Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

The increase in tobacco production while ameliorating the condition of the participant households has caused challenges to stakeholders particularly those in the governance of forest resources upon which the sector is hinged. Massive deforestation has proceeded at an alarmingly high level, in a way that threatens the long term viability of the tobacco sector and sustainability of natural forest resources. The entrance of previously disadvantaged majority into the once minority-dominated tobacco sector (and economy) in a quest to improving their livelihoods, is driving forest landscape changes that pose inherent environmental challenges including climate change. This article adopts institutional and landscape approaches to explore and explain the drivers, nexus and implications of smallholder tobacco as a livelihood strategy to the forest landscape changes and the subsequent imperative for governance of the sustainable utilization of forest resources in Zimbabwe. Drawing on documentary evidence the paper concludes that this situation poses a dilemma to forest and livelihood policies, hence the need to examine new institutional and livelihood initiatives.

A simple, isocratic and robust RP-HPLC method for the analysis of azithromycin was developed, validated and applied for the analysis of bulk samples, tablets and suspensions. The optimum chromatographic conditions for separation were established as mobile phase comprising of acetonitrile-0.1M KH₂PO₄ pH 6.5-0.1M tetrabutyl ammonium hydroxide pH 6.5-water (25:15:1:59% v/v/v/v) delivered at a flow rate of 1.0 ml/min. The stationary phase consisted of reverse-phase XTerra^® (250 mm× 4.6 mm i.d., 5 µm particle size) maintained at a temperature of 43 °C with a UV detection at 215 nm. The method was found to be linear in the range 50-150% (r²=0.997). The limits of detection and quantification were found to be 0.02% (20 µg) and 0.078% (78 µg) respectively with a 100.7% recovery of azithromycin. Degradation products of azithromycin in acidic and oxidative environments at 37 °C were resolved from the active pharmaceutical ingredient and thus the method is fit for the purpose of drug stability confirmation.

Savannas and adjacent vegetation types like gallery forests are highly valuable ecosystems contributing to several ecosystem services including carbon budgeting. Financial mechanisms such as REDD+ have provided an opportunity for developing countries to alleviate poverty through conservation of its forestry resources. For availing this opportunity carbon stock assessments are essential. Therefore, a research study at two protected areas i.e. Nazinga Game Ranch and Bontioli Nature Reserve, in Burkina Faso was conducted with the objective of assessing carbon Mg C ha-1 in aboveground biomass (AGB)dry of trees in different formations of the south-sudanian savanna in Burkina Faso, West Africa. Similarly analysis of various vegetation parameters was also conducted to understand the overall vegetation structure of these two protected areas. For estimating AGBdry, existing allometric equation for dry tropical woody vegetation types was used. The Importance Value Index (IVI) and Family Importance Value (FIV) were estimated through standard procedures. Various linear and non-linear regression analyses were conducted to test the relationships between carbon and other parameters such as DBH, height and basal area (BA). The results showed that both sites collectively contain mean carbon of 3.41 ± 4.98 Mg C ha-1. Amongst different vegetation types, gallery forests recorded the highest mean carbon of 9.38 ± 6.90 Mg C ha-1. The highest IVI of 115.56 at Nazinga Game Ranch was recorded for Anogeissus leiocarpa. Similarly, highest IVI of 98.59 was recorded for Mitragyna inermis at Bontioli Nature Reserve. The highest FIV was recorded for Combretaceae for both of the sites. To our knowledge, this was the first study conducted to assess the carbon stocks at the two protected areas in southern Burkina Faso. The study therefore was an attempt for addressing the knowledge gap particularly on carbon stocks of protected savannas. It could serve as a baseline for carbon stocks for future initiatives such as payment for environmental services and REDD+ at these areas.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

This panel study investigates the relationship between green logistics indices, economic, environmental, and social factors in the perspective of Asian emerging economies. This study adopted FMOLS and DOLS methods to test research hypothesis, catering the problem of endogenity and serial correlation. The results suggest that logistics operations, particularly LPI2 (efficiency of customs clearance processes), LPI4 (quality of logistics services) and LPI5 (trade and transport-related infrastructure), are positively and significantly correlated with per capita income, manufacturing value added and trade openness. While, greater logistics operations are negatively associated with social and environmental problems including, climate change, global warming, carbon emissions, and poisoning atmosphere. In addition, human health is badly affected by heavy smog, acid rainfall, and water pollution. The findings further extend and reveal that political instability, natural disaster and terrorism are also a primary cause of poor economic growth and environmental sustainability with poor trade and logistics infrastructure. Further, the application of renewable energy resources and green practices can mitigate negative effects on social and environmental sustainability without compromising the performance of economic growth. There is very limited empirical work presented in literature using renewable energy and green ideology to solve macro-level social and environmental problems, while this study will assist the policymakers and researchers to understand the importance of green concept in improving countries’ social, economic and environmental performance.

Enveloped viruses represent a significant category of pathogens that cause serious diseases in animals. These viruses express envelope glycoproteins that are singularly important during infection of host cells by mediating fusion between the viral envelope and host cell membranes. Despite low homology at protein levels, three classes of viral fusion proteins have, as of yet, been identified based on structural similarities. Their incorporation into viral particles is dependent upon their proper sub-cellular localization after being expressed and folded properly in the endoplasmic reticulum (ER). However, viral protein expression can cause stress in the ER, and host cells respond to alleviate the ER stress in the form of the unfolded protein response (UPR); the effects of which have been observed potentiating or inhibiting viral infection. One important arm of UPR is to elevate the capacity of the ER-associated protein degradation (ERAD) pathway, which is comprised of host quality control machinery that ensures proper protein folding. In this review, we provide relevant details regarding viral envelope glycoproteins, UPR, ERAD, and their interactions in host cells.

Background: Rangeland degradation means that a reduction both in rank and status of general floral/ fauna composition, energy flow and biomass of a certain ecosystem. Objective: The review was conducted to assess rangeland degradation, cause and its impact on local livelihood in Yabello district and also suggests appropriate methods used to rehabilitate it. Methods: The data and literatures were collected from different both domestic and abroad researcher research result reviewed and internet sources. The research paper review mainly addresses concepts of rangeland degradation, major causes in tropics and Ethiopia particularly in Yabello rangelands, impacts of rangeland degradation, principles of rangeland restoration and common restoration techniques.Result: Based on those research papers and the current fact situations the major drivers leading to rangeland degradation includes climate change, overgrazing, bush encroachment, both human and livestock population pressure, drought, and government policy . Of all bush encroachment is becoming the major threat to Yabello rangelands. And this led to decline in rangeland condition, water potential, soil status, and animal performance, livestock holding at the household level and community become destitute and in the long run poverty. In spite of these impacts, the action of restoration techniques in the area is highly insufficient. Conclusion: Generally in order to address rangeland degradation problems, there is a strong need to coordination between the local community and the scientific community for sustainable land management trough post management techniques by applying reseeding technology.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Some studies have demonstrated that in vivo degradation processes are influenced by the material’s physico-chemical properties. The present study compares two hydroxyapatites manufactured on an industrial scale, deproteinized at low and high temperatures, and how physico-chemical properties can influence the mineral degradation process of material performance in bone biopsies retrieved 6 months after maxillary sinus augmentation. Residual biomaterial particles were examined by field scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) to determine the composition and degree of degradation of the bone graft substitute material. According to the EDX analysis, the Ca/P ratio significantly lowered in the residual biomaterial (1.08±0.32) compared to the initial composition (2.22±0.08) for the low-temperature sintered group, which also presented high porosity, low crystallinity, low density, a large surface area, and poor stability and a high resorption rate compared to the high-temperature sintered material. This demonstrates that variations in the physico-chemical properties of bone substitute material clearly influence the degradation process. Further studies are needed to determine whether the resorption of deproteinized bone particles proceeds slowly enough to allow sufficient time for bone maturation to occur.

The present study describes the activities performed to test a new method for measuring the mobility of polycyclic aromatic hydrocarbons (PAHs) in the solid phase of sediments within the context of environmental pollution risk assessment. The method is based on the design of a new configuration (new materials) of the commercial passive sampler Chemcatcher as probe for predicting the bioavailability of persistent organic pollutants in marine sediments (or in water saturated soils).

Arylmagnesium and -calcium reagents are easily accessible, however, ether degradation processes limit the storability especially of the calcium-based heavy Grignard reagents. Ortho-bound substituents with phosphanyl donor sites usually block available coordination sites and stabilize such complexes. The reaction of bromo-2,6-bis(diphenylphosphanylmethyl)benzene (1a) with magnesium in tetrahydrofuran yields [Mg{C₆H₃-2,6-(CH₂PPh₂)₂}₂] (2) after recrystallization from 1,2-dimethoxyethane. However, the similarly performed reduction of bromo- (1a) and iodo-2,6-bis(diphenylphosphanylmethyl)benzene (1b) with calcium leads to ether cleavage and subsequent degradation products. α-Deprotonation of THF yields 1,3-bis(diphenylphosphanylmethyl)benzene. Furthermore, the insoluble THF adducts of dimeric calcium diphenylphosphinate halides, [(thf)₃Ca(X)(µ-O₂PPh₂)]₂ [X = Br (3a), I (3b)], precipitate verifying ether decomposition and cleavage of P-C bonds. Ether adducts of calcium halides [such as [(dme)₂(thf)CaBr₂] (4)] form supporting the initial Grignard reaction and a subsequent Schlenk-type dismutation reaction.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

Fourteen (14) rack-mounted polycrystalline modules installed on the concrete roof of the solar energy applications laboratory at the Kwame Nkrumah University of Science and Technology (KNUST) in Ghana, a hot humid environment were assessed after 19 years of continuous outdoor expodure. The physical state of the modules was documented using a visual inspection checklist. They were further assessed by current-voltage (I-V) characterization and thermal imaging. The modules were found to be in good physical state, except some bubbles on front side and minor discolouration/corrosion at edge of the cells. Compared with reference values, the performance decline of the modules observed over the exposure period was: nominal power (P_nom), 21% to 35%; short circuit current (I_sc), 5.8% to 11.7%; open circuit voltage (V_oc) 3.6% to 5.6% and 11.9% to 25.7% for fill factor (FF). It is hoped that this study will provide some helpful information to project developers, manufacturers and the research community on the long-term performance of PV modules in Ghana.

Land degradation is a serious impediment to improving rural livelihoods in Eastern Africa. This paper identifies major land degradation patterns and causes, and analyzes the determinants of sustainable land management (SLM) in three countries (Ethiopia, Malawi and Tanzania). The results show that land degradation hotspots cover about 51%, 41%, 23% and 23% of the terrestrial areas in Tanzania, Malawi and Ethiopia respectively. The analysis of nationally representative household surveys shows that the key drivers of SLM in these countries are biophysical, demographic, regional and socio-economic determinants. Secure land tenure, access to extension services and market access are some of the determinants incentivizing SLM adoption. The implications of this study are that policies and strategies that facilities secure land tenure and access to SLM information are likely to incentivize investments in SLM. Local institutions providing credit services, inputs such as seed and fertilizers, and extension services must also not be ignored in the development policies.

Proteolysis Targeting Chimeras (PROTACs) describe compounds that bind to and induce degradation of a target by simultaneously binding to a ubiquitin ligase. More generally referred to as bifunctional degraders, PROTACs have led the way in the field of targeted protein degradation (TPD) with several compounds currently undergoing clinical testing. Alongside bifunctional degraders, single-moiety compounds, or molecular glue degraders (MGDs), are increasingly being considered as a viable approach for development of therapeutics, driven by advances in rational discovery approaches. This review focusses on drug discovery with respect to bifunctional and molecular glue degraders within the ubiquitin proteasome system, including analysis of mechanistic concepts and discovery approaches, with an overview of current clinical and pre-clinical degrader status in oncology, neurodegenerative and inflammatory disease.

In this paper, the influence of the various degradation conditions, on the molecular and supramolecular structure of polybutylene succinate (PBS) and polybutylene succinate adipate (PBSA) copolymer during degradation time is described. Experiment was carried out by the use injection molded samples and normalized conditions of biodegradation in soil, composting and artificial weathering. Materials were studied by using size-exclusion chromatography (SEC) coupled with multiangle laser light scattering (MALLS) detection and wide-angle X-ray diffraction (WAXD). Additionally, the physical and mechanical properties of the samples were determined. The performed experiments clearly show difference impact of selected degradation condition on the macroscopic, supramolecular and molecular parameters of studied aliphatic polyesters. The structural changes in PBS and PBSA explain the observed changes in the physical and mechanical properties of the obtained injection molded samples.

Many neurodegenerative diseases are characterised by impairment of protein quality control mechanisms in neuronal cells. Ineffective clearance of misfolded proteins by the proteasome, autophagy pathways and exocytosis leads to accumulation of toxic protein oligomers and aggregates in neurons. Toxic protein species affect various cellular functions resulting in the development of a spectrum of different neurodegenerative proteinopathies, including Huntington’s disease (HD). Playing an integral role in proteostasis, dysfunction of the ubiquitylation system in HD is progressive and multi-faceted with numerous biochemical pathways affected, in particular the ubiquitin proteasome system and autophagy routes for protein aggregate degradation. Unravelling the molecular mechanisms involved in HD pathogenesis of proteostasis provides insight in disease progression in HD as well as possible therapeutic avenues. Recent developments of potential therapeutics are discussed in this review.

Bamboo agroforestry is currently being promoted as a viable land use option to reduce dependence on natural forest for wood fuels in Ghana. To align the design and introduction of bamboo agroforestry in conformity with farmers’ needs, perceptions, skills and local cultural practices, information on its acceptability and adoption potential among farmers is necessary. It is therefore the objective of this study to (1) describe bamboo ethnobotany and (2) assess socioeconomic factors that affect the acceptability and adoption of bamboo and its integration into farming practices. Accordingly, information has been collected from 200 farmers in the dry semi-deciduous forest zone of Ghana. The study identified the socioeconomic risks and uncertainties as well as biophysical factors that are likely to influence the potential adoption of bamboo agroforestry in the study region. Gender, age, farmers’ known uses of bamboo, the practice of leaving trees on farmlands, farmers’ networking and access to extension services, land availability and ownership by farmers were identified as suitable predictor variables for the adoption of bamboo agroforestry. It is envisaged that bamboo agroforestry is a good bet in the DSFZ though there is the need to explore domestic energy (fuelwood) provision and substitution potential in order to have a broader picture of the technology.

This work updates the characterization of winter fish communities in salt marsh areas of Guadiana estuary (SE-Portugal) and discusses the potential risks of habitat dominance by a non-indigenous species (NIS). To this effect, six field campaigns were carried out during winter season targeting the collection of fish species. Individuals from seven different families (marine and estuarine) were collected although the community was dominated by two estuarine species – the native Pomatoschistus sp. (goby) and the NIS Fundulus heteroclitus (mummichog). Goby controlled the majority of salt marsh habitats, except one specific, marsh pool, where extreme environmental conditions were registered, namely high temperature and salinity. Such conditions may have boosted the intrusion of mummichog in this area. This species is well adapted to a wide range of abiotic factors enabling them to colonize habitats where no predators inhabit. Impacts of mummichog intrusion in the Guadiana salt marsh area are still unpredictable since this is the first recorded in such high density. Nevertheless, in scenarios of increased anthropogenic pressure and, consequently, habitat degradation, there is a potential risk of mummichog spread to other habitats and therefore compete for space and food resources with native species.

Polymer flooding is an established enhanced oil recovery (EOR) method, still many aspects of polymer flooding are not well understood. This study investigates the influence of mechanical degradation on flow properties of polymers in porous media. Mechanical degradation due to high shear forces may occur in the injection well and at the entrance to the porous media. The polymers that give high viscosity yields at a sustainable economic cost are typically large, MW > 10 MDa, and have wide molecular weight distributions. Both MW and the distributions are altered by mechanical degradation, leading to changes in the flow rheology of the polymer. The polymer solutions were subjected to different degrees of pre-shearing and pre-filtering before injected into Bentheimer outcrop sandstone cores. Rheology studies of injected and produced polymer solutions were performed and interpreted together with in-situ rheology data. The core floods showed a predominant shear thickening behavior at high flow velocities which is due to successive contraction/expansion flow in pores. When pre-sheared, shear thickening was reduced but with no significant reduction in in-situ viscosity at lower flow rates. This may be explained by reduction in the extensional viscosity. Furthermore, the results show that successive degradation occurred which suggests that the assumption of the highest point of shear which determines mechanical degradation in a porous media does not hold for all field relevant conditions.

In this paper, we propose an unsupervised blind restoration model for images in hybrid degradation scenes. The proposed model encodes the content information and degradation information of images and then uses the attention module to disentangle the two kinds of information. It can improve the ability of disentangled presentation learning for a generative adversarial network (GAN) to restore the images in hybrid degradation scenes, enhance the detailed features of restored image and remove the artifact combining the adversarial loss, cycle-consistency loss, and perception loss. The experimental results on the DIV2K dataset and medical images show that the proposed method outperforms existing unsupervised image restoration algorithms in terms of peak signal-to-noise ratio (PSNR), structural similarity (SSIM), and subjective visual evaluation.

Agricultural expansion is altering the provision of ecosystem services and seriously affecting the well-being of the indigenous communities still living in forests. In this paper, we evaluate the impact of forest loss and degradation on the indigenous forest dependent communities of Eastern Salta, Argentina, between 2001 and 2015. First, we identified the demand area of ten final ecosystem services for 202 indigenous communities using participatory mapping data. Second, we calculated the remaining usage area using a deforestation geodatabase based on Landsat images. Third, we analyzed the significance of trends in forest productivity processing vegetation spectral indices from MODIS products. By last, we detected changes in the growing season length by evaluating monthly trends in spectral indices. Our results show a reduction of 21% in the area used by indigenous communities for capturing final ecosystem services, and significant negative trends in forest productivity for the demand area of 64% of the communities, indicating that the area of use is not only being reduced, but also remnant forest area is being degraded and the growing season is being shortened. These aspects indicate an important loss in the provision of ecosystem services that deeply affects the wellbeing of indigenous communities.

Forest degradation is known to be widespread in the tropics, but is currently very poorly mapped, in part because there is little quantitative data on which satellite sensor characteristics and analysis methods are best at detecting it. To improve this, we used data from the Tropical Forest Degradation Experiment (FODEX) plots in the southern Peruvian Amazon, where different numbers of trees had been removed from four 1 ha forest plots, carefully inventoried by hand and Terrestrial Laser Scanning before and after the logging to give a range of biomass change (ΔAGB) values. We conducted a comparative study of six multispectral optical satellite sensors (WorldView-3, SkySat, SPOT-7, PlanetScope, Sentinel-2 and Landsat 8) at 0.3 – 30 m spatial resolution, to find the best combination of sensor and remote sensing indicator for change detection. Spectral reflectance, the Normalized Difference Vegetation Index (NDVI) and texture parameters were extracted after radiometric calibration and image preprocessing. The strength of the relationships between the change in these values and field-measured ΔAGB (computed in % ha−1) was analysed. The results demonstrate that: (a) texture measures correlates more with ΔAGB than simple spectral parameters; (b) the strongest correlations are achieved for those sensors with spatial resolutions in the intermediate range (1.5 - 10 m), with finer or coarser resolutions producing worse results, and (c) when texture is computed using a moving square window ranging between 9 - 14 m in length. Maps predicting ΔAGB showed very promising results using a NIR-derived texture parameter for 3 m resolution PlanetScope (R2 = 0.97 and RMSE = 1.80 % ha−1), followed by 1.5 m SPOT-7 (R2 = 0.74 and RMSE = 5.25 % ha−1) and 10 m Sentinel-2 (R2 = 0.71 and RMSE = 5.55 % ha−1). Texture models derived from 0.3 m WorldView-3 improved with increasing window size, with highest R2 of 0.62 and RMSE = 6.35 % ha−1 for a window of 14 m in length. The degradation in our field plots is invisible to the 30 m resolution Landsat data. Our findings imply that, at least for lowland Peru, low-medium intensity disturbance can be detected best in optical wavelengths using a texture measure derived from 3 m PlanetScope data. That such data are being collected daily, and currently released free as monthly mosaics over tropical forests as part of the Norway’s International Climate and Forest Initiative (NICFI), is excellent news for monitoring such degradation.

Covid-19 pandemic lockdown has slow down the world economic system. The pandemic has cleared the roads, close factories and grounded planes causing severe economic challenges. The damaging impact of the pandemic amid lockdown has been a blessing in guise for the environment because of significant drop in pollution level as transport and industrial sectors shutdown. Transport and industrial sectors are major contributors to environmental degradation through various emissions as a result of fossil fuel consumption. Energy consumed by transport and industrial sectors will have to shift to viable, readily available, economically and environmentally friendly with no carbon build up post Covid-19 pandemic. Hydrogen energy remains the best alternative option technologies containing green house gas emission and pollutions of several forms. Hydrogen holds the potential to provide a clean, reliable, renewable and economical source of energy for meeting the growing and unending global energy needs post pandemic. The present paper explores the economic feasibility and potential of hydrogen to serve as a competitive fuel option post pandemic. In this paper, the role of hydrogen as an energy carrier hydrogen economy structure, potential of hydrogen economy, hydrogen production methods, hydrogen application and the economic and environmental importance of hydrogen as a viable fuel option post covid-19 pandemic were discussed. There will be a surge in demand and investment for hydrogen economy post Covid-19.

Accurate forest reference and emission level (FRL, FREL) with related policies and regulations are the key determinants in establishing sustainable forest ecosystem management programmes (e.g. REDD+). This fundamental is for promoting and sustaining climate smart agricultural practices in a changing climate. With the aim to deliver better knowledge to the scientific community and policy makers on regulations and existing tools for more rigorous scientific communication when it comes to FRL and FREL accountability and policies. Thus, this review investigates forest in the changing climate and policies and underlines the performance of land use transition and intensity analysis towards deforestation with some key examples and achievements (e.g. Togo). Simply put, (i) forest as break of greenhouse gas (GHGs) and ecosystem regulator, (ii) policies and REDD+ actions, (iii) potential drivers and (iv) transition and intensity analysis approach for their accountability are discussed. In sum, impressive studies, policies and regulations are under initiations and implementations regarding the role, place and evaluation of forest losses and its ecosystem functions and services. However, there are still some gaps when it comes to: the choice of the evaluation methods in the real context of a specific ecosystem as well as the firm implementations of formulating policies in developing countries. This paper concludes with some policy measures for forest sustainability, carbon enhancement and accountability.

Land degradation monitoring and assessment in the Sahel zone has relied substantially on temporal trends of remote sensing-based vegetation indices, which are proxies for the bioproductivity of the land. However, prior studies have shown that negative or positive trends in bioproductivity are not necessarily associated with degradation or improvement of land condition. In this short communication, while acknowledging the contributions of remote sensing-based indices and global-scale datasets to dismantling an outdated desertification narrative, we argue that local land users have much to contribute to our understanding of land degradation, and particularly to ensuring that scientific assessments of degradation capture variables relevant to them. We used the participatory photo elicitation method in three sites in the Senegalese Ferlo in order to elicit local pastoralists’ perspectives on land degradation and identify the indicators that they use to characterize pasture quality, while empowering them to lead the discussion. The discussion revealed indicators far beyond bioproductivity, including livestock performance as well as composition and quality of the herbaceous and woody vegetative cover, invasive species, soil quality and water availability. We found that the pastoralists’ knowledge and interest in the issue could potentially be harnessed more systematically, and at larger scales, in order to build a spatially explicit field-based knowledge base of land degradation complementary to remote sensing-based maps of trends in bioproductivity. Such a dataset could serve as a standalone product or as a reference dataset for development and validation of remote sensing-based indicators.

This study investigates proximate drivers of cropland and forest degradation in Kloto district (Togo, West Africa) as, way of, exploring integrated sustainable landscape approaches in respect to socio-economic and environmental needs and requirements. Net change analysis of major cash and food crops based on three time steps Landsat data (1985–2002, 2002–2017 and 1985–2017) and quantitative analysis from participatory survey data with farmers and landowners are used. Study underlines poor agricultural systems and cassava farming as major impediments to alarming forest losses between 1985–2017. Significant net loss in forests cover by 23.6% and surface areas under cultivation of cocoa agroforestry and maize by 12.99 and 10.1% from 1985 to 2017, due to, intensive cassava cropping (38.78%) and settlement expansions (7.84%). Meanwhile, loss in forest cover between 2017 and 2002 was marginal (8.36%) compared to the period 1985–2002 for which the loss was considerable (15.24%). Based on participatory surveys, majority of agricultural lands are threatened by erosion or physical deterioration (67.5%), land degradation or salt deposits and loss of micro/macro fauna and flora at 56.7%, declining in soil fertility (32.5%), soil water holding capacity (11.7%) and changes in soil texture (3.3%). Majority of farmers adhere to the adoption of the proposed climate smart practices with emphasis on cost effective drip irrigation systems (45.83%), soil mulching (35%) and adoption of drought resilient varieties (29.17%) to anticipate drought spells adverse. The study concludes that low adoption of improved soil conservation, integrated water management and harvesting systems and low productive and adaptive cultivars entail extreme degradation of croplands and crops productivity decline. Therefore, farmers are forced to clear more forests in search of stable and healthy soils for production and extraction of forest products to meet their food demands and improve their livelihoods conditions. Capacity building on integrated pathways of soil and land management practices are therefore needed to ensure sustainable and viable socio-ecological systems at local scale.

Choice of the salts of therapeutic agents or active pharmaceutical ingredients (API) is based on the physicochemical properties of API and the dosage form considerations. The appropriate salt can have positive effect on overall therapeutic and pharmaceutical effects of API. However, the incorrect salt form can negatively affect the overall pharmaceutical outcomes of the API. This review addresses various criteria for choosing appropriate salt form along with the effect of salt forms on API’s pharmaceutical properties. In addition to comprehensive review of the criteria, this review also gives a brief historic perspective of the salt selection process.

In this study, functionalized-MWCNTs with 3-aminopropyltriethoxysilane (APTES) loaded titania nanoparticles (MWCNTs-APTES-TiO₂) were prepared to investigate their physicochemical properties and photocatalytic activity for methyl orange (MO) degradation. The TiO₂ nanoparticles, functionalized-MNCNT and composite powders were characterized by XRD, raman, and TEM. The results obtained proved that titania (TiO₂) nanoparticles was successfully loaded on APTES-MWCNTs. The best photocatalytic degradation of methyl orange solution under UV light irradiation was recorded over MWCNTs-APTES-TiO₂ (1:2), with 87% after 180 min. Kinetic analysis indicated that photocatalytic degradation of MO solution by MWCNTs-APTES-TiO₂ obeyed second-order kinetic model (R² > 0.95), supported by half-life equations and graph. The presence of carbon nanotubes accelerated the degradation of methyl orange due to inhibition of electron-hole recombination, the formation of additional hydroxyl radicals and functional groups of the latter had an inhibitory effect on the degradation of methyl orange. This study shows that the MWCNTs-APTES-TiO₂ nanocomposites exhibit promising photocatalytic degradation against methyl orange.

Plastics are extensively used due to their versatility, durability, and low cost. PET stands for Polyethylene terephthalate. PET plastic is widely used all over the world and has many applications ranging from water bottles to fabrics like polyester and many things in between. But its unrestrained use in every field is resulting in heaps and piles of non-biodegradable materials causing damage to the environment and causing pollution. The idea being proposed is to degrade the PET plastic biologically using different bacteria. The bacteria used in this process are Ideonella sakaiensis, Acetobacterium woodii, Pelotomaculum and Methanospirillum hungatei. PET plastic is degraded, yielding Terephthalic Acid (TPA) and Ethylene Glycol (EG) by the action of the bacterium I. sakaiensis. Degradation of EG by A. woodii results in the formation of acetate and ethanol. TPA is degraded by the action of the coculture of Pelotomaculum and M. hungatei thereby yielding methane and acetate. All these products formed have significant commercial uses in various industries. The complete process that is to be carried out can help in achieving sustainability by fulfilling various Sustainable Development Goals set by the United Nations.

In this work, we report the fabrication of the new heterojunction of two 2D hybrid layered semiconductors, ZnO(stearic acid)/V₂O₅(hexadecylamine), and its behavior in the degradation of aqueous methylene blue under visible light irradiation. The optimal photocatalyst efficiency, reached at a ZnO(stearic acid)/ V₂O₅(hexadecylamine) ratio of 1:0.25, results to be about six times higher than that of pristine zinc oxide. Reusability test shows that after three photocatalysis cycles no significant changes in neither the dye degradation efficiency loss nor photocatalyst structure occur. Visible light photocatalytic performance observed indicates there is synergetic effect between both 2D nanocomposites used in the heterojunction. The visible light absorption enhancement promoted by the narrower bandgap V₂O₅ based components; an increased photo generated charge separation favored by extensive interface area; and abundance of hydrophobic sites for dye adsorption appear as probable causes of the improved photocatalytic efficiency in this hybrid semiconductors heterojunction. Estimated band-edge positions for both conduction and valence band of semiconductors together with experiments using specific radical scavengers allow a plausible photodegradation mechanism.

Targeted Protein Silencing (TPS) is an elegant approach to investigate protein function and its role in the cellular landscape, overcoming limitations of genetic perturbation strategies. In contrast to CRISPR/Cas9 and RNA interference, these systems act in a reversible manner and reduce off-target effects. Several TPS have been developed and wisely improved, including compartment delocalization tools and protein degradation systems. In this review, we focus on Anchor-Away, deGradFP, auxin inducible degron (AID) and dTAG technologies, and discuss their recent applications and advances. Finally, we propose Nano-Grad, a novel nanobody-based protein degradation tool to specifically proteolyze endogenous tag-free target protein.

Glyphosate-based herbicide products are the most widely used broad-spectrum herbicides in the world for post-emergent weed control. There are ever-increasing concerns that glyphosate, if not used judiciously, may cause adverse non-target impacts in agroecosystems. The purpose of this brief review is to present and discuss the state of knowledge with respect to its persistence in the environment, possible effects on crop health, and impacts on crop nutrition.

The ternary Bi2MoO6-reduced graphene oxide (rGO)-TiO2 catalyst were synthesized using a simple hydrothermal method. The improvement of the photocatalytic decomposition efficiency of Bi2MoO6-rGO-TiO2 composite is 92.3% than the pure and binary photocatalyst. The effects of operational parameters like catalyst ratio, the different catalyst, different ratio rGO and different pH, have been analyzed. As prepared ternary photocatalyst is low Photoluminescence and high photocurrent density responsible, it exhibited that photon-induced electron and hole-recombination were suppressed and also charged separation is effective. The present study shows the rGO is an excellent electron transfer performance and enhanced the photocatalytic reaction stability.

Abstract: Targeted ubiquitination and proteasomal degradation regulates various cellular pathways, and the discovery that CPT induced rapid proteasomal degradation of topoI is the primary mechanism of CPT resistance was novel and compelling. CPTs are used extensively to treat various solid tumors like colorectal, gastric, pancreatic, ovarian and small cell lung cancer. The response rate is low and the classical mechanisms of drug resistance are yet to be validated. Remarkably, CPT resistant cells degrade topoI rapidly by UPP and recently we’ve published the molecular determinants of this pathway. To further understand the UPP mediated CPT resistance mechanism we used targeted proteasome prohibition by ixazomib (MLN9708) to stabilize topoI and determine its impact on CPT resistance. CPT resistant and sensitive cancer lines were both treated with ixazomib in combination with CPT. The CPT induced rate of topoI degradation, and its stabilization by ixazomib, was visualized and estimated by immunohistochemistry, immunofluorescence and immunoblotting assays, MTT and subG1 assays provided the drug sensitivity. Our results demonstrate that cells that degrade topoI rapidly are very resistant to CPT, and ixazomib significantly inhibits CPT induced topoI degradation. Notably, inhibition of proteasomal degradation by ixazomib overcomes the drug resistance and sensitizes the cells for CPTs.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Water soluble polymers have gained an increasing interest in enhanced oil recovery (EOR) processes, especially as polymer flooding. Despite the fact that the flow of polymer in porous medium has been a research subject for many decades with numerous publications, there are still some research areas that need progress. The prediction of polymer injectivity remains elusive. Polymers with similar shear viscosity might have different in-situ rheological behaviors and may be exposed to different extent of mechanical degradation. Hence, determining polymer in-situ rheological behavior is of great significance for defining its utility. In this study, an investigation of rheological properties and mechanical degradation of different HPAM (partially hydrolyzed polyacrylamide) polymers was performed using Bentheimer sandstone outcrop cores. Results show that, HPAM in-situ rheology is different from bulk rheology measured in rheometer. Specifically, shear thickening behavior occurs at high rates, and near-Newtonian behavior is measured at low rates in porous media. This deviates strongly from measurements in the rheometer. Polymer molecular weight and concentration influence its viscoelasticity and subsequently its flow characteristics in porous media. Exposure to mechanical degradation by flow at high rate through porous media leads to significant reduction in shear thickening and thereby improved injectivity. More importantly, the degraded polymer maintained in-situ viscosity at low flow rates indicating that improved injectivity can be achieved without compromising viscosity at reservoir flow rates. This is explained by reduction in viscoelasticity. Mechanical degradation also leads to reduced residual resistance factor (RRF), especially for high polymer concentrations. For some of the polymer injections, successive degradation (increased degradation with transport length in porous media) was observed. The results presented here may be used to optimize polymer injectivity.

Organisms release their nucleic acid in the environment including the DNA and RNA which can be used to detect their presence. eDNA/eRNA techniques are being used in different sectors to identify organisms from soil, water, air, and ice since long. The advancement in technology led to easier detection of different organisms without impacting the environment and the organism itself. These methods are being employed in different areas including surveillance, history, and conservation. eDNA and eRNA methods are being extensively used in aquaculture and fisheries setting to understand the presence of different fish species and pathogens in water. However, there are some challenges associated with the reliability of the results because of the degradation of nucleic acid by several factors. In aquaculture there are several diseases and parasites detected with these methods. In this review we discuss different aquaculture diseases and parasites detected with eDNA/eRNA approach and the fate of these nucleic acids when subjected to different water quality and environmental parameters. This review intends to help the researcher about the potential of eDNA/eRNA based detection of pathogens in aquaculture; this will be useful to predict the potential outbreak before it occurs. Along with that this paper intends to make people understand several factors that degrade and can hamper the detection of these nucleic acids.

Magnesium-silver alloys are of high interest for the use as temporary bone implants due to their antibacterial properties in addition to biocompatibility and biodegradability. Thin wires in particular can be used for scaffolding, but the determination of their degradation rate and homogeneity using traditional methods is difficult. Therefore, we have employed 3D imaging using X-ray near-field holotomography with sub-micrometer resolution to study the degradation of thin (250 μm diameter) Mg-2Ag and Mg-6Ag wires. The wires were studied in two states, recrystallized and solution annealed to assess the influence of Ag content and precipitates on the degradation. Imaging was employed after degradation in Dulbecco’s modified Eagle’s medium and 10% fetal bovine serum after 1 to 7 days. At 3 days of immersion the degradation rates of both alloys in both states were similar, but at 7 days higher silver content and solution annealing lead to decreased degradation rates. The opposite was observed for the pitting factor. Overall, the standard deviation of the determined parameters was high, owing to the relatively small field of view during imaging and high degradation inhomogeneity of the samples. Nevertheless, Mg-6Ag in the solution annealed state emerges as a potential material for thin wire manufacturing for implants.

Acrylamide (AA) present in food is considered a harmful compound for humans, but it exerts impact on microorganisms too. The aim of the study was to evaluate the impact of AA (at conc. 0-10 µg/mL) on the growth of bacteria (Leuconostoc mesenteroides, Lactobacillus acidophilus LA-5) and yeasts (Saccharomyces cerevisiae, Kluyveromyces lactis var. lactis), which naturally occur in food products. Moreover, we decided to verify whether these microorganisms could decompose acrylamide. Our results proved that AA can stimulated the growth of L. acidophilus and K. lactis. We have also reported, to the best of our knowledge for the first time, that probiotic strain of bacteria L. acidophilus LA-5 is able to degrade AA by amidase production and hence can utilize AA as a source of carbon and nitrogen if they lack in the environment. The conducted Response Surface Methodology indicated that pH as well as incubation time and temperature significantly influenced the amount of ammonia released from acrylamide by the bacteria. Concluding, our studies suggest that some strains of bacteria present in milk fermented products can exert additional beneficial impact by acrylamide degradation and preventing against its harmful impact on human body and other members of intestinal microbiota.

Biochar is a carbon allotrope obtained by pyrolysis of biomass, usually agro-waste. Owing to the demand for sustainable development, biochar is continuously raising much hope in the scientific community. However, in order to impart it with new properties, its modification is required, either in situ during pyrolysis, or after the carbonization process. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticle-loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials bare biochar, copper-loaded and nickel-loaded biochar were prepared at 400 °C under a stream of dinitrogen from olive pit powder particles impregnated first with citric acid (CA), and then with copper and nickel nitrates. We have employed citric acid in the process in order to check its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped, bimetallic copper/nickel nanoparticles. Large 450-500 nm-sized agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni=10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nano-raspberries (1748 nm in size) which are agglomerates of individual 10-20 nm-sized CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be attracted efficiently with a magnet, but not B-CA@CuNi10/1 due to a low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times with exhibit as fast discoloration catalysis performance. This paper stresses the important role of citric acid in shaping the bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and to enable faster catalysed discoloration of organic dye solution.

Abstract: Green walls and green dams are increasingly being considered as part of many nation-al and international desertification initiatives. This paper studies the spatiotemporal evolution of the green dam in the Moudjbara region (Djelfa Province, Algeria) from 1972 to 2019 by using Landsat imagery, Land Change Modeler and Open Land package. The future evolution of pine plantations for the year 2029 was also forecasted, based on an anthropogenic scenario (i.e., an-thropogenic pressure is the main driver of the green dam destruction). Our findings revealed that the green dam project was successful for a few years, but after that, pine plantations deteri-orated significantly due to forest harvesting, livestock overgrazing, and the proliferation of the pine caterpillar processionary, which destroyed most of the reforestation. Land Change Modeler predicted a huge degradation of pine plantations for the year 2029, and if the deforestation con-tinues at the same rate, the green dam will disappear in the Moudjbara region during the next few decades. Aware of this threat, the Algerian authorities are now planning to reforest more than 1.2 million ha under the latest rural renewal policy by introducing new principles related to sustainable development, fighting desertification, and climate change adaptation

This study was conducted to improve the white index (WI) by preparing thermally expandable microspheres (TEMs) for wallpaper. The thermal properties, foam expansion ratio and WI were studied depending on the particle size of colloidal silica in the preparation of TEMs. As a result, the TEMs with small particles of colloidal silica showed the best results for whiteness and yellowing. Additionally, TGA results indicated that it was highly possible that colloidal silica with small particle sizes was physically or chemically attached to the surface of the TEMs that led to an improvement in whiteness at high temperatures.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

In this paper, by developing a mathematical model, the operating temperature of perovskite solar cells (PSCs) under different operating conditions has been calculated. It is found that by reducing the density of tail states at the interfaces, acting as recombination centres, through some passivation mechanisms, the operating temperature can be reduced significantly at higher applied voltages. The results show that if the density of tail states at the interfaces is reduced by three orders of magnitude through some passivation mechanisms, then the active layer may not undergo any phase change up to an ambient temperature 300 K and it may not degrade up to 320 K. The calculated heat generation at the interfaces at different applied voltages with and without passivation shows that the heat generation can be reduced by passivating the interfaces. It is expected that this study may provide a deeper understanding of the influence of interface passivation on the operating temperature of PSCs.

In most Eukaryotes, ubiquitin either exists as free monoubiquitin or as a molecule that is covalently linked to other proteins. These two forms cycle between each other and due to the concerted antagonistic activity of ubiquitylating and deubiquitylating enzymes, an intracellular ubiquitin equilibrium is maintained that is essential for normal biological function. However, measuring the level and ratio of these forms of ubiquitin has been difficult and time consuming. In this paper, we have adapted a simple immunoblotting technique to monitor ubiquitin content and equilibrium dynamics in different developmental stages and tissues of Drosophila. Our data show that the level of total ubiquitin is distinct in different developmental stages, lowest at the larval-pupal transition and in three days old adult males, and highest in first instar larvae. Interestingly, the ratio of free mono-ubiquitin remains within 30-50% range of the total throughout larval development, but peaks to 70-80% at the larval-pupal and the pupal-adult transitions. It stays within the 70-80% range in adults. In developmentally and physiologically active tissues, the ratio of free ubiquitin is similarly high, most likely reflecting a high demand for ubiquitin availability. We also used this method to demonstrate the disruption of the finely tuned ubiquitin equilibrium by the abolition of proteasome function or the housekeeping deubiquitylase, Usp5. Our data support the notion that the ubiquitin equilibrium is regulated by tissue- and developmental stage-specific mechanisms.

(1) Teeth, represent in humans the most resilient tissues. However, exposure to concentrated acids might lead to their obliteration, thus making human identification difficult. Teeth often contain dental restorations from materials that are even more resilient to acid impact. This paper introduces novel method of 3D reconstruction of dental patterns as a crucial step for digital identification with dental records.; (2) With combination of modern methods of Micro-Computer Tomography, Cone Beam Computer Tomography, Attenuated Total Reflection in conjunction with Fourier-Transform Infrared Spectroscopy and Artificial Intelligence Convolutional Neural Network algorithms, the paper presents the way of 3D dental pattern reconstruction and human remains identification. Research studies morphology of teeth, bone, and dental materials (Amalgam, Composite, Glass-ionomer cement) under different periods of exposure to 75% sulfuric acid; (3) Results reveal significant volume loss in bone, enamel, dentine, and as well glass-ionomer cement. Results also reveal significant resistance of composite and amalgam dental materials to sulfuric acid impact, thus serving as strong parts in the dental pattern mosaic. Paper also introduces probably first successful artificial intelligence application in automated forensic CBCT segmentation.; (4) Interdisciplinary cooperation utilizing mentioned technologies can solve problem of human remains identification with 3D reconstruction of dental patterns and their 2D projections over existing ante-mortem records.

HIF-1α is a master regulator of oxygen homeostasis involved in different stages of cancer development. Thus, HIF-1α inhibition represents an interesting target for anti-cancer therapy. It was recently shown that HIF-1α interaction with NQO1 inhibits its proteasomal degradation, thus suggesting that targeting the stability of NQO1 could led to destabilization of HIF-1α as a therapeutic approach. Since the molecular interactions of NQO1 with HIF-1α are beginning to be unraveled, we review here our current knowledge on the intracellular functions and stability of NQO1, its pharmacological modulation by small ligands, and the molecular determinants of its roles as a chaperone of many different proteins including cancer-associated factors such as p53 and p73α. This knowledge is then discussed in the context of potentially targeting the intracellular stability of HIF-1α by acting on its chaperone, NQO1. This could result in novel anti-cancer therapies.

Worldwide the steel corrosion is one of the greatest deterioration problems for reinforced concrete structures. Comparing some literature experimental results with a complex FEM model, the present paper points out the principal aspects those characterize the static behavior of RC elements damaged by corrosion. Moreover, the non-dimensional abaci defined for some specific case studies finalized to the evaluation of the residual flexural strength of corroded elements highlight the dangerousness of the corrosion degradation if the failure of the element is governed by the steel

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at &lt;2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

In this investigation, polymethyl methacrylate (PMMA) was mixed with cyclic olefin copolymer (COC) because of its hardness, strength, and transparency properties. The results of thermal analysis through TGA and DTG showed that the thermal properties of the alloy are improved using 40% cyclic olefin copolymer. Kinetics of thermal degradation (pyrolysis) of polymers have been studied and analyzed and thermal pyrolysis of polymethyl methacrylate and cyclic olefin copolymer thermoplastic polymer was conducted. The computation of kinetic analysis is measured along with the different methods used to study the kinetics. The activation energy (E) of degradation of studied materials was estimated using Ozawa Flynn and Wall (OFW), Starink and Kissinger’s methods, and evaluation of three kinetic parameters taken appropriate kinetic model in terms of percent change for both types of polymers have been proposed, and finally, simulated curves were compared with the experimental curves. Both mechanisms of degradation for COC and PMMA under nitrogen atmosphere will reflect intramolecular transfer and random scission of the main chain.

In manual maintenance inspections of large-scaled photovoltaic (PV) or rooftop PV systems, several days are required to survey the entire PV field. To improve reliability and shorten the amount of time involved, this study proposes an electrical examination based method for locating multiple faults in the PV array. The maximum power point tracking (MPPT) algorithm is used to estimate the maximum power of each PV panel; this is then compared with metering the output power of PV array. Power degradation indexes are parameterized to quantify the degradation between maximum power and metered output power. Bidirectional hetero-associative memory (BHAM) networks are then used to locate multiple faults within the entire PV field. For a rooftop PV system with two strings, as seen in Figure 1, experimental results demonstrate that the proposed model has computational efficiency for real-time applications and that its algorithm is easily implemented in a mobile intelligent vehicle.

In Nigeria, desertification has become one of the most pronounced ecological disasters, with the impacts mostly affecting eleven frontline States. This has been attributed to a range of both nat-ural and man-made factors. This study applied a remote sensing-based change detection and indicator analysis to explore land use/land cover changes and detect major conversions from ecologically active land covers to sand dunes. Results indicate that areas covered by sand dunes (a major indicator of desertification) have doubled over the 25 years under consideration (1990 to 2015). Although about 0.71 km2 of dunes have been converted to vegetation, indicative of the success of various international, national, local, and individual afforestation efforts, conversely about 10.1 km2 of vegetation were converted to sand dunes, implying around 14 times more de-forestation compared to afforestation. Juxtaposing the progression of sand dune with climate records of the study area and examining the relationship between indicators of climate change and desertification suggested a mismatch between both processes as increasing rainfall and lower temperatures observed in 1994, 2005, 2012, and 2014 did not translated into positive feedbacks for desertification in the study area. On average, our results reveal that sand dune is progressing at a mean annual rate of about 15.2 km2 in the study area. Based on this study’s land cover change, trend and conversion assessment, visual reconciliation of climate records with land cover data, statistical analysis, observations from ground-truthing, as well as previous literature, it can be inferred that desertification in Nigeria is less a function of climate change, but more a product of human activities driven by poverty, population growth and failed government policies. Further projections by this study also reveal a high probability of more farmlands being converted to sand dunes by the year 2030 and 2045 if current practices prevail.

Up to 13 million tons of plastic waste are estimated to enter the oceans every year. A generally accepted picture based on an increasing number of environmental studies suggests that the largest fraction of it consists or is rapidly degraded into microplastics (MPs). Most of the analytical studies focused on MPs are based on the detection and identification of the polymers. On the other hand, plastic debris in the environment undergo chemical (mainly photoxidative) and physical degradation processes leading not only to fragmentation but also to the formation of leachable, soluble and/or volatile degradation products that are released in the environment. The formation of such low molecular weight species is generally neglected in the studies on MPs even if these compounds, released in the environment from the plastics debris, may pose even higher risks for the environment and for the biota than the MPs particles themselves, risks that are far from being understood and assessed. In this study we performed the analysis of reference MPs - polymer micropowders obtained by grinding a set of five polymer types down to final size in the 857-509 μm range, namely high- and low-density polyethylene (HDPE and LDPE, respectively), polystyrene (PS), polypropylene (PP), and polyethylene terephthalate (PET). The reference MPs were artificially aged in a Solar-Box and their degradation products were analyzed to investigate their degradation processes. In particular, a systematic and thorough characterization of the aged (photo-oxidized) MPs and of their low molecular weight and/or highly oxidized fraction extractable in polar organic solvents was performed. For this purpose, the artificially aged MPs were subjected to selective extraction with organic solvent that are non-solvents for the virgin polymers, targeting selective recovery of the low molecular weight fractions generated during the artificial aging. Analysis of both the extractable fractions and the residues was carried out by a multi-technique approach combining evolved gas analysis-mass spectrometry (EGA-MS) and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). Up to 18 wt% of newly extractable, low molecular weight fraction was recovered from the photo-aged MPs, depending on the polymer type. The results highlight the need for more extensive studies about the potential harmfulness of the oxidation products (molecular and oxidized oligomeric species) that may leach out from plastic debris during their permanence in the environment.

This paper aims to provide an overall review of degradation, damage evolution and fatigue models in the literature of various engineering materials, mostly metals, and composites.

Deforestation and forest degradation mostly caused by human interventions affects the capacity of forest ecosystem to provide ecosystem services and livelihood benefits. Forest Land Restoration (FLR) is an emerging concept which focuses on the improvement of ecosystem as well as livelihood of the people at the landscape level. Nepal has successfully recovered degraded forest land mainly from the hilly region through forest restoration initiatives especially community based forestry. However, the Terai region is still experiencing deforestation and forest degradation. This study navigated the gaps related to forest restoration in the existing policies and practices and revealed that the persistence of deforestation and forest degradation in Terai is a result of a complex socio-economic structure, limitation of government to implement appropriate management modality, unplanned infrastructure, and urban development. We suggest that forest restoration should focus on ecological and social wellbeing pathways at the landscape level, to reverse the trend of deforestation and forest degradation in the Terai regions of Nepal. The study provides a critical insight to the policy makers and practitioners of Nepal and other countries (with similar context) who are engaged in forest/ecosystem restoration enterprise.

Land degradation a serious and nationwide environmental concern in Ethiopia. The problem is its iterative relationship between land degradation, climate change, and agriculture, exacerbating one another via negative and positive feedback loops. Due to the need for an efficient response to land degradation in the country, different sustainable land management practices have been implemented since the late 1980s. The objective of this study was to analyze land degradation neutrality status using remote sensing data in the study area. We have studied the land degradation neutrality conditions of the North Wello Zone by using indicators data, namely land cover change, land productivity dynamics, and soil organic carbon stock. The result shows that the settlement areas consistently expanded at the fifth speed (2010-2018) from 1995 to 2010. Between 1995 and 2010, forestland declined by 18 percent, while an increasing trend of 26.8 percent from 2010 to 2018. The assessment results also indicate that 52.8 percent of the total area is stable and characterized by less stressed land productivity. The soil organic carbon is comparatively abundant in the high and midland vegetation areas but very thin in lowland areas. Most of the highland and midland parts of the study areas are in the conditions of stable and increasing land productivity with high biomass and soil organic content. However, most lowland areas showed a decline in land productivity conditions.

A novel cytoplasmic dye decolorizing peroxidase from Dictyostelium discoideum was investigated that oxidizes anthraquinone dyes, lignin model compounds and general peroxidase substrates like ABTS efficiently. Unlike related enzymes, an aspartate residue replaces the first glycine of the conserved GXXDG motif in Dictyostelium DyPA. In solution, Dictyostelium DyPA exists as a stable dimer with the side chain of Asp146 contributing to the stabilization of the dimer interface by extending the hydrogen bond network connecting two monomers. To gain mechanistic insights, we solved the Dictyostelium DyPA structures in the absence of substrate as well as in the presence of potassium cyanide and veratryl alcohol to 1.7, 1.85, and 1.6 Å resolution, respectively. The active site of Dictyostelium DyPA has a hexa-coordinated heme iron with a histidine residue at the proximal axial position and either an activated oxygen or CN^- molecule at the distal axial position. Asp149 is in an optimal conformation to accept a proton from H₂O₂ during the formation of compound I. Two potential distal solvent channels and a conserved shallow pocket leading to the heme molecule were found in Dictyostelium DyPA. Further, we identified two substrate-binding pockets per monomer in Dictyostelium DyPA at the dimer interface. Long-range electron transfer pathways associated with a hydrogen-bonding network that connects the substrate-binding sites with the heme moiety are described.

In this work, pure TiO₂ and nano-magnetic of Fe₃O₄/TiO₂ were synthesized for degradation of 2,4-dichlorophenol (2, 4-DCP) as an organic pollutant. A range of analytical techniques including XRD, DRS, FESEM, and VSM were employed to reveal the crystal structure, morphology and property of the nanocomposite. The XRD results showed the prepared samples including 100% anatase phase. We obtained the band gap energy 2.9 and 2.8 eV for pure TiO₂ and Fe₃O₄/TiO₂ respectively. VSM results demonstrate that easy, fast separation and redispersion of Fe₃O₄/TiO₂ sample can be realized. We obtained 62% and 31% degradation of 2,4-DCP in the presence of Fe₃O₄/TiO₂ and pure TiO₂ under visible light respectively.

Herewith we report a facile synthesis of zinc oxide doped with (5, 10, 15, and 20 wt%) titanium oxide nanocomposites in gelatin under ultra-sonication. The X-ray diffraction (XRD) data revealed ZnO the formation in addition to a rutile phase TiO2. The ZnO phase size decreased, and the rutile TiO2 phase increased with a TiO2 loading increment. The scanning electron microscopy (SEM) displayed a combination of spherical and hexagonal particles with a 60 – 80 nm size distribution. The prepared nanostructures photocatalytic activity was assisted using Rhodamine B dye, where they showed enhanced photodegradation competence under visible light irradiation. The kinetics of photodegradation followed the first-order kinetics with the 20 % wt sample having the maximum activity. The mechanistic investigation revealed the dominance of h+ and •O2- species during the dye photodegradation. The results indicate the potential application of such gelatin stabilized nanostructures for dye illumination from aqueous solutions under sunlight.

Four decades of proteasome research have yielded extensive information on ubiquitin-dependent proteolysis. The archetype of proteasomes is a 20S barrel-shaped complex that does not rely on ubiquitin as a degradation signal but can degrade substrates with a considerable unstructured stretch. Since roughly half of all proteasomes in most eukaryotic cells are free 20S complexes, ubiquitin-independent protein degradation may coexist with ubiquitin-dependent degradation by the highly regulated 26S proteasome. This article reviews recent advances in our understanding of the biochemical and structural features that underlie the proteolytic mechanism of 20S proteasomes. The two outer α-rings of 20S proteasomes provide a number of potential docking sites for loosely folded polypeptides. The binding of a substrate can induce asymmetric conformational changes, trigger gate opening, and initiate its own degradation through a protease-driven translocation mechanism. Consequently, the substrate translocates through two additional narrow apertures augmented by the β-catalytic active sites. The overall pulling force through the two annuli results in a protease-like unfolding of the substrate and subsequent proteolysis in the catalytic chamber. Although both proteasomes contain identical β-catalytic active sites, the differential translocation mechanisms yield distinct peptide products. Non-overlapping substrate repertoires and product outcomes rationalize cohabitation of both proteasome complexes in cells.

The plant-microbe-soil nexus is critical in maintaining biogeochemical balance of the biosphere. However, soil loss and land degradation are occurring at alarmingly high rates, with soil loss exceeding soil formation rates. This necessitates evaluating marginal soils for their capacity to support and sustain plant growth. In a greenhouse study, we evaluated the capacity of marginal incipient basaltic parent material to support native plant growth, and the associated variation in soil microbial community dynamics. Three plant species, native to the Southwestern Arizona-Sonora region were tested with three soil treatments including basaltic parent material, parent material amended with 20% compost, and potting soil. The parent material with and without compost supported germination and growth of all the plant species, though germination was lower than the potting soil. A 16S rRNA amplicon sequencing approach showed Proteobacteria to be the most abundant phyla in both parent material and potting soil, followed by Actinobacteria. Microbial community composition had strong correlations with soil characteristics but not plant attributes within a given soil material. Predictive functional potential capacity of the communities revealed chemoheterotrophy as the most abundant metabolism within the parent material, while photoheterotrophy and anoxygenic photoautotrophy were prevalent in the potting soil. These results show that marginal incipient basaltic soil has the ability to support native plant species growth, and non-linear associations may exist between plant-marginal soil-microbial interactions.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

Leishmania species are parasitic protozoans which cause leishmaniasis affecting millions of people worldwide. Sterols are important components of plasma and organellar membranes and serve as precursors for the synthesis of signaling molecules. In contrast to animals, Leishmania do not produce cholesterol but instead synthesize ergostane-based sterols. C14-demethylase is a key enzyme involved in the biosynthesis of sterols in Leishmania parasites and an important drug target. Its inactivation leads to multiple defects including increased plasma membrane fluidity, mitochondrion dysfunction, hypersensitivity to stress and reduced virulence. In this study, we revealed a novel role for sterol synthesis in the maintenance of RNA stability and translation. Sterol alteration in C14-demethylase knockout mutant leads to increased RNA degradation, reduced translation and impaired heat shock response. Thus, sterol biosynthesis plays an unexpected role in global gene regulation in Leishmania parasites.

Polymeric drag reducers have been developed over many years due to the great number of practical applications. In all of them, the molecular stability is an essential requirement. Usually, polymers break down under turbulent flows, which causes a decrease in their efficiency as drag reducers. Besides that, some specific applications, in agro and biomedical fields, impose a specific requirement that must be fulfilled, which is the use of non-toxic materials. A suitable stable material that is elected to accomplish this necessity is the mucilage of aloe vera, which is a bio-polymer that can be used as an alternative to the synthetic ones. Here, we investigate the role played by the aging of aloe vera on its capacity to reduce drag. The results obtained by ¹H nuclear magnetic resonance indicate that the compositions of young and mature leaves of aloe vera are different and such a difference plays an important role on their efficiency as drag reducers. Tests were performed to analyse the drag reduction in a rotating apparatus and in a pipeline system and the efficiencies of leaves of different ages were compared to their composition. The main conclusion of these experiments is that the young mucilage samples, which are richer in complex polysaccharides and exhibit lower acid contents, are more efficient drag reducers.

This study presents a preliminary analysis of the chemical and thermal fuel properties of Afuze (AFZ) coal extracted from coalfields in Owan East Local Government Area of Edo State, Nigeria. The chemical properties of AFZ were examined by combined scanning electron microscopy-energy dispersive X-ray (EDX), whereas the thermal properties were deduced by thermogravimetric analysis (TGA) under flash (50 °C/min heating rate) oxidative (combustion) and non-oxidative (pyrolysis) conditions. The microstructure and morphology analysis of AFZ revealed has a compact structure comprising small-to-large, irregular shaped and exfoliated grains with a vitreous appearance typically ascribed to metal elements (Ti and Fe) kaolinite, quartz, and other clay minerals. Chemical analysis revealed carbon, oxygen, aluminium, silicon, sulphur, calcium, titanium, and iron in major and minor (trace) quantities. Thermal analysis under oxidative and non-oxidative conditions revealed degradation occurs in three stages, namely; drying or demineralisation, devolatilization or maceral degradation and the formation of char/coke or ash. Lastly, the findings showed that the temperature range for the oxidative thermal degradation process (338.58 - 756.76 °C) was higher than the non-oxidative process (378.43 - 615.34 °C). This observation can be explained by the exothermic nature of the oxidative (combustion) process, which ensures greater heat supply required to thermally soften or degrade the maceral coal components. Overall, the oxidative process yielded the residual mass (RM = 21.97%) and mass loss (ML = 78.03%). The lower ML (49.03%) but higher RM (50.97%) observed during non-oxidative degradation of AFZ could be ascribed to the largely endothermic nature of the process.

Accelerated degradation tests (ADT) are widely used in the manufacturing industry to obtain information on the reliability of components and materials, through degrading the lifespan of the product by applying an acceleration factor which causes damage to the material. The main objective is to obtain fast information which is modeled to estimate the characteristics of the material life under normal conditions of use and to save time and expenses. The purpose of this work is to estimate the lifespan distribution of gold nanoparticles stabilized with lipoic acid (GNPs@LA) through accelerated degradation tests applying sodium chloride (NaCl) as an acceleration factor. For this, the synthesis of GNPs@LA was carried out, a constant stress ADT (CSADT) was applied, and the non-linear Wiener process was proposed with random effects, error measures and different covariability for the adjustment of the degradation signals. The information obtained with the test and analysis allows us to obtain the life distribution in GNPs@LA, the results make possible to determine the guaranteed time for a possible commercialization and successful application based on the stability of the material. In addition, for the evaluation and selection of the model, the Akaike and Bootstraping criteria were used.

Metal organic frameworks (MOFs) composed of metal ions and multifunctional organic ligands are one of the most attractive porous materials. Their potential applications in gas storage, separation, catalysis, biomedicine and many other fields have attracted much attention. In this study, Nano-Mn-MOF-74 with nano size were successfully synthesized by adding acetic acid and characterized it by SEM, TEM and XRD. Furthermore, a new method to trace the degradation process of nanoMOFs through detection of ligand concentration under physiological conditions was developed.

Medical imaging is an active field of research that fosters the necessity for novel multimodal imaging probes. In this line, nanoparticle-based contrast agents are of special interest, since those can host functional entities either within their interior, reducing potential toxic effects of the imaging tracers, and on their surface, providing high payloads of probes, due to their large surface-to-volume ratio. The long-term stability of the particles in solution is an aspect usually under-tackled during probe design in research laboratories, since their performance is generally tested briefly after synthesis. This may jeopardize a later translation into practical medical devices, due to stability reasons. To dig into the effects of nanoparticle aging in solution, respect to their behavior in vivo, iron oxide stealth nanoparticles were used at two stages (3 weeks vs. 9 months in solution), analyzing their biodistribution in mice. Both sets of nanoprobes showed similar sizes, zeta potentials and morphology, as observed by DLS and TEM but, fresh nanoparticles accumulated in the kidneys after systemic administration, while aged ones accumulated in liver and spleen, confirming an enormous effect of particle aging on their in vivo behavior, despite barely noticeable changes perceived on a simple inspection of their structural integrity.

Microplastics (MPs) and nanoplastics (NPs) are distributed and transferred among the four major environmental compartments (air, water, soil, and biota) and have been already found in humans, making crucial to develop remediation technologies to tackle this kind pollution. Photocatalysis can be used to eliminate MPs present in contaminated wastewater effluents before their discharge into waterbodies. In this work, several green TiO2-based semiconductors were prepared using the extrapallial fluid (EPF) of Mytilus edulis sea water mussels as doping precursor. The semiconductors were then used as films or powders to photocatalytically degrade polystyrene (PS) NPs and MPs and polyethylene (PE) MPs. It was found that the obtention of green TiO2-based semiconductors with good characteristics for photocatalytic purposes (anatase crystalline phase, presence of porosity, activity in visible light and high surface area) seems not enough to achieve high degradation efficiency. The operational conditions of the reaction system should be also taken into account. For instance, the convenience of using semiconductors in the form of films can be overcome by their limited exposed surface area or the null adsorption of the semiconductor in the MPs particles. Additionally, crystallinity of the semiconductor can be a more determinant factor to take into account when performing photocatalysis of MPs.

Biodegradable poly(ɛ-caprolactone) (PCL) and its composites or blends have gotten a lot of attention in the last decade because of their potential applications in human life and environmental remediation. As a result, there is a growing interest in the synthesis of PCL-composites/blends and their applications. Greater efforts have been made to develop biodegradable chemical materials as adsorbents that do not pollute the environment in order to replace traditional materials. Among the numerous types of degradable materials, PCL is currently the most promising, the most popular, and the best material to be developed, and it is referred to as the "green" eco-friendly material. Membranes and adsorbents for water treatment, packaging and compost bags, controlled drug carriers, biomaterials for tissues such as bone, cartilage, ligament, skeletal muscle, skin, cardiovascular and nerve tissues are just some of the applications of this biodegradable polymer (PCL). The goal of this review is to present a brief overview of PCL, its properties, syntheses of PCL, PCL composites, and PCL blends, but to provide a detailed investigation into the utility of PCL/PCL-based adsorbing agents in the removal of dyes/heavy metal ions.

Research on healthy ageing shows that lifespan reductions are often caused by mitochondrial dysfunction. Thus, it is very interesting that the deletion of mitochondrial matrix peptidase LonP1 was observed to abolish embryogenesis, while deletion of the mitochondrial matrix peptidase ClpP prolonged survival. To unveil the targets of each enzyme, we documented the global proteome of LonP1^+/- mouse embryonal fibroblasts (MEF), for comparison with ClpP^-/- depletion. Proteomic profiles of LonP1^+/- MEF generated by label-free mass spectrometry were further processed with the STRING webserver Heidelberg for protein interactions. ClpP was previously reported to degrade Eral1 as a chaperone involved in mitoribosome assembly, so ClpP deficiency triggers accumulation of mitoribosomal subunits and inefficient translation. LonP1^+/- MEF also showed Eral1 accumulation, but no systematic effect on mitoribosomal subunits. In contrast to ClpP^-/- profiles, several components of the respiratory complex I membrane arm were accumulated, whereas the upregulation of numerous innate immune defense components was similar. Overall, LonP1 as opposed to ClpP appears to have no effect on translational machinery, instead it shows enhanced respiratory dysfunction; this agrees with reports on the human CODAS syndrome caused by LonP1 mutations.

Currently, the use of sustainable chemistry as an ecological alternative for the generation of products or processes, free of polluting substance has assumed a preponderant role. The aim of this work is propose a bioinspired, facile, at low cost, non-toxic and environmentally friendly alternative to obtaining magnetic nanoparticles whit a majority phase of magnetite (Fe₃O₄). Is important to empathize that the synthesis was based on the chemical reduction through the Cnicus Benedictus extract, whose use as reducing agent has not been reported in the synthesis of iron oxides nanoparticles. In addition, the Cnicus Benedictus is abundant endemic plant in Mexico, with several medicinal properties and a large number of natural antioxidants. The obtained nanoparticles exhibited significant magnetic and antibacterial properties and an enhanced photocatalytic activity. The crystallite size of the Fe₃O₄ nanoparticles (Fe₃O₄ NP’s) was calculated by Williamson-Hall method. The photocatalytic properties of the Fe₃O₄ NP´s were studied by kinetics absorptions models in the Congo red (CR) degradation. Finally the antibacterial effect of the Fe3O4 NP´s were evaluated mediated the Kirby-Bauer method against E. coli and S. aureus bacteria. This route offers a green alternative to obtain Fe3O4 NP´s with remarkable magnetic, photocatalytic and antibacterial properties.

The goal of this study was to analyze the forest degradation in the Reserve for San Rafael National Park, Paraguay, during the period 2005-2019. This Reserve is one of the most important forest remnants of the Upper Paraná Atlantic Forest Ecoregion. A multitemporal analysis of degradation was carried out due to the occurrence of three disturbances: forest fires, a twister and illicit crops, using the Continuous Degradation Detection (CODED) algorithm, for which 3 factors were considered: variations due to pixel in the NDFI index values before, during and after every disturbance registered. In this context, the phenomenon with the greatest impact in terms of magnitude of degradation were the forest fires of 2005, being that year at the same time, the one that reported the highest degradation values. Secondly, there are the illicit crops established until the first semester of 2019, and lastly, the twister that occurred in 2017. Our findings demonstrate that CODED algorithm can detect multi-temporal degradation events in a Subtropical Broadleaf Forest, and the post-disturbance regeneration process after every disturbance tends to occur immediately. The response in terms of degradation-regeneration is highly variable, depending of the nature and severity of each disturbance and the vegetation recovery dynamics.

Shape-memory hydrogels (SMH) are as multifunctional, actively-moving polymers of interest in biomedicine. In loosely crosslinked polymer networks gelatin chains may form triple helices, which can act as temporary netpoints in SMH, depending on the presence of salts. Here, we show programming and initiation of the shape-memory effect of such networks based on a thermomechanical process compatible with the physiological environment. The SMH were synthesized by reaction of glycidylmethacrylated gelatin with OEG α,ω-dithiols of varying crosslinker length and amount. Triple helicalization of gelatin chains is shown directly by wide-angle X-ray scattering and indirectly via the mechanical behavior at different temperatures. The ability to form triple helices increased with the molar mass of the crosslinker. Hydrogels had storage moduli of 0.27-23 kPa and Young’s moduli of 215-360 kPa at 4 °C. The hydrogels were hydrolytically degradable, with full degradation to water soluble products within one week at 37 °C and pH = 7.4. A thermally-induced shape-memory effect is demonstrated in bending as well as in compression tests, in which shape recovery with excellent shape recovery rates Rr close to 100% were observed. In the future, the material presented here could be applied e.g. as self-anchoring devices mechanically resembling the extracellular matrix.

Lignocellulosic fibers are widely applied as composite reinforcement due to their properties. The thermal degradation behavior determines the maximum temperature in which the fiber can be applied without significant mass loss. It is possible to determine these temperatures using Thermogravimetric Analysis (TG). In particular, when curves are obtained at different heating rates, kinetic parameters can be determined and more detailed characteristics of the material are obtained. However, every curve obtained at a distinct heating rate demands material, cost, and time. Methods to predict thermogravimetric curves can be very useful in the materials science field and in this sense mathematical approaches are powerful tools if well employed. For this reason, in the present study, curaua TG curves were obtained at three different heating rates (5, 10, 20, and 40 °C.min-1) and Vyazovkin kinetic parameters were obtained. After, the experimental curves were fitted using an artificial neural network (ANN) approach followed by a Surface Response Methodology (SRM). Curves at any heating rate between the minimum and maximum experimental heating rates were obtained with high reliability. Finally, Vyazovkin kinetic parameters were tested again with the new curves showing similar kinetic parameters from the experimental ones. In conclusion, due to the capability to learn from the own data, ANN combined with SRM seems to be an excellent alternative to predict TG curves that do not test experimentally, opening the range of applications.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

This work presents the dynamics of forest clearing in the Brazilian Amazon during the period 2006–2019 in which includes the approval of the new Brazilian Forest Code in 2012. The study was carried out in the Brazilian Amazon, Pará State and in the municipality of Novo Progresso (Pará State). The analysis was based on deforestation and fire hotspot datasets issued by the Brazilian Institute for Space Research (INPE), produced based on optical and thermal sensors onboard different satellites. Deforestation data was also used to assess greenhouse gas (GHG) emissions from the slash-and-burn practices. The work showed a good correlation between the occurrence of fires in the newly deforested area in the municipality of Novo Progresso and the slash-and-burn practices. The same trend was also observed in the Pará State, suggesting a common practice along the deforestation arch. The study indicated positive coefficients of determination of 0.72 and 0.66 between deforestation and fire occurrences for the municipality of Novo Progresso and Pará State, respectively. The increased number of fire occurrences in the primary forest suggests possible ecosystem degradation. Deforestation reported for 2019 surpassed 10,000 km2, a significant intensification comparatively higher than the previous ten years which was on an average of 6,760 km2. The steady increase of deforestation in the Amazon after 2012 has been a worldwide concern because of the forest loss itself as well as the massive GHG emitted in the Brazilian Amazon (295 million tons of net CO2 equivalent in the year 2019). Better correlation of deforestation and fires occurrences reported from satellite images confirmed the slash-and-burn practice and the secondary effect of deforestation, which degrades primary forest surrounding the deforested areas.

The large areas being targeted for tropical forest restoration as part of the UN Decade on Ecosystem Restoration will have major consequences for the flow of water through landscapes. Whilst the prevailing mantra that ‘more forest implies less streamflow’ remains true in terms of annual water yields, we demonstrate that opportunities for increased tree cover to improve seasonal flow regimes of streams, particularly baseflows, are important. We discuss several potential positive feedbacks of forest restoration on hydrological processes at various scales, including ‘trade-offs’ between changes in vegetation water use and infiltration after foresting degraded land; the recovery of the capacity of vegetation to capture ‘occult’ precipitation in specific coastal and montane settings; and enhanced moisture recycling and transport at various scales. Modelled changes in baseflow after foresting all degraded land climatically capable of carrying forest in the tropics suggested a positive effect in 10% of the land. For an additional 8%, the effect was predicted to be about neutral (<2 mm/y). We conclude that a more positive narrative regarding the relationship between tropical forestation and water availability is justified. It is time for greater involvement of hydrologists and atmospheric scientists in the development and assessment of forest landscape restoration efforts.

Human NAD(P)H:quinone oxidoreductase 1 (NQO1) is a multi-functional protein whose alteration is associated with cancer, Parkinson´s and Alzheimer´s diseases. NQO1 displays a remarkable functional chemistry, capable of binding different functional ligands that modulate its activity, stability and interaction with proteins and nucleic acids. Our understanding on this functional chemistry is limited by the difficulty of obtaining structural and dynamic information on many of these states. Herein, we have used hydrogen/deuterium exchange monitored by mass-spectrometry (HDXMS) to investigate the structural dynamics of NQO1 in three ligation states: without ligands (NQO1apo), with FAD (NQO1holo) and with FAD and the inhibitor dicoumarol (NQO1dic). We show that NQO1apo has a minimally stable folded core holding the protein dimer and with FAD and dicoumarol ligand binding sites populating binding non-competent conformations. Binding of FAD significantly decreases protein dynamics and stabilizes the FAD and dicoumarol binding sites as well as the monomer:monomer interface. Dicoumarol binding further stabilizes all three functional sites, a result not previously anticipated by available crystallographic models. Our work provides an experimental perspective into the communication of stability effects through the NQO1 dimer, valuable to understand at the molecular level the effects of disease-associated variants, post-translation modifications and ligand binding cooperativity in NQO1.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

We propose a deep learning algorithm that directly compensates for luminance degradation owing to the deterioration of organic light emitting diode (OLED) devices to address the burn-in phenomenon of OLED displays. Conventional compensation circuits are encumbered by a high cost of development and manufacturing processes owing to their complexity. However, given that deep learning algorithms are typically mounted on a system on chip (SoC), the complexity of the circuit design is reduced, and the circuit can be reused by re-learning only the changed characteristics of the new pixel device. The proposed approach comprises deep feature generation and multi-stream self-attention, which decipher the importance of the variables, and the correlation between burn-in-related variables. It also utilizes a deep neural network that identifies the nonlinear relationship between the extracted features and luminance degradation. Thereafter, the luminance degradation is estimated from the burn-in-related variables, and the burn-in phenomenon can be addressed by compensating for the luminance degradation. The experimental results revealed that compensation was successfully achieved within an error range of 4.56%, and demonstrate the potential of a new approach that can mitigate the burn-in phenomenon by directly compensating for pixel-level luminance deviation.

The cytosolic PNGase (peptide:N-glycanase; Png1 in yeast; NGLY1/Ngly1 in human/mice), also known as peptide-N4-(N-acetyl-beta-glucosaminyl)-asparagine ami-dase, is a well-conserved deglycosylation enzyme (EC 3.5.1.52) which catalyzes the non-lysosomal hydrolysis of an N(4)-(acetyl-β-D-glucosaminyl) asparagine residue into N-acetyl-β-D-glucosaminylamine and a peptide containing an aspartate residue. This enzyme (NGLY1) plays essential roles in clearance of misfolded or unassembled gly-coproteins through a process named ER-associated degradation (ERAD). Accumulating evidence also points out that NGLY1 deficiency can cause an autosomal recessive hu-man genetic disorder associated with abnormal development and congenital disorder of deglycosylation. In addition, the loss of NGLY1 can affect multiple cellular pathways, including but not limited to NFE2L1 pathway, Creb1/Atf1-AQP pathway, BMP path-way, AMPK pathway, and SLC12A2 ion transporter, which might be the underlying reasons for a constellation of clinical phenotypes of NGLY1 deficiency. The current comprehensive review indeed uncovers the detailed NGLY1’s structure and its im-portant roles for participation in ERAD, involvement in CDDG and potential treatment for NGLY1 deficiency.

Enteric methane (CH4) emitted by ruminant species is known as one of the main greenhouse gases produced by the agricultural sector. The objective of this study was to evaluate the chemical composition, in vitro gas production, dry matter degradation (DMD), digestibility, CO2 production and CH4 mitigation potential of five tropical tree species with novel forage potential including: Spondias mombin, Acacia pennatula, Parmentiera aculeata, Brosimum alicastrum and Bursera simaruba mixed at two levels of inclusion (15 and 30%) with a tropical grass (Pennisetum purpureum). Crude protein content was similar across treatments (135 g kg-1 DM), while P. purpureum was characterized by a high content of acid detergent fiber (335.9 g kg-1 DM) and B. simaruba by a high concentration of condensed tannins (20 g kg-1 DM). Likewise, A. pennatula and P. aculeata were characterized by a high content of cyanogenic glycosides and alkaloids respectively. Treatments SM30-PP70 (30% S. mombin + 70% P. purpureum) and BA30-PP70 (30% B. alicastrum + 70% P. purpureum) resulted in superior digestibility than P. purpureum, while in the AP30-PP70 (30% A. pennatula + 70% P. purpureum) was lower than the control treatment (P≤0.05). At 24 and 48 h, treatments that contained P. aculeata and B. alicastrum produced higher CH4 ml g-1 DOM than P. purpureum (P≤0.05). The inclusion of B. simaruba at 30% reduced CH4 at 25% compared to P. purpureum. Tropical tree species can improve the nutritional quality of ruminant rations and reduce CH4 emissions to consequently contribute to the development of sustainable ruminant production systems that generate diverse ecosystem services.

For the decontamination of surfaces in the food production industry, plasma generated compounds (PGCs) such as plasma-treated water (PTW) or plasma processed air (PPA) offer many promising possibilities for future applications. Therefore, the antimicrobial effect of water treated with microwave-induced plasma (MidiPLexc) on Pseudomonas fluorescens biofilms was investigated. 10 ml deionized water was treated with the MidiPLexc plasma source for 100 s, 300 s and 900 s (pre-treatment time) and the bacterial biofilms were exposed to the PTW for 1 min, 3 min and 5 min (post treatment time). To investigate the influence of PTW on P. fluorescens biofilms, microbiological assays (CFU, fluorescence and XTT assay) and imaging techniques (fluorescence microscopy, confocal laser scanning microscopy (CLSM), and atomic force microscopy (AFM)) were used. The CFU showed a maximum reduction of 6 log10 by using 300 s pre-treated PTW for 5 min. Additionally, a maximum reduction of 81 % for the viability of the cells and a 92 % reduction in the metabolic activity of the cells was achieved by using 900 s pre-treated PTW for 5 min. The microscopic images showed evident microbial inactivation within the biofilm even at the shortest pre treatment (100 s) and post-treatment (1 min) times. Moreover, reduction of the biofilm thickness and increased cluster formation within the biofilm was detected. Morphologically, the fusion of cell walls into a uniform dense cell mass. The findings correlated with a decrease in the pH value of the PTW, which forms the basis for the chemically active components of PTW and its antimicrobial effects. These results, provide valuable insights into the mechanisms of inactivation of biofilms by plasma generated compounds (PGCs) such as PTW and thus allow for further parameter adjustment for applications in food industry.

In China, the production of crop straw has been estimated to be approximately 800 Million tons yearly of which about 40% was burned. Corn stover is one of the main agricultural wastes in China. It has shown that lignin in corn stover could be effectively removed byMyrothecium verrucaria. The effects of the pretreatment of corn strover by Myrothecium verrucaria on compost were studied. The results showed that corn stover pretreatment by Myrothecium verrucaria, the Cellulose, Hemicellulose, and lignin were degraded and the results were 33.43%, 11.53% and 18.70% respectively. Scanning electron microscope (SEM) analysis showed that the surface structure of corn stover was changed. Fourier transform infrared spectroscopy (FTIR) analysis showed that the degradation products of lignin were increased. The exposed area of cellulose and hemicellulose was increased. Compared with the control group, the pH value was stable and the temperature was higher. The content of nitrogen in the material decreased, while the contents of total phosphorus and total potassium increased.The C/N ratio of materials decreased after composting.The results showed that the pretreatment of Myrothecium verrucaria improve the degradation of lignocelluloses, a great contribution was made to reduce the causes loss of plant nutrient and to fight against environmental pollution.

Land degradation is a critical issue globally putting our future generations at risk. The decrease in farm productivity over the years is evidence of land degradation severity in Nepal. Among the many strategies in place, agroforestry, which is an integrated tree-based farming, is widely recommended to address this productivity issue. This paper thoroughly examines what influences the choice of agroforestry adoption by farmers and what discourages the adoption. For this, a total of 288 households were surveyed using a structured questionnaire. Two agroforestry practices were compared with conventional agriculture with the help of the Multinomial Logistic Regression (MNL) model. The likelihood of adoption was found to be influenced by gender; the male-headed households were more likely to adopt the tree-based farming practice. Having a source of off-farm income was positively associated with the adoption decision of farmers. Area of farmland was found being the major constraint to agroforestry adoption for smallholder farmers. Some other variables that affected positively included livestock herd size, provision of extension service, home-to- forest distance, farmers’ group membership and awareness of farmers about environmental benefits of agroforestry. Irrigation was another adoption constraint that the study area farmers were faced with. The households with means of transport and with larger family (household) size were found to be reluctant towards agroforestry adoption. A collective farming practice could be a strategy to engage the smallholder farmers in agroforestry.

The objective of this work is to identify the mechanism of dropwise condensation on a smooth solid surface. We investigate the stable dropwise condensation that occurs at a droplet growth rate of 1 µm/s in diameter on a gold-coated glass surface. Additionally, we present our observations on unstable dropwise condensation, i.e., degradation of dropwise condensation of steam on a gold surface. The Surface Plasmon Resonance Imaging (SPRi) approach used in this study has lateral resolutions of 4-10 µm, thickness resolutions of 0.1-1 nm, and temporal resolutions of 200-10,000 frames per second (FPS). SPRi is used to evaluate the existence and structure of thin films and occurrence of initial nuclei during condensation. Visualization of the onset of stable dropwise condensation suggests droplets form at heterogeneous nucleation sites and that no film greater than a monolayer exists on the surface before the formation of droplets. Observation of the unstable dropwise condensation of steam shows the existence of water films that are several nanometers thick between droplets. This work shows that neither the nucleation theory or film rupture theory can individually explain the physics of dropwise condensation. Therefore, there is a need for a more comprehensive theory that can explain the mechanism of dropwise condensation.

Sub-micron o/w emulsions coated with chitosan have been used for drug delivery, quorum sensing inhibition and vaccine development. To study interactions with biological systems, nanocapsules have been fluorescently labelled in previous works, but it is often difficult to distinguish the released label from intact nanocapsules. In this study, we present advanced labelling strategies based on FRET measurements for chitosan-coated nanocapsules and investigate their dissolution and degradation. We used FRET measurements of nanocapsules loaded with equimolar concentrations of two fluorescent dyes in their oily core and correlated them with DLS count rate measurement and absorbance measurements during their disintegration by dissolution. Using count rate measurements, we also investigated the enzymatic degradation of nanocapsules using pancreatin and how protein corona formation influences their degradation. Of note, nanocapsules dissolved in ethanol, where FRET decreased simultaneously with count rate, and absorbance caused by nanocapsule turbidity, indicating increased distance between dye molecules after their release. Nanocapsules were degradable by pancreatin in a dose dependent manner, and showed a delayed enzymatic degradation after protein corona formation. We present here novel labelling strategies for nanocapsules that allow us to judge their status and an in vitro method to study nanocapsule degradation and the influence of surface characteristics.

We identified a novel heterozygous hypofibrinogenemia, γY278H (Hiroshima). To demonstrate the cause of reduced plasma fibrinogen levels (functional level: 1.12 g/L and antigenic level: 1.16 g/L), we established γY278H fibrinogen-producing Chinese hamster ovary (CHO) cells. An enzyme-linked immunosorbent assay demonstrated that synthesis of γY278H fibrinogen inside CHO cells and secretion into the culture media were not reduced. Then, we established an additional five variant fibrinogen-producing CHO cell lines (γL276P, γT277P, γT277R, γA279D, and γY280C) and performed further investigations. We have already established 33 γ-module variant fibrinogen-producing CHO cell lines including 6 cell lines in this study, but only the γY278H and γT277R cell lines showed disagreement, namely recombinant fibrinogen production was not reduced but the patients’ plasma fibrinogen level was reduced. Finally, we performed fibrinogen degradation assays and demonstrated that the γY278H and γT277R fibrinogens were easily cleaved by plasmin whereas their polymerization in the presence of Ca2+ and “D:D” interaction was normal. In conclusion, our investigation suggested that patient γY278H showed hypofibrinogenemia because γY278H fibrinogen is secreted normally from the patient’s hepatocytes but had accelerated degradation by plasmin in the circulation.

Unplanned urbanisation and industrialisation have severely degraded natural ecosystems, particularly wetlands. The Ganges-Brahmaputra Basin support 630 million inhabitants; yet continue to be altered rapidly, jeopardizing the region’s social and ecological integrity. By conducting qualitative interviews and participant observation in a wetland dependent village located in the Lower Gangetic Floodplains we investigated how degrading wetlands in sub-urban landscapes were affecting socio-ecological systems. Not only did the wetlands provide livelihood options, mainly fishing and farming, but also provided prestige and autonomy. Vulnerable sections of the society across class, age and gender were solely dependent on the wetland. In absence of political will to safeguard wetland health, industries emerged by altering wetlands, which hampered local community’s livelihood and lifestyle. Further, our study demonstrated that local ecological knowledge could provide qualitative baseline information for fast-tracking identification of important wetlands and creating inventories to initiate wetland conservation and management. Finally, we recommend local governance structures should be strongly tied to international or national wetland policies so that wetland functions along with human health and well-being could be sustained. We strongly advocate that contradictions in policies be resolved to strengthen efforts to conserve wetlands which provide resilience to marginal communities in the face of calamities.

In recent years, many studies have highlighted the consistent finding of amoxicillin in waters destined for wastewater treatment plants, in addition to superficial waters of rivers and lakes in both Europe and North America. In this paper, the amoxicillin degradation pathway was investigated by simulating the chlorination process normally used in a wastewater treatment plant to reduce similar emerging pollutants at three different pH values. The structures of 16 isolated degradation byproducts (DPs), one of which was isolated for the first time, were separated on a C-18 column via a gradient HPLC method. Then, combining mass spectrometry (MALDI-MS/TOF) and nuclear magnetic resonance, we compared commercial standards and justified a proposed formation mechanism beginning from the parent drug. Microbial growth inhibition bioassays with Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were performed to determine the potential loss of antibacterial activity in isolated degradation byproducts. An increase of antibacterial activity in the DPs was observed compared to the parent compound.

Starch is considered a major nutritional factor of maize (Zea mays L.) kernels, and can be influenced by the type of endosperm. The effects of endosperm type (vitreous and non-vitreous) and type of soil (clay and sand) on the starch content of kernels of maize, and on the in vitro degradation of starch were investigated in the rumen fluid after harvesting at 6 different maturity stages during 2008 and five different maturity stages in 2009. Starch degradation, in rumen fluid, was determined after 6 h, 12 h and 20 h of incubation, using the technique of gas production. A positive linear relationship was observed during gas production (ml gas/g organic matter) and starch degradation (g kg^-1 starch) at all incubation times, with starch contents of maize kernels to a certain limit of starch accumulation (i.e. at starch contents 451-519 g/kg OM) and negative relationship afterwards. This suggests significant effects of maturity on ruminal starch degradation of maize kernels. At each harvest date, ruminal starch degradation of maize kernels was affected by crop genotype as well as soil type. The in vitro ruminal degradation potential of starch in maize kernels was influenced by the nature of the endosperm, with a higher degradation of non-vitreous kernels than of vitreous kernels. The rumen starch degradation was also influenced by type of soil, with better degradation on clay than sandy soil. For all the incubation times and maturity stages the effects of genotype, soil type and maturity stage were consistent in rumen fluid.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

An increase in air temperature leads to a significant transformation of the relief and landscapes of the Arctic. The rate of permafrost degradation, posing a profound change in the Arctic landscape, depends on air temperature, vegetation cover, type of soils, surface and ground waters. The existing international circumpolar programs dedicated to monitoring the temperature state of permafrost TSP (Thermal State Permafrost) and active layer thickness CALM (Circumpolar Active Layer Monitoring) are not sufficient for a comprehensive characterization of geocryological conditions. Yet, no standardized protocol exists for permafrost monitoring and related processes. Here, we propose a novel multi-parameter monitoring protocol and implement for two sites in the European part of the Russian Arctic: the Yary site along the coast of the Baydaratskaya Bay in the Kara Sea (68.9°N) within the continuous permafrost area and the Hanovey site in the Komi Re-public (67.3°N) within the discontinuous permafrost one. The protocol includes drilling boreholes, determining the composition and properties (vegetation cover and soils), snow cover measure-ment, geophysical imaging, active layer estimation and continuous ground temperature meas-urements. Ground temperature measured in 2014 – 2020 revealed that amplitudes of surface tem-perature fluctuation had no significant difference between the Yary and Hanovey sites, while that the mean annual temperatures between the areas had a considerable difference of greater than 3.0 °C. The period of the presence of the active layer changed with the year (e.g., ranging between 135 and 174 days in the Yary site), showing longer when the air temperatures in summer and the preceding winter were higher. Electrical resistivity tomography (ERT) allowed determining the permafrost distribution and active layer thicknesses. Thermometry results were consistent with our geophysical data. Analyzing the composition and properties of frozen soils helped better interpret the data of geophysical and temperature measurements. Our work by integrating the study of the soil properties, ground temperatures, and ERT allowed fully characterize these sites, suggesting that it helps better understand the thermal state in any other research sites in the European north of Russia. Our suggested monitoring protocol enables calibrating and verifying the numerical and analytical models of the heat transfer through the earth’s surface.

Gold nanoparticles, were deposited in titanium oxide (TiO2) Degussa-P25 with the Photodeposition method in the presence of UV light at different concentrations. It was determined by diffuse reflectance (DF), Scanning electron microscopy (SEM), that the Photodeposition method is effective for the inclusion of gold particles on the surface. The catalyst band gap showed a reduction to 2.9 e.V, as well as it was observed that the gold-doped catalyst shows absorption in the visible light range around 500 to 600 nm. The percentage of deposited gold nanoparticles was determined by energy dispersive spectroscopy (EDS). The experimental data were analyzed using different analytical techniques (UV-Vis spectrophotometry, TOC total organic carbon), with these results a carbon-based mass balance and reaction kinetics were generated using the Langmuir-Hinshelwood (LH-HW) heterogeneous catalysis model. For the estimation of the kinetic constants, the non-linear regression of the Levengerd Marquad algorithm was used, with these results, kinetic models of the degradation of the molecule and the generation and consumption of Organic Intermediate Products (OIP) were generated.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

Endothall dipotassium salt and monoamine salt are herbicide formulations used for controlling submerged aquatic macrophytes and algae in aquatic ecosystems. Microbial activity is the primary degradation pathway for endothall. To better understand what influences endothall degradation, we conducted a mesocosm experiment to 1) evaluate the effects of different water and sediment sources on degradation, and 2) determine if degradation was faster in the presence of a microbial community previously exposed to endothall. Endothall residues were determined with LC-MS at intervals to 21 days after endothall application. Two endothall isomers were detected. Isomer-1 was abundant in both endothall formulations, while isomer-2 was only abundant in the monoamine endothall formulation and was more persistent. Degradation did not occur in the absence of sediment. In the presence of sediment degradation if isomer-1 began after a lag phase of 5-11 days and was almost complete by 14 days. Onset of degradation occurred 2-4 days sooner when the microbial population was previously exposed to endothall. We provide direct evidence that the presence and characteristics of sediment are of key importance in the degradation of endothall in an aquatic environment, and that monoamine endothall has two separate isomers that have different degradation characteristics.