namely X2CrNiMoN22-5-3 steel belonging to the standard duplex group (DSS 22% Cr) and X2CrMnNiN21-5-1 steel belonging to the lean duplex group (LDSS). The similarities and differences in the mechanical properties exhibited by these steel grades after effective cooling, following more or less prolonged simulated fire action conforming to several development scenarios, have been identified and indicated. The resistance of given steel grade to permanent structural changes induced by the heating program proved to be the critical factor determining these properties and resulting in many cases in increased susceptibility to brittle fracture.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

The skyrocketing growth in the number of Internet of Things (IoT) devices will certainly pose a huge traffic demand for fifth-generation (5G) wireless networks and beyond. In-band full-duplex (IBFD), which is theoretically expected to double the spectral efficiency of a half-duplex (HD) wireless channel and to connect more devices, has been considered as a promising technology to accelerate the development of IoT. To exploit the full potential of IBFD, the key challenge is how to handle network interference (including self-interference, co-channel interference and multiuser interference) more effectively. In this paper, we propose a simple yet efficient user grouping method, where a base station (BS) serves strong downlink users and weak uplink users and vice versa in different frequency bands, mitigating severe network interference. We aim to maximize a minimum rate among all users subject to bandwidth and power constraints, which is formulated as a highly nonconvex optimization problem. By leveraging inner approximation framework, we develop a very efficient iterative algorithm to solve this problem, which guarantees at least a local optimal solution. Numerical results are provided to show not only the benefit of using full-duplex raido at BS, but also the advantage of the proposed user grouping method.

Non-Orthogonal Multiple Access (NOMA) is the key technology promised to be applied in next-generation networks in the near future. In this study, we propose a multi-points cooperative relaying (MPCR) NOMA model instead of just using a relay as the previous studies. Based on the channel state information (CSI), the base station (BS) selects a closest user equipment (UE) and sends a superposed signal to this UE as a first relay node. We have assumed that there are N UEs in the network and Nth UE, which is farthest from BS, has the poorest quality signal transmitted from the BS compared other UEs. Nth UE received the forwarded signal from N-1 relaying nodes that are UEs with better signal quality. At the ith relaying node, it detect its own symbol by using successive interference cancellation (SIC) and will forward the composite signal to the next closest user, namely i+1th UE, and include an excess power which will use for energy harvesting (EH) intention at the next UE. By these, the farthest UE in network can be significantly improved. In addition, closed-form expressions of outage probability for users over both the Rayleigh and Nakagami-m fading channels are also presented. Analysis and simulation results performed by Matlab software which are presented accurately and clearly show that the effectiveness of our proposed model and this model consistents with the multi-access wireless network in future.

Cooperative Non-Orthogonal Multiple Access (NOMA) with Simultaneous Wireless Information and Power Transfer (SWIPT) communication can effectively improve the spectrum efficiency and energy efficiency of the wireless networks with extend coverage. An important design issue is to incentivize a relaying center user to participate in the cooperative process and achieve a win-win situation to both the BS and the center user. Some private information of the center users are hidden from the BS in the networks. We apply a contract theory-based incentive mechanism under such asymmetric information scenario to incentives center user to join the cooperative communication to maximize the BS profit utility and to guarantee the center user’s expect payoff. A match theory-based Gale-Shapley algorithm is proposed to obtain the optimal strategy with low computation complexity. Simulation results indicated the network performance of our proposed cooperative transmission is much better than the conventional NOMA transmission and the benefit utility of the BS with the stable match strategy is nearly close to the complete channel state information multi-users scenario while the center users get the satisfied expect payoffs.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

The studied Khanbogd pluton of peralkaline granite is located in southern Mongolia and occupies an area of ~1000 sq. km. Previously, two ring-shaped bodies were constructed in a flattened shape pluton. However, this shape was not used for the genesis of this pluton. A recent study of Landsat image showed a several elliptical intrusions in two bodies. Chemistry interpretation shows that each intrusion differs in ASI, CIPW norms, 87Sr/86Sri and δ18O isotopes. Elliptical intrusions, uplifted country rocks between them, and roof pendants suggest magma penetration along fractured country rocks. Furthermore, two adjacent intrusive bodies and undeformed host rocks at the front part of the pluton are consistent with underplating magmatic factors during duplex-type thrusting. This magma event is also supported by low of Sr, Ba, Eu and high of Th, U, Pb anomalies and a few amount of garnet crystals in the granites, implying vapor absent melt crystallization associated with underplating. Multiple melt sources, as well as from mantle and recycled sea floor rocks, are identified by ratio of 87Sr /86Sri and δ18O values. The low isotope values, the thrust nature and 295–286 Ma ages of the alkali granites, indicate an underplate magma evidenced during Permian rifting.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

Duplex and Super Duplex Stainless Steels are very prone to secondary phases formation related to ferrite decomposition at high temperatures. In the present paper the results on secondary phase precipitation in a 2510 Duplex Stainless Steel, heat treated in the temperature range 850-1050 °C for 3-30 minutes are presented. The precipitation starts at grain boundaries with a consistent ferrite transformation for very short times. The noses of the TTP curves are at 1000 °C for σ-phase and at 900 °C for χ-phase, respectively. The precipitation sequence involves a partial transformation of χ into σ, as previously evidenced in 2205 and 2507 grades. Furthermore, the experimental data were compared to the results of Thermo-Calc calculations.

Additive manufacturing (AM) or 3D printing of metals is gaining popularity due to its flexibility in fabricating parts with highly complex designs, as well as simplifying manufacturing steps and optimizing process times. In this investigation, 17-4 PH stainless steel was additively manufactured using Laser-Powder Bed Fusion (L-PBF), followed by functionalization through a DUPLEX treatment. This treatment involved a plasma-assisted nitriding process, followed by deposition of an arc-PVD c-Al0.7Cr0.3N hard coating. The microstructural modifications resulting from plasma nitriding (such as the formation of Fe2,3N and Fe4N, and the αN or expanded martensite phases), and the surface improvements with the c-Al0.7Cr0.3N coating on the 3D-printed 17-4 PH steel, are evaluated in comparison to conventionally manufactured 17-4 PH steel. These microstructural characteristics are correlated with the mechanical response of the treated surfaces. As a result of the plasma nitriding process, the hardness of the 3D-printed 17-4 PH SS increased by approximately 260%. The wear, measured through dynamic and static scratch-testing, was reduced by approximately 31%. This improvement was attributed to the modification of adhesive failure mechanisms, leading to a reduction in wear volume, improved coating adhesion, and enhanced scratch resistance.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

Relationship between the results of penile duplex doppler ultrasound (PDDU) and response to vardenafil was investigated in patients diagnosed with erectile dysfunction (ED). Data of 148 patients with ED were analysed retrospectively. Patients who did not respond to therapy were classified as Group I (n = 32), those responded partially were classified as Group II (n = 40) and complete responders were classified as Group III (n = 76). Age, comorbid diseases, vascular and penile pathology were compared among the three groups. While diabetes mellitus (DM) and dyslipedimia positivity adversely affect the response to treatment, the presence of hypertension (HT), peyronie's disease and priapism increase the therapeutic response to the treatment (p < 0.05). Arterial insufficiency was present in 20(30.3%), 25(37,9%) and 21(31.8%) of the patients in Group I, Group II and Group III, respectively (p = 0.001). Venous insufficiency was observed in 3(14.3%) patients in Group I and in 8(85.7%) patients in Group III (p = 0.001). Arterial/venous insufficiency was seen in 9(30%), 14(46.7%) and 7(23.3%) of the patients in Group I, Group II and Group III, respectively (p = 0.001). Response rate to treatment was highest in normal patients according to PDDU, followed by patients with venous insuffiency. Besides, it was found that DM decreased the response to treatment, whereas response was increased in cases with HT, priapism and Peyronie’s disease.

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

Malignancy is a fatal disease with an increasing incidence with each passing year, and the early diagnosis of malignancy can significantly improve the cure rate of patients, which has profound implications for saving patients' lives. The changes of miRNA are closely related to the occurrence of malignant tumors. The expression of miRNA in many malignant tumors is obviously different and unique from that in normal tissues. In this study, a strategy for amplifying microRNA (miRNA) signal was designed using duplex specific nuclease (DSN), which was then combined with Peptide nucleic acid (PNA) probe hybridization technology to prepare a sensitive and efficient paper-based lateral flow biosensor (LFB) for the detection of pancreatic cancer (PC) associated microRNA-10b. The performance evaluation results of the LFB showed that the detection limit of miR-NA-10b is 5 nM/mL, and carries demonstrated well specificity, stability, reproducibility. The biosensor prepared in this paper can provide accurate and rapid detection of miRNA-10b. The detection results play a guiding role in the early diagnosis of PC. Meeting the clinical need for largescale screening of individuals at high risk of PC. Providing new avenues to achieve early mass screening in individuals at high risk of PC.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

: Early and accurate detection of infectious diseases is a key step for surveillance, epidemiology, and control, notably timely disease diagnosis, patient management and follow-up. In this study, we aimed to develop hand-held ultra-fast duplex PCR assays coupled to amplicon detection by lateral flow (LF) immunoassay to deliver a rapid, and simple molecular diagnostic test for con-comitant detection and identification of the main Leishmania parasites encountered in Tunisia and the Old World. We selected two DNA targets to amplify L. major/L. tropica and L. infantum/L. tropica group of species DNAs, respectively. We optimized the experimental conditions of a du-plex ultra-fast PCR. The amplification is performed by a portable Palm convection PCR machine within 18 min and the products are detected by a LF cassette within 10 minutes. The test allows the identification of the infecting species according to the position and number of test lines re-vealed. Tested on a selection of DNAs of representative Leishmania strains of the three studied species (N=37), the ultra-fast duplex PCR-LF showed consistent, stable, and reproducible results. The analytical limit of detection of the test was 0.4pg for L. major, 4pg for L. infantum and 40pg for L. tropica.

It was recently studied how to achieve the optimal degrees of freedom (DoF) in a multi-antenna full-duplex system with partial channel state information (CSI). In this paper, we revisit the DoF of a multiple-antenna full-duplex system using opportunistic transmission under the partial CSI, in which a full-duplex base station having M transmit antennas and M receive antennas supports a set of half-duplex mobile stations (MSs) having a single antenna each. Assuming no self-interference, we present a new hybrid opportunistic scheduling method that achieves the optimal sum DoF under an improved user scaling law. It is shown that the optimal sum DoF of 2M is asymptotically achievable provided that the number of MSs scales faster than SNR^M, where SNR denotes the signal-to-noise ratio. This result reveals that in our full-duplex system, better performance on the user scaling law can be obtained without extra CSI, compared to the prior work that showed the required user scaling condition (i.e., the minimum number of MSs for guaranteeing the optimal DoF) of SNR^2M−1.

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.