Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal-organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (¯201) orientation peaks of -Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 x1018 cm-3 and mobility of ~770 cm2V-1s-1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance-voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 x1013 cm-2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV-1. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.

This study introduces a gate design that uses pass transistor switches and enables the implementation of all nec- necessary logic gates with a single structure. This gate design can be used for efficient circuit resizing and creating secure obfuscated circuits. This work also presents simulation results that demonstrate the effectiveness of the gate in performing various logic gate operations.

In the pursuit of energy-efficient spiking neural network (SNN) hardware, synaptic devices lev-eraging emerging memory technologies hold significant promise. This study investigates the ap-plication of the recently proposed HfO2/SiO2-based interface dipole modulation (IDM) memory for synaptic spike timing-dependent plasticity (STDP) learning. Firstly, through pulse measure-ments of IDM metal-oxide-semiconductor (MOS) capacitors, we demonstrate that IDM exhibits an inherently nonlinear and near-symmetric response. Secondly, we discuss the drain current re-sponse of a field-effect transistor (FET) incorporating a multi-stack IDM structure, revealing its nonlinear and asymmetric pulse response, and suggest that the degree of the asymmetry depends on the modulation current ratio. Thirdly, to emulate synaptic STDP behavior, we implement dou-ble-pulse-controlled drain current modulation of IDMFET using a simple bipolar rectangular pulse. Additionally, we propose a double-pulse-controlled synaptic depression that is valuable for optimizing STDP-based unsupervised learning. Integrating the pulse response characteristics of IDMFETs into a two-layer SNN system for synaptic weight updates, we assess training and classification performance on handwritten digits. Our results demonstrate that ID-MFET-based synaptic devices can achieve classification accuracy comparable to previously re-ported simulation-based results.

The research on the impact of excavation of underpass tunnels has already had certain results, but there is a lack of research cases of double-line highway tunnels with oblique angles underpass the existing railway tunnels, especially the method of determining the area of the impact of the dynamic and static loads of the new tunnels and existing trains to be enriched by considering them at the same time. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel with oblique angles underpass the Hurong Railway in Wanshoushan. By constructing a three-dimensional finite element model and simulating the application of static tunnel excavation load, dynamic blasting load and dynamic train operation load of the existing tunnel, the overall displacement of the existing tunnel and the settlement value of the bottom plate of the track surface by the static tunnel excavation load were analyzed. Then, the stresses, vibration speeds and displacements of the tunnel due to the dynamic blasting loads and the dynamic train operation loads were obtained. The results show that: the area of influence of the static loads of the new tunnel excavation on the existing tunnel is divided into three types of perturbations presenting strong, weak and slight; the area affected by the blasting dynamic load of new tunnel excavation is a circular domain with the datum point in the tunnel section as the center; the area affected by the dynamic load of train operation in the existing tunnel is an ellipse with the center of the track surface of the existing tunnel as the datum; there is an anomalous shape in the area affected by the blasting dynamic load of new tunnel excavation and the area affected by the dynamic load of train operation in the existing tunnel.

This paper presents the design and implementation of a multichannel bio-impedance spectroscopy system on field programmable gate arrays (FPGA). The proposed system is capable of acquiring multiple signals from multiple bio-impedance sensors, process the data on the FPGA and store the final data in the on-board Memory. The system employs the Digital Automatic Balance Bridge (DABB) method to acquire data from biosensors. The DABB measures initial data of a known impedance to extrapolate the value of the impedance for the device under test. This method offers a simpler design because the balancing of the circuit is done digitally in the FPGA rather than using an external circuit. Calculations of the impedance values for the device under test were done in the processor. The final data is sent to an onboard Flash Memory to be stored for later access. The control unit handles the interfacing and the scheduling between these different modules (Processor, Flash Memory) as well as interfacing to multiple Balance Bridge and multiple biosensors. The system has been simulated successfully and has comparable performance to other FPGA based solutions. The system has a robust design that is capable of handling and interfacing input from multiple biosensors. Data processing and storage is also performed with minimal resources on the FPGA.

Abstract— Flight Control System is an integrated avionics system equipped with the minimum required components for an autonomous flight. This paper focuses on the Hardware Design of the Flight Control System and presents specific details of the components and its interface. The system architecture is based on Field Programmable Gate Array and Digital Signal Processor. Employing these two processors in the flight control system would improve the Flight Control System performance in terms of fast sequential processing of high-level control algorithms. In addition to Field Programmable Gate Array and Digital Signal Processor, the flight control computer system will also make use of Global Positioning System and Micro Electro Mechanical System sensors. The project will be implemented using Altera’s System On Programmable Chip builder, currently known as Qsys – Platform Designer implemented in Quartus-II. The system employs Nios-II processor which is 32-bit soft-core embedded-processor architecture designed especially for the Altera’s family of Field Programmable Gate Array. From conceptualization to final design, this paper presents the functionality of the different modulus and complex interfaces employed in this Flight Control System.

In any region of a space, the gravitational field cannot be eliminated. The speed of light in a vacuum has never been observed and cannot be observed with current technology. Till now, only the speed of light in a gravitational field has been observed. It results in that all the observed speed of light are always being varied by the gravity. Here, it is presented that light could be dispersion in a gravitational field analogous to the dispersion of light in the Newtonian prism experiment. The relativistic mass density on the surface of a neutron star is on the level of 10¹⁷kg/m³ while on the surface of the Earth is only 10^-7kg/m³, the effect of the gravitational field acting on the speed of light by a neutron star is much larger than that by the Earth. Therefore, the dispersion of light in strong gravitational field could be generally observed from the image of a star and it should have been observed through the double-image gravitational lensing and the spectroscopic binary system. And, it should affect the observed numbers, spectrogram, size and distance of the celestial objects.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

The circular photogalvanic effect (CPGE) is the photocurrent generated in an optically active material in response to an applied ac electric field, and it changes sign depending on the chirality of the incident circularly polarized light. It is a non-linear dc current as it is second-order in the applied electric field, and for a certain range of low frequencies, takes on a quantized value proportional to the topological charge for a system which is a source of nonzero Berry flux. We show that for a non-interacting double-Weyl node, the CPGE is proportional to two quanta of Berry flux. On examining the effect of short-ranged Hubbard interactions upto first-order corrections, we find that this quantization is destroyed. This implies that unlike the quantum Hall effect in gapped phases or the chiral anomaly in field theories, the quantization of the CPGE in topological semimetals is not protected.

An orthogonal pore ('orthopore') is conceptually based on an electrolytic cell with a standard pore (the main or 'longitudinal' pore) between cis and trans compartments filled with electrolyte and augmented by a secondary or 'transverse' pore in the form of a channel that is perpendicular to and intersects the main pore. Orthopores can be designed at different scales: macro through micro to nano. With nano-sized pores an analyte (polymer) can be threaded through the main pore and exposed at the junction to electrolyte flow through the secondary pore. Polymer translocation speeds are then independent of the current measured, which can be of an arbitrary magnitude even with the polymer stationary. Orthopores have a wide range of potential applications, including polymer (DNA and protein) sequencing, DNA unzipping, logic circuitry, and protein identification. The present report shows how orthopores can be used to implement boolean logic.

In this paper, we study the effect of parasitic channel on electrical characteristics and power consumptions of vertically stacked gate-all-around (GAA) silicon nanosheet (NS) MOSFETs of the bulk and silicon-on-insulator (SOI) substrates. Through deliberate control of the bottom parasitic channel coverage, we systematically assess its influence on DC, AC, and RF characteristics including power consumption. The observed findings highlight a significant differentiation among the bottom parasitic channels: GAA (i.e., control sample with 100% coverage), omega-shaped gate NS (70% and 80% coverages), and FinFET (60% coverage). Compared with the device with a 60% coverage channel, the device with a 100% coverage channel possesses 3520% and 8030% normalized leakage current improvement for both NFET and PFET under the bulk substrate, respectively. Compared with bulk-substrate devices, the SOI-substrate devices further significantly improve the leakage current. Due to enhanced off-state current leakages in the 100% covered bulk-substrate device, the static power demonstrates a notable improvement (about 98.1%), compared to 60% covered devices. Hence, the utilization of a 60% covered channel will result in a degradation of both device and circuit performance. The observation of GAA NS MOSFET indicates that an increase in the bottom parasitic channel coverage ratio leads to a positive impact on power consumption and leakage currents. The examination presented here is useful in the fabrication of stacked GAA NS MOSFETs.

Deep learning methods have been widely used in PolSAR image classification. To learn the polarimetric information, many deep learning methods expect to learn high-level semantic features from original PolSAR data. However, only original data cannot learn multiple scattering features and complex structures for extremely heterogeneous terrain objects. In addition, deep learning methods always cause edge confusion due to the high-level features. To overcome these shortages, we propose a double-channel CNN network combined with an edge-preserving MRF model(DCCNN-MRF) for PolSAR image classification. Firstly, to combine complex matrix data and multiple scattering features together, a double-channel convolution network(DCCNN) is developed, which consists of a Wishart-based complex matrix and multi-feature subnetworks. The Wishart-based complex matrix network can learn the statistical characteristics and channel correlation well, and the multi-feature network can learn high-level semantic features well. Then, a unified network framework is designed to fuse two kinds of features to enhance advantageous features and reduce redundant ones. Finally, an edge preserving MRF model is designed to combine with the DCCNN network. In the MRF model, a sketch map-based edge energy function is designed by defining adaptive weighted neighborhood for edge pixels. Experiments are conducted on four real PolSAR data sets with different sensors and bands. Experimental results demonstrate the effectiveness of the proposed DCCNN-MRF method.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

Concrete is a very common construction material. As time prevails, cracks often appear in structures that pose a threat to strength and durability, which ultimately affect the structural integrity of concrete. Extensive work has been carried out in past on utilization of Carbon Fiber Reinforced Polymer (CFRP) as a repair material. But, this research particularly focuses on: multiple fiber layers i.e. single and double, traditional concrete mix ratio with locally available materials and varying flexural reinforcement. Furthermore, this work presents an experimental analysis to strengthen the Reinforced Concrete (RC) beams using SikaWrap- 230 C as a CFRP wrap, and Sikadur-330 as a bonding material. The comparison between single and double layers of CFRP is of major interest in this research. Six reinforced concrete beams were repaired with CFRP and tested under three-point bending test. For these specimens, load deflection behavior along with crack propagation and failure of beams were studied. Experimental results show that beams repaired using CFRP wrapping achieved higher flexural capacity and ductility as compared with reference beam. Moreover, results reveal that introduction of second layer of fiber caused around 4-5.2% increment in flexural strength and resulted in higher ductility of RCC beam.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Neonatal palliative care (NPC) is an integrated and holistic approach that is an integral part of the contemporary neonatal treatment delivery paradigm. It is the highest fulfillment of the notion of beneficence (doing or creating 'good') that has otherwise been neglected/underestimated by the focus of modern medicine on technology and instrumental treatments by its commitment to alleviating patient pain and quality of life. For decades, the Double-Effect Doctrine (DDE) has been used to consider and address a range of ethically questionable circumstances, often at the end of life, including euthanasia, termination of pregnancy to save maternal life, and morally justified warfare. The theory has continued to be mired in controversy as ethicists, legal scholars, theologians, and philosophers discuss the abstract concepts of moral reasoning, purpose, foresight, and other underlying moral theories. In this paper, the moral theory of DDE is discussed in its clinical application to the ethical decision-making process in neonatal palliative and end-of-life treatment, specifically 1) the administration of opioids as required for symptom control and 2) the use of palliative sedation for intractable symptom care.

A vehicle boom barrier gate system is one of the recently developed technologies operating at the entrances to the restricted areas. This paper aims to design and control of vehicle’s boom barrier gate system using robust augmentation technique. H 2 optimal and H infinity synthesis controllers are used to improve the performance of the system. The open loop response analysis of the vehicle boom barrier gate system shows that the input of the system need to be improved. Comparison of the vehicle boom barrier gate system with H2 optimal and H infinity synthesis controllers have been done to track a set point desired angular position using a step and operational open and close input signals and a promising results have been observed.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

Based on the definition of double fuzzy relations, two types of new rough set models are constructed, which are multi-granulation double fuzzy rough sets called optimistic and pessimistic multi-granulation double fuzzy rough sets, and some of their properties were studied. In addition, we study the relationship between optimistic and pessimistic multi-granulation double fuzzy rough sets and double fuzzy rough sets.

Discrete Double Hilbert Exponential sums along polynomials. This is preprint version (not peer reviewed) And we now check the proof of (ii) of Lemma 3.2 whether it is really true.

The aim of this article is introduced the concept of double framed T-soft fuzzy set (DFT-soft fuzzy set) which is the combination of soft set and fuzzy set. We also defined the notions and apply this concept in BCK/BCI-algebras. By using example, we also discussed the concept of double framed T-soft fuzzy algebra (DFT-soft fuzzy algebra) and double framed B-soft fuzzy algebra (DFB-soft fuzzy algebra) and also investigated their properties. Each double framed T-soft fuzzy algebra is double framed B-soft fuzzy algebra but by using example, we proved that converse may or may not be possible.

The fundamental challenge for the structural design of complicated shapes and lightweight structures such as Tensile Membrane Structures (TMS) is a reliable estimation of lateral loading such as wind load. Wind pressure coefficients can’t be correctly calculated by standards for a large range of intricate forms of structures. Computational Fluid Dynamics (CFD), a strong computational technique for evaluating wind pressure distribution on complicated geometry, can be used to determine wind-related parameters. The average wind related-distributions for the tensile membrane surface are validated with a few contributions from prior studies, which are important to validate with benchmarks in experimental wind tunnel experiments. For the double-curved surface, the results show good agreement between experimental tests and CFD simulations. In this study, CFD simulation was used to calculate the mean surface pressure coefficient (Cp) for generic shapes and tensile membrane forms using the steady Reynolds-Averaged Navier-Stokes (RANS) technique. Wind force coefficients and the effect of wind directions are also explored across a wide range of classical and tensile forms. The purpose of the current research is to look at the effect of wind assault angle on the Cp distribution for tensile membrane structures and general shapes.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

This paper presents a unified reconfigurable coordinate rotation digital computer (CORDIC) processor for floating-point arithmetic. It can be configured to operate in multi-mode to achieve a variety of operations and replaces multiple single-mode CORDIC processors. A reconfigurable pipeline-parallel mixed architecture is proposed to adapt different operations, which maximizes the sharing of common hardware circuit and achieves the area-delay-efficiency. Compared with previous unified floating-point CORDIC processors, the consumption of hardware resources is greatly reduced. As a proof of concept, we apply it to 1638416384 points target Synthetic Aperture Radar (SAR) imaging system, which is implemented on Xilinx XC7VX690T FPGA platform. The maximum relative error of each phase function between hardware and software computation and the corresponding SAR imaging result can meet the accuracy index requirements.

We present a case of a combination of two rare hereditary disorders: Аdrenal insufficiency, obesity, and red hair syndrome (OBAIRH) and Duchenne muscular dystrophy (DMD) in a boy. Both diseases were diagnosed during the first year of life. OBAIRH was suggested based on the ethnicity and family history of the patient, while DMD – based on an extreme increase in transaminase and CK levels during biochemical analysis of his blood.

Lead halide perovskite has become a promising candidate for high-performance photodetector (PD) applications due to its attractive optical and electrical properties such as high optical absorption coefficient, high carrier mobility, and long carrier diffusion length. However, the presence of highly toxic lead in these devices has limited their practical applications and even hindered their progress toward commercialization. Therefore, the scientific community has been committed to searching for low-toxic and stable perovskite-type alternative materials. Lead-free double perovskite materials, which are still in the preliminary stage of exploration, have achieved inspiring results in recent years. In this review, we mainly focused on two types of lead-free double perovskite based on different Pb substitution strategies, including A2M(I)M(Ⅲ)X6 and A2M(IV)X6. We reviewed the research progress and prospects of lead-free double perovskite photodetectors in the past three years. And more importantly, from the perspective of optimizing inherent defects in materials and improving device performance, we proposed some feasible pathways and made an encouraging perspective for the future development of lead-free double perovskite photodetectors.

This paper uncovers that quantum uncertain principle makes the single particle with global property have no certain path, and then wave of quantum particle can simultaneously do pass the double slits. The two subwaves after passing Young’s double slits are entanglement, they may form interference of subwaves. Consequently, we find a kind of quantum probabilistic entanglements with Wheeler's delayed choice. Quantum particles such as photons, electrons, neutrons, protons etc mean that wave of the quantum particle can simultaneously do pass through Young's double slits, rather than individual quantum particle may pass through Young's double slits at the same time. When considering wave property, we cannot consider particle property (Just as in the photoelectric effect, considering the particle nature of the system, people cannot consider wave property, otherwise the photoelectric effect cannot appear). Therefore, this paper discovers that the ability of single photon to hit electrons out in photoelectric effect is complementarily equivalent to the ability of wave of the single photon to simultaneously pass through Young's double slits in wave-particle duality. Objective criteria for distinguishing classical and quantum particles are discovered and objectively give the applicable realm of quantum mechanics for the first time. The crisis of the single particle’s simultaneously passing through Young's double slits, which has been plaguing physicists in the whole world up to now for decades, is solved, in which the studies are classified as classical and quantum particles, the classical particle and quantum particle wave cannot and can pass the Young’s slits, respectively. This paper discovers both the new physics mechanism of passing the double slits of the wave with the amplitude of 4-dimensional momentum representation wave function reflecting particle nature and the principle of self-adaptive emergence of wave-particle duality, and then using the principle, this paper gives both direct explanations to the current experiments and new predictions of new some experiments for wave-particle duality. All the deduced results here are consistent with all relevant physics experiments.

To study the influence of electrothermal effect of ESD protection device on the reliability of inte-grated circuit,a theoretical model of ESD protection device thermal resistance is constructed in the paper based on the Conservation of Energy Principle. By analyzing the temperature relativity between electricity parameter and thermology parameter of ESD protection device characterized by self-heating thermal resistance, the quantitative relationship expression of physical parameter and geometric parameter is obtained, which can be used to improve ESD protection device elec-tro-thermal effect. The simulation testing and the real tape-out testing of ESD protection device self-heating thermal resistance based on ggNMOS are shown and compared. It is concluded that self-heating thermal resistance is an effective index for the protection device electrothermal char-acterization. Based on the established model, the self-heating thermal resistance could be decreased to improve the homogeneity of the heat transference. The uneven distribution of device temperature can be reduced, and the overall reliability of chips can be improved.

A new kind of quantum gates, higher braiding gates, as matrix solutions of the polyadic braid equations (different from the generalized Yang-Baxter equations) is introduced. Such gates lead to another special multiqubit entanglement which can speed up key distribution and accelerate algorithms. Ternary braiding gates acting on three qubit states are studied in details. We also consider exotic noninvertible gates which can be related with qubit loss, and define partial identities (which can be orthogonal), partial unitarity, and partially bounded operators (which can be noninvertible). We define two classes of matrices, star and circle ones, such that the magic matrices (connected with the Cartan decomposition) belong to the star class. The general algebraic structure of the introduced classes is described in terms of semigroups, ternary and $5$-ary groups and modules. The higher braid group and its representation by the higher braid operators are given. Finally, we show, that for each multiqubit state there exist higher braiding gates which are not entangling, and the concrete conditions to be non-entangling are given for the obtained binary and ternary gates.

Market channel choice makes important contributions to the incomes and other livelihood attributes among smallholder farmers in developing countries. Often considered from a number of perspectives, the dominant view articulated suggests an advantageous integration into formal market channels. This position is questioned as it has implications for smallholder farmers’ food security and rural incomes. Using a mixed methods approach, the study collected primary data from 174 smallholder farmers and applied both a descriptive and multinomial logit regression model to analyze factors contributing to cocoyam production and market channel choices among respondents in the study area. Findings indicate that financial returns and available markets were key factors in cocoyam production, while amount received was a driver of market channel choice among 89% of respondents who sold directly at farm-gate. Farmers’ age (p=0.044), household size (p=0.043), distance to market (p=0.021), additional income (p=0.017) and amount received (p=0.014) were significant variables (p<.05) in the determinants of market channel choice. The study recommended improving market information provision and strengthening farmer associations which will enable smallholder farmers in rural communities to make informed choices with respect to produce price, access other markets and consolidate their collective market bargaining position.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

We compare two methods for creating a microfluidic device from an initial positive master with the same surface relief as the final device. The first method uses urethane or epoxy resin to create an intermediate master for PDMS casting. This method has a very low failure rate but a longer processing time. The second method utilizes PDMS double casting where the intermediate master is passivated PDMS. This method has a higher failure rate but a significantly shorter processing time. Detailed methodology for both methods is included along with a comparison of the strengths and weaknesses of each method. The resin intermediate is a simpler method while PDMS double casting is faster and more scalable. Ultimately it is found that PDMS double casting is preferable in most situations.

Cogging is a key part in the production process of superalloy, but inclusions affect the performance of superalloy. It is therefore particularly important to study the effects of cogging on the inclusions in superalloy. In our study, the superalloy GH4738 was made by double vacuum smelting. Cogging was performed by unidirectional drawing, upsetting and drawing, and upsetting/drawing with radial forging. The types and distributions of the inclusions after the three cogging processes were analyzed using scanning electron microscopy, energy dispersive spectroscopy, and software such as Image Pro Plus. The results showed that double vacuum smelting essentially determined the types of the inclusions in the GH4738 superalloy. Four types of inclusions were found in the experiments: TiC-TiN-Mo-S composite, TiC-TiN composite, Ce-Mo-S composite, and SiC inclusions. In the case of cogging by unidirectional drawing, the average size of the inclusions first decreased and then increased, from the center to the edge. In the case of upsetting and drawing, and upsetting/drawing with radial forging, the average size of inclusions decreased from the center to the edge.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

This work is devoted to the construction and study of commutative gates for a two-qubit quantum system. Using four-dimensional algebra developed by the Kazakh mathematician Abenov M.M. all groups of commutative gates have been constructed, and among all states of a two-qubit quantum system, unitary states with which a specific gate is connected have been identified. An explicit type of gate is described that transfers a quantum system from one unitary state to another unitary state. The proposed approach opens up new possibilities for the design of quantum algorithms not only for two-qubit quantum systems, but also for $n$-qubit quantum systems.

Video behavior recognition often needs to focus on object motion processes. In this work, a self-organizing computational system oriented to behavioral clustering recognition is proposed, which achieves the extraction of motion change patterns by binary encoding and completes motion pattern summarization using a similarity comparison algorithm. And in the face of unknown behavioral video data, a self-organizing structure with layer-by-layer accuracy progression is used to achieve motion law summarization by using a multi-layer agent design approach. Finally, the real-time feasibility is verified in the prototype system using real scenes to provide a new feasible solution for unsupervised behavior recognition and space-time scenes.

The problem of health status prediction of insulated-gate bipolar transistors (IGBTs) gains a lot of attention in the field of health management of power electronic equipment. The performance degradation of IGBT gate oxide layer is one of the important failure modes. In view of failure mechanism analysis and easy implementation of monitoring circuit, this paper selects the gate leakage current of IGBT as the precursor parameter of gate oxide degradation, and uses time domain characteristic analysis, gray correlation degree, Mahalanobis distance, Kalman filter and other methods to carry out feature selection and fusion, and finally obtains a health indicator characterizing the degradation of IGBT gate oxide. Based on the Convolutional Neural Network and Long Short-Term Memory (CNN-LSTM) network, this paper constructs an IGBT gate oxide degradation prediction model, and performs experimental analysis on the dataset released by NASA-Ames Laboratory, and the average absolute error of performance degradation prediction is as low as 0.0216. Compared with Long Short-Term Memory (LSTM), Convolutional Neural Network (CNN), Support Vector Regression (SVR) and CNN-LSTM models, CNN-LSTM network has the highest prediction accuracy. These results show the feasibility of gate leakage current as a precursor parameter of IGBT gate oxide layer failure, as well as the accuracy and reliability of the CNN-LSTM prediction model.

The theory of heavy ion double charge exchange (DCE) reactions proceeding by effective rank–2 isotensor interactions is presented. Virtual pion–nucleon charge exchange interactions are investigated as the source for induced isotensor interactions, giving rise to the Majorana DCE (MDCE) reaction mechanism. MDCE is of a generic character, proceeding through pairs of complementary (π±,π∓) reactions in the projectile and target nucleus. The dynamics of the elementary processes is discussed where the excitation of pion–nucleon resonances are of central importance. Investigations of initial and final state ion–ion interactions show that these effects are acting as vertex renormalizations. In closure approximation, well justified by the finite pion mass, the second order transition matrix elements reduce to pion potentials and effective two–body isotensor DCE interactions, giving rise also to two–body correlations in either of the participating nuclei. Connections to neutrinoless Majorana double beta decay (MDBD) are elucidated at various levels of dynamics, from the underlying fundamental electro–weak and QCD scales to the physical scales of nuclear MDBD and MDCE physics. It is pointed out that heavy ion MDCE reactions may also proceed by competing electro–weak charge exchange processes, leading to lepton MDCE by electrons, positrons, and neutrinos.

We present an investigation on the fracture of a mold, comparing it with a normal part using specific techniques, such as EDX, SEM, and AES. The EDX analysis revealed that the composition of the normal part was consistent with that of low carbon steel, mainly comprising Fe and C. In contrast, the fractured part exhibited cracks due to nonconforming nonmetallic inclusions and reticular carbides, with fractures resulting from microporosity agglomeration and cleavage fracture. The SEM and AES analyses further presented the causes of mold fracture, highlighting the mechanism by which dimples on the specimen edge contributed to the fracture. The EDX analysis confirmed that the mold experienced thermal brittleness during use. To enhance mold durability and extend its lifespan, a double-pulse electrodeposition method was employed to create a NiCo alloy coating as a replacement for the Cr layer on the metal surface. The coating exhibited a smooth and scratch-free surface. The prepared NiCo special coating significantly increased the mold yield strength by approximately 313.8%, facilitated a 13% increase in plastic deformation, and reduced fracture strain by 25%, effectively preventing mold fracture and 3improving its service life.

This paper presents the perturbation theory for the double–sine–Gordon equation. We obtain a system of differential equations that shows the amplitude and phase modulation of the approximate solution.. In the particular case λ = 0 we get the well-known perturbation theory for the sine–Gordon equation. For a special value λ=-1/8, we derive a phase-locked solution with the same frequency of the linear case. In general we obtain both coherent (solitary waves, lumps and so on) solutions as well as fractal solutions. We can demonstrate the existence of envelope wobbling solitary waves, because of the phase modulation depending on the solution amplitude and on the position. The main conclusion is that it is too reductive focus only on coherent solutions for the double sine-Gordon equation, because of the very rich behavior for the DSG nonlinear equation, including wobbling chaotic and fractal solutions.

Highly transparent thin films with the chemical formula BaSrMgWO6 were deposited by spin coating using a solution of nitrates of Ba, Sr and Mg and ammonium paratungstate in dimethylformamide with a ratio Ba:Sr:Mg;W=1:1:1:1. XRD, SEM, EDX and XPS investigations evidenced that an annealing at 800 ºC for 1h leaves the structure amorphous with a precipitate on the surface and that a supplementary annealing at 850 ºC for 45 min forms a nanocrystalline structure and dissolves a part of precipitates. It was evidenced a textured double perovskite cubic structure (61.9%) decorated with tetragonal and cubic impurity phases (12.7 %) like BaO2, SrO2 and MgO and an under-stoichiometric phase (24.4%) with the chemical formula Ba2-(x+y) SrxMgyWO5. From transmittance measurements the values of optical band gap were estimated for the amorphous (Eg= 5.15) and nanocrystalline (Eg=4.58 eV) phases. The presence of a lattice disorder was indicated by the high values of Urbach and weak absorption tail energies A decrease in their values was observed and attributed to the crystallization process and cation redistribution.

In this paper, the single event burnout(SEB) and reinforcement structure of 1200V SiC MOSFET (SG-SBD-MOSFET) with split gate and schottky barrier diode(SBD) embedded were studied. The device structure was established using Sentaurus TCAD, and the transient current changes of single event effect(SEE), SEB threshold voltage, as well as the regularity of electricfield peak distribution transfer were studied when heavy ions were incident from different regions of the device. Based on SEE analysis of new structural device, two reinforcement structure designs for SEB resistance were studied, namely the expansion of P+body contact area and the design of multi-layer N-type interval buffer layer. Firstly, two reinforcement schemes for SEB were analyzed separately, and then comprehensive design and analysis were carried out. The results showed that the SEB threshold voltage of heavy ions incident from the N+source region was increased by 16% when using the P+body contact area extension alone; When the device is reinforced with multi-layer N-type interval buffer layer alone, the SEB threshold voltage increases by 29%; The comprehensive use of P+body contact area expansion and multi-layer N-type interval buffer layer reinforcement increased the SEB threshold voltage by 33%. Overall, the breakdown voltage of the reinforced device decreased from 1632.935V to 1403.135V, which can be seen as reducing the remaining redundant voltage to 19%. The device performance was not significantly affected.

This paper presents a Modified Gate Diffusion Input (MGDI) design with four inputs for Quantum-dot Cellular Automata (QCA) technology. QCA is a promising nanotechnology that offers benefits such as low power consumption, and high density, making it a potential alternative to CMOS technology. The proposed planar cell design has advantages over previous designs, including a 19% reduction in the number of cells, a 29% reduction in total energy consumption, and a 44% reduction in average energy loss at the same occupancy level. The proposed block is capable of implementing 21 basic combinational functions and various sequential functions. The simulation of functions in 18nm technology and energy consumption calculation indicates that the resulting circuits have improvements of 41%, 27%, 27%, and 20% compared to multiplexers, comparators, four-bit parity circuits, and single-bit memory, respectively. Additionally, the number of cells in the proposed circuits has improved by 10%, 7%, 22%, and 19%, respectively.

The status of vegetation and the impacts of mammalian herbivores on rangelands are complex, and such studies in Kenya are scanty. We investigated the dynamics of ground cover vegetation in Hell’s Gate National Park in relation to mammalian herbivory. Removal of palatable vegetation is postulated to enhance the development of invasive plant species. We investigated the influence of mammalian herbivores on vegetation diversity and dynamics in this rangeland. Three sampling blocks approximately 3 Km apart measuring 100 m x 50 m were established, each divided into three belt-transects (100 m x 10 m), and separated by a 10 m buffer zone. 2 m by 2 m quadrats at 20 m intervals were established in each transect. We measured composition the richness of plant and mammal species, and herbivory levels four times for six months (September 2018 to February 2019). Plant cover (P&lt; 0.001) and species diversity (P&lt; 0.001) differed significantly among sampling blocks and between seasons (P&lt; 0.001). Non-metric multidimensional scaling of plant species and herbivores showed co-occurrence of Zebras with Sida tenuicarpa and giraffes with Solanum incunum. We conclude that the removal of preferred plants through herbivory may be giving an edge to invasive species in the park.

The gate resistance is a parasitic element in transistors for RF and millimeter-wave circuits that can negatively impact power gain and noise figure. To develop accurate device models, a reliable measurement methodology is crucial. This article reviews the standard measurement methodology used in the literature and proposes also an additional method, which is evaluated using suitable test structures in a 16nm FinFET process. The advantages and disadvantages of the two approaches are discussed along with their respective application scenarios

Two opposed p–n diodes are connected with another junction that causes cancellation of the electric field in the depletion layer of each diode by the field of the other diode. This derived quantum diode is called the A system. Another dual diode, constructed by the same process but with the p- and n-types positioned as duality, called the B system. When a bias voltage is applied between the A and B systems, Lorentz conservation imparts a momentum (i.e., a wave number) to the carriers in the absence of any internal voltage. Thus, a superconducting bias current density appears without the need for cooling. The reappearances of electron–hole pairs on the junction surfaces are assumed to be described by entire wavefunctions normalized by the band gap. Based on the bias superconducting current, NOT and NAND gates were constructed from the quantum diode systems. Numerical calculations revealed that the constant phases of the entire wavefunctions of the p-and n-types converged. Accordingly, it was clarified that Bose–Einstein condensation and the Meissner effect (described by the London equation) occurred in the quantum diode systems. Moreover, the systems exhibited rectification characteristics and a switching speed of the order of 10^-14 s. Combining this switching property with the large bias superconducting current (of the order of several V), we developed NOT and NAND gates with direct quantum correlations among many qubits, which are unaffected by random and thermal noises. These gates have memorization and initialization properties and are compatible with existing and accumulating programing algorithms. Moreover, when harvesting a divergent current output from these systems, the bias superconducting current and memorization property preserve the formed quantum correlations.

Few switching transitions in high power and medium voltage application of Power converters are desirable. The selective harmonics elimination (SHE) pulse width modulation offers a better quality waveform with lower switching transitions and hence lower switching losses. The SHE is a pre-programmed modulation technique where certain amounts of lower order harmonics are removed and fundamental voltage is controlled. After Fourier analysis of output waveform, a set of nonlinear transcendental equations is obtained which exhibits, multiple, unique or no solution in different range of modulation index (MI). In this paper, an iterative method based on the Jacobian estimate is proposed to solve a highly non-linear set of SHE equations. The proposed technique is easy in implementation and can solve a large number of such equations as computation of the Jacobian matrix in the subsequent iteration is estimated from the previous values. Moreover, the proposed method also removes the singularity problem, especially for large SHE equations. High accuracy in the initial guess is also not essential for this method and can converge to the solution with any random initial guess. The computational and simulation results are given to validate the concept. The hardware result is provided to confirm the computational and simulation results.

The role of initial state (ISI) and final state (FSI) ion–ion interactions in heavy ion double charge exchange (DCE) reactions A(Z,N)→A(Z±2,N∓2) are studied in the context of double single charge exchange (DSCE) reactions given by sequential actions of the isovector nucleon–nucleon (NN) T–matrix. The second order DSCE reaction amplitude is investigated in momentum representation in a formulation, focused on the extraction of nuclear matrix elements under the conditions of strong initial state (ISI) and final state (FSI) interactions. In closure approximation and using the momentum representation, the reaction amplitude is finally separated into ISI/FSI distortion coefficients and reaction kernels and nuclear matrix elements. The ISI/FSI reaction kernels emerge as the result of the repeated scattering on the avoided volume, introduced by the imaginary parts of the ion–ion optical potential and acting as sinks for the quantal probability current. The closure approximation allows derive a set of induced effective two–body isotensor interactions, given by products of spin–scalar, spin–vector central and rank–2 spin–tensor interactions. The intermediate propagator plays a key role in establishing correlation between the DCE transitions in the projectile and target nucleus. The presented approach emphasizes the special features of DSCE reaction dynamics as proceeding like a system of two coupled isospin dipoles whose strengths are determined by the momentum-space form factors of the NN isovector interaction. The properties of the DSCE interaction form factors are investigated and the approach is applied to data.

In this article, we first introduced new types of higher separation axioms called (r,s)-GFS-regular and (r,s)-GFS-normal spaces with the help of (r,s)-generalized fuzzy semi-closed sets (briefly, (r,s)-gfsc sets) and discussed some topological properties of them. Thereafter, we defined a stronger form of (r,s)-gfsc sets called (r,s)-g*fsc sets and investigated some of its features. Moreover, we showed that (r,s)-fsc set → (r,s)-g*fsc set → (r,s)-gfsc set, but the converse may not be true. In addition, we explored new types of fuzzy generalized mappings between double fuzzy topological spaces (U, τ, τ*) and (V, η, η*), and the relationships between these classes of mappings were examined with the help of some illustrative examples. Finally, some new types of compactness via (r,s)-gfso sets were defined and the relationships between them were introduced.

In this work, nitrite intercalated CaAl-LDH was firstly prepared in this work. Scanning electronic microscopy (SEM) coupled with the energy dispersive spectrometer (EDS) was used to characterize the morphology and element composition of the synthesized powder. Fourier transform infrared spectroscopy (FTIR) was used to characterize the chemical composition and X-ray diffraction (XRD) was used to analyze the structure. The nitrite release curve and the chloride concentration change curve were obtained to study the anion-exchange reaction. The corrosion protection effect of the CaAl-LDH loaded with nitrites towards the carbon steel was evaluated in 0.02 M NaCl solution by electrochemical impedance spectroscopy (EIS). Then the powder was added in the epoxy coating with a percentage of 2% (vs. epoxy resin). The coating morphology and roughness was evaluated by SEM and laser microscopy, and the corrosion protection effect was investigated by EIS in an immersion period of 21 d. Local electrochemical impedance spectra (LEIS) was used to characterize the corrosion development process in micro-corrosion sites. The corrosion product of the scratched area after salt spray exposure was analyzed by EDS and Raman spectroscopy. The corrosion protection mechanism of the CaAl-LDH loaded with nitrites was proposed based on the above experimental results.

In this paper, MgAl Layered double hydroxides (LDH) were synthesized by co-precipitation method using a colloid mill and characterized by XRD, IR and SEM. The LDHs was repeatedly tested and compared with different bearing lifetime tester in lithium base grease, and it was found that the environmental-friendly LDHs had greater performance than the traditional antioxidant, and it was the development direction of a new generation of environmental-friendly antioxidants in the future. By adding LDHs into large electric shovel greats (GRK-A) in open-pit coal mine, it can be seen by PDSC evaluation that the service lifetime of grease is extended by 20% while the overall performance of grease is not affected. With the increase of LDHs addition, the grease sample gets the greater activation energy, the stronger thermal oxidation and decomposition resistance. Comparing the energy storage modulus and flow transition index at different temperatures, it can be seen that adding the right amount of LDHs needs close attention for the system oxidation resistance and viscoelasticity. For the electric shovel grease system, the best oxidation resistance and rheological properties can be achieved by adding 2% of LDHs. The rheological viscosity-temperature curves show that the grease samples with different ratios of solid LDHs have better low-temperature properties than the mine grease.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

Considerable efforts have been made in recent years to identify an optimal treatment method for the removal of antibiotics from wastewaters. A series of supramolecular organic-inorganic magnetic composites containing Zn-modified MgAl LDHs and Cu-phthalocyanine as photosensitizer have been prepared with the scope to β-lactam antibiotics removal from aqueous solutions. The characterization of these materials confirmed the anchorage of Cu-phthalocyanine onto the edges of the LDH lamellae, with a negligible part inserted in the interlayer space. The removal of β-lactam antibiotics occurred via a concerted adsorption and photocatalytic degradation. The efficiency of the composites was depending on i) the LDH: magnetic nanoparticle (MP) ratio, that is strongly correlated to the textural properties of the catalysts, and ii) the phthalocyanine loading in the final composite. A maximum of the efficiency was achieved with a removal of ~93% of antibiotics after 2h of reaction.

Classical non-homologous end joining (NHEJ) is a molecular pathway that detects, processes and ligates DNA double-strand breaks (DSBs) throughout the cell cycle. Mutations in several NHEJ genes result in neurological abnormalities and immunodeficiency both in humans and mice. The NHEJ pathway is required for the V(D)J recombination in developing B and T lymphocytes, and for class switch recombination in mature B cells. Ku heterodimer formed by Ku70 and Ku80 recognizes DSBs and facilitates the recruitment of accessory factors (e.g., DNA-PKcs, Artemis, Paxx and Mri/Cyren) and downstream core factors subunits XLF, XRCC4 and Lig4. Accessory factors might be dispensable for the process depending on the genetic background and DNA lesion type. To determine the physiological role of Mri in DNA repair and development, we introduced frame-shift mutation in the Mri gene in mice. We then analyzed the development of Mri-deficient mice as well as wild type and immunodeficient controls. Mice lacking Mri possessed reduced levels of class switch recombination in B lymphocytes and slow proliferation of neuronal progenitors when compared to wild type littermates. Human cell lines lacking Mri were as sensitive to DSBs as WT controls. Overall, we concluded that Mri/Cyren is largely dispensable for DNA repair and mouse development.

Double burden of malnutrition (DBM) and anaemia is a growing concern in developing countries. 5,763 mother-child pairs were selected from a cross-sectional study (Bangladesh Demographic Health Survey, 2011) to examine DBM and anaemia in households. Overweight mothers had stunted (24.5%), underweight (19.8%), wasted (9.3%) and anaemic (51.7%) children. Region and drinking water were positively associated with both DBM and anaemia (p < 0.001). Father’s occupation and wealth index were positively associated with DBM (p <0.001) only. More policies and awareness programmes are needed to address the coexistence of child undernutrition and maternal overweight/obesity and anaemia in the same household.

A double Roman dominating function on a graph G is a function f : V(G) → {0, 1, 2, 3} 2 with the condition that every vertex u for which f(u) = 0 is adjacent to at least one vertex v for 3 which f(v) = 3 or two vertices v1 and v2 for which f(v1) = f(v2) = 2, and every vertex u for which 4 f(u) = 1 is adjacent to at least one vertex v for which f(v) ≥ 2. The weight of a double Roman dominating function f is the value w(f) = ∑u∈V(G) 5 f(u). The minimum weight over all double 6 Roman dominating functions on a graph G is called the double Roman domination number γdR(G) 7 of G. In this paper we determine the exact value of the double Roman domination number of the 8 generalized Petersen graphs P(n, 2) by using a discharging approach.

Reliable motor control design is a critical part of the electric vehicle application. Control techniques and motor control devices play an important role in achieving system reliability. In this study, motor control devices have been proposed to implement control techniques in sensorless PMSM. Motor control devices including PWM signal generation by FPGA, gate driver circuit (GDC), and power inverter were developed to be integrated into single-stage motor control devices for sensorless motor control applications. Improvements in GDC design have been the focus to increase the performance of the motor control devices used. Switching losses due to the parasitic elements caused ringing switching behavior of the power inverter circuit, which reduces the performance when the system is integrated. Moreover, in the implementation of sensorless motor control using observer techniques, these conditions affect the accuracy of rotor position estimation, which uses the current or voltage information of the power converter as a variable in the observer design model. Therefore, a GDC design using IR2110 with additional ringing suppression circuit configuration was proposed for the application of motor device control topology to improve the performance of sensorless motor control system. Furthermore, the reduction of switching losses, reduction of current distortion, and accuracy of rotor position information were confirmed by experimental results.

With the current technological transformation in the automotive industry, autonomous vehicles are getting closer to the Society of Automative Engineers (SAE) automation level 5. This level corresponds to the full vehicle automation, where the driving system autonomously monitors and navigates the environment. With SAE-level 5, the concept of a Shared Autonomous Vehicle (SAV) will soon become a reality and mainstream. The main purpose of an SAV is to allow unrelated passengers to share an autonomous vehicle without a driver/moderator inside the shared space. However, to ensure their safety and well-being until they reach their final destination, it is required an active monitoring of all passengers. In this context, this article presents a microphone-based sensor system that is able to localize sound events inside an SAV. The solution is composed of a Micro-Electro-Mechanical System (MEMS) microphone array with a circular geometry connected to an embedded processing platform that resorts to Field-Programmable Gate Array (FPGA) technology to successfully process in hardware the sound localization algorithms.

This work - in two parts - tries to promote a new method in Mathematical Modeling, not ever used before, namely the use of the methods of Non-standard Analysis in Topoi. For the general mathematical theory of topoi (Topoi Theory) we refer to the book [10] . For non-standard analysis in the particular Boolean topos SET (the category of sets) we refer to the book [11]. This first part of the work is related, from an applicative point of view, mainly with Mathematical Neuroscience, more precisely a model of the human thinking, consciousness and subconsciousness. The connections between brain and mind will be also scketched, but a closer study also need some further topics to be studied in Part II: Artificial Intelligence, namely (Quantum) neural networks and (Quantum) Turing machine. However both parts (I. and II.) should be considered together, because they complement each other. The topoi model the intuitionistic logic (multi-valued) and have been used in Quantum Physics (see [9] and its references) while Non-Standard Analysis in SET (introduced by Abraham Robinson[31]) has been applied in Mathematical Economics (see [2] and its references); however, the combination was never used until now in Applied Mathematics. Even more, the Non-standard Analysis in Topoi is not too much studied from the point of view of Pure Mathematics either. One of the main objective of this work is to produce progress in this aria of Mathematics also, mainly for the SET-type topoi and exponential topoi, those topoi used in Quantum Physics and in which we need Non-stantard Analysis for our purposes. Based on the paper [13] we propose the logic of non-standard extensions in topoi as a model of the human thinking (based on infons), these theories representing top and very difficult results in Abstract Mathematics. We will analise the relation between brain and mind via the genetic-epigenetic interplay. More details will be provided in the Introduction, followed by a short presentation of the general theory, later connected with the (Quantum) Yang-Baxter equations in topoi. The connections between these equations and braid groups and knots, with intended applications in Neuroscience and Artificial Intelligence will be further analysed in Part II. Besides promoting a new idea of modeling, the present paper aims to promote the building of a Research Proposal for the European $''$Human Brain Project$''$ (https://www.humanbrainproject.eu/en/), and the NSF-Europe Program $''$Collaborative Research in Computational Neuroscience$''$ (https://www.nsf.gov/funding/pgm\_summ.jsp?pims\_id=5147), jointly with the new founded $''$National Centre for the Research of the Brain$''$ of the Romanian Academy of Science (https://acad.ro/centreAR/CNCC/CNCC.pdf, in Romanian). $''$Blue Brain Project$''$ (https://www.epfl.ch/research/domains/bluebrain/) could also be of big interest. We hope that the journals edited by MDPI (Axioms, in particular) and by the Simion Stoilow Institute of the Romanian Academy - Revue Roumaine de Mathematique Pures et Appliqu (http://imar.ro/journals/Revue\_Mathematique/home\_page.html) - among others - will host special issues related to the research subjects described in both parts of this work, starting with this one. For further details and some of the progress on this research subject, see www.ovidiufpasarescu.com.}

The synthesis and structure of the 4,4′-dipyridyl N,N′-donor ligand with a central thiazolo[5,4-d]thiazole (tztz) unit, named Dptztz is presented. With the linker Dptztz and isophthalate (benzene-1,3-dicarboxylate, 1,3-BDC²⁻) the mixed-linker, two-dimensional coordination network [Zn(1,3-BDC)Dptztz]·DMF could be obtained (DMF = dimethylformamide), which belongs to the class of coordination polymers with interdigitated structures (CIDs). The incorporated DMF solvent molecules can be removed through solvent exchange and evacuation such that the supramolecular 3D packing of the 2D networks retains porosity for CO₂ adsorption in activated [Zn(1,3-BDC)Dptztz]. The first sorption study of a tztz-functionalized porous metal-organic framework material yields a BET surface of 417 m²/g from CO₂ adsorption. The heat of adsorption for CO₂ exhibits a relative maximum with 27.7 kJ/mol at adsorbed CO₂ of about 4 cm³/g STP which is interpreted as a gate-opening effect.

In this paper, we present a high-speed, unified elliptic curve cryptography (ECC) processor for arbitrary Weierstrass curves over GF(p), which to the best of our knowledge, outperforms other similar works in terms of execution time. Our approach employs the combination of the schoolbook long and Karatsuba multiplication algorithm for the elliptic curve point multiplication (ECPM) to achieve better parallelization while retaining low complexity. In the hardware implementation, the substantial gain in speed is also contributed by our n-bit pipelined Montgomery Modular Multiplier (pMMM), which is constructed from our n-bit pipelined multiplier-accumulators that utilizes DSP primitives as digit multipliers. Additionally, we also introduce our unified, pipelined modular adder/subtractor (pMAS) for the underlying field arithmetic, and leverage a more efficient yet compact scheduling of the Montgomery ladder algorithm. The implementation on the 7-series FPGA: Virtex-7, Kintex-7, and XC7Z020, yields 0.139, 0.138, and 0.206 ms of execution time, respectively. Furthermore, since our pMMM module is generic for any curve in Weierstrass form, we support multi-curve parameters, resulting in a unified ECC architecture. Lastly, our method also works in constant time, making it suitable for applications requiring high speed and SCA-resistant characteristics.

The stability issues in the widely known organic inorganic halide perovskite, CH3NH3PbI3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs2AgBiBr6 and Cs2TiBr6 is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide bandgap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, bandgap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

Structural hydroxide groups in layered magnesium-aluminum double hydroxides were partially replaced by fluoride ions. Fluorinated and fluorine-free materials were used as hosts for two dyes, carminic acid and hydroxyl naphthol blue, resulting in a hybrid pigment color palette. Additionally, the pigments were protected with a magnesium hydroxide phase to prevent the color from fading over time. The color properties of the pigments were significantly influenced by the host of dye, since the presence of fluorine directly influences the acid-base properties of the layered double hydroxides. Finally, the pigments were successfully applied to prepare colored creams.

The layered oxyselenide BiCuSeO has garnered significant interest because of its ability to exhibit low thermal conductivity and a high Seebeck coefficient. This study involved the preparation of Bi1−xNaxCuSeO1−xFx(x=0, 0.05, 0.10, 0.15, and 0.20) ceramics through the processes of high energy ball milling and cold isostatic pressing. A systematic study was conducted to investigate the impact of co−doping Na/F on the thermoelectric performance of BiCuSeO ceramics. Replacing Bi3+ with Na+ results in the introduction of a considerable amount of holes, leading to a notable enhancement in the electrical conductivity and power factor. The conductivity was significantly increased from 9.10 S cm−1 in the pure BiCuSeO to 94.5 S cm−1 in Bi0.85Na0.15CuSeO0.85F0.15 at 323 K. At 823 K, the power factor of the Bi0.85Na0.15CuSeO0.85F0.15 sample achieved 44.8×10−5 W/ m K2. Moreover, the Bi1−xNaxCuSeO1−xFx ceramics exhibit a minimum thermal conductivity of 0.43 W m−1 K−1. As a result, the Bi0.85Na0.15CuSeO0.85F0.15 sample achieves a maximum ZT value of 0.78, which is 7.09 times greater than that of the pure BiCuSeO sample (0.11) .

In the current study, a two-dimensional numerical study is carried out to investigate the performance of a novel Double-chamber Parallel Flexible Valves micropump, which utilized the electrowetting-on-dielectrics (EWOD) effect to drive the microfluid flow. By observing the flow fields, the internal circulations are seen on both the left and right side of the pump. The generation of the backflow is discussed by tracking the movement of the vortices. Only slight flow fluctuation is seen in the micropump. Based on the simulation outcomes, the structural parameters including the width of the inlet/outlet, the width of the pumping channel and the diverging angle in the micropump are analyzed, the influence of these parameters on the pumping volume and the maximum pressure have been discussed. Eventually, a group of optimal parameter combinations is given according to the results to extend the operating potential of the micropump.

We compare the well known Rayleigh-Ritz variational method (RRVM) with a recently proposed approach based on supersymmetric quantum mechanics and the Gram-Schmidt orthogonalization method (SSQMGS). We apply both procedures to a particular class of double-well harmonic oscillators that had been conveniently chosen for the application of the latter approach. The RRVM eigenvalues converge smoothly from above providing much more accurate results with less computational effort. Present results show that the unproved SSQMGS upper bounds do not hold.

This paper answers the need to plan a cost-minimizing charging schedule for electric buses and proposes a three-stage procedure, which is oriented around the participation of electric buses aggregator in a day-ahead energy auction. First, optimization models are provided to determine charging availability expressed as minimum and maximum hourly energy requirements taking into account detailed, minutely characteristics and constraints of the charging equipment and the buses. Next, the auction model is formulated by considering aggregated bids submitted by the electric buses aggregator once the charging availability is determined. Hence, the day-ahead prices reflect the optimal schedules of auction participants, and the bus aggregator is safe against peak-hour charging. Finally, hourly auction-based schedules are disaggregated into optimal minutely charging schedules. Mixed-integer linear programming models are formulated for aggregation-disaggregation stages investigated in this paper, while the variables and constraints introduced into the auction model are linear. The proposed methodology has been verified on a recently published case study of a real-world bus service operated on The Ohio State University campus. We show that the auction-based charging of all 22 buses outperforms as-soon-as-possible schedules by 7% to even 28% of daily cost savings. Using the aggregated bids, buses can flexibly shift charges between high- and low-price periods while preserving constraints of the charging equipment and timetables.

Mesoscale eddies, the weather system of the oceans, although being on the scales of O(20-100km), have a disproportionate role in shaping the mean jets such as the separated Gulf Stream in the North Atlantic Ocean, which is on the scale of O(1000km) in the along-jet direction. With the increase in computational power, we are now able to partially resolve the eddies in basin-scale and global ocean simulations, a model resolution often referred to as mesoscale permitting. It is well known, however, that due to grid-scale numerical viscosity, mesoscale permitting simulations have less energetic eddies and consequently weaker eddy feedback onto the mean flow. In this study, we run a quasi-geostrophic model at mesoscale resolving resolution in a double gyre configuration and formulate a deterministic parametrization for the eddy rectification term of potential vorticity (PV), namely, the eddy PV flux divergence. We have moderate success in reproducing the spatial patterns and magnitude of eddy kinetic and potential energy diagnosed from the model. One novel point about our approach is that we account for non-local eddy feedbacks onto the mean flow by solving the eddy PV equation prognostically in addition to the mean flow. In return, we are able to parametrize the variability in total (mean+eddy) PV at each time step instead of solely the mean PV. A closure for the total PV is beneficial as we are able to account for both the mean state and extreme events.

A field theoretic representation of the classical partition function is derived for a system composed of a mixture of anisotropic and isotropic mobile charges that interact via long range Coulomb and short range nematic interactions. The field theory is then solved on a saddle-point approximation level, leading to a coupled system of Poisson-Boltzmann and Maier-Saupe equations. Explicit solutions are finally obtained for a calamitic counterion-only system in proximity of a charged planar wall. The nematic order parameter profile, the counterion density profile and the electrostatic potential profile are interpreted within the framework of a nematic-isotropic wetting phase with a Donnan potential difference.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

Histone deacetylases inhibitors (HDACi) have shown promising therapeutic outcomes in haematological malignancies such as leu-kaemia, multiple myeloma and lymphoma, with dis-appointing results in solid tumours when used as monotherapy. As a result, combination therapies either with radiation or other deoxyribonucleic acid (DNA) damaging agents have been suggested as ideal strategy to improve their efficacy in solid tumours. Numerous in vitro and in vivo studies have demonstrated that HDACi can sensitise malignant cells to both electromagnetic and particle types of radiation by inhibiting DNA damage repair. Although the radiosensitising ability of HDACi has been reported as early as 1990s, the mechanisms of radiosensitisation are yet to be fully understood. This review brings forth the various protocols used to sequence the administration of radiation and HDACi treatments in the different studies. The possible contribution of these various protocols on the ambiguity that surrounds the mechanisms of radiosensitisation is also highlighted.

In this work, we present a study of ordinary muon capture (OMC) on 136Ba, the daughter nucleus of the 136Xe double beta decay (DBD). OMC rates to low-lying nuclear states (below 1 MeV of excitation energy) in 136Cs are assessed by using both the interacting shell model (ISM) and the proton-neutron quasiparticle random-phase approximation (pnQRPA). We also add the chiral two-body (2BC) meson-exchange currents and use an exact Dirac wave function for the captured s-orbital muon. OMC can be viewed as a complementary probe of the wave functions in 136Cs, the intermediate nucleus of the 136Xe DBD. At the same time OMC can be considered as a powerful probe of the effective values of the weak axial-type couplings in a 100-MeV momentum-exchange region relevant for the neutrinoless DBD. The present work represents the first attempt to compare the ISM and pnQRPA results for the OMC on a heavy nucleus by including also the exact muon wave function and the 2BC. Sensitivity estimates of the present and future neutrinoless DBD experiments will clearly benefit from the future OMC measurements through the OMC calculations similar to the present one.

Two extensions of the generalized double Lomax distribution are introduced - the spliced-scale generalized double Lomax distribution and the exponentiated generalized double Lomax distribution. Their properties are studied. Usefulness of the new distributions is shown by fitting them to stock returns datasets.

We investigate the dynamics and stationary states of a semiconductor exciton-polariton condensate in a double well potential. We find that upon the population build up of the polaritons by above-threshold laser pumping, coherence relaxation due to the phase fluctuations of the polaritons drives the system into a stable fixed point corresponding to a self-organized PT-symmetric phase.

Extensive experimental and theoretical research over the past several decades has culminated in the understanding of the mechanisms behind nanoparticle-mediated enhancements on the mechanical properties of hydrogels. This information is not only crucial to realizing applications that directly benefit from developing hydrogels with high mechanical strength, but also to guide the development of strategies to further enhance hydrogel properties by combining different approaches. In our study, we investigated the effect of combining two approaches – addition of nanoparticles and crosslinking two different polymers (to create double-network hydrogels) – on the mechanical properties of hydrogels. Our studies revealed that these approaches may be combined to synthesize hydrogel composites with enhanced properties; however, both polymers in the double-network hydrogel must strongly interact with the nanoparticles to fully benefit from the addition of nanoparticles. Moreover, the concentration of hydrogel monomers used for the preparation of the double-network hydrogels had a significant effect on the extent of nanoparticle-mediated enhancements; double-network hydrogel nanocomposites prepared using lower monomer concentrations showed higher enhancements in elastic moduli compared to those prepared using high monomer concentrations. Collectively, these results demonstrate that the hypotheses previously developed to understand the role of nanoparticles on the mechanical properties of hydrogel nanocomposites may be extended to double-network hydrogel systems and guide the development of next generation hydrogels with extraordinary mechanical properties through a combination of orthogonal approaches.

In this paper, we introduce and study the notion of rough I₂-lacunary statistical convergence of double sequences in normed linear spaces. We also introduce the notion of rough I₂-lacunary statistical limit set of a double sequence and discuss about some properties of this set.

A plasmonic refractive index (RI) sensor based on metal-insulator-metal (MIM) waveguide coupled with concentric double rings resonator (CDRR) is proposed and investigated numerically. Utilizing the novel supermodes of the CDRR, the FWHM of the resonant wavelength can be modulated, and a sensitivity of 1060 nm/RIU with high figure of merit (FOM) 203.8 is realized in the near-infrared region. The unordinary modes as well as the influence of structure parameters on the sensing performance are also discussed. Such plasmonic sensor with simple framework and high optical resolution could be applied to on-chip sensing systems and integrated optical circuits. Besides, the special cases of bio- sensing and triple rings are also discussed.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

Shape-shifting polymers are widely used in various fields such as intelligent switches, soft robots and sensors, which require both multiple stimulus response functions and qualified mechanical strength. In this study, a novel near infrared light (NIR) responsible shape-shifting hydrogel system was designed and fabricated, through embedding vinylsilane modified carbon nanotubes (CNTs) into particle-double network (P-DN) hydrogels by micellar copolymerization. The dispersed brittle Poly(sodium 2-acrylamido-2-methylpropane-1-sulfonate) (PNaAMPS) network of the microgels can serves as sacrificial bonds to toughen the hydrogels, and the CNTs endow it NIR photothermal conversion ability. The results show that the CNTs embedded P-DN hydrogels present excellent mechanical strength, i. e. fracture strength of 312 kPa and fracture strain of 357%. Moreover, an asymmetric bilayer hydrogel, where the active layer contains CNTs, can achieve 0°–110° bending deformation within 10 min under NIR irradiation and can realise complex deformation movement. This study provides a theoretical and experimental basis for the design and manufacture of photoresponsive soft actuators.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

Ionizing radiation-induced damage in cancer and normal cells leads to apoptosis and cell death, through the intracellular oxidative stress, DNA damage and disorders of their metabolism. Irradiation doses that do not lead to the death of tumor cells can result in the emergence of radioresistant clones of these cells, due to the rearrangement of metabolism and the emergence of new mutations, including those in the genes responsible for DNA repair. The search for the substances capable of modulating the functioning of the tumor cell repair system is an urgent task. Here we analyzed the effect of cerium(III) fluoride nanoparticles (CeF3 NPs) on normal (human mesenchymal stem cells – hMSCs) and cancer (MCF-7 line) human cells after X-ray radiation. CeF3 NPs effectively prevent the formation of hydrogen peroxide and hydroxyl radicals in an irradiated aqueous solution, showing pronounced antioxidant properties. CeF3 NPs are able to protect hMSCs from radiation-induced proliferation arrest, increasing their viability and mitochondrial membrane potential, and, conversely, inducing the cell death of MCF-7 cancer cells, causing radiation-induced mitochondrial hyperpolarization. CeF3 NPs provided a significant decrease in the number of double-strand breaks (DSBs) in normal cells, while in MCF-7 cells the number of γ-H2AX foci dramatically increased in the presence of CeF3 4 hours after irradiation. In the presence of CeF3 NPs, there was a tendency to modulate the expression of most analyzed genes associated with the development of intracellular oxidative stress, cell redox status and the DNA repair system after X ray irradiation. Cerium-containing nanoparticles are capable of providing selective protection of normal cells from radiation-induced injuries and are considered as a platform for the development of promising clinical radioprotectors.

Bone Scan Index (BSI) is an image biomarker for quantification on bone metastasis of cancers. To compute BSI, not only the hotspots (metastasis) but also the bones have to be segmented. Most related researches focus on binary classification on bone scintigraphy: having metastasis or none. Rare studies focus on pixelwise segmentation. In this study we compare three advanced convolutional neural network (CNN) based models to explore the bone segmentation on dataset in house. The best model is Mask R-CNN, which reaches the precision, sensitivity and F1-score: 0.93, 0.87, 0.90 for prostate cancer patients and 0.92, 0.86, 0.88 for breast cancer patients, respectively. The results are the average of 10-fold cross-validation, which reveals the reliability for clinical use on bone segmentation.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

In order to improve the operation performance of the multi-stage double-suction centrifugal pump and reduce the internal energy loss of the pump, this paper proposes a single-objective optimization design method based on non-hierarchical response surface model (RSM) and the multi-island genetic algorithm (MIGA). Nine parameters, such as the blade outlet width and blade wrap angle, were used as design variables, and the optimization objective was the efficiency under design conditions. In total, 149 sets of valid data were obtained under the latin hypercube sampling method (LHS), the corresponding thresholds were set for efficiency and head, and 99 sets of valid data were obtained. A cross-validation analysis of the sieved data was carried out based on non-hierarchical RSM, global optimization of the efficiency was carried out using MIGA, and numerical verification was carried out via CFD. The research results show that compared with hierarchical RSM, non-hierarchical RSM can approximate the nonlinear relationship between the objective function and the design variables with higher accuracy, and the model fitting R2 value was 0.919. The efficiency was improved by 3.717% after optimization. The overall prewhirl of the impeller inlet after optimization decreased, the internal speed of the volute significantly improved, the large-area vortex at the volute and the outlet pipe was eliminated, the impact loss at the volute separating tongue disappeared, and the overall hydraulic performance of the pump was improved. The total entropy output value of the optimized pump was reduced by 4.79 (W/K), mainly concentrated in the reduction in the entropy output value of the double volute, and the overall energy dissipation of the pump was reduced.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

The method of regularized stokeslets is widely-used to model microscale biological propulsion. The method is usually implemented with only the single layer potential, with the double layer potential being neglected, despite this formulation often not being justified a priori due to non-rigid surface deformation. We describe a meshless approach enabling inclusion of the double layer which is applied to several Stokes flow problems in which neglect of the double layer is not strictly valid: the drag on a spherical droplet with partial slip boundary condition, swimming velocity and rate of working of a force-free spherical squirmer, and trajectory, swimmer-generated flow and rate of working of undulatory swimmers of varying slenderness. The resistance problem is solved accurately with modest discretization on a notebook computer with the inclusion of the double layer ranging from no-slip to free slip limits; neglect of the double layer potential results in up to 24% error, confirming the importance of the double layer in applications such as nanofluidics, in which partial slip may occur. The squirming swimmer problem is also solved for both velocity and rate of working to within a few percent error when the double layer potential is included, but the error in the rate of working is above 250% when the double layer is neglected. The undulating swimmer problem by contrast produces a very similar value of the velocity and rate of working for both slender and non-slender swimmers, whether or not the double layer is included, which may be due to the deformation’s `locally rigid body’ nature, providing empirical evidence that its neglect may be reasonable in many problems of interest. Inclusion of the double layer enables us to confirm robustly that slenderness provides major advantages in efficient motility despite minimal qualitative changes to the flow field and force distribution.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

China is in the climbing phase of the "Inverted U" environmental Kuznets curve, from excessive environmental consumption to the development stage of governance and protection, and green innovation. It is the most complex period of environmental quality. Environmental and policy regulation are very important. Select panel data of 29 provinces of China (excluding Hong Kong, Macau, Taiwan, Hainan and Tibet) from 2008 to 2017, construct a nonlinear two-threshold regression model, empirically analyse the impact of environmental tax and government innovation subsidies to green processes innovation, and attempt to explore whether the implementation of these two policies at the same time can make enterprises more inclined to green process innovation and whether there is an optimal space for policy implementation. It is proposed that the synergy effect of environmental tax and government innovation subsidy policies on enterprise green process innovation should be fully utilized, and the enterprise green process innovation environment and incentive mechanism should be improved to promote the green transformation and sustainable development of enterprises.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

Suzuki cross-coupling reaction has developed one of the furthermost effectual approaches for the synthesis of biaryls or substituted aromatic moieties from aryl halides and arylboronic acids with a palladium-catalyst in the past two era’s. Herein, Pd-free layered double hydroxide containing nickel catalysts were prepared by co-precipitation method under ultrasonic irradiation and N2 atmosphere with different molar ratios of Ni: Mg: Al and coded as (1NiLDHs-Dr), (1.5NiLDHs-Dr) and (2NiLDHs-Dr). A series of reduced catalysts under 5%H2/N2 at different temperatures were coded as 1NiLDHs-R200, 1.5NiLDHs-R200 and 2NiLDHs-R200. As-synthesized 2NiLDHs-Dr was the superlative catalyst when coupling different aryl halides with different boronic acids derivatives. Deep investigation of all catalysts was done using different techniques such as inductively coupled plasma optical emission spectroscopy (ICP-OES), x-ray photoelectron spectroscopy (XPS), powder x-ray diffraction (XRD), thermogravimetric analyses (TGA), Fourier transfer infrared (FTIR), scanning electron microscope (SEM) connected with energy dispersive x-ray (EDX) and N2-physisorption at -196 ℃. The results attained verified that ɑ-Ni(OH)2 was fashioned for 2NiLDHs-Dr catalyst and the enclosure of nickel ions in the cationic sheet of layered structure were responsible for the fascinating catalytic efficacy rather than the basic nature of material. The Ni-containing LDHs catalysts encourage forthcoming studies in Pd-free catalyzed C-C coupling reactions.

Count data are used in many fields of practice, especially Poisson distribution as a popular choice for the marginal process distribution. If these counts exhibit serial dependence, a popular approach is to use a Poisson INAR(1) model to describe the autocorrelation structure of process. In this paper, the explicit formulas are proposed to evaluate performance characteristics of Double Moving Average control chart (DMA) for Integer valued autoregressive of serial dependence Poisson process. The characteristics of the control chart are frequently measured as Average Run Length (ARL) which means that the average of observations are taken before a system is signaled to be out-of-control. These proposed explicit formulas of ARL are simple and easy to implement for practitioner. The numerical results show that the DMA chart performs better than others when the magnitudes of shift are moderate and large.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The importance and near ubiquity of the Golden Ratio in disciplines like chemistry and biology is well known, but only recently has it come to light in areas pertaining to the Quantum domain. By using a modified tool-kit of hyper-complex numbers (known as Dimensional Gate Operators) and numerical analysis, we uncover a connection between hyper-dimensional objects, the Fibonacci sequence and that of quasiparticles and excitations. The results show that dimensionality increases in step with the Fibonacci sequence.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

This article conceptualises the link between firms’ value chains and distribution networks and the requirements for double materiality assessments in contemporary reporting regulations worldwide. The new European Sustainability Reporting Standards (ESRS) and the standards for sustainability reporting issued by the International Sustainability Standards Board (ISSB), called IFRS S1 and IFRS S2, require companies to report their own direct (scope 1) and indirect (scope 2) greenhouse gas (GHG) emissions as well as GHG emissions in their value chains and distribution networks (both scope 3). However, GHG emissions comprise just one dimension of information that is relevant to understand when assessing, managing and reporting the footprints and impacts of a firm and are, therefore, only a fraction of the key performance indicators (KPIs) related to ESG that should be disclosed. Through a case study, this article demonstrates the connection between the due diligence analysis of firms’ value chains and distribution networks, the analysis of the competitive parameters of the business model, the identified impacts, risks and opportunities, and the double materiality perspective. The double materiality perspective prioritises actions based on probability and significance, creating a natural space to identify KPIs. The article concludes by applying the REGS model and illustrating how it can assist firms in identifying relevant KPIs based on double-materiality assessments.

The extent of single and multi-cropping systems in any region, and potential changes to it, have consequences on food and resource use raising important policy questions. However, addressing these questions is limited by a lack of reliable data on multi-cropping practices at a high spatial resolution, especially in areas with high crop diversity. In this paper, we describe a relatively low-cost and scalable method to identify double cropping at the field-scale using satellite (Landsat) imagery. The process combines machine learning methods with expert labeling. We demonstrate the process by measuring double cropping extent in a portion of Washington State in the Pacific Northwest United States--- a region with significant production of more than 60 distinct types of crops including hay, fruits, vegetables, and grains in irrigated settings. Our results indicate that the current state-of-the-art methods for identifying cropping intensity---that apply rule-based thresholds on vegetation indices---do not work well in regions with high-crop-diversity. Our deep learning model was able to capture the diverse nuances and achieve a high accuracy (99\% overall accuracy and 0.92 Kappa coefficient). Our expert labeling process worked well and has potential as a relatively low-cost, scalable approach for remote sensing applications. The product developed here is valuable to inform several policy questions related to food production and resource use.

This study investigates via Lie symmetry analysis the Hunter-Saxton equation, an equation relevant to the theoretical analysis of nematic liquid crystals. We employ the multiplier method to obtain conservation laws of the equation derived from first-order multipliers. Conservation laws of the Hunter-Saxton equation, in combination with the Lie point symmetries of the equation, enable us to perform symmetry reductions through employment of the double reduction method. The method exploits the relationship between Lie point symmetries and conservation laws to effectively reduce both the number of variables and the order of the equation. Five nontrivial conservation laws of the Hunter-Saxton equation are derived, four of which are found to have associated Lie point symmetries. Applying the double reduction method to the Hunter-Saxton equation results in a set of first-order ordinary differential equations, the solutions of which represent invariant solutions for the equation.

In order to solve the interference of narrowband in the ultra-wideband (UWB) system, a high isolation of multiple-input multiple-output (MIMO) antenna is investigated in this paper. The MIMO antenna consists of 2 or 4 UWB elements; and each UWB antenna element is a monopole reconstructed with 2-notched slots, a U-shaped and inverted U-shaped slots etched on the monopole patch to achieve notch characteristics in WIMAX and ITU bands. The property of a 2-element MIMO antenna is analyzed firstly, which is put into a same substrate in parallel. Two rectangular branches are located in the middle to reduce the coupling. Then a 4-element MIMO antenna is studied to meet big size space and more application scenarios. Each element is placed orthogonally on the same substrate; and the isolation is implemented by a cross-shaped branch located in the middle of elements. Both MIMO antenna samples have been tested to verify the design. Measured results show that the working bandwidth is 2.45-14.88 GHz and 2.14-14.95 GHz, the isolation is greater than 17 dB and 20 dB, the peak gain is 5.7 dB and 5.9 dB, the max-imum radiation efficiency can reach 96% and 95%, the envelope correlation coefficient is less than 0.02 and 0.05 for the 2- and 4-element UWB MIMO antenna, respectively. They both are with very good omnidirectional characteristic with notched bands such as the WIMAX and ITU, and meet the requirements of the UWB application in most cases.