A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

The creation of a Europe-wide electricity market combined with the increased intermittency of supply from renewable sources calls for an investigation into the risk of aggregate peak demand. This paper makes use of a risk model to assess differences in time-use data from residential end-users in five different European electricity markets. Drawing on the Multinational Time-Use Survey database, it assesses risk in relation to the probability of electrical appliance use within households for five European countries. Findings highlight in which countries and for which activities the risk of aggregate peak demand is higher and link smart home solutions (automated load control, dynamic pricing and smart appliances) to different levels of peak demand risk.

In this paper, we study the performance of various deep reinforcement learning algorithms to enhance the energy management system of a microgrid. We propose a novel microgrid model that consists of a wind turbine generator, an energy storage system, a set of thermostatically controlled loads, a set of price-responsive loads, and a connection to the main grid. The proposed energy management system is designed to coordinate among the different flexible sources by defining the priority resources, direct demand control signals, and electricity prices. Seven deep reinforcement learning algorithms were implemented and are empirically compared in this paper. The numerical results show that the deep reinforcement learning algorithms differ widely in their ability to converge to optimal policies. By adding an experience replay and a semi-deterministic training phase to the well-known asynchronous advantage actor-critic algorithm, we achieved the highest model performance as well as convergence to near-optimal policies.

(1) Background: The purpose of this study was to investigate the relationship between IMO and burnout while assessing the contribution of job demands and resources on increasing internal orientation and worker well-being and, consequently, the levels of perceived performance; (2) Methods: Data were collected between April and December 2021 by completing an online questionnaire, developed in the Google Forms platform. The following descriptive statistics were analyzed: measures of central tendency (mean), dispersion (standard deviation), minimum value and maximum value. Next, Pearson's correlation coefficient was calculated to analyze the relationship between the variables under study.; (3) Results: The results showed the mediating effect of IMO between performance feedback and perceived performance, while burnout mediates the relationship between emotional and technology demands and perceived performance. (4) Conclusions: These conclusions demonstrate that constructive feedback might help a more efficient performance through better internal communication and the positive effects of technology demands could be the result of the interaction between personal and organizational resources.

The outbreak of SARS-COV-2 disease 2019 (COVID-19) abruptly changed the patterns in electricity consumption, challenging the system operations of forecasting and balancing supply and demand. This is due to the mitigation measures that include lockdown and Work from Home (WFH), which decreased the aggregated demand and remarkably altered its profile. Here, we characterise these changes with various quantitative markers and compare it with pre-COVID-19 business-as-usual data using Great Britain (GB) as a case study. The ripple effects on the generation portfolio, system frequency, forecasting accuracy and imbalance pricing are also analysed. An energy data extraction and pre-processing pipeline that can be used in a variety of similar studies is also presented. Analysis of the GB demand data during the March 2020 lockdown indicates that a shift to WFH will result to a net benefit for flexible stakeholders, such as consumer on variable tariffs. Furthermore, the analysis illustrates a need for faster and more frequent balancing actions, as a result of the increased share of renewable energy in the generation mix. This new equilibrium of energy demand and supply will require a redesign of the existing balancing mechanisms as well as the longer-term power system planning strategies.

The field of controlled polymerization is growing and evolving at unprecedented rates, facilitating polymer scientists to engineer the structure and property of polymer materials for a variety of applications. However, the lack of degradability, particularly in vinyl polymers, is a general concern for not only environmental sustainability but also biomedical applications. In recent years, there has been a significant effort to develop reversible polymerization approaches in those well-established controlled polymerization systems. Reversible polymerization typically involves two steps including (i) forward polymerization which converts small monomers into macromolecules, and (ii) depolymerization capable of regenerating original monomers. Furthermore, recycled monomers can be repolymerized into new polymers. In this perspective, we highlight recent developments of reversible polymerization in those controlled polymerization systems and offer insight into the promise and utility of reversible polymerization systems. More importantly, the current challenges and future directions to solve those problems are discussed. We hope this perspective can serve as an “initiator” to promote continuing innovations in this fairly new area.

The study investigated the changes that occurred in the Mexican power sector pre-, during, and post-COVID-19 pandemic and its repercussions on energy sustainability goals. The study is based on the variability of the installed capacity, consumption, generation, and demand of the National Electric System (SEN), covering the period from 2017 to 2021. The data were collected from the Development of the National Electric System (PRODESEN), the Ministry of Energy, the National Energy Balance, and the government's official website. The results indicated that in-stalled capacity and generation increased by 22.83% and 27.86%, respectively, despite the pan-demic. This growth was attributed to clean energy, mainly photovoltaic solar and wind sources. Another finding is that the gross domestic product (GDP), consumption, and demand were seri-ously affected by COVID-19. They had a fall of 8.2%, 2.2%, and 4.4%, respectively, which trans-lates into a significant economic lag and a slowdown in energy self-sufficiency and the Mexican Energy Transition (TEM). Moreover, the objective of generating 35% and 40% of electrical ener-gy through clean energy will be achieved by 2031 and 2035, instead of 2021 and 2035, respec-tively.

In this paper we compare the effects of forecasting demand using individual (disaggregated) components versus first aggregating the components either fully or into several clusters. Demand streams are assumed to follow autoregressive moving average (ARMA) processes. Using individual demand streams will always lead to a superior forecast compared to any aggregates, however we show that if several aggregated clusters are formed in a structured manner then these subaggregated clusters will lead to a forecast with minimal increase in mean-squared forecast error. We show this result based on theoretical MSFE obtained directly from the models generating the clusters as well as estimated MSFE obtained directly from simulated demand observations. We suggest a pivot-algorithm, that we call Pivot Clustering, to create these clusters. We also provide theoretical results to investigate sub-aggregation, including for special cases such as, aggregating MA(1) streams and ARMA streams with similar or same parameters.

Demand-Side Management (DSM) is an essential tool to ensure power system reliability and stability. In future smart grids, certain portions of a customer’s load usage could be under the automatic control of a cyber-enabled DSM program, which selectively schedules loads as a function of electricity prices to improve power balance and grid stability. In this scenario, the security of DSM cyberinfrastructure will be critical as advanced metering infrastructure and communication systems are susceptible to cyber-attacks. Such attacks, in the form of false data injections, can manipulate customer load profiles and cause metering chaos and energy losses in the grid. The feedback mechanism between load management on the consumer side and dynamic price schemes employed by independent system operators can further exacerbate attacks. To study how this feedback mechanism may worsen attacks in future cyber-enabled DSM programs, we propose a novel mathematical framework for (i) modeling the nonlinear relationship between load management and real-time pricing, (ii) simulating residential load data and prices, (iii) creating cyber-attacks, and (iv) detecting said attacks. In this framework, we first develop time-series forecasts to model load demand and use them as inputs to an elasticity model for the price-demand relationship in the DSM loop. This work then investigates the behavior of such a feedback loop under intentional cyber-attacks. We simulate and examine load-price data under different DSM-participation levels with three types of random additive attacks: ramp, sudden, and point attacks. We conduct two investigations for the detection of DSM attacks. The first studies a supervised learning approach, with various classification models, and the second studies the performance of parametric and nonparametric change point detectors. Results conclude that higher amounts of DSM participation can exacerbate ramp and sudden attacks leading to better detection of such attacks, especially with supervised learning classifiers. We also find that nonparametric detection outperforms parametric for smaller user pools, and random point attacks are the hardest to detect with any method.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

Background: Immersive and non-immersive VR technology has been increasingly employed in training. This has encouraged physicians working in skill development to try using it to improve the learning, emotional recognition, and social skills of various disorders. This study aimed to explore the controlled trials employing VR in autism, ADHD, and dyslexia. Methodology:A literature review has been conducted, on PubMed, Scopus, and Web of Science. Any controlled trial in the pediatric age group, involving the comparison of VR training with other types of therapies in autism, ADHD, and dyslexia was included. Results:Only four controlled trials were identified, comprising a total of 208 patients, with ages ranging from 6-16 years. Out of these studies, two involved patients with autism, one with ADHD, and one with dyslexia. VR was successful in improving emotional recognition but not social interaction in autism. All trials did not mention thoroughly possible complications of prolonged use of VR. Conclusion: Despite being a promising technology, there is still a long road to prove the validity of using VR in skills development. Few controlled trials have been tailored to explore VR advantages over conventional training and therapies, most of them have a limited sample size, a short training course, and no mention of possible setbacks, such as ocular effects and social isolation.

This work deals with the synthesis of bare and curcumin (CUR)-loaded chitosan (CS)-based macroparticles by ionic gelation using sodium hydroxide (NaOH) or sodium tripolyphosphate (TPP) as cross-linking agents. The resulting spherical-shaped macroparticles were studied using various characterization techniques, Scanning Electron Microscopy (SEM), Fourier Transformed Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). The release of CUR from the CS-based particles with respect to time was analyzed, and the encapsulation efficiency and degree of swelling were studied. All formulations showed excellent CUR trapping efficiency, exceeding 90%. In particular, the TPP-crosslinked macrobeads released 34 wt% of the charged CUR within minutes, while the remaining 66 wt% was released slowly due to the biodegradation of CS. The results indicate that the correct choice of gelling agent and its concentration leads to spherical particles capable of encapsulating CUR and releasing it in a wide range of kinetics depending on the specific application.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

Background: Overweight and obese adults seek effective exercise interventions to reduce accumulated fat, but the effectiveness of these interventions vary across studies. The purpose of this meta-analysis was to investigate the effectiveness of exercise interventions in overweight and obese adults based on measurement of accumulated fat distributions. (2) Methods: Databases were used to select eligible studies for this meta-analysis. Randomized controlled trials with a control and experimental group were included. Degrees of effectiveness of exercise interventions were computed to assess the benefits on reducing weight and subcutaneous, visceral, and ectopic fat accumulation. (3) Results: A total of twenty-one studies were included in this meta-analysis. Participation in exercise interventions showed beneficial effects in reducing weight and subcutaneous and visceral fat. The effectiveness of exercise interventions on ectopic fat accumulation could not be assessed due to the limited number of studies measuring ectopic fat. Additionally, effectiveness of exercise interventions that depended on measurements of accumulated fat varied. The average exercise intervention for overweight and obese individuals was moderate to vigorous intensity, 4 times per week, 50 minutes per session, and 22 weeks duration. (4) Conclusions: Participating in exercise interventions has favorable effects on reducing weight and accumulation of subcutaneous and visceral fat.

In this research, a new conceptual framework introduced to analysis of water security. Using the exponential, logistic growth model, and employing the historical population of Tabriz city from 1956 to 2016, the future period (2022-2100) population predicted. Pearson Correlation, Spearman's Rho and Kendall's rank coefficients were used for analyzing correlation between population and water consumption. In addition, the amount of city water demand in the future period predicted using the ordinary least square model. Then, water stress and water scarcity indices calculated for Tabriz city in the future period. Results indicated that the mathematical population growth models are very suitable for prediction of city population. There was a significant positive correlation between the city population and water demand. In addition, the amount of water demand will proportionally increase with rising number of population. Finally, linear and quadratic equations presented for city water demand based on the city population number. It can be concluded that Tabriz city will be faced with severe water stress in the future period. The proposed new method in this study can be used for other different cities of the world. Also, Results will be helpful for decision makers in optimum management of urban water resources.

The case for demand-driven research and development has received important considerations among governments, donors and programme implementing partners in development planning and implementation. Addressing demand is believed to be a bottom-top approach for designing and responding to development priorities and is good for achieving development outcomes. In this paper, we discuss the concept and application of demand driven research for development (DDRD) in Africa. We use evidence of six projects implemented under the BiomassWeb Project in Africa. We focus on parameters on level of engagement of stakeholders - whose demand is being articulated, the processes for demand articulation, capacity building and implementation processes, innovativeness of the project, reporting and sustainability of the project. We find that the nature of the institutions involved in articulation and implementation of demand-driven research and development projects and their partnerships influence the impact and reporting of demand-driven projects.

This study proposes a methodology for identifying time intervals in which time-of-use (ToU) energy tariffs can be set. This is achieved by analyzing the variability in electric power demand and esti-mating the potential for demand flexibility. The proposed methodology is as follows: first, data preprocessing is performed, focusing on the organization and cleaning of individual consumption records. Subsequently, the data are processed and classified by using consumption variability analysis and clustering techniques. Then, representative clusters are selected and time intervals are analyzed to identify periods of high electric power consumption variability. This methodology was tested with real data from smart meters in the Colombian electrical system, in which time intervals with potential for settinh ToU tariffs were ultimately identified. This work promotes the implementation of demand response strategies that enhance sustainability and facilitate the transition to a more resilient energy landscape both nationally and internationally. The findings are expected to contribute to the formulation of tariff schemes that encourage con-scious changes in electric energy consumption patterns.

In the traditional power system, customers respond to their primary electricity consumption pattern based on price or incentive to take additional advantages. By developing energy hubs (EHs) where electricity, heat, natural gas and other forms of energy are coupled together, all types of energy customers even the inelastic loads can participate in demand response (DR) program. This novel vision has led to the concept of "integrated demand response (IDR)". IDR programs (IDRPs) in EHs involve coordinating multiple DR activities across different energy systems, such as buildings, industrial complexes, and transportation networks. The main purpose of IDR is that multi-energy users can respond not only by shifting or reducing energy consumption from the demand side, but also by changing the type of energy consumed, in response to the dispatching center. The integration of IDRPs in EHs can help to reduce energy costs, improve grid stability, and increase the penetration of renewable energy sources (RES) in the power system. Moreover, by synchronizing DR activities across different energy systems, IDRPs can provide additional benefits, such as improved energy efficiency, reduced greenhouse gas emissions, and increased resilience to power outages and other disruptions. In this paper, we provide a review, assessment, and classification of fundamental principles, modeling techniques and optimization methods for IDR programs in EHs.

Background: Clean cookstove interventions can theoretically reduce exposure to household air pollution and benefit health, but this requires near-exclusive use of the stoves, with simultaneous disuse of traditional stoves. Previous cookstove trials have reported low adoption of new stoves and/or extensive continued traditional stove use. Methods: The Household Air Pollution Intervention Network (HAPIN) trial randomized 3195 pregnant women in Guatemala, India, Peru, and Rwanda either to a liquefied petroleum gas (LPG) stove and fuel intervention (n = 1590) or to control (n = 1605). The intervention consisted of an LPG stove and two initial cylinders of LPG, free fuel refills delivered to the home, and regular behavioral messaging. We assessed intervention fidelity (delivery of the intervention as intended) and adherence (intervention use) through the end of gestation, as relevant to the first primary health outcome of the trial: infant birth weight. Fidelity and adherence were evaluated using stove and fuel delivery records, questionnaires, visual observations, and temperature-logging stove use monitors (SUMs). Results: 1585 women received the intervention, at a median (interquartile range) of 8.0 (5.0–15.0) days post-randomization and gestational age of 17.9 (15.4–20.6) weeks. Over 96% reported cooking exclusively with LPG at two follow-up visits during pregnancy. Less than 4% reported ever running out of LPG. Complete abandonment of traditional stove cooking was observed in over 67% of intervention households. 31.4% removed their traditional stoves upon receipt of the intervention, and among those who retained traditional stoves, the majority did not use them: traditional stove use was detected via SUMs on a median (interquartile range) of 0.0% (0.0%, 1.6%) of follow-up days (median follow-up = 134 days). Conclusions: Fidelity of the HAPIN intervention, as measured by stove installation, timely ongoing fuel deliveries, and behavioral reinforcement as needed, was high. Exclusive use of the intervention during pregnancy was also high.

The prevalence of obesity or metabolic syndrome is increasing worldwide (“Globally metabodemic”). Approximately 25% of adult general population is suffering from nonalcoholic fatty liver disease (NAFLD) which has become serious health problem. Hepatic fibrosis is the most significant determinant of all cause and liver -related mortality in NAFLD. Noninvasive test (NIT) should be urgently required to evaluate hepatic fibrosis in NAFLD. Fibrosis-4 (FIB-4) index is the 1st triaging tool for excluding advanced fibrosis because of its accuracy, simplicity, and cheapness especially for general physicians or endocrinologists, although FIB-4 index has several drawbacks. Accumulating evidence has suggested that vibration controlled transient elastography (VCTE) and the enhanced liver fibrosis (ELF) test may become useful as the 2nd step after triaging by FIB-4 index. The leading cause of mortality in NAFLD is cardiovascular disease (CVD), extrahepatic malignancy, and liver-related diseases. NAFLD often complicates chronic kidney disease (CKD), resulting in increased simultaneous liver kidney transplantation (SLKT). FIB-4 index could be a predictor of not only liver-related mortality and incident hepatocullar carcinoma (HCC) but also prevalent and incident CKD, CVD, and extrahepatic malignancy. Although NITs as milestones for evaluating treatment efficacy have never been established, FIB- 4 index is expected to reflect histological hepatic fibrosis after treatment in several longitudinal studies. We here review the role of FIB-4 index as 1st step NIT in management of NAFLD.

Development of early math skills is linked to future success in mathematics and other academics. Educational videogames have been shown to promote academic achievement; however, few rigorous studies have evaluated the use of educational videogames in supporting math development, especially in early primary education. In the current study, an open-label randomized controlled trial was conducted involving 134 first grade students to determine, using standardized assessments, the impact of the educational mathematics tablet-based videogame, Knowledge Battle, on math scores and self-competency. Overall, Knowledge Battle did improve math skills in participants who played the game. Among those with lower pre-game math skills, the Knowledge Battle group’s mean math score increased more than the control group’s mean math score (9.7 vs. 6.0; p=0.02). There was no association between perceived sense of self-competency and total math score (p=0.8141). However, players who had a higher sense of self-competency were more likely to enjoy playing the game. In conclusion, our findings suggest that Knowledge Battle was an acceptable and enjoyable educational mathematical videogame for first grade students, and may be most impactful for those with low math skills.

This paper aims to explore how climate change affects electricity generation (fossil-fueled power plants, hydroelectric stations, wind systems and photovoltaics) and energy demand in residential buildings in Greece for the period up to 2050. In both cases RCP scenarios results are considered in the appropriate spatial and temporal dimension. Energy supply technologies were examined through statistical regression models and/or mathematical equations correlating climatic parameters with energy productivity. With respect to energy demand, bottom-up models were developed that integrate behavioral and policy aspects. The analysis showed that climate change is expected to mainly affect electricity generation from hydro and thermal power plants, while the impacts on solar and wind energy are significantly lower. The range of impacts on hydro potential and electricity generation depends on the geographical location of the power plants and shows significant uncertainty due to the corresponding uncertainty in climate models estimates regarding precipitation and runoff changes while showing significant geographical variations. With respect to energy demand, climate change is expected to affect energy consumption, but the expected range of effects depends on both the implementation and the characteristics (deep vs. shallow renovation) of measures for upgrading the thermal performance of the building stock and the intensity of climate change.

The impact of climate change on water resources is a global issue with significant regional implications. The Ghba subbasin has experienced a higher socioeconomic change. In this paper, we assess the potential impact of climate change and human activity on water supply and demand in the Ghba subbasin of Ethiopia. We then evaluate the effectiveness of regional adaptation strategies for water supply management under these conditions. To do this, we use the statistical downscaling model (SDSM) and the water assessment and planning tool (WEAP) to simulate and analyse future water conditions. After running the model through a calibration and validation process, minimum (Tmin) and maximum (Tmax) temperatures, water demand and unmet water demand were projected for 2100 horizon, using different climate change scenarios. The results showed that the model's performance, calibration, and validation were all satisfactory. The analysis showed that, under A2 and B2 emission scenarios of the Intergovernmental Panel on Climate Change (IPCC), the mean precipitation will increase by 31% and 26%, respectively. The projected mean Tmax and Tmin will be warmer than the baseline period, with Tmax increasing by 1.5°C (A2) and 1.3°C (B2), and Tmin by 1.7°C (A2) and 1.5°C (B2) by 2100. The results also illustrate that in all scenarios, water consumption would rise and that this need will not be satisfied, and the pressure on water resources will intensify, resulting in a water shortage. The findings show that future water demand under the influence of climate change is projected to exceed 210 million cubic meters (MCM) by 2100. The findings show that while the evaluations of the recommended adaption techniques are effective, they are not enough to guarantee the Ghba subbasin's water sustainability.

Energy demand forecasting is a fundamental aspect of modern energy management. It impacts resource planning, economic stability, environmental sustainability, and energy security. This importance is making it critical for countries worldwide, particularly in cases like Türkiye, where the energy dependency ratio is notably high. The goal of this study is to propose ensemble machine learning methods such as boosting, bagging, blending, and stacking with hyperparameter tuning and k-fold cross-validation, and investigate the application of these methods for predicting Türkiye's energy demand. This study utilizes population, GDP per capita, imports and exports as input parameters based on historical data from 1979 to 2021 in Türkiye. Eleven combinations of all predictor variables were analyzed, and the best one was selected. It was observed that a very high correlation exists among population, GDP, imports, exports, and energy demand. In the first phase, the preliminary performance was investigated of 19 different machine learning algorithms using 5-fold cross-validation and measured their performance using five different metrics: MSE, RMSE, MAE, R-squared, and MAPE. Secondly, ensemble models were constructed by utilizing individual machine learning algorithms, and the performance of these ensemble models was compared with both each other and the best-performing individual machine learning algorithm. The analysis of the results revealed that placing Ridge as the meta-learner and using ET, RF and Ridge as the base learners in the stacking ensemble model produced superior results compared to the other models across performance metrics. It is anticipated that the findings of this research can be applied globally and prove valuable for energy policy planning in any country. The results obtained not only highlight the accuracy and effectiveness of our predictive model but also underscore the broader implications of this study within the framework of the United Nations' Sustainable Development Goals (SDGs).

We select four important waves of new entrants that knocked on the door of European electricity markets to illustrate how market rules need to be continuously adapted to allow new entrants to come in and push innovation forward. The new entrants that we selected are utilities venturing into neighbouring markets after establishing a strong position in their home market, utility-scale renewables project developers, asset-light software companies aggregating the assets of smaller consumers and producers, and different types of communities. We show that well-intentioned rules designed for certain types of market participants can (unintentionally) become obstacles for new entrants. We conclude that the evolution of market rules illustrates the importance of dynamic regulation. At the start of the liberalisation process the view was that we would deregulate or re-regulate the sector after which the role of regulators could be reduced. But their role has only increased. New players might also present new risks that require intervention by regulators.

The megacities´ sewage creates socioeconomic dependence related to water availability in the nearby zones, especially in countries with hydric stress. The present paper studies the water balance progression of realistic scenarios from 2005 to 2050 in the Mezquital Valley, the receptor of Mexico City untreated sewage since 1886, allowing agriculture irrigation in unsustainable conditions. WEAP model calculated the water demand and supply. Validation was performed with outflows data of the Tula River and simulated three scenarios: 1st) Steady-state based on inertial growth rates, 2nd) Transient scenario concerned climate change outcomes, with minor influence in surface water and hydric stress in 2050; 3rd) Transient scenario perturbed with a planned reduction of 36% in the imported wastewater and the start-up of a massive Water Treatment Plant, allowing drip and sprinkler irrigation since 2030. In the 2005-2017 period, 59% of the agriculture depended on the flood irrigation with megacity sewage. The water balance scenarios evaluated the sectorial supply of the ground and superficial water. Drip irrigation would reduce 42% of agriculture demands, but still does not grant the downflow hydroelectric requirements, aggravated by the lack of wastewater supply since 2030. This research alerts about how present policies compromise future Valley demands.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

Healthy diet interventions have been shown to improve depressive symptoms, but there is a need for randomized controlled trials (RCTs) that are double-blind and investigate biological mechanisms. The primary objectives of this randomized controlled pilot trial were to test the palatability of the meals and acceptability of the intervention in preparation for a future 8-week RCT which will investigate whether a healthy Nordic diet improves depressive symptoms in individuals with major depressive disorder, and associated biological mechanisms. Depressed (n=10) and non-depressed (n=6) women and men were randomized to receive either a healthy Nordic diet (ND) or a control diet (CD) for 8 days. Participants were blinded to diet allocation and study hypotheses. Health questionnaires were completed before and after the intervention, and, throughout the study, questionnaires assessed ratings of liking and sensory properties of the meals, adherence, and open-ended feedback. In the ND group, 75% of participants consumed no non-study foods, compared to 50% of CD participants. The meals of both diets, on average, received good ratings for liking and sensory properties, though the ND ratings were somewhat higher. Overall, results were positive and informative, indicating that the planned RCT will be feasible and well-accepted, with some proposed modifications.

A Demand-side management technique are deployed along with battery energy-storage systems (BESSs) to lower the electricity cost by mitigating the peak load of a building. Most of the existing methods rely on manual operation of the BESS, or even an elaborate building energy-management system resorting to a deterministic method that is susceptible to unforeseen growth in demand. In this study we propose a real-time optimal operating strategy for BESS based on density demand forecast and stochastic optimization. This method takes into consideration uncertainties in demand when accounting for an optimal BESS schedule, making it robust compared to the deterministic case. The proposed method is verified and tested against existing algorithms. Data obtained from a real site in South Korea is used for verification and testing. The results show that the proposed method is effective, even for the cases where the forecasted demand deviates from the observed demand

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

Despite a significant number of investigations in the field of phosphazene chemistry, the mechanism of this class cyclic compounds formation is still poorly studied. At the same time, a thorough understanding of this process is necessary both for the direct production of phosphazene rings with a given size, and for the controlled cyclization reaction when it is secondary and undesirable. Here we have synthesized a series of short linear phosphazene oligomers with the general formula Cl[PCl2=N]n–PCl3+PCl6– and studied their tendency to form cyclic structures under the influence of elevated temperature or in the presence of nitrogen-containing agents, such as hexamethyldisilazane (HMDS) or ammonium chloride. It was established that linear oligophosphazenes are inert when heated in the absence of the mentioned cyclization agents, and the formation of cyclic products occurs only when these agents are involved in the process. It is for the first time shown the ability to obtain the desired size phosphazene cycle from corresponding linear chain. Known obstacles like side interaction with the PCl6– counterion and a tendency of longer chains to undergo crosslinking elongation instead of cyclization are still relevant and ways to overcome them are being discussed.

In the present study the synthesis of gold nanoparticles (AuNPs) loaded with methotrexate (MTX) has been carried out in order to obtain controlled size and monodispersed nanocarriers, around 20nm. Characterization study shows metallic AuNPs with MTX polydispersed on the surface. MTX is linked by a replacement of citrate by the MTX carboxyl group. The drug release profiles showed faster MTX release when it is conjugated, which leads to the best control of plasma concentration. Also, the enhanced release observed at pH 5 could take advantage of the pH gradients that exist in tumor microenvironments to achieve high local drug concentrations. AuNPs-MTX conjugates were tested by flow cytometry against lung (A-549) and colon (HTC-116) cancer cell lines. Results for A-549 showed a lighter dose-response effect than for colon cancer ones. This could be related to the presence of folate receptors in line HTC-116 on the contrary than line A-549, supporting the specific uptake of folate-conjugated AuNPs-MTX by folate receptor positive tumor cells. Conjugates exhibited considerably higher cytotoxic effects compared with the effects of equal doses of free MTX. Anexin V-PI test sustain as cell death mechanism apoptosis, which is normally disabled in cancer cells.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

The present study explored the effects of a Second-generation mindfulness-based intervention known as Flow Meditation (Meditación-Fluir) in the improvement of life habits. A sample of university students (n = 51) in Spain were randomly assigned to a seven-week mindfulness treatment or a waiting list control group. Results showed that compared to the control group, individuals in the mindfulness group demonstrated significant improvements across all outcome measures, including healthy eating habits (balanced diet, intake rate, snacking between meals, decrease in consumption by emotional states negative, increased consumption by negative emotional states, amount of consumption, meal times, consumption of low-fat products), tobacco, alcohol and cannabis consumption, and resting habits. There were differences between males and females in some of these variables and a better effect of the treatment was evident in the females of the experimental group as compared to males. The Flow Meditation program shows promise for fostering healthy life habits, thus decreasing behaviors related to maladaptive eating, tobacco, alcohol and drug consumption, as well as negative resting habits, in university students. This mindfulness program can significantly contribute in the treatment of eating disorders and addictions, wherein negative emotional states and impulsivity are central features of the condition.

Background: Feasibility trials are preliminary trials that assess the viability and acceptability of intervention studies and the effects of the intervention on intermediate endpoints. Due to their short duration, they are unable to establish the effects of the intervention on long-term clinical outcomes. We propose a novel method that could transform the interpretation of feasibility trials using modified two-stage randomisation analyses. Methods In this two-stage process, we explored the effects of a 6-month feasibility factorial randomised controlled trial (RCT) of lycopene and green tea dietary interventions (ProDiet) on 159 serum metabolic traits in 133 men with raised PSA levels but prostate cancer (PCA) free. In the first stage, we conducted an intention-to-treat analysis, using linear regression to examine the effects of the interventions on metabolic traits, compared to the placebo group and instrumental variable analysis to assess the causal effect of the intervention on the outcomes. In the second stage, we used a two-sample Mendelian Randomization (MR) approach to assess the causal effect of metabolic traits altered by the interventions, on PCA risk, using summary statistics data from an international PCA consortium of 44,825 cancer cases and 27,904 controls. ResultsThe systemic effects of lycopene and green tea supplementation on serum metabolic profile were comparable to the effects of the respective dietary advice interventions (R2= 0.65 and 0.76 for lycopene and green tea respectively). Metabolites which were altered in response to lycopene supplementation were acetate (standard deviation difference versus placebo (β)): 0.69; 95% CI= 0.24, 1.15; p=0.003), valine (β: -0.62; -1.03, -0.02; p=0.004), pyruvate (β: -0.56; -0.95, -0.16; p=0.006), and docosahexaenoic acid (β: -0.50; -085, -0.14; p=0.006). The instrumental variable analysis showed there was no evidence that green tea altered the metabolome, but lycopene was associated with an increase in acetate (β=2.13; p=0.006) and decreases in pyruvate (β=-1.90; p=0.009), valine (β=-1.79; p=0.023), diacylglycerol (β=-1.81; p=0.026), alanine (β=-1.55; p=0.015) and DHA (p=0.097), where the regression coefficient represents the standard deviation (SD) difference in metabolite measures per unit change in lycopene (µmol/L) or EGCG (nM).Using MR, a genetically instrumented SD increase in pyruvate increased the odds of PCA by 1.29 (1.03, 1.62; p=0.027). Conclusion Using a two-stage randomization analysis in a feasibility RCT, we found that lycopene lowered levels of pyruvate, which our Mendelian randomization analysis suggests may be causally related to reduced PCA risk.

The aim of this work is to analyze and investigate the shape preserving properties of ternary 4-point non-stationary interpolating subdivision schemes constructed by Beccari et al. [1] with a tension parameter !k+1 which can reproducing exponential. Moreover, the conditions on the initial control points are developed that allow user to generate shape preserving limit curves after a nite number of subdivision steps and generalize these results in limiting case. Signicance of derived conditions are illustrated through graphs and the whole discussion is followed by examples.

Halloysite nanotubes (HNTs) are natural occurring mineral clay nanotubes that have excellent application potential in different fields. However, HNTs are heterogeneous in size, surface charge and formation of surfacial hydrogen bond, which lead to weak affinity and aggregation at a certain extent. It is very important to modify the HNTs’ surface to expand its applications. In this review, the structural characteristics, performance and the related applications of surface-modified HNTs are reviewed. We focus on the surface-modified variation of HNTs, the effects of surface modification on the materials and related applications in various regions. In addition, future prospects and the meaning of surface modification were also discussed in HNTs studies. This review provides a reference for the application of HNTs modifications in the field of new nanomaterials.

Hydrogels evolved as an outstanding carrier material for local and controlled drug delivery that tend to the shortcomings of old conventional dosage forms for small drugs (NSAIDS) and large peptides and proteins. Aqueous swellable and crosslinked polymeric network structure of hydrogels is composed of various natural, synthetic and semisynthetic biodegradable polymers. Hydrogels have remarkable properties of functionality, reversibility, sterilizability, and biocompatibility. All these dynamic properties of hydrogels have increased the interest in their use as a carrier for peptides and proteins to be released slowly in a sustained manner. The therapeutical peptide and proteins are remarkable therapeutic agents in today’s world that allows the treatment of severe, chronic and life‐threatening diseases, such as diabetes, rheumatoid arthritis, hepatitis in an easy manner. Despite few limitations, hydrogels provide fine tuning of proteins and peptides delivery with enormous impact in clinical medicine. The primary objective of this article is to review current issues concerned with the therapeutics peptides and proteins and impact of remarkable properties of hydrogels on these therapeutic agents. Different routes for pharmaceutical peptides and proteins and superiority over other drugs candidates are presented. The article will also review literature concerning classification of hydrogels on different basis, polymers used, release mechanisms their physical and chemical characteristics and diverse applications.

A new approach for the preparation of polymer brush was developed via the union of controlled/“living” radical polymerization and click chemistry. The application of the approach realized the more quickly and accurate design and synthesis of the polymer brushes. A novel functional polymer brush of poly(acrylonitrile-g-glycidyl methacrylate) with tremendous application potential in the field of biology has been successfully synthesized via the new approach. The reaction conditions of click chemistry were optimized with the reaction time and the reactant ratio and judged from UV-vis spectra. Under the optimum of click chemistry, the novel functional polymer brushes were prepared. The GPC, FTIR analyses, 1H NMR spectrum and TGA were employed to ensure the successful synthesis of poly(acrylonitrile-g-glycidyl methacrylate) polymer brushes.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

When following a prescribed route, we need to decide at each intersection which way to proceed. The present work addressed several factors that might influence the difficulty of this decision making process. Participants repeatedly followed a route through a virtual maze with twelve or eighteen intersections, and with two or three choices per intersection. One group performed task S, which promoted decision making by the serial order strategy since all intersections looked alike. Another group performed task SA, which allowed the use of the serial order and the associative cue strategy since unique visual cues were presented at each intersection. We found that in both tasks, participants were more accurate in making decisions on routes with twelve rather than eighteen intersections, and more accurate by a similar amount on routes with two rather than three choices. Reaction time in task SA was reciprocal to accuracy; reaction time in task S was generally lower and route-independent. Accuracy in task SA was similar for participants who experienced smooth transport across intersections and those who experienced abrupt transport, while accuracy in task S was lower for participants who experienced smooth rather than abrupt transport across intersections. We conclude that the number of intersections and the number of choices were equivalent determinants of route following difficulty. We further conclude that optic flow during turns at intersections interfered with anticipatory decision making in task S; hence natural (smooth) transport across intersections did not enhance route following performance.

The literature, aimed at understanding the income-price elasticity of air passenger demand, bases its analysis on airport movement. The diversity of studies regarding the casualty between air transportation and economic growth are examples. Some studies covering this link, estimate the income-price relationship with the demand considering international traffic. Considering a domestic setting, where this traffic is significant in Brazil, studies related to remote regions are scarce, and the existing ones focus on governmental policies and subsidies. In addition, empirical studies on the theme consenter themselves in developed regions, such as Europe, North America, and Australia. For Brazil, where we find the Amazon region, there are no empirical researches. This paper analyses the price-income elasticity of the demand regarding domestic passengers in air links from remote cities of the Brazilian Amazon. This study uses panel data regression analysis method on a database of domestic scheduled flights of Brazil´s National Civil Aviation Agency. The results show that air passengers involving remote region flights present a lower sensitiveness regarding local income and airline´s price variations than those in flights among capitals. The higher difference is in income-elasticity of the remote city of origin, which is lower than that of the air traffic among capitals.

Background and Objectives: Due to huge demand and availability of Banana, innovative cost effective method is necessary to promote and smoothen the banana production among farmers commercially mitigating the demand. Method and Materials: In this study, we feed cow dung mixture along with Urea, TSP, MoP, water to the distal part of rachis after cutting down male bud as soon as the female flowers matured into fruits (T1). The effect of this method was then compared with two control groups; one with the same strategy except fertilizer applied on root following ring method (C1, Positive control) and another was male flower untouched without applying fertilizer on rachis or root (C2, Negative control). Results and Conclusion: T1 showed more than double increase in length than controls. In the same way, in case of shape (diameter), T1 (0.46 cm) showed twice as better growth in the C1 (0.22 cm) and C2 (0.18 cm). Trend analysis showed the test group T1 curve is much steeper than the control groups suggesting faster growth rate than the other two. Finally, the cost of fertilizers for T1 per plant was estimated 0.091 USD while for positive control C1 it was 2.9 USD. This study shows an approach to be effective and economic comparing to traditional method of fertilizer application, which can be adapted as a new method of banana production.

As climate is not only a valuable tourism resource but also a factor influencing travel experience, estimating climate change can provide implications to sustainable development of the tourism industry. This study develops Climate Volatility Index (CVI) using GARCH model and estimates the relationship between CVI and Japanese tourism demand for Korea using a tourism demand model, based on data from January 2000 to December 2013. Time lag is applied based on a decision making process regarding travel destinations. The result shows that an increase in volatility of climate change leads to a decrease in tourism demand.

In the present study, a hybrid optimizing algorithm has been proposed using Genetic Algorithm (GA)and Particle Swarm Optimization (PSO) for Artificial Neural Network (ANN) to improve the estimation of electricity demand of the state of Tamil Nadu in India. The GA-PSO model optimizes the coefficients of factors of gross state domestic product (GSDP) , electricity consumption per capita, income growth rate and consumer price index (CPI) that affect the electricity demand. Based on historical data of 25 years from 1991 till 2015 , the simulation results of GA-PSO models are having greater accuracy and reliability than single optimization methods based on either PSO or GA. The forecasting results of ANN-GA-PSO are better than models based on single optimization such as ANN-BP, ANN-GA, ANN-PSO models. Further the paper also forecasts the electricity demand of Tamil Nadu based on two scenarios. First scenario is the "as-it-is" scenario , the second scenario is based on milestones set for achieving goals of "Vision 2023" document for the state. The present research also explores the causality between the economic growth and electricity demand in case of Tamil Nadu. The research indicates that a direct causality exists between GSDP and the electricity demand of the state.

In the present study, a hybrid optimizing algorithm has been proposed using Genetic Algorithm (GA)and Particle Swarm Optimization (PSO) for Artificial Neural Network (ANN) to improve the estimation of electricity demand of the state of Tamil Nadu in India. The GA-PSO model optimizes the coefficients of factors of gross state domestic product (GSDP) , electricity consumption per capita, income growth rate and consumer price index (CPI) that affect the electricity demand. Based on historical data of 25 years from 1991 till 2015, the simulation results of GA-PSO models are having greater accuracy and reliability than single optimization methods based on either PSO or GA. The forecasting results of ANN-GA-PSO are better than models based on single optimization such as ANN-BP, ANN-GA, ANN-PSO models. Further the paper also forecasts the electricity demand of Tamil Nadu based on two scenarios. First scenario is the “as-it-is” scenario, the second scenario is based on milestones set for achieving goals of “Vision 2023” document for the state. The present research also explores the causality between the economic growth and electricity demand in case of Tamil Nadu. The research indicates that a direct causality exists between GSDP and the electricity demand of the state.

This article describes an approach for optimising sensor-controlled systems through minimal intervention, utilising Fuzzy Linear Systems of Equations (FLSE). Staring with a generalised model of the system behaviour, incorporating an array of control units, environmental sensors, and an expert knowledge base. The described problems of detecting the level of intervention needed to change the system state to another is handled with the help of developed methods for solving the inverse problem for FLSE. By achieving minimal intervention, we ensure that system adjustments effective, economically optimal and non-intrusive. A MATLAB-based implementation is presented.

The agricultural sector faces challenges due to climate change and the growing global population. Alkaline stress could adversely impact plant growth and crop production. This stressor diminishes water quality essential for crop cultivation, consequently impairing plant growth and overall productivity. Gamma-aminobutyric acid (GABA), a non-protein amino acid, may exhibit multifaceted roles in plant responses to adverse environmental conditions. Optimization of crop production in controlled environmental agriculture under artificial light attracted much attention. In the present study, we investigated the effects of different light spectra and GABA concentrations on Lollo Rosso lettuce plants under alkaline stress. Seedlings were placed under different light spectra [red (R), blue (B), white (W), 3R:1B, and 2R:1B:1far-red (FR)] and treated by GABA (0 and 50 µmol). Alkaline conditions were instituted by applying NaHCO3 at a concentration of 40 mM. The experiment incorporated a control treatment without NaHCO3. In general, R light exposure caused the highest growth performance of lettuce plants. GABA augmented biomass production in control and alkaline-treated plants across all light spectra. Additionally, it increased the concentrations of photosynthetic and protective pigments under alkaline conditions. GABA also improved the photosynthetic performance under all light spectra. Non-photochemical quenching and pigmentation were enhanced by exposure to B light, especially in plants treated with GABA. Alkaline stress induced an increase in soluble carbohydrate content in the lettuce leaves. These findings highlight the support of GABA application in facilitating coping plants to alkaline stress.

The design of randomized controlled trials for low-resource settings has unique challenges. One challenge is ensuring recruitment success in the face of a lack of information about prevalence of disease in the population. What disease burden data may exist is old and from distant regions, adding guesswork into site design. This leads to a high chance that the sample size will not be recruited in any reasonable timeframe—a challenge even in high-resource settings. While cross-sectional prevalence studies could be used as a type of feasibility study informing trials by generating near real-time prevalence estimates for the future trial site, such studies take years to complete. This duration makes insertion of such a study in trial design impossible. An empirically supported combination of new approaches that sidesteps unnecessary hurdles is presented, the Pop-Up Prevalence with Private Ethics (PUPPE) design. PUPPE includes using a COVID-validated, more targeted method of data collection, use of accepted ethics review from universities or hospitals to avoid lengthy public ethics review, and—if needed—post-study in silico participant randomization. Only this design would enable clinical trial designers to insert fit-for-purpose prevalence studies within the design phase of their trials, leading to informative outcomes.

Basil (Ocimum basilicum L.) is one of the important medicinal and aromatic plants. Light intensity is an indispensable factor for plants due to its effect on photosynthesis and physiological processes. Here, we investigated the impact of light intensities and harvesting times on the photosynthesis of green and purple basil. The experiment involved subjecting the plants to three different sunlight levels for 12 days: complete – 100%, 50%, and 30% sunlight. In addition, we scrutinize the harvesting time. The highest levels of photosynthetic and protective pigments were detected under full sunlight conditions in the purple basil harvested at noon. The highest levels of soluble and storage carbohydrates were recorded in the purple basil grown under full sunlight and harvested in the early morning. In contrast, their lowest levels were obtained in plants grown under 30% sunlight and harvested at noon time. Under all light treatments, the maximum quantum yield of photosystem II (FV/FM) was detected at 4 a.m. in both basil varieties; it decreased at noon and increased again at 5 p.m. Non-Photochemical Quenching (NPQ) got most elevated in the green variety under all light intensities at noon. However the highest NPQ was detected in the purple variety at 8 a.m. The NPQ was lowest in both basil varieties during the early morning and afternoon. Full sunlight at noon caused temporary photoinhibition and reduced car-bohydrates while enhancing pigment concentration and photo-protective mechanisms in basil plants.

The efficacy of time-restricted feeding for weight loss has not been established as prior studies were limited by lack of controlled isocaloric designs. This study describes the design and implementation of a controlled feeding study evaluating time-restricted feeding. We designed a randomized, controlled, parallel-arm, feeding study comparing time restricted feeding (TRF) to a usual feeding pattern (UFP) for the primary outcome of weight change. Participants were aged 18-69 years with prediabetes and obesity. TRF consumed 80% of calories by 1300, and UFP consumed ≥50% of calories after 1700. Both arms consumed identical macro- and micro-nutrients, based on a healthy palatable diet. We calculated individual calorie requirements which were maintained throughout the intervention. We randomized 41 participants who all completed the study. The desired distribution of calories across feeding windows in both arms was achieved, as were weekly averages for macronutrients and micronutrients. All randomized participants completed the study. We actively monitored participants and adapted diets to facilitate adherence. We provide the first report, to our knowledge, on the design and implementation of a feeding study that isolated the effect of meal timing on weight, while maintaining constant caloric intake and identical diets during the study period.

Objectives: To determine the prevalence of controlled systemic hypertension and its associated risk factors among the hypertensive patients who attended the clinic at Mbeya Zonal Referral Hospital in Tanzania. Methods: A descriptive cross-sectional quantitative study was used determine the prevalence of co to 252 hypertensive patients were recruited during clinic visit from September to November 2020 and participant was randomly selected interviews using structured self-administered questionnaires. Data was analyzed using chi square test to find the risk factors associated with controlled hypertension. Results: Among 252 participants, 94(39.7%) individuals with controlled hypertension giving the prevalence of controlled hypertension. The proportion of females with controlled hypertension was slightly higher than male (49 females to 45 males). The prevalence of uncontrolled hypertension was 152(60.3%) participants. The prevalence of controlled hypertension was higher among patients who have regular clinic visit (p< .05) and have daily adherence to their anti-hypertensive medication. A similar trend was observed among participants without financial challenges to attend clinic, short duration of illness, higher level of education and there was no association between age, sex, marital status, smoking, alcohol consumption, having health insurance and having chronic illness. Conclusion: Prevalence of controlled hypertension is higher among patients who have regular clinic visit and have daily adherence to their anti-hypertensive medication. Also, it is higher among participants without financial challenges to attend clinic so they can have regular clinic visit and checkup. Reinforcement on regular drug intake and clinic visit, good nutrition and reduced salt intake and modifying lifestyles of patient with hypertension is important.

Doxorubicin, a member of the anthracycline family, is a common anticancer agent often used as a first line treatment for the wide spectrum of cancers. Doxorubicin-based chemotherapy, although effective, is associated with serious side effects, such as irreversible cardiotoxicity or nephrotoxicity. Those often life-threatening adverse risks, responsible for the elongation of the patients' recuperation period and increasing medical expenses, have prompted the need for creating novel and safer drug delivery systems. Among many proposed concepts, polymeric nanocarriers are shown to be a promising approach, allowing for controlled and selective drug delivery simultaneously enhancing its activity towards cancerous cells and reducing toxic effects on healthy tissues. This article is a chronological examination of the history of the work progress on polymeric nanostructures, designed as efficient doxorubicin nanocarriers, with the emphasis on the main achievements of 2010-2020. Numerous publications have been reviewed to provide an essential summation of the nanopolymer types and their essential properties, mechanisms towards efficient drug delivery, as well as active targeting stimuli-responsive strategies that are currently utilized in the doxorubicin transportation field.

Polyhydroxyalkanoate (PHA) co-polymers show relatively higher in vivo degradation rate compared to other PHAs thus they received a great deal of attention for a wide range of medical applications. Nanoparticles (NPs) loaded with poorly water soluble anticancer drug docetaxel (DCX) were produced using poly 3-hydroxybutyrate-co-4-hydroxybutyrate, P(3HB-co-4HB), co-polymers biosynthesised from Cupriavidus sp. USMAA1020 isolated from Malaysian environment. Three co-polymers with different molar proportions of 4-hydroxybutirate (4HB) were used: 16% (PHB16), 30% (PHB30) and 70% (PHB70) 4HB-containing P(3HB-co-4HB). Blank and DCX loaded nanoparticles were then characterized for their size and size distribution, surface charge, encapsulation efficiency and drug release. Pre-formulation studies showed that an optimised formulation could be achieved through the emulsification/solvent evaporation method using PHB70 with the addition of 1.0% PVA, as stabilizer and 0.03% VitE-TPGS, as surfactant. DCX-loaded PHB70 nanoparticles (DCX-PHB70) gave the desired particle size distribution in term of average particles sizes around 150 nm and narrow particle size distribution (PDI below 0.100). The encapsulation efficiencies result showed that at 30% w/w drug-to-polymer ratio: DCX- PHB16 NPs were able to encapsulate up to 42% of DCX; DCX-PHB30 NPs encapsulated up to 46% of DCX and DCX-PHB70 NPs encapsulated up to 50% of DCX within the nanoparticles system. Approximately 60% of DCX was released from the DCX-PHB70 NPs within 7 days for 5%, 10% and 20% of drug to polymer ratio while for the 30% and 40% drug to polymer ratios, an almost complete drug release (98%) after 7 days of incubation was observed.

In recent years, polyureas with dynamic hindered urea bonds (HUBs), as a class of promising biomedical polymers, have attracted attention as a benefit of their controlled hydrolytic property. The effect of the chemical structures on the properties of polyureas and their assemblies was rarely reported. In this study, four kinds of polyureas with different chemical groups have been synthesized, and the polyurea from cyclohexyl diisocyanate and tert-butyl diamine showed the fastest hydrolytic rate. The amphiphilic polyurea composed of hydrophobic cyclohexyl-tert-butyl polyurea and hydrophilic poly(ethylene glycol) was synthesized for controlled delivery of antitumor drug paclitaxel (PTX). The PTX-loaded PEGylated polyurea micelle more effectively entered into the murine breast cancer 4T1 cells and inhibited the corresponding tumor growth in vitro and in vivo. Therefore, the PEGylated polyurea with adjustable degradation might be a promising polymer matrix for drug delivery.

One-dimensional nanostructures such as silver nanowires (AgNWs) have attracted considerable attention owing to their outstanding electrical, thermal and antimicrobial properties; however, their application in the prevention of infections linked to bone tissue regeneration interventions has not yet been explored. Here we report on the development of an innovative scaffold prepared from chitosan, composite hydroxyapatite and AgNWs (CS-HACS-AgNWs) having both bioactive and antibacterial properties. In vitro results highlighted the antibacterial potential of AgNWs against both gram-positive and gram-negative bacteria. The CS-HACS-AgNWs composite scaffold demonstrated suitable Ca/P deposition, improved gel strength, reduced gelation time, and sustained Ag+ release within therapeutic concentrations. Antibacterial studies showed that the composite formulation was capable of inhibiting bacterial growth in suspension and of completely preventing biofilm formation on the scaffold in the presence of resistant strains. The hydrogels were also shown to be biocompatible, allowing cell proliferation. In summary, the developed CS-HACS-AgNWs composite hydrogels demonstrated significant potential as a scaffold material to be employed in bone regenerative medicine, as it presents enhanced mechanical strength combined with the ability to allow calcium salts deposition, while efficiently decreasing the risk of infections. The results presented justify further investigations into potential clinical applications of these materials.

Since autism was first recognised, prevalence has increased rapidly. The growing economic as well as social cost to society can only be mitigated by effective interventions and supports. It is therefore not surprising that most governments have developed public policy documents to address the management of autism. Over the past 40-50 years, meaningful evidence has accrued showing that interventions based on the scientific discipline of Applied Behaviour Analysis (ABA) can help people with autism reach their potential. In view of this, nearly all of North America has laws to mandate that ABA-based interventions are available through the health care systems. In contrast, across Europe there are no such laws. In fact, the National Institute for Health and Care Excellence (NICE), the body guiding health and social policy in the UK, concluded that it could not find any evidence to support ABA, and therefore could not recommend it. This paper addresses the reasons for these diametrically opposed perspectives. In particular, it examines what happens when health and social care policy is misinformed about effective autism intervention.

Gait variability (GV) is a crucial measure of inconsistency of muscular activities or body seg-mental movements during repeated tasks. Hence, GV might serve as a relevant and sensitive measure to quantify adjustments of walking control. However, has not been clarified whether GV is associated with walking speed to exploit effective better coordination level. Fourteen male stu-dents (age 22.4 ± 2.7 years, body mass 74.9 ± 6.8 kg, body height 1.78 ± 0.05 m) took part in this study. After three days of walking 1 km each day at a self-selected speed (SS) on asphalt with Apple Watch S. 7 (AppleTM), the participants were randomly evaluated on a treadmill at three different walking speed intensities for 10 minutes each one, at SS-20% / SS+20% of SS, with 5 minutes of passive recovery in-between. Heart rate (HR) was monitored beat-to beat and nor-malized as HR%MAX, while the rate of perceived exertion (RPE) (CR-10) was asked after each trial. Kinematic analysis was performed assessing the Contact Time (CT), Swing Time (ST), Stride Length (SL), Stride Cycle (SC) and Gait Variability as Phase Coordination Index (PCI). RPE and HR increased with higher walking speed (P = 0.005 and P = 0.035, respectively). CT and SC decreased as the speed increased (P = 0.0001 and P = 0.013, respectively), while ST remained un-changed (P = 0.277). SL increased with higher walking speed (P = 0.0001). Conversely, PCI was 3.81 ± 0.88 % (high variability) at 3.96 ± 0.47 km·h-1, 2.64 ± 0.75 % (low variability) at SS (4.94 ± 0.58 km·h-1), 3.36 ± 1.09 % (high variability) at 5.94 ± 0.70 km·h-1 (P = 0.001). These results indi-cate that while the metabolic demand and kinematics variables changing linearly with increasing speed, the most effective GV was observed at SS. Therefore, SS could be a new methodological approach to choose the individual walking speed, normalize the speed intensity, and avoid a gait pattern alteration.

Metal Additive Manufacturing (MAM) has emerged as a promising technology in the aerospace industry, enabling the production of complex components with enhanced design flexibility and reduced lead times. Concurrently, Industry 4.0 has gained significant attention for its potential to revolutionize aerospace manufacturing processes. The paper aims to cluster and review the literature on MAM in the aerospace industry, specifically focusing on its relevance to Industry 4.0 and its applicability throughout the various stages of the product life cycle for the chief purpose of matching supply with demand. Identified gaps and challenges are analyzed, highlighting the need for further research and outlining research agenda aimed at advancing the integration of MAM for Industry 4.0 in the aerospace sector. By addressing these research areas, the aerospace industry can unlock the value of MAM within an Industry 4.0 framework, leading to improved efficiency, productivity, and competitiveness.

Biochemical oxygen demand (BOD) is one of the most important factors to consider when evaluating water contamination. BOD5 is the amount of oxygen consumed in five days by microorganisms that oxidize biodegradable organic materials in an aerobic biochemical manner. The primary objective of this effort is to use microbial fuel cells (MFCs) to shorten the time required for BOD5 measurements. We created a regression artificial neural network (AI), and the predictions we obtained for BOD5 measurements were taken over 6 – 24 hours with an average error of just 7%. The outcomes demonstrated by our AI MFC/BES BOD5 sensor’s viability for use in real-world scenarios.

Globally, inequalities in educational provision are prevalent between genders, various geographical regions, and among different socio-economic backgrounds. Consequently, this study set-out to assess the level of disparity among the Federal Regional States of Ethiopia using Gini-coefficient and Lorenz curve from the statistical data of MoE. Moreover, data were collected from 656 respondents found in the sample regions. The result of the Gini-coefficient indicated that disparity in educational provision has been reduced over the past couple of decades both at primary (0.145 to 0.032) and secondary levels (0.277 to 0.126). Emerging regions are by far lagging behind the central and established regions. The sources of variation were mainly the demand-side variables, especially the economic and contextual related issues like drought and conflicts. Therefore, educational policies designed at the central level are advised to consider the strategies to bridge the existing inequalities through equitable provision of the education system to its citizen.

With the year 2020, the world faced a new threat that affects all areas of life, negatively affects production in all areas, and paralyzes social life. The measures and restrictions taken by the country's governments to prevent the epidemic from spreading rapidly in the society with the effect of the Covid-19 virus, which first appeared in China and spread all over the world, brought a new lifestyle. Covid-19 has been much the impact on electricity use and electricity production in the period in Turkey as in other countries. There was a sharp decline in commercial and industrial electricity use. The coronavirus effect has also been reflected in the electricity demand and the consumption amount has undergone a great negative change. Due to the enactment of measures against the new type of coronavirus (COVID-19) epidemic and the partial or full-time curfews, electricity consumption was moved to homes, supermarkets, and hospitals in April 2020 from places where mass consumption is intense, such as industry, workplaces, and educational institutions. In this study, Covid-19 period, the first cases were examined electricity production and consumption in Turkey as of the date it is seen throughout, in comparison with electricity consumption data in the same month of the previous years corresponding to this period, the effects on electricity generation and consumption habits of this period were examined.

In this paper, we consider a make-to-order supply chain which satisfies demand that is dependent on both price and quoted lead -time. The manufacturer chooses the lead -time and the order quantity, and the retailer sets the revenue shares. The interactions between the manufacturer and the retailer are modelled as a Nash Game, and the existence and uniqueness of pure strategy equilibrium are demonstrated. A mechanism that enables the supply chain to coordinate the decisions of the members is developed. Lastly, we also analyze how the supply chain system parameters impact the optimal supply chain decisions and the supply chain performance.

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

Power Electronic development determines introduction of nonlinear devices in Electric Power Systems. Introduction of nonlinear devices increase current harmonics in Transmission and Distribution Power Systems. Distribution transformers and feeders increase power losses and their nominal parameters are reduced. Present work introduces a procedure to evaluate maximum permissible load in single phase distribution transformers with massive introduction of a new type of nonlinear load which changes daily demand graphs.

Sustainability of current energy policies and known mid-term policies are analised in their multiple facets. First an overview is given about the trend of global energy demand and energy production, analysing the share of energy sources and the geographic distribution of demand, on the basis of statistics and projections published by major agencies. The issue of sustainability of the energy cycle is finally addressed, with specific reference to systems with high share of renewable energy and storage capability, highlighting some promising energy sources and storage approaches.

This paper examines an important problem in smart grid energy scheduling; peaks in power demand are proportionally more expensive to generate and provision for. The issue is exacerbated in local microgrids that do not benefit from the aggregate smoothing experienced by large grids. Demand-side scheduling can reduce these peaks by taking advantage of the fact that there is often flexibility in job start times. We focus attention on the case where the jobs are non-preemptible, meaning once started, they run to completion. The associated optimization problem is called the Peak Demand Minimization problem and has been previously shown to be NP-hard. Our results include an optimal fixed-parameter tractable algorithm, a polynomial-time approximation algorithm, as well as an effective heuristic that can also be used in an online setting of the problem. Simulation results show these methods can reduce peak demand by up to 50% versus on-demand scheduling for household power jobs.

The Smart Park (well-known as Taman Pintar) as a major educational tourism destination in Jogjakarta offers a variety of tourism attractions that are very interesting for tourists. The main purpose of tourists visiting Smart Park is to get an educational tourism experience. A subjective experience raises a specific challenge for Smart Park toward the status of competitive destination. The purpose of this study is to analyze the aspects of educational tourism experience that are affected by tourism demand and supply. Data were collected by survey technique to 150 respondents and analyzed using path analysis. The results of analysis show that tourism demand and supply contributed to the variation of tourism activities by 45.1%, while the remaining was explained by other variables, such as National Budget, Local Budget, ticket sale, and cooperation with some stakeholders. Tourism supply had a higher effect than tourism demand. Tourism demand did not partially affect tourism experience. However, the results of the path analysis indicate that tourism supply had direct and indirect effects on tourism experience through the variation of tourism activities with indirect effect being dominant. In the management of Smart Park, there is still a gap between tourism demand and supply, so that the environment of tourism experience has not been created maximally.

Copper demand for a country's copper industry has a greater pull effect. China's copper consumption in 2015 has accounted for 50% of the world. The scientific forecast of China's copper demands trend is also an important basis for analyzing its future environmental impact. This paper assumes that China's economy will be developing high, medium and low scenarios, and forecasts economic and social indicators such as total GDP, population and per capita GDP in China from 2016 to 2030. Then, predicted the demand of copper resources in China from 2016 to 2030 by the combination of system dynamics model, vector autoregressive moving average model and inverted U-type empirical model. The results show that: (1) in 2020, 2025 and 2030, China's refined copper demand will be 13 Mt, 15 Mt and 15.5 Mt. (2) China's copper demand growth slowed down significantly from 2016-2030. (3) 2025-2030, China's copper resource demand is stable, into the platform of demand growth, the highest peak value in 2027 will be 15.5 Mt. (4) 2030 years later, China's copper resource demand will enter a slow decline.

This research presents a novel approach for estimating soil organic carbon (SOC) content in agricultural soils using a photocatalytic Chemical Oxygen Demand (PeCOD) analyzer integrated with Geographic Information System (GIS) technology for spatial analysis. The PeCOD method, which relies on photochemical oxidation of organic carbon, demonstrated an uncanny correlation between its values and SOC content, making it a quick and accurate way to estimate SOC levels. Finer materials, such as clayey soils, demonstrated higher SOC content compared to coarser ones and decreased with increasing soil depth. GIS georeferencing enabled precise mapping of SOC distribution and identification of hotspot areas with high SOC content. This study highlights the significance of soil texture and depth on SOC distribution and emphasizes its significance within geological context when studying soil properties. Research results have practical ramifications for sustainable agriculture, climate change mitigation and soil health management - providing farmers and land managers with strategies that increase carbon sequestration while simultaneously improving soil health. Integrating PeCOD analyzer technology with GIS technology offers promising avenues for advanced soil carbon monitoring practices that promote climate-smart agricultural practices.

Transdermal drug delivery systems have become an intriguing research topic in healthcare technology and one of the most frequently developed pharmaceutical products in the global market. In recent years, researchers and pharmaceutical companies have made significant progress in developing new solutions in the field. This study sheds light on current trends, collaboration patterns, research hotspots, and emerging frontiers of transdermal drug delivery. Herein, a bib-liometric and patent analysis of data recovered from Scopus and The Lens databases, respectively, is reported over the last 20 years. From 2000 to 2022, the annual global publications increased from 131 in 2000 to 659 in 2022. Researchers in the United States, China, and India produced the highest number of publications. Likewise, most patent applications have been filed in the USA, China, and Europe. The recovered patents are 7,275, grouped into 2,997 patent families, of which 314 were granted. This study could support the work of decision-makers, scientific managers, or scientists to create new business opportunities or save money, time, and intellectual capital, thus, defining when a research or technology project should be a priority or not.

The cross-linked microspheres were prepared and loaded with Favipiravir SARS-CoV-2 antiviral drug, by copolymerization of chitosan (CS) with a polysaccharide extracted from fresh pomegranate peels. Moreover, glutaraldehyde (Glu) has been used as chemical cross-linker ,and sodium hexametaphosphate (SHMP) as physical cross-linker. The extracted polysaccharide was analyzed and different techniques have been used and the analyses leads to the fact that it is pectin .The surface morphology of the prepared microspheres was studied use scanning electron microscope where the size and the shape factor (S) of Glu microspheres have shown high values(74.27μm) and (0.852) respectively means their surfaces are tends to roughness, whereas the SHMP microspheres have shown size particle(20.47μm)and shape factor (0.748) which gives indication that the SHMP microspheres have smooth surfaces. The swelling studies have shown that Glu microspheres have higher degree of swelling which means SHMP microspheres are more compact. The prepared microspheres have shown more Loading percentage of Favipiravir antiviral drug in SHMP microspheres(37%w/w)in comparison with Glu microspheres(35%w/w) where the electrostatic interaction between the Favipiravir ions and SHMP anions help for more loading. The microspheres prepared under different types of cross-linking have shown initially burst release of Favipiravir and followed by a step of controlled release for a certain time where its period depends on the pH of the release media. Both Glu and SHMP cross-linked microspheres have shown high controlled release time in buffered release solution of pH 7.4 and for a less periods in pH 1.3 and pH 9.4 which may related to the type of electrostatic interactions between drug and polymer system and their reactions with release solution ions.

Main purposes and research question: Wheat is the second largest grain crop by tonnage in the world and the largest in Denmark. Given the observed, adverse impacts on wheat yields of climate change and the importance of wheat in the human diet, the purpose of this study was to use life cycle assessment to compare conventional wheat farming with indoor vertical farming using hydroponics. Methods: Life Cycle Assessment was used to assess the base case systems up to the “farm gate” for 1 tonne of wheat grain. The processes contributing most of the impacts were identified, and scenarios were assessed to determine how much the impacts could be reduced. Results: The conventional system outperformed the base case vertical system in every impact category, due to the electricity consumption in the lighting system. The scenarios included increasing the efficiency of the LED lighting and using 100% wind energy, but the conventional system still outperformed the vertical system by significant margins in all impact categories. This was due to the low photosynthetic conversion efficiency and the high energy density of wheat. Conclusions: Until significant improvements are made to lighting efficiency, the photosynthesis conversion efficiency of wheat, new wheat variants designed for vertical gardens and the sustainability of electricity supply, conventional wheat production will be environmentally preferable and vertical gardens would be advised to focus on food products with low energy densities.

The manipulation of participant allocation in randomized controlled trials to achieve equal groups sizes may introduce allocation bias potentially leading to larger treatment effect estimates. This study aimed to estimate the proportion of nursing trials that have precisely equal group sizes and examine if there was an association with trial outcome. Data were extracted from a sample of 148 randomized controlled trials published in nursing science journals in 2017. One hundred trials (68%) had precisely equal group sizes. Respectively, a positive outcome was reported in 70% and 58% of trials with equal/unequal groups. Trials from Asia were more likely to have equal group sizes than those from the rest of the world. Most trials reported a sample size calculation (n=105, 71%). In a third of trials (n=36, 34%), the number of participants recruited precisely matched the requirement of the sample size calculation; this was significantly more common in studies with equal group sizes. The high number of nursing trials with equal groups may suggest nurses con-ducting clinical trials are manipulating participant allocation to ensure equal group size increasing the risk of bias.

Vertical farming (VF) is a potential solution for the production of high-quality, accessible, and climate-friendly nutrition for growing urban populations. However, to realize VF’s potential as a sustainable food source, innovative technologies are required to ensure that VF can be industrialized on a massive scale and extended beyond leafy greens and fruits into the production of food staples or row crops. A major obstacle to the economic and environmental sustainability of VF is the lighting energy consumed. While technological advances have improved the energy efficiency of VF lighting systems, there has been insufficient research into biostimulation as an approach to reduce energy needs. We conducted a controlled trial to investigate the application of a phycocyanin-rich Spirulina extract (PRSE) as a biostimulant in hydroponically grown, vertically farmed lettuce (Lactuca sativa and Salanova®). PRSE application reduced the time from seeding to harvest by 6 days, increased yield by 12.5%, and improved quality including color, taste, texture, antioxidant flavonoid levels and shelf life. Metagenomic analysis of the microbial community of the nutrient solution indicated that PRSE increased the overall bacterial diversity including raising the abundance of Actinobacteria and Firmicutes and reducing the abundance of potentially pathogenic bacteria. This preliminary study demonstrates that microalgae-derived biostimulants may play an important role in improving the economic and environmental sustainability of VF.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

Transcriptionally controlled tumor protein (TCTP) is a highly conserved protein performing a large number of cellular functions by binding with various partner proteins. The importance of its roles in many diseases requires an assay method to find regulatory compounds. However, the molecular characteristics of TCTP made it difficult to search for chemicals interacting with it. In this study, a tryptophan-based assay method was designed and Y151W mutant TCTP was constructed to search binding chemicals. Since there is no tryptophan in the native sequence of TCTP, the incorporation of tryptophan in the Y151W mutant was very effective to establish the method. A flavonoid library was employed to the assay with the method. With the native and Y151W mutant TCTPs, three flavonoids such as morin, myricetin and isobavachalcone have been found to interact with TCTP. Combined with native gel electrophoresis, the binding region of isobavachalcone was suggested to be the flexible loop of TCTP. This approach can be easily applicable to find binding compounds of proteins with similar molecular characteristics of TCTP.

Modelling and presenting mathematical relationships for human behaviour is one of the most complex issues that researchers have always dealt with. In this article, a bottom-up framework for calculating agricultural needs is presented using the socioeconomic characteristics of farmers (such as education level, age, and dependence on income on agriculture) and how their lands are located concerning each other (interactions between neighbours). The objective function of this framework is to maximize the profit of individual farmers based on the amount of water received. Two scenarios, ABM1 (not considering neighbourhood effects) and ABM2 (all cases of farmers' placement and feeling neighbourhood effects), were investigated. In the first scenario (ABM1), there was a noteworthy reduction in water deficit volumes by approximately 35%, accompanied by a 20% increment in farmers' profits. Interestingly, higher risk-taking tendencies correlated with reduced profit margins. The second scenario (ABM2) underscored the significant role of neighborhood dynamics in cultivating diverse behavioral patterns among farmers, subsequently affecting their profitability. A granular examination revealed that farmers with a higher propensity for risk-taking generally accrued lower profits. Additionally, the study facilitated the calculation of total annual profits and average water consumption for each farmer, offering valuable insights for optimizing water resource management and allocation strategies. These findings are instrumental for planners and water resource managers aiming to promote sustainable agricultural practices and efficient water use.

In this paper, particular attention is paid to an advanced variant of the plug-in hybrid engine, known as PHEV, which combines two functionalities: the vehicle's internal combustion engine (ICEV) and the electric engine (BEV). The paper also presents the assumptions of the DEVS model, which allows for the estimation of vehicle’s energy consumption. The study described herein also presents the influence of factors such as ambient temperature and constant speed on the PHEV’s energy consumption. It has been shown that the vehicle’s range estimated based on its electronic control module (ECU) is about 20% shorter per annum on average for its year-round operation in every-day driving conditions. When analyzing the energy consumption based on the vehicle’s unit energy consumption model, attention was paid to values that are strongly correlated with the traffic volume and weather conditions affecting the moving vehicle. In addition, the authors emphasized that the estimated total energy consumption of an electric (BEV) or hybrid (PHEV) vehicle, relative to the normative values arising from the type approval test cycle, deviate from the actual values arising from real driving conditions and often vary substantially. In extreme cases, the actual range of a hybrid vehicle is 75% shorter.

Accurate demand forecasting plays a critical role in most furniture businesses’ operational, tactical, and strategic decisions, as the demand in the furniture business is considered seasonal and becomes more complex in crises. In this work, a neural network model using the Long Short-Term Memory (LSTM) method was developed to forecast the demand for specific product groups. LSTM is a leading deep learning model for time series prediction, particularly seasonal, multi-item, and non-linear situations. The developed model was used to predict the demand based on old data before the Covid-19 pandemic and recent data of the first months of the pandemic as a fast response to the crisis. In addition, a comparison study was conducted between the developed model and the traditional planning inventory used by furniture businesses that provided us with the data. The results showed that the Covid-19 pandemic significantly impacted demand forecasting. Also, the fast response to Covid-19 pandemic has slightly increased the model performance. Finally, the comparison study demonstrated that our model is robust and better than the traditional demand forecasting method. Therefore, the developed model may help the business improve inventory and production planning to create a more flexible supply chain.

Over the years, researchers have been studying the effect of weather and context data on the transport mode choice. The majority of these works are based on survey data, however the accuracy of their findings relies on how respondents give accurate and honest answers. In this paper, the potential of using GPS trajectories as an alternative to travel surveys in studying the impact of weather and context data on transport mode choices is investigated in Beijing city. In the analysis, we apply both descriptive and statistical models such as the MNL and MNP models. Our findings indicate that temperature has the most prominent effect among weather conditions. For instance, for temperatures greater than 25 °C, the walking share increases by 27% and the bike share reduces by 21%, which is line with the results from several survey studies. In addition, the evidence of government policy on transport regulation is revealed when the air quality becomes hazardous as people are encouraged to use environmentally friendly travel mode choices such as the bike instead of the bus and car, which are known CO2 emitters. Moreover, due to a series of traffic restrictions introduced by the Beijing government during the 2008 summer Olympics, a decrease of 17.5% in the car share and an increase of 13% and 10% in the walking and bus shares, respectively are observed. These findings provide a scientific basis for effective transport regulation and planning purposes.

The forecast of electricity demand has been a recurrent research topic for decades, due to its economical and strategic relevance. Several Machine Learning (ML) techniques have evolved in parallel with the complexity of the electric grid. This paper reviews a wide selection of approaches that have used Artificial Neural Networks (ANN) to forecast electricity demand, aiming to help newcomers and experienced researchers to appraise the common practices and to detect areas where there is room for improvement in the face of the current widespread deployment of smart meters and sensors, which yields an unprecedented amount of data to work with. The review looks at the specific problems tackled by each one of the selected papers, at the results attained by their algorithms, and at the strategies followed to validate and compare the results. This way, it is possible to highlight some peculiarities and algorithm configurations that seem to consistently outperform others in specific settings.

Although the dockless bike-sharing system, which can be regarded as a typical example of the resource-sharing system, has been increasingly popular for years with people especially in China, the imbalanced distribution of shared bikes gradually becomes a major problem for both bike-sharing companies and their customers. To solve the imbalance problem, we aim to investigate the long-term performance of a system under the influence of some key factors (with an emphasis on the unequal demand between different nodes), which can guide us to discover the causes of the problem and offer several valuable suggestions to the operators. According to the fundamental principle of a dockless bike-sharing system, we propose a model reduction method to reduce the complexity of the theoretical network models, which are developed based on the Markovian queueing theory with the consideration of higher-demand nodes and lower-demand nodes. The theoretical network models provide us with steady-state probabilities of having a certain number of bikes at one node, which are used as an important part of the optimization model for solving the imbalance problem by carrying out an operator-based relocation strategy. The objective of the optimization model is to maximize the total profit and determine the optimal relocation frequency. It is found that most of the shared bikes are possible to gather at one low-demand node eventually in the long run under the influence of the different arrival rates at different nodes, but the decrease of the number of bikes at the high-demand nodes is more sensitive to the unequal demands and may cause a great loss for operators, which should be payed attention to especially when solving the relocation problems.

Rainwater harvesting could be an optional water source to fulfil the emergency water demand in different setups. The aim was to assess if the rainwater harvesting potential for households and selected institutions were sufficient to satisfy the emergency water demand for the prevention of COVID-19 in Dilla town, Southern, Ethiopia. Rain water harvesting potential for households and selected institutions were quantified using 17 years’ worth of rainfall data from Ethiopian Metrology Agency. With an average annual rainfall of 1464 mm, households with 40 and 100 m2 roof sizes have a potential to harvest between 15.71-31.15 m3 and 41.73-82.73 m3 of water using Maximum Error Estimate. Meanwhile 7.2-39.7 m3 and 19.11-105.35 m3 of water can be harvested from the same roof sizes using Coefficient of Variation for calculation. Considering mean monthly rainfall, the health centres and Dilla University can attain 45.7% and 77% of their emergency water demand, while the rest of the selected institutions in Dilla Town can attain more than 100 % of their demand using only rainwater. Rain water can be an alternative water source for the town in the fight against COVID-19.

This paper investigates the use of deep learning techniques to perform energy demand forecasting. Specifically, the authors have adapted a deep neural network originally thought for image classification and composed of a convolutional neural network (CNN) followed by a multilayered fully connected artificial neural network (ANN). The convolutional part of the network was fed with a grid of temperature forecasting data distributed in the area of interest in order to extract a featured temperature. The subsequent ANN is then fed with this calculated temperature along with other data related to the timing of the forecast. The proposed structure was first trained and then used in a real setting aimed to provide the French energy demand forecast using ARPEGE forecasting weather data. The results show that the performance of this approach is in the line of the performance provided by the reference RTE subscription-based service, which opens the possibility to obtain high accuracy forecasting using widely accessible deep learning techniques through open-source machine learning platforms.

Modern energy systems collect high volumes of data that can provide valuable information about energy consumption. Electric companies can now use historical data to make informed decisions on energy production by forecasting the expected demand. Many deep learning models have been proposed to deal with these type of time series forecasting problems. Deep neural networks, such as recurrent or convolutional, can automatically capture complex patterns in time series data and provide accurate predictions. In particular, Temporal Convolutional Networks (TCN) are a specialised architecture that has advantages over recurrent networks for forecasting tasks. TCNs are able to extract long-term patterns using dilated causal convolutions and residual blocks, and can also be more efficient in terms of computation time. In this work, we propose a TCN-based deep learning model to improve the predictive performance in energy demand forecasting. Two energy-related time series with data from Spain have been studied: the national electric demand, and the power demand at charging stations for electric vehicles. An extensive experimental study has been conducted, involving more than 1900 models with different architectures and parametrisations. The TCN proposal outperforms the forecasting accuracy of Long Short-Term Memory (LSTM) recurrent networks, which are considered the state-of-the-art in the field.

Non-intrusive load monitoring (NILM) is a core technology for demand response (DR) and energy conservation services. Traditional NILM methods are rarely combined with practical applications, and most studies aim to decompose the whole loads in a household, which leads to low identification accuracy. In this paper, an NILM approach based on multi-feature integrated classification (MFIC) is explored, which combines some non-electrical features such as ON/OFF duration, usage frequency of appliances, and usage period to improve load differentiability. The implementation of MFIC algorithm is consistent with traditional event-based method. The uniqueness of our algorithm is that it designs an event detector based on steady-state segmentation and a linear discriminant classifier group based on multi-feature global similarity. Simulation results using an open-access dataset demonstrate the effectiveness and high accuracy of MFIC algorithm, with the state-of-the-art NILM methods as benchmarks.

Relationships between drought and fire danger indices are examined to 1) incorporate fire risk information into the National Integrated Drought Information System California-Nevada Drought Early Warning System and 2) provide a baseline analysis for application of drought indices into a fire risk management framework. We analyzed four drought indices that incorporate precipitation and evaporative demand (E₀) and three fire indices that reflect fuel moisture and potential fire intensity. Seasonally averaged fire danger indices were most strongly correlated to multi-scalar drought indices that use E₀ (the Evaporative Demand Drought Index [EDDI] and Standardized Precipitation Evapotranspiration Index [SPEI]) at approximately annual time scales that reflect buildup of antecedent drought conditions. Results indicate that EDDI and SPEI can inform seasonal fire potential outlooks at the beginning of summer. An E₀ decomposition case study of conditions prior to the Tubbs Fire in Northern California indicate high E₀ (97th percentile) driven predominantly by low humidity signaled increased fire potential several days before the start of the fire. Initial use of EDDI by fire management groups during summer and fall 2018 highlights several value-added applications, including seasonal fire potential outlooks, funding fire severity level requests, and assessing set-up conditions prior to large, explosive fire cases.

This paper investigates how blocks of buildings could fit into load shedding strategies. It focuses in particular on what could be the effects on peak shaving, occupants’ thermal comfort or CO2 emissions reduction and how to quickly quantify them. To achieve this goal, we focused on a new residential district, thermally fed by heat pumps. Four modeling approaches were confronted in order to estimate buildings' responses to load shedding orders. On the one hand, a quick estimation of the peak shaving impact can rely on experimental results if the buildings' envelope and uses of the experimentation match those of the study case. On the other hand, thermal simulation models allow us to assess thermal comfort while considering the building physical response. Finally, a hybrid modeling approach can provide a good compromise between modeling rapidity and accuracy of the impacts estimation. At district scale, it may be necessary to mix modeling approaches, from experimental results to detailed thermal models. Accuracy is not guaranteed for all approaches so that the choice should be made carefully in regards to study needs. However, results are sufficient to compare the effects of load shedding strategies on peak shaving, thermal comfort, and CO2 emissions reductions.

An energy diagnosis is a tool used to seek the improvement of energy saving measures, environmental conservation and energy efficiency, making relevant its implementation in any kind of buildings. For this article, an energy diagnosis of third level was carried out in buildings of the Instituto de Energías Renovables (IER) from Universidad Nacional Autónoma de México (UNAM) through survey and census of the 36 buildings in the IER, in order to characterize current patterns of energy consumption and demand, and generating specific strategies towards savings and energy efficiency, such as indicators and corrective proposals within and non-financial investment.

If the world’s countries seriously tackle the climate targets agreed in Paris, their citizens are likely to experience substantial changes in production, consumption and employment. We present a long-run post-Keynesian model for studying the potential implications of a major transition on macroeconomic stability and employment. It is a demand-led model in which firms have considerable but not absolute freedom to administer prices, while household consumption exhibits inertia. Firms continually seek input-saving technological improvements that, in the aggregate, tie technological progress to firms' cost structure. Together with firm pricing strategies and wage setting, the productivities of different inputs determine the functional income distribution. Saving and investment, and production and purchase of consumption goods, are undertaken by different economic actors, driven by income and capacity utilization, with the possibility that productive capacity exceeds, or falls short of, effective demand. The model produces business cycles and long waves driven by technological change. We present results for a “downshifting” scenario in which households voluntarily withdraw labor and discuss the implications of downshifting for stability, growth, and employment. We contrast the downshifting scenario with ones in which households reduce consumption without withdrawing from the labor pool.

Transdermal drug delivery (TDD) is one of the key approaches for treating diseases, avoiding first-pass effects, reducing systemic adverse drug reactions and improving patient compliance. Microneedling, iontophoresis, electroporation, laser ablation and ultrasound facilitation are often used to improve the efficiency of TDD. Among them, microneedling is a relatively simple and efficient means of drug delivery. Microneedles usually consist of micron-sized needles (50-900 μm in length) in arrays that can successfully penetrate the stratum corneum and deliver drugs in a minimally invasive manner below the stratum corneum without touching the blood vessels and nerves in the dermis, improving patient compliance. Hydrogel-forming microneedles (HFMNs) are safe, non-toxic, no residual matrix material, high drug loading capacity, controlled drug release and are suitable for long-term, multiple drug delivery. This work reviewed the characteristics of skin structure and transdermal drug delivery; introduced TDD strategies based on hydrogel microneedles; summarised the characteristics of HFMNs TDD systems and the evaluation methods of HFMNs; and the application of HFMNs drug delivery systems in disease treatment. The HFMNs drug delivery system has a wide scope for development, but the translation to clinical application still has more challenges.

Honey bees (Apis mellifera L.) express complex behavioral patterns (aggressiveness) to exhibit defensive mechanisms for their survival. Their phenotypic expression of aggressive behavior is influenced by internal and external stimuli. Knowledge of this behavior is recently important though beekeepers are still faced with the challenges of selecting aggressive and less-aggressive bred lines. Field evaluation of aggressiveness among bred lines of honey bees is required to overcome the challenges. Chemical cues (alarm pheromone and isopentyl acetate mixed with paraffin oil), physical and visual stimuli (dark leather suede, colony marbling and suede jiggling) were used to evaluate aggressiveness and orientation among five bred lines of honeybee colonies. Our results showed that both chemical assays recruited bees but the time of recruitment was significantly lower for alarm pheromone. Honeybees’ response to both assays culminated to stings which differed among bred lines for alarm pheromone and paraffin when colonies were marbled. Honeybee aggression varied among bred lines and was higher in more aggressive bred lines compared to less-aggressive bred lines. Our findings suggest that it is crucial to repeatedly evaluate orientation aggressiveness at the colony level and among bred lines when selecting breeding colonies.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

The interactions of chemotherapeutic drugs with nanocage protein apoferritin (APO) are the key features in the effective encapsulation and release of highly toxic drugs in APO-based controlled drug delivery systems. The encapsulation enables mitigating the drugs side effects, collateral damage to healthy cells, and adverse immune reactions. Herein, the interactions of anthracycline drugs with APO were studied to assess the effect of drug lipophilicity on their encapsulation excess n and in vitro activity. Anthracycline drugs, including doxorubicin (DOX), epirubicin (EPI), daunorubicin (DAU), and idarubicin (IDA), with lipophilicity P from 0.8 to 15, were investigated. We have found that in addition to hydrogen-bonded supramolecular ensemble formation with n = 24, there are two other competing contributions that enable increasing n under strong polar interactions (APO(DOX)) or under strong hydrophobic interactions (APO(IDA) of the highest efficacy). The encapsulation/release processes were investigated using UV-Vis, fluorescence, circular dichroism, and FTIR spectroscopies. In vitro cytotoxicity/growth inhibition tests and flow cytometry corroborate high apoptotic activity of APO(drugs) against targeted MDA-MB-231 adenocarcinoma and HeLa cancer cells, and low activity against non-tumorigenic MCF10A cells, demonstrating targeting ability of nanodrugs. A model for molecular interactions between anthracyclines and APO nanocarriers was developed, and the relationships derived compared with experimental results.

Objectives To determine the effects of omega-3 polyunsaturated fatty acids (ω-3 PUFA) from animal and plant sources on glucolipid metabolism and lipoprotein subfractions in type 2 diabetic patients with dyslipidemia. Methods Participants were recruited from the diabetes clinic at the Guanlin Hospital, Yixing City in Jiangsu province, China, from March 2017 through June 2017. Ninety participants were randomly assigned to take 3g/day fish oil (FO, containing EPA and DHA), 3g/day perilla oil (PO, containing ALA), or 3g/day blend oil containing fish oil and linseed oil (BO, containing EPA, DHA and ALA) for 3 months. The levels of serum glucose, glycated hemoglobin (HbA1c), C-peptide, triglyceride (TG), total cholesterol (TC), high-density lipoprotein (HDL), low-density lipoprotein (LDL), non-HDL, apolipoprotein A1 (Apo A1), apolipoprotein B (Apo B), lipoprotein a (Lp(a)), and free fatty acids were determined at baseline and after the 3 months. In addition, four fatty acids in serum and red blood cells membranes (RBCm) were analyzed using gas chromatography-mass spectrometry. The Lipoprint System was used to determine the lipoprotein subfractions. Results All 90 participants completed the final 3-month follow-up at the end of the study. After three months of intervention, blood glucose and HbA1c levels in the PO group were significantly lower than those at the baseline (p < 0.05). On the other hand, in the BO group, the HbA1c, non-HDL, Apo A1 and Lp(a) levels were significantly lower, while the C-peptide levels were significantly higher after intervention compared to the baseline (p < 0.05). In the FO group, the HbA1c and TG levels were significantly lower after the intervention compared to the baseline (p < 0.05). In addition, at the end of the study, there was significant increase in the levels of DPA and DHA in serum and RBCm of the FO group (p < 0.05), while in the BO group, there was significant increase in the levels of EPA, DPA and DHA in RBCm (p < 0.05). Finally, the FO group had the highest levels of large HDL subfractions compared to the BO and PO groups, but had the lowest levels of small HDL subfractions among the three groups. Conclusion For patients with diabetes, plant-derived ω-3 PUFAs are more effective at controlling blood glucose than animal-derived ω-3 PUFAs. However, animal-derived ω-3 PUFAs play a critical role in controlling blood lipids. Particularly, fish oil can effectively increase the beneficial large HDL subfractions and reduce the nonbeneficial small HDL subfractions. Both the animal- and plant-derived ω - 3 PUFAs have practical value in improving glucose and lipids metabolism in T2DM patients with dyslipidemia.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

This study investigates the relationship between housing prices and vacancy rates in Hong Kong, offering insights distinct from previous cross-sectional analyses. Addressing limitations in data availability and methodological approaches, the study examines annual data spanning multiple housing size categories to uncover nuanced dynamics in the housing market. Two major contributions emerge: firstly, the analysis reveals the price elasticity of vacancy, elucidating how housing prices respond to changes in vacancy rates over time. Secondly, by considering housing vacancy changes as outcomes of the interactions between supply and demand, the study challenges the conventional independence assumption between these variables. The results support the hypothesis that housing vacancies exert a negative impact on housing prices, holding other factors constant. These findings have significant implications for policymakers, urban planners, and real estate investors, providing valuable insights for crafting targeted interventions and informing investment decisions.