The influence of lignin modification on drug release and pH-dependent releasing behaviour of oral solid dosage form was investigated using three different formulations. The first formulation contains microcrystalline cellulose (MCC101) as excipient and paracetamol as active pharmaceutical ingredient (API). The second formulation includes Alcell lignin and MCC 101 as excipient and paracetamol, and the third formulation consists of carboxylated Alcell lignin, MCC 101 and paracetamol. Direct compaction was carried out in order to prepare the tablets. Lignin can be readily chemically modified due to the existence of different functional groups in its structure. The focus of this investigation is on lignin carboxylation and its influence on paracetamol control release behaviour at varying pH. Results suggest that carboxylated lignin tablets had the highest drug release, which is linked to their faster disintegration and lower tablet hardness.

Disposal and treatment of excess sludge is a huge problem in waste water treatment plants. Discharge plasma oxidation is an effective approach for sludge dewatering and digestion. In this study, the excess sludge disintegration by non-thermal discharge plasma coupled with thiosulfate (TSA) was investigated. The soluble chemical oxygen demand (SCOD) increased to 404.93 mg L-1 after 20 min of single discharge plasma treatment, and it further increased to 549.08 mg L-1 after adding 15 mmol L-1 of TSA; the water content of filter cake also further decreased in the presence of TSA. There existed an appropriate TSA dosage. In the discharge plasma coupled with TSA system, reactive oxygen species (·OH and ·O2-) were produced and played important roles in sludge disintegration. The addition of TSA promoted the production of ·OH. These reactive oxygen species destroyed the floc structures and promoted the transformation of organic substances, leading to reduction in average size of sludge flocs. The ratio of soluble extracellular polymer substances (S-EPS) was enhanced, while the ratio of tightly bound fraction was reduced after treatment. Thus, discharge plasma coupled with TSA promoted the lysis of microbial cells and released intracellular organic matter and bound water, finally improving sludge dewaterability.

The size and distribution of abrasive particles have a significant influence on the effectiveness of the cutting process by the high-speed abrasive water jet (AWJ). The paper deal with the abrasive materials disintegration intensity in AWJ cutting during the creation of the abrasive jet. An evaluation of the abrasive materials grabbed after forming in the cutting head was carried out and its grain distribution was evaluated. Used here the arithmetic, geometric and logarithmic method of moments and Folk and Ward method. The influence of abrasive concentration of abrasive materials as alluvial garnet, recycled garnet, corundum, and olivine on grain distribution was studied. A recovery analysis was also carried out and the recycling coefficient for each tested abrasive material was determined.

Due to rapid urbanization, the quantity of wastewater treatment plants (WWTP) has increased, and with it the amount of waste generated by them. Sustainable management of this waste can lead to the creation of energy-rich biogas through the fermentation process. This review presents recent advances in the anaerobic digestion process resulting in greater biogas production. Disintegration techniques for enhancing waste activated sludge fermentation can be generally partitioned into biological, physical and chemical, each of which are covered in this review. These disintegration techniques were compared mainly in terms of their biogas yield. It was found that ultrasonic and microwave disintegration provides the highest biogas yield (>500%); however, they are also the most energy demanding (>10,000 kJ kg-1 total solids).

Biocontrol strategies are gaining tremendous attention with the growing awareness of the irreparable harm caused by the continuous use of synthetic pesticides. This study examines the proteolytic and chitinolytic activities of Bacillus velezensis CE 100 and its termiticidal effect through cuticle degradation. The proteolytic and chitinolytic activities of B. velezensis CE 100 systematically increased with cell growth to the respective peak of 68.3, and 128.3 units/mL after seventh days of inoculation, corresponding with the highest cell growth of 16 x 107 colony forming units (CFU)/mL. The in vitro termiticidal assay showed that B. velezensis CE 100 caused a rapid and high rate of termite mortality with the median lethal time (LT50) of > 1h, and the highest mortality rate of 91.1% and 92.2% recorded at 11h and 12h in the bacterial broth culture and crude enzyme fraction, respectively. In addition to broken setae and deformed sockets, termites treated with the bacterial broth culture exhibited degraded epicuticles, while the crude enzyme fraction caused severe disintegration of both the epicuticle and endocuticle. These results indicate a tremendously higher prospect of B. velezensis CE 100 in the biological control of subterranean termites compared to the previously used entomopathogenic bacteria.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

There are numerous approaches to model an influence of manufacturing parameters on the dissolution and disintegration of solid dosage forms. A modern approach for modelling and simulating complex and heterogeneous systems such as pharmaceutical tablets focuses on computationally-intensive finite-element or discreet element methods. Industrial challenges such as Process Analytical Technology (PAT) and Quality by Design are stimulating computer-based technologies to design, control and improve the quality of pharmaceutical compacts and their performance. In this study the disintegration and dissolution model based on the numerical solutions of the Noyes-Whitney equation and cellular automata supported disintegration model are proposed and evaluated. The results from in vitro release studies of the mefenamic acid formulations were compared to the calculated release patterns from the tablet structures obtained from microtomography experiments and the purely algorithmically created virtual tablets.

For evaluating probabilities of arbitrary random events with respect to a given multivariate probability distribution, specific techniques are of great interest. An important two-dimensional high risk limit law is the Gauss-exponential distribution whose probabilities can be dealt with based upon the Gauss-Laplace law. The latter will be considered here as an element of the newly introduced family of (p,q)-spherical distributions. Based upon a suitably defined non-Euclidean arc-length measure on (p,q)-circles we prove geometric and stochastic representations of these distributions and correspondingly distributed random vectors, respectively. These representations allow dealing with the new probability measures similarly like with elliptically contoured distributions and more general homogeneous star-shaped ones. This is demonstrated at hand of a generalization of the Box-Muller simulation method. En passant, we prove an extension of the sector and circle number functions.